Preparing the camera
Before your operation
Shooting images
Interchangeable Lens
Digital Camera
Using the shooting function
Using the viewing function
Changing your setup
Instruction Manual
A-mount
Viewing images on a
computer
Printing images
Others
Index
Additional information on this product and
answers to frequently asked questions can be
found at our Customer Support Website.
Printed using VOC (Volatile Organic
Compound)-free vegetable oil based ink.
Owner’s Record
IMPORTANTSAFETY
INSTRUCTIONS
SAVE THESE
The model and serial numbers are located
on the bottom.
Record the serial number in the space
provided below.
Refer to these numbers whenever you call
upon your Sony dealer regarding this
product.
Model No. SLT-A55/A55V/A33
Serial No. __________________________
INSTRUCTIONS.
DANGER - TO
REDUCE THE RISK
OF FIRE OR
WARNING
To reduce fire or shock hazard, do
not expose the unit to rain or
moisture.
ELECTRIC SHOCK,
CAREFULLY
FOLLOW THESE
INSTRUCTIONS.
If the shape of the plug does not fit the
power outlet, use an attachment plug
adaptor of the proper configuration for the
power outlet.
Caution
Battery pack
If the battery pack is mishandled, the
battery pack can burst, cause a fire or even
chemical burns. Observe the following
cautions.
• Do not disassemble.
• Do not crush and do not expose the
battery pack to any shock or force such as
hammering, dropping or stepping on it.
• Do not short circuit and do not allow
metal objects to come into contact with
the battery terminals.
• Do not expose to high temperature above
60°C (140°F) such as in direct sunlight or
in a car parked in the sun.
• Do not incinerate or dispose of in fire.
• Do not handle damaged or leaking
lithium ion batteries.
• Be sure to charge the battery pack using a
genuine Sony battery charger or a device
that can charge the battery pack.
2
• Keep the battery pack out of the reach of
small children.
• Keep the battery pack dry.
accept any interference received, including
interference that may cause undesired
operation.
• Replace only with the same or equivalent
type recommended by Sony.
This Class B digital apparatus complies
with Canadian ICES-003.
• Dispose of used battery pack promptly
described the instructions.
For Customers in the U.S.A.
Battery charger
UL is an internationally recognized safety
organization.
The UL Mark on the product means it has
been UL Listed.
Even if the CHARGE lamp is not lit, the
battery charger is not disconnected from the
AC power source (mains) as long as it is
connected to the wall outlet (wall socket).
If some trouble occurs while using the
battery charger, immediately shut off the
power by disconnecting the plug from the
wall outlet (wall socket).
When a power cord (mains lead) is
supplied, the power cord (mains lead) can
be used with this unit only, and should not
be used with any other unit.
For Customers in the U.S.A.
and Canada
RECYCLING LITHIUM-ION
BATTERIES
Lithium-Ion batteries are
recyclable.
You can help preserve
our environment by
returning your used
rechargeable batteries to
the collection and
recycling location nearest you.
For more information regarding recycling
of rechargeable batteries, call toll free
1-800-822-8837, or visit http://
www.rbrc.org/
Caution: Do not handle damaged or
leaking Lithium-Ion batteries.
Battery pack
This device complies with Part 15 of the
FCC Rules, Operation is subject to the
following two conditions:
(1) This device may not cause harmful
interference, and (2) this device must
3
If you have any questions about this
product, you may call:
Sony Customer Information Services
Center
1-800-222-SONY (7669)
The number below is for the FCC related
matters only.
Note:
This equipment has been tested and found
to comply with the limits for a Class B
digital device, pursuant to Part 15 of the
FCC Rules.
These limits are designed to provide
reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses, and can
radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does cause
harmful interference to radio or television
reception, which can be determined by
turning the equipment off and on, the user
is encouraged to try to correct the
interference by one or more of the
following measures:
– Reorient or relocate the receiving
antenna.
– Increase the separation between the
equipment and receiver.
– Connect the equipment into an outlet
on a circuit different from that to which
the receiver is connected.
Regulatory Information
Declaration of Conformity
Trade Name: SONY
Model No.: SLT-A55V
Responsible Party: Sony Electronics
Inc.
Address:16530 Via Esprillo,
San Diego, CA 92127 U.S.A.
Telephone No.: 858-942-2230
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) This
device may not cause harmful
interference, and (2) this device must
accept any interference received,
including interference that may cause
undesired operation.
– Consult the dealer or an experienced
radio/TV technician for help.
Declaration of Conformity
Trade Name: SONY
Model No.: SLT-A33
Responsible Party: Sony Electronics
Inc.
Address:16530 Via Esprillo,
San Diego, CA 92127 U.S.A.
Telephone No.: 858-942-2230
The supplied interface cable must be used
with the equipment in order to comply with
the limits for a digital device pursuant to
Subpart B of Part 15 of FCC Rules.
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) This
device may not cause harmful
interference, and (2) this device must
accept any interference received,
including interference that may cause
undesired operation.
CAUTION
You are cautioned that any changes or
modifications not expressly approved in
this manual could void your authority to
operate this equipment.
4
Disposal of Old Electrical &
Electronic Equipment (Applicable in
the European Union and other
European countries with separate
collection systems)
For Customers in Europe
Hereby, Sony Corporation, declares that
this SLT-A55V Interchangeable Lens
Digital Camera is in compliance with the
essential requirements and other relevant
provisions of the Directive 1999/5/EC. For
details, please access the following URL:
http://www.compliance.sony.de/
This symbol on the product or on its
packaging indicates that this product shall
not be treated as household waste. Instead it
shall be handed over to the applicable
collection point for the recycling of
electrical and electronic equipment. By
ensuring this product is disposed of
correctly, you will help prevent potential
negative consequences for the environment
and human health, which could otherwise
be caused by inappropriate waste handling
of this product. The recycling of materials
will help to conserve natural resources. For
more detailed information about recycling
of this product, please contact your local
Civic Office, your household waste
Notice for the customers in the
countries applying EU Directives
The manufacturer of this product is Sony
Corporation, 1-7-1 Konan Minato-ku
Tokyo, 108-0075 Japan. The Authorized
Representative for EMC and product safety
is Sony Deutschland GmbH, Hedelfinger
Strasse 61, 70327 Stuttgart, Germany. For
any service or guarantee matters please
refer to the addresses given in separate
service or guarantee documents.
This product has been tested and found
compliant with the limits set out in the
EMC Directive for using connection cables
shorter than 3 meters (9.8 feet).
disposal service or the shop where you
purchased the product.
Attention
The electromagnetic fields at the specific
frequencies may influence the picture and
sound of this unit.
Notice
If static electricity or electromagnetism
causes data transfer to discontinue midway
(fail), restart the application or disconnect
and connect the communication cable
(USB, etc.) again.
5
Disposal of waste batteries
Notice for customers in the
United Kingdom
(applicable in the European Union
and other European countries with
separate collection systems)
A moulded plug complying with BS 1363
is fitted to this equipment for your safety
and convenience.
Should the fuse in the plug supplied need to
be replaced, a fuse of the same rating as the
supplied one and approved by ASTA or
BSI to BS 1362, (i.e., marked with an
mark) must be used.
or
This symbol on the battery or on the
packaging indicates that the battery
provided with this product shall not be
treated as household waste.
On certain batteries this symbol might be
used in combination with a chemical
symbol. The chemical symbols for mercury
(Hg) or lead (Pb) are added if the battery
contains more than 0.0005% mercury or
0.004% lead.
If the plug supplied with this equipment has
a detachable fuse cover, be sure to attach
the fuse cover after you change the fuse.
Never use the plug without the fuse cover.
If you should lose the fuse cover, please
contact your nearest Sony service station.
By ensuring these batteries are disposed of
correctly, you will help prevent potentially
negative consequences for the environment
and human health which could otherwise be
caused by inappropriate waste handling of
the battery. The recycling of the materials
will help to conserve natural resources.
In case of products that for safety,
performance or data integrity reasons
require a permanent connection with an
incorporated battery, this battery should be
replaced by qualified service staff only.
To ensure that the battery will be treated
properly, hand over the product at end-of-
life to the applicable collection point for the
recycling of electrical and electronic
equipment.
For all other batteries, please view the
section on how to remove the battery from
the product safely. Hand the battery over to
the applicable collection point for the
recycling of waste batteries.
For more detailed information about
recycling of this product or battery, please
contact your local Civic Office, your
household waste disposal service or the
shop where you purchased the product.
6
Notes on using your camera
Shooting procedure
Back up recommendation
• This camera has two modes for shooting:
the LCD monitor mode using the LCD
monitor, and the viewfinder mode using
the viewfinder.
To avoid the potential risk of data loss,
always copy (back up) data to other
medium.
Notes on the LCD monitor, electronic
• The recorded image may be different
from the image you monitored before
recording.
viewfinder, lens, and image sensor
• The LCD monitor and electronic
viewfinder are manufactured using
extremely high-precision technology so
over 99.99% of the pixels are operational
for effective use. However, there may be
some tiny black points and/or bright
points (white, red, blue or green in color)
that constantly appear on the LCD
monitor and electronic viewfinder. These
points are normal in the manufacturing
process and do not affect the images in
any way.
Notes on the functions available with
the camera
• To check whether it is a 1080 60i-
compatible device or 1080 50i-
compatible device, check for the
following marks on the bottom of the
camera.
1080 60i-compatible device:60i
1080 50i-compatible device:50i
• You may feel uncomfortable symptoms
such as eyestrain, nausea, or a tired
feeling while watching 3D-images
recorded with the camera on 3D-
compatible monitors. When you watch
3D-images, we recommend that you take
a break at regular time intervals. Since
the need for or frequency of break times
varies between individuals, please set
your own standards. If you feel sick, stop
watching 3D-images, and consult a
doctor as needed. Also, refer to the
operating instructions of the connected
device or the software used with the
camera. A child’s vision is always
vulnerable (especially for children under
six years of age). Before allowing them
to watch 3D-images, please consult with
an expert, such as a pediatric or
ophthalmic doctor. Be sure to make sure
your children follow the precautions
above.
• When you change your focus on the
viewfinder, red, green, or blue flickers
may appear on the screen. This is not a
malfunction. These flickers are not
recorded on the image.
• Do not hold the camera by taking hold of
the LCD monitor.
• Do not expose the camera to sunlight or
shoot sunward for a long time. The
internal mechanism may be damaged. If
sunlight is focused on a nearby object, it
may cause a fire.
• There is a magnet on the back and around
the rotating shaft of the hinge part of the
LCD monitor. Do not bring anything that
is easily affected by a magnet, such as
floppy disk, credit cards near the LCD
monitor.
• Images may trail across on the screen in a
cold location. This is not a malfunction.
When turning on the camera in a cold
location, the screen may become
temporarily dark. When the camera
warms up, the screen will function
normally.
No compensation for contents of the
recording
The contents of the recording cannot be
compensated for if recording or playback is
not possible due to a malfunction of your
camera or a memory card, etc.
7
Notes on long-time recording
On GPS-compatible devices (SLT-
• When you continue to shoot for a long
time, the temperature of the camera rises.
If the temperature reaches above a certain
A55V only)
• To determine whether your camera
supports GPS function, check the model
name of your camera.
level, the
mark is indicated on the
screen and the camera is turned off
automatically. If the power is turned off,
leave the camera for 10 minutes or longer
to allow the temperature inside the
camera to decrease to a safe level.
• Under high ambient temperatures, the
temperature of the camera rises quickly.
• When the temperature of the camera
rises, the image quality may deteriorate.
It is recommended that you wait until the
temperature of the camera drops before
continuing to shoot.
GPS-compatible: SLT-A55V
GPS-incompatible: SLT-A55/A33
• Use GPS in accordance with regulations
of countries and regions where you use it.
• If you do not record the location
information, set [GPS On/Off] to [Off]
• In an airplane, make sure to turn off the
camera following cabin announcements.
Warning on copyright
Television programs, films, videotapes, and
other materials may be copyrighted.
Unauthorized recording of such materials
may be contrary to the provisions of the
copyright laws.
• The surface of the camera may get hot.
This is not a malfunction.
Notes when playing movies on other
devices
• This camera uses MPEG-4 AVC/H.264
High Profile for AVCHD format
recording. Movies recorded in AVCHD
format with this camera cannot be played
with the following devices.
The pictures used in this manual
The photographs used as examples of
pictures in this manual are reproduced
images, and are not actual images shot
using this camera.
– Other devices compatible with
AVCHD format that does not support
High Profile
– Devices incompatible with the
AVCHD format
On the data specifications described
in this Instruction Manual
The data on performance and specifications
is defined under the following conditions,
except as described in this Instruction
Manual: at an ordinary ambient
temperature of 25ºC (77°F), and using a
battery pack that is charged for about an
hour after the CHARGE lamp goes out.
This camera also uses MPEG-4 AVC/
H.264 Main Profile for MP4 format
recording. For this reason, movies
recorded in MP4 format with this camera
cannot be played on devices other than
those that support MPEG-4 AVC/H.264.
• Discs recorded with HD image quality
(high definition) can be played back only
on AVCHD format-compatible devices.
DVD-based players or recorders cannot
play back HD image quality discs, as
they are incompatible with the AVCHD
format. Also, DVD-based players or
recorders may fail to eject HD image
quality discs.
8
12
Preparing the camera
Checking the accessories supplied
The number in parentheses indicates the number of pieces.
• BC-VW1 Battery charger (1)
• Eyecup (1) (Attached on the
camera)
• CD-ROM (Application Software
for α camera) (1)
• Instruction Manual (This manual)
(1)
• Power cord (mains lead) (1) (not
supplied in the U.S.A. and
Canada)
• Rechargeable battery pack NP-
FW50 (1)
• USB cable (1)
• Shoulder strap (1)
• Body cap (1) (Attached on the
camera)
13
Identifying parts
See the pages in parentheses for details of operation.
Front side
D Remote sensor
F Lens contacts*
G Mirror*
* Do not directly touch these
parts.
** Do not cover this part
during movie recording.
I Mount
K Microphone**
M
(Flash pop-up) button (96)
14
Rear side
A Microphone**
N Speaker
Image sensor position
mark (87)
O
P D-RANGE (Dynamic range)
button (107)
Q For shooting: AEL (AE lock)
For viewing:
button (124)
(Zoom in)
(Exposure)
R For shooting:
button (101)
For viewing:
button (124)/
button (125)
I
(Playback) button (121)
(Zoom out)
(Image index)
K For shooting: Focus Magnifier
For viewing: (Delete) button
S For shooting: Fn (Function)
For viewing:
(Image
rotation) button (123)
15
Sides/Bottom
• Use a tripod with a screw length
of less than 5.5 mm (7/32 inch).
You will be unable to firmly
secure the camera to tripods
having screws longer than 5.5
mm (7/32 inch), and may
A REMOTE terminal
• When connecting the RM-
S1AM/RM-L1AM Remote
Commander (sold separately) to
the camera, insert the plug of
the Remote Commander into
the REMOTE terminal,
aligning the guide of the plug
with the guide of the REMOTE
terminal. Make sure that the
cord of the Remote Commander
faces forward.
damage the camera.
H Battery/memory card cover
I Connection plate cover
D
(USB) terminal (165)
E Microphone jack
• When an external microphone
is connected, the internal
microphone is turned off
automatically. When the
external microphone is a plug-
in-power type, the power of the
microphone is supplied by the
camera.
• For using the AC-PW20 AC
Adaptor (sold separately)
Be careful not to catch the cord
of the AC Adaptor in the cover
when you close the cover.
F Tripod receptacle
17
Charging the battery pack
When using the camera for the first time, be sure to charge the NP-FW50
“InfoLITHIUM” battery pack (supplied).
The “InfoLITHIUM” battery pack can be charged even when it has not
been fully depleted.
It can also be used when it has not been fully charged.
1 Insert the battery pack onto the
battery charger.
Push the battery pack until it clicks.
For the U.S.A and Canada
2 Connect the battery charger to the
Plug
wall outlet (wall socket).
Light on: Charging
Light off: Charge completed
• The CHARGE lamp turns off when
charging is finished.
• Time required to charge a fully
depleted battery pack at a temperature
of 25°C (77°F) is about 250 minutes.
CHARGE lamp
For countries/regions other than the
U.S.A. and Canada
CHARGE lamp
Power cord (mains lead)
18
Notes
• The charging time differs depending on the remaining capacity of the battery back or
charging conditions.
• We recommend charging the battery pack in an ambient temperature of between 10
to 30°C (50 to 86°F). You may not be able to efficiently charge the battery pack
outside of this temperature range.
• Connect the battery charger to the nearest wall outlet (wall socket).
• Do not try to charge the battery pack again right after it has been charged, or when it
has not been used after being charged. Doing so will affect the performance of the
battery pack.
• Do not charge any battery pack other than the “InfoLITHIUM” W series battery
pack in the battery charger (supplied) with your camera. Batteries other than the
specified kind may leak, overheat, or explode if you attempt to charge them, posing a
risk of injury from electrocution and burns.
• When the CHARGE lamp flashes, this may indicate a battery error or that a battery
pack other than the specified type has been installed. Check that the battery pack is
the specified type. If the battery pack is the specified type, remove the battery pack,
replace it with new one or another one and check if the battery charger operates
correctly. If the battery charger operates correctly, a battery error may have
occurred.
• If the battery charger is dirty, charging may not be performed successfully. Clean the
battery charger with dry cloth, etc.
To use your camera abroad — Power sources
You can use your camera and the battery charger and the AC-PW20 AC
Adaptor (sold separately) in any country or region where the power supply
is within 100 V to 240 V AC, 50/60 Hz.
Note
• Do not use an electronic transformer (travel converter), as this may cause a
malfunction.
19
Inserting the battery pack/memory card
(sold separately)
1 While sliding the cover open
lever, open the cover.
2 Firmly insert the battery pack all
the way while pressing the lock
lever with the tip of the battery.
Lock lever
3 Insert a memory card.
• With the notched corner facing as
illustrated, insert the memory card until
it clicks into place.
Ensure the notched corner faces
correctly.
4 Close the cover.
20
Available memory cards
• Only “Memory Stick PRO Duo” media, “Memory Stick PRO-HG Duo”
media, SD memory cards, SDHC memory cards and SDXC memory
cards can be used with this camera. A MultiMediaCard cannot be used
with this camera. However, proper operation cannot be guaranteed for all
memory cards functions.
• The “Memory Stick PRO Duo” media and “Memory Stick PRO-HG
Duo” media are referred to as the “Memory Stick PRO Duo” media and
the SD memory card, SDHC memory card and SDXC memory card are
referred to as the “SD card” in this Instruction Manual.
• For recording movies, it is recommended that you use following memory
cards.
–
(Mark2) (“Memory Stick PRO Duo” media
(Mark2))
–
(“Memory Stick PRO-HG Duo” media)
– SD memory card, SDHC memory card, SDXC memory card (Class 4 or
more)
• Images recorded on an SDXC memory card cannot be imported to or
played on computers or AV devices that are not compatible with exFAT.
Make sure that the device is compatible with exFAT before connecting it
to the camera. If you connect your camera to an incompatible device, you
may be prompted to format the card. Never format the card in response to
this prompt, as doing so will erase all data on the card. (exFAT is the file
system used on SDXC memory cards.)
To remove the battery pack
Turn off the camera and slide the lock
lever in the direction of the arrow. Be
careful not to drop the battery pack.
Lock lever
21
To remove the memory card
Check that the access lamp is not lit, then
open the cover, and push the memory
card once.
Access lamp
To check the remaining battery level
Check the level with the following indicators and percent figures displayed
on the screen.
“Battery
exhausted.”
Battery level
You cannot shoot
any more pictures.
High
Low
What is an “InfoLITHIUM” battery pack?
An “InfoLITHIUM” battery pack is a lithium-ion battery pack that has
functions for exchanging information related to operating conditions with
your camera. Using the “InfoLITHIUM” battery pack, the remaining
battery time in percent figures is displayed according to the operating
conditions of your camera.
Notes on using the battery pack
• The displayed level may not be correct under certain circumstances.
• Do not expose the battery pack to water. The battery pack is not water-
resistant.
• Do not leave the battery pack in extremely hot places, such as in a car or
under direct sunlight.
22
Effective use of the battery pack
• Battery performance decreases in low temperature surroundings. So, the
time that the battery pack can be used is shorter in cold places and the
speed of continuous shooting slows down. We recommend that you put
the battery pack in a pocket close to your body to warm it up, and insert it
in your camera immediately before you start shooting.
• The battery pack will run out quickly if you use the flash frequently, use
continuous shooting often, or turn the camera on and off frequently.
Battery life
• The battery life is limited. Battery capacity decreases little by little as you
use it more and more, and as time passes. If the battery operating time
seems shortened considerably, a probable cause is that the battery pack
has reached the end of its life. Buy a new battery pack.
• The battery life varies according to how it is stored and the operating
conditions and environment in which each battery pack is used.
How to store the battery pack
If the battery pack is not to be used for a long time, charge it and then fully
use it up once a year on your camera before storing the battery pack in a
dry, cool place to prolong the battery life.
Notes on using memory cards
• Do not strike, bend or drop the memory card.
• Do not use or store the memory card under the following conditions:
– High temperature locations such as the hot interior of a car parked in
direct sunlight.
– Locations exposed to direct sunlight.
– Humid locations or locations with corrosive substances present.
• The memory card may be hot just after it has been used for a long time.
Be careful when you handle it.
• When the access lamp is lit, do not remove the memory card or the
battery pack, or turn off the power. The data may be corrupted.
• Data may be damaged if you place the memory card near strongly-
magnetized material or use the memory card in a static-prone or
electrically noisy environment.
23
• We recommend backing up important data, such as to a hard disk of a
computer.
• When you carry or store the memory card, put it in the case supplied with
it.
• Do not expose the memory card to water.
• Do not touch the terminal section of the memory card with your hand or a
metal object.
• When the write-protect switch of a memory card is set to the LOCK
position, you cannot perform operations, such as recording or deleting
images.
• The memory cards formatted with a computer are not guaranteed to
operate with this camera. Be sure to format the memory cards using the
camera.
• Data read/write speeds differ depending on the combination of the
memory cards and the equipment used.
• Do not press down hard when you write down on the memo area.
• Do not attach a label on the memory cards themselves.
• Do not disassemble or modify the memory cards.
• Do not leave the memory cards within the reach of small children. They
might accidentally swallow it.
24
Notes on the “Memory Stick” media used with the camera
The types of “Memory Stick” media that can be used with this camera are
listed in the table below. However, proper operation cannot be guaranteed
for all “Memory Stick PRO Duo” media functions.
“Memory Stick PRO Duo”
media*1*2*3
Available with your camera
“Memory Stick PRO-HG Duo”
media*1*2
“Memory Stick Duo” media
Unavailable with your camera
Unavailable with your camera
“Memory Stick” media and
“Memory Stick PRO” media
*1 This is equipped with MagicGate function. MagicGate is copyright protection
technology that uses encryption technology. Data recording/playback that requires
MagicGate functions cannot be performed with this camera.
*2 Supports high-speed data transfer using a parallel interface.
*3 When using “Memory Stick PRO Duo” media to record movies, only those
marked with Mark2 can be used.
Notes on using “Memory Stick Micro” media (sold separately)
• This product is compatible with “Memory Stick Micro” media (“M2”).
“M2” is an abbreviation for “Memory Stick Micro” media.
• To use a “Memory Stick Micro” media with the camera, be sure to insert
the “Memory Stick Micro” media into an “M2” Adaptor as large as of
Duo size. If you insert a “Memory Stick Micro” media into the camera
without an “M2” Adaptor as large as of Duo size, you might not be able
to remove it from the camera.
• Do not leave the “Memory Stick Micro” media within the reach of small
children. They might accidentally swallow it.
25
Attaching a lens
1 Remove the body cap from the
camera and the packaging lid
from the rear of the lens.
• When changing the lens, quickly
change the lens away from dusty
locations so as to keep dust or debris
from getting inside the camera.
Body cap
Packaging lid
2 Mount the lens by aligning the
orange index marks on the lens
and camera.
Orange index marks
3 Turn the lens clockwise until it
clicks into the locked position.
• Be sure to put the lens on straight.
Notes
• When attaching a lens, do not press the lens release button.
• Do not use force when attaching a lens.
• E-mount lenses are not compatible with this camera.
• When you use a lens for which a tripod socket is provided, attach the lens onto the
tripod using the tripod socket provided to help balance the weight of the lens.
26
To remove the lens
1 Press the lens release button all
the way in and turn the lens
counterclockwise until it stops.
Lens release button
2 Replace the packaging lid on the
lens and attach the body cap to
the camera.
• Before you attach them, remove dust
from them.
• A rear lens cap is not supplied with the DT
18-55mm F3.5-5.6 SAM Lens Kit. When
you store the lens without attaching it to
the camera, purchase the Rear Lens Cap
ALC-R55.
Note on changing the lens
When changing the lens, if dust or debris gets inside the camera and lands
on the surface of the image sensor (the part that acts as the film), it may
appear on the image, depending on the shooting environment.
The camera is equipped with an anti-dust function to prevent dust from
landing on the image sensor. However, quickly change the lens away from
dusty locations when attaching/removing a lens.
If dust or debris lands on the image sensor
Clean the image sensor using [Cleaning Mode] in the Setup menu
27
Preparing the camera
Setting up the date
When you turn the camera on for the first time, the date/time setup screen
appears.
1 Set the power switch to ON to turn
the camera on.
The screen used for setting date and time
appears.
• To turn the camera off, set it to OFF.
2 Verify that [Enter] is selected on
the LCD monitor, then press the
center of the control button.
3 Select your area with b/B on the control button, then press the
center of the control button.
4 Select each item with b/B and
set the numeric value with v/V.
[Daylight Svg.:]: Turns on or off the
daylight saving time setting.
[Date Format:]: Selects the format to
display date.
• Midnight is indicated as 12:00 AM, and
noon as 12:00 PM.
28
5 Repeat step 4 to set other items, then press the center of the
control button.
6 Verify that [Enter] is selected, then press the center of the
control button.
To cancel the date/time setting operation
Press the MENU button.
To set up the date/time again
When you turn the camera on for the first time, the date/time setup screen
appears automatically. The next time, set up the date and time from the
menu.
MENU button t
1 t [Date/Time Setup]
To set up the area again
You can set the area where you are using the camera. This allows you to set
the local area when you use the camera abroad.
MENU button t
1 t [Area Setting]
Maintaining the date and time setting
This camera has an internal rechargeable battery for maintaining the date
and time and other settings regardless of whether the power is on or off, or
the battery is installed or not. For details, see page 192.
Adjusting the focus of the finder (diopter adjustment)
Adjust the diopter-adjustment dial
to your eyesight until the display
appears clearly in the viewfinder.
• Training the camera on a light allows you to
adjust the diopter easily.
Note
• The dioptic adjustment attachment (sold separately) cannot be used with this camera.
29
Using the accessories supplied
This section describes how to use the shoulder strap and eyecup. The other
accessories are described in the following pages.
• Rechargeable battery pack (page 18)
• Battery charger (page 18)
• Power cord (mains lead) (not supplied in the U.S.A. and Canada)
• USB cable (page 165)
• CD-ROM (page 161)
Attaching the shoulder strap
Attach both ends of the strap onto
the camera.
30
Removing the eyecup
When attaching the FDA-A1AM Angle Finder (sold separately) to the
camera, remove the eyecup.
Carefully slide the eyecup off by
pushing on each side of the eyecup.
• Put your fingers under the eyecup, and
slide it upward.
Note
• The Magnifier and Magnifying Eyepiece cannot be used with this camera.
31
Checking the number of recordable
images
Once you insert a memory card into the
camera and set the power switch to ON,
the number of images that can be
recorded (should you continue to shoot
using the current settings) is displayed on
the screen.
Notes
• When “0” (the number of recordable images) flashes in yellow, the memory card is
full. Replace the memory card with another one, or delete images in the current
• When “NO CARD” (the number of recordable images) flashes in yellow, it means
no memory card has been inserted. Insert a memory card.
The number of images that can be recorded on a memory
card
The table shows the approximate number of images that can be recorded on
a memory card formatted with this camera. The values are defined using
Sony standard memory cards for testing. The values may vary depending
on the shooting conditions and the type of memory card used.
Image: Size: L 16M (SLT-A55/A55V)/L 14M (SLT-A33)
Image: Aspect Ratio: 3:2*
“Memory Stick PRO Duo”
SLT-A55/A55V
(Units: Images)
Capacity
2GB
4GB
8GB
16GB
32GB
Size
Standard
386
270
74
781
548
154
220
1587
1116
319
3239
2279
657
6406
4510
1304
1840
Fine
RAW & JPEG
RAW
106
452
928
32
SLT-A33
(Units: Images)
Capacity
2GB
4GB
8GB
16GB
32GB
Size
Standard
433
305
84
875
618
176
251
1778
1258
362
3626
2569
745
7172
5083
1478
2089
Fine
RAW & JPEG
RAW
122
514
1054
* When [Image: Aspect Ratio] is set to [16:9], you can record more images than the
numbers shown in the table above (except when [RAW] is selected).
The number of images that can be recorded using a battery
pack
The approximate number of images that can be recorded is as follows when
you use the camera with the battery pack (supplied) at full capacity.
Note that the actual numbers may be less than those indicated depending on
the conditions of use.
With the flash
SLT-A55
SLT-A55V
SLT-A33
Approx. 390
images
Approx. 380
images
Approx. 340
images
LCD monitor mode
Viewfinder mode
Without the flash
Approx. 350
images
Approx. 330
images
Approx. 270
images
SLT-A55
SLT-A55V
SLT-A33
Approx. 450
images
Approx. 430
images
Approx. 380
images
LCD monitor mode
Viewfinder mode
Approx. 380
images
Approx. 370
images
Approx. 290
images
• The number is calculated with a battery pack at full capacity and in the
following situation:
– At an ambient temperature of 25°C (77°F).
– Using the battery pack that is charged for an hour after the CHARGE
lamp goes out.
– Using Sony “Memory Stick PRO Duo” media (sold separately).
33
– [Image: Quality] is set to [Fine].
– [Autofocus Mode] is set to [Automatic AF].
– Shooting once every 30 seconds.
– The power turns on and off once every ten times.
– [GPS On/Off] is set to [On].
• About the number of images you can shoot when the flash is used:
– The flash strobes once every two times.
– The measurement method is based on the CIPA standard.
(CIPA: Camera & Imaging Products Association)
34
Cleaning
Cleaning the camera
• Do not touch the inside of the camera, such as lens contacts, or the mirror.
Since dust on the mirror or around the mirror may affect the images or the
performance of the camera, blow the dust away using a commercially
available blower*. For details on cleaning the image sensor, see the next
page.
* Do not use a spray blower. Using one may cause a malfunction.
• Clean the camera surface with a soft cloth slightly moistened with water,
then wipe the surface with a dry cloth. Do not use the following as they
may damage the finish or the casing.
– Chemical products such as thinner, benzine, alcohol, disposable cloths,
insect repellent, sunscreen or insecticide, etc.
– Do not touch the camera with the above on your hand.
– Do not leave the camera in contact with rubber or vinyl for a long time.
Cleaning the lens
• Do not use a cleaning solution containing organic solvents, such as
thinner, or benzine.
• When cleaning the lens surface, remove dust using a commercially
available blower. In case of dust that sticks to the surface, wipe it off with
a soft cloth or tissue paper slightly moistened with lens cleaning solution.
Wipe in a spiral pattern from the center to the outside. Do not spray lens
cleaning solution directly onto the lens surface.
35
Cleaning the image sensor
If dust or debris enters the camera and lands on the image sensor (the part
that acts as the film), it may appear on the photo image, depending on the
shooting environment. If there is dust on the image sensor, clean the image
sensor following the steps below.
Notes
• Cleaning cannot be performed when the battery level is 50% or less.
• The camera starts beeping if the battery pack becomes low during cleaning. Stop
cleaning immediately and turn the camera off. The use of an AC-PW20 AC Adaptor
(sold separately) is recommended.
• The cleaning should be completed quickly.
• Do not use a spray blower because it may scatter water droplets inside the camera
body.
To clean the image sensor automatically using the cleaning mode of the
camera
2 Press the MENU button, then
select
2 with b/B on the
control button.
MENU button
3 Select [Cleaning Mode] with v/V,
then press the center of the
control button.
36
4 Select [Enter] with v, and press the center of the control
button.
The image sensor vibrates for a short time, and eliminates dust from the
sensor.
5 Turn off the camera.
To clean the image sensor using a blower
If another cleaning is needed after using the cleaning mode, clean the image
sensor using a blower following the steps below.
3 Push the V mark on the mirror
lock lever with a finger to lift up
the mirror.
• Be careful not to touch the surface of
the mirror.
Mirror lock lever
37
4 Use the blower to clean the image
sensor surface and the
surrounding area.
• Do not touch the image sensor with the
tip of the blower and do not put the tip
of a blower into the cavity beyond the
mount.
• Hold the camera’s face downward to
prevent the dust from resettling in the
camera. Complete the cleaning quickly.
• Also clean the back of the mirror using
a blower.
5 After the cleaning is finished,
lower the mirror with a finger
until it clicks.
• Lower the frame of the mirror back
down with a finger. Be careful not to
touch the surface of the mirror.
• Lower the mirror down until it locks
firmly.
6 Attach the lens and turn the camera off.
• Confirm that the mirror is locked down firmly when you attach the lens.
Notes
• After the cleaning is finished, confirm that the mirror is locked down firmly when
you attach the lens. Otherwise, the lens may be scratched or this may be the cause of
additional trouble. Also, if the mirror is not locked down firmly, the autofocus does
not work during shooting.
• You cannot shoot while the mirror is lifted up.
38
Before your operation
Screen indicators
Switching the screen mode between the LCD monitor and
the electronic viewfinder
FINDER/LCD button
When you look into the viewfinder, the
viewfinder mode is activated, and when
you take your face away from the
viewfinder, the screen mode returns to
the LCD monitor mode.
You can also switch the screen mode
using the FINDER/LCD button.
Viewfinder
LCD monitor
To focus on a subject quickly using the viewfinder
When you look into the viewfinder, the subject located in the AF area
comes into focus automatically (Eye-Start AF).
MENU button t
1 t [Eye-Start AF] t [On]
When the FDA-A1AM Angle Finder (sold separately) is attached to the
camera, setting [Eye-Start AF] to [Off] is recommended because the
eyepiece sensors located below the viewfinder may be activated.
39
Switching the recording information display (DISP)
Each time you press DISP on the control
button, the recording information display
changes as follows.
The status of the screen in the viewfinder
changes as follows (“Recording
information on” (For Live View) is
skipped).
Graphic Display
Recording
information on
(For Live View)
Recording
information off
Digital level gauge
on
Digital level gauge
The digital level gauge of this camera
The digital level gauge indicates whether
the camera is level in both the horizontal
and front-back directions. When the
camera is level in both directions, the
indicator turns to green.
Horizontal direction
Front-back direction
Notes
• The error of the digital level gauge is larger if you tilt the camera too far forward or
backward.
• A tilt of 1° may be indicated even if the camera is almost level.
40
Recording information display (For viewfinder)
You can switch the “Recording information on” display on the LCD
monitor to a screen that is suitable for shooting when you look into the
viewfinder. The screen in the viewfinder is for Live View.
MENU button t
2 t [Display Rec. Data] t [For viewfinder]
Each time you press DISP on the control button, the screen changes as
follows.
Graphic Display
Recording
information display information off
(For viewfinder)
Recording
Digital level gauge
on
41
Recording information display (Graphic Display/Recording
information (For Live View))
The Graphic Display graphically shows the shutter speed and aperture
value and clearly illustrates how the exposure works.
Graphic Display
Recording information display
(For Live View)
A
Display
Indication
Image quality of still
images (143)
Display
Indication
•
(SLT-A55/A55V)/
(SLT-A33)
P A
Image size of movies
S M
100
Overheating warning
Memory card (20)
Remaining number of
recordable images (32)
Database file full (190)/
Database file error (190)
Image size of still images
(141)/Aspect ratio of still
of panoramic images
Camera shake warning
No audio recording of
movies (82)
42
Display
Indication
Display
Indication
GPS triangulating status
(138) (SLT-A55V only)
AF area (89)
Face Detection (93)
Smile Shutter (94)
Smile Detection
Sensitivity indicator (94)
B
Display
Indication
Spot metering area (105)
AF area (89)
Shutter speed indicator
E
Aperture indicator (72)
Display
Indication
ISO sensitivity (106)
Metering (105)
C
Display
Indication
+2.0
AWB
Flash compensation (103)
REC 0:12
Recording time of the
movie (m:s)
White balance (Auto,
Preset, Custom, Color
temperature, Color filter)
z
1/250
F3.5
Shutter speed (75)
Aperture (72)
D-Range Optimizer
Creative Style (110)
AE lock (100)
SteadyShot scale (57)
D
Display
Indication
Drive mode (116)
reduction (98)
Focus mode (88)
43
Recording information display (For viewfinder)
See pages in parentheses for details of operation.
In AUTO, AUTO+, or
Scene Selection mode
In Continuous Advance Priority AE/
P/A/S/M mode
A
Display
Indication
GPS triangulating status
(138) (SLT-A55V only)
Display
Indication
P A
•
(SLT-A55/A55V)/
(SLT-A33)
S M
100
B
Memory card (20)
Display
Indication
Remaining number of
recordable images (32)
reduction (98)
Image size of still images
(141)/Aspect ratio of still
images (143)
Drive mode (116)
Focus mode (88)
Image quality of still
images (143)
Image size of movies
Face Detection (93)
Smile Shutter (94)
No audio recording of
movies (82)
44
Display
AWB
Indication
AF area (89)
ISO sensitivity (106)
White balance (Auto,
Preset, Custom, Color
temperature, Color filter)
D-Range Optimizer
Creative Style (110)
Metering mode (105)
Exposure compensation
(101)/Metered Manual
Flash compensation (103)
C
Display
1/125
F2.8
Indication
Shutter speed (75)
Aperture (72)
Exposure (101)
AE lock (100)
SteadyShot (57)
+1.0
45
Selecting a function/setting
You can select a function for shooting or playback with the one of buttons,
such as the Fn (Function) button, or the MENU button.
When you start an operation, an operation
guide of control button functions will be
displayed at the bottom of the screen.
: Press v/V/b/B on the control
button to move the cursor.
z: Press the center button to execute the
selection.
In this Instruction Manual, the process of selecting a function with the
control button and the Fn button from the list displayed on the screen is
described as follows (we explain the process with the default icons.):
Example: Fn button t AWB (White Balance) t Select the
desired setting
The operation guide list
The operation guide also indicates operations other than the control button
operation. The indications of icons are as follows.
MENU button
Returns with MENU button
(Delete) button
(Zoom in) button
(Zoom out) button
(Playback) button
Control dial
Help guide
The Help Guide shows the information on a function selected with the Fn
button, MENU button, etc. You can also turn it off (page 151).
46
Selecting a function with the Fn (Function) button
This button is used for setting up or executing functions used frequently in
shooting.
1 Press the Fn button.
2 Select the desired item with v/V/
b/B on the control button, then
press the center z to execute.
The setup screen appears.
3 Following the operation guide,
select and execute the desired
function.
• For details on how to set up each item,
see the corresponding page.
Operation guide
To set up the camera directly from the recording information screen
Turn the control dial without pressing the
center z in step 2. You can set up the
camera directly from the recording
information screen.
47
The functions selected by the Fn (Function) button
preset settings to suit shooting conditions.
Panorama.
Drive Mode (116)
Flash Mode (96)
Sets the shooting mode to single-shot adv., continuous adv.,
self-timer, bracket shooting, etc.
Sets the flash mode to Autoflash, Fill-flash, Flash Off, etc.
the subject.
AF area (89)
Selects the area of focus.
focus and exposure.
Smile Shutter (94)
Camera shoots when a smile is detected.
Sets the sensitivity to light. The larger the number, the faster
the shutter speed.
Flash Compensation Adjusts the intensity of flash output. + direction increases
brightness of subject, and the - direction increases darkness.
48
The functions selected by the MENU button
You can set up the basic settings for the camera as a whole or execute
functions such as shooting, playback, or other operations.
Press the MENU button, select the desired page with b/B on the control
button, and select the desired item with v/V.
Recording menu
Image: Size (141)
Selects the size of still images.
Image: Aspect Ratio Selects the aspect ratio for still images.
Movie: File Format
Selects the movie file format.
Movie: Size (142)
Selects the size of the recorded movie frame.
Movie: Audio Rec.
Sets whether or not to record audio when shooting a
movie.
SteadyShot (57)
Sets SteadyShot.
49
Panorama: Size
Selects the size of panoramic images.
Panorama: Direction Sets the shooting direction for panoramic images.
3D Pan.: Image Size Selects the size of 3D-images.
3D Pan.: Direction
Sets the shooting direction for 3D-images.
Flash control (104)
AF Illuminator (98)
Color Space (111)
Sets the method for determining the intensity of flash
output.
Sets the AF illuminator, which sheds light on a dark
scene to aid focusing.
Changes the range of reproducible colors.
Long Exposure NR
Sets noise reduction processing for shots in which
shutter speed will be 1 second or longer.
High ISO NR (149)
Sets noise reduction processing for high-sensitivity
shooting.
50
Custom menu
Eye-Start AF (39)
Sets whether or not to use auto focus when you look
through viewfinder.
FINDER/LCD Setting Sets the method for switching between the viewfinder
and LCD monitor.
AEL button (150)
Sets the operation method of the AE lock button for
fixing exposure during shooting.
Focus Hold Button
Sets the function of the focus hold button of the lens.
Focus Magnifier
Sets whether or not to assign the
the functions used with the Focus Magnifier feature.
(Delete) button to
Red Eye Reduction
Reduces the red-eye phenomenon during flash use.
Release w/oLens
Sets whether shutter can open when lens is not
attached.
Grid Line (154)
Histogram (102)
Sets a grid line display to enable alignment to a
structural outline.
Sets whether or not to include the histogram display
when switching screen display.
Display Rec. Data
Selects the status of the recording information display
on the LCD monitor, either [For Live View] or [For
viewfinder].
Auto Review (154)
Displays the captured image after shooting. Sets auto
review.
Auto+ Cont. Advance Sets whether or not to shoot continuously in AUTO+
(62) mode.
Auto+ Image Extract. Sets whether or not to save all the images that were
(62) shot continuously in AUTO+ mode.
51
Playback menu
Delete (132)
Deletes images.
Still/Movie Select
Switches between the still image playback screen and
the movie playback screen.
Slide Show (125)
Image Index (125)
3D Viewing (135)
Shows a slide show.
Displays the image list.
Plays back 3D-images using a 3D-compatible TV
connected to the camera.
Protect (131)
Protects or cancels protection for an image.
Specifies or unspecifies the images for DPOF.
Specify Printing
Volume Settings
Sets the volume for movie playback.
Select Folder (121)
Select Date (123)
Changes the folder for images to play back.
Displays images from another date.
Playback Display
Sets how to play back an image recorded in portrait.
52
Memory Card Tool menu
Format (146)
Formats the memory card.
File Number (145)
Sets the method used to assign file numbers to still
images and movies.
Folder Name (145)
Sets the folder format for still images.
Select REC Folder
Changes the selected folder for storing still images.
New Folder (146)
Creates a new folder for storing still images and
movies.
Recover Image DB
Recovers the image database file for movies and
enables recording and playback.
Display Card Space Displays the remaining recording time of movies and
the recordable number of still images on the memory
card.
Clock setup menu
53
Setup menu
Viewfinder Bright.
Sets the brightness of the viewfinder.
GPS Settings (138)
(SLT-A55V only)
Sets the GPS functions.
Power Save (151)
Sets the interval after which power save mode
engages.
CTRL FOR HDMI
Operates the camera from a TV that support
“BRAVIA” Sync.
Language (152)
Selects the language.
Help Guide Display
Sets the display of the help guide for explaining
functions displayed during operation.
Upload Settings
Sets the upload function of the camera when using an
Eye-Fi card.
USB Connection
Sets the USB connection method.
focus is achieved or the self-timer is working.
Version (155)
Displays the camera software version.
Demo Mode (152)
Sets the demonstration playback of a movie to on or
off.
* Appears when an Eye-Fi card (sold separately) is inserted in the camera.
54
Shooting images
Adjusting the angle of the LCD monitor
You can adjust the angle of the LCD
monitor to meet various shooting
situations.
You can shoot from various shooting
positions.
Low position
High position
Adjust the LCD monitor to an easily
viewable angle.
• The LCD monitor tilts 180 degrees.
• The LCD monitor can be rotated
leftward 270 degrees from the position
in which the LCD monitor is facing
forward as illustrated.
• When the LCD monitor is not used, it is
recommended that you close it with the
screen side facing to the camera.
55
Shooting an image without camera shake
“Camera shake” refers to unwanted movement of the camera that occurs
after the shutter button has been pressed, resulting in a blurred image.
To reduce camera shake, follow the instructions below.
Correct posture
Stabilize your upper body and take a position that keeps the
camera from moving.
In LCD monitor mode
In viewfinder mode
Point 1
One hand holds the grip of the camera, and the other hand supports the lens.
Point 2
Take a secure stance with your feet shoulder-width apart.
56
Point 3
Lightly tuck your elbows against your body.
When shooting in a kneeling position, steady your upper body by placing
your elbow on your knee.
Camera shake warning indicator
Due to potential camera shake, the
(Camera shake warning) indicator
flashes. In this case, use a tripod or the
flash.
(Camera shake warning) indicator
Note
• The
(Camera shake warning) indicator is displayed only in the modes that
automatically set the shutter speed. This indicator is not displayed in M/S modes.
Using the SteadyShot function
The SteadyShot function can reduce the effect of camera shake by the
equivalent of approximately 2.5 to 4 Ev in shutter speed.
The SteadyShot function is set to [On] in the default setting.
The SteadyShot scale indicator
The
(SteadyShot scale) indicator
shows the camera shake status. Wait until
the scale becomes low, then start
shooting.
(SteadyShot scale) indicator
To deactivate the SteadyShot function
MENU button t
1 t [SteadyShot] t [Off]
57
Note
• The SteadyShot function may not work optimally when the power has just been
turned on, right after you point the camera towards a subject, or when the shutter
button has been pressed all the way down without stopping halfway.
Using a tripod
In the following cases, we recommend that you mount the camera on a
tripod.
• Shooting without a flash under dark conditions.
• Shooting with slow shutter speeds, which are typically used in night-time
shooting.
• Shooting a close subject, such as in macro shooting.
• Shooting with a telescopic lens.
Note
• When using a tripod, deactivate the SteadyShot function because there is a potential
for malfunction of the SteadyShot function.
58
Shooting with the automatic setting
Shooting with appropriate settings automatically
The “AUTO” mode allows you to easily shoot any subject under any
conditions because the camera makes appropriate judgments on the
situation to adjust the settings.
Select
when shooting in a location where the use of a flash is restricted.
1 Set the mode dial to
(Flash Off).
or
or
2 Adjust the LCD monitor to an easily viewable angle and hold
the camera.
3 Overlay the AF area on the
desired subject.
• If the
(Camera shake warning)
indicator flashes, carefully shoot the
subject, holding the camera steady, or
by using a tripod.
(Camera shake warning)
indicator
AF area
4 When using a zoom lens, turn the
zoom ring, then decide on your
shot.
Zoom ring
59
5 Press the shutter button halfway
down to focus.
When the focus is confirmed, z or
• Waiting until the
(SteadyShot
scale) indicator is low makes the
SteadyShot function more effective.
Focus indicator
(SteadyShot scale) indicator
6 Press the shutter button fully
down to shoot.
Note
• Since the camera turns on the automatic setting function, many features will be
unavailable, such as exposure compensation, ISO setting. If you want to adjust
various settings, set the mode dial to P, then shoot your subject.
60
Shooting with the settings that the camera adjusts
automatically
The camera recognizes and evaluates the shooting condition, and
appropriate settings are set automatically. The camera saves one
appropriate image by combining or separating images, as necessary.
1 Set the mode dial to
(Auto+).
Recognized scene mode mark
2 Point the camera towards the
subject.
When the camera recognizes and adjusts
for shooting conditions, the following
information is indicated: recognized
scene mode mark, appropriate shooting
function, the number of images to be
shot.
Shooting function
Number of images to be shot
3 Adjust the focus and shoot the subject.
The camera shoots with the automatically selected settings.
Scene recognized by the camera
(Night View)
(Hand-held Twilight)
(Portrait)
(Landscape)
(Backlight Portrait)
(Backlight)
(Tripod Night View)
(Night Portrait)
(Macro)
Shooting function
Slow Sync. (96)
Slow Shutter
61
To set the continuous shooting
MENU button t
2 t [Auto+ Cont. Advance] t Select the
desired setting
To select the storage method to be used for recorded images
In continuous shooting, you can select a storage method that allows the
camera either to store one appropriate image from among the continuously
shot images or store all the images.
MENU button t
2 t [Auto+ Image Extract.] t Select the
desired setting
Notes
• Even when you set [Auto+ Image Extract.] to [Off] with [Hand-held Twilight]
selected from recognized scene mode, one combined image is saved.
• The numbers of images that were not saved are skipped when the images are
extracted.
62
Shooting with a suitable setting for the
subject
Selecting an appropriate mode for the subject or the shooting conditions
allows you to shoot the image with a suitable setting for the subject.
When you turn the mode dial, the explanation of the selected mode and
methods of shooting are displayed on the screen (Help Guide Display).
Shooting with preset settings according to the scene
(Scene Selection)
This mode is suitable for
zShooting with preset settings
according to the scene
1 Set the mode dial to
(Scene Selection).
2 Press the center of the control button.
3 Select the desired mode with v/V, then press the center of the
control button.
• To change the scene, press the Fn button, then select another scene.
63
(Portrait)
Blurs away backgrounds and sharpens
the subject. Expresses skin tones softly.
• To blur the background more, set the
lens to the telephoto position.
• You can shoot a vivid image by
focusing on the eye that is closer to the lens.
• Use the lens hood (sold separately) to shoot backlit
subjects.
• Use the red-eye reduction function if the eyes of your
subject turn red from the flash (page 98).
(Sports Action)
Shoots a moving subject at a fast
shutter speed so that the subject looks
as if it is standing still. The camera
shoots images continuously while the
shutter button is pressed.
• Press and hold the shutter button halfway down until the
right moment.
(Macro)
Shoots close subjects such as flowers,
foods.
• You can shoot a closer subject using
a macro lens (sold separately).
• Set the flash mode to [Flash Off]
when you shoot a subject within 1 m (3.3 feet).
• When shooting in macro mode, the SteadyShot function
will not be fully effective. Use a tripod to achieve better
results.
• The shortest focal distance does not change.
(Landscape)
(Sunset)
Shoots the entire range of scenery in
sharp focus with vivid colors.
• To accentuate the openness of the
scenery, set the lens to wide angle.
Shoots the red of the sunrise or sunset
beautifully.
(Night View)
Shoots night scenes at a distance
without losing the dark atmosphere of
the surroundings.
• The shutter speed is slower, so using
a tripod is recommended.
• The picture may not be taken properly when shooting a
wholly dark night scene.
64
(Hand-held
Twilight)
Shoots night scenes with less noise and
blur without using a tripod. A burst of
shots are taken, and image processing
is applied to reduce subject blur,
camera shake, and noise.
• Reducing blur is less effective even in [Hand-held
Twilight] when shooting:
– Subjects with erratic movement
– Subjects are too close to the camera
– Subjects with a repeating pattern such as tiles, and
subjects with little contrast such as sky, sandy beach, or
lawn
– Subjects with constant change such as waves or water
falls
• In the case of [Hand-held Twilight], block noise may occur
when using a light source that flickers, such as fluorescent
lighting.
(Night Portrait)
Shoots portraits in night scenes.
• The shutter speed is slower, so using
a tripod is recommended.
Shooting technique
• When you want finer images, set the mode dial to P, A, S, or M and use
exposure, ISO, etc.
Notes
• Since the camera judges the settings automatically, many features will be
unavailable, such as exposure compensation, ISO setting.
• The flash is set to [Autoflash] or [Flash Off] for each Scene Selection mode. You can
change these settings (page 96).
65
Shooting panoramic images (Sweep Shooting)
This mode is suitable for
zShooting expansive scenery, or high-rise buildings with dynamic composition.
1 Set the mode dial to
(Sweep Shooting).
2 Press the center of the control button.
3 Select [Sweep Panorama] with v/V, then press the center of
the control button.
• To select [3D Sweep Panorama], press the Fn button, then select it.
4 Point the camera at the edge of
the subject, then press the shutter
button halfway down to adjust the
focus.
This part will not be taken
5 Press the shutter button fully down.
66
6 Pan or tilt the camera to the end,
following the guidance on the
screen.
Guidance bar
Notes
• If you cannot pan or tilt the camera across the entire subject within the given time, a
gray area occurs in the composed image. If this happens, move the camera fast to
record a full panoramic image.
• Since several images are stitched together, the stitched part will not be recorded
smoothly. While shooting, do not tilt the camera back and forth, or right and left
when you swing the camera straight ahead.
• Under low light conditions, panoramic images may be blurred or not be recorded.
• Under lights that flicker such as fluorescent light, the brightness or color of the
combined image is not always the same.
• When the whole angle of panoramic shooting and the angle in which you fixed the
focus and exposure with AE/AF lock are extremely different in brightness, color and
focus, the shooting will not be successful. If this happens, change the lock angle and
shoot again.
• [Sweep Panorama] is not suitable when shooting:
– Subjects are moving.
– Subjects are too close to the camera.
– Subjects with a repeating pattern such as tiles, and subjects with little contrast such
as sky, sandy beach, or lawn.
– Subjects with constant change such as waves or water falls.
– Subjects with the sun or electric lights, etc. that are much brighter than
surroundings.
• [Sweep Panorama] recording may be discontinued in the following situations:
– You pan or tilt the camera too fast or too slow.
– There is too much camera shake.
• The camera continues shooting during [Sweep Panorama] recording, and the shutter
keeps clicking until the end of the shooting.
67
Tips for shooting a panoramic image
Pan or tilt the camera in an arc with a
constant velocity and in the same
Vertical
direction
Horizontal direction
direction as the indication on the screen.
[Sweep Panorama] is better suited for
still subjects, rather than moving ones.
Radius as short as
possible
• In Sweep Panorama, it is recommended that you use a wide-angle lens.
• When you use a lens that has a long focal length, pan or tilt the camera
more slowly than when you use a wide-angle lens.
• Determine the scene and press the shutter button halfway, so that you can
lock the focus, exposure, and white balance.
• If a section with greatly varied shapes or scenery is concentrated along a
screen edge, the image composition may fail. In such case, adjust the
frame composition so that the section is in the center of the image, then
shoot again.
• You can select the image size: MENU button t
2 t [Panorama:
Size].
To create 3D-images
Set the mode dial to
(Sweep Shooting), select [3D Sweep Panorama],
and shoot the image. Using the same operation as that for Sweep Panorama,
the camera records multiple images and combines them to create a 3D-
image. You can view these 3D images using a 3D-compatible TV. For
details on 3D-shooting, see page 198.
To set the pan or tilt direction
You can set the direction in which to pan or tilt the camera.
MENU button t
2 t [Panorama: Direction] or [3D Pan.:
Direction] t Select the desired setting
68
Shooting continuously at high speed (Continuous
Advance Priority AE)
This mode is suitable for
zShooting a fast-moving subject
continuously to capture a moment.
zShooting a child’s expressions,
changing continuously from moment
to moment.
1 Set the mode dial to
(Cont. Priority AE).
(SLT-A55/A55V) or
(SLT-A33)
2 Adjust the focus and shoot the subjects.
• The camera continues to shoot while the shutter button is pressed fully
down.
• The camera records the images continuously at a maximum of about 10
images per second (SLT-A55/A55V) or at a maximum of about 7 images
per second (SLT-A33).
Shooting technique
• When the autofocus mode is set to [Continuous AF], the focus and the
exposure continue to be adjusted during shooting. When it is set to
[Single-shot AF], you can adjust the aperture using the control dial. The
focus is fixed at the first image.
Notes
• The Face Detection function is turned off.
• When [Auto HDR] is selected, the DRO process is performed temporarily according
to the DRO setting.
• Our measurement conditions. The speed of continuous shooting is slower,
depending on shooting conditions.
69
Shooting an image the way you want it
(Exposure mode)
With an Interchangeable Lens Digital Camera, you can adjust the shutter
speed (how long the shutter is open) and aperture (the range that is in focus:
depth of field) to enjoy a variety of photographic expressions.
Adjusting the shutter speed and aperture not only creates the photographic
effects of movement and focus, but also determines the brightness of the
image by controlling the amount of exposure (the amount of light the
camera takes in), which is the most important factor in photo shooting.
Changing the brightness of the picture by the amount of exposure
Amount of
exposure
low
high
When using a faster shutter speed, the camera opens the shutter for a
shorter time. This means less time for the camera to take in light, resulting
in a darker picture. To take a brighter picture, you can open the aperture
(the hole through which the light passes) to some extent in order to adjust
the amount of light the camera takes in at one time.
The brightness of the picture adjusted by the shutter speed and aperture is
called “exposure.”
This section will show you how to adjust the exposure and enjoy various
photo expressions by the use of movement, focus, and light.
70
Shooting by controlling the blur of the background
(Aperture priority)
This mode is suitable for
zPutting the subject in sharp focus
and blur everything in front of and
beyond the subject. Opening the
aperture narrows the range that is in
focus. (Depth of field becomes
shallower.)
zShooting the depth of the scenery.
Narrowing down the aperture widens
the range that is in focus. (Depth of
field becomes deeper.)
1 Set the mode dial to A.
72
2 Select the aperture value (F-
number) with the control dial.
• Smaller F-number: The foreground and
background of the subject are blurred.
Larger F-number: The subject and its
foreground and background are all in
focus.
• You cannot check the blurring of an
image on the LCD monitor or in the
viewfinder. Check the recorded image
and adjust the aperture.
Aperture (F-number)
3 Adjust the focus and shoot the
subject.
The shutter speed is automatically
adjusted to obtain correct exposure.
• When the camera judges that the proper
exposure is not obtained with the
selected aperture value, the shutter
speed flashes. In such cases, adjust the
aperture again.
Shutter speed
Shooting techniques
• The shutter speed may become slower depending on the aperture value.
When the shutter speed is slower, use a tripod.
• To blur the background more, use a telephoto lens or a lens that is
equipped with a smaller aperture value (bright lens).
• You can check the approximate blurring of the image before recording
using the preview button.
Note
• Press the button when you shoot with the flash. However, the flash range differs
according to the aperture value. When you shoot with the flash, check the flash range
73
To check blurring of the background (Preview button)
The LCD monitor and the viewfinder
shows an image captured with the widest
aperture. The change in aperture affects
the sharpness of the subject image,
creating a discrepancy between the
sharpness of the image before shooting
and that of the actual image.
Preview button
While you are pressing the preview
button, you can see the image with the
aperture used in the actual shot so that
you can check the approximate sharpness
of the subject before shooting.
• Press the preview button after you adjust the focus.
• You can adjust the aperture in preview mode.
74
Shooting a moving subject with various expressions
(Shutter speed priority)
This mode is suitable for
zShooting a moving subject at a
moment in time. Use a faster shutter
speed to crisply shoot an instant of
the movement.
zTracing the movement to express the
dynamism and flow. Use a slower
shutter speed to shoot a trailing
image of the moving subject.
1 Set the mode dial to S.
75
2 Select the shutter speed with the
control dial.
Shutter speed
3 Adjust the focus and shoot the
subject.
The aperture is automatically adjusted to
obtain correct exposure.
• When the camera judges that the proper
exposure is not obtained with the
selected shutter speed, the aperture
value flashes. In such cases, adjust the
shutter speed again.
Aperture (F-number)
Shooting techniques
• When the shutter speed is slower, use a tripod.
• When shooting an indoor sport, select a higher ISO sensitivity.
Notes
• The
(Camera shake warning) indicator is not indicated in shutter speed priority
mode.
• The higher the ISO sensitivity, the more conspicuous the noise.
• When the shutter speed is one second or more, noise reduction (Long Exposure NR)
will be done after shooting. You cannot do any further shooting during the reduction.
• Press the button when you shoot with the flash. However, when using the flash, if
you close the aperture (a larger F-number) by making the shutter speed slower, the
light of the flash will not reach distant subjects.
76
Shooting with the exposure adjusted manually (Manual
exposure)
This mode is suitable for
zShooting with the desired exposure
setting by adjusting both the shutter
speed and aperture.
1 Set the mode dial to M.
2 Rotate the control dial to adjust
the shutter speed, and while
pressing the
button, rotate the
control dial to adjust the aperture.
button
Aperture (F-number)
Shutter speed
77
3 Shoot the image after the
exposure is set.
• Check the exposure value on the EV
scale (Metered Manual*).
Toward +: Images become brighter.
Toward –: Images become darker.
The b B arrow appears if the set
exposure is beyond the range of the EV
scale. The arrow starts flashing if the
difference becomes greater.
Standard value
* When the camera is in M mode, it will
show an under or over compensation
value based on the correct exposure
using the index on the exposure
compensation indicator.
Notes
• The
(Camera shake warning) indicator is not indicated in manual exposure
mode.
• When the mode dial is set to M, the ISO setting [AUTO] is set to [100]. In M mode,
the ISO setting [AUTO] is not available. Set the ISO sensitivity as necessary
• Press the button when you shoot with the flash. However, the flash range differs
according to the aperture value. When you shoot with the flash, check the flash range
Manual shift
You can change the shutter speed and aperture value combination without
changing the exposure you set.
Rotate the control dial while pressing the
AEL button to select the shutter speed
and aperture value combination.
AEL button
78
Shooting trails with long exposure (BULB)
This mode is suitable for
zShooting trails of light, such as
fireworks.
zShooting trails of stars.
1 Set the mode dial to M.
2 Rotate the control dial to the left
until [BULB] is indicated.
BULB
3 While pressing the
button,
rotate the control dial to adjust
the aperture (F-number).
button
79
4 Press the shutter button halfway down to adjust the focus.
5 Press and hold the shutter button for the duration of the
shooting.
As long as the shutter button is pressed, the shutter remains open.
Shooting techniques
• Use a tripod.
• Set the focus to infinity in manual focus mode when shooting fireworks,
etc. When the infinity position of the lens is not known, first adjust the
focus on fireworks that is set off in the same general area, then shoot
them.
• Use the Wireless Remote Commander (sold separately) (page 120).
Pressing the SHUTTER button on the Wireless Remote Commander
triggers BULB shooting and pressing it again stops BULB shooting. You
do not need to press and hold the SHUTTER button on the Wireless
Remote Commander.
• If you use a Remote Commander that is equipped with a shutter button
lock function (sold separately), you can leave the shutter open using the
Remote Commander.
Notes
• When using a tripod, turn off the SteadyShot function (page 57).
• The longer the exposure time, the more conspicuous the noise on the image.
• After shooting, noise reduction (Long Exposure NR) will be done for the same
amount of time that the shutter was open. You cannot do any further shooting during
the reduction.
• When the Smile Shutter or Auto HDR function is activated, you cannot set the
shutter speed to [BULB].
• If the Smile Shutter or Auto HDR function is used with the shutter speed set to
[BULB], the shutter speed is temporarily set to 30 seconds.
• It is recommended that you start BULB shooting after the temperature of the camera
drops to prevent the quality of the image from deteriorating.
80
Recording movies
MOVIE button
1 Press the MOVIE button to start
recording.
• Movie recording can be started from
any exposure mode.
• The shutter speed and aperture are
adjusted automatically.
• The camera continues to adjust the
focus when it is in autofocus mode.
2 Press the MOVIE button again to stop recording.
Shooting techniques
• The following settings that were set during still image shooting are used
without change.
– White Balance
– Creative Style
– Exposure compensation
– AF area
– Metering mode
• Exposure compensation can be used during movie recording.
• Start recording after you adjust the focus.
• When [AF area] is set to [Local], you can change the AF area during
shooting.
Notes
• The angle of view of movies is narrower than that of still images. After you press the
MOVIE button, the camera shows the actual range to be recorded (SLT-A33 only).
• The Face Detection function cannot be used.
• When [Display Rec. Data] is set to [For viewfinder], the LCD monitor is switched to
the recording information display at the moment movie recording starts.
• Do not shoot a strong light source, such as the sun. The internal mechanism of the
camera may be damaged.
• When you import AVCHD movies to a computer, use “PMB” (page 165).
81
• When you continue to shoot for a long time, the temperature of the camera rises and
the image quality may deteriorate.
• When the
mark is indicated, the temperature of the camera is too high. Turn the
camera off and wait until the temperature of the camera drops. If you continue to
shoot, the camera is turned off automatically.
To change the movie file format
MENU button t
1 t [Movie: File Format] t Select the
desired format
AVCHD
This file format is suitable for viewing smooth video images
on a high-definition TV.
Movies shot with this camera are recorded in AVCHD
format, approximately 60 fields/sec (1080 60i-compatible
devices) or 50 fields/sec (1080 50i-compatible devices), in
interlace mode, with Dolby Digital audio, AVCHD format.
• To check if your camera is a 1080 60i-compatible device or
1080 50i-compatible device, check for the following marks
on the bottom of the camera.
1080 60i-compatible device: 60i
1080 50i-compatible device: 50i
MP4
This file format is suitable for WEB uploads, e-mail
attachments or playing back on computers.
Movies shot with this camera are recorded in MPEG-4
format at approximately 30 frames/sec (1080 60i-compatible
devices) or approximately 25 frames/sec (1080 50i-
compatible devices), in progressive mode, with AAC audio,
mp4 format.
Audio recording
When you record movies, the operating noise of the camera or lens may be
recorded. You can reduce the noise of the camera by using a tripod, and
setting the SteadyShot function to off.
You can also record movies without audio.
MENU button t
1 t [Movie: Audio Rec.] t [Off]
82
To change the size
MENU button t
1 t [Movie: Size] t Select the desired
size
For details, see page 142.
Available recording time for a movie
The table below shows the approximate total recording times using a
memory card formatted with this camera.
“Memory Stick PRO Duo”
SLT-A55/A55V
(Units: hour : minute : second)
Capacity
File
2GB
4GB
8GB
16GB
32GB
format/
Size
AVCHD 1920 ×
1080
0:14:00
0:28:30
0:58:10
1:58:50
3:55:20
MP4 1440 × 1080
MP4 VGA
0:20:40
1:15:10
0:41:40
2:31:10
1:24:40
5:06:20
2:52:30
5:41:00
10:23:50
20:33:00
SLT-A33
(Units: hour : minute : second)
Capacity
File
2GB
4GB
8GB
16GB
32GB
format/
Size
AVCHD 1920 ×
1080
0:14:00
0:28:30
0:58:10
1:58:50
3:55:20
MP4 1440 × 1080
MP4 VGA
0:20:40
1:15:10
0:41:40
2:31:10
1:24:40
5:06:20
2:52:30
5:41:00
10:23:50
20:33:00
Notes
• The values shown are not the continuous recording time.
• Recording time may depend on shooting conditions and the memory card used.
• When is indicated, stop recording the movie. The temperature inside the camera
has increased to an unacceptable level.
• For details on movie playback, see page 122.
83
Notes on continuous movie recording
• Each continuous recording time value indicated is depending on the temperature or
status of the camera.
• The recording time is longer when you disable the SteadyShot function that calls for
using a tripod or a similar device.
• Each continuous recording time limit indicated for a movie is available for about
nine minutes (SLT-A55/A55V) or for about 11 minutes (SLT-A33) at a room
temperature of 20°C (68°F). When you disable the SteadyShot function, it is
available for about 29 minutes (SLT-A55/A55V/A33).
• If
is indicated or the camera is turned off automatically since the temperature
inside the camera is too high, you can record movies again after turning off the
camera for several minutes.
• The maximum size of a movie file is about 2 GB. When the file size is about 2 GB,
the recording stops automatically when the file format is MP4, and a new movie file
is created automatically when the file format is AVCHD.
• The maximum continuous recording time is 29 minutes.
84
Using the shooting function
Selecting the focus method
There are two methods for adjusting the focus: autofocus and manual focus.
Depending on the lens, the method for switching between the auto focus
and manual focus is different.
The switch to be To switch to auto
used focus
To switch to manual
focus
The type of lens
The lens is
equipped with a
focus mode switch switch on the
camera to AF.)
Lens (Always set Set the focus mode Set the focus mode
the focus mode switch on the lens to switch on the lens to
AF. MF.
The lens is not
equipped with a
focus mode switch
Camera
Set the focus mode Set the focus mode
switch on the camera switch on the camera
to AF.
to MF.
Using autofocus
1 Set the focus mode switch on the
camera to AF.
2 When the lens is equipped with
the focus mode switch, set it to
AF.
85
3 Press the shutter button halfway
down to check the focus and shoot
the image.
• When the focus is confirmed, the focus
indicator changes to z or
(below).
• The AF area where the focus has been
confirmed turns green.
AF area
Focus indicator
Shooting technique
Focus indicator
Focus indicator
Status
z lit
Focus locked. Ready to shoot.
lit
Focus is confirmed. Focal point moves following a moving
subject. Ready to shoot.
lit
Still focusing. You cannot release the shutter.
Cannot focus. The shutter is locked.
z flashing
Subjects that may require special focusing
Using the autofocus, it is hard to focus on the following subjects. In such
• A subject that is low in contrast, such as blue sky or a white wall.
• Two subjects at different distances overlapping in the AF area.
• A subject that is composed of repeating patterns, such as the facade of a
building.
• A subject that is very bright or glittering, such as the sun, the body of an
automobile, or the surface of water.
• Ambient light is not sufficient.
86
To measure the exact distance to the subject
The mark located on the top of the
camera shows the location of the image
sensor*. When you measure the exact
distance between the camera and the
subject, refer to the position of the
horizontal line.
* The image sensor is the part of the
camera that acts as the film.
Note
• If the subject is closer than the minimum shooting distance of the attached lens, the
focus cannot be confirmed. Make sure you put enough distance between the subject
and the camera.
Shooting with your desired composition (Focus-lock)
1 Place the subject within the AF
area and press the shutter button
halfway down.
The focus and exposure are fixed.
2 Keep the shutter button halfway
down, and put the subject back in
the original position to re-
compose the shot.
3 Press the shutter button fully down to take the picture.
87
Selecting the focus method to suit the movement of the
subject (Autofocus Mode)
Fn button t
(Autofocus Mode) t Select the desired setting
(Single-shot
AF)
The camera focuses and the focus is locked when you press
the shutter button halfway down.
(Automatic AF) The [Autofocus Mode] is switched between Single-shot AF
and Continuous AF according to the movement of the
subject.
When you press and hold the shutter button halfway down, if
the subject is motionless, the focus is locked and if the
subject is in motion, the camera continues to focus.
(Continuous
The camera continues to focus while the shutter button is
pressed and held halfway down.
AF)
• The audio signals will not sound when the subject is in
focus.
• Focus-lock cannot be used.
Shooting techniques
• Use [Single-shot AF] when the subject is motionless.
• Use [Continuous AF] when the subject is in motion.
Notes
• [Automatic AF] is selected when the exposure mode is set to AUTO, AUTO+ or one
of the following Scene Selection modes: [Portrait], [Landscape], [Sunset], [Night
View], [Night Portrait], or [Hand-held Twilight].
[Single-shot AF] is selected when the exposure mode is set to [Macro] in Scene
Selection.
[Continuous AF] is selected when the exposure mode is set to [Sports Action] in
Scene Selection.
• [Continuous AF] is selected when the Smile Shutter function is used.
88
Selecting the focus area (AF area)
Select the desired AF area to suit the
shooting conditions or your preference.
The AF area where the focus has been
confirmed turns green and the other AF
areas disappear.
AF area
Fn button t
(Wide)
(AF area) t Select the desired setting
The camera determines which of the 15 AF areas is used in
focusing.
(Spot)
The camera uses the AF area located in the center area
exclusively.
(Local)
Choose the area for which you want to activate the focus
from among 15 AF areas with the control button. Press the
AF button to display the setup screen and select the desired
area.
Notes
• When the exposure mode is set to AUTO, AUTO+, Sweep Panorama or Scene
Selection, or the Smile Shutter is activated, [AF area] is fixed to [Wide] and you
cannot select the other settings.
• The AF area may not be illuminated during continuous shooting or when the shutter
button is pressed all the way down without pause.
89
Adjusting the focus manually (Manual focus)
When it is difficult to get the proper focus in autofocus mode, you can
adjust the focus manually.
1 Set the focus mode switch on the
lens to MF.
2 When the lens is not equipped
with the focus mode switch, set
the focus mode switch on the
camera to MF.
3 Rotate the focusing ring of the
lens to achieve a sharp focus.
Focusing
ring
Notes
• In the case of a subject that can be focused in autofocus mode, the z indicator lights
up when the focus is confirmed. When the Wide AF area is used, the center area is
used, and when the Local AF area is used, the area that is selected with the control
button is used.
• When using a tele converter (sold separately), etc., rotation of the focusing ring may
not be smooth.
• The correct focus in the viewfinder is not achieved if the diopter is not adjusted
properly in viewfinder mode (page 29).
90
Checking the focus by enlarging the image
You can check the focus by enlarging the image before shooting.
1 MENU button t
1 t [Focus Magnifier] t [On]
2 Press the Focus Magnifier button.
Focus Magnifier button
3 Press the Focus Magnifier button
again to enlarge the image and
select the portion you want to
enlarge with v/V/b/B on the
control button.
• Each time you press the Focus
Magnifier button, the zoom scaling
changes as follows: Full display t
Approx. ×7.5 t Approx. ×15 (SLT-
A55/A55V)/Full display t Approx.
×7 t Approx. ×14 (SLT-A33)
4 Confirm and adjust the focus.
• Rotate the focusing ring to adjust the focus in manual focus mode.
• If you press the AF button in autofocus mode, the Focus Magnifier function
is canceled and the autofocus is activated.
• The Focus Magnifier function is canceled if you press the shutter button
halfway down.
91
5 Press the shutter button fully down to shoot the image.
• You can record images when an image is enlarged, however the recorded
image is for full display.
• The Focus Magnifier function will be released after shooting.
92
Detecting faces
Using the Face Detection function
The camera detects faces, adjusts the focus, exposure, performs image
processing, and adjusts flash settings. The Face Detection function is set to
[On] in the default setting.
The Face Detection frame
When the camera detects faces, white
Face Detection frames appear. When the
camera judges that autofocus is possible,
the Face Detection frames turn orange.
When you press the shutter button
halfway down, the Face Detection frames
Face Detection frames
(white)
turn green.
• If a face is not positioned inside the AF
area available when you press the
shutter button halfway down, the AF
area that is used for focusing turns
green.
Face Detection frames (orange)
• When the camera detects multiple
faces, the camera automatically selects
a priority face and the single Face
Detection frame turns orange.
To deactivate the Face Detection function
Fn button t
(Face Detection) t [Off]
Shooting technique
• Compose to overlay the Face Detection frame and the AF area.
Notes
• When the exposure mode is Sweep Panorama, Continuous Advance Priority AE, or
during movie recording, the Face Detection function cannot be used.
93
• Up to eight faces can be detected.
• The camera may not detect any faces, or may detect some other object, depending on
the shooting conditions.
Capturing smiling faces (Smile Shutter)
When the camera detects a smile, the shutter is released automatically.
1 Fn button t
(Smile Shutter) t [On] t Select the
desired Smile Detection Sensitivity mode
• When the Smile Shutter is activated, the Smile Detection Sensitivity
indicator appears on the screen.
2 Wait detecting a smile.
The camera detects a smile and the focus
is confirmed. When the smile level
exceeds the b point on the indicator, the
camera records images automatically.
• When the camera detects faces, orange
Face Detection frames appear around
the faces. The Face Detection frames
turn green when these subjects come
into focus.
Face Detection frame
Smile Detection Sensitivity indicator
• The smile level of the face surrounded
by the double Face Detection frame is
indicated on the Smile Detection
Sensitivity indicator.
3 To stop shooting, Fn button t
(Smile Shutter) t [Off]
Smile Detection Sensitivity
You can set the sensitivity of the Smile Shutter function for detecting
smiles to one of the following three options: (Slight Smile),
(Normal Smile), and (Big Smile).
94
Shooting techniques
• To focus on the smile, overlay the Face Detection frame and AF area.
• Do not cover the eyes with bangs, etc. Keep the eyes narrowed.
• Do not obscure the face with a hat, a mask, sunglasses, etc.
• Try to orient the face in front of the camera and keep it as level as
possible.
• Hold a clear smile with an open mouth. The smile is easier to detect when
the teeth are showing.
• If you press the shutter button while the Smile Shutter function is
activated, the camera shoots the image, and then returns to Smile Shutter.
Notes
• When the exposure mode is set to Sweep Panorama or Continuous Advance Priority
AE, the Smile Shutter function cannot be used.
• The drive mode is automatically set to [Single-shot Adv.].
• The AF illuminator does not work with the Smile Shutter function.
• If the camera does not detect a smile, change the settings for Smile Detection
Sensitivity.
• Smiles may not be detected correctly, depending on the shooting conditions.
95
Using the flash
In a dark location, using the flash allows you to shoot the subject brightly,
and it also helps to prevent camera shake. When shooting into the sun, you
can use the flash to shoot a bright image of the backlit subject.
1 Fn button t (Flash Mode) t Select the desired setting
button
2 Press the button.
The flash pops up.
• In AUTO, AUTO+ or Scene Selection
mode, the flash automatically pops up
if the amount of light is insufficient or
the subject is backlit. The built-in flash
does not pop up even if you press the
button.
3 After the flash has finished
charging, shoot the subject.
z Flashing: The flash is being charged.
When the indicator flashes, you cannot
release the shutter.
z Lit: The flash has been charged and is
ready to fire.
z (Flash charging) indicator
• When you press the shutter button
halfway down under dark lighting in
autofocus mode, the flash may be fired
to help focus on a subject (AF
Illuminator).
• z is indicated only in the recording
information display (For Live View)
mode.
96
(Flash Off)
(Autoflash)
(Fill-flash)
(Slow Sync.)
Does not fire even the built-in flash pops up.
Fires if it is dark or against light.
Fires every time you trigger the shutter.
Fires every time you trigger the shutter. Slow sync shooting
allows you to shoot a clear image of both the subject and the
background by slowing the shutter speed.
(Rear Sync.)
(Wireless)
Fires right before the exposure is completed everytime you
trigger the shutter.
Fires an external flash (sold separately) that is off the camera
and away from it (Wireless flash shooting).
Shooting techniques
• The lens hood (sold separately) may block the light of the flash. Remove
the lens hood when using the flash.
• When using the flash, shoot the subject at a distance of 1 m (3.3 feet) or
greater.
• When shooting indoors or shooting nightscapes, you can use slow sync to
shoot a brighter image of people and backgrounds.
• You can use rear sync to shoot a natural image of the trail of a moving
subject such as a moving bicycle or a walking person.
• When using the HVL-F58AM/HVL-F42AM Flash (sold separately), you
can shoot with the High-speed sync feature at any shutter speed. For
details, refer to the operating instructions supplied with the flash.
Notes
• Do not hold the camera by grabbing the flash emitter.
• Shooting conditions required to prevent shadows from appearing on an image vary,
depending on the lens.
• When the exposure mode is set to AUTO, AUTO+, or Scene Selection, the [Slow
Sync.], [Rear Sync.], and [Wireless] items cannot be selected.
• When the exposure mode is set to P, A, S, M, the [Flash Off] or [Autoflash] items
cannot be selected. If you do not want to use the flash, push the flash down.
• If you use the flash with a stereo microphone or similar device attached to the Auto-
lock Accessory shoe, the flash may not pop up to the correct position and recorded
images may have a shadow on their corners. Remove any device from the Auto-lock
Accessory shoe.
97
The flash range
The range of the built-in flash depends on the ISO sensitivity and aperture
value. Refer to the following table.
Aperture
F2.8
1 – 3.6 m (3.3 – 12 1 – 2.5 m (3.3 – 8.2 1 – 1.8 m (3.3 – 5.9
feet) feet) feet)
1 – 5.1 m (3.3 – 17 1 – 3.5 m (3.3 – 12 1 – 2.5 m (3.3 – 8.3
F4.0
F5.6
ISO
setting
100
200
400
800
feet)
feet)
feet)
1.4 – 7.1 m (4.7 – 23 1 – 5 m (3.3 – 16
1 – 3.6 m (3.3 – 12
feet)
feet)
feet)
2 – 10 m (6.6 – 33
feet)
1.4 – 7.1 m (4.6 – 23 1 – 5.1 m (3.3 – 17
feet) feet)
The AF illuminator
• AF illuminator does not operate when [Autofocus Mode] is set to
(Continuous AF) or the subject is moving in (Automatic AF).
or indicator lights.)
(The
• The AF illuminator may not operate with focal lengths of 300 mm or longer.
• When an external flash (sold separately) that is equipped with an AF
illuminator is attached, the AF illuminator of the external flash is used.
• AF illuminator does not operate when [Smile Shutter] is set to [On].
To deactivate the AF illuminator
MENU button t
2 t [AF Illuminator] t [Off]
To use the red-eye reduction
The red-eye reduction reduces the red-eye phenomenon by providing pre-
flash (low-flash light) a few times before shooting when using the flash.
MENU button t
1 t [Red Eye Reduction] t [On]
98
Performing wireless flash shooting
With a flash that has a wireless shooting function (sold separately), you can
shoot with the flash without a cord, even when the flash is not attached to
the camera. By changing the position of the flash, you can shoot an image
with a three dimensional feel by highlighting the contrast of light and
shadow on the subject.
For the actual steps of shooting, refer to the operating instructions of the
flash.
1 Attach the wireless flash to the Auto-lock Accessory shoe and
turn both the camera and the flash on.
2 Fn button t (Flash Mode) t (Wireless)
3 Remove the wireless flash from the Auto-lock Accessory shoe
and pop up the built-in flash.
• If you perform a test fire of the flash, press the AEL button.
Notes
• The camera cannot carry out the wireless lighting ratio control.
• Turn off the wireless flash mode after wireless flash shooting. If the built-in flash is
used while the wireless flash mode is still active, inaccurate flash exposures will
result.
• Change the channel of the external flash when another photographer is using a
wireless flash nearby and his/her built-in flash light causes your external flash to fire.
To change the channel of the external flash, refer to the operating instructions
supplied with it.
Setup of the AEL button
When using a wireless flash, it is recommended that you set [AEL button]
to [AEL hold] in the
Custom menu (page 150).
99
Adjusting the brightness of the image
(Exposure, Flash compensation,
Metering)
Shooting with fixed brightness (AE Lock)
When shooting into the sun or by a window, the exposure may not be
appropriate for the subject because of the big difference in lighting between
the subject and the background. In such cases, use the light meter where the
subject is bright enough and lock the exposure before shooting. To reduce
the brightness of the subject, point the camera forwards a spot that is
brighter than the subject and use the light meter to lock the exposure of the
entire image. To make the subject brighter, point the camera forwards a
spot that is darker than the subject and use the light meter to lock the
exposure of the entire image.
This section describes how to shoot a brighter image of the subject using
the (Spot).
The spot where you
lock the exposure.
1 Fn button t (Metering Mode) t (Spot)
2 Adjust the focus on the portion you want to lock the exposure.
The exposure is set when the focus is achieved.
100
AEL button
3 Press the AEL button to lock the
exposure.
(AE lock mark) appears.
4 While pressing the AEL button, focus on the subject, and shoot
the subject.
• If you continue to shoot with the same exposure value, press and hold the
AEL button after the shooting. The setting is canceled when the button is
released.
Using brightness compensation for the entire image
(Exposure compensation)
Except for exposure mode M, the exposure is automatically selected
(Automatic exposure).
Based on the exposure acquired by the automatic exposure, you can
perform exposure compensation by shifting the exposure to either the +
side or the – side, depending on your preference. You can make the entire
image brighter by shifting to the + side. The entire image becomes darker
when you shift it to the – side.
Adjust in the –
direction
Base exposure
Adjust in the +
direction
101
button
1 Press the
button.
2 Adjust the exposure with the
control dial.
Toward + (over): Brightens an image.
Toward – (under): Darkens an image.
Standard exposure
3 Adjust the focus and shoot the subject.
Shooting techniques
• Adjust the compensation level by checking the recorded image.
• Using bracket shooting, you can shoot multiple images with the exposure
shifted to the plus or minus sides (page 118).
Note
• This item cannot be set when the exposure mode is set to AUTO, AUTO+, or Scene
Selection.
To shoot while checking the screen using the histogram
The histogram displays the luminance
distribution that shows how many pixels
of a particular brightness exist in the
picture.
Dark
Light
102
MENU button t
2 t [Histogram] t [On]
• Instead of the Graphic Display, the histogram is displayed after you press
DISP on the control button several times.
The exposure compensation will change
the histogram accordingly. The right
illustration is an example.
Shooting with the exposure
compensation on the positive side
brightens the whole picture, making the
entire histogram shift to the bright side
(right side). If the exposure compensation
is applied on the negative side, the
histogram will shift to the other side.
Both ends of the histogram show a high-
key or low-key portion. It is impossible to
restore these area with a computer later.
Adjust the exposure if necessary and
shoot again.
Notes
• The histogram does not indicate the final recorded image. It indicates the condition
of the image just monitored on the screen. The histogram will differ based on
aperture setting, etc.
• The histogram differs between shooting and playback in the following situations:
– When firing the flash.
– When the subject has low intensity, such as night scenery.
Adjusting the amount of flash light (Flash Compensation)
When shooting with the flash, you can adjust the amount of flash light
alone, without changing the exposure compensation. You can only change
the exposure of a main subject which is within the flash range.
103
Fn button t (Flash Compensation) t Select the desired
setting
Toward +: Makes the flash level higher.
Toward –: Makes the flash level lower.
Notes
• This item cannot be set when the exposure mode is set to AUTO, AUTO+, Sweep
Panorama, or Scene Selection.
• The higher flash effect may not be visible due to the limited amount of flash light, if
the subject is outside the maximum range of the flash. If the subject is very close, the
lower flash effect may not be visible.
Exposure compensation and flash compensation
Exposure compensation changes the shutter speed, aperture, and ISO sensitivity (when
[AUTO] is selected) to perform the compensation. If the flash is used, the amount of
flash light is also changed.
However, flash compensation only changes the amount of flash light.
Selecting the flash control mode to set the amount of flash
light (Flash control)
MENU button t
2 t [Flash control] t Select the desired
setting
ADI flash
This method controls the lighting of the flash, factoring in the
focus distance information and light metering data from the
pre-flash. This method enables an accurate flash
compensation with virtually no effect from the reflection off
the subject.
Pre-flash TTL
This method controls the amount of flash light depending on
the data only from pre-flash light metering. This method is
susceptible to the reflection off the subject.
ADI: Advanced Distance Integration
TTL: Through the lens
• When [ADI flash] is selected, using a lens that is provided with a distance
encoder feature can perform more accurate flash compensation by using
more accurate distance information.
104
Notes
• When the distance between the subject and the external flash (sold separately)
cannot be determined (wireless flash shooting using an external flash (sold
separately), shooting with an off-camera flash using a cable, shooting with a macro
twin flash, etc.), the camera automatically selects Pre-flash TTL mode.
• Select [Pre-flash TTL] in the following cases, as the camera cannot perform flash
compensations with ADI flash.
– A wide panel is attached to the HVL-F36AM flash.
– A diffuser is used for flash shooting.
– A filter with an exposure factor, such as an ND filter, is used.
– A close-up lens is used.
• ADI flash is only available in combination with a lens that is provided with a
distance encoder. To determine if the lens is equipped with a distance encoder, refer
to the operating instructions supplied with the lens.
Selecting the method for measuring the brightness of a
subject (Metering Mode)
Fn button t (Metering Mode) t Select the desired mode
(Multi segment) This mode measures light on each area after dividing the total
area into multiple areas and determines the proper exposure
of the entire screen.
(Center weighted) While emphasizing the central area of the screen, this mode
measures the average brightness of the entire screen.
(Spot)
This mode measures light only in the spot metering circle
located in the center area.
Shooting techniques
• Use [Multi segment] metering for general shooting.
• When there is a high contrast subject in the AF area, measure the light of
the subject you want to shoot with the optimal exposure using the spot
metering function and take advantage of an AE lock shooting (page 100).
Note
• When the exposure mode is set to AUTO, AUTO+, or Scene Selection, [Metering
Mode] is fixed to [Multi segment] and you cannot select other modes.
105
Setting ISO
Sensitivity to light is expressed by the ISO number (recommended
exposure index). The larger the number, the higher the sensitivity.
1 Press ISO on the control button to
display the ISO screen.
2 Select the desired setting with v/V on the control button.
• The larger the number, the higher the noise level.
• If you select [Multi Frame NR], select the desired value with b/B.
Notes
• When the exposure mode is set to AUTO, AUTO+, Sweep Panorama, or Scene
Selection, ISO is fixed to AUTO and you cannot select other ISO numbers.
• When the exposure mode is set to P/A/S and ISO is set to [AUTO], ISO is
automatically set between ISO 100 and ISO 1600.
• The [AUTO] setting is not provided in exposure mode M. If you change the
exposure mode to M with the [AUTO] setting, it is switched to [100]. Set the ISO
according to your shooting conditions.
Multi frame noise reduction (Multi Frame NR)
The camera automatically shoots multiple images continuously, combines
the images, reduces the noise, and records one image. In Multi Frame NR,
you can select larger ISO numbers than the maximum ISO sensitivity.
The image recorded is one combined image.
Notes
• Press and hold the shutter button until the continuous shooting stops.
• When [Image: Quality] is set to [RAW] or [RAW & JPEG], this function cannot be
used.
• The flash, D-Range optimizer, and [Auto HDR] cannot be used.
106
Compensating for the brightness and
contrast automatically (D-Range)
D-RANGE button
D-RANGE button t Select the
desired setting
(Off)
Does not use the DRO/Auto HDR functions.
(D-
By dividing the image into small areas, the camera analyses
the contrast of light and shadow between the subject and the
background, producing the image with the optimal brightness
and gradation.
RangeOptimizer)
(Auto HDR)
Shoots three images with different exposures, and then
overlays correctly exposed image, the bright areas of an
under exposed image and the dark areas of an over exposed
image to create an image with rich gradation.
Two images are recorded: an image with the correct exposure
and an overlaid image.
Correcting the brightness of the image (D-Range
Optimizer)
1 D-RANGE button t
(D-RangeOptimizer)
2 Select an optimal level with b/B on the control button.
(Auto)
(Level)*
Corrects the brightness automatically.
Optimizes the gradations of a recorded image in each area of
the image. Select the optimal level between Lv1 (weak) and
Lv5 (strong).
* Lv_ displayed with
is the step currently selected.
107
Notes
• The setting is fixed to [Off] when [Sunset], [Night View], [Night Portrait], or [Hand-
held Twilight] is selected in Scene Selection. The setting is fixed to [Auto] when
other modes are selected in Scene Selection.
• When shooting with the D-Range optimizer, the image may be noisy. Select the
proper level by checking the recorded image, especially when you enhance the
effect.
Compensating automatically with rich gradation (Auto High
Dynamic Range)
1 D-RANGE button t
(Auto HDR)
2 Select an optimal level with b/B on the control button.
(Auto Exposure
Diff.)
Corrects the exposure difference automatically.
(Exposure
Difference Level)*
Sets the exposure difference, based on the contrast of the
subject. Select the optimal level between 1.0Ev (weak) and
6.0Ev (strong).
For example: When 2.0Ev is selected, three images are
overlaid: an image with –1.0Ev, an image with the correct
exposure, and an image with +1.0Ev.
* _Ev displayed with
is the step currently selected.
Shooting technique
• Since the shutter is released three times for one shot, be careful about the
following:
– Use this function when the subject is motionless or does not blink.
– Do not recompose.
Notes
• You cannot use this function on RAW images.
• When the exposure mode is set to AUTO, AUTO+, Sweep Panorama, or Scene
Selection, you cannot select [Auto HDR].
108
• You cannot select [Auto HDR] during Smile Shutter. If you turn on the Smile
Shutter function with [Auto HDR] selected, the camera will temporarily use with the
DRO setting.
• You cannot start the next shoot until the capture process is completed after you
shoot.
• You may not obtain a desired effect depending on the luminance difference of a
subject and the shooting conditions.
• When the flash is used, this function has little effect.
• When the contrast of the scene is low or when camera shake or subject blur is
occurred, you may not obtain good HDR images. If the camera has detected a
problem,
is indicated on the recorded image to inform you of this situation.
Shoot again, as necessary, paying attention to the contrast or blur.
109
Image processing
Selecting your desired image processing (Creative Style)
In addition to the desired image processing, you can adjust the exposure
(shutter speed and aperture) as you like with [Creative Style], unlike Scene
Selection where the camera adjusts the exposure.
1 Fn button t
(Creative Style) t Select the desired
setting
2 When you want to adjust (Contrast), (Saturation), or
(Sharpness), select the desired item with b/B on the control
button, then adjust the value with v/V.
(Standard)
(Vivid)
For shooting various scenes with rich gradation and beautiful
colors.
The saturation and contrast are heightened for shooting
striking images of colorful scenes and subjects such as
flowers, spring greenery, blue sky, or ocean views.
(Portrait)
For shooting the skin color in a soft tone, ideally suited to
shooting portraits.
(Landscape) The saturation, contrast, and sharpness are heightened for
shooting vivid and crisp scenery. Distant landscapes also
stand out more.
(Sunset)
(Black &
For shooting the beautiful red of the setting sun.
For shooting images in black and white monotone.
White)
110
(Contrast), (Saturation), and
Creative Style item.
(Sharpness) can be adjusted for each
(Contrast)
The higher the value selected, the more the difference of light
and shadow is accentuated, thus making an impact on an
image.
(Saturation)
(Sharpness)
The higher the value selected, the more vivid the color. When
a lower value is selected, the color of the image is restrained
and subdued.
Adjusts the sharpness. The higher the value selected, the
more the contours are accentuated, and the lower the value
selected, the more the contours are softened.
Notes
• When the exposure mode is set to AUTO, AUTO+, or Scene Selection, [Creative
Style] is fixed to [Standard] and you cannot select other settings.
• When [Black & White] is selected, you cannot adjust the saturation.
Changing the range of color reproduction (Color Space)
The way colors are represented with combinations of numbers or the range
of color reproduction is called “color space.” You can change the color
space, depending on your purpose.
MENU button t
2 t [Color Space] t Select the desired
setting
sRGB
This is the standard color space of the digital camera. Use
sRGB in normal shooting, such as when you intend to print
out the images without any modification.
AdobeRGB
This has a wide range of color reproduction. When a large
part of the subject is vivid green or red, Adobe RGB is
effective.
• The file name of the image starts with “_DSC.”
Notes
• Adobe RGB is for applications or printers that support color management and
DCF2.0 option color space. Using some applications or printers that do not support
them may result in or print images that do not faithfully reproduce the color.
• When displaying images that were recorded with Adobe RGB on the camera or non-
Adobe RGB-compliant devices, the images are displayed with low saturation.
111
Adjusting the color tones (White balance)
The color tone of the subject changes depending on the characteristics of
the light source. The table below shows how the color tone changes based
on various light sources, compared with a subject that appears white under
the sunlight.
Daylight
Cloudy
Fluorescent
Incandescent
Weather/
lighting
Characteristics
of light
White
Bluish
Green-tinged
Reddish
White balance is a feature that adjusts the color tone to approximate what
you see. Use this feature when the color tone of the image did not come out
as you expected, or when you want to change the color tone on purpose for
photographic expression.
Notes
• When the exposure mode is set to AUTO, AUTO+, or Scene Selection, [White
Balance] is fixed to [Auto WB] and you cannot select other modes.
• If the only light source available is a mercury lamp or a sodium lamp, the camera
will not be able to acquire the accurate white balance because of the characteristics
of the light source. Use the flash in such cases.
Adjusting the white balance to suit a specific light source
(Auto/Preset white balance)
WB on the control button t Select
the desired setting
• When [AWB] is not selected, you can
fine tune the color tone with b/B.
Adjusting it toward + turns the image
reddish and adjusting it toward – turns
the image bluish.
112
AWB (Auto WB)
The camera automatically detects a light source and adjusts
the color tones.
(Daylight)
(Shade)
If you select an option to suit a specific light source, the color
tones are adjusted for the light source (preset white balance).
(Cloudy)
(Incandescent)
(Fluorescent)
(Flash)
Shooting techniques
• Use the white balance bracket function if you cannot get the desired color
in the selected option (page 119).
• When you select [5500K] (Color Temp.) or [0] (Color Filter), you can
adjust the value to the desired value (below).
• When you select [Custom], you can register your setting (page 114).
Setting the color temperature and a filter effect (Color
Temperature/Color Filter)
WB on the control button t
[5500K] (Color Temp.) or [0] (Color
Filter)
• To set the color temperature, select the
value with b/B.
• To set the color filter, select the
compensation direction with b/B.
Note
• Since color meters are designed for film cameras, the values differ under fluorescent/
sodium lamp/mercury lamps. We recommend that you use the custom white balance
or do a test shooting.
113
5500K*1 (Color
Temp.)
Sets the white balance by the color temperature. The higher
the number, the more reddish the image and the lower the
number, the more bluish the image.
0*2 (Color Filter)
Achieves the effect of CC (Color Compensation) filters for
photography.
Based on using the set color temperature as the standard, the
color can be compensated to G (Green) or M (Magenta).
*1 The value is the color temperature value currently selected.
*2 The value is the color filter value currently selected.
Registering the color tones (Custom white balance)
In a scene where the ambient light consists of multiple types of light source,
use of custom white balance is recommended in order to accurately
reproduce the whiteness.
1 WB on the control button t
(Custom)
2 Select [
SET] with b/B on the control button, then press the
center of the control button.
3 Hold the camera so that the white area fully covers the AF area
located in the center, and then press the shutter button down.
The shutter clicks and the calibrated values (ColorTemperature and Color
filter) are displayed.
4 Press the center of the control button.
The monitor returns to the recording information display with the memorized
custom white balance setting retained.
• The custom white balance setting registered in this operation is effective
until a new setting is registered.
114
Note
• The message “Custom WB error” indicates that the value is beyond the expected
range. (When the flash is used on a subject in close proximity or a subject with a
bright color is in the frame.) If you register this value, the
indicator turns yellow
on the recording information display. You can shoot at this point, but it is
recommended that you set the white balance again to get a more correct white
balance value.
To call the custom white balance setting
WB on the control button t
(Custom)
Note
• If the flash is used when the shutter button is pressed, a custom white balance is
registered with the flash light taken into account. Take pictures with the flash in later
shootings.
115
Selecting the drive mode
This camera has six drive modes, such as single-shot advanced, and
continuous advanced. Use them to suit your purpose.
Shooting single shot
This mode is for normal shooting.
on the control button t
(Single-shot Adv.)
Note
• When the exposure mode is set to [Sports Action] in Scene Selection, you cannot
shoot single shot.
Shooting continuously
The camera records the images continuously at the following speeds*.
SLT-A55/A55V
SLT-A33
Maximum 6 images per second
Maximum 3 images per second
Maximum 6 images per second
Maximum 2.5 images per second
* Our measurement conditions. The speed of continuous shooting is slower,
depending on shooting conditions.
1
on the control button t
(Continuous adv.) t Select
the desired speed
2 Adjust the focus and shoot the subject.
• When you press and hold the shutter button, the recording continues.
116
The maximum number of continuous shots
The number of continuous shooting images obtainable has an upper limit.
SLT-A55/A55V
28 images
28 images
19 images
19 images
SLT-A33
14 images
16 images
7 images
7 images
Fine
Standard
RAW & JPEG
RAW
Shooting technique
• To shoot continuously faster, set the exposure mode to Continuous
Notes
• When
is selected, the image recorded between the frames is displayed.
• You cannot shoot continuously when using Scene Selection modes other than
[Sports Action].
• When [Face Detection] is set to [On], the speed of continuous shooting may be
slower.
Using the self-timer
The 10-second self-timer is convenient when the photographer appears in a
photo and the 2-second self-timer is convenient to reduce the camera shake.
1
on the control button t
(Self-timer) t Select the
desired setting
• The number after
is the number of
seconds that is currently selected.
2 Adjust the focus and shoot the subject.
• When the self-timer is activated, audio signals and the self-timer lamp
indicate the condition. The self-timer lamp flashes quickly and the audio
signal sounds quickly right before the shooting.
117
To cancel the self-timer
Press
on the control button.
Shooting images with the exposure shifted (Exposure
bracket)
– direction
+ direction
Base exposure
Bracket shooting allows you to shoot several images, each with different
degrees of exposure. Specify the value of deviation (steps) from the base
exposure, and the camera shoots three images while automatically shifting
the exposure. Press and hold the shutter button until the shooting stops.
When the flash is fired, flash bracket shooting is used to shift the amount of
flash light. To shoot, press the shutter button shot by shot.
1
on the control button t
(Bracket: Cont.) t Select
the desired bracket step
2 Adjust the focus and shoot the subject.
The base exposure is set at the first shot in the bracket.
• Press and hold the shutter button until recording stops. In flash bracket
shooting, press the shutter button three times.
Notes
• When the mode dial is set to M, the exposure is shifted by adjusting the shutter
speed.
• When you adjust the exposure, the exposure is shifted based on the compensated
value.
• The bracket cannot be used when the exposure mode is set to AUTO, AUTO+,
Sweep Panorama, or Scene Selection.
118
The EV scale in bracket shooting
Ambient light* bracket
Flash bracket
0.3 steps, three shots
Exposure compensation 0
0.7 steps, three shots
Flash compensation –1.0
LCD monitor/
Viewfinder
LCD monitor (When
[Display Rec. Data] is
set to [For viewfinder])
Shown in the top row.
Shown in the bottom row.
* Ambient light: Any light other than the flash light that shines on the scene
for an extended period of time, such as natural light, a light bulb, or a
fluorescent light.
• In bracket shooting, the same number of indices as the number of
recordable images is displayed on the EV scale.
• When the bracket shooting starts, the indices that indicate already
recorded images start to disappear one by one.
Shooting with white balance shifted (WB bracket)
Based on the selected white balance, and the color temperature/color filter,
three images are recorded with the white balance shifted.
1
on the control button t
(WB bracket) t Select
the desired setting
• When Lo is selected, it is shifted by 10
mired*, and when Hi is selected, it is
shifted by 20 mired.
2 Adjust the focus and shoot the subject.
* Mired: a unit to indicate the color conversion quality in color temperature filters.
119
Shooting with the Wireless Remote Commander
You can shoot using the SHUTTER and 2SEC (the shutter is released after
2 seconds) buttons on the RMT-DSLR1 Wireless Remote Commander
(sold separately). Also, refer to the operating instructions supplied with the
Wireless Remote Commander.
1
on the control button t
(Remote Cdr.)
2 Focus on the subject, point the transmitter of the Wireless
Remote Commander to the remote sensor, and shoot the
image.
120
Using the viewing function
Playing back images
The last recorded image is displayed on the LCD monitor.
1 Press the
button.
button
2 Select an image with b/B on the control button.
To return to the shooting mode
Press the
button again.
To switch the recording data display
Press DISP on the control button.
Each time you press DISP on the control button, the screen changes as
follows.
Without recording
data
With recording data
Histogram display
To select the folder to be played back
MENU button t
2 t [Select Folder] t Select the desired
folder
To select the orientation when playing back an image recorded in the
portrait position
MENU button t
2 t [Playback Display] t Select the
desired setting
121
Note
• When you play back the image on a TV or a computer, the image will be displayed
in the portrait position even if [Manual Rotate] is selected.
To scroll panoramic images
Select a panoramic image, then press the center of the control button.
Pressing it again pauses the playback.
3D Sweep Panorama images cannot be scrolled. Scrolling playback is not
available for images that were recorded with [3D Pan.: Image Size] set to
[16:9].
Playing back movies
1 MENU button t
1 t [Still/Movie Select] t [Movie]
2 Select the desired movie with b/B on the control button, then
press the center of the control button.
During movie playback
To pause/resume
To fast-forward
Control button/control dial operation
z
B
b
To fast-rewind
To slow-forward
Rotate the control dial to the right during
pause
To slow-reverse
Rotate the control dial to the left during
pause
To adjust sound volume
V t v/V
To display the information
v
To adjust the volume
MENU button t
2 t [Volume Settings] t Select the
desired valve
122
To select the date of movies to be played back
Movies are stored by date.
MENU button t
2 t [Select Date] t Select the desired
date
Note
• Movies recorded with other devices may not be played back on this camera.
Rotating an image
1 Display the image you want to
rotate, then press the
button.
button
2 Press the center of the control button.
The image is rotated counter-clockwise. When you want to do another
rotation, repeat step 2.
• Once you rotate the image, the image is played back in the rotated position,
even if you turn off the power.
To return to the normal playback screen
Press the
button.
Notes
• You cannot rotate movies.
• When you copy rotated images to a computer, “PMB” contained on the CD-ROM
(supplied) can display the rotated images correctly. However, the images may not be
rotated depending on the software.
123
Enlarging images
A still image can be enlarged for closer examination. This is convenient to
check the focus condition of a recorded image.
1 Display the image you want to
enlarge, then press the button.
button
2 Zoom the image in or out with the
button or button.
• Rotating the control dial switches the
image at the same display
magnification. When you shoot
multiple images with the same
button
composition, you can compare their
focus conditions.
3 Select the portion you want to enlarge with v/V/b/B on the
control button.
To cancel the enlarged playback
Press the
button so that the image returns to the normal size.
Scaling range
The scaling range is as follows.
Scaling range
Image size
SLT-A55/A55V
SLT-A33
L
Approx. ×1.1 – ×11.8
Approx. ×1.1 – ×8.8
Approx. ×1.1 – ×6.0
Approx. ×1.1 – ×11.8
Approx. ×1.1 – ×8.0
Approx. ×1.1 – ×5.5
M
S
124
Switching to the display of the image list
MENU button t
1 t [Image Index] t Select the desired
number of images to be displayed on one page
• You can also display the image list using the
button.
To return to the single-image screen
Press the center of the control button when you select the desired image.
To turn to the movie index screen
To display movies on the image index
screen, select
(movie) on the tab with
b/B on the control button, then press the
center of the control button.
Still image/movie switching tab
Playing back images automatically (Slide show)
MENU button t 1 t [Slide Show]t [Enter]
Plays back recorded images in order (Slide show). The slide show
automatically stops after all the images have been played back.
• You can view the previous/next image with b/B on the control button.
• You cannot pause the slide show.
To end in the middle of the slide show
Press the center of the control button.
To choose the interval between the images in slide show
MENU button t
1 t [Slide Show] t [Interval] t Select
the desired number of seconds
To play back repeatedly
MENU button t
1 t [Slide Show] t [Repeat] t [On]
125
To play back movies
You cannot play back still images and movies in the same slide show.
Switch to a movie playback with [Still/Movie Select], then select the movie
type.
MENU button t
1 t [Slide Show] t [Movie Type] t
Select the desired movie type
To play back 3D-images
If you connect the camera to a 3D-compatible TV using an HDMI cable
(sold separately), you can play back 3D-images recorded with the 3D
refer to the operating instructions supplied with the TV.
MENU button t
1 t [Slide Show] t [Image Type] t
[Display 3D Only]
126
Checking the information of recorded
images
Each time you press DISP on the control button, the information display
Basic information display
Still image
Movie
A
Display
DPOF3
Indication
Display
Indication
Remaining battery
warning (22)
Memory card (20)
Still image/Movie
100-0003 Folder - file number
Database file full (190)/
Database file error (190)
2010 1 1
Recording date
Overheating warning
Image size of still images
(141)/Aspect ratio of still
of panoramic images
AVCHD
MP4
Movie file format (82)
Image size of movies
Image quality of still
images (143)
-
Protect (131)
127
B
Display
Indication
GPS information (SLT-
A55V only)
N35° 37’
32”
Latitude and longitude
display (SLT-A55V only)
W139° 44’
31”
2010 1 1 Date of recording
10:37AM
Auto HDR image
warning (108)
1/125
F3.5
Shutter speed (75)
Aperture (72)
ISO200
3/7
ISO sensitivity (106)
File number/total number
of images
N
Playback
Playback bar
Counter
5:40
C
Display
Indication
Volume
128
Histogram display
A
B
Display
Indication
Display
Indication
Memory card (20)
Still image
Histogram* (102)
•
(SLT-A55/A55V)/
(SLT-A33)
100-0003 Folder - file number
P A
S M
Image size of still images
(141)/Aspect ratio of still
of panoramic images
1/125
F3.5
Shutter speed (75)
Aperture (72)
ISO200
ISO sensitivity (106)
–0.3
Exposure compensation
Image quality of still
images (143)
–0.3
Flash compensation (103)
Metering mode (105)
Focal length (176)
-
Protect (131)
35mm
DPOF3
DPOF set (172)
Creative Style (110)
Remaining battery
warning (22)
AWB +1 White balance (Auto,
5500K M1 Preset, Color
temperature, Color filter,
Custom) (112)
Database file full (190)/
Database file error (190)
Overheating warning
D-Range Optimizer
HDR image warning
129
Display
Indication
2010 1 1 Date of recording
10:37AM
3/7
File number/total number
of images
* When the image has a high-key or
low-key portion, that portion is flashed
on the histogram display (Luminance
limit warning).
130
Protecting images (Protect)
You can protect images against accidental erasure.
Protecting selected images/canceling the protection of the
selected images
1 MENU button t
1 t [Protect] t [Multiple Img.]
2 Select the image you want to
protect with b/B on the control
button, then press the center of
the control button.
-
A - mark appears on the selected
image.
• To cancel a selection, press the center
again.
3 To protect other images, repeat step 2.
4 Press the MENU button.
5 Select [Enter] with v, then press the center of the control
button.
To cancel the protection of all the images or movies
You can cancel the protection of all the images in the folder currently
selected or of all the movies with the same date.
MENU button t
1 t [Protect] t [Cancel All Images] or
[Cancel All Movies]
131
Deleting images (Delete)
Once you have deleted an image, you cannot restore it. Check whether to
delete the image or not beforehand.
Note
• Protected images cannot be deleted.
Deleting the image that is currently displayed
1 Display the image you want to
delete and press the
button.
button
2 Select [Delete] with v on the control button, then press the
center of the control button.
Deleting the selected images
1 MENU button t
1 t [Delete] t [Multiple Img.]
2 Select the images you want to
delete with the control button,
then press the center of the
control button.
A
mark appears on the selected
image.
Total number
3 To delete other images, repeat step 2.
132
4 Press the MENU button.
5 Select [Delete] with v, then press the center of the control
button.
Deleting all the images in the folder
Deletes all still images in the folder. This appears during still image
playback only.
1 MENU button t
1 t [Delete] t [All in Folder]
2 Select [Delete] with v on the control button, then press the
center of the control button.
Deleting all the movies with the same date
Deletes all movies of that date. This appears during movie playback only.
1 MENU button t
1 t [Delete] t [All in Date Rng.]
2 Select [Delete] with v on the control button, then press the
center of the control button.
133
Viewing images on a TV screen
To view images recorded on the camera on a TV set, an HDMI cable (sold
separately) and an HD TV equipped with an HDMI connector are required.
1 Turn off both your camera and the 1 To the HDMI
connector
TV, and connect the camera to the
TV.
HDMI cable
(sold separately)
2 To the
HDMI terminal
2 Turn on the TV and switch the input.
• See also the operating instructions supplied with the TV.
3 Turn on the camera.
Images shot with the camera appear on
the TV screen.
Select the desired image with b/B on the
control button.
• The LCD monitor on the camera does
not turned on.
Control button
Notes
• Use an HDMI cable with the HDMI logo.
• Use an HDMI mini connector on one end (for the camera), and a connector suitable
for connection to your TV on the other end.
• Some devices may not work properly.
134
• Do not connect the output connector of the device with the HDMI terminal on the
camera. This may cause a malfunction.
On “PhotoTV HD”
This camera is compatible with the “PhotoTV HD” standard.
By connecting Sony’s PhotoTV HD-compatible devices using an HDMI
cable, a whole new world of photos can be enjoyed in breathtaking Full HD
quality.
“PhotoTV HD” allows for a highly-detailed, photo-like expression of
subtle textures and colors.
On “<BRAVIA> Photo Map”
This camera is compatible with the “<BRAVIA> Photo Map” standard.
By connecting the camera to a TV that supports “<BRAVIA> Photo Map”
using a USB cable, you can display the shooting location on the map when
the image is recorded with the location information.
To view 3D-images with a 3D-compatible TV
If you connect the camera to a 3D-compatible TV using an HDMI cable
(sold separately), you can play back 3D-images recorded with the 3D
Sweep Panorama mode automatically. For details on 3D-shooting, see page
198. Also refer to the operating instructions supplied with the TV.
MENU button t
1 t [3D Viewing]
135
Using “BRAVIA” Sync
By connecting the camera to a TV that supports “BRAVIA” Sync using an
HDMI cable, you can operate the camera with the TV Remote Control.
1 Connect a TV that supports “BRAVIA” Sync to the camera
The input is automatically switched and the image shot with the camera
appears on the TV screen.
2 Press the SYNC MENU button on the TV Remote Control.
3 Operate with the buttons on the TV Remote Control.
The items for Sync Menu
Slide Show
Returns to the single-image screen.
Single-image
playback
Still/Movie Select
Image Index
Selects still images or movies to be played back.
Switches to the image index screen.
3D Viewing
Plays back 3D-images when connected to a 3D-compatible
TV.
Select Folder
Select Date
Delete
Selects the folder of images to be played back.
Selects the date of movies to be played back.
Deletes images.
Notes
• The operations available are restricted when the camera is connected to a TV using
an HDMI cable.
• Only TVs that support “BRAVIA” Sync can provide these operations. The SYNC
Menu operations differ depending on the TV connected. For details, refer to the
operating instructions supplied with the TV.
• If the camera performs unnecessary operations in response to the TV Remote
Control when the camera is connected to another manufacturer’s TV using an HDMI
connection, set [CTRL FOR HDMI] in the
Setup menu to [Off].
136
To use your camera abroad
When you view images on a TV screen, the camera and TV must use the
same TV color system.
NTSC system (1080 60i)
Bahama Islands, Bolivia, Canada, Central America, Chile, Colombia, Ecuador,
Jamaica, Japan, Korea, Mexico, Peru, Surinam, Taiwan, the Philippines, the U.S.A.,
Venezuela, etc.
PAL system (1080 50i)
Australia, Austria, Belgium, China, Croatia, Czech Republic, Denmark, Finland,
Germany, Holland, Hong Kong, Hungary, Indonesia, Italy, Kuwait, Malaysia, New
Zealand, Norway, Poland, Portugal, Rumania, Singapore, Slovak Republic, Spain,
Sweden, Switzerland, Thailand, Turkey, United Kingdom, Viet Nam, etc.
PAL-M system (1080 50i)
Brazil
PAL-N system (1080 50i)
Argentina, Paraguay, Uruguay
SECAM system (1080 50i)
Bulgaria, France, Greece, Guiana, Iran, Iraq, Monaco, Russia, Ukraine, etc.
137
Changing your setup
GPS setting (SLT-A55V only)
If the camera has acquired location information using the built-in GPS
feature, this information is recorded in the images or movies at that
location.
Using the supplied software “PMB,” you can import images recorded with
location information to a computer and enjoy viewing them with a map
which shows their shooting location. See “PMB Help” for details.
MENU button t
1 t [GPS Settings] t [GPS On/Off] t [On]
The indicator changes according to the strength of GPS signal reception.
GPS indicators GPS reception status
No indicator
[GPS On/Off] is set to [Off].
Your camera cannot record the location information. Use your
camera in an open area.
Calculating the location information. Wait until the location
information is recordable.
The last acquired location information will be recorded. To record
the correct location information, use your camera in an open area.
The current location information is recordable.
There is a problem with the GPS feature. Turn the camera off and
on.
To receive a GPS signal
• Proper triangulation is not possible indoors or near tall buildings.
Use your camera in an open area outside, and turn on your camera again.
• It may take several tens of seconds to several minutes to acquire the
location information. You can shorten the positioning time by using GPS
assist data.
Notes
• During take off and landing of an airplane, turn off the camera, as you will be
instructed to do by the on-board announcement.
• Use GPS in accordance with the regulations of the place or situation.
• For detailed notes on the GPS feature, see page 196.
138
Shortening the time needed for the GPS to acquire location
information (GPS assist data)
The time for the GPS acquiring location information can be shortened by
taking in GPS assist data.
If the camera connects to the computer that the supplied “PMB” software
has been installed, the GPS assist data can be updated automatically.
To check the state of GPS assist data
MENU button t
1 t [GPS Settings] t [Use GPS Assist
Data]
To delete GPS assist data
MENU button t
1 t [GPS Settings] t [Delete GPS Ass.
Data]
Notes
• The computer is required to connect to the Internet when updating data.
• If the term of validity of assist data has run out, the time until you can record
location information cannot be shortened. It is recommended that you update the
assist data regularly. The expiration date of the assist data is about 30 days.
• If [Date/Time Setup] is not set, or set time is shifted greatly, the time for the GPS
acquiring location information cannot be shortened.
• The assist data service may be closed for various reasons.
To update the GPS assist data by inserting a memory card into the
computer
Start up [GPS Support Tool] from
(PMB Launcher), select the memory
card drive from your computer, and then update the GPS assist data. Insert
the memory card that has been updated into the camera.
139
Correcting clock time automatically
Your camera maintains correct clock time by using GPS to acquire time
information during starting up. The time is corrected when the power is
turned off.
MENU button t
1 t [GPS Settings] t [GPS Auto Time Cor.]
t [On]
Notes
• [GPS Auto Time Cor.] is invalid if [GPS On/Off] is set to [Off].
• You must set [Date/Time Setup] on the camera before using it.
• There may be discrepancies of a few seconds.
• Depending on the area, it may not function correctly.
140
Setting image size and image quality
Image: Size
MENU button t
1 t [Image: Size] t Select the desired
size
[Image: Aspect Ratio]: [3:2]
SLT-A55/A55V
Image size
Usage guidelines
L:16M
4912 × 3264 pixels
For prints up to A3+ size
For prints up to A4 size
For prints L/2L size
M:8.4M
S:4.0M
3568 × 2368 pixels
2448 × 1624 pixels
SLT-A33
Image size
L:14M
Usage guidelines
4592 × 3056 pixels
3344 × 2224 pixels
2288 × 1520 pixels
For prints up to A3+ size
For prints up to A4 size
For prints L/2L size
M:7.4M
S:3.5M
[Image: Aspect Ratio]: [16:9]
SLT-A55/A55V
Image size
Usage guidelines
L:14M
4912 × 2760 pixels
For viewing on a high-definition
TV
M:7.1M
S:3.4M
3568 × 2000 pixels
2448 × 1376 pixels
SLT-A33
Image size
L:12M
Usage guidelines
4592 × 2576 pixels
3344 × 1872 pixels
2288 × 1280 pixels
For viewing on a high-definition
TV
M:6.3M
S:2.9M
Note
• When you select a RAW image with [Image: Quality], the image size of the RAW
image corresponds to L. This size is not displayed on the screen.
141
Setting the size of panoramic images
You can set the image size of panoramic images. The image size varies
depending on the [Panorama: Direction] or [3D Panorama: Size] setting
MENU button t
2 t [Panorama: Size] or [3D Pan.: Image
Size] t Select the desired size
[Panorama: Size]
(Standard)
Vertical: 3872 × 2160
Horizontal: 8192 × 1856
(Wide)
Vertical: 5536 × 2160
Horizontal: 12416 × 1856
[3D Pan.: Image Size]
(16:9)
Horizontal: 1920 × 1080
(Standard) Horizontal: 4912 × 1080
(Wide)
Horizontal: 7152 × 1080
Movie: Size
The larger the image size, the higher the image quality.
MENU button t
1 t [Movie: Size] t Select the desired
size
[AVCHD] mode
(1920 × 1080) 17 Mbps: Records with the highest image quality for viewing
on a high-definition TV.
[MP4] mode
(1440 × 1080) 12 Mbps: Records with high image quality for viewing on a
high-definition TV.
(VGA) (640 × 3 Mbps: Records in the suitable size for WEB uploads.
480)
142
Note
• A telephoto image results except when the [VGA] image size is selected for movies
(SLT-A33 only).
Image: Aspect Ratio
MENU button t
1 t [Image: Aspect Ratio] t Select the
desired ratio
3:2
A normal ratio.
An HDTV ratio.
16:9
Note
• This item cannot be set when the exposure mode is set to Sweep Panorama.
Image: Quality
MENU button t
1 t [Image: Quality] t Select the desired
setting
(RAW)
File format: RAW (Records using the RAW compression
format.)
This format does not perform any digital processing on the
images. Select this format to process images on a computer
for professional purposes.
• The image size is fixed to the maximum size. The image
size is not displayed on the screen.
(RAW &
JPEG)
File format: RAW (Records using the RAW compression
format.) + JPEG
A RAW image and a JPEG image are created at the same
time. This is suitable when you need two image files, a JPEG
for viewing, and a RAW for editing.
• The image quality is fixed to [Fine] and the image size is
fixed to [L].
(Fine)
File format: JPEG
The image is compressed in the JPEG format when recorded.
Since the compression rate of
(Standard)
(Standard) is higher than
that of
of
(Fine), the file size of is smaller than that
. This will allow more files to be recorded on one
memory card, but the image quality will be lower.
143
Notes
• This item cannot be set when the exposure mode is set to Sweep Panorama.
• For details on the number of images that can be taken when the image quality is
About RAW images
You need the “Image Data Converter SR” software included on the CD-ROM
(supplied) in order to open a RAW image recorded on this camera. With this software,
a RAW image can be opened and converted to a common format, such as JPEG or
TIFF, and its white balance, color saturation, contrast, etc., can be readjusted.
• The RAW format image cannot be printed using a DPOF (print) designated printer.
• You cannot set [Auto HDR] on RAW format images.
144
Setting the method for recording on a
memory card
Selecting the method for assigning file numbers to images
MENU button t
1 t [File Number] t Select the desired
setting
Series
The camera does not reset numbers and assigns numbers to
files in sequence until the number reaches “9999.”
Reset
The camera resets numbers in the following cases and assigns
numbers to files from “0001.” When the recording folder
contains a file, a number one higher than the largest number
is assigned.
– When the folder format is changed.
– When all the images in the folder are deleted.
– When the memory card is replaced.
– When the memory card is formatted.
Selecting the folder name format
The recorded still images are stored in automatically-created folders in the
DCIM folder of the memory card.
MENU button t
1 t [Folder Name] t Select the desired
setting
Standard Form
The folder name format is as follows: folder number +
MSDCF.
Example: 100MSDCF
Date Form
The folder name format is as follows: folder number + Y (the
last digit)/MM/DD.
Example: 10000405 (Folder name: 100, date: 2010/04/05)
Note
• The movie folder form is fixed as “folder number + ANV01.”
145
Creating a new folder
You can create a folder in a memory card for recording images.
A new folder is created with a number incremented one higher than the
largest number currently used, and the folder becomes the current recording
folder. A folder for still images and a folder for movies are created at the
same time.
MENU button t
1 t [New Folder]
Notes
• When you insert a memory card that was used with other equipment into the camera
and shoot images, a new folder may be automatically created.
• Up to 4 000 images can be stored in a folder. When the folder capacity is exceeded, a
new folder is created automatically.
Selecting the recording folder
When a standard form folder is selected and there are two or more folders,
you can select the recording folder to be used to record images.
MENU button t
1 t [Select REC Folder] t Select the
desired folder
Notes
• You cannot select the folder when you select the setting [Date Form].
• You cannot select the folder for movies.
Formatting the memory card
Note that formatting irrevocably erases all data on a memory card,
including protected images.
MENU button t
1 t [Format] t [Enter]
Notes
• During the format, the access lamp lights up. Do not eject the memory card while the
lamp is lit.
• Format the memory card using the camera. If you format it on a computer, the
memory card may not be usable with the camera, depending on the format type used.
• Formatting may take several minutes depending on the memory card.
146
Recovering image database
When inconsistencies are found in the image database file of movies,
caused by processing movies on computers, etc., movies on the memory
card will not be played back in this form. If this happens, the camera repairs
the file.
MENU button t
1 t [Recover Image DB] t [Enter]
Note
• Use a sufficiently charged battery. Low battery power during repairing can cause
damage to data.
Checking the remaining space of the card
Displays the remaining recording time of movies and the number of
recordable still images on the memory card.
MENU button t
1 t [Display Card Space]
Setting the upload function for an Eye-Fi card
Sets whether or not you use the upload function when using an Eye-Fi card
(commercially available). This item appears when an Eye-Fi card is
inserted in the camera.
MENU button t
2 t [Upload Settings] t Select the desired
setting
The status indicators in communication
Standby. No images are to be sent.
Upload standby.
Connecting.
Uploading.
Error
147
Notes
• Before using an Eye-Fi card, set up the wireless LAN access point and forwarding
destination. For details, refer to the operating manual supplied with the Eye-Fi card.
• Eye-Fi cards are sold in the U.S.A, Canada, Japan, and some countries in the EU (as
of March in 2010).
• For more information, please contact the manufacturer or vendor directly.
• Eye-Fi cards can be used only in the countries/regions where they were purchased.
Use Eye-Fi cards in accordance with the law of the countries/regions where you
purchased the card.
• Eye-Fi cards include a wireless LAN function. Do not insert any Eye-Fi cards in the
camera when it is prohibited to do so, such as on an airplane. If there is an Eye-Fi
card inserted in the camera, set [Upload Settings] to [Off].
screen when [Upload Settings] is set to [Off].
is displayed on the
• When you use a brand-new Eye-Fi card for the first time, copy the install file of Eye-
Fi manager recorded on the card to your computer before formatting the card.
• Use an Eye-Fi card after updating the firmware to the latest version. For details, refer
to the manual that comes with the Eye-Fi card.
• The power save function of the camera does not work while it is uploading images.
• If
(error) is displayed, remove the memory card and reinsert it, or turn off then
appears again, the Eye-Fi card may be damaged.
turn on the power again. If
• Wi-Fi network communication may be influenced by other communication devices.
If the communication status is poor, move closer to the access point of the Wi-Fi
network.
• For details on the file types that can be uploaded, refer to the operating instructions
supplied with the Eye-Fi card.
• If you upload an image that was recorded with [GPS On/Off] set to [On], the
location information of the image may be made available to a third party. To prevent
• This product does not support the Eye-Fi “Endless Memory Mode.” Make sure that
Eye-Fi cards that you insert into this product have “Endless Memory Mode” turned
off.
148
Changing the noise reduction setting
Disabling the noise reduction during long exposure
shootings
When you set the shutter speed to a second or longer (Long exposure
shooting), noise reduction is turned on for the same duration that the shutter
is open.
This is to reduce the grainy noise typical in a long exposure. When noise
reduction is in progress, a message appears and you cannot take another
picture. Select [On] to prioritize the image quality. Select [Off] to prioritize
the timing of shooting.
MENU button t
3 t [Long Exposure NR] t [Off]
Notes
• When the exposure mode is set to Sweep Panorama, Continuous Advance Priority
AE, or continuous shooting, continuous bracketing, [Hand-held Twilight] in Scene
Selection, or ISO is set to [Multi Frame NR], noise reduction is not performed even
when it is set to [On].
• When the exposure mode is set to AUTO, AUTO+ or Scene Selection, you cannot
turn off noise reduction.
Setting the noise reduction at high ISO sensitivity settings
The camera reduces the noise that becomes more noticeable when the
camera sensitivity is high.
Select [Auto] to prioritize the image quality. Select [Weak] to prioritize the
timing of shooting.
MENU button t
3 t [High ISO NR] t Select the desired
setting
Notes
• [Weak] is selected automatically for continuous shooting or continuous bracketing
images, even when you set it to [Auto].
• When the exposure mode is set to AUTO, AUTO+, Sweep Panorama, or Scene
Selection, you cannot select [Weak].
• Noise reduction is not performed on RAW images.
149
Changing the function of the buttons
Changing the operation of the AEL button
The function of the AEL button can be selected from the following two
functions:
– Holding the locked exposure value by pressing the AEL button while
the button is held down ([AEL hold]).
– Holding the locked exposure value by pressing the AEL button until the
button is pressed again ([AEL toggle]).
MENU button t
1 t [AEL button] t Select the desired
setting
Notes
• While the exposure value is locked,
appears on the LCD monitor and in the
viewfinder. Be careful not to reset the setting.
manual exposure mode.
• When [AEL toggle] is selected, be sure to press the AEL button again to release the
lock.
Changing the function of a focus hold button to the preview
function
If you use a lens equipped with a focus hold button, you can change the
function of the button to preview a shot.
MENU button t
1 t [Focus Hold Button] t [D.O.F.Preview]
Enabling the Focus Magnifier function
You can zoom the image to check the focus using the
shooting.
button during
MENU button t
1 t [Focus Magnifier] t [On]
150
Changing other settings
Setting the sound on/off
Selects the sound produced when the shutter is locked, during self-timer
countdown, etc.
MENU button t
2 t [Audio signals] t Select the desired
setting
Removing the Help Guide from the screen
You can turn off the Help Guide that is displayed when you operate the
camera. This is convenient when you want to perform the next operation
quickly.
MENU button t
1 t [Help Guide Display] t [Off]
Setting the time to turn the camera to the power save mode
You can set different time intervals for the camera to switch to power save
mode (Power Save). Pressing the shutter button halfway down returns the
camera to the shooting mode.
MENU button t
1 t [Power Save] t Select the desired
time
Note
• Regardless of the setting here, the camera turns to power save mode after 30 minutes
when the camera is connected to a TV or the drive mode is set to [Remote Cdr.].
Releasing the shutter when no lens is attached
You can release the shutter when no lens is attached. Select this when you
attach the camera on an astronomical telescope, etc.
MENU button t
1 t [Release w/oLens] t [Enable]
151
Note
• Correct metering cannot be achieved when you use lenses that do not provide a lens
contact, such as the lens of an astronomical telescope. In such cases, adjust the
exposure manually by checking it on the recorded image.
Selecting the language
MENU button t
1 t [ Language] t Select the language
Setting the demonstration playback of a movie
You can set the camera to start the demonstration playback of a movie if
you do not operate the camera for about one minute.
MENU button t
2 t [Demo Mode] t [On]
152
Setting the LCD monitor/electronic
viewfinder
Setting the brightness of the LCD monitor
The brightness of the LCD monitor is automatically adjusted to the
surrounding lighting conditions using the light sensor (page 15).
You can set the brightness of the LCD monitor manually or select the
setting that is suitable for outdoors on a sunny day.
MENU button t
1 t [LCD Brightness] t Select the desired
setting
Notes
• When it is set to [Auto], do not cover the light sensor with your hand and so on.
• When using the camera with the AC-PW20 AC Adaptor (sold separately), the
brightness of the LCD monitor is always set to the brightest setting even if you select
[Auto].
• Set it to [Auto] or [Manual] for interior photography because [Sunny Weather] is too
bright.
Setting the brightness of the viewfinder manually
The brightness of the viewfinder is automatically adjusted to the lighting
conditions of the subject.
You can set the brightness of the viewfinder manually.
MENU button t
1 t [Viewfinder Bright.] t [Manual] t
Select the desired setting
Note
• When using the camera with the AC-PW20 AC Adaptor (sold separately), the
brightness of the viewfinder is always set to the brightest setting even if you select
[Auto].
153
Setting the displayed time of the image right after shooting
(Auto review)
You can check the recorded image on the screen right after the shooting.
You can change the displayed time.
MENU button t
2 t [Auto Review] t Select the desired
setting
Note
• In auto review, the image will not be displayed in the vertical position even if
[Playback Display] is set to [Auto Rotate] (page 121).
Setting the method used to switch the LCD monitor and the
viewfinder
You can disable the automatic switching of the LCD monitor and the
viewfinder and enable only the FINDER/LCD button to switch them.
MENU button t
1 t [FINDER/LCD Setting] t [Manual]
Setting the grid line
The grid line is an auxiliary line for shooting composition. You can set the
grid line to on/off or select the type of grid line. The available range of
movie recording is also displayed.
MENU button t
2 t [Grid Line] t Select the desired setting
154
Confirming the version of the camera
Displays the version of your camera. Confirm the version when a firmware
update is released.
MENU button t
2 t [Version]
Note
• An update can be performed only when the battery level is
(three remaining
battery icons) or more. We recommend that you use a sufficient battery or the AC-
PW20 AC Adaptor (sold separately).
155
Resetting to the default
You can reset the main functions of the camera.
MENU button t
2 t [Reset Default] t [Enter]
The items to be reset are as follows.
Items
Reset to
Exposure compensation (101)
Recording information display (40)
Playback display (121)
0.0
Graphic Display
Single-image screen (with recording
information)
Drive mode (116)
Flash Mode (96)
Single-shot Adv.
Fill-flash (differs based on whether the
built-in flash is open or not)
AF-A
Wide
Face Detection (93)
Smile Shutter (94)
On
Off
AUTO
Metering Mode (105)
Flash Compensation (103)
White Balance (112)
Color Temp./Color Filter (113)
Custom white balance (114)
DRO/Auto HDR (107)
Creative Style (110)
Scene Selection (63)
Multi segment
0.0
AWB (Auto white balance)
5500K, Color Filter 0
5500K
D-Range Optimizer: Auto
Standard
Portrait
Recording menu
Items
Reset to
Image: Size (141)
L:16M (SLT-A55/A55V)/
L:14M (SLT-A33)
Image: Aspect Ratio (143)
Image: Quality (143)
Movie: Size (142)
3:2
Fine
1920 × 1080
156
Items
Reset to
AVCHD
On
Movie: File Format (82)
Movie: Audio Rec. (82)
SteadyShot (57)
On
Panorama: Size (142)
Panorama: Direction (68)
3D Pan.: Image Size (142)
3D Pan.: Direction (68)
Flash control (104)
AF Illuminator (98)
Color Space (111)
Standard
Right
16:9
Right
ADI flash
Auto
sRGB
On
Long Exposure NR (149)
High ISO NR (149)
Auto
Custom menu
Items
Reset to
Off
Eye-Start AF (39)
FINDER/LCD Setting (154)
AEL button (150)
Auto
AEL hold
Off
Focus Magnifier (150)
Focus Hold Button (150)
Red Eye Reduction (98)
Release w/oLens (151)
Grid Line (154)
Focus Hold
Off
Disable
Off
Histogram (102)
Off
Display Rec. Data (41)
Auto Review (154)
Auto+ Cont. Advance (62)
Auto+ Image Extract. (62)
For Live View
Off
Auto
Auto
Playback menu
Items
Reset to
3 sec
Slide Show – Interval (125)
Slide Show – Repeat (125)
Off
157
Items
Reset to
Specify Printing – Date Imprint (173)
Volume Settings (122)
Playback Display (121)
Off
2
Auto Rotate
Memory Card Tool menu
Items
Reset to
File Number (145)
Folder Name (145)
Series
Standard Form
Setup menu
Items
Reset to
Auto
Auto
On
LCD Brightness (153)
Viewfinder Bright. (153)
GPS Settings – GPS On/Off (138)
(SLT-A55V only)
GPS Settings – GPS Auto Time Cor.
(140) (SLT-A55V only)
On
1 Min
CTRL FOR HDMI (136)
Help Guide Display (151)
Upload Settings (147)
USB Connection (165)
Audio signals (151)
Demo Mode (152)
On
On
On
Mass Storage
On
Off
158
Viewing images on a computer
Using with your computer
Following applications are contained on the CD-ROM (supplied) to allow
more versatile use of images shot with your camera.
• Sony Image Data Suite
“Image Data Converter SR”
“Image Data Lightbox SR”
• “PMB” (Picture Motion Browser)
Note
• “PMB” is not compatible with Macintosh computers.
Recommended computer environment (Windows)
The following computer environment is recommended when using the
supplied software and importing images via a USB connection.
OS (pre-installed)
Microsoft Windows XP*1 SP3/Windows Vista*2 SP2/
Windows 7
“PMB”
CPU: Intel Pentium III 800 MHz or faster
(For playing/editing the High Definition movies: Intel Core
Duo 1.66 GHz or faster/Intel Core 2 Duo 1.66 GHz or faster)
Memory: 512 MB or more (For playing/editing the High
Definition movies: 1 GB or more)
Hard Disk: Disk space required for installation-
approximately 500 MB
Display: Screen resolution-1024 × 768 dots or more
“Image Data
CPU/Memory: Pentium 4 or faster/1 GB or more
Converter SR Ver.3” Display: 1024 × 768 dots or more
“Image Data
Lightbox SR”
*1 64-bit editions and Starter (Edition) are not supported. Windows Image
Mastering API (IMAPI) Ver.2.0 or later is required to use the function
for creating discs.
*2 Starter (Edition) is not supported.
159
Recommended computer environment (Macintosh)
The following computer environment is recommended when using the
supplied software and importing images via a USB connection.
OS (pre-installed)
USB Connection: Mac OS X (v10.3, 10.4, 10.5, 10.6)
“Image Data Converter SR Ver.3”/“Image Data
Lightbox SR”: Mac OS X (v10.4, 10.5, 10.6 (Snow
Leopard))
“Image Data
CPU: Power PC G4/G5 series (1.0 GHz or faster is
Converter SR Ver.3” recommended)/Intel Core Solo/Core Duo/Core 2 Duo or
“Image Data
Lightbox SR”
faster
Memory: 1 GB or more is recommended.
Display: 1024 × 768 dots or more
Notes
• Operation is not assured in an environment based on an upgrade of the operating
systems described above or in a multi-boot environment.
• If you connect two or more USB devices to a single computer at the same time, some
devices, including the camera, may not operate, depending on the types of USB
devices you are using.
• Connecting the camera using a USB interface that is compatible with Hi-Speed USB
(USB 2.0 compliant) allows advanced transfer (high speed transfer), as the camera is
compatible with Hi-Speed USB (USB 2.0 compliant).
• When your computer resumes activity from suspend or sleep mode, communication
between the camera and your computer may not recover at the same time.
160
Using the software
Installing the software (Windows)
Log on as Administrator.
1 Turn on your computer, and insert the CD-ROM (supplied) into
the CD-ROM drive.
The installation menu screen appears.
• If it does not appear, double-click [Computer] (For Windows XP: [My
Computer]) t
(SONYPMB) t [Install.exe].
• If the AutoPlay screen appears, select “Run Install.exe” and follow the
instructions that appear on the screen to proceed with the installation.
2 Click [Install].
Make sure that both “Sony Image Data Suite” and “PMB” are checked and
follow the instructions on the screen.
• Connect the camera to the computer during the procedure following the
instructions on the screen (page 165).
• When the restarting confirmation message appears, restart the computer
following the instructions on the screen.
• DirectX may be installed depending on the system environment of your
computer.
3 Remove the CD-ROM after the installation is complete.
The following software is installed and shortcut icons appear on the desktop.
“Image Data Converter SR”
“Image Data Lightbox SR”
“PMB”
“PMB Launcher”
“PMB Help”
Notes
• If “PMB” has already been installed on the computer, and the version number of the
previously installed “PMB” is lower than that of the “PMB” on the CD-ROM
(supplied), install “PMB” also from the CD-ROM (supplied).
161
• If “PMB” has already been installed on the computer, and the version of the
previously installed “PMB” is higher than that of the “PMB” on the CD-ROM
(supplied), installation is not required. The usable functions are activated when the
camera is connected to the computer using the USB cable.
• If a version of “PMB” under 5.0.00 has been installed on your computer, you may be
unable to use some functions of those “PMB” when installing the “PMB” from the
supplied CD-ROM. Also, “PMB Launcher” is installed from the supplied CD-ROM
and you can start “PMB” or other software by using the “PMB Launcher.” Double-
click the “PMB Launcher” short-cut icon on the computer screen to start “PMB
Launcher.”
Installing the software (Macintosh)
Log on as Administrator.
1 Turn on your Macintosh computer, and insert the CD-ROM
(supplied) into the CD-ROM drive.
2 Double-click the CD-ROM icon.
3 Copy the [IDS_INST.pkg] file in the [MAC] folder to the hard
disk icon.
4 Double-click the [IDS_INST.pkg] file in the copy-to folder.
Follow the instructions on the screen to complete the installation.
Using “Image Data Converter SR”
With “Image Data Converter SR” you can do the following, etc.:
• To edit images recorded in RAW format with various corrections, such as
tone curve, and sharpness.
• To adjust images with white balance, exposure, and creative style, etc.
• To save the images displayed and edited on a computer.
• You can either save the image as RAW format or save it in the general
file format.
162
To use “Image Data Converter SR,” refer to Help.
Click [Start] t [All Programs] t [Sony Image Data Suite] t [Help] t
[Image Data Converter SR Ver.3].
“Image Data Converter SR” support page (English only)
http://www.sony.co.jp/ids-se/
Using “Image Data Lightbox SR”
With “Image Data Lightbox SR” you can do the following, etc.:
• To display and compare RAW/JPEG images recorded with this camera.
• To rate the images on a scale of five.
• To set color labels and so on.
• To display an image with “Image Data Converter SR” and make
adjustments to it.
To use “Image Data Lightbox SR,” refer to Help.
Click [Start] t [All Programs] t [Sony Image Data Suite] t [Help] t
[Image Data Lightbox SR].
“Image Data Lightbox SR” support page (English only)
http://www.sony.co.jp/ids-se/
Using “PMB”
With “PMB” you can do the following, etc.:
• To set images shot with the camera and display them on the computer.
• To organize images on the computer on a calendar by shooting date to
view them.
• To retouch (red-eye reduction, etc.), print, and send still images as e-mail
attachments, change the shooting date.
• To display the shooting location of the image on the map (SLT-A55V
only).
• To print or save still images with the date.
• To create a data disc using a CD burner drive or DVD burner drive.
• To create Blu-ray discs, AVCHD format discs or DVD discs from
AVCHD format movies imported to a computer. (An internet connection
163
environment is required when a Blu-ray disc/DVD disc is created for the
first time.)
Notes
• “PMB” is not compatible with Macintosh computers.
• The confirmation message of the Information tool appears on the screen when
starting “PMB” for the first time. Select [Start]. This function informs you of news,
such as software updates. You can change the setting later.
To use “PMB,” refer to “PMB Help.”
Double-click the shortcut of
(PMB Help) on the desktop. Or, click
[Start] t [All Programs] t [PMB] t [PMB Help].
“PMB” support page (English only)
http://www.sony.co.jp/pmb-se/
164
Connecting the camera to the computer
1 Insert a sufficiently charged battery pack into the camera, or
connect the camera to a wall outlet (wall socket) using the AC-
PW20 AC Adaptor (sold separately).
2 Turn on the computer, then press the
(Playback) button.
3 Check that [USB Connection] in
2 is set to [Mass Storage].
4 Connect the camera to your
computer.
1 To a USB terminal of the
computer
• When a USB connection is established
for the first time, your computer
automatically runs a program to
recognize the camera. Wait for a while.
USB cable (supplied)
2 To the USB terminal
Importing images to the computer (Windows)
“PMB” allows you to easily import images.
For details on “PMB” functions, see the “PMB Help.”
Importing images to the computer without using “PMB”
When the AutoPlay Wizard appears after making a USB connection
between the camera and a computer, click [Open folder to view files] t
[OK] t [DCIM] or [MP_ROOT] t copy the desired images to the
computer.
165
File name
Folder
The type of file
File name
DCIM folder
JPEG file
DSC0ssss.JPG
_DSCssss.JPG
DSC0ssss.ARW
_DSCssss.ARW
MAH0ssss.MP4
MAQ0ssss.MP4
JPEG file (Adobe RGB)
RAW file
RAW file (Adobe RGB)
MP4 file (1440 × 1080)
MP4 file (VGA)
MP_ROOT folder
• ssss (file number) stands for any number within the range of 0001 to
9999.
• When [Image: Quality] is set to [RAW & JPEG], the numerical portions
of the name of a RAW data file and its corresponding JPEG file are the
same.
Notes
• For operations such as importing AVCHD movies to the computer, use “PMB.”
• Use “PMB” to import the movies with GPS location information to a computer
(SLT-A55V only).
• When the camera is connected to the computer, if you operate AVCHD format
movies or folders from the connected computer, images may be damaged or cannot
be played. Do not delete or copy AVCHD format movies on the memory card from
the computer. Sony is not held liable for consequences resulting from such
operations via the computer.
Importing images to the computer (Macintosh)
1 Connect the camera to your Macintosh computer first. Double-
click the newly recognized icon on the desktop t the folder
where the images you want to import are stored.
2 Drag and drop the image files to the hard disk icon.
The image files are copied to the hard disk.
166
3 Double-click the hard disk icon t the desired image file in the
folder containing the copied files.
The image is displayed.
Note
• Use “iMovie” bundled with a Macintosh computer to import or operate AVCHD
format movies.
Deleting the USB connection
Perform the procedures from step 1 to 3 below before:
• Disconnecting the USB cable.
• Removing the memory card.
• Turning off the camera.
1 Double-click the disconnect icon
Windows Vista
on the tasktray.
Windows XP
Disconnect icon
2 Click (USB Mass Storage Device) t [Stop].
3 Confirm the device on the confirmation window, then click
[OK].
Note
• Drag and drop the icon of the memory card or the drive icon to the “Trash” icon
beforehand when you use a Macintosh computer, and the camera is disconnected
from the computer.
167
Creating a movie disc
You can create a disc from AVCHD format movies recorded on the
camera.
Selecting the method for creating a disc
Select the method that best suits your disc player.
See “PMB Help” for details on creating a disc using “PMB.”
To import movies, see page 165.
Player
Method
Disc type
Create a Blu-ray disc of movies
and photos imported to a
computer using “PMB.”
Blu-ray disc playback devices
(Blu-ray disc player,
PlayStation®3, etc.)
AVCHD format playback devices Create an AVCHD format disc of
(Sony Blu-ray disc player,
PlayStation®3, etc.)
movies and photos imported to a
computer using “PMB.”
Creating an AVCHD format disc
with a DVD writer/recorder other
than DVDirect Express.
Ordinary DVD playback devices Create a standard definition
(DVD player, DVD playable
computer, etc.)
image quality (STD) disc of
movies and photos imported to a
computer using “PMB.”
Notes
• If you use a Sony DVDirect (DVD Writer), you can transfer data by inserting a
memory card into the memory card slot of the DVD writer, or connecting your
camera to the DVD writer with a USB cable.
• When you use Sony DVDirect (DVD writer), make sure that the version of DVD
writer’s firmware is the latest.
For details, refer to the following URL:
http://sony.storagesupport.com/
168
Characteristics of each type of disc
A Blu-ray disc enables you to record high definition image quality
(HD) movies of a longer duration than DVD discs.
High definition image quality (HD) movie can be recorded on DVD
media, such as DVD-R discs, and a high definition image quality
(HD) disc is created.
• You can play a high definition image quality (HD) disc on AVCHD
format playback devices, such as a Sony Blu-ray disc player and a
PlayStation®3. You cannot play the disc on ordinary DVD players.
Standard definition image quality (STD) movie converted from high
definition image quality (HD) movie can be recorded on DVD media,
such as DVD-R discs, and a standard image quality (STD) disc is
created.
Discs you can use with “PMB”
You can use 12 cm discs of following type with “PMB.” For Blu-ray disc,
Disc type
Features
DVD-R/DVD+R/DVD+R DL
DVD-RW/DVD+RW
Unrewritable
Rewritable
• Always maintain your PlayStation®3 to use the latest version of the
PlayStation®3 system software.
• The PlayStation®3 may not be available in some countries/regions.
Creating an AVCHD format disc
You can create a high definition image quality (HD) AVCHD format disc
from AVCHD format movies imported to a computer using the supplied
software “PMB.”
1 Select the AVCHD format movies you want to write on “PMB.”
2 Click
(HD)].
(Create Discs) to select [Create AVCHD Format Discs
The screen used for creating a disc appears.
• For details, see “PMB Help.”
169
Notes
• Install “PMB” beforehand.
• Still images and MP4 movie files cannot be recorded on the AVCHD format disc.
• It may take a long time to create a disc.
Playing AVCHD format disc on a computer
You can play back AVCHD format discs using “Player for AVCHD” that
is installed together with “PMB.”
To start the software, click on [Start] t [All Programs] t [PMB] t
[PMB Launcher] t [View] t [Player for AVCHD].
For detailed operations, see the Help for “Player for AVCHD.”
Note
• Movies may not be played smoothly depending on the computer environment.
Creating a Blu-ray disc
You can create a Blu-ray disc with AVCHD movies previously imported to
a computer. Your computer must support the creation of Blu-ray discs.
BD-R (non-rewritable) and BD-RE (rewritable) media can be used to create
Blu-ray discs. You cannot add contents to either type of disc once it has
been created.
Click [BD Add-on Software] on the installation screen of “PMB,” and
install this plug-in according to the on-screen instructions.
Connect your computer to the Internet when you install [BD Add-on
Software].
See “PMB Help” for details.
170
Creating a standard definition image quality (STD) disc
You can create a standard definition image quality (STD) disc from
AVCHD format movies imported to a computer using supplied software
“PMB.”
1 Select the AVCHD format movies you want to write on “PMB.”
2 Click
(Create Discs) to select [Create DVD-Video Format
Discs (STD)].
The screen used for creating a disc appears.
• For details, see “PMB Help.”
Notes
• Install “PMB” beforehand.
• MP4 movie files cannot be recorded on a disc.
• It will take a longer time to create a disc because AVCHD format movies are
converted to standard definition image quality (STD) movies.
• An Internet connection environment is required when creating a DVD-Video (STD)
disc for the first time.
171
Printing images
Specifying DPOF
Using the camera, you can specify the still images and the number of
images to print before you print images at a shop or with your printer.
Follow the procedure below.
DPOF specifications are left with images after printing. It is recommended
that you unspecify them after printing.
Specifying /unspecifying DPOF on selected images
1 MENU button t
1 t [Specify Printing] t [DPOF Setup]
t [Multiple Img.]
2 Select the image with b/B on the control button.
3 Select the number of sheets with the center of the control
button.
• To unspecify DPOF, set the number to “0.”
4 Press the MENU button.
5 Select [Enter] with v, then press the center of the control
button.
Notes
• You cannot specify DPOF on RAW data files.
• You can specify any number up to 9.
172
Others
image sensor-shift
mechanism
Specifications
[Auto focus system]
Camera
System
TTL phase-detection
system, 15 points (3 points
cross type)
[System]
Camera Type
Sensitivity Range
–1 to 18 EV (at ISO 100
equivalent)
Interchangeable Lens
Digital Camera
Lens
A-mount lens
AF illuminator
Approx. 1 to 5 m (3.3 to
16.4 feet)
[Image sensor]
Image format
SLT-A55/A55V
[Live View]
Type
23.5×15.6 mm (APS-C
format) CMOS image
sensor
Main sensor Live View
(Translucent mirror
mechanism)
SLT-A33
Image format
23.4×15.6 mm (APS-C
format) CMOS image
sensor
“Exmor” CMOS sensor
Frame coverage
100%
Total pixel number of image sensor
SLT-A55/A55V
[Electronic viewfinder]
Type Electronic viewfinder
(color)
Approx. 16 700 000 pixels
SLT-A33
Approx. 14 600 000 pixels
Screen size 1.2 cm (0.46 type)
Effective pixel number of camera
SLT-A55/A55V
Total number of dots
Approx. 16 200 000 pixels
SLT-A33
Approx. 14 200 000 pixels
1 440 000 dots conversion
Available screen size displayed
1.1 cm (0.43 type)
[SteadyShot]
Available number of dots displayed
1 152 000 dots conversion
System
Image sensor-shift
mechanism
Frame coverage
100%
Effect
Approx. 2.5 to 4 EV in
shutter speed (depending
on shooting conditions and
the attached lens)
Magnification
1.10 × with 50 mm lens at
infinity, –1 m–1 (diopter)
Eye Relief Approximately 19 mm
from the eyepiece, 18 mm
from the eyepiece frame at
–1 m–1
[Anti-Dust]
System
Charge protection coating
on Low-Pass Filter and
174
Dioptor Adjustment
–4.0 to +4.0 m–1 (diopter)
Flash coverage
Covering 18 mm lens
(focal length that the lens
indicates)
[LCD monitor]
LCD panel 7.5 cm (3.0 type) TFT
drive
Flash compensation
2.0 EV (1/3 EV step)
Total number of dots
921 600 (640 × 3 (RGB) ×
480) dots
[Recording format]
File format JPEG (DCF Ver. 2.0, Exif
Ver. 2.3, MPF Baseline)
compliant, DPOF
[Exposure control]
compatible
Metering Cell
“Exmor” CMOS sensor
Movie (AVCHD format)
AVCHD Ver. 1.0
compliant
Metering method
1200-zone evaluative
metering
Video: MPEG-4 AVC/
H.264
Audio: Dolby Digital 2ch,
equipped with Dolby
Digital Stereo Creator
Metering Range
–2 to +17 EV on Multi
segment, Center weighted,
Spot modes (at ISO 100
equivalent with F1.4 lens)
• Manufactured under
license from Dolby
Laboratories.
ISO sensitivity (Recommended
exposure index)
Movie (MP4 format)
Video: MPEG-4 AVC/
H.264
AUTO, ISO 100 to 12800
Exposure compensation
2.0 EV (1/3 EV step)
Audio: MPEG-4 AAC-LC
2ch
[Shutter]
Type
Electronically-controlled,
vertical-traverse, focal-
plane type
[Recording media]
“Memory Stick PRO Duo”
media, SD card
Speed range 1/4000 second to 30
seconds, bulb, (1/3 EV
step)
[Input/output terminals]
USB
miniB
Flash sync speed
1/160 second
HDMI
HDMI type C minijack
Mic Terminal
3.5 mm Stereo minijack
[Built-In-Flash]
REMOTE Terminal
Flash G.No.
GN 10 (in meters at ISO
100)
[Power, general]
Used battery pack
Recycling time
Rechargeable battery pack
NP-FW50
Approx. 4 seconds
175
[Others]
Exif Print Compatible
Rechargeable battery pack
NP-FW50
PRINT Image Matching III
Compatible
Used battery
Lithium-ion battery
Dimensions Approx. 124.4 × 92 ×
84.7 mm (4 7/8 × 3 5/8 ×
3 1/3 inches) (W/H/D,
Maximum voltage
DC 8.4 V
Nominal voltage
DC 7.2 V
excluding protrusions)
Mass
SLT-A55V
Maximum charge voltage
DC 8.4 V
Approx. 500 g (1 lb 1.6 oz)
(with battery and “Memory
Stick PRO Duo” media)
Approx. 441 g (15.6 oz)
(body only)
Maximum charge current
1.02 A
Capacity
SLT-A55/A33
Typical 7.7 Wh (1 080 mAh)
Minimum 7.3 Wh (1 020 mAh)
Approx. 492 g (1 lb 1.3 oz)
(with battery and “Memory
Stick PRO Duo” media)
Approx. 433 g (15.3 oz)
(body only)
Maximum dimensions
Approx. 31.8 × 18.5 × 45
mm (1 5/16 × 3/4 × 1 13/16
inches) (W/H/D)
Operating temperature
0 to 40°C (32 to 104°F)
Mass
Approx. 57 g (2.1 oz)
USB communication
Hi-Speed USB (USB 2.0
Design and specifications are subject
to change without notice.
compliant)
BC-VW1 Battery charger
Input rating 100 V - 240 V AC, 50 Hz/
60 Hz, 4.2 W
On focal length
The picture angle of this camera is
narrower than that of a 35 mm-format
film camera. You can find the
approximate equivalent of the focal
length of a 35 mm-format film
camera, and shoot with the same
picture angle, by increasing the focal
length of your lens by half.
For example, by using a 50 mm lens,
you can get the approximate
equivalent of a 75 mm lens of a 35
mm-format film camera.
Output rating
8.4 V DC, 0.28 A
Operating temperature range
0 to 40°C (32 to 104°F)
Storage temperature range
–20 to +60°C (–4 to
+140°F)
Maximum dimensions
Approx. 63 × 95 × 32 mm
(2 1/2 × 3 3/4 × 1 5/16
inches) (W/H/D)
Mass
Approx. 85 g (3 oz)
176
On image data compatibility
• This camera conforms with DCF
(Design rule for Camera File
system) universal standard
established by JEITA (Japan
Electronics and Information
Technology Industries
Trademarks
is a trademark of Sony
Corporation.
•
• “Memory Stick,”
Stick PRO,”
, “Memory
,
“Memory Stick Duo,”
, “Memory Stick
,
Association).
PRO Duo,”
• Playback of images recorded with
your camera on other equipment
and playback of images recorded or
edited with other equipment on
your camera are not guaranteed.
“Memory Stick PRO-HG Duo,”
, “Memory
Stick Micro,” “MagicGate,” and
are trademarks of
Sony Corporation.
• “InfoLITHIUM” is a trademark of
Sony Corporation.
• “PhotoTV HD” is a trademark of
Sony Corporation.
• “AVCHD” and “AVCHD”
logotype are trademarks of
Panasonic Corporation and Sony
Corporation.
• “Blu-ray Disc” and the logo are
trademarks.
• Dolby and the double-D symbol are
trademarks of Dolby Laboratories.
• Microsoft, Windows, DirectX, and
Windows Vista are either registered
trademarks or trademarks of
Microsoft Corporation in the
United States and/or other
countries.
• HDMI, the HDMI logo and High-
Definition Multimedia Interface are
trademarks or registered trademarks
of HDMI Licensing LLC.
• Macintosh and Mac OS are
trademarks or registered trademarks
of Apple Inc.
• PowerPC is a registered trademark
of IBM Corporation in the United
States.
177
• Intel, Intel Core, MMX, and
Pentium are trademarks or
registered trademarks of Intel
Corporation.
• SDXC, SDHC Logo are trademarks
of SD-3C, LLC.
• Eye-Fi is a trademark of Eye-Fi Inc.
• MultiMediaCard is a trademark of
MultiMediaCard Association.
• “PlayStation” is a registered
trademark of Sony Computer
Entertainment Inc.
• Adobe is a registered trademark or
a trademark of Adobe Systems
Incorporated in the United States
and/or other countries.
• In addition, system and product
names used in this manual are, in
general, trademarks or registered
trademarks of their respective
developers or manufacturers.
However, the ™ or ® marks are not
used in all cases in this manual.
178
Troubleshooting
If you experience trouble with your camera, try the following solutions.
authorized Sony service facility.
1
Check the following items.
2
Remove the battery pack, and insert the battery pack again after
about one minute, and turn on the power.
3
Reset the settings (page 156).
4
Consult your Sony dealer or local authorized Sony service facility.
Battery pack and power
The battery pack cannot be installed.
• As you insert the battery pack, use the tip of the battery pack to push the
• You can use an NP-FW50 battery pack only. Make sure that the battery is
NP-FW50.
The remaining battery indicator is incorrect, or sufficient remaining
battery indicator is displayed but the power runs out too quickly.
• This phenomenon occurs when you use the camera in an extremely hot or
Cannot turn on the camera.
179
The power turns off suddenly.
• If you do not operate the camera for given period of time, the camera turns
to power saving mode and nearly shuts down. To cancel the power save,
operate the camera, such as pressing the shutter button halfway down
The CHARGE lamp flashes when charging the battery pack.
• You can use an NP-FW50 battery pack only. Make sure that the battery is
NP-FW50.
• If you charge a battery pack that has not been used for a long time, the
CHARGE lamp may flash.
• The CHARGE lamp flashes in two ways, fast (about 0.15-second intervals)
and slow (about 1.5-second intervals). If it is flashing fast, remove the
battery pack and reattach the same battery pack securely. If the CHARGE
lamp flashes fast again, it suggests that there is something wrong with the
battery pack. Slow flashing indicates that charging is suspended because the
ambient temperature is outside the suitable range for charging the battery
pack. Charging will resume and the CHARGE lamp will be lit when the
ambient temperature returns to within the suitable temperature.
Charge the battery pack under the suitable temperatures between 10°C and
30°C (50°F and 86°F).
Shooting images
Nothing is displayed on the LCD monitor in viewfinder mode when the
power is turned on.
• If you do not operate the camera for given period of time, the camera turns
to power saving mode and nearly shuts down. To cancel the power save,
operate the camera, such as pressing the shutter button halfway down
The image is not clear in the viewfinder.
• Adjust the diopter scale properly using the diopter-adjustment dial
No images in the viewfinder.
• [FINDER/LCD Setting] is set to [Manual]. Press the FINDER/LCD button
180
The shutter does not release.
• You are using a memory card with a write-protect switch, and the switch is
set to the LOCK position. Set the switch to the recording position.
• The shutter cannot be released when the subject is out of focus.
• When the camera is attached to another device, such as an astronomical
Recording takes a long time.
malfunction.
large, the RAW mode shooting may take time.
The same image is shot several times.
• The drive mode is set to [Continuous adv.] or [Bracket: Cont.]. Set it to
• The exposure mode is set to AUTO+ and [Auto+ Image Extract.] is set to
The image is out of focus.
• The subject is too close. Check the minimum focal distance of the lens.
• You are shooting in manual focus mode, set the focus mode switch to AF
• When the focus mode switch is equipped with the lens, set it to AF.
• Ambient light is insufficient.
Eye-Start AF does not work.
• Press the shutter button halfway down.
181
The flash does not work.
• The flash mode is set to [Autoflash]. If you want to make sure the flash fires
The flash takes too long to recharge.
• The flash has been fired in succession in a short period. When the flash has
been fired in succession, the recharging process may take longer than usual
to avoid overheating of the camera.
A picture taken with the flash is too dark.
• If the subject is beyond the flash range (the distance that the flash can
reach), the pictures will be dark because the flash light does not reach the
subject. If the ISO is changed, the flash range also changes with it
The date and time are recorded incorrectly.
• The area selected with [Area Setting] is different from the actual area. Set
The aperture value and/or shutter speed flashes when you press the
shutter button halfway down.
• Since the subject is too bright or too dark, it is beyond the available range of
the camera. Adjust the setting again.
The image is whitish (Flare).
Blurring of light appears on the image (Ghosting).
• The picture was taken under a strong light source, and excessive light has
entered the lens. Attach a lens hood (sold separately).
The corners of the picture are too dark.
• If any filter or hood is used, take it off and try shooting again. Depending on
the thickness of the filter and improper attachment of the hood, the filter or
the hood may partially appear in the image. The optical properties of some
lenses may cause the periphery of the image to appear too dark (insufficient
light).
182
The eyes of the subject come out red.
• Get close to the subject, and shoot the subject within the flash range using
Dots appear and remain on the LCD monitor.
The image is blurred.
• The picture was taken in a dark location without the flash, resulting in
96).
The EV scale b B is flashing on the LCD monitor or in the viewfinder.
• The subject is too bright or too dark for the metering range of the camera.
Viewing images
Your camera cannot play back images.
• When an image file has been processed by a computer or when the image
file was recorded using a model other than that of your camera, playback on
your camera is not guaranteed.
• Use “PMB” to play images stored on a PC with this camera.
Deleting/Editing images
Your camera cannot delete an image.
• Cancel the protection (page 131).
You have deleted an image by mistake.
• Once you have deleted an image, you cannot restore it. We recommend that
You cannot mark a DPOF mark.
• You cannot mark DPOF marks on RAW images.
183
GPS (SLT-A55V only)
The camera is not receiving a GPS signal.
• Set [GPS On/Off] to [On] (page 138).
• Your camera may not be able to receive radio signals from GPS satellites
because of obstructions.
• To triangulate the location information correctly, bring your camera to an
open area, and turn on the camera again.
Excessive error in location information.
• The margin of error can be up to several-hundred meters depending on
surrounding buildings, weak GPS signals, etc.
• Your camera cannot receive a GPS signal. Previously-triangulated location
information may be used in the present location instead. Check the
triangulation status with the GPS indicator displayed on the screen during
shooting (page 138).
It takes time to triangulate although GPS assist data has been taken in.
• [Date/Time Setup] is not set, or set time is shifted greatly. Set the date and
• The term of validity of assist data has expired. Update the GPS assist data
• As the positions of GPS satellites vary constantly, it may take longer to
determine the location or the receiver may not be able to determine the
location at all, depending on the location and time you use the camera.
• “GPS” is a system for determining geographic location by triangulating
radio signals from GPS satellites. Avoid using the camera in places where
radio signals are blocked or reflected, such as a shadowy place surrounded
by buildings or trees, etc. Use the camera in open sky environments.
The location information has not been recorded.
• Use “PMB” to import the movies with GPS location information to your
computer.
Computers
You do not know if the OS of your computer is compatible with the
camera.
184
Your computer does not recognize your camera.
• Check that the camera is turned on.
use the AC Adaptor (sold separately).
• Disconnect the USB cable, and connect it again firmly.
• Disconnect all equipment other than the camera, the keyboard and the
mouse from the USB jacks of your computer.
• Connect the camera directly to your computer without passing through a
USB hub or other device (page 165).
You cannot copy images.
• Make the USB connection by properly connecting the camera with your
computer (page 165).
• When you shoot images with a memory card formatted by a computer, you
may not be able to copy the images to a computer. Shoot using a memory
card formatted by your camera (page 146).
The image cannot be played back on a computer.
• If you are using “PMB,” refer to the “PMB Help.”
• Consult the computer or software manufacturer.
After making a USB connection, “PMB” does not start automatically.
Memory card
Cannot insert a memory card.
• Insertion direction of the memory card is wrong. Insert it in the correct
Cannot record on a memory card.
185
You have formatted a memory card by mistake.
• All the data on the memory card are deleted by formatting. You cannot
restore it.
Printing
Cannot print images.
• RAW images cannot be printed. To print RAW images first, convert them
to JPEG images using “Image Data Converter SR” on the supplied CD-
ROM.
The color of the image is strange.
• When you print the images recorded in Adobe RGB mode using sRGB
printers that are not compatible with Adobe RGB (DCF2.0/Exif2.21), the
Images are printed with both edges cut off.
• Depending on your printer, the left, right, top, and bottom edges of the
image may be cut off. Especially when you print an image shot with the
aspect ratio set to [16:9], the lateral end of the image may be cut off.
• When printing images using your own printer, cancel the trimming or
borderless settings. Consult the printer manufacturer as to whether the
printer provides these functions or not.
• When having images printed at a digital print shop, ask the shop whether
they can print the images without cutting off both edges.
Cannot print images with the date.
• This camera does not have a feature for superimposing dates on images.
However, because the images shot with the camera include information on
the recording date, you can print images with the date superimposed if the
printer or the software can recognize Exif information. For compatibility
with Exif information, consult the manufacturer of the printer or the
software.
• When you print images at a shop, images can be printed with the date if you
ask them to do so.
186
Others
The lens gets fogged.
• Moisture condensation has occurred. Turn off the camera and leave it for
The message “Set Area/Date/Time.” appears when you turn on the
camera.
• The camera has been left unused for sometime with a low battery or no
If the date setting is lost every time the battery pack is charged, consult your
Sony dealer or local authorized Sony service facility.
The number of recordable images does not decrease or decreases two at
a time.
• This is because the compression rate and the image size after compression
The setting is reset without the resetting operation.
• The battery pack was removed when the power switch was set to ON. When
removing the battery pack, make sure the camera is turned off and the
The camera does not work properly.
• Turn off the camera. Remove the battery pack and insert it again. If the
camera is hot, remove the battery pack, and allow it to cool down before
trying this corrective procedure.
• If an AC Adaptor (sold separately) is used, disconnect the power plug.
Connect the power plug and turn on the camera again. If the camera does
not work after doing these solutions, consult your Sony dealer or local
authorized Sony service facility.
The five bars of the SteadyShot scale flashes.
• The SteadyShot function does not work. You can continue to shoot but the
SteadyShot function will not work. Turn the camera off and on. If the
SteadyShot scale continues to flash, consult your Sony dealer or local
authorized Sony service facility.
187
Warning messages
Memory Card Error
• An incompatible memory card is
inserted or the format has failed.
If the following messages appear,
follow the instructions below.
Reinsert memory card.
Incompatible battery. Use correct
model.
• An incompatible battery pack is
being used.
• The inserted memory card
cannot be used in your camera.
• The memory card is damaged.
• The terminal section of the
memory card is dirty.
Set Area/Date/Time.
Memory card locked.
• Set the area and date, time. If
you have not used the camera for
a long time, charge the internal
192).
• You are using a memory card
with a write-protect switch, and
the switch is set to the LOCK
position. Set the switch to the
recording position.
Power insufficient.
This memory card may not be
capable of recording and playing
normally.
• The inserted memory card
cannot be used with the camera.
• You tried to perform [Cleaning
Mode] when the battery level is
insufficient. Charge the battery
pack or use the AC Adaptor
(sold separately).
Processing...
Unable to use memory card.
Format?
• When Long exposure noise
reduction will be done for the
same amount of time that the
shutter was open. You cannot do
any further shooting during this
reduction.
•
The memory card was formatted
on a computer and the file format
was modified.
Select [Enter], then format the
memory card. You can use the
memory card again, however, all
previous data in the memory card
is erased. It may take a some time
to complete the format.
Unable to display.
• Images recorded with other
cameras or images modified with
a computer may not be able to be
displayed.
If the message still appears,
change the memory card.
189
Check the lens attachment. If the
lens is not supported, you can
permit use of the lens in the
custom menu.
• The lens is not attached properly,
or the lens is not attached.
• Because you have been
recording for a long time, the
temperature inside the camera
has increased to an unacceptable
level. Stop recording.
• When attaching the camera to an
astronomical telescope or
something similar, set [Release
w/oLens] to [Enable].
Recording is unavailable in this
movie format.
• Set [Movie: File Format] to
[MP4].
Contains no still images.
Contains no movies.
• The number of images exceeds
that for which date management
in a database file by the camera
is possible.
• There is no image in the memory
card.
Image protected.
• You tried to delete protected
images.
• Unable to register to the database
file. Import all the images to a
computer using “PMB” and
recover the memory card.
Unable to print.
• You tried to mark RAW images
with a DPOF mark.
Camera Error
System Error
Camera overheating. Allow it to
cool.
• Turn the power off, remove the
battery pack, then re-insert it. If
the message appears frequently,
consult your Sony dealer or local
authorized Sony service facility.
• The camera has become hot
because you have been shooting
continuously.
Turn the power off. Cool the
camera and wait until the camera
is ready to shoot again.
Image Database File error.
Reboot.
• There is something wrong
occurred in the Image Database
File. Execute [Recover Image
190
Image Database File error.
Recover?
• You cannot record or play back
AVCHD format movies because
the Image Database File is
damaged. Follow the on-screen
instructions to recover data.
Unable to magnify.
Unable to rotate image.
• Images recorded with other cameras
may not be enlarged or rotated.
No images changed
• You attempted to specified
DPOF without specifying
images.
Cannot create more folders.
• The folder with a name beginning
with “999” exists on the memory
card. You cannot create any
folders if this is the case.
191
On operating temperatures
Precautions
Your camera is designed for use
under the temperatures between 0 and
40°C (32 and 104°F). Shooting in
extremely cold or hot places that
exceed this range is not
Do not use/store the camera in
the following places
• In an extremely hot, dry or humid
place
recommended.
In places such as in a car parked in
the sun, the camera body may
become deformed and this may
cause a malfunction.
• Storing under direct sunlight or
near a heater
The camera body may become
discolored or deformed, and this
may cause a malfunction.
• In a location subject to rocking
vibration
• Near strong magnetic place
• In sandy or dusty places
Be careful not to let sand or dust get
into the camera. This may cause the
camera to malfunction, and in some
cases this malfunction cannot be
repaired.
On moisture condensation
If the camera is brought directly from
a cold to a warm location, moisture
may condense inside or outside the
camera. This moisture condensation
may cause a malfunction of the
camera.
How to prevent moisture
condensation
When bringing the camera from a
cold place to a warm place, seal the
camera in a plastic bag and allow it to
adapt to conditions at the new
location over about an hour.
If moisture condensation occurs
Turn off the camera and wait about an
hour for the moisture to evaporate.
Note that if you attempt to shoot with
moisture remaining inside the lens,
you will be unable to record clear
images.
On storing
Be sure to attach the lens cap or
body cap when not using the
camera. When attaching the body
cap, remove all the dust from the
cap before placing it on the camera.
When you purchase the DT 18 – 55
mm F3.5 – 5.6 SAM Lens Kit,
purchase the Rear Lens Cap ALC-
R55 also.
On the internal rechargeable
battery
This camera has an internal
rechargeable battery for maintaining
the date and time and other settings
regardless of whether the power is on
or off, or the battery pack is charged
or discharged.
192
This rechargeable battery is
before shooting. Note that
formatting permanently erases all
data on the memory card, and is
unrecoverable. Save precious data
on a computer, etc.
• If you repeatedly record/delete
images, fragmentation of data may
occur on the memory card. Movies
may not be able to be saved or
recorded. In such a case, save your
images to a computer or other
storage location, then format the
memory card (page 146).
continually charged as long as you
are using the camera. However, if you
use the camera for only short periods,
it discharges gradually, and if you do
not use the camera at all for about 3
months it becomes completely
discharged. In this case, be sure to
charge this rechargeable battery
before using the camera.
However, even if this rechargeable
battery is not charged, you can still
use the camera as long as you do not
record the date and time. If the
camera resets the settings to the
defaults each time you charge the
battery, the internal rechargeable
battery may be dead. Consult your
Sony dealer or local authorized Sony
service facility.
• Before you record one-time events,
make a trial recording to make sure
that the camera is working
correctly.
• This camera is neither dust-proof,
nor splash-proof, nor water-proof.
• Do not look at the sun or a strong
light through a removed lens or the
viewfinder. This may cause
irrecoverable damage to your eyes.
Or it may cause a malfunction of
your camera.
• Do not use the camera near a
location that generates strong radio
waves or emits radiation. The
camera may not be able to record or
play back properly.
• Using the camera in sandy or dusty
locations may cause malfunctions.
• If moisture condensation occurs,
remove it before using the camera
Charging method of the internal
rechargeable battery
Insert a charged battery pack in the
camera, or connect the camera to a
wall outlet (wall socket) using the AC
Adaptor (sold separately), and leave
the camera for 24 hours or more with
the power off.
On memory cards
Do not attach a label, etc. on a
memory card or a card adaptor. This
may cause a malfunction.
• Do not shake or strike the camera.
In addition to malfunctions and an
inability to record images, this may
render the memory card unusable,
or cause image data breakdown,
damage or loss.
Notes on recording/playback
• When you use a memory card with
this camera for the first time, it is
recommended to format the card
using the camera for stable
performance of the memory card
193
• Clean the flash surface before use.
The heat of flash emission may
cause dirt on the flash surface to
become discolored or to stick to the
flash surface, resulting in
insufficient light emission.
• Keep the camera, supplied
accessories, etc., out of the reach of
children. A memory card, etc., may
be swallowed. If such a problem
occurs, consult a doctor
immediately.
194
Recording media: Memory card
AVCHD format
*1 1080i specification
A high definition specification which
utilizes 1,080 effective scanning lines
and the interlace system.
The AVCHD format is a high
definition digital video camera format
used to record a high definition (HD)
signal of either the 1080i
*2 720p specification
specification*1 or the 720p
A high definition specification which
utilizes 720 effective scanning lines
and the progressive system.
*3 Data recorded in AVCHD format
other than the above mentioned
cannot be played on your camera.
specification*2 using efficient data
compression coding technology. The
MPEG-4 AVC/H.264 format is
adopted to compress video data, and
the Dolby Digital or Linear PCM
system is used to compress audio
data.
The MPEG-4 AVC/H.264 format is
capable of compressing images at
higher efficiency than that of the
conventional image compressing
format. The MPEG-4 AVC/H.264
format enables a high definition video
signal shot on a digital video camera
recorder to be recorded on 8 cm DVD
discs, hard disk drive, flash memory,
memory card, etc.
Recording and playback on
your camera
Based on the AVCHD format, your
camera records with the high
definition image quality (HD)
mentioned below.
Video signal*3:
1080 60i-compatible device
MPEG-4 AVC/H.264 1920 ×
1080/60i
1080 50i-compatible device
MPEG-4 AVC/H.264 1920 ×
1080/50i
Audio signal: Dolby Digital 2ch
195
from the GPS satellites do not reach
the camera as follows.
– In tunnels, indoors or under the
shade of buildings.
GPS (SLT-A55V
only)
– Between tall buildings or at
narrow streets surrounded by
buildings.
– In underground locations,
locations surrounded by dense
trees, under an elevated bridge, or
in locations where magnetic fields
are generated, such as near high
voltage cables.
– Near devices that generate radio
signals of the same frequency
band as the camera: near 1.5 GHz
band mobile telephones, etc.
This system allows you to pinpoint
your exact location on the earth. The
GPS satellites are located in 6 orbits,
20,000 km above the earth. The GPS
system consists of 24 or more GPS
satellites. A GPS receiver receives
radio signals from the satellites, and
calculates the current location of the
receiver based on the orbital
information (almanac data) and travel
time of the signals, etc.
Determining a location is called
“triangulating.” A GPS receiver can
determine the location’s latitude and
longitude by receiving signals from 3
or more satellites.
• As the positions of GPS satellites
vary constantly, it may take longer
to determine the location or the
receiver may not be able to
On triangulating errors
• If you move to another location
right after turning on the camera, it
may take a longer time for the
camera to start triangulating,
compared to when you stay in the
same place.
determine the location at all,
depending on the location and time
you use the camera.
• “GPS” is a system for determining
geographic location by
triangulating radio signals from
GPS satellites. Avoid using the
camera in places where radio
signals are blocked or reflected,
such as a shadowy place
surrounded by buildings or trees,
etc. Use the camera in open sky
environments.
• If triangulating fails, previously-
triangulated location information
may be written onto the image in
the camera.
• Error caused by the position of GPS
satellites
The camera automatically
triangulates your current location
when the camera receives radio
signals from 3 or more GPS
satellites. The triangulating error
allowed by the GPS satellites is
about 30 m (98 feet). Depending on
the environment of the location, the
triangulating error can be greater. In
this case, your actual location may
• You may not be able to record
location information at locations or
in situations where radio signals
196
not match the location on the map
based on the GPS information.
Meanwhile, the GPS satellites are
controlled by the United States
Department of Defense, and the
degree of accuracy may be changed
intentionally.
• Error during the triangulating
process
The camera acquires location
information every about 15 seconds
during triangulating. There is a
slight time difference between
when the location information is
acquired and when the location
information is recorded on an
image, therefore, the actual
recording location may not match
exactly the location on the map
based on the GPS information.
On the restriction of use of
GPS on an airplane
During take off and landing of an
airplane, turn off the camera, as you
will be instructed to do by the on-
board announcement.
On the other restriction
Use GPS in accordance with the
regulations of the place or situation.
On the geographic coordinate
system
The “WGS-84” geographic
coordinate system is used.
197
change the lock angle and shoot
again.
• The available shooting direction is
horizontal only.
• For details on the procedure used
for shooting 3D-images, see page
68.
3D-shootings
Notes on recording
• [3D Panorama] is not suitable when
shooting:
– Subjects are moving.
– Subjects are too close to the
camera.
– Subjects with a repeating pattern
such as tiles, and subjects with
little contrast such as sky, sandy
beach, or lawn.
• [3D Panorama] recording may be
discontinued in the following
situations:
Note on playback of 3D-
images
When you play back 3D-images on
the LCD monitor of the camera or on
a non-3D-compatible TV, the images
are played back without the 3D
effect.
– You pan or tilt the camera too fast
or too slow.
Notes on 3D-image files
• A JPEG file and an MPO are
combined to create a 3D-image. If
you erase one of these files from the
computer, the 3D-image may not be
played back properly.
• For details on the procedure used
for viewing 3D-images, see pages
– There is too much camera shake.
• If you cannot pan or tilt the camera
across the entire subject within the
given time, a black area occurs in
the composed image. If this
happens, move the camera fast to
record a full panoramic image.
• Since several images are stitched
together, the stitched part will not
be recorded smoothly.
• Under low light conditions, images
may be blurred.
• Under lights that flicker such as
fluorescent light, images may not
be recorded properly.
• When the whole angle of 3D
panoramic shooting and the angle
in which you fixed the focus and
exposure with AE/AF lock are
extremely different in brightness,
color and focus, the shooting will
not be successful. If this happens,
198
E
H
I
F
J
L
M
G
200
R
N
S
P
Q
201
U
V
Viewing images on a TV screen
W
Wireless Remote Commander
202
SEE
Notes on the License
HTTP://WWW.MPEGLA.COM
“C Library”, “Expat”, “zlib”, “dtoa”,
“pcre”, and “libjpeg” software are
provided in the camera. We provide
this software based on license
agreements with their owners of
copyright. Based on requests by the
owners of copyright of these software
applications, we have an obligation to
inform you of the following. Please
read the following sections.
Read “license1.pdf” in the “License”
folder on the CD-ROM. You will find
licenses (in English) of “C Library”,
“Expat”, “zlib”, “dtoa”, “pcre” and
“libjpeg” software.
On GNU GPL/LGPL applied
software
The software that is eligible for the
following GNU General Public
License (hereinafter referred to as
“GPL”) or GNU Lesser General
Public License (hereinafter referred
to as “LGPL”) are included in the
camera.
This informs you that you have a
right to have access to, modify, and
redistribute source code for these
software programs under the
conditions of the supplied GPL/
LGPL.
Source code is provided on the web.
Use the following URL to download
it.
http://www.sony.net/Products/Linux/
We would prefer you do not contact
us about the contents of source code.
SLT-A55/A55V/A33 IS LICENSED
UNDER THE AVC PATENT
PORTFOLIO LICENSE FOR THE
PERSONAL AND NON-
COMMERCIAL USE OF A
CONSUMER TO
(i) ENCODE VIDEO IN
COMPLIANCE WITH THE AVC
STANDARD (“AVC VIDEO”)
AND/OR
(ii) DECODE AVC VIDEO THAT
WAS ENCODED BY A
CONSUMER ENGAGED IN A
PERSONAL AND NON-
COMMERCIAL ACTIVITY AND/
OR WAS OBTAINED FROM A
VIDEO PROVIDER LICENSED TO
PROVIDE AVC VIDEO.
Read “license2.pdf” in the “License”
folder on the CD-ROM. You will find
licenses (in English) of “GPL”, and
“LGPL” software.
To view the PDF, Adobe Reader is
needed. If it is not installed on your
computer, you can download it from
the Adobe Systems web page:
http://www.adobe.com/
NO LICENSE IS GRANTED OR
SHALL BE IMPLIED FOR ANY
OTHER USE.
ADDITIONAL INFORMATION
MAY BE OBTAINED FROM
MPEG LA, L.L.C.
203
|