Accessory
Application
Publications No.
AII 23268
CD CHANGER
ATTACHMENT KIT
INSTALLATION
INSTRUCTIONS
INSIGHT
Issue Date
OCT 2001
PARTS LIST
CD Changer Attachment Kit:
P/N 08B26-S3Y-100
4 Clip nuts
2 Clips
CD changer trim
4 Self-tapping screws
4 Flange nuts
Front bracket
Bus cable
2 Spacers
Rear bracket
5 Long wire ties
(4 not used)
Front base bracket
CD Changer:
P/N 08A26-1B1-100
CD changer
Rear base bracket
6 EPT sealers
4 Washer-screws, 4 x 6
(Not used)
10 Cushion tapes
Adhesive seal sheet
Locking covers
13 Short wire ties
(1 not used)
8 Washer-screws, 4 x 8 mm
4 Washer-bolts, 6 x 16 mm
CD magazine
Owner’s Manual
© 2001 American Honda Motor Co., Inc - All Rights Reserved.
Y0599D
08B26-S3Y-1000-91
1 of 10
5. Remove the self-tapping screws that fasten the
radio, and pull the unit out toward you.Unplug the
vehicle harness connector and the antenna lead
from the rear of the radio.
7. Detach the clips, and pull the driver's side cowl
carpet down and out of the way.
SELF-TAPPING
SCREW
CLIPS
DRIVER'S SIDE
COWL CARPET
(Pull down and out
toward you.)
ANTENNA
LEAD
VEHICLE HARNESS
CONNECTOR
8. Remove the B-pillar lower trim panel (four
retaining clips). Take care not to damage the
retaining clips.
6. Remove the driver's door sill trim (four retaining
clips).
DRIVER'S DOOR
SILL TRIM
CLIP
B-PILLAR
LOWER TRIM
PANEL
RETAINING
CLIP
© 2001 American Honda Motor Co., Inc - All Rights Reserved.
AII 23268 (0110)
3 of 10
9. Remove the four expansion clips that fasten the
floor carpet, and fold the carpet down and out of
the way.
12. Route the BUS cable above the steering shaft,
and secure it to the vehicle harness with four
short wire ties in the areas shown.
EXPANSION
CLIP
SHORT
WIRE TIES
VEHICLE
HARNESS
STEERING
SHAFT
FUSE BOX
HOOD
OPENER
FLOOR
CARPET
(Fold down.)
BUS
CABLE
Routing the BUS Cable
10. Route one end of the BUS cable up under the
dashboard, and out the radio opening.Position the
BUS cable connector alongside the radio
connector; then secure the BUS cable and the
vehicle harness with two short wire ties in the
areas shown.
13. Route the BUS cable down alongside the fuse
box, and secure it to the body panel with one
cushion tape. Secure the BUS cable to the vehicle
harness with the two short wire ties.
FUSE
BOX
EPT SEALER
SHORT
WIRE TIES
CUSHION
TAPE
SHORT
WIRE TIES
(Position the BUS cable
connector flush with
the radio connector.)
RADIO
CONNECTOR
11. Attach a piece of EPT sealer to the dash support
to protect the BUS cable.
4 of 10
AII 23268 (0110)
© 2001 American Honda Motor Co., Inc - All Rights Reserved.
14. Continue routing the BUS cable toward the rear
of the vehicle. Measure 35 mm below the door
opening, and secure the BUS cable to the body
with four cushion tapes.
18. Remove the rear side trim panel (three
expansion clips).
REAR SIDE
TRIM PANEL
EXPANSION
CLIP
SHORT
35 mm
WIRE TIE
WASHER-BOLT
CUSHION
TAPES
VEHICLE
HARNESS
LEFT TRUNK
SIDE BOARD
15. Secure the BUS cable to the vehicle harness
with one short wire tie in the area shown.
RELAY
19. Remove the left trunk side board by pulling out
on the back and toward you.
16. Open the tailgate, and remove the cargo floor
mat.
20. Locate the relay mounted to the lower trunk panel.
Remove the washer-bolt to free the relay.
CARGO FLOOR MAT
TAILGATE
21. Remove the middle bulkhead cover (pry out the
seven screw covers, and remove the seven
screws).
SCREW
COVER
SELF-TAPPING
SCREW
MIDDLE BULKHEAD
COVER
CARGO BOX
17. Remove the cargo box.
© 2001 American Honda Motor Co., Inc - All Rights Reserved.
AII 23268 (0110)
5 of 10
22. Remove the three clips, and fold down the top
portion of the middle carpet. If the vehicle you are
working on is equipped with rear speakers,
24. Attach one cushion tape around the lower edge
of the hole in the inner panel; then route the BUS
cable toward the rear over the cushion tape.
Secure the BUS cable to the inner panel with
additional cushion tape.
remove the speakers and rear speaker holders.
SPEAKER
HOLDER
CLIP
BUS CABLE
CUSHION TAPE
SCREW
FLOOR
CARPET
(Turn over.)
25. Route the BUS cable down, and secure it to the
trunk panel with two cushion tapes.
CUSHION TAPE
CLIP
23. Continue routing the BUS cable toward the rear
of the vehicle alongside the vehicle harness,
then up and out through the cutout in the area
shown. While wearing gloves to protect your
hands, reach through the speaker hole, and
secure the BUS cable to the vehicle harness
with four short wire ties in the areas shown.
CUTOUT
BUS CABLE
SPEAKER
HOLE
SHORT
WIRE TIES
6 of 10
AII 23268 (0110)
© 2001 American Honda Motor Co., Inc - All Rights Reserved.
Installing the CD Changer
30. Position the front and rear brackets on the CD
changer, and install four 4 x 8 mm washer-
screws into each bracket.
26. Carefully unpack the CD changer. Remove the
three shipping clips, and discard the shipping
cover. Save the shipping clips for your customer
in the event the unit needs to be serviced.
FRONT
BRACKET
CD CHANGER
SHIPPING CLIP
REAR
BRACKET
SHIPPING COVER
(Discard.)
4 x 8 mm
WASHER-
SCREW
ADHESIVE SEAL
4 x 8 mm
WASHER-SCREW
31. Using a utility knife, cut out the inside line of the
center area on the CD changer trim.
27. Install an adhesive seal (included with the CD
changer kit) over each of the three clip holes.
CD CHANGER
TRIM
LEFT LOCKING
COVER
(supplied with
CD Changer kit)
OUTSIDE LINE
Do not cut here.
RIGHT LOCKING
COVER
(supplied with
Cut out.
FOR VERTICAL
CD Changer kit)
INSTALLATION
INSIDE LINE
Cut here.
SPRING ADJUSTING PIN
VERTICAL POSITION
28. Visually check the location of the spring
adjusting pins on both sides of the CD changer.
If the spring adjusting pins are not in the vertical
(V) position, move the pins to the vertical (V)
position with a small flat-tip screwdriver.
29. Remove the backing from the two adhesive
covers, and attach one cover to each side of the
CD changer. Align the two diagonally opposite
holes with the H and V positions.
© 2001 American Honda Motor Co., Inc - All Rights Reserved.
AII 23268 (0110)
7 of 10
32. Place the CD changer trim on the CD changer,
and install the four self-tapping screws.
35. Remove the vehicle harness clip from the hole in
the inner panel.
CLIP
CD CHANGER TRIM
SELF-TAPPING
SCREWS
CD CHANGER
SELF-TAPPING
SCREWS
CLIP NUT
36. Slide one clip nut onto each of the four holes in
the inner panel.
33. Remove 40 to 50 mm of the adhesive backing
from the back of each spacer, and fold them
back. Position the spacers on the CD changer
against the CD changer trim; then carefully
remove the adhesive backings while holding the
spacers in place. Be careful not to tear the
adhesive backings.
37. Apply one EPT sealer to the left taillight harness.
LEFT TAILLIGHT
HARNESS
EPT SEALER
SPACER
ADHESIVE
BACKING
CD CHANGER
EPT SEALER
CD CHANGER
TRIM
SPACERS
34. Wrap one EPT sealer around the connector from
the CD changer.
8 of 10
AII 23268 (0110)
© 2001 American Honda Motor Co., Inc - All Rights Reserved.
38. Cut one piece of EPT sealer in half. Attach the
halves to the rear clip nuts you installed in step
36.
42. Position the CD changer on the studs extending
from the front and rear base brackets, and install
the four flange nuts. Install the CD changer first
on the front bracket, then the rear bracket.
EPT SEALER
FRONT
BRACKET
STUDS
REAR
BRACKET
STUDS
EPT SEALER
(Cut in half.)
CD CHANGER
FLANGE
NUTS
43. Reinstall the relay that was removed in step 20.
REAR BASE FRONT
EPT
BRACKET
BASE
SEALER
BRACKET
6 x 16 mm
6 x 16 mm
WASHER-BOLT
44. Plug the BUS cable connector into the CD
changer.
WASHER-BOLT
39. Position the rear base bracket on the clip nuts,
and install two 6 x 16 mm washer-bolts.Tighten
the bolts securely.
BOLT (reused)
40. Position the front base bracket on the clip nuts
and install two 6 x 16 mm washer-bolts.Tighten
the bolts securely. Attach one EPT sealer over
the head of the lower bracket bolt.
41. Push the clip of the vehicle wire harness
removed in step 35 into the hole in the rear base
bracket.
VEHICLE RELAY
REAR BASE
BRACKET
BUS
CABLE
CD CHANGER CONNECTOR
VEHICLE
HARNESS
CLIP
© 2001 American Honda Motor Co., Inc - All Rights Reserved.
AII 23268 (0110)
9 of 10
45. Secure the BUS cable connector to the vehicle
harness 135 mm away from the vehicle harness
clip with one long wire tie. Attach the BUS cable
to the corner of the body panel with one cushion
tape in the area shown.
47. Reinstall the left trunk side board on the CD
changer brackets, and install the two clips.
BASE
BRACKET
CD CHANGER
BUS CABLE
LONG WIRE TIE
CD CHANGER
BASE BRACKET
135 mm
CLIPS
LEFTTRUNK
SIDE BOARD
BUS CABLE
CONNECTOR
CUSHION TAPE
Secure to the
corner.
48. Reinstall the trunk box, and check that the CD
can be loaded and ejected properly by opening
the lid of the CD changer.
46. Using a utility knife, cut out the marked areas
from the back of the left trunk side board. First
cut out areas A, B, and C, then area D.
49. Plug the BUS cable connector, the radio
connector, and the antenna lead into the rear of
the radio.
RADIO
A
BACK OF
LEFT TRUNK
BUS CABLE
SIDE BOARD
CONNECTOR
B
C
50. Check that all wire harnesses are routed
properly and all connectors are plugged in.
D
51. Reconnect the negative cable to the battery.
52. Reset the clock and the radio station presets.
53. Reinstall all removed parts.
54. Check the operation of the CD changer as
described in the Owner's Manual supplied.
55. Put the CD Changer Owner's Manual and the
shipping screws (removed in step 26) in the glove
box for your customer.
Cut across.
10 of 10
AII 23268 (0110)
© 2001 American Honda Motor Co., Inc - All Rights Reserved.
|