Sony CDX 1000RF User Manual

3-045-044-11 (1)  
Location of controls  
Operation  
Additional Information  
Lo ca t in g a sp e cific t ra ck  
No t e s o n d iscs  
Listening to a CD  
Automatic Music Sensor (AMS)  
Precautions  
• This unit cannot be used with a car audio  
without an FM tuner.  
• If your car was parked in direct sunlight  
resulting in a considerable rise in temperature  
inside the car, allow the unit to cool off before  
operating it.  
• If no power is being supplied to the unit,  
check the connections first. If everything is in  
order, check the fuse.  
If you use the discs explained below, the sticky  
residue can cause the CD to stop spinning and  
may cause malfunction or ruin your discs.  
During CD playback, press either side of  
(AMS) for each track you w ant to skip.  
AMS  
1 Adjust the selected transmitting frequency  
AMS  
w ith an FM tuner.  
SHUF  
REPEAT  
DSPL  
OFF  
Do not use second-hand or rental CDs that have  
a sticky residue on the surface (for example from  
peeled-off stickers or from ink, or glue leaking  
from under the stickers.  
(88.3 MHz/88.5 MHz/88.7 MHz/88.9 MHz/  
89.1 MHz/89.3 MHz/89.5 MHz/89.7 MHz/  
89.9 MHz)  
To locate preceding  
tracks  
To locate succeeding  
tracks  
Co m p a ct Disc  
Pla ye r  
2 Insert a CD.  
There are paste residue  
Ink is sticky  
Playback starts automatically.  
Connecting this unit may cause some car  
battery wear when your car has no ACC  
(accessory) position on the ignition key switch.  
Lo ca t in g a sp e cific p o in t in a t ra ck  
— Manual Search  
Label side up  
Do not use rental CDs with old labels that are  
beginning to peel off.  
During playback, press and hold either  
side of (AMS) for about tw o seconds.  
Release w hen you have found the desired  
point.  
1 AMS (Automatic Music Sensor) .  
6 Reset button  
7 Display w indow  
If you have any questions or problems  
concerning your unit that are not covered in this  
manual, please consult your nearest Sony dealer.  
button  
Stickers that are beginning  
to peel aw ay, leaving a  
sticky residue  
2 AMS (Automatic Music Sensor) >  
Operating Instructions  
8 SHUF (shuffle play) button  
9 REPEAT (repeat play) button  
0 DSPL (display mode change) button  
qa OFF button  
button  
AMS  
No t e s o n h a n d lin g CDs  
3 Disc insertion slot  
A dirty or defective disc may cause sound  
dropouts while playing. To enjoy optimum  
sound, handle the disc by its edge. To keep the  
disc clean, do not touch the surface.  
Do not use your CDs with labels or stickers  
attached.  
4 Z (eject) button  
If a CD is already inserted, press u to start  
playback.  
5 u (play/pause) button  
If pressed during playback, the CD will  
pause. If pressed again, playback will  
continue.  
To search backw ard  
To search forw ard  
Labels are attached  
Note  
If “  
Elapsed playing time  
or “  
appears in the display,  
you have reached the beginning or the end of the  
disc and you cannot go any further.  
Note  
No t e s o n CD-R d iscs  
To play back an 8 cm (3 in.) CD, use the optional  
Sony compact disc single adapter (CSA-8).  
You can play CD-Rs (recordable CDs) on this  
unit. However depending on the conditions of  
the recording equipment or the CD-R disc  
itself, some CD-Rs cannot be played on this  
unit.  
You cannot play a CD-R that is not finalized  
(Finalization is necessary for a recorded CD-R  
disc to be played on the audio CD player).  
You cannot play CD-RWs (rewritable CDs) on  
this player.  
Do not stick paper or tape on the labeled  
surface.  
3 Adjust the volume w ith the volume  
control on the car audio.  
Playing a CD in various  
modes  
Pla yin g t ra cks re p e a t e d ly  
Repeat Play  
Getting Started  
To  
Press  
Owners Record  
Stop playback  
Eject the CD  
Z or (OFF)  
Z
The model and serial numbers are located on the bottom of the unit.  
Record the serial number in the space provided below.  
Refer to these numbers whenever you call upon your Sony dealer regarding this  
product.  
Do not expose the discs to direct sunlight or heat  
sources such as hot air-ducts, or leave them in a  
car parked in direct sunlight where there can be  
a considerable rise in temperature inside the car.  
Resetting the unit  
Before operating the unit for the first time or after replacing the car battery, you must reset the unit.  
Press the reset button with a pointed object, such as a ball-point pen.  
Press (REPEAT) during playback.  
“REP” appears in the display.  
Wh e n yo u p la y 8 cm (3 in .) CDs  
Notes  
Use the optional Sony compact disc single  
adapter (CSA-8) to protect the CD player from  
damage.  
Be sure to press (OFF) to turn this unit off when  
When the current track is over, it will play again  
from the beginning.  
Model No. CDX-1000RF Serial No.  
you want to listen to FM radio.  
When CD playback is stopped, you may hear some  
noise from the speakers. To prevent this from  
happening, turn the volume down before stopping  
CD playback.  
If you leave the ejected disc in the disc insertion  
slot after you have pressed Z, the disc will  
automatically retract into the unit after about 15  
seconds in order to protect it.  
AMS  
SHUF  
REPEAT  
DSPL  
OFF  
To return to normal playback mode, press again.  
No t e s o n m o ist u re co n d e n sa t io n  
Pla yin g t ra cks in ra n d o m o rd e r  
— Shuffle Play  
On a rainy day or in a very damp area, moisture  
may condense on the lenses inside the CD  
player. Should this occur, the unit will not  
operate properly. In this case, remove the disc  
and wait for about an hour until the moisture  
evaporates.  
Reset button  
Notes  
Press (SHUF) during playback.  
“SHUF” appears in the display.  
Pressing the reset button will erase the clock setting and some memorized program and memory functions.  
When you connect the power supply cord to the unit or reset the unit, wait for about 10 seconds before you  
insert a disc. If you insert a disc within these 10 seconds, the unit will not be reset, and you will have to press  
the reset button again.  
Before playing, clean the discs with a  
commercially available cleaning cloth. Wipe  
each disc from the center out.  
Do not use solvents such as benzine, thinner,  
commercially available cleaners, or antistatic  
spray intended for analog discs.  
CDX-1000RF  
Sony Corporation 2000 Printed in Korea  
To return to normal playback mode, press again.  
Ch a n g in g t h e d isp la y it e m  
Each time you press (DSPL) during CD  
playback, the item changes as follows:  
Elapsed playing time b B Track number  
Maintenance  
Changing the transmitting  
frequency  
Because this unit processes CD playback sound  
through an FM tuner, there may be interference  
noise during CD playback. In this case, change  
the frequency of the modulated RF signal  
transmitted from the unit. The initial setting is  
88.3 MHz.  
Changing the output level  
You can select the output level of the CD player.  
Normally the initial output level is adequate;  
change the level if necessary.  
Fu se re p la ce m e n t  
When replacing the fuse, be sure to use one  
matching the amperage rating stated on the  
original fuse. If the fuse blows, check the power  
connection and replace the fuse. If the fuse  
blows again after replacement, there may be an  
internal malfunction. In such a case, consult  
your nearest Sony dealer.  
Warning  
Welcome !  
Thank you for purchasing the Sony Compact  
Disc Player. This unit lets you enjoy a variety of  
features.  
This equipment has been tested and found to  
comply with the limits for a Class B digital  
device, pursuant to Part 15 of the FCC Rules.  
These limits are designed to provide reasonable  
protection against harmful interference in a  
residential installation. This equipment  
generates, uses, and can radiate radio frequency  
energy and, if not installed and used in  
accordance with the instructions, may cause  
harmful interference to radio communications.  
However, there is no guarantee that interference  
will not occur in a particular installation. If this  
equipment does cause harmful interference to  
radio or television reception, which can be  
determined by turning the equipment off and  
on, the user is encouraged to try to correct the  
interference by one or more of the following  
measures:  
1 Press (REPEAT) for tw o seconds.  
2 Press (REPEAT) again.  
Wa rn in g  
Initial setting  
1 Press (REPEAT) for tw o seconds until  
Never use a fuse with an amperage rating  
exceeding the one supplied with the unit as this  
could damage the unit.  
Features  
Easy connection to any car audio with an FM  
tuner  
Dashboard installation for easy CD disc  
changing  
8X digital sampling filter for clear CD audio  
Quick recovery function to minimize  
disturbance from skips  
Repeat play function for playing tracks  
repeatedly  
Shuffle play fucnion for playing tracks in  
random order  
frequency appears.  
3 Press either the left or right side of (AMS)  
to select the output level.  
2 Press either the left or right side of (AMS)  
to select the frequency.  
To decrease the output level  
Each time you press (AMS), the frequency  
changes as follows:  
. : ,  
Troubleshooting guide  
The following checklist will help you remedy the problems you may encounter with your unit.  
Before going through the checklist below, check the connection and operating procedures.  
Specifications  
AUDIO POWER SPECIFICATIONS  
> : 88.3 MHz t 88.5 MHz t 88.7 MHz t  
88.9 MHz t 89.1 MHz t 89.3 MHz t  
89.5 MHz t 89.7 MHz t 89.9 MHz t  
. : 88.3 MHz t 89.9 MHz t 89.7 MHz t  
89.5 MHz t 89.3 MHz t 89.1 MHz t  
88.9 MHz t88.7 MHz t 88.5 MHz t  
To increase the output level  
> : ,  
POWER OUTPUT AND TOTAL HARMONIC DISTORTION  
13 watts per channel minimum continuous average power into  
4 ohms, 4 channels driven from 20 Hz to 20 kHz with no more than  
1 % total harmonic distortion.  
— Reorient or relocate the receiving antenna.  
— Increase the separation between the  
equipment and receiver.  
— Connect the equipment into an outlet on a  
circuit different from that to which the  
receiver is connected.  
Pro b le m  
Ca u se /So lu t io n  
4 Press (REPEAT) for more than tw o  
CD cannot be loaded.  
Another CD is already loaded.  
The CD was forcibly inserted upside down.  
seconds.  
3
Press (REPEAT) for more than tw o seconds.  
Play does not begin.  
CD is automatically ejected.  
CD w ill not eject.  
Dirty disc.  
Note  
— Consult the dealer or an experienced radio/  
TV technician for help.  
Be sure to set the frequency of your FM tuner to the  
newly selected frequency.  
The ambient temperature exceeds 50°C (122°F).  
Press the Z button for two seconds.  
Press the reset button.  
Ot h e r sp e cifica t io n s  
CD p la ye r se ct io n  
Ge n e ra l  
Outputs  
Power requirements  
You are cautioned that any changes or  
modifications not expressly approved in this  
manual could void your authority to operate  
this equipment.  
The operation buttons do not  
function.  
System  
Compact disc digital audio  
system  
Line output  
12 V DC car battery  
(negative ground)  
2 A (at disc loading)  
Approx. 178 × 50 × 173 mm  
(7 1/8 × 2 × 6 7/8 in.)  
(w/h/d)  
Signal-to-noise ratio  
Frequency response  
Wow and flutter  
Laser Diode Properties  
Material  
Wavelength  
Emission Duration  
Laser output power  
90 dB  
The unit is installed at an angle of more than 60°.  
The unit is not installed in a sturdy part of the car.  
The sound skips due to  
vibration.  
10 – 20,000 Hz  
Below measurable limit  
Current drain  
Dimensions  
CAUTION  
GaAs + GaAlAs  
785 ~ 815 nm (Typ.800 nm)  
Continuous  
Mounting dimensions  
Approx. 182 × 53 × 159 mm  
(7 1/4 × 2 1/8 × 6 3/8 in.)  
(w/h/d)  
Approx. 1.1 kg (2 lb. 7 oz.)  
Parts for installation and  
connections (1 set)  
Compact disc single adapter  
CSA-8  
The use of optical instruments with this product  
will increase eye hazard.  
Erro r d isp la ys  
The following indications will flash for about five seconds.  
Less than 0.5 mW*  
Mass  
Supplied accessories  
* This output is the value measured at a distance of  
0.7 mm from the objective lens surface on the  
Optical Pick-up Block.  
Disp la y  
Ca u se  
So lu t io n  
A CD is dirty or inserted upside  
down.  
Clean or insert the CD correctly.  
Optional accessories  
Rotary commander  
RM-X4S  
The CD player cannot be operated  
because of some problem.  
Press the reset button or Z.  
Source selector  
XA-107  
BUS cable (supplied with an  
RCA pin cord)  
RC-61 (1 m), RC-62 (2 m)  
If the above-mentioned solutions do not help improve the situation, consult your nearest Sony dealer.  
Design and specifications are subject to change  
without notice.  

VDO Dayton CD 5626 X User Manual
Toshiba MA 1535 2 User Manual
ToCAD Sunpak PRO 624P User Manual
Sony DCR TRV25 User Manual
Sony Camcorder DXC 190 User Manual
SMC Networks TIGERSWITCH SMC6752AL2 User Manual
Sharp Scientific Calculator ELW516XBSL User Manual
Sharp 10 Digit Commercial Printing Calculator EL501WBBK User Manual
Sanyo XACTI VPC SH1PX User Manual
Samsung Camcorder HMX F91 User Manual