AM/FM STEREO CLOCK RADIO
with COMPACT DISC PLAYER
POWER PANEL LOADING SYSTEM
and REMOTE CONTROL
(Model CKD2330 only)
OWNER’S MANUAL
CKD2328
CKD2330
(Without Remote Control)
(With Remote Control)
CKD2328_2330_B0901103.p65
36
11/9/2003, 14:17
Thank you… … … … … …
for purchasing this Emerson stereo clock radio with CD player and Power Panel
CD loading system. The motorized front panel rotates 90 degrees at the touch of a
button to make loading and unloading your CDs simple and easy. The Power Panel
loading system also means that this radio takes up less space on the bedside table
than other radios with drawer type CD loading systems.
In addition to the excellent sound from both the radio and the CD player this unit
also features a digital radio frequency display to make tuning your favorite stations
easier. There’s an automatic display dimmer that adjusts the brightness of the
clock and radio display to match the room lighting conditions. And there’s a two-
way snooze control to make it easier to grab those few extra minutes of sleep. You
can press the snooze button as usual or, if that’s too much of a task while you’re
half-asleep, you can just wave your hand in front of the radio to activate the snooze
function.
Of course there’s a batteryback up system to maintain your clock and alarm settings
in the event of a power interruption. And on model CKD2330 we’ve even included
a credit card size, 10-button remote control so you can switch the unit On and Off,
operate the CD functions, and adjust the volume from across the room.
This system was designed to give you many years of enjoyment with an absolute
minimum of care and maintenance. Please read this Owners Manual carefully and
completely to ensure that you get the maximum benefit from all the outstanding
features we have included in this product. If you encounter any problem with the
set up or operation of this model please do not return it to the retail store. Please
call the Emerson Customer Service Hotline toll free at 1-800-898-9020. One of
our service technicians will try to diagnose the problem for you.
Once again thanks for choosing this Emerson audio product.
For future reference, record the serial number in the space provided.
Model No: CKD2328/CKD2330
Serial No:
2
CKD2328_2330_B091103.p65
2
11/9/2003, 14:51
IMPORTANT NOTES
• Avoid installing this unit in places
• Operate controls and switches as
described in the manual.
exposed to direct sunlight or close to
heat radiating appliances such as
electric heaters, on top of other stereo
equipment that radiates too much heat,
places lacking ventilation or dusty areas,
places subject to constant vibration and/
or humid or moist areas.
• Before turning ‘On’ the power, make
certain that power cord is properly
installed.
• Store your CDs in a cool area to avoid
damage from heat.
• When moving the set, be sure to first
disconnect the power cord.
• Do not attempt to clean this unit with
chemical solvents as this might damage
the finish. Use a clean dry cloth.
CLASS 1 LASER PRODUCT
CAUTION
CLASS 1 LASER PRODUCT
APPAREIL Á LASER DE CLASSE 1
PRODUCTO LASER DE CLASE 1
INVISIBLE LASER RADIATION
WHEN OPENAND INTERLOCKS
DEFEATED.
AVOID EXPOSURE TO BEAM
This product contains a low power Laser Device.
FCC INFORMATION
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that
may cause undesired operation.
3
CKD2328_2330_B091103.p65
3
11/9/2003, 14:51
PREPARATION FOR USE
UNPACKING AND SETUP
• Carefully remove the main unit and the accessories from the display
carton. Remove all the packing material from the unit and verify that
you have the following items: Main unit, external AM antenna, and
remote control (for model CKD2330 only).
• Carefully remove any small strips of tape that may have been used to
prevent the Power Panel from moving in transit.
• Unwind the AC power cord and extend it to its full length.
• Unwind the lead wire FM antenna and extend it to its full length.
• This unit was shipped with a dummy CD transit card in the CD player.
This dummy CD prevents the laser pick up from moving during
shipment. This card must be removed before you can insert your own
CDs. However in order to remove the card the unit must be connected
to the AC outlet and the Power Panel must be opened electronically.
Please refer to the instructions on page 18 of this manual.
TO AVOID DAMAGING YOUR UNIT DO NOT ATTEMPT TO
MANUALLY OPEN THE POWER PANEL.
• Place the unit on a flat, level surface such as a table, desk, counter,
shelf, etc, convenient to a 120V 60 Hz AC outlet, out of direct sunlight,
and away from sources of excess heat, dust, moisture, or strong magnetic
fields.
4
CKD2328_2330_B091103.p65
4
11/9/2003, 14:51
External AM Antenna
This unit utilizes an external AM loop antenna instead of a built in ferrite bar antenna.
1.) Insert the small white plug from the AM loop antenna into the AM antenna jack
on the back of the radio. The plug can only be inserted one way.
2.) Attach the AM loop antenna to the antenna bracket on the back of the radio as
shown.
5
CKD2328_2330_B091103.p65
5
11/9/2003, 14:51
3.) Adjust the angle of the loop antenna until you find the position that provides the
best AM reception.
Note: If you find that AM reception is still unsatisfactory you can remove
the loop antenna from the antenna mounting bracket and attach it to the
wall with a thumbtack or small nail through the “keyhole” opening on the
antenna frame.
Hanging Screw
Key Hole
6
CKD2328_2330_B091103.p65
6
11/9/2003, 14:51
Battery Back Up System
This model includes a battery back up circuit that will maintain the clock and alarm
settings in the event of a temporary power interruption. The battery back up system
requires two “AA” batteries, not included. The battery compartment is located on
the bottom of the cabinet.
1.) Turn the radio upside down. Slide the battery door in the direction of the arrow
and remove the door.
2.) Insert two fresh “AA” alkaline batteries in the compartment. Be sure to observe
the polarity markings engraved in the compartment. If the batteries are inserted
incorrectly the back up system will not work.
3.) Replace the battery door and turn the radio right side up.
If the power is interrupted the display will go off and the radio will not work. However
the batteries will maintain the clock and alarm settings in memory. When the power
is restored the display will come on again and the clock and alarm settings will be
correct.
The life of the batteries will depend on the frequency and length of the power
interruptions that you experience. For best results we suggest you install fresh
batteries every 9 to 12 months. Always change both batteries together with a well-
known brand of alkaline batteries. Do not mix old and new batteries, or different
types of batteries such as alkaline and carbon-zinc batteries together.
7
CKD2328_2330_B091103.p65
7
11/9/2003, 14:51
Remote Control (Model CKD2330 Only)
Model CKD2330 includes a credit card size 10-button remote control that allows
you to operate the CD player, control the volume, and switch the system ‘On’ and
‘Off’ from across the room. The remote control operates on one, button-style lithium
battery (Type CR2032 or equivalent), included. We have placed a clear plastic
spacer between the battery and the battery contact plate so that the battery will
remain fresh until you are ready to use the remote. Pull on the end of the spacer
tab to remove the spacer from the remote and activate the battery.
Spacer
To use the remote control point the remote at the remote sensor on the front panel
of the radio and press the appropriate buttons on the remote. The effective operating
range of the remote is approximately 15 feet at an angle of no more than 15
degrees to the left or right of ‘dead center’.
When the remote control no longer works or the operation becomes intermittent it
is time to change the battery. Press downward on the locking tab and slide the
battery holder out of the remote as shown.
Remove the exhausted CR2032
battery from the holder, insert a fresh
battery into the holder with the “+” side
facing up, and slide the holder back
into the remote.
8
CKD2328_2330_B091103.p65
8
11/9/2003, 14:51
IMPORTANT BATTERY PRECAUTIONS:
• Do not leave the exhausted battery lying around where a child or pet might
play with or swallow it.
• If the battery is swallowed contact a physician immediately.
• Do not attempt to open the battery and do not dispose of the battery in a
fire.
PROTECT YOUR FURNITURE !!
This model is equipped with non-skid rubber 'feet' to prevent the product from
moving when you operate the controls. These 'feet' are made from non-migrating
rubber material specially formulated to avoid leaving any marks or stains on your
furniture. However certain types of oil based furniture polishes, wood preservatives,
or cleaning sprays may cause the rubber 'feet' to soften, and leave marks or a
rubber residue on the furniture. To prevent any damage to your furniture we strongly
recommend that you purchase small self-adhesive felt pads, available at hardware
stores and home improvement centers everywhere, and apply these pads to the
bottom of the rubber 'feet' before you place the product on fine wooden furniture.
9
CKD2328_2330_B091103.p65
9
11/9/2003, 14:51
POWER SOURCE
This radio is designed to operate on 120V 60Hz AC only. Attempting to operate
this radio on any other power source could cause damage to the unit and such
damage is not covered by your warranty.
Make sure the radio is connected to an AC outlet that is always “live”. Do not
connect the radio to an outlet that is controlled by a wall switch.
NOTE: This unit has a polarized AC plug with one wide blade and one narrow
blade. This plug will only fit into a matching polarized AC outlet. This is a safety
feature to reduce the possibility of electric shock. If this plug will not fit in your AC
outlet, you probably have an outdated non-polarized outlet. You should have your
outdated outlet changed by a qualified, licensed electrician. Do not file the wide
blade on the plug, or use an adapter to make the plug fit into your outlet. This
defeats the safety feature and could expose you to electric shock.
AC Outlet
AC Plug
10
CKD2328_2330_B091103.p65
10
11/9/2003, 14:51
LOCATION OF CONTROLS AND INDICATORS
3
5
7
FRONT PANEL
4
6
8
9
10
12
14
2
1
11
13
15
16
17
18
21 19
23
22 20
BACK PANEL
27
28 29
30
26
25
31
32
24
33
RIGHT SIDE PANEL
9
36
35
34
11
CKD2328_2330_B091103.p65
11
11/9/2003, 14:51
1.) CD Power Panel (Flashing Blue Light When Opening).
2.) Mute Indicator (Red).
3.) ALARM SET Button.
4.) Snooze Sensor.
5.) CLOCK SET Button.
6.) Display AUTO DIMMER.
7.) PROGRAM Button.
8.) LCD Display.
9.) TUNING Control.
10.) Remote Sensor.
11.) Reverse SKIP/Search
Button.
Button.
12.) PLAY/PAUSE
Button.
13.) Forward SKIP/Search
14.) STOP Button.
15.) REPEAT Button.
16.) OPEN/CLOSE
Button.
17.) Standby LED Indicator.
18.) STANDBY/ON
19.) SLEEP Button.
20.) MINUTE Button.
Button.
21.) VOL (Volume) UP/+ Button.
22.) VOL (Volume) DOWN/– Button.
23.) HOUR Button.
24.) AM Antenna Plug.
25.) AM Antenna Socket.
26.) AM Loop Antenna.
27.) SNOOZE Button.
28.) CD/RADIO Selector Switch.
29.) ALARM ON/OFF Button.
30.) ALARM MUSIC
31.) FM Wire Antenna.
32.) AC Power Cord.
/BUZZER
Switch.
33.) Backup Battery Compartment (Bottom Cabinet)
34.) Phones Jack.
35.) AM/FM/FM ST. Selector Switch.
36.) Right Speaker.
12
CKD2328_2330_B091103.p65
12
11/9/2003, 14:51
REMOTE CONTROL (Model CKD2330 Only)
5
6
7
4
3
8
9
2
1
10
11
1.) VOLUME – Button.
2.) MUTE Button.
3.) Reverse SKIP/SEARCH
Button.
4.) STOP Button.
5.) STANDBY/ON
6.) PLAY/PAUSE
7.) OPEN/CLOSE
8.) RANDOM Button.
Button.
Button.
Button.
9.) Forward SKIP/SEARCH
Button.
10.) VOLUME + Button.
11.) Battery Compartment (Back Cabinet)
13
CKD2328_2330_B091103.p65
13
11/9/2003, 14:51
OPERATING INSTRUCTIONS
• Make sure you have installed the back up batteries in the battery
compartment.
• Make sure you have installed the AM loop antenna and extended the FM
lead wire antenna to its full length.
• Make sure you have removed the remote control battery spacer from the
remote handset (Model CKD2330 only).
• Connect the AC power cord plug to a 120V 60Hz AC outlet.
SETTING THE CLOCK
When the radio is connected to the AC outlet for the first time the red Standby
indicator will come on and the main display will light.
The display will show AM hour
“12:00”. Do not press the
STANBY/ON
button. It is
easier to set the clock while the
unit is in the Standby mode
(Standby indicator is ‘On’).
1.) Depress and hold the CLOCK SET button and repeatedly press the HOUR
button to adjust the display to the correct hour, AM or PM.
2.) Continue to depress the CLOCK SET button and repeatedly press the MINUTE
button to adjust the display to the correct minute.
3.) When the display shows the correct time release all the buttons.
The display will show the correct time whenever the unit is in the Standby mode
(Standby indicator is ‘On’) or when the CD function is selected. To see the time
when the Radio function is selected press the CLOCK SET button.
14
CKD2328_2330_B091103.p65
14
11/9/2003, 14:51
SETTING THE WAKE-UP TIME
1.) Depress and hold the ALARM SET button. The display will change from clock
time to wake-up time and show “7:00 ”. Repeatedly press the HOUR button
to adjust the display to the correct wake-up hour, AM or PM.
2.) Continue to depress the ALARM SET button and repeatedly press the MINUTE
button to adjust the display to the correct wake-up minute.
3.) When the display shows the desired wake-up time release all the buttons.
To check the wake-up time just press the ALARM SET button at any time. The
display will show the wake-up time as long as the ALARM SET button is depressed.
15
CKD2328_2330_B091103.p65
15
11/9/2003, 14:51
LISTENING TO THE RADIO
1.) Slide the CD/RADIO selector switch, located on the top cabinet, to the RADIO
position.
2.) Press the STANDBY/ON
button on the front panel or the remote control
(model CKD2330 only) to turn the system ‘On’. The Standby indicator goes off
and an AM or FM radio frequency appears on the display.
3.) Select the desired band – AM, FM, or FM ST. – by sliding the Band selector,
located on the right side, to the appropriate position.
4.) Tune to the desired station by slowly rotating the TUNING control on the right
side. The digital frequency display will move up or down the band as you
rotate the tuning control. If you tune to an FM Stereo station the (((ST))) indicator
will appear in the display.
Note: This is a manual tuning radio with a digital frequency display. Slowly
rotate the TUNING control until you find the best reception, even if the
display does not indicate the exact frequency of the station.
5.) Press the VOLUME + or – buttons on the front panel or the remote control
(model CKD2330 only) to adjust the volume to the desired level.
6.) When you are finished listening press the STANDBY/ON
button on the
front panel or the remote control (model CKD2330 only) to return the system
to the Standby (Power ‘Off’) mode. The Standby indicator comes ‘on’ again
and the display changes from radio frequency to correct time.
16
CKD2328_2330_B091103.p65
16
11/9/2003, 14:51
Hints For Better Reception
FM – Adjust the position and direction of the FM lead wire antenna until you find
the position and direction that provides the best reception.
AM Loop Antenna
FM Wire Antenna
AM – Adjust the direction of the AM loop antenna that you connected to the back
of the radio. If this does not provide sufficient improvement try removing the loop
from the antenna bracket and moving it further away from the radio cabinet (as far
as the wire will allow). You may also attach the loop to the wall with a thumbtack or
small nail through the “keyhole” on the antenna frame.
17
CKD2328_2330_B091103.p65
17
11/9/2003, 14:51
PLAYING COMPACT DISCS
NOTE: Although this CD player can read CD-R and CD-RW discs, in addition to
normal CDs, the playability of CD-R and CD-RW discs may be effected by the type
of software that was used to create the discs, as well as the quality and condition of
the blank media you are using. 100% playability cannot be guaranteed. This is not
an indication of a problem with the player.
IMPORTANT: THIS MODEL HAS A MOTORIZED ELECTRONIC CD DOOR.
DO NOT ATTEMPT TO OPEN THE DOOR MANUALLY. THIS COULD CAUSE
DAMAGE TO THE DOOR OPENING MECHANISM.
1.) Slide the CD/RADIO selector switch on the top cabinet to the CD position.
2.) Press the STANDBY/ON
button on the front panel or on the remote control
(Model CKD2330 only). The display will show two flashing dashes (“- -“) in the
track number display.
After a few seconds the track number display will show “00”, indicating that
there is no disc in the player.
3.) Press the OPEN/CLOSE button on the front panel or on the remote control
(Model CKD2330 only) once.
IMPORTANT! THERE WILL BE A PAUSE OF APPROXIMATELY TWO
SECONDS BEFORE THE POWER PANEL OPENS. PLEASE WAIT. DO
NOT PRESS THE OPEN/CLOSE
BUTTON AGAIN.
18
CKD2328_2330_B091103.p65
18
11/9/2003, 14:51
4.) The Power Panel will rotate 90 degrees to allow you to load your disc in the
CD player. Before loading your own disc be sure to remove the dummy CD
transit card from the player and discard it.
5.) Place your disc on the center spindle with the printed label side facing you.
Gently press on the disc near the center hole to insure that the disc is properly
‘seated’ on the spindle.
6.) Press the OPEN/CLOSE button on the front panel or on the remote control
(Model CKD2330 only). The Power Panel will return to its closed position. The
disc will spin for a few seconds while the player reads the TOC (Table of
Contents) on the disc. Then the disc will stop spinning and the display will
show the total number of tracks on the disc.
19
CKD2328_2330_B091103.p65
19
11/9/2003, 14:51
7.) Press the PLAY/PAUSE
button on the front panel or on the remote control
(Model CKD2330 only). Playback begins on track 1 and the PLAY indicator
appears in the display.
PLAY
Adjust the VOLUME controls to the desired level.
8.) Playback will continue until the last track has played then the disc stops, the
PLAY indicator disappears, and the display again shows the total number of
tracks on the disc. To stop playback before the disc ends press the STOP
button on the front panel or on the remote control (Model CKD2330 Only) at
any time. The disc stops and the display shows the total tracks on the disc.
9.) If you are finished listening press the OPEN/CLOSE
button on the front
panel or on the remote control (Model CKD2330 Only), wait for the two-second
delay before the Power Panel opens. When the panel opens, gently remove
your disc from the player, and then press the OPEN/CLOSE
button again
to close the Power Panel.
10.) To listen to the radio slide the CD/RADIO selector switch back to the Radio
position, or press the STANDBY/ON
button to return the system to the
Standby (Power Off) mode.
20
CKD2328_2330_B091103.p65
20
11/9/2003, 14:51
PAUSE Control
To pause momentarily during CD playback press the PLAY/PAUSE
button on
the front panel or on the remote control (Model CKD2330 only) again. The sound
stops and the PLAY indicator flashes but the disc continues to spin.
PLAY
Press the PLAY/PAUSE
button again to cancel the Pause mode and resume
normal playback. The sound resumes at the same point on the disc and the PLAY
indicator stops flashing.
SKIP/SEARCH Controls (
/
)
During playback press the SKIP Forward
or SKIP Reverse
buttons on the
front panel or on the remote control (Model CKD2330 Only) repeatedly to skip
forward or back to higher or lower numbered tracks. Playback will start at the
beginning of the selected track.
To search within a track for a specific musical passage depress and hold the SKIP
Forward
or SKIP Reverse
buttons on the front panel or on the remote
control (Model CKD2330 Only). The player will search rapidly forward or backward
as long as the buttons are depressed. When you hear the desired passage release
the buttons and normal playback will resume at that point.
To start playback from a specific track load your disc as usual and wait until the
display shows the total number of tracks. Press the SKIP Forward
or SKIP
Reverse
buttons repeatedly until the desired track number appears in the display
then press the PLAY/PAUSE
button to begin playback on the desired track.
21
CKD2328_2330_B091103.p65
21
11/9/2003, 14:51
SPECIAL PLAYBACK MODES
REPEAT Playback
You can program the player to continuously repeat a single track or the entire disc.
The Repeat mode can be selected while the disc is playing or while the disc is
stopped.
Single Track Repeat
Select the track to be repeated and then press the REPEAT button on the front
panel once. The REPEAT indicator begins flashing in the display. If necessary,
press the PLAY/PAUSE
button to begin playback. The selected track will be
repeated continuously.
REPEAT PLAY
All Tracks Repeat
Press the REPEAT button on the front panel twice. The REPEAT indicator remains
in the display. If necessary, press the PLAY/PAUSE
button to begin playback.
The entire disc will be repeated continuously.
REPEAT PLAY
To cancel Repeat playback press the REPEAT button on the front panel until the
REPEAT indicator no longer appears in the display. Repeat Playback mode may
also be canceled by pressing the STOP button twice, switching to Radio function,
or pressing the STANDBY/ON
button to shut the power ‘Off’.
22
CKD2328_2330_B091103.p65
22
11/9/2003, 14:51
RANDOM Playback (Model CKD2330 Only)
When the Random Playback mode is selected all the tracks on the disc will be
played in random order. Random Playback mode can be selected while the disc is
playing or while the disc is stopped.
Press the RANDOM button on the remote control (Model CKD2330 Only). There
is no Random button on the front panel. The RANDOM indicator appears in the
display. If necessary, press the PLAY/PAUSE
button to begin playback.
PLAY
RANDOM
The player will randomly select a track and begin playback. After each track plays
once the player stops and the display again shows the total number of tracks on
the disc. However the RANDOM indicator remains in the display.
To cancel Random Playback press the RANDOM button again until the RANDOM
indicator disappears. Random playback may also be canceled by pressing the
STOP button twice, switching to Radio function, or pressing the STANDBY/ON
button to shut the power ‘Off’.
23
CKD2328_2330_B091103.p65
23
11/9/2003, 14:51
PROGRAMMED PLAYBACK
Use the Programmed Playback feature to play up to 20 tracks on a disc in any
desired order. You may also program a particular track to play several times within
a programmed sequence if desired.
NOTES:
(A.)You cannot program a disc while it is playing. Press the STOP button to
stop playback and then follow the programming steps below.
(B.)Programming is only possible with the front panel control. There is no
PROGRAM button on the remote control.
1.) Load your disc as usual and wait until the display shows the total number of
tracks on the disc.
2.) Press the PROGRAM button on the front panel. The PROGRAM indicator
and Program Memory number “01” begin flashing in the display.
PROGRAM
24
CKD2328_2330_B091103.p65
24
11/9/2003, 14:51
3.) Press the SKIP Forward
or SKIP Reverse
buttons to select the first
track number to be programmed. Example: Track number 7.
PROGRAM
When the desired track number appears in the display press the PROGRAM
button again. Track 7 is now entered in Program Memory number “01”. The
program memory number now advances to number “02” and continues flashing.
PROGRAM
4.) Repeat step 3, selecting a different track number each time until you have
entered up to 20 tracks in the program memory. To confirm the program after
you have entered the last track press the PROGRAM button once more. The
display will scroll through all the tracks you programmed in sequence.
5.) When you have completed programming the desired tracks press the PLAY/
PAUSE
button to begin programmed playback. The PLAY and PROGRAM
indicators appear in the display. Playback will begin on the first track you
programmed and will continue until the last programmed track has played.
PLAY
PROGRAM
25
CKD2328_2330_B091103.p65
25
11/9/2003, 14:51
6.) When the program is completed the player stops and the display again shows
the total tracks on the disc. However the PROGRAM indicator remains in the
display and the player remains in the Programmed Playback mode.
PROGRAM
If you press the PLAY/PAUSE
button the programmed sequence will play
again. To cancel the Programmed Playback mode press the STOP button
while the player is stopped. The PROGRAM indicator goes off. Programmed
Playback may also be canceled by switching to Radio function, or pressing
the STANDBY/ON
button to shut the power ‘Off’.
Programmed Repeat Playback
You may use the Programmed Playback and Repeat features together to
continuously repeat a programmed sequence. First program the desired sequence
according to steps 1 through 5 on pages 24-25. When Programmed Playback
begins press the REPEAT button twice to select the Repeat All Tracks mode. The
REPEAT indicator appears in the display together with the PROGRAM and PLAY
indicators. The programmed sequence will be repeated continuously.
REPEAT PLAY
PROGRAM
26
CKD2328_2330_B091103.p65
26
11/9/2003, 14:51
ALARM Function
You can use the alarm function to wake you to an electronic buzzer tone, the radio,
or your favorite CD.
First press the ALARM SET button on the front panel to check the Wake Up time
setting. Adjust the Wake Up time if necessary. Then press the ALARM ON/OFF
button on the top panel. The Alarm “On” indicator
appears in the display.
Wake To Buzzer
Press the STANDBY/ON
button to put the system in the Standby (Power ‘Off’)
/BUZZER switch on the top panel to the BUZZER
mode. Set the MUSIC
position. At the selected wake up time the buzzer will sound. It will continue for
one hour and then shut off automatically. To stop the alarm sooner press the
ALARM ON/OFF button once or STANDBY/ON
button on the front panel.
Wake To Radio
Tune to the desired radio station and adjust the volume to the level you want to
hear in the morning when the alarm comes on. Press the STANDBY/ON
button
to put the system in the Standby (Power ‘Off’) mode. Set the MUSIC
/BUZZER
switch on the top panel to the MUSIC
position. At the selected wake up
time the radio will turn on. It will continue for one hour and then shut off automatically.
To stop the radio sooner press the ALARM ON/OFF button once or STANDBY/
ON
button on the front panel.
27
CKD2328_2330_B091103.p65
27
11/9/2003, 14:51
Wake To CD
Load the desired CD, begin playback and adjust the volume to the desired level.
Press the STANDBY/ON
button to put the system in the Standby (Power ‘Off’)
/BUZZER switch on the top panel to the MUSIC
mode. Set the MUSIC
position. At the selected wake up time the CD will begin to play. It will continue for
one hour, or until the end of the disc, and then shut off automatically. To stop the
CD sooner, press the ALARM ON/OFF button once or STANDBY/ON
button
on the front panel.
Automatic Alarm Repeat
The Alarm will automatically repeat each day at the selected Wake Up time as
long as the Alarm indicator appears in the display. To cancel the alarm, press
the ALARM ON/OFF button on the top panel until the Alarm indicator
disappears.
Note: When the Alarm is turned “On”, the Standby LED indicator will flash.
28
CKD2328_2330_B091103.p65
28
11/9/2003, 14:51
SNOOZE Function
After the alarm turns on in the morning you can use the Snooze function to grab a
few more minutes sleep before the alarm sounds again. To activate the Snooze
function you can press the SNOOZE button on the top cabinet, or you can simply
wave your hand in front of the Snooze Sensor on the front panel.
The effective operating range of the Snooze Sensor is approximately 2 inches.
The Snooze function will stop the alarm for 5 minutes and then turn the alarm on
again. The Snooze operation can be repeated several times within one hour. But
after one hour the alarm will not turn on again.
Remote Snooze Operation (Model CKD2330 Only)
After the alarm comes on in the morning you may also activate the SNOOZE
function by pressing any button on the remote control EXCEPT THE STANDBY/
ON BUTTON. The alarm will stop for 5 minutes and then turn on again.
29
CKD2328_2330_B091103.p65
29
11/9/2003, 14:52
SLEEP TIMER (Front Panel Only)
This system includes a programmable Sleep Timer that allows you to fall asleep
from 59 minutes of music and then shuts the power ‘Off’ automatically.
To Operate The Sleep Timer:
1.) Turn the system ‘On’ and operate either the Radio or CD function as usual.
2.) Adjust the Volume level controls to the desired level. Remember that the level
you select for the sleep to music function is the same level you will hear when
the timer turns the system on in the morning.
3.) Press and hold the SLEEP button on the front panel. There is no SLEEP
button on the remote control.
4.) The display will show “0:59” indicating that the sleep timer will shut the power
off after 59 minutes. The SLEEP indicator flashes in the display. Continue
holding the SLEEP button to decrease the amount of Sleep Timer operation.
Release the SLEEP button when the display shows the desired amount of
Sleep time.
SLEEP
5.) The Sleep Time display disappears. The SLEEP indicator stops flashing. When
the Sleep Timer counts down to “00”, the power shuts off automatically.
SLEEP
30
CKD2328_2330_B091103.p65
30
11/9/2003, 14:52
NOTES:
• You can shut the unit off manually before the Sleep Timer counts down to “00”
by pressing the STANDBY/ON
button at any time. Or just cancel the Sleep
Timer by pressing the SNOOZE button.
• Remember that if you are falling asleep to CD you will also wake to CD, and if
you fall asleep to the radio you will also wake to the radio.
• If you are falling asleep to CD, the system will only operate until the CD ends.
If you set the Sleep Timer for 59 minutes but your CD is only 45 minutes long,
the music will stop after 45 minutes.
IMPORTANT:
When the SLEEP function is on, the Radio Frequency will always appear on
the display. The CLOCK SET and ALARM SET functions will be disabled,
you can still check the ALARM wake up time by pressing the ALARM SET
button, but pressing the CLOCK SET button has no effect during Sleep Timer
operation.
Power Failure During Sleep Timer Operation
If you experience a power failure during Sleep Timer operation an incorrect time
(such as "3545") may appear on the display. If this occurs please perform the
following steps to correct the time display:
1.) Press the STANDBY/ON
button to turn the system 'On'.
2.) Press the SLEEP button once.
3.) Press the STANDBY/ON
button again to turn the system 'Off'.
The time display will return to normal.
31
CKD2328_2330_B091103.p65
31
11/9/2003, 14:52
MUTE Function (Model CKD2330 Only)
To stop the sound from the speakers temporarily press the MUTE button on the
remote control handset. The Mute indicator light (red) comes on. The sound stops
but the unit remains ‘On’. Press the MUTE button again to cancel Mute function
and restore the sound. The Mute indicator light (red) goes off.
Display Dimmer
The brightness of the display is automatically adjusted for the room light conditions.
The display brightness will be reduced when the room lighting is tuned off so as
not to interfere with your sleep. The display will brighten automatically in daylight or
when the room lights are turned on again for better visibility.
Headphone
Jack
The Stereo Headphone Jack is located on the right side panel. Connect a set of
stereo headphones (not included) to this jack for private listening without disturbing
others. The internal speakers are automatically disconnected when headphones
are connected to the headphone jack.
IMPORTANT: When using headphones always set the volume control to a
low level before you put the headphones on. Then put the headphones on and
gradually increase the volume to a comfortable listening level.
32
CKD2328_2330_B091103.p65
32
11/9/2003, 14:52
CARE AND MAINTENANCE
COMPACT DISC CARE
•
To remove a disc from its storage case, press down on the center of the case
and lift the disc out, holding it carefully by the edges.
•
Fingerprints and dust should be carefully wiped off the disc’s recorded surface
with a soft cloth.Unlike conventional records, compact discs have no grooves
to collect dust and microscopic debris, so gently wiping with a soft cloth should
remove most particles. Wipe in a straight line from the inside to the outside of
the disc. Small dust particles and light stains will have absolutely no effect on
reproduction quality.
•
•
Clean the disc periodically with a soft, lint-free, dry cloth. Never use detergents
or abrasive cleaners to clean the disc. If necessary, use a CD cleaning kit.
Never write on or affix labels to the surface of compact discs.
CARE OF THE CABINET
If the cabinet becomes dusty wipe it with a soft dry dust cloth. Do not use any wax,
polish sprays, or abrasive cleaners on the cabinet.
CAUTION
Never allow any water or other liquids to get inside the unit while cleaning.
33
CKD2328_2330_B091103.p65
33
11/9/2003, 14:52
LIMITED WARRANTY
Emerson Radio Corp. warrants manufacturing defects in original material, including
original parts and workmanship, under normal use and conditions, for a period of
ninety (90) days from the date of original purchase in the U.S. With your dated
proof of purchase, we will provide repair service at no charge for labor and parts at
an authorized Depot Repair Facility, or replace the product in our discretion. For
repair or replacement, pack your unit in a padded box, enclose your check or
money order payable to Emerson Radio Corp. in the amount of $9.00 (not required
by California residents) to cover shipping and handling costs, and enclose a copy
of your proof of purchase. Send your unit to:
Emerson Radio Corp.
1901 Diplomat Drive.
Farmers Branch, TX 75234.
This warranty does not cover damage from negligence, misuse, abuse, accident,
failure to follow operating instructions, commercial use, rental, repairs by an
unauthorized facility, or products purchased, used, serviced or damaged outside
of the United States.
THIS WARRANTYGIVES YOU SPECIFIC LEGAL RIGHTS, ANDYOU MAY
ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
AU898M
TO FIND THE LOCATION AND PHONE
NUMBER OF YOUR NEAREST SERVICE
R
CENTER PERMITTED TO PERFORM
WARRANTY...
SERVICE
CALL TOLL FREE: 1-800-695-0098
FOR ADDITIONAL SET-UP OR OPERATING ASSISTANCE
PLEASE CALL:
1-800-898-9020
FOR CUSTOMER SERVICE, PLEASE WRITE TO:
Emerson Radio Corp.
Consumer Affairs Dept.
1901 Diplomat Drive,
Farmers Branch, TX 75234.
34
CKD2328_2330_B091103.p65
34
11/9/2003, 14:52
R
EMERSON
Part No.: 16-2911B
309-01
Printed in China
CKD2328_2330_B091103.p65
35
11/9/2003, 14:52
|