Denon DN M991R User Manual

MINIDISC RECORDER  
-
DN M991R  
OPERATING INSTRUCTIONS  
BEDIENUNGSANLEITUNG  
MODE D’EMPLOI  
INSTRUCCIONES DE OPERACION  
BRUKSANVISNING  
FOR ENGLISH READERS  
PAGE  
SEITE  
PAGE  
PAGINA  
SIDA  
006 ~ PAGE  
042 ~ SEITE  
077 ~ PAGE  
041  
078  
114  
FÜR DEUTSCHE LESER  
POUR LES LECTEURS FRANCAIS  
PARA LECTORES DE ESPAÑOL  
FÖR SVENSKA LÄSARE  
115 ~ PAGINA 150  
151 ~ SIDA 186  
1
SAFETY INSTRUCTIONS  
1.  
Read Instructions – All the safety and operating  
12. Power-Cord Protection – Power-supply cords should be  
routed so that they are not likely to be walked on or  
pinched by items placed upon or against them, paying  
particular attention to cords at plugs, convenience  
receptacles, and the point where they exit from the  
appliance.  
instructions should be read before the appliance is  
operated.  
2.  
3.  
4.  
5.  
Retain Instructions – The safety and operating instructions  
should be retained for future reference.  
Heed Warning – All warnings on the appliance and in the  
operating instructions should be adhered to.  
14. Cleaning – The appliance should be cleaned only as  
recommended by the manufacturer.  
Following Instructions – All operating and use instructions  
should be followed.  
15. Power Lines – An outdoor antenna should be located away  
from power lines.  
Water and Moisture – The appliance should not be used  
near water – for example, near a bathtub, washbowl,  
kitchen sink, laundry tub, in a wet basement, or near a  
swimming pool, and the like.  
16. Outdoor Antenna Grounding – If an outside antenna is  
connected to the receiver, be sure the antenna system is  
grounded so as to provide some protection against voltage  
surges and built-up static charges. Article 810 of the  
National Electrical Code, ANSI/NFPA 70, provides  
information with regard to proper grounding of the mast  
and supporting structure, grounding of the lead-in wire to  
an antenna-discharge unit, size of grounding conductors,  
location of antenna-discharge unit, connection to grounding  
electrodes, and requirements for the grounding electrode.  
See Figure A.  
6.  
Carts and Stands – The appliance should be used only with  
a cart or stand that is recommended by the manufacturer.  
6A. An appliance and cart  
combination should be  
moved with care.  
Quick stops, excessive  
force, and uneven  
surfaces may cause  
the appliance and cart  
combination to overturn.  
17. Nonuse Periods – The power cord of the appliance should  
be unplugged from the outlet when left unused for a long  
period of time.  
18. Object and Liquid Entry – Care should be taken so that  
objects do not fall and liquids are not spilled into the  
enclosure through openings.  
7.  
8.  
Wall or Ceiling Mounting – The appliance should be  
mounted to a wall or ceiling only as recommended by the  
manufacturer.  
19. Damage Requiring Service – The appliance should be  
serviced by qualified service personnel when:  
Ventilation – The appliance should be situated so that its  
location or position does not interfere with its proper  
ventilation. For example, the appliance should not be  
situated on a bed, sofa, rug, or similar surface that may  
block the ventilation openings; or, placed in a built-in  
installation, such as a bookcase or cabinet that may  
impede the flow of air through the ventilation openings.  
A. The power-supply cord or the plug has been damaged;  
or  
B. Objects have fallen, or liquid has been spilled into the  
appliance; or  
C. The appliance has been exposed to rain; or  
9.  
Heat – The appliance should be situated away from heat  
sources such as radiators, heat registers, stoves, or other  
appliances (including amplifiers) that produce heat.  
D. The appliance does not appear to operate normally or  
exhibits a marked change in performance; or  
E. The appliance has been dropped, or the enclosure  
damaged.  
10. Power Sources – The appliance should be connected to a  
power supply only of the type described in the operating  
instructions or as marked on the appliance.  
20. Servicing – The user should not attempt to service the  
appliance beyond that described in the operating  
instructions. All other servicing should be referred to  
qualified service personnel.  
11. Grounding or Polarization – Precautions should be taken so  
that the grounding or polarization means of an appliance is  
not defeated.  
FIGURE  
A
EXAMPLE OF ANTENNA GROUNDING  
AS PER NATIONAL  
ELECTRICAL CODE  
ANTENNA  
LEAD IN  
WIRE  
GROUND  
CLAMP  
ANTENNA  
DISCHARGE UNIT  
(NEC SECTION 810-20)  
ELECTRIC  
SERVICE  
EQUIPMENT  
GROUNDING CONDUCTORS  
(NEC SECTION 810-21)  
GROUND CLAMPS  
POWER SERVICE GROUNDING  
ELECTRODE SYSTEM  
(NEC ART 250, PART H)  
NEC - NATIONAL ELECTRICAL CODE  
3
SVENSKA  
ESPAÑOL  
FRANCAIS  
DEUTSCH  
ENGLISH  
NOTE ON USE / HINWEISE ZUM GEBRAUCH / OBSERVATIONS RELATIVES A LUTILISATION  
NOTE SULLUSO / NOTAS SOBRE EL USO / ALVORENS TE GEBRUIKEN / OBSERVERA  
OBSERVAÇÕES QUANTO AO USO  
Do not let foreign objects in the set.  
Keine fremden Gegenstände in das Gerät  
kommen lassen.  
Ne pas laisser des objets étrangers dans  
l’appareil.  
E’ importante che nessun oggetto è inserito  
all’interno dell’unità.  
No deje objetos extraños dentro del equipo.  
Laat geen vreemde voorwerpen in dit apparaat  
vallen.  
Keep the set free from moisture, water, and  
dust.  
Halten Sie das Gerät von Feuchtigkeit, Wasser  
und Staub fern.  
Protéger l’appareil contre l’humidité, l’eau et  
lapoussière.  
Tenete l’unità lontana dall’umidità, dall’acqua e  
dalla polvere.  
Mantenga el equipo libre de humedad, agua y  
polvo.  
Laat geen vochtigheid, water of stof in het  
apparaat binnendringen.  
Utsätt inte apparaten för fukt, vatten och  
damm.  
Mantenha o aparelho livre de qualquer  
umidade, água ou poeira.  
Avoid high temperatures.  
Allow for sufficient heat dispersion when  
installed on a rack.  
Vermeiden Sie hohe Temperaturen.  
Beachten Sie, daß eine ausreichend  
Luftzirkulation gewährleistet wird, wenn das  
Gerät auf ein Regal gestellt wird.  
Se till att främmande föremål inte tränger in i  
apparaten.  
Não deixe objetos estranhos no aparelho.  
Eviter des températures élevées.  
Tenir compte d’une dispersion de chaleur  
suffisante lors de l’installation sur une étagère.  
Evitate di esporre l’unità a temperature alte.  
Assicuratevi che ci sia un’adeguata dispersione  
del calore quando installate l’unità in un mobile  
per componenti audio.  
Evite altas temperaturas.  
Permite la suficiente dispersión del calor  
cuando está instalado en la consola.  
Vermijd hoge temperaturen.  
Zorg voor een degelijk hitteafvoer indien het  
apparaat op een rek wordt geplaatst.  
Undvik höga temperaturer.  
Se till att det finns möjlighet till god  
värmeavledning vid montering i ett rack.  
Evite temperaturas altas.  
Conceda suficiente dispersão de calor quando  
o equipamento for instalado numa prateleira.  
Do not let insecticides, benzene, and thinner  
come in contact with the set.  
Lassen Sie das Gerät nicht mit Insektiziden,  
Benzin oder Verdünnungsmitteln in Berührung  
kommen.  
Ne pas mettre en contact des insecticides, du  
benzène et un diluant avec l’appareil.  
Assicuratevvi che l’unità non venga in contatto  
con insetticidi, benzolo o solventi.  
No permita el contacto de insecticidas,  
gasolina y diluyentes con el equipo.  
Laat geen insektenverdelgende middelen,  
benzine of verfverdunner met dit apparaat in  
kontakt komen.  
Se till att inte insektsmedel på spraybruk,  
bensen och thinner kommer i kontakt med  
apparatens hölje.  
Não permita que inseticidas, benzina e  
dissolvente entrem em contacto com o  
aparelho.  
Unplug the power cord when not using the set  
for long periods of time.  
Wenn das Gerät eine längere Zeit nicht  
verwendet werden soll, trennen Sie das  
Netzkabel vom Netzstecker.  
Débrancher le cordon d’alimentation lorsque  
l’appareil n’est pas utilisé pendant de longues  
périodes.  
Disinnestate il filo di alimentazione quando  
avete l’intenzione di non usare il filo di  
alimentazione per un lungo periodo di tempo.  
Desconecte el cordón de energía cuando no  
utilice el equipo por mucho tiempo.  
Neem altijd het netsnoer uit het stopkontakt  
wanneer het apparaat gedurende een lange  
periode niet wordt gebruikt.  
Koppla ur nätkabeln om apparaten inte  
kommer att användas i lång tid.  
Desligue o fio condutor de força quando o  
aparelho não tiver que ser usado por um longo  
período.  
Handle the power cord carefully.  
Hold the plug when unplugging the cord.  
Gehen Sie vorsichtig mit dem Netzkabel um.  
Halten Sie das Kabel am Stecker, wenn Sie  
den Stecker herausziehen.  
Manipuler le cordon d’alimentation avec  
précaution.  
Tenir la prise lors du débranchement du  
cordon.  
Manneggiate il filo di alimentazione con cura.  
Agite per la spina quando scollegate il cavo  
dalla presa.  
Maneje el cordón de energía con cuidado.  
Sostenga el enchufe cuando desconecte el  
cordón de energía.  
Hanteer het netsnoer voorzichtig.  
Houd het snoer bij de stekker vast wanneer  
deze moet worden aan- of losgekoppeld.  
Hantera nätkabeln varsamt.  
Never disassemble or modify the set in any  
way.  
Versuchen Sie niemals das Gerät auseinander  
zu nehmen oder auf jegliche Art zu verändern.  
Ne jamais démonter ou modifier l’appareil  
d’une manière ou d’une autre.  
Non smontate mai, nè modificate l’unità in  
nessun modo.  
Nunca desarme o modifique el equipo de  
ninguna manera.  
Nooit dit apparaat demonteren of op andere  
wijze modifiëren.  
* (For sets with ventilation holes)  
Do not obstruct the ventilation holes.  
Die Belüftungsöffnungen dürfen nicht verdeckt  
werden.  
Ne pas obstruer les trous d’aération.  
Non coprite i fori di ventilazione.  
No obstruya los orificios de ventilación.  
De ventilatieopeningen mogen niet worden  
beblokkeerd.  
Håll i kabeln när den kopplas från el-uttaget.  
Manuseie com cuidado o fio condutor de  
energia.  
Ta inte isär apparaten och försök inte bygga  
om den.  
Nunca desmonte ou modifique o aparelho de  
alguma forma.  
Täpp inte till ventilationsöppningarna.  
Não obstrua os orifícios de ventilação.  
Segure a tomada ao desconectar o fio.  
4
ENGLISH  
DEUTSCH  
FRANCAIS  
ESPAÑOL  
SVENSKA  
REAR PANEL / RÜCKWAND /  
FRONT PANEL / FRONTPLATTE /  
PANNEAU AVANT / PANEL FRONTAL /  
FRAMSIDA  
PANNEAU ARRIERE / PANEL TRASERO /  
BAKSIDA  
DISPLAY WINDOW / DISPLAY-FENSTER / FENETRE D’AFFICHAGE /  
PANTALLA DE VISUALIZACION / DISPLAYFÖNSTER  
DIMENSIONS / ABMESSUNGEN / DIMENSIONS / DIMENSIÓNES / MÅTT  
133 mm  
(5-15/64”)  
13 mm  
(33/64”)  
401 mm (15-25/32”)  
144 mm (5-43/64”)  
90 mm (3-35/64”)  
18.5 mm (47/64”)  
5
ENGLISH  
MAIN FEATURES  
The DN-M991R MD recorder is a table-top type MD recorder designed for use in broadcast stations, for productions, etc.  
Recording Functions  
Auto Level Rec start  
This function automatically starts the recording operation when an audio signal level from an external unit connected to the DN-M991R exceeds  
the preset level (–36 to –66 dB, 6 steps) * You can turn off this function.  
Auto Track Increment  
DN-M991R detects the silent portion of the program material and automatically increases the track number. The level of the silent portion can  
be set within a range of –36 to –66 dB (6 steps).  
Stereo/Mono recording (74/148 min.)  
Playback Functions  
Using CUE Signals to make searches (Up to 5 points per track)  
Track Search Select knob (Easy track selection)  
Program Play (Max. 25 tracks)  
Program can be stored in the preset memory.  
Play mode and Finish mode  
1) Play mode q Continuous: Play a whole disc w Single: Play a track  
2) Finish mode (Stop, Next, Recue, Repeat)  
q Stop: Stop after finishing to play a track.  
w Next: Standby at the beginning of next track after finishing to play a track.  
e Recue: After finishing to play a track, standby at the beginning of the track.  
r Repeat: The tracks are repeated according to the play mode.  
Auto Cue  
After a track is selected it is automatically cued to the point where audio starts.  
Cueing tracks place at the point where audio starts rather than where the track starts. The level at which sound is first detected can be set  
between –36 to –72 dB (7 steps).  
End Monitor  
Pressing the END MON button during standby instantly previews the end of the track, thus assuring perfect “outros”. The point at which  
monitoring starts can be set within a range of 5 to 35 seconds (7 steps) prior to the track’s end.  
End Of Message (EOM)  
At the end of a track, the EOM flashes, providing a visual warning to the operator that the track will end shortly. The point at which the flashing  
begins can be set within a range of 5 to 35 seconds (7 steps) prior to the end of the track.  
Pitch Control (Preset) (+8.0 to –8.0 %, 0.1 step)  
Instant Start (Playback starts less than 0.01 seconds after the PLAY button is pressed.)  
Editing Functions  
Editing  
1) Basic Editing  
• DIVIDE: Smallest edited unit is 11.6 msec (1 sound group) • ERASE TRACK/ERASE DISC/ERASE CUE  
• COMBINE • MOVE • DISC’s Pitch • TRACK NAME • DISC NAME  
Up to 100 characters can be used for each name, however, the combined total number of characters cannot exceed 1700.  
2) Cue signals also can be edited. (Can be erased, rewritten, or added to later.)  
Undo function  
Undo function during editing (Up to 2 editing operations prior to the most recent one can be undone.)  
SCMS  
Recording is possible without reception of the copy defeat restriction. Writing of the copy defeat code is selectable.  
Functions for Systematization  
Rich Array of External Control Terminals  
Serial Remote. (RS232C/RS422A switchcable, D-sub 9 pin)  
Parallel Remote. (D-sub 25 pin)  
Easy operations from IBM-PCTM compatible keyboard  
• PS/2 keyboard connector is equipped on the rear panel.  
• Keyboard (PS/2 connector, US keyboard with 101 or 104 keys recommended) can be connected to perform playback, recording, program  
input, editing, hot start and other operations.  
Hot Start function (Parallel remote, serial remote, keyboard)  
• Hot start is possible for up to 10 tracks.  
• Tracks can be loaded into Hot Start by detecting the Auto Cue Level (–72/–66/–60/–54/–48/–42/–36 dB selectable in Preset mode).  
• Sound can be loaded into Hot Start from any track location.  
• Loaded tracks can be replaced with new tracks.  
• Seamless Loop can be used during Hot Start playback.  
• Hot Start operation is possible using parallel remote, serial remote or a keyboard (PS/2 connector, US keyboard with 101 or 104 keys  
recommended).  
Other Functions  
Large FL Display, Illuminated Button  
Sampling Rate Convertor  
• Digital input is possible at 32 and 48 kHz as well as 44.1 kHz.  
• If input occurs at 32 or 48 kHz, it is automatically converted to 44.1 kHz during recording.  
6
ENGLISH  
CONTENTS  
PART NAMES AND FUNCTIONS ……………………………8 ~ 11  
EDITING FUNCTIONS…………………………………………29 ~ 35  
,
z
(1) Front Panel ……………………………………………………8, 9  
(2) Rear Panel……………………………………………………9, 10  
(3) Display Window……………………………………………10, 11  
(1) Editing Functions ………………………………………………29  
(2) Editing Function Select ………………………………………30  
(3) Erasing Cue Signals ‹Cue erase function› …………………30  
(4) Erasing Tracks ‹Track erase function› ………………………31  
(5) Erasing All the Tracks on the Disc ‹All erase function› ……31  
(6) Dividing Tracks into Two Parts ‹Divide function›……………32  
(7) Combining Two Tracks ‹Combine function›…………………32  
(8) Moving Tracks ‹Move function› ………………………………33  
(9) Pitch on the disc (Disc’s pitch function) ……………………33  
(10) Inputting (Changing) Names ‹Title function› ………………34  
(11) Exit the Edit Mode or Undoing Editing ‹Undo functions› …35  
REMOTE CONTROL CONNECTIONS ………………………11, 12  
ABOUT MINIDISCS …………………………………………………12  
x
c
v
PRESET FUNCTIONS AND OPERATIONS …………………13 ~ 17  
(1) List of Preset Functions ………………………………………13  
(2) Presetting Procedure …………………………………………14  
(3) Detailed Description of Preset Functions ……………15 ~ 17  
BASIC OPERATION …………………………………………18 ~ 22  
(1) Starting Playback ……………………………………………18  
(2) End Monitor ……………………………………………………18  
(3) PLAY/PAUSE and STANDBY/CUE Operations ……………19  
(4) Before Starting to Record ……………………………………19  
(5) Method of Recording on Discs ………………………………19  
(6) Starting to Record ……………………………………………20  
(7) Stopping Recording ……………………………………………20  
b
CONNECTING AND OPERATING A KEYBOARD ……………36, 37  
(1) Connecting the Keyboard ……………………………………36  
(2) Keyboard Operations ……………………………………36, 37  
.
RESETTING THE MICROPROCESSOR …………………………38  
HANDLING CARTRIDGES …………………………………………38  
(1) Cautions on Handling …………………………………………38  
(2) Cautions on Storing ……………………………………………38  
(8) Starting Recording Automatically by  
Detecting the Input Level ……………………………………21  
MESSAGES …………………………………………………………39  
(9) Incrementing Track Numbers…………………………………22  
(10) Pre-UTOC Function ……………………………………………22  
SYSTEM LIMITATIONS ……………………………………………40  
(1) Track Number Limits …………………………………………40  
(2) Recording Time Limits ………………………………………40  
(3) Editing Function Limits ………………………………………40  
(4) Title Function Limits …………………………………………40  
(5) Other Limits ……………………………………………………40  
HANDY OPERATIONS ………………………………………23 ~ 25  
(1) Setting Cue Points ……………………………………………23  
(2) Direct Search for Cue Points …………………………………24  
(3) Instantaneous play (Hot Start) ………………………………25  
n
m
PROGRAMMED PLAYBACK …………………………………26 ~ 28  
(1) Inputting Programs ……………………………………………26  
(2) Changing Programs ………………………………………26, 27  
(3) Playing Programs ………………………………………………27  
(4) Presetting Programs …………………………………………28  
SPECIFICATIONS ……………………………………………………41  
Checking the Contents  
Check that the carton contains the following items:  
3P power supply cord ……………………………………………1 pc.  
Operating instructions (this booklet) ……………………………1 pc.  
Installing the Units  
Up to three units can be installed in a 19” EIA rack or console. Install shelves on the rack.  
NOTES:  
• To be ensure proper operation of the DN-M991R unit, set it so that  
the slant of its front panel is within 15° of the perpendicular.  
• The display window (fluorescent tube) is designed so that all  
indications can be seen from within the angles shown below. Install  
the units so that the visual angle is within this range.  
DECLARATION OF CONFORMITY  
We declare under our sole responsibility that this product, to which this declaration relates, is in  
conformity with the following standards:  
EN60065, EN55013, EN55020, EN61000-3-2 and EN61000-3-3.  
Following the provisions of 73/23/EEC, 89/336/EEC and 93/68/EEC Directive.  
7
ENGLISH  
1
PART NAMES AND FUNCTIONS  
(1) Front Panel  
Cartridge insertion slot  
• Insert the cartridge as indicated by the arrow on the top.  
• Once the cartridge is partially inserted.  
6 SEARCH and 7 SEARCH buttons  
• Use these buttons to change the play start position and for  
program operations.  
q
o
!
END MON/CLEAR button  
END MON (Normal mode)  
• Press this button in the standby mode to monitor the end of  
the track. (End Monitor)  
Display  
w
e
PROGRAM ON/OFF/LEVEL START button  
PROGRAM ON/OFF (Normal mode)  
• When this button is pressed while the PROGRAM IN button is  
lit, the program play mode is set.  
• The button lights during the program play standby and play  
modes.  
• The button lights when the end monitor mode is set.  
CLEAR (Edit mode)  
• The button is used for editing operation and for clearing  
characters.  
• When the button is pressed during the program play standby  
or play mode, the program play mode is cleared.  
STANDBY/CUE button  
!
• When this button is pressed during the play or pause mode,  
the pickup returns to the position at which playback started  
and the standby mode is set. (Back Cue)  
• When pressed during playback when the next track has been  
programmed, the programmed track is searched for and the  
standby mode is set.  
• The button lights when the standby mode is set.  
• When the button is pressed during the recording or recording  
pause mode, recording stops, the pickup returns to the  
recording start position and the standby mode is set.  
• When the button is pressed during the cue direct search  
mode, the cue point is searched.  
LEVEL START (REC mode)  
• When this button is pressed during the recording pause mode,  
the auto level start recording mode is set.  
• The button flashes when the auto level start recording mode is  
set.  
• When the button is pressed again, the auto level start  
recording mode is canceled.  
PLAY MODE switch  
• When this switch is turned, the play mode select.  
r
t
Select knob  
• Turn this knob to select the next track to be played.  
• Turn the knob clockwise by one click to move one track  
forward, counterclockwise by one click to move one track  
backward.  
• When the knob turned while pressing it in, one click  
corresponds to 10 tracks.  
• When the button is pressed while pressing the MODE button,  
the preset mode is set.  
PLAY/PAUSE button  
• Press this button in the standby, pause or manual search  
mode to begin playback.  
!
• Press the button in the stop mode to search for the first track  
and begin playback.  
• In the preset mode, use this knob to set and enter preset  
setting.  
• When the button is pressed in the recording pause mode,  
recording starts.  
• When setting programs, use this knob to select, enter and  
check the program.  
• The button lights when the play or recording mode is set.  
• When the button is pressed during playback, the pause mode  
is set. The button flashes while the pause mode is set.  
• When the button is pressed during recording, the recording  
pause mode is set. The button flashes when the recording  
pause mode is set.  
• In the cue point direct search mode, use this knob to select  
the cue point.  
• The editing mode is set when the knob is turned and pressed  
while selecting the editing function.  
REC button  
y
• When this button is pressed during the stop, standby or pause  
mode, the recording pause mode is set.  
• When the button is pressed during recording, the track  
number is incremented.  
• The button lights when the recording or recording pause mode  
is set  
DISP/CAPS/NUM button  
DISP (Normal mode)  
• When the button is pressed for over 0.5 seconds, the  
character display switches between the disc name, track name  
and date, in that order.  
• The date is only displayed when the date display is preset.  
(Refer to Page 13.)  
• When the button is pressed for less than 0.5 second, the time  
display switches between the remaining time (REMAIN) and  
elapsed time (ELAPSED).  
!
MODE button  
u
i
• Use this button to switch between the normal mode  
(recording and playback) and editing mode.  
• When pressed the STANDBY/CUE button while pressing this  
button, the preset mode is set.  
CAPS/NUM (REC, Edit mode)  
• When the button is pressed while editing names, the selected  
characters switch between capital letters, small letters,  
numbers and symbols, in that order.  
CUE SEARCH button  
• When this button is pressed during the standby, pause, search  
or play mode, the cue signal point direct search mode is set.  
When pressed again, the direct search mode is canceled.  
• The button lights when the direct search mode is set.  
PROGRAM IN/CUE WRITE button  
PROGRAM IN (Normal mode)  
!
• Press this button to set the program input mode.  
• The button will not function during the play mode.  
• The button flashes when in the program input mode.  
• The button lights when a program is set.  
8
ENGLISH  
CUE WRITE (REC, Edit mode)  
IN LEVEL L/R controls  
• Use these controls to adjust the level of the audio signals from  
the ANALOG IN connectors.  
@
@
@
• Press this button during the standby, pause, play, or manual  
search. When the edit mode and recording mode to record a  
cue signal.  
OUT LEVEL L/R controls  
• Use these controls to adjust the level of the audio signals from  
the ANALOG OUT connectors.  
EJECT button  
!
• Press this button to eject the cartridge.  
• The cartridge cannot be ejected during recording or while the  
UTOC is being written.  
DIGITAL OUT (AES/EBU) connector  
• This is an active balanced output using an XLR type connector.  
• Connect this connector to the balanced digital input connector  
on an amplifier or console.  
(2) Rear Panel  
RS232C/RS422A selector switch  
!
• Signal format: AES/EBU or SPDIF.  
• Use this to switch the serial remote connector signal between  
RS232C and RS422A according to the external controller’s  
signal.  
• Pin layout:  
1. Common  
2. Cold  
3. Hot  
• Applicable connector: Cannon XLR-3-31 or equivalent.  
• This unit uses a balanced digital output. A conversion circuit is  
necessary for connection to an unbalanced circuit.  
Example of balanced/unbalanced conversion circuit.  
74HCU04 ( 4 / 6 )  
RS232C/RS422A connector  
!
• This is a serial remote connector. A personal computer or  
other external controller can be connected to control the DN-  
M991R externally.  
• Applicable connector: 9-pin D-sub (female)  
• Baud rate: 9600 bps or 19200 bps  
• Pin layout:  
+5V  
100 µ  
16V  
+5V  
+
1
3
9
11  
13  
GND  
+5V  
+5V  
1SS270  
100 µ  
SN75157  
( 1 / 2 )  
74HCU04  
( 1 / 6 )  
14  
IN  
16V  
TO  
+
6
5
8
RS232C  
Signal name  
RS422A  
Signal name  
NC  
S.GROUND  
33µ 16V  
+
75Ω  
(
)
3
2
H
C
3
3
4
OUT  
DN-991R  
DIGITAL  
OUT  
(
)
7
4
110Ω  
Pin No.  
I/O  
I/O  
(
)
100P  
1
GND  
5 : 1  
1
6
2
7
3
8
4
9
5
NC  
NC  
O
I
O
O
I
MONITOR jack  
• Connect headphones with an impedance of 30 to 40 /ohms.  
@
@
x
x
x
x
x
T
D
D
T
T
R
R
D (RETURN)  
NC  
D
x
R
D
DIGITAL IN (AES/EBU) connector  
NC  
NC  
NC  
D (RETURN)  
I
• This is an active balanced input using an XLR type connector.  
• Connect this connector to the balanced digital output  
connector on an amplifier or console.  
NC  
NC  
NC  
S.GROUND  
• Signal format: AES/EBU or IEC958 Type I  
• Pin layout:  
1. Common  
2. Cold  
TERMINATOR switch  
• When set to the “ON” side, the serial remote connector’s pins  
are terminated internally.  
!
!
@
3. Hot  
• Applicable connector: Cannon XLR-3-32 or equivalent.  
• This unit uses a balanced digital input. A conversion circuit is  
necessary for connection to an unbalanced circuit.  
KEYBOARD connector  
• To use a keyboard, connect it to this connector.  
• The connector is a mini DIN type 6-pin connector.  
Example of unbalanced/balanced conversion circuit.  
ANALOG IN connectors  
• These are active balanced inputs using XLR type connectors.  
• Connect these connectors to the balanced analog output  
connectors on an amplifier or console.  
TO  
DN-991R  
DIGITAL  
IN  
• Pin layout:  
1. Common  
2. Hot  
3. Cold  
• Applicable connector: Cannon XLR-3-32 or equivalent.  
WARNING:  
Turn PITCH control OFF when making digital recording.  
Most digital recorders will not accept a variable pitched  
digital signal.  
ANALOG OUT connectors  
@
• These are active balanced outputs using XLR type connectors.  
• Connect these connectors to the balanced analog input  
connectors on an amplifier or console.  
• Pin layout:  
1. Common  
2. Hot  
3. Cold  
POWER switch  
• This turns the set on and off.  
@
@
• Applicable connector: Cannon XLR-3-31 or equivalent.  
NOTE: Do not short-circuit the hot or cold pin with the common  
AC inlet  
• Connect the included power cord here.  
pin.  
9
ENGLISH  
REMOTE connector  
@
• This is a parallel remote connector. Use it to control the DN-M991R with dry contact circuit connections.  
• Applicable connector: 25-pin D-sub (male)  
• Connector signal layout:  
Hot Start ON  
Signal name  
Hot Start OFF  
Signal name  
Pin No.  
Level  
I/O  
I/O  
1
FG  
O
I
FG  
O
I
14  
2
PLAY CODE 1 tally  
PLAY CODE 1 command  
PLAY CODE 2 tally  
PLAY CODE 2 command  
PLAY CODE 3 tally  
PLAY CODE 3 command  
PLAY CODE 4 tally  
PLAY CODE 4 command  
Tally common  
PLAY tally  
TTL (lol=20 mA)  
HCMOS (li–3 mA)  
TTL (lol=20 mA)  
HCMOS (li–3 mA)  
TTL (lol=20 mA)  
HCMOS (li–3 mA)  
TTL (lol=20 mA)  
HCMOS (li–3 mA)  
PLAY command  
PAUSE tally  
15  
3
O
I
O
I
PAUSE command  
STDBY/CUE tally  
STDBY/CUE command  
END CUE tally  
16  
4
O
I
O
I
17  
5
O
I
O
I
TRACK (+) command  
Tally common  
18  
6
O
I
I
PLAY CODE 5 command  
REPEAT command  
STOP command  
TRACK (–) command  
REC command  
HCMOS (li–3 mA)  
HCMOS (li–3 mA)  
HCMOS (li–3 mA)  
TTL (lol=20 mA)  
HCMOS (li–3 mA)  
TTL (lol=20 mA)  
PHOTO COUPLER  
+5 V, 20 mA  
19  
7
I
I
I
SEARCH (FWD) command  
CUE tally  
I
20  
8
REPEAT tally  
O
I
O
I
LOAD command  
LOAD tally  
SEARCH (REV) command  
REC tally  
21  
9
O
O
O
I
FADER START command  
Tally power supply  
FADER START return &  
Command common  
Reserved  
FADER START command  
Tally power supply  
Command common  
Command common  
REC E.O.M.  
22  
10  
23  
11  
24  
12  
25  
13  
O
O
I
(li=10 mA)  
Reserved  
E.O.M. tally  
DRY CONTACT  
Reserved  
Reserved  
Reserved  
E.O.M. tally  
DRY CONTACT  
Hot Start ON (Low)  
Hot Start OFF (High)  
HCMOS (li–3 mA)  
NOTES:  
• The tally output pin has open collector IC specifications (Imax. 20 mA, Vmax. 5 V), but the maximum supply current is 80 mA, so use with a  
total load current of 80 mA or less.  
• 13 Pin enable when Hot start (Preset 36)) set up off mode.  
(3) Display Window  
TRACK NO. indicator  
• This lights When the track number display shows the selected  
track number.  
CUE indicator  
#
#
#
• This lights for approximately 3 seconds when the position at  
which a cue signal is set is played.  
• The indicator flashes when the standby mode is set at a  
position at which a cue signal is set.  
PROGRAM indicator  
• This lights when the Program play mode is set.  
#
#
EOM indicator  
• This lights when the EOM is preset, and starts flashing when  
the EOM set time is reached.  
DISC NAME/TRACK NAME/DATE indicators  
• “DISC NAME” lights when the disc name is displayed on the  
character display, “TRACK NAME” lights when the track name  
is displayed, and “DATE” lights when the date is displayed.  
REPEAT indicator  
• When this indicator is lit, playback is repeated.  
#
$
EJECT LOCK indicator  
• When this indicator is lit, the eject lock function is set and the  
cartridge is not ejected even when the eject button is pressed.  
Level display  
• This displays the playback level during playback, the input level  
during recording.  
#
Character display  
$
$
EDIT indicator  
• This lights when the edit mode is set.  
#
#
• This displays disc names, track names and the date.  
• Various instructions are displayed here during presetting,  
programming, editing, etc.  
TOC indicator  
• This lights when it is necessary to rewrite the TOC (UTOC) due  
to editing, etc  
• This flashes while the TOC (UTOC) is being written.  
NEXT No. display  
• This displays the number of the next track to be played.  
• The program number is displayed during program input and  
editing.  
DIGITAL IN indicator  
#
• During recording, this indicates the digital input signal’s  
sampling frequency.  
• When the playback pitch is changed, the pitch value flashes for  
3 seconds.  
• This lights (or flashes) when the digital input signal is selected.  
• The indicator flashes when the digital signal is unlocked and  
remains lit when the digital signal is locked.  
10  
ENGLISH  
PITCH indicator  
• This lights, When the set play speed is set.  
PLAY MODE indicators  
• “SINGLE” lights when in the single track play mode.  
$
$
$
$
Playing time display  
• This indicates the time of the current position, in minutes (m),  
FS indicator  
• This lights when the sampling frequency is displayed on the  
seconds (s) and frames (f).  
NEXT number display.  
TRACK NO. display  
$
TIME MODE indicators  
• “ELAPSED” lights when the elapsed time is displayed.  
• “REMAIN” lights when the remaining time is displayed.  
$
• This displays the number of the track at the current position.  
This also lights during the track search mode and when  
switching to the standby mode.  
2
REMOTE CONTROL CONNECTIONS  
1. PARALLEL REMOTE  
(1) HOT START OFF (Preset 36))  
To control the DN-M991R remotely, refer to the example of remote control connections given below.  
The rating of REMOTE connector pin 22 (TALLY POWER SUPPLY) is +5 V, 80 mA maximum.  
Avoid currents in excess of the rating.  
(2) HOT START ON (Preset 36))  
Parallel hot key output command table  
Parallel hot tally output data table  
HOT START playback of the number selected according to the  
settings on the table below starts.  
The currently playing HOT START number is output according to the  
table below.  
PLAY CODE PLAY CODE PLAY CODE PLAY CODE PLAY CODE  
SW. No.  
PLAY TALLY PLAY TALLY PLAY TALLY PLAY TALLY PLAY TALLY  
SW. No.  
5
X
X
X
X
X
X
X
X
X
X
H
L
4
H
H
H
H
H
H
H
H
L
3
H
H
H
H
L
2
H
H
L
1
H
L
5
L
L
L
L
L
L
L
L
L
L
4
L
L
L
L
L
L
L
H
H
H
3
L
2
L
1
H
L
OFF  
9
1
2
L
H
H
L
8
H
L
3
L
H
L
7
L
4
H
H
H
H
L
6
H
H
L
H
L
5
L
H
L
5
L
6
H
H
L
4
L
H
L
7
H
L
3
L
L
8
2
H
H
X
H
H
H
X
H
H
L
9
L
L
H
L
1
L
10  
L
H
OFF  
10  
X
X
H
H
11  
ENGLISH  
(3) Relay Rec  
Multiple DN-M991R’s can be connected for relay playback.  
DN-M991R-1  
DN-M991R-2  
REMOTE  
REMOTE  
11  
REC E.O.M. tally  
2
11  
PLAY command REC E.O.M. tally  
The “Relay Red Mode” is set when anything but “OFF” is selected for “Preset RelayRec” 19).  
When a disc is loaded, the REC monitor mode is set automatically.  
Once recording on the first DN-M991R (DN-M991R-1) starts and the disc’s remaining recording time reaches the time specified with the  
presettings, an REC E.O.M. tally is output and recording starts on DN-M991R-2.  
Thus, it is possible to record continuously on multiple DN-M991R’s.  
NOTE: The REC E.O.M. tally is output even if an error occurs on the recording component and the component stops.  
2. SERIAL REMOTE  
When using this unit connected to a controller or personal computer, connect the remote connector (RS-232C/RS-422A) to the controller using a  
9-pin D-sub cable.  
(1) When using the serial remote with a bus connection.  
q Set the preset “Player ID” to “0 to 15”. (For the operation, see Page 13.)  
w Set the RS232C/RS422A selector switch of the rear panel to “RS-422A”. (For the operation, see Page 9.)  
e Set the TERMINATOR switch.  
TERMINATOR Switch  
RS232C/RS422A selector Switch  
Units connected midway through the bus connection:  
Set the TERMINATOR switch to “OFF”.  
Units connected at the end of the bus connection:  
Set the TERMINATOR switch to “ON”.  
RS232C / RS422A  
RS232C  
RS422A  
ON  
OFF  
(2) When using the serial remote 1:1 with controller.  
q Set the preset “Player ID” to “OFF”.  
w The RS232C/RS422A selector switch (a) of the rear panel can be used with either RS-422A or RS-232C.  
e Set the TERMINATOR switch to “ON”.  
3
ABOUT MINIDISCS  
2
MiniDiscs allow a maximum of 74 minutes (stereo) of recording and  
playback in a compact size.  
There are two types of MiniDiscs: those for playback only, and those  
for recording and playback.  
Recording on discs  
MiniDiscs include a section in  
which the audio signals are  
recorded and a section in which  
such data as track numbers and  
track titles are recorded.  
Playback only MiniDiscs  
• These discs are for playback only. Commercially  
available music MDs are of this type.  
• These are laser discs, like regular compact discs.  
• Tracks on such discs cannot be edited.  
Section in which track  
numbers and track titles  
are recorded (TOC)  
Section in which audio  
signals are recorded  
2
The TOC  
Recordable MiniDiscs  
With MiniDiscs, after the audio signals are recorded, data used for  
checking the tracks (TOC–Table of Contents) is also recorded on the  
disc. This TOC data is used when playing the disc. In addition,  
editing is performed by rewriting the TOC data.  
• These are magneto-optical discs on which both  
recording and playback are possible. Recording  
is performed through magnetic modulation.  
• Re-recording is also possible.  
TOC  
When TOC writing starts, the “  
” indicator flashes. Do not  
shake the main unit, press the main unit’s power button or unplug  
the power cord while the TOC is being written. If the data is not  
recorded properly, it will not be possible to play the disc.  
Accidental erasure prevention tabs  
These tabs protect recordable MiniDiscs from accidental erasure.  
To avoid accidentally erasing the recording, open the tab so that the  
hole is exposed. (See the diagram below.) When this is done,  
“Protected” is displayed if you attempt to record, erase or otherwise  
edit the disc, and the recording is protected. To record or erase the  
disc, set the tab back to its original position (with the hole covered).  
2
Handling MiniDiscs  
MiniDiscs are housed in cartridges, so there is no need to worry  
about dirt and scratches. However, dirty or warped cartridges may  
cause malfunction. Be careful of the following to ensure long-lasting,  
high quality sound:  
Hole exposed  
• Do not touch the disc surface directly.  
• Do not open the shutter by hand.  
• Do not place MiniDiscs in dusty, dirty or humid places.  
• Do not place MiniDiscs in places exposed to direct sunlight or high  
temperatures.  
Cleaning  
Use a dry cloth to gently wipe dirt or dust off the cartridge. Do not  
apply excessive force.  
12  
ENGLISH  
4
PRESET FUNCTIONS AND OPERATIONS  
(1) List of Preset Functions  
• Functions can be preset using the buttons on the front panel. These presettings are stored in a permanent memory, so they are not cleared  
even when the power is turned off.  
• The functions shown on the table below can be preset. Set the functions according to the usage purpose to efficiently achieve even higher  
quality playback.  
• One of the preset functions can be used to display information on this set (microprocessor version).  
Character display  
(as set upon shipment from  
factory)  
Classification  
grouping  
No.  
Preset function type  
Description  
AREA  
1
2
3
4
5
Preset area  
Play Finish mode  
Play sound  
Auto cue  
Selection of preset area  
Preset Area1  
Finish Next  
Stereo  
Play finish mode selection  
Selection of stereo or monaural playback  
Auto cue on/off setting start up level setting  
Selection of digital out format  
CueDet.OFF  
D.Out Pro  
Digital out  
Setting of whether or not to use the end monitor function and monitor time  
setting  
PLAYBACK  
6
End monitor  
End Mon.10s  
7
8
E. O. M.  
Setting of whether or not to display the EOM and display time setting  
Setting of delay playback start time  
E. O. M. 10s  
Delay OFF  
Pitch OFF  
Delay start  
9
Playback speed  
Play pitch auto  
Record input  
Stereo/Mono  
Selection of playback speed (–8.0 % ~ +8.0 % 0.1% step)  
Selection of whether or not to use pitch set for disc  
Selection of recording input (analog or digital)  
10  
11  
12  
PitchAutoOFF  
Analog IN  
Stereo recording or mono recording selection  
Rec Stereo  
Auto increment  
level  
13  
Auto increment level setting  
IncDet.–60dB  
14  
15  
16  
Auto increment  
Pre UTOC  
Auto increment selection  
Pre-UTOC on/off setting  
Recording start level setting  
AutoInc OFF  
Pre UTOC OFF  
RecLv –60dB  
RECORD  
Recording start level  
Recording start  
offset  
17  
18  
19  
20  
Recording start offset time setting  
RecOffsetOFF  
SCMS INH  
Copy management  
(SCMS)  
Serial copy management on/off selection  
Set the relay recording mode (on or off) and the timing for output of the REC  
E.O.M. tally when the relay recording mode is on  
Relay recording  
RelayRec OFF  
Next Stb.OFF  
Setting of whether or not to standby at the next track when the STANDBY/CUE  
button is pressed during playback  
Next track standby  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
31  
32  
33  
34  
35  
36  
37  
Play lock  
Selection of whether or not to inhibit the panel switches during playback  
Selection of whether or not to lock ejecting during playback  
Selection of whether or not to enable the panel switches  
Date display on/off selection  
PlayLock OFF  
EjectLockOFF  
Switch ENA  
DateDisp OFF  
FR Disp ON  
St.Tally ON  
PANEL KEY  
DISPLAY  
Eject lock  
Switch protect  
Date display  
Frame display  
Standby tally  
End cue  
Selection of whether or not to display frame  
Selection of whether to enable or inhibit the STDBY/CUE tally  
End cue time setting  
EndCue –2s  
DryCnt E.CUE  
T.Flash OFF  
Fader Pause  
9600bps  
PARALLEL  
REMOTE  
Tally selection  
Tally flash  
Setting of tally output signal with dry contact  
Setting of tally output lit or flashing  
Fader start  
Serial BPS  
Player ID  
Fader start mode selection  
Baud rate setting  
SERIAL  
REMOTE  
Player ID on/off selection and ID setting  
PlayerID OFF  
Program1 OFF  
Program2 OFF  
Program3 OFF  
HotStart OFF  
Ini. Preset  
Program 1  
Program 2  
Program 3  
Hot start  
Setting of whether or not to play program 1  
Setting of whether or not to play program 2  
Setting of whether or not to play program 3  
Hot start mode on/off selection for parallel remote  
Setting for clearing presets and setting them to the initial values  
PROGRAM  
HOT START  
CLEAR  
Preset clear  
S.xxxxD.yyyy  
(xxxx yyyy is a number.)  
VERSION  
38  
Set information  
Microprocessor version display  
13  
ENGLISH  
(2) Presetting Procedure  
• Functions can be preset using the buttons on the front panel.  
• The presettings can also be set using serial remote signals  
(RS232C/RS422A).  
• Presettings can be made when no cartridge is loaded or when  
in the stop, standby, pause, recording pause or recording  
monitor mode.  
Enter the preset mode.  
Playback speed select.  
Press the STANDBY/CUE button while pressing the  
MODE button.  
Turn the select knob to select the pitch.  
Flashing  
Character display  
1
2
3-  
Press the select knob to set the pitch.  
Lit  
Select the preset item.  
Turn the select knob.  
Character display  
Exit the preset mode.  
Press the MODE button.  
MODE  
Turn the knob  
4
5
clockwise to move in  
the direction of the  
arrows,  
counterclockwise to  
move in the opposite  
direction.  
The preset mode is canceled and the set returns  
to the previous mode.  
2
To set the presettings back to the initial settings (the  
settings set upon shipment from the factory).  
Turn the power on while holding in both the SEARCH 7  
and the SEARCH 6 buttons. For the initial settings,  
refer to “(1) List of preset functions”.  
NOTE: The first preset item displayed is the last preset  
item displayed the last time the presettings were  
made.  
The character display changes as  
shown below.  
Change the preset values.  
Press the select knob.  
NOTE:  
The character display changes as  
shown below.  
If the message shown below appears, there is a problem with  
the preset memory. Contact a serviceperson.  
InitialError  
1
3-  
Before change  
After change  
NOTE:  
The playback speed is the most recently set playback speed.  
For example, if the pitch is set with the presettings then set  
from the keyboard, the pitch set from the keyboard is used.  
Flashing  
14  
ENGLISH  
(3) Detailed Description of Preset Functions  
(* = initial setting)  
1) “Preset Area (*)” (Three different sets (areas) of presettings can be made and used for different purposes.)  
* Preset Area1  
Preset Area2  
Preset Area3  
:
:
:
Set to preset Area 1.  
Set to preset Area 2.  
Set to preset Area 3.  
2) “Finish (*)”  
Finish Stop  
* Finish Next  
Finish Recue  
Finish Repeat  
:
:
:
:
Stop mode is set after track playing is finished.  
Standby mode is set at next track after track playing is finished.  
Standby mode is set at playback start position after track playing is finished.  
The tracks are repeated according to the play mode.  
* When “Finish Repeat” is selected, the repeat mode cannot be turned on and off from the parallel or serial ports or  
from the keyboard.  
3) “Stereo (Mono)”  
* Stereo  
:
:
Output L and R stereo signals from the output connector.  
Output mixed L and R signals from the output connector.  
Mono  
4) “CueDet. OFF (–**) dB”  
* CueDet. OFF  
CueDet. (–**) dB  
:
:
Sound is not detected when cueing.  
Sound detection level setting for cueing. (–72/–66/–60/–54/–48/–42/–36)  
5) “D.Out Pro (Cons)”  
* D.Out Pro  
:
:
Output digital signals in AES/EBU format.  
Output digital signals in SPDIF format.  
D.Out Cons  
NOTE: Auto Cue is not possible when the above is set to “D.Out Cons”.  
6) “End Mon. (**) sec”  
End Mon. (**) sec  
End Mon. OFF  
:
:
Set the end monitor time. (5/*10/15/20/25/30/35)  
Do not use the end monitor function.  
7) “E.O.M. (**) sec” (Output EOM tally signal to remote pint (24))  
E.O.M. (**) sec  
E.O.M. OFF  
:
:
Set the EOM time. (5/*10/15/20/25/30)  
Do not use the EOM function.  
8) “Delay (***) ms”  
* Delay OFF  
:
:
Do not use the delay start function.  
This sets the delay time from which the playback operation is started until playback starts. (100/200/300)  
Delay (***) ms  
9) “Pitch (**.*) %”  
* Pitch OFF  
:
:
Playback at normal speed. (0.0 %)  
Playback at variable speed. (–8.0 ~ +8.0 %, 0.1 % step)  
Pitch (**.*) %  
10) PitchAuto OFF (ON)”  
* PitchAuto OFF  
:
:
Play pitch data stored on disc not used.  
Play disc at play pitch stored on disc.  
PitchAuto ON  
11) “Analog (Digital) IN”  
* Analog IN  
:
:
Select the Analog input signal for recording.  
Select the Digital input signal for recording.  
Digital IN  
12) “Rec Stereo (Mono)”  
* Rec Stereo  
:
:
Record in stereo.  
Record left channel signal in mono.  
Rec Mono  
13) “IncDet. (–**) dB”  
IncDet. (–**) dB  
:
Sound detection level for auto increment function. (–66/*–60/–54/–48/–42/–36)  
14) “AutoInc OFF (*)”  
* AutoInc OFF  
:
:
No auto increment of track number.  
Track number is automatically incremented during digital recording using subcodes on CDs or MDs (Q codes) or start  
AutoInc Dig.  
IDs on DATs.  
AutoInc Det.  
:
Track number is automatically incremented during recording when level set in “13) “IncDet. (–**) dB” setting is  
detected.  
15) “Pre UTOC OFF (ON)” (Playback is possible up to that point even if power supply is cut off during recording or if recording stops due to some  
problem.)  
* Pre UTOC OFF  
Pre UTOC ON  
:
:
Pre-UTOC function off.  
Pre-UTOC function on.  
15  
ENGLISH  
16) “ RecLv (–**) dB”  
RecLv (–**) dB  
:
Sound detection level for auto record start function. (–66/*–60/–54/–48/–42/–36)  
17) “RecOffset (*)” (Recording can be started before sound detection during auto record start operation.)  
RecOffset (*)  
:
Recording starts the set number of seconds before level detection. (*OFF/1s/2s/3s/4s/5s)  
18) “SCMS INH (ENA)”  
* SCMS INH  
:
:
Record onto disc same code as copy prohibit code in recording source.  
Record copy prohibit code on disc according to SCMS.  
SCMS ENA  
19) “Rec EOM (***) s”  
* RelayRec OFF  
:
Relay recording mode off.  
Rec EOM (***) s  
:
Set the Relay recording mode to on and set time at which the REC E.O.M. tally is to be output (the number of  
seconds before the end of the recordable time). (30/60/90/120)  
20) “Next Stb.OFF (ON)”  
* Next Stb.OFF  
:
:
Return to the play start position and standby when the STANDBY/CUE button is pressed during playback.  
Standby at the beginning of the next track when the STANDBY/CUE button is pressed during playback.  
Next Stb.ON  
21) “PlayLock ON (OFF)”  
PlayLock ON  
:
:
Inhibit all operations other than the PLAY/PAUSE, DISP buttons and PLAY MODE switch during playback.  
Enable all functions during playback.  
* PlayLock OFF  
22) “EjectLock ON (OFF)”  
EjectLock ON  
:
:
The EJECT button is locked during playback.  
The EJECT button is not locked during playback.  
* EjectLock OFF  
23) “Switch ENA (INH)”  
* Switch ENA  
:
:
Enable operation of all the switches on the front panel.  
Inhibit operation of all panel switches other than those used for presetting operations.  
Switch INH  
24) “DateDisp OFF (ON)”  
* DateDisp OFF  
:
:
Date not displayed even when DISP button pressed.  
Date displayed when DISP button pressed.  
DateDisp ON  
25) “FR Disp ON (OFF)”  
* FR Disp ON  
:
:
The frames are displayed on the time display during playback.  
The frames are not displayed on the time display during playback. (They are displayed in the manual search, standby,  
pause and end monitor modes.)  
FR Disp OFF  
26) “St.Tally ON (OFF)”  
* St.Tally ON  
:
:
The stdby/cue tally signal is output from the REMOTE connector (pins 16).  
The stdby/cue tally signal is not output from the REMOTE connector (pins 16).  
St.Tally OFF  
27) “EndCue (–*) sec” (Cue signal can be emitted before playback is completed.)  
EndCue (–*) sec End cue time setting. (0/–1/*–2/–3)  
:
28) “DryCnt (EOM/E.CUE/CUE)”  
DryCnt EOM  
* DryCnt E.CUE  
DryCnt CUE  
:
:
:
The end of massage tally signal is output from the REMOTE connector (pins 24).  
The end cue tally signal is output from the REMOTE connector (pins 24).  
The cue tally signal is output from the REMOTE connector (pins 24).  
29) “T.Flash ON (OFF)”  
* T.Flash ON  
:
:
PLAY TALLY blinks during the EOM for parallel remote tally output, PAUSE TALLY blinks when pause, and  
STDBY TALLY blinks during the search operation. (The same display as on the front panel is output.)  
The parallel remote tally output does not blink.  
T.Flash OFF  
The tally signal is output only when the PLAY/PAUSE and STDBY/CUE buttons’ displays are lit.  
30) “Fader Pause (Play)”  
* Fader Pause  
:
:
Start playback when remote fader pins (9–10) are short-circuited and pause when pins are open.  
Start playback when remote fader pins (9–10) are short-circuited and continue playback when pins are open.  
Fader Play  
31) “9600 (19200) bps”  
* 09600 bps  
:
:
Set the baud rate to 9600 bps.  
Set the baud rate to 19200 bps.  
19200 bps  
32) “PlayerID (**)”  
PlayerID (**)  
:
Player ID setting.  
(Set ID to OFF or 0 to 15. Default setting – “OFF”)  
16  
ENGLISH  
33) “Program1 OFF (ON)”  
Program1 OFF (ON) : Store the contents of program 1 when on. (Initial setting – “OFF”)  
34) “Program2 OFF (ON)”  
Program2 OFF (ON) : Store the contents of program 2 when on. (Initial setting – “OFF”)  
35) “Program3 OFF (ON)”  
Program3 OFF (ON) : Store the contents of program 3 when on. (Initial setting – “OFF”)  
36) “HotStart OFF (ON)”  
* HotStart OFF  
:
:
The parallel remote is set up the Hot start off mode.  
The parallel remote is set up the Hot start on mode.  
HotStart ON  
37) “Preset Clr? (Ini. Preset)”  
Preset Clr?  
* Ini. Preset  
:
:
Clear the presettings (set to the initial factory values).  
Presettings set to initial factory defaults.  
38) “S.xxxxD.yyyy”  
:
Display the microprocessor version. (“xxxx yyyy” is a number.)  
17  
ENGLISH  
5
BASIC OPERATION  
Presetting the next track to be played during playback.  
• The track at which the standby mode is to be set or the  
track to be played next after the current track is played  
can be preset by turning the SELECT knob during  
playback.  
(1) Starting Playback  
Load the cartridge.  
1
In the single mode, the standby mode is set at the  
beginning of the next track.  
In the continuous mode, the next track is played  
when playback of the current track finishes.  
• The Next Track display of the set track number flashes.  
Make the presettings according to the usage purpose.  
(See Page 13.)  
NOTE: Steps 1, 2 and 3 can be performed in the opposite  
2
3
1
6-  
order.  
Example: When track 7 is selected while playing track 1  
Select the play mode.  
Turn the PLAY MODE switch.  
Flashing  
Single track play mode  
Lit  
Playback can be stopped in the following ways:  
Continuous play mode  
Select the track to be played.  
Turn the select knob.  
Flashing  
Lit  
Playback is interrupted, the pickup returns  
to the play start position and the standby  
mode is set. (BACK CUE)  
2
6-  
1
4-  
Playback is interrupted and the  
pause mode is set at that point.  
Flashing during search  
Lit when in standby  
The selected track is cued and the standby mode is set.  
Flashing (orange)  
Starting playback from the middle of track.  
• To start from the middle of a track, use the SEARCH  
buttons to move to the desired position.  
• Press one of the SEARCH buttons (6 or 7) in the  
play, pause or standby mode to set the search mode.  
• Press the 7 SEARCH button to move forward, the  
6 SEARCH button to move backward.  
2
4-  
To move forward  
To move backward  
(2) End Monitor  
Start playback.  
Press the PLAY/PAUSE button.  
To check the play end position.  
Press the END MON button when in the standby mode.  
Lit  
Lit (green)  
Off  
5
Playback begins and the playback signals are output.  
The track’s end is monitored, then the pickup returns to  
the play start position and the standby mode is set. (End  
Monitor)  
1
NOTE: If the STANDBY/CUE button is pressed during the  
end monitor operation, the end monitor operation  
is canceled, the pickup returns to the play start  
position and the standby mode is set.  
18  
ENGLISH  
(3) PLAY/PAUSE and STANDBY/CUE Operations  
(4) Before Starting to Record  
• The operation switches between playback and pause each time  
the PLAY/PAUSE button is pressed.  
• When the STANDBY/CUE button is pressed during playback,  
the pickup returns to the position at which playback was  
started.  
• Turn on the power. To record from the analog input, it is  
recommended to turn on the power at least 5 minutes before  
starting to record. This eliminates fluctuations of the A/D  
converter DC offset, reduces the amount of DC offset at the  
recording start position, in the middle of the recording and at  
the recording end position, and keeps the DC offset constant.  
DC offset hinders the auto cue function for detecting the point  
where the sound starts at low levels and the auto track  
increment function which detects soundless sections.  
The diagrams below show playback patterns when the  
PLAY/PAUSE and STANDBY/CUE buttons are pressed.  
• Load a recordable disc. There are 60-minute and 74-minute  
recordable discs. For a description of recordable discs, see the  
section “Method of Recording on Discs” below. It is not  
possible to record on discs which are already recorded and  
have little free space left or on playback only discs.  
PLAY and PAUSE  
PLAY/PAUSE PLAY/PAUSE  
button  
pressed  
button  
pressed  
PLAY/PAUSE button pressed  
Position on disc  
Section  
played  
(5) Method of Recording on Discs  
Section  
played  
Disc for recording  
Method of recording on disc  
Pause mode set at this point  
Recording starts from the beginning  
of the disc.  
The beginning of the disc is found  
automatically, so there is no need to  
do this manually.  
Discs  
nothing is recorded  
on  
which  
1
2
PLAY and CUE  
PLAY/PAUSE  
button  
STANDBY/CUE button pressed  
Recording on discs  
after erasing all their  
tracks  
pressed  
Same as above.  
Position on disc  
Section  
played  
Recording starts from the end of the  
last recorded section.  
Back Cue  
The end of the last recorded section  
is found automatically, so there is no  
need to do this manually.  
The set is designed so that it is not  
possible to record over a recorded  
section, so you cannot accidentally  
erase a previous recording.  
Recording on an  
already recorded disc  
3
PLAY, PAUSE and CUE  
PLAY/PAUSE PLAY/PAUSE PLAY/PAUSE  
button  
pressed  
button  
pressed  
button  
pressed  
STANDBY/CUE  
button pressed  
If there is not enough remaining  
space or if you want to do the  
recording over, erase before  
recording.  
Position on disc  
Section  
played  
Section  
played  
Recording on discs  
after erasing part or all  
of the disc  
4
To erase one track at a time:  
Use the track erase function.  
To erase all the tracks at once:  
Use the all erase function.  
Disc types  
Blank discs:  
Discs on which nothing is recorded  
Discs you have just bought  
Discs that have been erased (using the all erase  
function)  
No-track discs:  
Discs on which nothing is recorded but which  
contain a disc name  
Blank discs which have been given a disc name  
Discs with disc names on which all the tracks have  
been erased individually  
19  
ENGLISH  
(6) Starting to Record  
Load the cartridge.  
To pause recording:  
Press the PLAY/PAUSE button.  
1
Set the presettings according to the purpose.  
(Refer to Page 13.)  
NOTE: Steps 1 and 2 can also be performed in the reverse  
order.  
2
Flashing (orange)  
Lit  
6
Set the recording pause mode.  
Press the REC button.  
Recording stops and the recording pause mode is set.  
To resume recording, press the PLAY/PAUSE button  
again. The track number is incremented and recording  
resumes.  
Flashing (orange)  
Lit  
3
For a disc on which 3 tracks  
are already recorded.  
The disc’s total number of tracks and playing time are  
displayed.  
NOTE: If the REC button is pressed in the stop mode, the  
recording monitor mode is set. (Only the REC  
button lights.)  
(7) Stopping Recording  
Start recording.  
Press the PLAY/PAUSE button.  
Use one of the following methods to stop recording.  
Lit once in standby  
Lit (green)  
Lit  
4
5
1
Recording stops, the UTOC is written  
and the standby mode is set.  
TOC  
Recording starts and the  
indicator lights.  
NOTE: If the DIGITAL IN indicator is flashing, the digital  
signal is unlocked. If this is the case, recording is  
not possible.  
TOC  
The  
written.  
indicator flashes while the UTOC is being  
To change the track number during recording:  
Press the REC button.  
The track number is incremented and  
recording continues.  
20  
ENGLISH  
(8) Starting Recording Automatically by Detecting the  
Input Level  
This function makes it possible to start recording by detecting the  
input signal level.  
When the LEVEL START button is pressed in the input  
Set the presettings.  
signal detection mode, recording starts immediately.  
Make the following settings, referring to “Preset  
Functions and Operations” on Page 13.  
16) RecLv (–**) dB  
Recording starts when a signal with a level at or  
above the set level is input.  
17) RecOffset (*)  
During recording  
4
5
1
REC  
ON/OFF  
PLAY/PAUSE  
Recording begins this number of seconds before  
the point where the set level is detected.  
LEVEL  
START  
Lit  
Lit  
Lit  
Set the recording pause mode.  
Press the REC button.  
To stop recording:  
Press the PLAY/PAUSE, STANDBY/CUE or STOP  
(Keyboard) button.  
2
Lit  
Flashing  
(orange)  
NOTE:  
The auto track increment function and Auto Level Rec start  
function may not work when recording analog signals containing  
much noise. In this case lower the detection level to for  
example –54 dB.  
Set the recording level start mode.  
Press the LEVEL START button.  
Flashing  
3
4
NOTE: If the LEVEL START button is pressed while the  
button is flashing, the recording level start mode is  
canceled.  
Start recording.  
Press the PLAY/PAUSE button.  
PLAY/PAUSE  
PLAY/PAUSE  
REC  
ON/OFF  
LEVEL  
START  
Lit  
Lit  
Flashing  
(orange)  
Recording starts when an input signal with a level at or  
above the set level is detected.  
21  
ENGLISH  
Start of recording  
(9) Incrementing Track Numbers  
During recording, track numbers can be incremented either  
manually or automatically.  
• Track numbers can be incremented manually in the following  
three ways:  
Track  
number  
Track X Track Y  
Track Z  
Copy  
Start of recording  
End of recording  
1) Press the REC button (4) during recording. This increments  
the track number.  
2) Press the PLAY/PAUSE button (13) during recording to  
stop recording for that track number and set the recording  
pause mode.  
Track  
number  
Track A Track B Track X Track Y  
Track Z  
Previously recorded  
tracks  
Tracks recorded  
from the CD (MD)  
3) After recording, use the divide function.  
3) Using the DAT’s start IDs (digital input)  
• Track numbers can be incremented automatically in the  
following three ways, according to the type of input signal:  
q Record the start ID on the recorded DAT.  
w Make the following presetting:  
• Set “AutoInc OFF” 14) to “AutoInc Dig.”  
Input type  
Method  
e Start playback on the DAT player and recording on the  
recorder in such a way that the beginning of the sound is not  
missed. The disc’s track number is automatically  
incremented when the DAT’s start ID is detected. The start  
ID will not be detected for 15 seconds after the track number  
is incremented.  
Analog/digital input  
Detection of soundless section 1)  
Detection of soundless section 1)  
Using the CD’s or MD’s subcodes 2)  
Detection of soundless section 1)  
Using the DAT’s start IDs 3)  
CDs  
and  
MDs  
Digital input  
DATs  
Start of recording  
1) Detection of soundless section  
Track  
DAT  
Copy  
1
3
2
q Make the following two presettings:  
number  
Track X Track Y Track Z  
• Set “AutoInc OFF” 14) to “AutoInc Det.”  
• Set the soundless detection level setting to “IncDet. (–60)  
dB” 13).  
Start of recording  
End of recording  
w Start playback and recording in such a way that the beginning  
of the sound is not missed. When a soundless section (or a  
section with level lower than the preset soundless detection  
level setting) of at least 2 continuous seconds is detected,  
the disc’s track number is automatically incremented.  
Track  
number  
MD  
1
2
3
4
5
Track A Track B Track X Track Y Track Z  
Previously recorded  
tracks  
Tracks recorded  
from the DAT  
2 seconds or more  
(10) Pre-UTOC Function  
• Presettings must be set. (Refer to Page 15.)  
Input signal  
This function protects the recording should the power supply be  
cut off. The UTOC is written directly after recording starts.  
(The pre-UTOC is written.)  
Soundless section  
Track number is incremented  
Normally the UTOC is written after recording is completed, so if  
the power supply should be cut off during the recording or directly  
after the recording is finished, the recording will not be registered  
on the disc. To prevent this, the pre-UTOC (*1) is registered on  
the disc directly after recording starts. Once recording is  
completed normally, the actual UTOC (*2) is written. If the power  
should be cut before the actual UTOC is written, the disc can be  
played according to the pre-UTOC. This way you never  
accidentally lose recordings that cannot be made over again.  
NOTE: The auto track increment function may not work when  
recording analog signals containing much noise. In this case  
lower the detection level to for example –54 dB.  
2) Using the CD’s or MD’s subcodes (digital input)  
q Make the following presetting:  
• Set “AutoInc OFF” 14) to “AutoInc Dig.”  
w Start playback on the CD (MD) player and recording on the  
recorder in such a way that the beginning of the sound is not  
missed. The disc’s track number is automatically  
incremented when the CD’s (MD’s) track number changes.  
Changes in the CD’s (MD’s) track number will not be  
detected for approximately 4 seconds after the track number  
is incremented.  
Entire disc  
Pre-UTOC (*1)  
Start of recording  
UTOC (*2)  
End of recording  
If some problem occurs and recording is interrupted, the same  
recording and UTOC can be written using the following editing  
operation:  
Use the divide function at the point where recording was  
interrupted in track 03 on the above diagram to divide the track,  
then use the erase function to erase track 04.  
NOTE:  
The auto track increment function using the DAT’s start ID or the CD’s sub codes will not work if the digital input is in professional format  
(AES/EBU). Input digital signals of the consumer format (SPDIF).  
22  
ENGLISH  
6 HANDY OPERATIONS  
(1) Setting Cue Points  
With this function, cue points can be set at any positions in tracks  
then searched for during playback. Up to five cue points can be  
set per track.  
In the standby, pause, manual search or play mode:  
Press the REC button while UTOC Write? is displayed.  
Set the EDIT mode.  
Press the MODE button.  
1
2
5-  
MODE  
MODE  
Flashing  
EDIT  
Lit  
Off  
Off  
Find the position at which you want to set the cue  
point.  
Use the SEARCH 7/6 buttons to find the position at  
which you want to set the cue point.  
To set cue points during recording:  
2
Press the CUE WRITE button.  
1
6-  
Set the cue point.  
Press the CUE WRITE button.  
Lit  
1
3-  
3-  
Press the CUE WRITE button again while Cue Write OK?  
is displayed.  
Lit  
Press the CUE WRITE button again while Cue Write OK?  
Flashing  
2
6-  
is displayed.  
Off  
2
Flashing  
NOTE: The UTOC is written once recording is completed.  
Off  
Lit  
Flashing  
To continue setting other cue points:  
Repeat steps 2, 3-1 and 3-2.  
4
Write the UTOC. (Cancel the edit mode.)  
Press the MODE button.  
1
5-  
Lit  
23  
ENGLISH  
(2) Direct Search for Cue Points  
When cue points are stored on a track, they can be used for direct  
search.  
Load the cartridge.  
1
2
Set the cue direct search mode.  
Press the CUE SEARCH button.  
Lit  
NOTE: The cue direct search mode cannot be set if no cue  
points are stored on the disc.  
Search for the cue point.  
Press the STANDBY/CUE button.  
Flashing  
Lit  
Lit  
1
3-  
Flashing  
The Cue1 point is searched for and the standby mode is  
set at that position.  
Press the STANDBY/CUE button again to search as  
follows:  
Cue points can also be searched for by turning the select  
knob.  
When turned clockwise:  
2
3-  
When turned counterclockwise:  
Cancel the cue direct search mode.  
CUE  
SEARCH  
CUE  
SEARCH  
4
Off  
The set returns to the normal operating mode.  
24  
ENGLISH  
(3) Instantaneous play (Hot Start)  
NOTES:  
Preset up to 10 tracks using the parallel remote, the serial  
remote or a key board (PS/2 connector, US keyboard with  
101 or 104 keys recomended) to enable instantaneous play of  
the desired tracks. This function is called instantaneous play  
(Hot Start).  
• The instantaneous play (Hot Start) mode will end with one  
track.  
• A press of a number button during the instantaneous play  
(Hot Start) mode will cause the unit to switch to the track of  
the pressed number and start playing.  
When parallel remote is to be used, a control circuit for  
instantaneous play (Hot Start) is required. For information about  
the control circuit, contact your store of purchase.  
When serial remote is to be used, contact your store of  
purchase.  
• Cue detection is also performed at the time of instantaneous  
play (Hot Start) loading.  
Tracks with a setting level less than 10 seconds from the  
beginning of the track are loaded from the beginning of the  
track.  
Even when the level of cue detection is changed after  
loading, the pause position will not change until the initial  
data is cleared.  
NOTE:  
The hot start data is cleared if the editing or recording operations  
are performed during the hot start mode.  
Hot Start Load  
Data loading.  
Hot Start  
Starting the play operation.  
During instantaneous play (Hot Start) standby, press the  
number button (from 1 to 10) that is to be played to start  
the instantaneous play (Hot Start) operation.  
Set the cartridge and cue or pause at the track for hot  
1
start playback.  
10 TRACK LOAD.  
Press the the LOAD button.  
• The data for ten tracks starting from the track at which  
the cue or pause mode is set is loaded into the hot start  
RAM.  
1
The number of the button for the track at which  
playback started is shown on the display.  
• The PLAY/PAUSE button flashes when an EOM is  
detected during playback (when the EOM is turned on  
with the presetting).  
• When play finishes, the unit returns to instantaneous  
play (Hot Start) standby.  
(Example: Track 4 is set to pause)  
1
Stopping the play operation.  
2-  
Disc  
A press the STOP button during the play  
operation causes the play to stop and  
returns the unit to instantaneous play (Hot  
Start) standby.  
2
3
Instantaneous  
play  
(Hot Start)  
• When the data loading is completed, the  
STANDBY/CUE button will light and the unit will be set  
to instantaneous play (Hot Start) standby.  
Repeat play.  
When the REPEAT button is pressed, the repeat mode is  
set.  
Press the number button of the track to be played (from 1  
to 10) to repeatedly play that track.  
• Press the REPEAT button while a track  
is being played to repeatedly play that  
NOTE: When the stop operation is set during data loading  
and the data loading number (from 1 to 10) is  
completed, data loading of subsequent tracks is  
stopped.  
REPEAT  
track.  
1 TRACK LOAD.  
• Press the REPEAT another time to  
cancel the repeat play mode.  
While depressing the LOAD button, press the number  
button (from 1 to 10) for which data is to be entered.  
Set the standby mode and press the MODE button on  
the main unit twice to cancel the hot start mode.  
2
3
2-  
2-  
MODE  
• The hot start mode is canceled and the  
4
edit mode is set.  
• When data loading is completed, the CUE LED lights  
steadily.  
PROGRAM TRACK LOAD.  
• Hot start data can also be loaded in the programmed  
play mode. The data is loaded in the programmed order.  
The programmed play mode is canceled after the data is  
loaded.  
25  
ENGLISH  
7
PROGRAMMED PLAYBACK  
• The tracks can be programmed to play in a certain order.  
• Up to 25 tracks can be programmed.  
• Programmed playback is performed according to the play mode  
(single or continuous) and preset finish mode (stop, next, recue or  
repeat) settings.  
(2) Changing Programs  
Set the program edit mode.  
Press the PROGRAM IN button.  
(1) Inputting Programs  
1
Flashing  
Set the program input mode.  
Press the PROGRAM IN button.  
The step  
number  
lights  
1
Flashing  
Select the step number to be edited.  
Turn the select knob.  
The step  
number  
flashes  
To edit the third step in the program:  
2
3
Select the track to be programmed.  
Turn the select knob.  
Lit  
When track 3 is selected:  
2
Set the program change mode.  
Press the select knob.  
Selected track number  
Flashing  
Enter the selected track in the program.  
Press the select knob.  
The step number to be edited flashes  
To change the track:  
Select the track to be changed.  
Turn the select knob.  
3
4
5
Lit  
The number of the next step in  
the program is displayed.  
When track 7 is selected:  
1
4-  
Enter the next track in the program.  
Press the select knob.  
Selected track  
number  
Flashing  
Enter the selected track.  
Press the select knob.  
Flashing  
The time display shows the total  
playing time for the program.  
Repeat steps 2, 3 and 4 to program the tracks in the  
desired order.  
2
4-  
Exit the program input mode.  
Press the PROGRAM IN button.  
The number of the next step  
in the program lights  
To continue editing the program, repeat steps 2, 3, 4-1 and  
4-2.  
Lit  
To exit the program editing mode, press the PROGRAM IN  
The set returns to the normal mode.  
button. The set returns to the normal mode.  
26  
ENGLISH  
(3) Playing Programs  
Inserting a track in the program.  
Set the program play mode.  
Press PROGRAM ON/OFF button.  
Select the position at which to insert a track.  
Turn the select knob.  
To insert a track at the third step  
in the program:  
1
5-  
Lit  
1
Lit  
Flashing  
Lit  
Set the program insert mode.  
Press the SEARCH 7 button.  
Number of  
next step  
Lit  
2
3
5-  
5-  
The first track in the program is cued and the standby  
mode is set.  
The step number flashes  
Start programmed playback.  
Press the PLAY/PAUSE button.  
Perform the same operations as in steps 4-1 and 4-2 to  
select the track to be inserted.  
STANDBY/CUE  
PLAY/PAUSE  
PLAY/PAUSE  
2
To insert more tracks in the program, repeat steps 5-1,  
5-2, and 5-3.  
Lit  
Programmed playback starts.  
Off  
(To exit the program insert mode, press the PROGRAM IN  
button.)  
Deleting tracks from the program  
• When the cartridge is ejected, the set program is cleared.  
• If a track that is not in the program is selected with a serial  
command during programmed playback, that command is  
ignored.  
Select the step to be deleted.  
Turn the select knob.  
To delete the track at the third step:  
1
6-  
NOTE:  
Programs cannot be input when no disc is loaded.  
Lit  
Delete that track from the program.  
Press the SEARCH 6 button.  
Number of track at the next step in the program:  
2
6-  
The next step number lights  
To continue deleting tracks from the program, repeat  
steps 6-1 and 6-2.  
Exit the program editing mode.  
Press the PROGRAM IN button.  
7
Lit  
27  
ENGLISH  
(4) Presetting Programs  
• Programs can be stored in the preset memory. When a  
cartridge for which a program is preset is loaded, the  
programmed playback mode is set automatically.  
• Programs can be stored for up to three cartridges.  
Input the program.  
Following the instructions under “(1) Inputting Programs”  
to input the program. (See Page 26.)  
1
Set the preset mode.  
Follow the instructions under “(2) Presetting Procedure”  
to set the preset mode. (See Page 14.)  
1
2-  
Select the preset item.  
Turn the select knob to select “Program 1” (or “Program  
2” or “Program 3”).  
Character display  
2
2-  
Select one of  
these.  
Change the preset setting.  
Press the select knob.  
The character display changes as follows:  
3
2-  
2-  
Before change  
After change  
Cancel the preset mode.  
Press the MODE button.  
MODE  
4
The preset setting mode is canceled and the  
set returns to the normal mode.  
28  
ENGLISH  
8
EDITING FUNCTIONS  
(1) Editing Functions  
There are nine editing functions possible on MDs, as described  
below. Here we describe these functions briefly.  
i Disc name/Track name function  
Disc names or track names can be stored on recorded discs.  
The disc names and track names can be called out on the  
display using the display function.  
q Cue erase function (erasing cue signals)  
Cue signals (external control signals) recorded on the disc can  
be erased without affecting the tracks.  
o Undo functions (for undoing the editing)  
Even after editing is completed, the editing can be undone as  
long as the UTOC has not yet been written.  
There are three types of undo functions:  
w Track erase function (for erasing specific tracks)  
An entire track, from beginning to end, can be erased  
instantaneously simply by operating buttons. Unlike tapes,  
there is no need to record over, erase, or cut the tape.  
1) UNDO: For undoing the last editing operation.  
2) REDO: For resetting the editing undone with the undo  
function.  
Track number  
1
2
3
3) FIRST: For undoing all the editing operations.  
Track A  
Track A  
Track B  
Track C  
When three editing operations have been performed:  
Track B erased  
1
2
Original  
Editing 1  
Editing 2  
Editing 3  
Track C  
When the undo function is used: Only the first two editing operations remain.  
Original Editing 1 Editing 2 Editing 3  
e All erase function (for erasing all the tracks on the disc)  
All the tracks on the disc can be erased instantaneously simply  
by operating buttons. Unlike tapes, there is no need to use an  
eraser or record over.  
When the undo function is used again: Only the first editing operation remains.  
Original Editing 1 Editing 2 Editing 3  
r Divide function (for dividing a track in two)  
One track can be divided into two tracks. This makes it  
possible to easily set search points simply by operating  
buttons after recording.  
When the redo function is used: The first two editing operations remain.  
Original Editing 1 Editing 2 Editing 3  
When the first function is used: None of the editing operations remain.  
Original Editing 1 Editing 2 Editing 3  
Track number  
Track A  
Track A  
Track B Track C  
Track D  
(Editing operations 1, 2 and 3 cannot be retrieved.)  
Divide function used  
Track B Track C  
Track D  
Point where track  
was divided  
NOTE:  
During the edit mode, the eject lock function is set and the  
cartridge can not be ejected.  
t Combine function (for combining two tracks)  
Short recordings or cuts created by dividing tracks can be  
combined into a single track. Unlike tapes, there is no need to  
copy over or cut the tape.  
Track number  
Track A  
Track A  
Track B Track C  
Track D  
Combine function used  
Track B Track C  
Track D  
Point where tracks  
were combined  
y Move function (for moving tracks)  
The order of the tracks can be changed. Unlike tapes, there is  
no need to copy over or cut the tape.  
Track number  
Track A  
Moved  
Track B Track D  
Track C  
Track C  
Move function used  
Track D  
Track A  
Track B  
u Pitch on the disc function (Disc’s Pitch)  
This function make it possible to set and store a certain play  
speed on the disc, then play the disc at that speed.  
When the presetting is set to “PitchAuto ON” and this disc is  
loaded, the disc is played at the written pitch.  
29  
ENGLISH  
(2) Editing Function Select  
(3) Erasing Cue Signals ‹Cue erase function›  
Load the cartridge.  
1
Set the cue mode at the position of the cue signal you  
want to erase.  
Press the CUE SERCH button.  
Set the edit mode.  
Press the MODE button.  
1
1-  
Lit  
Lit  
2
The cue direct search mode is set.  
Press the STANDBY/CUE button.  
Lit  
Lit  
Select the edit track.  
The track to be edited can be selected  
(or changed) by turning the SELECT  
knob.  
1
3-  
3-  
Flashing  
Lit  
2
1-  
Set the edit function select mode.  
Select the edit track and press the SELECT knob.  
Flashing  
NOTE:  
2
Press the CUE button again to search for “Cue2”, “Cue3”,  
etc., and set the cue.  
NOTE:  
“Cue Erase?” is not displayed if no cue signal  
is set.  
Select the cue erase edit function. (see page 30.)  
Select “Cue Erase?” and Press the SELECT knob.  
Select the edit function.  
Turn the select knob.  
2
3
Erase the cue signal.  
Press the REC button.  
4
Lit  
Off  
The cue signal is erased and the mode returns to the edit  
mode.  
NOTES:  
• “Cue Erase?” is not displayed if no cue signals is set.  
• “Divide?”, “Combine?” and “Move?” are not displayed  
in the stop mode.  
After selecting the edit function in item 3, perform the  
operations for the various edit items.  
Cue Erase?  
Track Erase?  
All Erase?  
Divide?  
page 30  
page 31  
page 31  
page 32  
page 32  
Move?  
page 33  
page 33  
page 34  
page 34  
|
|
|
|
|
|
|
|
|
Pitch? **.*%  
Disc Name?  
Track Name?  
5
6
Combine?  
Cancel the edit mode.  
Press the MODE button before press the SELECT knob.  
Cancel the edit function. (after selected the edit item.)  
Press the MODE button before press the REC button.  
30  
ENGLISH  
(4) Erasing Tracks  
(5) Erasing All the Tracks on the Disc  
‹All erase function›  
‹Track erase function›  
Select the track erase function. (see page 30.)  
Select the all erase edit function. (see page 30.)  
Select “Track Erase?” and press the SELECT knob.  
Select “All Erase?” and press the SELECT knob.  
1
2
1
Select the erase track.  
Erase all the tracks on the disc.  
Press the REC button.  
The track to be erased can be selected  
(or changed) by turning the SELECT  
knob.  
2
Lit  
Erase the select track.  
Press the REC button.  
All the tracks are erased and the mode returns to the edit  
mode.  
3
Lit  
The track is erased and the mode returns to the edit  
mode.  
31  
ENGLISH  
(6) Dividing Tracks into Two Parts  
(7) Combining Two Tracks  
‹Combine function›  
‹Divide function›  
Select the combine edit mode function. (see page 30.)  
Select “Combine?” and press the SELECT knob.  
Use manual search, etc., to find the point at which you  
want to divide the track.  
1
Select the divide edit function. (see page 30.)  
Select “Divide?” and press the SELECT knob.  
1
2
2
Select the tracks to be combined.  
Use the select knob to set the cue mode at the second of  
the tracks to be combined.  
The section from three seconds before the divide point to  
the divide point is played repeatedly.  
NOTE:  
To combine tracks 02 and 03:  
To move the divide point, press the SEARCH button.  
Divide the track.  
Press the REC button.  
cue  
02Tr  
03Tr  
Combine the tracks.  
Press the REC button.  
3
Lit  
The track is divided and the mode returns to the edit  
mode.  
3
Lit  
The tracks are combined and the mode returns to the edit  
mode.  
NOTE:  
The divide operation cannot be performed if cue signals are set  
for that track.  
(Clear all the cue signals first.)  
NOTES:  
• If the tracks have track names, the name of the second track  
will be cleared.  
• The following tracks cannot be combined:  
1) When cued at the first track  
2) A stereo track with a monaural track  
3) Tracks containing cue signals  
32  
ENGLISH  
(8) Moving Tracks  
‹Move function›  
(9) Pitch on the disc  
‹Disc’s pitch function›  
Select the move edit function. (see page 30.)  
Select “Move?” and press the SELECT knob.  
Select the disc’s pitch function. (see page 30.)  
Select “Pitch? **.*%” and press the SELECT knob.  
1
1
2
Flashing  
Use the SELECT knob to choose where to move which  
track.  
Select the pitch.  
The pitch can be selected by turning the SELECT knob.  
To move track 5 to track 1:  
Flashing  
Flashing  
2
Write the pitch on the disc.  
Press the REC button.  
Flashing  
Press the SELECT knob.  
Flashing  
Flashing  
3
Lit  
The pitch is written and the mode returns to the edit  
mode.  
Move the track.  
Press the REC button.  
• Disc’s pitch  
When preset 10 is set to “PitchAuto ON” and a disc on which the  
pitch is recorded is loaded, the recorded pitch is set automatically  
after the UTOC is read.  
3
Lit  
The track is moved and the mode returns to the edit  
mode.  
33  
ENGLISH  
(10) Inputting (Changing) Names  
‹Title function›  
Select the name input edit item. (see page 30.)  
Select “Track Name?” or “Disc Name?” and press the  
SELECT knob.  
Set the name.  
Press the REC button.  
5
Lit  
1
Flashing  
Lit  
Lit  
The name is set and the mode returns to the edit mode.  
If a name is already set, the name is displayed and the first  
character flashes.  
Select the type of characters to be input.  
Press the CAPS/NUM button and select the type of  
characters.  
Input Characters  
The following letters, numbers and symbols (ASCII code) can be  
selected using the CAPS/NUM button and the select knob:  
DISP  
1
2-  
2-  
Capital  
letters  
Small  
letters  
Num-  
bers  
Symbols  
Turn the SELECT knob to select the character to be input.  
2
Enter the selected character.  
Press the SELECT knob.  
3
4
NOTE:  
Disc and track names can be up to 100 characters long, but the  
maximum number of characters that can be set for the disc  
name and all the track names is 1700.  
Flashing  
Continue inputting the name.  
Repeat steps 2-1, 2-2 and 3 to input the name.  
Press the SEARCH 6 or 7 button to move the cursor  
to change or correct a name.  
Flashing (cursor)  
When the SEARCH 6 or 7 button is pressed, the  
cursor moves one space.  
Backwards  
Forwards  
Press the SELECT knob to insert characters, the CLEAR  
button to delete characters.  
34  
ENGLISH  
(11) Exit the Edit Mode or Undoing Editing  
‹Undo functions›  
Press the MODE button.  
• When editing is executed, the message “UTOC Write?”  
asking you whether or not you want to write the UTOC  
is displayed.  
1
• The edit mode is canceled when editing is not being  
executed.  
ª
Exit the Edit Mode.  
Select the undo mode.  
Write the UTOC EDIT.  
Turn the select knob.  
Press the REC button while UTOC Write? is displayed.  
Off  
2
2
UNDO: For undoing the last editing operation.  
REDO: For resetting the editing undone with the undo  
function.  
Flashing  
Flashing  
The edit mode is canceled after the UTOC is written.  
FIRST: For undoing all the editing operations.  
Undo the editing.  
Press the REC button.  
NOTES:  
• The undo operation can be used to undo up to the two last  
editing operations. To undo previous editing operations, use  
the “First” operation to undo all the editing operations, then  
redo the editing.  
• Once the UTOC is written or after the Names are inputed, it is  
not possible to change previous editings.  
• If editing is performed when a program is set, the program is  
discarded.  
1
3-  
The editing is undone and the mode returns to the edit  
mode.  
Cancel the undo mode.  
Press the MODE button before press the REC button.  
(Return to step 1)  
2
3-  
35  
ENGLISH  
9
CONNECTING AND OPERATING A KEYBOARD  
An IBM PC compatible keyboard can be connected and used to control  
the DN-M991R.  
When the Shift key is held in while pressing keys F1 to F12  
,
Connectable keyboard: IBM US101 keyboard  
the keys function as follows:  
(connector: 6-pin mini DIN PS/2 type)  
Applicable cord:  
SCAN CODE SET 02  
F1  
F2  
Track search reverse (10 tracks)  
Track search forward (10 tracks)  
Manual search reverse  
Manual search forward  
CUE SEARCH button  
LEVEL START button  
CUE WRITE button  
Reserved  
(1) Connecting the Keyboard  
F3  
DN-M991R  
F4  
F5  
F6  
F7  
F8  
F9  
REPEAT button  
F10  
F11  
F12  
PROGRAM IN button  
Loads hot start data  
TITLE IN button  
Keyboard  
When the Ctrl key is held in while pressing keys F1 to F12  
,
the keys function as follows:  
F1  
F2  
PRESET button  
NOTE: Turn off the power of the DN-M991R before connecting  
Selects First in edit mode  
Selects Redo in edit mode  
Selects Undo in edit mode  
MODE button  
the keyboard.  
F3  
F4  
(2) Keyboard Operations  
F5  
The keyboard’s keys are allocated to specific DN-M991R panel  
operations. The functions of the keys differ according to the DN-  
M991R’s operating mode.  
F6  
Selects DIVIDE in edit mode  
Selects COMBINE in edit mode  
Selects MOVE in edit mode  
Selects Disc’s pitch in edit mode  
Selects Cue Erase in edit mode  
Selects Track Erase in edit mode  
Selects All Erase in edit mode  
F7  
• Functions of keys F1 to F12  
F8  
F9  
Esc  
_
F1  
F2  
F3  
F4  
F5  
F6  
F7  
F8  
F9  
_
F10  
F11  
F12  
Print  
Scrol  
Pause  
!
1
@
2
#
3
$
4
%
5
^
6
&
7
(
9
)
0
+
=
NumLk  
/
-
F10  
F11  
F12  
8
J
Backspace  
Ins  
Home  
End  
PgUp  
PgDn  
{
[
}
]
|
/
7
8
5
2
9
Tab  
Q
W
Z
E
X
R
C
T
V
Y
B
U
N
I
O
P
Del  
Home  
PgUp  
+
:
;
"
`
4
6
Capslock  
Shift  
A
S
D
F
G
H
K
L
Enter  
<
,
>
.
?
/
1
End  
3
M
Shift  
PgDn  
Enter  
0
Ctrl  
Alt  
Alt  
Ctrl  
Ins  
Del  
• Functions of other keys  
1) In normal operating mode  
F1  
F2  
Track search reverse (1 track)  
Track search forward (1 track)  
PLAY/PAUSE button  
STANDBY/CUE button  
STOP button  
Esc  
_
F1  
F2  
F3  
F4  
F5  
F6  
F7  
F8  
F9  
_
F10  
F11  
F12  
Print  
Scrol  
Pause  
!
1
@
2
#
3
$
4
%
5
^
6
&
7
(
9
)
0
+
=
NumLk  
/
-
8
J
Backspace  
Ins  
Home  
End  
PgUp  
PgDn  
{
[
}
]
|
/
7
8
5
2
9
F3  
Tab  
Q
W
Z
E
X
R
C
T
V
Y
B
U
N
I
O
P
Del  
Home  
PgUp  
+
:
;
"
`
4
6
Capslock  
Shift  
A
S
D
F
G
H
K
L
Enter  
F4  
<
,
>
.
?
/
1
End  
3
M
Shift  
PgDn  
Enter  
0
Ctrl  
Alt  
Alt  
Ctrl  
Ins  
Del  
F5  
F6  
REC button  
Numerical keypad keys Select tracks  
+
Pitch “+” button  
F7  
Reserved  
Pitch “–” button  
F8  
TIME button  
Increments track selection  
Decrements track selection  
/
,
F9  
PITCH button  
F10  
F11  
F12  
PROG.PLAY ON/OFF button  
CAPS/NUM button  
END MON/CLEAR button  
Esc  
Cancels track selected with numerical keypad keys  
Enter “PUSH ENTER” operation  
NOTE:  
Set the “Pitch” presetting to a setting other than “OFF” if you  
wish to change the pitch from the keyboard.  
36  
ENGLISH  
• When editing names  
• Hot start (optional function) data is load  
Esc  
_
F1  
F2  
F3  
F4  
F5  
F6  
F7  
F8  
F9  
_
F10  
F11  
F12  
Print  
Scrol  
Pause  
Esc  
_
F1  
F2  
F3  
F4  
F5  
F6  
F7  
F8  
F9  
_
F10  
F11  
F12  
Print  
Scrol  
Pause  
!
1
@
2
#
3
$
4
%
5
^
6
&
7
(
9
)
0
+
=
!
1
@
2
#
3
$
4
%
5
^
6
&
7
(
9
)
0
+
=
NumLk  
/
-
NumLk  
/
-
8
J
Backspace  
Ins  
Home  
End  
PgUp  
PgDn  
8
J
Backspace  
Ins  
Home  
End  
PgUp  
PgDn  
{
[
}
]
|
/
7
8
5
2
9
{
[
}
]
|
/
7
8
5
2
9
Tab  
Q
W
Z
E
X
R
C
T
V
Y
B
U
N
I
O
P
Del  
Home  
PgUp  
Tab  
Q
W
Z
E
X
R
C
T
V
Y
B
U
N
I
O
P
Del  
Home  
PgUp  
+
+
:
;
"
`
4
6
:
;
"
`
4
6
Capslock  
Shift  
A
S
D
F
G
H
K
L
Enter  
Capslock  
Shift  
A
S
D
F
G
H
K
L
Enter  
<
,
>
.
?
/
1
End  
3
<
,
>
.
?
/
1
End  
3
M
Shift  
PgDn  
M
Shift  
PgDn  
Enter  
Enter  
0
0
Ctrl  
Alt  
Alt  
Ctrl  
Ins  
Del  
Ctrl  
Alt  
Alt  
Ctrl  
Ins  
Del  
Letter keys  
Input small letters (when CapsLock is off)  
Input numbers  
Number keys  
Hot start 1 to 10  
+
Number keys  
Symbol keys  
Pitch “+” button  
Pitch “–” button  
Input symbols  
Numerical keypad keys  
Input numbers  
+
Inputs “+” symbol  
Inputs “–” symbol  
Inserts character  
Deletes character  
When keys are pressed while holding in the Ctrl key, the keys  
functions as follows:  
Ins  
Number keys  
Reload data 1 to 10  
Del  
When the F11 key is pressed while holding in the Shift key,  
BackSpace  
Deletes previous character  
the hot start data is loaded.  
Moves cursor one step to right  
Moves cursor one step to left  
Cancels name input  
/
,
• In the program mode  
Esc  
Esc  
_
F1  
F2  
F3  
F4  
F5  
F6  
F7  
F8  
F9  
_
F10  
F11  
F12  
Print  
Scrol  
Pause  
Enter Enters input name (“PUSH ENTER” operation)  
!
1
@
2
#
3
$
4
%
5
^
6
&
7
(
9
)
0
+
=
NumLk  
/
-
8
J
Backspace  
Ins  
Home  
End  
PgUp  
PgDn  
{
[
}
]
|
/
7
8
5
2
9
Tab  
Q
W
Z
E
X
R
C
T
V
Y
B
U
N
I
O
P
Del  
Home  
PgUp  
+
:
;
"
`
4
6
Capslock  
Shift  
A
S
D
F
G
H
K
L
Enter  
<
,
>
.
?
/
1
End  
3
M
Shift  
PgDn  
Enter  
0
When keys are pressed while holding in the Shift key, the keys  
Ctrl  
Alt  
Alt  
Ctrl  
Ins  
Del  
functions as follows:  
Input tracks in the program  
Numerical keypad keys  
Letter keys Input capital letters (when CapsLock is off)  
Ins  
Del  
/
Inserts track in program  
Number keys  
Symbol keys  
Input symbols  
Deletes track from program  
Increments track selection  
Decrements track selection  
Input (upper) symbols  
Numerical keypad keys  
Input numbers  
,
Del  
/
Deletes all characters after cursor  
Enter Enter: Set track (“PUSH ENTER” operation)  
Moves cursor to right end of display window  
Moves cursor to left end of display window  
,
When keys are pressed while holding in the Ctrl key, the keys  
functions as follows:  
Del  
/
Deletes all characters  
Moves cursor to final character  
Moves cursor to first character  
,
37  
ENGLISH  
10  
RESETTING THE MICROPROCESSOR  
• A microprocessor controls disc drive unit, operation panel unit and the display.  
• If for some reason the microprocessor should malfunction and the unit becomes inoperable, press the SELECT knob and the STANDBY/CUE  
button at the same time to reset the microprocessor.  
• When the microprocessor is reset, operation is restored to the same status as when the POWER switch is first turned on.  
11  
HANDLING CARTRIDGES  
Discs are stored inside cartridges, so they can be handled easily without worrying about dust or fingerprints. Be careful of the following in order to  
keep recordings in optimum condition.  
(1) Cautions on Handling  
(2) Cautions on Storing  
• Keep cartridges away from magnets and sources of strong  
magnetic forces. (Only for recordable discs)  
• Put cartridges in their cases when carrying them.  
• Do not apply labels other than the ones included when the  
discs are purchased.  
• Always remove cartridges from the set after recording or playing  
them.  
• Do not put cartridges in the following places:  
• Places exposed to direct sunlight.  
• Hot places.  
• Use a soft, dry cloth to wipe any dirt off the surface of the  
cartridge.  
• Humid or dusty places.  
• Do not open the shutter.  
Forcing the shutter open could break it.  
If the shutter is opened, dirt or dust may get inside and  
fingerprints may get on the disc.  
• Do not bend, heat or throw cartridges.  
• Water droplets may form on the surface if cartridges are moved  
suddenly from outside or any cold place to a warm place. If this  
happens, wait awhile before using them.  
38  
ENGLISH  
12  
MESSAGES  
Messages appear on the display when operating the set.  
The meanings of the messages are described below.  
Message  
Description  
,
Indicates that editing was not possible.  
Can tEdit **  
,
Indicates that the track number cannot be incremented by pressing the REC button during recording.  
Recording is not possible because of a problem in the TOC recording enable data.  
Indicates that editing is complete.  
Can tIncrmnt  
,
Can t Rec!  
Complete!  
Cue*  
Indicates that the cue search operation is being performed. (* is the cue number.)  
Displayed at the beginning of the track name if cue signals are set for that track.  
There is no more remaining time on the disc, or there are already 255 tracks on the disc.  
Recording or editing is not possible with pre-mastered discs.  
<Cue>********  
Disc Full  
DiscType Err  
EEPROM Error  
Error **  
Displayed when changing the presettings if there is a problem with the memory storage operation.  
Displayed when a system error occurs.  
Displayed if there is a problem with the memory storage operation when the presettings have been reset  
(initialized).  
InitialError  
Displayed when initializing the presettings.  
Initial Set  
No Data  
No hot start data.  
Indicates that no track name or disc name has been set.  
Indicates that no program has been input.  
No Name  
No Program!  
No Sel.Track  
No Track  
Displayed when the selected track does not exist on the disc.  
Indicates discs containing disc names but no tracks.  
Data other than audio data is input.  
Not Audio!  
Now Cue Src!  
Now H Start!  
Now Program!  
Play Lock!  
PresetProg*!  
Program Full  
Protected  
Cue direct search mode is on.  
Hot start data is loaded.  
This means that a program has been input.  
Displayed when a locked operation is performed when play lock is preset.  
Program is preset. (* - 1 to 3)  
Displayed if you attempt to program a 26 th step.  
Displayed when you attempt to record or edit while the cartridge is in the accidental erasure prevention mode.  
Sound will be recorded monaural.  
Rec Mono  
Sound will be recorded stereo.  
Rec Stereo  
Track Full  
UTOC Write?  
UTOC Writing  
Displayed when you attempt to set the recording mode on a disc containing 255 tracks.  
Displayed when the MODE button is pressed.  
Displayed while the UTOC is being written.  
39  
ENGLISH  
13  
SYSTEM LIMITATIONS  
(1) Track Number Limits  
• Up to 255 tracks can be recorded when recording the tracks  
successively starting from the first track on blank or no-track  
discs. In the following cases, however, the number of tracks  
that can be recorded decreases:  
• When a track with a track name is divided, both of the divided  
tracks are given the same name. However, if the number of  
characters writeable on the disc is near the limit, the second  
track may only have part of the track name.  
When editing has been performed.  
When there are scratches on the disc and tracks have been  
re-recorded.  
• When two tracks with track names are combined, the name of  
the second track is erased.  
(5) Other Limits  
(2) Recording Time Limits  
• In the program play mode, the record mode is not set even  
when the REC button is pressed.  
If the REC button is pressed, “Now Program!” is displayed for  
approximately 1 second, then turns off.  
• In the program play mode, the editing mode is not set even  
when the MODE button is pressed.  
• Recording is performed in units of approximately 2 seconds.  
Sections of less than 2 seconds still take up 2 seconds worth of  
space on the disc, so this decreases the actual recordable time.  
• Scratched sections of discs are automatically eliminated from  
the recording time.  
If the MODE button is pressed, “Now Program!” is displayed  
for approximately 1 second, then turns off.  
• In the editing mode and during hot start loading, the program  
play mode is not set even when the PROGRAM ON/OFF  
button is pressed.  
• Recording is no longer possible once the maximum number of  
tracks is reached, even if they take up less than the maximum  
recordable time. To record on such discs, first erase unneeded  
tracks. When this is done, it is not possible to record for longer  
than the time of the tracks that have been erased.  
• If the REC button is pressed while hot start data is loaded,  
“Now H Start!” is displayed for 5 seconds. If the REC button is  
pressed while “Now H Start!” is displayed, the recording pause  
mode is set. (The hot start data is cleared.)  
• The remaining time on the disc may not increase when short  
tracks (less than approximately 8 seconds) are erased.  
• If there are many emphasis data on/off signals or other similar  
signals in a track, they are treated as divisions between tracks,  
so recording will not be possible regardless of the recording  
time and number of tracks.  
• Track incrementing may not be possible if it is conducted  
(automatically or manually) consecutively within less than 2  
seconds.  
(3) Editing Function Limits  
• It may not be possible to combine a short track with another  
track.  
• Tracks containing cue points cannot be divided or combined.  
(4) Title Function Limits  
• There are limits to the number of characters that can be used in  
disc and track names and to the total number of characters  
used for both. When writing names, the cursor will only move  
by the maximum number of writeable spaces. (after this no  
more characters can be input.)  
Track names:  
Disc names:  
Total:  
Up to 100 characters  
Up to 100 characters  
Up to 1700 characters  
• The number of characters that can be used in track names  
decreases when the following functions are used:  
Cue point function:  
Using one point decreases the  
number of characters that can be  
used by 10.  
Play speed function: Changing the play speed decreases  
the number of characters that can be  
used by 6.  
CAUTION:  
Because cue points are stored on the disc as name inputs, it  
may not be possible to input names if many cue points are set  
on discs with many tracks, and if many names are used it may  
not be possible to store cue points.  
40  
ENGLISH  
14  
SPECIFICATIONS  
GENERAL  
Type:  
MiniDisc Recorder  
Recordable/Playable Discs:  
Playback: Pre-mastered MDs and recordable MDs  
Recording: Recordable MDs  
Recording System:  
Signal Compression System:  
Rotating Speed:  
Magneto-optical overwriting system (Magnetic field modulation)  
ATRAC (Adaptive Transform Acoustic Coding) version 4.0  
Approx. 400 to 900 rpm.  
Recording/playback time:  
74 min. (Stereo), 148 min. (Mono)  
AUDIO SECTION  
Channels:  
2 channels (Stereo), 1 channel (Mono)  
44.1 kHz  
A/D converter: 16 bit, D/A converter: 18 bit  
20 to 20,000 Hz ( 1.0 dB)  
0.015 % or less (Playback, A filter)  
0.035 % or less (Recording, A filter)  
100 dB or higher (Playback, A filter)  
84 dB or higher (Recording, A filter)  
90 dB or higher (Playback, A filter)  
80 dB or higher (Recording, A filter)  
(1 kHz, 0 dB playback)  
Sampling Frequency:  
Quantization Bits:  
Frequency Response:  
Total Harmonic Distortion:  
Signal to Noise Ratio:  
Channel Separation:  
Analog Output:  
Connector:  
XLR connector  
Output Level:  
Monitor Output:  
Analog Input:  
Connector:  
+18 dBs, 600 /ohms  
20 mW or greater (30 to 40 /ohms)  
XLR connector  
Input Level:  
+18 dBs, 10 k/kohms  
Digital Output:  
Connector:  
XLR connector  
Signal Format:  
Output Level:  
Digital Input:  
AES/EBU or IEC-958 Type I  
3 Vp-p or greater, 110 /ohms  
Connector:  
XLR connector  
Signal Format:  
Input Level:  
Variable Pitch Control:  
Audio Start-up Time:  
Frame Search Accuracy:  
AES/EBU or IEC-958 Type I  
3 to 10 Vp-p, 110 /ohms  
8 %  
0.03 second less  
1 frame (1/86 second)  
DIMENSIONS  
Without feet:  
144 (W) x 133 (H) x 401 (D)  
(5-43/64” x 5-15/64” x 15-25/32”)  
144 (W) x 146 (H) x 401 (D)  
With feet:  
(5-43/64” x 5-3/4” x 15-25/32”)  
(Not including feet, dials and terminals)  
WEIGHT  
Recorder unit:  
5.0 kg (11.02 lbs)  
22 W  
POWER CONSUMPTION:  
POWER SUPPLY:  
AC 120 V 10 %, 60 Hz (U.S.A. Canada)  
&
AC 230 V 10 %, 50 Hz (Europe, Asia Others)  
&
ENVIRONMENTAL CONDITIONS  
Operating Temperature:  
Humidity:  
+5 °C to 35 °C  
25 % to 85 %, non condensing  
–20 °C to 60 °C  
Storage Temperature:  
* Specifications and design are subject to change without notice for purpose improvement.  
US and foreign patents licensed from Dolby laboratories Licensing Corporation.  
41  

Motorola MOTOROKR EM35 User Manual
Microsoft Windows 7 Professional QLF 00195 User Manual
LG Electronics P509 User Manual
Keurig Platinum B70 User Manual
Kenwood CD Player KDC U453 User Manual
HP Hewlett Packard DESKJET 710C User Manual
Echo Bear Cat 70050 User Manual
Bunn Coffeemaker SA User Manual
Billy Goat TKD501H User Manual
Autodesk Computer Accessories 15607 010000 5000A User Manual