Sony SLV KF295CH User Manual

3-000-00-11(1)  
Video Cassette  
Player  
Operating Instructions  
SLV-KA195CH  
SLV-KF295CH  
©1996 by Sony Corporation  
PALNTSC  
PALNTSC  
G
SLV-KF295CH/KA195CH 3-000-000-11 (1)  
Table of contents  
Getting Started  
4
5
6
8
Step 1: Unpacking  
Step 2: Setting up the remote commander  
Step 3: Connecting the unit  
Step 4: Tuning your TV to the unit  
Basic Operations  
10 Playing a tape  
Additional Operations  
EN  
14 Playing/searching at various  
speeds  
16 Karaoke sing-along  
19 Adjusting the picture  
20 Editing with another VCR  
Additional Information  
22 Troubleshooting  
24 Specifications  
25 Index to parts and controls  
28 Index  
3EN  
SLV-KF295ME/PS/KA195ME/PS 3-858-164-11 (1)  
Getting Started  
Step 1  
Unpacking  
Check that you have received the following items with the unit:  
• Remote commander  
• Mains lead  
• Plug adaptor  
• R6 (Size AA) batteries  
• Aerial cable  
(SLV-KA195ME/KF295ME only)  
• Microphone  
• Audio/video cable (3-phono to 3-  
phono) (SLV-KF295 only)  
Checking your model name  
The instructions in this manual are for the 4 models: SLV-KF295ME,  
KF295PS, KA195ME and KA195PS. Check your model number by  
looking at the rear panel of your unit. The SLV-KA195ME is the  
model used for illustration purposes. Any difference in operation is  
clearly indicated in the text, for example, “SLV-KF295ME only.”  
4EN Getting Started  
SLV-KF295ME/PS/KA195ME/PS 3-858-164-11 (1)  
Step 2  
Setting up the remote commander  
Inserting the batteries  
Insert two R6 (size AA) batteries by  
matching the + and – on the  
batteries to the diagram inside the  
battery compartment.  
Remote sensor  
Using the remote commander  
You can use this remote  
commander to operate the unit  
and a Sony TV. To operate this  
unit, point at the remote sensor  
on the unit. To operate the TV,  
point at the remote sensor on  
the TV.  
TV/VIDEO  
;
u
PROG(CH) +/–  
VOL +/–  
To  
Press  
Turn the TV to standby or active mode  
Turn on the TV power  
u
;
Increase (+) or decrease (–) the TV volume  
Change the TVprogramme position  
VOL +/–  
PROG(CH) +/–  
Select an input source of the TV either from aerial in or from line in TV/VIDEO  
Notes  
• With normal use, the batteries should last about three to six months.  
• If you do not use the remote commander for an extended period of time, remove  
the batteries to avoid possible damage from battery leakage.  
• Do not use a new battery with an old one.  
• Do not mix different types of batteries.  
5EN  
Getting Started  
SLV-KF295ME/PS/KA195ME/PS 3-858-164-11 (1)  
Step 3  
Connecting the unit  
AERIAL OUT  
Aerial cable  
AERIAL IN  
AC IN  
to mains  
: Signal flow  
1
2
3
Disconnect the aerial cable from your TV  
and connect it to AERIAL IN on the rear  
panel of the unit.  
AERIAL  
OUT  
IN  
AERIAL  
OUT  
Connect AERIAL OUT of the unit and  
the aerial input of your TV using the  
supplied aerial cable.  
IN  
Connect AC IN of the unit to the mains  
using the supplied mains lead.  
If the mains plug does not fit in the  
wall outlet, use the supplied plug  
adaptor (SLV-KA195ME/KF295ME  
only).  
6EN Getting Started  
SLV-KF295ME/PS/KA195ME/PS 3-858-164-11 (1)  
Additional connections  
For SLV-KA195  
To a TV that has phono type  
audio/video input jacks  
This unit  
TV  
AUDIO VIDEO  
LINE IN  
This additional connection  
improves picture and sound quality.  
Connect the TV as shown on the  
right.  
LINE OUT  
IN  
VIDEO  
AUDIO  
Audio/video cable (not supplied)  
For SLV-KF295  
This unit  
TV  
AUDIO VIDEO  
LINE IN  
IN  
LINE OUT  
VIDEO  
AUDIO  
Audio/video cable  
This unit  
Stereo system  
To a stereo system (SLV-KF295  
only)  
AUDIO VIDEO  
LINE IN  
LINE OUT  
AUX IN  
You can improve sound quality by  
connecting a stereo system as  
shown on the right.  
Audio cable (not supplied)  
7EN  
Getting Started  
SLV-KF295ME/PS/KA195ME/PS 3-858-164-11 (1)  
Step 4  
Tuning your TV to the unit  
If you have connected your unit to the TV using the audio/video cable, skip  
this step.  
u (ON/STANDBY)  
1
2
Press u (ON/STANDBY) to turn on the unit.  
Turn on your TV and select a programme position for video  
playback.  
Choose a channel between UHF 30 and 39 on the TV where there is  
no picture and no sound or only a steady rustling sound.  
This channel will now be referred to as the video channel.  
3
Insert a tape recorded in the colour system matching your TV into  
the cassette compartment.  
The unit starts playing automatically if you insert a tape with its  
safety tab removed.  
4
5
Press · PLAY on the unit.  
Tune the TV until the video playback picture is clearly displayed on  
the TV screen.  
Refer to your TV manual for tuning instructions.  
You have now tuned your TV to the unit. From now on, whenever  
you want to play a tape, set the TV to the video channel.  
If the playback picture does not appear clearly, see “To obtain a clear  
playback picture” on page 9.  
8EN Getting Started  
SLV-KF295ME/PS/KA195ME/PS 3-858-164-11 (1)  
To obtain a clear playback  
picture  
If the playback picture does not  
appear clearly in step 5 above,  
turn the RF CHANNEL screw on  
the rear panel of the unit with a  
screwdriver to a position where  
RF CHANNEL  
the TV clearly displays the playback picture.  
Selecting the TV system  
For your TV to receive the correct  
signal from your unit, you must  
set the TV SYSTEM switch on the  
rear panel of the unit to either G  
(for system B/G) or K (for system  
D/K). If this switch is set to the  
wrong position, the sound will be  
TV SYSTEM  
distorted.  
G
K
9EN  
Getting Started  
SLV-KF295ME/PS/KA195ME/PS 3-858-164-11 (1)  
Basic Operations  
Playing a tape  
6 EJECT  
P PAUSE  
3/#  
SEARCH  
) FF  
· PLAY  
p STOP  
0 REW  
PICTURE  
NTSC PB  
COLOR SYSTEM  
1
2
Turn on your TV and set it to the video channel.  
Insert a tape.  
The unit turns on, and starts playing  
automatically if you insert a tape with its  
safety tab removed.  
10EN Basic Operations  
SLV-KF295ME/PS/KA195ME/PS 3-858-164-11 (1)  
3
Press · PLAY.  
PLAY  
When the tape reaches the end, it will rewind automatically.  
Additional tasks  
To  
Press  
Stop play  
Pause play  
p STOP  
P PAUSE  
Resume play after pause P PAUSE or · PLAY  
Search forward  
Search backward  
Fast-forward the tape  
Rewind the tape  
Eject the tape  
) FF or # SEARCH during playback  
0 REW or 3 SEARCH during playback  
) FF during stop  
0 REW during stop  
6 EJECT  
To set the colour system  
If streaks appear during playback, set COLOR SYSTEM on the unit to  
conform to the system that the tape was recorded in. (Normally set the  
switch to AUTO.)  
If your tape was recorded in  
Set COLOR SYSTEM to  
PAL/MESECAM  
NTSC  
PAL  
NTSC  
MESECAM  
PAL/MESECAM  
continued  
Basic Operations 11EN  
SLV-KF295ME/PS/KA195ME/PS 3-858-164-11 (1)  
Playing a tape (continued)  
To play an NTSC-recorded tape  
Set NTSC PB on the unit according to the colour system of your TV.  
If your TV is  
PAL  
Set NTSC PB to  
ON PAL TV  
NTSC 4.43  
NTSC 4.43  
NTSC 3.58  
NTSC 3.58  
Watching a rental tape  
Set PICTURE on the unit to RENTAL PICTURE. Noise will be reduced on  
the playback picture. After watching the rental tape, set the switch back to  
NORMAL.  
Selecting the sound during  
playback (SLV-KF295 only)  
Press AUDIO MONITOR to select  
the desired sound. Each press of the  
button changes the display on the  
AUDIO MONITOR  
unit. When you play a tape  
recorded in stereo or with a  
bilingual sound track, the HiFi  
indicator on the unit lights up.  
To listen to a  
Press AUDIO MONITOR until the  
display window indicator shows  
Stereo tape’s  
Bilingual tapes  
“L/R”  
“L”  
Stereo sound  
Left channel  
Main and sub sounds  
Main sound  
Right channel  
Standard sound*  
“R”  
Sub sound  
No indication  
Standard sound*  
* The mixed sound of left and right channels (monaural)  
12EN Basic Operations  
SLV-KF295ME/PS/KA195ME/PS 3-858-164-11 (1)  
How sound is recorded on a video tape (SLV-KF295 only)  
The unit records sound onto two separate tracks. Hi-fi audio is recorded  
onto the main track along with the picture. Monaural sound is recorded  
onto the normal audio track along the edge of the tape.  
Stereo  
Mixed left/right  
Bilingual  
Mixed left/right  
channels  
channels  
Normal audio track  
(monaural)  
Hi-fi audio track  
(main track)  
Stereo sound  
(left/right  
Main (left channel)  
Sub (right channel)  
channels)  
Notes  
• Depending on your TV, the following may occur while playing an NTSC-recorded  
tape:  
– the picture is black and white,  
– the picture shakes,  
– no picture appears on the TV screen,  
– black streaks appear horizontally on the TV screen, and  
– the colour density increases or decreases.  
To listen to playback sounds in stereo, you must use the AUDIO OUT connections  
(SLV-KF295 only).  
• When you play a tape recorded in monaural, the sound is heard in monaural  
regardless of the AUDIO MONITOR setting.  
You cannot select the sound to listen to while recording.  
You can playback tapes recorded in the SP mode only.  
You can eject a tape even when the power is off. When you press 6 EJECT, the unit  
turns on automatically. After ejecting the tape, the unit turns off again.  
• When the pause mode lasts for more than approximately five minutes, the unit will  
automatically enter the playback mode.  
Basic Operations 13EN  
SLV-KF295ME/PS/KA195ME/PS 3-858-164-11 (1)  
Additional Operations  
Playing/searching  
at various speeds  
& SLOW +/–  
7 FRAME  
· PLAY  
3/#  
SEARCH  
) FF  
0 REW  
) FF  
· PLAY  
0 REW  
Playback options  
Operation  
During stop, press ) FF or 0 REW.  
Fast-forward/rewind  
View the picture during fast- During fast-forward, hold ) FF down. During rewind, hold  
forward or rewind  
Play at high speed  
Play in slow motion  
0 REW down.  
During playback or pause, press # SEARCH or 3 SEARCH.  
During playback or pause, press & SLOW+/–. Press the +/–  
buttons to change the speed.  
Play frame by frame  
Rewind and start play  
During pause, press 7 FRAME to advance the picture one frame.  
Hold the button down to play one frame each second.  
During stop, hold 0 REW on the unit down and press · PLAY  
on the unit.  
14EN Additional Operations  
SLV-KF295ME/PS/KA195ME/PS 3-858-164-11 (1)  
To resume normal playback  
Press · PLAY.  
Tip  
• If the picture shakes while in the still mode, adjust the picture using $/4  
TRACKING NORMAL/SLOW STILLADJUST on the unit.  
Notes  
• Streaks or snow cannot be eliminated completely in the various playback  
operations.  
• The sound is muted during these operations.  
15EN  
Additional Operations  
SLV-KF295ME/PS/KA195ME/PS 3-858-164-11 (1)  
Karaoke sing-  
along  
You can sing along with a karaoke  
videotape, a TV broadcast, or music  
played back on equipment connected to  
the LINE IN jacks on the rear panel of  
the unit. You can sing duets if you use  
an extra microphone (not supplied).  
MIC VOL 1  
MIC VOL 2  
MIC IN 1/2  
Before you start...  
KARAOKE  
ON/OFF  
· PLAY  
Turn on your TV and set it to the  
video channel.  
ON/OFF  
• Connect the supplied microphone to  
the MIC IN 1 jack. To sing duets,  
connect the optional microphone to  
the MIC IN 2 jack.  
ECHO  
Microphone  
(supplied)  
Singing along with karaoke video tapes  
1
2
Set KARAOKE ON/OFF to ON.  
Insert a karaoke video tape.  
The unit turns on and starts playing automatically if you insert a tape  
with its safety tab removed.  
3
4
Press · PLAY.  
If you want to playback a specific song, see “Searching with the AMS  
function” on page 17.  
Set the ON/OFF switch on the microphone to ON.  
Now you can enjoy playing karaoke.  
To adjust the microphone volume  
Turn the MIC VOL 1 control for the microphone connected to MIC IN 1.  
Turn the MIC VOL 2 control for the microphone connected to MIC IN 2.  
Setting the MIC VOL 1 and/or 2 control(s) to the centre position provides  
the best microphone volume.  
To control the echo effect  
Turn the ECHO control. This controls both microphones’ echo effect in the  
same way.  
To get the best effect, adjust the microphone volume to a slightly higher level  
than the music volume.  
16EN Additional Operations  
SLV-KF295ME/PS/KA195ME/PS 3-858-164-11 (1)  
Reducing the playback  
vocals (Karaoke Pon)  
(SLV-KF295 only)  
You can use ordinary music sources  
with vocals for karaoke with this  
function. Use hi-fi stereo music  
sources.  
KARAOKE PON  
Set KARAOKE PON to ON.  
The singer’s voice will be reduced.  
To cancel Karaoke Pon  
Set KARAOKE PON to OFF.  
Searching with the  
AMS function  
The AMS (Automatic Music  
Sensor) function searches for the  
beginning of the next or previous  
song by detecting a blank space  
between songs.  
Present position  
Blank space  
=/+  
AMS  
· PLAY  
1
2
Press p STOP.  
Press =/+ AMS.  
• To locate the beginning of the next song, press + AMS.  
p STOP  
• To locate the beginning of the previous song, press = AMS.  
The unit starts searching and stops automatically when it locates the  
beginning of the next or previous song.  
3
Press · PLAY to start playback.  
continued  
Additional Operations 17EN  
SLV-KF295ME/PS/KA195ME/PS 3-858-164-11 (1)  
Karaoke sing along (continued)  
Tip  
• When you sing along with music played back on equipment connected to the LINE  
IN jacks on the unit, play the music source and follow steps 1 and 4 on page 16.  
Notes  
• If the sound is reproduced through a stereo amplifier, turn down the volume of  
amplifier before operation.  
• If streaks appear during playback, select the colour system that the tape was  
recorded in (see “To set the colour system” on page 11).  
• If feedback occurs, turn down the microphone or TV volume, or move the  
microphone away from the speakers.  
• Karaoke Pon does not work with the following tapes:  
– tapes on which different vocal sounds are recorded on the left and right channels,  
such as a duet;  
– tapes recorded monaurally; or  
– tapes on which sound sources are recorded with strong echo effects and chorus  
effects.  
• The AMS may not work correctly when:  
– the tape quality is poor,  
– a song is very short (less than 40 seconds),  
– the interval between songs is very short (less than 6 seconds),  
– a high level sound is recorded between songs or at the beginning of a song,  
– there are low level passages or passages without sound in a song,  
– narration is recorded at the beginning of a song,  
– fade-in or fade-out recording is made on the tape, or  
– AMS starts from the very beginning of the tape or near an interval between  
songs.  
18EN Additional Operations  
SLV-KF295ME/PS/KA195ME/PS 3-858-164-11 (1)  
Adjusting the  
picture  
Adjusting the tracking  
Although the unit automatically  
adjusts the tracking when  
playing a tape, distortion may  
occur if the tape was recorded in  
poor condition. If so, manually  
adjust the tracking.  
Press $/4 TRACKING  
$/4  
NORMAL/SLOW to obtain the  
best possible picture. The  
distortion should disappear as  
you press one of the two  
buttons. If you cannot get a  
clear picture with manual  
adjustment, press TRACKING  
AUTO/MANUAL to return to  
automatic adjustment.  
TRACKING  
NORMAL/  
SLOW  
TRACKING  
AUTO/  
MANUAL  
About OPC  
OPC (Optimum Picture Control) automatically improves playback quality  
by adjusting the unit to the condition of the video heads and tape.  
The OPC function automatically works on all types of tapes, including rental  
tapes. You can play a tape using the OPC function even if the tape was not  
recorded with it.  
Notes  
• The auto tracking function works automatically when you play back a tape just  
after inserting it.  
• Sufficient picture quality may not be obtained when playing back tapes recorded on  
another VCR or tapes in poor condition.  
• When a tape recorded with the copyguard system is played back, intermittent  
distortion may appear in the upper portion of the picture. However, this is not a  
malfunction of the unit.  
Additional Operations 19EN  
SLV-KF295ME/PS/KA195ME/PS 3-858-164-11 (1)  
Editing with another VCR  
How to connect to record on this unit  
TV  
This unit (Recorder)  
LINE IN  
Other VCR (Player)  
LINE OUT  
VMC-710/720MS audio/video cable (not supplied)  
: Signal flow  
Tips  
• (SLV-KA195 only)  
If the other VCR has the AUDIO L and R jacks, use a commercially available  
connecting cable like the Sony VMC-910MS.  
• (SLV-KF295 only)  
Use a commercially available connecting cable like the Sony VMC-810. If the other  
VCR is a monaural type, use a conncting cable like the Sony VMC-910MS.  
Notes  
• Make sure you connect the plugs to jacks of the same colour.  
• When connecting the units, do not simultaneously connect the LINE IN and LINE  
OUT jacks on your unit with the other VCR. A humming noise may occur if you do  
this.  
20EN Additional Operations  
SLV-KF295ME/PS/KA195ME/PS 3-858-164-11 (1)  
P PAUSE  
Operation (when  
recording on this unit)  
You can make a copy of a tape  
using this unit for recording or  
playback. The unit cannot record  
TV programmes directly since it  
does not have a TV tuner.  
r REC  
Before you start editing  
Turn on your TV and set it to the video channel.  
1
Insert a source tape with its safety tab removed into the other  
(playback) VCR. Search for the point to start playback and set it to  
playback pause.  
2
Insert a tape with its safety tab in place into this (recording) unit.  
Search for the point to start recording and press P PAUSE.  
3
4
Press r REC on this unit and set it to recording pause.  
To start editing, press the P PAUSE buttons on both units at the same  
time.  
To stop editing  
Press the p STOP buttons on both units.  
To save a recording  
To prevent accidental erasure, break off the  
safety tab as illustrated. To record on a tape  
again, cover the tab hole with adhesive tape.  
Safety tab  
Auto head cleaner  
The unit incorporates the auto head cleaner and cleans the video heads  
when a tape is loaded or unloaded. When the effect is not sufficient even  
after a tape has been loaded/unloaded several times, use the Sony V-25CL  
video head cleaning cassette.  
Tips  
To edit more precisely, press the P PAUSE buttons on the units to release pause.  
To cut out unwanted scenes while editing, press P PAUSE on this unit when an  
unwanted scene begins. When it ends, press P PAUSE again to resume recording.  
Note  
You can record tapes only in SP mode.  
Additional Operations 21EN  
SLV-KF295ME/PS/KA195ME/PS 3-858-164-11 (1)  
Additional Information  
Troubleshooting  
If you have any questions or problems not covered below, please consult your  
nearest Sony service facility.  
Symptom  
Remedy  
The u (ON/STANDBY) switch • Connect the mains lead securely.  
does not function.  
The power is turned on but the  
unit does not operate.  
• Moisture condensation occurs. Turn the power off,  
unplug the mains lead and leave the unit to dry for  
over an hour.  
• The auto safety system is triggered to protect your tape  
and the unit’s mechanism when there is something  
wrong with the tape or when the mechanism is  
overloaded. Press u to restart the unit. If the unit  
does not work after pressing u again, disconnect the  
mains lead from the mains supply. Wait for at least 15  
seconds. Then reconnect mains, and press u again. If  
the unit still does not work, please consult your nearest  
Sony service facility.  
The VCR enters standby mode  
or turns off automatically.  
The playback picture does not  
appear on the TV screen.  
• Make sure the TV is set to the video channel. If you  
are using a monitor, set it to video input.  
The picture is not clear.  
• Adjust the tracking with the $/4 TRACKING  
NORMAL/SLOW buttons.  
• Make sure the COLOR SYSTEM switch is set to the  
position corresponding to the colour system which the  
tape was recorded with.  
• The video heads are dirty (see below). Clean the video  
heads using the Sony V-25CL video head cleaning  
cassette. If this cleaning cassette is not available in  
your area, have the heads cleaned at your nearest Sony  
service facility (a standard service charge will be  
required). Do not use a commercially available wet-  
type cleaning cassette, as it may damage the video  
heads.  
• The video heads may have to be replaced. Consult  
your local Sony service facility for more information.  
• Adjust the vertical hold control on the TV or monitor.  
• The tape is defective. Use a new tape.  
The picture rolls vertically  
during picture search.  
The picture has no sound.  
Symptoms caused by contaminated video heads  
• Normal picture  
• Rough picture  
• Unclear picture  
• No picture (or  
black & white  
screen appears)  
initial  
terminal  
22EN  
Additional Information  
SLV-KF295ME/PS/KA195ME/PS 3-858-164-11 (1)  
Symptom  
Remedy  
The tape starts playing as soon  
as it is inserted.  
• The safety tab has been removed. To record on this  
tape, cover the tab hole.  
The tape is ejected when you  
press r REC.  
• Check that the safety tab has not been removed.  
• Make sure the tape is not at its end.  
Nothing happens when you  
press r REC.  
The microphone sound is  
distorted  
• The MIC VOL control is set too high.  
No tape can be inserted.  
• Check that a tape isn’t already in the tape  
compartment.  
• Make sure you are pointing the remote commander at  
the remote sensor on the unit.  
The remote commander does  
not function.  
• Replace all the batteries in the remote commander with  
new ones if they are weak.  
The unit needs to be cleaned.  
• Clean the cabinet, panel, and controls with a dry soft  
cloth, or a soft cloth slightly moistened with a mild  
detergent solution. Do not use any type of solvent,  
such as alcohol or benzine.  
23EN  
Additional Information  
SLV-KF295ME/PS/KA195ME/PS 3-858-164-11 (1)  
Specifications  
System  
Supplied accessories  
RF output signal  
UHF channels 30 to 39  
Aerial out  
Remote commander (1)  
R6 (Size AA) batteries (2)  
Aerial cable (1)  
75-ohm asymmetrical aerial socket  
Mains lead (1)  
Audio/video cable (3-phono to 3-phono)  
(SLV-KF295 only) (1)  
Microphone (1)  
Inputs and outputs  
LINE IN  
VIDEO IN, phono jack (1)  
Input signal: 1 Vp-p, 75 ohms,  
unbalanced, sync negative  
AUDIO IN,  
phono jack (1) (SLV-KA195)  
phono jack (2) (SLV-KF295)  
Input level: 327 mVrms  
Plug adaptor  
(SLV-KA195ME/ SLV-KF295ME only) (1)  
Design and specifications are subject to change  
without notice.  
Input impedance: more than 47 kilohms  
LINE OUT  
VIDEO OUT, phono jack (1)  
Output signal: 1 Vp-p, 75 ohms,  
unbalanced, sync negative  
AUDIO OUT,  
phono jack (1) (SLV-KA195)  
phono jack (2) (SLV-KF295)  
Standard output: 327 mVrms  
Load impedance: 47 kilohms  
Output impedance: less than 10 kilohms  
Microphone input  
MIC IN 1/2 (2)  
more than 3 kilohms, 1.84 mVrms  
General  
Power requirements  
110 – 240 V AC, 50/60 Hz  
Power consumption  
12 W  
Operating temperature  
5°C to 40°C  
Storage temperature  
–20°C to 60°C  
Dimensions  
Approx. 355 x 102 x 283.5 mm (w/h/d)  
including projecting parts and controls  
Mass  
Approx. 3.8 kg  
24EN  
Additional Information  
SLV-KF295ME/PS/KA195ME/PS 3-858-164-11 (1)  
Index to parts and controls  
Refer to the pages indicated in parentheses ( ) for details.  
Front panel (SLV-KA195)  
REC  
Front panel (SLV-KF295)  
HI-FI  
REC  
L
R
1 u ON/STANDBY switch/indicator (8) !™ p STOP button (11)  
2 § EJECT button (11)  
3 Tape compartment  
P PAUSE button (11)  
PICTURE switch (12)  
!∞ NTSC PB switch (12)  
COLOR SYSTEM switch (11)  
Remote sensor (5)  
4 Tape operation indicators  
5 HiFi L/R indicators (SLV-KF295 only)  
(12)  
6 REC (recording) indicator  
!• MIC VOL 1/2 controls (16)  
MIC IN 1/2 jacks (16)  
ECHO control (16)  
7 AUDIO MONITOR button (SLV-KF295  
only)(12)  
8
03 REW button (11, 14)  
KARAOKE PON (ON/OFF) switch  
9 · PLAY button (11)  
)# FF button (11, 14)  
r REC button (21)  
(SLV-KF295 only) (17)  
@™ KARAOKE (ON/OFF) switch (16)  
continued  
25EN  
Additional Information  
SLV-KF295ME/PS/KA195ME/PS 3-858-164-11 (1)  
Index to parts and controls (continued)  
Rear panel (SLV-KA195)  
Rear panel (SLV-KF295)  
1 AC IN connector (6)  
5 LINE OUT VIDEO/AUDIO jacks  
(SLV-KA195 only)(7)  
2 RF CHANNEL screw (9)  
3 AERIAL OUT connector (6)  
LINE OUT VIDEO/AUDIO L/R  
jacks (SLV-KF295 only)(7)  
4 LINE IN VIDEO/AUDIO  
6 AERIAL IN connector (6)  
jacks (SLV-KA195 only) (20)  
7 TV SYSTEM switch (9)  
LINE IN VIDEO/AUDIO L/R  
jacks (SLV-KF295 only) (20)  
26EN  
Additional Information  
SLV-KF295ME/PS/KA195ME/PS 3-858-164-11 (1)  
Remote commander  
1 6 EJECT button (11)  
2 TV/VTR button (This button doesn’t  
work for this unit)  
3 TV buttons (Only for a TV) (5)  
TV/VIDEO  
; (TV power)  
u (power standby)  
VOL +/–  
PROG (CH) +/–  
4 7 FRAME button (14)  
5 TRACKING AUTO/MANUAL  
button (19)  
6 r REC button (21)  
7 P PAUSE button (11)  
8 0 REW button (11, 14)  
9 p STOP button (11)  
u (on/standby) switch (8)  
& SLOW +/– buttons (14)  
!™ $/4TRACKING NORMAL/SLOW  
STILL ADJUST buttons (19)  
=/+ AMS buttons (17)  
3/# SEARCH buttons (11, 14)  
!∞ · PLAY button (11)  
) FF button (11, 14)  
27EN  
Additional Information  
SLV-KF295ME/PS/KA195ME/PS 3-858-164-11 (1)  
Index  
A, B  
Accessories supplied  
Adjusting  
N
4
Normal audio track 13  
NTSC-recorded tapes 12  
picture 19  
tracking 19  
O
Aerial hookup  
6
OPC (Optimum Picture  
Control) 19  
AMS searching 17  
Audio track 13  
Auto head cleaner 21  
P, Q  
Picture adjustment. See  
Adjusting  
AV connection  
7
C
Playback 10  
at various speeds 11, 14  
frame-by-frame 14  
slow motion 14  
Cleaning the video  
heads 22  
Colour system  
compatible colour  
systems  
setting 11  
Connecting  
2
R
Recording 20  
Remote commander  
Rental tape 12  
RF CHANNEL screw  
5
the VCR and your TV  
to a TV with audio/  
video jacks  
6
9
7
S
D
Safety tab 21  
Searching at various  
speeds 14  
Dubbing. See Editing  
E, F, G  
Echo 16  
Editing 20  
SP mode 13  
T, U, V, W, X, Y, Z  
Tracking adjustment. See  
Adjusting  
Tuning your TV to the  
H, I, J  
Hi-fi audio track 13  
unit  
8
TV system  
9
K, L  
Karaoke sing along 16  
Reducing the playback  
vocals 17  
M
Monitoring  
during playback 12  
28EN  
Additional Information  
SLV-KF295ME/PS/KA195ME/PS 3-858-164-11 (1)  

Whirlpool Cable Box ET4WSKYKQ02 User Manual
Toshiba MA 205 User Manual
Tektronix Car Amplifier P6046 User Manual
TANDBERG MXP 770 User Manual
TANDBERG MXP 550 User Manual
Sub Zero WS 30 User Manual
Sony PRESSMAN User Manual
Sony NEX VG20 User Manual
Sony DCR DVD505E User Manual
Sennheiser 504302 User Manual