CA 160 Installation Instructions
PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED
Installation Precautions:
Roll down window to avoid locking keys in vehicle
during installation
Avoid mounting components or routing wires near
hot surfaces
Avoid mounting components or routing wires near
moving parts
Tape or loom wires under hood for protection and
appearance
Use grommets when routing wires through metal
surfaces
Use a Digital Multi Meter for testing and verifying
circuits. DO NOT USE A TEST LIGHT, OR
"COMPUTER SAFE PROBE" as these can set off air
bags or damage vehicle computers.
Technical Support
For Authorized Dealers - (800) 421-3209
FCC COMPLIANCE
This device complies with Part 15 of the FCC rules and with RSS-210 of Industry Canada.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including any interference that may cause
undesired operation.
Warning! Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
CA- 160 System Layout
4-Pin Auxilliary Port
(Green])
4-Pin Tracking Port
(White)
2-Pin LED Port
(White)
22-Pin Base Harness
4-Pin Receiver Port
(Black)
4-Pin External Sensor Port
(Tan)
2-Pin Valet Port
(Blue)
22 Pin Base Harness
4 Pin Auxiliary Harness (GREEN)
1
2
DOME LIGHT OUTPUT
MANUAL ARM INPUT
BLACK/WHITE
1 CHANNEL 2
2 CHANNEL 3
PINK/BLACK
PINK/GREEN
LT.BLUE/RED
3
4
5
6
7
8
UNLOCK SENSE INPUT
TRUNK PIN INPUT
LT.BLUE/GREEN
BLUE
3 CHANNEL 4
4 CHANNEL 5
PINK/BLUE
PINK/RED
INSTANT TRIGGER INPUT BLUE/WHITE
UNUSED
WHITE/BLUE
GRAY
HOOD PIN INPUT
UNUSED
GRAY/BLACK
NEGATIVE DOOR
TRIGGER
9
GREEN
4 Pin 2nd Sensor Port (TAN)
10 GROUND
BLACK
1 PREWARN
BLUE
11 SIREN OUTPUT (+)
12 PARKING LIGHTS
13 CHANNEL 1
14 MANUAL DISARM INPUT
15
BROWN
WHITE
2 FULL TRIGGER
DK. GREEN
PINK
3 GROUND
4 12 VOLTS
BLACK
RED
LT.BLUE/BLACK
16 POSITIVE DOOR TRIGGER PURPLE
17 UNUSED
BLACK/GRAY
18 HEADLIGHT OUTPUT
19 SONGBIRD OUTPUT
20 HORN OUTPUT
21 UNUSED
LT.GREEN/ORANGE
BROWN/WHITE
BROWN/BLACK
PURPLE/WHITE
ORANGE
22 ARMED OUTPUT
4-Pin Power Harness
3-Pin Door Lock Port
(White)
4 Pin Power Harness
3 Pin Door Lock Harness
NEG LOCK/POS UNLOCK GREEN
1 + 12 VOLTS
RED
1
2
3
STARTER INPUT
(Keyside)
NEG UNLOCK/POS LOCK BLUE
2
3
GREEN
2ND STAGE UNLOCK
BLUE/GREEN
STARTER
OUTPUT(Motor Side)
PURPLE
PINK
4 IGN 1 Input/Output
Fuse Grid
-
-
-
+
+
Recommend 15Amp
+
Programming Options
RF Programmer
The RF Programmer allows you to customize the system to fit the individual needs of the consumer, using
a handheld device capable of transmitting system settings directly to the system control module. The RF
Programmer is broken down into three different programming banks.
1. RF Programmer Bank- The RF Programmer Bank allows you to set up the base features of the
system you are installing. It is very important to understand that the base features of this system can
only be programmed using the RF Programmer. Please refer to the chart below showing factory
default settings to determine what options need to be changed for your system. When using the RF
Programmer to select feature settings is very important to verify that the correct base features remain
at the default settings.
CA-160 RF Programmer Base Features
Default
Feature
Setting
ON
OFF
Security
Remote Start
1 Way/2 Way TX
2 Way TX
2. Feature Bank 1- Feature Bank 1 allows you to turn On/Off customer convenience features.
3. Feature Bank 2- Feature Bank 2 allows you to turn On/Off remote start features.
Manual Feature Programming
After installation is complete it will be necessary to program certain system characteristics that can't be
programmed using the RF Programmer (Shock Sensor settings). In addition all of the customer
convenience features and remote start features.
RF Programmer
Selecting Programmable Features
1. Press the POWER button to turn the system ON.
2. Once powered up the MENU screen will be displayed.
3. Use the UP & DN arrows to scroll through the programmable features. Once you locate the desired
feature to change, press the > arrow to advance to the next screen. You should see the default
setting of the system
4. Press the SET button to scroll through the available settings. Once the desired setting is shown on
the screen, press the < to return to the feature chart selectable options or press SEND to transmit
to the system you are installing.
NOTE: You must access the RF receive bank on Option programming to SEND the selected information
to the CA 160, please refer to the programming section on the next page.
Using the M1 function
The RF Programmer has a memory function that will allow you to store the 4 most common feature
settings.
Once you have selected the settings that you want to store press and hold M1 button for 3 seconds. A
menu will appear which will allow you to select the memory bank you wish to save the desired feature
setting into.
Press the SET button to store the setting into memory. The menu will display "Write to memory X"
To retrieve a stored feature setting, press and release the M1 button. A menu will appear that will allow
you to select the desired memory bank.
Press SET to retrieve the desired stored memory bank. The menu will display "Read from memory X"
CA 160 Programming Guide
Feature Bank 0 - 3 Chirps
Transmitter Programming
Feature Bank 1 - 4 Chirps
RF Programmer Receive Bank
Feature Bank 2 - 5 Chirps
Shock Sensor Programming (W/Transmitter Only)
Lite Touch Adjustment
Full Trigger Adjustment
Lock increases sensitivity, Unlock decreases sensitivity
Lock increases sensitivity, Unlock decreases sensitivity
Feature Bank 3 - 6 Chirps
Extended Lock Pulse
Ignition Controlled Lock
Ignition Controlled Unlock
Headlights
1 LED Flash
1 Second
ON
2 LED Flashes 3 LED Flashes 4 LED Flashes
3.5 Seconds
OFF
1 Sec L, Dbl U/L
30 Sec Lk/1 Sec U/L
UNLOCK ALL
Active w/ARM
Passive
Driver Door Only
OFF
Active w/DISARM Active w/BOTH
OFF
Passive Locks
Active
Active
Passive/Active Arming
Siren/Horn
Passive
Siren/Horn
10mS
Siren
Horn
Horn Output Timing
Custom Code
16mS
30mS
40mS
ON
OFF
2nd Step Unlock
Chirp Delete from TX
Trunk Output Timing
AUX 1 Timing
ON
OFF
ON
OFF
Push & Hold
Push & Hold
Push & Hold
Push & Hold
Push & Hold
20 Sec.
10 Seconds
10 Seconds
10 Seconds
10 Seconds
20 Seconds
20 Seconds
20 Seconds
20 Seconds
Latched
Latched
Latched
Latched
AUX 2 Timing
AUX 3 Timing
AUX 4 Timing
Feature Bank 4 - 7 Chirps
RF Start Chirp
1 LED Flash
OFF
2 LED Flashes 3 LED Flashes 4 LED Flashes
ON
Run Time
5 Minutes
ON Steady
Tachless Mode
>.5V B4 Start
Averaging
.8 Seconds
Gas
10 Minutes
Flashing
15 Minutes
20 Minutes
Running Lights
Tach Mode
Tach Mode
<.5V B4 Start
Preset Time
Voltage Level
Crank Average/Crank Time
Crank Time
1.0 Seconds 1.5 Seconds
2.0 Seconds
Gas/Diesel
10 Sec Delay
During Start
ON
15 Sec Delay
20 Sec Delay
Trans Bypass O/P
Temp Controlled Start
Single/Double Pulse Start
while RS ON
OFF
Until IGN OFF
Single BTN Press Double BTN Press
1. SETUP & PROGRAMMING
Transmitter Programming (3 Chirps)
1. With the door open turn the ignition ON.
2. Press and hold the valet/override button.
3. Within 10 Seconds the system will chirp (3) three Times.
4. Press any one button of each transmitter you wish to program.
5. The system will respond with 1 chirp for each accepted transmitter.
Pressing the override button at anytime during programming will advance to the next bank.
Note: This system has 1 button programming which programs all channels of the system
RF Programmer Receive (4 Chirps)
Note: Using the RF Programmer, program all settings prior to following the steps below.
1. With the door open turn the ignition ON.
2. Press and hold the valet/override button.
3. Within 10 Seconds the system will chirp (3) three times (If in transmitter programming simply press
the valet/override button once to advance to the desired feature bank).
4. Press the valet/override button again, The system will chirp (4) Four times.
5. Press SEND on the RF Programmer to set all features and Setting of this system.
6. The unit will flash the parking lights and emit (2) long chirps indicating a successful program.
Shock Sensor Programming (5 Chirps)
1. With the door open turn the ignition ON.
2. Press and hold the valet/override button.
3. Within 10 Seconds the system will chirp (3) three times (If in RF programming simply press the valet/
override button to advance to the desired feature bank).
4. Use the valet/override button to advance through each option bank. Forshock sensor programming
advance to shock sensor programming bank which is (5) Five chirps.
5. Use the transmitter OPT button to scroll through the selections in each feature bank.
6. Press transmitter LOCK button to increase sensitivity and transmitter UNLOCK button to decrease
sensitivity.
NOTE: There are 64 levels of adjustment for each option. Once the highest/lowest sensitivity are achieved,
the sire/horn will sound an extended pulse to notify that you are at the end of the scale. Decreasing
sensitivity one more step from the lowest end of the scale will shut that zone off.
Manual Feature Bank Programming 3 & 4 (6/7 Chirps) without RF programmer
1. With the door open turn the ignition ON
2. Press and hold the valet/override button.
3. Within 10 Seconds the system will chirp (3) three times (If in shock sensor programming simply
press the valet/override button to advance to the desired feature bank)
4. Use the valet/override button to advance through each option bank. For feature programming advance
to Feature Bank 1 & 2 which is (6) six chirps and (7) seven chirps.
5. Use the transmitter OPT Button to scroll through the selections in each feature bank.
6. Press the transmitter LOCK Button to change the desired feature. The LED will flash indicating the
changed feature.
The system will remain in programming mode as long as the ignition is on and the door is
opened, there is no time limit. To exit programming turn the IGNITION OFF.
1. 4 PIN MAIN POWER HARNESS
Battery Power (RED)
Locate the vehicle’s battery wire(s) at the ignition switch.
Verification: These wires will register voltage in all positions of the ignition switch.
Connect the RED wire to the vehicle’s battery wire.
Note: Remove all 30 Amp fuses until all connections are made.
12 volts Ignition Input/Output (PINK)
Locate the vehicle’s Ignition wire at the ignition switch.
Verification: This wire registers voltage when the key is turned to the ON (or RUN) position. The voltage
does not drop out when the key is turned to the START (or CRANK) position.
Connect the PINK wire to the vehicle’s Ignition wire.
This wire is also used for Ignition 1 Output.
Starter Input (Key Side) (GREEN)
Starter Output (Motor Side) (PURPLE)
Locate the vehicle starter wire.
Verification: This wire registers voltage only when the key is turned to the START position. Cut the vehicle
starter wire in half.
Verification after starter wire is cut:
• KEY SIDE of starter wire registers voltage when the key is turned to the START position.
• MOTOR SIDE of starter wire registers no voltage.
Connect the GREEN wire to the KEY SIDE of the vehicle starter wire at the ignition switch harness.
Connect the PURPLE wire to the MOTOR SIDE of the vehicle starter wire.
2. BASIC INSTALLATION - 22 PIN BASE HARNESS
Dome Light Supervision Output (+/-) (BLACK/WHITE)
Locate the vehicle’s dome light or pin switch wire.
Verification: This wire will register positive voltage or ground when the vehicle's dome is turned ON. Typically
this wire is installed with the door trigger input wire. Refer to NEG/POS door input for reference.
To select Negative or Positive polarity output:
Refer to Fuse Placement Diagram below.
Positive Polarity Output
Negative Polarity Output
(+)
(+)
(-)
(-)
Negative Door Input (GREEN)
Locate the vehicle’s dome light or door pin switch wire.
Verification: This wire will register ground (NEG) when the door is opened and the interior light is on. This
wire will register positive voltage when the door is closed and the interior light is off.
Connect the GREEN wire to the vehicle’s negative door input wire(s).
Positive Door Input (PURPLE)
Locate the vehicle’s dome light or door pin switch wire.
Verification: This wire will register positive voltage(POS) when the door is opened and the interior light is on.
This wire will register ground or "0" Volts when the door is closed and the interior light is off.
Connect the PURPLE wire to the vehicle’s negative door input wire(s).
Chassis Ground Source (BLACK)
Connect the BLACK wire to a solid chassis ground point using a ring terminal and self tapping screw (not
supplied). Scrape away paint from the grounding point to ensure a good connection. The recommended
grounding point is a painted metal surface in the driver’s side kick panel area.
Note: Do not ground the BLACK wire with any other vehicle components.
2. 22 PIN BASE HARNESS CONTINUED
Ground When Armed Output (ORANGE)
This wire will show ground when the system is armed.
This wire is used for controlling window modules or additional sensors.
Headlight Output (LT. GREEN/ORANGE)
Locate the vehicle’s headlight wire.
Verification: This wire will register either positive voltage or ground when the headlights are turned on.
Connect the LT. GREEN/ORANGE to the vehicles headlight wire if the system is negative. (LOW CURRENT
ONLY).
Connecting to a positive headlight output.
Fused +12 Volt
Battery Feed
87
Lt. GREEN/ORANGE Headlight
Output From Control Module
Fused +12 Volt
Battery Feed
87a
85
86
30
To Vehicle Headlight
Wire
Hood Pin Input (GRAY)
Install a Hood Pin Switch and connect to the GRAY wire. This connection is required for Remote Start.
Verification: This wire when connected will register ground when the vehicle hood is opened.
Connect the GRAY wire to the hood pin.
Note: Be sure to loom the wire, and seal the grommet with 3M caulk.
Low Current Horn Output (BROWN/BLACK)
Locate the vehicle’s horn wire at the steering column.
Verification: This wire will rest at positive voltage and register ground when the horn switch is pressed.
Connect the BROWN/BLACK wire to the vehicle’s horn wire.
2. 22 PIN BASE HARNESS CONTINUED
Instant Trigger Input (BLUE/WHITE)
This wire is a GROUND input for an external sensor or secondary pin switch
Verification: This wire when connected will trigger the security system
Siren Output (+) (BROWN)
Locate a suitable mounting location in the engine compartment for the siren, away from moving parts.
With the bell of the siren aiming downwards, secure the siren in place using self tapping screws, being
careful not do drill into any hoses, wiring or components.
Connect the BLACK siren wire to a chassis ground using a ring terminal and self tapping screw (not
supplied).
Route the BROWN siren output wire from the control module through the firewall and connect to the RED
wire on the siren.
Note: Be sure to loom the wire/wires, and seal the grommet with 3M caulk.
Parking Light Output (+/-) (WHITE)
Locate the vehicle’s parking light wire at the vehicle light switch
Verification: This wire will register positive voltage or ground when the vehicle parking light switch is turned
to the ON position.
Positive Polarity Systems:
Connect the WHITE wire to the vehicle’s parking light wire at the light switch. Refer to Fuse Placement
Diagram below
Negative Polarity Systems:
Connect the WHITE wire to the vehicle’s parking light wire at the light switch. Refer to Fuse Placement
Diagram below
Positive Polarity Output
Negative Polarity Output
(+)
(+)
(-)
(-)
2. 22 PIN BASE HARNESS CONTINUED
Manual ARM input (LT. BLUE/RED)
This wire will ARM the security system when a POS or NEG pulse is applied to it from an external device.
Manual DISARM Input (LT. BLUE/BLACK)
This wire will DISARM the security system when a POS or NEG pulse is applied to it from an external device.
Unlock Switch Sense (LT. BLUE/GREEN)
This wire will prevent the system from disarming the security system when a POS or NEG pulse is applied to it
from an external device. This will prevent the system from disarming if it is pulsed at the same time as the LT.
BLUE/BLACK (Manual Disarm Input) wire.
For example: To prevent the system from disarming from the switch on the door. Connect this wire to the unlock
switch or passenger unlock motor wire.
NOTE: Only required if using the factory keyless entry transmitter to arm/disarm this system.
Song Bird Output (BROWN/WHITE) SB1 Accessory required
This wire controls the SB1 accessory (Not Included).
Connect this wire to one of the WHITE/BLACK wires from the SB1.
Trunk Pin Switch Input (-) (BLUE)
Connect the BLUE wire to an optional grounding type trunk pin switch.
Trunk Release Output (+/-) (PINK)
Locate the vehicle’s trunk release wire at the trunk release switch.
Verification: This wire will register either positive voltage or ground when the trunk release is activated.
Positive Polarity Systems:
Connect the PINK wire to the vehicle’s trunk release wire. Refer to Fuse Placement Diagram below.
Negative Polarity Systems:
Connect the PINK wire to the vehicle’s trunk release wire. Refer to Fuse Placement Diagram below
Positive Polarity Output
Negative Polarity Output
(+)
(+)
(-)
(-)
3. 4 PIN ADVANCE CHANNEL HARNESS
Channel 2 (PINK/BLACK)
This wire provides a 500mA negative output capable of driving relays. For Control of optional accessories
(i.e. Power Window/Sunroof,etc.).
To Activate press and hold LOCK & TRUNK. Please refer to the selectable options for timing.
Selectable timing: Push & Hold/10 Seconds/20 Seconds/Press to Latch ON/Press to Latch OFF.
Channel 3 (PINK/GREEN)
This wire provides a 500mA negative output capable of driving relays. For Control of optional accessories
(i.e Power Window/Sunroof,etc.).
To Activate press and hold opt sor 2 seconds. Please refer to the selectable options for timing.
Selectable timing: Push & Hold/10 Seconds/20 Seconds/Press to Latch ON/Press to Latch OFF.
Channel 4 (PINK/BLUE)
This wire provides a 500mA negative output capable of driving relays. For Control of optional accessories
(i.e Power Window/Sunroof,etc.).
To Activate press and hold LOCK & OPT. Please refer to the selectable options for timing.
Selectable timing: Push & Hold/10 Seconds/20 Seconds/Press to Latch ON/Press to Latch OFF.
Channel 5 (PINK/RED)
This wire provides a 500mA negative output capable of driving relays. For Control of optional accessories
(i.e Power Window/Sunroof,etc.).
To Activate press and hold UNLOCK & OPT. Please refer to the selectable options for timing.
Selectable timing: Push & Hold/10 Seconds/20 Seconds/Press to Latch ON/Press to Latch OFF.
4. DOOR LOCKS
Negative Lock Output / Positive Unlock Output (GREEN)
Negative Unlock Output / Positive Lock Output (BLUE)
Negative Second Door Unlock Output (BLUE/GREEN)
The door lock / unlock outputs are designed to control several different types of systems which may require
additional parts. Please review the wire and location chart to see which type of door lock system is in your
vehicle. The most common types are shown in the diagrams below.
Negative Switching and Negative Switching with 2-step unlock feature:
All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock / unlock switch.
Verification: These wires will register ground when the Lock and Unlock switches are activated.
Driver’s Door Unlock: Locate the unlock motor wire directly from the actuator inside the driver’s door.
Verification: This wire will rest at ground and register positive voltage when the driver’s door is unlocked.
Connect the GREEN and BLUE or BLUE/GREEN wires shown in diagram 6 below.
Note: When adding the 2 step unlock feature the BLUE/GREEN 2nd door unlock wire will be used to unlock
all vehicle doors on the second press of unlock. An additional SPDT relay (not supplied) (Code Alarm part
HDRLY) is required. Connect the relay as shown in diagram 7 to unlock the driver’s door on the first press
of unlock.
Diagram 6
Door Lock Switch
GREEN (-) Lock Output
Lock
Vehicle Door Lock
Control Relays
Unlock
BLUE (-) Unlock Output Or BLUE/GREEN
(-) 2nd Door Unlock Output when
Installing The 2-Step Unlock
Diagram 7
Fused +12 Volt
Battery Source
87
87a
BLUE (-) Unlock Output
85
86
30
From Keyless Entry
Module Or Door
Lock/Unlock Relays
To Unlock Side Of
Driver's Door Actuator
X
CUT
4. DOOR LOCKS
Negative Lock Output / Positive Unlock Output (GREEN)
Negative Unlock Output / Positive Lock Output (BLUE)
Negative Second Door Unlock Output (BLUE/GREEN)
Positive Switching and Positive Switching with 2-step unlock feature:
All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock / unlock switch.
Verification: These wires will register positive voltage when the Lock and Unlock switches are activated.
Driver’s Door Unlock: Locate the unlock motor wire directly from the actuator inside the driver’s door.
Verification: This wire will rest at ground and register positive voltage when the driver’s door is unlocked.
Connect the GREEN and BLUE or BLUE/GREEN wires shown in diagram 8 below.
Note: When adding the 2 step unlock feature the BLUE/GREEN 2nd door unlock wire will be used to unlock all
vehicle doors on the second press of unlock. Two additional SPDT relays (not supplied) (Code Alarm part
HDRLY) are required. Connect the relays as shown in diagram 9 to unlock the driver’s door on the first
press of unlock.
Diagram 9
Fused +12 Volt
Battery Source
87
Door Lock Switch
BLUE/GREEN
BLUE/RED Second
87a
Door Unlock Trigger
From Control Module
BLUE (+) Lock Output
85
86
30
Lock
Vehicle Door Lock
Control Relays
Unlock
Fused +12 Volt
Battery Source
87
87a
30
GREEN (+) Unlock Output
Chassis Ground
85
86
From Keyless Entry
Module Or Door
Lock/Unlock Relays
To Unlock Side Of
Driver's Door Actuator
X
CUT
4. DOOR LOCKS
Negative Lock Output / Positive Unlock Output (GREEN)
Negative Unlock Output / Positive Lock Output (BLUE)
Negative Second Door Unlock Output (BLUE/GREEN)
Reverse Polarity (5-Wire Doorlocks) and Reverse Polarity with 2-step Unlock:
All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock / unlock switch.
Verification: These wires will rest at ground and register positive voltage when the Lock and Unlock switches
are activated.
Driver’s Door Unlock: Locate the unlock motor wire directly from the actuator inside the driver’s door.
Verification: This wire will rest at ground and register positive voltage when the driver’s door is unlocked.
Connect the GREEN and BLUE or BLUE/GREEN wires shown in diagram 10 below. Use (1) Code Alarm
part DLRK (Door Lock Relay Kit, not supplied) or (2) Code Alarm part HDRLY (SPDT relay, not supplied).
Note: When adding the 2 step unlock feature the BLUE/GREEN 2nd door unlock wire will be used to unlock all
vehicle doors on the second press of unlock. An additional SPDT relay (not supplied) (Code Alarm part
HDRLY) is required. Connect the relays as shown in diagram 11 to unlock the driver’s door on the first
press of unlock
Diagram 10
Fused +12 Volt
Battery Source
87
Master Door
Lock Switch
87a
GREEN (-) Lock Output
85
86
30
To Door Lock
Actuators
Lock
X
Cut
Unlock
Fused +12 Volt
Battery Source
87
BLUE (-) Unlock Output
Or BLUE/GREEN(-) 2nd
Door Unlock Output
87a
85
86
30
To Door Lock
Actuators
X
Cut
Diagram 11
Fused +12 Volt
Battery Source
87
87a
BLUE (-) Unlock Output
85
86
30
From Keyless Entry
Module Or Door
Lock/Unlock Relays
To Unlock Side Of
Driver's Door Actuator
X
CUT
4. DOOR LOCKS
Negative Lock Output / Positive Unlock Output (GREEN)
Negative Unlock Output / Positive Lock Output (BLUE)
Negative Second Door Unlock Output (BLUE/GREEN)
One Wire Negative Multiplexed and One Wire Negative Multiplexed with 2-step Unlock Feature:
All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock / unlock switch.
Verification: This wire will show variable ground when the switch is activated. Please consult the wire and
location chart for specific resistor values for your vehicle.
Driver’s Door Unlock: Locate the unlock motor wire directly from the actuator inside the driver’s door.
Verification: This wire will rest at ground and register positive voltage when the driver’s door is unlocked.
Connect the GREEN and BLUE or BLUE/GREEN wires shown in diagram 12 below. Use (1) Code Alarm
part DLRK (Door Lock Relay Kit, not included) or (2) Code Alarm part HDRLY (SPDT relay, not included).
Note: When adding the 2 step unlock feature the BLUE/GREEN 2nd door unlock wire will be used to unlock all
vehicle doors on the second press of unlock. An additional SPDT relay not supplied (Code Alarm part
HDRLY) is required. Connect the relay as shown in diagram 13 to unlock the driver’s door on the first press
of unlock
Diagram 12
BLUE (-) Unlock Output
Or BLUE/GREEN 2nd
Door Unlock Output When
Installing The 2-Step
Unlock Feature
GREEN (-) Lock Output
Chassis Ground
87
87
Door
Lock Switch
87a
87a
Fused +12 Volt
85
85 Battery Source
86
86
30
30
Lock
Resistor
Resistor
Vehicle Door Lock
Control Relays
Unlock
Diagram 13
Fused +12 Volt
Battery Source
87
87a
BLUE (-) Unlock Output
85
86
30
From Keyless Entry
Module Or Door
Lock/Unlock Relays
To Unlock Side Of
Driver's Door Actuator
X
CUT
4. DOOR LOCKS
Negative Lock Output / Positive Unlock Output (GREEN)
Negative Unlock Output / Positive Lock Output (BLUE)
Negative Second Door Unlock Output (BLUE/GREEN)
One Wire Positive Multiplexed and One Wire Multiplexed With 2-step Unlock Feature:
All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock / unlock switch.
Verification: This wire will show variable positive voltage when the switch is activated. Please consult the
wire and location chart for specific resistor values for your vehicle.
Driver’s Door Unlock: Locate the unlock motor wire directly from the actuator inside the driver’s door.
Verification: This wire will rest at ground and register positive voltage when the driver’s door is unlocked.
Connect the GREEN and BLUE or BLUE/GREEN wires shown in diagram 14 below. Use (1) Code Alarm
part DLRK (Door Lock Relay Kit, not included) or (2) Code Alarm part HDRLY (SPDT relay, not included).
Note: When adding the 2 step unlock feature the BLUE/GREEN 2nd door unlock wire will be used to unlock all
vehicle doors on the second press of unlock. An additional SPDT relay not supplied (Code Alarm part
HDRLY) is required. Connect the relay as shown in diagram 15 to unlock the driver’s door on the first
press of unlock.
Diagram 14
BLUE (-) Unlock Output
Or BLUE/GREEN (-) 2nd
Door Output When
Installing The 2-Step
Unlock Feature
GREEN (-) Lock Output
Fused +12 Volt
Battery Source
87
87
Door
Lock Switch
87a
87a
Fused +12 Volt
85
85 Battery Source
86
86
30
30
Lock
Resistor
Resistor
Vehicle Door Lock
Control Relays
Unlock
Diagram 15
Fused +12 Volt
Battery Source
87
87a
BLUE (-) Unlock Output
85
86
30
From Keyless Entry
Module Or Door
Lock/Unlock Relays
To Unlock Side Of
Driver's Door Actuator
X
CUT
4. DOOR LOCKS
Negative Lock Output / Positive Unlock Output (GREEN)
Negative Unlock Output / Positive Lock Output (BLUE)
Negative Second Door Unlock Output (BLUE/GREEN)
Adding Aftermarket Actuators:
After installing aftermarket actuators, Code Alarm part DA-1 (not supplied). Connect the GREEN and BLUE
wires shown in diagram 16 below. Use (1) Code Alarm part DLRK (Door Lock Relay Kit, not included) or
(2) Code Alarm part HDRLY (SPDT relay, not included).
Diagram 16
Fused +12 Volt
Battery Source
87
Door Lock
Actuator
87a
GREEN (-) Lock Output
85
86
30
Chassis
Ground
M
Fused +12 Volt
Battery Source
87
87a
BLUE (-) Unlock Output
85
86
30
Chassis
Ground
5. ACCESSORY CONNECTOR'S
2 Pin Valet/Program/Override Push-Button Switch: (Blue Connector)
The BLACK and GREY twin lead wires loaded in the two pin blue connector are the ground supply and
program/valet/override input of the Remote Start. Drill a 9/32" hole and mount this switch in an easily
accessible location under the driver's dashboard.
4 Pin Antenna/Receiver Connector: (Black Connector)
Mount the supplied antenna/receiver to a clear spot on the vehicle's winshield that will not block the
driver's vision. A good location is usually high on the winshield near the rear view mirror. Be carefule not
to mount the antenna/receiver on any metallic window film, as this will effect system range. Route the
antenna/receiver cable to the control module and plug into the 4 pin black connector.
4 Pin 2nd Shock Sensor Port: (White Connector)
The RED (+12 volt), BLACK (ground), BLUE (pre-detect) and GREEN (full trigger when armed) wires
loaded into the white connector shell are the inputs/outputs of the shock sensor.
2 Pin LED Harness: (White Connector)
The RED & BLUE wires loaded into the two pin mini white connector control the anode and cathode of
the dash mounted LED. Drill a 1/4" hole and mount the LED in an easy to see location on the
dashboard. Be careful to check to make sure that there is enough clearence behind the panel you are
drilling into.
6. SYSTEM POWER-UP PROCEDURE
1. After all connnections are complete, turn the vehicle's ignition key to the ON position.
2. Insert the 30 Amp fuse into the fuseholder.
3. Turn the ignition key to the OFF position.
7. System Testing
1. Follow each instruction below.
2. Verify that the system operates as indicated under each instruction. Refer to the system owners manual.
3. Check the appropriate wire connection(s) and/or fuse(s) if the unit fails to perform a specific function.
Also check that any options pertaining to the function are programmed properly.
Security Operation
Press LOCK once:
1. Doors lock.
2. Courtesy lights (if on) shut off.
3. Unit checks to see if doors, hood or trunk are open. If open, siren (or horn) sounds once, parking lights
flash once, and system enters pre-arm mode.
Pre-arm mode:
1. The unit will wait for the open door, hood or trunk to be closed. The LED is solid during pre-arm.
2. If the entrance is secured, the siren/horn will sound again, parking lights will flash once, and the system
will arm.
3. If the entrance is not secured after 4 minutes, the siren/horn will sound again, parking lights will flash
once, the system will arm, and the defective trigger or entrance will be ignored.
Note: If entrance is secured after 4 minutes, the system will immediately begin to monitor the entrance for
intrusion.
If the above conditions are not present:
1. Vehicle starter is disabled.
2. Siren (or horn) sounds twice / parking lights flash twice.
3. The LED flashes slowly for duration of arm cycle.
4. After 5 seconds, unit monitors all entrances and sensors.
If door, sensor, hood/trunk or ignition input is triggered:
1. Siren/horn sounds for 30 seconds or until UNLOCK is pressed.
2. Parking lights flash
3. If the system is triggered, pressing DISARM (once) will end the 30-second cycle.
The LED flashes a number of times to indicate which input triggered the alarm:
Number of flashes:
1 - Interior Theft Sensor (Shock Sensor)
2 - Hood/Trunk input
3 - Door Input
7. System Testing Cont.
Press DISARM:
1. Doors unlock.
2. Factory alarm (if equipped) is turned off.
3. Siren/horn sounds once/ parking lights flash once.
4. Courtesy lights turn on for 30 seconds, or until ARM is pressed or ignition is turned on.
5. Vehicle starter is enabled.
.
Press DISARM twice:
1. Passenger doors unlock if using 2-stage unlock.
Press FIND:
Siren/horn sounds 5 times.
Press and hold PANIC for 2 seconds:
Siren/horn sounds and lights flash for 30 seconds or until any remote control button is pressed.
Press and hold TRUNK:
Trunk or hatch opens, or other device activates.
If Ignition Lock option is set to On:
Doors lock when all doors are closed and key is turned to ON position.
If Ignition Unlock option is set to On:
Doors unlock when ignition is turned off.
8. Mounting the Module / Finishing the Installation
1. Mount the module to a brace or wire harness under the dash. The module and harnesses must be clear
of moving parts.
2. Completely uncoil the antenna and route up the nearest front window pillar to the headliner. Be careful not
to pinch the antenna under vehicle panels, or route near moving parts.
3. Route the antenna across the headliner to a position behind the rearview mirror.
4. Attach the antenna to the inside of the windshield behind the rearview mirror:
• The glass surface must be clean before mounting antenna. Use rubbing alcohol to thoroughly clean the
mounting location.
• Remove protective backing and press firmly against windshield.
5. Plug antenna into the Reciever Plug located in the back of module (Black Connector).
Installation Complete
|