Audiovox SP 10CD User Manual

SP-10CD  
MODEL SP-10CD  
10-DISC CD CHANGER  
INSTALLATION MANUAL  
BEFORE INSTALLING THE UNIT  
Transport Lock Screws  
The mechanism in the CD changer is "locked" into place during shipment by the  
transport screws. Be sure to remove the screws prior to installation.  
Caution  
After removing the transport lock screws, place the supplied seals (A) over the screw  
holes. These seals are used to keep dust out of the unit, which could cause a malfuncti
Installation and Wiring Precautions  
To prevent a short-circuit,  
Be sure to turn off the ignition and remove the negative (-) battery cable, prior to installation.  
Connect power wires last.  
1
Note  
If the changer is to be installed in a car that is equipped with an on-board drive or navigation computer, do not disconnect  
the battery cable. If the cable is disconnected, the computer memory may be lost. Under these conditions, use extra  
caution during installation, not to cause a short circuit.  
Do not install the unit in the following locations.  
Locations exposed to direct sunlight.  
2
Where hot air is discharged from the car heater.  
In areas subject to extreme temperatures.  
Incorrect installation can cause the sound to "skip" when playing a disc.  
Mount the unit firmly in place, using the supplied brackets and screws.  
3
Be careful not to damage the car wiring.  
4
Be sure to use the supplied screws.  
Be careful not to snag any wires when tightening screws.  
5
Do not use any of the screws that are part of the brake or steering system, to install the unit.  
This unit cannot be installed on its side, end, or upside down. Installation in such positions will cause malfunctioning  
of the mechanism.  
6
2
INSTALLATION  
The unit can be installed horizontally, vertically or at a 45° angle. The position of the built-in anti-vibration springs (left and right side), must  
correspond to the mounting position chosen. If the springs are not set correctly for the type of installation chosen, the anti-vibration  
compensation will not be effective and vibration may cause the disc to skip.  
CAUTION  
After setting the built-in anti-vibration springs, place the supplied Seals (B) over the holes. These seals are used to keep dust, which could  
cause a malfunction, out of the unit.  
HORIZONTAL INSTALLATION  
Set the 4 anti-vibration springs to  
position "H".  
VERTICAL INSTALLAITON  
Set the 4 anti-vibration springs to  
position "V".  
45° ANGLE INSTALLATION  
Set the 4 anti-vibration springs to  
position "45°".  
position "H"  
position "45°"  
position "V"  
PROCEDURE FOR HORIZONTAL INSTALLATION  
1
Attach bracket (L) and bracket (R) to each side of the unit,  
using the hexagonal bolts with washer base (M5 x 8).  
A n t i - v i b r a t i o n  
springs position  
Bracket (L)  
NOTE: Use seals (A) to cover unused  
mounting holes on sides of unit.  
Hexagonal bolt  
with washer base (M5 x 8)  
Bracket (R)  
2
Determine the mounting location, and drill four mounting  
holes.  
Never mount the unit near the fuel tank.  
Drill holes 4mm in diameter.  
3
Secure the unit in place, using four self-tapping screws  
(M5 x 12).  
Self-tapping screw (M5 x 12)  
Use RTV (silicone sealer) on screw threads or around  
the holes to prevent moisture intrusion.  
Bracket (L)  
Bracket (R)  
3
PROCEDURE FOR VERTICAL INSTALLATION  
Note  
If the anti-vibration spring position has been changed and verified for vertical mounting (as shown on page 3), start with step 2.  
Set the 4 anti-vibration springs to position "V".  
Attach bracket (L) and bracket (R) to each side of the unit,  
using the hexagonal bolts with washer base (M5 x 8).  
1
2
NOTE: Use seals (A) to cover unused  
mounting holes on sides of unit.  
position "V"  
Bracket (L)  
Bracket (R)  
Hexagonal bolt  
with washer base (M5 x 8)  
Determine the mounting location, and drill four mounting  
holes.  
Mount the unit in place, using four self-tapping screws  
(M5 x 12).  
4
3
Use RTV (silicone sealer) on screw threads or around  
the holes to prevent moisture intrusion.  
Never mount the unit near the fuel tank.  
Self-tapping screw  
(M5 x 12)  
Bracket (L)  
Drill holes 4 mm in diameter.  
Bracket (R)  
4
PROCEDURE FOR 45° ANGLE INSTALLATION  
Note  
If the anti-vibration spring position has been changed and verified for 45° angle mounting (as shown on page 3), start with step 2.  
Set the 4 anti-vibration springs to position "45°".  
Attach bracket (L) and bracket (R) to each side of the unit,  
using the hexagonal bolts with washer base (M5 x 8).  
1
2
NOTE: Use seals (A) to cover unused  
mounting holes on sides of unit.  
°"  
Bracket (L)  
Bracket (R)  
Hexagonal bolt  
with washer base (M5 x 8)  
Determine the mounting location, and drill four mounting  
holes.  
Mount the unit in place, using four self-tapping screws  
(M5 x 12).  
4
3
Use RTV (silicone sealer) on screw threads or around  
the holes to prevent moisture intrusion.  
Never mount the unit near the fuel tank.  
Self-tapping screw (M5 x 12)  
Drill holes 4mm in diameter.  
Bracket (L)  
Bracket (R)  
5
VEHICLE WIRING  
Mating 8-pin DIN socket on rear of  
compatible radio chassis (see note 1 below).  
Car Stereo with  
CD Changer Controls  
CD changer  
NOTE: 1. Check with your Audiovox car audio dealer to be  
sure your stereo is directly compatible with this  
CD changer.  
2. Wiring instructions for use with FM Modulator/  
Commander Systems are included with the  
CDC-MC1, CDC-MCR2, P-MC3 and P-MCR4 ac-  
cessories.  
6
© 1999 AUDIOVOX CORP., HAUPPAUGE, NY  
Printed in China  
128-5542  

Motorola MOTO Q CELLPHONE User Manual
Lenovo THINKCENTRE 8175 User Manual
Kompernass KH 2186 User Manual
Hitachi Deskstar 5K3000 User Manual
Hamilton Beach Coffeemaker TE120 User Manual
Hamilton Beach 44241 MX User Manual
Emerson girlpower GP890 User Manual
Curtis SCR1371 User Manual
Chang Yue Industrial KN 8828B User Manual
Agilent Technologies 4287A 03 User Manual