©ꢀ2012ꢀSonyꢀCorporation
PrintedꢀinꢀChina
4‑421‑770‑11(2)
InꢀtheꢀBox
US
Network Media Player
Remote control
(Remote) (1)
AC power cord (1)
HDMI cable (1)
(NSZ‑GX70 only)
Quick Setup Guide (1)
Getting Started (1)
Reference Guide and
other documents
Quick Setup Guide
Size AA batteries (2)
Toꢀinsertꢀbatteriesꢀintoꢀtheꢀ
remoteꢀcontrol
What’s this?
IR (infrared)
Blaster
cable (1)
The IR Blaster enables you to control
connected devices with your remote.
Please see “To control connected
devices using the remote” shown below
for more information.
Sony Customer Support
NetworkꢀMediaꢀPlayer
NSZ-GS7/NSZ-GX70
Please Do Not Return the Product to the Store
(NSZ-GX70ꢀisꢀonlyꢀforꢀtheꢀUS)
Connection
step
Connect to your TV
Follow : A to connect to your TV directly.
: B to connect to your TV via AV Receiver
: C if your connection differs from the diagrams below.
1
A
Direct to TV
B
To TV via AV Receiver
C
Other connection
See Help Guide for other connection patterns.
HDMIꢀcableꢀ
FromꢀyourꢀPC
(suppliedꢀwithꢀNSZ-GX70ꢀonly)
AV Receiver
HDMIꢀcableꢀ
(suppliedꢀwithꢀNSZ-GX70ꢀonly)
TV
TV
Fromꢀyourꢀsmartphoneꢀ
(optional)
(optional)
HDMIꢀcableꢀ(notꢀsupplied)
HDMIꢀcableꢀ(notꢀsupplied)
Set Top Box /
Digital Video Recorder
Set Top Box /
Digital Video Recorder
step
step
step
Prepare for Network
connection
Connect to the power
source
Start the Initial Setup
Wizard
2 3 4
ACꢀpowerꢀcord
Follow the directions for the Initial Setup
displayed on screen.
Connect to the power
source
Change the TV input
–The screen may stay dark for several seconds after the
Sony logo appears, then the Initial Setup screen appears.
Switch the input selector on the TV
so that the signal from the player
appears on your TV screen.
Then, a screen that shows how to
setup your remote appears.
–When the Initial Setup screen (on which a picture of
a player and a hand holding a remote is displayed)
appears, press and hold (Enter) to pair your remote
with the player.
Wireless LAN
router*1*2
Broadband
router*2
–Complete the Network setup process, otherwise the Initial
Setup Wizard cannot be closed.
Note
LANꢀcableꢀ(notꢀsupplied)
This will only appear the first time you setup your
player.
–It takes about 15 minutes to complete the Initial Setup.
*1 When using wireless connection, you need to set the Network Setup in the Initial Setup Wizard (on step 4).
*2 You can find MAC address in the Initial Setup Wizard (step 4) as needed. Select “Explain step” on “Connect to the Internet” screen.
Toꢀcontrolꢀconnectedꢀdevicesꢀusingꢀtheꢀremote
This player is equipped with a built‑in IR Blaster that accepts remote commands and sends them to various connected devices to control them with your remote. This function works when the player is turned on.
When you set the player close to a connected device (as illustrated on the
right), you can control the device using the remote, including operations such as
adjusting the volume of the TV or an AV Receiver.
However, if you place the player in a location where IR signals cannot reach,
you cannot control connected devices with the built‑in IR Blaster. In this case,
connect the supplied IR Blaster as follows:
*
IRꢀBlaster
Connect the IR Blaster cable to the player.
Place the IR Blaster so that the infrared transmitter points to the IR receiver
(sensor) on the device you want to control, as illustrated on the right.
* Location of the IR receiver may vary depending on the product you are using.
|