GE Monogram®
Installation
Instructions
30″ Electric
Radiant Cooktop
Model
ZEU30R
Monogram.com
Design Information
Electronic Radiant Cooktop
Design Information
Contents
Models Available .....................................................................................................................................................................3
Advance Planning ...................................................................................................................................................................3
Tools & Materials Required ...................................................................................................................................................4
Preparing the Opening
Minimum Clearances .............................................................................................................................................................4
Overall Cooktop Dimensions .................................................................................................................................................4
Vertical Clearance ..................................................................................................................................................................5
Cutout Dimensions .................................................................................................................................................................5
Wall Coverings, Countertop & Cabinets ...............................................................................................................................5
Installation
Installing Junction Box ...........................................................................................................................................................5
Protecting the Surface of the Cooktop.................................................................................................................................5
Attach Foam Strips .................................................................................................................................................................6
Locate Mounting Parts ..........................................................................................................................................................6
Attach Brackets to Cooktop ..................................................................................................................................................6
Insert the Cooktop into Cutout.............................................................................................................................................6
Attach the Hold Down Bracket.............................................................................................................................................6
Electrical Connections ...........................................................................................................................................................7
Checking Installation & Cooktop Operations ......................................................................................................................8
Models
Available
ZEU30R
Electronic Radiant Cooktop
Remove Installation Instructions from literature pack and
Advance
Planning
The electrical power to the
read them carefully before you begin.
cooktop supply line must be shut
off while connections are being
made. Failure to do so could
result in serious injury or death.
Be sure to place all literature, Owner’s Manual, Installation
Instructions, etc. in a safe place for future reference.
!
GE Monogram®
Installation
Instruction
When preparing cooktop opening, make sure
the inside of the cabinet and the cooktop do
not interfere with each other. (See section on
preparing the opening.)
30" Electric
Radiant Cooktop
Model ZEU30R
Make sure you have all the tools and materials you need
before starting the installation of the cooktop.
Remove packaging materials and literature
package from the cooktop before beginning
installation.
Your home must provide the adequate electrical service
needed to safely and properly use your cooktop. (Refer to
section on electrical requirements.)
Literature Package
Styrofoam
Packaging
When installing your cooktop in your home, make sure all
local codes and ordinances are followed exactly as stated.
Make sure the wall coverings, countertop and cabinets
around the cooktop can withstand heat (up to 200°F)
generated by the cooktop.
ON
Cooktop
3
Preparing the Opening
Electronic Radiant Cooktop
Tools &
Materials
Required
Materials Needed
Tools You Will Need
Phillips Head
Screwdriver
Junction Box
1/8″ Drill Bit &
Electric or Hand
Drill
Pencil
Wire Nuts
Ruler or
Straightedge
Saber Saw
13" MAX. Depth
of unprotected
overhead cabinets
The following MINIMUM clearance
dimensions must be maintained.
Minimum
Clearances
1 1/2" MIN.
clearance from
cutout to side
wall on the right
of the unit
30" MIN.
clearance from
countertop to
unprotected
18" MIN.
height from
countertop to
nearest cabinet on
either side of unit
overhead surface
2" MIN.
clearance from
cutout to side
wall on the left
of the unit
Overall
29 3/4"
Cooktop
Dimensions
20 7/8"
3 1/4"
6 1/4"
21 7/16"
C
L
20 7/8"
3 1/4"
5 1/2"
28"
19 1/4"
CURVED GLASS
4
Installation
Electronic Radiant Cooktop
Vertical
Clearance
Five inches (5″) minimum vertical clearance between
the cooktop bottom and any combustible surfaces.
5"Min.
Vertical Clearance
19 5/8" width of cut
To insure accuracy, it is best to make a
template when cutting the opening in the
counter. Make sure there is clearance
inside the cabinet before cutting the
countertop.
Cutout
28 1/2"
length
of cut
1 3/4" Min.
Between cutout
Dimensions
of the
rear edge and the
wall behind the cooktop
Countertop
2" Min. from
front edge of cutout
and front edge of countertop
Make sure the wall coverings, countertop and
cabinets around the cooktop can withstand heat
(up to 200°F) generated by the cooktop.
Wall
Coverings,
Countertop
& Cabinets
Wall covering,
cabinets and
countertop must
withstand heat up
to 200°F.
Install an approved junction box where it
can be easily reached through the front of
the cabinet where the cooktop will be
located. The cooktop conduit is 3 feet long.
Installing
the
Junction
Box
16"
Min.
Install junction box
so that it can be reached
through the front of
the cabinet.
IMPORTANT: The junction box
must be located where it will allow
!
considerable slack in the conduit
for serviceability.
Protect
Surface of
Cooktop
Bottom of cooktop
Place a towel or tablecloth onto the
countertop. Lay the cooktop upside down
onto the protected surface.
Cloth under Cooktop
(Continued on following page)
5
Installation
Electronic Radiant Cooktop
Bottom of
Cooktop
Apply the foam strips around the outer edge
of the glass. Do not overlap the foam strips.
Attach
Foam Strips
Foam Strips
Cooktop
Glass
MOUNTING
SCREW
Remove the hold down brackets and
screws from the literature package.
Locate
Mounting
Parts
Attach
Brackets to
Cooktop
Screw the Hold Down Bracket to the side of
the cooktop unit. Repeat for opposite side
of cooktop.
Pre-drilled
hole
Bottom of
Cooktop
Foam Strips
Cooktop
Glass
Insert the cooktop centered into the
cutout opening. Make sure the front
edge of the countertop is parallel to
the cooktop. Make final check that all
required clearances are met.
Insert
Cooktop
Into
COOKTOP
Hold
Down
Bracket
Cutout
IMPORTANT: If the cooktop
is being installed into a blind
!
counter (one with no cabinet
opening below), wire connections
must be made before putting the cooktop
into the cutout opening.
Attach
Open the cabinet door and screw the Hold
Down Brackets to the cabinet sides with the
screws provided.
Hold Down
Brackets to
Cabinet
BURNER BOX
SIDES
MOUNTING
SCREW
CABINET
SIDE
USE SUITABLE
FASTENERS FOR
ANCHORAGE IN
CABINET SIDES
6
Electrical Connections
Electronic Radiant Cooktop
When making the wire connections, use the entire length of conduit provided. The conduit must not be
shortened.
Step
Step
1
2
With the cooktop in place, open the front of the cabinet door.
Insert the wires from the conduit through the opening
of the junction box.
Strain
Relief
Clamp
Step
Step
3
4
Red
Ground
Black
Red
Connect the red and black leads from the
cooktop conduit to the corresponding leads
in the junction box.
Ground
Black
wire
location
Red
Once the connections are made, secure wires
together using wire nuts.
Strain
Step
5
Relief
Clamp
Black
Ground
GROUNDING INSTRUCTIONS
The bare ground wire in the conduit is connected to the cooktop frame. Effective January 1, 1996, the
National Electrical Code will not permit grounding through neutral. If used in new construction after
January 1, 1996 or in a mobile home, recreational vehicle or if local codes do not permit grounding
through the neutral white lead, attach the appliance grounding lead (green or copper) to the residence
grounding conductor (green or bare copper) in accordance with local codes. When connecting to a 3
conductor branch circuit, if local codes permit, connect the bare ground connector lead of the cooktop to
the branch circuit neutral (gray or white in color).
IMPORTANT: If the cooktop is being installed into a blind counter (one with no cabinet opening below),
wire connections must be made before putting the cooktop into the cutout opening.
NOTE: ALUMINUM WIRING
A. WARNING:
IMPROPER CONNECTION OF ALUMINUM HOUSE WIRING TO THE COPPER LEADS CAN
RESULT IN A SERIOUS PROBLEM.
B. Splice copper wires to aluminum wiring using special connectors designed and UL approved for joining
copper to aluminum and follow the manufacturer’s recommended connector procedure closely.
NOTE: Wire used, location and enclosure of splices, etc., must conform to good wiring practice and
local codes.
7
Checking the Installation & Cooktop Operation
Electronic Radiant Cooktop
• Remove all protective film if present, and any stickers.
Pre-Test
Checklist
• Check to be sure that all wiring is secure and not pinched or in contact with moving parts.
• Check level of appliance.
• Check that the cooktop is properly grounded.
Operation
Checklist
• Remove all items from the top of the cooktop surface.
• Turn on the power to the cooktop. (Refer to your Owner’s Manual.) Verify that all surface units
operate properly.
• Check that the circuit breaker is not tripped nor the house fuse blown.
• Check that conduit is securely connected to the junction box.
• See Owner’s Manual for troubleshooting list.
•
NOTE TO ELECTRICIAN:
The power leads supplied with this appliance are UL recognized for connections to larger gauge
household wiring. The insulation of these leads is rated at temperatures much higher than the
temperature rating of household wiring. The current carrying capacity of a conductor is governed
by the wire gauge and also the temperature rating of the insulation around the wire.
NOTE: While performing installations
described in this book, safety glasses or goggles
should be worn.
To obtain specific information concerning any
Monogram product or service, call GE Answer
Center® consumer information service at
800.626.2000—any time, day or night or visit our
website at: Monogram.com.
For Monogram local service in your area, call
1.800.444.1845.
NOTE: Product improvement is a continuing
endeavor at General Electric. Therefore,
materials, appearance and specifications are
Monogram®
subject to change without notice.
General Electric Company
Louisville, KY 40225
31-10543
229C4053P527
(09/02 JR)
|