Preparing the camera
Before your operation
Shooting images
Using the shooting
function
Using the viewing
function
Changing your setup
Viewing images on a
computer
Printing images
Additional information on this product and
answers to frequently asked questions can be
found at our Customer Support Website.
Digital Single Lens Reflex Camera
Instruction Manual
A-mount
DSLR-A390
Printed using VOC (Volatile Organic
Compound)-free vegetable oil based ink.
®
Owner’s Record
IMPORTANTSAFETY
INSTRUCTIONS
SAVE THESE
The model and serial numbers are located
on the bottom.
Record the serial number in the space
provided below.
Refer to these numbers whenever you call
upon your Sony dealer regarding this
product.
Model No. DSLR-A390
Serial No. __________________________
INSTRUCTIONS.
DANGER - TO
REDUCE THE RISK
OF FIRE OR
WARNING
To reduce fire or shock hazard, do
not expose the unit to rain or
moisture.
ELECTRIC SHOCK,
CAREFULLY
FOLLOW THESE
INSTRUCTIONS.
If the shape of the plug does not fit the
power outlet, use an attachment plug
adaptor of the proper configuration for the
power outlet.
Caution
Battery pack
If the battery pack is mishandled, the
battery pack can burst, cause a fire or even
chemical burns. Observe the following
cautions.
• Do not disassemble.
• Do not crush and do not expose the
battery pack to any shock or force such as
hammering, dropping or stepping on it.
• Do not short circuit and do not allow
metal objects to come into contact with
the battery terminals.
• Do not expose to high temperature above
60°C (140°F) such as in direct sunlight or
in a car parked in the sun.
• Do not incinerate or dispose of in fire.
• Do not handle damaged or leaking
lithium ion batteries.
• Be sure to charge the battery pack using a
genuine Sony battery charger or a device
that can charge the battery pack.
2
• Keep the battery pack out of the reach of
small children.
• Keep the battery pack dry.
• Replace only with the same or equivalent
type recommended by Sony.
• Dispose of used battery pack promptly
described the instructions.
For Customers in the U.S.A.
UL is an internationally recognized safety
organization.
The UL Mark on the product means it has
been UL Listed.
Battery charger
If you have any questions about this
product, you may call:
Sony Customer Information Services
Center
1-800-222-SONY (7669)
The number below is for the FCC related
matters only.
Even if the CHARGE lamp is not lit, the
battery charger is not disconnected from the
AC power source (mains) as long as it is
connected to the wall outlet (wall socket).
If some trouble occurs while using the
battery charger, immediately shut off the
power by disconnecting the plug from the
wall outlet (wall socket).
Regulatory Information
Declaration of Conformity
Trade Name: SONY
Model No.: DSLR-A390
Responsible Party: Sony Electronics
Inc.
Address:16530 Via Esprillo,
San Diego, CA 92127 U.S.A.
Telephone No.: 858-942-2230
For Customers in the U.S.A.
and Canada
RECYCLING LITHIUM-ION
BATTERIES
Lithium-Ion batteries are
recyclable.
You can help preserve
our environment by
returning your used
rechargeable batteries to
the collection and
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) This
device may not cause harmful
interference, and (2) this device must
accept any interference received,
including interference that may cause
undesired operation.
recycling location nearest you.
For more information regarding recycling
of rechargeable batteries, call toll free
1-800-822-8837, or visit http://
www.rbrc.org/
CAUTION
Caution: Do not handle damaged or
leaking Lithium-Ion batteries.
You are cautioned that any changes or
modifications not expressly approved in
this manual could void your authority to
operate this equipment.
Battery pack
This device complies with Part 15 of the
FCC Rules, Operation is subject to the
following two conditions:
(1) This device may not cause harmful
interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
This Class B digital apparatus complies
with Canadian ICES-003.
3
Note:
For Customers in Europe
Notice for the customers in the
This equipment has been tested and found
to comply with the limits for a Class B
digital device, pursuant to Part 15 of the
FCC Rules.
countries applying EU Directives
The manufacturer of this product is Sony
Corporation, 1-7-1 Konan Minato-ku
Tokyo, 108-0075 Japan. The Authorized
Representative for EMC and product safety
is Sony Deutschland GmbH, Hedelfinger
Strasse 61, 70327 Stuttgart, Germany. For
any service or guarantee matters please
refer to the addresses given in separate
service or guarantee documents.
These limits are designed to provide
reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses, and can
radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does cause
harmful interference to radio or television
reception, which can be determined by
turning the equipment off and on, the user
is encouraged to try to correct the
interference by one or more of the
following measures:
– Reorient or relocate the receiving
antenna.
– Increase the separation between the
equipment and receiver.
– Connect the equipment into an outlet
on a circuit different from that to which
the receiver is connected.
– Consult the dealer or an experienced
radio/TV technician for help.
This product has been tested and found
compliant with the limits set out in the
EMC Directive for using connection cables
shorter than 3 meters (9.8 feet).
Attention
The electromagnetic fields at the specific
frequencies may influence the picture and
sound of this unit.
Notice
If static electricity or electromagnetism
causes data transfer to discontinue midway
(fail), restart the application or disconnect
and connect the communication cable
(USB, etc.) again.
The supplied interface cable must be used
with the equipment in order to comply with
the limits for a digital device pursuant to
Subpart B of Part 15 of FCC Rules.
4
Disposal of Old Electrical &
Electronic Equipment (Applicable in
the European Union and other
European countries with separate
collection systems)
Disposal of waste batteries
(applicable in the European Union
and other European countries with
separate collection systems)
This symbol on the battery or on the
packaging indicates that the battery
provided with this product shall not be
treated as household waste.
On certain batteries this symbol might be
used in combination with a chemical
symbol. The chemical symbols for mercury
(Hg) or lead (Pb) are added if the battery
contains more than 0.0005% mercury or
0.004% lead.
By ensuring these batteries are disposed of
correctly, you will help prevent potentially
negative consequences for the environment
and human health which could otherwise be
caused by inappropriate waste handling of
the battery. The recycling of the materials
will help to conserve natural resources.
In case of products that for safety,
performance or data integrity reasons
require a permanent connection with an
incorporated battery, this battery should be
replaced by qualified service staff only.
To ensure that the battery will be treated
properly, hand over the product at end-of-
life to the applicable collection point for the
recycling of electrical and electronic
equipment.
This symbol on the product or on its
packaging indicates that this product shall
not be treated as household waste. Instead it
shall be handed over to the applicable
collection point for the recycling of
electrical and electronic equipment. By
ensuring this product is disposed of
correctly, you will help prevent potential
negative consequences for the environment
and human health, which could otherwise
be caused by inappropriate waste handling
of this product. The recycling of materials
will help to conserve natural resources. For
more detailed information about recycling
of this product, please contact your local
Civic Office, your household waste
disposal service or the shop where you
purchased the product.
For all other batteries, please view the
section on how to remove the battery from
the product safely. Hand the battery over to
the applicable collection point for the
recycling of waste batteries.
For more detailed information about
recycling of this product or battery, please
contact your local Civic Office, your
household waste disposal service or the
shop where you purchased the product.
5
Notice for customers in the
United Kingdom
A moulded plug complying with BS 1363
is fitted to this equipment for your safety
and convenience.
Should the fuse in the plug supplied need to
be replaced, a fuse of the same rating as the
supplied one and approved by ASTA or
BSI to BS 1362, (i.e., marked with an
mark) must be used.
or
If the plug supplied with this equipment has
a detachable fuse cover, be sure to attach
the fuse cover after you change the fuse.
Never use the plug without the fuse cover.
If you should lose the fuse cover, please
contact your nearest Sony service station.
6
Notes on using your camera
effect by using the “Pixel mapping”
function (page 156).
Shooting procedure
• This camera has two modes for shooting:
the Live View mode using the LCD
monitor, and the viewfinder mode using
the viewfinder (OVF).
• There may be differences between an
image recorded in Live View mode and
an image recorded in viewfinder mode,
such as exposure, white balance, or D-
range optimizer, depending on the
method used of metering or the exposure
mode.
Black, white, red,
blue and green
points
• In Live View mode, the recorded image
may be different from the image you
monitored with the LCD monitor. The
difference becomes larger in the
following or other cases:
– When firing the flash.
– When shooting a low-intensity subject,
such as night scenery.
• Do not hold the camera by taking hold of
the LCD monitor.
• Do not expose the camera to direct
sunlight. If sunlight is focused on a
nearby object, it may cause a fire. When
you must place the camera under direct
sunlight, attach the lens cap.
– When the difference of the intensity of
a subject is too large.
– When attaching a Circular PL Filter.
• Images may trail across on the LCD
monitor in a cold location. This is not a
malfunction. When turning on the camera
in a cold location, the LCD monitor may
become temporarily dark. When the
camera warms up, the monitor will
function normally.
• Do not press against the LCD monitor.
The monitor may be discolored and that
may cause a malfunction.
No compensation for contents of the
recording
The contents of the recording cannot be
compensated for if recording or playback is
not possible due to a malfunction of your
camera or a memory card, etc.
Warning on copyright
Back up recommendation
To avoid the potential risk of data loss,
always copy (back up) data to other
medium.
Television programs, films, videotapes, and
other materials may be copyrighted.
Unauthorized recording of such materials
may be contrary to the provisions of the
copyright laws.
Notes on the LCD monitor and lens
• The LCD monitor is manufactured using
extremely high-precision technology so
over 99.99% of the pixels are operational
for effective use. However, there may be
some tiny black points and/or bright
points (white, red, blue or green in color)
that constantly appear on the LCD
The pictures used in this manual
The photographs used as examples of
pictures in this manual are reproduced
images, and are not actual images shot
using this camera.
monitor. These points are normal in the
manufacturing process and do not affect
the images in any way.
To deal with such issues that may appear
in Live View mode, you may reduce the
7
On the data specifications described
in this Instruction Manual
The data on performance and specifications
is defined under the following conditions,
except as described in this Instruction
Manual: at an ordinary ambient
temperature of 25ºC (77°F), and using a
fully charged battery pack.
8
Table of Contents
/
Shooting with the automatic setting............... 47
Shooting with a suitable setting for the subject (Scene
9
..................................................................................... 56
............................................................................ 68
............................................................................ 69
............................................................................ 77
Adjusting the brightness of the image (Exposure, Flash
............................................................................ 88
10
12
Preparing the camera
Checking the accessories supplied
The number in parentheses indicates the number of pieces.
• BC-VH1 Battery charger (1)
• Body cap (1) (Attached on the
camera)
• Power cord (mains lead) (1) (not
supplied in the U.S.A. and
Canada)
• Eyecup (1) (Attached on the
camera)
• CD-ROM (Application Software
for α camera) (1)
• Quick Start Guide (1)
• Instruction Manual (This manual)
(1)
• Rechargeable battery pack NP-
FH50 (1)
• USB cable (1)
• Shoulder strap (1)
• Eyepiece cover (1)
13
Preparing the battery pack
When using the camera for the first time, be sure to charge the NP-FH50
“InfoLITHIUM” battery pack (supplied).
Charging the battery pack
The “InfoLITHIUM” battery pack can be charged even when it has not
been fully depleted.
It can also be used when it has not been fully charged.
1 Insert the battery pack on the
battery charger.
Push the battery pack until it clicks.
14
For customers in the U.S.A. and
Canada
2 Connect the battery charger to the
wall outlet (wall socket).
Plug
Light on: Charging
Light off: Normal charge completed
One hour after the lamp is turned off: Full
charge completed
To the wall
outlet (wall
socket)
CHARGE lamp
For customers in countries/regions
other than the U.S.A. and Canada
Power cord
(mains lead)
CHARGE lamp
About charging time
• Time required to charge a fully depleted battery pack (supplied) at a
temperature of 25°C (77°F) is as follows.
Full charge
Normal charge
Approx. 265 min.
Approx. 205 min.
• The charging time differs depending on the remaining capacity of the
battery back or charging conditions.
When the CHARGE lamp flashes
• The CHARGE lamp of the supplied battery charger flashes in either way:
– Fast flashing: Turns the light on and off repeatedly at the interval of
0.15 seconds.
– Slow flashing: Turns the light on and off repeatedly at the interval of
1.5 seconds.
15
• When the CHARGE lamp flashes fast, remove the battery pack being
charged, and then insert the same battery pack into the battery charger
securely again. When the CHARGE lamp flashes fast again, this may
indicate a battery error or that a battery pack other than the specified type
has been inserted. Check that the battery pack is the specified type. If the
battery pack is the specified type, remove the battery pack, replace it with
a new one or another one and check if the battery charger operates
correctly. If the battery charger operates correctly, a battery error may
have occurred.
• When the CHARGE lamp flashes slowly, it indicates that the battery
charger stops charging temporarily on standby. The battery charger stops
charging and enters the standby status automatically when the
temperature is outside of the recommended operating temperature. When
the temperature gets back within the appropriate range, the battery
charger resumes charging and the CHARGE lamp lights up again. We
recommend charging the battery pack in an ambient temperature of
between 10°C to 30°C (50°F to 86°F).
Notes
• Connect the battery charger to the nearest wall outlet (wall socket).
• When charging is finished, disconnect the power cord (mains lead) from the wall
outlet (wall socket), and remove the battery pack from the battery charger. If you
leave the charged battery pack on the charger, battery life may be decreased.
• Do not charge any battery pack other than the “InfoLITHIUM” H series battery pack
in the battery charger (supplied) with your camera. Batteries other than the specified
kind may leak, overheat, or explode if you attempt to charge them, posing a risk of
injury from electrocution and burns.
• If the battery charger is dirty, charging may not be performed successfully. Clean the
battery charger with dry cloth, etc.
To use your camera abroad — Power sources
You can use your camera and the battery charger and the AC-PW10AM
AC Adaptor (sold separately) in any country or region where the power
supply is within 100 V to 240 V AC, 50/60 Hz.
Note
• Do not use an electronic transformer (travel converter), as this may cause a
malfunction.
16
Inserting the charged battery pack
1 While sliding the battery cover
open lever, open the battery
cover.
2 Firmly insert the battery pack all
the way while pressing the lock
lever with the tip of the battery.
Lock lever
3 Close the battery cover.
To remove the battery pack
Turn off the camera and slide the lock
lever in the direction of the arrow. Be
careful not to drop the battery pack.
Lock lever
17
To check the remaining battery level
Set the power switch to ON and check the level on the LCD monitor.
“Battery
exhausted”
Battery level
You cannot shoot
any more pictures.
High
Low
What is an “InfoLITHIUM” battery pack?
An “InfoLITHIUM” battery pack is a lithium-ion battery pack that has
functions for exchanging information related to operating conditions with
your camera.
Notes
• The displayed level may not be correct under certain circumstances.
• Do not expose the battery pack to water. The battery pack is not water-resistant.
• Do not leave the battery pack in extremely hot places, such as in a car or under direct
sunlight.
Available battery packs
Only an NP-FH50 battery pack can be used with the camera. Note that the
NP-FH30 and NP-FH40 cannot be used.
Effective use of the battery pack
• Battery performance decreases in low temperature surroundings. So, the
time that the battery pack can be used is shorter in cold places and the
speed of continuous shooting slows down. We recommend that you put
the battery pack in a pocket close to your body to warm it up, and insert it
in your camera immediately before you start shooting.
• The battery pack will run out quickly if you use the flash frequently, use
continuous shooting often, or turn the camera on and off frequently.
• The time available in the Live View mode is shorter than that in the
viewfinder mode. When you feel that the battery consumption is too fast,
switch to the viewfinder mode. Doing so makes the battery last longer.
Battery life
• The battery life is limited. Battery capacity decreases little by little as you
use it more and more, and as time passes. If the battery operating time
seems shortened considerably, a probable cause is that the battery pack
has reached the end of its life. Buy a new battery pack.
18
• The battery life varies according to how it is stored and the operating
conditions and environment in which each battery pack is used.
How to store the battery pack
If the battery pack is not to be used for a long time, fully charge it and then
fully use it up once a year on your camera before storing the battery pack in
a dry, cool place to prolong the battery life.
19
Attaching a lens
1 Remove the body cap from the
camera and the packaging lid
from the rear of the lens.
• When changing the lens, quickly
change the lens away from dusty
locations so as to keep dust or debris
from getting inside the camera.
Body cap
Packaging lid
2 Mount the lens by aligning the
orange index marks on the lens
and camera.
Orange index marks
3 Turn the lens clockwise until it
clicks into the locked position.
Notes
• A rear lens cap is not supplied with the DT 18-55mm F3.5-5.6 SAM Lens Kit. When
you store the lens without attaching it to the camera, purchase the Rear Lens Cap
ALC-R55.
• When attaching a lens, do not press the lens release button.
• Do not use force when attaching a lens.
• E-mount lenses are not compatible with this camera.
20
To remove the lens
1 Press the lens release button all
the way in and turn the lens
counterclockwise until it stops.
Lens release button
2 Replace the packaging lid on the
lens and attach the body cap to
the camera.
• Before you attach them, remove dust
from them.
• When you purchase the DT 18 – 55 mm
F3.5 – 5.6 SAM Lens Kit, purchase the
Rear Lens Cap ALC-R55 also.
Note on changing the lens
When changing the lens, if dust or debris gets inside the camera and lands
on the surface of the image sensor (the part that acts as the film), it may
appear on the image, depending on the shooting environment.
The camera is equipped with an anti-dust function to prevent dust from
landing on the image sensor. However, quickly change the lens away from
dusty locations when attaching/removing a lens.
If dust or debris lands on the image sensor
Clean the image sensor using [Cleaning mode] in the Setup menu
21
Inserting a memory card
Only “Memory Stick PRO Duo” media, “Memory Stick PRO-HG Duo”
media, SD memory cards and SDHC memory cards can be used with this
camera. A MultiMediaCard cannot be used with this camera.
The “Memory Stick PRO Duo” media and “Memory Stick PRO-HG Duo”
media are referred to as the “Memory Stick PRO Duo” media and the SD
memory card and SDHC memory card are referred to as the “SD memory
card” in this Instruction Manual.
1 Open the memory card cover.
Face side (SD memory card)
2 Insert “Memory Stick PRO Duo”
media or an SD memory card.
Terminal part
• Insert the memory card until it clicks as
illustrated.
Face side (“Memory Stick PRO
Duo”)
Terminal part
3 Select the type of memory card
you want to use using the memory
card switch.
22
4 Close the memory card cover.
To remove the memory card
Check that the access lamp is not lit, then
open the memory card cover, and push
the memory card once.
Access lamp
Notes on using memory cards
• Do not strike, bend or drop the memory card.
• Do not use or store the memory card under the following conditions:
– High temperature locations such as the hot interior of a car parked in
direct sunlight.
– Locations exposed to direct sunlight.
– Humid locations or locations with corrosive substances present.
• The memory card may be hot just after it has been used for a long time.
Be careful when you handle it.
• When the access lamp is lit, do not remove the memory card or the
battery pack, or turn off the power. The data may be corrupted.
• Data may be damaged if you place the memory card near strongly-
magnetized material or use the memory card in a static-prone or
electrically noisy environment.
• We recommend backing up important data, such as to a hard disk of a
computer.
• When you carry or store the memory card, put it in the case supplied with
it.
• Do not expose the memory card to water.
• Do not touch the terminal section of the memory card with your hand or a
metal object.
• When the write-protect switch of a memory card is set to the LOCK
position, you cannot perform operations, such as recording or deleting
images.
23
• The “Memory Stick PRO Duo” media with a capacity up to 32 GB or the
SD memory cards with a capacity up to 32 GB have been confirmed to
operate properly with this camera.
• The memory cards formatted with a computer are not guaranteed to
operate with this camera.
• Data read/write speeds differ depending on the combination of the
memory cards and the equipment used.
• Do not press down hard when you write down on the memo area.
• Do not attach a label on the memory cards themselves.
• Do not disassemble or modify the memory cards.
• Do not leave the memory cards within the reach of small children. They
might accidentally swallow it.
Notes on the “Memory Stick” media used with the camera
The types of “Memory Stick” media that can be used with this camera are
listed in the table below. However, proper operation cannot be guaranteed
for all “Memory Stick PRO Duo” media functions.
“Memory Stick PRO Duo”
media*
Available with your camera
“Memory Stick PRO-HG Duo”
media*
“Memory Stick Duo” media
Unavailable with your camera
Unavailable with your camera
“Memory Stick” media and
“Memory Stick PRO” media
* This is equipped with MagicGate function. MagicGate is copyright protection
technology that uses encryption technology. Data recording/playback that requires
MagicGate functions cannot be performed with this camera.
* Supports high-speed data transfer using a parallel interface.
24
Preparing the camera
Setting up the date
When you turn the camera on for the first time, the date/time setup screen
appears.
1 Set the power switch to ON to turn
the camera on.
• To turn the camera off, set it to OFF.
2 Verify that [OK] is selected on the
LCD monitor, then press the
center of the control button.
3 Select each item with b/B and
set the numeric value with v/V.
• When changing the sequence of
[YYYY/MM/DD], first select [YYYY/
MM/DD] with b/B, then change it
with v/V.
4 Repeat step 3 to set other items, then press the center of the
control button.
25
5 Verify that [OK] is selected, then press the center of the control
button.
To cancel the date/time setting operation
Press the MENU button.
To set up the date/time again
MENU button t
2 t [Date/Time setup]
26
Using the accessories supplied
This section describes how to use the shoulder strap, the eyepiece cover,
and eyecup. The other accessories are described in the following pages.
• Rechargeable battery pack (page 14)
• Battery charger (page 14)
• Power cord (mains lead) (not supplied in the U.S.A. and Canada)
• CD-ROM (page 138)
Attaching the shoulder strap
Attach both ends of the strap onto
the camera.
• You can also attach the eyepiece cover
Eyepiece cover
(page 28) on the strap.
27
Using the eyepiece cover and eyecup
You can prevent light from entering through the viewfinder and affecting
the exposure. When the shutter is released without the use of the viewfinder
in viewfinder mode, as in shooting with the self-timer, attach the eyepiece
cover.
1 Tilt the LCD monitor downward.
2 Carefully slide the eyecup off by
pushing on each side of the
eyecup.
• Put your fingers under the eyecup, and
slide it upward.
3 Slide the eyepiece cover over the
viewfinder.
Note
• The eyepiece sensors located below the viewfinder may be activated depending on
the situation, and the focus may be adjusted or the LCD monitor may continue to
28
Checking the number of recordable
images
Once you insert a memory card into the
camera and set the power switch to ON,
the number of images that can be
recorded (should you continue to shoot
using the current settings) is displayed on
the LCD monitor.
Notes
• When “0” (the number of recordable images) flashes in yellow, the memory card is
full. Replace the memory card with another one, or delete images in the current
• When “NO CARD” (the number of recordable images) flashes in yellow, it means
no memory card has been inserted. Insert a memory card.
The number of images that can be recorded on a memory
card
The table shows the approximate number of images that can be recorded on
a memory card formatted with this camera. The values are defined using
Sony standard memory cards for testing. The values may vary depending
on the shooting conditions.
Image size: L 14M
Aspect ratio: 3:2*
“Memory Stick PRO Duo” media
(Units: Images)
Capacity
2GB
4GB
8GB
16GB
32GB
Size
Standard
Fine
548
393
72
1085
779
144
178
2180
1566
291
4421
3176
592
8725
6268
1169
1438
RAW & JPEG
RAW
89
358
728
29
SD memory card
(Units: Images)
Capacity
Size
2GB
4GB
8GB
16GB
32GB
Standard
537
385
71
1081
776
144
177
2177
1564
291
4421
3176
592
8889
6386
1191
1465
Fine
RAW & JPEG
RAW
87
358
728
* When [Aspect ratio] is set to [16:9], you can record more images than the numbers
shown in the table above. However, if it is set to [RAW], the number is the same as
that of the [3:2] aspect ratio.
The number of images that can be recorded using a battery
pack
The approximate number of images that can be recorded is as follows when
you use the camera with the battery pack (supplied) at full capacity.
Note that the actual numbers may be less than those indicated depending on
the conditions of use.
Live View mode
Viewfinder mode
Approx. 230 images
Approx. 500 images
• The number is calculated with a battery pack at full capacity and in the
following situation:
– At an ambient temperature of 25°C (77°F).
– [Quality] is set to [Fine].
– [Autofocus mode] is set to
(Automatic AF).
– Shooting once every 30 seconds.
– The flash strobes once every two times.
– The power turns on and off once every ten times.
• The measurement method is based on the CIPA standard.
(CIPA: Camera & Imaging Products Association)
30
Cleaning
Cleaning the LCD monitor
Wipe the screen surface with a commercially available LCD cleaning kit to
remove fingerprints, dust, etc.
Cleaning the lens
• When cleaning the lens surface, remove dust using a commercially
available blower. In case of dust that sticks to the surface, wipe it off with
a soft cloth or tissue paper slightly moistened with lens cleaning solution.
Wipe in a spiral pattern from the center to the outside. Do not spray lens
cleaning solution directly onto the lens surface.
• Do not touch the inside of the camera, such as lens contacts, or the mirror.
Since dust on the mirror or around the mirror may affect the autofocus
system, blow away dust using a commercially available blower. If dust
lands on the image sensor, it may appear on the photo image. Turn the
not use a spray blower to clean the inside of the camera. Using this may
cause a malfunction.
• Do not use a cleaning solution containing organic solvents, such as
thinner, or benzine.
Cleaning the camera surface
Clean the camera surface with a soft cloth slightly moistened with water,
then wipe the surface with a dry cloth. Do not use the following as they
may damage the finish or the casing.
• Chemical products such as thinner, benzine, alcohol, disposable cloths,
insect repellent, sunscreen or insecticide, etc.
• Do not touch the camera with the above on your hand.
• Do not leave the camera in contact with rubber or vinyl for a long time.
31
Cleaning the image sensor
If dust or debris enters the camera and lands on the image sensor (the part
that acts as the film), it may appear on the photo image, depending on the
shooting environment. If there is dust on the image sensor, use a
commercially available blower and clean the image sensor following the
steps below. You can easily clean the image sensor using only the blower
and the anti-dust function.
Notes
• Cleaning can be performed only when the battery level is
(three remaining
battery icons) or more. Low battery power during cleaning can cause damage to the
shutter. The cleaning should be completed quickly. The use of an AC-PW10AM AC
Adaptor (sold separately) is recommended.
• Do not use a spray blower because it may scatter water droplets inside the camera
body.
2 Press the MENU button, then
select
3 with b/B on the
control button.
MENU button
3 Select [Cleaning mode] with v/V,
then press the center of the
control button.
The message “After cleaning, turn
camera off. Continue?” appears.
4 Select [OK] with v on the control button, and press the center
of the control button.
After the image sensor vibrates for a short time, the mirror in front is lifted.
32
6 Use the blower to clean the image
sensor surface and the
surrounding area.
• Do not touch the image sensor with the
tip of the blower. Complete the
cleaning quickly.
• Hold the camera’s face downward to
prevent the dust from resettling in the
camera.
• When cleaning the image sensor, do not
put the tip of a blower into the cavity
beyond the mount.
7 Attach the lens and turn the camera off.
Note
• The camera starts beeping if the battery pack becomes low during cleaning. Stop
cleaning immediately and turn the camera off.
33
Before your operation
Identifying parts and screen indicators
See the pages in parentheses for details of operation.
Front side
E Lens contacts*
F Remote sensor
G Mirror*
* Do not directly touch these
parts.
H Mount
J
Image sensor position
mark (77)
34
Rear side
M Control button
When the menu is turned on: v/
When the menu is turned off:
(97)/
N
O
(Delete) button (110)
(Playback) button (102)
* Do not directly touch these
parts.
I
(Smart teleconverter)
button (81)
J For shooting:
button (86)
(Exposure)
For viewing:
button (103)
(Zoom in)
Spot AF button (79)
35
Sides/Bottom
B Memory card switch
C Memory card cover
K Tripod receptacle
• Use a tripod with a screw length
of less than 5.5 mm (7/32 inch).
You will be unable to firmly
secure the camera to tripods
having screws longer than 5.5
mm (7/32 inch), and may
D “Memory Stick PRO Duo”
media insertion slot (22)
E SD memory card insertion slot
damage the camera.
F
I DC IN terminal
• When connecting the AC-
PW10AM AC Adaptor (sold
separately) to the camera, turn
the camera off, then plug the
connector of the AC Adaptor to
the DC IN terminal on the
camera.
36
LCD monitor
The indicators on the monitor are displayed as follows in Live View mode.
A
B
Display
Indication
Display
Indication
Remaining battery (18)
Smart teleconverter (81)
Image quality (117)
Drive mode (97)
×1.4
Histogram (87)
Focus mode (78)
ratio (116)
AF area (79)
Memory card (22)
Metering (89)
100
Remaining number of
recordable images (29)
P A S M
White balance (Preset,
Custom, Color
Flash mode (82)
7500K temperature, Color filter)
G9
D-Range Optimizer (94)
Creative Style (94)
Red-eye reduction (84)
Flash compensation (88)
ISO sensitivity (90)
+2.0
ISO 400
37
C
Display
z
Indication
1/125
F3.5
Shutter speed (61)
Aperture (59)
Camera shake warning
SteadyShot scale (45)
To switch the recording information display
Each time you press DISP on the control
button, the screen changes as follows.
Indicators on
Histogram on
Indicators off
Histogram (page 87)
38
Selecting a function/setting
You can select a function for shooting or playback from the menu list. To
display the menu list, press the control button, Fn (Function) button, or
MENU button.
Example: When the Fn button is pressed.
From the menu list, use the control button
to move the cursor to the setting of your
choice and execute the selection.
: Press v/V/b/B on the control
button to move the cursor.
z: Press the center button to execute the
selection.
In this Instruction Manual, the process of selecting a function with the
control button from the menu list is described as follows:
Example: Fn button t [White balance] t Select the desired
setting
When you start an operation, an operation guide of control button functions
will be displayed at the bottom of the screen. Please refer to the guide when
operating the camera. The step-by-step description of the above example is
as follows:
1 Press the Fn button.
39
2 Select [White balance] with v/V/
b/B on the control button, then
press the center z to execute.
3 Following the operation guide,
select and execute the desired
function.
For example, to change , select with
v/V, adjust the value to +/– with b/B,
then press the center z to execute.
Operation guide
The operation guide list
The operation guide also indicates operations other than the control button
operation. The indications of icons are as follows.
MENU button
Returns with MENU button
Fn button
(Delete) button
(Zoom in) button
(Playback) button
Control dial
The functions selected by the Control button
Functions that will be used frequently in various shooting situations are
assigned to the control button. You can set up these shooting functions
directly and also switch the display status with the control button.
(Flash) (page 82)
(Drive mode) (page 97)
• Single-shot adv. (page 97)
40
• Continuous adv. (page 97)
• Self-timer (page 98)
• Self-timer(Cont.) (page 98)
• Bracket: Cont. (page 99)
• Remote Commander (page 101)
The functions selected by the Fn (Function) button
This button calls up the screens that are used for setting up or executing
functions used frequently in shooting or viewing.
Shooting mode
Viewing mode
Autofocus mode (78)
Metering mode (89)
White balance (91)
D-RangeOptimizer (94)
Creative Style (94)
Image Index (104)
Specify Printing (143)
Slide show (105)
Rotate (103)
The functions selected by the MENU button
You can set up the basic settings for the camera as a whole or execute
functions such as shooting, playback, or other operations.
Recording menu
Image size (116)
Aspect ratio (116)
Quality (117)
Flash compens. (88)
AF illuminator (84)
SteadyShot (45)
Color Space (96)
Long exp.NR (120)
High ISO NR (120)
1
2
Custom menu
Eye-Start AF (67)
Ctrl dial setup (121)
Red eye reduc. (84)
Auto review (124)
Auto off w/ VF (125)
1
41
Playback menu
Format (119)
Slide show (105)
Protect (109)
1
Specify Printing (143)
PlaybackDisplay (102)
Setup menu
LCD brightness (124)
Power Save (LV) (122)
Date/Time setup (123)
Power Save (OVF) (122)
CTRL FOR HDMI (114)
Display Color (122)
Help Guide disp. (122)
File number (118)
Select folder (119)
1
2
Audio signals (122)
Pixel mapping (156)
Cleaning mode (32)
3
Version (126)
Reset default (127)
42
Shooting an image without camera shake
“Camera shake” refers to unwanted movement of the camera that occurs
after the shutter button has been pressed, resulting in a blurred image.
To reduce camera shake, follow the instructions below.
Correct posture
Stabilize your upper body and take a position that keeps the
camera from moving.
In Live View mode
In viewfinder mode
Point 1
One hand holds the grip of the camera, and the other hand supports the lens.
Point 2
Take a secure stance with your feet shoulder-width apart.
44
Point 3
Lightly tuck your elbows against your body.
When shooting in a kneeling position, steady your upper body by placing
your elbow on your knee.
Camera shake warning indicator
Due to potential camera shake, the
(Camera shake warning) indicator
flashes. In this case, use a tripod or the
flash.
(Camera shake warning) indicator
Note
• The
(Camera shake warning) indicator is displayed only in the modes that
automatically set the shutter speed. This indicator is not displayed in M/S modes.
Using the SteadyShot function
This SteadyShot function can reduce the effect of camera shake by the
equivalent of approximately 2.5 to 3.5 increments of shutter speed.
The SteadyShot function is set to [On] in the default setting.
The SteadyShot scale indicator
The
(SteadyShot scale) indicator
shows the camera shake status. Wait until
the scale becomes low, then start
shooting.
(SteadyShot scale) indicator
To deactivate the SteadyShot function
MENU button t
1 t [SteadyShot] t [Off]
45
Note
• The SteadyShot function may not work optimally when the power has just been
turned on or when the shutter button has been pressed all the way down without
stopping halfway. Wait for the
(SteadyShot scale) indicator scale to go down,
and then press the shutter button down slowly.
Using a tripod
In the following cases, we recommend that you mount the camera on a
tripod.
• Shooting without a flash under dark conditions.
• Shooting with slow shutter speeds, which are typically used in night-time
shooting.
• Shooting a close subject, such as in macro shooting.
• Shooting with a telescopic lens.
Note
• When using a tripod, deactivate the SteadyShot function because there is a potential
for malfunction of the SteadyShot function (page 45).
46
/ Shooting with the automatic
setting
The “AUTO” mode allows you to easily shoot any subject under any
conditions because the camera makes appropriate judgments on the
situation to adjust the settings.
Select
when shooting in a location where the use of a flash is restricted.
When you turn the mode dial, the explanation of the selected mode and
methods of shooting are displayed on the screen (Help Guide disp.). You
can clear the Help Guide (page 122).
1 Set the mode dial to
(Flash Off).
or
or
2 Adjust the LCD monitor to an easily viewable angle and hold
the camera.
3 Place the desired subject within
the focus area.
• If the
(Camera shake warning)
indicator flashes, carefully shoot the
subject, holding the camera steady, or
by using a tripod.
(Camera shake
warning) indicator
Focus area
4 When using a zoom lens, turn the
zoom ring, then decide on your
shot.
Zoom ring
47
5 Press the shutter button halfway
down to focus.
When the focus is confirmed, z or
Focus indicator
6 Press the shutter button fully
down to shoot.
• Pressing the shutter button after the
(SteadyShot scale) indicator becomes
low makes the SteadyShot function
more effective.
(SteadyShot scale) indicator
Note
• Since the camera turns on the automatic setting function, many features will be
unavailable, such as exposure compensation, ISO setting. If you want to adjust
various settings, set the mode dial to P, then shoot your subject.
48
Shooting with a suitable setting for the
subject (Scene Selection)
Selecting an appropriate mode for the subject or the shooting conditions
allows you to shoot the image with a suitable setting for the subject.
When you turn the mode dial, the explanation of the selected mode and
methods of shooting are displayed on the screen (Help Guide disp.). You
can clear the Help Guide (page 122).
Note
• The camera makes appropriate judgments on the situation to adjust the settings.
Since the camera turns on the automatic setting function, many features will be
unavailable, such as exposure compensation, ISO setting.
49
Taking portrait photos
This mode is suitable for
zBlurring away backgrounds and
sharpening the subject.
zExpressing skin tones softly.
Set the mode dial to
(Portrait).
Shooting techniques
• To blur the background more, set the lens to the telephoto position.
• You can shoot a vivid image by focusing on the eye that is closer to the
lens.
• Use the lens hood (sold separately) to shoot backlit subjects.
• Use the red-eye reduction function if the eyes of your subject turn red
• Set the flash mode to (Flash Off) when you shoot without the flash
50
Taking landscape photos
This mode is suitable for
zShooting the entire range of scenery
in sharp focus with vivid colors.
Set the mode dial to
(Landscape).
Shooting techniques
• To accentuate the openness of the scenery, set the lens to wide angle.
• Set the flash mode to (Fill-flash) when you shoot with the flash
51
Taking small-subject photos
This mode is suitable for
zShooting close subjects such as
flowers, insects, dishes, or small
goods.
Set the mode dial to
(Macro).
Shooting techniques
• Get close to the subject and shoot at the minimum distance of the lens.
• You can shoot a closer subject using a macro lens (sold separately).
• Set the flash mode to (Flash Off) when you shoot a subject within 1 m
(3.3 feet).
• When shooting in macro mode, the SteadyShot function will not be fully
effective. Use a tripod to achieve better results.
• Set the flash mode to (Flash Off) when you shoot without the flash
52
Taking moving-subject photos
This mode is suitable for
zShooting moving subjects outdoors
or in bright places.
Set the mode dial to
(Sports Action).
Shooting techniques
• The camera shoots images continuously while the shutter button is
pressed.
• Press and hold the shutter button halfway down until the right moment.
• Set the flash mode to (Fill-flash) when you shoot with the flash
53
Taking sunset photos
This mode is suitable for
zShooting the red of the sunset
beautifully.
Set the mode dial to
(Sunset).
Shooting techniques
• Used to shoot an image accentuating the red color compared with other
modes. This is also suitable for shooting the beautiful red of the sunrise.
• Set the flash mode to (Fill-flash) when you shoot with the flash
54
Taking night view photos
This mode is suitable for
zShooting night scenes at a distance
without losing the dark atmosphere
of the surroundings.
Set the mode dial to
(Night Port./View).
Set the flash mode to (Flash Off) when you shoot a night view without
Shooting techniques
• Take care that the subject does not move to prevent the image from
blurring.
• The shutter speed is slower, so using a tripod is recommended.
Note
• The picture may not be taken properly when shooting a wholly dark night scene.
55
Shooting an image the way you want it
(Exposure mode)
With a single lens reflex camera, you can adjust the shutter speed (how
long the shutter is open) and aperture (the range that is in focus: depth of
field) to enjoy a variety of photographic expressions.
For example, you can use a fast shutter speed to shoot the ephemeral shape
of a wave, or you can accentuate a flower by opening the aperture to put
everything in front of and beyond the flower out of focus. These are a few
Adjusting the shutter speed and aperture not only creates the photographic
effects of movement and focus, but also determines the brightness of the
image by controlling the amount of exposure (the amount of light the
camera takes in), which is the most important factor in photo shooting.
Changing the brightness of the picture by the amount of exposure
Amount of
exposure
low
high
When using a faster shutter speed, the camera opens the shutter for a
shorter time. This means less time for the camera to take in light, resulting
in a darker picture. To take a brighter picture, you can open the aperture
(the hole through which the light passes) to some extent in order to adjust
the amount of light the camera takes in at one time.
The brightness of the picture adjusted by the shutter speed and aperture is
called “exposure.”
This section will show you how to adjust the exposure and enjoy various
photo expressions by the use of movement, focus, and light. You can find
out the right way to shoot the image and the subject you like.
56
When you turn the mode dial, the explanation of the selected mode and
methods of shooting are displayed on the screen (Help Guide disp.). You
can clear the Help Guide (page 122).
57
Shooting with program auto
This mode is suitable for
zUsing the automatic exposure, while
keeping the custom settings for ISO
sensitivity, Creative Style, D-Range
optimizer, etc.
1 Set the mode dial to P.
• Set the flash mode to (Fill-flash) when you shoot with the flash
3 Adjust the focus and shoot the subject.
58
Shooting by controlling the blur of the background
(Aperture priority)
This mode is suitable for
zPutting the subject in sharp focus
and blur everything in front of and
beyond the subject. Opening the
aperture narrows the range that is in
focus. (Depth of field becomes
shallower.)
zShooting the depth of the scenery.
Narrowing down the aperture widens
the range that is in focus. (Depth of
field becomes deeper.)
1 Set the mode dial to A.
59
2 Select the aperture value (F-
number) with the control dial.
• Smaller F-number: The foreground and
background of the subject are blurred.
Larger F-number: The subject and its
foreground and background are all in
focus.
• You cannot check the blurring of an
image on the LCD monitor or in the
viewfinder. Check the recorded image
and adjust the aperture.
Aperture (F-number)
3 Adjust the focus and shoot the
subject.
The shutter speed is automatically
adjusted to obtain correct exposure.
• When the camera judges that the proper
exposure is not obtained with the
selected aperture value, the shutter
speed flashes. In such cases, adjust the
aperture again.
Shutter speed
Shooting techniques
• The shutter speed may become slower depending on the aperture value.
When the shutter speed is slower, use a tripod.
• To blur the background more, use a telephoto lens or a lens that is
equipped with a smaller apperture value (bright lens).
• Set the flash mode to (Fill-flash) when you shoot with the flash
(page 82). However, the flash range differs according to the aperture
value. When you shoot with the flash, check the flash range (page 84).
60
Shooting a moving subject with various expressions
(Shutter speed priority)
This mode is suitable for
zShooting a moving subject at a
moment in time. Use a faster shutter
speed to crisply shoot an instant of
the movement.
zTracing the movement to express the
dynamism and flow. Use a slower
shutter speed to shoot a trailing
image of the moving subject.
1 Set the mode dial to S.
61
2 Select the shutter speed with the
control dial.
Shutter speed
3 Adjust the focus and shoot the
subject.
The aperture is automatically adjusted to
obtain correct exposure.
• When the camera judges that the proper
exposure is not obtained with the
selected shutter speed, the aperture
value flashes. In such cases, adjust the
shutter speed again.
Aperture (F-number)
Shooting techniques
• When the shutter speed is slower, use a tripod.
• When shooting an indoor sport, select a higher ISO sensitivity.
Notes
• The
(Camera shake warning) indicator is not indicated in shutter speed priority
mode.
• The higher the ISO sensitivity, the more conspicuous the noise.
• When the shutter speed is one second or more, noise reduction (Long exp.NR) will
be done after shooting. You cannot do any further shooting during the reduction.
However, when using the flash, if you close the aperture (a larger F-number) by
making the shutter speed slower, the light of the flash will not reach distant subjects.
62
Shooting with the exposure adjusted manually (Manual
exposure)
This mode is suitable for
zShooting with the desired exposure
setting by adjusting both the shutter
speed and aperture.
1 Set the mode dial to M.
2 Rotate the control dial to adjust
the shutter speed, and while
pressing the
button, rotate the
control dial to adjust the aperture.
• You can select the item the control dial
adjusts (shutter speed or aperture) with
[Ctrl dial setup] (page 121).
button
Aperture (F-number)
Shutter speed
63
3 Shoot the image after the
exposure is set.
• Check the exposure value on the EV
scale.
Toward +: Images become brighter.
Toward –: Images become darker.
The b B arrow appears if the set
exposure is beyond the range of the EV
scale. The arrow starts flashing if the
difference becomes greater.
Standard value
Notes
• The
(Camera shake warning) indicator is not indicated in manual exposure
mode.
• When the mode dial is set to M, the ISO setting [AUTO] is set to [100]. In M mode,
the ISO setting [AUTO] is not available. Set the ISO sensitivity as necessary
However, the flash range differs according to the aperture value. When you shoot
with the flash, check the flash range (page 84).
64
Shooting trails with long exposure (BULB)
This mode is suitable for
zShooting trails of light, such as
fireworks.
zShooting trails of stars.
1 Set the mode dial to M.
2 Rotate the control dial to the left
until [BULB] is indicated.
BULB
3 While pressing the
button,
rotate the control dial to adjust
the aperture (F-number).
button
65
4 Press the shutter button halfway down to adjust the focus.
5 Press and hold the shutter button for the duration of the
shooting.
As long as the shutter button is pressed, the shutter remains open.
Shooting techniques
• Use a tripod.
• Set the focus to infinity in manual focus mode when shooting fireworks,
etc.
Pressing the SHUTTER button on the Remote Commander triggers
BULB shooting and pressing it again stops BULB shooting. You do not
need to press and hold the SHUTTER button on the Remote Commander.
Notes
• When using a tripod, turn off the SteadyShot function (page 45).
• The longer the exposure time, the more conspicuous the noise on the image.
• After shooting, noise reduction (Long exp.NR) will be done for the same amount of
time that the shutter was open. You cannot do any further shooting during the
reduction.
66
Shooting with the viewfinder (OVF)
You can select either the LCD monitor (Live View) or the viewfinder
(OVF) to shoot images.
Switching to the viewfinder
Set the LIVE VIEW/OVF switch to
“OVF.”
The screen status changes as follows:
Viewfinder display
LCD monitor display
When you look into the viewfinder, the subject inside the focus area comes
into focus automatically (Eye-Start AF).
To deactivate the Eye-Start AF function
MENU button t
1 t [Eye-Start AF] t [Off]
• When attaching the FDA-M1AM Magnifier (sold separately) or the FDA-
A1AM Angle Finder (sold separately) to the camera, setting [Eye-Start
AF] to [Off] is recommended because the eyepiece sensors located below
the viewfinder may be activated.
67
Adjusting the focus of the finder (diopter adjustment)
Adjust the diopter-adjustment dial
to your eyesight until the indicators
appear clearly in the viewfinder.
• Turn the dial toward + when you are far-
sighted, toward – when you are near-sighted.
• Training the camera on a light allows you to
adjust the diopter easily.
When it is hard to rotate the diopter-adjustment dial
Put your fingers under the eyecup, and
slide it upward to remove the eyecup,
then adjust the diopter.
• When attaching the FDA-M1AM Magnifier
(sold separately) or the FDA-A1AM Angle
Finder (sold separately) to the camera,
remove the eyecup as illustrated and attach
them.
68
Switching the recording information display (DISP)
Press DISP on the control button to
switch between the Graphic Display and
the Standard Display.
When you rotate the camera to a vertical
position, the display automatically rotates
to adjust to the camera position.
Graphic Display
(Default setting)
Standard Display
No display
69
LCD monitor (Graphic Display)
The Graphic Display graphically shows the shutter speed and aperture
value and clearly illustrates how the exposure works. In AUTO or Scene
Selection mode, only the items that can be set are displayed. See the pages
in parentheses for details of operation.
A
C
Display
Indication
Display
Indication
reduction (84)
1/125
Shutter speed (61)
Aperture (59)
Drive mode (97)
F5.6
SteadyShot (45)
+2.0
Exposure compensation
B
Display
Indication
Shutter speed indicator*
Aperture indicator* (59)
* The pointer indicates the current
value.
70
LCD monitor (Standard Display)
See pages in parentheses for details of operation.
In AUTO or Scene Selection mode
In P/A/S/M mode
A
Display
Indication
Focus mode (78)
Display
Indication
AF area (79)
Metering mode (89)
Creative Style (94)
1/125
F5.6
+2.0
Shutter speed (61)
Aperture (59)
Exposure (86)
SteadyShot (45)
AWB
White balance (Auto,
Preset, Custom, Color
temperature, Color filter)
B
Display
Indication
reduction (84)
D-Range Optimizer (94)
Exposure compensation
Flash compensation (88)
Drive mode (97)
72
Viewfinder
* When using the HVL-F58AM/HVL-
F42AM Flash (sold separately), you
can shoot with the High-speed sync
feature at any shutter speed. For
details, refer to the operating
A
Display
Indication
AF area (79)
Shooting area for aspect
ratio 16:9 (116)
instructions supplied with the flash.
B
Display
Indication
Flash compensation (88)
Flash charging (82)
Wireless flash (85)
High-speed sync*
Manual focus (80)
Focus
WL
z
125
5.6
Shutter speed (61)
Aperture (59)
0
“Shooting unavailable”
warning (97)
Camera shake warning
SteadyShot scale (45)
Aspect ratio 16:9 (116)
74
Using the shooting function
Selecting the focus method
There are two methods for adjusting the focus: autofocus and manual focus.
Depending on the lens, the method for switching between the auto focus
and manual focus is different.
The switch to be To switch to auto
used focus
To switch to manual
focus
The type of lens
The lens is
equipped with a
focus mode switch switch on the
camera to AF.)
Lens (Always set Set the focus mode Set the focus mode
the focus mode switch on the lens to switch on the lens to
AF. MF.
The lens is not
equipped with a
focus mode switch
Camera
Set the focus mode Set the focus mode
switch on the camera switch on the camera
to AF.
to MF.
Using autofocus
1 Set the focus mode switch on the
camera to AF.
2 When the lens is equipped with
the focus mode switch, set it to
AF.
75
Focus area sensor
3 Press the shutter button halfway
down to check the focus and shoot
the image.
• When the focus is confirmed, the focus
indicator changes to z or
(below).
• The green frames are indicated at an
area where the focus has been
confirmed.
Focus area
Focus indicator
Shooting technique
• To select the area used for focusing, set up [AF area] (page 79).
Focus indicator
Focus indicator
Status
z lit
Focus locked. Ready to shoot.
lit
Focus is confirmed. Focal point moves following a moving
subject. Ready to shoot.
lit
Still focusing. You cannot release the shutter.
Cannot focus. The shutter is locked.
z flashing
Subjects that may require special focusing
Using the autofocus, it is hard to focus on the following subjects. In such
• A subject that is low in contrast, such as blue sky or a white wall.
• Two subjects at different distances overlapping in the AF area.
• A subject that is composed of repeating patterns, such as the facade of a
building.
• A subject that is very bright or glittering, such as the sun, the body of an
automobile, or the surface of water.
• Ambient light is not sufficient.
76
To measure the exact distance to the subject
The mark located on the top of the
camera shows the location of the image
sensor*. When you measure the exact
distance between the camera and the
subject, refer to the position of the
horizontal line.
* The image sensor is the part of the
camera that acts as the film.
Notes
• If the subject is closer than the minimum shooting distance of the attached lens, the
focus cannot be confirmed. Make sure you put enough distance between the subject
and the camera.
• When the focus mode switch on the camera is set to MF, the correct focus is not
achieved, even if the focus mode switch on the lens is set to AF. To switch to auto
focus, set the focus mode switch on the camera to AF.
Shooting with your desired composition (Focus-lock)
1 Place the subject within the AF
area and press the shutter button
halfway down.
The focus and exposure are fixed.
2 Keep the shutter button halfway
down, and put the subject back in
the original position to re-
compose the shot.
3 Press the shutter button fully down to take the picture.
77
Selecting the focus method to suit the movement of the
subject (Autofocus mode)
Fn button t [Autofocus mode] t Select the desired setting
(Single-shot
The camera focuses and the focus is locked when you press
the shutter button halfway down.
AF)
(Automatic AF) The [Autofocus mode] is switched between Single-shot AF
and Continuous AF according to the movement of the
subject.
When you press and hold the shutter button halfway down, if
the subject is motionless, the focus is locked and if the
subject is in motion, the camera continues to focus.
(Continuous
The camera continues to focus while the shutter button is
pressed and held halfway down.
AF)
• The audio signals will not sound when the subject is in
focus.
Shooting techniques
• Use
• Use
(Single-shot AF) when the subject is motionless.
(Continuous AF) when the subject is in motion.
Note
•
(Automatic AF) is selected when the exposure mode is set to AUTO or one of
the following Scene Selection modes:
(Night Port./View).
(Single-shot AF) is selected when the exposure mode is set to
Scene Selection.
(Continuous AF) is selected when the exposure mode is set to
Action) in Scene Selection.
(Portrait),
(Landscape),
(Sunset), or
(Macro) in
(Sports
78
Selecting the focus area (AF area)
Select the desired AF area to suit the
shooting conditions or your preference.
The green frames are indicated at an area
where the focus has been confirmed.
• The area used for focusing is
illuminated briefly in viewfinder mode.
AF area
Area
Fn button t [AF area] t Select the desired setting
(Wide)
The camera determines which of the nine AF areas is used in
focusing within the AF area. If you press and hold the center
of the control button, you can adjust the focus using the AF
areas located in the center area.
(Spot)
(Local)
The camera uses the AF area located in the center area
exclusively.
Choose the area for which you want to activate the focus
from among nine areas with the control button. If you press
and hold the center of the control button during the shooting,
you can temporarily adjust the focus using the AF areas
located in the center area.
Notes
• When the exposure mode is set to AUTO or Scene Selection, [AF area] is fixed to
(Wide) and you cannot select the other settings.
• The AF area may not be illuminated during continuous shooting or when the shutter
button is pressed all the way down without pause.
• The green frames that are displayed when the focus has been confirmed indicate the
area used for focusing. They do not indicate the size of the area. The AF area and the
frames may not be located on the same position. This is not a malfunction.
79
Adjusting the focus manually (Manual focus)
When it is difficult to get the proper focus in autofocus mode, you can
adjust the focus manually.
1 Set the focus mode switch on the
lens to MF.
2 When the lens is not equipped
with the focus mode switch, set
the focus mode switch on the
camera to MF.
3 Rotate the focusing ring of the
lens to achieve a sharp focus.
Focusing
ring
Notes
• In the case of a subject that can be focused in autofocus mode, the z indicator lights
up when the focus is confirmed. When the Wide AF area is used, the center area is
used, and when the Local AF area is used, the area that is selected with the control
button is used.
• When using a tele converter (sold separately), etc., rotation of the focusing ring may
not be smooth.
• The correct focus in the viewfinder is not achieved if the diopter is not adjusted
properly in viewfinder mode (page 68).
• The direct manual focus function is not available on this camera.
80
Zooming in in one step
You can zoom in to the center of an image using the smart teleconverter
(Digital zoom) and record the image.
1 Set the LIVE VIEW/OVF switch to
“LIVE VIEW.”
button
2 Press the
button.
• Each time you press the
button, the
zoom scaling changes as follows:
Approx. ×1.4 t Approx. ×2 t Off
The image size is automatically set to the following regardless of the
selected image size.
Zoom scaling
Approx. ×1.4
Approx. ×2
Image size
M*
S*
* The number of pixels in the image size selected here is different from that
of the image size selected in normal mode.
M: 3264 × 2176 pixels
S: 2416 × 1600 pixels
Notes
• When the LIVE VIEW/OVF switch is set to “OVF,” the smart teleconverter is
unavailable.
• When [Quality] is set to
teleconverter is unavailable.
(RAW) or
(RAW & JPEG), the smart
• When the smart teleconverter is available (when in autofocus mode), [AF area] is set
to (Spot).
• When the smart teleconverter is available, [Metering mode] is set to
segment).
(Multi
81
Using the flash
In a dark location, using the flash allows you to shoot the subject brightly,
and it also helps to prevent camera shake. When shooting into the sun, you
can use the flash to shoot a bright image of the backlit subject.
When the mode dial is set to AUTO, the flash pops up automatically if it is
dark or you are shooting into the light.
1
on the control button t Select
the desired setting
2 After the flash has finished
charging, shoot the subject.
Flashing: The flash is being charged.
When the indicator flashes, you cannot
release the shutter.
Lit: The flash has been charged and is
ready to fire.
(Flash charging)
indicator
• When you press the shutter button
halfway down under dark lighting in
autofocus mode, the flash may be fired
to help focus on a subject (AF
illuminator).
82
(Flash Off)
(Autoflash)
(Fill-flash)
(Slow sync.)
Does not fire even if it is dark.
Fires if it is dark or against light.
Fires every time you trigger the shutter.
Fires every time you trigger the shutter. Slow sync shooting
allows you to shoot a clear image of both the subject and the
background by slowing the shutter speed.
(Rear sync.)
(Wireless)
Fires right before the exposure is completed everytime you
trigger the shutter.
Fires an external flash (sold separately) that is off the camera
and away from it (Wireless flash shooting).
Shooting techniques
• The lens hood (sold separately) may block the light of the flash. Remove
the lens hood when using the flash.
• When using the flash, shoot the subject at a distance of 1 m (3.3 feet) or
greater.
• When shooting indoors or shooting nightscapes, you can use slow sync to
shoot a brighter image of people and backgrounds.
• You can use rear sync to shoot a natural image of the trail of a moving
subject such as a moving bicycle or a walking person.
Notes
• Do not hold the camera by grabbing the flash emitter.
• Shooting conditions required to prevent shadows from appearing on an image vary,
depending on the lens.
• When the exposure mode is set to AUTO or Scene Selection, the
(Rear sync.), and (Wireless) items cannot be selected.
(Slow sync.),
83
The flash range
The range of the built-in flash depends on the ISO sensitivity and aperture
value. Refer to the following table.
Aperture
F2.8
AUTO 1.4 – 7.1 m (4.6 – 23 1 – 5 m (3.3 – 16
feet) feet)
F4.0
F5.6
ISO
setting
1 – 3.6 m (3.3 – 11
feet)
100
200
400
800
1 – 3.6 m (3.3 – 11 1 – 2.5 m (3.3 – 8.2 1 – 1.8 m (3.3 – 5.9
feet) feet) feet)
1 – 5.1 m (3.3 – 16 1 – 3.5 m (3.3 – 11 1 – 2.5 m (3.3 – 8.2
feet)
feet)
feet)
1.4 – 7.1 m (4.6 – 23 1 – 5 m (3.3 – 16
1 – 3.6 m (3.3 – 11
feet)
feet)
feet)
2 – 10 m (6.6 – 32
feet)
1.4 – 7.1 m (4.6 – 23 1 – 5.1 m (3.3 – 16
feet) feet)
The AF illuminator
• AF illuminator does not operate when [Autofocus mode] is set to
(Continuous AF) or the subject is moving in (Automatic AF). (The
or indicator lights.)
• The AF illuminator may not operate with focal lengths of 300 mm or longer.
• When an external flash is attached, the AF illuminator of the external
flash is used.
To deactivate the AF illuminator
MENU button t
1 t [AF illuminator] t [Off]
To use the red-eye reduction
The red-eye reduction reduces the red-eye phenomenon by providing pre-
flash (low-flash light) a few times before shooting when using the flash.
MENU button t
1 t [Red eye reduc.] t [On]
84
Performing wireless flash shooting
With an external wireless flash (sold separately), you can shoot with the
flash without a cord when the external flash is not attached to the camera.
By changing the position of the flash, you can shoot an image with a three
dimensional feel by highlighting the contrast of light and shadow on the
subject.
For the actual steps of shooting, refer to the operating instructions of the
flash.
1 Attach the wireless flash to the Auto-lock Accessory Shoe and
turn both the camera and the flash on.
2
on the control button t
(Wireless)
3 Remove the wireless flash from the Auto-lock Accessory Shoe.
Notes
• The camera cannot perform a pre-flash test of the wireless flash. Confirm that the
flash fires properly by releasing the shutter.
• The camera cannot carry out the wireless lighting ratio control.
• Turn off the wireless flash mode after wireless flash shooting. If the built-in flash is
used while the wireless flash mode is still active, inaccurate flash exposures will
result.
• Change the channel of the external flash when another photographer is using a
wireless flash nearby and his/her built-in flash light causes your external flash to fire.
To change the channel of the external flash, refer to the operating instructions
supplied with it.
85
Adjusting the brightness of the image
(Exposure, Flash compensation,
Metering)
Using brightness compensation for the entire image
(Exposure compensation)
Except for recording mode M, the exposure is automatically selected
(Automatic exposure).
Based on the exposure acquired by the automatic exposure, you can
perform exposure compensation by shifting the exposure to either the +
side or the – side, depending on your preference. You can make the entire
image brighter by shifting to the + side. The entire image becomes darker
when you shift it to the – side.
Adjust in the –
direction
Base exposure
Adjust in the +
direction
button
1 Press the
button.
• The exposure compensation screen is
displayed in the viewfinder mode.
2 Adjust the exposure with the
control dial.
Toward + (over): Brightens an image.
Toward – (under): Darkens an image.
Standard exposure
86
3 Adjust the focus and shoot the subject.
Shooting techniques
• Adjust the compensation level by checking the recorded image.
• Using bracket shooting, you can shoot multiple images with the exposure
Note
• This item cannot be set when the exposure mode is set to AUTO, M (Manual
exposure) or Scene Selection.
To shoot while checking the screen using the histogram
The histogram displays the luminance
distribution that shows how many pixels
of a particular brightness exist in the
picture. To display the histogram, press
102).
Dark
Light
87
The exposure compensation will change
the histogram accordingly. The right
illustration is an example.
Shooting with the exposure
compensation on the positive side
brightens the whole picture, making the
entire histogram shift to the bright side
(right side). If the exposure compensation
is applied on the negative side, the
histogram will shift to the other side.
Both ends of the histogram show a high-
key or low-key portion. It is impossible to
restore these area with a computer later.
Adjust the exposure if necessary and
shoot again.
Notes
• The histogram displayed in Live View mode does not indicate the final recorded
image. It indicates the condition of the image just monitored on the LCD monitor.
The histogram will differ based on aperture setting, etc.
• The histogram differs between shooting and playback in the following situations:
– When firing the flash.
– When the subject has low intensity, such as night scenery.
Adjusting the amount of flash light (Flash compensation)
When shooting with the flash, you can adjust the amount of flash light
alone, without changing the exposure compensation. You can only change
the exposure of a main subject which is within the flash range.
MENU button t
1 t [Flash compens.] t Select the
desired setting
Toward +: Makes the flash level higher.
Toward –: Makes the flash level lower.
88
Notes
• This item cannot be set when the exposure mode is set to AUTO or Scene Selection.
• If you have adjusted the flash level,
appears on the LCD monitor/in the
viewfinder when the built-in flash is pulled up. When you adjust it, be careful not to
forget to reset the value.
• The higher flash effect may not be visible due to the limited amount of flash light, if
the subject is outside the maximum range of the flash. If the subject is very close, the
lower flash effect may not be visible.
Exposure compensation and flash compensation
Exposure compensation changes the shutter speed, aperture, and ISO sensitivity (when
[AUTO] is selected) to perform the compensation. If the flash is used, the amount of
flash light is also changed.
However, flash compensation only changes the amount of flash light.
Selecting the method for measuring the brightness of a
subject (Metering mode)
Fn button t [Metering mode] t Select the desired mode
(Multi segment) This mode measures light on each area after dividing the total
area into multiple areas and determines the proper exposure
of the entire screen.
(Center weighted) While emphasizing the central area of the screen, this mode
measures the average brightness of the entire screen.
(Spot)
This mode measures light at or around the focus area located
in the center of the frame.
Shooting technique
• Use (Multi segment) metering for general shooting.
Note
• When the exposure mode is set to AUTO or Scene Selection, [Metering mode] is
fixed to
(Multi segment) and you cannot select other modes.
89
Setting ISO
Sensitivity to light is expressed by the ISO number (recommended
exposure index). The larger the number, the higher the sensitivity.
1 Press ISO on the control button to
display the ISO screen.
2 Select the desired value with v/V on the control button.
• The larger the number, the higher the noise level.
Notes
• When the exposure mode is set to AUTO or Scene Selection, ISO is fixed to AUTO
and you cannot select other ISO numbers.
• When the exposure mode is set to P/A/S and ISO is set to [AUTO], ISO is
automatically set between ISO 100 and ISO 400.
• The [AUTO] setting is not provided in recording mode M. If you change the
recording mode to M with the [AUTO] setting, it is switched to [100]. Set the ISO
according to your shooting conditions.
90
Adjusting the color tones (White balance)
The color tone of the subject changes depending on the characteristics of
the light source. The table below shows how the color tone changes based
on various light sources, compared with a subject that appears white under
the sunlight.
Daylight
Cloudy
Fluorescent
Incandescent
Weather/
lighting
Characteristics
of light
White
Bluish
Green-tinged
Reddish
White balance is a feature that adjusts the color tone to approximate what
you see. Use this feature when the color tone of the image did not come out
as you expected, or when you want to change the color tone on purpose for
photographic expression.
Notes
• When the exposure mode is set to AUTO or Scene Selection, [White balance] is
fixed to AWB (Auto WB) and you cannot select other modes.
• If the only light source available is a mercury lamp or a sodium lamp, the camera
will not be able to acquire the accurate white balance because of the characteristics
of the light source. Use the flash in such cases.
Adjusting the white balance to suit a specific light source
(Auto/Preset white balance)
Fn button t [White balance] t Select the desired setting
• When [AWB] is not selected, you can fine tune the color tone with b/B
on the control button. Adjusting it toward + turns the image reddish and
adjusting it toward – turns the image bluish.
91
AWB (Auto WB)
The camera automatically detects a light source and adjusts
the color tones.
(Daylight)
(Shade)
If you select an option to suit a specific light source, the color
tones are adjusted for the light source (preset white balance).
(Cloudy)
(Tungsten)
(Fluorescent)
(Flash)
Shooting technique
• When you select
(Custom), you can register your setting (below).
Registering the color tones (Custom white balance)
In a scene where the ambient light consists of multiple types of light source,
use of custom white balance is recommended in order to accurately
reproduce the whiteness.
1 Fn button t [White balance] t
2 Select [
SET] with b/B on the control button, then press the
center of the control button.
3 Hold the camera so that the white area fully covers the focus
area located in the center, and then press the shutter button
down.
The shutter clicks and the calibrated values (ColorTemperature and Color
filter) are displayed.
92
4 Press the center of the control button.
The monitor returns to the recording information display with the memorized
custom white balance setting retained.
• The custom white balance setting registered in this operation is effective
until a new setting is registered.
Note
• The message “Custom WB error” indicates that the value is beyond the expected
range. (When the flash is used on a subject in close proximity or a subject with a
bright color is in the frame.) If you register this value, the
indicator turns yellow
on the recording information display on the LCD monitor. You can shoot at this
point, but it is recommended that you set the white balance again to get a more
correct white balance value.
To call the custom white balance setting
Fn button t [White balance] t
(Custom)
Note
• If the flash is used when the shutter button is pressed, a custom white balance is
registered with the flash light taken into account. Take pictures with the flash in later
shootings.
93
Image processing
Correcting the brightness of the image (D-Range
Optimizer)
Fn button t [D-RangeOptimizer] t Select the desired setting
(Off)
No optimization.
(Standard)
When there is a sharp contrast of light and shadow between
the subject and the background, which is common when
shooting into the sun, the camera attenuates the contrast
across the entire image to produce an image with proper
brightness and contrast.
(Advanced)
By dividing the image into small areas, the camera analyses
the contrast of light and shadow between the subject and the
background, producing the image with the optimal brightness
and gradation.
Notes
•
(Advanced) is selected when the exposure mode is set to AUTO or one of the
following Scene Selection modes:
(Standard) is selected when the exposure mode is set to
Scene Selection.
(Portrait),
(Landscape) or
(Macro).
(Sports Action) in
(Off) is selected when the exposure mode is set to
Port./View) in Scene Selection.
(Sunset) or
(Night
• For enlarged RAW images, the effects of the D-Range optimizer other than
(Standard) cannot be checked on the camera.
• When shooting with the D-Range optimizer, the image may be noisy.
Selecting your desired image processing (Creative Style)
1 Fn button t [Creative Style] t Select the desired setting
2 When you want to adjust (Contrast), (Saturation), or
(Sharpness), select the desired item with b/B, then adjust the
value with v/V.
94
(Standard)
(Vivid)
For shooting various scenes with rich gradation and beautiful
colors.
The saturation and contrast are heightened for shooting
striking images of colorful scenes and subjects such as
flowers, spring greenery, blue sky, or ocean views.
(Portrait)
For shooting the skin color in a soft tone, ideally suited to
shooting portraits.
(Landscape) The saturation, contrast, and sharpness are heightened for
shooting vivid and crisp scenery. Distant landscapes also
stand out more.
(Night view) The contrast is attenuated for shooting a nightscape that is
more faithful to the real view.
(Sunset)
(B/W)
For shooting the beautiful red of the setting sun.
For shooting images in black and white monotone.
(Contrast), (Saturation), and
Creative Style item.
(Sharpness) can be adjusted for each
(Contrast)
The higher the value selected, the more the difference of light
and shadow is accentuated, thus making an impact on an
image.
(Saturation)
(Sharpness)
The higher the value selected, the more vivid the color. When
a lower value is selected, the color of the image is restrained
and subdued.
Adjusts the sharpness. The higher the value selected, the
more the contours are accentuated, and the lower the value
selected, the more the contours are softened.
Notes
• When the exposure mode is set to AUTO or Scene Selection, [Creative Style] is
fixed to
• When
(Standard) and you cannot select other settings.
(B/W) is selected, you cannot adjust the saturation.
95
Changing the range of color reproduction (Color Space)
The way colors are represented with combinations of numbers or the range
of color reproduction is called “color space.” You can change the color
space, depending on your purpose.
MENU button t
2 t [Color Space] t Select the desired
setting
sRGB
This is the standard color space of the digital camera. Use
sRGB in normal shooting, such as when you intend to print
out the images without any modification.
Adobe RGB
This has a wide range of color reproduction. When a large
part of the subject is vivid green or red, Adobe RGB is
effective.
• The file name of the image starts with “_DSC.”
Notes
• Adobe RGB is for applications or printers that support color management and
DCF2.0 option color space. Using some applications or printers that do not support
them may result in or print images that do not faithfully reproduce the color.
• When displaying images that were recorded with Adobe RGB on the camera or non-
Adobe RGB-compliant devices, the images are displayed with low saturation.
96
Selecting the drive mode
This camera has five drive modes, such as single-shot advanced, and
continuous advanced. Use them to suit your purpose.
Shooting single shot
This mode is for normal shooting.
on the control button t
(Single-shot adv.)
Note
• When the exposure mode is set to
shoot single shot.
(Sports Action) in Scene Selection, you cannot
Shooting continuously
The camera records the images continuously at the following speeds*.
Maximum 2 images per
second
Live View mode
Maximum 2.5 images per
second
Viewfinder mode
* Our measurement conditions. The speed of continuous shooting is slower,
depending on shooting conditions.
1
on the control button t
(Continuous adv.)
97
2 Adjust the focus and shoot the subject.
• When you press and hold the shutter button, the recording continues.
The maximum number of continuous shots
The number of continuous shooting images obtainable has an upper limit.
Fine/Standard
RAW & JPEG
RAW
No limit (Until the memory card is full)
3 images
6 images
Notes
• You cannot shoot images continuously when “0” flashes in the viewfinder. Wait
until the indicator disappears.
• When the exposure mode is set to a Scene Selection mode other than
Action), you cannot shoot continuously.
(Sports
• The speed of continuous shooting may be slower when the battery level is
insufficient or at low ambient temperatures.
Using the self-timer
The 10-second self-timer is convenient when the photographer appears in a
photo and the 2-second self-timer is convenient to reduce the camera shake.
[Self-timer(Cont.)] is convenient to prevent failure because the camera
continuously shoots either three or five images after a 10 second pause.
1
on the control button t
(Self-timer) t Select the
desired setting
• The number after
is the number of
seconds that is currently selected.
• Select
timer.
to use the continuous self-
98
2 Adjust the focus and shoot the subject.
• When the self-timer is activated, audio signals and the self-timer lamp
indicate the condition. The self-timer lamp flashes quickly and the audio
signal sounds quickly right before the shooting.
To cancel the self-timer
Press
on the control button.
Note
• When you shoot images using the viewfinder, use the eyepiece cover (page 28).
Shooting images with the exposure shifted (Exposure
bracket)
Base exposure
– direction
+ direction
Bracket shooting allows you to shoot several images, each with different
degrees of exposure. This camera is equipped with an auto bracket
function. Specify the value of deviation (steps) from the base exposure, and
the camera shoots while automatically shifting the exposure. You can
choose an image that has the brightness you like after shooting is finished.
When the flash is fired, flash bracket shooting is used to shift the amount of
flash light. To shoot, press the shutter button shot by shot.
1
on the control button t
(Bracket: Cont.) t Select
the desired bracket step
2 Adjust the focus and shoot the subject.
The base exposure is set at the first shot in the bracket.
99
* (Bracket:
Shoots three images with the exposure shifted by a selected
step.
Cont.)
Press and hold the shutter button until the recording stops.
When the flash is fired, press the shutter button shot by shot.
* _ EV displayed with
is the step currently selected.
Notes
• When the mode dial is set to M, the exposure is shifted by adjusting the shutter
speed.
• When you adjust the exposure, the exposure is shifted based on the compensated
value.
• The bracket cannot be used when the recording mode is set to AUTO or Scene
Selection.
The EV scale in bracket shooting
Ambient light* bracket
0.3 steps, three shots
Exposure compensation 0
Flash bracket
0.7 steps, three shots
Flash compensation –1.0
LCD monitor (Live View
mode)
LCD monitor
(Viewfinder mode/
Standard Display)
Shown in the top row.
Shown in the bottom row.
Viewfinder
* Ambient light: Any light other than the flash light that shines on the scene
for an extended period of time, such as natural light, a light bulb, or a
fluorescent light.
• In bracket shooting, the same number of indices as the number of
recordable images is displayed on the EV scale. However, in flash bracket
shooting, the indices are not displayed in the viewfinder.
• When the bracket shooting starts, the indices that indicate already
recorded images start to disappear one by one.
100
• In viewfinder mode, if the shutter button is pressed halfway down and
released, “br 1” appears. “Fbr 1” appears for the flash bracket. When
flash bracket shooting starts, it indicates what number the next frame is,
for instance, “Fbr 2,” “Fbr 3.”
Shooting with the Remote Commander
You can shoot using the SHUTTER and 2SEC (the shutter is released after
2 seconds) buttons on the RMT-DSLR1 Wireless Remote Commander
(sold separately). Also, refer to the operating instructions supplied with the
Wireless Remote Commander.
1
on the control button t
(Remote Commander)
2 Focus on the subject, point the transmitter of the Remote
Commander to the remote sensor, and shoot the image.
Note
• When you shoot images using the viewfinder, use the eyepiece cover (page 28).
101
Using the viewing function
Playing back images
The last recorded image is displayed on the LCD monitor.
1 Press the
button.
button
2 Select an image with b/B on the control button.
To return to the shooting mode
Press the
button again.
To switch the recording data display
Press DISP on the control button.
Each time you press DISP on the control button, the screen changes as
follows.
Histogram display
With recording
data
Without recording
data
To select the orientation when playing back an image recorded in the
portrait position
MENU button t
1 t [PlaybackDisplay] t Select the
desired setting
Note
• When you play back the image on a TV or a computer, the image will be displayed
in the portrait position even if [Manual rotate] is selected.
102
Rotating an image
1 Fn button t [Rotate]
2 Press the center of the control button.
The image is rotated counter-clockwise. When you want to do another
rotation, repeat step 2.
• Once you rotate the image, the image is played back in the rotated position,
even if you turn off the power.
To return to the normal playback screen
Press the
button.
Note
• When you copy rotated images to a computer, “PMB” contained on the CD-ROM
(supplied) can display the rotated images correctly. However, the images may not be
rotated depending on the software.
Enlarging images
An image can be enlarged for closer examination. This is convenient to
check the focus condition of a recorded image.
button
1 Display the image you want to
enlarge, then press the button.
2 Zoom the image in or out with the
control dial.
103
3 Select the portion you want to enlarge with v/V/b/B on the
control button.
To cancel the enlarged playback
Press the
button so that the image returns to the normal size.
Scaling range
The scaling range is as follows.
Image size
Scaling range
L
Approx. ×1.1 – ×14
Approx. ×1.1 – ×11
Approx. ×1.1 – ×7.2
M
S
Switching to the display of the image list
Fn button t [Image Index] t Select the desired number of
images to be displayed
The screen changes to the image index screen.
To return to the single-image screen
Press the center of the control button when you select the desired image.
To select a folder
1Select the folder bar with b/B on the
control button, then press the center.
2Select the desired folder with v/V,
then press the center.
Folder bar
104
Playing back images automatically (Slide show)
The slide show can be operated either using the Fn button or the MENU
button. Here operation using the Fn button is described.
Fn button t [Slide show]t [OK]
Plays back recorded images in order (Slide show). The slide show
automatically stops after all the images have been played back.
• You can view the previous/next image with b/B on the control button.
To pause the slide show
Press the center of the control button. Pressing again starts the slide show
again.
To end in the middle of the slide show
Press the
button.
To choose the interval between the images in slide show
Fn button t [Slide show] t [Interval] t Select the desired
number of seconds
To play back repeatedly
Fn button t [Slide show] t [Repeat] t [On]
105
Checking the information of recorded
images
Each time you press DISP on the control button, the information display
Basic information display
Display
Indication
Display
Indication
NO CARD “No card” warning
Memory card (22)
100-0003 Folder - file number
-
Protect (109)
DPOF3
Image quality (117)
ratio (116)
Remaining battery
warning (18)
1/125
F3.5
Shutter speed (61)
Aperture (59)
ISO100
ISO sensitivity (90)
2010 1 1 Date of recording
10:37AM
3/7
File number/total number
of images
106
Histogram display
A
Display
–0.3
Indication
Flash compensation (88)
Metering mode (89)
Focal length (150)
Creative Style (94)
Display
Indication
Memory card (22)
35mm
100-0003 Folder - file number
-
Protect (109)
DPOF3
DPOF set (143)
Image quality (117)
AWB +1 White balance (Auto,
5500K M1 Preset, Color
temperature, Color filter)
ratio (116)
D-Range Optimizer (94)
Remaining battery
warning (18)
2010 1 1 Date of recording
10:37AM
3/7
File number/total number
of images
B
Display
Indication
Histogram (87)
1/125
Shutter speed (61)
Aperture (59)
F3.5
ISO100
ISO sensitivity (90)
–0.3
Exposure compensation
107
Protecting images (Protect)
You can protect images against accidental erasure.
The protect function can be operated either using the Fn button or the
MENU button. Here operation using the Fn button is described.
Protecting selected images/canceling the protection of the
selected images
1 Fn button t [Protect] t [Marked images]
2 Select the image you want to
-
protect with b/B on the control
button, then press the center of
the control button.
A - mark appears on the selected
image.
• To cancel a selection, press the center
again.
3 To protect other images, repeat step 2.
4 Press the Fn button.
5 Select [OK] with v on the control button, then press the center
of the control button.
Protecting all the images/canceling the protection of all the
images
Fn button t [Protect] t [All images] or [Cancel all] t [OK]
109
Deleting images (Delete)
Once you have deleted an image, you cannot restore it. Check whether to
delete the image or not beforehand.
The delete function can be operated either from the Fn button or from the
MENU button. Here operation using the Fn button is described.
Note
• Protected images cannot be deleted.
Deleting the image that is currently displayed
1 Display the image you want to
delete and press the
button.
button
2 Select [Delete] with v, then press the center of the control
button.
Deleting the selected images
1 Fn button t [Delete] t [Marked images]
2 Select the images you want to
delete with the control button,
then press the center of the
control button.
A
mark appears on the selected
image.
Total number
3 To delete other images, repeat step 2.
110
4 Press the Fn button.
5 Select [Delete] with v on the control button, then press the
center of the control button.
Deleting all the images in the folder
1 Fn button t [Image Index] t Select the desired number of
images
2 Select the folder bar with b on
the control button.
Folder bar
3 Press the center of the control button, then select the folder you
want to delete with v/V.
4 Press the button.
5 Select [Delete] with v, then press the center of the control
button.
Deleting all the images all at once
Fn button t [Delete] t [All images] t [Delete]
Note
• It may take a long time to delete a lot of images by selecting [All images]. It is
recommended that you delete images on a computer or format the memory card
using the camera.
111
Viewing images on a TV screen
To view images recorded on the camera on a TV set, an HDMI cable (sold
separately) and an HD TV equipped with an HDMI connector are required.
1 Turn off both your camera and the 1 To the HDMI
connector
TV, and connect the camera to the
TV.
HDMI cable
(sold separately)
2 To the
HDMI terminal
2 Turn on the TV and switch the input.
• See also the operating instructions supplied with the TV.
3 Turn on the camera.
Images shot with the camera appear on
the TV screen.
Select the desired image with b/B on the
control button.
• The LCD monitor on the camera does
not turned on.
Control button
Notes
• Use an HDMI cable with the HDMI logo.
• Use an HDMI mini connector on one end (for the camera), and a connector suitable
for connection to your TV on the other end.
112
• By connecting your camera to Sony’s VIDEO-A compatible TV using an HDMI
cable, the TV automatically selects the appropriate image quality for viewing still
pictures. Please refer to the operating instructions of Sony’s VIDEO-A compatible
TV for more details.
• Some devices may not work properly.
• Do not connect the output connector of the device with the HDMI terminal on the
camera. This may cause a malfunction.
On “PhotoTV HD”
This camera is compatible with the “PhotoTV HD” standard.
By connecting Sony’s PhotoTV HD-compatible devices using an HDMI
cable, a whole new world of photos can be enjoyed in breathtaking Full HD
quality.
“PhotoTV HD” allows for a highly-detailed, photo-like expression of
subtle textures and colors.
To use your camera abroad
The camera automatically detects the color system to match that of the
connected video device.
On TV color systems
If you want to view images on a TV screen, you need a TV with a video
input jack and the video cable. The color system of the TV must match that
of your digital still camera. Check the following lists for the TV color
system of the country or region where the camera is used.
NTSC system
Bahama Islands, Bolivia, Canada, Central America, Chile, Colombia, Ecuador,
Jamaica, Japan, Korea, Mexico, Peru, Surinam, Taiwan, the Philippines, the U.S.A.,
Venezuela, etc.
PAL system
Australia, Austria, Belgium, China, Czech Republic, Denmark, Finland, Germany,
Holland, Hong Kong, Hungary, Italy, Kuwait, Malaysia, New Zealand, Norway,
Poland, Portugal, Singapore, Slovak Republic, Spain, Sweden, Switzerland, Thailand,
United Kingdom, etc.
PAL-M system
Brazil
113
PAL-N system
Argentina, Paraguay, Uruguay
SECAM system
Bulgaria, France, Guiana, Iran, Iraq, Monaco, Russia, Ukraine, etc.
Using “BRAVIA” Sync
By connecting the camera to a TV that supports “BRAVIA” Sync using an
HDMI cable, you can operate the camera with the TV Remote Control.
1 Connect a TV that supports “BRAVIA” Sync to the camera
The input is automatically switched and the image shot with the camera
appears on the TV screen.
2 Press the LINK MENU button on the TV Remote Control.
3 Operate with the control button on the TV Remote Control.
The items for Link Menu
Delete
Selects the method for deleting images from single or all
images (page 110).
Image Index
Slide show
Protect
Switches to the image index screen.
Protects all the images/cancels the protections of all the
images (page 109).
Specify Printing
Specifies/unspecifies DPOF on all the images (page 143).
Specifies the number of images to be printed.
Dates images or not.
Single-image
playback
Returns to the single-image screen.
Notes
• The operations available are restricted when the camera is connected to a TV using
an HDMI cable.
• Only TVs that support “BRAVIA” Sync can provide these operations. For details,
refer to the operating instructions supplied with the TV.
114
• If the camera performs unnecessary operations in response to the TV Remote
Control when the camera is connected to another manufacturer’s TV using an HDMI
connection, set [CTRL FOR HDMI] in the
Setup menu to [Off].
115
Changing your setup
Setting image size and image quality
Image size
MENU button t
1 t [Image size] t Select the desired size
[Aspect ratio]: [3:2]
L:14M
4592 × 3056 pixels
3408 × 2272 pixels
2288 × 1520 pixels
M:7.7M
S:3.5M
[Aspect ratio]: [16:9]
L:12M
4592 × 2576 pixels
3408 × 1920 pixels
2288 × 1280 pixels
M:6.5M
S:2.9M
Note
• When you select a RAW image with [Quality], the image size of the RAW image
corresponds to L. This size is not displayed on the LCD monitor.
Aspect ratio
MENU button t
1 t [Aspect ratio] t Select the desired
ratio
3:2
A normal ratio.
An HDTV ratio.
16:9
116
Quality
MENU button t
(RAW)
1 t [Quality] t Select the desired setting
File format: RAW (raw data)
This format does not perform any digital processing on the
images. Select this format to process images on a computer
for professional purposes.
• The image size is fixed to the maximum size. The image
size is not displayed on the LCD monitor.
(RAW &
JPEG)
File format: RAW (raw data) + JPEG
A RAW image and a JPEG image are created at the same
time. This is suitable when you need two image files, a JPEG
for viewing, and a RAW for editing.
• The image quality is fixed to [Fine] and the image size is
fixed to [L].
(Fine)
File format: JPEG
The image is compressed in the JPEG format when recorded.
Since the compression rate of
(Standard)
(Standard) is higher than
that of
of
(Fine), the file size of is smaller than that
. This will allow more files to be recorded on one
memory card, but the image quality will be lower.
Note
• For details on the number of images that can be taken when the image quality is
About RAW images
You need the “Image Data Converter SR” software included on the CD-ROM
(supplied) in order to open a RAW image recorded on this camera. With this software,
a RAW image can be opened and converted to a common format, such as JPEG or
TIFF, and its white balance, color saturation, contrast, etc., can be readjusted.
• The RAW format image cannot be printed using a DPOF (print) designated printer
or a PictBridge compliant printer.
• You cannot verify the effects of D-Range Optimizer other than those of
(Standard) if you play back and enlarge an image recorded in RAW format.
117
Setting the method for recording on a
memory card
Selecting the method for assigning file numbers to images
MENU button t
2 t [File number] t Select the desired
setting
Series
The camera does not reset numbers and assigns numbers to
files in sequence until the number reaches “9999.”
Reset
The camera resets numbers in the following cases and assigns
numbers to files from “0001.” When the recording folder
contains a file, a number one higher than the largest number
is assigned.
– When the folder format is changed.
– When all the images in the folder are deleted.
– When the memory card is replaced.
– When the memory card is formatted.
Selecting the folder name format
The recorded images are stored in automatically-created folders in the
DCIM folder of the memory card.
MENU button t
2 t [Folder name] t Select the desired
setting
Standard form
The folder name format is as follows: folder number +
MSDCF.
Example: 100MSDCF
Date form
The folder name format is as follows: folder number + Y (the
last digit)/MM/DD.
Example: 10100405 (Folder name: 100, date: 04/05/2010)
118
Creating a new folder
You can create a folder in a memory card for recording images.
A new folder is created with a number incremented one higher than the
largest number currently used, and the folder becomes the current recording
folder.
MENU button t
2 t [New folder]
Selecting the recording folder
When a standard form folder is selected and there are two or more folders,
you can select the recording folder to be used to record images.
MENU button t
2 t [Select folder]t Select the desired
folder
Note
• You cannot select the folder when you select the setting [Date form].
Formatting the memory card
Note that formatting irrevocably erases all data on a memory card,
including protected images.
MENU button t
1 t [Format]t [OK]
Notes
• During the format, the access lamp lights up. Do not eject the memory card while the
lamp is lit.
• Format the memory card using the camera. If you format it on a computer, the
memory card may not be usable with the camera, depending on the format type used.
• Formatting may take several minutes depending on the memory card.
119
Changing the noise reduction setting
Disabling the noise reduction during long exposure
shootings
When you set the shutter speed to a second or longer (Long exposure
shooting), noise reduction is turned on for the same duration that the shutter
is open.
This is to reduce the grainy noise typical in a long exposure. When noise
reduction is in progress, a message appears and you cannot take another
picture. Select [On] to prioritize the image quality. Select [Off] to prioritize
the timing of shooting.
MENU button t
2 t [Long exp.NR] t [Off]
Notes
• Noise reduction is not performed on continuous shooting, continuous bracketing, or
continuous self-timer images even when it is set to [On].
• When the exposure mode is set to AUTO or Scene Selection, you cannot turn off
noise reduction.
Disabling the noise reduction at high ISO sensitivity
settings
When shooting with the ISO set at 1600 or above, the camera reduces the
noise that becomes more noticeable when the camera sensitivity is high.
Select [On] to prioritize the image quality. Select [Off] to prioritize the
timing of shooting.
MENU button t
2 t [High ISO NR] t [Off]
Notes
• Noise reduction is not performed on continuous shooting, continuous bracketing, or
continuous self-timer images even when it is set to [On].
• When the exposure mode is set to AUTO or Scene Selection, you cannot turn off
noise reduction.
120
Changing the functions of the control dial
Changing the function of the control dial
When the recording mode is M (Manual exposure), you can set the camera
so that the adjustable item (the shutter speed or the aperture value) can be
selected using only the control dial.
It is convenient if you select the most commonly-used item when adjusting
the exposure.
MENU button t
1 t [Ctrl dial setup] t Select the desired
setting
121
Changing other settings
Setting the sound on/off
Selects the sound produced when the shutter is locked, during self-timer
countdown, etc.
MENU button t
3 t [Audio signals] t Select the desired
setting
Selecting the background color of the screen display
You can select the background color of the LCD monitor from [Black],
[White], [Brown], or [Pink].
MENU button t
1 t [Display Color] t Select the desired
setting
Removing the Help Guide from the screen
You can turn off the Help Guide that is displayed when you operate the
camera. This is convenient when you want to perform the next operation
quickly.
MENU button t
1 t [Help Guide disp.] t [Off]
Setting the time to turn the camera to the power save mode
You can set different time intervals for the camera to switch to power save
mode (Power save) for the Live View (LV) and viewfinder modes (OVF).
Pressing the shutter button halfway down returns the camera to the
shooting mode.
MENU button t
1 t [Power Save (LV)] or [Power Save
(OVF)] t Select the desired time
122
Note
• Regardless of the setting here, the camera turns to power save mode after 30 minutes
when the camera is connected to a TV or the drive mode is set to (Remote
Commander).
Setting the date
MENU button t
2 t [Date/Time setup] t Set up the date
and time
Selecting the language
MENU button t 2 t [ Language] t Select the language
123
Setting the LCD monitor
Setting the brightness of the LCD monitor manually
The brightness of the LCD monitor is automatically adjusted to the
You can set the brightness of the LCD monitor manually.
MENU button t
1 t [LCD brightness] t [Manual] t
Select the desired setting
Notes
• When it is set to [Auto], do not cover the light sensor with your hand and so on.
• When using the camera with the AC-PW10AM AC Adaptor (sold separately), the
brightness of the LCD monitor is always set to the brightest setting even if you select
[Auto].
Setting the displayed time of the image right after shooting
(Auto review)
You can check the recorded image on the LCD monitor right after the
shooting. You can change the displayed time.
MENU button t
1 t [Auto review] t Select the desired
setting
Note
• In auto review, the image will not be displayed in the vertical position even if
[PlaybackDisplay] is set to [Auto rotate] (page 102).
124
Keeping the LCD monitor tuned on while looking into the
viewfinder
When the LIVE VIEW/OVF switch is set to “OVF,” looking into the
viewfinder turns off the LCD monitor.
In the default setting, while looking into the viewfinder, the LCD monitor
is turned off to prevent the battery pack from wearing down.
If you want to turn on the LCD monitor while looking into the viewfinder,
select [Off].
MENU button t
1 t [Auto off w/ VF] t [Off]
125
Confirming the version of the camera
Displaying the version
Displays the version of your camera. Confirm the version when a firmware
update is released.
MENU button t
3 t [Version]
Note
• An update can be performed only when the battery level is
(three remaining
battery icons) or more. We recommend that you use a sufficient battery or the AC-
PW10AM AC Adaptor (sold separately).
126
Resetting to the default
You can reset the main functions of the camera.
MENU button t
3 t [Reset default] t [OK]
The items to be reset are as follows.
Items
Reset to
Exposure compensation (86)
Recording information display (69)
Playback display (102)
0.0
Graphic Display
Single-image screen (with recording
information)
Drive mode (97)
Single-shot adv.
AUTO
Flash mode (82)
Autoflash or Flash Off
Multi segment
AF-A
Metering mode (89)
Autofocus mode (78)
White balance (91)
Custom white balance (92)
D-RangeOptimizer (94)
Creative Style (94)
AWB (Auto white balance)
5500K
Standard
Standard
Recording menu
Items
Reset to
L:14M
3:2
Image size (116)
Aspect ratio (116)
Quality (117)
Fine
0.0
Flash compens. (88)
AF illuminator (84)
SteadyShot (45)
Color Space (96)
Long exp.NR (120)
High ISO NR (120)
Auto
On
sRGB
On
On
127
Custom menu
Items
Reset to
On
Eye-Start AF (67)
Ctrl dial setup (121)
Red eye reduc. (84)
Auto review (124)
Shutter speed
Off
2 sec
On
Playback menu
Items
Reset to
Off
Specify Printing – Date imprint (147)
Slide show – Interval (105)
Slide show – Repeat (105)
PlaybackDisplay (102)
3 sec
Off
Auto rotate
Setup menu
Items
Reset to
Auto
LCD brightness (124)
CTRL FOR HDMI (114)
Display Color (122)
Help Guide disp. (122)
File number (118)
20 sec
10 sec
On
White
On
Series
Folder name (118)
Standard form
Mass Storage
On
Audio signals (122)
128
Viewing images on a computer
Copying images to your computer
This section describes how to copy images in a memory card to a computer
connected using a USB cable.
Recommended computer environment
The following environment is recommended for a computer connected to
the camera to import images.
x Windows
OS (pre-installed): Windows XP*1 SP3/Windows Vista*2 SP2/Windows 7
• Operation is not assured in an environment based on an upgrade of the
operating systems described above or in a multi-boot environment.
*1 64-bit editions and Starter (Edition) are not supported.
*2 Starter (Edition) is not supported.
USB jack: Provided as standard
x Macintosh
OS (pre-installed): Mac OS X (v10.4, 10.5, 10.6)
USB jack: Provided as standard
Notes on connecting your camera to a computer
• Operations are not guaranteed for all the recommended computer environments
mentioned above.
• If you connect two or more USB devices to a single computer at the same time, some
devices, including your camera, may not operate, depending on the types of USB
devices you are using.
• Operations are not guaranteed when using a USB hub or an extension cable.
• Connecting your camera using a USB interface that is compatible with Hi-Speed
USB (USB 2.0 compliant) allows advanced transfer (high speed transfer) as this
camera is compatible with Hi-Speed USB (USB 2.0 compliant).
• When your computer resumes from a suspend or sleep mode, communication
between your camera and your computer may not recover at the same time.
129
Stage 1: Connecting the camera and your computer
1 Insert a memory card with recorded images into the camera.
2 Select the type of memory card you want to copy images from
using the memory card switch.
3 Insert the sufficiently charged battery pack in the camera, or
connect the camera to a wall outlet (wall socket) with the AC
Adaptor (sold separately).
• When you copy images to your computer using an insufficiently charged
battery pack, copying may fail or image data may become corrupted if the
battery pack shuts down too soon.
4 Turn on the camera and the computer.
5 Check that [USB connection] in
3 is set to [Mass Storage].
6 Connect the camera and your
computer.
1 To the USB
terminal
The AutoPlay wizard appears on the
desktop.
USB cable
2 To the
USB terminal
130
Stage 2: Copying images to a computer
For Windows
This section describes an example of copying images to a “Documents”
(For Windows XP: “My Documents”) folder.
When you use the supplied “PMB” software, you can copy images easily
1 Click [Open folder to view files]
(For Windows XP: [Open folder to
view files] t [OK]) as the wizard
screen appears automatically on
the desktop.
• When the wizard screen does not
appear, click [Computer] (For
Windows XP: [My Computer]) t
[Removable Disk].
2 Double-click [DCIM].
• You can also import images directly using “PMB.”
3 Double-click the folder where the
image files you want to copy are
stored.
Then, right-click an image file to
display the menu and click
[Copy].
• On the storage destination of the image
files, see page 135.
131
4 Double-click the [Documents]
folder. Then, right-click on the
“Documents” window to display
the menu and click [Paste].
The image files are copied to the
“Documents” folder.
• When an image with the same file
name exists in the copy destination
folder, the overwrite confirmation
message appears. When you overwrite
an existing image with a new one, the
original file data is deleted. To copy an
image file to the computer without
overwriting, change the file name to a
different name and then copy the image
file. However, note that if you change
the file name, you may not be able to
play back that image with your camera
For Macintosh
1 Double-click the newly recognized icon t [DCIM] t the
folder where the images you want to copy are stored.
2 Drag and drop the image files to the hard disk icon.
The image files are copied to the hard disk.
132
Viewing images on your computer
For Windows
This section describes the procedure for viewing copied images in the
“Documents” (For Windows XP: “My Documents”) folder.
To view RAW images, the supplied “Image Data Converter SR” software
is required (page 140).
1 Click [Start] t [Documents].
• If you are using Windows 2000,
double-click [My Documents] on the
desktop.
2 Double-click the desired image file.
The image is displayed.
For Macintosh
Double-click the hard disk icon t the desired image file to open
the image file.
Deleting the USB connection
Perform each procedure for Windows or Macintosh listed below
beforehand when:
• Disconnecting the USB cable.
• Removing the memory card.
• Turning off the camera.
133
x For Windows
Double-click
on the tasktray, then click
(USB Mass Storage Device)
t [Stop]. Confirm the device on the confirmation window, then click
[OK].
The device is disconnected.
x For Macintosh
Drag and drop the drive icon or the icon of the memory card to the
“Trash” icon.
The camera is disconnected from the computer.
134
Image file storage destinations and file names
The image files recorded with your camera are grouped as folders on the
memory card.
Example: viewing folders on Windows Vista
AFolders containing image data recorded
using this camera. (The first three digits
show the folder number.)
BYou can create a folder in date form
• You cannot record/play back any images in
the “MISC” folder.
• Image files are named as follows. ssss
(file number) stands for any number within
the range of 0001 to 9999. The numerical
portions of the name of a RAW data file and
its corresponding JPEG file are the same.
– JPEG files: DSC0ssss.JPG
– JPEG files (Adobe RGB):
_DSCssss.JPG
– RAW data file (other than Adobe RGB):
DSC0ssss.ARW
– RAW data file (Adobe RGB):
_DSCssss.ARW
• The extension may not be displayed
depending on the computer.
Copying images stored on a computer to a memory card
and viewing the images
This section describes the process using a Windows computer as an
example. Step 1 is not necessary if the file name has not been changed.
When you use the supplied “PMB” software, you can copy images easily
135
1 Right-click the image file, then
click [Rename]. Change the file
name to “DSC0ssss.”
• Enter a number from 0001 to 9999 for
ssss.
• If the overwrite confirmation message
appears, enter a different number.
• An extension may be displayed
depending on the computer settings.
The extension for images is JPG. Do
not change the extension.
2 Copy the image file to the
memory card folder in the
following order.
1 Right-click the image file, then click
[Copy].
2 Double-click [Removable Disk] in
[Computer] (For Windows XP: [My
Computer]).
3 Right-click the [sssMSDCF]
folder in the [DCIM] folder, then click
[Paste].
• sss stands for any number within
the range of 100 to 999.
Notes
• You may be unable to play back some images depending on the image size.
• When an image file has been processed by a computer or when the image file was
recorded using a model other than that of your camera, playback on your camera is
not guaranteed.
copy the image file.
136
Using the software
To utilize images recorded with the camera, the following software is
provided:
• Sony Image Data Suite
“Image Data Converter SR”
“Image Data Lightbox SR”
• “PMB” (Picture Motion Browser)
Note
• “PMB” is not compatible with Macintosh computers.
Recommended computer environment
x Windows
Recommended environment for using “Image Data Converter SR Ver.3”/
“Image Data Lightbox SR”
OS (pre-installed): Microsoft Windows XP*1 SP3/Windows Vista*2 SP2/
Windows 7
*1 64-bit editions and Starter (Edition) are not supported.
*2 Starter (Edition) is not supported.
CPU/Memory: Pentium 4 or faster is recommended, RAM 1 GB or more is
recommended.
Display: 1024 × 768 dots or more
Recommended environment for using “PMB”
OS (pre-installed): Microsoft Windows XP*1 SP3/Windows Vista*2 SP2/
Windows 7
*1 64-bit editions and Starter (Edition) are not supported. Windows Image
Mastering API (IMAPI) Ver.2.0 or later is required to use the function
for creating discs.
*2 Starter (Edition) is not supported.
CPU/Memory: Pentium III 500 MHz or faster, 256 MB of RAM or more
(Recommended: Pentium III 800 MHz or faster and 512 MB of RAM or
more)
Hard Disk: Disk space required for installation—500 MB or more
Display: 1024 × 768 dots or more
137
x Macintosh
Recommended environment for using “Image Data Converter SR Ver.3”/
“Image Data Lightbox SR”
OS (pre-installed): Mac OS X (v10.4, v10.5, v10.6 (Snow Leopard))
CPU: Power PC G4/G5 series (1.0 GHz or faster is recommended)/Intel
Core Solo/Core Duo/Core 2 Duo or faster
Memory: 1 GB or more is recommended.
Display: 1024 × 768 dots or more
Installing the software
x Windows
• Log on as Administrator.
1 Turn on your computer, and insert
the CD-ROM (supplied) into the
CD-ROM drive.
The installation menu screen appears.
• If it does not appear, double-click
[Computer] (For Windows XP: [My
Computer]) t
(SONYPMB) t
[Install.exe].
• Under Windows Vista, the AutoPlay
screen may appear. Select “Run
Install.exe” and follow the instructions
that appear on the screen to proceed
with the installation.
2 Click [Install].
• Verify that both “Sony Image Data Suite” and “PMB” are checked and
follow the instructions on the screen.
138
3 Remove the CD-ROM after the installation is complete.
The following software is installed and shortcut icons appear on the desktop.
“Image Data Converter SR”
“Image Data Lightbox SR”
“PMB”
“PMB Launcher”
“PMB Help”
x Macintosh
• Log on as Administrator.
1 Turn on your Macintosh computer, and insert the CD-ROM
(supplied) into the CD-ROM drive.
2 Double-click the CD-ROM icon.
3 Copy the [IDS_INST.pkg] file in the [MAC] folder to the hard
disk icon.
4 Double-click the [IDS_INST.pkg] file in the copy-to folder.
• Follow the instructions on the screen to complete the installation.
Note
• When the restart confirmation message appears, restart the computer following the
instructions on the screen.
139
Using “Image Data Converter SR”
Note
• If you save an image as RAW data, the image is saved in the ARW2.1 format.
With “Image Data Converter SR” you can:
• Edit images recorded in RAW format with various corrections, such as
tone curve, and sharpness.
• Adjust images with white balance, exposure, and creative style, etc.
• Save the images displayed and edited on a computer. You can either save
the image as RAW format or save it in the general file format.
• For details on “Image Data Converter SR,” refer to Help.
To start Help, click [Start] t [All Programs] t [Sony Image Data Suite]
t [Help] t [Image Data Converter SR Ver.3].
The support information for the “Sony Image Data Suite” (English only):
http://www.sony.co.jp/ids-se/
To start up/exit “Image Data Converter SR”
x Windows
Double-click the shortcut of “Image Data Converter SR Ver.3” on the
desktop.
When starting up from the Start menu, click [Start] t [All Programs] t
[Sony Image Data Suite] t [Image Data Converter SR Ver.3].
To exit, click the
button on the upper-right corner of the screen.
x Macintosh
Double-click [Image Data Converter SR Ver.3] in the [Sony Image Data
Suite] folder from the [Applications] folder.
To exit, click a quit item from the [IDC SR] menu.
Using “Image Data Lightbox SR”
With “Image Data Lightbox SR” you can:
• Display and compare RAW/JPEG images recorded with this camera.
• Rate the images on a scale of five.
• Set color labels and so on.
140
• Display an image with “Image Data Converter SR” and make adjustments
to it.
• For details on “Image Data Lightbox SR,” refer to Help.
To start Help from the Start menu, click [Start] t [All Programs] t
[Sony Image Data Suite] t [Help] t [Image Data Lightbox SR].
To start up/exit “Image Data Lightbox SR”
x Windows
Double-click [Image Data Lightbox SR] on the desktop.
When starting up from the Start menu, click [Start] t [All Programs] t
[Sony Image Data Suite] t [Image Data Lightbox SR].
To exit, click the
button on the upper-right corner of the screen.
The dialogue used for saving a collection appears.
x Macintosh
Double-click [Image Data Lightbox SR] in the [Sony Image Data Suite]
folder from the [Applications] folder.
To exit, click a quit item from the [Image Data Lightbox SR] menu.
Using “PMB”
Note
• “PMB” is not compatible with Macintosh computers.
With “PMB” you can:
• Import images shot with the camera and display them on the computer.
• Organize images on the computer on a calendar by shooting date to view
them.
• Retouch (Red Eye Correction, etc.), print, and send still images as e-mail
attachments, change the shooting date and more.
• Print or save still images with the date.
• Create a data disc using a CD burner drive or DVD burner drive.
• For details on “PMB,” refer to “PMB Help.”
To start “PMB Help,” double-click the shortcut of
(PMB Help) on the
desktop. When starting up from the start menu, click [Start] t [All
Programs] t [PMB] t [PMB Help].
141
To start up/exit “PMB”
Double-click the
(PMB) icon on the desktop.
Or, from the Start menu: Click [Start] t [All Programs] t [PMB] t
[PMB].
To exit the “PMB,” click
button on the upper-right corner of the screen.
The support information for the “PMB” (English only):
http://www.sony.co.jp/pmb-se/
Note
• The confirmation message of the Information tool appears on the screen when
starting “PMB” for the first time. Select [Start]. This function informs you of news,
such as software updates. You can change the setting later.
142
Printing images
Specifying DPOF
Using the camera, you can specify the images and the number of images to
print before you print images at a shop or with your printer. Follow the
procedure below.
DPOF specifications are left with images after printing. It is recommended
that you unspecify them after printing.
Specifying /unspecifying DPOF on selected images
DPOF specifications can be operated either using the Fn button or the
MENU button. Here operation using the Fn button is described.
1 Fn button t [Specify Printing] t [DPOF setup] t [Marked
images] t [OK]
2 Select the image with b/B on the control button.
3 Select the number of sheets with the center of the control
button.
• To unspecify DPOF, set the number to “0.”
4 Press the Fn button.
5 Select [OK] with v on the control button, then press the center
of the control button.
Notes
• You cannot specify DPOF on RAW data files.
• You can specify any number up to 9.
Specifying/unspecifying DPOF on all the images
Fn button t [Specify Printing] t [DPOF setup] t [All images]
or [Cancel all] t [OK] t [OK]
143
• You can select a value for the number of images to be printed after you
have selected [All images]. The same value will be used for all images.
Dating images
You can date images when printing them. The position of the date (inside
or outside the image, character size, etc.) depends on your printer.
Fn button t [Specify Printing] t [Date imprint] t [On]
Note
• This function may not be provided, depending on the printer.
144
Printing images by connecting the
camera to a PictBridge compliant printer
Even if you do not have a computer, you
can print images shot using your camera
by connecting the camera directly to a
PictBridge compliant printer.
“PictBridge” is based on the CIPA
standard. (CIPA: Camera & Imaging
Products Association)
Note
• You cannot print RAW images.
Stage 1: Setting the camera
Note
• It is recommended to use the AC Adaptor (sold separately) to prevent the power
from turning off partway through printing.
1 MENU button t
3 t [USB connection] t [PTP]
2 Turn the camera off and insert the memory card that the images
have been recorded on.
3 Select the type of memory card you want to print images from
using the memory card switch.
145
Stage 2: Connecting the camera to the printer
1 Connect the camera to the printer.
1 To the
USB terminal
USB cable
2 To the
USB terminal
2 Turn on your camera and the printer.
The screen used for selecting images you want to print appears.
Stage 3: Printing
1 Select the image to print with b/B on the control button, then
press the center of the control button.
• To cancel, press the center again.
2 Repeat step 1 if you want to print other images.
3 Press the MENU button and set up each item.
4 Select [Print] t [OK] in the menu, then press the center of the
control button.
The image is printed.
• After the screen indicating that the print is completed appears, press the
center of the control button.
146
To cancel the print
During printing, pressing the center of the control button cancels the print.
Remove the USB cable or turn off the camera. When you want to print
again, follow the procedure (Stages 1 to 3) above.
PictBridge menu
Print
Prints the selected images. For details, see “Stage 3: Printing.”
Set print q’ty
You can specify the number of prints, up to 20. The same number of prints
is specified on all the selected images.
Paper size
Auto
Printer setup
89×127 mm
9×13cm/3.5"×5"
Hagaki
100×147 mm
10×15 cm
10×15cm
4"×6"
101.6×152.4 mm
105×148.5 mm
127×178 mm
216×279.4 mm
210×297 mm
297×420 mm
A6/4.1"×5.8"
13×18cm/5"×7"
Letter
A4/8.3"×11.7"
A3/11.7"×16.5"
Date imprint
Day and time
Date
Attaches the date and time.
Attaches the date.
Off
Does not attach the date.
Unmark all
After the message appears, select [OK], then press the center of the control
button. on each image is cleared after printing images. When you cancel
your specification without printing images, select this item.
147
Others
Sensitivity Range
0 to 18 EV (at ISO 100
equivalent)
Specifications
AF illuminator
Camera
Approx. 1 to 5 m (3.3 to
16.4 feet)
[System]
Camera Type
[Live View]
Type
Digital Single Lens Reflex
Camera with built-in flash
and interchangeable lenses
Pentamirror tilt mechanism
Image format
Exclusive image sensor for
Live View
Lens
A-mount lens
Metering method
1200-zone evaluative
metering
[Image sensor]
Total pixel number of camera
Approx. 14 900 000 pixels
Metering range
Effective pixel number of camera
Approx. 14 200 000 pixels
2 to 17 EV (Multi segment,
Center weighted, Spot) (at
ISO 100 with F1.4 lens)
Image format
23.5×15.7 mm (APS-C
format) Interlace scan
Primary Color
Frame Coverage
0.90
[Viewfinder]
Type
[SteadyShot]
Fixed eye-level penta-
Dach-mirror
System
Image sensor-shift
mechanism
Frame Coverage
0.95
SteadyShot Compensation capability
Approximately 2.5 to 3.5
EV decrease in shutter
speed (varies according to
shooting conditions and
lens used)
Magnification
0.74 × with 50 mm lens at
infinity, –1 m–1
Eye Relief Approximately 19.7 mm
from the eyepiece,
[Anti-Dust]
14.1 mm from the eyepiece
frame at –1 diopter
System
Charge protection coating
on Low-Pass Filter and
image sensor-shift
mechanism
(–1 m–1)
Dioptor Adjustment
–3.0 to +1.0 m–1
[Auto Focus System]
[Exposure control]
Metering Cell
SPC
System
TTL phase-detection
system, CCD line sensors
(9 points, 8 lines with
center cross-hair sensor)
148
Metering method
40-segment honeycomb-
[Recording media]
“Memory Stick PRO Duo”
pattern, the exclusive
image sensor for Live
View in Live View mode
media, SD memory card,
SDHC memory card
[LCD monitor]
Metering Range
2 to 20 EV (4 to 20 EV
with Spot metering), (at
ISO 100 with F1.4 lens)
2 to 17 EV in Live View
mode (on all metering
modes, at ISO 100 with
F1.4 lens)
LCD panel 6.7 cm (2.7 type) TFT
drive
Total number of dots
230 400 (960 × 240) dots
[Input/output terminals]
USB
miniB
ISO sensitivity (Recommended
HDMI
HDMI type C minijack
exposure index)
AUTO, ISO 100 to 3200
[Power, general]
Used battery pack
Exposure compensation
2.0 EV (1/3 EV step)
Rechargeable battery pack
NP-FH50
[Shutter]
Type
Electronically-controlled,
vertical-traverse, focal-
plane type
[Others]
PictBridge Compatible
Exif Print Compatible
Speed range 1/4000 second to 30
seconds, bulb, (1/3 EV
step)
PRINT Image Matching III
Compatible
Dimensions Approx. 128.1 × 97.1 ×
83.5 mm (5 1/8 × 3 7/8 ×
3 3/8 inches) (W/H/D,
Flash sync speed
1/160 second
excluding protrusions)
[Built-In-Flash]
Mass
Approx.549 g (1 lb 3.4 oz)
(including battery and
“Memory Stick PRO Duo”
media)
Approx. 497 g (1 lb 1.5 oz)
(camera only)
Flash guide number
GN 10 (in meters at ISO
100)
Recycling time
Approx. 4 seconds
Flash coverage
Operating temperature
0 to 40°C (32 to 104°F)
Covering 18 mm lens
(focal length that the lens
indicates)
File format JPEG (DCF Ver. 2.0, Exif
Ver. 2.21, MPF Baseline)
compliant, DPOF
Flash compensation
2.0 EV (1/3 EV step)
compatible
149
USB communication
Hi-Speed USB (USB 2.0
Capacity
Typical 6.1 Wh (900 mAh)
Minimum 5.9 Wh (870 mAh)
Maximum dimensions
compliant)
BC-VH1 Battery charger
Input rating 100 V – 240 V AC, 50/60
Hz, 4 W
Approx. 31.8 × 18.5 × 45.0
mm (1 5/16 × 3/4 × 1 13/16
inches) (W/H/D)
Output rating
Mass
Approx. 50 g (1.8 oz)
8.4 V DC, 0.28 A
Operating temperature range
0 to 40°C (32 to 104°F)
Design and specifications are subject
to change without notice.
Storage temperature range
–20 to +60°C (–4 to
+140°F)
On focal length
The picture angle of this camera is
narrower than that of a 35 mm-format
film camera. You can find the
approximate equivalent of the focal
length of a 35 mm-format film
camera, and shoot with the same
picture angle, by increasing the focal
length of your lens by half.
For example, by using a 50 mm lens,
you can get the approximate
equivalent of a 75 mm lens of a 35
mm-format film camera.
Maximum dimensions
Approx. 60 × 25 × 95 mm
(2 3/8 × 1× 3 3/4 inches)
(W/H/D)
Mass
Approx. 75 g (2.6 oz)
Rechargeable battery pack
NP-FH50
Used battery
Lithium-ion battery
Maximum voltage
DC 8.4 V
On image data compatibility
• This camera conforms with DCF
(Design rule for Camera File
system) universal standard
established by JEITA (Japan
Electronics and Information
Technology Industries
Nominal voltage
DC 6.8 V
Maximum charge current
1.75 A
Maximum charge voltage
DC 8.4 V
Association).
• Playback of images recorded with
your camera on other equipment
and playback of images recorded or
edited with other equipment on
your camera are not guaranteed.
150
Trademarks
is a trademark of Sony
Corporation.
• Adobe is a registered trademark or
a trademark of Adobe Systems
Incorporated in the United States
and/or other countries.
• D-Range Optimizer Advanced uses
technology provided by Apical
Limited.
• In addition, system and product
names used in this manual are, in
general, trademarks or registered
trademarks of their respective
developers or manufacturers.
However, the ™ or ® marks are not
used in all cases in this manual.
•
• “Memory Stick,”
Stick PRO,”
, “Memory
,
“Memory Stick Duo,”
, “Memory Stick
,
PRO Duo,”
“Memory Stick PRO-HG Duo,”
, “Memory
Stick Micro,” “MagicGate,” and
are trademarks of
Sony Corporation.
• “InfoLITHIUM” is a trademark of
Sony Corporation.
• “PhotoTV HD” is a trademark of
Sony Corporation.
• Microsoft, Windows, and Windows
Vista are either registered
trademarks or trademarks of
Microsoft Corporation in the
United States and/or other
countries.
• HDMI, the HDMI logo and High-
Definition Multimedia Interface are
trademarks or registered trademarks
of HDMI Licensing LLC.
• Macintosh and Mac OS are
trademarks or registered trademarks
of Apple Inc.
• PowerPC is a registered trademark
of IBM Corporation in the United
States.
• The SDHC logo is a trademark.
• MultiMediaCard is a trademark of
MultiMediaCard Association.
• Intel, Intel Core, MMX, and
Pentium are trademarks or
registered trademarks of Intel
Corporation.
151
Troubleshooting
If you experience trouble with your camera, try the following solutions.
authorized Sony service facility.
1
Check the following items.
2
Remove the battery pack, and insert the battery pack again after
about one minute, and turn on the power.
3
Reset the settings (page 127).
4
Consult your Sony dealer or local authorized Sony service facility.
Battery pack and power
The battery pack cannot be installed.
• As you insert the battery pack, use the tip of the battery pack to push the
The remaining battery indicator is incorrect, or sufficient remaining
battery indicator is displayed but the power runs out too quickly.
• This phenomenon occurs when you use the camera in an extremely hot or
Cannot turn on the camera.
152
The power turns off suddenly.
• If you do not operate the camera for given period of time, the camera turns
to power saving mode and nearly shuts down. To cancel the power save,
operate the camera, such as pressing the shutter button halfway down
The CHARGE lamp flashes when charging the battery pack.
• Remove and re-insert the battery pack correctly.
• Charge the battery pack under the suitable temperatures between 10 and
30°C (50 and 86°F).
Shooting images
Nothing is displayed on the LCD monitor in viewfinder mode when the
power is turned on.
• In the default setting, the LCD monitor will turn off if no operation is
registered for more than 10 seconds to minimize the battery consumption.
The image is not clear in the viewfinder.
• Adjust the diopter scale properly using the diopter-adjustment dial
No images in the viewfinder.
• The LIVE VIEW/OVF switch is set to “LIVE VIEW.” Set it to “OVF”
The image has not been recorded.
• A memory card is not inserted.
The shutter does not release.
• You are using a memory card with a write-protect switch, and the switch is
set to the LOCK position. Set the switch to the recording position.
• The position of the memory card switch is wrong. Set it to the correct
the following:
– Change the memory card.
153
• The shutter cannot be released when the subject is out of focus.
• When an astronomical telescope, etc., is attached to the camera, set the
recording mode to M and do your shooting.
Recording takes a long time.
malfunction.
large, the RAW mode shooting may take time.
The image is out of focus.
• The subject is too close. Check the minimum focal distance of the lens.
• You are shooting in manual focus mode, set the focus mode lever to AF
• When the focus mode switch is equipped with the lens, set it to AF.
• Ambient light is insufficient.
Eye-Start AF does not work.
• Press the shutter button halfway down.
The flash does not work.
• The flash mode is set to [Autoflash]. If you want to make sure the flash fires
Fuzzy specks appear in images shot using the flash.
• Dust in the air reflected the flash light and appeared in the image. This is
not a malfunction.
The flash takes too long to recharge.
• The flash has been fired in succession in a short period. When the flash has
been fired in succession, the recharging process may take longer than usual
to avoid overheating of the camera.
154
A picture taken with the flash is too dark.
• If the subject is beyond the flash range (the distance that the flash can
reach), the pictures will be dark because the flash light does not reach the
subject. If the ISO is changed, the flash range also changes with it
• In the following cases, the image may be dark. Remove these accessories,
then shoot.
– An ND filter or a PL filter.
– A diffuser.
– A wide panel for the HVL-F36AM flash.
The date and time are recorded incorrectly.
The aperture value and/or shutter speed flashes when you press the
shutter button halfway down.
• Since the subject is too bright or too dark, it is beyond the available range of
the camera. Adjust the setting again.
The image is whitish (Flare).
Blurring of light appears on the image (Ghosting).
• The picture was taken under a strong light source, and excessive light has
entered the lens. Attach a lens hood (sold separately).
The corners of the picture are too dark.
• If any filter or hood is used, take it off and try shooting again. Depending on
the thickness of the filter and improper attachment of the hood, the filter or
the hood may partially appear in the image. The optical properties of some
lenses may cause the periphery of the image to appear too dark (insufficient
light).
The eyes of the subject come out red.
• Get close to the subject, and shoot the subject within the flash range using
155
Dots appear and remain on the LCD monitor.
• You may reduce the effect of these issues using the “Pixel mapping”
function.
1 Set the LIVE VIEW/OVF switch to “LIVE VIEW.”
2 Attach the lens cap.
3 MENU button t
3 t [Pixel mapping] t [OK]
The image is blurred.
• The picture was taken in a dark location without the flash, resulting in
82).
The EV scale b B is flashing on the LCD monitor or in the viewfinder.
• The subject is too bright or too dark for the metering range of the camera.
The color of an image recorded in Live View mode is strange.
• In Live View mode, carefully check the image displayed on the LCD
monitor before shooting. The camera may not be able to recognize the color
of the image right after switching to the Live View mode. In such cases, the
expected result may not be obtained.
Viewing images
Your camera cannot play back images.
• When an image file has been processed by a computer or when the image
file was recorded using a model other than that of your camera, playback on
your camera is not guaranteed.
The image does not appear on the TV screen.
Deleting/Editing images
Your camera cannot delete an image.
• Cancel the protection (page 109).
156
You have deleted an image by mistake.
• Once you have deleted an image, you cannot restore it. We recommend that
You cannot mark a DPOF mark.
• You cannot mark DPOF marks on RAW images.
Computers
You do not know if the OS of your computer is compatible with the
camera.
Your computer does not recognize your camera.
• Check that the camera is turned on.
use the AC Adaptor (sold separately).
• Disconnect the USB cable, and connect it again firmly.
• Set [USB connection] to [Mass Storage] (page 130).
• Disconnect all equipment other than the camera, the keyboard and the
mouse from the USB jacks of your computer.
• Connect the camera directly to your computer without passing through a
USB hub or other device (page 129).
You cannot copy images.
• Make the USB connection by properly connecting the camera with your
computer (page 130).
• When you shoot images with a memory card formatted by a computer, you
may not be able to copy the images to a computer. Shoot using a memory
card formatted by your camera (page 119).
The image cannot be played back on a computer.
• If you are using “PMB,” refer to the “PMB Help.”
• Consult the computer or software manufacturer.
157
After making a USB connection, “PMB” does not start automatically.
You do not know how to operate the software (supplied).
• See help or the guide of each software.
Memory card
Cannot insert a memory card.
• Insertion direction of the memory card is wrong. Insert it in the correct
Cannot record on a memory card.
You have formatted a memory card by mistake.
• All the data on the memory card is deleted by formatting. You cannot
restore it.
“Memory Stick PRO Duo” media are not recognized by a computer with a
“Memory Stick” media slot.
• If “Memory Stick PRO Duo” media are not supported on your computer’s
“Memory Stick” media slot, connect the camera to the computer
(page 130). The computer will recognize the “Memory Stick PRO Duo”
media.
Printing
the following items.
The color of the image is strange.
• When you print the images recorded in Adobe RGB mode using sRGB
printers that are not compatible with Adobe RGB (DCF2.0/Exif2.21), the
158
Images are printed with both edges cut off.
• Depending on your printer, the left, right, top, and bottom edges of the
image may be cut off. Especially when you print an image shot with the
aspect ratio set to [16:9], the lateral end of the image may be cut off.
• When printing images using your own printer, cancel the trimming or
borderless settings. Consult the printer manufacturer as to whether the
printer provides these functions or not.
• When having images printed at a digital print shop, ask the shop whether
they can print the images without cutting off both edges.
Cannot print images with the date.
• This camera does not have a feature for superimposing dates on images.
However, because the images shot with the camera include information on
the recording date, you can print images with the date superimposed if the
printer or the software can recognize Exif information. For compatibility
with Exif information, consult the manufacturer of the printer or the
software.
• When you print images at a shop, images can be printed with the date if you
ask them to do so.
PictBridge compliant printer
For details, refer to the operating instructions supplied with the printer or
consult with the manufacturer of the printer.
A connection cannot be established.
• The camera cannot be connected directly to a printer that is not compliant
with the PictBridge standard. Consult the printer manufacturer as to
whether the printer is compliant with PictBridge or not.
• Set [USB connection] to [PTP] (page 145).
• Disconnect and connect the USB cable again. If an error message is
indicated on the printer, refer to the operating instructions supplied with the
printer.
159
Cannot print images.
• Check that the camera and the printer are properly connected using the USB
cable.
• RAW images cannot be printed.
• Images shot using cameras other than this camera or images modified with
a computer may not be printed.
“---- -- --” is printed on the date-inserted part of the image.
• Images that do not have the recording data/time information cannot be
printed with the date inserted. Set [Date imprint] to [Off] and print the
image again (page 147).
Cannot print the image at the size selected.
• Disconnect the USB cable and reconnect it whenever you change the paper
size after the printer has been connected to the camera.
• The print setting of the camera differs from that of the printer. Change the
Cannot operate the camera after canceling printing.
• Wait for a while as the printer is carrying out the cancellation. It may take
some time depending on the printer.
Others
The lens gets fogged.
• Moisture condensation has occurred. Turn off the camera and leave it for
The message “Set date and time?” appears when you turn on the camera.
• The camera has been left unused for sometime with a low battery or no
If the date setting is lost every time the battery pack is charged, consult your
Sony dealer or local authorized Sony service facility.
The number of recordable images does not decrease or decreases two at
a time.
• This is because the compression rate and the image size after compression
160
The setting is reset without the resetting operation.
• The battery pack was removed when the power switch was set to ON. When
removing the battery pack, make sure the camera is turned off and the
The camera does not work properly.
• Turn off the camera. Remove the battery pack and insert it again. If an AC
Adaptor (sold separately) is used, disconnect the power cord. If the camera
is hot, allow it to cool down before trying this corrective procedure. If the
camera does not work after doing these solutions, consult your Sony dealer
or local authorized Sony service facility.
The five bars of the SteadyShot scale flashes.
• The SteadyShot function does not work. You can continue to shoot but the
SteadyShot function will not work. Turn the camera off and on. If the
SteadyShot scale continues to flash, consult your Sony dealer or local
authorized Sony service facility.
“--E-” is indicated on the screen.
• Remove the memory card, and insert it again. If this procedure does not turn
off the indication, format the memory card.
161
If the message still appears,
change the memory card.
Warning messages
Card error
• An incompatible memory card is
inserted or the format has failed.
If the following messages appear,
follow the instructions below.
Incompatible battery. Use correct
model.
• An incompatible battery pack is
Reinsert “Memory Stick.”
Reinsert SD memory card.
• The inserted memory card
cannot be used in your camera.
• The memory card is damaged.
• The terminal section of the
memory card is dirty.
Set date and time?
• Set the date and time. If you
have not used the camera for a
long time, charge the internal
165).
SD memory card locked.
• You are using a memory card
with a write-protect switch, and
the switch is set to the LOCK
position. Set the switch to the
recording position.
Power insufficient
• You tried to perform [Cleaning
mode] when the battery level is
insufficient. Charge the battery
pack or use the AC Adaptor
(sold separately).
This “Memory Stick” is not
supported.
• Use “Memory Stick” media
available on this camera
Unable to use “Memory Stick.”
Format?
Unable to use SD memory card.
Format?
No “Memory Stick” inserted.
Shutter is locked.
No SD memory card inserted.
•
The memory card was formatted
on a computer and the file format
was modified.
Shutter is locked.
• No memory card of the type
selected using the memory card
switch is inserted. Insert a
memory card, or change the type
of the memory card using the
memory card switch.
Select [OK], then format the
memory card. You can use the
memory card again, however, all
previous data in the memory card
is erased. It may take a some time
to complete the format.
162
Processing...
Initializing USB connection...
• When Long exposure noise
reduction will be done for the
same amount of time that the
shutter was open. You cannot do
any further shooting during this
reduction.
• A USB connection has been
established. Do not disconnect
the USB cable.
Check the connected device.
• A PictBridge connection cannot
be established. Disconnect the
USB cable and connect it again.
Unable to display.
• Images recorded with other
cameras or images modified with
a computer may not be able to be
displayed.
Camera overheating. Allow it to
cool.
• The camera has become hot
because you have been shooting
continuously.
No lens attached. Shutter is
locked.
Turn the power off. Cool the
camera and wait until the camera
is ready to shoot again.
• The lens is not attached properly,
or the lens is not attached.
• When attaching the camera to an
astronomical telescope or
something similar, set the
recording mode to M.
Camera error
System error
• Turn the power off, remove the
battery pack, then re-insert it. If
the message appears frequently,
consult your Sony dealer or local
authorized Sony service facility.
No images
• There is no image in the memory
card.
Image protected
Unable to magnify.
Unable to rotate image.
• Images recorded with other cameras
may not be enlarged or rotated.
• You tried to delete protected
images.
Unable to print.
No images changed
• You tried to mark RAW images
with a DPOF mark.
• You attempted to protect images
or specified DPOF without
changing the specification of
those images.
163
Cannot create more folders.
• The folder with a name beginning
with “999” exists on the memory
card. You cannot create any
folders if this is the case.
Printing canceled
• The print job was canceled.
Disconnect the USB cable or
turn the camera off.
Unable to mark.
• You attempted to mark RAW
images on the PictBridge screen.
Printer error
• Check the printer.
• Check if the image you want to
print is corrupted.
Printer busy
• Check the printer.
164
On operating temperatures
Precautions
Your camera is designed for use
under the temperatures between 0 and
40°C (32 and 104°F). Shooting in
extremely cold or hot places that
exceed this range is not
Do not use/store the camera in
the following places
• In an extremely hot, dry or humid
place
recommended.
In places such as in a car parked in
the sun, the camera body may
become deformed and this may
cause a malfunction.
• Under direct sunlight or near a
heater
The camera body may become
discolored or deformed, and this
may cause a malfunction.
• In a location subject to rocking
vibration
• Near strong magnetic place
• In sandy or dusty places
Be careful not to let sand or dust get
into the camera. This may cause the
camera to malfunction, and in some
cases this malfunction cannot be
repaired.
On moisture condensation
If the camera is brought directly from
a cold to a warm location, moisture
may condense inside or outside the
camera. This moisture condensation
may cause a malfunction of the
camera.
How to prevent moisture
condensation
When bringing the camera from a
cold place to a warm place, seal the
camera in a plastic bag and allow it to
adapt to conditions at the new
location over about an hour.
If moisture condensation occurs
Turn off the camera and wait about an
hour for the moisture to evaporate.
Note that if you attempt to shoot with
moisture remaining inside the lens,
you will be unable to record clear
images.
On storing
Be sure to attach the lens cap or
body cap when not using the
camera. When attaching the body
cap, remove all the dust from the
cap before placing it on the camera.
When you purchase the DT 18 – 55
mm F3.5 – 5.6 SAM Lens Kit,
purchase the Rear Lens Cap ALC-
R55 also.
On the internal rechargeable
battery
This camera has an internal
rechargeable battery for maintaining
the date and time and other settings
regardless of whether the power is on
or off.
165
This rechargeable battery is
Or it may cause a malfunction of
your camera.
continually charged as long as you
are using the camera. However, if you
use the camera for only short periods,
it discharges gradually, and if you do
not use the camera at all for about 3
months it becomes completely
discharged. In this case, be sure to
charge this rechargeable battery
before using the camera.
However, even if this rechargeable
battery is not charged, you can still
use the camera as long as you do not
record the date and time. If the
camera resets the settings to the
defaults each time you charge the
battery, the internal rechargeable
battery may be dead. Consult your
Sony dealer or local authorized Sony
service facility.
• Do not use the camera near a
location that generates strong radio
waves or emits radiation. The
camera may not be able to record or
play back properly.
• Using the camera in sandy or dusty
locations may cause malfunctions.
• If moisture condensation occurs,
remove it before using the camera
• Do not shake or strike the camera.
In addition to malfunctions and an
inability to record images, this may
render the memory card unusable,
or cause image data breakdown,
damage or loss.
• Clean the flash surface before use.
The heat of flash emission may
cause dirt on the flash surface to
become discolored or to stick to the
flash surface, resulting in
Charging method of the internal
rechargeable battery
Insert a charged battery pack in the
camera, or connect the camera to a
wall outlet (wall socket) using the AC
Adaptor (sold separately), and leave
the camera for 24 hours or more with
the power off.
insufficient light emission.
• Keep the camera, supplied
accessories, etc., out of the reach of
children. A memory card, etc., may
be swallowed. If such a problem
occurs, consult a doctor
immediately.
Notes on recording/playback
• Before you record one-time events,
make a trial recording to make sure
that the camera is working
correctly.
• This camera is neither dust-proof,
nor splash-proof, nor water-proof.
• Do not look at the sun or a strong
light through a removed lens or the
viewfinder. This may cause
irrecoverable damage to your eyes.
166
J
L
F
M
H
N
I
168
O
P
Q
U
R
V
Viewing images on a TV screen
W
S
Z
169
170
|