UDWC23 Accessory Camera User’s Manual
What’s in the Box
If any items are
missing or damaged,
contact our Customer
Care Line immediately.
Never use damaged
Camera stand
products!
AC adapter
Portable video camera
If You...
Contact Uniden’s... Phone Number
817-858-2929 or
800-297-1023
have a question or problem
Customer Care Line*
need a replacement part or accessory Parts Department*
800-554-3988
Accessibility Help
800-874-9314
(voice or TTY)
need special help due to a disability
Line
* During regular business hours, Central Standard Time. Visit our website for detailed business
hours.
to make sure that you and your parent or guardian understand these terms, conditions,
and safety warnings.
► Allow for proper ventilation when units are in use. Do not cover the camera or receiver
with any object such as a blanket. Do not place it in a drawer or in any location which
would muffle the sound or interfere with the normal flow of air.
SAVE THESE INSTRUCTIONS!
For best results:
To avoid damage to your equipment, follow these simple precautions:
► Do not drop, puncture or disassemble any part of the equipment. There are no user-
serviceable parts inside.
► Do not expose the equipment to high temperatures, and avoid leaving the equipment in
direct sunlight for more than a few minutes. Heat can damage the case or electrical parts.
► Do not place heavy items on top of the equipment or expose the equipment to heavy
pressure.
► Remove the power adapter during long periods between usages.
► Clean only with a dry cloth.
Failure to follow the instructions in this operating manual will void the warranty.
Uniden assumes no liability for damages to property or injury to persons caused by
improper handling or failure to comply with these safety instructions.
Contents
Getting Started
Connecting the Power
1. Connect one end of
the AC adapter
Battery
to the camera’s
power connector
and the other
end to a standard
120 volt AC
status
Link
status
Power
status
Antenna
Lens
outlet.
2. Press the POWER
button on the
camera; the
POWER
LINK
Power status light
should turn on.
If it doesn’t, try
reconnecting the
AC adapter, and
make sure the
power outlet isn’t
controlled by a
wall switch.
Power
connector
LINK
Stand
Charging the Batteries
The batteries in your camera will charge whenever the power is connected. Let
the batteries charge completely (about 8 hours) before you unplug the camera
to move it around. (You can still use the camera: just keep it plugged in.)
4
Learning the Buttons and Lights
Button
POWER
LINk
What it does
Turn the camera on. Press and hold to turn it off.
Enter pairing mode.
Light
State
On
What it means
The camera is on.
The camera is off.
Power Status
light
Off
Flashing The camera is in pairing mode.
Link Status
light
Orange The camera is connected to the receiver.
Off
Green
Red
Off
The camera is in standby.
The battery is charging.
Battery
Status light
The battery is low; the camera will turn off in 3 minutes.
The battery is fully charged.
Using the Camera Mount
The camera has a built-in stand so you can place it on any flat surface. If you
want to place your camera on a wall or a ceiling (or even if you just want to
secure it to a flat surface), you can use the included camera mount. (You might
want to bring the receiver along when you mount the camera; it’s much easier
to get the camera into the right position when you have the display handy.)
5
Mounting
screw
Camera
brace
1. Hold the base of the mount where you want
to attach it, and mark the location of the
screw holes.
2. Use the included screws and anchors to
attach the base to the wall or ceiling.
3. Attach the camera to the mounting screw.
Tighten it a few turns, then turn it to the
direction you want.
Mounting
post
Post
lock
4. Tighten the camera brace up against the back
of the camera to secure it into place.
5. Unlock the mounting post by turning the
wingnut to the left a few turns.
Screw
holes
ꢀ. Set the mounting post to the correct angle,
then tighten the wingnut until the post is
locked into place.
Attach the camera
1
Tighten the brace against
the camera to
secure it
to the mounting
screw and turn it
to the desired
direction.
2
in place.
3
Loosen the
wingnut to
unlock the
mounting
post.
Adjust the post to
the correct angle,
then tighten the
wingnut to lock the
post into place.
4
ꢀ
Pairing the Camera
Before you can use the camera, you’ll need to “introduce” or pair it to the
receiver so they can communicate. You might also perform the pairing
procedure if you are having trouble with the camera.
1. Make sure the camera is powered on.
2. On the receiver, select the channel you want to pair this camera to, and put
the receiver into pairing mode. (This process is slightly different on each
receiver. See the manual that came with your receiver for instructions.)
3. On the camera, press LINk to put the camera into pairing mode.
4. Switch the receiver to this camera’s channel, and verify that the camera’s
video signal appears on the correct channel. (You might have to enable the
new channel first.)
For more information about pairing a camera to your receiver, see the manual
that came with your receiver.
If...
Try...
- making sure the camera is turned on
- making sure the camera is paired to the
correct channel
the receiver’s signal status
icon shows no bars or the
display says No Signal
- re-pairing the camera and receiver
the signal status icon shows
one or two bars or the video
quality is poor
see the manual that came with your
receiver for tips on improving video quality
there is a lot of static on the see the manual that came with your
receiver receiver for tips on improving video quality
ꢁ
Additional Information
Product Specifications
Radio Frequency Transceiver
RF Frequency
Modulation
2402 Mhz ~ 2483.5 Mhz
GFSK
Spread spectrum
Anti Interference
Data rate
Frequency Hopping
Clean Channel Dynamic Select
2 Mbps
Channel bandwidth
Transmitting range
2 MHz
200 meters/600 feet in an open area (line of sight)
Image Specification
Output Image resolution 640 x 480 (VGA)/ 320 x 240 (QVGA)
Image processing
Exposure
Motion JPEG
Auto
White balance
Auto
Camera Specifications
Weight
110 g
Dimension
115 x 60 x 19 mm
Operating temperature
Battery charging temp.
Input voltage
-10° C (+14° F) to +50° C (122° F )
0° C (32° F) to +45° C (113° F )
100-240 V AC @ 60 or 50 Hz
5 V DC @ 1 Amp
Operating voltage
Power consumption
650 mA max
8
Camera Specifications
Low light solution
Low light sensitivity
Picture sensor
11 IR LEDs, 1 Low light sensor
1-8 lux
OV7725 1/4’ Color CMOS
F3.6mm H:53 V:40
Lens
Polymer-Lithium Battery Warning
CAUTION! Risk of explosion if battery is replaced by an incorrect type!
► This equipment contains a rechargeable polymer-lithium battery.
► Do not attempt to charge the battery in temperatures below 0° C (32° F) or higher than
45° C (113° F )
► Dispose of used batteries according to the instructions.
► Do not open or mutilate the battery.
► Disconnect the battery before shipping this product.
► The rechargeable batteries contained in this equipment may explode if disposed of in a
fire.
► Do not short-circuit the battery.
► Do not charge the rechargeable battery pack used in this equipment with in any charger
other than the one designed to charge this battery pack as specified in the owner's
manual. Using another charger may damage the battery pack or cause the battery pack
to explode.
Rechargeable Batteries Must Be Recycled or Disposed of Properly.
Recycling and Disposal Information
► Do not dispose of electronic devices or any of their components (especially batteries
and LCD displays) in your municipal trash collection.
► Consult your local waste management authority or a recycling organization like
Earthꢂ11.com to find an electronics recycling facility in your area.
► If you are unable to locate proper recycling facilities in your area, please return this
product to Uniden for recycling.
ꢂ
FCC Compliance Information
Part 15 Compliance Statement
This device complies with Part 15 of the FCC Rules. Operation is subjected to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
This equipment has been tested and found to comply with limits for a Class B digital
device, pursuant to Part 15 of the FCC rules and ETSI (EN) 300328. These limits are designed
to provide reasonable protection against harmful interference in residential installations.
This equipment generates, uses, and can radiate radio frequency energy, and if not
installed and used in accordance with the instructions, may cause harmful interference to
radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause interference to radio or television equipment reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
► Reorient or relocate the receiving antenna.
► Move the equipment away from the receiver.
► Plug the equipment into an outlet on a circuit different from that to which the receiver is
connected.
► Consult the dealer or an experienced radio/television technician for additional
suggestions.
CAUTION! Any changes or modifications to this equipment not expressly approved
by the party responsible for compliance could void your authority to operate the
equipment.
RF Exposure Information
The antenna used for this transmitter must be installed to provide a separation distance
of at least 20 cm (ꢁ.ꢂ”) from all persons and must not be collocated or operating in
conjunction with any other antenna or transmitter.
10
IC Compliance Information
Radio Equipment Notice
The term “IC:” before the radio certification number only signifies that Industry Canada
technical specifications were met. Operation is subject to the following two conditions: (1)
this device may not cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device. “Privacy of
communications may not be ensured when using this device”.
CE Compliance Information
Products with CE Marking comply with EMC Directive (2004/108/EC); Low Voltage Directive
(ꢁ3/23/EEC); R&TTE(1ꢂꢂꢂ/5/EC) issued by the Commission of the European Community.
Compliance with these directives implies conformity to the following European Norms:
► EMC: EN 301 48ꢂ
► LVD: EN ꢀ0ꢂ50
► Radio: EN 300 328
One-year Limited Warranty
Important: Evidence of original purchase is required for warranty service.
WARRANTOR: UNIDEN AMERICA CORPORATION (“Uniden”) ELEMENTS OF WARRANTY:
Uniden warrants, for one year, to the original retail owner, this Uniden Product to be free
from defects in materials & craftsmanship with only the limitations or exclusions set out
below.
WARRANTY DURATION: This warranty to the original user shall terminate & be of no further
effect 12 months after the date of original retail sale. The warranty is invalid if the Product
is (A) damaged or not maintained as reasonable or necessary, (B) modified, altered, or used
as part of any conversion kits, subassemblies, or any configurations not sold by Uniden,
(C) improperly installed, (D) serviced or repaired by someone other than an authorized
Uniden service center for a defect or malfunction covered by this warranty, (E) used in
any conjunction with equipment or parts or as part of any system not manufactured by
Uniden, or (F) installed or programmed by anyone other than as detailed by the owner’s
manual for this product.
11
STATEMENT OF REMEDY: In the event that the product does not conform to this warranty
at any time while this warranty is in effect, warrantor will either, at its option, repair or
replace the defective unit & return it to you without charge for parts, service, or any
other cost (except shipping & handling) incurred by warrantor or its representatives in
connection with the performance of this warranty. Warrantor, at its option, may replace
the unit with a new or refurbished unit.
THE LIMITED WARRANTY SET FORTH ABOVE IS THE SOLE & ENTIRE WARRANTY PERTAINING
TO THE PRODUCT & IS IN LIEU OF & EXCLUDES ALL OTHER WARRANTIES OF ANY NATURE
WHATSOEVER, WHETHER EXPRESS, IMPLIED OR ARISING BY OPERATION OF LAW,
INCLUDING, BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE. THIS WARRANTY DOES NOT COVER OR PROVIDE
FOR THE REIMBURSEMENT OR PAYMENT OF INCIDENTAL OR CONSEQUENTIAL DAMAGES.
Some states do not allow this exclusion or limitation of incidental or consequential
damages so the above limitation or exclusion may not apply to you.
LEGAL REMEDIES: This warranty gives you specific legal rights, & you may also have other
rights which vary from state to state. This warranty is void outside the United States of
America & Canada.
PROCEDURE FOR OBTAINING PERFORMANCE OF WARRANTY: If, after following the
instructions in the owner’s manual you are certain that the Product is defective, pack the
Product carefully (preferably in its original packaging). Disconnect the battery from the
Product & separately secure the battery in its own separate packaging within the shipping
carton. The Product should include all parts & accessories originally packaged with the
Product. Include evidence of original purchase & a note describing the defect that has
caused you to return it. The Product should be shipped freight prepaid, by traceable
means, to warrantor at:
Uniden America Service
4ꢁ00 Amon Carter Blvd.
Fort Worth, TX ꢁꢀ155
12
|