ELECTRONIC CASH REGISTER
CAJA REGISTRADORA ELECTRONICA
MODEL
MODELO
XE-A201
INSTRUCTION MANUAL
MANUAL DE INSTRUCCIONES
How to Use the Instruction Manual
Printing a Document To print the current document, click the Print button
Finding words To find a complete word or part of a word in the current document, click here.
Paging through a document To go to the next page, click the > button. To go to the previous
page.
Using Acrobat Reader This manual is in the format of Acrobat Reader. For the details of how to
Browsing with bookmarks Bookmarks can mark parts of a document for quick access.
The scroll bar also enables you to page through the document.
The illustration above is a screen of Acrobat Reader 5.0.
CONTENTS
INTRODUCTION............................................................................................................................................1
IMPORTANT ..................................................................................................................................................1
CONTENTS....................................................................................................................................................2
1 External View ........................................................................................................................................4
2 Printer....................................................................................................................................................4
3 Mode Switch and Mode Keys................................................................................................................5
4 Keyboard...............................................................................................................................................5
5 Displays.................................................................................................................................................6
6 Drawer Lock Key...................................................................................................................................6
1 Basic Sales Entry Example .................................................................................................................12
2 Error Warning......................................................................................................................................13
3 Item Entries .........................................................................................................................................14
Single item entries........................................................................................................................14
Multiplication entries.....................................................................................................................15
Single item cash sale (SICS) entry...............................................................................................17
4 Displaying Subtotal..............................................................................................................................17
5 Finalization of Transaction ..................................................................................................................17
Cash or check sale that does not require tender entry.................................................................18
Charge (credit) sale......................................................................................................................18
Mixed-tender sale.........................................................................................................................18
6 Tax Calculation....................................................................................................................................19
Automatic tax................................................................................................................................19
Manual tax....................................................................................................................................19
Tax delete.....................................................................................................................................19
1 Auxiliary Entries...................................................................................................................................21
2 Auxiliary Payment Treatment ..............................................................................................................23
Received-on Account and Paid-out Entries..................................................................................24
1 Correction of the Last Entry (direct void).............................................................................................25
2 Correction of the Next-to-last or Earlier Entry (indirect void)...............................................................25
3 Subtotal Void.......................................................................................................................................26
4 Correction of Incorrect Entries not Handled by the Direct or Indirect Void Function...........................26
2
1 Date and Time Programming ..............................................................................................................27
2 Tax Programming for Automatic Tax Calculation Function.................................................................28
Tax programming using a tax rate................................................................................................28
1 Department Programming...................................................................................................................32
2 PLU (Price Look-Up) and Subdepartment Programming....................................................................33
3 Miscellaneous Key Programming........................................................................................................35
4 Text programming ...............................................................................................................................39
ADVANCED PROGRAMMING....................................................................................................................44
1 Register Number and Consecutive Number Programming.................................................................44
2 Electronic Journal (EJ) Programming..................................................................................................45
3 Various Function Selection Programming 1........................................................................................47
Print format...................................................................................................................................48
4 Various Function Selection Programming 2........................................................................................51
Power save mode.........................................................................................................................51
Logo message print format...........................................................................................................51
RS-232C interface........................................................................................................................52
Thermal printer density.................................................................................................................53
AUTO key programming...............................................................................................................54
5 Reading Stored Program.....................................................................................................................54
TRAINING MODE ........................................................................................................................................56
1 In Case of Power Failure.....................................................................................................................62
2 In Case of Printer Error .......................................................................................................................62
3 Cautions in Handling the Printer and Recording Paper.......................................................................62
4 Replacing the Batteries .......................................................................................................................63
5 Replacing the Paper Roll.....................................................................................................................63
6 Removing a Paper Jam.......................................................................................................................65
7 Cleaning the Print Head ......................................................................................................................66
8 Removing the Drawer..........................................................................................................................66
9 Opening the Drawer by Hand..............................................................................................................66
10 Before calling for service.....................................................................................................................67
Error code table............................................................................................................................67
MANUAL DE INSTRUCCIONES (VERSION EN ESPAÑOL)
3
PARTS AND THEIR FUNCTIONS
External View
1
Front view
Rear view
Customer display
(Pop-up type)
Operator display
Printer cover
Receipt paper
Power cord
Mode switch
Drawer
Keyboard
RS-232C connector
Drawer lock
Printer
2
The printer is one station type thermal printer, and therefore it does not require any
type of ink ribbon or cartridge.
Lift the rear of the printer cover to remove. To re-install, hook on the pawls on the
cabinet and close.
Caution: The paper cutter is mounted on the cover. Be careful not to cut
yourself.
Print head release lever
The print head can be lifted off the roller by the print head
release lever (light green lever on the right side of the
printer). Pulling the lever toward you moves the print head
away from the roller. If the paper becomes jammed, you
will need to use this lever to release the print head from
the paper to remove the jammed paper.
Take-up spool
Paper roll cradle
Print head
release lever
Do not attempt to remove the paper roll with
the head in the down position. This may result
in damage to the printer and print head.
4
Mode Switch and Mode Keys
3
The mode switch can be operated by inserting one of the two supplied mode keys - manager (MA) and operator
(OP) keys. These keys can be inserted or removed only in the “REG” or “OFF” position.
The mode switch has these settings:
OFF:
This mode locks all register operations. (AC power turns off.)
No change occurs to register data.
To take individual clerk X or Z reports, and to take flash reports.
It can be used to toggle receipt state “ON” and “OFF” by pressing
REG
OPX/Z
OFF
MGR
X1/Z1
X2/Z2
OP X/Z:
VOID
PGM
the
key.
R
REG:
PGM:
VOID:
For entering sales.
Manager key (MA)
Operator key (OP)
To program various items.
Enters into the void mode. This mode allows correction after
finalizing a transaction.
For manager’s entries. The manager can use this mode for an
override entry.
MGR:
X1/Z1:
X2/Z2:
To take the X/Z report for various daily totals
To take the X/Z report for periodic (weekly or monthly)
consolidation
Keyboard
4
Keyboard layout
PLU
DEPT DEPT
CLK
#
TAX AUTO
/SUB
#
SHIFT
@/FOR
CONV
CL
9
•
A
F
24
G
K
P
U
X
20
B
28
32
Q
TAX1 TAX2
SHIFT SHIFT
RA %1
7
4
1
8
5
2
4
3
2
1
8
7
6
5
12
11
10
9
L
27
M
16
15
14
13
V
Y
19
C
23
H
31
R
RCPT
CHK CH
%2
6
/PO
W
Z
NUMBER
–
18
D
22
I
26
N
30
S
MDSE #/TM
SBTL SBTL
VOID RFND
3
DC
SHIFT
17
E
21
J
25
O
29
T
ESC
CA/AT/NS
0
00
BS
SPACE
The small characters on the bottom or lower right in each key indicates functions or characters
Key names
@/FOR
•
Paper feed key
TAX Tax key
Multiplication key
Decimal point key
Clear key
TAX1 TAX2
SHIFT SHIFT
RA Received-on account key
Tax 1 and 2 shift keys
RCPT
/PO
AUTO Automatic sequence key
Receipt print/Paid-out key
CL
00
VOID Void key
Numeric keys
CHK Check key
0
~
9
PLU
ESC
Escape key
CH
Charge key
PLU/Subdepartment key
Department code entry key
Department shift key
/SUB
MDSE
SBTL
DEPT
#
CONV
Merchandise subtotal key
Conversion key
#/TM
SBTL
DEPT
SHIFT
Non-add code/Time display
/Subtotal key
%1 %2
Percent 1 and 2 keys
Total/Amount tender
/No sale key
CA/AT/NS
RFND Refund key
Discount key
CLK
#
Clerk code entry key
17
32
~
Department keys
1
16
5
Displays
5
Operator display
Customer display (Pop-up type)
PLU/SUB
Clerk code
DEPT REPEAT
RCPT
OFF
DC SHIFT NUMBER
Amount:
Appears in the far-right eight (max.) positions. When the amount is negative, the minus symbol “-”
appears before the amount.
Number of repeats for repetitive registrations:
The number of repeats is displayed, starting at “2” and incremental with each repeat. When you
..... ...
have registered ten times, the display will show “0.”(2 → 3
Receipt function status:
9 → 0 → 1 → 2
)
The indicator “_” appears in the RCPT OFF position when the receipt function is in the OFF
status.
Time:
Appears in the far-right six positions (hour-minute -“ ” or hour-minute -“ ”) in the OP X/Z, REG,
or MGR mode. “ ” is displayed in the morning (AM), and “ ” in the afternoon (PM). In the REG
or MGR mode, press the
key to display the time.
s
Machine state symbols
:
:
:
:
:
:
Appears during programming.
Appears when an error is detected.
Appears when the subtotal is displayed or when the amount tendered is smaller than the sales amount.
Appears when the key is pressed to calculate a subtotal in foreign currency.
V
Appears when a transaction is finalized by pressing the
,
A C c
or
key.
Appears when the change due amount is displayed.
: May appear in the far-left three positions at the timing of key entry when the electronic journal (EJ)
memory is full. (Depending on programming.)
:
:
:
Appears when the voltage of the installed batteries is under the required level. You must replace with
Appears when the batteries are not installed, or the installed batteries are dead. You must replace with
May appear right below the eighth and ninth places at the timing of finalization of a transaction when the
electronic journal (EJ) memory is nearly full.
Also appears right below the tenth place when power save mode is effective.
:
Appears when the print head release lever is in the lifted position.
: Appears when the paper is out.
Drawer Lock Key
6
This key locks and unlocks the drawer. To lock it, turn 90
degrees counterclockwise. To unlock it, turn 90 degrees
clockwise.
6
GETTING STARTED
Please follow the procedure shown below. The batteries are not installed and the power is OFF.
Installing the cash register
1
Find a stable surface where the cash register is not subject to water sources or direct sunlight near an
AC outlet.
Unpack the cash register and make sure all accessories are included. For details of accessories, please refer to
Initializing the cash register
2
In order for your cash register to operate properly, you must initialize it before programming for the first
time. Follow this procedure.
1. Insert the manager (MA) key into the mode switch and turn it to the REG
REG
OPX/Z
OFF
MGR
X1/Z1
X2/Z2
position.
VOID
PGM
2. Insert the plug into the AC outlet. The buzzer will sound three times.
IMPORTANT: This operation must be performed without batteries installed.
3. The cash register has now been initialized. The register display will show “0.00”
with “ ”.
If the buzzer does not sound when the plug is inserted, the initialization has not been done
successfully. (This will occur when the voltage is still high because you operated the cash register
just before starting initialization.) In this case, wait at least one minute after pulling out the plug,
and insert the plug again.
Installing batteries
3
Three new “AA” batteries must be installed in the cash register to prevent the data and
user-programmed settings from being erased from the memory, when the AC cord is accidentally disconnected
or in case of power failure. Once installed, the batteries will last approximately one year before needing
replacement. At this time, the “ ” symbol will appear on the display to indicate the batteries are low and must
be replaced within two days. If the no battery symbol “ ” appears, you must install the batteries at once.
Install three new “AA” batteries according to the procedure shown below with the AC cord connected and set to
the REG position:
1. Push the printer cover forward and detach it.
Be careful with the paper cutter, so as not to cut yourself.
2. Open the battery compartment cover next to the paper roll cradle.
7
3. Insert three new “AA” batteries as illustrated at the right.
When the batteries are properly installed “ ” on the display will disappear.
4. Close the battery compartment cover.
Be sure to observe precautions shown on page 1 when handling
batteries.
Installing a paper roll
4
Precaution: The paper cutter is mounted on the printer cover. Take caution when removing and
installing the cover.
The register can print receipts or journals. For the printer, you must install the paper roll provided with the
register, even when you program the register for not printing receipts or journals.
Install the paper roll according to the procedure shown below with the AC cord connected and the mode switch
set to the REG position:
1. Make sure the printer head release lever is positioned as illustrated at the
right.
2. Cut off approximately one revolution of the paper roll. Make sure
the paper end is cut as illustrated at the right.
Correct
Incorrect
3. Set the paper in paper roll cradle as illustrated at
To the printer
To the printer
the right.
Correct
Incorrect
4. Insert the end of the paper into the printer until it is caught by the printer
auto-feed and comes out of the printer at the top. If the printer does not
catch the paper, feed the paper while pressing the
key.
F
8
5. When not using the take-up spool (using as receipt paper):
• Cut off the excess paper using the edge of the inner cover, and replace
the printer cover. Press the
out of the printer cover.
key to make sure the paper end comes
F
If the paper end does not come out, open the printer cover, and
pass the paper end between the paper cutter and the paper guide
of the printer cover, and replace the cover.
When using the take-up spool (using as journal paper):
• Insert the end of the paper into the slit in the spool. (Press the
feed more paper if required.)
key to
F
• Wind the paper two or three turns around the spool shaft.
• Set the spool on the bearing, and press the
slack in the paper.
key to take up excess
F
• Replace the printer cover.
When using a paper roll as journal paper, you must change the
Selection Programming 1” section for changing the printing style.
Programming date, time and tax
5
The cash register provides text languages of English, French and Spanish. It is preset to English.
Before you can proceed with registration of sales, you must program:
• date
• time
• tax
Programming other necessary items
6
While the cash register is pre-programmed so it can be used with minimal setup, it does provide you
with optional functions. Before you start programming, please read through the sales operations section to
understand optional functions. The main optional functions are listed below.
• PLU (price lookup)
• Consecutive number
• Machine number
• Receipt or journal printing selection (factory setting: receipt printing)
• Power save mode (factory setting: goes into power save mode in 30 minutes)
• Electronic journal (EJ) memory size (factory setting: 1000 lines are storable. Up to 2000 lines)
The memory for electronic journal is commonly used for PLU. If you change the setting, the
maximum number of PLU code will decrease from 1200 to 200.
• Text programming for clerk name, department items, PLU/subdepartment items, logo messages printed on
the top or bottom of receipts, function texts and foreign currency symbol
9
• Split pricing entry
This is not factory preset. You must enable this function.
• Foreign currency conversion rate
You must set a conversion rate to use
• Preset unit price for departments and PLUs
key.
V
• Preset amount for
-
• Preset rates for
% &
You do not have to program these preset prices/amount/rates because you can enter when
registration. It might be convenient to preset so you do not have to re-enter every time.
• Amount entry digit limit for PO amount, RA amount, Manual tax amount
The factory setting makes the maximum amount you can enter. You can program to limit the amount.
• Key sequence for AUTO key
• RS-232C programming
• Specification of clerk to be trained
Department programming:
The cash register is pre-programmed for departments as follows:
Department:
Allow open price entry, taxable status- taxable 1 for department 1 to 10, and non taxable
for department 11 to 99
When you use department 11 or above, and/or you apply taxable status other than taxable 1 for department 1 to
10, you must change department settings. Please refer to the department programming section for
programming details.
Starting sales entries
7
Now you are ready for sales registration.
10
FOR THE OPERATOR
OVERVIEW OF FLOW OF DAILY SALES ENTRIES
Things to do before you start sales entries:
• Make sure the power cord is securely inserted into the AC outlet.
• Turn the mode switch to OP X/Z position, and check if time is correctly set.
• Replace the drawer, if removed for safety.
• Check if there is enough paper on roll.
• Select receipt ON/OFF function.
• Make any necessary programming for the day in PGM mode.
Things you can do for sales entries:
• Item entries
• Item repeat entries
• Item multiplication entries
• Single item cash sale (SICS), if programmed.
• Split pricing entries, if programmed.
• Displaying subtotals
• Cash/Check/Charge sale
• Cash tendering in a foreign currency, if the currency conversion rate is programmed.
• Manual tax entry
• Discount or premium using % & and
key
-
• Refund entry
• No sale
• Paid-out entries
• Received on account entries
• Printing non-add code number
• Making corrections
• Checking sales report
(page 21) sections and for details of correcting sales entries, refer to CORRECTION (page 25) section. For
details of reading sales information, refer to READING (X) AND RESETTING (Z) OF SALES TOTAL (page 57)
section.
Things to do after you close your store:
• Print sales reports, and clear sales data for the day.
• Print Electronic Journal (EJ) reports, and clear Electronic Journal (EJ) data, if necessary.
• Account money - comparing it with the amount in cash in drawer printed on the general report.
• Remove the drawer for safety.
• Turn the mode switch to OFF position.
For details of reading sales information, refer to READING (X) AND RESETTING (Z) OF SALES TOTAL (page
11
BASIC SALES ENTRY
Basic Sales Entry Example
1
On the below, basic sales entry example when selling department items by cash is shown. For operation
details, please refer to each section.
Mode switch setting
REG
OPX/Z
OFF
MGR
X1/Z1
X2/Z2
1. Turn the mode switch to the REG position.
Clerk assignment
2. Enter your clerk code. (For example, clerk code is 1. Press the 1 and L key in
VOID
PGM
this order.)
Item entries
3. Enter the price for the first department item. (For example, for 15.00, enter 15:, and press the
appropriate department key).
For department 17 to department 32, press the D key first before pressing the department key.
For department 33 and above, enter the department code using numeric keys, and press the d key,
then enter the price and press the d key again.
4. Repeat step 3 for all the department items.
Displaying subtotals
5. Press the s key to display the amount due.
Finalizing the transaction
6. Enter the amount received from the customer. (You can omit this step if the amount tendered is the same as
the subtotal.)
7. Press the A key, and the change due is displayed (when the amount received was not entered, the total
amount is displayed) and the drawer is opened.
8. Tear off the receipt and give it to the customer with his or her change.
9. Close the drawer.
Key operation example
Print
Clek
assignment
1 L
1500 !
2300 "
s
Graphic logo
Item
entries
Date/Time/Clerk code number
Register number
/Consecutive number/Clerk name
Displaying
subtotal
5000
Items
Price
Finalizing
the transaction
A
Not printed when
non-taxable items
only are sold.
Merchandise
subtotal
Tax amount
(In this example, the tax rate is set to 6.25%.)
Tax status (T1: taxable 1)
Total quantity
Total amount
Cash tendering/amount received
Change
12
Clerk assignment
Prior to any item entries, clerks must enter their clerk codes into the register. However, the code entry may not
be necessary when the same clerk handles the next transaction.
I Sign-on (in REG, MGR, VOID mode)
I Sign-off (in REG, MGR, VOID mode)
To display the signed-on clerk code
Clerk code 1 to 15
L L
L
Receipt ON/OFF function
When you use the printer to issue receipts, you can disable receipt printing in the REG mode to save paper
using the receipt ON/OFF function. To disable receipt printing, press the R key in the OP X/Z position. This
key toggles the receipt printing status ON and OFF.
To check the receipt printing status, turn the mode switch to the OP X/Z position or press the l key in the REG
mode. When the function is in the OFF status, the receipt off indicator “_” illuminates. Your register will print
reports regardless of the receipt state, so the paper roll must be installed even when the receipt state is “OFF”.
To issue a receipt when receipt ON/OFF function is set to OFF:
If your customer wants a receipt after you finalized a transaction with the receipt ON/OFF function being OFF
status, press the R key. This will produce a receipt. However, if more than 30 items were entered, the
receipt will be issued in the format of summary receipt print.
Power Save Mode
The register will enter into power save mode when no entries are performed based on the pre-programmed time
limit (by default, 30 minutes).
When your register goes to the power save mode, it will light off all the display except the decimal point at the
leftmost position. Your register will return to the normal operation mode when any key is pressed or a mode is
changed with the mode key. Please note when your register is recovered by a key entry, its key entry is invalid.
After the recovery, start the key entry from the beginning.
Error Warning
2
In the following examples, your register will go into an error state accompanied with a warning beep and the
error symbol “
” on the display. Clear the error state by pressing the l key and take proper action.
• You enter over a 32-digit number (entry limit overflow): Cancel the entry and re-enter the correct number.
• You make an error in key operation: Clear the error and continue operation.
• You make an entry beyond a programmed amount entry limit: Check to see if the entered amount is correct. If
it is correct, it can be rung up in the MGR mode. Contact your manager.
• An including-tax subtotal exceeds eight digits: Delete the subtotal by pressing the l key and press the A,
C or c key to finalize the transaction.
Error escape function
When you want to quit a transaction due to an error or an unforeseen event, use the error escape function as
shown below:
To clear the error state
Transaction
l
E E
The transaction is voided (treated as a subtotal void) and the receipt is issued by this function. If you have
already entered a tendered amount, the operation is finalized as a cash sale.
13
Item Entries
3
Single item entries
Department entries
For a merchandise classification, the cash register provides a maximum of 99 departments. To the
departments, group attributes such as taxable status are applied on items when they are entered.
• When using the department keys (for department 1 to 32)
For department 1 to 16, enter a unit price and press a department key. If you use a programmed unit price,
press a department key only.
For department 17 to 32, enter a unit price, press the D key and press a department key. If you use a
programmed unit price, press the D key and press a department key.
When using a programmed unit price
1
* Less than the programmed upper limit amounts
Unit price *1
(max. 7 digits)
Department key
When zero is entered, only the sales quantity is
added.
2
*D
2
* For the optional departments 17 through 32,
press the department shift key.
• When using the department code entry key
Enter a department(dept.) code and press the d key, then enter a unit price and press the d key again. If
the dept. code is programmed to preset price entry style and a unit price is preset, your cash register will finish
its registration operation.
When using a programmed unit price
1
* Less than the programmed upper limit
amounts
When zero is entered, only the sales
quantity is added.
Dept. code
(1 to 99)
Unit price *1
(max. 7 digits)
d
d
(In case only preset price entry is allowed.)
PLU/subdepartment entries
For another merchandise classification, the cash register provides a maximum of 1200 PLUs/subdepartments.
PLUs are used to call up preset prices by a code entry. Subdepartments are used to classify merchandise into
smaller groups under the departments. Every PLU and subdepartment has a code form 1 to 1200, and should
belong to a department to obtain attributes of that department.
The cash register is pre-programmed to PLU mode and zero for unit price. To use PLU entries, their preset unit
To use subdepartment entries, change to subdepartment mode for the PLU codes.
• PLU entries
PLU code
p
(1 to 1200)
• Subdepartment (open PLU) entries
* Less than the programmed upper limit
amounts
When zero is entered, only the sales
quantity is added.
PLU code
(1 to 1200)
Unit price *
(max. 7 digits)
p
p
14
Key operation example
Print
1200 (
500 D !
)
D "
Department entry
PLU entry
50 d 1500 d
33 d
2 p
Subdepartment
entry
11p1200p
A
Repeat entries
You can use this function for entering a sale of two or more of the same items. Repeat pressing a department
key, d key or p key as shown on key operation example.
Key operation example
Print
1200 ( (
500 D ! !
) )
D " "
Department entry
50 d 1500 d d
33 d d
2 p p
PLU entry
Subdepart-
ment entry
11 p 1200 p p
A
Multiplication entries
When you sell a large quantity of items, it is convenient to use the multiplication entry method. Enter quantity
using numeric keys and press the key before starting item entry as shown in the example below.
@
When programmed to allow fractional quantity entries, you can enter up to four integers and three
digit decimal, though the quantity is counted as one for sales reports. To enter a fractional quantity,
use the decimal point key between integer and decimal, as 7P5 for entering 7.5.
15
Key operation example
Print
3 @ 1200 (
5 @ 500 D !
3 @ )
5 @ D "
3 @ 50 d 1500 d
5 @ 33 d
Department entry
PLU entry
3 @ 2 p
5@ 11p1200p
A
Subdepartment
entry
Split pricing entries
This function is practical when the customer wants to purchase items normally sold in bulk.
To realize this function, you must change the programmed setting. Refer to “Various Function Selection
To make split pricing entries, follow the procedure below:
When using a programmed unit price
Selling q'ty
(Up to 4 digits)
Base q'ty
(Up to 2 digits)
Unit price
per base q'ty
Department key
@
@
D
Dept. code
Unit price
per base q'ty
d
d
(Only preset entry is allowed.)
PLU code
PLU code
p
p
Unit price
per base q'ty
p
Key operation example
Print
7 @ 10 @
600 *
Department entry
8 @ 12 @
35 p
A
PLU entry
16
Single item cash sale (SICS) entry
• This function is useful when a sale is for only one item and is for cash. This function is applicable only to those
departments that have been set for SICS or to their associated PLUs or subdepartments.
• The transaction is complete and the drawer opens as soon as you press the department key, d key or
key.
p
Key operation example
Print
250
For finishing
the transaction
,
If an entry to a department or PLU/subdepartment set for SICS follows the ones to departments or
PLUs/subdepartments not set for SICS, it does not finalize and results in a normal sale.
Displaying Subtotals
4
The register provides three types of subtotals:
Merchandise subtotal
Press the
the display.
key at any point during a transaction. The net sale subtotal - not including tax - will appear in
m
Taxable subtotal
Taxable 1 subtotal
Press the
and
keys in this order at any point during a transaction. The sale subtotal of
T
s
taxable 1 items will appear in the display.
Taxable 2 subtotal
Press the
and
keys in this order at any point during a transaction. The sale subtotal of
U
s
taxable 2 items will appear in the display.
Including-tax subtotal (full subtotal)
Press the
appear in the display.
key at any point during a transaction. The sale subtotal including tax and the symbol “ ” will
s
Finalization of Transaction
5
Cash or check tendering
Press the
key to get an including tax subtotal, enter the amount tendered by your customer, then press
s
the
key if it is a cash tender or press the
key if it is a check tender. When the amount tendered is
A
C
greater than the amount of the sale, your register will show the change due amount and the symbol “ ” will light
up. Otherwise the register will show a deficit and the symbol “ ” will light up. You now must make a correct
tender entry.
Cash tendering
Key operation example
Print
s
1000 A
17
Check tendering
Key operation example
Print
s
1000 C
Cash or check sale that does not require entry
Enter items and press the
display the total sale amount.
key if it is a cash sale or press the
if it is a check sale. Your register will
A
C
Key operation example
Print
300
+
p
A
10
In the case of check sale
Charge (credit) sale
Enter items and press the charge key ( ).
c
Key operation example
Print
2500
3250
+
*
c
Mixed-tender sale
You can perform mixed-tendering of check and cash, cash and charge, and check and charge.
Example: Your customer pays $9.50 in cash and $40.00 by charge for an including-tax subtotal of $49.50.
Key operation example
Print
s
950 A
c
18
Tax Calculation
Automatic tax
6
When the register is programmed with a tax rate (or tax table) and the tax status of an individual department is
set for taxable, it computes the automatic tax on any item that is entered directly into the department or indirectly
via a related PLU.
Example: Selling five $6.70 items (dept. 1, taxable 1) and one $7.15 item (PLU no. 85, taxable 2) for cash
Key operation example
Print
5
670
85
@
!
p
A
Manual tax
The machine allows you to enter tax manually after it finalizes an item entry.
Example: Selling an $8.00 item (dept. 12) for cash with 50 cents as tax
Key operation example
Print
800
50
(
t
A
Tax delete
You can delete the automatic tax on the taxable 1 and taxable 2 subtotal of each transaction by pressing the
key after the subtotal is displayed.
t
To delete taxable 1 subtotal, press
subtotal.
,
T s
to get taxable 1 subtotal, and then press
to delete the
t
To delete taxable 2 subtotal, press
subtotal.
,
U s
to get taxable 2 subtotal, and then press
to delete the
t
To delete all taxable (1-4) subtotal, press
,
,
T U s
and
in this order.
t
Example: Selling a $7.25 item (dept. 1, taxable 1) and another $5.15 item (dept. 11, taxable 2) for cash and
entering the sale as a non-taxable one
Key operation example
Print
725
515
!
/
T s
t
U s
t
A
19
Tax status shift
The machine allows you to shift the programmed tax status of each department or the PLU key by pressing the
and/or
key is resumed.
keys before those keys. After each entry is completed, the programmed tax status of each
T
U
Example: Selling the following items for cash with their programmed tax status reversed
• One $13.45 item of dept. 16 (non-taxable) as a taxable 1 item
• One $7.00 item of PLU no. 25 (non-taxable) as a taxable 1 and 2 item
• One $4.00 item of dept. 11 (taxable 2) as a non-taxable item
• Two $10.50 items of dept. 1 (taxable 1) as taxable 2 items
Key operation example
Print
1345
T <
T U p
25
400
T U !
U /
1050
!
A
When Canadian tax system is applied:
When using a tax status shift, the entry of a multi-taxable item for PST or GST will be prohibited.
Please see below:
In case of; Tax 1: PST, Tax 2: PST,
Tax 3: PST, Tax 4: GST
In case of; Tax 1: PST, Tax 2: PST,
Tax 3: GST, Tax 4: GST
Taxable 1 and 2 item ········· prohibited
Taxable 1 and 3 item········· prohibited
Taxable 2 and 3 item ········· prohibited
Taxable 1 and 4 item ············· allowed
Taxable 2 and 4 item ············· allowed
Taxable 3 and 4 item ············· allowed
Taxable 1 and 2 item ········· prohibited
Taxable 1 and 3 item ············· allowed
Taxable 2 and 3 item ············· allowed
Taxable 1 and 4 item ············· allowed
Taxable 2 and 4 item ············· allowed
Taxable 3 and 4 item ········· prohibited
20
OPTIONAL FEATURES
Auxiliary Entries
1
Discount and premium entries using the percent key
The percent key is used to apply a manually entered or preset discount or premium percent rate to individual
items or to a merchandise subtotal. In the default setting, you can manually enter a discount percent rate to
both individual items and merchandise subtotal. For manual entry of discount or premium percent rate, enter the
rate (up to 100.00) with the numeric keys (you need a decimal point when you enter a fractional percent rate),
and press a percent key. When using a preset rate (if programmed), just press a percent key.
When entry limit is programmed for a percent key, you can not enter a rate over the limit (error code 34 will
occur.)
Percent calculation for the merchandise subtotal
Key operation example
Print
4
140
570
@
>
*
m
10
%
A
Percent calculation for item entries
Key operation example
Print
800
+
P %
p
&
A
7
15
5
(When premium and 15% are
programmed for the key)
&
Discount and premium entries using the discount key
The discount key is used to apply a manually entered or preset discount or premium amount to individual items
or to a merchandise subtotal. In the default setting, you can manually enter a discount amount to both individual
items and merchandise subtotal. For manual entry of discount or premium amounts, enter the amount with the
numeric keys, and press the discount key. When using a preset amount (if programmed), press the discount
key.
When entry digit limit is programmed for the discount key, you can not enter an amount over the limit (error code
34 will occur.)
21
Discount for the merchandise subtotal
Key operation example
Print
575
+
p
m
-
A
10
100
Discount for item entries
Key operation example
Print
675
*
-
A
(When a discount amount of
$0.75 is programmed.)
Refund entries
For a refund of a department item, start with entering the refund amount and press the
key, then press the
f
corresponding department key (in case of department 17 to 32, press the
corresponding department key, and in case of department 33 to 99, enter the department code, press
key and press the
D
key
f
and the
key, enter the refund amount and press the
key).
d
d
For a refund of a PLU item, enter the PLU code and press the
For a refund of a subdepartment item, enter the PLU code and press the
refund amount and press the
key, then press the
key.
f
p
p
key and
key, then enter the
f
key.
p
Key operation example
Print
250
f +
33
100
f d
d
@
7
13
f p
p
A
15
150
f p
Non-add code number entries and printing
You can enter a non-add code number such as a customer’s code number and credit card number, a maximum
of 16 digits, at any point during the entry of a sale. The cash register will print it at once.
To enter a non-add code number, enter the number and press the
key.
s
22
Key operation example
Print
1230
s
1500
+
c
Auxiliary Payment Treatment
Currency conversion
2
The register allows payment entries in a foreign currency (only cash payment is available). Pressing the
creates a subtotal in the foreign currency.
key
V
When using a programmed currency conversion rate, press the
tendered amount in foreign currency if not exact amount payment, and press the
When making a manual entry of currency conversion rate, after item entries, enter the conversion rate (0.0000 to
key after item entries, then enter the
V
key.
A
9999.9999; you need a decimal point when you enter fractional conversion rate) and press the
enter the tendered amount in foreign currency if not exact amount payment, and press the
In both cases, the change due will be displayed in domestic currency, and when the amount tendered is short,
the deficit is shown in domestic currency.
key, then
key.
V
A
• Press the
key after pressing the
key to cancel payment in a foreign currency.
l
V
• If programmed, a foreign currency symbol is printed.
Applying preset conversion rate
Key operation example
Print
2300 +
4650 *
V
10000 A
Currency
conversion
Amount
tendered in
foreign currency
Domestic currency
Conversion rate
(When a currency conversion
rate 0.9350 is programmed for
the V key.)
Foreign currency
Domestic currency
Foreign currency symbol
(Printed if programmed)
Applying manual conversion rate
Key operation example
Print
2300 +
4650 *
1 P 275 V
10000 A
Conversion rate
23
Received-on Account and Paid-out Entries
When you receive on account from a customer or when you pay an amount to a vendor, it is a good idea to use
the
key or the
key respectively.
r
R
For the received-on-account (RA) entry, enter the amount, and press the
key.
r
For the paid-out (PO) entry, enter the amount and press the
key.
R
Cash tendering only available for RA and PO operation.
Key operation example
Print
12345
s
r
4800
No sale (exchange)
When you need to open the drawer with no sale, just press the
print “NO SALE” on the receipt or journal. If you let the machine print a non-add code number before pressing
key. The drawer will open and printer will
A
the
key, a no sale entry is achieved and a non-add code number is printed.
A
Automatic Sequencing Key (
key) Entries
3
a
You can achieve a programmed transaction simply by pressing the
key.
a
Key operation example
Print
a
(
= 500
)
a
* A
24
CORRECTION
Correction of the Last Entry (direct void)
1
If you make an incorrect entry relating to a department, PLU/subdepartment, percentage (
and
), discount
&
%
(
) or refund, you can void this entry by pressing the
-
key immediately after the incorrect entry.
v
Key operation example
Print
1250
+
v
2
p
v
600
'
&
v
,
-
v
328
28
250
f +
v
A
Correction of the Next-to-last or Earlier Entry (indirect void)
2
You can void any incorrect department entry, PLU/subdepartment entry or item refund entry made during a
transaction if you find it before finalizing the transaction (e.g. pressing the
applicable to department, PLU/subdepartment and refund entries only.
key). This function is
A
For the operation, press the
refund indirect void, press the
key just before you press a department key,
key or
key. For the
v
d
p
key after you press the
key.
v
f
Key operation example
Print
1310 +
1755 *
10 p
Correction
of a
department
entry
12 p
250 f +
825 *
1310 v +
12 v p
250 f v +
A
Correction
of a PLU entry
Correction of
a refund entry
25
Subtotal Void
3
You can void an entire transaction. Once subtotal void is executed, the transaction is aborted and the register
issues a receipt. This function does not work when more than 30 items have been entered.
Key operation example
Print
1310 "
"
1755 +
10 p
35 p
s
Subtotal void
v
s
Correction of Incorrect Entries not Handled by the Direct or Indirect Void
Function
4
Any errors found after the entry of a transaction has been completed or during an amount tendered entry cannot
be voided. These errors must be corrected by the manager.
The following steps should be taken:
1. If you are making the amount tendered entry, finalize the transaction.
2. Make correct entries from the beginning.
3. Hand the incorrect receipt to your manager for its cancellation.
26
FOR THE MANAGER
PRIOR TO PROGRAMMING
Before starting sales entries, you must first program necessary items so that the cash register suits your sales
manner. In this manual, there are three sections, BASIC FUNCTION PROGRAMMING where required items
must be programmed, AUXILIARY FUNCTION PROGRAMMING where you can program for more convenient
use of keys on the keyboard, and ADVANCED FUNCTION PROGRAMMING where various optional
programming features are provided. Find the appropriate features for your needs, and make the necessary
programming.
You can select the language of text (English, French or Spanish) printed on receipts or journals.
Procedure for programming
1. Check to see whether the paper roll is present in the machine. If there is not enough paper on the roll,
2. Put the manager key in the mode switch and turn it to the PGM position.
REG
OPX/Z
OFF
MGR
X1/Z1
X2/Z2
3. Program necessary items into the cash register.
Every time you program an item, the cash register will print the setting. Please
refer to print samples in each section.
VOID
PGM
4. If necessary, issue programming reports for your reference.
On the key operation example shown in the programming details, a numeric display such as
“6082000” indicates the parameter which must be entered using the corresponding numeric keys.
BASIC FUNCTION PROGRAMMING
(For Quick Start)
Date and Time Programming
1
Date
For setting the date, enter the date in 8 digits using the month-day-year (MM/DD/YYYY) format, then press the
s key.
Date(MM/DD/YYYY)
s
Key operation example
Print
08262002
s
(Aug. 26, 2002)
Date
You can use the date format of day-month-year (DD/MM/YYYY) or year-month-day (YYYY/MM/DD)
27
Time
For setting the time, enter the time in 4 digits using the 24-hour format. For example, when the time is set to
2:30 AM, enter 230; and when it is set to 2:30 PM, enter 1430.
Time(max. 4 digits in 24-hour format)
s
Key operation example
Print
1430
s
Time
In the display, current time is displayed in 12-hour format. For AM time, “ ” and for PM time “
”
will appear in the rightmost position with the current time. If you want to display time in the 24-hour
Tax Programming for Automatic Tax Calculation Function
2
The cash register can support US and Canadian tax systems. If you use the Canadian tax system,
you must first change the tax system, then program the tax rate or tax table and quantity for
doughnut exmpt which are described in this section. For changing your cash register’s tax system,
Before you can proceed with registration of sales, you must first program the tax that is levied in accordance
with the law of your state. The cash register comes with the ability to program four different tax rates. In most
states, you will only need to program Tax 1. However if you live in an area that has a separate local tax (such
as a Parish tax) or a hospitality tax, the register can be programmed to calculate these separate taxes.
When you program the tax status for a department, tax will be automatically added to sales of items assigned to
the department according to the programmed tax status for the department. You can also enter tax manually.
There are two tax programming methods. The tax rate method uses a straight percentage rate per dollar. The
tax table method requires tax break information from your states or local tax offices. Use the method which is
acceptable in your state. You can obtain necessary data for tax programming from your local tax office.
Tax programming using a tax rate
The percent rate specified here is used for tax calculation on taxable subtotals.
*Tax number (1 to 4)
s 9 @
@
When the lowest taxable amount is zero
Tax rate
(0.0000 to 100.0000)
Lowest taxable amount
(0.01 to 999.99)
@
s A
28
Example: Programming the tax rate 4% as tax rate 2 with tax exempt as 12¢
Key operation example Print
9
s @
2
4
@
@
12
s
A
• If you make an incorrect entry before pressing the third
it with the l key.
key in programming a tax rate, cancel
@
• You do not need to enter the trailing zeros of the tax rate (after the decimal point), but you do
need to enter the decimal for fractions.
The tax table (applicable to the add-on tax)
If you are in an area that uses a tax table for tax calculation, you can program the cash register accordingly. Tax
table programming can be performed for Tax 1 through Tax 4.
Sample tax table
New Jersey tax table: 6%
To program a tax table, first make a table like the right table shown above.
A: Difference between the
minimum breakpoint and
the next one (¢)
Range of sales amount
Taxes
Minimum breakpoint Maximum breakpoint
.00
.01
.11
.23
.39
.57
.73
.89
to
to
to
to
to
to
to
to
to
to
to
to
to
to
.10
.22
–
B: Non-cyclic
C: Cyclic-1
.01
.02
.03
.04
.05
.06
.07
.08
.09
.10
.11
.12
.13
T
Q
10 (0.11 - 0.01)
12 (0.23 - 0.11)
16 (0.39 - 0.23)
18 (0.57 - 0.39)
16 (0.73 - 0.57)
16 (0.89 - 0.73)
22 (1.11 - 0.89)
12 (1.23 - 1.11)
16 (1.39 - 1.23)
18 (1.57 - 1.39)
16 (1.73 - 1.57)
16 (1.89 - 1.73)
22 (2.11 - 1.89)
.38
.56
.72
.88
1.10
1.22
1.38
1.56
1.72
1.88
2.10
2.22
1.11 M1
1.23
1.39
1.57
D: Cyclic-2
1.73
1.89
2.11 M2
From the tax table, calculate the differences between a minimum break point and the next one (A). Then, from
the differences, find irregular cycles (B) and regular cycles (C and D). These cycles will show you the following
items necessary to program the tax table:
T: The tax amount collected on the minimum taxable amount (Q)
Q: The minimum taxable amount
M1: The maximum value of the minimum breakpoint on a regular cycle (C)
We call this point “MAX point.”
M2: The maximum value of the minimum breakpoint on a regular cycle (D)
We call this point “MAX point.”
M: Range of the minimum breakpoint on a regular cycle: difference between Q and M1 or between M1 and M2
29
*2
Rate
max. six digits
*1
One- or two-
digit number
M
s 8 @
@
@
@
max. four
digits
(0.0001 - 99.9999%)
Minimum breakpoint
max. five digits
T
Q
@
@
@ A
max. three
max. five
digits
digits
Repeat until the MAX point is entered.
The first figure to be entered depends upon whether the difference between a minimum
breakpoint to be entered and the preceding minimum breakpoint is not less than $1.00 or
more than 99¢. When the difference is not less than $1.00, enter “1,” and when it is not more
than 99¢, enter “0” or nothing.
*1 First figure:
(1 or 0)
The second figure depends upon whether your tax table is to be programmed as tax table 1,
2, 3 or 4.
Second figure:
(1 to 4)
*2 If the rate is fractional (e.g. 4-3/8%), then the fractional portion (3/8) would be converted to its decimal
equivalent (i.e. .375) and the resulting rate of 4.375 would be entered. Note that the nominal rate (R) is
generally indicated on the tax table.
If you make an incorrect entry before entering the M in programming a tax table, cancel it with the
l key; and if you make an error after entering the M, cancel it with the s key. Then program
again from the beginning.
• Limitations to the entry of minimum breakpoints
The register can support a tax table consisting of no more than 72 breakpoints. (The maximum number of
breakpoints is 36 when the breakpoint difference is $1.00 or more.) If the number of breakpoints exceeds the
register’s table capacity, then the manual entry approach should be used.
Example: Programming the sample tax table shown on the previous page as tax table 1
Key operation example
Print
s 8 @
1 @
6 @
Tax rate
M
100 @
1 @
T
Q
11 @
23 @
39 @
57 @
73 @
89 @
111 @
A
The first
cyclic
portion
M1
(MAX point)
You do not need to enter the trailing zeros of the tax rate (after the decimal point) but you do need
to enter the decimal point for fractions.
30
• If the tax is not provided for every cent, modify the tax table by setting the tax for every cent
in the following manner.
When setting the tax, consider the minimum breakpoint corresponding to unprovided tax to be the same as the
one corresponding to the tax provided on a large amount.
Sample tax table
Example 8%
Modification of the left tax table
Minimum
breakpoint
Minimum
breakpoint
Breakpoint
difference (¢)
Tax
Tax
.00
.01
.02
.03
.04
.06
.09
.10
.11
.12
.14
.17
.01
.11
.26
.47
.68
.00
.01
.02
.03
.04
.05
.06
.07
.08
.09
.10
.11
.12
.13
.14
.15
.16
.17
.01
.11
.26
.47
.68
.89
.89
1.11 M1
1.11
1.11
1
B: Non-cyclic
C: Cyclic-1
10 (0.11-0.01)
15 (0.26-0.11)
21 (0.47-0.26)
21 (0.68-0.47)
21 (0.89-0.68)
0 (0.89-0.89)
22 (1.11-0.89)
0 (1.11-1.11)
0 (1.11-1.11)
15 (1.26-1.11)
21 (1.47-1.26)
21 (1.68-1.47)
21 (1.89-1.68)
0 (1.89-1.89)
22 (2.11-1.89)
0 (2.11-2.11)
0 (2.11-2.11)
T
Q
.89
1.11
1.26
1.47
1.68
1.89
2.11
1.26
1.47
1.68
1.89
D: Cyclic-2
1.89
2.11
2.11
2.11
M2
From the modified tax table above;
Rate = 8(%), T = $0.01 = 1¢, Q = $0.11 = 11¢, M1 = 1.11, M2 = 2.11, M = 100
Quantity for doughnut tax exempt (for Canadian tax system)
This option is available only when the Canadian tax system is selected.
To program zero
Q’ty for doughnut
tax exempt
(max. 2 digits: 1 to 99)
s 19 @
s A
Example: To program the quantity “6”
Key operation example
Print
19
s @
6
s
A
31
AUXILIARY FUNCTION PROGRAMMING
Department Programming
1
Merchandise can be classified into a maximum of 99 departments. Items sold with use of the department keys
can later be printed on a report that shows the quantities sold and sales amounts classified by department. The
data is useful for making purchasing decisions and other store operations. Departments can be assigned to
articles whose prices were set using PLU/subdepartment function.
When using a department key, you must set the parameters to specify the department status, such as positive
or negative department. Prices can be assigned directly to department keys for frequently purchased items,
which enables you to enter the prices by simply pressing the department keys.
Department status
*
To set all zeros
D
ABCDEFGH
Dept. key
@
A
*To program departments 17 through 32, press the department shift key at this point.
For department 33-99:
To set all zeros
ABCDEFGH
Dept. code
d
To program another department, start from the beginning without pressing the A key.
@
A
Item:
A
Selection:
Taxable
Entry:
Tax 4 status
Tax 3 status
Tax 2 status
Tax 1 status
SICS / Normal
Sign
1
0
Non-taxable
Taxable
B
C
D
E
F
1
Non-taxable
Taxable
0
1
Non-taxable
Taxable
0
1
Non-taxable
SICS
0
1
Normal
0
Negative department
Positive department
1
0
G
H
Entry digit limit
0-7
3
Type of unit price entry
Open and preset
Preset only
2
Open only
1
Inhibit department key
0
Tax status (taxable 1 through 4 / non-taxable)
• When any entry of a taxable department is made in a transaction, tax is automatically computed according to
the associated tax table or rate.
SICS (Single Item Cash Sale)
• If an entry of a department programmed for SICS is made first, the sale will be finalized as a cash sale as
soon as the department key is pressed. If the entry is made after entering a department not programmed for
SICS, the sale will not be finalized until the A key is pressed.
Entry digit limit
• Set the number of allowable digits for the maximum entry amount for each department. The limit is effective
for operations in the REG mode and can be overridden in the MGR mode.
32
Example: Programming department 2 as taxable 1, SICS, negative department, entry digit limit - 7 digits, and
allowing open & preset entry. (ABCDEFGH: 00011173)
Key operation example
Print
00011173
@
" A
From left, EGH
Tax status Sign(F)
Preset unit price
*
To program zero
D
Unit price
Dept. key
(max. six digits)
A
*To program departments 17 through 32, press the department shift key at this point.
For department 33-99:
To program zero
Unit price
(max. six digits)
Dept. code
d
s
A
To program another department, start from the beginning without pressing the A key.
Key operation example
Print
1000
!
A
Unit price
Even if a department is not programmed to allow the entry of preset unit prices in functional
programming, the department is automatically changed to allow the entry of preset unit prices by
this programming entry.
PLU (Price Look-Up) and Subdepartment Programming
2
The PLU function allows speedy key entries whereby a price is automatically called up when a code is entered.
The subdepartment is a kind of “open PLU”, which requires you to enter a price after the PLU code is entered. A
maximum of 1200 PLU/subdepartment settings are possible. Each one belongs to a department and acquires
the department’s parameters (tax status, SICS and sign).
The cash register is preprogrammed so all 1200 codes are assigned as PLUs associated with department 1 and
preset unit price “0”.
33
Unit price and associated department assignment
1
*D
To program zero
3 Unit price
*
Associated
Dept. key
*2PLU code
(max. six digits)
A
p
*1: To assign departments 17 through 32, press the department shift key at this point.
When the associated department is department 33-99:
To program zero
3 Unit price
(max. six digits)
Associated
dept. code
(1 to 99)
*
*2PLU code
d
s
p
A
*2: 1 through 1200 (Depending on the EJ memory size setting, up to 200)
*3: For a subdepartment, set the limit amount of unit price entry.
To program the following PLU, start from entering a unit price or an associated department code without
pressing the A key.
To program another PLU, start from the beginning without pressing the A key.
Key operation example
Print
1
125
p
#
A
Unit price
Associated dept.
PLU code
To delete a PLU code, use the following sequence:
PLU code
p v A
To delete the following PLU
To delete another PLU
PLU/subdepartment selection
To program "0"
*2A
*1PLU code
p
s A
To program the following PLU
To program another PLU
*1: 1 through 1200 (Depending on the EJ memory size setting, up to 200)
*2: 0 for subdepartment or 1 for PLU
Key operation example
Print
1
p
s A
0
PLU/subdept.
When you program the last PLU code, the programming sequence will be complete with a press of
the s key.
34
Miscellaneous Key Programming
3
The cash register provides miscellaneous keys such as %, &, -, f, r, R, V, t, C, c and
A. While the cash register is pre-programmed so you can use these keys, you must set a currency
conversion rate to use V key. You can also program these keys for more convenient use. Please refer to the
data below for programming these keys. Factory setting is indicated with parentheses.
Percent rate (0.00%), tax status (non-taxable), sign (minus), item % and subtotal %
entry* (both are allowed), percent rate limitation (100 %)
%, &
Amount (0.00), tax status (non-taxable), sign (minus), item
(both are allowed), entry digit limit (7 digits)
and subtotal
entry*
-
_
_
Not necessary to program
Entry digit limit (9 digits)
f
r, R
V
Currency conversion rate (0.0000), currency conversion rate entry method - open or
preset (both are enabled)
Compulsory entry of amount tender (not compulsory), entry digit limit (8 digits), footer
printing (not printed)
C, c and
A
Entry digit limit (7 digits)
t (Manual tax)
* Item %/Item
:
_
Percent/discount calculation is applied to individual department and
PLU/subdepartment.
* Subtotal %/Subtotal : Percent/discount calculation is applied to subtotals.
_
Rate for
,
% &
and
V
To program zero
*Rate
or
% & A
V
To program another rate
*: Rate
0.00 — 100.00 (% rate)
0.0000 — 9999.9999 (Currency conversion rate)
Key operation example
Print
10
P
25
6068
P
%
V
0
Percent rate
A
Currency
conversion rate
You must use a decimal point when setting fractional rates.
35
Amount for
-
To program zero
Discount amount (max. six digits)
- A
Key operation example
Print
200
-
A
Discount amount
Percent rate limitation for
and
%
&
To program zero
Percentage limit (0.00 -100.00%)
To program for another percent key
or
s 29 @
% & A
• Percent entries that exceed the upper limit may be overridden in the MGR mode.
• 10.00% can be entered as
for fractional entry.
or
10 10P00
. The
key is needed only
P
Key operation example
Print
29
00
s
P
@
%
15
A
Percentage limit
Function parameters for
,
% &
and
-
To program “0” for all items
*ABCDEFGH
or
@ % & A
-
To program for another key
36
*: Item:
A
Selection:
Taxable
Entry:
Tax 4 status
Tax 3 status
Tax 2 status
Tax 1 status
+/- sign
1
0
Non-taxable
Taxable
B
C
D
E
F
1
Non-taxable
Taxable
0
1
Non-taxable
Taxable
0
1
Non-taxable
+ (premium) sign
- (discount) sign
Allow
0
0
1
Item % / Item
0
_
Disallow
1
G
Subtotal % / Subtotal
Allow
0
_
Disallow
1
H
Entry digit limit for discount key
0-7
When programming for percent keys, always enter 0 for H.
Tax status (taxable 1 through 4 / non-taxable)
• When taxable is selected, tax is applied to the amount obtained after premium or discount calculation.
+/- sign
• Programming of the +/- sign assigns the premium or discount function for each key.
Entry digit limit (For discount key only)
• The entry digit limit is in effect for the REG-mode operations but can be overridden in the MGR mode. The
entry digit limit is represented by the number of allowable digit for the maximum entry amount for discount
key.
Key operation example
Print
00011006
@
- A
From left, FGH
Sign(E)
Tax status
Function parameters for
V
To program “0” for all items
*AB
@ V A
Selection:
Allow
*: Item:
A
Entry:
Open rate entry
Preset rate entry
0
1
0
1
Disallow
Allow
B
Disallow
Key operation example
Print
00
@
V A
From left, AB
37
Entry digit limit for
,
r R
and
t
Entry digit limit
or
@ r, R t A
(only for manual entry)
• For
, enter 0 to 9 (digits), and for
r R
(manual tax), enter 0 to 7 (digits).
t
Entry digit limit is in effect for REG-mode operation but can be overridden in the MGR mode. The entry digit
limit is represented by the number of allowable digits for maximum entry or total amount. When “0” is set, the
operation of the corresponding key is prohibited.
Key operation example
Print
4
@
R A
Function parameters for
,
C c
and
(when using as CA key)
or
A
To program “0” for all items
2
*
*1ABC
@ s, C c A
*2:Press s key for CA key setting.
To program for another key
*1:Item:
Selection:
Allow
Entry:
A
Footer printing
1
0
1
Disallow
B
C
Amount tendered entry
Compulsory
Non-compulsory (for the CA or CHK keys) 0
Inhibit (for the CH key)
0
Entry digit limit
0-8
Footer printing
• This programming decides whether or not the machine should print a message at the foot of a receipt when a
specified media key is used. With regard to programming method of footer logo message, refer to “Logo
Amount tendered compulsory
• You may select amount tendered, compulsory or optional, for the
• You may select amount tendered, compulsory or inhibited, for the
Entry digit limit
and
key.
keys.
A
c
C
• For the
and
keys, program upper limit entry amount for the tendered amount. For the
key,
c
C
A
program upper limit entry for total cash amount which can be handled on the register. The entry digit limit is
in effect for REG-mode operation but can be overridden in the MGR mode. The entry digit limit is represented
by the number of allowable digits for the maximum entry or total amount. When “0” is set, the operation of the
corresponding key is prohibited.
Key operation example
Print
018
@
C A
ABC (A:0, B:1, C:8)
38
Text Programming
4
The register allows you to program the texts for clerk names, department item names, PLU/subdepartment item
names, and so on, if necessary. There are two ways for programming text: using character keys on the
keyboard or entering character codes with numeric keys on the keyboard.
Using character keys on the keyboard
You can enter characters according to the small figures printed in the lower right position of the key tops. For
The following are used as control keys for character entry:
Toggles between upper-case and lower-case letters. By default, the upper-case letter is selected.
H
Once the
key is pressed, you are locked in for entering lower-case letters. “_” lights up at the
H
SHIFT position of the display when lower-case letters entry is selected.
Press the key to enter numeric characters. For example to enter “1”, press the
key. If you press the
entry mode.
and
N
N
N
1
key without pressing the
key, the cash register goes to character codes
1
N
Once the
key is pressed, you are locked in for entering numeric characters. “_” lights up at the
N
NUMBER position of the display when numeric characters entry is selected.
Toggles between single-size and double-size characters. By default, the single-size character is
W
B
selected. Once the
key is pressed, you are locked in for entering double size characters. “_” lights
W
up at the DC position of the display when double-size characters entry is selected.
Backs up the cursor, erasing the character to the left.
To program the word “Clerk01” with the letter “C” being double size.
To make the letter “C” double size character
W g
W
To make character size return to normal size
To toggle the characters to lower-case letters
H
h i j k
N 0 1
To enter numbers
Entering character codes with numeric keys on the keyboard
Numerals, letters and symbols are programmable by entering the character code and the
characters entry is selected, that is, “_” lights up at the NUMBER position of the display, press the
release it.) Set the alphanumeric character code table on the next page. By doing this, you can program
characters other than those on the key tops.
key. (If numeric
:
key to
N
• Double-size characters can be made by entering the character code 253.
• All three digits of the character code MUST be entered (even if it starts with zero).
To program the word “SHARP” in double-size characters
253
083
: : : : : :
072
065
082
080
S
H
A
R
P
When you press an appropriate number key (job code number) and press the
key for text entry just after you
P
start programming with the
key, the cash register will be automatically ready for text entry.
s
Listed below is an overview of what you can program and the allowable number of single sized characters for
each text entry.
• Department text
• PLU text (item label)
• Function text
12 characters
12 characters
8 characters
• Logo message
• Clerk name
• Foreign currency symbol 4 characters
6 lines and 24 characters for each line
8 characters
39
Alphanumeric character code table
Code Character Code Character
Code Character
Code Character
Code Character
.
001
002
003
004
005
006
007
008
009
010
011
012
013
014
015
016
017
018
019
020
021
022
023
024
025
026
027
028
029
030
031
032
033
034
035
036
037
038
039
040
041
042
043
044
045
á
â
ê
î
046
047
048
049
050
051
052
053
054
055
056
057
058
059
060
061
062
063
064
065
066
067
068
069
070
071
072
073
074
075
076
077
078
079
080
081
082
083
084
085
086
087
088
089
090
.
/
091
092
093
094
095
096
097
098
099
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
Ä
Ö
Ü
^
_
’
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
177
178
180
181
182
183
184
185
186
187
188
189
190
191
192
→
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
253
I
G
.
0
S
.
1
G
.
.
ì
2
g
í
3
F
T
K
.
ô
ó
û
ú
œ
4
a
b
c
d
e
f
k
.
L
l
5
↓
ç
°
¿
Ù
à
6
7
Z
D
d
C
c
8
u
´´
9
ú
:
g
h
i
o
´´
;
Æ
ø
ó
<
=
>
?
j
Å
P
k
l
¤
é
e
s
c
z
y
¨
@
A
B
C
D
E
F
G
H
I
m
n
o
p
q
r
è
Pt
i
Ñ
ò
.
u
£
n
s
t
¥
°
u
v
w
x
y
z
{
r
´´
U
Ú
´´
O
J
§
.
K
L
Ø
Ó
Á
Í
(space)
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
↑
]
!
”
A
a
E
e
I
|
[
#
$
%
&
’
}
”
ß
¢
!!
ä
ö
i
ü
æ
1
2
3
U
u
(
å
)
N
.
n
.
C
S
C
.
É
ñ
4
+
,
1/2
*(DC)
F
T
-
←
(DC): Double-size character code
40
Department text
*
To keep current setting
D
Character keys
(max.12 digits)
Dept. key
s 1 P
s A
Dept. code
(1 to 99)
d
To program another dept.
*To program departments 17 through 32, press the department shift key.
Key operation example
Print
1
s P
!
s
A
FRUIT
Text
programmed for
dept. 1
(Programming FRUIT for dept.1)
PLU text (item label)
To keep current setting
Character keys
(max.12 digits)
PLU code
s 2 P
p
s A
When the next PLU code immediately
follows the one just entered
To program another PLU
Key operation example
Print
2
s P
1
p
s
A
Text
programmed for
PLU code 1
MELON
(Programming MELON to PLU1)
Function text
To keep the current setting
*Function no.
(max. 2 digits)
Character keys
(max. 8 digits)
s 3 P
@
s A
To program another function text
* Function no.: See “List of function texts” shown on the following page.
41
Key operation example
Print
3
s P
46
@
s
A
CARD
(Programming CARD for gross
charge)
List of function texts
Function
no.
Default
setting
Function
no.
Default
setting
Key or function
Key or function
(–)
%1
%2
NET1
TAX1 ST
GRS TAX1
RFD TAX1
TAX1
Void mode
VOID
1
2
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
%1
%2
Manager void
Subtotal void
No sale
MGR VD
SBTL VD
NO SALE
RA
3
Net sales total
4
Net taxable 1 subtotal
Gross tax 1 total
Tax 1 total of refund entries
Net tax 1 total
RA
5
PO
PO
6
Customer counter
Sales total
Cash
TRANS CT
NET 3
CASH
CHECK
CHARGE
CHARGE–
7
8
Exempt tax 1
TX1 EXPT
TAX2 ST
GRS TAX2
RFD TAX2
TAX2
9
Net taxable 2 subtotal
Gross tax 2 total
Tax 2 total of refund entries
Net tax 2 total
Check
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
Gross charge
Refund charge
Currency conversion1 (Preset) CONV 1
Currency conversion2 (Open) CONV 2
Exempt tax 2
TX2 EXPT
TAX3 ST
GRS TAX3
RFD TAX3
TAX3
Net taxable 3 subtotal
Gross tax 3 total
Tax 3 total of refund entries
Net tax 3 total
Cash in drawer
Cash+check in drawer
Check change
Exempt VAT
CID
CA+CH ID
CHK/CG
VAT EXPT
DEPT TL
DEPT(–)
SUBTOTAL
MDSE ST
TOTAL
Exempt tax 3
TX3 EXPT
TAX4 ST
GRS TAX4
RFD TAX4
TAX4
(+)Dept. total
Net taxable 4 subtotal
Gross tax 4 total
Tax 4 total of refund entries
Net tax 4 total
(–)Dept. total
Subtotal
Merchandise subtotal
Total
Exempt tax 4
TX4 EXPT
GRS MTAX
RFD MTAX
M-TAX
Change
CHANGE
ITEMS
Gross manual tax total
Refund manual tax total
Net manual tax total
Exempt total from GST
PST total
Items
Department report title
PLU report title
Transaction report title
Clerk report title
Hourly report title
Non add symbol
Copy receipt title
EJ report title
DEPT
PLU
TRANS.
CLERK
HOURLY
#
GST EXPT
PST TTL
GST TTL
TTL TAX
NET
28
*
*
*
29
GST total
30
Tax total
31
32
33
34
35
Net
COPY
EJ
EJ END
Sales total including tax total NET2
Refund
REFUND
EJ report end title
Item void
VOID
• The items marked with “ * ” are for Canada only.
• The function no. 53 “Exempt VAT” is only effective for the Canadian tax system (2 GST, VAT
type).
42
Clerk names
To keep current setting
Clerk code
(1-15)
Character keys
(max. 8 digits)
s 5 P
@
s A
To program another clerk
Key operation example
Print
5
s P
1
@
s
A
DAVID
Logo messages
The register can print programmed messages on every receipt. On the standard model, the graphic logo is
printed on the receipt. If you want to print logo messages, please change the logo print format. (See page 51 for
the programming details.) The options are listed below:
To keep the current setting
*Line number
(1-6)
Character keys
(max. 24 digits)
s 4 P
@
s A
To program another line
* “Header 3-line message” type: 1 to 3
“Footer 3-line message” type : 4 to 6
“Header 6-line message” type: 1 to 6
“Header 3-line and footer 3-line message” type: 1 to 6 (1 to 3 as header, 4 to 6 as footer)
Logo print format (6 types)
Text 1st line
Text 2nd line
Text 3rd line
Text 4th line
Text 5th line
Text 6th line
Text 1st line
Text 2nd line
Text 3rd line
Text 1st line
Text 2nd line
Text 3rd line
Graphic logo
Graphic logo
Graphic logo
Text 1st line
Text 2nd line
Text 3rd line
Text 4th line
Text 5th line
Text 6th line
Text 4th line
Text 5th line
Text 6th line
Default setting
Header 3-line message
Footer 3-line
message
Header 6-line
message
Header 3-line
message and
footer 3-line
messages
43
To print the logo message “THANK YOU” using double sized characters and centering on the third line.
Key operation example Print
4
s P
3
S S S
@
THANK
YOU
W
S
W
S S S
s A
A 6-line logo message is preprogrammed when shipped. Please start entering from the first line
when you first program a logo message.
Foreign currency symbol
Foreign currency symbol for
key is printed with a foreign currency exchange amount.
V
To keep the current setting
Character keys
(max. 4 digits)
s 6 P
s A
Key operation example
Print
s 6 P
S S S
207 :
s A
Entry using
character code
Foreign currency
symbol
ADVANCED PROGRAMMING
Register Number and Consecutive Number Programming
1
Register number and consecutive number are printed on every receipt or journal.
When your store has two or more registers, it is practical to set separate register numbers for their identification.
The consecutive number is increased by one each time a receipt or journal is issued.
For consecutive number programming, enter a number (max. 4 digits) that is one less than the desired starting
number.
Register number
To set the register number “0”
Register number (one to six digits)
@
s A
s 1
Key operation example
Print
1
s @
s A
123456
Register number
44
Setting consecutive numbers
To begin the count from 0001
A number (one to four digits) that is one
less than the desired starting number
@
s A
s 2
Key operation example
Print
2
s @
s A
Consecutive
number
1000
Electronic Journal (EJ) Programming
2
The cash register provides the electronic journal (EJ) function. By default, a maximum of 1000 lines can be
stored in memory. If you want to store more journal data, you can expand to a maximum of 2000 lines, although
the maximum number of PLUs is decreased to 200 codes because the memory is shared with PLU settings.
You can also program various options for EJ, such as availability of EJ memory nearly full warning, availability of
printing EJ data during a transaction, data type to be stored in memory, and printing format.
EJ memory type
When this procedure is executed, EJ data is cleared, and PLU data (programming data and sales
data) are reset to the default after all data is cleared even if the same memory type is selected.
*A
s 90 @
A
*A: 0 for EJ 1000 lines and PLU 1200 codes
1 for EJ 2000 lines and PLU 200 codes
Key operation example
Print
90
s @
1
A
45
Function parameters for EJ
To set “00000000”
*ABCDEFGH
s 68 @
s A
* Item:
Selection:
Entry:
A
B
C
Always enter 0.
(Fixed position)
(Fixed position)
Disallow
0
0
0
1
0
1
0
1
0
1
0
1
0
1
2
Always enter 0.
Temporary EJ printing during transaction
Allow*
D
E
F
EJ printing and clearing EJ data when
issuing general Z1 report
No*
Yes
PGM mode operation records type
Details*
Header information only
Details*
REG/MGR/VOID modes operation
records type
Total
G
H
Compressing printing for EJ data
No (normal size)
Yes (small size)*
Continue
Action when EJ memory area is full
Warning (near full warning)*
Lock (with near full warning)
On the default setting, an asterisk is marked.
Temporary EJ printing during transaction
• If selecting “yes”, you can print journal data of a current transaction recorded in EJ memory by pressing the
key during the transaction. To realize this function completely, the cash register is programmed to
R
receipt printing and set Receipt ON/OFF function to OFF.
PGM mode operation records type
• For data of program reading operation, the header information only is printed.
For X/Z reports, the header information only is printed.
(Receipt sample for Header Information only)
Action when EJ memory area is full
• By default, when the memory for EJ becomes nearly full, the cash register shows decimal points at the 8th
and 9th positions of the display (EJ memory nearly full message), and the cash register keeps storing new
data while erasing the oldest data. When “0” is selected, the cash register will not show EJ memory nearly
full message. When “2” is selected, the cash register shows EJ memory nearly full message and when the
memory gets full, the cash register locks the sales/data entry with a display of the memory full message
“
”. You can only issue an EJ report.
Key operation example
Print
68
s @
s A
00100002
46
Various Function Selection Programming 1
3
The cash register provides various detailed functions listed below.
• Function selection for miscellaneous keys
• Print format
• Receipt print format
• Function selection for tax
• Others
For this programming, job code entry style is applied. You can continue programming until you press the
key for the programming described in this section. To continue programming, repeat from a job code entry.
A
To set “00000000”
*1Job code
*2ABCDEFGH
s
@
s A
*1 Enter job code using numeric keys specified in each section below.
*2 Data entry details are listed on each table in each section below. An asterisk is entered for factory setting.
Example: When programming for job code 5 as ABCDEFGH: 00000100.
Key operation example
Print
5
s @
s A
00000100
Function selection for miscellaneous keys
Job code: 5
* Item:
A
Selection:
Allow the PO operation in REG mode*
Disallow it
Entry:
PO in REG mode
0
1
0
1
0
1
0
1
0
1
0
1
B
C
D
E
F
RA in REG mode
Allow the RA operation in REG mode*
Disallow it
Subtotal void in REG mode
Indirect void in REG mode
Direct void in REG mode
Refund key availability
No sale in REG mode
Fractional quantity availability
Allow the REG mode subtotal void*
Disallow it
Allow the REG mode indirect void*
Disallow it
Allow the REG mode direct void*
Disallow it
Allow the REG mode refund entry*
Disallow it
G
H
Allow the no sale operation in REG mode* 0
Disallow it
1
0
1
Allow fractional quantity entry
Disallow it*
47
Print format
Job code: 6
* Item:
A
Selection:
Entry:
Printing style
Use the printer for journal printing
Use the printer for receipt printing*
Total
0
1
0
1
0
1
0
1
0
1
0
0
1
0
1
B
C
D
E
Receipt print format
Detailed*
Time print on all receipts/journals
Date print on all receipts/journals
Allow time printing*
Disallow it
Allow date printing*
Disallow it
Consecutive no. print on all receipts/journals Allow consecutive no. printing*
Disallow it
F
Always enter 0.
(Fixed position)
Disallow zero skip
Allow zero skip*
Disallow zero skip
Allow zero skip*
G
Zero skip for PLU report
H
Zero skip for general, clerk and
hourly reports
Printing style
• Even when receipt printing is selected, the journal rewind motor will be driven in PGM, OP X/Z, X1/Z1 and
X2/Z2 modes so you can wind sales and programming reports.
Receipt print format
Job code: 7
* Item:
Selection:
Entry:
A
B
C
Always enter 0.
(Fixed position)
0
0
0
1
0
1
0
0
0
0
1
Always enter 0.
(Fixed position)
Subtotal print with a press of subtotal key
Disallow subtotal printing*
Allow it
D
Merchandise print with a press of
merchandise subtotal key
Always enter 0.
Disallow merchandise subtotal printing*
Allow it
E
F
(Fixed position)
Always enter 0.
(Fixed position)
G
H
Always enter 0.
(Fixed position)
Number of purchases print
Allow printing of number of purchases*
Disallow it
Function selection for tax
Job code: 15
* Item:
Selection:
Entry:
A to F Always enter 0.
(Fixed position)
0
0
1
0
1
G
Tax delete in REG mode availability
Allow tax delete in REG mode*
Disallow it
H
Manual tax entry in
Allow manual tax entry in REG mode*
Disallow it
REG mode availability
48
Other programming
Job code: 61
* Item:
Selection:
Entry:
A
B
C
Always enter 0.
Always enter 0.
(Fixed position)
(Fixed position)
0
0
Minus dept. and PLU/subdept. availability Disallow to program minus dept. and PLU/subdept. 0
Allow it*
1
D
Fractional treatment
Round off (4 down, 5 up)*
Raising to unit
0
1
Disregarding fractional treatment
2
E
F
Use of
key
Use
Use
key as 00 key*
key as 000 key
0
:
:
:
1
Time format
Date format
Use 12-hour format*
0
Use 24-hour format
1
G
Use month-day-year format*
Use day-month-year format
Use year-month-day format
0
1
2
H
Position of decimal point (from right) (TAB)
0 to 3 (default 2)
Job code: 62
* Item:
Selection:
(Fixed position)
By lock error*
By misoperation
Allow to sound*
Disallow it
Entry:
A
B
Always enter 0.
0
0
1
0
1
0
1
0
1
Error beep activation
C
D
E
F
Key touch sound availability
Buffered keyboard
Yes*
No
Void mode operation availability
Allow void mode operation*
Disallow it
Void mode entry data print in Z2 reports Allow printing of void mode entry data in Z2 reports*
0
1
0
1
0
1
Disallow it
G
H
Void mode entry data print in Z1 reports Allow printing of void mode entry data in Z1 reports*
Disallow it
Addition of hourly sales total data in
void mode
No*
Yes
Job code: 66
* Item:
Selection:
Entry:
A
B
C
Printing a receipt after transaction
Total only
0
1
0
1
0
1
0
0
1
0
1
0
1
0
1
Details*
Amount printing when PLU/subdept.
unit price is zero
Disallow printing*
Allow it
Subtotal printing for conversion of
deficit
Allow printing*
Disallow it
D
E
Always enter 0.
(Fixed position)
Compression printing on journals in
Disallow compression printing (normal size)
PGM, OP X/Z, X1/Z1 and X2/Z2 modes Allow compression printing (small size)*
F
Compression printing on journals in
REG, MGR and VOID modes
Disallow compression printing (normal size)
Allow compression printing (small size)*
Disallow logo message printing on journals*
Allow logo message printing on journals
Printing footer on all receipts*
G
H
Logo message printing on journals
Footer printing
Printing footer with selected function key at the time of finalization
Compression printing
• This programming is valid only when journal printing is selected. This does not affect EJ printing. (For EJ
49
Job code: 70
* Item:
Selection:
Entry:
A
Split pricing counting
Quantity*
Package
0
1
B
Multiplication/split pricing entry availability Allow multiplication entry only*
0
Allow both of multiplication and split pricing
(Fixed position)
1
C
D
E
Always enter 0.
0
Always enter 0.
(Fixed position)
0
Tax printing when GST is VAT
Allow tax printing*
Disallow it
0
1
F
GST exempt printing on X/Z reports
Tax calculation system
Allow printing of GST exempt*
Disallow it
0
1
00
GH
Auto tax*
Canadian tax (tax type number)
01 through 11
Tax calculation system
• For US tax system, select “auto-tax”.
• For Canadian tax, from the table below, specify a tax system suitable for your province (if necessary contact
your local tax office for correct sales tax information) and for your type of retail business. In the cash register,
four kinds of tax can be set and each tax is arranged to match GST or PST as follows:
Tax 1: PST
Tax 3: PST or GST
Tax 2: PST
Tax 4: GST
Tax 4 method
GST
Tax 3 method
PST
Tax 2 and 1 method
PST
Canadian tax
type number
GST
01
02
03
04
05
06
07
08
09
10
11
VAT
VAT
-
-
Tax on tax
Tax on base
Tax on tax
Tax on base
Tax on Tax
Tax on base
Tax on tax
Tax on base
Tax on tax
Tax on base
Tax on tax
VAT
VAT
VAT
-
Tax on tax
VAT
-
Tax on base
Add on Tax
Add on Tax
Add on Tax
Add on Tax
Add on Tax
Add on Tax
VAT
-
Tax on tax
-
Tax on base
VAT
-
VAT
-
Add on Tax
Add on Tax
-
-
-
VAT (Tax on base)
(The most common type for Canada is type number 06.)
• To program a GST, use Tax 4; and to program two GSTs, use Tax 3 and 4. To program a PST,
use Tax 1; to program two PSTs, use Tax 1 and 2; and to program three PSTs, use Tax 1, 2 and
3.
• The entry of a multi-taxable item for PST or GST is prohibited as follows for the Canadian tax
system. When programming for departments, avoid programming the prohibited multi-taxable
status.
In case of; Tax 1: PST, Tax 2: PST,
Tax 3: PST, Tax 4: GST
In case of; Tax 1: PST, Tax 2: PST,
Tax 3: GST, Tax 4: GST
Taxable 1 and 2 item ········· prohibited
Taxable 1 and 3 item ········· prohibited
Taxable 2 and 3 item ········· prohibited
Taxable 1 and 4 item ············· allowed
Taxable 2 and 4 item ············· allowed
Taxable 3 and 4 item ············· allowed
Taxable 1 and 2 item ········· prohibited
Taxable 1 and 3 item ············· allowed
Taxable 2 and 3 item ············· allowed
Taxable 1 and 4 item ············· allowed
Taxable 2 and 4 item ············· allowed
Taxable 3 and 4 item ········· prohibited
50
Various Function Selection Programming 2
4
The cash register provides various options so you can use the register to suit your sales needs.
In this section, you can program the following features (parameters within parentheses indicates default setting):
• Power save mode (entering the power save mode in 30 minutes)
• Logo message print format (graphic logo only)
• Thermal printer density (standard density)
• RS-232C interface
• Language selection (English)
• Training clerk specification (none)- If you specify a clerk code who is trained for use on this cash register, the
cash register will go into training mode when the clerk code is registered for sales entries. The sales
operations done by the trained clerk does not affect sales total. For details, refer to TRAINING MODE section.
Power save mode
*ABCD
s 10 @
s A
* Item:
A
Selection:
Yes (default)
No
Entry:
Entering power save mode
0
when time is displayed
1
B-D
Time(min.) to entering power save mode
since no operation is made
001-254 or 999
(Default 030)
When 999 is set for B to D, entering into power save mode is inhibited.
Key operation example
Print
10
s @
s A
0060
Logo message print format
You can select the number of lines for your logo message, and the position to print it on receipt or journal.
To set “0”
*A
s 11 @
s A
*A: Logo message type
0: Header 3-line message without graphic logo
1: Graphic logo only
2: Footer 3-line message with graphic logo
3: Header 6-line message
4: Header 3-line message with graphic logo
5: Header 3-line message and footer 3-line message
Key operation example
Print
11
s @
s A
0
51
RS-232C interface
(1) RS-232C terminal number
To set “0”
Terminal number
(max. 6 digits)
s 30 @
s A
(2) RS-232C transmission form
To set “0”
*A
s 31 @
s A
Entry:
* Item:
A
Selection:
Transmission line form
Half duplex system
Full duplex system*
1
0
(3) RS-232C baud rate
*AB
s 32 @
s A
* Item:
Selection:
Entry:
A
B
Always enter 0.
Baud rate (bps)
0
3
4
5
6
2400
4800
9600*
19200
(4) RS-232C start code and end code
To set “000000”
*ABCDEF
s 33 @
s A
*A-C: Start code 000-127
D-F: End code 000-127
(5) RS-232C time out setting
Time out (1 to 255 sec.)
s 35 @
s A
Key operation example
Print
30
s @
s A
2
52
Thermal printer density
To set “0”
*Printer density
(00-99)
s 50 @
s A
* By default, 50 is set. To make the print darker, set a larger number, and to make the print lighter, set a smaller
number.
Key operation example
Print
50
s @
s A
00
Language selection
To set “0”
*Language
(0, 2 or 3)
s 88 @
3: Spanish
A
*Language: 0: English
2: French
Key operation example
Print
88
s @
2
A
When you change the language, the text such as department/PLU, clerk name, logo message and
function text, which you programmed, will be reset to the default settings.
Training clerk specification for training mode
To cancel
Clerk code
(1 to 15)
s 86 @
s A
Key operation example
Print
86
s @
s A
15
53
AUTO key programming — Automatic sequencing key —
If you program frequently performed transactions or report sequences for the
key, you can call those
a
transactions and/or reports simply by pressing the
key in key operations.
a
Delete
Transaction
a
a A
max. 25 times
Programming for a; entering a PLU 2 item (programmed unit price: 1.50) and a dept. 6 item (unit price: 1.00)
Key operation example
Print
a
+
a
AUTO
setting
2
100
p
A
When the
key has been programmed to execute a report job function etc., the mode switch
a
must be in the appropriate position (X1/Z1 or X2/Z2).
Reading Stored Programs
5
The machine allows you to read every program stored in the PGM mode.
Key sequence for reading stored program
Report name
Key sequence
Programming report 1
A
Programming report 2
2
1
3
A
Auto key programming report
Printer density programming report
PLU programming report
A
A
Start PLU code
@
End PLU code
p
To stop reading PLU programming report, turn the mode switch to the MGR position.
54
Sample printouts
1 Programming report 1
Mode
Dept. code
Dept. text
Dept. unit price w/sign
Dept. function
Minus department
Logo Message
Tax status
Function selection for
miscellaneous keys (A-H)
Function no.& its text
Tax status
Print format (A-H)
Receipt print format(A-H)
Power save mode(A-D)
Logo message print format
Function selection for tax (A-H)
Doughnut tax exempt
Function parametrs (F-H)
Discount amt. w/sign
Function parametrs (F-H)
Percent rate with sign
RS-232C terminal no.
RS-232C transmission form (A)
Percent limit
RS-232C baud rate(AB)
RS-232C Start-End code
RS-232C timeout
Entry digit limit
Entry digit limit
Thermal printer density
Tax table
Function parameters (A-C)
Function parameters
Tax rate
Min. taxable amount
Foreign currency
symbol/Rate
Clerk code/name
55
2 Programming report 2
4 Printer density programming report
Entered Value
Printer density
Job code
A to H from the left
* Job code #63, 64, 65, 67,
69, 71, 72, 76, 77, 85, 87
and 95 are fixed settings,
for which you cannot
Printing density
example
change the settings.
5 PLU programming report
Training clerk specification
Range
Language selection
EJ memory type
PLU code
PLU text
Mode parameter
Unit price
3 Auto key programming report
Associated
dept. code
TRAINING MODE
The training mode is used when the operator or the manager practices register operations.
When a clerk in training is selected, the machine automatically enters the training mode. To specify a clerk to be
trained, refer to “Training clerk specification for training mode” in “ADVANCED PROGRAMMING” in page 53.
The training operation is valid only in REG, MGR and VOID mode.
The corresponding clerk memory is only updated in the training mode.
Key operation example
Print
A clerk set in training
15 L
1000 >
3 @
#
A
56
READING (X) AND RESETTING (Z)
OF SALES TOTALS
• Use the reading function (X) when you need to take a reading of sales information entered since the last reset.
You can take this reading any number of times. It does not affect the register’s memory.
• Use the resetting function (Z) when you need to clear the register’s memory. Resetting prints all sales
information and clears the entire memory except for the GT1 through GT3, Training GT, reset count, and
consecutive number.
Summary of Reading (X) and Resetting (Z) Reports
1
X1 and Z1 reports: Daily sales reports
X2 and Z2 reports: Periodic (monthly) consolidation reports
When you take a X or Z report, turn the mode switch to the appropriate position referring to the column of “Mode
switch position” shown on the table below, and use the following corresponding key sequence.
Mode switch position
Item
Key operation
OPX/Z X1/Z1 X2/Z2
Dept. code
: Department total amount
d
Flash report:
(Only display)
To clear the
For dept. 1 to 16;
Dept. key ( !to <)
For dept. 17 to 32; D
Dept. key ( !to <)
display, press the
X
--
--
key or turn the
mode switch to
l
key: Amount of cash in drawer
@
another position.
Akey: Sales total
Reading: A
Full sales report
-- X1, Z1 X2, Z2
Resetting: P
Resetting: P
A
L
Individual clerk
report
Reading: L
(The report of the current clerk)
X, Z
--
--
Full clerk report
PLU sales report
Reading: L
L
Resetting: P
-- X1, Z1 --
All PLUs
Start
PLU code
End
PLU code
Reading:
@
p
-- X1, Z1 --
Resetting:
All PLUs
Start
PLU code
End
PLU code
@
P p
s
Hourly report
Reading: s
Resetting: P
-- X1, Z1 --
• When both sales quantities and sales amounts are zero, printing is skipped. If you do not want to
Programming 1”.)
• “X” represents read symbol and “Z” represents reset symbol in the reports.
• To stop reading and resetting the PLU sales report, turn the mode switch to the MGR position.
The data will not be erased when you reset.
57
Daily Sales Totals
Full sales report
2
• Sample report
Mode title*1
Reset counter
Net grand total(GT2-GT3)
*2
Manual tax total
*3
Grand total of plus
registration
Grand total of
minus registration
Tax total
Net total without tax
Net total with tax
Grand total of training
mode registration
Item counter and total
Dept. code
Sales q'ty
Item percent 1
counter and total
Sales amount
REG-mode void counter
and total
Subtotal void counter and
total
Manager item void counter
and total
“+” dept. counter
Void-mode transaction
counter and total
and total
Refund counter and total
“-” dept. counter
Received on account
counter and total
and total
Paid out counter and total
No-sales counter
Subtotal counter
and total
Subtotal percent 1
counter and total
Customer counter
Sales total
Cash counter and total
Next sales total
Check sales counter and total
Charge sales counter and total
Charge refund counter and total
Taxable 1 total
Gross tax 1 total
Refund tax 1 total
Net tax 1 total
Foreign currency total (preset)
Foreign currency total (open)
Cash in drawer
Cash + check in drawer
Change total for check tendering
*1: When you take X1 report, “X1” is printed.
*2: Printed in the Z1 report only.
*3: When the Canadian tax system is selected, the following is printed here.
Exempt total from GST
PST total
GST total
58
Clerk reports
PLU sales report
• Sample report
Individual clerk report
• Sample report
Mode title*
Report title
Range
Mode title*
Report title
PLU code
Item label
Clerk code
Sales q'ty and total
Clerk name
Customer counter
Full clerk report
The printout occurs in the same format as in the
sample report of individual clerk, but all clerk’s sales
data are printed in the order of clerk code number
(from #1 to #15).
Range sum
Hourly report
• Sample report
*: When you take Z1 report, “Z1” is printed.
Mode title*
Report title
Customer counter
Sales total
*: When you take Z1 report, “Z1” is printed.
Periodic Consolidation
3
Full sales report
• Sample report
Mode title*1
The subsequent printouts are the same in format
as in the X1/Z1 full sales report.
Reset counter of daily total
Reset counter of periodic
*2
*1: When you take X2 report, “X2” is printed.
*2: Printed in the Z2 report only
Grand total
59
EJ REPORT READING AND RESETTING
The cash register provides electronic journal (EJ) function. This function is intended to record the journal data in
a memory instead of journal paper, and print the data as an EJ report. The register records the journal data in
REG, PGM, VOID, X1/Z2 and Z2/Z2 modes. By default, a maximum of 1000 lines are stored in the memory,
and you can expand it to 2000 lines. For details of EJ programming, please refer to “Electronic Journal
Printing journal data on the way of a transaction
You can print journal data of a current transaction recorded in EJ memory by pressing the
transaction.
key during the
R
This function is valid when the printing style is set to receipt type on the programming, and also the
receipt ON/OFF function is set to OFF.
• Sample print
EJ report title
EJ report end title
Reading and resetting the electronic journal data (Issuing EJ report)
You can read the journal data stored in the EJ memory in the journal format by executing the following
procedure in the X1/Z1 or OP X/Z mode.
• Sample EJ report
To read all of the data:
7: @ A
To reset all of the data:
7: P @ A
To read the last 10 records:
Header
information
print
710 @ A
• On the EJ memory, a maximum of 1000 (or 2000, if
programmed) lines of data can be stored. When executing all
data reading, all of the data stored in the EJ memory will be
printed. To save paper, compression print is available.
• To stop reading or resetting the data, turn the mode switch to
“MGR” position. The data will not be erased when resetting.
60
OVERRIDE ENTRIES
Programmed limit for functions (such as for maximum amounts) can be overridden by making an entry in the
MGR mode.
1. Turn the mode switch to the MGR position.
REG
OPX/Z
OFF
MGR
X1/Z1
X2/Z2
2. Make an override entry.
VOID
PGM
On this example, the register has been programmed not to allow
discounts entries over $1.00.
Key operation example
Print
REG-mode
entries
1500
250
#
-
l
...Error
Turn the mode switch
to the MGR position.
250
-
Return the mode switch
to the REG position.
A
CORRECTION AFTER FINALIZING A
TRANSACTION (Void mode)
When you need to void incorrect entries that clerks cannot correct (incorrect entries found after finalizing a
transaction or cannot be corrected by direct or indirect void), follow this procedure:
1. Turn the mode switch to the
position using the manager key (MA), to enter
VOID
REG
OPX/Z
OFF
MGR
X1/Z1
X2/Z2
into the void mode.
2. Repeat the entries that are recorded on an incorrect receipt. (All data for the
incorrect receipt are removed from register memory; the voided amounts are
added to the void-mode transaction totalizer.)
VOID
PGM
Incorrect receipt
Cancellation receipt
61
OPERATOR MAINTENANCE
In case of Power Failure
1
When power is lost, the machine retains its memory contents and all information on sales entries.
• When power failure is encountered in register idle state or during an entry, the
machine returns to normal operation after power recovery.
• When power failure is encountered during a printing cycle, the register prints
“========” and then carries out the correct printing procedure after power
recovery. (See the sample print.)
In Case of Printer Error
2
If the printer runs out of paper, the printer will stall, and “PPPPPPPPPP” will appear on the display. Key entries
will not be accepted. Refer to section 5 in this chapter, install a new roll, then press the
print the power failure symbol and resume printing.
key. The printer will
l
If the print head comes up, the printer stalls, “H” will appear on the extreme left of the display. Key entries will
not be accepted. Bring the print head back to the correct position, then press the
the power failure symbol and resume printing.
key. The printer will print
l
Cautions in Handling the Printer and Recording Paper
Cautions in handling the printer
3
• Avoid dusty and humid environments, direct sunlight and iron powder (a
permanent magnet and electromagnet are used in this machine.)
• Use the print head release lever only when necessary.
• Never pull the paper when it is in contact with the print head. First release the
head with the print head release lever, and then remove the paper.
• Never touch the surface of the print head.
• Never touch around the print head and the motor during printing or before
they have had sufficient time to cool.
Cautions in handling the recording paper (thermal paper)
• Use only the paper specified by SHARP.
• Do not unpack the thermal paper until you are ready to use it.
• Avoid heat. The paper will color at around 70°C.
• Avoid dusty and humid storage places. Avoid direct sunlight.
• The printed text on the paper can discolor under conditions of high humidity and temperature, exposure to the
direct sunlight, contact with glue, thinner or a freshly copied blueprint, and heat caused by friction from
scratching or other such means.
• Be very careful when handling the thermal paper. If you want to keep a permanent record, copy the printed text
with a photocopier.
62
Replacing the Batteries
4
This cash register displays a low battery symbol ( ) when the batteries are low, and displays a no battery
symbol ( ) when batteries are extremely low or batteries are not installed.
When the low battery symbol is displayed, replace the batteries with new ones as soon as possible. The
existing batteries will be dead in about two days.
When the no battery symbol is displayed, replace the batteries immediately. Otherwise, if the AC power cord is
disconnected or a power failure occurs, all the programmed settings will be reset to the default settings and any
data stored in memory will be cleared.
Be sure to observe precautions shown on page 1 when handling batteries.
To replace the batteries:
1. Make sure that the cash register is plugged in.
2. Turn the mode switch to the REG position.
3. Remove the printer cover.
4. Open the battery compartment cover next to the paper roll cradle and
remove the old batteries.
5. Install three new “AA” batteries in the battery compartment. Be sure the
positive and negative poles of each battery are facing in the proper direction.
When they are installed correctly, the “ ” or “ ” symbol will disappear.
6. Close the battery compartment cover.
7. Replace the printer cover.
Replacing the Paper Roll
5
Be sure to use paper rolls specified by SHARP.
The use of any other paper rolls other than those specified could cause paper jamming, resulting in register
malfunction.
Paper specification
Paper width: 57.5 ± 0.5 mm
Max. outside diameter: 80 mm
Quality: Thermal paper
• Be sure to set paper roll(s) prior to using your machine, otherwise it may cause a malfunction.
Install the paper roll in the printer. Be careful to set the roll and cut the paper end correctly.
If the top end of the paper roll is fixed with paste or tape, the paper may lose its color development ability in the
pasted or taped area due to the deterioration of the heat-sensitive color development component of the paper
surface. This may result in nothing appearing at this location when printing. Therefore, when setting a new paper
roll in the machine, be sure to cut off approximately one revolution (approx. 25 cm long).
(How to set the paper roll)
(How to cut the paper end)
To the printer
To the printer
Correct
Incorrect
Correct
Incorrect
63
Removing the paper roll
When a red dye appears on the paper roll, it is time to replace it. Replace the paper roll with new one. If you
plan on not using the register for an extended period of time, remove the paper roll, and store it in an appropriate
place.
Caution: The paper cutter is mounted on the cover. Be careful not to cut yourself.
When the take-up spool is not used:
1. Remove the printer cover.
2. Cut the paper behind the printer and near the paper roll.
3. Press the
key until the paper remaining in the printer comes out
F
completely.
4. Remove the paper roll from the paper roll cradle.
Do not pull the paper through the printer.
When the take-up spool is used:
1. Remove the printer cover.
2. Press the
key to advance the journal paper until its printed part is out of
F
the way.
3. Cut the paper and remove the take-up spool.
4. Cut the paper behind the printer and near the paper roll.
5. Press the
key until the paper remaining in the printer comes out
F
completely.
6. Remove the paper roll from the paper roll cradle.
Do not pull the paper through the printer.
7. Remove the outer side of the take-up spool as shown
on the left.
8. Remove the printed journal roll from the take-up spool.
64
Installing the paper roll
Caution: The paper cutter is mounted on the cover. Be careful not to cut yourself.
1. Turn the mode switch to the REG position with the AC cord connected.
2. Remove the printer cover.
3. Check that the print head release lever is in the printing position.
4. Set the paper correctly in the paper roll cradle.
5. Insert the end of the paper into the printer until it is caught by the printer
auto-feed and comes out of the printer at the top.
If the printer does not catch the paper, feed the paper while pressing the
key.
F
6. When not using the take-up spool (using as receipt paper) :
• Cut off the excess paper using the edge of the inner cover, and replace the
printer cover. Press the
out of the printer cover.
key to make sure that the paper end comes
F
If the paper end does not come out, open the printer cover,
and pass the paper end between the paper cutter and the
paper guide of the printer, and replace the cover.
When using the take-up spool (using as journal paper):
• Insert the end of the paper into the slit in the spool. (Press the
key to
F
feed more paper if required.)
• Wind the paper two or three turns around the spool shaft.
• Set the spool on the bearing, and press the
slack in the paper.
key to take up excess
F
• Replace the printer cover.
You can wind the roll paper in OP X/Z, X1/X2, and X2/Z2 modes
even if you programmed so that the printer is used for issuance of
receipts. This may be convenient to wind reports. In this case,
set the roll paper to the take-up spool.
When you want to manually install a new roll of paper while the machine is turned off, follow the
steps shown below:
1. Pull the print head release lever toward you (to the head-up position). (Refer to the drawing on page 62.)
2. Correctly place the new paper roll into the paper roll cradle.
3. Insert the paper end into the printer until it comes out of the printer.
4. Return the print head release lever to its original position.
Removing a Paper Jam
6
Caution: The paper cutter is mounted on the cover. Be careful not to cut yourself. Never touch the print
head immediately after printing, because the head may still be hot.
1. Remove the printer cover.
2. Pull the print head release lever toward you (to the head-up position). (Refer to the drawing on page 62.)
3. Remove the paper jam. Check for and remove any shreds of paper that may remain in the printer.
4. Return the print head release lever to its original position.
5. Reset the paper roll correctly by following the steps in “Installing the paper roll”.
65
Cleaning the Print Head
7
When the printed text is getting dark or faint, paper dust may be stuck to the print head. Clean the print head as
follows:
Caution:
• Never touch the print head with a tool or anything hard as it may damage
the head.
• The paper cutter is mounted on the cover. Be careful not to cut yourself.
1. Turn the mode switch to the OFF position.
2. Remove the printer cover.
3. Remove the inner cover that protects the printer. (Press the lever located
both sides and lift the cover up.)
4. Pull the print head release lever toward you (to the head-up position). (Refer
5. Clean the print head with a cotton swab or soft rag moistened with ethyl
Roller
alcohol or isopropyl alcohol.
Print head
6. Return the print head release lever to its original position immediately after
cleaning.
7. Replace the inner cover. (Insert the side tabs of the cover into their slots and
press the cover in the printer until it is properly seated.)
8. Reset the paper roll correctly by following the steps in “Installing the paper
roll”.
Removing the Drawer
8
The drawer in the register is detachable. After closing your business for the
Coin case
day, remove the drawer. To detach the drawer, pull it forward fully, and
remove it by lifting it up. The 5-denomination coin case is detachable.
Opening the Drawer by Hand
9
The drawer automatically opens. However, when a power failure occurs or the
machine becomes out of order, slide the lever located on the bottom of the
machine in the direction of the arrow. (See the figure at the left.)
The drawer will not open if it is locked with the drawer lock key.
Lever
66
Before Calling for Service
10
The malfunctions shown in the left-hand column below, labelled “Fault,” do not necessarily indicate functional
faults of the machine. It is therefore advisable to refer to “Checking” shown in the right-hand column before
calling for service.
Fault
Checking
(1) The display shows symbols that do not make sense.
• Has the machine been initialized properly as shown
“GETTING STARTED”?
(Note that initialization clears all the data and programmed
settings stored in memory.)
(2) The display won’t be illuminated even when
the mode switch is turned to any other
position than “OFF”.
• Is power supplied to the electrical outlet?
• Is the power cord plug out or loosely connected to the
electrical outlet?
(3) The display is illuminated, but the whole machine
refuses registrations.
• Is a clerk code assigned to the register?
• Is the mode switch set properly at the “REG” position?
(4) No receipt is issued.
• Is the paper roll properly installed?
• Is there a paper jam?
• Is the receipt function in the “OFF” status?
• Is the print head release lever at the printing position?
(5) No journal paper is taken up.
• Is the take-up spool installed on the bearing properly?
• Is there a paper jam?
• Is the journal printing selected in the printing style
programming? (If the receipt printing is selected, the paper
is not wound around the take-up spool.)
(6) Printing is unusual.
• Is the print head release lever at the printing position?
• Is the paper roll properly installed?
Error code table
When the following error codes are displayed, press the
below.
key and take a proper action according to the table
Action
l
Error
Error status
code
E01
E02
E03
E07
E11
Registration error
Make a correct key entry.
Make a correct key entry.
Enter a correct code
Misoperation error
Undefined code is entered.
Memory is full (in the
key programming).
Program the
key within 25 steps.
a
Compulsory depression of the
direct finalization
a
s
key for
Press the
key and continue the operation.
s
E12
E32
E34
E35
E36
E37
E67
Compulsory tendering
No entry of a clerk code
Overflow limitation error
Make a tendering operation.
Make a clerk code entry.
Make a registration within a limit of entry.
Make a preset price entry.
The open price entry is inhibited.
The preset price entry is inhibited.
The direct finalization is inhibited.
Subtotal void is not allowed.
Make an open price entry.
Make a tendering operation.
Finalize the transaction, and correct the wrong entries in the
void mode.
67
SPECIFICATIONS
Model:
XE-A201
Dimensions:
Weight:
13.0 (W) x 16.9 (D) x 11.0 (H) in. (330 (W) x 428 (D) x 280 (H) mm)
16.8 Ib (7.6 kg)
Power source:
Power consumption:
120V AC ± 10%, 60 Hz
Stand-by 7W
Operating 34.5W (max.)
32 °F to 104 °F (0 °C to 40 °C)
LSI (CPU) etc.
Working temperature:
Electronics:
Display:
Operator display:
Customer display:
Printer:
7-segment display (10 positions)
7-segment display (7 positions)
Type:
One-station thermal printer
Printing speed:
Printing capacity:
Other functions:
Approx. 10 lines/second
24 digits each for receipt and journal paper
• Graphic logo printing function
• Logo message function
• Receipt (ON-OFF) function, compression printing function
Width: 2.25 ± 0.02 in (57.5 ± 0.5 mm)
Max. diam.: 3.15 in (80 mm)
Paper roll:
Quality: High quality (0.06 to 0.08 mm thickness)
4 slots for bill and 5 for coin denominations
Cash drawer:
Accessories:
Manager key
2
Operator key
2
Drawer lock key
2
Paper roll
1
Take-up spool
1
RS-232C cable (QCNWG3190BHZZ)
Fixing tape for peripherals
Quick Start Guide
Instruction manual
1
1 set
1 copy
1 copy
* Specifications and appearance subject to change without notice for improvement.
Use these labels with the department keys. Write department names on the labels and attach them to the
department keys by first removing the transparent key covers. (Please make a copy of this page.)
Example:
17
Candy
Danish
1
E
18
22
26
30
20
24
28
32
2
1
6
5
10
14
13
4
3
8
7
12
11
16
15
D
I
N
S
B
G
L
Q
17
21
25
29
19
23
27
31
9
E
J
O
T
C
H
M
R
68
INDICE
INTRODUCCION............................................................................................................................................1
IMPORTANTE................................................................................................................................................1
INDICE ..........................................................................................................................................................2
PARTES Y SUS FUNCIONES.......................................................................................................................3
1 Ejemplo de registro básico de ventas ...................................................................................................5
2 Aviso de error........................................................................................................................................6
3 Registros de artículos ...........................................................................................................................6
Registros de un solo artículo..........................................................................................................6
Registros de multiplicación.............................................................................................................7
Registros de venta en metálico de un solo artículo (SICS)............................................................8
4 Visualización de los subtotales .............................................................................................................8
5 Finalización de una transacción............................................................................................................8
6 Cálculo de los impuestos ......................................................................................................................9
1 Registros auxiliares...............................................................................................................................9
2 Tratos de pagos auxiliares ..................................................................................................................10
CORRECCION.............................................................................................................................................11
PROGRAMACION DE LAS FUNCIONES BASICAS (Para el inicio rápido)............................................12
1 Programación de la fecha y de la hora................................................................................................12
2 Programación de los impuestos para la función de cálculo automático de los impuestos..................12
1 Programación de secciones................................................................................................................14
2 Programación de PLU (codificación de precios) y subsección ...........................................................15
3 Programación de teclas misceláneas..................................................................................................16
4 Programación de texto ........................................................................................................................18
PROGRAMACION AVANZADA..................................................................................................................22
1 Programación de número de caja registradora y de número consecutivo..........................................22
2 Programación del registro diario electrónico (EJ) ...............................................................................22
3 Programación 1 de selección de diversas funciones ..........................................................................23
4 Programación 2 de selección de diversas funciones ..........................................................................26
5 Lectura de programas almacenados...................................................................................................29
MODO DE INSTRUCCION ..........................................................................................................................29
LECTURA (X) Y REPOSICION (Z) DE LOS TOTALES DE VENTAS .......................................................29
LECTURA Y REPOSICION DE INFORMES EJ..........................................................................................30
1 En caso de corte de la alimentación ...................................................................................................31
2 En el caso de error de impresora........................................................................................................32
3 Precauciones al manejar la impresora................................................................................................32
4 Reemplazo de las pilas .......................................................................................................................32
5 Reemplazo del rollo de papel..............................................................................................................33
6 Extracción del papel atascado ............................................................................................................34
7 Limpieza del cabezal de impresión .....................................................................................................34
8 Extracción del cajón ............................................................................................................................35
9 Abertura manual del cajón ..................................................................................................................35
10 Antes de solicitar el servicio de un técnico..........................................................................................35
2
PARTES Y SUS FUNCIONES
Selector de modo y llaves de modo
1
El selector de modo funciona insertando una de las dos llaves de modo suministradas: la llave del administrador
(MA) y la del operador (OP). Estas llaves pueden insertarse o sacarse sólo cuando el selector esté en la
posición “REG” u “OFF”.
El selector de modo tiene estos ajustes:
OFF:
Este modo bloquea todas las operaciones de la caja. (La alimentación de CA está desconectada.)
No hay cambios en los datos registrados.
OP X/Z: Para sacar informes X o Z de dependiente individual, y para sacar informes rápidos. Puede usarse
para alternar el estado “ON” u “OFF” de emisión de recibos pulsando la tecla
Para registrar ventas.
Para programar diversos artículos.
Para establecer la caja registradora en el modo de cancelación. Este modo permite la corrección
después de haber finalizado una transacción.
.
R
REG:
PGM:
VOID:
MGR:
Para los registros del administrador. El administrador puede usar este modo para un registro de
anulación.
X1/Z1: Para sacar el informe X/Z de varios totales diarios.
X2/Z2: Para sacar el informe X/Z de consolidación periódica (semanal o mensual).
Visualizadores
2
Importe:
Aparece en las ocho posiciones (máx.) de la derecha. Cuando el importe es negativo, aparece el
signo de menos “-” delante del importe.
Número de repeticiones para registros repetitivos:
Se visualiza el número de repeticiones, empezando por “2” y se incrementa con cada repetición.
..... ...
)
Cuando haya registrado diez veces, la visualización mostrará “0”. (2 → 3
Estado de la función de recibo:
9 → 0 → 1 → 2
Aparece el indicador “–” en la posición RCPT OFF cuando se pone la función de recibo en el
estado OFF.
Hora:
Aparece en las seis posiciones de la derecha (hora-minutos-“ ” u hora-minutos-“ ”) en el modo
OP X/Z, REG, o MGR. En los modos REG o MGR, pulse la tecla para visualizar la hora.
s
Símbolos del estado de la máquina
:
:
:
Aparece durante la programación.
Aparece cuando se detecta un error.
Aparece cuando se visualiza el subtotal o cuando se entrega un importe menor que el importe de las
ventas.
:
:
:
Aparece cuando se pulsa la tecla
para calcular un subtotal en moneda extranjera.
V
Aparece cuando se finaliza una transacción pulsando la tecla
Aparece cuando se visualiza el importe del cambio.
,
A C c
o
.
: Puede aparecer en las tres posiciones de la izquierda al efectuar una entrada de teclas cuando la
memoria del registro diario electrónico (EJ) está llena. (Dependiendo de la programación.)
:
:
:
Aparece cuando la tensión de las pilas instaladas está por debajo del nivel necesario.
Aparece cuando las pilas no están instaladas, o cuando las pilas instaladas están gastadas.
Es posible que aparezca justo debajo de las posiciones octava y novena al realizar la finalización de una
transacción cuando la memoria del registro diario electrónico (EJ) está casi llena.
También aparece justo debajo de la décima posición cuando está activada el modo de ahorro de
energía.
:
Aparece cuando la palanca de liberación del cabezal impresión está en la posición levantada.
: Aparece cuando se ha terminado el papel.
3
PARA EMPEZAR
Siga el procedimiento mostrado a continuación. Las pilas no están instaladas y la alimentación está
desconectada.
1. Inicialice la caja registradora
Para que la caja registradora pueda funcionar correctamente, deberá inicializarla antes de ponerla en
funcionamiento por primera vez. Siga el procedimiento siguiente.
1. Inserte la llave de administrador (MA) en el selector de modo y gírelo a la posición REG.
2. Enchufe la clavija a la toma de corriente de CA. El zumbador sonará tres veces.
IMPORTANTE: Esta operación debe efectuarse antes de haber instalado las pilas.
3. La caja registradora habrá quedado ahora inicializada.
El visualizador de la caja registradora mostrará “0.00” con “ ”.
2. Instale las pilas
Las tres pilas nuevas del tamaño “AA” se deben colocar en la caja registradora para evitar que los datos y
ajustes de programación se borren de la memoria, cuando se desconecte accidentalmente el cable de
alimentación de CA, o en caso de un corte de corriente.
Instale las tres pilas nuevas del tamaño “AA” de acuerdo con el siguiente procedimiento con el cable de CA
enchufado y ponga el selector de modo en la posición REG. Asegúrese de observar las precauciones indicadas
en la página 1 sobre la manipulación de las pilas.
1. Empuje la cubierta de la impresora hacia delante y sepárela.
Tenga mucho cuidado con el cortador de papel, porque podría cortarse.
2. Abra la cubierta del compartimiento de las pilas que se encuentra al lado del soporte del rollo de papel.
3. Inserte tres pilas nuevas del tamaño “AA”.
Cuando las pilas están correctamente instaladas, desaparecerá “ ” del visualizador.
4. Cierre la cubierta del compartimiento de las pilas.
3. Instale un rollo de papel
1. Corte el papel aproximadamente una vuelta del rollo. Asegúrese de que el extremo del papel se corta.
2. Ponga el papel en el soporte del rollo de papel.
3. Inserte el extremo del papel en la impresora hasta que entre en el dispositivo de alimentación automática de
la impresora y salga de la impresora por la parte superior. Si la impresora no engancha el papel, haga
avanzar el papel mientras pulsa la tecla
4. Cuando no emplee el carrete de toma (cuando se usa como papel de recibos):
.
F
• Corte el papel sobrante empleando el borde de la cubierta interior, y vuelva a colocar la cubierta de la
impresora. Pulse la tecla
Cuando emplee el carrete de toma (empleo como papel de registro diario):
para asegurarse de que el papel sale por la cubierta de la impresora.
F
• Inserte el extremo del papel en la ranura del carrete. (Pulse la tecla
es necesario.)
para hacer avanzar más el papel si
F
• Coloque el carrete en el rodamiento, y pulse la tecla
• Vuelva a colocar la cubierta de la impresora.
para tensar el papel.
F
4. Programe la fecha, la hora y los impuestos
La caja registradora le ofrece los idiomas inglés, francés y español para el texto. El idioma
preajustado es el inglés. Si desea cambiar el idioma, deberá cambiarlo antes de realizar la
programación. Consulte el apartado de “Selección del idioma” para cambiar el idioma.
Antes de poder seguir con el registro de las ventas, deberá programar:
• la fecha
• la hora
• los impuestos
Consulte la sección de PROGRAMACION DE LAS FUNCIONES BASICAS para encontrar más detalles (página 12).
5. Programe otros elementos necesarios
Aunque la caja registradora viene ya programada para poderla utilizar con la mínima configuración, la máquina
le ofrece las funciones opcionales. Antes de comenzar la programación, lea la sección de operaciones de
ventas para entender las funciones opcionales.
4
PARA EL OPERADOR
REGISTRO BASICO DE VENTAS
Ejemplo de registro básico de ventas
1
A continuación se muestra un ejemplo de registro básico de ventas de artículos de sección en metálico. Para
los detalles de la operación, consulte cada sección respectiva.
Ajuste del selector de modo
REG
OPX/Z
OFF
MGR
X1/Z1
X2/Z2
1. Gire el selector de modo a la posición REG.
Asignación de dependientes
VOID
PGM
2. Introduzca su código de dependiente. (Por ejemplo, si el código de dependiente es
el 1. Pulse las teclas 1 y L en este mismo orden.)
Registros de artículos
3. Introduzca el precio para el primer artículo de sección. (Por ejemplo, para 15,00, introduzca 15:, y
pulse la tecla de la sección correspondiente.)
Para las secciones 17 a la 32, pulse primero la tecla D antes de pulsar la tecla de la sección.
Para la sección 33 y posteriores, introduzca el código de sección empleando las teclas numéricas, y
pulse la tecla d, y luego introduzca el precio y pulse de nuevo la tecla d.
4. Repita el paso 3 para todos los artículos de sección.
Visualización de subtotales
5. Pulse la tecla s para visualizar el importe a cobrar.
Finalización de la transacción
6. Introduzca el importe recibido del cliente. (Podrá omitir este paso si el importe recibido es el mismo que el
subtotal.)
7. Pulse la tecla A y se visualizará la vuelta (cuando no se ha introducido el importe recibido, se visualiza
el importe total) y se abrirá el cajón.
8. Corte el recibo y déselo al cliente con su vuelta.
9. Cierre el cajón.
Ejemplo de operación de teclas
Impresión
Asignación de
dependiente
1 L
1500 !
2300 "
s
Membrete gráfico
Registros
de artículos
Fecha/hora/número de código de
dependiente
Número de caja registradora/número
consecutivo/nombre de dependiente
Visualización
del subtotal
5000
Artículos
Precio
Finalización
de la transacción
A
Subtotal de
mercancías
No se imprime
cuando sólo se
venden artículos
no imponibles.
Importe de
impuestos
Estado de impuestos
(T1: imponible 1)
Cantidad total
(En este ejemplo, la tasa de impuestos está
ajustada a 6,25%.)
Importe total
Pago en metálico/importe recibido
Vuelta
5
Función ON/OFF (de emisión/no emisión) de recibos
Cuando emplea la impresora para emitir recibos, podrá inhabilitar la impresión de recibos en el modo REG.
Pulse la tecla
en la posición OP X/Z. Esta tecla cambia el estado de impresión de recibos de ON a OFF.
R
Para emitir un recibo cuando la función de recibo ON/OFF está desactivada (OFF):
Si el cliente quiere el recibo después de haber finalizado la transacción con la función de recibo ON/OFF
desactivada (OFF), pulse la tecla R.
Modo de ahorro de energía
La caja registradora se establecerá en el modo de ahorro de energía cuando no se efectúe ningún registro
basándose en el límite de tiempo ya programado (ajuste inicial de 30 minutos). Cuando la caja registradora se
establezca en el modo de ahorro de energía, se apagará toda la visualización excepto el punto decimal de la
posición de la izquierda. La caja registradora volverá al modo de operación normal al pulsar alguna tecla o al
cambiar un modo.
Aviso de error
2
En los siguientes ejemplos, la caja registradora se coloca en estado de error haciendo sonar un aviso audible y
visualizando el símbolo de error “
las medidas oportunas.
” en el visualizador. Anule el estado de error pulsando la tecla l y tome
• Registra un número de más de 32 dígitos (desborde del límite de registro): Cancele el registro y vuelva a
introducir un número correcto.
• Se equivoca en la operación de teclas: Borre el error y continúe la operación.
• Hace un registro más allá del límite de registro de importes programado: Vea si el importe registrado es
correcto. Si es correcto, puede introducirse en el modo MGR. Llame al administrador.
• Un subtotal con impuestos incluido excede de ocho dígitos: Borre el subtotal pulsando la tecla l y pulse la
tecla A, C o c para finalizar la transacción.
Función de escape de error
Cuando desee abandonar una transacción debido a un error o a un imprevisto, emplee la función de escape de
error como se muestra a continuación:
Para cancelar el estado de error
Transacción
l
E E
La transacción se cancela (se trata como un subtotal cancelado) y se emite el recibo mediante esta función. Si
ya había introducido el importe entregado para el pago, la operación se finaliza como una venta en metálico.
Registros de artículos
3
Registros de un solo artículo
Registros de sección
• Cuando se emplean las teclas de sección (para las secciones 1 a 32)
Cuando utilice un precio unitario programado
1
* Menos que los importes de límite superior
programado
Precio unitario *1
(máx. 7 dígitos)
Tecla de sección
2
*D
Cuando se introduce cero, sólo se añade
la cantidad de ventas.
2
* Para las secciones opcionales 17 a 32,
pulse la tecla de cambio de sección.
6
• Cuando se emplea la tecla de registro de código de sección
Cuando utilice un precio unitario programado
1
* Menos que los importes de límite
superior programado
Cuando se introduce cero, sólo se
añade la cantidad de ventas.
Precio unitario *1
(máx. 7 dígitos)
Código de sección
d
d
(1 a 99)
(En caso de que sólo esté permitido
el registro de precio preajustado.)
Registros de PLU/subsecciones
La caja registradora ya está programada para el modo PLU y cero para el precio unitario. Para emplear
entradas de PLU, deberán haberse programado de antemano sus precios unitarios preajustados. (Consulte la
página 15.) Para emplear los registros de subsecciones, cambie al modo de subsección para los códigos de PLU.
• Registros de PLU
Código de PLU
p
(1 a 1.200)
• Registros de subsección (PLU abierta)
p * Menos que los importes de límite superior
Código de PLU
(1 a 1.200)
Precio unitario*
(máx. 7 dígitos)
p
programado
Cuando se introduce cero, sólo se añade
la cantidad de ventas.
Registros repetidos
Puede utilizar esta función para registrar una venta de dos o más artículos iguales. Repita la pulsación de una
tecla de sección, tecla d o tecla p.
Registros de multiplicación
Cuando venda una gran cantidad de artículos, es conveniente emplear el método de registro de multiplicación.
Introduzca la cantidad empleando las teclas numéricas y pulse la tecla
artículos.
antes de comenzar el registro de
@
Registros de precios divididos
Esta función es práctica cuando un cliente desea comprar artículos que normalmente se venden en lotes. Para
llevar a cabo esta función, deberá cambiar el ajuste programado. Consulte el apartado “Programación 1 de
Cuando emplee un precio unitario programado
Cant. de venta
(hasta 4 dígitos)
Cant. básica
(hasta 2 dígitos)
Precio unitario
por cant. básica
Tecla de sección
@
@
D
d
Código de sección
Precio unitario
por cant. básica
d
(Sólo se permite el registro
preajustado.)
Código de PLU
p
p
Código de PLU
Precio unitario
por cant. básica
p
7
Registros de venta en metálico de un solo artículo (SICS)
• Esta función es útil cuando se vende solamente un artículo en metálico. Esta función es aplicable sólo a las
secciones que se han ajustado para SICS o a sus PLU o subsecciones asociadas.
• Se completa la transacción y el cajón se abre tan pronto como pulse la tecla de sección, la tecla d o la tecla
.
p
Visualización de los subtotales
4
La caja registradora ofrece tres tipos de subtotales:
Subtotal de mercancías
Pulse la tecla
incluir los impuestos, en el visualizador.
en cualquier momento durante la transacción. Aparecerá el subtotal de venta neto, sin
m
Subtotal imponible
Subtotal de imponible 1
Pulse las teclas
y
en este orden en cualquier momento durante la transacción. Aparecerá
T s
el subtotal de venta de los artículos de imponible 1 en el visualizador.
Subtotal de imponible 2
Pulse las teclas
y
en este orden en cualquier momento durante la transacción. Aparecerá
U s
el subtotal de venta de los artículos de imponible 2 en el visualizador.
Subtotal incluyendo los impuestos (subtotal completo)
Pulse la tecla
en cualquier momento durante la transacción. Aparecerán el subtotal de venta con los
s
impuestos incluidos y el símbolo “ ” en el visualizador.
Finalización de una transacción
5
Importe recibido en metálico o cheque
Pulse la tecla
cliente, y entonces pulse la tecla
para obtener un subtotal con impuestos incluidos, registre el importe entregado por el
s
si el importe es en metálico o pulse la tecla
si el importe es un
A
C
cheque. Cuando el importe recibido es mayor que el importe de la venta, la registradora le mostrará el importe
del cambio y se encenderá el símbolo “ ”. De lo contrario, la registradora mostrará un déficit y se encenderá el
símbolo “ ”. Ahora deberá hacer el registro correcto del importe recibido.
Ventas en metálico o cheque que no necesitan un registro
Registre los artículos y pulse la tecla
venta con cheque. La caja registradora visualizará el importe total de la venta.
si se trata de una venta en metálico o pulse la tecla
si es una
A
C
Venta a cargo en cuenta (crédito)
Registre los artículos y pulse la tecla de cargo ( ).
c
Ventas con importe recibido mixto
Podrá efectuar la mezcla de pagos con cheques y metálico, metálico y a cargo en cuenta, y cheque y a cargo
en cuenta.
Por ejemplo: Su cliente paga $9,50 en metálico y $40,00 a cargo a su cuenta para un subtotal de $49,50 con
impuestos incluidos.
Ejemplo de operación de teclas
~
950
A c
s
8
Cálculo de los impuestos
Impuestos automáticos
6
Cuando se ha programado una tasa de impuestos (o tabla de impuestos) en la caja registradora y el estado de
impuestos para una sección individual está ajustado a imponible, la caja calcula los impuestos automáticos para
cualquier artículo que se introduzca directamente en la sección o indirectamente mediante una PLU
relacionada.
Impuestos manuales
La máquina le permite introducir manualmente los impuestos después de haber terminado el registro de
artículos.
Ejemplo: Venta en metálico de un artículo de $8,00 (sección 12) con 50 centavos como impuestos
Ejemplo de operación de teclas
800
50
( t A
Borrado de los impuestos
Podrá borrar los impuestos automáticos en el subtotal de imponible 1 y de imponible 2 de cada transacción
pulsando la tecla
Para efectuar el borrado del subtotal de imponible 1, pulse
1, y entonces pulse
Para efectuar el borrado del subtotal de imponible 2, pulse
2, y entonces pulse
Para borrar todo el subtotal de imponible (1-4), pulse
después de haberse visualizado el subtotal.
t
,
T s
para obtener el subtotal de imponible
para obtener el subtotal de imponible
para borrar el subtotal.
t
,
U s
para borrar el subtotal.
t
,
,
y
T U s t
en este orden.
Cambio del estado de impuestos
La máquina le permitirá cambiar el estado de impuestos programado de cada tecla de sección o de PLU
pulsando las teclas y/o antes de tales teclas. Después de completar cada registro, el estado de
T U
impuestos programado de cada tecla se repondrá al programado.
CARACTERISTICAS OPCIONALES
Registros auxiliares
1
Registros de descuento y recargo empleando la tecla de porcentaje
La tecla de porcentaje se emplea para aplicar un porcentaje de descuento o recargo manualmente introducido o
preajustado a artículos individuales o a un subtotal de mercancías. Para el registro manual del porcentaje de
descuento o de recargo, introduzca el porcentaje (hasta 100,00) con las teclas numéricas (necesitará un punto
decimal cuando introduzca una tasa porcentual fraccionaria), y pulse la tecla de porcentaje. Cuando emplee un
porcentaje preajustado (si se ha programado), pulse tan sólo una tecla de porcentaje.
9
Cálculo porcentual para el subtotal de mercancías
Ejemplo de operación de teclas
~
10
m % A
Cálculo porcentual para registros de artículos
Ejemplo de operación de teclas
800
7
+ P % A
5
Registros de descuento y recargo empleando la tecla de descuento
La tecla de descuento se emplea para aplicar un importe de descuento o recargo manualmente introducido o
preajustado a artículos individuales o a un subtotal de mercancías. Para el registro manual de los importes de
descuento o de recargo, introduzca el importe con las teclas numéricas, y pulse la tecla de descuento. Cuando
emplee un importe preajustado (si se ha programado), pulse una tecla de descuento.
Descuento para el subtotal de mercancías
Ejemplo de operación de teclas
~
100
- A
m
Descuento para registros de artículos
Ejemplo de operación de teclas
675
* - A
Registros de devolución
Para la devolución de un artículo de sección, empiece introduciendo el importe de devolución y pulse la tecla
, y luego pulse la tecla de la sección correspondiente (en el caso de las secciones 17 a 32, pulse la tecla
f
D
y pulse la tecla de la sección correspondiente y, en el caso de las secciones 33 a 99, introduzca el
código de sección, pulse la tecla
y la tecla
, introduzca el importe de devolución y pulse la tecla
).
d
f
d
Para la devolución de un artículo de PLU, introduzca el código de PLU y pulse la tecla
, y luego pulse la
f
tecla
.
p
Para la devolución de un artículo de subsección, introduzca el código de PLU y pulse la tecla
y la tecla
f
, y luego introduzca el importe de devolución y pulse la tecla
.
p
p
Registros e impresión de números de código de no suma
Podrá introducir un número de código de no suma, como pueda ser un número de código de cliente o número
de tarjeta de crédito, con un máximo de 16 dígitos, en cualquier momento durante el registro de una venta. La
caja registradora lo imprimirá.
Para introducir un número de código de no suma, introduzca el número y pulse la tecla
.
s
Tratos de pagos auxiliares
Conversión de divisas
2
La caja registradora permite registros de pago con divisas (sólo está disponible el pago en metálico). Pulsando
la tecla se crea un subtotal en la divisa en cuestión.
V
Cuando emplee una tasa de cambio de divisas programada, pulse la tecla
después de los registros de los
V
artículos, e introduzca entonces el importe recibido en la divisa si no se trata de un pago con el importe justo, y
pulse la tecla
Cuando efectúe un registro manual de la tasa de cambio de divisas, después de los registros de todos los
.
A
artículos, introduzca la tasa de cambio (0,0000 a 9999,9999; necesitará un punto decimal cuando introduzca
una tasa de cambio fraccionaria), y pulse la tecla
no es un pago del importe justo, y pulse la tecla
En ambos casos, la vuelta se visualizará en moneda nacional y, cuando el importe recibido sea insuficiente, el
, y luego introduzca el importe en la divisa en cuestión si
.
V
A
déficit se mostrará en moneda nacional.
10
• Pulse la tecla
después de pulsar la tecla
para cancelar el pago en una divisa.
l
V
•
Si se programa, se imprime un símbolo de moneda extranjera.
Registros de recibido a cuenta y de pagado
Cuando recibe un pago a cuenta o cuando usted paga a un abastecedor, es aconsejable emplear la tecla
o
r
la tecla
respectivamente. Los pagos en metálico sólo están disponibles en la operación RA y PO.
R
Para el registro de recibido a cuenta, introduzca el importe y pulse la tecla
.
r
Para el registro de pagado, introduzca el importe y pulse la tecla
.
R
Sin ventas (cambios)
Cuando deba abrir el cajón para algo que no sea una venta, pulse tan sólo la tecla
registradora imprimirá “NO VENTA” en el registro diario o en el recibo.
. El cajón se abrirá y la
A
Registros con tecla de secuencia automática (tecla
)
a
3
Puede lograr una transacción programada pulsando simplemente la tecla
.
a
CORRECCION
Corrección del último registro (cancelación directa)
1
Si hace un registro incorrecto relativo a una sección, PLU/subsección, porcentaje (
y
), descuento ( ) o
% &
-
devolución, puede cancelar este registro pulsando la tecla
inmediatamente después del registro incorrecto.
v
Corrección del registro siguiente al último o anterior (cancelación indirecta)
2
Podrá cancelar cualquier registro de sección incorrecto, registro de PLU/subsección o registro de devolución de
artículo hechos durante una transacción, si lo encuentra antes de finalizar la transacción (por ejemplo, pulsando
la tecla
). Esta función es aplicable sólo a los registros de sección, PLU/subsección y de devolución.
A
Para la operación, pulse la tecla
Para la cancelación indirecta de devolución, pulse la tecla
justo antes de pulsar una tecla de sección, la tecla
, o la tecla
.
v
d
p
después de haber pulsado la tecla
.
v
f
Cancelación del subtotal
3
Puede cancelar una transacción completa. Una vez ejecutada la cancelación del subtotal, la transacción se
detiene y la registradora emite un recibo. Esta función no funciona cuando se han introducido más de 30
artículos.
Ejemplo de operación de teclas
1310
10
" p s v s
Cancelación de subtotal
11
PARA EL ADMINISTRADOR
PROGRAMACION DE LAS
FUNCIONES BASICAS (Para el inicio rápido)
Para programar la caja registradora, ponga la llave del administrador en el selector de modo y gírela a la
posición PGM.
Programación de la fecha y de la hora
Fecha
1
Para ajustar la fecha, introduzca la fecha con 8 dígitos empleando el formato de mes-día-año (MM/DD/AAAA), y
pulse entonces la tecla s.
Ejemplo de operación de teclas
08262002
s
(Agosto 26, 2002)
Hora
Para ajustar la hora, introduzca la hora con 4 dígitos empleando el formato de 24 horas. Por ejemplo, para
ajustar la hora a las 2:30 AM, introduzca 230; y para ajustarla a las 2:30 PM, introduzca 1430.
Ejemplo de operación de teclas
1430
s
Programación de los impuestos para la función de cálculo automático de los impuestos
2
Antes de poder proceder al registro de ventas, primero deberá programar los impuestos que se cargan de
acuerdo con las leyes de su estado. En esta caja registradora pueden programarse cuatro tasas de impuestos
distintas. En la mayor parte de estados, sólo será necesario programar los impuestos 1. Sin embargo, si vive en
una zona que tiene impuestos locales propios o impuestos de hospitalidad, podrá programar la caja registradora
para que calcule estos impuestos por separado.
Cuando programe el estado de impuestos para una sección, los impuestos se añadirán automáticamente a los
artículos de venta asignados a la sección de acuerdo con el estado de impuestos programado para la sección.
También podrá introducir manualmente los impuestos.
Hay dos métodos para programar los impuestos. El método de la tasa de impuestos emplea una tasa
porcentual directa por dólar. El método de tabla de impuestos requiere la información detallada de impuestos
para las oficinas de impuestos estatales o locales. Emplee el método que sea aceptable para su estado. Podrá
obtener los datos necesarios en la oficina de impuestos local para efectuar la programación de los impuestos.
Programación de los impuestos empleando una tasa de impuestos
La tasa porcentual aquí especificada se emplea para calcular los impuestos sobre subtotales imponibles.
*Número de impuestos (1 a 4)
@
s 9 @
Cuando el importe imponible más bajo es cero
Tasa de impuestos
(0,0000 a 100,0000)
Importe imponible más bajo
@
s A
(0,01 a 999,99)
12
Ejemplo: Programación de la tasa de impuestos del 4% como tasa de impuestos 2 con exención de impuestos
de 12¢
Ejemplo de operación de teclas
9
s @ @ @ s A
2
4
12
Tabla de impuestos (aplicable al impuesto añadido)
Si se encuentra en una localidad que emplea una tabla de impuestos para el cálculo de los impuestos, podrá
programar consecuentemente la caja registradora. La programación de la tabla de impuestos puede efectuarse
para impuestos 1 a impuestos 4.
Tabla de impuestos de muestra
Tabla de impuestos de New Jersey: 6%
A: Diferencia entre el
punto de división mínimo
y el siguiente (¢)
Margen de importe de venta
Impuestos Punto de división mínimo
Punto de división máximo
.00
.01
.02
.03
.04
.05
.06
.07
.08
.09
.10
.11
.12
.13
.01
.11
.23
.39
.57
.73
.89
a
a
a
a
a
a
a
a
a
a
a
a
a
a
.10
–
B: No cíclico
T
Q
.22
.38
10 (0.11 - 0.01)
12 (0.23 - 0.11)
16 (0.39 - 0.23)
18 (0.57 - 0.39)
16 (0.73 - 0.57)
16 (0.89 - 0.73)
22 (1.11 - 0.89)
12 (1.23 - 1.11)
16 (1.39 - 1.23)
18 (1.57 - 1.39)
16 (1.73 - 1.57)
16 (1.89 - 1.73)
22 (2.11 - 1.89)
.56
.72
C: Cíclico 1
.88
1.10
1.22
1.38
1.56
1.72
1.88
2.10
2.22
1.11 M1
1.23
1.39
1.57
D: Cíclico 2
1.73
1.89
2.11 M2
Para programar una tabla de impuestos, primero haga una tabla como la tabla de la derecha arriba mostrada.
Partiendo de la tabla de impuestos, calcule las diferencias entre el punto de división mínimo y el siguiente (A).
Luego, partiendo de las diferencias, busque ciclos irregulares (B) y ciclos regulares (C y D). Estos ciclos le
mostrarán los elementos necesarios para programar la tabla de impuestos:
T: El importe de impuestos recolectados en el importe imponible mínimo (Q)
Q: El importe imponible mínimo
M1: El valor máximo del punto de división mínimo en un ciclo regular (C)
A esto lo denominamos “punto MAX”.
M2: El valor máximo del punto de división mínimo en un ciclo regular (D)
A esto lo denominamos “punto MAX”.
M: Margen del punto de división mínimo en un ciclo regular: diferencia entre Q y M1 o entre M1 y M2.
*2
Tasa
*1
Número de uno
o dos dígitos
M
s 8 @
@
@
@
máx. de seis dígitos
(0,0001 - 99,9999%)
máx. de
cuatro dígitos
Punto de división mínimo
máx. de cinco dígitos
T
Q
@
@
@ A
máx. de
máx. de
cinco dígitos
tres dígitos
Repetir hasta que se introduzca el punto MAX.
13
Este primer número que se introduce depende de si la diferencia entre un punto de
división mínimo a introducirse y el punto de división mínimo anterior no son de menos
de $1,00 ni de más de 99¢. Cuando la diferencia no sea de menos de $1,00, introduzca
“1”, y cuando no sea de más de 99¢, introduzca “0” o no introduzca nada.
El segundo número depende de si su tabla de impuestos debe programarse como tabla
de impuestos 1, 2, 3, ó 4.
*1 Primer número:
(1 ó 0)
Segundo número:
(1 a 4)
*2 Si la tasa es fraccionaria (por ejemplo 4-3/8%), la fracción (3/8) se convierte a su equivalente decimal (es
decir, 0,375) y se introduce la tasa resultante de 4,375. Tenga presente que la tasa nominal (R)
generalmente se indica en la tabla de impuestos.
• Limitaciones para el registro de puntos de división mínimos
La caja registradora puede trabajar con una tabla de impuestos que conste hasta de 72 puntos de división como
máximo. (El número máximo de puntos de división es de 36 cuando la diferencia de puntos de división es de
$1,00 o más.) Si el número de puntos de división excede la capacidad de tablas de la caja registradora, deberá
emplear entonces el registro manual.
PROGRAMACION DE FUNCIONES AUXILIARES
Programación de secciones
1
La mercancía se puede clasificar en un máximo de 99 secciones.
Estado de sección
*
Para ajustar todo ceros
D
ABCDEFGH
Tecla de sección
@
A
*Para programar las secciones 17 a 32, pulse la tecla de cambio de sección en este punto.
Para las secciones 33 a 99:
Para ajustar todo ceros
ABCDEFGH
Código de sección
d
@
A
Para programar otra sección, comience desde el principio sin pulsar la tecla
.
A
Elemento:
Selección:
Imponible
Registro:
A
B
C
D
E
F
Estado de impuestos 4
1
0
No imponible
Imponible
Estado de impuestos 3
Estado de impuestos 2
Estado de impuestos 1
SICS / Normal
1
No imponible
Imponible
0
1
No imponible
Imponible
0
1
No imponible
SICS
0
1
Normal
0
Signo
Sección negativa
Sección positiva
1
0
G
H
Límite de dígitos de entrada
0-7
3
Tipo de registros de precio unitario
Abertura y preajuste
Sólo preajuste
2
Sólo abertura
1
Tecla de sección invalidada
0
14
Estado de impuestos (imponible 1 a 4 / no imponible)
• Cuando se efectúa un registro de una sección imponible en una transacción, los impuestos se calculan
automáticamente de acuerdo con la tabla o tasa de impuestos asociada.
SICS (Venta en metálico de un solo artículo)
• Si se efectúa primero un registro de una sección programada para SICS, la venta se finalizará como venta de
pago en metálico así que se pulse la tecla de la sección.
Límite de dígitos de entrada
• El límite es eficaz para operaciones en el modo REG y puede pasarse por alto en el modo MGR.
Precio unitario preajustado
*
Para programar cero
D
Precio unitario
Tecla de sección
A
*Para programar las secciones 17 a 32, pulse la tecla de cambio de sección en este punto.
(máx. seis dígitos)
Para las secciones 33 a 99:
Para programar cero
Precio unitario
(máx. seis dígitos)
Código de sección
d
s
A
Para programar otra sección, comience desde el principio sin pulsar la tecla
.
A
Programación de PLU (codificación de precios) y subsección
2
La función de PLU permite realizar registros rápidos con las teclas en los que el precio se busca
automáticamente al introducir un código. La subsección es un tipo de “PLU abierta”, que requiere que usted
introduzca un precio detrás del código de PLU. Pueden realizarse un máximo de 1.200 ajustes de
PLU/subsección. Cada una pertenece a una sección y adquiere los parámetros de la sección (estado de
impuestos, SICS y signo).
La caja registradora ya está programada de modo que los 1.200 códigos están asignados a las PLU asociadas
con la sección 1 y precio unitario preajustado “0”.
Asignación de precios unitarios y de secciones asociadas
1
*D
Para programar cero
Precio unitario*3
Tecla de sección
*2Código de PLU
A
p
*1: Para asignar las secciones 17 a 32, pulse la tecla de cambio de sección en este punto.
(máx. seis dígitos)
asociada
Cuando la sección asociada es una de las secciones 33 a 99:
Para programar cero
Precio unitario*3
(máx. seis dígitos)
Código de
sección asociada
*2Código de PLU
d
s
p
A
(1 a 99)
*2: 1 a 1.200 (Dependiendo del ajuste del tamaño de la memoria EJ, hasta 200)
*3: Para una subsección, ajuste el importe de límite del registro de precio unitario.
Para borrar un código de PLU, emplee la secuencia siguiente:
Código de PLU
p v A
Para borrar la PLU siguiente
Para borrar otra PLU
15
Selección de PLU/subsección
Para programar “0”
*1Código de PLU
*2A
p
s A
Para programar la PLU siguiente
Para programar otra PLU
*1: 1 a 1.200 (Dependiendo del ajuste del tamaño de la memoria EJ, hasta 200)
*2: 0 para la subsección o 1 para PLU
Programación de teclas misceláneas
3
Tasa para
,
y
% & V
Para programar cero
*Tasa
o
% & A
V
Para programar otra tasa
*: Tasa
0,00 – 100,00 (Tasa de porcentaje)
0,0000 – 9999,9999 (Tasa de conversión de divisas)
Deberá emplear un punto decimal para
ajustar tasas fraccionarias.
Importe para
-
Para programar cero
Importe de descuento (máx. seis dígitos)
- A
Límite de tasa porcentual para
y
% &
Para programar cero
o
Límite de porcentaje (0,00 - 100,00%)
% & A
Para programar otra tecla de porcentaje
s 29 @
• Los registros porcentuales que exceden al límite superior pueden suprimirse en el modo MGR.
• 10,00% puede registrarse como . La tecla es
o
10 10P00
P
necesaria sólo para los registros fraccionarios.
16
Parámetros de función para
,
% & -
y
Para programar “0” para todos los artículos
*ABCDEFGH
o
@ % & A
-
Para programar otra tecla
*: Elemento:
Selección:
Imponible
Registro:
A
B
C
D
E
F
Estado de impuestos 4
1
0
No imponible
Imponible
Estado de impuestos 3
Estado de impuestos 2
Estado de impuestos 1
Signo +/-
1
No imponible
Imponible
0
1
No imponible
Imponible
0
1
No imponible
Signo + (recargo)
Signo - (descuento)
Habilitar
0
0
1
% de artículo / de artículo
0
_
Inhabilitar
1
G
H
% de subtotal / de subtotal
Habilitar
0
_
Inhabilitar
1
Límite de dígitos de entrada para la tecla
de descuento
0-7
Cuando se programen las teclas de porcentaje, introduzca siempre 0 para H.
El límite de dígitos de entrada es eficaz para operaciones en el modo REG, pero puede suprimirse en el
modo MGR.
Parámetros de función para
V
Para programar “0” para todos los artículos
*AB
@ V A
*: Elemento:
A
Selección:
Registro:
Registro de tasa abierta
Habilitar
Inhabilitar
Habilitar
Inhabilitar
0
1
0
1
B
Registro de tasa preajustada
Límite de dígitos de entrada para
,
r R t
y
Límite de dígitos de entrada
o
@ r, R t A
(sólo para entrada manual)
• Para
, introduzca 0 a 9 (dígitos), y para
(impuestos manuales), introduzca 0 a 7 (dígitos).
r R
t
El límite de dígitos de entrada es de hecho para operaciones en el modo REG, pero puede suprimirse en el
modo MGR.
17
Parámetros de función para
,
C c A
y
(cuando se usa como tecla CA)
Para programar “0” para todos los artículos
2
*
*1ABC
o
@ s, C c A
Para programar otra tecla
*2: Pulse la tecla
s para ajustar la tecla CA.
*1:Elemento:
Selección:
Registro:
A
Impresión de pie del recibo
Habilitar
1
0
Inhabilitar
B
Registro de importe recibido
Obligatorio
1
No obligatorio (para la tecla CA o CHK)
Invalidar (para la tecla CH)
0
0
C
Límite de dígitos de entrada
0-8
Impresión de pie del recibo
• Esta programación decide si la registradora debe imprimir un mensaje en la parte inferior del recibo cuando
se usa una de estas teclas de finalización especificada. Con respecto al método de programación del
Límite de dígitos de entrada
• Para las teclas
y
, programe un importe de entrada de límite superior para el importe recibido. Para la
c C
tecla
, programe un importe de entrada de límite superior para el importe total en metálico que puede
A
manipularse en la caja registradora.
Programación de texto
4
La caja registradora le permite programar textos para los nombres de dependiente, nombres de artículos de
sección, nombres de artículos de PLU/subsección, etc., cuando sea necesario. Hay dos formas de programar el
texto: empleando las teclas de caracteres del teclado o introduciendo los códigos de los caracteres con las
teclas numéricas del teclado.
Empleo de las teclas de caracteres del teclado
Podrá introducir caracteres de acuerdo con los caracteres pequeños que hay en la esquina inferior derecha de
las teclas. Para ver la disposición, consulte la sección “Teclado” de la página 5 de la versión inglesa.
Las teclas siguientes se emplean como teclas de control para la entrada de caracteres:
Cambia entre letras mayúsculas y minúsculas. El ajuste inicial es el de letras mayúsculas
H
seleccionadas. Una vez se ha pulsado la tecla
, se fija la entrada para letras minúsculas. “_” se
H
enciende en la posición SHIFT del visualizador cuando se selecciona la entrada de letras minúsculas.
Pulse la tecla para introducir caracteres numéricos. Por ejemplo para introducir “1”, pulse la tecla
N
N
1
y la tecla
. Si pulsa la tecla
sin pulsar la tecla
, la caja registradora se establece en
N
N
1
el modo de entrada de códigos de caracteres.
Una vez se ha pulsado la tecla , se fija la entrada para caracteres numéricos. “_” se enciende en
N
la posición NUMBER del visualizador cuando se selecciona la entrada de caracteres numéricos.
Cambia entre caracteres de tamaño normal y de tamaño doble. En el ajuste inicial se han seleccionado
W
B
los caracteres de tamaño normal. Una vez se pulsa la tecla
tamaño doble. “_” se enciende en la posición DC del visualizador cuando se selecciona la entrada de
, se fija la entrada para caracteres de
W
caracteres de tamaño doble.
Hace retroceder el cursor, borrando el carácter de la izquierda.
18
Para programar la palabra “Clerk01” con la letra “C” de tamaño doble.
Para que la letra “C” sea de tamaño doble
W g
W
Para que el tamaño de los caracteres vuelva al normal
Para cambiar a letras minúsculas
H
h i j k
N 0 1
Para introducir números
Introducción de códigos de caracteres con las teclas numéricas del teclado
Los números, las letras y los símbolos pueden programarse introduciendo el código de carácter y la tecla
.
:
(Si se selecciona la entrada de caracteres numéricos, es decir, “_” se enciende en la posición NUMBER del
visualizador, pulse la tecla para que se apague.) Prepare la tabla de códigos de caracteres alfanuméricos
N
de la página siguiente. De este modo, podrá programar caracteres distintos a los que hay en las teclas.
• Pueden obtenerse caracteres de tamaño doble introduciendo el código de caracteres 253.
• DEBEN introducirse los tres dígitos del código del carácter (aunque empiece con cero).
Para programar la palabra “SHARP” en caracteres de tamaño doble.
253
083
072
065
082
080
: : : : : :
S
H
A
R
P
Cuando pulsa una tecla del número apropiado (número de código de tarea) y pulsa la tecla
para entrada de
P
texto justo después de haber comenzado la programación con la tecla
, la caja registradora quedará
s
automáticamente preparada para la entrada siguiente.
inglesa.
Texto de sección
*
Para mantener el ajuste vigente
D
Tecla de
sección
Teclas de caracteres
(máx. 12 dígitos)
s 1 P
s A
Código de sección
d
(1 a 99)
Para programar otra sección
*Para programar las secciones 17 a 32, pulse la tecla de cambio de sección.
Ejemplo de operación de teclas
1
s P !
FRUTA
(Programación de FRUTA para la sección 1)
s A
Texto de PLU (etiqueta de artículo)
Para mantener el ajuste vigente
Teclas de caracteres
(máx. 12 dígitos)
Código
de PLU
s A
s 2 P
p
Cuando el siguiente código de PLU sigue
inmediatamente al que se acaba de introducir
Para programar otra PLU
19
Texto de función
Para mantener el ajuste vigente
Teclas de caracteres
*Número de función
(máx. 8 dígitos)
s 3 P
(máx. 2 dígitos)
@
s A
Para programar el texto de otra función
* Número de función: Vea la “Lista de textos de función” mostrada a continuación.
Lista de textos de función
Número
Número
Tecla o función
Tecla o función
Ajuste inicial
Ajuste inicial
ANULA
de función
de función
(–)
Modo de cancelación
1
2
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
%1
%2
%1
Cancelación del administrador ANUL MGR
%2
Cancelación de subtotal
Sin venta
ANUL ST
NO VENTA
RECI. CTA
PAGOS
3
Total neto de ventas
NETO 1
4
Subtotal neto de imponible 1 TASABLE1
Recibido a cuenta
Pagos
5
Total bruto de impuestos 1
Total de impuestos 1 de registros de devoluciones
Total neto de impuestos 1
Exención de impuestos 1
TAX1 GRS
TAX1 DEV
TAX1
6
Contador de clientes
Total de ventas
Metálico
TRANSAC.
NETO 3
7
8
TX1 EXNT
CAJA
9
Subtotal neto de imponible 2 TASABLE2
Cheque
CHEQUE
CREDITO
CREDITO–
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
Total bruto de impuestos 2
Total de impuestos 2 de registros de devoluciones
Total neto de impuestos 2
Exención de impuestos 2
TAX2 GRS
TAX2 DEV
TAX2
Cargo bruto
Cargo de devoluciones
Conversión de divisas 1 (preajustada) DIVISA 1
Conversión de divisas 2 (abierta) DIVISA 2
TX2 EXNT
Subtotal neto de imponible 3 TASABLE3
Metálico en el cajón
EFEC. CAJ
Total bruto de impuestos 3
Total de impuestos 3 de registros de devoluciones
Total neto de impuestos 3
Exención de impuestos 3
TAX3 GRS
TAX3 DEV
TAX3
Metálico+cheque en el cajón CACH CAJ
Cambio de cheques
Exento de IVA
Total de secciones (+)
Total de secciones (–)
Subtotal
CAMB. CH
IVA EXNT
DEPT TL
DEPT(–)
53
*
TX3 EXNT
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
Subtotal neto de imponible 4 TASABLE4
Total bruto de impuestos 4
Total de impuestos 4 de registros de devoluciones
Total neto de impuestos 4
Exención de impuestos 4
TAX4 GRS
TAX4 DEV
TAX4
SUBTOTAL
ST MERCA
TOTAL
Subtotal de mercancías
Total
TX4 EXNT
Cambio
CAMBIO
Total bruto de impuestos manuales MTAX GRS
Total de impuestos manuales de devoluciones MTAX DEV
Total neto de impuestos manuales M-TAX
Total de exención desde GST GST EXNT
Artículos
ARTICULO
Título de informe de secciones DEPT
Título de informe de PLU
PLU
Título de informe de transacciones TRANS.
Título de informe de dependientes EMPLEADO
28
*
Total de PST
Total de GST
Total de impuestos
Neto
PST TTL
GST TTL
TTL TAX
NETO
29
*
Título de informe horario
Símbolo de no adición
Título de copia de recibo
Título de informe EJ
HORARIO
30
*
#
31
32
33
34
35
COPIA
EJ
Total de ventas incluyendo el total de impuestos NETO 2
Devoluciones
DEVOLUC.
ANUL ART
Título de fin de informe EJ
FIN EJ
Cancelación de artículos
Los elementos marcados con “ ” son sólo para Canadá.
*
20
Nombres de dependiente
Para mantener el ajuste vigente
Código de
Teclas de caracteres
dependiente
(1-15)
s 5 P
@
Para programar otro dependiente
s A
(máx. 8 dígitos)
Mensajes de membrete
La caja registradora puede imprimir mensajes programados en cada recibo. En el modelo estándar, se imprime
el membrete gráfico en el recibo. Si desea imprimir mensajes de membrete, cambie el formato de impresión de
membrete. (Para los detalles de la programación, vea la página 27.) A continuación se enumeran las opciones:
Para mantener el ajuste vigente
*Número
de líneas
(1-6)
Teclas de caracteres
(máx. 24 dígitos)
s 4 P
@
s A
Para programar otra línea
* Tipo de “Mensaje de 3 líneas de encabezamiento”: 1 a 3
Tipo de “Mensaje de 3 líneas de pie de recibo”: 4 a 6
Tipo de “Mensaje de 6 líneas de encabezamiento”: 1 a 6
Tipo de “Mensaje de 3 líneas de encabezamiento y 3 líneas de pie de recibo”: 1 a 6 (1 a 3 como
encabezamiento, 4 a 6 como pie de recibo)
Símbolo de divisas
El símbolo de divisas para la tecla
se imprime con un importe de cambio de divisas.
V
Para mantener el ajuste vigente
Teclas de caracteres
s 6 P
s A
(máx. 4 dígitos)
21
PROGRAMACION AVANZADA
Programación de número de caja registradora y de número consecutivo
1
El número de caja registradora y el número consecutivo se imprimen en el recibo o en el registro diario.
Número de caja registradora
Para ajustar a “0” el número de la caja registradora
Número de caja registradora (de uno a seis dígitos)
@
s
s 1
A
Ajuste de números consecutivos
Para empezar a contar desde 0001
Un número (de uno a cuatro dígitos) que
sea inferior en uno al número inicial deseado
@
s A
s 2
Programación del registro diario electrónico (EJ)
2
La caja registradora incorpora la función de registro diario electrónico (EJ). En el ajuste inicial, pueden
almacenarse un máximo de 1.000 líneas en la memoria. Si desea almacenar más datos de registro diario, podrá
ampliarla hasta un máximo de 2.000 líneas.
Para leer los datos del registro diario, consulte el apartado de “LECTURA Y REPOSICION DE INFORMES EJ”
Tipo de memoria de EJ
Cuando se ejecuta este procedimiento, los datos de EJ se borran y los datos de PLU (datos de
programación y datos de ventas) se reponen a los valores de ajuste inicial después de haber
borrado todos los datos aunque se seleccione el mismo tipo de la memoria.
*A
s 90 @
A
*A: 0 para 1.000 líneas de EJ y 1.200 códigos de PLU
1 para 2.000 líneas de EJ y 200 códigos de PLU
Parámetros de función para el EJ
Para ajustar “00000000”
*ABCDEFGH
s 68 @
s A
22
* Elemento:
Selección:
Registro:
A
B
C
Introduzca siempre 0.
(Posición fija)
0
0
0
1
0
1
0
1
0
1
0
1
0
1
2
Introduzca siempre 0.
Impresión temporal de EJ durante la
transacción
(Posición fija)
Inhabilitar
Habilitar*
D
E
F
Impresión de EJ y borrado de datos de
EJ cuando se emite el informe Z1 general
No*
Sí
Tipo de registros de operación en el
modo PGM
Detalles*
Sólo información de encabezamiento
Detalles*
Tipo de registros de operación en el
modo REG/MGR/VOID
Total
G
H
Impresión comprimida para datos de EJ
No (tamaño normal)
Sí (tamaño pequeño)*
Continuar
Acción cuando el área de memoria de
EJ está llena
Avisar (aviso de casi llena)*
Bloqueo (con aviso de casi llena)
En el ajuste inicial, se marca un asterisco.
Impresión temporal de EJ durante la transacción
• Si selecciona “Sí”, podrá imprimir los datos del registro diario de la transacción actual registrada en la
memoria de EJ pulsando la tecla durante la transacción. Para poder realizar esta función por completo,
R
la caja registradora está programada para la impresión del recibo y la función de activación/desactivación
(ON/OFF) de recibo está desactivada (OFF).
Tipo de registros de operación en el modo PGM
• Para la operación de lectura de datos de programación, se imprime sólo la información del encabezamiento.
Para informes X/Z, se imprime sólo la información del encabezamiento.
Acción cuando el área de memoria de EJ está llena
• Según el ajuste inicial, cuando la memoria para EJ está casi llena, la caja registradora muestra puntos
decimales en las posiciones octava y novena del visualizador (mensaje de memoria EJ casi llena), y la caja
registradora sigue almacenando nuevos datos mientras va borrando los más antiguos. Cuando se seleccione
“0”, la caja registradora no mostrará el mensaje de memoria EJ casi llena. Cuando se seleccione “2”, la caja
registradora mostrará el mensaje de memoria EJ casi llena y cuando se llene la memoria, la caja registradora
bloqueará la entrada de ventas/datos con una visualización del mensaje de memoria llena “
”. Sólo
podrá emitir un informe EJ.
Programación 1 de selección de diversas funciones
3
La caja registradora ofrece varias funciones detalladas como las que se mencionan a continuación.
• Selección de función para teclas misceláneas
• Formato de impresión
• Formato de impresión de recibos
• Selección de función para impuestos
• Otras
Para esta programación, se aplica el estilo de entrada de código de tarea. Podrá seguir la programación hasta
que pulse la tecla para la programación que se describe a continuación. Para seguir la programación,
A
repita desde la entrada de un código de tarea.
Para ajustar “00000000”
*1Código de tarea
*2ABCDEFGH
s
@
s A
*1 Introduzca el código de tarea empleando las teclas numéricas especificadas en cada sección de abajo.
*2 Los detalles de la entrada de datos se enumeran en cada tabla de cada sección de abajo. Se introduce un
asterisco para indicar el ajuste de fábrica.
23
Selección de función para teclas misceláneas
Código de tarea: 5
* Elemento:
Selección:
Registro:
A
B
C
D
E
F
PO en el modo REG
Habilitar la operación PO en el modo REG*
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
Inhabilitarla
RA en el modo REG
Habilitar la operación RA en el modo REG*
Inhabilitarla
Cancelación de subtotal en el modo
REG
Habilitar la cancelación de subtotal en el modo REG*
Inhabilitarla
Cancelación indirecta en el modo REG
Habilitar la cancelación indirecta en el modo REG*
Inhabilitarla
Cancelación directa en el modo REG
Habilitar la cancelación directa en el modo REG*
Inhabilitarla
Disponibilidad de la tecla de
devoluciones
Habilitar registros de devolución en el modo REG*
Inhabilitarla
G
H
No venta en el modo REG
Habilitar las operaciones de no venta en el modo REG*
Inhabilitarla
Disponibilidad de cantidades
fraccionarias
Habilitar el registro de cantidades fraccionarias
Inhabilitarla*
Formato de impresión
Código de tarea: 6
* Elemento:
Selección:
Registro:
A
B
C
D
E
Estilo de impresión
Empleo de la impresora para impresión del registro diario
Empleo de la impresora para impresión de recibos*
Total
0
1
0
1
0
1
0
1
0
1
0
0
1
0
1
Formato de impresión de recibos
Detallado*
Impresión de la hora en todos los
recibos/registro diario
Habilitar la impresión de la hora*
Inhabilitarla
Impresión de la fecha en todos los
recibos/registro diario
Habilitar la impresión de la fecha*
Inhabilitarla
Impresión del N.° consecutivo en todos
los recibos/registro diario
Habilitar la impresión del N.° consecutivo*
Inhabilitarla
F
Introduzca siempre 0.
(Posición fija)
G
Salto de ceros para informe de PLU
Inhabilitar el salto de ceros
Habilitar el salto de ceros*
H
Salto de ceros para informes generales, Inhabilitar el salto de ceros
de dependientes y horarios
Habilitar el salto de ceros*
Estilo de impresión
• Incluso cuando se selecciona la impresión de recibos, el motor de rebobinado del registro diario será
accionado en los modos PGM, OP X/Z, X1/Z1 y X2/Z2 para poder bobinar los informes de ventas y de
programación.
Formato de impresión de recibos
Código de tarea: 7
* Elemento:
Selección:
(Posición fija)
(Posición fija)
Registro:
A
B
C
Introduzca siempre 0.
0
0
0
1
0
1
0
0
0
0
1
Introduzca siempre 0.
Impresión de subtotal con una pulsación Inhabilitar la impresión de subtotales*
de la tecla de subtotal
Impresión de mercancías con una pulsa- Inhabilitar la impresión de subtotal de mercancías*
Habilitarla
D
ción de la tecla de subtotal de mercancías
Habilitarla
E
F
Introduzca siempre 0.
(Posición fija)
Introduzca siempre 0.
(Posición fija)
G
H
Introduzca siempre 0.
(Posición fija)
Impresión del número de compras
Habilitar la impresión del número de compras*
Inhabilitarla
24
Selección de función para impuestos
Código de tarea: 15
* Elemento:
Selección:
Registro:
A a F
Introduzca siempre 0.
(Posición fija)
0
0
1
0
1
G
Disponibilidad de borrado de los
impuestos en el modo REG
Habilitar el borrado de impuestos en el modo REG*
Inhabilitarla
H
Disponibilidad de entrada de impuestos Habilitar la entrada de impuestos manuales en el modo REG*
manuales en el modo REG
Inhabilitarla
Otras programaciones
Código de tarea: 61
* Elemento:
Selección:
Registro:
A
B
C
Introduzca siempre 0.
(Posición fija)
0
0
0
1
0
1
2
0
1
0
1
0
1
2
Introduzca siempre 0.
(Posición fija)
Disponibilidad de sección y PLU/
subsección negativas
Inhabilitar la programación de sección y PLU/subsección negativas
Habilitarla*
D
Trato fraccionario
Redondeo (4 por defecto, 5 por exceso)*
Aumento a la unidad
Descartar el trato fraccionario
E
F
Empleo de la tecla
Formato de la hora
Empleo de la tecla
Empleo de la tecla
como tecla 00*
como tecla 000
:
:
:
Empleo del formato de 12 horas*
Empleo del formato de 24 horas
Empleo del formato de mes-día-año*
Empleo del formato de día-mes-año
Empleo del formato de año-mes-día
G
Formato de la fecha
H
Posición del punto decimal (desde la
derecha) (TAB)
0 a 3
(ajuste inicial: 2)
Código de tarea: 62
* Elemento:
Selección:
Registro:
A
B
Introduzca siempre 0.
(Posición fija)
0
0
1
0
1
0
1
0
1
0
Activación del pitido de error
Por error de bloqueo*
Por operación incorrecta
C
D
E
F
Disponibilidad del sonido de
accionamiento de teclas
Habilitar el sonido*
Inhabilitarla
Teclado con memoria intermedia
Sí*
No
Disponibilidad de la operación del
modo de cancelación
Habilitar la operación del modo de cancelación*
Inhabilitarla
Habilitar la impresión de datos de entradas en el
modo de cancelación en los informes Z2*
Impresión de datos de entradas en el
modo de cancelación en los informes Z2
Inhabilitarla
1
0
G
H
Impresión de datos de entradas en el
modo de cancelación en los informes Z1
Habilitar la impresión de datos de entradas en el
modo de cancelación en los informes Z1*
Inhabilitarla
1
0
1
Adición de datos de total de ventas
horario en el modo de cancelación
No*
Sí
25
Código de tarea: 66
* Elemento:
Selección:
Registro:
A
B
C
Impresión de un recibo después de la
transacción
Sólo el total
0
1
0
1
0
1
0
0
1
0
1
Detalles*
Impresión del importe cuando el precio
unitario de PLU/subsección es cero
Inhabilitar la impresión*
Habilitarla
Impresión del subtotal para conversión
de déficit
Habilitar la impresión*
Inhabilitarla
D
E
Introduzca siempre 0.
(Posición fija)
Impresión comprimida en el registro diario Inhabilitar la impresión comprimida (tamaño normal)
en los modos PGM, OP X/Z, X1/Z1 y X2/Z2
Habilitar la impresión comprimida (tamaño pequeño)*
Inhabilitar la impresión comprimida (tamaño normal)
Habilitar la impresión comprimida (tamaño pequeño)*
F
Impresión comprimida en el registro
diario en los modos REG, MGR y VOID
G
H
Impresión del mensaje del membrete
en el registro diario
Inhabilitar la impresión del mensaje del membrete en el registro diario*
Impresión de pie de recibo en todos los recibos*
0
1
0
1
Impresión de pie de recibo
Impresión de pie de recibo con la tecla de función
seleccionada en el momento de la finalización
Impresión comprimida
• Esta programación sólo es válida cuando se selecciona la impresión del registro diario. No afecta la
impresión de EJ. (Para la programación de EJ, consulte la página 22.)
Código de tarea: 70
* Elemento:
Selección:
Registro:
A
Cómputo de precios divididos
Cantidad*
0
1
0
Paquete
B
Disponibilidad de entrada de precios
con multiplicación/división
Habilitar sólo la entrada de multiplicación*
Habilitar la entrada de multiplicación y la de división de precios
(Posición fija)
1
C
D
E
Introduzca siempre 0.
Introduzca siempre 0.
Impresión de impuestos cuando GST
es IVA
0
(Posición fija)
0
Habilitar la impresión de impuestos*
Inhabilitarla
0
1
F
Impresión de exención de GST en
informes X/Z
Habilitar la impresión de exención de GST*
Inhabilitarla
0
1
G y H
Sistema de cálculo de impuestos
Impuestos automáticos*
00
Impuestos canadienses (número del tipo de impuestos)
01 a 11
Sistema de cálculo de impuestos
• Para el sistema de impuestos de EE.UU., seleccione “auto-tax” (impuestos automáticos).
Programación 2 de selección de diversas funciones
4
Modo de ahorro de energía
*ABCD
s 10 @
s A
Registro:
* Elemento:
Selección:
A
Entrar en el modo de ahorro de energía
cuando se visualice la hora
Sí (ajuste inicial)
No
0
1
B a D
Tiempo (mín.) para entrar en el modo de ahorro de
energía desde que se efectuó la última operación
001-254 ó 999
(Ajuste inicial: 030)
Cuando se ajusta 999 para B a D, se inhabilita el establecimiento en el modo de ahorro de
energía.
26
Formato de impresión del mensaje del membrete
Podrá seleccionar el número de líneas del mensaje del membrete, y la posición en la que se imprime en el
recibo o registro diario.
Para ajustar “0”
*A
s 11 @
s A
*A: Tipo de mensaje del membrete
0: Mensaje de 3 líneas de encabezamiento sin membrete gráfico
1: Sólo membrete gráfico
2: Mensaje de 3 líneas de pie de recibo con membrete gráfico
3: Mensaje de 6 líneas de encabezamiento
4: Mensaje de 3 líneas de encabezamiento con membrete gráfico
5: Mensaje de 3 líneas de encabezamiento y mensaje de 3 líneas de pie de recibo
Interfaz RS-232C
(1) Número de terminal RS-232C
Para ajustar “0”
Número de terminal
(máx. 6 dígitos)
s 30 @
s A
(2) Forma de transmisión RS-232C
Para ajustar “0”
*A
s 31 @
s A
Registro:
* Elemento:
Selección:
A
Forma de la línea de transmisión
Sistema semidúplex
1
0
Sistema dúplex*
(3) Velocidad de transmisión RS-232C
*AB
s 32 @
s A
Registro:
* Elemento:
Selección:
A
B
Introduzca siempre 0.
Velocidad de transmisión (bps)
0
3
4
5
6
2400
4800
9600*
19200
(4) Código de inicio y código de fin de RS-232C
Para ajustar “000000”
*ABCDEF
s 33 @
s A
* A-C: Código inicial 000-127
D-F: Código final 000-127
27
(5) Ajuste de tiempo vencido de RS-232C
Tiempo vencido
(1 a 255 seg.)
s 35 @
s A
s A
Densidad de impresora térmica
Para ajustar “0”
*Densidad de
s 50 @
impresora (00-99)
* En el ajuste inicial se ajusta 50. Para oscurecer la impresión, ajuste un número mayor, y para que sea más
clara, ajuste un número menor.
Selección del idioma
Para ajustar “0”
*Idioma
s 88 @
2: Francés
(0, 2 ó 3)
A
*Idioma: 0: Inglés
3: Español
Cuando cambie el idioma, el texto como el de sección/PLU, nombre de dependientes, mensaje de
membrete y de texto de funciones, que usted haya programado, se repondrá a los ajustes iniciales.
Especificación de dependientes de instrucción para el modo de instrucción
Para los detalles sobre la instrucción de dependientes, consulte el “MODO DE INSTRUCCION” en la página 29.
Para cancelar
Código de dependiente
(1 a 15)
s 86 @
s A
Programación de la tecla AUTO — Tecla de secuencia automática —
Si se programan transacciones que se realizan con frecuencia o secuencias de informes para la tecla a,
puede llamar esas transacciones y/o informes pulsando simplemente la tecla a en las operaciones de teclas.
Borrar
Transacción
a
a A
máx. 25 veces
Programación para a; registro de un artículo de PLU 2 (precio unitario programado: 1,50) y de un artículo de
la sección 6 (precio unitario: 1,00)
Ejemplo de operación de teclas
a
+
a
A
Ajuste
AUTO
2
100
p
28
Lectura de programas almacenados
5
La máquina le permitirá leer todos los programas almacenados en el modo PGM.
Secuencia de las teclas para la lectura de programas almacenados
Nombre del informe
Secuencia de teclas
Informe de programación 1
A
Informe de programación 2
2
1
3
A
A
A
Informe de programación de tecla automática
Informe de programación de densidad de impresora
Informe de programación de PLU
Código inicial de PLU
@
Código final de PLU
p
Para detener la lectura del informe de programación de PLU, gire el selector de modo a la posición
MGR.
MODO DE INSTRUCCION
El modo de instrucción se utiliza cuando el operador o el administrador practica las operaciones de la caja
registradora.
Cuando se selecciona un dependiente que está en instrucción, la máquina se establece automáticamente en el
modo de instrucción. Para especificar un dependiente que deba recibir instrucción, consulte el apartado de
“Especificación de dependientes de instrucción para el modo de instrucción” en “PROGRAMACION
La operación de instrucción sólo es válida en el modo REG, MGR y VOID.
La memoria del dependiente correspondiente sólo se actualiza en el modo de instrucción.
LECTURA (X) Y REPOSICION (Z) DE
LOS TOTALES DE VENTAS
• Utilice la función de lectura (X) cuando necesite leer la información de ventas registrada desde la última
reposición. Puede obtener esta lectura todas las veces que quiera dado que no afecta a la memoria de la
registradora.
• Utilice la función de reposición (Z) cuando necesite borrar la memoria de la registradora. La reposición
imprime toda la información de ventas y borra toda la memoria excepto para GT1 a GT3, GT de modo de
instrucción, cuenta de reposición y número consecutivo.
Resumen de informes de lectura (X) y reposición (Z)
1
Informes X1 y Z1: Informes de ventas diarias
Informes X2 y Z2: Informes de consolidación periódica (mensual)
Para hacer un informe X o Z, gire el selector de modo a la posición apropiada consultando la columna de
“Posición del selector de modo” mostrada en la tabla de la página siguiente, y emplee la siguiente secuencia de
teclas correspondiente.
29
Posición del selector de modo
Elemento
Operación de teclas
: Importe total de sección
OPX/Z X1/Z1 X2/Z2
Código de sección
d
Informe rápido:
Sólo visualización)
( !a <)
Tecla de sección
Para las secciones 1 a 16; Tecla de sección
(
Para borrar la
visualización,
pulse la tecla
( !a <)
Para las secciones 17 a 32; D
X
--
--
o
l
gire el selector de
modo a otra
posición.
Tecla
: Importe de metálico en el cajón
@
Tecla A: Total de ventas
Informe de ventas
completo
Lectura:
Reposición: P
Reposición: P
-- X1, Z1 X2, Z2
A
A
L
Informe de
dependiente
individual
Lectura:
L
X, Z
--
--
(El informe del dependiente actual)
Informe de todos
los dependientes
Lectura:
Reposición: P
-- X1, Z1 --
-- X1, Z1 --
-- X1, Z1 --
L
L
Todas las PLU
Código de
Código de
PLU final
Lectura:
@
p
PLU inicial
Informe de ventas
de PLU
Reposición:
Código de
Todas las PLU
Código de
PLU final
@
P p
s
PLU inicial
Informe horario
Lectura:
s
Reposición: P
• Cuando las cantidades de ventas y los importes de ventas son cero, se pasa por alto la
impresión. Si no desea que se pase por alto, cambie la programación. (Consulte el apartado de
• “X” representa el símbolo de lectura y “Z” representa el símbolo de reposición en los informes.
• Para dejar de leer y reponer el informe de ventas de PLU, gire el selector de modo a la posición
MGR. Los datos no se borrarán al efectuar la reposición.
LECTURA Y REPOSICION DE INFORMES EJ
La caja registradora está provista de la función de registro diario electrónico (EJ). Esta función sirve para
registrar los datos del registro diario en una memoria en lugar de hacerlo en el papel de registro diario, y para
imprimir los datos como un informe EJ. La caja registradora registra los datos de registro diario en los modos
REG, PGM, VOID, X1/Z1 y X2/Z2. En el ajuste inicial, se pueden almacenar un máximo de 1.000 líneas en la
memoria, y usted podrá ampliarla hasta 2.000 líneas. Para los detalles sobre la programación de EJ, consulte la
Impresión de los datos del registro diario en forma de una transacción
Podrá imprimir los datos del registro diario de una transacción actual registrada en la memoria EJ pulsando la
tecla
durante la transacción.
R
Esta función es válida cuando el estilo de impresión se ajusta al tipo de recibos en la
programación, y también la función de activación/desactivación (ON/OFF) de recibo se ajusta a
OFF (desactivación).
30
Lectura y reposición de los datos del registro diario electrónico (emisión
de informe EJ)
Podrá leer los datos del registro diario almacenados en la memoria EJ en el formato del registro diario
ejecutando el procedimiento siguiente en el modo X1/Z1 u OP X/Z.
Para leer todos los datos:
Para reponer todos los datos:
7: @ A
Para leer los 10 registros últimos:
7: P @ A
710 @ A
• Para dejar de leer o reponer los datos, gire el selector de modo a la posición “MGR”. Los datos no
se borrarán al efectuar la reposición.
REGISTROS DE ANULACION
El límite programado para las funciones (tales como importes máximos) puede anularse haciendo un registro de
anulación en el modo MGR.
1. Gire el selector de modo a la posición MGR.
2. Haga el registro de anulación.
CORRECCION DESPUES DE FINALIZAR UNA
TRANSACCION (Modo de cancelación)
Cuando necesite cancelar los registros incorrectos que los dependientes no pueden corregir (registros
incorrectos que se encuentran después de finalizar una transacción o que no pueden corregirse mediante
cancelación directa o indirecta), siga este procedimiento:
1. Gire el selector de modo a la posición VOID empleando la llave del administrador (MA) para establecer la
máquina en el modo de cancelación.
2. Repita los registros anotados en el recibo incorrecto. (Todos los datos del recibo incorrecto se suprimirán de
la memoria de la registradora y los importes cancelados se añadirán al totalizador de transacción del modo
de cancelación.)
MANTENIMIENTO PARA EL OPERADOR
En caso de corte de la alimentación
1
Si se corta la alimentación, la registradora retiene el contenido de su memoria y toda la información sobre las
entradas de ventas.
• Cuando el corte de la alimentación ocurre en el estado libre de la registradora o cuando está realizando una
entrada, la máquina retorna al funcionamiento normal después de recuperarse la alimentación.
• Cuando el corte de la alimentación ocurre durante un ciclo de impresión, la registradora imprime “========”
y lleva a cabo después el procedimiento de impresión correcto después de recuperarse la alimentación.
31
En el caso de error de impresora
2
Si se termina el papel de la impresora, se parará la impresora, y aparecerá “PPPPPPPPPP” en el visualizador.
No pueden aceptarse los registros de teclas. Instale el rollo de papel nuevo, y luego pulse la tecla
Si se levanta el cabezal de impresión, se parará la impresora y aparecerá “H” en el extremo izquierdo del
visualizador. No pueden aceptarse los registros de teclas. Vuelva a colocar el cabezal de impresión en la
.
l
posición correcta, y entonces pulse la tecla
.
l
Precauciones al manejar la impresora
3
• Evite los lugares polvorientos y húmedos, la luz directa del sol y el polvo
metálico (en esta máquina se emplean un imán permanente y un
electroimán.)
• Utilice la palanca de liberación del cabezal de impresión sólo cuando sea
necesario.
• No tire nunca del papel cuando esté en contacto con el cabezal de
impresión. Suelte primero el cabezal con la palanca de liberación del cabezal
de impresión y luego quite el papel.
• No toque nunca la superficie del cabezal de impresión.
• No toque nunca el cabezal de impresión ni el motor durante la impresión ni
antes de que se hayan enfriado.
Reemplazo de las pilas
4
Esta caja registradora muestra un símbolo de pilas gastadas ( ) cuando las pilas están casi gastadas, y
visualiza un símbolo de que no hay pilas ( ) cuando las pilas están demasiado gastadas o cuando no se han
instalado las pilas.
Cuando se visualice el símbolo de pilas gastadas, reemplace las pilas por otras nuevas lo antes posible. Las
pilas existentes se gastarán por completo en unos dos días.
Cuando se visualice el símbolo de que no hay pilas, reemplace inmediatamente las pilas. De lo contrario, si se
desenchufa el cable de alimentación de CA o si ocurre un corte de la corriente, todos los ajustes programados
se repondrán a los ajustes de fábrica y se borrarán los datos almacenados en la memoria.
Asegúrese de observar las precauciones indicadas en la página 1 sobre la manipulación de las
pilas.
Para reemplazar las pilas:
1. Asegúrese de que la caja registradora está enchufada.
2. Gire el selector de modo a la posición REG.
3. Extraiga la cubierta de la impresora.
4. Abra la cubierta del compartimiento de las pilas que se encuentra al lado del soporte del rollo de papel y
extraiga las pilas gastadas.
5. Instale tres pilas nuevas del tamaño “AA” en el compartimiento de las pilas. Asegúrese de que las
polaridades positiva y negativa de cada pila estén encaradas en la dirección adecuada.
Cuando las pilas estén correctamente instaladas, desaparecerá el símbolo “ ” o “ ”.
6. Cierre la cubierta del compartimiento de las pilas.
7. Vuelva a colocar la cubierta de la impresora.
32
Reemplazo del rollo de papel
5
Utilice siempre rollos de papel especificados por SHARP.
Si usa otros rollos de papel que no sean los especificados, pueden originarse atascos de papel y funcionar mal
la registradora.
(Forma de colocar el rollo de papel)
(Forma de cortar el extremo del papel)
A la impresora
A la impresora
Correcto
Incorrecto
Correcto
Incorrecto
Extracción del rollo de papel
Cuando aparezca tinta de color rojo en el rollo de papel, será indicación de que tiene que cambiarlo. Sustituya
el rollo de papel por uno nuevo. Si no piensa utilizar la registradora durante mucho tiempo, extraiga el rollo de
papel y guárdelo en el lugar apropiado.
Precaución: El cortador de papel está montado en la cubierta. Tenga cuidado para no cortarse.
Cuando no emplee el carrete de toma:
1. Extraiga la cubierta de la impresora.
2. Corte el papel detrás de la impresora y cerca del rollo de papel.
3. Pulse la tecla
hasta que el papel que queda en la impresora salga por completo.
4. Extraiga el rollo de papel del soporte del rollo de papel.
F
No tire del papel por la impresora.
Cuando emplee el carrete de toma:
1. Extraiga la cubierta de la impresora.
2. Pulse la tecla
para hacer avanzar el papel de registro diario hasta que la parte impresa salga del paso.
3. Corte el papel y extraiga el carrete de toma.
F
4. Corte el papel detrás la impresora y cerca del rollo de papel.
5. Pulse la tecla
hasta que el papel que queda en la impresora salga por completo.
F
6. Extraiga el rollo de papel del soporte del rollo de papel.
7. Extraiga el lado exterior del carrete de toma.
8. Extraiga el rollo de registro diario impreso del carrete de toma.
Instalación del rollo de papel
1. Gire el selector de modo a la posición REG con el cable de CA enchufado.
2. Extraiga la cubierta de la impresora.
3. Compruebe que la palanca de liberación del cabezal de impresión esté en su posición de impresión.
4. Coloque correctamente el papel en el soporte del rollo de papel.
5. Inserte el extremo del papel en la impresora hasta que entre en el dispositivo de alimentación automática de
la impresora y salga de la impresora por la parte superior.
Si la impresora no engancha el papel, haga avanzar el papel mientras pulsa la tecla
.
F
6. Cuando no emplee el carrete de toma (cuando se usa como papel de recibos):
• Corte el papel sobrante que sale de la impresora empleando el borde de la cubierta interior, y vuelva a
colocar la cubierta de la impresora. Pulse la tecla
de la impresora.
para asegurarse de que el papel sale por la cubierta
F
Si no sale el papel, abra de nuevo la cubierta de la impresora y haga pasar el extremo del
papel entre el cortador manual y la guía de papel de la impresora, y luego vuelva a cerrar la
cubierta.
33
Cuando emplee el carrete de toma (cuando se usa como papel de registro diario):
• Inserte el extremo del papel en la ranura del carrete. (Pulse la tecla
necesario.)
para alimentar más papel si es
F
• Bobine el papel dos o tres vueltas en torno al eje del carrete.
• Ajuste el carrete en el rodamiento, y pulse la tecla
para sacar la flojedad excesiva del papel.
F
• Vuelva a colocar la cubierta de la impresora.
Extracción del papel atascado
6
Precaución: El cortador de papel está montado en la cubierta. Tenga cuidado para no cortarse. No
toque nunca el cabezal de impresión inmediatamente después de imprimir, porque éste
estará aún caliente.
1. Extraiga la cubierta de la impresora.
2. Tire de la palanca de liberación del cabezal de impresión hacia usted (a la posición de cabezal levantado).
3. Extraiga el papel atascado. Compruebe si quedan restos de papel en la impresora y, si los hubiera, quítelos.
4. Vuelva a poner la palanca de liberación del cabezal de impresión a su posición original.
5. Ponga correctamente el rollo de papel siguiendo los pasos mencionados en “Instalación del rollo de papel”.
Limpieza del cabezal de impresión
7
Cuando el texto impreso se oscurece o aparece borroso, el polvo del papel
puede pegarse en el cabezal de impresión. Limpie el cabezal de impresión de
la forma siguiente:
Rodillo
Cabezal de
impresión
Precaución:
• No toque nunca el cabezal de impresión con una herramienta ni nada
que sea duro porque podría estropear el cabezal.
• El cortador de papel está montado en la cubierta. Tenga cuidado para
no cortarse.
1. Gire el selector de modo a la posición OFF.
2. Extraiga la cubierta de la impresora.
3. Extraiga la cubierta interior que protege la impresora. (Pulse la palanca
situada a ambos lados y levante la cubierta.)
4. Tire de la palanca de liberación del cabezal de impresión hacia usted (a la posición de cabezal levantado).
5. Limpie el cabezal de impresión con un palillo de algodón o un paño blando humedecido en alcohol etílico o
alcohol isopropílico.
6. Vuelva a colocar la palanca de liberación del cabezal de impresión a su posición original inmediatamente
después de terminar la limpieza.
7. Vuelva a colocar la cubierta interior. (Inserte las lengüetas laterales de la cubierta en sus ranuras y presione
la cubierta en la impresora hasta que quede correctamente asentada.)
8. Ponga correctamente el rollo de papel siguiendo los pasos mencionados en “Instalación del rollo de papel”.
34
Extracción del cajón
8
El cajón de la caja registradora es extraíble. Después de terminar la jornada
laboral, extraiga el cajón. Para extraer el cajón, tire del mismo
completamente hacia delante y extráigalo levantándolo. La caja de monedas
de 5 denominaciones también es extraíble.
Caja de
monedas
Abertura manual del cajón
9
El cajón se abre automáticamente. Sin embargo, cuando haya un fallo o corte
de la corriente o la registradora quede fuera de servicio, deslice la palanca
situada en la parte inferior de la registradora en la dirección de la flecha. (Vea
la figura a la izquierda.)
El cajón no se abrirá, sin embargo, si está cerrado con la llave de la cerradura
del cajón.
Palanca
Antes de solicitar el servicio de un técnico
10
Los casos de mal funcionamiento de la columna de la izquierda de la tabla siguiente, indicados bajo el título
“Fallo”, no son necesariamente averías de la registradora. Se recomienda pues consultar la sección
“Comprobación” de la columna de la derecha antes de llamar al servicio técnico.
Fallo
Comprobación
(1) El visualizador muestra los símbolos que no
• ¿Se ha inicializado correctamente la máquina como se
muestra en “PARA EMPEZAR”?
tienen ningún sentido.
(Tenga presente que la inicialización borra todos los datos y
ajustes programados que están almacenados en la memoria.)
(2) El visualizador no se ilumina aunque el selector
de modo esté colocado en cualquier otra
posición que no sea “OFF”.
• ¿Se suministra alimentación en la toma de corriente?
• ¿Está la clavija del cable de alimentación desenchufada o
mal conectada a la toma de corriente?
(3) El visualizador se ilumina, pero la registradora
no responde a los registros.
• ¿Está el código del dependiente asignado a la registradora?
• ¿Está el selector de modo bien colocado en la posición “REG”?
(4) No se emiten recibos.
• ¿Está el rollo de papel bien instalado?
• ¿Hay algún atasco de papel?
• ¿Está la función de recibos en el estado “OFF”?
• ¿Está la palanca de liberación del cabezal de impresión en la
posición de impresión?
(5) No sale el papel del registro diario.
• ¿Está el carrete de toma bien instalado en el rodamiento?
• ¿Hay algún atasco de papel?
• ¿Se ha seleccionado la impresión del registro diario en la
programación del estilo de impresión? (Si se ha seleccionado la
impresión de recibos, el papel no se bobinará en torno al carrete
de toma.)
(6) La impresión no es normal.
• ¿Está la palanca de liberación del cabezal de impresión en la
posición de impresión?
• ¿Está el rollo de papel correctamente instalado?
35
Tabla de códigos de error
Cuando se visualicen los siguientes códigos de error, pulse la tecla
y tome la acción apropiada de acuerdo
l
con la tabla siguiente.
Código
de error
Estado de error
Acción
E01
E02
E03
E07
E11
Error de registro
Haga el registro con las teclas correctas.
Haga el registro con las teclas correctas.
Introduzca un código correcto.
Error de operación incorrecta
Se ha introducido un código no definido.
La memoria está llena (en la programación de la tecla
). Programe la tecla
con 25 pasos.
a
a
Pulsación obligatoria de la tecla
directa
para finalización
Pulse la tecla
y prosiga la operación.
s
s
E12
E32
E34
E35
E36
E37
E67
Importe recibido obligatorio
Efectúe una operación de importe recibido.
Efectúe un registro de código de dependiente.
Haga el registro dentro del límite de registro.
Haga un registro de precio preajustado.
Haga un registro de precio abierto.
Falta el registro de un código de dependiente.
Error de límite de rebose
La entrada de precio abierto está inhibida.
La entrada de precio preajustado está inhibida.
La finalización directa está inhibida.
Haga una operación de importe recibido.
No se permite la cancelación del subtotal.
Finalice la transacción y corrija las entradas erróneas
en el modo de cancelación.
Emplee estas etiquetas con las teclas de sección. Escriba los nombres de sección en las etiquetas y adhiéralas
a las teclas de sección sacando primero las cubiertas transparentes de las teclas. (Haga una copia de esta
página.)
Ejemplo:
17
Leche
Pan
1
E
18
22
26
30
20
24
28
32
2
1
6
5
10
14
13
4
3
8
7
12
11
16
15
D
I
N
S
B
G
L
Q
17
21
25
29
19
23
27
31
9
E
J
O
T
C
H
M
R
36
|