Operating Instructions
Mode d’emploi
A
B
C
D
E
F
Instrucciones de funcionamiento
Bedienungsanleitung
Bedieningsinstructies
Istruzioni sul funzionamento
Models:
PS60
PS60CC
PS70
DM-C
DM-4
DM-6
PS75
PS80
Safety & Maintenance of PS60CC, PS80, DM-C
The PS60CC, PS80, DM-C cross cut shredder creates small particles that, if allowed to accumulate, cause
the shredder to jam. Follow these simple precautions to significantly reduce the likelihood that particles will
accumulate and to keep your cross cut shredder operating at peak efficiency:
Parts Identification
1. Power Jack or Power Cord
2. Power Switch
4. Paper Entry
5. Wastebasket
3. Housing
6. Indicator Lights (on select models)
• Do not allow the basket to overfill. The power of this shredder will compress paper particles into the
basket even when it is full. The life of your shredder may be reduced if the cutting system continues to
operate with particles packed around it.
• Reverse the shredder often. Reversing helps the shredder flush out small cut particles. Empty basket if it
is full before reversing.
1
2
6
3
4
Oil the cutters:
When...
• Every second or third time you empty the basket;
• If the shredder’s cutting capacity is diminished;
• If the cutting cylinders stop with a squeak or a rubbing sound after power is removed.
How...
Use Powershred Lubricant #35250 or a suitable alternative with an extension nozzle. Alternatives can be
3 in 1 or Sewing Machine Oil. Oil must be non-flammable material and a non-degreaser! Do not use a can
spray. Accelerants are combustible. See order form in this manual.
1
6
5
A
B
C
D
E
F
A
B
C
D
E
F
4
2
Squeeze the lubricant across the full width of the cutters and then turn the machine on and run the cutting
system forward for a few seconds. (Cross-cut machines with auto start: block the photo eye with a piece of
paper in order to run the cutting system forward).
3
PS60, 60CC, DM-C, DM-4, DM-6
Then, depress the reverse button and run the cutting system for a few seconds. Repeat the procedure.
Safety of PS60CC, PS80, DM-C
• Do not operate PS60CC, PS80, DM-C without the basket it was shipped with.
• Do not attempt to defeat the safety interlock switch.
• PS 80 only: Do not use without the safety flap. Injury may result.
5
Paper Jams
1. Immediately return power switch to OFF (O) position.
PS70, PS75, PS80
2. Depress power switch to the REVERSE (R) position until the jammed paper has been
fully removed from the cutter.
3. DO NOT PULL ON PAPER. Damage to the drive system could occur.
All
4. If the REVERSE (R) function will not operate when pressed, the internal overload
protection device has been activated. Release the power switch from the REVERSE (R)
POSITION, wait 15 seconds and repeat.
Models
Overload Protection
Important Note
This shredder is protected by a built-in thermal
overload device that serves to protect the motor
from overuse. When continuous shredding is
conducted for an extended period of time, the
shredder will automatically turn itself off to cool
down. When shredding is automatically stopped,
This paper shredder is not intended to shred high
volumes of paper. Please refer to the specifications
for the recommended daily usage and sheet
capacity of this shredder. Please note that if the
paper is wider than the entry, and you fold it to fit,
the paper thickness increases and the recommended
5. In the machine jams in reverse, unplug the unit and cut all excess paper off the top
and bottom of the machine before repeating the jam-clearing procedure.
6. Shred smaller quantities. See sheet capacity (Table A).
allow the unit to stand for about 30 minutes before capacity may be exceeded.
using it again.
4
5
Specifications:
Declaration of Conformity
Fellowes Manufacturing Company
Shredding Speed = 20fpm (6m/ min)
Shred Size:
Doncaster Road, Kirk Sandall
Doncaster, South Yorkshire, DN31H England
Power Source:
120V-60Hz (N. America)
PS60CC, PS80, DM-C
5/ 32” x 4/ 5” (3.9mm x 20mm)
240V-50Hz (Australia)
230V-50Hz (U.K., Europe)
100V-50/ 60HZ (Japan)
6 Feet (1.9 meters)
declares that the product
Models PS60, PS60CC, PS70, PS75 and PS80,
conforms with the requirements of the Low Voltage Directive (73/ 23 EEC) and the Electromagnetic Compatibility
Directive (89/ 336 EEC) and the following harmonized European Normes (EN Standards) and IEC Standards.
All others
7/ 32” (5.8mm) strip
Power Cord:
Recommended daily use 50-75 sheets
Safety: EN60950 ‘Information Technology Equipment’
Model
PS60
PS60CC
DM-C
DM-4
DM-6
PS70
PS75
PS80
Entry Width
Dimensions
Weight
EMC:
Standard
EN 55104:1995
Severity Level
NA
Performance Criteria
NA
B
A
9"
(230mm)
17” x 14 3/ 8” x 10”
(432 x 365 x 254 mm)
20 lbs.
(9.1 kg)
EN 61000-4-2:1995
ENV 50141:1993
EN 61000-4-6: 1996
EN 61000-4-4:1995
ENV 50142:1994
EN 61000-4-5:1995
EN 61000-3-2:1995
EN 61000-4-11: 1995
4kV Contact, 8kV Air
3V, 150 kHZ to 230 Mhz 80%
1kHz Modulation
1kV, 5/ 50ns, 5kHz, AC Mains
1kV Differential Mode (Line-Line)
2kV Common Mode (Line-Gnd)
Table 1 Limits
10ms Dropout, 200ms 60%
Variation, 1 sec 30% Variation
Household limits
B
B
9 1/ 2"
(241mm)
20 3/ 4” x 16 1/ 2” x 10”
(527 x 419 x 279 mm)
28 lbs.
(12.7 kg)
A
B
C
D
E
F
A
B
C
D
E
F
NA
C
Limited Warranty
EN 55014:1993
NA
Fellowes Manufacturing Company warrants the cutting cylinders of all Fellowes shredders to be free
from defects in material and workmanship for five years from the date of purchase by the original
consumer. Fellowes warrants all other parts of the machine to be free of defects in material and
workmanship for one year from the date of purchase by the original consumer. If any part is found to be
defective during the warrant period, your sole and exclusive remedy will be repair or replacement, at
Fellowes’ option and expense, of the defective part.
Itasca, Illinois, USA
May 30, 1999
_____________________
Anthony Storrie
This warranty does not apply in cases of abuse, mishandling or unauthorized repair. ANY IMPLIED
WARRANTY, INCLUDING THAT OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, IS HEREBY
LIMITED IN DURATION TO THE APPROPRIATE WARRANTY PERIOD SET FORTH ABOVE. In no event shall
Fellowes be liable for any consequential or incidental damages attributable to this product. This warranty
gives you specific legal rights. You may have other legal rights that vary from state to state.
For more detail or to obtain service under this warranty, please contact Fellowes Customer Service
at 1-800-955-0959, Monday through Friday, 8 AM - 5 PM (Central Standard Time).
For specific instructions on obtaining service under this warranty on machines purchased outside the USA,
contact the appropriate location listed in the Contact for Service section of this instruction manual.
Warrantor: Fellowes Manufacturing Company.
6
7
Assembly Instructions / Instructions d'assemblage
/ Instrucciones de ensamblaje
Montage Anweisung / Montage instructies /
Istruzioni di assemblaggio
4
2
3
1
A
B
C
D
E
F
A
B
C
D
E
F
6
5
8
7
38
39
Contact For Service:
United States
Australia
1-800-955-0959
(In Melbourne) (03) 9330-3211
(Outside Melbourne) 1-800-331-177
1-800-665-4339
01302-885 331
+81-3-5496-2401
Canada
United Kingdom
Japan
Benelux
Italy
+31-(0)347-377988
+39-071730041
Germany
France
+49-5131-49770
+33-(0)4-72-08-25-45
1789 Norwood Avenue • Itasca, Illinois 60143-1095
630-893-1600 • Customer Service 1-800-955-0959
http://www.fellowes.com
®
Australia
Benelux
Canada
France
France
Germany
Italy
Japan
United Kingdom
Tullamarine, Vic.
Vianen, NL
Markham, Ont. Montanay
Rennes, I-L Garbsen, Han. Camerano, AN Tokyo
Doncaster, S. Yorks.
© 1999 Fellowes Printed in U.S.A. Part No. 35221
|