© 2010 GN Netcom A/S. All Rights Reserved.
This user guide is published by GN Netcom A/S.
Thank you
Thank you for purchasing the Jabra LINK™ 280 controller. We hope you enjoy it! This instruction manual will get
you started and ready to make the most of your controller.
The information in this user guide is furnished for informational use only, is subject to change without notice,
and should not be construed as a commitment by GN Netcom A/S. GN Netcom A/S assumes no responsibility or
liability for any errors or inaccuracies that may appear in this user guide.
abouT your Jabra LInk 280 conTroLLer
1
2
3
4
5
6
7
QD Plug
USB plug
Mute button
Soft button (×)
Soft button (O)
Hookswitch
Volume control
5
2
7
1
3
6
4
2
3
how To adJusT voLume on The conTroLLer
Use the wheel at the center of the
controller to adjust the volume.
Turn clockwise to turn up and
counterclockwise to turn down. You will
hear a soft click in the headset each time
you adjust the volume.
When you reach maximum volume, the
headset will beep twice as a warning.
We recommend that you do not use the
headset at full volume.
how To connecT conTroLLer To headseT
Plug the QD to the QD of any Jabra GN corded headset.
how To muTe The headseT
It is possible to mute the microphone on the headset so that no sound/voice will be transmitted from the
headset to the PC.
By tapping the mute button the microphone is now muted. The lights will go from a solid green to pulsating red.
It will continue to pulsate red while muted.
To un-mute: tap
the mute button
again and the
light will go from
pulsating red to
solid green.
Green when not muted
Red when muted
how To connecT conTroLLer To Pc
Plug the USB plug into a free USB port on your PC. Once connected, the active mute and hookswitch buttons will
be illuminated.
how To answer a caLL from your Pc sofTPhone
The first time connected, your PC displays a small pop-up message in the task bar to indicate that a new device
has been found. You are now ready to use the controller.
When a softphone call arrives, you will hear a ring tone in the headset.
If you are using a Jabra-supported softphone*, then answer by tapping on the hook-switch button on the USB
controller; tap again to hang up when you are done. Softphone control requires that you install Jabra PC Suite
(described later in this manual).
For other softphones, use the native interface on your computer to answer and hang up.
When you are using a
supported softphone,
the controller lights
work as indicated to
the right.
Solid green while idle
You also have the
option of rejecting
an incoming call by
pressing and holding
the assigned Soft
button. The incoming
call will then be
Flashing green/
blue on incoming
call
Red while on a call
rejected.
4
5
Jabra Pc suITe Programs
After installing the software, you will have an All Programs > Jabra > Jabra PC Suite folder in your Windows Start
menu. It provides links to the following programs:
how To acTIvaTe oPTIonaL feaTures
how To use The sofT buTTons.
The controller includes two soft buttons, labeled × and o, respectively. You are able to program the controller
to use these two buttons for any of several functions. For example, you can configure one of the soft buttons to
control the Bluetooth connection to a mobile phone.
-
-
-
Jabra Control Center
Enables you to configure your controller from your PC.
Jabra Device Firmware Updater
Enables you to update the controller firmware.
Jabra Devices Service
Runs in the background and monitors your USB ports for Jabra devices. It makes sure that Windows will
recognize these devices and enables the Jabra Control Center and Softphone drivers to interact with them.
In addition to the above programs, the PC Suite also provides drivers for several types of softphones, including
Skype, Cisco IP Communicator and Microsoft® Lync™ 2010.
When you are using a supported softphone, you will be able to control that softphone using the buttons of the
controller. You can also talk using any softphone using its native graphic interface on your computer.
Note: Jabra is constantly evaluating the softphone market to see which new programs should be
supported with a dedicated driver. Contact your Jabra representative or see the Jabra web site for the
latest news on softphone driver development.
See the section about using Jabra PC Suite below for details.
usIng Jabra conTroL cenTer wITh The Jabra LInk 280 conTroLLer
how To InsTaLL and use The Jabra Pc suITe
The Jabra PC Suite is a collection of programs that support and expand your controller’s features. It is available as
Jabra Control Center is the Jabra Control Suite program that enables you to configure your controller. To run
the program, click on the Windows Start menu and select All Programs > Jabra > Jabra PC Suite > Jabra Control
Center.
Jabra PC Suite enables you to:
-
-
-
-
Control several types of softphone programs from your controller via dedicated softphone drivers.
Assign function to the programmable × and O buttons of the USB controller.
Set the hearing-protection level for the headset.
Update the firmware for the controller.
InsTaLLIng The Jabra Pc suITe
To install the Jabra PC Suite, do the following:
1. If you have not already installed your softphone, then we highly recommend that you do so before you install
Jabra PC Suite. This will ensure that Jabra support is correctly added to your softphone program. If you add
a new softphone program to your computer after installing Jabra PC Suite, then we recommend that you
reinstall Jabra, which is quite easy.
3. Run the setup.exe program included with the download. This will install Jabra PC Suite on your computer.
4. Follow the instructions on your computer screen. Installation is very simple and should take just a minute or
so. Please note the following as you work through the installation wizard:
When the controller is connected to your computer, you will see the settings that are relevant for that controller.
These settings are divided into three tabs: Softbuttons, Settings, and Mobile (only when activated). Each of these
is described below.
-
-
-
-
Jabra PC Suite requires Microsoft .NET Runtime 3.5. If this is not already installed on your PC, then the setup
program will automatically download and help you install it (requires an Internet connection).
The wizard will ask which components of the Jabra PC Suite you would like to install. Usually, you should
install all of them.
If you are using Microsoft Windows Vista, you may see a “user account control” message; just click on “Allow”
to continue with the installation.
The wizard will ask if you would like to start the Jabra Device Service when Windows starts (see also the
descriptions of these programs below). If you will often use your controller with a softphone, then we
recommend that you enable the Device Service.
-
At one point, you may see a warning from Windows that the software “has not passed Windows Logo testing.”
This is expected and does not indicate a problem. You can safely click on the “Continue Anyway” button.
6
7
The Settings Tab
WARNING: Do not remove the controller from your PC while the firmware is being updated and make
sure your computer will not shut down or go into sleep or standby mode during the process. (Should
a disconnection unintentionally occur, please retry from step 1)
The options on the Settings tab enable you to control the Audio protection (Intellitone).
To apply a firmware update:
1. If you have not already done so, then attach your controller to your computer.
2. If you have not already done so, then download the firmware update from Jabra and save it on your hard disk
or network in a location where you can see it from your computer.
3. On your PC, use the Start menu to run the firmware-update application of the Jabra PC Suite.
4. Follow the instructions on your screen to identify your controller model, select the firmware update file and
apply it. See also the Jabra PC Suite online help for more details.
Use the settings in the Audio protection (Intellitone) area of the Settings tab to set the hearing-protection level
of your headset.
how To use The conTroLLer wITh a mobILe Phone
The controller includes a Bluetooth circuit, which enables the controller to connect directly wirelessly to a mobile
phone or another Bluetooth sound source. When connected to a mobile phone, you will be able to answer and
end calls using the buttons of the Jabra LINK 280 controller.
Hearing risk is evaluated as a function of both volume and duration. Therefore, the maximum sound level should
be lowered as the number of hours you spend using the headset increases. The controller offer a choice of four
protection levels. These features protect your hearing by preventing acoustic shocks and limiting the maximum
noise exposure from the headset during your workday. This system is called Intellitone™, which is only available
from Jabra. All protection levels (including “none”) also feature Peakstop™, which offers protection against
sudden, loud audio spikes.
Pairing the controller with Your Mobile Phone
All three Intellitone levels above (other than “none”) meet and exceed de facto global protection levels, and are
compliant with NIOSH standards and EU health and safety codes of 85 dB(A).
To use your controller with a mobile phone, you must pair the controller with your phone. Once they are paired,
the controller will automatically connect to the mobile phone whenever it is in range (i.e., you should only need
to pair the two devices once). The controller must remain connected to your computer, because it requires
power from the USB connection.
In the Audio protection (Intellitone) area, mark the radio button for the Intellitone level that matches the number
of hours in which you use the headset each day.
If you are using a Lync 2010 softphone you need to switch to Lync 2010 in the Settings tab as the primary target
softphone for your calls.
To pair your controller with a mobile phone:
1
Connect your controller to your computer and run the Jabra Control Center (see above).
Important: Check your local laws or regulations to find out whether a specific protection level is mandated in
your area.
2. Go to the Softbuttons tab of the Jabra Control Center. Here you see two drop-down lists for assigning
functions to each of the soft buttons of the controller.
The Softbutton Tab
The settings on the Configuration tab enable you to assign functions to the soft buttons of the controller
(labeled × and O, respectively).
3. Decide which of the two soft buttons you would like to use to control your mobile phone. Open the matching
drop-down list and select Mobile from the list.
4. The controller now lights blue, which indicates that the controller is in pairing mode. This means that it is
advertising itself for pairing with other Bluetooth devices.
5. Make sure that Bluetooth is active on your mobile phone and put your phone into Bluetooth finding mode.
The exact procedure for doing this varies by mobile phone manufacturer and model — see your mobile
phone manual for details.
Use the drop-down lists here to select from the available functions for each of the two soft buttons. Once
configured, you will be able to trigger these functions by pressing the corresponding button on the controller.
6. Your phone now looks to see if any nearby Bluetooth devices are advertising themselves for pairing — this
should include your controller. Use your phone’s controls to identify and select the “Jabra LINK 280” device.
Your phone may also ask for the controller’s pass code. The pass code for all Jabra devices is 0000 (four zeros);
if necessary, enter this code into your phone and commit the code (e.g., by pressing on an OK button).
Often, you will configure these buttons to control the Bluetooth connection to your mobile phone. *See “Pairing
the controller with Your Mobile Phone”, below, for details about how to do this.
If you want stereo sound for playing music, your phone needs to support A2DP.
7. Your phone will now attempt to connect to the Jabra LINK 280 controller and then shows you the result of the
attempt. If the attempt fails, please try again. If you are still having trouble, please check your mobile phone
documentation and/or contact technical support for Jabra and/or your mobile phone.
Updating the controller Firmware
Firmware updates can sometimes improve the performance of your controller and/or add new features. Visit
the Jabra web site to find out if firmware updates are available for any of your Jabra products. You will be able to
download the updates from there as they become available.
8
9
*check you mobile manual for instruction on how to pair to controller.
need more heLP?
European customer service information:
Phone:
E-mail:
Belgique/Belgium + 49 (0)8031 2651 72
Czech Republic
Danmark
Deutschland
España
+ 420 800 522 722
+ 49 (0)8031 2651 72
+ 34 916 398 064
France
Italia
+ 33 (0) 130 589 075
+ 39 02 5832 8253
+ 49 (0)8031 2651 72
+ 49 (0)8031 2651 72
+ 47 32 22 74 70
+ 49 (0)8031 2651 72
+ 48 12 254 40 15
0 801 800 550
Once you have selected the mobile as one of the functions for your softbuttons, a Mobile tab will appear in the
Jabra Control Center.
You will be able to clear your paring list, thereby deleting the mobile phones paired to the controller. Once you
have clicked Clear pairing list — the controller will automatically enter a pairing mode.
Luxembourg
Nederland
Norge
Österreich
Poland
By clicking on Enter pairing mode, the controller will enter pairing mode and you are now able to pair the
controller to a mobile phone — see the section on pairing your controller to a mobile phone, above.
Answering an Incoming Mobile Call
support.fi@gn.com
When a call arrives at your mobile phone, you will hear a ring tone in the headset and the controller will flash
blue and green. To answer the call, tap the soft button that you assigned to the mobile phone. When you are
done talking, tap the same button again to hang up.
Russia
Suomi
Sverige
+ 358 204 85 6040
+ 46 (0)8 693 09 00
United Kingdom + 44 (0)1784 220 172
Placing a Call over Your Mobile
To place a call with your mobile phone while using your controller, simply dial your mobile phone as usual.
Usually, the audio will be sent to your headset automatically whenever it is in range of your mobile phone.
USA and Canada warranty
Web:
Please see your mobile phone manual for details about how your specific mobile phone interacts with a Bluetooth
device and which, if any, configuration settings are available for this feature.
E-mail:
Phone:
Technical support: [email protected] Information: [email protected]
Canada
USA
1-800-489-4199
1-800-826-4656
TroubLeshooTIng & faQs
Q: I have pairing problems?
A: Make sure that the controller is in paring mode, indicated by a solid blue light. See the instructions in the user
manual of that particular mobile to make sure that the mobile is also in paring mode.
Asia Pacific customer contact information
E-mail Information: [email protected]
Phone:
Q: I cannot hear anything in my headset?
A: Make sure that the controller is selected as audio device on both the computer in the Control Panel and in the
application you are using.
Australia
China
1-800-636-086 (local distributor)
+ 86-21-5836 5067
Q: My computer does not detect the controller?
A: Try to insert the controller in another USB port.
Hong Kong
India
800-968-265 (Toll free)
000-800-852-1185(Tollfree)
001-803-852-7664
Q: The computer does not automatically assign the headset as the default audio device?
A: You can always select the headset as your default audio device manually.
Indonesia
Japan
-
-
Go to the Control Panel on your computer.
+ 81-3-5297-7976
Open the menu Sound and Audio devices. When inserted you can select the headset (It should appear as
Jabra Link 280) as your default device for Sound playback and Recording.
Malaysia
New Zealand
Philippine
Singapore
Taiwan
1800-812-160 (Tollfree)
0800-447-982 (Toll free)
+ 63-2-2424806
-
Press Apply and then press OK.
If you are using Macintosh — Go to System preferences on your computer. When inserted you can select the
headset in the Sound menu under Output and Input.
800-860-0019 (Toll free)
0080-186-3013 (Toll free)
10
11
cerTIfIcaTIon and safeTy aPProvaLs
CE
gLossary
Bluetooth
This product is CE marked according to the provisions of the R & TTE Directive (99/5/EC). Hereby, GN, declares
that this product is in compliance with the essential requirements and other relevant provisions of Directive
to be used in Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece,
Hungary, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden,
The Netherlands, United Kingdom, and within EFTA in Iceland, Norway and Switzerland.
A radio technology that connects devices, such as mobile phones and headsets, without wires or cords over
Pairing
Creates a unique and encrypted link between two Bluetooth devices and enables them to communicate with
each other. Bluetooth devices will not communicate if they have not been paired.
Jabra PC Suite
A GN Netcom software communication control center.
FCC
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
DFU
Device Firmware Update
Firmware
Users are not permitted to make changes or modify the device in any way. Changes or modifications not
expressly approved by Jabra will void the user’s authority to operate the equipment.
The software that is embedded in a hardware device, for example the Jabra LINK 280 controller. Like software,
firmware is a computer program, which is executed by a computer.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
IP telephony
(Voice over Internet Protocol) The routing of internet voice conversations or through other IP-based networks.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-
-
-
-
-
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
The user must place the base 8” (20cm) or more from any personnel in order to comply with FCC RF exposure
requirements.
Industry Canada
Operation is subject to the following two conditions: (1) This device may not cause interference and (2) This
device must accept any interference, including interference that may cause undesired operation of the device.
The term “IC:” before the certification/registration number only signifies that registration was performed based
on a Declaration of Conformity indicating that Industry Canada technical specifications were met. It does not
imply that Industry Canada approved the equipment.
Bluetooth
The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Jabra is
under license. Other trademarks and trade names are those of their respective owners.
12
13
|