USER MANUAL
Remove fan housing by using thumbs to
unfasten clips and place fan in housing (Fig 5).
Snap fan housing back into the chassis.
Connect fan and speaker wiring to M/B as
instructed in M/B user manual
(After M/B is installed!).
Fig:5
Install 3.5" HDD and FDD (floppy)
A. Squeeze tabs on sides 3.5"
drive cassette (Fig.6) and pull
out to remove. Slide HDD into
cassette and fasten with coarse
thread flat head screws.
Fig:6
B. Slide floppy into the same
cassette and fasten with
fine thread flat head screws.
Install CD-ROM, (DVD or 5.25" FDD)
Fig:7
A. Fasten slide guides to the side of
CD-ROM (DVD or 5.25" FDD)
using fine thread flat head screws
(Fig 7).
B. Slide CD-ROM in to 5.25" bay and
snap in to place (Fig 8).
Fig:8
**Depending on M/B, you might have
To remove drive cassette**
A. Identify if M/B is AT, ATX or microATX.
B. Place chassis on its side with electronic
Bay in view (Fig. 9)
C. Using your choice of standoffs or stakes
to fasten M/B, prepare and screw into
Fig:9
mounting plate.
D. Make sure punch out holes for I/O ports
on the I/O plate are punched out matching
ports on the M/B.
E. Install at an angle, first by lining up the I/O
ports on the M/B with I/O plate. (Fig. 10)
F. Once holes are lined up, set M/B on
standoffs or stakes and make sure the
M/B is seated properly. (M/B mounting
screw holes vary with manufacturer.
Please refer to M/B user manual for
Fig:10
details.)
G. Fasten M/B using hex head screws.
H. Connect wiring as directed in M/B user
Manual.
Step 6. Install the power supply (P/S)
Slide into P/S area and fasten with hex head
screws (Fig. 11).
Fig:11
Three pc. Cover
Reinstall top cover making sure to line up
tabs on back (Fig.12). Then install side
panels by placing on rail guides (Fig.13),
and sliding towards back of chassis. Use
hex screws to fasten side panels in place.
Fig:12
Fig:13
One pc. Cover
To replace top cover, spread sides as
shown in (Fig. 14). Slide vertically down
and make sure slide fasteners guides are
properly set in the rails. Once top cover is
set properly on the rails, slide away from
you to close the top cover. Use hex head
screws to fasten top cover to chassis.
Fig:14
Snap into place, starting with
top snaps. Make sure tabs at top
of bezel are in place in holes at
top of chassis, then push lower
half of bezel into place
Fig:15
2
4
1
19
3
Option
3.5"HDD
5
6
20
18
7
9
8
17
16
15
14
11
13
12
10
Part List
EN-7230
SERIES
P/N
P/N:36110341
PART NAME
SUPPORT BRACKET
5.25 DRIVE BRACKET
CHASSIS
ADAPTER BRACKET(BABY AT,ATX)
ADAPTER PLATE
M/B MOUNTING PLATE
3.5 DRIVE BRACKET
COVER
CARD GUIDE BRACKET(A.B.S)
BEZEL(7230 ONLY)
CONTROL CONNECTOR(A)
POWER SWITCH HOLDER
3.5 EMI CLIP
NO
1
2
3
4
5
6
7
8
3213698
3213665
3213643
5207667
3214577
3213676
5208089
3213654
3131445
5103794
5404613
3132596
3212514
3131467
5404624
9
10
11
12
13
14
15
16
17
18
RUBBER FOOT
CONTROL CONNECTOR(B)
*32140541 I/O PLATE
*3406140
3401723
FAN (8CM)
SPEAKER
ITEM
NO:166,17
SERIES
P/N PART NAME
ARE
OPTIONAL
PARTS
EN-7230
ACCESSORY PARTS LIST
NO
A
B
C
D
E
F
G
H
5208012
3502573
3500851
3501171
3501592
3502549
3602055
3602102
SLIDE GUIDE
PCB SPACER
SCREW-PAN HEAD #6-32*5
SCREW-HEX HEAD #6-32
SCREW-PAN HEAD M3*5
STUD#6-32
POLYBAG 8*12
INNER BOX
|