Fujitsu MAY2073RC User Manual

C141-E230-01EN

MAY2073RC

MAY2036RC

HARD DISK DRIVES

PRODUCT/MAINTENANCE MANUAL

REVISION RECORD

Edition Date published

01 June, 2005

Revised contents

Specification No.: C141-E230-**EN

C141-E230

Related Standards

Product specifications and functions described in this manual comply with the following ANSI (*1)

standards and SFF Committee specifications.

Document number

Title

T10/1236D Rev.20

[NCITS.351:2001]

SCSI Primary Commands-2 (SPC-2)

SCSI-3 Block Commands (SBC)

T10/996D Rev. 8c

[NCITS.306:1998]

T10/1157D Rev. 24

T10/1561D Rev. 14

T10/1562D Rev. 05

T10/1601D Rev. 07

SFF-8201 Rev. 2.3

SFF-8223 Rev. 2.4

SCSI Architecture Model-2 (SAM-2)

SCSI Architecture Model-3 (SAM-3)

Serial Attached SCSI (SAS)

Serial Attached SCSI Model-1.1 (SAS 1.1)

Form Factor of 2.5" Disk Drives

2.5" Drive Form Factor with Serial Connector

*1 ANSI = American National Standard Institute

In case of conflict between this manual and any referenced document, this manual takes precedence.

C141-E230

Preface

This manual describes MAY2073RC and MAY2036RC, 2.5" type hard disk drives with an

embedded Serial Attached SCSI (SAS).

This manual details the specifications and functions of the above disk drive, and gives the

requirements and procedures for installing it into a host computer system.

This manual is written for users who have a basic understanding of hard disk drives and

their use in computer systems. The MANUAL ORGANIZATION section describes

organization and scope of this manual. The need arises, use the other manuals.

The organization of this manual, related reference manual and conventions for alert

messages follow.

Overview of Manual

This manual consists of the following seven chapters:

Chapter 1 General Description

This chapter introduces the disk drives standard features, hardware, and system

configuration.

Chapter 2 Specifications

This chapter gives detailed specifications of the disk drives and the installation

environment.

Chapter 3 Data Format

This chapter describes the data structure of the disk, the address method, and what to do

about media defects.

Chapter 4 Installation Requirements

This chapter describes the basic physical and electrical requirements for installing the disk

drives.

Chapter 5 Installation

This chapter explains how to install the disk drives. It includes the notice and procedures

for setting device number and operation modes, mounting the disk drive, and confirming

drive operation.

Chapter 6 Diagnostics and Maintenance

This chapter describes the automatic diagnosis, and maintenance of the disk drive. This

chapter also describes diagnostic methods for operation check and the basics of

troubleshooting the disk drives.

Chapter 7 Error Analysis

This chapter describes in details how collect the information for error analysis and how

analyze collected error information.

C141-E230

Preface

CONVENTIONS USED IN THIS MANUAL

MAY2073RC and MAY2036RC disk drives are described as "the hard disk drives

(HDDs)", "the disk drive" or "the device" in this manual.

Decimal number is represented normally.

Hexadecimal number is represented as X'17B9', 17B9h or 17B9H.

Binary number is represented as "010".

Conventions for Alert Messages

This manual uses the following conventions to show the alert messages. An alert message

consists of an alert signal and alert statements. The alert signal consists of an alert symbol

and a signal word or just a signal word.

The following are the alert signals and their meanings:

This indicates a hazardous situation could result in minor

or moderate personal injury if the user does not perform

the procedure correctly. This alert signal also indicates

that damages to the product or other property, may occur if

the user does not perform the product correctly.

This indicates information that could help the user use the

product more efficiently.

In the text, the alert signal is centered, followed below by the indented message. A wider

line space precedes and follows the alert message to show where the alert message begins

and ends. The following is an example:

(Example)

Damage

Never open the disk enclosure for any reason. Doing so will void any

warranties.

The main alert messages in the text are also listed in the “Important Alert Items.”

Attention

Please forward any comments you may have regarding this manual.

To make this manual easier for users to understand, opinions from readers are needed.

Please write your opinions or requests on the Comment at the back of this manual and

forward it to the address described in the sheet.

C141-E230

Important Alert Items

Important Alert Messages

The important alert messages in this manual are as follows:

A hazardous situation could result in minor or moderate personal injury if the

user does not perform the procedure correctly. Also, damage to the product

or other property, may occur if the user does not perform the procedure

correctly.

Task

Alert message

Page

Installation

Damage

4-3

Never remove any labels from the drive or deface them in any way.

High temperature

5-1, 6-5

To prevent injury, never touch the drive while it is hot. The DE and LSI

become hot during operation and remain hot immediately after turning off

the power.

Damage

5-10

1. When dismounting the drive which is mounted on the

system while power is supplied to it.

• The spindle motor can be stopped by a START/STOP command. It

takes about 15 seconds for the spindle motor to stop completely.

• Then, dismount the drive using the drive mounting/dismounting

mechanism, etc. of the system. If the drive is dismounted while the

spindle motor is running, special care is required to avoid excessive

vibration or shock to the drive. Just in case, stop dismounting once

when SAS connector breaks off contact and wait unitil the spindle

motor stops (about 15 seconds.).

• When storing or transporting the drive, put it in the antistatic bag

(refer to Section 5.1).

C141-230

iii

Important Alert Items

Task

Alert message

Page

5-10

Installation

2. When dismounting the drive which is mounted on the

system while power is not supplied to it.

• Dismount the drive using the drive mounting/dismounting mechanism,

etc. of the system.

• When storing or transporting the drive, put it in the antistatic bag

(refer to Section 5.1).

Diagnostics

and

Maintenance

Data loss

6-5

Save data stored on the disk drive to other media before requesting repair.

Fujitsu does not assume responsibility if data is destroyed during servicing

or repair.

Electreical shock

6-5

Never touch the HDDs while power-feeding.

Damage

1. Always ground yourself with a wrist strap connected to ground before

handling. ESD (Electrostatics Discharge) may cause the damage to the

device.

2. Never use a conductive cleaner to clean the HDDs.

3. Never remove any labels from the drive or deface them in any way.

4. Never remove the PCA.

5. Never open the disk enclosure for any reason.

Damage

6-13

1. Never remove any labels from the drive.

2. Never open the disk enclosure for any reason. Doing so will void any

warranties.

C141-230

MANUAL ORGANIZATION

PRODUCT/

MAINTENANCE MANUAL

1. General Description

2. Specifications

3. Data Format

(This manual)

4. Installation Requirements

5. Installation

6. Diagnostics and Maintenance

7. Error Analysis

INTERFACE

1. Interface

SPECIFICATIONS

2. Command Processing

3. Data Buffer Management

4. Command Specifications

5. Sense Data and Error Recovery Methods

6. Disk Media Management

C141-E230

This page is intentionally left blank.

CONTENTS

CHAPTER 1 General Description ..................................................................1-1

1.1 Standard Features....................................................................................1-1

1.2 Hardware Structure .................................................................................1-5

1.3 System Configuration..............................................................................1-6

CHAPTER 2 Specifications............................................................................2-1

2.1 Hardware Specifications .........................................................................2-1

2.1.1 Model name and order number ...............................................................2-1

2.1.2 Function specifications............................................................................2-2

2.1.3 Environmental specifications..................................................................2-4

2.1.4 Error rate .................................................................................................2-5

2.1.5 Reliability................................................................................................2-5

CHAPTER 3 Data Format ...............................................................................3-1

3.1 Data Space...............................................................................................3-1

3.1.1 Cylinder configuration ............................................................................3-1

3.1.2 Alternate spare area.................................................................................3-4

3.1.3 Track format............................................................................................3-5

3.1.4 Sector format...........................................................................................3-6

3.1.5 Format capacity.......................................................................................3-8

3.2 Logical Data Block Addressing ..............................................................3-8

3.3 Defect Management ..............................................................................3-10

3.3.1 Defect list ..............................................................................................3-10

3.3.2 Alternate block allocation .....................................................................3-10

CHAPTER 4 Installation Requirements ........................................................4-1

4.1 Mounting Requirements..........................................................................4-1

C141-E230

vii

Contents

4.1.1 Dimensions..............................................................................................4-1

4.1.2 Mounting orientations .............................................................................4-2

4.1.3 Notes on mounting ..................................................................................4-3

4.2 Power Supply Requirements ...................................................................4-7

4.3 Connection Requirements .......................................................................4-8

4.3.1 Connector location...................................................................................4-8

4.3.2 Interface connector..................................................................................4-9

4.3.3 Ready LED output signal ......................................................................4-11

CHAPTER 5 Installation................................................................................. 5-1

5.1 Notes on Handling Drives .......................................................................5-1

5.2 Setting......................................................................................................5-3

5.2.1 Port Address ............................................................................................5-3

5.3 Mounting Drives......................................................................................5-3

5.3.1 Mounting procedures...............................................................................5-3

5.4 Checking Operation after Installation and Preparing the HDDs

for Use .....................................................................................................5-4

5.4.1 Checking initial operation .......................................................................5-4

5.4.2 Formatting ...............................................................................................5-5

5.4.3 Setting parameters ...................................................................................5-7

5.5 Dismounting Drives...............................................................................5-10

5.6 Spare Disk Drive ...................................................................................5-10

CHAPTER 6 Diagnostics and Maintenance.................................................. 6-1

6.1 Diagnostics ..............................................................................................6-1

6.1.1 Self-diagnostics .......................................................................................6-1

6.1.2 Test programs ..........................................................................................6-4

6.2 Maintenance Information ........................................................................6-5

6.2.1 Precautions ..............................................................................................6-5

6.2.2 Maintenance requirements ......................................................................6-6

6.2.3 Maintenance levels..................................................................................6-7

viii

C141-E230

Contents

6.2.4 Revision numbers....................................................................................6-7

6.2.5 Tools and test equipment ........................................................................6-8

6.2.6 Tests ........................................................................................................6-9

6.3 Operation Check....................................................................................6-10

6.3.1 Initial seek operation check...................................................................6-10

6.3.2 Operation test ........................................................................................6-10

6.3.3 Diagnostic test.......................................................................................6-10

6.4 Troubleshooting Procedures..................................................................6-11

6.4.1 Outline of troubleshooting procedures..................................................6-11

6.4.2 Troubleshooting with disk drive replacement in the field ....................6-11

6.4.3 Troubleshooting at the repair site..........................................................6-13

6.4.4 Troubleshooting with parts replacement in the factory ........................6-14

6.4.5 Finding possibly faulty parts.................................................................6-14

CHAPTER 7 Error Analysis............................................................................7-1

7.1 Error Analysis Information Collection ...................................................7-1

7.1.1 Sense data................................................................................................7-1

7.1.2 Sense key, additional sense code, and additional sense code qualifier...7-1

7.2 Sense Data Analysis................................................................................7-3

7.2.1 Error information indicated with sense data ...........................................7-3

7.2.2 Sense data (3-0C-03), (4-32-01), (4-40-xx), (4-C4-xx), and

(4-44-xx) .................................................................................................7-4

7.2.3 Sense data (1-1x-xx), (3-1x-xx) and (E-1D-00): Disk read

error.........................................................................................................7-4

7.2.4 Sense data (5-2x-xx), (B-44-xx), (B-47-xx), (B-4B-xx) and

(B-4E-00): interface error .......................................................................7-4

Glossary ...........................................................................................................GL-1

Abbreviation.....................................................................................................AB-1

Index ................................................................................................................. IN-1

C141-E230

Contents

Illustrations

Figures

Figure 1.1 Example of SAS system configuration (Dual port internal

cabled environment)..................................................................... 1-6

Figure 1.2 Example of SAS system configuration (Dual port internal

backplane environment)............................................................... 1-6

Figure 3.1 Cylinder configuration ................................................................. 3-2

Figure 3.2 Spare area in cell.......................................................................... 3-4

Figure 3.3 Alternate cylinder......................................................................... 3-4

Figure 3.4 Track format................................................................................. 3-5

Figure 3.5 Track skew/head skew ................................................................. 3-6

Figure 3.6 Sector format................................................................................ 3-6

Figure 3.7 Alternate block allocation by FORMAT UNIT command ........ 3-11

Figure 3.8 Alternate block allocation by REASSIGN BLOCKS

command.................................................................................... 3-12

Figure 4.1 Dimensions................................................................................... 4-1

Figure 4.2 HDD orientations ......................................................................... 4-2

Figure 4.3 Mounting frame structure example.............................................. 4-4

Figure 4.4 Vent hole location ........................................................................ 4-4

Figure 4.5 Surface temperature measurement points.................................... 4-5

Figure 4.6 Service clearance area.................................................................. 4-6

Figure 4.7 Current waveform (+12V DC)..................................................... 4-7

Figure 4.8 AC noise filter (recommended).................................................... 4-8

Figure 4.9 Connector location ....................................................................... 4-8

Figure 4.10 SAS plug connector overview...................................................... 4-9

Figure 4.11 Recommended external circuit for Ready LED output.............. 4-11

Figure 6.1 Revision label (example) ............................................................. 6-7

Figure 6.2 Indicating revision numbers......................................................... 6-8

Figure 6.3 Test flowchart............................................................................... 6-9

Figure 7.1 Format of extended sense data..................................................... 7-2

C141-E230

Contents

Tables

Table 2.1 Model names and order numbers..................................................2-1

Table 2.2 Function specifications .................................................................2-2

Table 2.3 Environmental/Power requirements .............................................2-4

Table 3.1 Format capacity.............................................................................3-8

Table 4.1 Surface temperature check point and maximum temperature ......4-5

Table 4.2 Interface connector (SAS plug) signal allocation:CN1 ..............4-10

Table 6.1 Self-diagnostic functions ..............................................................6-1

Table 6.2 System-level field troubleshooting.............................................6-12

Table 6.3 Disk drive troubleshooting..........................................................6-13

Table 7.1 Definition of sense data ................................................................7-3

C141-E230

This page is intentionally left blank.

CHAPTER 1

General Description

1.1 Standard Features

1.2 Hardware Structure

1.3 System Configuration

This chapter describes the feature and configuration of the hard disk drives (HDDs).

The HDDs are high performance large capacity 2.5" fixed disk drives with an embedded Serial Attached SCSI

(SAS) controller.

The interface used to connect the HDDs to the host system complies with ANSI T10/1601-D Serial Attached

SCSI-1.1 (SAS-1.1), which covers items ranging from SAS physical layers to SCSI command protocols.

The high-speed data transfer and long-distance transmission capabilities of SAS technology and the powerful

command set the HDDs facilitate creation of high-performance and highly reliable disk subsystems with large

storage capacities.

1.1

Standard Features

(1)

Compactness

The HDDs are a compact enclosure which complies with the 2.5" disk drive form factor.

(2)

Restriction of Use of Hazardous Substances

The amounts of hazardous substances in use in these HDDs have been reduced in accordance with

the Restriction of Use of Hazardous Substances (RoHS) Directive recently issued by European Union

(EU).

Note:

At present, the permissible limits on the use of certain materials specified by the RoHS directive

have not been determined. In such cases, we are using the original criteria set by Fujitsu Limited

while referring to the restrictions already established by End-of-Life (ELV) Directive or by the

national environmental laws of the EU member nations.

C141-E230

1-1

General Description

(3)

SAS Standard

The HDDs are equipped with a serial attached SCSI (SAS) as a host interface.

•

Transfer rate: 1.5Gbps, 3.0Gbps

Number of SAS ports: Two

Full-duplex (simultaneous bidirectional data transfer) is supported.

SCSI commands can manipulate data through logical block addressing, regardless of the physical

characteristics of the disk drive. This enables software to accommodate expansion of system

functionality.

(4)

Dual SAS port support

The HDDs have two pairs of driver and receiver set (PHY) for the SAS to support dual SAS port

connection.

On MAY2073RC and MAY2036RC, Primary and Secondary Ports on SAS plug connector (2

physical links plus power connections) are used for SAS port connection.

(5)

(6)

High-speed data transfer

The maximum data-transfer speed on the SAS is 300.0 MB/s. The large-capacity data buffer of the

HDDs enable the effective use of such high-speed data transfers available on the SAS connection.

Continuous block processing

The addressing method of data blocks is logical block address. The initiator can access data by

specifying block number in a logically continuous data space without concerning the physical

structure of the track or cylinder boundaries.

The continuous processing up to [64K-1] blocks in a command can be achieved, and the HDDs can

perform continuous read/write operation when processing data blocks on several tracks or cylinder.

(7)

(8)

Multi-segment data buffer

The data buffer is 16M bytes. Data is transferred between SAS port and disk media through this data

buffer. This feature provides the suitable usage environment for users.

Cache feature

After executing the READ command, the HDDs read automatically and store (prefetches) the

subsequent data blocks into the data buffer (Read-ahead caching).

The high speed sequential data access can be achieved by transferring the data from the data buffer without

reaccessing the disk in case the subsequent command requests the prefetched data blocks.

The Write Cache feature is supported. When this feature is enabled, the status report is issued

without waiting for completion of write processing to disk media, thereby enabling high speed write

processing.

1-2

C141-E230

1.1 Standard Features

When Write Cache is enabled, you should ensure that the cached data is

surely flushed to the disk media before you turn off the drive's power.

To ensure it, you should issue either the SYNCHRONIZE CACHE

command or the STOP UNIT command with specifying “0” to the

Immediate bit, and then confirm that the command is surely terminated

with the GOOD STATUS.

(9)

Command queuing feature

The HDDs can queue maximum 128 commands, and optimizes the issuing order of queued

commands by the reordering function. This feature realizes the high speed processing.

(10)

(11)

Reserve and release functions

The HDDs can be accessed exclusively in the multi-host or multi-initiator environment by using the

reserve and release functions.

Error recovery

The HDDs can try to recover from errors in the disk drive using its powerful retry processing. If a

recoverable data check occurs, error-free data can be transferred to the initiator after being corrected

in the data buffer. The initiator software is released from the complicated error recover processing

by these error recovery functions of the HDDs.

(12)

(13)

Automatic alternate block reassignment

If a defective data block is detected during read or write the HDDs can automatically reassign its

alternate data block.

Programmable data block length

Data can be accessed in fixed-block length units. The data block length is programmable, and can be

specified at initializing with a multiple of four within the range of 512 to 528 bytes.

Error rate increase

1. The drive format at factory shipment is generally 512 bytes.

2. The recoverable Error of the drive might increase when the format would

be modified from 512 bytes to the following values:

516 bytes, 520 bytes, 524 bytes, 528 bytes.

3. The recoverable Error referred here is sense data (1-13-xx).

C141-E230

1-3

General Description

(14)

Defective block slipping

A logical data block can be reallocated in a physical sequence by slipping the defective data block at

formatting. This results in high speed contiguous data block processing without a revolution delay

due to defective data block.

(15)

(16)

High speed positioning

A rotary voice coil motor achieves fast positioning with high performance access control.

Large capacity

A large capacity can be obtained from the HDDs by dividing all cylinders into several partitions and

changing the recording density on each partition (constant density recording). The disk subsystem

with large capacity can be constructed in the good space efficiency.

(17)

(18)

Start/Stop of spindle motor

Using the SAS primitive or the SCSI command, the host system can start and stop the spindle motor.

Diagnosis

The HDDs have a diagnostic capability which checks internal controller functions and drive

operations to facilitate testing and repair.

(19)

Low power consumption

By using highly integrated LSI components, the power consumption of the HDDs is very low, and

this enables the unit to be used in wide range of environmental conditions.

(20)

(21)

Low noise and low vibration

The noise level is low; approx. 2.9 Bels at Ready for the drive. This makes it ideal for office use.

Microcode downloading

The HDDs implement the microcode download feature. This feature easily achieves maintenance and

function enhancement of the HDDs.

1-4

C141-E230

1.1 Standard Features

1.2

Hardware Structure

The HDDs have a disk enclosure (DE) and a printed circuit assembly (PCA). The DE includes heads

on an actuator and disks on a spindle motor mounted on the DE. The PCA includes a read/write

circuit and a controller circuit.

(1)

(2)

(3)

Disks

The disks have an outer diameter of 65 mm (2.56 inch).

Heads

The heads have MR (Magnet-Resistive) read element Ramp Load type slider.

Spindle motor

The disks are rotated by a direct-drive hall-less DC spindle motor. The motor speed is controlled by

a feedback circuit using the counter electromotive current to precisely maintain the specified speed.

(4)

(5)

(6)

Actuator

The actuator, which uses a rotary voice coil motor (VCM), consumes little power and generates little

heat. The heads at the end of the actuator arm are controlled and positioned via feedback servo loop.

The heads are positioned on the ramp when the power is off or the spindle motor is stopped.

Read/write circuit

The read/write circuit utilizes a read channel mounted with a head IC that supports high-speed

transmission and an MEEPR4ML (Modified Enhanced Extended Partial Response Class 4 Maximum

Likelihood) modulation/demodulation circuit in order to prevent errors being triggered by external

noise and to improve data reliability.

Controller circuit

The controller circuit uses LSIs to increase the reliability and uses a high speed microprocessing unit

(MPU) to increase the performance of the SAS controller.

C141-E230

1-5

General Description

1.3

System Configuration

For the Serial Attached SCSI, the ANSI standard defines Point-to-Point technology. Figure 1.1 and

Figure 1.2 give examples of the SAS system configuration.

Figure 1.1 Example of SAS system configuration (Dual port internal cabled environment)

Figure 1.2 Example of SAS system configuration (Dual port internal backplane environment)

(1)

Port addressing

Every device connected with the SAS protocol has a unique address (SAS address). SAS addresses

are in the Name Address Authority (NAA) IEEE Registered format defined by SCSI Primary

Command-3 (SPC-3).

An SAS address consists of 8 bytes as a unique value set for each device.

The initiator can implement an I/O operation on a disk drive by using the corresponding SAS address

stored by the HDDs.

1-6

C141-E230

CHAPTER 2

Specifications

2.1 Hardware Specifications

This chapter describes specifications of the HDDs.

2.1

Hardware Specifications

2.1.1

Model name and order number

Each model has different recording capacities when shipped.

Table 2.1 lists the model name and order number.

The data format can be changed by reinitializing with the user's system.

Table 2.1

Model names and order numbers

Capacity

(user area)

Model name

Order number

Interface type

MAY2073RC

MAY2036RC

CA06681-B260

CA06681-B160

SAS

73.5 GB (*)

36.7 GB (*)

(*) 1 GB = 1,000,000,000 bytes

C141-E230

2-1

Specifications

2.1.2

Function specifications

Table 2.2 shows the function specifications of the HDDs.

Table 2.2

Function specifications

Specification

Item

MAY2073RC

MAY2036RC

Formatted capacity/device (*1)

Number of disks

73.5 GB (*2)

36.7 GB (*2)

Number of heads

Number of rotations min^-1(rpm)

Average latency time

Track to Track

10,025 ± 0.1 %

2.99 ms

0.2 ms / 0.4 ms

4.0 ms / 4.5 ms

8.0 ms / 9.0 ms

15 s typ. (30 s max.)

15 s typ.

Seek time (*3)

(Read/Write)

Average

Full stroke

Start time

Start/stop time

(*4)

Stop time

Recording mode

Height:

60/63 MEEPRML

15.0 mm max.

External

dimensions

Width:

69.85 +/− 0.25 mm

100.45 mm max.

0.22 kg max.

Depth:

Weight

Power consumption (*5)

4.5 W typ.

Interface

SAS

Cable length: 8 m max.

70.2 Gbit/inch²

37.9 to 63.3 MB/s

1.5 Gbps, 30 Gbps

Areal density

Disk drive

SAS

Data transfer

rate (*6)

Logical data block length

512 to 528 byte (Fixed length) (*7)

SAS (T10/1562D Rev. 05), SAS1.1 (T10/1601D Rev. 07),

SAM-3 (T10/1561D Rev. 14), SAM-2 (T10/1157D Rev. 24),

SPC-2 (T10/1236D Rev. 20), SBC (T10/996D Rev. 8c)

Command specification

Data buffer

16 MB FIFO ring buffer (*8)

2.9 Bels typ.

Acoustic noise (Idle)

(*1) The formatted capacity can be changed by changing the logical block length and using spare sector

space. See Chapter 3 for the further information. The formatted capacity listed in the table is an

estimate for 512 bytes per sector.

(*2) 1 GB = 1,000,000,000 bytes

2-2

C141-E230

2.1 Hardware Specifications

(*3)

The seek time is as follows:

Seek Difference [4096 Cyl/div]

(*4) The start time is the time from power on or start command to when the HDDs are ready, and the stop

time is the time for disks to completely stop from power off or stop command.

(*5) This value indicates in idle mode. Power supply at nominal voltage 1%. 25°C ambient.

(*6) The maximum data transfer rate may be restricted to the response speed of initiator and by

transmission characteristics. 1 MB/s = 1,000,000 bytes/s.

(*7) Refer to 1.1 (13).

(*8) 1 MB = 1,048,576 bytes.

2-3

C141-E230

Specifications

2.1.3

Environmental specifications

Table 2.3 lists environmental and power requirements.

Table 2.3

Environmental/Power requirements

Specification

Item

MAY2073RC

MAY2036RC

Operating

5 to 55 °C

–40 to 70 °C

Non-operating

Temperature

(*1)

Transport (within a week)

DE surface temperature at

operating

5 to 60 °C

Gradient

15 °C/h or less

5 to 95 %RH

Operating

Non operating

Transport (within a week)

Relative

humidity

Maximum wet bulb

temperature

29 °C (no condensation)

Operating (*3)

Non-operating (*4)

Transport (packaged)

Operating

0.6 mm (5 to 20Hz) / 9.8 m/s²(1G) (20 to 300Hz) or less

3.1 mm (5 to 20Hz) / 49m/s²(5G) (20 to 300Hz) or less

980 m/s²(100G) / 1 ms duration

3,920 m/s²(400G) / 1 ms duration

–305 to +3,048 m (–1,000 to +10,000 feet)

–305 to +12,192 m (–1,000 to +40,000 feet)

0.18 A ave.

Vibration (*2)

Shock (*2)

Altitude

Non-operating

Transport (packaged)

Operating

Non-operating

Idle

1.20 A max.

Spin-up

+12V DC

± 5%

1.50 A (peak within 100µs)

0.35 A (about 80 IOPS)

Operating

(reference)

Power

0.40 A (about 200 IOPS)

requirements

(*5)

Idle

0.46 A ave.

Operating

1.20 A max.

+5V DC

± 5%

0.76 A (about 80 IOPS)

Operating

(reference)

0.74 A (about 200 IOPS)

Ripple (+5V, +12V)

250 mVp-p or less (*6)

2-4

C141-E230

2.1 Hardware Specifications

(*1)

(*2)

For detail condition, see Section 4.1.

Vibration applied to the drive is measured at near the mounting screw hole on the frame as much as

possible.

(*3)

(*4)

At random seek write/read and default on retry setting with log sweep vibration.

At power-off state after installation

Vibration displacement should be less than 2.5 mm.

(*5)

(*6)

Input voltages are specified at the drive connector side, during drive ready state.

High frequency noise (over 20MHz) is less than 100 mVp-p.

2.1.4

Error rate

Errors detected during initialization and replaced by alternate block assignments are not included in

the error rate. Data blocks to be accessed should be distributed over the disk medium equally.

(1)

Unrecoverable error rate

Errors which cannot be recovered within 63 retries and ECC correction should not exceed 10 per 10¹⁶

bits read.

(2)

Positioning error rate

Positioning errors which can be recovered by one retry should be 10 or less per 10⁸seeks.

2.1.5

Reliability

(1)

Mean Time Between Failures (MTBF)

MTBF of the HDDs during its life time is 1,400,000 hours (operating: 24 hours/day, 7 days/week

average DE surface temperature: 50°C or less).

Note:

The MTBF is defined as:

Operating time (hours) at all field sites

MTBF

The number of equipment failures from all field sites

Failure of the equipment means failure that requires repair, adjustments, or replacement.

Mishandling by the operator, failures due to bad environmental conditions, power trouble, host

system trouble, cable failures, or other failures not caused by the equipment are not considered.

C141-E230

2-5

Specifications

(2)

Mean Time To Repair (MTTR)

MTTR is the average time taken by a well-trained service mechanic to diagnose and repair a drive

malfunction. The drive is designed for a MTTR of 30 minutes or less.

(3)

Service life

The service life under suitable conditions and treatment is as follows.

The service life is depending on the environment temperature. Therefore, the user must design the

system cabinet so that the average DE surface temperature is as low as possible.

•

DE surface temperature: 40°C or less

DE surface temperature: 41°C to 45°C

DE surface temperature: 46°C to 50°C

DE surface temperature: 51°C to 55°C

DE surface temperature: 56°C to 60°C

5 years

4.5 years

4 years

3.5 years

3 years

DE surface temperature: exceeding 60°C Without warranty

(Keep the DE surface temperature 60°C or less.)

Even if the HDDs are used intermittently, the longest service life is 5 years.

Note:

The "average DE surface temperature" means the average temperature at the DE surface

throughout the year when the HDDs are operating.

(4)

Data security at power failure

Integrity of the data on the disk is guaranteed against all forms of DC power failure except on blocks

where a write operation is being performed. The above does not applied to formatting disks or

assigning alternate blocks.

2-6

C141-E230

CHAPTER 3

Data Format

3.1 Data Space

3.2 Logical Data Block Addressing

3.3 Defect Management

This chapter explains data space definition, logical data block addressing, and defect management on the

HDDs.

3.1

Data Space

The HDDs manage the entire data storage area divided into the following three data spaces.

•

User space: Storage area for user data

Internal test space: Reserved area for diagnostic purposes

System space: Area for exclusive use of HDDs themselves

The user space allows a user access by specifying data. These spaces can be accessed with the

logical data block addressing method described in Section 3.2. The internal test space is used by

Read/write test of self-diagnostics test, but user can’t use direct access. The system space is accessed

inside the HDDs at power-on or during the execution of a specific command, but the user cannot

directly access the system space.

3.1.1

Cylinder configuration

The HDDs allocate cylinders to the user space, Internal test space, and system space. Figure 3.1 is

the cylinder configuration.

Spare areas (alternate areas) for defective sectors are provided in the user space. Several sectors in

the last track of one cell and the last cylinder (alternate cylinders) in one zone are allocated as

alternate areas according to the user's assignment (MODE SELECT command). See Subsection 3.1.2

for details.

C141-E230

3-1

Data Format

-Z

-4

Physics Cylinder

System space

Cylinder0

Head0

Head1

m-1

Cylinder0

m-1

Cylinder0

Head

(a-1)

Zone0

Spare sectors for each cell

m-1

User space

Track

m-1

Spare sectors for each cell

Change

for cell

(b)

Alternate Cell

(b-1)

m-1

Zone1

Zone

(X-1)

(C)

Spare Cylinder

Last Cylinder

Note: Spare sectors on the last track in each cylinder are not necessarily placed at the end of the track

(b-1)

because of a track skew or a cylinder skew. (Details are explained in Subsection 3.1.3.)

Figure 3.1 Cylinder configuration

Apart from the above logical configuration, the HDDs intend to increase the storage capacity by

dividing all cylinders into several zones and changing a recording density of each zone.

3-2

C141-E230

3.1 Data Space

(1)

User space

The user space is a storage area for user data. The data format on the user space (the length of data

block and the number of data blocks) can be specified with the MODE SELECT or MODE SELECT

EXTENDED command.

The user can also specify the number of logical data blocks to be placed in the user space with the

MODE SELECT or MODE SELECT EXTENDED command. When the number of logical data

blocks is specified, as many cylinders as required to place the specified data blocks are allocated in

the user space.

A number starting with 0 is assigned to each cylinder required in the user space in ascending order.

If the number of cylinders do not reach the maximum, the rest of the cylinders will not be used.

Always one cylinder is located at the end of each zone in the user space as an alternate cylinder.

Alternate cylinders will be used for alternate blocks. See Subsections 3.1.2 and 3.3.2 for details.

(2)

(3)

Internal test space

The Internal test space is an area for diagnostic purposes only and its data block length is always

512Byte. The Internal test space consists of 8 cylinders and outer-most cylinder is always assigned

(cylinder −147 to −154). The user cannot change the number of cylinders in the Internal test space or

their positions.

System space

The system space is an area for exclusive use of the HDDs itself and the following information are

recorded.

•

Defect list (P list and G list)

MODE SELECT parameter (saved value)

Statistical information (log data)

Controller control information

The above information is duplicated in several different locations for safety.

Note:

The system space is also called SA space.

C141-E230

3-3

Data Format

3.1.2

Alternate spare area

The alternate spare area consists of the last track of each cell in the user space and an alternate

cylinder allocated to the last cylinder of each zone.

The spare area in each cell is placed at the end of the last track as shown in Figure 3.2. These spare

sectors are located in the end of the track logically, not necessarily located at the end physically

because of track skew or cylinder skew. (Details are explained on Subsection 3.1.3.)

Size can be specified by the MODE SELECT command.

The number of spare sectors per cell can be specified from 0 to 200. The default for the spare sectors

number is 200.

Cell

Note: This drive manages alternate spare areas for each cell, which is a set of cylinders. One cell

consists of 27 cylinders.

Figure 3.2 Spare area in cell

An alternate cylinder is used when spare sectors in a cell are used up or 0 is specified as the number

of spare sectors in a cell. 1 cylinder at the end of each zone of the user space is allocated as alternate

cylinders as shown in Figure 3.3.

The user space and the CE space share the alternate cylinders.

Zone

Note: The number of alternate cylinders cannot be changed.

Figure 3.3 Alternate cylinder

3-4

C141-E230

3.1 Data Space

3.1.3

Track format

(1)

Physical sector allocation

Figure 3.4 shows the allocation of the physical sectors in a track. The length in bytes of each

physical sector and the number of sectors per track vary depending on the logical data block length.

The unused area (G4) exists at the end of the track in formats with most logical data block lengths.

The interval of the sector pulse (length of the physical sector) is decided by the HDDs internal free

running clock frequency. This clock is not equal to the interval of the byte clock for each zone.

Therefore, the physical sector length cannot be described with a byte length.

Servo frame

Figure 3.4 Track format

(2)

Track skew and head skew

To avoid waiting for one turn involved in head and cylinder switching, the first logical data block in

each track is shifted by the number of sectors (track skew and head skew) corresponding to the

switching time. Figure 3.5 shows how the data block is allocated in each track.

At the head switching location in a cylinder, the first logical data block in track t + 1 is allocated at

the sector position which locates the track skew behind the sector position of the last logical data

block sector in track t.

At the cylinder switching location, like the head switching location, the first logical data block in a

cylinder is allocated at the sector position which locates the head skew behind the last logical sector

position in the preceding cylinder. The last logical sector in the cylinder is allocated when

formatting, and is an unused spare sector.

C141-E230

3-5

Data Format

Track skew

Head

Track skew

Head skew

Head

Leading logical

sector in head p+1

Figure 3.5 Track skew/head skew

The number of physical sectors (track skew factor and head skew factor) corresponding to the skew

time varies depending on the logical data block length because the track skew and the head skew are

managed for individual sectors. The HDD automatically determine appropriate values for the track

skew factor and the head skew factor according to the specified logical data block length. The value

can be read out by the MODE SENSE or MODE SENSE EXTENDED command after the track has

been formatted.

3.1.4

Sector format

Each sector on the track consists of an ID field, a data field, and a gap field which separates them.

Figure 3.6 gives sector format examples.

SCT

PLO

SM1 DATA1 SM2 DATA2 BCRC ECC

PAD

G1 Sync

Servo

SCT

G1 Sync

PLO

G1 Sync

SM1 DATA1 SM2 DATA4 BCRC ECC

SM1 DATA1 SM2 DATA3

PAD

Figure 3.6 Sector format

3-6

C141-E230

3.1 Data Space

Each sector on the track consists of the following fields:

(1)

(2)

Gaps (G1, G2, G3)

No pattern is written on the gap field.

PLO Sync

In this field, pattern X'00' is written.

(3)

(4)

Sync Mark (SM1, SM2)

In this field, special pattern is written. This special pattern indicates the beginning of the data field.

Data field (DATA1-DATA4)

User data is stored in the data field of the sector. The length of the data field is equal to that of the

logical data block which is specified with a parameter in the MODE SELECT command. Any

multiple of 4 between 512 and 528 bytes can be specified as the length.

(5)

(6)

(7)

BCRC

It is a 4-byte error detection code. Errors in the ID field. Single burst errors with lengths of up to 32

bits for each logical block can be detected.

ECC

This is the 400 bits code that allows detection and correction of errors in the data field, which is

capable of correcting the single burst error up to 200 bits max. on the fly.

PAD

A specified length of x‘00’ pattern is written in this field. This field includes the variation by rotation

and circuit delay till reading/writing.

C141-E230

3-7

Data Format

3.1.5

Format capacity

The size of the usable area for storing user data on the IDD (format capacity) varies according to the

logical data block or the size of the spare sector area. Table 3.1 lists examples of the format capacity

when the typical logical data block length and the default spare area are used. The following is the

general formula to calculate the format capacity.

[Number of sectors of each zone] = [number of sectors per track × number of tracks per cell –

number of alternate spare sectors per cell] × [number of cells in the zone]

[Formatted capacity] = [total of sectors of all zones] ÷ [number of physical sectors in logical block] ×

[logical data block length]

The following formula must be used when the number of logical data blocks are specified with the

parameter in the MODE SELECT or MODE SELECT EXTENDED command.

[Format capacity] = [logical data block length] × [number of logical data blocks]

The logical data block length, the maximum logical block address, and the number of the logical data

blocks can be read out by a READ CAPACITY, MODE SENSE, or MODE SENSE EXTENDED

command after initializing the disk medium.

Table 3.1

Data block length

512

Format capacity

Model

User blocks

Format capacity (GB)

MAY2073RC

MAY2036RC

143,638,992

71,819,496

73.5 (*)

36.7 (*)

(*) 1 GB = 1,000,000,000 bytes

Note:

Total number of spare sectors is calculated by adding the number of spare sectors in each primary

cylinder and the number of sectors in the alternate cylinders.

3.2

Logical Data Block Addressing

Independently of the physical structure of the disk drive, the HDDs adopt the logical data block

addressing as a data access method on the disk medium. The HDDs relate a logical data block

address to each physical sector at formatting. Data on the disk medium is accessed in logical data

block units. The INIT specifies the data to be accessed using the logical data block address of that

data.

The logical data block addressing is a function whereby individual data blocks are given addresses of

serial hexadecimal numbers in each drive.

3-8

C141-E230

3.2 Logical Data Block Addressing

(1)

Block address of user space

The logical data block address number is consecutively assigned to all of the data blocks in the user

space starting with 0 to the first data block.

The HDDs treat sector 0, track 0, cylinder 0 as the first logical data block. The data block is

allocated in ascending order of addresses in the following sequence (refer to Figure 3.5):

1) Logical data blocks are assigned in ascending order of sector number in the same track.

2) Subsequent logical data blocks are assigned in ascending order of track number in the same head.

Within the same track, logical data blocks are assigned in the same way as step 1).

3) Subsequent logical data blocks are assigned to sectors in every track except the last track in

ascending order of track number in the same cell. Within the same track, logical data blocks are

assigned in the same way as step 1) and 2).

4) For the last track in the same cell, subsequent logical data blocks are assigned to sectors other

than spare sectors in ascending order of sector number.

5) After blocks have been assigned in the same cell according to steps 1) to 4), subsequent logical

data blocks are assigned in ascending order of cell number in the same way as in steps 1) to 4).

Logical data blocks are assigned starting from track 0 in the next cell until the last cylinder

(immediately preceding the alternate cylinder n-1 shown in Figure 3.1) of the zone except

alternate cylinders in cells in the user space.

When the logical data block is allocated, some sectors (track skew and head skew) shown in Figure

3.5 are provided to avoid waiting for one turn involving head and cylinder switching at the location

where the track or the head is physically switched.

See Subsection 3.3.2 for defective/alternate block treatment and the logical data block allocation

method in case of defective sectors exist on the disk.

(2)

Alternate area

Alternate areas in the user space (spare sectors in the cell and alternate cylinders) are not included in

the above logical data block addresses. Access to sectors which are allocated as an alternate block in

the alternate area is made automatically by means of the HDD sector slip treatment or alternate block

treatment (explained in Subsection 3.3.2), so the user does not have to worry about accessing the

alternate area. The user cannot access with specifying the data block on the alternate area explicitly.

C141-E230

3-9

Data Format

3.3

Defect Management

3.3.1

Defect list

Information of the defect location on the disk is managed by the defect list. The following are defect

lists which the HDDs manage.

•

P list (Primary defect list): This list consists of defect location information available at the disk

drive shipment and is recorded in a system space. The defects in this list are permanent, so the

INIT must execute the alternate block allocation using this list when initializing the disk.

•

D list (Data defect list): This list consists of defect location information specified in a FORMAT

UNIT command by the INIT at the initialization of the disk. This information is recorded in the

system space of the disk drive as the G list. To execute the alternate block allocation, the

FORMAT UNIT command must be specified.

•

G list (Growth defect list): This list consists of defective logical data block location information

specified in a REASSIGN BLOCKS command by the INIT, information on defective logical data

blocks assigned alternate blocks by means of the HDD automatic alternate block allocation,

information specified as the D list, and information generated as the C list. They are recorded in

the system space on the disk drive.

The INIT can read out the contents of the P and G lists by the READ DEFECT DATA command.

3.3.2

Alternate block allocation

The alternate data block is allocated to a defective data block (= sectors) in defective sector units by

means of the defect management method inside the HDDs.

The INIT can access all logical data blocks in the user space, as long as there is no error.

Spare sectors to which alternate blocks are allocated can be provided in "alternate cylinders". See

Subsection 3.1.2 for details.

The INIT can specify the size and area for spare sectors by the MODE SELECT command at the

time of the initialization of the disk.

Both of the following are applicable to the alternate block allocation.

•

Sector slip treatment: Defective sectors are skipped and the logical data block corresponding to

those sectors is allocated to the next physical sectors. This treatment is made on the same cell as

the defective sector's and is effective until all spare sectors in that cell are used up.

•

Alternate sector treatment: The logical data block corresponding to defective sectors is allocated

to unused spare sectors in the alternate cylinder.

The alternate block allocation is executed by the FORMAT UNIT command, the REASSIGN

BLOCKS command, or the automatic alternate block allocation. Refer to Chapter 4 “Command

Specifications” and Subsection 5.3.2 “Auto alternate block allocation processing” of the Fibre

Channel Interface Specifications for details of specifications on these commands. The logical data

block is allocated to the next physically continued sectors after the above sector slip treatment is

made. On the other hand, the logical data block is allocated to spare sectors which are not physically

consecutive to the adjacent logical data blocks. If a command which processes several logical data

blocks is specified, the IDD processes those blocks in ascending order of logical data block.

3-10

C141-E230

3.3 Defect Management

(1)

Alternate block allocation during FORMAT UNIT command execution

When the FORMAT UNIT command is specified, the allocation of the alternate block to those

defective sectors included in the specified lists (P, G, or D) is continued until all spare sectors in the

same cell are used up. When they are used up, unused spare sectors in the alternate cylinder are

allocated to the subsequent sectors in the cylinder by means of alternate sector treatment. Figure 3.7

is examples of the alternate block allocation during the FORMAT UNIT command execution.

: n represents a logical data block number

: Defective sector

: Unused spare sector

Figure 3.7 Alternate block allocation by FORMAT UNIT command

During FORMAT UNIT command, alternate block allocation is conducted in following cases:

1) Unrecovered write offtrack condition during a media write

2) Uncorrectable Data Error during a media read (certification) *1

C141-E230

3-11

Data Format

If above errors are detected during FORMAT UNIT command, the HDDs allocate the alternate

block(s) to the defective data blocks. Reassign procedure itself is the same as one in REASSIGN

BLOCKS command.

*1 Certification is permitted when DCRT flag is cleared (DCRT flag=0) in FORMAT UNIT

command.

The HDDs check all initialized logical data blocks by reading them out after the above alternate

block allocation is made to initialize (format) the disk.

(2)

Alternate block allocation by REASSIGN BLOCKS command

When the REASSIGN BLOCKS command is specified, the alternate block is allocated to the

defective logical data block specified by the initiator by means of alternate sector treatment. The

alternate block is allocated to unused spare sectors in the alternate cylinder.

Figure 3.8 is examples of the alternate block allocation by the REASSIGN BLOCKS command.

Example Reassign: Block 16

: n represents a logical data block number

: Defective sector

: Unused spare sector

Figure 3.8 Alternate block allocation by REASSIGN BLOCKS command

3-12

C141-E230

3.3 Defect Management

(3)

Automatic alternate block allocation

Automatic alternate block allocation at read operation

•

If the ARRE flag in the MODE SELECT parameter permits the automatic alternate block allocation,

the HDDs automatically execute the alternate block allocation and data duplication on the defective

data block detected during the READ or READ EXTENDED command. This allocation method is

the same as with the REASSIGN BLOCKS command (alternate sector treatment).

•

Automatic alternate block allocation at write operation

If AWRE flag in the MODE SELECT parameter permits the automatic alternate block allocation, the

HDDs execute two kinds of automatic alternate processing during WRITE command processing as

described below:

Type 1 (Reassignment of Uncorrectable Read Error)

1) Commands to be applied

WRITE

WRITE EXTEND

WRITE at executing WRITE AND VERIFY

2) Application requirements

When any of the above commands is issued to LBA registered in the uncorrectable error log of

the READ command (LBA log of uncorrectable error while the READ command is executed),

the AWRE processing is applied.

3) AWRE processing

The following processings are performed when the LBA matches the one in the uncorrectable

error log:

a) Primary media check

Creates an uncorrectable error pattern (invalid LBA pattern) in the position of the error

LBA, repeats the primary media check up to three times. If the error still occurs after the

check repeated three times, it is judged to be defective. Then, it performs the alternate

processing.

b) Alternate processing

Alternate media check

Writes the data that causes an unrecoverable error into the alternate block, and performs

the media check.

(If the alternate block is a defective sector, the block is registered to the G list, another

alternate block is allocated.)

c) SA and defect map update processing (on alternate side)

When an error occurs in the alternate processing, this WRITE command terminates with error.

When the alternate processing normally terminates, the WRITE command is executed.

C141-E230

3-13

Data Format

Type 2 (Reassignment of write fail sector)

1) Commands to be applied

WRITE

WRITE EXTENDED

FORMAT UNIT

WRITE at executing WRITE AND VERIFY

2) Application requirements / processing

When WRITE/WRITE EXTENDED command detects any Servo error (e.g. Write offtrack error)

and cannot be recovered within pre-determined retry number (specified in Mode Parameter). For

the sectors around defective Servo, alternate blocks are allocated and the data of this WRITE

commands are re-written.

Sectors to be made AWRE shall be following:

the sector where the error occurs and the latter sectors and,

the sectors whose data are logically continual and stored in Cache,

the sectors which will be processed in this Write command and,

the sectors which locate between erroneous Servo -1 and +1 (including Split sector)

This function is also applied for the sector that has already been re-assigned.

Remark:

When a write protection is prohibited through the setting terminal, the auto alternate block

allocation processing specification is disabled.

Automatic alternate block allocation is made up to the following

quantities during the execution of one command:

ARRE = Twice

AWRE (Type 1) = Eight times

AWRE (Type 2) =Maximum number which can be processed within

the recovery time limit

If more than the above mentioned defective block is detected, the

alternate block assignment processing for the first defective block is

executed but the alternate block assignment processing for the second

one is not executed and the command being executed terminates.

However, the initiator can recover the twice error by issuing the same

command again.

When an error is detected in a data block in the data area, recovery

data is rewritten and verified in automatic alternate block allocation

during the execution of the READ or READ EXTENDED command.

Alternate block allocation will not be made for the data block if

recovery is successful.

Example: Even if the data error which is recoverable by the WRITE

LONG command is simulated, automatic alternate block

allocation will not be made for the data block.

3-14

C141-E230

CHAPTER 4

Installation Requirements

4.1 Mounting Requirements

4.2 Power Supply Requirements

4.3 Connection Requirements

This chapter describes the environmental, mounting, power supply, and connection requirements.

4.1

Mounting Requirements

4.1.1

Dimensions

Figures 4.1 show the dimensions of the HDDs and the location of the mounting screw holes.

[Units: mm]

Figure 4.1 Dimensions

C141-E230

4-1

Installation Requirements

4.1.2

Mounting orientations

The permissible orientations of the HDDs are shown in Figure 4.2, and the tolerance of the angle is

5° from the horizontal plane.

As show in Figure 4.2, the drive can be installed flat on any of its six sides. Inclination from a

vertical or horizontal plane should not exceed 5°.

(a) Horizontal –1

(b) Horizontal –2

(d) Vertical –2

(e) Upright mounting –1

(f) Upright mounting –2

Direction of gravity

Figure 4.2 HDD orientations

4-2

C141-E230

4.1 Mounting Requirements

4.1.3

Notes on mounting

Damage

Never remove any labels from the drive or deface them in any way.

(1)

(2)

Mounting screw

The mounting screws must use M3 × 0.5 metric

Mounting frame structure

As for a system frame structure mounting the HDDs, the following attentions are required.

a) The frame never touches any components on the PCA of the HDDs. For example as shown

in Figure 4.3, mount the HDDs with a gap of 2.5 mm or more from the frame.

b) The inward projection of the screw from the HDD frame wall at the corner must be 2.5 mm

0.5 mm.

c) Tightening torque of screw must be secured with 0.49 N·m (5 kgf·cm) 12%.

d) The frame must not distort the HDDs.

e) The impact by an electric screwdriver must not exceed the HDD specifications.

(3)

(4)

Limitation of side-mounting

Use all 4 mounting holds on the both sides.

Limitation of bottom-mounting

Use all 4 mounting holds on the bottom face.

C141-E230

4-3

Installation Requirements

Figure 4.3 Mounting frame structure example

(5)

Vent hole

Never cover the vent hole as shown in Figure 4.4.

Vent hole

Label

Figure 4.4 Vent hole location

4-4

C141-E230

4.1 Mounting Requirements

(6)

Environmental temperature

Temperature condition at installed in a cabinet is indicated with ambient temperature measured

30 mm from the disk drive. At designing the system cabinet, consider following points.

•

Make a suitable air flow so that the DE surface temperature never exceed 60°C.

Cool the PCA side especially with air circulation inside the cabinet. Confirm the cooling effect

by measuring the surface temperature of specific ICs and the DE. These measurement results

must satisfy the temperature condition listed in Table 4.1.

•

Keeping the DE surface temperature at 50°C or below at ambient temperature 30°C, which is a

condition for assuring an MTBF of 1,400,000 hours, requires an air flow of 0.5 m/s or more.

Table 4.1

Surface temperature check point and maximum temperature

No.

Measurement point

DE Surface

Maximum temperature

60°C

80°C

93°C

92°C

90°C

Read channel LSI

VCM/SPM Driver

HDC

MPU

Figure 4.5 Surface temperature measurement points

C141-E230

4-5

Installation Requirements

(7)

Service clearance area

The service clearance area, or the sides which must allow access to the HDDs for installation or

maintenance, is shown in Figure 4.6.

[Surface X]

• Holes for mounting screw

(Both Side)

[Surface Y]

• Interface connection

[Surface Z]

• Holes for mounting screw

Figure 4.6 Service clearance area

(8)

(9)

Environmental magnetic field

Do not install the HDDs in the vicinity of equipment giving off strong magnetic fields, such as

monitors, televisions, or loudspeakers.

Leakage magnetic flux

Do not mount the HDDs near the devices that the leakage magnetic flux influence easily.

4-6

C141-E230

4.2 Power Supply Requirements

4.2

Power Supply Requirements

(1)

Allowable input voltage and current

The power supply input voltage measured at the power supply connector pin of the HDDs (receiving

end) must satisfy the requirement given in Subsection 2.1.3. (For other requirements, see Items (4)

below.)

(2)

Current waveform (reference)

Figure 4.7 shows the waveform of +12V DC.

MAY2073RC

MAY2036RC

Time (2 sec/div)

Figure 4.7 Current waveform (+12V DC)

(3)

(4)

Power on/off sequence

The order of the power on/off sequence of +5V DC and +12V DC, supplied to the HDDs, does not

matter.

Sequential starting of spindle motors

After power is turned on to the HDDs, a large amount of current flows in the +12V DC line when the

spindle motor rotation starts. Therefore, if more than one HDDs are the spindle motors should be

started sequentially using one of the following procedures to prevent overload of the power supply

unit.

a) Control the sending of the NOTIFY (ENABLE SPINUP) primitive so that the spindle motors of

individual disk drives are started in intervals of 12 seconds or more.

b) Turn on the +12V DC power in the power supply unit at intervals of 12 seconds or more to start

the spindle motors sequentially.

C141-E230

4-7

Installation Requirements

(5)

Noise filter

To eliminate AC line noise, a noise filter should be installed at the AC input terminal on the HDD

power supply unit. The specification of this noise filter is as follows:

•

Attenuation: 40 dB or more at 10 MHz

Circuit construction: T-configuration as shown in Figure 4.8 is recommended.

Figure 4.8 AC noise filter (recommended)

4.3

Connection Requirements

4.3.1

Connector location

Figure 4.9 shows a location of the interface connector.

Interface connector (CN1)

(Power lines included)

Figure 4.9 Connector location

4-8

C141-E230

4.3 Connection Requirements

4.3.2

Interface connector

Figure 4.10 shows the SAS type interface connector (SAS plug) overview.

Table 4.2 lists the signal allocation of the SAS plug on the HDDs.

P15

S14

Figure 4.10 SAS plug connector overview

C141-E230

4-9

Installation Requirements

Table 4.2 Interface connector (SAS plug) signal allocation:CN1

Pin No.

Signal

Description

GND for SAS Primary Port

GND

RP+

RP-

SAS Primary Port Receive (positive) signal

SAS Primary Port Receive (negative) signal

GND for SAS Primary Port

SAS Primary Port Transmit (negative) signal

SAS Primary Port Transmit (positive) signal

GND for SAS Primary Port

GND for SAS Secondary Port

SAS Secondary Port Receive (positive) signal

SAS Secondary Port Receive (negative) signal

GND for SAS Secondary Port

SAS Secondary Port Transmit (negative) signal

SAS Secondary Port Transmit (positive) signal

GND for SAS Secondary Port

Not used

GND

TP-

TP+

GND

Rs+

S10

S11

S12

S13

S14

P1 ^Note1

P2 ^Note1

P3 ^Note1

Rs-

GND

Ts-

Ts+

GND

Reserved (not used)

GND

Not used

GROUND

GND

GROUND

GND

GROUND

+5V-Charge

+5V

Pre-charge pin for +5V

+5V power supply input

+5V

+5V power supply input

P10

P11

P12

P13

P14

P15

GND

GROUND

READY LED

GND

READY LED output

GROUND

+12V-Charge

+12V

Pre-charge pin for +12V

+12V power supply input

+12V

Note 1) P1 to P3 are +3.3V power supply input and pre-charge signals, and not used on MAY2073RC and

MAY2036RC.

4-10

C141-E230

4.3 Connection Requirements

4.3.3

Ready LED output signal

Figure 4.11 shows a recommended circuit for external LED connection to Ready LED output

signal.

Figure 4.11 Recommended external circuit for Ready LED output

Either +3.3 V or +5 V can be used for external power supply for LED (Vcc). Current limiting

resister (R) value need to be adjusted depend on the Vcc voltage. For +3.3 V Vcc voltage,

recommended resistance is 220 Ω. For +5 V Vcc voltage, recommended resistance is 330 Ω.

C141-E230

4-11

This page is intentionally left blank.

CHAPTER 5

Installation

5.1 Notes on Handling Drives

5.2 Setting

5.3 Mounting Drives

5.4 Checking Operation after Installation and Preparing

the HDDs for Use

5.5 Dismounting Drives

5.6 Spare Disk Drive

This chapter describes the notes on handling drives, setting, mounting drives, confirming drive operations

after installation and preparation for use, and dismounting drives.

5.1

Notes on Handling Drives

The items listed in the specifications in Table 2.3 must be strictly observed.

(1)

General notes

a) Do not give the drive shocks or vibrations exceeding the value defined in the specifications

because it may cause critical damage to the drive. Especially be careful when unpacking.

b) Do not leave the drive in a dirty or contaminated environment.

c) Since static discharge may destroy the CMOS semiconductors in the drive, note the following

after unpacking:

•

Use an antistatic mat and body grounding when handling the drive.

Hold the DE when handling the drive. Do not touch PCAs except for setting.

High temperature

To prevent injury, never touch the drive while it is hot. The DE and

LSI become hot during operation and remain hot immediately after

turning off the power.

C141-E230

5-1

Installation

(2)

Unpackaging

a) Use a flat work area. Check that the "This Side Up" sign side is up. Handle the package on soft

material such as a rubber mat, not on hard material such as a desk.

b) Be careful not to give excess pressure to the internal unit when removing cushions.

c) Be careful not to give excess pressure to the PCA and interface connector when removing the

drive from the antistatic bag.

d) Do not remove any labels from the drive. Never open the DE for any reason.

Installation/removal/replacement

(3)

a) Do not move the drive when power is turned on or until the drive completely stops (for

15 seconds) after power is turned off.

b) Place and keep removed screws and other parts where they will not get lost or damaged.

c) Keep a record of all maintenance work for replacing.

(4)

(5)

(6)

Packaging

a) Store the drive in the antistatic bag.

b) It is recommended to use the same cushions and packages as those at delivery. If those at

delivery cannot be used, use a package with shock absorption so that the drive is free from direct

shocks. In this case, fully protect the PCA and interface connector so that they are not damaged.

Delivery

a) When delivering the drive, provide packaging and do not turn it over.

b) Minimize the delivery distance after unpacking and avoid shocks and vibrations with cushions.

For the carrying direction at delivery, use one of the mount allowable directions in Subsection

4.1.2.

Storage

a) Provide moistureproof packaging for storage.

b) The storage environment must satisfy the requirements specified in Subsection 2.1.3 when the

drive is not operating.

c) To prevent condensation, avoid sudden changes in temperature.

5-2

C141-E230

5.2 Setting

5.2

Setting

5.2.1

Port Address

Every device that uses the SAS interface has a unique SAS address, and commands use an SAS

address to identify each device for I/O operations. Every HDD is assigned a unique SAS address

before shipment from the factory, so setting of an address is not required before the HDDs are used.

5.3

Mounting Drives

5.3.1

Mounting procedures

Since mounting the drive depends on the system cabinet structure, determine the work procedures

considering the requirements specific to each system. The general mounting method and items to be

checked are shown below.

See Subsection 4.1 for the details of requirements for installing the HDDs.

1) With a system to which an external operator panel is mounted, if it is difficult to access the

connector after the drive is mounted on the system cabinet, connect the external operator panel

cable before mounting the drive.

2) Fix the drive in the system cabinet with four mounting screws as follows:

•

The drive has 8 mounting holes (both sides: 2 × 2, bottom: 4). Fix the drive by using four

mounting holes of both sides of the drive or the bottom.

Use mounting screws of which lengths inside the drive mounting frame are 2.5 mm ±0.5 mm

when the screws are tightened (see Figure 4.3).

When mounting the drive, be careful not to damage parts on the PCA.

3) Confirm the DE is not touching the frame on the system side excluding the screw installing part

after tightening the screws. At least 2.5mm of clearance is required between the DE and the

frame. (Indicated in Figure 4.3)

4) When using an electric screwdriver, use the screwdriver that does not apply a force on the drive

that would exceed the drive specifications.

C141-E230

5-3

Installation

5.4

Checking Operation after Installation and Preparing the HDDs for Use

5.4.1

Checking initial operation

The procedure for verifying operation after power-on is explained below.

Initial diagnosis at the time of power-on:

(1)

(2)

(3)

a) When the HDDs are turned on, the Active LED blinks and the HDDs perform the initial self-

diagnosis (controller hardware diagnosis).

b) When the SAS protocol controller diagnosis is completed normally, the HDDs start the LINK

RESET sequence defined by the SAS protocol to establish synchronization with the connected

SAS devices (e.g., the host system).

c) When the initial diagnosis is completed normally, the HDDs can respond to commands from the

host.

Verifying interface connection:

When verification of initial operation after power-on is completed normally, the host system checks

whether the HDD connection to the interface is normal. The procedure for this check depends on the

host system configuration. The following is a general check procedure:

a) Confirm that the transfer rate and HDD SAS addresses can be recognized during the LINK

RESET sequence.

b) Issue the INQUIRY, WRITE BUFFER, and READ BUFFER commands to verify that data is

received and transmitted normally in the interface.

Verifying disk drive operation :

When the LINK RESET sequence has completed, the host system can issue a spindle motor start

instruction and check whether the disk drive is ready to operate.

a) The host system instructs the spindle motor to start by sending the NOTIFY (ENABLE SPINUP)

primitive to the disk drive.

b) The HDDs do not start the motor until the NOTIFY (ENABLE SPINUP) primitive is issued.

c) The disk drive enters the READY state within about 60 seconds after the NOTIFY (ENABLE

SPINUP) primitive is issued.

d) The HDD Active LED blinks (flashes on and off every 0.5 seconds) while the motor is running.

e) The Active LED remains lit when the HDDs enter the READY state. The host system can use

the TEST UNIT READY command to confirm that the HDDs are in the READY state.

(4)

Responses to operation errors :

a) Confirm again that connectors are securely attached to cables.

b) Check whether the supply voltage is supplied normally. (Measure the voltage at the power

connectors of the HDDs.)

5-4

C141-E230

5.4 Checking Operation after Installation and Preparing the HDDs for Use

c) Issue the REQUEST SENSE command to collect sense data. When sense data has been collected

successfully, perform an analysis to check for recoverable errors, and retry operations for

recovery from any such errors.

(2)

Checking at abnormal end

a) When sense data can be obtained, analyze the sense data and retry recovery for a recoverable

error. Refer to Chapter 5 “Sense Data and Error Recovery Method” of the Interface

Specifications for further details.

5.4.2

Formatting

Since the disk drive is formatted with a specific (default) data format for each model (part number)

when shipped from the factory, the disk need not be formatted (initialized) when it is installed in the

system.

However, when the system needs data attributes different from the default format, all sides of the disk

must be formatted (initialized) according to the procedures below.

The user can change the following data attributes at initialization:

•

Logical data block length

Number of logical data blocks in the user space

Alternate spare area size

This section outlines the formatting at installation. Refer to Subsection 4.1.4 “MODE

SELECT (15)”, 4.1.5 “MODE SELECT EXTENDED (55)” of the Serial Attached SCSI Interface

Specifications for further details.

(1)

MODE SELECT/MODE SELECT EXTENDED command

Specify the format attributes on the disk with the MODE SELECT or MODE SELECT EXTENDED

command. The parameters are as follows.

a. Block descriptor

Specify the size (byte length) of the logical data block in the "data block length" field. To

explicitly specify the number of logical data blocks, specify the number in the "number of data

blocks" field. Otherwise, specify 0 in "number of data blocks" field. In this case, the number of

logical data blocks after initialization is determined by the value specified in the format

parameter (page code = 3) and drive parameter (page code = 4).

b. Format parameter (page code = 3)

Specify the number of spare sectors for each cell in the "alternate sectors/zone" field. It is

recommended not to specify values smaller than the HDD default value in this field.

C141-E230

5-5

Installation

(2)

FORMAT UNIT command

Initialize entire recording surface of the disk with the FORMAT UNIT command. The FORMAT

UNIT command initializes entire surface of the disk using the P lists, verifies data blocks after

initialization, and allocates an alternate block for a defect block detected with verification. With

initialization, the value "00" is written into all bytes of all logical data blocks. Only the position

information of defect blocks detected with verification is registered in the G list. The specifications

are as follows:

a. Specifying CDB

Specify 0 for the "FmtData" bit and the "CmpLst" bit on CDB, 000 for the "Defect List Format"

field, and data pattern written into the data block at initialization for the "initializing data pattern"

field.

b. Format parameter

When the values in step a. are specified with CDB, the format parameter is not needed.

5-6

C141-E230

5.4 Checking Operation after Installation and Preparing the HDDs for Use

5.4.3

Setting parameters

The user can specify the optimal operation mode for the user system environments by setting the

following parameters with the MODE SELECT or MODE SELECT EXTENDED command:

•

Error recovery parameter

Caching parameter

Control mode parameter

With the MODE SELECT or MODE SELECT EXTENDED command, specify 1 for the "SP" bit on

CDB to save the specified parameter value on the disk. This enables the HDDs to operate by using

the parameter value set by the user when power is turned on again.

When the parameters are not set or saved with the MODE SELECT or MODE SELECT

EXTENDED command, the HDDs set the default values for parameters and operates when power is

turned on or after reset. Although the HDD operations are assured with the default values, the

operations are not always optimal for the system. To obtain the best performance, set the parameters

in consideration of the system requirements specific to the user.

This section outlines the parameter setting procedures. Refer to Subsection 4.1.4 “MODE

SELECT (15)”, 4.1.5 “MODE SELECT EXTENDED (55)” of the SAS Specifications for further

details of the MODE SELECT and MODE SELECT EXTENDED commands and specifying the

parameters.

1. At factory shipment of the HDDs, the saving operation for the MODE

SELECT parameter is not executed. So, if the user does not set

parameters, the HDDs operate according to the default value of each

parameter

2. The model select parameter is not saved for each Loop ID of but as the

common parameter for all INIT. In the multi-INIT System, parameter

setting cannot be changed for each INIT.

3. Once parameters are saved, the saved value is effective as long as next

saving operation is executed from the INIT. For example, even if the

initialization of the disk is performed by the FORMAT UNIT command,

the saved value of parameters described in this section is not affected.

4. When the HDDs, to which the saving operation has been executed on a

system, are connected to another system, the user must pay attention to

that the HDDs operate according to the saved parameter value if the

saving operation is not executed at installation.

5. The saved value of the MODE SELECT parameter is assumed as the

initial value of each parameter after the power-on, the RESET condition..

The INIT can change the parameter value temporary (actively) at any

timing by issuing the MODE SELECT or MODE SELECT EXTENDED

command with specifying "0" to the SP bit in the CDB.

C141-E230

5-7

Installation

(1)

Error recovery parameters

The following parameters are used to control operations such as HDD internal error recovery:

a. Read/write error recovery parameters (page code = 1)

Parameter

Default value

1 (enabled)

• AWRE:

• ARRE:

Automatic alternate block allocation at Write

operation

Automatic alternate block allocation at read

operation

1 (enabled)

• TB:

Uncorrectable data transfer to the INIT

Immediate correction of correctable error

Report of recovered error

0 (disabled)

1 (enabled)

0 (disabled)

0 (Correction is

enabled.)

• EER:

• PER:

• DCR:

Suppression of ECC error correction

• Retry count at read operation

• Retry count at write operation

• Recovery time limit

30 sec

b. Verify error recovery parameters (page code = 7)

Parameter

Default value

• ERR:

• PER:

• DTE:

Immediate correction of recoverable error

Report of recovered error

Stop of command processing at successful

error recovery

1 (enabled)

0 (disabled)

0 (Processing is

continued.)

• DCR:

Suppression of ECC error correction

0 (Correction is

enabled.)

• Retry count at verification

c. Additional error recovery parameters (page code = 21)

Parameter

Default value

• Retry count at seek error

Notes:

1. The user can arbitrarily specify the following parameters according to the system

requirements:

•

ARRE

AWRE

PER

2. The user also can arbitrarily specify parameters other than the above. However, it is

recommended to use the default setting in normal operations.

5-8

C141-E230

5.4 Checking Operation after Installation and Preparing the HDDs for Use

(2)

Caching parameters

The following parameters are used to optimize HDD Read-Ahead caching operations under the

system environments. Refer to Chapter 3 “Data Buffer Management” of the Serial Attached SCSI

Interface Specifications for further details.

Parameter

Initiator control

Default value

• IC:

0 (Drive-specific

control (page

cache))

• RCD:

• WCE:

• MS:

Disabling Read-Ahead caching operations

Write Cache Enable

0 (enabled)

1 (enabled)

Specifying the multipliers of "minimum

0 (Specifying

prefetch" and "maximum prefetch" parameters

absolute value)

• DISC:

Prefetch operation after track switching during

prefetching

1 (enabled)

• Number of blocks for which prefetch is suppressed

• Minimum prefetch

X'FFFF'

X'0000'

• Maximum prefetch

X' XXXX'

(1 cache segment)

• Number of blocks with maximum prefetch restrictions

• Number of segments

X'FFFF'

X'08'

Notes:

1. When Read-Ahead caching operations are disabled by the caching parameter, these

parameter settings have no meaning except write cache feature.

2. Determine the parameters in consideration of how the system accesses the disk. When the

access form is not determined uniquely because of the processing method, the parameters

can be re-set actively.

3. For sequential access, the effective access rate can be increased by enabling Read-Ahead

caching operations and Write Cache feature.

(3)

Control mode parameters

The following parameters are used to control the tagged queuing and error logging.

a. Control mode parameters

Parameter

• Queue algorithm modifier

Default value

0 (Execution sequence of

read/write commands is

optimized.)

• QErr:

Resume or abort remaining suspended

commands after sense pending state

0 (command is resumed)

C141-E230

5-9

Installation

(4)

Port control parameters

The following parameters are used to control the ready LED signal behavior.

Parameter

Default value

Ready LED meaning

5.5

Dismounting Drives

Since the method and procedure for dismounting the disk drive for replacement of the drive, etc.

depends on the locker structure of the system, etc., the work procedure must be determined in

consideration of the requirements specific to the system. This section describes the general

procedure and notes on dismounting the drive.

Damage

1. When dismounting the drive which is mounted on the system while power is

supplied to it.

•

The spindle motor can be stopped by a START/STOP command. It

takes about 15 seconds for the spindle motor to stop completely.

Then, dismount the drive using the drive mounting/dismounting

mechanism, etc. of the system. If the drive is dismounted while the

spindle motor is running, special care is required to avoid excessive

vibration or shock to the drive. Just in case, stop dismounting once

when SAS connector breaks off contact and wait unitil the spindle

motor stops (about 15 seconds.).

•

When storing or transporting the drive, put it in the antistatic bag

(refer to Section 5.1).

2. When dismounting the drive which is mounted on the system while power is

not supplied to it.

•

Dismount the drive using the drive mounting/dismounting mechanism,

etc. of the system.

•

When storing or transporting the drive, put it in the antistatic bag

(refer to Section 5.1).

5.6

Spare Disk Drive

See Subsection 2.1.1, “Model name and order number,” to order a disk drive for replacement or as a

spare

5-10

C141-E230

CHAPTER 6

Diagnostics and Maintenance

6.1 Diagnostics

6.2 Maintenance Information

6.3 Operation Check

6.4 Troubleshooting Procedures

This chapter describes diagnostics and maintenance information.

6.1

Diagnostics

6.1.1

Self-diagnostics

The HDDs have the following self-diagnostic function. This function checks the basic operations of

the HDDs.

•

Initial self-diagnostics

Online self-diagnostics (SEND DIAGNOSTIC command)

Table 6.1 lists the contents of the tests performed with the self-diagnostics. For a general check of

the HDDs including the operations of the host system and interface, use a test program that runs on

the host system (see Subsection 6.1.2).

Table 6.1

Self-diagnostic functions

C141-E230

6-1

Diagnostics and Maintenance

Brief test contents of self-diagnostics are as follows.

a. Hardware function test

This test checks the basic operation of the controller section, and contains following test.

•

RAM (microcode is stored)

Peripheral circuits of microprocessor (MPU)

Memory (RAM)

Data buffer

b. Seek test

This test checks the positioning operation of the disk drive using several seek modes (2 points

seek, 1 position sequential seek, etc.). The positioning operation is regarded as success when the

seek operation to the target cylinder is completed.

c. Write/read test

This test checks the write/read function by using the Internal test space of the disk drive.

(1)

Initial self-diagnostics

When the HDDs are turned on, they run the initial self-diagnostics. The initial self-diagnostics test

the basic operations of hardware functions.

If the initial self-diagnostics detect an error, the LED on the drive blinks. The HDDs in this state

post the CHECK CONDITION status to all I/O operation requests except the REQUEST SENSE

command. The initiator can collect sense data when the CHECK CONDITION status is posted.

Sense data contains detailed information on the error detected by the initial self-diagnostics.

When sense data has been collected after the CHECK CONDITION status has been posted, the

CHECK CONDITION status continues and the LED keeps blinking. This status can be cleared only

when the HDDs are turned off and turned on again. When the status is cleared, the HDDs run the

initial self-diagnostics again.

The HDDs do not reply to requests from the host system for a maximum of 2 seconds after the start

of the initial self-diagnostics. Thereafter, the HDDs can accept I/O operation requests normally, but

any received command, except commands that are executable even in the not ready state, is

terminated with the CHECK CONDITION status until the spindle motor reaches the normal

rotational speed and the HDDs become ready. The commands that are executable even in the not

ready state are executed in parallel with the initial self-diagnostics, or they are queued by the

command queuing feature and executed when the initial self-diagnostics is completed.

If the initial self-diagnostics detect an error, the CHECK CONDITION status is posted for all of the

commands received and queued during the initial self-diagnostics.

6-2

C141-E230

6.1 Diagnostics

(2)

Online self-diagnostics (SEND DIAGNOSTIC command)

The INIT can make the HDDs execute self-diagnostics by issuing the SEND DIAGNOSTIC

command.

The INIT specifies the execution of self-diagnostics by setting 1 for the SelfTest bit on the CDB in the

SEND DIAGNOSTIC command and specifies the test contents with the UnitOfl bit.

When the UnitOfl bit on the CDB is set to 0, the HDDs execute the hardware function test only once.

When UnitOfl bit is set to 1, the HDDs execute the hardware function test, seek (positioning) test,

and data write/read test for the Internal test space only once.

a. Error recovery during self-diagnostics

During the self-diagnostics specified by the SEND DIAGNOSTIC command, when the

recoverable error is detected during the seek or the write/read test, the HDDs perform the error

recovery according to the MODE SELECT parameter value (read/write error recovery parameter,

additional error recovery parameter) which the INIT specifies at the time of issuing the SEND

DIAGNOSTIC command.

PER

Operation of self-diagnostics

The self-diagnostics continues when the error is recovered. The self-

diagnostics terminates normally so far as the unrecoverable error is not

detected.

The self-diagnostics continues when the error is recovered. If the

unrecoverable error is not detected, the consecutive tests are executed till last

test but the self-diagnostics terminates with error. The error information

indicates that of the last recovered error.

b. Reporting result of self-diagnostics and error indication

When all specified self-diagnostics terminate normally, the HDDs post the GOOD status for the

SEND DIAGNOSTIC command.

When an error is detected in the self-diagnostics, the HDDs terminate the SEND DIAGNOSTIC

command with the CHECK CONDITION status.

When the CHECK CONDITION status is posted, sense data contains detailed information on the

error detected by the initial self-diagnostics.

The HDD status after the CHECK CONDITION status is posted differs according to the type of

the detected error.

a) When an error is detected in the seek or write/read test, the subsequent command can be

accepted correctly. When the command other than the REQUEST SENSE is issued from

the same INIT, the error information (sense data) is cleared.

C141-E230

6-3

Diagnostics and Maintenance

b) When an error is detected in the hardware function test, the HDDs post the CHECK

CONDITION status for all I/O operation request except the REQUEST SENSE command.

The error status is not cleared even if the error information (sense data) is read. Only when

the power is turned off or re-turned on, the status can be cleared. When this status is

cleared, the HDDs execute the initial self-diagnostics again (see item (1)).

Refer to Subsection 4.4.1 “SEND DIAGNOSTIC (1D)” of the Interface Specifications for further

details of the command specifications.

6.1.2

Test programs

The basic operations of the HDD themselves itself can be checked with the self-diagnostic function.

However, to check general operations such as the host system and interface operations in a status

similar to the normal operation status, a test program that runs on the host system must be used.

The structure and functions of the test program depend on the user system requirements. Generally,

it is recommended to provide a general input/output test program that includes devices connected to

the input/output devices on other I/O ports.

Including the following test items in the test program is recommended to test the HDD functions

generally.

(1)

(2)

(3)

Interface test

The operations of the data buffer on the HDDs are checked with the WRITE BUFFER and READ

BUFFER commands.

Basic operation test

The basic operations of the HDDs are checked by executing self-diagnosis with the SEND

DIAGNOSTIC command (see Subsection 6.1.1).

Random/sequential read test

The positioning (seek) operation and read operation are tested in random access and sequential

access modes with the READ, READ EXTENDED, or VERIFY command.

6-4

C141-E230

6.2 Maintenance Information

6.2

Maintenance Information

See Section 5.1 for notes on packing and handling when returning the disk drive.

Data loss

Save data stored on the disk drive to other media before requesting

repair. Fujitsu does not assume responsibility if data is destroyed

during servicing or repair.

6.2.1

Precautions

Take the following precautions to prevent injury during maintenance and troubleshooting:

High temperature

To prevent injury, never touch the drive while it is hot. The DE and

LSI become hot during operation and remain hot immediately after

turning off the power.

Electreical shock

Never touch the HDDs while power-feeding.

Take the following precautions to prevent disk drive damage during maintenance and

troubleshooting:

Damage

1. Always ground yourself with a wrist strap connected to ground

before handling. ESD (Electrostatics Discharge) may cause the

damage to the device.

2. Never use a conductive cleaner to clean the HDDs.

3. Never remove any labels from the drive or deface them in any way.

4. Never remove the PCA.

5. Never open the disk enclosure for any reason.

C141-E230

6-5

Diagnostics and Maintenance

6.2.2

Maintenance requirements

Preventive maintenance

(1)

Preventive maintenance is not required.

(2)

(3)

Service life

See "(3) Service life," in Section 2.1.5.

Parts that can be replaced in the field

The PCA cannot be replaced in the field. The DE cannot be replaced in the field.

(4)

Service system and repairs

Fujitsu has the service system and repair facility for the disk drive. Contact Fujitsu representative to

submit information for replacing or repairing the disk drive. Generally, the following information

must be included:

a) Model part number (P/N), revision number, serial number (S/N), and date of manufacturing

b) Error status

•

Date when the error occurred

System configuration

Environmental conditions (temperature, humidity, and voltage)

c) Error history

d) Error contents

•

Outline of inconvenience

Issued commands and specified parameters

Sense data

Other error analysis information

6-6

C141-E230

6.2 Maintenance Information

6.2.3

Maintenance levels

If a disk drive is faulty, replace the whole disk drive since repair requires special tools and

environment. This section explains the two maintenance levels.

(1)

Field maintenance (disk drive replacement)

•

This replacement is done at the user's site.

Replacement uses standard tools.

Replacement is usually done by the user, retail dealer, distributor, or OEM engineer.

(2)

Factory maintenance (parts replacement)

•

This replacement can only be done by Fujitsu.

Replacement includes maintenance training and OEM engineer support. OEM engineers usually

support retail dealers and distributors.

•

Replacement uses factory tools and test equipment.

6.2.4

Revision numbers

The revision number of the disk drive is represented with a letter and a number indicated on the label

attached on the HDDs. Figure 6.1 shows an example of the label.

Figure 6.1 Revision label (example)

C141-E230

6-7

Diagnostics and Maintenance

(1)

Indicating revision number at factory shipment

When the disk drive is shipped from the factory, the revision number is indicated by deleting

numbers in the corresponding letter line up to the corresponding number with = (see Figure 6.2).

(2)

Changing revision number in the field

To change the revision number because parts are replaced or other modification is applied in the

field, the new level is indicated by enclosing the corresponding number in the corresponding letter

line with bold line (see Figure 6.2).

When the revision number is changed after the drive is shipped from

the factory, Fujitsu issues "Engineering Change Request/Notice" in

which the new revision number is indicated. When the user changes

the revision number, the user should update the revision label as

described in item (2) after applying the modification.

Rev. A2

At shipment

Revising at field

Rev. A3

Figure 6.2 Indicating revision numbers

6.2.5

Tools and test equipment

Disk drive troubleshooting and repair in the field require only standard hand tools. No special tools

or test equipment are required.

This manual does not describe the factory-level tools and test equipment.

6-8

C141-E230

6.2 Maintenance Information

6.2.6

Tests

This disk drive can be tested in the following ways:

•

Initial seek operation check (See Subsection 6.3.1)

Operation test (See Subsection 6.3.2)

Diagnostic test (See Subsection 6.3.3)

Figure 6.3 shows the flow of these tests.

Start

Start self-test by

turning the power on

Check host system

(Table 6.2)

Test results OK?

Yes

Analyze system-related

error

Host system

normal?

Execute an operation

test using a host

computer or test

equipment

Yes

Replaced or repair

disk drive

Test results OK?

Disk drive

normal?

Yes

Continue operation

Execute diagnostic

test using a host

computer or test

equipment

Test results OK?

Yes

Test using voltage or

temperature stress

Analyze disk drive

error (Table 6.3)

Test results OK?

Yes

Normal

Figure 6.3 Test flowchart

C141-E230

6-9

Diagnostics and Maintenance

6.3

Operation Check

6.3.1

Initial seek operation check

If an error is detected during initialization by the initial seek operation check routine at power-on, the

spindle motor of the disk drive stops, and then the disk drive becomes unusable.

For an explanation of the operation check before the initial seek, refer to the Section 5.4.

6.3.2

Operation test

While the host computer is processing data, the HDDs monitor disk drive operation including data

processing, command processing, and seek operations. If the HDDs detect an error, the HDDs post

the error to the INIT. The INIT then posts the error to the user.

The user may detect an intermittent or nonfatal error such as abnormal noise, abnormal odor, or very

slow operation.

An error posted in an operation test must be investigated. Replace the disk drive to see whether the

error was caused by the disk drive.

Often, errors posted in an operation test may be caused by the host system. Possible causes include

insufficient power capacity, loose cable connection, insufficient timing or insufficient mechanical

play, and problems related to other systems.

If an operation error is detected by the error detection circuit of the disk drive, an interrupt occurs.

The interrupt is posted to the MCU on the PCA. The MCU stops the currently processed command,

and causes the CHECK CONDITION status to post the error to the INIT.

When receiving the CHECK CONDITION status, the INIT collects detailed information via SENSE

data.

To analyze the error posted in the operation test, reconstruct the conditions in which the error

occurred. Then, start troubleshooting the whole host system by replacing the disk drive.

6.3.3

Diagnostic test

The diagnostic test is executed to find a faulty subassembly in a faulty disk drive, or to check disk

drive performance. This test is usually a combination of specific disk drive functions or group of

functions. This test may be executed using a different host computers or test equipment and away

from the environment where the error first occurred.

To analyze the error posted in the diagnostic test, reconstruct the conditions in which the error

occurred. Then, look for a possibly faulty subassembly or part of the disk drive.

The procedures to be used in this test depend largely on the type of test equipment used, and are not

covered by this manual.

6-10

C141-E230

6.4 Troubleshooting Procedures

6.4

Troubleshooting Procedures

6.4.1

Outline of troubleshooting procedures

This section explains the troubleshooting procedures for disk drive errors.

Depending on the maintenance level, analyze the error to detect a possibly faulty part (disk drive, or

disk drive part).

Full-scale troubleshooting is usually required if the error cause is not known. If the error cause is

clear (e.g., abnormal noise in disk enclosure or burning of the PCA), troubleshooting is

straightforward.

6.4.2

Troubleshooting with disk drive replacement in the field

At this level of maintenance, we recommend replacing the disk drive as a unit. If replacing the disk

drive rectifies the fault, return the removed disk drive to the factory, for test and repair. If the newly

installed disk drive does not rectify the fault another part of the system is faulty.

Table 6.2 summarizes system-level field troubleshooting. Troubleshooting must be done in the field,

to find faulty part (disk drive or system).

C141-E230

6-11

Diagnostics and Maintenance

Table 6.2

System-level field troubleshooting

Item

DC power level

Recommended work

Check that the DC voltage is within the specified range (±5%).

For +5V DC, measure the voltage between pin 20 (+5V) of the interface

connector and the nearest PCA mounting screw (GND) from the

interface connector, and confirm the value is from 4.75 to 5.25 VDC.

For +12V DC, measure the voltage between pin 2 (+12V) of the

interface connector and the nearest PCA mounting screw (GND) from

the interface connector, and confirm the value is from 11.4 to 12.6 VDC.

Electrical noise

Make sure the maximum ripple peak-to-peak value of +5V DC is within

250 mV and +12V DC is within 250 mV.

Make sure the high frequency noise (over 20 MHz) is less than

100 mVp-p.

System cables

Check that all system cables are connected correctly.

System diagnostic test

When possible, execute the system level diagnostic routine as explained

in the host computer manual. This gives a detailed report of a possible

fault.

Intermittent or nonfatal errors

Check the AC voltage from the power supply. Check the DC voltage

level at the power connector for the disk drive.

If the AC voltage level is abnormal or there is a lot of electrical noise,

notify the user of the error.

If the DC voltage level is unstable, replace the power supply unit.

If possible, replace the disk drive. If replacing the disk drive does not

eliminate the error, the removed disk drive is probably not faulty. To

continue error analysis, refer to the hardware and software manuals

supplied with the system.

6-12

C141-E230

6.4 Troubleshooting Procedures

6.4.3

Troubleshooting at the repair site

For maintenance at this level, we recommend additional testing of the disk drive and signal checking.

The sense data posted from the HDDs help with troubleshooting. This sense data makes the error type clear

(functional, mechanical, or electrical error). Chapter 7 error analysis by sense data, and gives

supplementary information on finding the error cause (faulty part).

Table 6.3 lists how to detect a faulty disk drive subassembly. This fault finding requires a working

host computer or disk drive test equipment to recreate the error conditions.

If the detected error cannot be recreated in an ordinary test, disk drive conditions can be changed to

force the error to recur. This is done by changing the DC voltage or the ambient temperature of the

disk drive.

If the error does not recur with changed conditions, the disk drive is not faulty. If no error occurs in

the disk drive test, notify the user of the test results, and find out from the user the environment

conditions where the disk drive is used.

Table 6.3

Disk drive troubleshooting

Recommended action

Item

Frequent or repeated seek errors

Collect sense data, and see Chapter 7.

Replace the disk drive, and check that the test method is correct. If the

error recurs, it is likely that the disk drive is normal but the test method

is incorrect.

Intermittent or nonfatal errors

Replace the disk drive, and check that the test method is correct. If the

error recurs, it is likely that the disk drive is normal but the test method

is incorrect.

To check performance, change the disk drive conditions by changing

the voltage or temperature.

If the disk drive error recurs or a possibly faulty part is found by troubleshooting, return the complete

disk drive to the factory for repair. A media defect list must be included with the disk drive returned

to the factory.

If the possibly faulty part is the disk enclosure, return the whole disk drive to the factory for repair.

Also if a clear error (erroneous servo track information or noisy drive) is detected in the disk

enclosure, return the whole disk drive to the factory. A media defect list must be included with the

disk drive returned to the factory.

Damage

1. Never remove any labels from the drive.

2. Never open the disk enclosure for any reason. Doing so will void

any warranties.

C141-E230

6-13

Diagnostics and Maintenance

6.4.4

Troubleshooting with parts replacement in the factory

This manual does not cover troubleshooting at the factory level.

6.4.5

Finding possibly faulty parts

Finding possibly faulty parts in the field was explained in Subsection 6.4.2. This manual does not

cover finding possibly faulty parts at the factory level.

6-14

C141-E230

CHAPTER 7

Error Analysis

7.1 Error Analysis Information Collection

7.2 Sense Data Analysis

This chapter explains in detail how sense data collected from a disk drive is used for troubleshooting. Sense

data reflects an error in the disk drive, and helps with troubleshooting.

A sense key, additional sense code, and additional sense code qualifier, taken from various sense data are

repeated. Also in this chapter, troubleshooting is performed using these three codes. Unless otherwise

specified, "sense data" means the above three codes. When sense data is represented as (x-xx-xx), the

leftmost x is a sense key, the middle xx is an additional sense code, and the rightmost x is an additional sense

code qualifier.

7.1

Error Analysis Information Collection

Sense data

7.1.1

When HDDs post a CHECK CONDITION status, the current command or queued command is

cleared. In such a case, the HDDs generate sense data about the command-issuing INIT. The INIT

can read the sense data by reading the sense data added to the response frame of the command where

an error occurred (Auto Sense function).

7.1.2

Sense key, additional sense code, and additional sense code qualifier

If an error is detected in a disk drive, the error status is indicated in the sense data collected from the

disk drive. Figure 7.1 shows the positions of a sense key, additional sense code, and additional sense

code qualifier.

C141-E230

7-1

Error Analysis

Bit 7

Byte 0 Valid

X‘70’ or X‘71’ (error code)

X‘00’

ILI

Sense key

[MSB]

Information

[LSB]

X‘28’ (additional sense data length)

Command-specific information

[MSB]

Basic

information

[LSB]

Additional sense code

Additional sense code qualifier

X‘00’

15 SKSV

Sense key-specific information

Port

CDB operation code

Additional

information

Detail information

ILI:

Incorrect Length Indicator

MSB: Most Significant Byte

LSB: Least Significant Byte

SKSV: Sense Key Specific Valid

Figure 7.1 Format of extended sense data

7-2

C141-E230

7.2 Sense Data Analysis

7.2

Sense Data Analysis

7.2.1

Error information indicated with sense data

Subsection 7.2.2 onwards explain troubleshooting using sense data. For details of the following

sense data, refer to Chapter 5 “Sense Data Error Recovery Methods” of the Interface Specifications.

Table 7.1 lists the definition of sense data. For details of sense data, refer to the Interface

Specifications.

Table 7.1

Definition of sense data

Sense data

Additional

sense code

qualifier

Definition

Sense

key

Additional

sense code

A write to a disk terminated abnormally.

Failed to update the defect list (due to unrecoverable error during

write, verify error after write.).

An error occurred in power-on self-diagnosis.

A drive error occurred.

A disk read error occurred.

Data discrepancy found by VERIFY command byte check.

A SCSI error, such as an invalid operation code, occurred.

A hardware error occurred inside HDDs.

An interface error occurred.

4 or B

An interface error occurred.

An overlap command was issued.

C141-E230

7-3

Error Analysis

7.2.2

Sense data (3-0C-03), (4-32-01), (4-40-xx), (4-C4-xx), and (4-44-xx)

Sense data (3-0C-03), (4-32-01), (4-40-xx), (4-C4-xx), and (4-44-xx) indicate one of the following:

•

A target sector could not be detected using the sector counter.

A seek process overran the specified time.

A write to a disk terminated abnormally.

An error occurred in power-on self-diagnosis.

A drive error occurred.

The symptoms above are generally caused by an error in a PCA or DE.

7.2.3

Sense data (1-1x-xx), (3-1x-xx) and (E-1D-00): Disk read error

If sense data (1-1x-xx), (3-1x-xx) or (E-1D-00) occurs frequently in a specific block of a disk, there

is disk damage that was not recorded in the media defect list. In this case, assign an alternate block

to the error-detected block using a REASSIGN BLOCKS command. For an explanation of the

REASSIGN BLOCKS command, refer to Subsection 4.3.2 “REASSIGN BLOCKS (07)” of the

Interface Specifications.

If this error occurs in different blocks, a PCA or DE is faulty.

7.2.4

Sense data (5-2x-xx), (B-44-xx), (B-47-xx), (B-4B-xx) and (B-4E-00): interface error

Sense data (5-2x-xx), (B-44-xx), (B-47-xx), (B-4B-xx) and (B-4E-00) indicate one of the following

symptoms:

•

An invalid or unsupported command was issued, or invalid or unsupported parameters were

specified.

•

An interface error occurred.

A hardware error occurred inside HDDs.

If this error occurs, the PCA or the interface is faulty.

7-4

C141-E230

Glossary

Additional Sense Code

This is a 1-byte code displayed in the sense data and is information which

specifies the type of error that was detected.

CCS

Common Command Set

This is the standard form of SCSI logical specifications stipulated by the

operations subcommittee of the American National Standards Institute (ANSI)

which stipulates functions which a direct access device (magnetic disk, etc.)

should support.

CDB

Command Descriptor Block

A series of data which describes commands related to input/output operations,

sent from the initiator to the target.

Command

Initiator (INIT)

SAS Device

SCSI

This is a command to a target to perform an input/output operation, and it is

described as the CDB.

This is an SAS device which initiates input and output operations on the SAS bus.

In this manual, initiator has been abbreviated to "INIT."

The general name given to a device which is connected to the SAS bus

(input/output device, I/O controller, host adapter, expander, etc.).

Small Computer System Interface

The standardized input/output interface of the American National Standards

Institute (ANSI). [Standard No.: ANSI X3. 131-1986]

Sense Data

When several items of error information are included in a command's completion

status, this is information generated by the target for reporting detailed

information on that status.

Sense Key

Status

This is a 4-bit code displayed in the sense data. It contains information for

classifying the type of error that was detected.

This is 1 byte of information reported to the initiator by the target device when

execution of each command is completed, which displays the command's

completion state.

C141-E230

GL-1

Glossary

Target (TARG)

This is the SAS device that executes the input/output operations initiated by the

initiator (INIT). In this manual, target is abbreviated "TARG."

GL-2

C141-E230

Acronyms and Abbreviations

Alternating Current

ECC

EER

Error Correction Code

Enable Early Recovery

ACK

AEN

ALT

ACKnowledge primitive

Asynchoronous Event Notification

ALTernated (block)

EVPD Enable Vital Product Data

ARRE Automatic Read Reallocation

Enabled

ASCII American Standard Code for

Information Interchange

FIFO

Frame Ground

First In First Out

ASG

ASiGned block

FmtData Format Data

FOV

FUA

AWG American Wire Gauge

AWRE Automatic Write Reallocation

Enabled

Format Options Valid

Force Unit Access

G list

Gap

bpi

bits per inch

Grown defect list

BytChk Byte Check

HDC

HDD

Height

Hard Disk Controller

Hard Disk Drive

C list

CCS

CDB

Target Certification list

Common command set

Common descriptor block

Customer Engineer

HSEC Hard SECtor

CmpLst Complete List

CRC

CYL

Cyclic Redundancy Check

CYLinder

ILBN

IDentifier

Ideal Logical Block Number

Immed Immediate

INDX/SCT INDeX/SeCTor

Depth

Data Defect List

Disable Block Descriptor

Direct Current

Initialization Pattern

InterSector Gap

D list

DBD

ISG

DCR

Disable Correction

DCRT Disable CeRtificaTion

LBdata Logical Block data

DEF

Disk Enclosure

DEFective block

LBN

LED

LUN

LSI

Logical Block Number

Light Emitting Diode

Logical Unit Number

DevOfl Device Offline

DPO Disable Page Out

DPRY Disable PRimarY

Large-Scale Integrated circuit

DSP

Disable Saving Parameters

DTDC Data Transfer Disconnect Control

DTE

Disable Transfer on Error

C141-E230

AB-1

Acronyms and Abbreviations

MPU

MicroProcesser Unit

Magnetro Resistive

Multiple Select

TPI

TRM

Transfer Block

Tracks Per Inch

TeRMinator

NACK Negative ACKnowledge primitive

UnitOfl Unit Offline

OEM

Original Equipment Manufacturer

VCM

VPD

Voice Coil Motor

Vital Product Data

Vendor Unique

P list

P/N

Primary defect list

Parts/Number

PBdata Physical Block data

PC boardPrinted Circuit board

WCE

Width

PCA

PER

Printed Circuit Assembly

Post ERror

Page Format

Write Cache Enable

Write Protect

WWN World Wide Name

PLO Sync Phase Lock Oscillator Syncronous

PMI Partial Medium Indicator

PR4ML Partial Response class 4 Maximum

Likelihood

RCD

RMB

RSV

Read Continuous

Read Cache Disable

Relative Humidity

ReMovaBle

ReSerVed

S/N

Serial/Number

SAS

SBd

SBi

SCSI

SCT

Serial Attached SCSI

Synchronized Byte data area

Synchronized Byte identifier area

Small Computer System Interface

SeCTor

SelfTest Self Test

SPR

Signal Ground

Save Page

SPaRe block

Servo

SSEC Soft SECtor

STPF SToP Format

SURF SURFace

AB-2

C141-E230

Index

defect management....................................... 3-10

defective block slipping.................................. 1-4

delivery........................................................... 5-2

diagnosis......................................................... 1-4

diagnostic........................................................ 6-1

diagnostic test ............................................... 6-10

diagnostics and maintenance .......................... 6-1

dimension ....................................................... 4-1

disk ................................................................. 1-5

disk drive replacement.................................... 6-7

disk read error................................................. 7-4

dismounting drive......................................... 5-10

dual SAS port support..................................... 1-2

actuator........................................................... 1-5

additional error recovery parameters.............. 5-8

allowable input voltage and current................ 4-7

alternate area................................................... 3-9

alternate block allocation.............................. 3-10

alternate block allocation by REASSIGN

BLOCKS command................................ 3-12

alternate block allocation during

FORMAT UNIT command execution .... 3-11

alternate spare area ......................................... 3-4

automatic alternate block allocation............. 3-13

automatic alternate block allocation at

read operation ......................................... 3-13

automatic alternate block allocation at

write operation ........................................ 3-13

automatic alternate block reassignment.......... 1-3

ECC ................................................................ 3-7

environmental magnetic field ......................... 4-6

environmental specification............................ 2-4

environmental temperature............................. 4-5

error analysis................................................... 7-1

error analysis information collection.............. 7-1

error information indicated with sense

data............................................................ 7-3

error rate ......................................................... 2-5

error recovery ................................................. 1-3

error recovery during self-diagnostic.............. 6-3

error recovery parameter ................................ 5-8

basic operation test ......................................... 6-4

BCRC ............................................................. 3-7

block address of user space ............................ 3-9

block descriptor .............................................. 5-5

cache feature................................................... 1-2

caching parameter........................................... 5-9

changing revision number in field.................. 6-8

checking at abnormal end............................... 5-5

checking initial operation ............................... 5-4

checking operation after installation and

preparing HDD for use ............................. 5-4

command queuing feature .............................. 1-3

compactness.................................................... 1-1

connection requirement .................................. 4-8

connector location .......................................... 4-8

continuous block processing........................... 1-2

control mode parameter.................................. 5-9

controller circuit ............................................. 1-5

current waveform ........................................... 4-7

cylinder configuration .................................... 3-1

factory maintenance........................................ 6-7

field maintenance............................................ 6-7

finding possibly faulty part........................... 6-14

format capacity ............................................... 3-8

format parameter......................................5-5, 5-6

FORMAT UNIT command ............................ 5-6

formatting ....................................................... 5-5

function specification ..................................... 2-2

gap .................................................................. 3-7

general note .................................................... 5-1

hardware function test .................................... 6-2

hardware specification.................................... 2-1

hardware structure .......................................... 1-5

head................................................................. 1-5

high speed positioning.................................... 1-4

high-speed data transfer.................................. 1-2

data field......................................................... 3-7

data format...................................................... 3-1

data security at power failure.......................... 2-6

data space ....................................................... 3-1

defect list ...................................................... 3-10

C141-E230

IN-1

Index

outline of troubleshooting procedure............6-11

indicating revision number at factory

shipment....................................................6-8

initial diagnosis at time of power-on ..............5-4

initial seek operation check...........................6-10

initial self-diagnostic.......................................6-2

installation.......................................................5-1

installation requirement ..................................4-1

installation/removal/replacement....................5-2

interface connector..........................................4-9

interface connector (SAS plug) signal

allocation.................................................4-10

interface error .................................................7-4

interface test....................................................6-4

internal test space............................................3-3

packaging........................................................5-2

PAD ................................................................3-7

page code = 1..................................................5-8

page code = 3..................................................5-5

page code = 7..................................................5-8

page code = 21................................................5-8

part replacement..............................................6-7

part that can be replaced in field.....................6-6

physical sector allocation................................3-5

PLO Sync........................................................3-7

port address.....................................................5-3

port addressing................................................1-6

port control parameters .................................5-10

positioning error rate.......................................2-5

power on/off sequence....................................4-7

power supply requirement ..............................4-7

precaution .......................................................6-5

preventive maintenance ..................................6-6

programmable data block length.....................1-3

large capacity..................................................1-4

leakage magnetic flux.....................................4-6

limitation of bottom-mounting .......................4-3

limitation of side-mounting ............................4-3

logical data block addressing..........................3-8

low noise and low vibration............................1-4

low power consumption..................................1-4

random/sequential read test.............................6-4

read/write circuit.............................................1-5

read/write error recovery parameter................5-8

ready LED output signal...............................4-11

reliability.........................................................2-5

reporting result of self-diagnostic and

error indication..........................................6-3

reserve and release function............................1-3

responses to operation errors ..........................5-4

restriction of use of hazardous substance........1-1

revision number ..............................................6-7

maintenance information ................................6-5

maintenance level ...........................................6-7

maintenance requirement................................6-6

maximum temperature....................................4-5

microcode downloading..................................1-4

MODE SELECT/MODE SELECT

EXTENDED command.............................5-5

model name and order number .......................2-1

mounting drive................................................5-3

mounting frame structure................................4-3

mounting orientations.....................................4-2

mounting procedure........................................5-3

mounting requirement.....................................4-1

mounting screw...............................................4-3

MTBF .............................................................2-5

MTTR .............................................................2-6

multi-segment data buffer...............................1-2

SAS standard...................................................1-2

sector format ...................................................3-6

seek test...........................................................6-2

self-diagnostic.................................................6-1

SEND DIAGNOSTIC command....................6-3

sense data........................................................7-1

1-1x-xx .................................................... 7-4

3-0C-03.................................................... 7-4

3-1x-xx .................................................... 7-4

4-32-01 .................................................... 7-4

4-40-xx .................................................... 7-4

4-44-xx .................................................... 7-4

4-C4-xx.................................................... 7-4

5-2x-xx .................................................... 7-4

B-44-xx.................................................... 7-4

B-47-xx.................................................... 7-4

B-4B-xx ................................................... 7-4

noise filter.......................................................4-8

note on handling drive ....................................5-1

note on mounting............................................4-3

online self-diagnostic......................................6-3

operation check.............................................6-10

operation test.................................................6-10

IN-2

C141-E230

Index

B-4E-00....................................................7-4

E-1D-00....................................................7-4

sense data analysis.......................................... 7-3

sense key, additional sense code, and

tool and test equipment................................... 6-8

track format .................................................... 3-5

track skew and head skew............................... 3-5

troubleshooting at repair site ........................ 6-13

troubleshooting procedure............................ 6-11

troubleshooting with disk drive

additional sense code qualifier.................. 7-1

sequential starting of spindle motor................ 4-7

service clearance area..................................... 4-6

service life ...............................................2-6, 6-6

service system and repair................................ 6-6

setting ............................................................. 5-3

setting parameter ............................................ 5-7

spare disk drive............................................. 5-10

specification.................................................... 2-1

specifying CDB .............................................. 5-6

spindle motor.................................................. 1-5

standard feature .............................................. 1-1

start/stop of spindle motor.............................. 1-4

storage ............................................................ 5-2

sync mark ....................................................... 3-7

system configuration ...................................... 1-6

system space................................................... 3-3

replacement in field................................. 6-11

troubleshooting with part replacement in

factory ..................................................... 6-14

unpackaging.................................................... 5-2

unrecoverable error rate.................................. 2-5

user space........................................................ 3-3

vent hole ......................................................... 4-4

verify error recovery parameter...................... 5-8

verifying disk drive operation......................... 5-4

verifying interface connection........................ 5-4

test .................................................................. 6-9

test program.................................................... 6-4

write/read test ................................................. 6-2

C141-E230

IN-3

This page is intentionally left blank.

Comment Form

We would appreciate your comments and suggestions regarding this manual.

Manual code

Manual name

C141-E230-01EN

MAY2073RC, MAY2036RC

HARD DISK DRIVES PRODUCT/MAINTENANCE MANUAL

Please mark each item: E(Excellent), G(Good), F(Fair), P(Poor).

General appearance

Technical level

Organization

Clarity

(

)

Illustration

Glossary

Acronyms & Abbreviations

Index

(

)

Accuracy

Comments & Suggestions

List any errors or suggestions for improvement.

Page

Line

Contents

Please send this form to the address below. We will use your comments in planning future editions.

Address: Fujitsu Learning Media Limited

37-10 Nishikamata 7-chome

Oota-ku

Tokyo 144-0051

JAPAN

Fax: 81-3-3730-3702

Organization:

Name:

C141-E230-01EN

This page is intentionally left blank.

Nokia 3210 User Manual
Nespresso Coffeemaker TK70N01GB User Manual
JVC KD G305 User Manual
Hitachi Travelstar 13G1583 User Manual
Elta 4556 User Manual
Elmo Computer Drive 1 User Manual
Dell DR4000 User Manual
DCS Clock dCS Verona Master Clock User Manual
CMS Products 676 User Manual
Addonics Technologies HDMU3 User Manual