IMPRESSA S70
IMPRESSA X70
Instructions for use
07/2001
Fig. 1
Fig. 4
Fig. 7
Fig. 2
Fig. 5
Fig. 8
Fig. 3
Fig. 6
Fig. 9
A
B
12
14 15
16
13
D
C
B
A
E
F
17
18
19
20
11
10
9
8
G
H
7
21
6
5
4
22
3
2
1
Operating elements Jura Impressa S70/X70
1 Drip tray / residual water container
2 Drip tray cover
3 Cover for programming keys
4 Coffee key for 2 normal cups
5 Coffee key for 1 normal cup
6 Coffee key for 2 small cups
7 Coffee key for 1 small cup
8 Key for special coffee
9 ON/OFF switch
10 Rinsing key
11 Display dialogue system
12 Water tank with carrying handle
13 Cover for bean container and aroma protection lid
14 Cover for pre-ground coffee filler funnel
15 Height-adjustable coffee-spout
16 Cup warming tray
17 Selector key for steam
18 Selector key for hot water
19 Selector switch for coffee or hot water/steam
20 Pivoting nozzle for hot water/steam
21 Frothing nozzle
22 Container for coffee grounds
Programming keys
A
B
Change filter
Back-setting of criteria / changing of memory indications
downwards
C
D
E
F
G
Open program
Selector switch for pre-ground coffee
Key for cleaning program
Correction of program / close
Forward-setting of criteria / changing of memory indicati-
ons up-wards
H
Key for decalcifying program
12.5 Programming WATER HARDNESS.........page 13
12.6 Programming ECONOMY MODE ............page 13
12.7 Programming TIMER CLOCK ................page 13
12.8 Programming automatic switch on time..page 13
12.9 Programming automatic switch off time .page 14
12.10 Cup counter .......................................page 14
12.11 Programming language selection ...........page 14
N
Table of contents
Jura Impressa S70/X70
1. Description .................................................page
2. Safety instructions.......................................page
2.1 Warnings ...........................................page
2.2 Safety precautions ..............................page
3. Check before use .........................................page
3.1 Checking mains voltage........................page
3.2 Checking fuse.....................................page
3.3 Adding coffee beans ............................page
3.4 Adjusting grinder ................................page
4. Preparing machine .......................................page
5. Rinsing the machine.....................................page
6. Adjusting for water hardness.........................page
7. Use of Claris filter cartridges ........................page
7.1 Placing filter ......................................page
7.2 Replacing of filter ...............................page 10
8. Drawing off coffee .......................................page 10
8.1 Drawing off powder coffee ...................page 10
9. Drawing off hot water ..................................page 11
10. Using steam................................................page 11
11. Switching off machine..................................page 11
12. Programming ..............................................page 12
12.1 Programming POWDER QUANTITY........page 12
12.2 Programming coffee temperature ..........page 12
12.3 Programming water quantity.................page 12
12.4 Programming FILTER ..........................page 13
7
7
7
7
8
8
8
8
8
8
8
9
9
9
12.12 Program key
..................................page 14
13. Care and maintenance ..................................page 14
13.1 Fill water ...........................................page 14
13.2 Empty grounds container ....................page 14
13.3 Empty drip tray .................................page 14
13.4 Fill beans ..........................................page 15
13.5 Removing foreign objects ....................page 15
13.6 Clean machine ...................................page 15
13.7 Unit calcified .....................................page 15
13.8 Cleaning metal contacts ......................page 15
13.9 General cleaning instructions ...............page 15
13.10 Regular servicing ................................page 16
14. Cleaning.....................................................page 16
15. Decalcifying ................................................page 16
15.1 Decalcifying coffee sector ....................page 16
15.2 Decalcifying water sector .....................page 17
16. Disposal......................................................page 17
17. Tips for a perfect coffee ...............................page 17
18. Messages....................................................page 18
19. Problems ....................................................page 19
20. Legal information.........................................page 20
21. Technical specifications ................................page 20
6
Important information for the user
2. Safety instructions
2.1 Warnings
Thank you for choosing this Jura product.
Ⅲ Children are unaware of the dangers that electrical machines
represent. Therefore children should never be left unsupervised
with electrical machines.
Please study these instructions carefully before using your new
machine and keep them in a safe place for easy reference in the
future.
Ⅲ This machine should only be used by people who have read and
understood the operating instructions.
Should you require further information or should particular pro-
blems occur that are not dealt with in these operating instructions
in sufficient detail for you, then please ask your local dealer for
the information you require or contact Jura Elektroapparate AG
directly.
Ⅲ Never use a faulty machine or one with a damaged power cable.
Ⅲ Never immerse the machine in water.
2.2 Safety precautions
Ⅲ Never expose the machine to the effects of rain, snow or frost
and never operate it with wet hands.
Ⅲ Place your machine on a solid level surface. Never leave it on a
surface that is warm or hot (hob etc.). Choose a location that is
inaccessible for children or pets.
E
Ⅲ Remove plug from power socket if an absence for a longer
period of time (holidays etc.) is planned.
1. Description
Ⅲ Always remove plug from power socket before cleaning.
Ⅲ When removing plug from power socket, never tug on the cord
or on the machine itself.
This fully-automatic espresso/coffee machine impresses because of
its user-friendly operational mode and its ingenious technology. In
just one brewing-process it can prepare 1 or 2 cups of excellent,
professional-quality espresso/coffee with guaranteed froth. Origi-
nating from professional sectors and having been refined and fur-
ther developed by Jura, the Intelligent Pre Brew Aroma System
(I.P.B.A.S©) ensures full coffee aroma. The Impressa S70 enables
you to adapt the resulting coffee to your personal taste due to the
possibility of programming coffee-powder and water quantities as
well as the brewing temperature.
Ⅲ Never repair or open the machine yourself. All repairs should be
performed by authorised service centres only using original Jura
spare parts and accessories.
Ⅲ The machine is connected to the mains power socket via an
electric cable. Ensure that no-one trips over this cable and pulls
down the machine. Keep children and animals at a distance to
the machine.
Ⅲ Never put the machine or even parts of it in the dishwasher.
The machine works fully-automatically at the press of a key. A
decoded text-display shows messages and simplifies the operation
considerably. Because of the integrated rinsing, cleaning and
decalcifiying programs care and maintenance is quick and easy.
Ⅲ To prevent overheating place the machine in an airy place.
7
Ⅲ If using acidic decalcifying agents be sure to immediately re-
move any splashes and drops from delicate surfaces, especially
natural stone and wooden surfaces, or take corresponding pre-
cautions.
Ⅲ You have the following possibilities:
the smaller the dots, the finer the grinding
the bigger the dots, the coarser the grinding
The grinding grade should only be adjusted while the grinder
is working.
3. Check before use
3.1 Checking mains voltage
4. Preparing machine
The machine is set for the correct voltage before leaving our
factory. Ensure that your mains voltage corresponds to the details
quoted on the rating plate attached to the bottom of the machine.
Ⅲ Switch your machine on by pressing ON/OFF key
chine adjusts fully-automatically to the starting position.
. The ma-
Ⅲ
FILL WATER
Ⅲ Remove water tank and rinse well with clear tap-water.
3.2 Checking fuse
Ⅲ Fill water tank and replace. Make sure that tank engages well.
(Abb. ....).
The machine is designed for a current of 10 amps. Check that an
appropriate fuse is fitted.
Ⅲ
Ⅲ
PLEASE WAIT
RINSE UNIT
3.3 Adding coffee beans
Ⅲ Place a container under the coffee-spout (15) and press rinsing
key
Ⅲ Lift up cover of the bean container (13) and remove aroma pro-
tection lid.
.
Ⅲ
Ⅲ
UNIT RINSING
Ⅲ Clean out any dirt or foreign object from the bean container.
COFFEE READY
Ⅲ Fill the grinder container with coffee beans, replace aroma pro-
tection lid and close the cover.
5. Rinsing the machine
3.4 Adjusting grinder
Ⅲ
RINSE UNIT
Ⅲ Place an empty cup under the coffee-spout (15).
Ⅲ Press rinsing key
You can adjust the grinder to the roast of your coffee. We recom-
mend the following:
.
for a light roast Ǟ a finer adjustment
for a dark roast Ǟ a coarser adjustment
If the machine has been switched off and has already cooled
down it will be necessary to carry out this rinsing function
when the machine is switched on again.
After switching off the machine, the rinsing sets off automa-
tically.
Ⅲ Open the cover of the bean container (13).
Ⅲ To adjust grinding turn selector switch (Fig. 1) to the desired
position.
8
6. Adjusting for water hardness
Ⅲ
PRESS KEY / POWDER QUANTITY
+
Ⅲ Press key
several times until the following message appears:
The water is heated inside the machine. With use, this leads to
calcium deposits (furring) forming on the machine. This will be
automatically indicated on the display.
For this reason, it is necessary to adjust the machine to the
hardness of your local water before you use it for the first time.
Use the enclosed test-sticks for this purpose.
Ⅲ
HARDNESS LEVEL 3
P
Ⅲ By pressing key
hardness level flashes
you can hear an acoustic signal, the set
+
Ⅲ You can alter the hardness level by pressing key - or . After
setting, press key
can be heard.
P
once again to confirm. An acoustic signal
1° water hardness on the German scale represents 1.79° on
the French scale.
N
Ⅲ Press key
to return to stand-by-status.
The machine has got 5 hardness settings to choose from. While
adjusting the chosen grade is shown on the display.
7. Use of Claris filter cartridges
Under proper implementation of Claris filter cartridges,
decalcifying of the machine becomes unnecessary. For
further information, please read the brochure “Claris. Tough
to calcium deposits, gentle to your coffee machine”.
The symbols on the display mean:
HARDNESS
LEVEL – –
water hardness function is switched off
HARDNESS
LEVEL 1
German water hardness
French water hardness
1 – 7°
1.79 – 12.53°
7.1 Placing filter
E
Ⅲ Pull up cartridge mounting. Pressing lightly, place the filter car-
tridge in the water tank (Fig. 2).
HARDNESS
LEVEL 2
German water hardness
French water hardness
8 – 15°
14.32 – 26.85°
Ⅲ Pull down cartridge mounting, until it engages audibly.
HARDNESS
LEVEL 3
German water hardness
French water hardness
16 – 23°
28.64 – 41.14°
Ⅲ Fill water tank with cold, fresh tap-water and replace it.
Ⅲ Switch the machine on by pressing key
ON/OFF.
HARDNESS
LEVEL 4
German water hardness
French water hardness
24 – 30°
42.96 – 53.7°
P
Ⅲ Open front cover (3) and press key
until you hear an acoustic
signal.
The machine is adjusted to hardness level 3 before it leaves the
factory. You can alter this setting by following the instructions
below:
Ⅲ
PRESS KEY / POWDER QUANTITY
+
Ⅲ Press key
several times until the following message appears:
Ⅲ
FILTER NO
Ⅲ Switch the machine on by pressing ON/OFF key
. The
P
Ⅲ By pressing key
you can hear an acoustic signal.
machine adjusts fully-automatically to the starting position.
Ⅲ
NO flashes
Ⅲ
PLEASE WAIT
+
Ⅲ You can alter the setting by pressing key - or
.
P
Ⅲ Open cover (3) and press key
signal
, until you hear an acoustic
9
Ⅲ Place a sufficiently large container (approx. 1 litre) under the
Ⅲ
YES flashes
pivoting nozzle (20). Turn selector switch for coffee or hot
P
Ⅲ To confirm press key
. An acoustic signal can be heard.
water/steam (19) to position
.
Ⅲ
RINSE FILTER / OPEN TAP
Ⅲ
Ⅲ
Ⅲ
PLEASE WAIT / FILTER RINSING
CLOSE TAP (the system gives off steam)
COFFEE READY
Ⅲ Place a sufficiently large container (approx. 1 litre) under the
pivoting nozzle (20). Turn selector switch for coffee or hot wa-
ter/steam (19) to position
.
Ⅲ
PLEASE WAIT / FILTER RINSING
CLOSE TAP (the system gives off steam)
FILTER YES
The water might be slightly discoloured (this is not damaging
to the health).
Ⅲ
Ⅲ
N
Ⅲ Press key
.
8. Drawing off coffee
Ⅲ
COFFEE READY
Ⅲ Switch the machine on by pressing key ON/OFF
.
Ⅲ
Ⅲ
PLEASE WAIT
The water might be slightly discoloured (this is not dama-
ging to the health).
RINSE UNIT
Ⅲ Put an empty cup under the coffee-spout (15) and press rinsing
key
.
7.2 Replacing of filter
Ⅲ
Ⅲ
UNIT RINSING
After drawing off 50 litres the filter loses its effect.
COFFEE READY
Ⅲ
REPLACE FILTER
Ⅲ Put 1, respectively 2 cups under the coffee-spout and press the
required key. The pre-brew system (I.P.B.A.S©) moistens the
coffee powder, briefly interrupts the flow and then starts the real
brewing process.
If only a little water is drawn off the filter should be changed every
2 months. However no message will appear on the display. You
will find a special turntable on the cartridge mounting to set the
replacement date.
Ⅲ Empty water tank and pull up cartridge mounting. Pressing light-
ly, place the filter cartridge in the water tank (Fig. 2).
You can interrupt the flow of coffee at any time by simply
pressing any of the coffee keys.
Ⅲ Pull down cartridge mounting, until it engages audibly.
To obtain a perfect head of froth adjust the coffee-spout (15)
to the size of your cups (Fig. 3).
Ⅲ Fill water tank with cold, fresh tap-water and replace it.
Ⅲ Switch the machine on by pressing key ON/OFF
.
8.1 Drawing off powder coffee
Ⅲ Open front cover (3) and press key , until you hear an acoustic
signal.
Ⅲ Open cover (3)
Ⅲ
RINSE FILTER / OPEN TAP
Ⅲ Press selector key for pre-ground powder coffee
.
10
10. Using steam
Ⅲ
FILL POWDER
Ⅲ Now put 1 or 2 level measuring spoons of pre-ground coffee into
the pre-ground powder funnel (14).
Steam can be used for heating up liquids as well as for frothing up
milk for cappuccinos.
To heat up liquids remember to push the frothing nozzle (21) up.
For frothing up liquids push the frothing nozzle (21) down (Fig. 4).
Ⅲ Put 1, respectively 2 cups under the coffee-spout and press the
required key.
Ⅲ Press selector key for steam
lamp turns into a constant light.
. Wait until the flashing of the
Never use soluble instant coffee or quick coffee. Only use
coffee powder from freshly ground beans or pre-ground va-
cuum-packed coffee. Never fill the funnel with more than
2 portions of coffee powder at a time. The powder funnel
is not intended as a storage container.
Ⅲ Put a cup under the pivoting nozzle (20).
Ⅲ Immerse the frothing nozzle (21) into the milk you want to froth
or into the liquid you want to heat up. Turn selector switch for
coffee or hot water / steam (19) to the symbol
If selector key
is pressed by mistake this can be correc-
.
ted by pressing one of the coffee keys.
Ⅲ
STEAM INTAKE
Ⅲ To stop steam-function turn selector switch for coffee or hot wa-
ter / steam (19) back to the symbol
9. Drawing off hot water
.
Ⅲ Press selector key for hot water . Wait until the flashing of the
lamp turns into a constant light.
After drawing off steam immediately draw off approx. 1dl of
water and clean the outside of the nozzle with a cloth.
E
Ⅲ Put a cup under the pivoting nozzle and turn selector switch for
coffee or hot water / steam (19) to the symbol . The machine
will now deliver hot water.
If you want to draw off steam several times, the selector key
for steam can be left on. The drawing off of steam is on
stand-by-status. If you draw off steam only once, then the
Ⅲ
WATER SUPPLIED
Ⅲ To stop this process turn selector switch for hot water / steam
(19) back to the symbol . The cup should only be removed
selector switch for steam
the selector key anew.
should be turned off by pressing
When steam is first drawn off, there is a possibility of spat-
tering. The pivoting nozzle becomes hot. Avoid direct
contact with the skin.
when the hot water has stopped its flow.
The machine has a stand-by-status for hot water. If you want
to alternate between drawing off coffee and hot water, the
selector switch for hot water can be left turned on . If you
draw off hot water only once, then the selector switch for hot
water should be turned off by pressing the selector key
anew.
11. Switching off machine
When the machine is switched off, the rinsing program is auto-
matically run again. Therefore place an empty container under the
coffee-spout (15) and press ON/OFF key
. When the rinsing
When hot water is first drawn off, there is a possibility of
spattering. The pivoting nozzle becomes hot. Avoid direct
contact with the skin.
water has run into the container, the machine powers down.
Discard the water.
11
12. Programming
Ⅲ
POWDER QUANTITY / SELECT KEY.
+
Ⅲ You can go to the next setting by pressing key
.
Before leaving our factory, the machine is adjusted to enable you
to obtain coffee without any additional programming. In order to
adapt the result to your personal taste, various settings can be pro-
grammed individually. The programming keys are located behind
the front cover (3).
12.2 Programming coffee temperature
Ⅲ
TEMPERATURE COFFEE / SELECT KEY
Ⅲ Now press the key that you want to programme.
Ⅲ Select the required temperature (high or normal) by activating
The following settings can be programmed:
+
key
or - .
̈ Powder quantity
̈ Brewing temperature
̈ Water quantity
Ⅲ To store the new coffee temperature in memory briefly press
P
key
.
̈ Filter
Ⅲ
TEMPERATURE COFFEE / SELECT KEY
̈ Water hardness
+
Ⅲ You can call up the next setting by pressing key
.
̈ Economy mode
̈ Timer clock
12.3 Programming water quantity
̈ Automatic switch on time
̈ Automatic switch off time
̈ Supplies and cup counter
̈ Language selection
Ⅲ
WATER QUANTITY / SELECT KEY
Ⅲ Put a cup under the coffee-spout (15) and then press the key that
you want to programme.
Ⅲ
The selected value is confirmed
12.1 Programming POWDER QUANTITY
Ⅲ Now your machine prepares a coffee.
Ⅲ Switch the machine on by pressing ON/OFF key
.
P
Ⅲ
Ⅲ
ENOUGH COFFEE / PRESS KEY
P
Ⅲ Press key
until you can hear an acoustic signal.
P
–
+
··········II··········
OK?
Ⅲ
POWDER QUANTITY / SELECT KEY
P
Ⅲ When the required water quantity is reached press key
. You
Ⅲ Now press the key that you want to programme. Use the key for
1 cup only. The corresponding quantity for 2 cups is adjusted
automatically by the machine after programming is finished.
+
can call up the next setting by pressing key
.
Ⅲ There is an additional possibility to alter the water quantity
+
anew. Press key
or - for this purpose.
Ⅲ
POWDER
Ⅲ If you wish to draw another coffee to control the water quantity,
–
+
··········II··········
P
press key again otherwise press key
quantity in memory.
briefly to store water
+
Ⅲ The powder quantity can be selected by pressing keys
briefly.
or -
+
Ⅲ You can call up the next setting by pressing key
.
Ⅲ To store the new powder quantity in memory briefly press
P
key
.
12
12.4 Programming FILTER
After 10 minutes the steam heating-system switches off
automatically. The warning lamps go out. By pressing the
steam key anew, you return to stand-by-status for drawing
off steam.
Please read chapter 7.1 “Placing filter”.
12.5 Programming WATER HARDNESS
(only with setting FILTER NO)
ECONOMY MODE OFF means that the stand-by-status for
steam is set to 10 minutes and the heating for the cup warm-
ing tray is on. After 10 minutes the heating-system switches
down to a stand-by temperature. By pressing the steam key
anew, the machine returns to stand-by-status for drawing off
steam.
Ⅲ
HARDNESS LEVEL 3
P
Ⅲ Press key
+
-
Ⅲ By pressing key
hardness level.
or
briefly you can programme the water
P
Ⅲ Then press key
memory.
briefly to store the water hardness level in
12.7 Programming TIMER CLOCK
A programming of the timer clock is necessary if an automa-
tic switch on time is required.
+
Ⅲ You can call up the next setting by pressing key
.
Ⅲ
TIME –.–
To determine the water hardness level please read chapter 6.
“Adjusting for water hardness”.
P
Ⅲ Press key
.
+
Ⅲ By briefly pressing key
confirm by pressing key
or - you can set the hours and then
E
12.6 Programming ECONOMY MODE
P
.
+
Ⅲ By briefly pressing key
or - you can set the minutes and
Ⅲ
ECONOMY MODE OFF
P
then confirm by pressing key
.
P
Ⅲ Press key
+
Ⅲ You can call up the next setting by pressing key
.
Ⅲ
ECONOMY (MODE OFF flashes)
+
-
Ⅲ By briefly pressing key
you would like.
or
you can programme the mode
12.8 Programming automatic switch on time
A programming of the timer clock is necessary if an auto-
matic switch on is needed.
P
Ⅲ Then press key
briefly to store mode in memory
+
Ⅲ You can call up the next setting by pressing key
.
Ⅲ
UNIT ON –.–
You can programme your machine to “economy mode”. In
the setting ECONOMY MODE ON the steam heating-
system is switched off. The heating for the cup warming tray
is switched off too. If you want to draw off steam you need
P
Ⅲ Press key
.
+
P
Ⅲ By briefly pressing key
confirm by pressing key
or - you can set the hours and then
.
to press the steam key
machine heats up.
, warning lamps flash and your
+
-
.
Ⅲ By briefly pressing key
then confirm by pressing key
or
you can set the minutes and
P
+
Ⅲ You can call up the next setting by pressing key
.
13
To switch off the automatic timer proceed as follows:
Ⅲ
COFFEE READY
P
Press key
N
Ⅲ Press key
until you can hear an acoustic signal.
N
Press key
UNIT ON —:—
If a mistake occurs while programming one of the above
N
settings, just press key
and the chosen setting moves back
12.9 Programming automatic switch off time
to its original standard setting.
Ⅲ
OFF AFTER 5.0 HOURS
13. Care and maintenance
13.1 Fill water
P
Ⅲ Press key
+
P
-
Ⅲ By briefly pressing key
or
you can set the hours and then
confirm by pressing key
(0.5 to 9.0 hours).
Ⅲ
FILL WATER
+
Ⅲ You can call up the next setting by pressing key
.
Ⅲ If this message shows on the display no more coffee can be
drawn off. Top up water.
12.10 Cup counter
The water tank should be rinsed and filled with fresh water
daily. Only use fresh, cold water. Never top up with milk,
mineral water or any other liquids. You can top up water
without removing tank.
Ⅲ
200 SUPPLIED (TOTAL SUPPLIED)
Ⅲ To obtain the information press the required key. The display
will show you the number of times the function has been chosen.
+
Ⅲ You can call up the next setting by pressing key
.
13.2 Empty grounds container
It is not possible to call up hot water and steam supplies.
Coffee grounds are collected in the grounds container.
Ⅲ
EMPTY GROUNDS
12.11 Programming language selection
Ⅲ If this message shows on the display no more coffee can be
drawn off. It is necessary to empty the grounds container.
P
Ⅲ Press key
Ⅲ Remove drip tray carefully as there is water in it.
+
-
Ⅲ By briefly pressing key
and then confirm by pressing key
or
call up the language desired
P
.
Do not disconnect the machine from power socket while
you empty grounds.
N
Ⅲ By pressing key
you can leave the programming modus or
+
you can call up the next setting by pressing key
.
13.3 Empty drip tray
N
12.12 Program key
Ⅲ
EMPTY TRAY
N
By using key
you can set back the following settings (powder
Ⅲ If this message shows on the display no more coffee can be
quantity, coffee temperature, water quantity) to their original stan-
dard settings.
drawn off. It is necessary to empty the drip tray.
Ⅲ Remove drip tray carefully as there is water in it.
14
13.4 Fill beans
13.7 Unit calcified
Ⅲ
FILL BEANS
Ⅲ
UNIT CALCED
Ⅲ Fill in beans as described in chapter 3.3.
The machine signals when decalcifying becomes necessary.
The message FILL BEANS will only disappear after drawing
off a coffee. We recommend cleaning the bean container
from time to time with a dry cloth before you refill beans.
Switch off the machine for this purpose.
Under the correct implementation of Claris filter cartridges,
decalcifying of the machine becomes unnecessary. For fur-
ther indications read Chapter 7 “Use of Claris filter cartrid-
ges”.
13.5 Removing foreign objects
13.8 Cleaning metal contacts
Ⅲ Switch off your machine by pressing ON/OFF
key.
Ⅲ
EMPTY TRAY
Ⅲ Remove plug from power socket.
To switch off this message you need to remove calcified deposits
from the metal contacts. Proceed as follows:
Ⅲ Open bean container (13) and remove the beans. The remaining
beans can be removed with a vacuum cleaner.
Ⅲ Rinse fastenings in groove (B) (Fig. 8) as well as the metal con-
tacts (A) with hot water and some washing-up liquid. Then clean
the fastenings in groove (B) as well as metal contacts with a
brush.
Ⅲ Loosen both screws in the bean container and then remove con-
tainer (Fig. 5+6)
Ⅲ Remove any remaining beans with a vacuum cleaner.
Ⅲ Put the spanner on (Fig. 7).
E
Ⅲ Now turn spanner anticlockwise until the foreign object loosens.
Ⅲ Remove remaining powder with a vacuum cleaner.
Ⅲ Replace bean container and fasten screws.
13.9 General cleaning instructions
Ⅲ Never use abrasive articles or corrosive chemicals to clean your
machine.
Ⅲ Wipe down the casing inside and out using a soft damp cloth.
13.6
Clean machine
Ⅲ Clean the pivoting hot water / steam nozzle after every use.
Ⅲ
CLEAN UNIT
Ⅲ After warming milk, draw off some hot water to clean the pivo-
ting nozzle inside.
After coffee, etc., has been drawn off 220 times or after 180 rinsing
programs have been run, the machine must be cleaned. You can
continue to draw off coffee and hot water / steam. However we re-
commend that you clean the machine (as described in chapter 14)
within the next few days.
Ⅲ You can take off the pivoting nozzle for a thorough cleaning
Ⅲ The water tank should be rinsed and filled with clean water
daily.
Ⅲ
CLEAN NOW
If you notice any furring in the water tank, this can be
decalcified separately with a customary decalcifying agent.
Remove the tank from the machine for this purpose.
An acoustic signal indicates the need of an immediate cleaning.
15
15. Decalcifying
If a Claris filter cartridge is used, remove it beforehand.
Your machine has an integrated decalcifying program (duration
approx. 35 min.).
Please use Jura decalcifying tablets only. These are available from
your Jura dealer.
13.10 Regular servicing
Regular Jura services ensure your machine’s reliability and longer
life. Keep the original packaging to protect the machine while
being transported.
Run the decalcifying program only after the machine has
been switched off for at least 5 hours and has cooled down
completely. The running decalcifying program must not be
interrupted.
14. Cleaning
The machine has an integrated cleaning program. The procedure
lasts about 15 minutes. Please use Jura cleaning tablets only. These
are available from your Jura dealer.
If using acidic decalcifying agents be sure to immediately
remove any splashes and drops from delicate surfaces,
especially natural stone and wooden surfaces, or take cor-
responding precautions.
It is essential not to interrupt the process once it has been started.
In any case please wait until the filled decalcifying agent is
used up and the tank is empty. Never top up the decalcifying
agent.
Ⅲ Switch on machine by pressing
key.
Ⅲ Press key
until you can hear an acoustic signal.
Ⅲ
EMPTY TRAY (FILL WATER might show as well)
Put a sufficiently large container under the coffee-spout (15)
in order to prevent cleaning liquid from running into the drip
tray.
15.1 Decalcifying coffee sector
Ⅲ Remove and empty water tank.
Ⅲ Replace empty water tank.
Ⅲ
Ⅲ
Ⅲ
Ⅲ
Ⅲ
ADD TABLET (Fig. 9) / PRESS CLEANING
UNIT CLEANING
Ⅲ Switch off your machine by pressing ON/OFF
Ⅲ Open cover (3).
key.
EMPTY TRAY
Ⅲ Press key until you can hear an acoustic signal.
RINSE UNIT
Ⅲ
Ⅲ
EMPTY TRAY
COFFEE READY
AGENT IN TANK
Pour 0.6 litres of water into a container and completely
dissolve the contents of a blister pack (2 tablets). Then fill
the mixture into the water tank.
The powder funnel for pre-ground coffee should be cleaned
after each cleaning process. Remove it from the machine ,
rinse it with hot tap water and replace it after drying.
Ⅲ
CHOOSE SECTOR / AGENT IN TANK /
PRESS CALC
Ⅲ Turn selector switch for coffee to the symbol
Ⅲ Press key
.
.
16
Ⅲ
COFFEE SECTOR / UNIT DECALCIFYING
Ⅲ
AGENT IN TANK / CHOOSE SECTOR /
PRESS CALC
Ⅲ Inside the machine the decalcifying agent is conducted to the
drip tray.
Ⅲ Place a container under the pivoting nozzle and turn selector
switch for coffee or hot water/steam (19) to the symbol
.
Ⅲ
Ⅲ
Ⅲ
Ⅲ
EMPTY TRAY
Ⅲ Press key
.
FILL WATER
Ⅲ
Ⅲ
UNIT DECALCIFIYING / WATER SECTOR
PRESS CALC
FILL WATER
COFFEE SECTOR / UNIT DECALCIFIYING
Rinse water tank well and top it up with fresh tap water.
Ⅲ Inside the machine the water is conducted to the drip tray.
Ⅲ
Ⅲ
Ⅲ
Ⅲ
Ⅲ
Ⅲ
PRESS CALC
Ⅲ
EMPTY TRAY / CLEAN CONTACTS
(please refer to chapter 13.8)
WATER SECTOR / UNIT DECALCIFYING
CLOSE TAP
Ⅲ
Ⅲ
PLEASE WAIT
RINSE UNIT
RINSE UNIT
UNIT RINSING
Ⅲ Place a container under the coffee-spout (15) and press rinsing
key
.
COFFEE READY
Ⅲ
Ⅲ
UNIT RINSING
16. Disposal
COFFEE READY
E
For correct disposal, you should return your coffee machine to your
dealer, Jura service centre or Jura Elektroapparate AG.
15.2 Decalcifying water sector
This message will only appear if the unit is ready to draw off water
or steam.
17. Tips for a perfect coffee
Ⅲ Remove and empty water tank.
Height adjustable coffee-spout
You can adjust the height of the coffee-spout to your cup sizes.
Ⅲ Replace empty water tank.
Grinding
Ⅲ Switch off your machine by pressing ON / OFF
Ⅲ Open cover (3).
key.
Please refer to chapter 3.4 “Adjusting grinder”.
Pre-warm cups
Ⅲ Press key until you can hear an acoustic signal.
You should warm cups in advance with hot water or steam. The
smaller the quantity of coffee, the more important warming the
cups is.
Ⅲ
Ⅲ
EMPTY TRAY
AGENT IN TANK
Pour 0.6 litres of water into a container and completely dis-
solve the contents of a blister pack (2 tablets). Then fill the
mixture into the water tank.
Sugar and cream
Warmth is lost by stirring the contents of the cup. Adding milk or
cream from the refrigerator considerably lowers the temperature of
the coffee.
17
18. Messages
Cause
Action
FILL WATER
Water tank is empty
Top up with water
Water level indicator in tank is jammed
Tank is calcified, water level indicator is stuck
Empty tank, rinse out, fill up and replace
Remove tank, decalcify, rinse well, fill up with
water and replace
FILL BEANS
Bean container is empty
Top up with beans
Message still displayed, although beans filled
Draw off cup of coffee. FILL BEANS message
only disappears after coffee is drawn off
A foreign object is stuck in the grinder
Coffee grounds container is full
Remove foreign object as described in chapter
13.5 “Removing foreign objects”
EMPTY GROUNDS
Remove drip tray, empty grounds container,
replace tray
Message still displayed, although grounds
container emptied.
The tray was out of the machine for less than
8 sec for emptying. Take tray out again for
approx. 10 sec and replace
The message appears after only a few cups
have been drawn off
Leave the machine switched on while
the grounds container is being emptied. The
counter is only reset to zero if the machine is left
switched on
TRAY MISSING
EMPTY TRAY
Tray has not been replaced correctly
Insert tray correctly
Grounds have fallen under tray and are preventing
it from being correctly inserted
Remove tray, clean inside
of machine, replace tray
The residual water container is full
Remove container carefully, empty, rinse out
and replace
Message still displayed, although container emptied
Remove container, clean metal contacts
(please refer to chapter 13.8)
18
Cause
Action
CLEAN UNIT
You have drawn off coffee 220 times or run
the rinsing program 180 times
Clean as described in chapter 14
Message still displayed, although machine cleaned
Run cleaning program again; this time do
not add cleaning tablet
UNIT CALCED
COFFEE SECTOR
WATER SECTOR
The appropriate sector needs decalcifying
Run decalcifying program as described
in chapter 15
Message still displayed, although machine decalcified
Run cleaning program again; this time using
water only and without decalcifying agent
CLOSE TAP
FAULT
Not ready to provide water or steam
Various causes
Switch over to coffee sector, press water or
steam key and then draw off the water or steam
required
Ring the hotline
E
19. Problems
Problem
Cause
Action
Coffee only flows in dribs
and drabs while drawing off
– Powder too fine
– Adjust grinder to a coarser grinding
– Run one or two rinse programs
– If result is no better, clean the machine
– as per instruction
Coffee flow is stopped
after pre-brewing
– Not enough coffee powder in the system
– Foreign element in grinder
– Draw off one cup of coffee
Grinder is extremely noisy
– Proceed as described in chapter 13.5
19
Problem
Cause
Action
Not enough froth while
frothing up milk
– Unsuitable milk-type
– Use full cream milk
– Clean frothing nozzle
– Draw off steam
– Frothing nozzle blocked
– Frothing nozzle in wrong position
If the above mentioned problems and/or messages still persist, please contact your dealer
or get in touch directly with Jura Elektroapparate AG.
20. Legal information
21. Technical specifications
These operating instructions contain all the information necessary
for the correct use, operation and maintenance of your espresso/
coffee machine.
Understanding and complying with the directions contained in
these operating instructions are essential to ensure that the machine
is utilised without risk and to ensure safety during operation and
maintenance.
These operating instructions cannot cover all the possible ways in
which this machine may be used. This machine has been designed
for private use in households.
We would like to further point out that the contents of these opera-
ting instructions in no way constitute a part of, or alter, any pre-
vious or existing contract, agreement or legal relationship. All ob-
ligations on the part of Jura Elektroapparate AG result solely from
the relevant sales agreement which also contains full details of the
only warranty terms valid in respect of this machine. The contrac-
tual terms of this warranty are neither extended nor limited in any
form by the information in these operating instructions.
These operating instructions contain information that is protected
by copyright. The photocopying or translation into any other lan-
guage of these instructions without prior written authorisation from
Jura Elektroapparate AG is strictly prohibited.
Impressa S70
Voltage:
Power consumption:
Fuse:
230 V AC
1350 W
10 A
Safety measures exam:
Energy consumption standby:
Energy consumption ready to make
coffee:
approx. 4,4
approx. 31 Wh, Economy Mode on
approx. 41 Wh, Economy Mode off
max. 15 bar
2,7 litres
280 gr.
max. 16 port.
approx. 1,1 m
11,7 kg
34,5 x 35 x 39 cm
Pump pressure:
Water tank:
Capacity, bean container:
Capacity, grounds container:
Cable length:
Weight:
Dimensions (BxHxD):
Impressa X70
Water tank:
Capacity, grounds container:
Weight:
5,7 litres
max. 40 port.
15 kg
Dimensions (BxHxD):
41 x 47 x 39 cm
20
|