ETAM36_AU/02.13
B2
B3
B4
B5
B6
B1
B7
B12
B11
B10
B9
B8
D1
D2
C1
C4
C5
C2
C3
D3
D4
D5
D6
C6
D7
D8
2
A6
A1
A8
A7
A5
A2
A3
A9
A4
A7
A10
B
A24 A23
A11
A12
A22
A21
A20
A13
A19
A14
A18
A16
A15
A17
3
1
2
3
4
5
6
7
8
9
10
11
12
16
13
14
15
4
19
20
18
17
21
22B
23
24
22A
28
27A
27B
26
25
32
33
29
30
30
5
DELiVErinG hoT WATEr AnD sTEAM ................................ 14
Delivering hot water .............................................................................14
Changing the quantity of water delivered automatically. .....................15
Steam delivery.......................................................................................15
Tips for using steam to froth milk ..........................................................15
Cleaning the spout after use..................................................................15
conTEnTs
TEchnicAL DATA................................................................6
DisposAL..........................................................................6
inTroDucTion .................................................................7
Symbols used in these instructions..........................................................7
Letters in brackets....................................................................................7
Troubleshooting and repairs ....................................................................7
cLEAninG ....................................................................... 15
Cleaning the coffee grounds container ..................................................15
Cleaning the drip tray and condensate tray ...........................................16
Cleaning the inside of the coffee machine .............................................16
Cleaning the water tank ........................................................................16
Cleaning the coffee spouts.....................................................................16
Cleaning the pre-ground coffee funnel..................................................16
Cleaning the infuser...............................................................................16
Cleaning the milk container...................................................................17
Cleaning the hot water/steam nozzle....................................................17
sAFETY .............................................................................7
Fundamental safety warnings .................................................................7
DEsiGnATED usE ...............................................................7
insTrucTion For usE.......................................................7
DEscripTion ....................................................................8
Description of appliance ..........................................................................8
Description of control panel.....................................................................8
Description of milk container...................................................................8
Description of accessories ........................................................................8
DEscALinG...................................................................... 17
sETTinG WATEr hArDnEss.............................................. 18
Measuring water hardness ....................................................................18
Setting water hardness..........................................................................18
BEForE usE ......................................................................8
Checking the appliance............................................................................8
Installing the appliance ...........................................................................8
Connecting the appliance ........................................................................9
Setting up the appliance..........................................................................9
WATEr soFTEnEr FiLTEr ................................................. 18
Installing the filter.................................................................................18
Removing the filter................................................................................19
Electrical connection (UK only) ..............................................................19
TurninG ThE AppLiAncE on .............................................9
TurninG ThE AppLiAncE oFF ............................................9
DispLAYED MEssAGEs ..................................................... 20
TrouBLEshooTinG ......................................................... 21
MEnu sETTinGs .............................................................. 10
Rinsing ..................................................................................................10
Descaling...............................................................................................10
Install filter............................................................................................10
Replacing the filter (if installed) ............................................................10
Adjust time............................................................................................10
Auto-start..............................................................................................10
Auto-off.................................................................................................10
Auto-standby timer/ auto-off timer ......................................................10
Energy saving ........................................................................................11
Setting the temperature........................................................................11
Setting water hardness..........................................................................11
Setting the language ............................................................................11
Beep ......................................................................................................11
Cup lighting...........................................................................................11
Default values (reset).............................................................................11
Statistics function..................................................................................11
TEchnicAL DATA
Voltage:
220-240 V~ 50/60 Hz max. 10A
Absorbed power:
Pressure:
Max. water tank capacity:
Size: LxHxD:
Cable length:
Weight:
Coffee beans container capacity:
1450W
15 bar
1,3 l
195x325x500 mm
1,80 m
10,8 kg
150 g
The appliance complies with the following EC directives:
MAKinG coFFEE .............................................................. 12
Selecting the coffee taste ......................................................................12
Selecting the quantity of coffee in the cup ............................................12
Coffee selected ......................................................................................12
Quantity in cup (ml) ..............................................................................12
Customising the “my coffee”quantity ...................................................12
Adjusting the coffee mill........................................................................12
Tips for a hotter coffee...........................................................................12
Making coffee using coffee beans..........................................................12
Making coffee using pre-ground coffee .................................................13
•
•
Low Voltage Directive 2006/95/EC and subsequent
amendments;
EMC Directive 2004/108/EC and subsequent amend-
ments
European Stand-by regulation 1275/2008;
Materials and accessories coming into contact with food
conform to European regulation 1935/2004.
•
•
MAKinG MiLK BAsED DrinKs........................................... 13
Filling and attaching the milk container ................................................13
Adjusting the amount of froth ...............................................................13
Making milk based drinks automatically ...............................................14
Clean the milk frother by using the CLEAN button .................................14
Programming the quantity of coffee and milk in the cup for the FLAT
WHITE, CAPPUCCINO, LATTE and MILK buttons ......................................14
DisposAL
In compliance with European directive 2002/96/EC, the ap-
pliance must not be disposed of with household waste, but
taken to an authorised waste separation and recycling cen-
tre.
6
•
•
•
•
Make sure the socket used is freely accessible at all times,
enabling the appliance to be unplugged when necessary.
Unplug directly from the plug only. Never pull the power
cable as you could damage it.
To disconnect the appliance completely, release the main
switch at the side of the appliance by pushing (fig. 2).
If the appliance is faulty, do not attempt to repair. Turn it
off, unplug from the mains socket and contact Customer
Services.
inTroDucTion
Thank you for choosing the ETAM36.365 automatic bean to cup
espresso and cappuccino machine.
We hope you enjoy using your new appliance.
Take a few minutes to read these instructions.
This will avoid all risks and damage to the appliance.
symbols used in these instructions
Important warnings are identified by these symbols.
It is vital to follow these warnings.
•
Iftheplugorpowercableisdamaged, itmustbereplaced
by De’Longhi customer services only to avoid all risk.
Danger!
Failure to observe the warning may result in life threatening
injury by electric shock.
Important!
•
•
Keep all packaging (plastic bags, polystyrene foam) away
from children.
Important!
The appliance is not intended for use by persons (includ-
ing children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concern-
ing use of the appliance by a person responsible for their
safety. Children should be supervised to ensure that they
do not play with the appliance.
Failure to observe the warning could result in injury or damage
to the appliance.
Danger of burns!
Failure to observe the warning could result in burns.
Please note :
This symbol identifies important advice or information for the
user.
Danger: Risk of burns!
This appliance produces hot water and steam may form while
it is in operation.
Avoid contact with splashes of water or hot steam.
Letters in brackets
The letters in brackets refer to the legend in the description of
the appliance on page 2-3.
DEsiGnATED usE
Troubleshooting and repairs
This appliance is designed and made to prepare coffee and heat
drinks.
In the event of problems, first try and resolve them following
the information given in the sections “Displayed messages” on
page 21 and “Troubleshooting”on page 22.
If this does not resolve the problem or you require further in-
formation, you should consult customer services by calling the
number given on the annexed guarantee leaflet.
If your country is not among those listed on the sheet, call the
number given in the guarantee leaflet.
If repairs are required, contact De’Longhi customer services
only.
The addresses are given in the guarantee leaflet provided with
the machine.
All other use is considered improper.
This appliance is not suitable for commercial use.
The manufacturer is not liable for damage deriving from im-
proper use of the appliance.
This is usehold appliance only.
It is not intended to be used in:
•
staff kitchen areas in shops, offices and other working
onments;
•
•
farm houses
by clients in hotels, motels and other residential type en-
vironments
•
bed and breakfast type environments.
sAFETY
Fundamental safety warnings
insTrucTion For usE
Read these instructions carefully before using the appliance.
Danger!
•
Failure to follow these instructions may result in burns or
damage to the appliance.
This is an electrical appliance and may cause electric shock.
You should therefore follow the safety warnings below:
The manufacturer is not liable for damage deriving from
failure to follow these instructions.
•
•
Never touch the appliance with damp hands or feet.
Never touch the plug with damp hands.
7
B9. MiLK button: to deliver a cup of milk
B10. LATTE button: to deliver a latte
B11. cAppuccino button: to deliver a cappuccino
B12. FLAT WhiTE button: to deliver a flat white (When in the
settings menu, press to scroll through the menu items)
Please note:
Keep these instructions. If the appliance is passed to other per-
sons, they must also be provided with these instructions.
DEscripTion
Description of appliance
(page 3 - A )
A1. Top lid
A2. Beans container
Description of milk container
(page 2 - C )
C1. Milk container lid
C2. Froth adjustment and CLEAN dial
C3. Milk container
A3. Pre-ground coffee funnel lid with pressure closure
A4. Pre-ground coffee funnel
A5. Beans container lid
A6. Grinding adjustment dial
A7. Water tank
A8. Water tank extraction handle
A9. Water softener filter housing
A10. Cup warmer shelf
C4. Lid extraction button
C5. Frothed milk spout (adjustable)
C6. Milk intake tube
Description of accessories
(page 2 - D )
D1. Pre-ground coffee measure
D2. Cleaning brush
D3. Water softener filter (certain models only)
D4. Cappuccino maker/hot water spout release button
D5. Cappuccino maker/hot water spout
D6. Power cable
A11. Coffee spout (adjustable height)
A12. Hot water and steam nozzle
A13. Socket for power cable connector
A14. Condensate tray
D7. “Total Hardness Test”indicator paper
D8. Descaler
A15. Cup tray
A16. Drip tray
A17. Drip tray water level indicator
A18. Coffee grounds container
A19. Infuser
A20. Main switch
A21. Infuser door
BEForE usE
checking the appliance
After removing the packaging, make sure the product is com-
plete and undamaged and that all accessories are present.
Do not use the appliance if it is visibly damaged.
Contact De’Longhi Customer Services.
A22. Infuser door catch
A23.
A24.
button: turns the appliance on and off (stand-by)
button: to enable or disable the cup warmer
installing the appliance
Description of control panel
(page 2 - B )
Important!
A number of buttons on the panel have a double function. This is
indicated in brackets in the description.
When you install the appliance, you should follow the safety
warnings below:
B1.
aroma selection button: press to select coffee
•
The appliance gives off heat. After positioning the appli-
ance on the worktop, leave a space of at least 3 cm be-
tween the surfaces of the appliance and the side and rear
walls and at least 15 cm above the coffee machine.
Water penetrating the appliance could cause damage. Do
not place the appliance near taps or sinks.
The appliance could be damaged if the water it contains
freezes. Do not install the appliance in a room where the
temperature could drop below freezing point.
taste
B2.
button: to select coffee quantity
B3. MEnu button to access the menu. (When in the settings
menu, press to exit the menu)
B4. Display: guides the user in using the appliance
•
•
B5.
button: to deliver hot water (When in the settings
menu, press to confirm the selection)
button: to make 1 cup of coffee with the settings
displayed
button: to make 2 cups of coffee with the set-
tings displayed
B6.
B7.
B8:
•
Arrange the power cable in such a way that it cannot be
damaged by sharp edges or contact with hot surfaces
(e.g. electric hot plates).
button: to deliver steam (When in the settings
menu, press to scroll through the menu items)
8
connecting the appliance
softener filter as described in the section“WATER SOFTEN-
ER FILTER” (page 19). If your model is not provided with
a filter, you can request one from De’Longhi Customer
Services.
Important!
Check that the mains power supply voltage corresponds to the
value indicated on the rating plate on the bottom of the ap-
pliance.
Connect the appliance to an efficiently earthed and correctly
installed socket with a minimum current rating of 10A only.
If the power socket does not match the plug on the appliance,
have the socket replaced with a suitable type by a qualified
professional.
TurninG ThE AppLiAncE on
Please note!
Before turning the appliance on, make sure the main switch is
pressed (fig. 2).
Each time the appliance is turned on, it performs an automatic
preheat and rinse cycle which cannot be interrupted. The appli-
ance is ready for use only after completion of this cycle.
setting up the appliance
Please note!
Danger of burns!
•
•
Coffeehasbeenusedtofactorytesttheapplianceanditis
therefore completely normal for there to be traces of cof-
fee in the mill. The machine is, however, guaranteed to be
new.
You should customise water hardness as soon as possible
following the instructions in the section “Setting water
hardness”on page 19.
During rinsing, a little hot water comes out of the coffee spouts
and is collected in the drip tray underneath. Avoid contact with
splashes of water.
•
To turn the appliance on, press the ON-STANDBY
button (fig. 8). The message “Heating up, Please wait” is
displayed.
After heating, the message “RINSING” is displayed. As well as
heating the boiler, the appliance also heats the internal circuits
by circulating hot water.
The appliance is at temperature when the message indicating
the taste and quantity of coffee appears.
1. Plug the power cable connector into the socket at the back
of the appliance and connect the appliance to the mains
electricity supply (fig. 1). Make sure the main switch at
the side of the appliance is pressed (fig. 2).
You must first choose the language (the languages scroll
through at intervals of about 3 seconds):
2. When “English” appears, press and hold the
button (fig. 3) for a few seconds until “English set” is dis-
played.
TurninG ThE AppLiAncE oFF
Whenever the coffee machine is turned off after being used to
make coffee, it performs an automatic rinse cycle.
Follow the instructions indicated on the appliance display:
3. “FILL TANK”: remove the water tank (fig. 4), open the lid
(fig. 5), fill to the MAX line with fresh water (fig. 6), re-
place the lid and put the tank back in the appliance.
4. “INSERT WATER SPOUT”: Check that the hot water spout is
inserted on the nozzle and place a container with a mini-
mum capacity of 100 ml underneath (fig. 7).
Danger of burns!
During rinsing, a little hot water flows from the coffee spouts.
Avoid contact with splashes of water.
To turn the appliance off, press the ON-STANDBY
but
5. “Water delivery Press OK”is displayed;
6. Press the
button to confirm (fig. 3). The appli-
ance delivers water from the spout then goes off auto-
matically.
The coffee machine is now ready for normal use.
Please note!
•
•
When setting up the appliance, you need to make 4/5
cups of coffee or 4/5 cappuccinos before the appliance
starts to give satisfactory results.
To enjoy your coffee even more and improve the perform-
ance of your appliance, we recommend installing a water
9
1. Press the MEnu/Esc button to enter the menu;
2. Press the scrolling arrow (< or >) (fig. 9) until“Auto-start”
is displayed;
MEnu sETTinGs
To access the settings menu, press the button corresponding to
MEnu. Scroll through the menu by pressing the scrolling arrow
(< or >) (fig. 9).
3. Press the
4. Press the
button. “Enable?”is displayed;
button to confirm;
rinsing
5. Press the scrolling arrow (< or >) to choose the hour;
6. Press the button to confirm;
7. Press the scrolling arrow (< or >) (fig. 9) to change the
minutes;
Use this function to deliver hot water from the spout to heat the internal
circuit and make the coffee delivered hotter.
To enable the function, proceed as follows:
1. Press the MEnu/Esc button to enter the menu;
2. Press the scrolling arrow (< or >) (fig. 9) until “Rinsing”is
displayed;
8. Press the
button to confirm;
9. Press the MEnu/Esc button to exit the menu.
Once the time has been confirmed, activation of auto-start
is indicated by the small bell ( ) displayed alongside the
time.
To disable the function:
1. Select auto-start from the menu;
3. Press the
4. Press the
button. “Confirm?”is displayed;
button (fig. 3). Hot water flows out of
the spout, heating the internal circuit and making the cof-
fee delivered hotter.
2. Press the
3. Press the
The small bell ( ) is no longer displayed.
button. “Disable?”is displayed;
button to confirm.
Descaling
For instructions on descaling, see page 18.
install filter
Auto-off
When this function is enabled:
For instructions on how to install the filter, see the section“Wa-
ter softener filter”(page 19).
-
the appliance is automatically turned off completely, re-
leasing the main switch. To turn the appliance on again,
press the main switch (A20) and then the ON/stand-by
button (A23).
replacing the filter (if installed)
For instructions on how to replace the filter, see the section
“Replacing the filter”(page 20).
When this function is disabled:
Adjust time
-
the appliance switches to stand-by; power remains on
and it consumes a minimal amount of electricity.
To turn the appliance on again, press the ON/stand-by
button (A23).
To adjust the time on the display, proceed as follows:
1. Press the MEnu/Esc button to enter the menu;
2. Press the scrolling arrow (< or >) (fig. 9) until“Adjust time”
is displayed;
3. Press the
display;
4. Press the scrolling arrow (< or >) (fig. 8) to change the
hour;
5. Press the
The stand-by time can be modified using “Auto-off timer” (if
“Auto-off” is enabled) or “Auto-standby timer ” (if “Auto-off” is
disabled).
To enable or disable auto-off, proceed as follows:
1. Press the MEnu/Esc button to enter the menu;
2. Press the scrolling arrow (< or >) (fig. 9) until “Auto-
standby timer”(or Auto-off) is displayed;
3. Press the
played;
4. Press the
button (fig. 3). The hours flash on the
button to confirm. The minutes flash;
6. Press the scrolling arrow (< or >) (fig. 9) to change the
minutes;
7. Press the
button. “Enable?” or “Disable?” is dis-
button to confirm.
The time is set: press the MEnu/Esc button to exit the menu.
button to confirm;
5. Press the MEnu/Esc button to exit the menu.
Auto-start
You can set the auto-start time in order to have the appliance
ready at a certain time (for example in the morning) so you can
make coffee immediately.
Auto-standby timer/ auto-off timer
Auto-off can be set so that the appliance goes off after 15 or 30
minutes, or 1, 2 or 3 hours.
To re-programme Auto-off, proceed as follows:
1. Press the MEnu/Esc button to enter the menu;
2. Press the scrolling arrow (< or >) (fig. 9) until “Auto-
standby timer”(or “Auto-off”) is displayed;
Please note!
To enable this function, the time must already be set correctly.
To enable Auto-start, proceed as follows:
10
3. Press the
button;
1. Press the MEnu/Esc button to enter the menu;
2. Press the scrolling arrow (< or >) (fig. 9) until “Set lan-
guage”is displayed;
4. Press the scrolling arrow (< or >) (fig. 9) until the number
of minutes/hours of operation is displayed (15 or 30 min-
utes, or 1, 2 or 3 hours);
3. Press the
button;
5. Press the
6. Press the MEnu/Esc button to exit the menu.
button to confirm;
4. Press the the scrolling arrow (< or >) until the required
language is displayed ;
Auto-off is programmed.
5. Press the
button to confirm;
6. The set language is displayed;
7. Press the MEnu/Esc button to exit the menu.
Energy saving
Use this function to enable or disable energy saving.
When enabled, the function reduces energy consumption in
compliance with European regulations.
To disable (or enable) energy saving, proceed as follows:
1. Press the MEnu/Esc button to enter the menu;
2. Press the scrolling arrow (< or >) (fig. 9) until “Energy
saving”is displayed;
3. Press the
able?”if the function has already been disabled);
4. Press the button to disable (or enable) energy
saving mode;
Beep
This enables or disables the beep emitted by the machine each
time the buttons are pressed or an accessory is inserted/re-
moved. To disable or re-enable the beep, proceed as follows:
1. Press the MEnu/Esc button to enter the menu;
2. Press the scrolling arrow (< or >) (fig. 9) until “Beep” is
displayed;
button. “Disable?” is displayed (or “En-
3. Press the
able?”if disabled);
4. Press the
button. “Disable?” is displayed (or “En-
button to enable or disable the beep;
5. Press the MEnu/Esc button to exit the menu.
When the function is active, “Energy saving”is displayedafter a
period of inactivity.
5. Press the MEnu/Esc button to exit the menu.
cup lighting
This function enables or disables the cup lighting. The lighting
is enabled by default.
Please note!
The lighting comes on each time coffee, cappuccino or milk
based coffee is made and during each rinsing cycle.
To disable or re-enable this function, proceed as follows:
1. Press the MEnu/Esc button to enter the menu;
2. Press the scrolling arrow (< or >) (fig. 9) until “Cup light-
ing”is displayed;
•
•
•
Wheninenergysavingmode,afewsecondselapsebefore
the first coffee, cappuccino or milk based coffee is deliv-
ered as the appliance must heat up again.
To prepare a drink, press any button to exit energy sav-
ing, then press the button corresponding to the drink you
want to make.
3. Press the
able?”if disabled);
button. “Disable?” is displayed (or “En-
If the milk container is attached to the appliance, the en-
ergy saving function is not active.
4. Press the
lighting;
5. Press the MEnu/Esc button to exit the menu.
button to enable or disable the cup
setting the temperature
To modify the temperature of the water used to make the cof-
fee, proceed as follows:
Default values (reset)
1. Press the MEnu/Esc button to enter the menu;
2. Press the scrolling arrow (< or >) (fig. 9) until “Set tem-
perature”is displayed;
This resets all menu settings and programmed quantities back
to the default values (with the exception of the language
which remains as set).
3. Press the
button;
To reset the default values, proceed as follows:
1. Press the MEnu/Esc button to enter the menu;
2. Press the scrolling arrow (< or >) (fig. 9) until “Default
values”is displayed;
4. Press the scrolling arrow (< or >) until the required tem-
perature is displayed (●=low; ●●●●=maximum);
5. Press the
button to confirm;
6. Press the MEnu/Esc button to exit the menu.
3. Press the
4. “Confirm?”is displayed;
5. Press the
button;
setting water hardness
For instructions on setting water hardness, see page 19.
button to confirm and exit.
setting the language
To modify the language of the display, proceed as follows:
statistics function
This displays statistics relating to the machine.
11
To display, proceed as follows:
is displayed.
3. Press and hold the
sage “Program quantity 1 MY COFFEE” is displayed and
coffee delivery begins. Release the button
4. As soon as the coffee in the cup reaches the required level,
1. Press the MEnu/Esc button to enter the menu;
2. Press the scrolling arrow (< or >) (fig. 9) until “Statistics”
is displayed;
button (fig. 15) until the mes-
3. Press the
button;
4. By pressing the scrolling arrow (< or >) (fig. 9), you can
check:
press the
button (fig. 15) again.
The quantity of coffee in the cup set has now been pro-
grammed.
-
-
-
-
-
how many coffees have been made;
the total number of cappuccinos and milk based coffees;
the total number of litres of water delivered;
how many times the machine has been descaled;
how many times the water softener filter has been re-
placed.
Adjusting the coffee mill
The coffee mill is set by default to prepare coffee correctly and
should not require regulating initially.
However, if after making the first few coffees you find that the
coffee is either too weak and not creamy enough or delivery is
too slow (a drop at a time), this can be corrected by adjusting
the grinding adjustment dial (fig. 13).
5. Press the MEnu/Esc button twice to exit the menu.
MAKinG coFFEE
selecting the coffee taste
Please note!
The appliance is set by default to make coffee with a standard
taste.
The grinding adjustment dial must only be turned when the
coffee mill is in operation.
You can also choose one of these tastes:
Extra-mild taste
Mild taste
If the coffee is delivered too slowly or
not at all, turn one click clockwise to-
wards “7”.
Standard taste
Strong taste
Extra-strong taste
To change the taste, press the
For fuller bodied creamier coffee, turn
one click anticlockwise towards “1” (do
not turn more than one click at a time
otherwise the coffee could be delivered a drop at a time).
These adjustments will only be evident after at least 2 cups of
coffee have been delivered.
button (fig. 10) re-
peatedly until the required taste is displayed.
selecting the quantity of coffee in the cup
The appliance is set by default to make a standard quantity of
coffee. To select the quantity of coffee, press the
button (fig. 11) until the message corresponding to the re-
quired quantity of coffee is displayed:
If this adjustment does not obtain the desired result, turn the
dial another click.
Tips for a hotter coffee
For hotter coffee, you should:
•
•
•
•
performarinsecyclebyselectingthe“Rinsing”functionin
the settings menu (page 10)
warm the cups by rinsing them with hot water (using the
hot water function);
increase the coffee temperature in the settings menu
(page 11);
coffee selected
Quantity in cup (ml)
MY COFFEE
Programmable:
from ≃20 to ≃180
SHORT
STANDARD
LONG
≃40
≃60
≃90
≃120
Press the
button to enable the cup warmer (the
symbol is displayed).
EXTRA LONG
Making coffee using coffee beans
customising the “my coffee” quantity
The appliance is set by default to automatically deliver 30 ml
of “my coffee”.
To modify this quantity, proceed as follows:
1. Place a cup under the coffee spouts (fig. 12).
Important!
Do not use caramelised or candied coffee beans as they could
stick to the coffee mill and make it unusable.
1. Fill the container with coffee beans (fig. 14).
2. Place under the coffee spouts:
2. Press the
button (fig. 10) until “MY COFFEE”
12
- 1 cup, if you want 1 coffee (fig. 15);
- 2 cups if you want 2 coffees (fig. 17).
3. Lower the spout as near as possible to the cups (fig. 16).
This makes a creamier coffee .
4. Press the button corresponding to the number of coffees
6. Preparation begins. The amount of coffee selected is dis-
played together with a progress bar which gradually fills
as preparation progresses.
Please note!
If “Energy saving” mode is active, you may have to wait a few
seconds before the first coffee is delivered.
required (1 cup
or 2 cups
).
5. Preparation begins. The amount of coffee selected is dis-
played together with a progress bar which gradually fills
as preparation progresses.
MAKinG MiLK BAsED DrinKs
Please note!
Please note:
•
To avoid producing milk with poor froth or large bubbles,
always clean the milk container lid and hot water nozzle
as described in the section “Cleaning the milk container”
on pages 15 and 18.
•
•
While the machine is making coffee, delivery can be in-
terrupted at any moment by pressing one of the delivery
buttons.
At the end of delivery, to increase the quantity of coffee in
the cup, just press and hold (within 3 seconds) one of the
Filling and attaching the milk container
coffee buttons (
or
).
1. Remove the lid by pressing the release button C4 and at
the same time lifting the lid upwards (fig. 19);
2. Fill the milk container with a sufficient quantity of milk,
not exceeding the MAX level marked on the container (fig.
20). Each mark on the side of the container corresponds
to about 100 ml of milk.
Once the coffee has been made, the appliance is ready to be
used again.
Please note!
•
Various alarm messages could be displayed while using
the machine (FILL TANK, EMPTY GROUNDS CONTAINER,
etc.). Their meaning is explained in the section“Displayed
messages” (page 21).
For hotter coffee, see the section“Tips for a hotter coffee”
(page 13).
Ifthecoffeeisdeliveredadropatatime,tooweakandnot
creamy enough or too cold, read the tips in the “Trouble-
shooting”section on page 22.
Please note!
•
•
For a denser more even froth, you must use skimmed or
partially skimmed milk at refrigerator temperature (about
5°C).
If“Energy saving”mode is enabled, you may have to wait
a few seconds before the drink is delivered.
•
•
3. Make sure the milk intake tube is correctly inserted in the
bottom of the milk container lid (fig. 21).
4. Replace the lid on the milk container and press down-
wards until it clicks in place.
5. Extract the hot water spout by pressing the button on the
spout (fig. 22A)
6. Attach the milk container to the nozzle and push as far as
it will go (fig. 23). The machine emits a beep (if the beep
function is enabled).
Making coffee using pre-ground coffee
Important!
•
•
Neveraddpre-groundcoffeewhenthemachineisofforit
could spread through the inside of the machine and dirty
it. This could damage the appliance.
Never use more than one level measure as it could dirty
the inside of the machine or block the funnel.
7. Place a sufficiently large cup under the coffee and frothed
milk spouts. Adjust the length of the milk spout. To move
it nearer the cup, simply pull it downwards (fig. 24).
8. Follow the instructions below for each function.
Please note!
If you use pre-ground coffee, you can only make one cup
of coffee at a time.
1. Press the aroma selection button
“Pre-ground”is displayed.
(fig. 10) until
Adjusting the amount of froth
Turn the froth adjustment dial to adjust the amount of froth
on the milk delivered while making cappuccino and milk based
coffees.
2. Open the beans container lid, then open and raise the pre-
ground coffee funnel lid.
3. Make sure the funnel is not blocked, then add one level
measure of pre-ground coffee (fig. 18).
Dial
Description
Recommended for…
4. Place a cup under the coffee spouts.
position
5. Press the 1 cup button
(fig. 15).
13
ing underway, Please wait” is displayed, together with a
progress bar which gradually fills as the operation pro-
ceeds. Cleaning stops automatically.
No froth
FLAT WHITE/
MILK (hot milk)
Min. froth
LATTE
4. Turn the dial back to one of the froth selections.
5. Remove the milk container and always clean the steam
nozzle with a sponge (fig. 26).
Max. froth
CAPPUCCINO/
MILK (frothed milk)
Please note!
•
To prepare a number of cappuccinos and milk based cof-
fees, clean the milk container after you have prepared the
last drink only.
Making milk based drinks automatically
The FLAT WHITE, CAPPUCCINO, LATTE and MILK buttons on the
control panel enable these drinks to be prepared automatically.
Proceed as follows:
1. Fill the milk container and attach it as described above.
2. Turn the froth adjustment dial on the milk container lid to
the position corresponding to the required froth.
3. Press the button corresponding to the required drink. The
name of the drink selected is displayed together with a
progress bar which gradually fills as preparation progress-
es.
•
•
The milk container can be kept in the refrigerator.
In some cases, to clean you must wait for the appliance to
heat up.
programming the quantity of coffee and milk in the
cup for the FLAT WhiTE, cAppuccino, LATTE and MiLK
buttons
The appliance is set by default to automatically deliver stand-
ard quantities. To change these quantities, proceed as follows:
1. Place a cup under the coffee spouts and milk spout.
2. Press and hold one of the function buttons until the mes-
sage “Program quantity, PROGRAM MILK”is displayed.
3. Release the button. The appliance starts delivering milk.
4. Once the required quantity of milk has been delivered into
the cup, press the button again.
4. After a few seconds, frothed milk is delivered from the
milk spout into the cup below.
For drinks with coffee, the machine automatically makes
the coffee after delivering the milk.
Please note!
5. The appliance stops delivering milk and, if required for
the drink being prepared, after a few seconds the coffee
is delivered into the cup. “Program quantity, PROGRAM
COFFEE”is displayed.
6. Once the required quantity of coffee has been delivered
into the cup, press the button again. Coffee delivery
stops.
•
•
If you want to interrupt preparation during delivery, press
any button.
At the end of delivery, to increase the quantity of milk or
coffee in the cup, within three seconds, just press and hold
the button corresponding to the cappuccino or milk based
coffee being made.
Do not leave the milk container out of the refrigerator
for long periods. The warmer the milk (5°C is ideal), the
poorer the quality of froth produced.
•
The machine is now reprogrammed with the new milk and cof-
fee quantities.
clean the milk frother by using the cLEAn button
DELiVErinG hoT WATEr AnD sTEAM
Important! Danger of burns
Important! Danger of burns.
When cleaning the internal tubes of the milk container, a little
hot water and steam leak out of the frothed milk spout.
Avoid contact with splashes of water.
Do not leave the appliance unattended while hot water or
steam is being delivered. The spout becomes hot during deliv-
ery. Hold by the handle only.
Please note!
“TURN DIAL TO CLEAN” flashes on the display each time you
use a milk function. To eliminate all milk residues, proceed as
follows:
If“Energy saving”is active, you may have to wait a few seconds
before hot water and steam are delivered.
1. Leave the milk container in the machine (you do not need
to empty it);
2. Place a cup or other recipient under the frothed milk
spout.
Delivering hot water
1. Make sure the hot water spout is attached correctly (fig.
7).
2. Place a container under the spout (as close as possible to
3. Turn the froth adjustment dial to“CLEAN”(fig. 25).“Clean-
14
avoid splashes).
3. Press the
the
button to deliver a little water (fig. 3). Stop
button (fig. 3).“Preparation underway”
the flow of hot water by pressing the
again.
button
is displayed (if required). Then hot water is delivered and
“HOT WATER” is displayed, together with a progress bar
which fills gradually as preparation proceeds.
2. Wait a few minutes for the cappuccino maker to cool
down, then press the button on the hot water spout and
extract it. Hold the spout with one hand and with the
other, turn the cappuccino maker anticlockwise (fig. 22)
and pull downwards to remove.
4. The machine delivers about 250 ml of hot water, then
delivery stops automatically. To interrupt delivery of hot
water manually, press the
button again.
3. Also remove the steam nozzle by pulling it downwards
(fig. 27A).
4. Check the hole shown by the arrow in fig. 27B is not
blocked. If necessary, clean with a pin.
5. Wash all parts of the cappuccino maker thoroughly with a
sponge and warm water.
6. Reinsert the nozzle and replace the cappuccino maker on
the nozzle, pushing it upwards and turning it until it is at-
tached.
changing the quantity of water delivered automatically.
The machine is set by default to automatically deliver 250 ml
of hot water.
To modify these quantities, proceed as follows:
1. Position a container under the spout.
2. Press and hold the
button until “Program quan-
tity HOT WATER”is displayed, then release.
3. When the hot water in the cup reaches the required level,
press the
button again.
The machine is now reprogrammed with the new quantity.
cLEAninG
steam delivery
1. Make sure the hot water spout is attached correctly (fig.
7).
Important!
•
Do not use solvents, abrasive detergents or alcohol to
clean the coffee machine. With De’Longhi superauto-
matic bean to cup espresso and cappuccino machines, you
need not use chemical products to clean the machine.
None of the components of the appliance can be washed
in a dishwasher with the exception of the milk container
(C).
2. Fill a container with the liquid to be heated/frothed and
immerse the spout/cappuccino maker (D5) in the liquid.
3. Press the steam ( ) button. After a few seconds, the
steam to heat the liquid comes out of the cappuccino
maker and “STEAM”is displayed.
4. When the required temperature is obtained, interrupt
steam delivery by pressing the steam ( ) button again.
(You should not discharge steam for more than 3 minutes
at a time).
•
•
Donotusemetalobjectstoremoveencrustationsorcoffee
deposits as they could scratch metal or plastic surfaces.
cleaning the coffee grounds container
When“EMPTY GROUNDS CONTAINER”is displayed, the grounds
container must be emptied and cleaned.
The appliance cannot be used to make coffee until you have
cleaned the grounds container.
Important!
Always stop steam delivery before extracting the container
containing the liquid to avoid burns from splashes.
Even if not full, the empty grounds container message is dis-
played 72 hours after the first coffee has been prepared. For the
72 hours to be calculated correctly, the machine must never be
turned off with the main switch in the 0 position.
Tips for using steam to froth milk
•
•
•
•
Whenchoosingthesizeofthecontainer,bearinmindthat
the liquid doubles or triples in volume.
For a richer denser froth, use skimmed or partially
skimmed milk at refrigerator temperature (about 5°C).
Foracreamierfroth,rotatethecontainerwithslowmove-
ments in an upward direction.
Important! Danger of burns
If you make a number of cappuccinos one after the other, the
metal cup tray becomes hot.
Wait for it to cool down before touching it and handle it from
the front only.
To avoid milk with poor froth or large bubbles, always
clean the spout as described in the following section.
To clean (with the machine on):
cleaning the spout after use
Always clean the spout after use to avoid the build-up of milk
residues and prevent the spout from clogging.
•
•
Remove the drip tray (fig. 28), empty and clean.
Empty the grounds container and clean thoroughly to
remove all residues left on the bottom. This can be done
with the spatula on the brush provided.
1. Place a container under the cappuccino maker and press
15
•
Check the condensate tray and empty if necessary (fig.
cleaning the coffee spouts
29).
1. Clean the coffee spouts regularly with a sponge or cloth
(fig. 32).
2. Check the holes in the coffee spout are not blocked. If nec-
essary, remove coffee deposits with a toothpick (fig. 33).
Important!
When removing the drip tray, the grounds container must be
emptied, even if it contains few grounds.
If this is not done, when you make the next coffees, the
grounds container may fill up more than expected and clog the
machine.
cleaning the pre-ground coffee funnel
Check regularly (about once a month ) that the pre-ground cof-
fee funnel (A4) is not blocked.
If necessary, remove coffee deposits with the brush (D2) sup-
plied.
cleaning the drip tray and condensate tray
cleaning the infuser
Important!
The infuser (A19) must be cleaned at least once a month.
The drip tray is fitted with a level indicator (red) showing the
level of water it contains (fig. 30).
Before the indicator protrudes from the cup tray, the drip tray
must be emptied and cleaned, otherwise the water may over-
flow the edge and damage the appliance, the surface it rests on
or the surrounding area.
Important!
The infuser may not be ex-
tracted when the machine
is on.
1. Make sure the machine
is correctly turned off
(see “Turning off”, page
To remove the drip tray:
1. Remove the drip tray and grounds container (fig. 28);
2. Empty the drip tray and grounds container and wash
them;
34
10).
2. Open the infuser door
3. Check the condensate tray and empty if necessary.
4. Replace the drip tray complete with grounds container.
(fig. 34) on the right side
H
of the appliance.
4. Press the two red release
buttons inwards and at
the same time pull the
infuser outwards (fig.
35).
S
U
P
cleaning the inside of the coffee machine
Danger of electric shock!
35
Before cleaning internal parts, the machine must be turned
off (see “Turning off”) and unplugged from the mains power
supply.
5. Soak the infuser in water for about 5 minutes, then rinse
under the tap.
Never immerse the coffee machine in water.
Important!
RINSE WITH WATER ONLY
NO WASHING UP LIQUID - NO DISH WASHER
Do not use washing up liquid to clean the infuser as it may
damage it.
1. Check regularly (about once a week) that the inside of the
appliance (accessible after removing the drip tray) is not
dirty. If necessary, remove coffee deposits with the brush
supplied and a sponge.
2. Remove the residues with a vacuum cleaner (fig. 31).
6. Use the brush (D2) to remove any coffee residues left in
the infuser housing, visible through the infuser door.
7. After cleaning, replace the infuser by sliding it onto the
internal support, then push the PUSH symbol fully in until
it clicks into place.
cleaning the water tank
1. Clean the water tank (A7) regularly (about once a month)
and whenever you replace the water softener filter (if pro-
vided) with a damp cloth and a little mild washing up liq-
uid.
2. Remove the filter (if present) and rinse with running wa-
ter.
Infuser
support
3. Replace the filter (if provided), fill the tank with fresh wa-
ter and replace the tank.
16
water (see figure).
6. Check that the intake tube and
spout are not clogged with milk
residues.
Please note!
If the infuser is difficult to insert, before insertion, squeeze the
two levers shown in the figure to make it smaller.
7. Replace the dial (lining up the
arrow with the word “INSERT”),
the spout and the milk intake
tube.
8. Place the lid back on the milk
container.
cleaning the hot water/steam nozzle
Each time you prepare milk, clean the nozzle with a sponge to
remove milk residues from the gaskets.
8. Once inserted, make sure the two red buttons have
snapped out.
DEscALinG
Descale the machine when the message “DESCALE” and the
relative symbol “ ”flash on the display.
PUSH
Important!
•
•
Descaler contains acids which may irritate the skin and
eyes. It is vital to follow the manufacturer’s safety warn-
ings given on the descaler pack and the warnings relating
to the procedure to follow in the event of contact with the
skin and eyes.
Use De’Longhi descaler only. Under no circumstances
should you use sulphamic or acetic based descalers. Their
use invalidates the guarantee. Failure to descale the appli-
ance as described above also invalidates the guarantee.
9. Close the infuser door.
10. Replace the water tank.
cleaning the milk container
Clean the milk container each time you prepare milk as de-
scribed below:
1. Remove the lid.
2. Remove the milk
spout and intake
1. Turn the machine on.
2. Press the MEnu/
Esc button to enter
the menu.
3. Press < or > until
“Descale” is dis-
played.
tube.
3. Turn the froth
adjustment dial
clockwise to the
“INSERT” position
(see figure) and pull
off upwards.
B
A
4. Select by press-
ing the
4. Wash all the com-
ponents thoroughly
button: “Confirm?”
is displayed. Press
with hot water and
mild washing-up
liquid. All compo-
nents are dishwash-
the
but-
ton to confirm.
5. “DESCALE”, “EMPTY DRIP TRAY” is displayed, alternating
with“Remove filter”(if the filter is present) and“ADD DES-
CALER PRESS OK”.
6. Empty the water tank (A9) completely and remove the
water softener filter (if present). Empty the drip tray (fig.
29) and grounds container, then put them back in the ap-
pliance.
er safe, placing them in the top
basket of the dishwasher.
Make sure there are no milk
residues on the hollow and
groove under the dial (see
figure alongside). If necessary,
scrape the groove with a toothpick.
5. Rinse inside the froth adjustment dial seat with running
7. Pour the descaler into the tank up to level A (correspond-
17
ing to a 100 ml pack) marked on the back of the tank (fig.
36), then add water (1 litre) up to level B (fig. 36) and put
the water tank back.
soft water ●
slightly hard water ●●
hard water ●●●
very hard water ●●●●
8. Place an empty container with a minimum capacity of 1.5
litres under the hot water spout (fig. 7).
Important! Danger of burns
Hot water containing acid flows out of the hot water spout.
Avoid contact with splashes of water.
setting water hardness
9. Press the
button to confirm that you have added
1. Press the MEnu/Esc button to enter the menu.
2. Press the scrolling arrow (< or >) until “Water Hardness”
is displayed.
the solution. The descale programme automatically per-
forms a series of rinses and pauses to remove limescale
deposits from inside the machine.
3. Press the
button to confirm the selection.
“DESCALE, Please wait” is displayed. The descale pro-
gramme starts and the descaler liquid comes out of the
water spout.
4. Press the scrolling arrow (< or >) repeatedly to set the
level as measured by the indicator paper (see previous
section).
After about 30 minutes, the message“RINSING, INSERT FILTER”
(if previously removed), FILL TANK”is displayed.
10. The appliance is now ready for rinsing through with
clean water. Remove the water tank, empty, rinse under
running water, reinsert the water filter (if previously re-
moved) fill with clean water and replace. “RINSING, Press
OK”is displayed.
5. Press the
button to confirm the setting.
6. Press the MEnu/Esc button to exit the menu.
The machine is now reprogrammed with the new water hard-
ness setting.
WATEr soFTEnEr FiLTEr
Certain models are fitted with a water softener filter. If this is
not the case with your model, you are recommended to pur-
chase one from De’Longhi Customer Services.
11. Empty the container used to collect the descaler solution
and replace it empty under the hot water spout.
12. Press the
button to start rinsing. Hot water flows
To use the filter correctly, follow the instructions below.
out of the spout and the message “RINSING, Please wait”
is displayed.
13. When the water tank is completely empty, the message
“Rinsing complete, Press OK”is displayed.
37
installing the filter
1. Remove the filter from
the packaging.
2. Turn the date indicator
disk (see fig. 37) until
the next two months of
use are displayed.
14. Press the
button.
15. “Heating up, please wait” is displayed: when completed,
the appliance is ready for use.
sETTinG WATEr hArDnEss
Please note
The “DESCALE” message is displayed after a period of time es-
tablished according to water hardness.
The filter lasts about two
months if the appliance is
used normally. If the coffee
machine is left unused with
the filter installed, it will last
a maximum of three weeks.
The machine is set by default for a hardness value of 4.
The machine can also be programmed according to the hard-
ness of the mains water in the various regions so that the ma-
chine needs to be descaled less often.
38
3. To activate the filter, put
it under tap water until
the water overflows the
side openings for more
than one minute (min.
500ml) (fig. 38).
4. Extract the tank from
the appliance and fill
with water.
Measuring water hardness
1. Remove the “TOTAL HARDNESS TEST” indicator paper at-
tached to these instructions from its pack.
2. Immerse the paper completely in a glass of water for one
second.
3. Remove the paper from the water and shake lightly. After
about a minute, 1, 2, 3, or 4 red squares form, depending
on the hardness of the water. Each square corresponds to
one level.
18
5. Place the filter in the
water tank and sub-
merge it completely for
ten seconds, tilting it to
enable the air bubbles
to escape (fig. 39).
9. “Water delivery, Press OK”is displayed.
10. Press the button to confirm the selection. The
appliance begins hot water delivery and the message
“Please wait”is displayed.
11. After delivery, the appliance is automatically ready to make
39
the next drink.
6. Insert the filter into the
filter housing and press
as far as it will go (fig.
40A).
7. Close the tank with the
lid (fig. 40B), and then
replace the tank in the
machine.
When you install the filter,
you must notify the appliance
of its presence.
8. Press the MEnu/Esc
button to enter the
menu;
The new filter is now active and you can use the coffee ma-
chine.
removing the filter
40A
40B
If you want to use the appliance without the filter, you must
remove it and notify the appliance of its removal.
Proceed as follows:
1. Extract the tank and exhausted filter;
2. Press the MEnu/Esc button to enter the menu;
3. Press the scrolling arrow (< or >) (fig. 9) until “Install fil-
ter, Installed”is displayed.
4. Press the
5. The message “Uninstall?”appears on the display;
6. Press the button to confirm and the MEnu/Esc
button to exit the menu.
button;
9. Press the scrolling arrow
(< or >) (fig. 9) until
“Install filter”is displayed.
Electrical connection (uK only)
A) If your appliance comes fitted with a plug, it will incorporate a 13 Amp fuse.
If it does not fit your socket, the plug should be cut off from the mains lead,
and an appropriate plug fitted, as below. WARNING: Very carefully dispose
of the cut off plug after removing the fuse: do not insert in a 13 Amp socket
elsewhere in the house as this could cause a shock hazard. With alternative
plugs not incorporating a fuse, the circuit must be protected by a 15 Amp
fuse. If the plug is a moulded-on type, the fuse cover must be re-fitted
when changing the fuse using a 13 Amp Asta approved fuse to BS 1362.
In the event of losing the fuse cover, the plug must NOT be used until a
replacement fuse cover can be obtained from your nearest electrical dealer.
The colour of the correct replacement fuse cover is that as marked on the
base of the plug.
10. Press the
11. “Install?”is displayed;
12. Press the button to confirm the selection. “Wa-
ter delivery Press OK”is displayed.
button.
13. Position a container under the hot water spout (min. ca-
pacity: 100 ml).
14. Press the
button to confirm the selection. The
appliance begins hot water delivery and the message
“Please wait”is displayed.
15. After delivery, the appliance is automatically ready to make
the next drink.
The filter is now active and you can use the coffee machine.
replacing the filter
B) If your appliance is not fitted with a plug, please follow the instructions
provided below:
WARNING - THIS APPLIANCE MUST BE EARTHED
iMporTAnT
When the symbol “ ” is displayed together with the mes-
sage“REPLACE FILTER”, after two months (see date indicator) or
when the appliance has not been used for 3 weeks, you should
replace the filter:
GREEN AND YELLOW
BLUE
BROWN
EARTH
NEUTRAL
LIVE
1. Extract the tank and exhausted filter;
As the colours of the wires in the mains lead may not correspond with the col-
oured markings identifying the terminals in your plug, proceed as follows:
The green and yellow wire must be connected to the terminal in the plug marked
2. Remove the new filter from the packaging and proceed
following steps from 2 to 6 of the paragraph before.
3. Position a container with a minimum capacity of 100 ml
under the hot water spout.
4. Press the MEnu/Esc button to enter the menu;
5. Press < or > until “Replace filter”is displayed.
with the letter E or the earth symbol
low.
or coloured green or green and yel-
The blue wire must be connected to the terminal marked with the letter N or
coloured black.
The brown wire must be connected to the terminal marked with the letter L or
coloured red.
6. Press the
7. “Confirm?”is displayed;
8. Press the button to confirm the selection;
button;
19
DispLAYED MEssAGEs
DispLAYED MEssAGE
possiBLE cAusE
soLuTion
Insufficient water in the tank.
Fill the tank with water and/or insert it correctly, pushing it
as far as it will go until it clicks into place.
FILL TANK
The grounds container (A18) is full.
Empty the grounds container and drip tray, clean and replace
(fig. 29).
EMPTY GROUNDS CONTAINER
Important: when removing the drip tray, the grounds contai-
ner MUST be emptied, even if it contains few grounds.
If this is not done, when you make the next coffees, the
grounds container may fill up more than expected and clog
the machine.
The grinding is too fine and the coffee is delivered too slowly Repeat coffee delivery and turn the grinding adjustment
GROUND TOO FINE
ADJUST MILL
or not at all.
dial (fig. 13) one click clockwise towards“7”while the coffee
mill is in operation.
If after making at least 2 coffees delivery is still too slow,
repeat the correction procedure, turning the grinding
adjustment dial another click until delivery is correct (see
the section “Adjusting the coffee mill”on page 13).
After cleaning, the grounds container has not been repla- Remove the drip tray and insert the grounds container.
ced.
INSERT GROUNDS CONTAINER
ADD PRE-GROUND COFFEE
DESCALE
The“pre-ground coffee”function has been selected without Place pre-ground coffee in the funnel or deselect the “pre-
placing any pre-ground coffee in the funnel.
ground”function (fig. 18).
The machine must be descaled.
The descaling procedure described in the section “Descaling”
needs to be performed as soon as possible (page 18).
Too much coffee has been used.
REDUCE COFFEE AMOUNT
Select a milder taste by pressing the aroma selection
button (fig. 10) or reduce the quantity of pre-ground coffee.
The coffee beans have run out.
Fill the beans container (fig. 14).
FILL BEANS CONTAINER
The pre-ground coffee funnel is clogged.
Empty the funnel with the help of a brush as described in the
section “Cleaning the pre-ground coffee funnel”.
The infuser has not been replaced after cleaning.
Insert the infuser as described in the section “Cleaning the
infuser”.
INSERT INFUSER ASSEMBLY
The tank is not correctly in place.
Insert the tank correctly and press as far as it will go.
INSERT TANK
The inside of the appliance is very dirty.
Clean the inside of the appliance thoroughly, as described in
the section “Cleaning”. If the message is still displayed after
cleaning, contact customer services.
GENERAL ALARM
The water circuit is empty
Press OK to deliver water from the spout (A11) until it flows
out normally.
WATER CIRCUIT EMPTY FILL
WATER CIRCUIT
Water delivery
PRESS OK
The water softener filter is exhausted.
Replace the filter or remove it as described in the section
“Water softener filter”.
REPLACE FILTER
Milk has been delivered recently and the tubes inside the Turn the froth adjustment dial to CLEAN.
milk container must be cleaned.
TURN DIAL TO CLEAN
The water spout is not inserted or is inserted incorrectly.
The milk container is not inserted correctly.
Descaling is necessary.
Insert the water spout (D5) as far as it will go.
Insert the milk container (fig. 23) as far as it will go.
See par. “DESCALING”.
INSERT WATER SPOUT
INSERT MILK CONTAINER
DESCALE
Replace water filter.
See par. “Replace water filter”.
REPLACE FILTER
20
TrouBLEshooTinG
Below is a list of some of the possible malfunctions.
If the problem cannot be resolved as described, contact customer services.
proBLEM
possiBLE cAusE
soLuTion
The cups were not preheated.
•
Enable the cup warmer, leave the cups at least 20
minutes to warm up.
The coffee is not hot.
•
Warm the cups by rinsing them with hot water
(PLEASE NOTE you can use the hot water function).
The infuser has cooled down because 2/3 minutes Before making the coffee, heat the infuser by rinsing, using
have elapsed since the last coffee was made.
the rinse function (page 10).
A low coffee temperature is set.
Set a higher coffee temperature in the menu.
The coffee is ground too coarsely.
Turn the grinding adjustment dial one click anticlockwise
towards “1”while the coffee mill is in operation (fig. 13).
Continue one click at a time until coffee delivery is satisfac-
tory. The effect is only visible after delivering 2 coffees (see
the section: “Adjusting the coffee mill”on page 13).
The coffee is weak or not creamy
enough.
The coffee is unsuitable.
Use pre-ground coffee for espresso machines only.
The coffee is ground too finely.
Turn the grinding adjustment dial one click clockwise to-
wards “7”while the coffee mill is in operation (fig. 13).
Continue one click at a time until coffee delivery is satisfac-
tory.
The coffee is delivered too slowly or a
drop at a time.
The effect is only visible after delivering 2 coffees (see the
section: “Adjusting the coffee mill”on page 12).
The spouts are blocked.
Clean the spouts with a toothpick (fig. 33B).
Coffee does not come out of one or
both of the spouts.
The milk container lid is dirty.
Clean the milk container lid as described in the section “Cle-
aning the milk container”.
The milk does not
come out of the milk
spout.
The milk is not cold enough or is not semi-skim- Use skimmed or semi-skimmed milk at refrigerator tem-
The milk contains
large bubbles and
squirts out of the
milk spout or there
is little froth.
med.
perature (about 5° C). If the result is not as you wished, try
changing brand of milk.
The froth adjustment dial is incorrectly adjusted.
Adjust following the instructions in the section “Making
cappuccino and milk based coffees”.
The milk container lid or froth adjustment dial Clean the milk container lid and dial as described in the sec-
are dirty
tion “Cleaning the milk container”.
The hot water/steam nozzle is dirty
Clean the nozzle as described in the section “Cleaning the
hot water/steam nozzle”.
The spout is dirty.
Clean as described in the section “Cleaning the spout after
use”.
The milk contains
large bubbles and
squirts out of the
milk spout or there
is little froth.
The connector is not inserted correctly.
Insert the connector as far as it will go in the socket at the
back of the appliance.
The appliance does not come on.
It is not plugged into the mains socket.
The main switch (A20) is not turned on.
The appliance has not been turned off correctly
Plug into the mains socket.
Press the main switch (fig. 2).
The infuser cannot be extracted
Turn the appliance off by pressing the ON-STANDBY
button (page 9)
21
|