Sony Cassette Player XR 4803 User Manual

XR-4803

SERVICE MANUAL

East European Model

Model Name Using Similar Mechanism

Tape Transport Mechanism Type

NEW

MG-25F-136

SPECIFICATIONS

– Continued on next page –

FM/MW/LW CASSETTE CAR STEREO

MICROFILM

SECTION 1

GENERAL

This section is extracted from

instruction manual.

– 3 –

– 4 –

– 5 –

– 6 –

– 7 –

– 8 –

SECTION 2

DISASSEMBLY

Note: Follow the disassembly procedure in the numerical order given.

FRONT PANEL ASS’Y

1 Push the button

(release).

2 Remove the front panel ass’y

to the direction of the arrow A.

COVER ASS’Y

3 cover ass’y

– 9 –

SUB PANEL, MECHANISM DECK (MG-25F-136)

5 screw

(PTT2.6 × 6)

3 connector

(CN351)

6 mechanism deck

(MG-25F-136)

4 flexible flat cable

(CN301)

2 sub panel

1 three screws

(PTT2.6 × 8)

1 three screws

(PTT2.6 × 8)

MAIN BOARD, HEAT SINK

5 two screws

5 three screws

(PTT2.6 × 10)

(PTT2.6 × 5)

1 screw

(PTT2.6 × 8)

3 two ground point

screws

5 screw

(PTT2.6 × 8)

4 main board

6 heat sink

2 rubber cap (25)

1 two screws

(PTT2.6 × 8)

– 10 –

SECTION 3

ASSEMBLY OF MECHANISM DECK

Note: Follow the assembly procedure in the numerical order given.

7 Holder the hanger by bending the claw.

1 Install the catch to the hanger.

HOUSING

5 Fit projection on C part.

2 Install the hanger onto

two claws of the housing.

hanger

4 Fit claw on B part.

3 Put the housing

6 Fit projection on D part.

under A part.

housing

C part

8 Hold the hanger by

bending the claw.

D part

A part

B part

ARM (SUCTION)

2 Move the arm (suction) in the arrow

direction and fit on projection.

projection

1 Fit the arm (suction) on the shaft.

– 11 –

LEVER (LDG-A) / (LDG-B)

shaft A

shaft B

shaft C

shaft A

shaft B

1 Fit the lever (LDG-A) on

shafts A – C and install it.

3 type-E stop ring 2.0

2 Fit the lever (LDG-B) on

shafts A and B and

install it.

GEAR (LDG-FT)

gear (LDG-D)

6 polyethylene washer

hole

5 gear (LDG-FT)

hole

lever (LDG-A)

gear (LDG-FB)

4 Align hole in the gear (LDG-D)

with hole the lever (LDG-A).

2 tension spring (LD-2)

3 Move the lever (LDG-B)

in the arrow direction.

2 tension spring (LD-1)

– 12 –

GUIDE (C)

2 guide (C)

1 three claws

– 13 –

SECTION 5

SECTION 4

ELECTRICAL ADJUSTMENTS

MECHANICAL ADJUSTMENTS

1. Clean the following parts with a denatured-alcohol-moistened

TEST MODE

swab:

This set have the test mode function. In the test mode, FM Auto

Scan/Stop Level andAM (MW)Auto Scan/Stop Level adjustments

can be performed easier than it in ordinary procedure.

playback head pinch roller

rubber belt

idler

capstan

2. Demagnetize the playback head with a head demagnetizer.

3. Do not use a magnetized screwdriver for the adjustments.

4. After the adjustments, apply suitable locking compound to the

parts adjusted.

1. Set the “power select” switch (S501) is “A” position.

2. Turn ON the regulated power supply. (All LEDs on the set

lights up, and the clock is displayed.)

5. The adjustments should be performed with the power supply

voltage unless otherwise noted.

Note: Press the [OFF] button, if the clock is not displayed.

3. Push the preset [4] button.

4. Push the preset [5] button.

• Torque Measurement

5. Press the preset [1] button for more than two seconds.

6. Then the display indicates all lights, the test mode is set.

Mode

Torque Meter

Meter Reading

30 – 65 g•cm

(0.42 – 0.90 oz•inch)

1. Push the [OFF] button.

2. Return the “power select” switch (S501) to initially set posi-

tion.

Forward

CQ-102C

Forward

Back Tension

0.5 – 4.5 g•cm

(0.01 – 0.06 oz•inch)

CQ-102C

CQ-102RC

CQ-201B

30 – 65 g•cm

(0.42 – 0.90 oz•inch)

Reverse

See the adjustment location from on page 16 for the

adjustment.

Reverse

Back Tension

0.5 – 4.5 g•cm

(0.01 – 0.06 oz•inch)

60 – 200 g•cm

(0.83 – 2.78 oz•inch)

FF, REW

0 dB=0.775 V

TAPE DECK SECTION

Tape Speed Adjustment

• Tape Tension Measurement

Setting:

Mode

Tension Meter

Meter Reading

speed checker

more than 90 g

(more than 3.18 oz)

Forward

CQ-403A

frequency counter

test tape

more than 90 g

(more than 3.18 oz)

Reverse

CQ-403R

WS-48A

(3 kHz, 0 dB)

4 Ω

set

–

speaker out terminal

Procedure:

1. Put the set into the FWD PB mode.

2. Adjust adjustment resistor for inside capstan motor so that the

reading on the speed checker or frequency counter becomes in

specification.

Specification: Constant speed

Speed checker

Frequency counter

–1.5 to +2.5%

2,955 to 3,075 Hz

Adjustment Location: See page 16.

– 14 –

FM Stereo Separation Adjustment

Setting:

0 dB=1 µV

TUNER SECTION

[SOURCE] button: FM

Cautions during repair

When the tuner unit is defective, replace it by a new one be-

cause its internal block is difficult to repair.

FM RF signal

level meter

antenna jack (J1)

generator

4 Ω

0.01 µF

Note: Adjust the tuner section in the sequence shown below.

1. FM Auto Scan/Stop Level Adjustment.

2. FM Stereo Separation Adjustment.

–

set

3. AM (MW) Auto Scan/Stop Level Adjustment.

Carrier frequency : 98.0 MHz

speaker out terminal

Output level

Mode

: 70 dB (3.2 mV)

: stereo

FM Auto Scan/Stop Level Adjustment

Setting:

Modulation

: main: 1 kHz, 20 kHz deviation (26.7%)

sub: 1 kHz, 20 kHz deviation (26.7%)

19 kHz pilot: 7.5 kHz deviation (10%)

[SOURCE] button: FM

Procedure:

FM RF signal

generator

FM Stereo

signal generator

output channel

antenna jack (J1)

0.01 µF

Level meter

connection

Level meter

reading (dB)

set

L-CH

R-CH

L-CH

R-CH

Carrier frequency : 98.0 MHz

Adjust RV4 on TU1

for minimum reading.

Output level

Mode

Modulation

: 22 dB (12.6 µV)

: mono

: 1 kHz, 22.5 kHz deviation (30%)

Procedure:

1. Set to the test mode. (See page 14.)

Adjust RV4 on TU1

for minimum reading.

2. Push the [SOURCE] button and set to FM.

L-CH Stereo separation: A-B

R-CH Stereo separation: C-D

Display

The separations of both channels should be equal.

Specification: Separation more than 28 dB

Adjustment Location: See page 16.

98.0

SHUF1

3. Adjust with the volume RV2 on TU1 so that the “FM” indica-

tion turns to “FMI” indication on the display window.

But, in case of already indicated “FMI”, turn the RV2 so that

put out light “I” indication and adjustment.

Display

98.0

SHUF1

Adjustment Location: See page 16.

– 15 –

AM (MW) Auto Scan/Stop Level Adjustment

Make this adjustment after “FMAuto Scan/Stop LevelAdjustment”.

Setting:

Adjustment Location:

—SET UPPER VIEW–

[SOURCE] and [MODE] button: MW

Tape Speed Adjustment

Ω

15 pF

65 pF

AM RF signal

generator

AM dummy antenna

(50 Ω)

set

antenna jack (J1)

Carrier frequency : 999 kHz

30% amplitude

TU1

modulation by

1 kHz signal

Output level

: 33 dB (44.7 µV)

Procedure:

1. Set to the test mode. (See page 14.)

2. Push the [SOURCE] button and set to FM.

3. Push the [MODE] button and set to MW.

Display

INTRO

999

SHUF1

4. Adjust with the volume RV1 on TU1 so that the “MW” indi-

cation turns to “MWI” indication on the display window.

But, in case of already indicated “MWI”, turn the RV1 so that

put out light “I” indication and adjustment.

RV4 FM Stereo Separation Adjustment

Display

RV2 FM Auto Scan/Stop Level Adjustment

RV1 AM (MW) Auto Scan/Stop Level Adjustment

INTRO

999

SHUF1

– 16 –

SECTION 6

DIAGRAMS

6-1. IC PIN FUNCTION DESCRIPTION

• MAIN BOARD IC501 µPD17707GC-529-3B9 (SYSTEM CONTROLLER)

Pin No.

Pin Name

AMSSEL

POS3

I/O

Function

Setting terminal for the AMS selection fixed at “L”

POS2

Tape position detect input from tape operation switch on the mechanism block

POS0

POS1

TAPEON

CM ON

Tape system power supply on/off control signal output terminal “H”: tape on

Capstan/reel motor (M901) drive signal output terminal “H”: motor on

Loading/tape operation motor control signal output to the MM1322XFBE (IC351)

(For the loading direction and forward side operation) *1

LM LOD

LM EJ

Loading/tape operation motor control signal output to the MM1322XFBE (IC351)

(For the eject direction and reverse side operation) *1

TUNON

FM ON

PW ON

MUT

—

Tuner system power supply on/off control signal output to the BA3918 (IC611) “H”: tuner on

FM system power supply on/off control signal output to the BA3918 (IC611) “H”: FM on

Main system power supply on/off control signal output to the BA3918 (IC611) “H”: power on

Line muting control signal output terminal “H”: line muting on

Chip enable signal output to the electrical volume (IC331)

Serial data transfer clock signal output to the electrical volume (IC331)

Serial data output to the electrical volume (IC331)

VOLCE

VOLCKO

VOLSO

AMPON

AMPMUT

DX/LO

NCO

Standby control signal output to the power amplifier (IC751) “L”: standby

Muting control signal output to the power amplifier (IC751) “L”: muting on

Local/DX selection signal output to the FM/AM tuner unit (TU1) “L”: DX, “H”: local

Not used (open)

GND

Ground terminal

DSTSEL

D-BASS

Destination setting terminal (fixed at center voltage)

D-BASS switch (SW951) input (A/D input)

Key input terminal (A/D input)

6, INTRO 1, REPEAT 2, 3, BL SKIP 6, ATA 5, MTL 4 keys input (LSW921 to LSW927)

KEYIN1

Key input terminal (A/D input)

OFF, SOURCE, MODE *, + ) + SEEK AMS, – = 0 SEEK AMS, VOLUME –,

SEL, VOLUME +, ATT, DSPL, BTM, LCL keys input

(LSW901 to LSW909, LSW930, LSW911 and LSW912)

KEYIN0

RC IN0

VSM

Rotary remote commander shift key A/D input terminal

FM and AM (MW/LW) signal meter voltage detection input from the FM/AM tuner unit (TU1)

AM (MW/LW) intermediate frequency detection signal input from the FM/AM tuner unit (TU1)

FM intermediate frequency detection signal input from the FM/AM tuner unit (TU1)

Power supply terminal (+5V)

AMIFIN

FMIFIN

VDD2

FM OSC

AM OSC

GND

—

FM local oscillator detection signal input from the FM/AM tuner unit (TU1)

AM (MW/LW) local oscillator detection signal input from the FM/AM tuner unit (TU1)

Ground terminal

—

NCO

Not used (open)

EO1

Main charge-pump control signal output terminal

TEST0

NCO

Setting terminal for the test (fixed at “L”)

Not used (open)

SEKOUT

MW SW

BEEP

Seek control signal output to the FM/AM tuner unit (TU1)

MW/LW selection signal output to the FM/AM tuner unit (TU1) “L”: MW, “H”: LW

Beep sound output terminal

– 17 –

Pin No.

Pin Name

KEYACK

BU IN

I/O

Function

Input of acknowledge signal for the key entry Acknowledge signal is input to accept function

and eject keys in the power off status On at input of “L”

Battery detect signal input terminal “H”: battery on

METAL control in/out terminal

At initial mode: auto/manual mode selection input of METAL function “L”: manual mode

At manual mode: METAL on/off control signal output to the CXA2509AQ (IC301)

“H”: METAL on

MTLSEL

I/O

At auto mode: input at MTLIN (pin %ª)

Dolby control in/out terminal

At initial mode: valid/invalid selection input of dolby function (“L” input: valid)

At normal mode: dolby on/off control signal output “H”: dolby on

Not used this function in this set (fixed at “H”)

DOLON

AMSIN

I/O

Whether a music is present or not from CXA2509AQ (IC301) is detected at auto music sensor

“L”: music is present, “H”: music is not present

Input of FM stereo detection signal from FM/AM tuner unit (TU1), and output of forced

monaural control signal to FM/AM tuner unit (TU1) (Commonly used for stereo display input

and forced monaural output)

I/O

FM stereo detection at input of “L”, forced monaural at output of “L”

Tape auto music sensor control signal output to the CXA2509AQ (IC301)

“L” is output to lower the gain for audio level at FF/REW

AMS ON

Forward/reverse direction control signal output to the CXA2509AQ (IC301)

“L: forward direction, “H”: reverse direction

N/R OUT

TAPMUT

Tape muting on/off control signal output to the CXA2509AQ (IC301) “H”: tape muting on

Power supply on/off control signal output terminal at the illumination and liquid crystal display

driver (IC901) “H”: power on

At power select switch (S501) on mode: “H” output at the accessory on

At power select switch (S501) off mode: “H” output at the power on

ILLON

Station detector detect input from the FM/AM tuner unit (TU1)

Stop level for SEEK, BTM, etc. is determined SD is present at input of “H”

SD IN

NOSESW

TELMUTE

Detects the removal of the attaching and removing type front panel block “L”: attaching

Telephone muting signal input terminal At input of “L”, the signal is attenuated by –20 dB

Not used (fixed at “H”)

REL

Reel table rotation detect signal input from the take-up and supply reel sensor

Accessory detect signal input terminal “L”: accessory on

ACCIN

TESTIN

RC IN1

Setting terminal for the test mode “L”: test mode (normally fixed at “H”)

Rotary remote commander shift key A/D input terminal

Power select switch (S501) input terminal

“L”: position A (halt mode), “H”: position B (operation mode)

PW SEL

MTLIN

Input terminal to set whether the auto metal function is present or not

“L”: auto metal function is present (fixed at “H”)

ADON

KEYSEL

Power supply on/off control signal output for the A/D conversion

Setting terminal for the key (fixed at “H”)

SEKOUTSEL

COLORSEL

LCDCE

Active selection terminal for the SEKOUT (pin #•) (fixed at “L”)

Setting terminal for the illumination color “L”: amber, “H”: green Not used (fixed at “L”)

Chip enable output to the liquid crystal display driver (IC901)

Serial data transfer clock signal output to the liquid crystal display driver (IC901)

Serial data output to the liquid crystal display driver (IC901)

LCDCKO

LCDSO

Blank indicate control signal output to the liquid crystal display driver (IC901)

“L”: no display

LCDINH

UNICKI

Serial data reading clock signal input terminal for the unilink Not used (connected to pin &¡)

– 18 –

Pin No.

Pin Name

UNISO

UNISI

UNICKO

BUSON

SYSRST

VREG

GND

I/O

Function

Serial data output terminal for the unilink Not used (open)

Serial data input terminal for the unilink Not used (fixed at “L”)

Serial data transfer clock signal output terminal for the unilink Not used (connected to pin ^•)

Bus on/off control signal output terminal Not used (pull up)

Reset signal output terminal “L”: reset Not used (pull up)

CPU regulator output terminal Connected to capacitor

Ground terminal

—

X OUT

X IN

Main system clock output terminal (4.5 MHz)

Main system clock input terminal (4.5 MHz)

CPU chip enable signal input (fixed at “H”)

VDD1

—

Power supply terminal (+5V)

System reset signal input from the reset signal generator (IC551) and reset switch (S551)

“L” is input for several 100 msec after power on, then it changes to “H”

RESET

*1 loading/tape operation motor control

MODE

STOP

LOADING/

FORWARD REVERSE

EJECT/

BRAKE

TERMINAL

LM LOD (pin 8)

“L”

“H”

“L”

“H”

LM EJ (pin 9)

– 19 –

• IC Block Diagrams – MAIN Board –

IC301 CXA2509AQ-T4

IC351 MM1322XFBE

GND

OUT2

29 28 27 26

23 22 21

24dB

IN2

120µ/70µ

VCC

–

MSMODE

19 DRSW

–

IN1

NR BIAS

TAPE/AUX

TAPE EQ

FWD/RVS

VCC

MODE

OUT1

GND

PBFB2 31

PBRIN2 32

TAPESW

PBREF2

PBFIN2

17 INSW

16 NC

VCT 35

VCT

15 NC

PBGND

MS ON/

OFF

LPF

–

DETECT

14 MSOUT

13 DGND

PBFIN1

–

PBREF1 38

PBRIN1

PBFB1

12 MSTC

11 G1FB

–

120µ/70µ

24dB

IC331 LC75373ED

31 30 29

28 27 26

25 24

–

22 LFIN

–

21 LFOUT

LSELO

L4 35

L3 36

L2 37

L1 38

–

LROUT

VREF

–

VDD 39

–

SHIFT

DECODER

LATCH

CONTROL

–

R2 41

R3 42

R4 43

VSS

RROUT

–

RSELO 44

–

RFOUT

–

12 RFIN

– 31 –

IC611 BA3918-V2

REGULATOR

OVER VOLTAGE

PROTECT

–

– 32 –

SECTION 7

EXPLODED VIEWS

NOTE:

•

-XX and -X mean standardized parts, so they

may have some difference from the original

one.

Color Indication of Appearance Parts

Example:

KNOB, BALANCE (WHITE) . . . (RED)

• Items marked “*” are not stocked since they

are seldom required for routine service. Some

delay should be anticipated when ordering

these items.

• The mechanical parts with no reference num-

ber in the exploded views are not supplied.

• Hardware (# mark) list and accessories and

packing materials are given in the last of the

electrical parts list.

•

↑

Parts Color Cabinet's Color

(1) CHASSIS SECTION

MG-25F-136

F781

Front panel ass’y

Ref. No.

Part No.

Description

Remark

Ref. No.

Part No.

Description

Remark

3-009-294-01 PANEL, SUB

3-935-003-01 SPRING, TORSION

3-932-205-21 DOOR, CASSETTE

X-3367-636-1 LOCK ASSY

1-776-207-41 CORD (WITH CONNECTOR) (POWER)

3-009-809-01 BRACKET (IC)

3-010-517-01 HEAT SINK (BUS NON) (E)

3-935-014-01 CUSHION (U)

* 10

* 11

* 5

3-010-377-01 INSULATOR

* 13

3-009-813-01 CHASSIS

* 6

* 8

A-3313-396-A MAIN BOARD, COMPLETE

3-915-923-01 SCREW, GROUND POINT

X-3373-270-1 COVER ASSY

F781

3-012-859-01 CAP (25), RUBBER

3-937-650-01 PLATE (C), GROUND

1-532-877-11 FUSE (BLADE TYPE) (AUTO FUSE) (10A)

– 33 –

(2) FRONT PANEL SECTION

102

not supplied

(KEY board)

109

108

118

117

120

107

116

106

105

111

115

121

LCD901

114

112

104

103

113

101

Ref. No.

Part No.

Description

Remark

Ref. No.

Part No.

Description

Remark

101

102

103

104

105

3-018-799-01 BUTTON (D-BASS)

112

113

* 114

* 115

* 116

3-016-928-11 BUTTON (4-6) (4. 5. 6)

3-015-036-01 CUSHION (BACK PANEL)

3-016-924-01 BUTTON (L) (2) (+. –)

3-009-304-01 BUTTON (RELEASE)

3-932-475-01 SPRING (RELEASE)

3-016-930-01 BUTTON (R) (3) (BTM. LCL. r)

3-019-151-01 PLATE (LCD), GROUND

3-019-150-01 SHEET (REFLECTOR)

3-018-612-01 PLATE, LIGHT GUIDE

* 106

107

108

3-019-149-01 PLATE, LCD

* 117

118

* 120

* 121

3-018-611-01 HOLDER (LCD)

3-010-519-01 PANEL, FRONT BACK

3-024-391-01 SHEET (LCD)

X-3374-689-1 PANEL SUB ASSY

3-009-300-01 BUTTON (SOURCE)

3-018-797-11 BUTTON (L) (3)

109

3-024-846-01 SHEET (LCD) B

(+ + ). SEEK AMS. = 0 –. r. OFF. SEL. ATT)

LCD901 1-801-966-11 DISPLAY PANEL, LIQUID CRYSTAL

111

3-016-927-01 BUTTON (1-3) (6. 1. 2. 3)

– 34 –

(3) MECHANISM DECK SECTION

(MG-25F-136)

160

159

163

158

155

161

HP901

154

162

157

M901

156

164

153

152

165

168

166

167

151

Ref. No.

Part No.

Description

Remark

Ref. No.

Part No.

Description

Remark

151

* 152

* 153

154

A-3291-667-A CLUTCH (FR) ASSY

3-019-130-01 LEVER (LDG-A)

3-019-131-01 LEVER (LDG-B)

3-020-539-01 SPRING (LD-1), TENSION

3-020-540-01 SPRING (LD-2), TENSION

161

162

163

164

165

3-933-346-01 CATCHER

3-933-344-01 GUIDE (C)

3-014-798-01 SCREW (HEAD), SPECIAL

3-364-151-01 WASHER

155

A-3301-267-A CHASSIS ASSY (F)

156

157

158

3-020-542-01 GEAR (LOADING FT)

3-341-753-11 WASHER, POLYETHYLENE

3-020-533-01 HOUSING

166

167

168

3-017-302-01 BELT (25)

3-936-853-01 FLYWHEEL (F)

3-701-437-21 WASHER

* 159

160

3-020-532-01 ARM (SUCTION)

3-020-534-01 HANGER

HP901 1-500-157-21 HEAD, MAGNETIC (PLAYBACK)

M901 A-3291-665-A MOTOR ASSY, MAIN (CAPSTAN/REEL)

– 35 –

SECTION 8

ELECTRICAL PARTS LIST

KEY

NOTE:

When indicating parts by reference

number, please include the board.

• Due to standardization, replacements in the

parts list may be different from the parts speci-

fied in the diagrams or the components used

on the set.

•

Items marked “*” are not stocked since they

are seldom required for routine service.

Some delay should be anticipated when order-

ing these items.

• -XX and -X mean standardized parts, so they

may have some difference from the original

one.

• RESISTORS

All resistors are in ohms.

METAL: Metal-film resistor.

METAL OXIDE: Metal oxide-film resistor.

F: nonflammable

•

SEMICONDUCTORS

In each case, u: µ, for example:

uA. .

: µA. .

uPA. . : µPA. .

uPC. . : µPC. .

uPB. . : µPB. .

uPD. . : µPD. .

CAPACITORS

uF: µF

•

COILS

uH: µH

Ref. No.

Part No.

Description

Remark

Ref. No.

Part No.

Description

Remark

KEY BOARD

LSW906 1-762-619-11 SWITCH, KEY BOARD (WITH LED) (–)

**********

LSW907 1-762-619-11 SWITCH, KEY BOARD (WITH LED) (SEL)

LSW908 1-762-619-11 SWITCH, KEY BOARD (WITH LED) (+)

LSW909 1-762-619-11 SWITCH, KEY BOARD (WITH LED) (ATT)

LSW911 1-762-619-11 SWITCH, KEY BOARD (WITH LED) (BTM)

3-018-611-01 HOLDER (LCD)

3-018-612-01 PLATE, LIGHT GUIDE

3-019-149-01 PLATE, LCD

3-019-150-01 SHEET (REFLECTOR)

3-019-151-01 PLATE (LCD), GROUND

LSW912 1-762-619-11 SWITCH, KEY BOARD (WITH LED) (LCL)

LSW921 1-762-619-11 SWITCH, KEY BOARD (WITH LED) (6)

LSW922 1-762-619-11 SWITCH, KEY BOARD (WITH LED) (1/INTRO)

LSW923 1-762-619-11 SWITCH, KEY BOARD (WITH LED) (2/REPEAT)

LSW924 1-762-619-11 SWITCH, KEY BOARD (WITH LED) (3)

< CAPACITOR >

C901

C902

C903

C904

1-163-033-00 CERAMIC CHIP 0.022uF

1-165-319-11 CERAMIC CHIP 0.1uF

1-163-137-00 CERAMIC CHIP 680PF

50V

LSW925 1-762-619-11 SWITCH, KEY BOARD (WITH LED) (6/BL SKIP)

LSW926 1-762-619-11 SWITCH, KEY BOARD (WITH LED) (5/ATA)

LSW927 1-762-619-11 SWITCH, KEY BOARD (WITH LED) (4/MTL)

LSW930 1-762-619-11 SWITCH, KEY BOARD (WITH LED) (DSPL)

< CONNECTOR >

< PILOT LAMP >

CNP901 1-764-423-11 PIN, CONNECTOR 12P

< DIODE >

PL901 1-517-633-21 LAMP, PILOT (LCD BACK LIGHT)

PL902 1-517-633-21 LAMP, PILOT (LCD BACK LIGHT)

D901

D902

D903

D904

D905

8-719-420-90 DIODE MA8051-M

8-719-422-64 DIODE MA8062-M

< RESISTOR >

R901

R902

R903

R904

R905

1-216-647-11 METAL CHIP

1-216-651-11 METAL CHIP

1-216-655-11 METAL CHIP

680

0.5% 1/10W

< IC >

1.5K

IC901 8-759-443-68 IC LC75834JED

< CHIP CONDUCTOR >

JC902 1-216-295-00 SHORT

R906

R907

R908

R911

R921

1-216-655-11 METAL CHIP

1-216-659-11 METAL CHIP

1-216-663-11 METAL CHIP

1-208-806-11 RES, CHIP

1-216-647-11 METAL CHIP

1.5K

2.2K

3.3K

10K

680

0.5% 1/10W

1/10W

0.5% 1/10W

JC951 1-216-296-00 SHORT

JC952 1-216-296-00 SHORT

R922

R923

R924

R925

R926

1-216-647-11 METAL CHIP

1-216-651-11 METAL CHIP

1-216-655-11 METAL CHIP

680

1.5K

0.5% 1/10W

< LIQUID CRYSTAL DISPLAY >

LCD901 1-801-966-11 DISPLAY PANEL, LIQUID CRYSTAL

< SWITCH >

R941

R942

R951

R952

R953

1-216-667-11 METAL CHIP

1-216-671-11 METAL CHIP

1-216-190-00 RES, CHIP

1-216-089-00 RES, CHIP

1-216-049-11 RES, CHIP

4.7K

6.8K

470

47K

0.5% 1/10W

LSW901 1-762-619-11 SWITCH, KEY BOARD (WITH LED) (OFF)

LSW902 1-762-619-11 SWITCH, KEY BOARD (WITH LED) (SOURCE)

LSW903 1-762-619-11 SWITCH, KEY BOARD (WITH LED)

(MODE *)

1/8W

1/10W

LSW904 1-762-619-11 SWITCH, KEY BOARD (WITH LED) (+ + ))

LSW905 1-762-619-11 SWITCH, KEY BOARD (WITH LED) (= 0 –)

R954

R955

1-216-049-11 RES, CHIP

1/10W

– 36 –

KEY MAIN

Ref. No.

C124

Part No.

Description

Remark

Ref. No.

Part No.

Description

Remark

R956

R962

R963

1-216-049-11 RES, CHIP

1-216-025-00 RES, CHIP

1-216-033-00 METAL CHIP

100

220

1/10W

1-164-004-11 CERAMIC CHIP 0.1uF

10%

25V

C151

C152

C161

C162

C163

1-163-037-11 CERAMIC CHIP 0.022uF 10%

25V

50V

1-124-257-00 ELECT

1-126-160-11 ELECT

2.2uF

1uF

20%

R964

R965

R967

R968

R981

1-216-035-00 METAL CHIP

1-216-033-00 METAL CHIP

1-216-655-11 METAL CHIP

270

220

1.5K

1/10W

1-164-182-11 CERAMIC CHIP 0.0033uF 10%

0.5% 1/10W

C164

C165

C166

C167

C168

1-163-037-11 CERAMIC CHIP 0.022uF 10%

1-126-157-11 ELECT

1-164-492-11 CERAMIC CHIP 0.15uF

1-126-157-11 ELECT

25V

16V

10uF

20%

10%

20%

R982

R983

R984

R999

1-216-663-11 METAL CHIP

1-216-671-11 METAL CHIP

1-216-081-00 METAL CHIP

1-216-308-00 METAL CHIP

3.3K

6.8K

22K

4.7

0.5% 1/10W

1/10W

10uF

C169

C170

C171

C172

C181

1-163-227-11 CERAMIC CHIP 10PF

1-163-157-00 CERAMIC CHIP 10PF

0.5PF 50V

< SWITCH >

50V

1-126-163-11 ELECT

4.7uF

20%

SW951 1-762-937-11 SWITCH, ROTARY (D-BASS)

************************************************************

1-163-009-11 CERAMIC CHIP 0.001uF 10%

1-126-163-11 ELECT 4.7uF 20%

A-3313-396-A MAIN BOARD, COMPLETE

C182

C183

C191

C201

C202

1-163-009-11 CERAMIC CHIP 0.001uF 10%

50V

*********************

1-163-251-11 CERAMIC CHIP 100PF

1-163-263-11 CERAMIC CHIP 330PF

3-009-809-01 BRACKET (IC)

3-010-517-01 HEAT SINK (BUS NON) (E)

7-685-793-09 SCREW +PTT 2.6X8 (S)

C204

C205

C206

C207

C208

1-164-232-11 CERAMIC CHIP 0.01uF

1-164-489-11 CERAMIC CHIP 0.22uF

1-163-227-11 CERAMIC CHIP 10PF

50V

16V

0.5PF 50V

< CAPACITOR >

10%

1-163-235-11 CERAMIC CHIP 22PF

1-163-009-11 CERAMIC CHIP 0.001uF 10%

1-126-933-11 ELECT

1-126-157-11 ELECT

1-126-933-11 ELECT

50V

10V

16V

10V

1-126-163-11 ELECT

4.7uF

20%

50V

100uF

10uF

100uF

20%

C209

C251

C252

C261

C262

1-163-251-11 CERAMIC CHIP 100PF

1-163-037-11 CERAMIC CHIP 0.022uF 10%

50V

25V

50V

1-124-257-00 ELECT

1-126-160-11 ELECT

2.2uF

1uF

20%

C10

1-164-232-11 CERAMIC CHIP 0.01uF

1-163-251-11 CERAMIC CHIP 100PF

50V

C263

C264

C265

C266

C267

1-164-182-11 CERAMIC CHIP 0.0033uF 10%

1-163-037-11 CERAMIC CHIP 0.022uF 10%

50V

25V

16V

1-163-009-11 CERAMIC CHIP 0.001uF 10%

1-126-157-11 ELECT

10uF

20%

10%

C11

C12

C13

C14

C16

1-126-160-11 ELECT

1-163-009-11 CERAMIC CHIP 0.001uF 10%

1-163-251-11 CERAMIC CHIP 100PF

1-164-232-11 CERAMIC CHIP 0.01uF

1uF

20%

50V

1-164-492-11 CERAMIC CHIP 0.15uF

C268

C269

C270

C271

C272

1-126-157-11 ELECT

10uF

20%

16V

0.5PF 50V

1-163-227-11 CERAMIC CHIP 10PF

C17

C18

C19

C22

C23

1-163-009-11 CERAMIC CHIP 0.001uF 10%

1-163-059-00 CERAMIC CHIP 0.01uF

1-164-222-11 CERAMIC CHIP 0.22uF

1-124-584-00 ELECT

1-124-234-00 ELECT

50V

25V

10V

16V

1-126-163-11 ELECT

4.7uF

20%

50V

10%

1-163-009-11 CERAMIC CHIP 0.001uF 10%

100uF

22uF

20%

C281

C282

C283

C301

C302

1-126-163-11 ELECT

4.7uF

20%

50V

16V

25V

1-163-009-11 CERAMIC CHIP 0.001uF 10%

1-163-251-11 CERAMIC CHIP 100PF

20%

10%

C25

C26

C27

C101

C102

1-109-982-11 CERAMIC CHIP 1uF

1-163-989-11 CERAMIC CHIP 0.033uF 10%

1-164-222-11 CERAMIC CHIP 0.22uF

1-163-263-11 CERAMIC CHIP 330PF

10%

10V

25V

50V

1-124-234-00 ELECT

1-131-359-41 ELECT

22uF

10uF

C303

C304

C305

C306

C331

1-163-251-11 CERAMIC CHIP 100PF

1-164-004-11 CERAMIC CHIP 0.1uF

1-107-823-11 CERAMIC CHIP 0.47uF

1-164-232-11 CERAMIC CHIP 0.01uF

10%

50V

25V

16V

50V

10V

C104

C105

C106

C107

C108

1-164-232-11 CERAMIC CHIP 0.01uF

1-164-489-11 CERAMIC CHIP 0.22uF

1-163-227-11 CERAMIC CHIP 10PF

50V

16V

10%

0.5PF 50V

1-124-584-00 ELECT

100uF

20%

C332

C353

C354

C355

C356

1-124-234-00 ELECT

22uF

20%

16V

50V

16V

1-126-163-11 ELECT

4.7uF

20%

50V

1-163-251-11 CERAMIC CHIP 100PF

1-126-157-11 ELECT

1-126-934-11 ELECT

10uF

220uF

C109

C121

C122

C123

1-163-251-11 CERAMIC CHIP 100PF

1-163-809-11 CERAMIC CHIP 0.047uF 10%

1-164-492-11 CERAMIC CHIP 0.15uF

1-164-004-11 CERAMIC CHIP 0.1uF

50V

25V

16V

25V

10%

C357

1-163-251-11 CERAMIC CHIP 100PF

50V

– 37 –

MAIN

Ref. No.

Part No.

Description

< DIODE >

Remark

Ref. No.

Part No.

Description

Remark

C358

C359

C501

C502

1-163-251-11 CERAMIC CHIP 100PF

1-164-489-11 CERAMIC CHIP 0.22uF

1-163-235-11 CERAMIC CHIP 22PF

1-163-234-11 CERAMIC CHIP 20PF

10%

50V

16V

50V

8-719-991-65 DIODE SB02W03C

8-719-423-10 DIODE MA8100-M-TX

8-719-420-90 DIODE MA8051-M

8-719-404-49 DIODE MA111

D21

D91

D301

D351

C503

C504

C505

C551

C552

1-124-584-00 ELECT

100uF

20%

10%

10V

25V

5.5V

10V

1-164-004-11 CERAMIC CHIP 0.1uF

1-163-077-00 CERAMIC CHIP 0.1uF

1-125-701-11 DOUBLE LAYER 0.047F

8-719-035-91 DIODE MA4091-H (TA)

D352

D501

D551

D552

D553

8-719-404-49 DIODE MA111

8-719-400-20 DIODE MA152WA

8-719-404-49 DIODE MA111

1-124-584-00 ELECT

100uF

20%

C553

C554

C571

C582

C602

1-164-004-11 CERAMIC CHIP 0.1uF

1-126-163-11 ELECT

1-163-009-11 CERAMIC CHIP 0.001uF 10%

1-164-222-11 CERAMIC CHIP 0.22uF

10%

20%

25V

50V

25V

4.7uF

D571

D572

D582

D583

D601

8-719-034-94 DIODE MA4180-M (QZ)

8-719-110-03 DIODE RD7.5ESB2

8-719-057-80 DIODE MA8160-M-TX

8-719-422-76 DIODE MA8075-M

8-719-423-32 DIODE MA8120-M

C611

C612

C613

C614

C615

1-126-157-11 ELECT

1-163-077-00 CERAMIC CHIP 0.1uF

1-126-157-11 ELECT

10uF

20%

10%

20%

16V

25V

16V

10uF

D621

D622

D701

D702

D703

8-719-035-54 DIODE MA4039-M (TA)

8-719-911-19 DIODE 1SS119

8-719-035-77 DIODE MA4068-L (TA)

8-719-035-74 DIODE MA4062-M (TA)

C616

C617

C621

C622

C623

1-126-157-11 ELECT

1-163-133-00 CERAMIC CHIP 470PF

1-124-589-11 ELECT 47uF

10uF

20%

16V

50V

16V

D704

D705

D706

D707

D708

8-719-035-74 DIODE MA4062-M (TA)

8-719-034-94 DIODE MA4180-M (QZ)

8-719-035-74 DIODE MA4062-M (TA)

20%

C701

C702

C703

C751

C752

1-163-077-00 CERAMIC CHIP 0.1uF

1-126-096-11 ELECT

1-107-682-11 CERAMIC CHIP 1uF

10%

20%

10%

25V

35V

16V

10uF

D709

D721

D722

D723

D724

8-719-035-74 DIODE MA4062-M (TA)

8-719-970-02 DIODE 1SR139-400

C754

C755

C781

C782

C783

1-126-157-11 ELECT

1-126-096-11 ELECT

1-126-936-11 ELECT

1-163-181-00 CERAMIC CHIP 100PF

10uF

20%

3300uF 20%

16V

35V

16V

50V

D731

D732

D733

D734

D781

8-719-970-02 DIODE 1SR139-400

8-719-049-38 DIODE 1N5404TU

C785

C786

C901

C903

C904

1-165-319-11 CERAMIC CHIP 0.1uF

1-163-251-11 CERAMIC CHIP 100PF

50V

D782

D783

D784

8-719-970-02 DIODE 1SR139-400

8-719-422-64 DIODE MA8062-M

C906

C907

C908

C909

C910

1-163-009-11 CERAMIC CHIP 0.001uF 10%

50V

< IC >

1-163-251-11 CERAMIC CHIP 100PF

1-163-181-00 CERAMIC CHIP 100PF

1-163-251-11 CERAMIC CHIP 100PF

IC301 8-752-079-78 IC CXA2509AQ-T4

IC331 8-759-443-67 IC LC75373ED

IC351 8-759-395-97 IC MM1322XFBE

IC501 8-759-493-99 IC uPD17707GC-529-3B9

IC551 8-759-363-81 IC XC61AN4002PR

C911

C912

C913

C914

1-163-181-00 CERAMIC CHIP 100PF

1-164-182-11 CERAMIC CHIP 0.0033uF 10%

1-164-004-11 CERAMIC CHIP 0.1uF

50V

25V

10%

IC611 8-759-347-49 IC BA3918-V2

IC751 8-759-490-48 IC HA13158

< CONNECTOR >

< JACK >

CN301 1-766-260-11 CONNECTOR, FFC/FPC (ZIF) 7P

* CN351 1-506-995-11 PIN, CONNECTOR (PC BOARD) 13P

CN701 1-764-422-11 PLUG, CONNECTOR 12P

J561

1-764-808-14 JACK (ANT) (ANT IN)

1-566-822-41 JACK (REMOTE IN)

CN781 1-774-701-11 PIN, CONNECTOR 16P

< CHIP CONDUCTOR >

< CONPOSITION CIRCUIT BLOCK >

JC1

JC2

JC4

1-216-296-00 SHORT

1-216-295-00 SHORT

1-216-296-00 SHORT

CP1

1-519-504-11 GAP, DISCHARGE

– 38 –

MAIN

Ref. No.

Part No.

Description

Remark

Ref. No.

Part No.

Description

Remark

JC151 1-216-296-00 SHORT

JC161 1-216-295-00 SHORT

< RESISTOR >

1-216-049-11 RES, CHIP

1-216-061-00 METAL CHIP

1-249-429-11 CARBON

1-216-081-00 METAL CHIP

1-249-429-11 CARBON

1/10W

1/4W

1/10W

1/4W

JC162 1-216-295-00 SHORT

JC163 1-216-296-00 SHORT

JC251 1-216-296-00 SHORT

JC301 1-216-295-00 SHORT

JC302 1-216-295-00 SHORT

3.3K

10K

22K

10K

R10

R11

1-216-109-00 METAL CHIP

1-247-899-11 CARBON

1-216-180-00 RES, CHIP

1-216-073-00 METAL CHIP

1-249-413-11 CARBON

330K

680K

180

10K

470

1/10W

1/4W

1/8W

1/10W

1/4W

JC303 1-216-295-00 SHORT

JC304 1-216-296-00 SHORT

JC331 1-216-296-00 SHORT

JC351 1-216-295-00 SHORT

JC501 1-216-296-00 SHORT

R12

R13

R14

R21

R22

1-216-073-00 METAL CHIP

1-216-049-11 RES, CHIP

1-216-198-00 RES, CHIP

10K

1/10W

1/8W

JC502 1-216-295-00 SHORT

JC503 1-216-296-00 SHORT

JC504 1-216-296-00 SHORT

JC506 1-216-296-00 SHORT

JC507 1-216-296-00 SHORT

R23

R24

R103

R104

R105

1-216-053-00 METAL CHIP

1-249-421-11 CARBON

1-216-041-00 METAL CHIP

1-216-109-00 METAL CHIP

1-216-077-00 METAL CHIP

1.5K

2.2K

470

330K

15K

1/10W

1/4W

1/10W

JC508 1-216-296-00 SHORT

JC561 1-216-295-00 SHORT

JC581 1-216-296-00 SHORT

JC601 1-216-296-00 SHORT

JC611 1-216-296-00 SHORT

R106

R107

R108

R121

R122

1-216-079-00 METAL CHIP

1-249-429-11 CARBON

1-216-081-00 METAL CHIP

1-216-200-11 RES, CHIP

1-216-081-00 METAL CHIP

18K

10K

22K

1.2K

22K

1/10W

1/4W

1/10W

1/8W

JC751 1-216-296-00 SHORT

JC752 1-216-296-00 SHORT

JC781 1-216-295-00 SHORT

JC902 1-216-295-00 SHORT

JC903 1-216-295-00 SHORT

1/10W

R151

R152

R161

R171

R172

1-216-049-11 RES, CHIP

1-216-089-00 RES, CHIP

1-216-061-00 METAL CHIP

1-216-033-00 METAL CHIP

1-216-073-00 METAL CHIP

1/10W

JC904 1-216-295-00 SHORT

< COIL >

47K

3.3K

220

10K

L501

L781

L901

1-410-509-11 INDUCTOR

1-411-669-12 COIL, CHOKE

1-410-509-11 INDUCTOR

10uH

R173

R174

R175

R181

R182

1-216-081-00 METAL CHIP

1-216-129-00 METAL CHIP

1-216-089-00 RES, CHIP

1-216-033-00 METAL CHIP

1-216-073-00 METAL CHIP

22K

2.2M

47K

220

1/10W

< TRANSISTOR >

10K

Q21

Q22

Q171

Q181

Q271

8-729-120-28 TRANSISTOR 2SC1623-L5L6

8-729-021-94 TRANSISTOR 2SK1657-T1B

8-729-920-21 TRANSISTOR DTC314TKH04

R183

R184

R185

R186

R191

1-216-081-00 METAL CHIP

1-216-129-00 METAL CHIP

1-216-089-00 RES, CHIP

1-216-182-00 RES, CHIP

1-216-073-00 METAL CHIP

22K

2.2M

47K

220

1/10W

1/8W

10K

1/10W

Q281

Q351

Q352

Q353

Q354

8-729-920-21 TRANSISTOR DTC314TKH04

8-729-015-11 TRANSISTOR 2SD1802FAST-TL

8-729-027-23 TRANSISTOR DTA114EKA-T146

8-729-900-53 TRANSISTOR DTC114EK

8-729-106-60 TRANSISTOR 2SB1115A

R192

R203

R204

R205

R206

1-216-097-00 RES, CHIP

1-216-041-00 METAL CHIP

1-216-109-00 METAL CHIP

1-216-077-00 METAL CHIP

1-216-079-00 METAL CHIP

100K

470

330K

15K

1/10W

18K

Q355

Q551

Q571

Q581

Q582

8-729-900-53 TRANSISTOR DTC114EK

8-729-027-23 TRANSISTOR DTA114EKA-T146

8-729-120-28 TRANSISTOR 2SC1623-L5L6

8-729-900-53 TRANSISTOR DTC114EK

1-801-806-11 TRANSISTOR DTC144EKA-T146

R207

R208

R251

R252

R261

1-216-222-00 RES, CHIP

1-216-081-00 METAL CHIP

1-216-049-11 RES, CHIP

1-216-089-00 RES, CHIP

1-216-061-00 METAL CHIP

10K

22K

47K

3.3K

1/8W

1/10W

Q583

Q601

Q602

Q603

Q621

8-729-027-38 TRANSISTOR DTA144EKA-T146

8-729-423-99 TRANSISTOR 2SD2137-OP

8-729-900-53 TRANSISTOR DTC114EK

8-729-027-23 TRANSISTOR DTA114EKA-T146

R271

R272

R273

R274

R275

1-216-033-00 METAL CHIP

1-216-073-00 METAL CHIP

1-216-081-00 METAL CHIP

1-216-129-00 METAL CHIP

1-216-089-00 RES, CHIP

220

1/10W

10K

22K

2.2M

47K

Q622

8-729-120-28 TRANSISTOR 2SC1623-L5L6

R281

1-216-033-00 METAL CHIP

220

1/10W

– 39 –

MAIN

Ref. No.

R561

Part No.

Description

Remark

Ref. No.

Part No.

Description

Remark

R282

R283

R284

R285

1-216-073-00 METAL CHIP

1-216-081-00 METAL CHIP

1-216-129-00 METAL CHIP

1-216-089-00 RES, CHIP

10K

22K

2.2M

47K

1/10W

1-208-806-11 RES, CHIP

10K

0.50% 1/10W

R562

R563

R564

R571

R572

1-208-806-11 RES, CHIP

1-216-025-00 RES, CHIP

1-216-097-00 RES, CHIP

1-216-089-00 RES, CHIP

10K

100

100K

47K

0.50% 1/10W

1/10W

R286

R301

R302

R303

R304

1-216-033-00 METAL CHIP

1-216-079-00 METAL CHIP

1-216-097-00 RES, CHIP

1-216-065-00 METAL CHIP

1-216-077-00 METAL CHIP

220

1/10W

18K

100K

4.7K

15K

R573

R574

R575

R585

R586

1-216-089-00 RES, CHIP

1-249-421-11 CARBON

1-216-073-00 METAL CHIP

1-216-113-00 METAL CHIP

1-216-073-00 METAL CHIP

47K

2.2K

10K

470K

10K

1/10W

1/4W

1/10W

R305

R306

R307

R308

R331

1-249-429-11 CARBON

1-216-073-00 METAL CHIP

1-216-105-00 RES, CHIP

1-249-393-11 CARBON

10K

220K

1/4W

1/10W

1/4W

R601

R602

R603

R621

R701

1-249-393-11 CARBON

1-249-395-11 CARBON

1-216-186-00 RES, CHIP

1-216-065-00 METAL CHIP

1-216-025-00 RES, CHIP

330

4.7K

100

1/4W

1/8W

1/10W

R351

R352

R353

R354

R501

1-216-049-11 RES, CHIP

1-249-385-11 CARBON

1-216-065-00 METAL CHIP

1-216-073-00 METAL CHIP

1-216-097-00 RES, CHIP

2.2

4.7K

10K

100K

1/10W

1/6W

1/10W

R702

R703

R704

R705

R706

1-216-025-00 RES, CHIP

1-216-057-00 METAL CHIP

1-216-206-00 RES, CHIP

100

1/10W

1/8W

2.2K

R502

R503

R504

R505

R506

1-216-097-00 RES, CHIP

1-216-057-00 METAL CHIP

100K

2.2K

1/10W

R707

R708

R709

R710

R721

1-216-049-11 RES, CHIP

1-208-806-11 RES, CHIP

1-216-025-00 RES, CHIP

1-216-296-00 SHORT

1/10W

0.50% 1/10W

10K

100

R507

R508

R509

R510

R513

1-216-057-00 METAL CHIP

1-216-073-00 METAL CHIP

1-249-429-11 CARBON

2.2K

10K

100K

1/10W

1/4W

1/10W

R722

R723

R724

R731

R732

1-216-296-00 SHORT

1-216-699-11 METAL CHIP

0.5% 1/10W

R514

R516

R517

R518

R520

1-216-699-11 METAL CHIP

1-216-097-00 RES, CHIP

100K

0.5% 1/10W

1/10W

R733

R734

R751

R752

R781

1-216-296-00 SHORT

1-216-198-00 RES, CHIP

1-216-049-11 RES, CHIP

1/8W

1/10W

R522

R523

R524

R525

R526

1-216-097-00 RES, CHIP

100K

1/10W

< TUNER >

TU1

A-3282-031-A TUNER UNIT TUX-006/2 (EE)

< SWITCH >

R527

R528

R530

R532

R534

1-216-097-00 RES, CHIP

100K

1/10W

S501

S551

1-571-478-11 SWITCH, SLIDE (POWER SELECT)

1-692-431-21 SWITCH, TACTILE (RESET)

R535

R536

R537

R538

R539

1-216-097-00 RES, CHIP

1-216-246-00 RES, CHIP

1-216-097-00 RES, CHIP

100K

1/10W

1/8W

1/10W

< VIBRATOR >

X501

1-567-713-11 VIBRATOR, CRYSTAL (4.5MHz)

************************************************************

MISCELLANEOUS

R540

R541

R542

R543

R544

1-249-421-11 CARBON

1-216-057-00 METAL CHIP

2.2K

1/4W

1/10W

***************

F781

1-776-207-41 CORD (WITH CONNECTOR) (POWER)

1-532-877-11 FUSE (BLADE TYPE) (AUTO FUSE) (10A)

HP901 1-500-157-21 HEAD, MAGNETIC (PLAYBACK)

M901 A-3291-665-A MOTOR ASSY, MAIN (CAPSTAN/REEL)

************************************************************

R545

R546

R551

R552

1-249-429-11 CARBON

1-249-413-11 CARBON

1-216-097-00 RES, CHIP

1-216-057-00 METAL CHIP

10K

470

100K

2.2K

1/4W

1/10W

– 40 –

Ref. No.

Part No.

Description

Remark

**************

HARDWARE LIST

**************

7-621-772-10 SCREW +B 2X4

7-685-793-09 SCREW +PTT 2.6X8 (S)

7-685-792-09 SCREW +PTT 2.6X6 (S)

7-685-794-09 SCREW +PTT 2.6X10 (S)

7-685-106-19 SCREW +P 2X10 TYPE2 NON-SLIT

7-624-104-04 STOP RING 2.0, TYPE-E

7-627-553-17 PRECISION SCREW +P 2X2 TYPE 3

************************************************************

ACCESSORIES & PACKING MATERIALS

********************************

1-473-067-71 REMOTE COMMANDER (RM-X4S)

3-861-693-11 MANUAL, INSTRUCTION

(HUNGARIAN, RUSSIAN)

3-861-694-11 MANUAL, INSTRUCTION, INSTALL

(HUNGARIAN, RUSSIAN)

3-921-278-01 LABEL (DSPL) (for RM-X4S)

X-3373-412-1 CASE (PANEL) ASSY (for FRONT PANEL)

************************************************************

PARTS FOR INSTALLATION AND CONNECTIONS

***************************************

501

502

503

504

505

3-916-161-31 FRAME ASSY

X-3370-077-1 SCREW ASSY (AE. KEY), FITTING

X-3371-913-1 SCREW ASSY (J)

X-3373-432-1 BRACKET ASSY (For RM-X4S)

1-776-207-41 CORD (WITH CONNECTOR) (POWER)

502

501

503

504

505

– 41 –

XR-4803

Sony Corporation

Personal & Mobile Communication Company

– 42 –

98A05076-1

Published by Quality Assurance Dept.

9-925-681-11

Westcott 1879 User Manual
West Bend Back to Basics 4000 User Manual
Sony XR L500X User Manual
Sony DCR TRV116E User Manual
Sony CFDS350SILVER User Manual
Sony Car Video System sdm s93 User Manual
Sony Camcorder TRV21 User Manual
Sony Camcorder CD TRV315 User Manual
Sennheiser Car Satellite Radio System EK 2000 IEM BW User Manual
Russell Hobbs HD4426 User Manual