Wireless Weather
Projection Clock
with Light Detector
USER MANUAL
(PCR325W)
A LCD DISPLAY
Allows easy reading of indoor/ outdoor temperature,
weather conditions, and calendar and time.
E / I
O
B CHANNEL SELECTOR
LIGHT
SNOOZE
Selects different remote sensor readings.
LIGHT
SENSOR
C ALARM ON/OFF BUTTON
* Switches between the calendar display and three different
alarm modes.
A
T
O
M
I
C
C
L
O
C
K
* Sets the weekday alarm, single alarm or pre-alarm.
CH
A
C
D MODE BUTTON
M
D
* Toggles between the clock modes – the time with the
seconds and the time with the day of week.
* Sets the clock manually.
PM
N
M
E LIGHT/SNOOZE BUTTON
channel
alarm
mode
on/ off
Activates the snooze feature, backlight and projection.
F
G
D
B
F DOWN ( – ) BUTTON
Decreases the setting.
G UP ( + ) BUTTON
J
Increases the setting.
SIZE AA / UM3
H
H BATTERY COMPARTMENT
SIZE AA / UM3
Holds two “AA” batteries.
K
L
I
[LIGHT/SNOOZE]
Activates the projection for 5 seconds.
J
[ROTATE]
Rotates the projection image.
K [FLIP]
Flips the projected image180°.
L [FOCUS]
Adjusts the sharpness of the projected image.
M [CONTINUOUS PROJECTION]
Sets a continuous time and temperature projection.
4
3
N [LIGHT SENSOR] SWITCH
A LED INDICATOR
When AC adapter is connected, position the light sensor
switch to:
Flashes once when the remote sensor transmits a reading to
the main unit.
* “AUTO” to activate an auto backlight.
* “ON” to set continuous LCD backlight.
* “OFF” to deactivate LCD backlight.
The built-in light sensor detects the environmental light
conditions. If the light conditions are lower than 100 LUX,
the LCD lights up automatically.
Flashes twice when battery power is low.
B BATTERY COMPARTMENT
Holds two AA batteries.
C RESET
Resets all previous settings.
REMOTE SENSOR
FEATURES
D CHANNEL SELECTOR
Selects the desired channel before installing batteries.
•
Remote temperature transmission to the main unit via
433 MHz signal
E WALL-MOUNT RECESSED HOLE
Keeps the remote sensor on the wall.
•
•
•
•
•
Case can be wall mounted using built-in hanger
100 feet transmission range without interference
LCD display of measured temperature
Temperature display unit (C°or F°) selection
Transmission channel selection
F °C/ °F SWITCH
Selects the temperature display in Fahrenheit or Celsius.
BEFORE YOU BEGIN
1. We recommend using alkaline batteries for the main unit
and remote sensor.
E
2. Avoid using rechargeable batteries.
3. Insert batteries before first use, matching the polarity as
shown in the battery compartment.
1
MADE IN CHINA
A
F
D
4. Always install batteries in the remote sensor before the
main unit.
C
5. Press RESET after each battery change, using paper clip or
similar tool.
B
6. During an initial setup, place the main unit as close as
possible to the remote sensor.
TM
THERMO
–
SENSOR
7. After reception is established (remote temperature will
appear on the receiver’s display), position the remote sensor
and main unit within the effective transmission range of
100 feet.
NOTE:
1. Avoid setting the time and date on the main unit before the
outdoor temperature is displayed.
2. The effective operating range may be influenced by the
surrounding building materials and how the receiver and
transmitter are positioned.
6
5
3. Position the remote sensor so that is faces the main unit
(receiver), minimizing obstructions such as doors, walls,
and furniture.
If no signals are received from the remote sensor(s) within
2 minutes, dashes “
” will be displayed.
Press and hold DOWN button [ – ] for 2 seconds to activate
another signal search.
4. Though the remote sensors are weather-resistant, they
should be placed away from direct sunlight, rain or snow.
CHECKING REMOTE AND INDOOR TEMPERATURES
The indoor temperature is shown on the middle line of the main
unit display. The remote temperature is shown on the top line of
the display. The wave icon near the remote sensor reading
indicates that there is a good signal reception from the remote
unit. If there is no signal received from the remote unit for more
BATTERY INSTALLATION
REMOTE SENSOR
NOTE: Install the batteries; select the channel and type of
temperature (ºC/ºF) before you mount the sensor.
1. Remove the screws from the battery compartment with a
small Phillips screwdriver.
than 2 minutes, a dashes “
” will be displayed. Hold [ – ]
button for 2 seconds to enforce an immediate search.
2. Set the channel. The switch is located in the battery
compartment. Channel 1 is typically selected if
only 1 remote sensor is being used.
CONTINUOUS PROJECTION
3. If you are using more than one sensor, select a different
channel for each sensor.
4. Install two “AA” size alkaline batteries (not included)
matching to the polarities shown in the battery compartment.
5. Replace the battery compartment door and secure the screws.
6. Secure the remote sensor in the desired location.
BATTERY INSTALLATION
MAIN UNIT
1. Open the battery compartment door.
2. Install two AA batteries (not included) matching to the
polarities shown.
3. Replace the battery compartment door.
LOW BATTERY WARNING
A low-battery indicator [
] will appear on the indoor or
outdoor temperature reading line of the main unit warning that
the corresponding sensor’s batteries need replacement.
GETTING STARTED
Insert 2 AA batteries and connect the included AC adapter
(AC120V, 60Hz-DC5.0V, 100mA).
After batteries are installed, remote sensors will transmit a
temperature readings at 45 second intervals. The main unit
may take up to 2 minutes to receive the initial readings.
Upon successful reception, remote temperature will be
displayed. The main unit will automatically update readings
at 45-second intervals.
7
8
CURRENT TIME AND INDOOR/OUTDOOR
TEMPERATURE PROJECTION
READING THE KINETIC WAVE DISPLAY
The kinetic wave display shows the main unit (receiver) signal
reception strength.
PM
Searching for signal
Temperature signals
successfully received.
1. Press "FLIP" to rotate projection image 180° clockwise.
˚F
No signal.
M P
WWVB RADIO CONTROLLED TIME
The NIST (National Institute of Standards and Technology)
radio station is located in Ft. Collins Colorado. It transmits
an exact time signal continuously throughout the continental
United States at 60 KHz frequency. The Wireless Weather
Projection Clock with Light Detector can receive this WWVB
signal through its internal antenna from up to 2,000 miles away.
Due to the nature of the Earth’s ionosphere, reception can be
limited during the daylight hours. The radio controlled clock
will search for an alternate station that derives its signal from
the NIST Atomic clock in Boulder, Colorado.
2. Press and hold the "FLIP" button for 2 seconds to change
temperature information from outdoor to indoor.
PM
The WWVB tower icon on the main unit’s display will flash
indicating radio signal reception from the WWVB station.
If the tower icon is not fully lit, or if the time is not set
automatically, please consider the following:
3. Press and hold the “FLIP” button for 2 seconds again, and
the display will switch between indoor and outdoor
temperatures every 5 seconds.
*
During night-time hours, atmospheric disturbances are
typically less severe and reception may improve.
A single daily reception is sufficient enough to keep
the accuracy reading within 1 second.
*
Make sure the main unit is positioned at 8 feet minimum
distance from any interference source such as a TV,
computer monitor, microwave, etc. The successful reception
of the atomic time signal depends on the positioning and
location of the clock. Always place the main unit by the
window for better reception.
9
10
*
Within concrete wall rooms such as basements or office
buildings, the received signal may be weakened.
Always place the unit near the window.
INDOOR ANR OUTDOOR TEMPERATURES
The trend indicator shows the trend of temperatures collected
at a particular remote sight. There are three trends will be
shown: rising, steady, and falling.
WEATHER FORECAST
TREND
TREND
TREND
The weather projection clock is capable to detect an
atmospheric pressure changes. Based on collected data,
it forecasts the weather for the next 12 to 24 hours.
Arrow
indicator
When the
display
shows...
Temperature
Trend
Rising
Steady
Falling
Partly
Sunny
Cloudy
Light Rain Heavy Rain
Forecast is...
MAXIMUM AND MINIMUM TEMPERATURE
The maximum and minimum record of the indoor and outdoor
temperature will be automatically stored in the memory. It will
display the minimum, maximum and the current reading upon
each press of both [channel] & [ – ] buttons, the unit will
return to the current temperature display in 15 seconds.
To clear the memory, press & hold [channel] for 3 seconds
and all stored readings will be erased.
Cloudy
NOTE:
1. The weather forecast accuracy is approximately 70%.
2. Display shows forecasted, not current conditions.
3. The “Sunny” icon indicates clear weather, even when
displayed during nighttime hours.
BAROMETRIC PRESSURE
The barometric pressure arrows indicate if pressure is
rising, steady, or falling.
LOST COMMUNICATION
If the main unit display for the remote sensor goes blank,
press and hold [ – ] for 2 seconds to begin a new signal
search. If the signal still isn’t received,
TREND
TREND
TREND
Arrow
please make sure that:
indicator
1. The remote sensor is in its proper location.
2. The distance between the main and remote units is not
over 100 feet.
Pressure
Trend
3. The path between units is clear of obstacles. Shorten the
distance between units if necessary.
Rising
Steady
Falling
4. Fresh batteries are installed correctly in both remote sensor
and main unit.
Note: When the temperature falls below freezing, the
batteries in outdoor remote sensor(s) may have reduced
voltage supply and a shorter effective range. We recommend to
Use lithium-ion batteries at the temperatures below 32°F
11
12
If everything listed above in order and there is no reception
anyway, please perform the following steps:
CALENDAR AND CLOCK DISPLAY MODES
The date is displayed in month-date format. Each press of the
MODE button will change the clock display setting between
the time with the seconds, and the time with the day of week.
1. Bring main unit and remote sensor close together.
2. Remove 4 small screws from the back of the remote sensor
and open the battery compartment.
3. Remove the batteries from the battery compartment and
reinstall them in the same manner. Remote sensor
LED indicator will flash showing transmission of the signal.
4. Remove the batteries from the main unit and reinstall them
in the same manner.
MANUAL SETTINGS
TIME ZONE
1. Press MODE to select the time with the day of week
display mode.
2. Select the time zone by pressing and holding the
“ + ” button for 3 seconds.
5. On the main unit select the same channel number as
set on the remote sensor. Remote temperature appeared on
the main unit’s display will show that transmission is being
received successfully.
3. Keep holding until the desired time zone (Pacific,
Mountain, Central or Eastern) is selected on the display map.
YEAR, DATE, TIME, TEMPERATURE UNIT
Press and hold MODE for 3 seconds: the year will flash.
Press “ + ” or “ - ” to change the flashing digits.
After the first value is set, press MODE again. Continue
setting month, day, hour, minute, display language,
Fahrenheit or Celsius display. When you’ve set the last value,
press MODE for the last time to return to regular mode.
TRANSMISSION COLLISION
Signals from other household devices, such as doorbells,
home security systems, and entry controls, may interfere
with this product and may cause temporary reception
failure. This is normal and will not affect the general
performance of the product. The transmission and reception
of temperature readings will resume once the interference
subsides.
ALARMS
* Weekday Alarm
The alarm will sound and the alarm icon will flash at the
set time Mondays through Fridays.
HOW TO SET THE RADIO CONTROLLED CLOCK
1. After the main unit receives temperature readings from
the remote sensor, the WWVB time signal receiver will
automatically search for the time signal. It takes
about 5-8 minutes. Always place clock by the window
for better reception.
* Single Day Alarm
The alarm will sound and the alarm icon will flash at the
set time, but will not activate on subsequent days.
2. If the radio signal is received, the date and time will be
* Pre-Alarm
set automatically, and the [
] icon will appear.
If the remote temperature is 32º F/0º C or below, the
pre-alarm feature will be activated. The pre-alarm time
interval can be set for 15, 30, 45, 60, 75 or 90 minutes before
the weekday or single alarm time. Press and hold
[ALARM ON/OFF] for 2 seconds in Pre-Alarm mode
to set the pre-alarm interval.
3. If after 8 minutes the time signal has not been received,
press the “MODE” button to set the time manually.
The clock will continue to search for the WWVB time
signal daily from 1:00 am to 4:30 am.
When the signal has been successfully received, the time
and date will be updated automatically.
13
14
“
” (Weekday alarm), “
” (Single day alarm), and
S
PRECAUTIONS
W
“Pre-AL” (Pre-alarm) icons will indicate which alarm mode
is armed. You can enable or disable an alarm by pressing the
[ + ],[ – ] buttons in alarm display mode. Press MODE to
toggle between alarm modes or to return to the default display.
This product is engineered to give you years of satisfactory
service if handled carefully. Here are a few precautions:
1. Do not immerse the units in water.
2. Do not clean the units with abrasive or corrosive materials.
They may scratch the plastic parts and corrode the
electronic circuits.
SETTING THE ALARM
3. Do not subject the product to excessive force, shock, dust,
temperature, or humidity, which may result in malfunctions,
shorter lifespan, damaged batteries, and damaged parts.
4. Do not tamper with the units' internal components. Doing
so will invalidate the warranty and may cause damage.
These units contain no user-serviceable parts.
To set any alarm,
1. Press [ALARM ON/OFF] once to display a specific alarm
time. If the selected alarm is off, “OFF” will be displayed.
2. Press and hold [ALARM ON/OFF] for 2 seconds.
The hour digit will flash.
3. Enter the hour using [ - ] or [ + ] buttons.
4. Press [ALARM ON/OFF] again. The minute digits will
flash.
5. Use only fresh batteries. Do not mix new and old batteries.
6. Read the user's manual thoroughly before operating the units.
5. Enter the minutes using [ - ] or [ + ] buttons.
6. Press [ALARM ON/OFF] again to exit from the alarm
time mode.
7. Repeat the same procedure to set any of alarms (weekly,
daily or pre-alarm).
SNOOZE
When the alarm sounds, press the LIGHT/ SNOOZE button
to temporarily stop the alarm. After depressing, the alarm
sound will resume in 5 minutes.
If the alarm is not disabled after that, it will sound for
4 more minutes and then will stop by itself.
HOW TO STOP AN ALARM
Press [ALARM ON/OFF ] on the main unit to disable any
alarm.
15
16
SPECIFICATIONS
Temperature Measurement
Main unit
Dimensions
Main unit
: 3.25(L) x 4.5(H) x 1.25(D) inches
Remote sensor : 2(L) x 4(H) x 1 (D) inch
Indoor Temperature
Proposed operating range
: -5°C to +50°C /
23°F to 122°F
: 0.1°C/ 0.2°F
FCC STATEMENT
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received,
including interference that may cause undesired operation.
Temperature resolution
Remote Sensor
Proposed operating range
with alkaline batteries
: -20°C to + 70°C /
-4 °F to 158°F
Warning: Changes or modification to this unit not expressly
approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
Proposed operating range
with lithium batteries
: - 38°F to 158°F
( -38.8 C° to 70°C)
: 0.1°C/ 0.2°F
Temperature resolution
NOTE: This equipment had been tested and found to comply
with the limits for a Class B Digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications.
RF Transmission Frequency
Maximum number of remote sensors
RF Transmission Range
: 433 MHz
: 3
: Maximum 100 feet
: approximately
45 seconds
Temperature sampling cycle
Calendar and Clock
12 hour display in hh : mm format
Date Format: Month – Day format
However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one
or more of the following measures:
Day of week: User- selectable in 3 languages
(English, French, Spanish)
Dual 4-minute crescendo alarm with snooze
Pre-alarm for ice alert with programmable time intervals
Power
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment to an outlet on a circuit different
from that to which the receiver is connected.
Consult the dealer or an experienced radio / TV technician
for help.
Main unit
: 2 x UM-3/ AA (1.5V) batteries
- alkaline are suggested (not included)
: AC adapter (AC120V, 60Hz-DC5.0V, 100mA).
Remote Sensor : 2 x UM-3/ AA (1.5V) batteries
- alkaline are suggested (not included)
Lithium batteries are suggested (not included)
at 32°F temperature and below
17
18
DECLARATION OF CONFORMITY
STANDARD WARRANTY INFORMATION
This product is warranted from the manufacturing defects for
one year from date of retail purchase. It does not cover
damages or wear resulting from accident, misuse, abuse,
commercial use, or unauthorized adjustment and repair.
We
Name: Hideki Electronics, Inc.
Address: 7865 SW Mohawk, Tualatin, OR 97062
Telephone No.: 1-503-612-8395
Note that online product registration is required to ensure
valid warranty protection.
declare that the product
To register your product, go to our Company website at:
under the Customer Service menu.
Product No.: PCR325W
Product Name: Wireless Weather Projection Clock with
Light Detector
Should you require assistance with this product and its
operation, please contact our
Manufacturer: Hideki Electronics Ltd.
Address: Unit 2304-06, 23/F Riley House, 88 Lei Muk Road,
Kwai Chung, New Territories, Hong Kong
Customer Service Hotline 1(866) 443 3543
Please direct all returns to the place of the original purchase.
Should this not be possible, contact Customer Service Hotline
for assistance and to obtain a Return Merchandise Authorization
(RMA). Returns without a return authorization will be refused.
Please retain your original receipt as you may be asked to
provide a copy for proof of purchase.
is in conformity with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
1. This device may not cause harmful interference.
This device must accept any interference received, including
interference that may cause undesired operation.
Hideki Electronics, Inc. reserves the right to repair or replace
the product at our option.
The information above is not to be used as contact for support
or sales. Please call our customer service hotline
Copyright (2005) Hideki Electronics Inc. All Rights Reserved.
The Honeywell Trademark is used under license from
Honeywell Intellectual Properties Inc.
(refer to the warranty statement) for all inquiries instead.
Honeywell International Inc. makes no representations or
warranties with respect to this product.
19
20
|