MODEL
BD-HP75U
BLU-RAY DISC/DVD PLAYER
OPERATION MANUAL
OPERATION MANUAL
ENGLISH
Introduction
SAFETY INFORMATION
CAUTION:
“WARNING–FCC Regulations state
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
USE OF CONTROLS OR ADJUSTMENTS OR
PERFORMANCE OF PROCEDURES OTHER THAN
THOSE SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.
that any unauthorized changes or
modifications to this equipment not
expressly approved by the manufacturer
could void the user’s authority to operate
this equipment.”
CAUTION:
TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER. NO
USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
AS THE LASER BEAM USED IN THIS UNIT IS
HARMFUL TO THE EYES, DO NOT ATTEMPT TO
DISASSEMBLE THE CABINET.
REFER SERVICING TO QUALIFIED PERSONNEL
ONLY.
INFORMATION
This equipment has been tested and found
to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment generates,
uses and can radiate radio frequency energy
and, if not installed and used in accordance with
the instructions, may cause harmful interference
to radio communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning
the equipment off and on, the user is encouraged
to try to correct the interference by one or more
of the following measures:
This symbol warns the user of
uninsulated voltage within the unit
that can cause dangerous electric
shocks.
• This Player is classified as a CLASS 1 LASER
product.
• The CLASS 1 LASER PRODUCT label is located
on the rear cover.
• This product contains a low power laser device. To
ensure continued safety do not remove any cover
or attempt to gain access to the inside of the
product. Refer all servicing to qualified personnel.
This symbol alerts the user that
there are important operating and
maintenance instructions in the
literature accompanying this unit.
WARNING:
TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
–Reorient or relocate the receiving antenna.
–Increase the separation between the equipment
and receiver.
–Connect the equipment into an outlet on a
circuit different from that to which the receiver is
connected.
–Consult the dealer or an experienced radio/TV
technician for help.
1
SAFETY INFORMATION
FCC Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Wireless Radio
For product available in the USA/Canada market, only channel 1–11 can be operated. Selection of other channels is not possible.
This device is going to be operated in 2.400–2.483GHz frequency range, it is restricted in indoor environment only.
Important: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
IMPORTANT SAFETY INSTRUCTIONS
Electricity is used to perform many useful functions, but it can also cause personal
injuries and property damage if improperly handled. This product has been engineered
and manufactured with the highest priority on safety. However, improper use can result
in electric shock and/or fire. In order to prevent potential danger, please observe the
following instructions when installing, operating and cleaning the product. To ensure
your safety and prolong the service life of your Blu-ray Disc/DVD Player, please read the
following precautions carefully before using the product.
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
11) Only use attachments/accessories specified by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when unused for long periods of
time.
14) Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as power-
supply cord or plug is damaged, liquid has been spilled or objects have
fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
Additional Safety Information
15) Power Sources—This product should be operated only from the type of power
source indicated on the marking label. If you are not sure of the type of power
supply to your home, consult your product dealer or local power company. For
products intended to operate from battery power, or other sources, refer to the
operating instructions.
16) Overloading—Do not overload wall outlets, extension cords, or integral convenience
receptacles as this can result in a risk of fire or electric shock.
17) Object and Liquid Entry—Never push objects of any kind into this product through
openings as they may touch dangerous voltage points or short-out parts that could
result in a fire or electric shock. Never spill liquid of any kind on the product.
7) Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or
other apparatus (including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide blade or the third prong are
provided for your safety. If the provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
2
IMPORTANT SAFETY INSTRUCTIONS
18) Damage Requiring Service—Unplug this product from the wall outlet and refer
servicing to qualified service personnel under the following conditions:
a) When the AC cord or plug is damaged,
19) Replacement Parts—When replacement parts are required, be sure the service
technician has used replacement parts specified by the manufacturer or have the
same characteristics as the original part. Unauthorized substitutions may result in
fire, electric shock, or other hazards.
b) If liquid has been spilled, or objects have fallen into the product,
c) If the product has been exposed to rain or water,
d) If the product does not operate normally by following the operating
instructions.
20) Safety Check—Upon completion of any service or repairs to this product, ask the
service technician to perform safety checks to determine that the product is in
proper operating condition.
Adjust only those controls that are covered by the operating instructions as
an improper adjustment of other controls may result in damage and will often
require extensive work by a qualified technician to restore the product to its
normal operation,
21) The main AC plug is used as disconnect device and shall always remain readily
operable.
e) If the product has been dropped or damaged in any way, and
f) When the product exhibits a distinct change in performance - this indicates a
need for service.
• Water and Moisture—Do not use this product near
water - for example, near a bath tub, wash bowl,
kitchen sink, or laundry tub; in a wet basement; or
near a swimming pool; and the like.
• Heat—The product should be situated away from
heat sources such as radiators, heat registers, stoves,
or other products (including amplifiers) that produce
heat.
• Stand—Do not place the product on an unstable
cart, stand, tripod or table. Placing the product on an
unstable base can cause the product to fall, resulting
in serious personal injuries as well as damage to the
product. Use only a cart, stand, tripod, bracket or
table recommended by the manufacturer or sold with
the product. When mounting the product on a wall,
be sure to follow the manufacturer’s instructions. Use
only the mounting hardware recommended by the
manufacturer.
• Lightning—For added protection for this product
during a lightning storm, or when it is left unattended
and unused for long periods of time, unplug it from
the wall outlet. This will prevent damage to the
product due to lightning and power-line surges.
• To prevent fire, never place any type of candle or
flames on the top or near the product.
• To prevent fire or shock hazard, do not expose this
product to dripping or splashing.
No objects filled with liquids, such as vases, should
be placed on the product.
• Selecting the location—Select a place with no direct
sunlight and good ventilation.
• To prevent fire or shock hazard, do not place the AC
cord under the product or other heavy items.
• Ventilation—The vents and other openings in the
cabinet are designed for ventilation. Do not cover
or block these vents and openings since insufficient
ventilation can cause overheating and/or shorten the
life of the product. Do not place the product on a bed,
sofa, rug or other similar surface, since they can block
ventilation openings. This product is not designed
for built-in installation; do not place the product in an
enclosed place such as a bookcase or rack, unless
proper ventilation is provided or the manufacturer’s
instructions are followed.
3
PRECAUTIONS
Precautions on viewing stereoscopic 3D images
Notes on using Wireless LAN
• Do not view stereoscopic 3D images if you have a history of photosensitivity, heart
disease or poor health. This may cause the symptoms to worsen.
• If you experience any health problems such as fatigue and discomfort while viewing
stereoscopic 3D images, immediately discontinue viewing. Continuing viewing after
symptoms appear may cause health risks. Take a break until the symptoms have
completely disappeared.
• When this player is connected to a wireless LAN network, transmissions between the
wireless LAN adapter (supplied) and a wireless LAN compatible broadband router
(commercially available) are carried out.
Precautions on using Wireless LAN
• The following devices, radio stations, etc. use the same frequency bands. Do not use
wireless LAN near them.
• Ages of 5–6 or over are recommended for viewing stereoscopic 3D images.
Symptoms such as fatigue and discomfort are difficult to determine in young
children, therefore they may suddenly become ill. When viewing 3D images with
children, please watch for eye strain symptoms.
• When viewing stereoscopic 3D images, take a moderate break after watching one
title. Viewing for extended periods may cause visual strain.
Manufacturing/scientific/diagnostic equipment such as pacemakers, etc.
Specified low power radio stations (radio stations that do not require a license)
If this player is used near these devices, there is a possibility that radio wave
interference may occur. Therefore transmission may not be possible or speed may be
reduced.
• Mobile phones, radios, etc. use different radio frequency bands from wireless LAN,
so there will not be any effect on the transmissions of these devices or wireless LAN
if this player is used near them.
However, if a wireless LAN product is placed near one of these devices, audio or
video noise may occur due to the electromagnetic waves that emit from wireless LAN
products.
• Radio waves will pass through the wood, glass, etc. used in standard housing,
however they will not pass through reinforcing bars, metal, concrete, etc. Radio
waves will not pass through walls and floors if these materials are used.
Precautions when cleaning this product
• Turn off the main power and unplug the AC cord from the wall outlet before handling.
• To clean the outer cabinet, periodically wipe it with a soft cloth (cotton, flannel, etc.).
• For severe dirt, soak a soft cloth (cotton, flannel, etc.) in some neutral detergent
diluted with water, wring the cloth out thoroughly, wipe off the dirt, then wipe again
with a soft, dry cloth.
• Do not use chemicals or a chemically treated cloth for cleaning. It may damage the
cabinet finish.
4
DEAR SHARP CUSTOMER
Thank you for your purchase of the SHARP Blu-ray Disc/DVD Player. To ensure safety and many years of trouble-free operation of your product, please read
the Important Safety Instructions carefully before using this product.
Getting Started
Step 1: Unpacking
Step 2: Selecting equipment to connect
Make sure the following accessories are provided with the product.
Connection varies with the equipment used. Refer to Connection
(Pages 16–19).
Turn off the devices before connecting.
Remote control unit
AC cord
Enjoying BD-LIVE and video on demand services (e-Contents)
To enjoy BD-LIVE content or video on demand streaming content on your TV,
after an Internet connection is made, communication setup is required. Refer
to “Communication Setup” (Pages 46–49).
Step 3: Playing back video/picture/music content
Play back video, picture or music content from the desired media source
such as Blu-ray and DVD discs, or via the Internet.
Refer to Playback (Pages 20–39) and video on demand streaming content
(Pages 55–56).
Page 20
Step 4: Adjust settings to suit your preference
Adjust settings to enjoy various features and other functions for playing
discs/content.
Refer to Settings (Pages 40–54).
Wireless LAN adapter
Pages 15 and 20
“AAA” size battery (g2)
Page 19
Page 20
5
Contents
Operating a SHARP TV Using the Remote Control.................................................... 22
TV function control................................................................................................. 22
Turning Off the LCD Backlight and Indications .......................................................... 22
Using AQUOS LINK.................................................................................................... 23
Controlling the Blu-ray disc player using AQUOS LINK ........................................ 23
Using 3D..................................................................................................................... 23
Control Panel.............................................................................................................. 24
Video/Picture/Music Playback.........................................................................25
Loading a Disc............................................................................................................ 25
BD/DVD Video Playback............................................................................................. 25
Displaying the disc information.............................................................................. 26
BD/DVD Menus .......................................................................................................... 26
Start playback by selecting a title from the top menu ........................................... 26
Using the disc menu .............................................................................................. 26
Using the pop-up menu......................................................................................... 27
Enjoying BONUSVIEW or BD-LIVE............................................................................. 27
Use of Picture in Picture function (secondary audio/video playback) ................... 28
Virtual Package ...................................................................................................... 28
BD-LIVE ................................................................................................................. 28
DVD-R/-RW (VR format) / BD-RE/-R (BDAV format) Playback................................... 29
Playback by selecting a title .................................................................................. 29
Playback by selecting a chapter............................................................................ 30
Sorting the titles..................................................................................................... 30
Playback by selecting a Playlist............................................................................. 30
Playback from the beginning or resume playback................................................. 30
Audio CD Playback..................................................................................................... 31
Playback from the beginning ................................................................................. 31
Playback by selecting a track ................................................................................ 31
Operation procedure for the “Functions” menu..................................................... 31
Audio Data (MP3 File) Playback ................................................................................. 32
Displaying Still Images (JPEG files)............................................................................ 33
Accessing DLNA servers............................................................................................ 34
Playback by selecting a file list.............................................................................. 34
Playback Functions...........................................................................................35
Fast Forward/Reverse (Search) .................................................................................. 35
Skipping to the Next or the Start of the Current Chapter (Track/Title) ....................... 35
Pause/Frame Advance Playback................................................................................ 35
Slow Playback (Forward/Reverse).............................................................................. 35
Skip Search ................................................................................................................ 36
Replay......................................................................................................................... 36
Repeat Playback of a Title or Chapter (Repeat Playback) ......................................... 36
Partial Repeat Playback (Repeat Playback of a Specified Part)................................. 36
Displaying the Audio Information ............................................................................... 37
Switching Subtitles..................................................................................................... 37
Switching the Angle.................................................................................................... 37
Displaying the Angle Mark.......................................................................................... 37
Settings During Playback .................................................................................38
Function Control......................................................................................................... 38
Function control operation procedure ................................................................... 38
Functions which can be set ................................................................................... 39
Introduction
SAFETY INFORMATION ......................................................................................1
IMPORTANT SAFETY INSTRUCTIONS..............................................................2
PRECAUTIONS ....................................................................................................4
DEAR SHARP CUSTOMER .................................................................................5
Getting Started ....................................................................................................5
Contents...............................................................................................................6
What would you like to do with this Player?.....................................................8
About Media Types..............................................................................................9
Blu-ray Disc.................................................................................................................. 9
Types of Discs/Media Formats that Can Be Used with This Player ............................. 9
Discs that Cannot Be Used with This Player.............................................................. 10
About Disc Contents .................................................................................................. 11
BD Video ................................................................................................................ 11
Title, Chapter and Track......................................................................................... 11
Icons Used on BD/DVD Video Disc Cases ............................................................ 12
The Icons Used in This Operation Manual ................................................................. 12
Important Information.......................................................................................13
Disc Precautions......................................................................................................... 13
License and Copyright ............................................................................................... 13
Major Components............................................................................................14
Main Unit (Front)......................................................................................................... 14
Main Unit (Rear).......................................................................................................... 14
Remote Control Unit................................................................................................... 15
Keylock function......................................................................................................... 15
Connection
Connecting to a TV/projector...........................................................................16
Connecting to an amplifier/AV receiver ..........................................................17
HDMI connection........................................................................................................ 17
Digital audio connection............................................................................................. 17
Broadband Internet Connection ......................................................................18
Wired connection (LAN cable).................................................................................... 18
Wireless connection (wireless LAN)............................................................................ 19
Playback
Before Starting Playback..................................................................................20
Loading the Batteries in the Remote Control............................................................. 20
Approximate operating range of remote control.................................................... 20
Connecting the Power Cord....................................................................................... 20
Turning the Power On................................................................................................. 21
Turning the power on ............................................................................................. 21
Entering standby.................................................................................................... 21
Indicators on the Player ......................................................................................... 21
About the Home screen......................................................................................... 21
Language Setting ....................................................................................................... 22
Changing the on-screen display language ............................................................ 22
6
Contents
Settings
What to do first:
SETTINGS...........................................................................................................40
Common operations................................................................................................... 40
Basic Operation for Playback Setting ........................................................................ 41
Audio Video Settings .................................................................................................. 42
Smart Settings............................................................................................................ 43
AQUOS LINK.............................................................................................................. 43
Playback Setting......................................................................................................... 44
On Screen Language.................................................................................................. 45
Version........................................................................................................................ 45
System........................................................................................................................ 45
Communication Setup................................................................................................ 46
Sets whether “Cable” or “Wireless” is used for the network connection .............. 46
When selecting Cable ............................................................................................ 46
When selecting Wireless........................................................................................ 47
The operation procedure for inputting characters manually.................................. 49
USB Memory Management........................................................................................ 50
Software Update Settings .......................................................................................... 51
Auto Update from Network.................................................................................... 51
Manual Update from Network................................................................................ 52
Manual Update from USB memory device ............................................................ 52
Refer to “Getting Started” (p. 5) to prepare for using this
player.
Introduction (pp. 1–15)
Explains the important operation information.
Connection (pp. 16–19)
Shows the connecting options provided by this Player.
Playback (pp. 20–39)
Shows simple playback and useful functions.
Streaming content
Playing back video on demand streaming content........................................55
Instantly Watching Movies from Netflix...................................................................... 55
Playing back YouTube content ................................................................................... 55
Enjoying Movies and Internet Application with VUDU ............................................... 56
Settings (pp. 40–54)
Gives you more options to suit your circumstances.
Appendix
PC control of the Player....................................................................................57
Communication conditions for IP............................................................................... 57
IP Control Setup ......................................................................................................... 57
Communication conditions for RS-232C ................................................................... 57
Communication procedure......................................................................................... 57
Command list ............................................................................................................. 58
Troubleshooting.................................................................................................59
To Reset this Player................................................................................................ 62
On-screen Error Messages ..............................................................................63
Specifications ....................................................................................................64
Glossary .............................................................................................................66
Network Service Disclaimer.............................................................................69
About Software License....................................................................................70
LIMITED WARRANTY........................................................................................71
Streaming content (pp. 55–56)
Shows the Internet streaming services available with this
player.
Appendix (pp. 57–71)
Provides troubleshooting tips and more information.
The illustrations and on-screen displays in this operation manual
are for explanation purposes and may vary slightly from the
actual operations.
7
What would you like to do with this Player?
Watch high quality movies on Blu-ray discs
Enjoy BD-LIVE functions through the Internet
This Player is compatible with BD-LIVE. You can enjoy bonus content such
as movie trailers through the Internet when playing back BD-Video discs
compatible with BD-LIVE.
This Player offers full high-definition Blu-ray disc playback.
Video/Picture/Music Playback (p. 25)
Enjoying BONUSVIEW or BD-LIVE (pp. 27–28)
Enjoy stereoscopic and powerful 3D images
This player can play 3D content from 3D compatible Blu-ray discs through
an HDMI cable. To watch 3D images, connect a 3D compatible TV to this
player using an HDMI cable and play the 3D content while wearing 3D
glasses.
Access to videos, pictures and music from home network
servers
This player can play back video, picture and music data stored on your
home network servers such as a DLNA certified PC.
Using 3D (p. 23)
Accessing DLNA servers (p. 34)
Enjoy different kinds of media sources
Use this player to enjoy video, picture or music content from various types
of media sources such as DVDs, USB memory devices and via the Internet.
Enjoy video on demand streaming content with higher
image quality on your TV
This player supports video on demand streaming services using the
Internet. By connecting this player to the Internet, you can enjoy various
content streamed on your TV. Also, with this player’s “Super Picture”
function, you can enjoy video streaming images with higher image quality.
About Media Types (pp. 9–12)
Video/Picture/Music Playback (p. 25)
Playing back video on demand streaming content (pp. 55–56)
SUPER PICTURE (p. 43)
Simple connection and operation through HDMI
This Player is equipped with an HDMI terminal. You can connect it to the TV
using HDMI and no other cable will be needed to enjoy movies. If your TV is
compatible with AQUOS LINK, you can control both the TV and this Player
with simple operations.
Connecting to a TV/projector (p. 16)
8
About Media Types
Recording
Format
Disc
Size
Media Format
Recording Format
Contents
Blu-ray Disc
Disc Type
Contents
USB memory
device
DivX+HD
(H.264/MKV)
Audio + Video
(Movie)
Blu-ray Disc is the ultimate next generation optical
media format, offering the following key features:
• Largest capacity (25 GB single layer – 50 GB dual layer)
– with over 5 times the amount of content possible with
current DVDs, particularly well suited for high definition
feature films with extended levels of interactive features
• Pristine picture quality with the capability for full high
definition 1920 x 1080p resolution
• Best audio possible with uncompressed surround sound
(higher quality than even theater audio)
• Broadest industry support – ensuring more choice for
consumers in the marketplace
• Hardware products will be backward compatible with
DVDs, allowing continued enjoyment of existing DVD
libraries.
• Disc Durability – new breakthroughs in hard coating
technologies gives Blu-ray Discs the strongest
resistance to scratches and finger prints.
BD
Region
Video code A/ALL
—
Audio
+ Video
(Movie)
12 cm
(5”)
Still image
(JPEG file)
JPEGJ
Audio
MP3K
BD-RE DL
BD-R DL
BDMV/BDAV
format
• BD/DVD video players and discs have region codes,
which dictate the regions in which a disc can be played.
This Player’s region code is A for BD and 1 for DVD.
(Discs marked ALL will play in any player.)
• BD/DVD video operations and functions may be
different from the explanations in this manual and
some operations may be prohibited due to disc
manufacturer’s settings.
DVD Region
Video code
1/ALL
Video format
Audio
+ Video
(Movie)
12 cm
(5”)
8 cm
(3”)
ALL
1
DVD+RW/DVD+R
DVD-RW/DVD-R
Video/VR/
AVCHD
DVD+R DL/DVD-R format
Audio
+ Video
(Movie)
12 cm
(5”)
8 cm
(3”)
• If a menu screen or operating instructions are displayed
during playback of a disc, follow the operating
procedure displayed.
DL
(finalized disc
only)
NOTE
DivX+HD
(H.264/MKV)
Types of Discs/Media Formats that
Can Be Used with This Player
• Playback for some of the discs in the left side column
tables may not be possible depending on the disc.
• “Finalize” refers to a recorder processing a recorded
disc so that it will play in other DVD players/recorders
as well as this player. Only finalized DVD discs will play
back in this player. (This player does not have a function
to finalize discs.)
• Some discs cannot be played back depending on the
recording format.
• DivX playback may not be available depending on the
DivX content or file.
Still
JPEGJ
MP3K
• The following discs can be played back in this Player.
Do not use an 8 cm (3”) to 12 cm (5”) adapter.
• Use discs that conform to compatible standards as
indicated by the presence of official logos on the disc
label. Playback of discs not complying with these
standards is not guaranteed. In addition, the image
quality or sound quality is not guaranteed even if the
discs can be played back.
image
(JPEG
file)
Audio
Audio
Audio CD
(CD-DA)
12 cm
(5”)
8 cm
(3”)
Audio CDI
CD-RW/CD-R
Audio CD
(CD-DA)
Audio
Still
JPEGJ
MP3K
image
(JPEG
file)
Audio
9
About Media Types
*3 About the MP3 file format
The following CD-RW/R discs cannot be played.
• Discs on which data has not been recorded cannot be
played back.
• Discs recorded in a format other than an Audio CD and
JPEG/MP3 file format cannot be played back.
• Discs may not be played back depending on their
recording status or the status of the disc itself.
• Discs may not be played back depending on their
compatibility with this Player.
Discs that Cannot Be Used with
This Player
MP3 files are audio data compressed in the
MPEG1/2 Audio layer-3 file format. “MP3 files” have
“.mp3” as extensions. (Some files that have “.mp3”
extensions or files that have not been recorded in
MP3 format will produce noise or cannot be played.)
The following discs cannot be played back or will
not play back properly on this Player. If such a
disc is mistakenly played back, speaker damage
may occur. Never attempt to play back these
discs.
Playing the MP3 file format
• The MP3 files are not played in the order they were
recorded.
• It is recommended to record data at a lower speed as
data recorded at a fast speed can produce noise and
may not be able to be played.
• The more folders there are, the longer the reading time.
• Depending on the folder tree, reading MP3 files can take
time.
*2 About the JPEG file format
CDG, Video CD, Photo CD, CD-ROM, CD-TEXT,
SVCD, SACD, PD, CDV, CVD, DVD-RAM, DVD-
Audio, BD-RE with the cartridge, CD-WMA
JPEG is a type of file format for storing still-image
files (photos, illustrations, etc.). The Player lets you
play JPEG format still-image files.
File formats that are not compatible.
• Still images in formats other than JPEG (such as TIFF)
cannot be played.
• There may be some files that cannot be played even if
they are in JPEG format.
• Progressive JPEG files cannot be played.
• Moving image files as well as Motion JPEG format files
cannot be played, even though they are JPEG files.
Discs with unusual shapes cannot be played.
• Discs with unusual shapes (heart-shaped or hexagonal
discs, etc.) cannot be used. The use of such discs will
cause malfunction.
• The playing time may not be correctly displayed during
MP3 file playback.
The following files cannot be played on this
player.
• When both Audio CD [CD-DA] format and JPEG/
MP3 file formats are recorded on a disc. (The disc is
recognized to be an Audio CD [CD-DA] only tracks in
Audio CD [CD-DA] format are played back.)
• Multi-session discs cannot be played.
The following BD video discs cannot be played.
• Discs not displaying “A” or “ALL” for the region code
(discs sold outside the authorized marketing area).*
• Discs produced illegally.
• Discs recorded for commercial use.
The region code for this product is A.
Other files that cannot be played back.
• You may not be able to play some still images which
you have created, touched up, copied or otherwise
edited on your computer.
• You may not be able to play some still images you have
processed (rotated or saved by overwriting other images
you have imported from the Internet or e-mail).
*
The following DVD video discs cannot be played.
• Discs not displaying “1” or “ALL” for the region code
(discs sold outside the authorized marketing area).*
• Discs produced illegally.
• Discs recorded for commercial use.
The region code for this product is 1.
About the DivX+HD (H.264/MKV) file
format
• DivX playback may not be available depending on the
DivX content or file.
You may experience one or more of the following
symptoms when playing files.
• It may take some time to play files depending on the
number of folders, number of files and volume of data
involved.
• EXIF information will not be displayed. EXIF stands for
Exchangeable Image File Format, and is a standard for
storing interchange information in image files, especially
for more information.)
*
The following BD-RE/R, DVD-RW/R and
DVD+RW/R discs cannot be played.
• Discs on which data has not been recorded cannot be
played back.
The following Audio CD*1 discs cannot be played.
• Discs containing a signal for the purpose of protecting
copyrights (copy control signal) may not be played back
with this Player.
• This Player has been designed on the premise of
playing back Audio CDs that comply with CD (Compact
Disc) standards.
10
About Media Types
About files/folders for Still images (JPEG
ABOUT DivX VIDEO
Title, Chapter and Track
• DivX® is a digital video format created by DivX, Inc. This
is an official DivX Certified® device that plays DivX video.
tools to convert your files into DivX video.
files) and audio data (MP3 files)
You can play still images (JPEG files) /audio data
(MP3 files) with this unit by making folder(s) on discs
or USB memory devices as shown below.
• Blu-ray discs and DVDs are divided into “Titles”
and “Chapters”. If the disc has more than one
movie on it, each movie would be a separate
“Title”. “Chapters”, on the other hand, are
subdivisions of titles. (See Example 1.)
• Audio CDs are divided into “Tracks”. You can think
of a “Track” as one tune on an Audio CD. (See
Example 2.)
DivX Certified® to play DivX® and DivX Plus™ HD
(H.264/MKV) video up to 1080p HD including premium
content.
Example of a folder structure:
Root
L
001.jpg/001.mp3
ABOUT DivX VIDEO-ON-DEMAND
• This DivX Certified® device must be registered in order
to play purchased DivX Video-on-Demand (VOD)
movies. To obtain the registration code, locate the DivX
VOD section in your device setup menu. Go to vod.
divx.com for more information on how to complete your
registration.
xxx.jpg/xxx.mp3
L
Example 1: Blu-ray disc or DVD
001.jpg/001.mp3
256.jpg/256.mp3
01 Folder
Folder
Title 1
Title 2
001.jpg/001.mp3
255.jpg/255.mp3
L
L
Chapter 1
Chapter 2
Chapter 3
Chapter 1
About Disc Contents
BD Video
Example 2: Audio CD
xxx Folder
001.jpg/001.mp3
256.jpg/256.mp3
Enjoy BD-specific functions including BONUSVIEW
(BD-ROM Profile 1 Version 1.1), such as picture-in-
picture, and BD-LIVE (page 28).
Track 1
Track 2
Track 3
Track 4
L
Including the root directory, the maximum number of folders
and files in each folder is limited to 256 in total.
For the BD video discs compatible with
File and folder requirements
• The discs or USB memory devices which this player
can play back (recognize) are limited to the following
properties:
BONUSVIEW/BD-LIVE, you can enjoy additional
contents by copying the data from the discs or
downloading it via the Internet. For instance, this
function is capable of playing the original movie as
the primary video while playing video commentary
from the film director on a small screen as a
secondary video.
Contains EXIF format files (only JPEG files)
Picture resolution: Between 32 x 32 and 7680 x 4320
pixels (only JPEG files)
Maximum number of folders and files in each folder:
256
Maximum hierarchy level of folders: 5
File size: 20 MB or less (JPEG files)
200 MB or less (MP3 files)
NOTE
• The available functions differ depending on the disc.
NOTE
• File and folder names displayed on this player may differ
from those displayed on PCs.
11
About Media Types
2
3
4
Subtitle languages
Icons Used on BD/DVD Video Disc
Cases
This indicates the kind of subtitles.
Screen aspect ratio
Movies are shot in a variety of screen modes.
The back of the case of a BD/DVD that is
commercially available usually contains various
information about the contents of the disc.
Camera angle
Recorded onto some BD/DVD discs are scenes
which have been simultaneously shot from a number
of different angles (the same scene is shot from the
front, from the left side, from the right side, etc.).
1
2
1. English
2. Chinese
1. English
2. Chinese
2
5
2
Region code
This indicates the region code (playable region code).
3
4
5
The Icons Used in This Operation
Manual
213
546
16:9 LB
2
.............. Indicates the functions that can be
performed for BD Video discs.
DVD Video BD Video
BD VIDEO
1
Audio tracks and audio formats
.............. Indicates the functions that can be
performed for BD-RE discs.
BD-RE
BD and DVD discs can contain up to 8 separate
tracks with a different language on each. The first in
the list is the original track.
.............. Indicates the functions that can be
performed for BD-R discs.
BD-R
This section also details the audio format of each
soundtrack — Dolby Digital, DTS, MPEG etc.
...........Indicates the functions that can be
DVD VIDEO
performed for DVD Video discs.
Dolby Digital
.............. Indicates the functions that can be
performed for DVD-RW discs.
A sound system developed by Dolby Laboratories Inc.
that gives movie theater ambience to audio output
when the Player is connected to a Dolby Digital
processor or amplifier.
DVD-RW
DVD-R
AUDIO CD
CD-R
.............. Indicates the functions that can be
performed for DVD-R discs.
DTS
.............. Indicates the functions that can be
performed for Audio CDs.
DTS is a digital sound system developed by DTS, Inc.
for use in cinemas.
.............. Indicates the functions that can be
performed for CD-R discs.
Linear PCM
Linear PCM is a signal recording format used for
Audio CDs and on some DVD and Blu-ray discs. The
sound on Audio CDs is recorded at 44.1 kHz with
16 bits. (Sound is recorded between 48 kHz with 16
bits and 96 kHz with 24 bits on DVD video discs and
between 48 kHz with 16 bits and 192 kHz with 24 bits
on BD video discs.)
.............. Indicates the functions that can be
performed for CD-RW discs.
CD-RW
USB
.............. Indicates the functions that can be
performed for USB memory devices.
12
Important Information
Cleaning the Pick Up Lens
•
is a trademark of DVD Format/Logo Licensing
Corporation.
Disc Precautions
• Never use commercially available cleaning discs. The
use of these discs can damage the lens.
• Request the nearest service center approved by SHARP
to clean the lens.
• “HDMI, the HDMI logo and High-Definition Multimedia
Interface are trademarks or registered trademarks of
HDMI Licensing LLC in the United States and other
countries.”
• “x.v.Color” and “x.v.Color” logo are trademarks of Sony
Corporation.
• Java and all Java-based trademarks and logos
are trademarks or registered trademarks of Sun
Microsystems, Inc. in the United States and/or other
countries.
• “BONUSVIEW” logo is a trademark of Blu-ray Disc
Association.
• “AVCHD” and the “AVCHD” logo are trademarks of
Panasonic Corporation and Sony Corporation.
• “Blu-ray 3D” and “Blu-ray 3D” logo are trademarks of
Blu-ray Disc Association.
• Netflix and the Netflix logo are the registered trademarks
of Netflix, Inc.
• YouTube is a trademark of Google Inc.
• VUDU™ is a trademark of VUDU, Inc.
• DivX®, DivX Certified®, DivX PlusTM HD and associated
logos are trademarks of DivX, Inc. and are used under
license.
• LC_LCFONT+ and LC logo
mark are registered trademarks of SHARP Corporation.
This product is embedded with LC Font technology,
which was developed by SHARP Corporation for clearly
displaying easy-to-read characters on an LCD screen.
However, other non-LCD fonts are used for displaying
some screen pages.
Be Careful of Scratches and Dust
• BD, DVD and CD discs are sensitive to dust, fingerprints
and especially scratches. A scratched disc may not
be able to be played back. Handle discs with care and
store them in a safe place.
Warnings about dew formation
• Condensation may form on pick up lens or disc in the
following conditions:
− Immediately after a heater has been turned on.
− In a steamy or very humid room.
− When the Player is suddenly moved from a cold
environment to a warm one.
When condensation forms:
Proper Disc Storage
Place the disc in the center
of the disc case and store the
case and disc upright.
• It becomes difficult for the Player to read the signals
on the disc and prevents the Player from operating
properly.
Avoid storing discs in locations
subject to direct sunlight,
close to heating appliances or
in locations of high humidity.
To remove condensation:
• Take out the disc and leave the Player with the
power off until the condensation disappears. Using
the Player when there is condensation may cause
malfunction.
Do not drop discs or subject
them to strong vibrations or
impacts.
License and Copyright
Avoid storing discs in locations
where there are large amounts
of dust or moisture.
Audio-visual material may consist of copyrighted
works which must not be recorded without the
authority of the owner of the copyright. Refer to
relevant laws in your country.
• “This item incorporates copy protection technology
that is protected by U.S. patents and other intellectual
property rights of Rovi Corporation. Reverse engineering
and disassembly are prohibited.”
Handling Precautions
• If the surface is soiled, wipe gently with a soft, damp
(water only) cloth. When wiping discs, always move the
cloth from the center hole toward the outer edge.
• Manufactured under license from Dolby Laboratories.
“Dolby” and the double-D symbol are trademarks of
Dolby Laboratories.
ENERGY STAR® Program Information
• Manufactured under license under U.S. Patent #’s:
5,451,942; 5,956,674; 5,974,380; 5,978,762; 6,226,616;
6,487,535; 7,392,195; 7,272,567; 7,333,929; 7,212,872
& other U.S. and worldwide patents issued & pending.
DTS and the Symbol are registered trademarks, &
DTS-HD, DTS-HD Master Audio | Essential and the DTS
logos are trademarks of DTS, Inc. Product includes
software. ©DTS, Inc. All Rights Reserved.
• Do not use record cleaning sprays, benzene, thinner,
static electricity prevention liquids or any other solvent.
• Do not touch the surface.
Products that have earned
the ENERGY STAR® are
designed to protect the
environment through
• Do not stick paper or adhesive labels to the disc.
• If the playing surface of a disc is soiled or scratched,
the Player may decide that the disc is incompatible
and eject the disc tray, or it may fail to play the disc
correctly. Wipe any dirt off the playing surface with a
soft cloth.
superior energy efficiency.
•
is a trademark.
• “BD-LIVE” logo is a trademark of Blu-ray Disc
Association.
ENERGY STAR® is a U.S. registered mark.
13
Major Components
Main Unit (Front)
Main Unit (Rear)
3
4
1
3
4
5
6
7
2
13
5
6
1
2
10
8
9
11
12
1
POWER (p. 21)
POWER (ON/STANDBY) indicator (p. 21)
d PLAY (p. 25)
H STOP (p. 25)
G REV (p. 35)
0 Front panel display (p. 21)
• The elapsed time is displayed during
playback.
1
RS-232C terminal (p. 57)
2
3
4
5
6
7
2 AC IN terminal (p. 20)
3 ETHERNET terminal (p. 18)
4 W-LAN /USB1 terminal (p. 19, 27)
5 HDMI OUT terminal (p. 16)
• When skipping is performed,
the chapter (or track) number is
displayed.
*
J FWD (p. 35)
OPEN/CLOSE (p. 25)
6 DIGITAL AUDIO OUT OPTICAL terminal (p. 17)
Q BD/DVD/CD mode indicator (p. 21)
W Door flap
E Disc tray (p. 25)
The supplied wireless LAN adapter can be connected to this player.
*
8 USB2 terminal (p. 32)
9 Remote control sensor (p. 20)
NOTE
• When you insert or remove a USB memory device, be sure to turn the main power off.
Also, be sure to set “Quick Start” to “No” (See page 43) before inserting or removing
the device. If you insert or remove the device with the player or Quick Start on, the data
may become damaged.
14
Major Components
1
POWER (p. 21)
m OPEN/CLOSE (p. 25)
Buttons under the cover
Remote Control Unit
2
3 TOP MENU/TITLE LIST (pp. 26, 29)
4 DISPLAY (pp. 26, 36)
5 Cursor buttons (a/b/c/d), ENTER (pp. 22, 24, 40)
6 EXIT (p. 31, 34, 40)
31
32
30
7
A (Red), B (Green), C (Blue), D (Yellow)
(pp. 29, 30, 31, 33, 49)
1
2
16
8 AUDIO (p. 37), SUBTITLE (p. 37), ANGLE (p. 37)
9 PinP (p. 28)
0 REPEAT (p. 36), OFF (for REPEAT) (p. 36)
Q S REV (p. 35)
W T SKIP/k (pp. 29, 35)
E REPLAY (p. 36)
33
17
18
3
4
R
(Lock) (See below.)
19
TNETFLIX (p. 55)
NOTE
Y TV CONTROL buttons (p. 22)
UHOME (pp. 22, 31–34, 40)
I POP-UP MENU (p. 27)
O FUNCTION (p. 38)
Pn RETURN (pp. 31, 33, 34, 36)
A PAGE r/s (p. 30)
Sd PLAY (p. 25)
5
• This remote control unit is equipped with two ENTER
buttons (5 and 31 listed above). The ENTER button
under the cover is useful when using with the number
buttons.
6
7
8
9
10
11
20
21
22
23
24
25
26
Keylock function
You can set the keylock to prevent accidental
operations.
This function allows TVs compatible with AQUOS
LINK to also perform a Key Lock on the player.
DV FWD (p. 35)
FF PAUSE (pp. 31, 32, 33, 35)
GU SKIP/l (pp. 29, 35)
HSKIP SEARCH (p. 36)
JH STOP (p. 25)
K3D (p. 23)
LVUDU (p. 56)
+Number buttons (p. 39)
Z ENTER (p. 39)
This button is the same operation as 5 ENTER.
XCLEAR (p. 39)
Press and hold
seconds.
(Lock) for more than 2
12
13
• Each time you perform this operation, the
function is activated or deactivated.
• If you try to operate the Player while the
keylock function is set, “Hold” blinks on the
front display panel to indicate that the keylock
function is set.
27
28
29
14
15
To clear the input number.
CNon-functional buttons
They have no operation at all.
These buttons on the remote control are non-
functional.
15
Connection
Connecting to a TV/projector
You can enjoy high quality digital picture and sound using an HDMI cable. (Only
TVs/projectors with an HDMI terminal can be connected to this player.)
When you use AQUOS LINK, make sure to use a certified HDMI cable.
NOTE
• In this player, “HDMI Video Out” is set to “Auto” as a default (See page 42). (Normally
set to “Auto”.) If you don’t get a stable image with “HDMI Video Out” set to “Auto”,
select the output resolution which corresponds to the connected equipment.
• To enjoy 3D images, connection to a 3D compatible TV is needed.
1 Be sure to turn off this Player and the TV/projector before making any
connections.
• For connection to a TV/projector, refer to the TV/projector’s operation manual.
2 Firmly connect an HDMI cable (commercially available) to the HDMI OUT
terminal on the player (1) and the HDMI IN terminal of the TV/projector (2).
E
After connecting
• If desired, connect audio equipment. (Page 17)
• If necessary, perform the Audio Video Settings. (Pages 42–43)
• Refer to AQUOS LINK function. (Pages 23 and 43)
• Prepare the desired disc or content and start playback. (Pages 25–34, 55)
HDMI cable
(commercially available)
Projector
TV
16
Connecting to an amplifier/AV receiver
You can connect this player to an amplifier/AV receiver to enjoy digital surround
sound. With this player, the audio connection can be made using either one of
the following methods depending on the capabilities of the amplifier/AV receiver
you connect.
NOTE
• When using an HDMI output, 7.1 ch Digital Output is available.
• Audio transmitted in DTS-HD High Resolution Audio and DTS-HD Master Audio
formats is output from the HDMI terminal as Bitstream. Connect an amplifier with a
built-in decoder to enjoy the fine sound quality.
• When a connection to a 3D TV is made via an amplifier/AV receiver, it is necessary to
connect to a 3D compatible amplifier/AV receiver.
If the amplifier/AV receiver is not 3D compatible, connect the HDMI cable to the TV
directly while connecting the player and the amplifier/AV receiver using an optical
digital cable.
• HDMI connection
• Digital audio connection
NOTE
• Be sure to turn off this Player and the equipment before making any connections.
• For details on output of audio formats, see page 54.
HDMI connection
Digital audio connection
You can connect an amplifier/AV receiver using an optical digital audio cable
(commercially available).
HDMI cable
*
Optical digital cable
*
Amplifier/AV receiver
Commercially available
*
TV
Amplifier/
AV receiver
HDMI cable
*
NOTE
• When using OPTICAL DIGITAL AUDIO OUT, 5.1ch Digital Output is available. (7.1ch
Digital Output is not available.)
Commercially available
*
E
After connecting
• If necessary, perform the Audio Video Settings. (Pages 42–43)
• Prepare the desired disc or content and start playback. (Pages 25–34, 55)
17
Broadband Internet Connection
By connecting this player to the Internet, you can enjoy a variety of content
on your TV using BD-LIVE functions, video on-demand services (e-Contents),
home networks and also perform software updates. In this player, the Internet
connection can be made using either one of the following methods.
• Wired connection (LAN cable)
Wired connection (LAN cable)
Connect a LAN cable (commercially available) to the ETHERNET terminal of this
player (1) and the LAN port of the broadband router (2).
• Wireless connection (wireless LAN) (See page 19.)
NOTE
• Be sure to turn off this Player and the equipment before making any connections.
• When an Internet connection is made, wired and wireless connections cannot be used
at the same time. Use only one of the connection types (See page 46).
CAUTION
• When using a broadband Internet connection, a contract with an Internet service
provider is required. For more details, contact your nearest Internet service provider.
• Refer to the operation manual of the equipment you have as the connected equipment
and connection method may differ depending on your Internet environment.
LAN cable
*
PC
LAN
Internet
Modem
Broadband
router
Commercially available
*
NOTE
• Use a LAN cable/router supporting 10BASE-T/100BASE-TX.
• SHARP cannot guarantee that all brands’ broadband routers will operate with this
player.
E
After connecting
• Perform the communication settings. (Pages 46–49)
• When enjoying BD-LIVE functions, see pages 28 and 44.
• When enjoying video on-demand services (e-Contents), see pages 55–56.
• To play back files via the Home Network, see page 34.
• To update the software via the Internet, perform Software Update Settings.
(Pages 51–52)
18
Broadband Internet Connection
NOTE
Wireless connection (wireless LAN)
• When you insert or remove a wireless LAN adapter, be sure to turn the main power off
and make sure that “Quick Start” is set to “No” (See page 43).
• You must use a wireless router/access point that supports IEEE802.11 b/g/n. (n is
recommended for stable operation of the wireless network.)
• Wireless LAN, in its nature, may cause interference, depending on the usage conditions
(access point performance, distance, obstacles, interference by other radio devices,
etc.).
Insert the wireless LAN adapter (supplied) into the W-LAN/USB1 terminal on the
rear of the player.
• Set the wireless router/access point to Infrastructure mode. Ad-hoc mode is not
supported.
• SHARP cannot guarantee that wireless LAN adapters other than the supplied adapter
will operate with this player.
• SHARP cannot guarantee that all brands’ wireless routers will operate with this player.
E
After connecting
• Perform the communication settings. (Pages 46–49)
• When enjoying BD-LIVE functions, see pages 28 and 44.
• When enjoying video on-demand services (e-Contents), see pages 55–56.
• To play back files via the Home Network, see page 34.
• To update the software via the Internet, perform Software Update Settings.
(Pages 51–52)
Wireless LAN adapter
(Supplied)
PC
Wireless
router
Modem
Internet
When a wireless connection is made, it is necessary to enter the MAC address
shown on the wireless LAN adapter for the wireless router. We recommend writing
down the MAC address in this operation manual. (See page 48.)
19
Playback
Before Starting Playback
WARNING
Loading the Batteries in the Remote
Control
Connecting the Power Cord
• Do not use or store batteries in direct sunlight or other
excessively hot place, such as inside a car or near a
heater.
This can cause batteries to leak, overheat, explode or
catch fire.
Plug the supplied AC cord into the AC IN terminal on
the rear of the Player (1). Then plug into AC outlet
(2).
1 Hold in the tab on the battery cover and pull the
cover towards the direction of the arrow.
It can also reduce the life or performance of batteries.
NOTE
• Do not subject the remote control unit to shock, water
or excessive humidity.
• The remote control unit may not function if the Player’s
remote sensor is in direct sunlight or any other strong
light.
• Incorrect use of batteries may cause them to leak or
burst. Read the battery warnings and use the batteries
properly.
• Do not mix old and new batteries, or mix different
brands.
• Remove the batteries if you will not use the remote
control unit for an extended period of time.
2 Load the two “AAA” size batteries (R-03 size,
UM/SUM-4). Place batteries with their terminals
corresponding to the m and n indications in
battery compartment.
NOTE
• Place the Player close to the AC outlet, and keep the
power plug within reach.
• TO PREVENT RISK OF ELECTRIC SHOCK, DO NOT
TOUCH THE UN-INSULATED PARTS OF ANY CABLES
WHILE THE AC CORD IS CONNECTED.
• The POWER (ON/STANDBY) indicator blinks while the
Player is preparing for starting up. You cannot turn the
Player on until the POWER (ON/STANDBY) indicator
stops blinking.
Approximate operating range of
remote control
Remote control sensor
• If you are not going to use this Player for a long period
of time, be sure to remove the AC cord from the AC
outlet.
3 Insert the smaller tab of the battery cover into
the opening 1, and press down on the cover
until it clicks in place 2.
15º
*Approx. 22 feet (7m)
30º
30º
15º
Remote control unit
20
Before Starting Playback
Turning the Power On
Turning the power on
Indicators on the Player
Press POWER on the remote control or on the
Player to turn on the power of the Player.
POWER (ON/STANDBY) indicator
Green on
Red on
Power on
Standby
BD/DVD/CD mode indicator
NOTE
Blue on
Playing back
Loading a disc/updating
• When you turn on this player for the first time after
purchase or when you turn on this player after you
perform “System Reset” (see page 45), the language
setting screen will be displayed, so please perform the
language setting (see step 3 of page 22).
Blue blinks
1
About the Home screen
2
4
3
When turning on the player, the Home screen
appears.
Entering standby
Home screen
Press POWER on the remote control or on the
Player to enter standby.
Video
BD-Video
USB
1 POWER button
Music
2 POWER (ON/STANDBY) indicator
3 Front panel display
4 BD/DVD/CD mode indicator
1
Picture
e-Contents
Settings
Home Network
• If you press POWER again immediately after entering
standby, the Player may not turn on. If this happens,
wait for 10 seconds or more and then turn on the power
again.
Select
ENTER
EXIT
Enter
Return
Exit
NOTE
32 4
1 Main menu
2 Icon for disc inserted
5
• When the POWER (ON/STANDBY) indicator is blinking
(may take some time), the Player cannot be turned on.
3 Icon for USB memory device connected
4 Icon for LAN connection
5 Button Guide
21
Before Starting Playback
Language Setting
Operating a SHARP TV Using the
Remote Control
Turning Off the LCD Backlight and
Indications
The Universal Remote Control may operate the
basic functions of the SHARP TV.
If you feel that the indicators on the player’s front
display are too bright when watching movies, you
can turn them off except for the POWER (ON/
STANDBY) indicator.
TV function control
Changing the on-screen display
language
1 Press a/b to select “Settings”, then press d or
• TV Power: POWER
ENTER.
1 Press a/b to select “Settings”, then press d or
• TV-AV Selector: INPUT
2 Press a/b to select “On Screen Language”,
ENTER.
• TV Volume up/down: VOL e/f
• TV Channel up/down: CH r/s
then press d or ENTER.
2 Press a/b to select “Smart Settings”, then
Audio Video Settings
Smart Settings
press d or ENTER.
Video
3 Press a/b to select “Front Display/LED”, then
AQUOS LINK
Playback Setting
On Screen Language
Communication Setup
Version
USB Memory Management
Music
press d or ENTER.
Picture
4 Press a/b to select “On” or “Off”, then press
ENTER.
e-Contents
5 Press HOME or EXIT to exit.
Software Update Settings
Settings
System
3 Press a/b to select the language you want to
display on the screen, then press ENTER.
NOTE
• To select the DVD disc language, such as subtitle
language, etc., see page 26.
22
Before Starting Playback
Using AQUOS LINK
E
AQUOS PURE MODE
NOTE
When you connect this player to an AQUOS LCD
TV compatible with AQUOS LINK and set “AQUOS
LINK” to “Yes” (page 43), images automatically
adjusted to the most suitable image quality for the
AQUOS TV are output from the HDMI OUT terminal
of this player.
• The 3D mode can be switched only when playback is
stopped.
• Depending on the connected TV, the images during
playback may switch to 2D images due to changes in
the resolution, etc. Make sure the 3D image setting is
performed on the TV.
• The 3D images may not be output as set in “HDMI
Video Out”.
• When performing Fast Forward/Reverse, images are
shown in 2D.
Controlling the Blu-ray disc player
using AQUOS LINK
What is AQUOS LINK?
NOTE
Using the HDMI CEC (Consumer Electronics
Control), with AQUOS LINK you can interactively
operate this player with your SHARP AQUOS TV.
• In order to make AQUOS LINK available, set “AQUOS
LINK” to “Yes” (See page 43).
Refer to the Operation Manual of the TV for details
regarding setup.
What you can do with AQUOS LINK
CAUTION
When you connect this player to the LCD TV
compatible with AQUOS LINK using an HDMI cable,
you can perform the functions listed below. (See
page 16 for connecting to the HDMI terminal).
• When viewing 3D images, viewing for a long period
of time or lying on your back may cause eye strain
and discomfort. In addition, 3D images may affect the
eyesight of young children/infants, so keep them from
viewing the images.
Using 3D
This sets output of 3D images.
E
Automatic input select function
To view 3D images, playback of 3D content (3D BD
video) is necessary with a 3D compatible TV and 3D
glasses in addition to this player.
When you start playback of this player, the input
selector of the LCD TV will automatically switch to
the LCD TV input terminal connected to the player
and the playback image will appear on the screen,
even if you are watching a TV program.
E
Automatic power off function
Press 3D to change to the 3D mode.
• Each time the button is pressed, the mode switches
between “Auto(3D)” and “2D”.
• The status of the selected mode will be displayed on the
TV screen.
If you turn off the LCD TV when this player is in stop
mode, the power of this player will be turned off
automatically. (However, when playing back a disc
or other content using this player, the power does
not turn off.)
Auto: Video signals are output as 3D when 3D content (3D
BD video) is played or as 2D when 2D content is played.
2D: Even if 3D content (3D BD video) is played, video
signals are output as 2D at all times.
E
Automatic power on function
When you switch to the LCD TV input terminal
connected to this player, the power of this player will
be turned on automatically.
• This setting (Auto(3D)/2D) can also be performed using
the menu screen (See page 45).
23
Before Starting Playback
Control Panel
Control Panel
Major functions of each button icon
This function allows you to operate this player using
the TV remote control by displaying the control
panel on the TV screen.
• Display the pop-up menu screen for BD
video and the menu screen for DVD video.
POP-UP
MENU
POP-UP
MENU
TOP MENU
TITLE LIST
FUNC.
• To operate this function, connect this player to a TV
compatible with HDMI CEC (Consumer Electronics
Control) using an HDMI cable (See page 16). Make
sure that “Control Panel” is set to “Yes” (See page 43).
When the settings are completed, perform the following
operations.
• Display the top menu screen for BD video
and DVD video.
TOP MENU
TITLE LIST
• Display the Function Control screen for BD
video, DVD video, etc.
FUNC.
NOTE
• The control panel may not be displayed depending on
the TV. Also, it may not be available depending on the
content.
• When operating using the remote control of the player,
the control panel does not appear.
• Fast reverse (search).
• Play.
• When playing video on demand streaming content
available with this player, the control panel cannot be
displayed.
PANEL
OFF
Select
Enter
• Fast forward (search).
• Skip to the beginning of a chapter.
• Pause.
1 Switch the TV input to the input source to which
• When there is no operation for approximately
10 seconds, the control panel disappears
automatically.
To display the control panel, press the PLAY button
on the TV remote control.
this player is connected (HDMI input).
2 Press the PLAY button on the TV remote control.
• The control panel appears on the TV screen.
3 Press a/b/c/d on the TV remote control
to select the desired button icon, then press
ENTER.
• The function of the selected button icon is available.
• Skip to the next chapter.
• Jump backward (approx. 10 seconds).
(This function is used when you want to re-
watch a scene that has just been shown.)
• Stop.
• Jump ahead (approx. 30 seconds).
PANEL
OFF
• Turn off the control panel.
24
Video/Picture/Music Playback
NOTE
Loading a Disc
BD/DVD Video Playback
• The disc load time may vary depending on the disc.
BD VIDEO
BD-RE
BD-R
Regarding playback of BD video discs
• Some of the newly released BD video discs cannot be
played back unless you update the player software
to the latest version. Therefore, it may be required to
update the software of the player.
• Refer to pages 51–54 for more information regarding
software updates for the player.
DVD VIDEO
DVD-R DVD-RW
This section explains playback of commercially
available BD Video and DVD Video discs (like
movies) and recorded DVD-RW/R discs.
• This player supports DVD upscaling during DVD
playback.
• For a description of other playback functions, refer to
“Playback Functions” on pages 35–37.
POWER
OPEN/CLOSE
To stop playback
Press c.
Resume playback function
• If you press a next, playback will resume from
the point where the Player was previously stopped. To
playback from the beginning, cancel resume mode by
pressing c, then press a. (This may not
work depending on the type of disc. In this case, open
the disc tray or enter standby.)
1 Press POWER to turn on the power.
2 Press OPEN/CLOSE to open the disc tray.
1 Load a disc.
3 Load a disc on the disc tray.
• Insert the disc with the label face up.
• In case of disc recorded on both sides, face down
the side to play back.
NOTE
• Playback may begin automatically, depending on
the disc.
• Resume playback may not function depending on the
disc.
• The resume playback function for discs will be cancelled
if video on demand streaming content is viewed
after disc playback. Disc playback will start from the
beginning after viewing streaming content.
• Playback begins from the first title.
• The menu may be displayed first, depending on the
disc. Perform playback operation by following the
directions on the screen.
• When loading a disc containing 3D content (3D BD
video) with “Yes” selected in the “3D Notice” setting
(page 45), playback will be stopped and the 3D
notice will be displayed on the TV screen. In such
cases, press ENTER for confirmation, and then
playback will start.
4 Press OPEN/CLOSE to close the disc tray.
2 Press a if playback does not begin
automatically or playback is stopped.
25
Video/Picture/Music Playback
NOTE
Displaying the disc information
BD/DVD Menus
• The procedure explained on this page is the basic
operation procedure. Procedures vary depending on
the BD/DVD video disc, so you may need to follow the
instructions in the BD/DVD video disc manual or the
instructions displayed on the screen.
• This section explains how to play back a BD/DVD
video disc with a top menu, disc menu or pop-up
menu.
• The titles listed in the top menu and a disc guide
(for options like subtitles and audio languages) are
given in the disc menu.
Top menu
• With some BD/DVD discs, the top menu may be
referred to as the “Title Menu”. Use TOP MENU/TITLE
LIST on the remote control when the instructions refer
to “Title Menu”.
Press DISPLAY during playback.
• Each time you press DISPLAY, the display switches
as follows.
• If no top menu is available, the TOP MENU/TITLE LIST
button will have no effect.
1
BD-VIDEO
Disc Information
screen A
2
3
4
1/1
1 10/ 1
00:00:12
/03:12:28
Using the disc menu
DVD VIDEO
Start playback by selecting a title
from the top menu
Example: Select “SUBTITLE LANGUAGE”.
00:00:12
/03:12:28
4
Disc Information
screen B
1 Press TOP MENU/TITLE LIST.
• The disc menu screen is displayed if present on the
DVD video disc.
BD VIDEO DVD VIDEO
No Display
2 Press a/b to select “SUBTITLE LANGUAGE”,
1 Press TOP MENU/TITLE LIST.
• The top menu screen is displayed if present on the
BD/DVD video disc.
then press ENTER.
1 Type of disc
• The screen for selecting the subtitle language is
displayed.
2 Title number being played / Total number of Titles
3 Chapter number being played / Total number of
Chapters
Example
Example
4 Elapsed playback time / Total playback time for
the Title
T O P M E N U
MENU
1
3
2
Jazz
Latin
1
2
3
AUDIO LANGUAGE
SUBTITLE LANGUAGE
AUDIO
NOTE
• Disc Information Screen A disappears after about 1
minute elapses without performing any operations.
• For some commercially-released BD VIDEO discs, the
total playback time display for the Chapter/Title may not
appear.
4
Classic
Rock
2 Press a/b/c/d to select the title, then press
ENTER.
3 Press a/b to select the subtitle language, then
• The selected title is played back.
press ENTER.
4 Press TOP MENU/TITLE LIST to exit.
26
Video/Picture/Music Playback
Virtual Package/BD-LIVE data is saved in Local
Storage (USB memory device connected to this
Player). To enjoy these functions, connect a USB
memory device (2GB or greater) supporting USB
2.0 High Speed (480Mbit/s) to the USB1 or USB2
terminal on this player.
Front
Using the pop-up menu
BD VIDEO
USB memory
device
1 Press POP-UP MENU during playback.
• The pop up menu screen is displayed.
• The menu contents displayed vary depending on
the disc. For details on how to see and operate the
pop-up menu, refer to the manual for the disc.
When the wireless LAN adapter is not inserted into the
USB1 terminal on the rear of the player, it is recommended
that the USB memory device be connected to the USB1
terminal. (When you insert or remove a USB memory
device, be sure to turn the main power off and make sure
that “Quick Start” is set to “No” (See page 43).)
USB2 terminal
• If there is insufficient storage space, the data will not
be copied/downloaded. Delete unneeded data or use a
new USB memory device.
• If a USB memory device containing other data
(previously recorded) is used, the video and audio may
not play back properly.
• If the USB memory device is disconnected from this
player during playback of Virtual Package/BD-LIVE data,
playback of the disc will stop.
• Some time may be required for the data to load (read/
write).
Example
Pop-up menu
NOTE
Previous page
Next page
• A USB memory device can be used with either the
USB1 or USB2 terminal. When two USB memory
devices are connected to both terminals at the same
time, in certain situations the USB1 terminal may give
priority to Local Storage and the USB2 terminal cannot
be used for Local Storage.
2 Press a/b/c/d to select the desired item,
then press ENTER.
• Refer to “USB Memory Management” on page 50 for
erasing the Virtual Package data and the BD-LIVE data
in the USB memory device.
3 Press POP-UP MENU to exit.
• The pop-up menu will automatically disappear for
some discs.
Rear
NOTE
Enjoying BONUSVIEW or BD-LIVE
USB1 terminal
• SHARP cannot guarantee that all brands’ USB memory
devices will operate with this player.
• Only USB memory devices formatted with FAT 32/16 are
compatible.
When formatting a USB memory device using a PC,
perform the following settings.
− Format File System: FAT32
− Allocation Unit Size: Default Allocation Size
• Do not use a USB extension cable when connecting a
USB memory device to the USB terminal of the player.
− Using a USB extension cable may prevent the player
from performing correctly.
BD VIDEO
This Player is compatible with additional functions of
BD-Video, BONUSVIEW (BD-ROM Profile 1 Version
1.1) and BD-LIVE.
For BD-Video discs compatible with BONUSVIEW,
the functions of Picture in Picture and Virtual
Package are available. For BD-LIVE compatible
discs, you can enjoy a variety of functions via the
Internet in addition to the BONUSVIEW functions.
USB memory device
27
Video/Picture/Music Playback
NOTE
Use of Picture in Picture function
(secondary audio/video playback)
Virtual Package
• Regarding playback method of BD-LIVE contents,
etc., perform the operations in accordance with the
instructions in the BD disc manual.
• To enjoy BD-LIVE functions, perform the broadband
Internet connection (pages 18–19) and communication
settings (pages 46–49).
• Before using this function, please read “Network Service
Disclaimer” (page 69).
• Refer to page 44 regarding the setup to restrict access
to BD-LIVE contents.
For BD-Video discs compatible with Virtual
Package, data is copied from the discs or Internet to
local storage. It is automatically copied to the local
storage prior to playback. You can enjoy a variety
of additional functions including secondary video,
secondary audio, subtitles, movie trailers, etc.
• The playback methods vary depending on the disc. For
details, refer to the disc manual.
BD-Video that includes secondary audio and
video compatible with Picture in Picture can be
played back with secondary audio and video
simultaneously as a small video in the corner.
• If the BD-LIVE screen does not appear for a while after
you select the BD-LIVE function in the BD disc menu,
the USB memory device may not have enough free
space. In such cases, eject the disc from the player, and
then erase the data in the USB memory device in the
“USB Memory Management” menu on page 50.
BD-LIVE
1 Press PinP during playback to show the
In this Player, a variety of contents with interactive
functions are available through BD-LIVE compatible
Blu-ray discs by connecting to the Internet. You
can enjoy the download of bonus features such as
latest movie trailers to the USB memory device,
communication compatible BD-J interactive games,
etc.
2-picture screen.
• The available functions differ depending on the disc.
Primary audio/
video
Secondary audio/
video
2 To remove the secondary video, press PinP
again.
NOTE
• To listen to secondary audio, make sure that “Secondary
Audio” is set to “On”. (See page 42.)
• The secondary audio and video for Picture In Picture
may automatically play back and be removed
depending on the content. Also, playable areas may be
restricted.
28
Video/Picture/Music Playback
About Title List
DVD-R/-RW (VR format) / BD-RE/-R
(BDAV format) Playback
Playback by selecting a title
• The Title List can be displayed in two types,
Thumbnail and Title Name.
1 Load a recorded disc.
• Each time you press A (Red), the screen changes
between Thumbnail and Title Name.
DVD-R DVD-RW
BD-RE
BD-R
• The Title List screen is displayed.
Example: Thumbnail screen
You can play back a recorded disc (DVD: VR format
finalized disc only / BD: BDAV format disc only).
• For a description of other playback functions, refer to
”Playback Functions” on pages 35–37.
Thumbnail
Program 1
Program 1
1
5/21 Fri 9:30 AM 110 Min.
5/21 Fri 9:30 AM 110 Min.
Program
1
Program
2
Program
3
Program
1
Program
2
Program
3
Program
4
Program
5
Program
6
Program
4
Program
5
Program
6
EXIT
Select
Title Name
Enter
By Chapter
Return
Playlist
Exit
Functions
EXIT
Select
Title Name
Enter
By Chapter
Return
Playlist
Exit
Functions
3
1
A
B
C
D
A
B
C
D
• If the Title List screen is not displayed, press TOP
MENU/TITLE LIST.
• When loading a BD disc with usage restrictions
placed by a BD recorder, the password input screen
appears. Then, input your password.
If you input a wrong password three times, the disc
tray will open. Close the disc tray, and then input a
correct password.
Title Name
Program 1
5/21 Fri 9:30 AM 110 Min.
1 Program 1
Program
1
5/21 Fri 110 Min.
6/15 Fri 110 Min.
7/3 Mon 56 Min.
9/18 Thu 40 Min.
9/20 Sat 20 Min.
9/25 Thu 60 Min.
2 Program 2
3 Program 3
4 Program 4
5 Program 5
6 Program 6
[From Old]
2 Press a/b/c/d to select the desired title, then
press ENTER to start playback.
2
3
• If you want to select additional titles, switch pages
by pressing PAGE r/s.
The same operation can be performed by pressing
f or g.
• You can playback by pressing a instead of
pressing ENTER.
1/All 8 Titles
EXIT
Select
Thumbnail
Enter
Return
Playlist
Exit
Functions
NOTE
A
B
C
D
Sorting
• “Finalize” refers to a recorder processing a recorded
disc so that it will play in other DVD players/recorders
as well as this player. Only finalized DVD discs will play
back in this player. (This player does not have a function
to finalize discs.)
• Some discs cannot be played back depending on the
audio format.
• BD-RE/-R discs recorded from a BD recorder comply
with AACS copyright protection technology. As this
player is not intended to be compliant with AACS, such
discs cannot be played back.
1 Information of selected title
2 Title Name
Recording Date
Recording Duration
3 Button Guide
3 Press c to stop playback.
NOTE
• The Title List screen also can be displayed by pressing
TOP MENU/TITLE LIST when playback is stopped.
(AACS: Advanced Access Content System)
29
Video/Picture/Music Playback
Playback by selecting a chapter
Playback by selecting a Playlist
Playback from the beginning or
resume playback
1 Press B (Green) while the Thumbnail screen is
displayed.
1 Press C (Blue) while the Title List screen is
displayed.
When you play back the title from the Title List after
you stopped playback, you can select playback
from the beginning or from the point where it was
last stopped.
• The chapter screen is displayed.
• The Playlist screen is displayed.
Example: Thumbnail screen
Chapter
1
Chapter
2
Chapter
3
Program 1
1 Press D (Yellow) when the desired title is
5/21 Fri 9:30 AM 110 Min.
selected while the Title List screen is displayed.
Chapter
4
Chapter
5
Chapter
6
Program
1
Program
2
Program
3
2 Press a/b to select the type of Playback, then
press ENTER to start playback.
• The type of Playback may be selected from “From
Beginning” or “From Continued”.
• If you want to select additional chapters, switch
pages by pressing PAGE r/s.
Program
4
The same operation can be performed by pressing
f or g.
• To return to the Thumbnail screen, press B (Green).
3 Press c to stop playback.
EXIT
Select
Title Name
Enter
By Chapter
Return
Original
Exit
Functions
A
B
C
D
2 Press a/b/c/d to select the desired chapter,
then press ENTER to start playback.
• You can playback by pressing a instead of
pressing ENTER.
2 Press a/b/c/d to select the desired title, then
press ENTER to start playback.
3 Press c to stop playback.
3 Press c to stop playback.
Sorting the titles
Each time you press B (Green) while the Title Name
screen is displayed, the Title Name display changes
between displaying the newest title first and the
oldest title first.
30
Video/Picture/Music Playback
• Playback may begin automatically, depending on
the disc.
Audio CD Playback
Operation procedure for the
“Functions” menu
AUDIO CD
1 Press D (Yellow) (Functions) when the CD screen
is displayed.
This Player can play back audio CDs.
• For a description of other playback functions, refer to
“Playback Functions” on pages 35–36.
• The “Functions” menu is activated.
2 Press a if playback does not begin
automatically or playback is stopped.
3 To pause the playback at any time, press
b.
• Press b or a to return to playback.
2 Press a/b to select the desired setting, then
press ENTER.
4 Press c to stop playback.
5 To return to the HOME screen, press c
• When playback is stopped, only “Track” can be
selected.
again, and then press HOME or EXIT.
• For a description of each setting, see “Functions
which can be set” (Page 39).
Playback by selecting a track
3 Press a/b/c/d to set, then press ENTER.
• Operations vary depending on the setting. Follow
the operation instructions on the screen.
1 Press a/b to select the track, then press
ENTER during playback or when playback is
stopped.
4 Press j or D (Yellow) to exit the
• Playback of the selected track will begin.
“Functions” menu.
Playback from the beginning
NOTE
1 Load an audio CD.
• The displayed items vary depending on the disc.
• The CD screen is displayed.
(The CD screen is displayed only when a compact
disc recorded in the CD-DA format is inserted.)
2 Press c to stop playback.
31
Video/Picture/Music Playback
5 Press ENTER to play back the selected file.
NOTE
Audio Data (MP3 File) Playback
• Playback of the selected file will begin.
• A USB memory device can be used with either the
USB1 or USB2 terminal. When two USB memory
devices are connected to both terminals at the same
time, in certain situations the USB1 terminal may give
priority to Local Storage and MP3 files cannot be played
back using this terminal.
CD-R
CD-RW
DVD-R DVD-RW
USB
This Player can play back audio data (MP3 files)
recorded on CD-R/RW discs, DVD-R/RW discs and
USB memory devices or via a home network.
• For details on the audio data that you can play using
this player, refer to page 11.
• When data in the USB memory device is played back,
playback from the USB memory device will stop when
OPEN/CLOSE on the remote control or the player is
pressed or when a disc is inserted into the player.
2 Press a/b to select “Music”, then press d or
ENTER.
3 Press a/b to select “DVD/CD ”, “USB Memory
*
Device” or “Home Network”, then press d or
• When MP3 files are played, the “Functions” menu is
not available.
ENTER.
Display name varies depending on the type of
media inserted.
*
6 To return to the HOME screen, press c
(press twice if during playback), and then press
HOME or EXIT.
• If only a “DVD/CD” or a USB memory device is
inserted, the “DVD/CD” or “USB Memory Device”
selection screen does not appear. In such cases,
after step 2, proceed to step 4.
List of available buttons during playback
4 Press a/b to select a folder or file.
• When you select a folder, press ENTER to open it,
and then press a/b to select a file in the folder.
Buttons
a/b
Description
Select a desired audio file.
Play back audio file.
ENTER
Folder 1
Pause audio file playback.
• Return to playback when
paused.
b
CD
1 Folder 1
2 Folder 2
3 Folder 3
4 Folder 4
5 Track 01.mp3
6 Track 02.mp3
1/All 14 files and folders
Skip backward.
Skip forward.
Stop playback.
f
g
c
NOTE
1 Load a disc or a USB memory device
*
• The Fast Forward/Reverse function does not work.
• The Repeat function does not work.
containing audio data (MP3 files).
When you insert or remove a USB memory device,
be sure to turn the main power off and make sure
that “Quick Start” is set to “No” (See page 43).
*
• When the wireless LAN adapter is not inserted
into the USB1 terminal on the rear of the player, it
is recommended that the USB memory device be
connected to the USB2 terminal.
32
Video/Picture/Music Playback
5 Press ENTER to display the selected file.
NOTE
Displaying Still Images (JPEG files)
• The selected still image appears on the screen.
• A USB memory device can be used with either the
USB1 or USB2 terminal. When two USB memory
devices are connected to both terminals at the same
time, in certain situations the USB1 terminal may give
priority to Local Storage and JPEG files cannot be
played back using this terminal.
CD-R
CD-RW
DVD-R DVD-RW
USB
1/77
This Player can display still images (JPEG files)
recorded on CD-R/RW discs, DVD-R/RW discs and
USB memory devices or via a home network.
• For details on the still images that you can display using
this player, refer to page 11.
• Still images are played one by one while during “Slide
show”, they are automatically replaced one after
another.
• When data in the USB memory device is played back,
playback from the USB memory device will stop when
OPEN/CLOSE on the remote control or the player is
pressed or when a disc is inserted into the player.
2 Press a/b to select “Picture”, then press d or
ENTER.
3 Press a/b to select “DVD/CD ”, “USB Memory
*
6 To return to the HOME screen, press c,
Device” or “Home Network”, then press d or
and then press HOME or EXIT.
ENTER.
Display name varies depending on the type of
media inserted.
*
Operational buttons during still image
display
• If only a “DVD/CD” or a USB memory device is
inserted, the “DVD/CD” or “USB Memory Device”
selection screen does not appear. In such cases,
after step 2, proceed to step 4.
Buttons
Description
Go to the previous/next picture in
the same directory.
f/
g
4 Press a/b to select a folder or file.
• When you select a folder, press ENTER to open it,
and then press a/b to select a file in the folder.
d/ e
j
C (Blue)
Return to the selection screen.
Folder 1
Rotate the picture by 90 degrees
to the left.
CD
1 Folder 1
2 Folder 2
3 Folder 3
D (Yellow)
Rotate the picture by 90 degrees
to the right.
4 Folder 4
Play back Slide Show.
• Return to slide show playback
when paused.
a
5 Image 01.jpg
6 Image 02.jpg
1/All 14 files and folders
Pause slide show playback.
b
c
• To set slide show speed/repeat playback, press D
(Yellow) (Slide Show Menu).
Stop still image display/slide show
playback.
Slide Show Menu
A (Red)
NOTE
Guide display on/off.
1 Load a disc or a USB memory device
*
Slide Show
Speed
Setting of slide show playback
speed
containing Still Images (JPEG files).
• Thumbnail data will be displayed when JPEG files from
a digital camera contain thumbnail data.
• An icon will be displayed for JPEG files which do not
contain thumbnail data.
When you insert or remove a USB memory device,
be sure to turn the main power off and make sure
that “Quick Start” is set to “No” (See page 43).
*
Repeat Mode
Setting
Setting of slide show repeat
playback
• When the wireless LAN adapter is not inserted
into the USB1 terminal on the rear of the player, it
is recommended that the USB memory device be
connected to the USB2 terminal.
Guide Display
Setting
Guide display setting during still
image display
33
Video/Picture/Music Playback
Accessing DLNA servers
3 Press ENTER or d.
Types of playable files
• The player automatically scans and displays DLNA
servers within your local network.
Video
DivX Plus HD (avi/divx/mkv)
The player can browse and play movies, music and
photos stored on your DLNA Certified media servers
connected within your home network.
Music
Picture
mp3
jpg
Select server
About a home network
NOTE
1. xxxxxxxxxxxxx
2. yyyyyyyyyyyyy
3. zzzzzzzzzzzzzz
4. aaaaaaaaaaaa
This Player can display and play movies, photos
and music content from your DLNA-compatible
digital media servers (such as a PC and consumer
electronics).
• Even if DLNA compatible, a connection may not be
able to be made depending on the server, or playback
may not be available even if a connection is made
successfully.
• Some files may not be playable depending on the file.
For details, refer to pages 10–11.
• To enjoy this function, make a broadband Internet
connection to both your PC and this player (See pages
18–19), and then set communication settings (See
pages 46–49), then perform the following operation.
• To use this function, we recommend setting “Auto
Power Off” to “No”. (See page 43.)
Before accessing DLNA servers:
• DLNA servers and this player must be connected to the
same local area network. Specify the settings required
for connecting this player to the local area network.
• DLNA servers must be turned on.
• When a PC running DLNA server software or other
DLNA-compatible devices are connected to this player,
some setting changes of software or other devices may
be required.
4 Press a/b to select a DLNA server which you
want to access, then press ENTER or d.
• The folder list or file list of the DLNA server which
you accessed is displayed.
• The previous screen appears when j
is pressed.
• Before using this function, please read “Network Service
Disclaimer” (page 69).
5 Press a/b to select the folder or file which you
want to access, then press ENTER.
• When you select a folder, the file list of the folder is
displayed. Press a/b to select the file which you
want to play, then press ENTER.
• Please refer to the operating instructions for the
software or devices for more information.
Playback by selecting a file list
• Playback starts.
1 Press a/b to select Video/Music/Picture, then
press d or ENTER.
Root
2 Press a/b to select “Home Network” in the sub
window.
Folder1
Folder2
Video
BD-Video
USB
Video01.divx
Video02.divx
Video03.divx
Video04.divx
1/ALL 40 files and folders
Music
Picture
e-Contents
Settings
Home Network
• For operation during playback, refer to pages
35–36.
6 Press c to stop playback.
Sub Window
• The file list reappears.
• The previous screen appears when j
is pressed.
7 Press EXIT or HOME to exit playback.
• The HOME screen reappears.
34
Playback Functions
Fast Forward/Reverse (Search)
Pause/Frame Advance Playback
BD VIDEO
DVD VIDEO
AUDIO CD
BD-R
BD-RE
BD VIDEO
BD-R
BD-RE
DVD-R DVD-RW
DVD VIDEO
DVD-R DVD-RW
The Pause function is enabled when b is
pressed during playback. (If you are playing back
an audio CD, audio data [MP3 files] or still images
[JPEG files], these will also pause.)
The Fast Forward/Reverse function is enabled when
d or e is pressed during playback.
Example: When e is pressed
• The search speed will change each time you press the
button.
The Frame Advance Playback function is enabled
when g is pressed during pause.
• Frame Advance Playback may not function properly
with discs other than DVD-RW/R (VR format).
When playing back a DVD
• You cannot perform Fast Forward/Fast Reverse from
one title and continue to another title (except when
playing audio CDs). At the end or beginning of the title,
Fast Forward/Fast Reverse will be cancelled and normal
playback will automatically resume.
NOTE
• Some BD/DVD Video discs are not compatible with
Pause/Frame Advance Playback.
• Frame Advance/Reverse Playback can be performed
for DVD discs by pressing g or
f during pause.
• Frame Reverse Playback cannot be performed for DivX
video.
NOTE
NOTE
• Subtitles are not played back with BD/DVD video discs
during Fast Forward and Fast Reverse.
• Some operations in the following playback functions
cannot be performed depending on the specifications of
the disc.
Skipping to the Next or the Start of
the Current Chapter (Track/Title)
Slow Playback (Forward/Reverse)
BD VIDEO
DVD VIDEO
AUDIO CD
BD-R
DVD-R DVD-RW
CD-R CD-RW
BD-RE
BD VIDEO
BD-R
BD-RE
DVD VIDEO
DVD-R DVD-RW
USB
The Slow Playback (Forward/Reverse) function is
enabled when g or f is
pressed for more than 2 seconds during pause.
Press a to return to normal playback.
The Skipping (to the beginning of a chapter, track
or title) function is enabled when f or
g is pressed during playback.
NOTE
• This doesn’t work for audio CDs.
• You cannot perform Slow Playback between titles. At
the end of the title, Slow Playback will be cancelled and
normal playback will automatically resume.
• Reverse Slow Playback cannot be performed for BD
video and DVD discs in AVCHD format.
• Reverse Slow Playback cannot be performed for DivX
video.
35
Playback Functions
Skip Search
NOTE
Partial Repeat Playback (Repeat
Playback of a Specified Part)
• Press j to cancel without setting the type
of Repeat Playback.
BD VIDEO
BD-R
BD-RE
• For Audio CD, you can select “Playing Disc”, “Playing
Track” and “Specify The Part” as Repeat Playback
options.
DVD VIDEO
DVD-R DVD-RW
DVD VIDEO
DVD-R DVD-RW
AUDIO CD
Playback skips 30 seconds ahead when SKIP
SEARCH is pressed during playback.
• Repeat Playback cannot be performed for DivX video.
1 Press REPEAT during playback.
4 Press ENTER.
2 Press a/b to select “Scene Selection”, then
Replay
Example: Repeat playback of a title (TITLE)
press ENTER.
• “Set Start Point” displays.
BD VIDEO
BD-R
BD-RE
BD-VIDEO
Playback Title
DVD VIDEO
DVD-R DVD-RW
1/3
5 25/
Playback Chapter
00:20:30
2 English
1
Playback jumps back 10 seconds when REPLAY is
pressed during playback.
Scene Selection
Set Start Point
3 Press ENTER at the scene where you want to
set the start point.
1 DTS
On Title Repeat
Repeat Playback of a Title or
Chapter (Repeat Playback)
• “Set End Point” displays.
4 Press ENTER at the scene where you want to
BD VIDEO
DVD VIDEO
AUDIO CD
BD-R
BD-RE
set the end point.
• You can press e to fast forward to the
scene where you want to set the end point. When
you reach the desired scene, simply press a
and then ENTER to set the end point. To cancel
Repeat Playback, press REPEAT-OFF or REPEAT.
DVD-R DVD-RW
On Title Repeat
• To exit the Function Control screen, press
j or FUNCTION.
1 Play back the title or chapter you want to repeat.
5 Press REPEAT-OFF or REPEAT to return to
2 Press REPEAT.
NOTE
normal playback.
3 Press a/b to select the type of Repeat
• Press g, the Repeat Playback is
cancelled and the next chapter being play back.
• Press f once, the Repeat Playback is
cancelled and the player returns to the start of current
chapter (track).
• If you press f again (within about 5
seconds) the player will skip to the beginning of the
previous chapter (track).
NOTE
Playback.
• Playback Title: Repeats the title currently being
played back.
• “Scene Selection” operation is not available for BD
video.
• Playback Chapter: Repeats the chapter currently
being played back.
• Scene Selection: Repeats the specified scene of
title or chapter.
• For Partial Repeat Playback, set the start and end
points within the same title.
• Repeat Playback may be forbidden depending on the
disc.
• Partial Repeat Playback may not work in multi-angle
scenes.
Playback Title
Playback Chapter
Scene Selection
• If you press DISPLAY, you can confirm the Repeat
Playback status.
36
Playback Functions
• “–” is displayed if a disc is recorded with only one angle.
Displaying the Audio Information
Switching Subtitles
BD VIDEO DVD VIDEO
You can display the audio information on the disc
currently being played back by pressing AUDIO.
The displayed contents vary depending on the disc.
1
If subtitles are provided in multiple languages, you
can switch between them.
BD VIDEO DVD VIDEO
Press SUBTITLE during playback.
To return to the previous angle, press ANGLE to
cycle through the angles until you return to the
original angle.
The audio channel currently being played back will
be displayed.
If multiple audio channels are recorded, you can
switch the audio channel by pressing AUDIO.
• The display indicates the subtitle number currently
being played back, and the subtitles appear.
Each time SUBTITLE is pressed, the subtitles change.
• “–” is displayed if a disc has no subtitles.
• You can also select “Off”.
NOTE
• The displayed items vary depending on the disc.
• If you access the Function Control screen during
playback of a BD/DVD video, it may be impossible to
operate the BD/DVD video playback. In cases like this,
close the Function Control screen.
• The operation of angles differs according to each disc.
You may need to refer to the operation manual of the
disc.
DVD-RW DVD-R
NOTE
When a recorded broadcast with stereo or
monaural audio is played back:
“Stereo” is displayed. (Audio cannot be switched.)
• Settings for subtitles can also be changed in the
Function Control screen (Page 38).
• The operation of subtitles differs according to each disc.
You may need to refer to the operation manual of the
disc.
• The display for subtitle information automatically
disappears after 5 seconds.
NOTE
• When you play a program recorded in stereo or
monaural, and if you are listening to the Bitstream
sound via the digital output jack, you cannot select the
audio channel. Set “Audio Out” to “PCM” (page 42).
• Settings for audio can also be changed in the Function
Control screen (Page 38).
• The operation of audio differs according to each disc.
You may need to refer to the operation manual of the
disc.
• The display for angle information automatically
disappears after 5 seconds.
Displaying the Angle Mark
Switching the Angle
BD VIDEO DVD VIDEO
BD VIDEO DVD VIDEO
You can change settings so that Angle Mark appears
in the right bottom part of the screen when multiple
angles are recorded. The settings can be changed
in “Settings” – “Playback Setting” – “Angle Mark
Display” (Page 44).
If multiple angles are recorded, you can switch
between them.
• The display for audio information automatically
disappears after 5 seconds.
Press ANGLE during playback.
• The display indicates the angle number currently being
played back. Each time you press ANGLE, the angle
switches.
37
Settings During Playback
3 Operation guide display
Provides help on remote control button operations.
NOTE
Function Control
• If “– –” is displayed for an option like title number or
subtitles, the disc has no titles or subtitles which can be
selected.
• The displayed items vary depending on the disc.
• If you access the Function Control screen during
playback of a BD/DVD video, it may be impossible to
operate the BD/DVD video playback. In cases like this,
close the Function Control screen.
BD VIDEO
DVD VIDEO
AUDIO CD
BD-R
BD-RE
Function control operation
procedure
DVD-R DVD-RW
This allows you to adjust various settings at once,
like subtitles, angle settings and the title selection
for Direct Playback. You can adjust the video and
audio to suit your preferences. The operations are
the same for BD and DVD.
Function Control screen
1 Press FUNCTION during playback.
• The Function Control screen is displayed on the TV.
BD-VIDEO
1
2 Press a/b to select the desired setting, then
1/3
5 25/
00:20:30
2 English
press ENTER.
• For a description of each setting, see “Functions
which can be set” (Page 39).
2
1
1 DTS
Off
BD-VIDEO
1/3
5 25/
00:20:30
2 English
1
1 DTS
Off
ENTER
Select
Enter
Return
EXIT
Exit
3
1 Playback status display
Shows the operation status and the disc type.
2 Setting items
Selects a title (or track) or chapter for playback, or
performs video/audio settings.
3 Press a/b/c/d to set, then press ENTER.
• Operations vary depending on the setting. Follow
the operation instructions on the screen.
4 Press j or FUNCTION to close the
• Title/Track Number (Direct Title/Track Skip)
• Chapter Number (Direct Chapter Skip)
• Playback Elapsed Time (Direct Time Skip)
• Subtitle Language
Function Control screen.
• Angle Number
• Audio
• Repeat
38
Settings During Playback
Subtitle Language
Functions which can be set
• Shows the currently selected subtitle language. If
subtitles are provided in other languages, you can
switch to your preferred language.
Title/Track Number (Direct Title/Track Skip)
• Shows the title number being played back (or track
number when playing back an audio CD). You can skip
to the start of the title (or track).
• To skip to the start of a selected title (or track), press
the Number buttons to enter the title (or track) number
when this option is highlighted.
Angle Number
• Shows the currently selected angle number. If the video
is recorded with multiple angles, you can switch the
angle.
Audio
Chapter Number (Direct Chapter Skip)
• Shows the chapter number being played back. You can
skip to the start of the chapter.
• Shows the currently selected type of audio. You can
select the desired type of audio.
• To skip to the start of a selected chapter, press the
Number buttons to enter the chapter number when this
option is highlighted.
Repeat
• The current Title (or Chapter) or partial segments can
be repeatedly played back. Repeat Playback is also
possible with the REPEAT button on the remote control.
Playback Elapsed Time (Direct Time Skip)
NOTE
• Shows the time elapsed from the beginning of the
current disc title (or track). This lets you skip to a
specific time.
• These functions may not work with all discs.
• Press c/d to select the Hour, Minute or Second, then
press a/b or the Number buttons to set the time.
Press ENTER to start playback at the set time.
NOTE
• ENTER button under the Cover: Enters the input
number.
• CLEAR button under the Cover: Clears the input
number.
39
Settings
SETTINGS
Common operations
The “menu” enables various audio/visual settings
and adjustments on the functions using the remote
control unit. You need to call up the On Screen
Display to perform settings for this player. The
following is the explanation for the basic operations
of the “menu”.
Home screen display
Press a/b to select “Settings”, then press d or ENTER.
HOME
Audio Video Settings
Smart Settings
AQUOS LINK
Playback Setting
On Screen Language
Communication Setup
Version
USB Memory Management
Software Update Settings
System
Video
Music
Picture
e-Contents
Settings
Example: Setting “AQUOS LINK”
Select
ENTER
EXIT
Enter
Return
Exit
Select a menu item
Press a/b to select “AQUOS LINK”, then press d or ENTER.
HOME
Audio Video Settings
Smart Settings
Video
AQUOS LINK
Music
Playback Setting
On Screen Language
Communication Setup
Version
USB Memory Management
Software Update Settings
System
Picture
e-Contents
Settings
Select
ENTER
EXIT
Enter
Return
Exit
Select the next item
Press a/b to select the desired item, then press ENTER.
Press j to return to the previous “menu” page.
Exit the menu screen
Press HOME or EXIT to exit.
40
SETTINGS
5 Press c/d to select the parental control level
for DVD VIDEO, BD-ROM, and then select the
country code. Press ENTER after making each
selection.
Basic Operation for Playback
Setting
Example: Setting “Parental Control” under “Playback
Setting”
Parental Control
Disc Language
Angle Mark Display
Password Setting
BD Internet Access
3D Mode
1 Press a/b to select “Settings”, then press d or
ENTER.
2 Press a/b to select “Playback Setting”, then
press d or ENTER.
Level 3
0
3D Notice
3 Press a/b to select “Parental Control”, then
press d or ENTER.
• When you operate this Player for the first time,
the password setting screen will be displayed.
See “When setting the password for the first time”
below.
USA
6 Press HOME or EXIT to exit.
4 Enter your 4-digit password.
• You cannot move to the next setting screen until
you can input the correct password.
When setting the password for the first time.
1 To set the password for the first time, press
a/b to select “Yes” to enter the password
setting menu, then press d or ENTER.
2 Enter a 4-digit number for the password, then
the same 4-digit number for confirmation.
3 Press ENTER to complete the password setting
procedure and move to the next setting screen.
41
SETTINGS
2 This sets the audio output mode for DIGITAL
AUDIO OUT (OPTICAL terminal) when selecting
“Digital Output”.
Audio Out
Audio Video Settings
You can set the audio output when connecting to
SURROUND equipment.
HDMI Video Out
Item
1 This sets the audio output connected to
Bitstream:
This sets the resolution of the video output for the
HDMI terminal of this player.
SURROUND equipment.
• Select this when connecting to SURROUND
equipment with a built-in decoder for DOLBY
DIGITAL, etc.
• Setting to Bitstream will output each audio signal by
Bitstream.
Normally set to “Auto” (factory preset value).
Item
Item
HDMI Output: Select this when you connect using
HDMI OUT terminal.
Digital Output: Select this when you connect using
DIGITAL AUDIO OUT terminal (OPTICAL).
Auto, 1080p, 1080i, 720p, 480p
PCM:
• Select this when connecting to 2 channel stereo audio
equipment.
• Setting to PCM will output by converting each audio
signal into PCM 2 channel audio signal.
NOTE
• When the BD player is connected to a 1080p 24Hz
compatible TV and the “HDMI Video Out” is set to
“Auto”, 1080p 24Hz will automatically be displayed
when compatible discs are played back.
2 You can set the audio output mode for each
output terminal.
NOTE
1 This sets the audio output mode for HDMI OUT
• See page 54 for information on output of audio formats.
terminal when selecting “HDMI Output”.
Secondary Audio
NOTE
This toggles the clicking sound on the menu and
audio with secondary video in picture in picture
mode for BD-Video.
• Select “Off” when enjoying the high quality sounds of
BD-Video.
• When the secondary audio is set to “On”, PCM is
automatically selected as the audio output mode.
Item
Bitstream:
Item
• Select this when connecting to HDMI equipment with
a built-in decoder for DOLBY DIGITAL, etc.
• Setting to Bitstream will output each audio signal by
Bitstream.
On, Off
PCM (Surround):
• Select this when connecting to multi-channel HDMI
equipment.
• Setting to PCM (Surround) will output by LINEAR
PCM by decoding audio signals recorded in each
audio output mode such as DOLBY DIGITAL, DTS.
42
SETTINGS
Dynamic Range Control
Control Panel
Smart Settings
This lets you adjust the range between the loudest
and softest sounds (dynamic range) for playback
at average volume. Use this when it is hard to hear
dialog.
This lets you set display of the control panel on the
TV screen to on or off.
Quick Start
This turns the Quick Start function on and off.
When the Quick Start function is on:
• The startup time of the Player is reduced.
• However, power consumption will increase.
When the Quick Start function is off:
• The player will enter the low power consumption mode
when in standby condition.
Item
Yes, No
Item
Normal: The same audio output range is played as the
original recorded audio output range.
Shift*: When Dolby Digital audio is played back, the
dynamic range of the audio is adjusted so that the
dialog portion can be heard easily. (If the audio
sounds abnormal, set to “Normal”.)
AQUOS LINK
This lets you set the Player to receive the control
signal from the AQUOS LINK remote control via the
HDMI cable.
Item
Yes, No
Auto: When you play back audio in the Dolby TrueHD
format, the dynamic range is automatically adjusted.
Item
Yes, No
NOTE
Lower the audio volume before setting. If you do not do
so, the speakers may emit a loud sound or excessive
output may be applied to the speakers.
*
• When “Quick Start” is set to “Yes”, the Player requires
some time to turn off.
NOTE
• For details, refer to the operation manual of TV.
SUPER PICTURE
Auto Power Off
This enhances the quality of video streaming images
with pixel by pixel processing technology.
This sets the Player so that power is automatically
shut off if playback is stopped and you do not
perform any operations for about 10 minutes.
Item
Item
On, Off
Yes, No
Front Display/LED
If you feel that the indicators on the player’s front
display are too bright when watching movies, you
can turn them off except for the POWER (ON/
STANDBY) indicator.
Item
On, Off
43
SETTINGS
Disc Language (Disc Priority Language)
Password Setting
Playback Setting
This lets you select the language for subtitles, audio
and menus displayed on the screen.
This sets the password for setting or changing the
Parental Control Level.
Parental Control
This lets you set the Parental Control depending
on the disc content. The available Parental Control
Levels are shown below.
Item (Subtitle)
Item
Select the subtitle language you want to display.
Yes: Enter the 4-digit number.
No
The 4-digit password number needs to be entered
before the Parental Control Levels and the Country
Code are set. The Parental Control Levels and the
Country Code cannot be set if a password has not
been created or the password is not entered.
• Select the rating level appropriate for the age of the
user.
Item (Audio)
NOTE
Select the audio language you want to hear.
• When you forget the password, you can reset the
current password using “System Reset” under
“Settings”. (See page 45.)
Item (Menu)
Select the menu language you want to display.
• You can also set the new password if desired.
NOTE
Item (Parental control level for DVD-video)
BD Internet Access
• When “Auto” is selected, the priority language of the
disc will be played back.
8 and Off: All DVD-video can be played.
1–7: Prohibits play of DVD-video with corresponding
ratings recorded on them.
This allows you to set access restriction to BD-LIVE
contents.
Angle Mark Display
Item
Item (Parental control level for BD-video)
This lets you turn the Angle Mark Display on or off
when BD/DVD video recorded with multiple angles
is played back. (The Angle Mark is displayed in the
lower right screen.)
Permit: Allows all BD-LIVE discs.
Limit: Allows only discs with owner certification.
Prohibit: Prohibits all BD-LIVE discs.
No Limit: All BD-video can be played.
0–99 year(s): Prohibits play of BD-video with
corresponding ratings recorded on them.
NOTE
Item (Country code)
Item
• The available functions differ depending on the disc.
• Regarding playback method of BD-LIVE contents,
etc., perform the operations in accordance with the
instructions in the BD disc manual.
• To enjoy BD-LIVE functions, perform the broadband
Internet connection (pages 18–19) and communication
settings (pages 46–49).
Select the country code.
The ratings differ according to the country.
Yes, No
NOTE
• Refer to “Basic Operation for Playback Setting” on page
41 for details.
44
SETTINGS
3D Mode
DivX(R) Deregistration
Version
This sets output of 3D images.
You can deactivate your DivX information on the
player.
When you select “Version”, the system software
version and Netflix ESN are displayed.
To view 3D images, playback of 3D content (3D BD
video) is necessary with a 3D compatible TV and 3D
glasses in addition to this player.
Item
System
Yes, No
Item
System Reset
NOTE
Auto: Video signals are output as 3D when 3D content
(3D BD video) is played or as 2D when 2D content is
played.
You can reset all settings to the factory presets.
2D: Even if 3D content (3D BD video) is played, video
signals are output as 2D at all times.
Item
VUDU Deactivate
Reset, Not Reset
You can deactivate your VUDU information on the
player.
CAUTION
Netflix Deactivate
• When viewing 3D images, viewing for a long period
of time or lying on your back may cause eye strain
and discomfort. In addition, 3D images may affect the
eyesight of young children/infants, so keep them from
viewing the images.
Item
You can deactivate your Netflix information on the
player.
Yes, No
Item
Yes, No
3D Notice
DivX(R) Registration
This sets whether or not a notice is displayed (“Yes”
or “No”) on the connected TV every time 3D content
(3D BD video) is played.
The DivX registration code is displayed.
Item
Item
Yes, No
Yes, No
NOTE
On Screen Language
You can set the language you want to display on the
screen.
Item
English, Español, Français
45
SETTINGS
4 Press a/b to select “Change”, then press
Communication Setup
Sets whether “Cable” or “Wireless”
is used for the network connection
ENTER.
This allows you to perform and/or change the
communication settings and select the type of
Internet connection from Cable or Wireless. This
setting is required to use BD-LIVE functions, video
on-demand services (e-Contents), home networks
and software updates that connect to the Internet.
Current Ethernet setup info.
1 Press a/b to select “Settings”, then press d or
IP Address : Auto Setup
Netmask : Auto Setup
ENTER.
2 Press a/b to select “Communication Setup”,
Gateway
DNS
: Auto Setup
: Auto Setup
then press d or ENTER.
3 Press a/b to select “Cable/Wireless Select”,
NOTE
then press d or ENTER.
Change
Initialize
• Make sure that the LAN cable or the wireless LAN
adapter is connected to this player and make sure that
the wireless router/access point is connected to the
Internet if using the wireless LAN adapter. (See pages
18–19.)
• For manually performing the setting, the following
information of the connected router or modem is
required. Confirm the information prior to the setting.
− IP address, netmask, gateway, DNS address
4 Press a/b to select “Cable” or “Wireless”, then
press ENTER.
• If selecting “Cable”, follow the [When selecting
Cable] directions on this page, then go to step 3.
• If selecting “Wireless”, follow the [When selecting
Wireless] directions on the next page, then go to
step 3.
• For initializing the current setting, select “Initialize”,
then press ENTER.
5 For setting the IP address, press c/d to select
“Yes” or “No”, then press ENTER.
NOTE
Do you obtain the IP address
automatically?
• When selecting “Wireless” when the wireless LAN
adapter is not inserted, “Wireless LAN adapter is not
inserted” appears on the screen.
Yes
No
IP Address
Netmask
Gateway
When selecting Cable
Next
1 Press a/b to select “Settings”, then press d or
ENTER.
• If selecting “Yes”: The IP address is automatically
obtained.
• If selecting “No”: The IP address, netmask and
gateway are manually entered using the screen for
inputting characters. (See page 49.)
Regarding each of the setup values, confirm the
specifications of your broadband router.
2 Press a/b to select “Communication Setup”,
then press d or ENTER.
3 Press a/b to select “Ethernet Setup (Cable)”,
then press d or ENTER.
46
SETTINGS
6 Select “Next”, then press ENTER.
5 The player scans all of the available access
points and displays the points with the “Other
Network” selection bar on the screen.
When selecting Wireless
• If selecting “Yes” in the step 5, go to the step 8.
7 Enter your DNS address.
CAUTION
• During searching access point(s), “Accessing...”
appears on the screen.
• We recommend writing down the MAC address of
the connected wireless LAN adapter in this operation
manual (page 48) and keeping it in a safe place. The
MAC address is labeled on the adapter or displayed on
the “Current Ethernet setup info.” screen (See step 4
below).
• When performing the wireless communication setup,
security information for the wireless router/access
point (WEP, WPA or WPA2 key) is required. Check your
wireless router/access point’s information prior to setup.
Enter your DNS address.
• Up to 6 items (5 access points and the “Other
Network” selection bar) are displayed on the screen.
• When there are six or more items retrieved, display
the next screen by selecting “Next”, then pressing
ENTER. (The “Other Network” selection bar is
always displayed last.) When no available access
points are retrieved, only the “Other Network”
selection bar is displayed on the screen.
Primary
Secondary
Next
• The primary and secondary DNS addresses are
entered using the screen for inputting characters.
(See page 49.)
Regarding each of the setup values, confirm the
specifications of your broadband router.
6 Press a/b to select “desired access point” or
“Other Network”, then press ENTER.
• For access points which are set to hide the SSID
using the wireless router, select “Other Network” to
set the access point.
NOTE
• Wireless communication setup cannot be performed
when the wireless LAN adapter is not inserted.
• Before this player can access the Internet wirelessly,
setup of a wireless router/access point is required.
8 Select “Next”, then press ENTER.
9 For testing the connection to the Internet, after
confirming the settings, press a/b to select
“Test”, then press ENTER.
Select the access point.
1 Press a/b to select “Settings”, then press d or
XXXXXXXXXXXX
YYYYYYYYYYYY
Other Network
• “Test” is available only when setting to obtain the IP
address automatically. “Test” cannot be selected if
the IP address has not been obtained automatically.
ENTER.
2 Press a/b to select “Communication Setup”,
then press d or ENTER.
Confirm the current setting.
3 Press a/b to select “Ethernet Setup
• If selecting “desired access point”, go to step 9.
• If selecting “Other Network”, go to the next step.
(Wireless)”, then press d or ENTER.
IP Address : xxx xxx xxx xxx
4 Press a/b to select “Change”, then press
Netmask
Gateway
: xxx xxx xxx xxx
: xxx xxx xxx xxx
ENTER.
DNS Address : xxx xxx xxx xxx
xxx xxx xxx xxx
MAC Address : xx xx xx xx xx xx
Current Ethernet setup info.
MAC Address : xx xx xx xx xx xx
Access Point : Not Selected
IP Address : Auto Setup
Test
Complete
Netmask
Gateway
DNS
: Auto Setup
: Auto Setup
: Auto Setup
• As a result of the test, if the Internet connection
fails, enter the setup values manually.
10 Press a/b to select “Complete”, then press
Change
Initialize
ENTER.
11 Press HOME or EXIT to return to the HOME
screen.
• For initializing the current setting, select “Initialize”,
• To perform other settings, press j.
then press ENTER.
(Continued on the next page)
47
SETTINGS
7 Press ENTER, then enter the access point
name.
11 Select “Next”, then press ENTER.
Information on MAC addresses
12 For testing after confirming the settings, select
• The access point name is manually entered using
the screen for inputting characters. (See page 49.)
“Test”, then press ENTER.
A MAC address is a unique ID number for
network equipment. A MAC address is necessary
for MAC address filtering on the wireless router/
access point.
• If the test has failed, an error message appears.
Retry to perform the settings after checking that the
connection (page 19) is performed properly.
Enter the access point name.
Access Point:
Confirm your setting.
Before the wireless communication setup is
performed, we recommend writing down the MAC
address of the connected wireless LAN adapter
and keeping it in a safe place. The MAC address
is labeled on the adapter. (The MAC address is
displayed on the “Current Ethernet setup info.”
screen when wireless communication is set (See
step 4 of page 47).)
Access Point: XXXXXXXXXXXX
Security key: XXXXXXXXXXXX
Next
Test
8 Select “Next”, then press ENTER.
9 Press a/b to select your appropriate security
13 Follow steps 5–11 of “When selecting Cable”
on page 46 to complete the network connection
settings.
key, then press ENTER.
• When selecting WPA/WPA2, selectable security
keys are PSK/TKIP and PSK/AES.
MAC address
Select the security key.
OPEN
WEP
WPA-PSK(AES)
WPA-PSK(TKIP)
WPA2-PSK(AES)
WPA2-PSK(TKIP)
10 Press ENTER, then enter the security key code.
• Enter the exact same security key which has been
set in the wireless router.
• The security key code is manually entered using the
screen for inputting characters. (See page 49.)
Enter the security key.
Security key:
Next
48
SETTINGS
5 Press D (Yellow) (Complete) to fix the numbers
NOTE
The operation procedure for
inputting characters manually
which have been input.
• Press j (Del.Char.) to delete a number/
character you have input.
• To change a number/character you have input, press B
(Green) (Left) or C (Blue) (Right) to select the number/
character you want to change, and press j
(Del.Char.). Then, press c/d to select a new number/
character you want to input, and press ENTER.
IP Address
Netmask
Gateway
123
NOTE
• Numeric characters such as IP address can be entered
on the input screen either by selecting each of the
characters in the “Numeric” mode or using the Number
buttons on the remote control.
6 Repeat step 1 to 5 to finish inputting all the
required characters.
IP Address
Netmask
Gateway
123
Input character list
1ABC (Alphabet/
numeric character)
Num.
ABC
DEF
GHI
JKL
MNO
PQRS
DEF
TUV
WXYZ
Spc.
1 Press ENTER at the boxes in which characters
are to be entered, and the input screen will
appear.
Num. 1 2 3 4 5 6 7 8 9 0 ABC
a b c A B C
j k l J K L
d e f D E F
GHI
g h i G H I
JKL
TUV
MNO m n o M N O
PQRS p q r s P Q R S
t u v T U V
WXYZ w x y z W X Y Z
Numeric
Edit
1
2
3
4
5
6
7
8
9
0
Spc.
(space)
Numeric
Sign
1 2 3 4 5 6 7 8 9 0
Selected by pressing Selected by pressing
a/b c/d
@ . , :
@ . , :
; _ - \
$ % ! ? & # + *
= / | ˜
“ ‘ ˆ `
( ) < >
[ ]{ }
Spc.
2 Press a/b to select the desired input mode.
3 Press c/d to select a number/character, then
@ . , :
; _ - \
= / | ˜
; _ - \
= / | ˜
$ % ! ? $ % ! ?
press ENTER.
& # + * & # + *
( ) < > ) <
“ ‘ ˆ `
Spc.
“ ‘ ˆ `
(space)
4 Repeat the step 3 to display all of the desired
(
>
[ ]{ }
[
]
{
}
characters/numbers in the input field.
Example: The screen for inputting numeric characters
Edit
Cancel
Left
Right
Complete
Del.Char.
The same operation as the colored buttons and j can be performed by selecting
each of the items and pressing ENTER.
“Del.Char.” stands for deleting characters.
123
Numeric
Edit
1
2
3
4
5
6
7
8
9
0
NOTE
• When performing “Ethernet Setup (Cable)”, only “Numeric” and “Edit” are displayed.
49
SETTINGS
When you insert or remove a USB memory device,
be sure to turn the main power off and make sure
that “Quick Start” is set to “No” (See page 43).
5 Press a/b to select “Erase” or “Format”, then
Before using the USB memory device
press ENTER.
CAUTION:
Erase: Deletes only BD-VIDEO data written on the
USB memory device such as BD-LIVE data.
Format: Be aware that all data including BD-VIDEO
data and software update data will be deleted.
• Do not remove the USB memory device or unplug
the AC cord while the operations for “USB Memory
Management” or “Software Update Settings (Manual
Update from USB memory device)” are being
performed.
1 Insert the USB memory device into the USB
terminal on this player.
• When the wireless LAN adapter is not inserted
into the USB1 terminal on the rear of the player, it
is recommended that the USB memory device be
connected to the USB1 terminal.
• If you want to delete only the unneeded software
update data after the software is updated, delete
the data on the USB memory device using a PC.
• Do not use a USB extension cable when connecting
a USB memory device to the USB1 or USB2 terminal
on the player.
− Using a USB extension cable may prevent the
player from performing correctly.
NOTE
• A USB memory device can be used with either the
USB1 or USB2 terminal. When two USB memory
devices are connected to both terminals at the same
time, in certain situations the USB1 terminal may give
priority to Local Storage and “Erase” and “Format” are
not available for the USB memory device connected to
the USB2 terminal.
Erase
Erases BD-VIDEO data on USB memory.
NOTE:
• SHARP cannot guarantee that all brands’ USB
memory devices will operate with this player.
• Only USB memory devices formatted with FAT 32/16
are compatible.
Format
Erase all contents on USB memory
including protected contents.
When formatting a USB memory device using a PC,
perform the following settings.
Format File System: FAT32
Rear
6 Press a/b to select “Yes”, then press ENTER.
• A confirmation message is displayed. Check that
the correct USB memory device is displayed, and
then continue.
Allocation Unit Size: Default Allocation Size
USB1 terminal
USB Memory Management
7 Start the process.
• The screen for the current operation will display.
The following instructions explain how to delete data
such as the Virtual Package data and the BD-LIVE
data in a USB memory device.
USB memory device
Complete
OK
Front
8 Press ENTER.
9 Press HOME or EXIT to exit.
USB memory
device
USB2 terminal
NOTE
• Data which has been saved to the player’s internal
memory (game score, etc.) will also be deleted.
2 Press ENTER to turn on the power.
3 Press a/b to select “Settings”, then press d or
ENTER.
4 Press a/b to select “USB Memory
Management”, then press d or ENTER.
• The “USB Memory Management” screen is
displayed.
• “No USB Memory” appears when no USB memory
is inserted.
50
SETTINGS
Update process
Software Update Settings
1 When this player is turned on, the Internet
connection starts automatically.
In this player, the software version can be updated
using either one of the following methods.
• Auto Update from Network
• “Accessing...” blinks on the screen.
• Manual Update from Network
• Manual Update from USB memory device
• The current version of this unit software and the
latest version of the update file on the network are
displayed when latest version of firmware has been
found.
Auto Update from Network
This function allows you to perform the update by
accessing an Internet connection automatically to
check if there is a new firmware version every time
the player is turned on.
When using this function, it is required to perform
the following settings in advance.
To update this player software with update file,
select “Yes”, and go to step 2.
Latest version of firmware has been found.
Firmware update is available.
Proceed with update?
Current Version :
Latest Version :
xxxxxxxxxx
yyyyyyyyyy
NOTE
Setup
If “Yes” will be selected, version update will start.
• Make sure that the LAN cable or the wireless LAN
adapter is connected to this player and make sure that
the wireless router/access point is connected to the
Internet if using the wireless LAN adapter. (See pages
18–19.)
• Make sure to perform the communication settings. (See
pages 46–49.)
1 Press a/b to select “Settings”, then press d or
Yes
No
ENTER.
2 Press a/b to select “Software Update
Settings”, then press d or ENTER.
• If the latest firmware version has been already
updated, nothing is displayed on the screen.
3 Press a/b to select “Auto Update Setting”,
then press d or ENTER.
• It may take time to access and download the update
depending on the Internet connection and other factors.
2 Press ENTER to start updating.
4 Press a/b to select “Yes”, then press ENTER.
• After this, an Internet connection will be made
automatically every time this player is turned on.
Downloading latest firmware…
Version : yyyyyyyyyy
CAUTION
• Do not remove the LAN cable or the wireless LAN
adapter or unplug the AC cord while downloading or
updating software.
30%
3 When the software is successfully updated, a
screen is displayed indicating that the update
process is completed.
• If the update has failed, an error message appears.
Retry the update after checking if the broadband
Internet connection (pages 18–19) and
communication settings (pages 46–49) are
performed properly.
4 Press POWER to turn off the player before using
again.
51
SETTINGS
6 Press ENTER to start updating.
1 Press a/b to select “Settings”, then press d or
Manual Update from Network
ENTER.
Downloading latest firmware…
Version : yyyyyyyyyy
2 Press a/b to select “Software Update
This function allows you to perform the update
operation by accessing an Internet connection
manually to check if there is a new firmware version.
Settings”, then press d or ENTER.
3 Press a/b to select “Manual Update”, then
press d or ENTER.
30%
NOTE
4 Press a/b to select “Network”, then press
• Make sure that the LAN cable or the wireless LAN
adapter is connected to this player and make sure that
the wireless router/access point is connected to the
Internet if using the wireless LAN adapter. (See pages
18–19.)
• Make sure to perform the communication settings. (See
pages 46–49.)
ENTER.
7 When the software is successfully updated, a
screen is displayed indicating that the update
process is completed.
5 During access to the network and checking the
latest version of firmware, “Accessing” blinks.
• The current version of this unit software and the
latest version of the update file on the network are
displayed when latest version of firmware has been
found.
• If the update has failed, an error message appears.
Retry the update after checking if the broadband
Internet connection (pages 18–19) and
communication settings (pages 46–49) are
performed properly.
• It may take time to access and download the update
depending on the Internet connection and other factors.
To update this player software with update file,
select “Yes”, and go to step 6.
8 Press POWER to turn off the player.
CAUTION
Latest version of firmware has been found.
Firmware update is available.
Proceed with update?
• Do not remove the LAN cable or the wireless LAN
adapter or unplug the AC cord while downloading or
updating software.
Manual Update from USB memory
device
Current Version :
Latest Version :
xxxxxxxxxx
yyyyyyyyyy
This function allows software updates by inserting
a USB memory device with the update file into the
USB1 or USB2 terminal on this player.
• When a software update is performed, the software
update data must be written onto the USB memory
device in advance using a PC.
• The USB memory device must be clear of all files
except software update data to allow new software
uploading.
If “Yes” will be selected, version update will start.
Yes
No
• If the Internet connection has failed, an error
message appears.
Retry the update after checking if the broadband
Internet connection (pages 18–19) and
communication settings (pages 46–49) are
performed properly.
To check for the availability of a software update,
you have any questions, please call 1-800-BE-
SHARP (800-237-4277).
• When software update data is released, copy the data
onto a USB memory device after downloading it to a
PC.
• For methods such as downloading and copying to a
USB memory device, carefully read the description
shown on the website before performing the operation.
52
SETTINGS
When you insert or remove a USB memory device,
be sure to turn the main power off and make sure
that “Quick Start” is set to “No” (See page 43).
7 Enter the 4-digit number using 0–9.
NOTE
• Only USB memory devices formatted with FAT 32/16 are
compatible.
When formatting a USB memory device using a PC,
perform the following settings.
Enter 4-digit password
1 Insert the USB memory device with the update
file into the USB1 or USB2 terminal on this
player.
Format File System: FAT32
Allocation Unit Size: Default Allocation Size
• Do not extract the firmware update file to any folders
other than the root directory on the USB memory
device. The firmware update file must be only one file
directly in the root directory.
• It is recommended that the USB memory device be
connected to the USB2 terminal on the front of the
player.
8 Press ENTER to start checking data in the USB
memory device.
NOTE
• A USB memory device can be used with either the
USB1 or USB2 terminal. When two USB memory
devices are connected to both terminals at the same
time, in certain situations the USB1 terminal may give
priority to Local Storage and the USB1 terminal cannot
be used for Software Update.
Insert USB memory device containing
the software update file.
OK
9 During the data checking, “Checking” blinks.
Now checking the data in USB memory device.
Checking
Front
• The current version of this unit software and the
version of the update file on the USB memory
device are displayed. To update this player software
with update file, select “Yes”, and press ENTER.
USB memory device
2 Press POWER to turn on the power.
3 Press a/b to select “Settings”, then press d or
ENTER.
Software update file is detected in the USB memory device.
Start update?
4 Press a/b to select “Software Update
Settings”, then press d or ENTER.
Current Ver. :
Update Ver. :
xxxxxxxxxx
yyyyyyyyyy
5 Press a/b to select “Manual Update”, then
press d or ENTER.
Yes
No
6 Press a/b to select “USB Memory”, then press
ENTER.
• If you have not yet set the password, go to step 7.
CAUTION
• Do not remove the USB memory device or unplug the
AC cord while the software is being updated.
(Continued on the next page)
53
SETTINGS
• If the USB memory device is not properly installed
10 Press ENTER to start updating.
• The screen becomes dark for a while until the
update screen can be displayed. Please wait for
the update screen to appear. Do not unplug the AC
cord.
11 When the software is successfully updated, a
screen is displayed indicating that the update
process is completed.
or the correct update file cannot be found on
the USB memory device, an error message is
displayed.
Check the file on the USB memory device, and then
reinsert the USB memory device correctly.
• If the update has failed, check the file in the USB
device and try Software Update again.
12 Press POWER to turn off the player.
• Delete unneeded software update data using a PC
after the software update process is completed.
The picture will temporarily go dark until
the software update display appears.
Wait several minutes and do not unplug the AC cord.
Software update file is not detected in the USB memory device.
Confirm that you have transferred the file
to the USB memory device and retry software update.
Confirm that you have inserted the USB memory device
into the correct device.
13 Remove the USB memory device.
OK
OK
Now updating
There is more than one software file
in the USB memory device.
Confirm that only the software update file is
in the USB memory device.
Do not unplug AC cord.
Update Version
*
yyyyyyyyyy
30%
OK
About Output of Audio Formats
HDMI
DIGITAL OUT
Maximum number of
Audio format
Dolby TrueHD
channels
PCM
7.1ch *3
5.1ch *3
7.1ch
Bitstream
PCM
2ch *2
2ch *2
2ch *2
2ch *2
2ch *2
2ch *2
2ch *2
2ch *2
Bitstream
5.1ch *1/*3
5.1ch *1/*3
5.1ch *1/*3/*6
5.1ch *1/*3
5.1ch *1/*3
5.1ch *1/*3
—
7.1ch (48kHz/96kHz)
5.1ch (192kHz)
7.1ch *4
5.1ch *4
7.1ch *4
7.1ch *4
5.1ch *4
7.1ch *4
—
Dolby Digital PLUS
7.1ch (48kHz)
DTS-HD Master Audio
7.1ch (48kHz/96kHz)
5.1ch (192kHz)
7.1ch *3
5.1ch *3/*5
7.1ch *3
7.1ch *3
5.1ch *3
DTS-HD High Resolution Audio
LPCM
7.1ch (48kHz/96kHz)
7.1ch (48kHz/96kHz)
5.1ch (192kHz)
—
—
I
Core only
J
K
L
M
M
N
Down mixed
When “Secondary Audio” is set to “On”, the audio is output as 48kHz.
When “Secondary Audio” is set to “On”, the audio is output as PCM.
When 5.1ch (192kHz), the audio output is downsampled to 96kHz.
When 2ch, the audio is output as 192kHz.
PCM outputs as 2ch during playback of video on demand content (page 55).
54
Streaming content
Playing back video on demand streaming content
In this player, you can enjoy a variety of video on
demand streaming content by connecting to the
Internet.
3 Follow the instruction on the screen.
Playing back YouTube content
4 To exit the screen, press EXIT.
This player can play back YouTube video content
streaming through the Internet.
• For more information about YouTube, see the YouTube
website using a PC (http://www.youtube.com).
Instantly Watching Movies from
Netflix
VOD content
Video
NOTE
Please check that the most current software
is loaded on this player by using the software
update function (See pages 51–54) or by visiting
check for a download of the newest software
version.
Music
• Some video content may not be played back with this
player.
• The actual functions which can be operated may differ
from the descriptions shown.
Picture
e-Contents
Settings
Operational buttons for playback control
This function allows you to enjoy Netflix through the
Internet.
Netflix is an online DVD and Blu-ray Disc rental
service, offering rental-by mail and streaming
instantly to Netflix unlimited members.
Item
VOD content
Netflix
• Instantly Watching Movies
Pause the video content. To resume
playing paused content, press
the playback controls.
on
VUDU
Skip to the previous video content on
the video list.
NOTE
• Enjoying Movies and Internet Application
• Disc playback and this function cannot be used at the
same time.
• As the registration process takes time, we recommend
setting “Auto Power Off” to “No” before starting the
registration. (See page 43.)
• The streaming quality (SD or HD) depends on the
network speed and original bit rate of the title.
netflix.com/help or login to your Netflix account and
click “Help” at the top of the page.
YouTube
Skip to the next video content on the
video list.
• Playing back YouTube video content streaming
NOTE
Play back all the video content on the
video list repeatedly.
• To enjoy this function, make a broadband Internet
connection to both your PC and this player (See pages
18–19), and then set communication settings (See
pages 46–49), then perform the following operation.
• To use this function, we recommend setting “Auto
Power Off” to “No” before starting the registration. (See
page 43.)
Switch the video quality to high
resolution.
Toggle the playback screen between
normal and full screen.
• Netflix is only available in the US.
Determine the point where you want to
play back a video content by pressing
c/d on the progress bar.
• Before using this function, please read “Network Service
Disclaimer” (page 69).
Progress bar
The buttons which can be used :
a/b/c/d / ENTER / a / b /
c / d / e / j /
EXIT
NOTE
Playing back
• To turn the playback controls on during full screen
display, press POP-UP MENU.
• To return to the main page screen, press TOP MENU/
TITLE LIST.
1 Press a/b to select “e-Contents”, then press
d or ENTER.
• Netflix is also available by pressing the NETFLIX
button on the remote control, and VUDU is also
available by pressing the VUDU button on the
remote control.
2 Press a/b to select the desired steaming
content, then press d or ENTER.
• The screen of the streaming content which you
select is displayed.
55
Playing back streaming content
VUDU Customer Care: When you need to talk live
with someone, contact VUDU Customer Care at
1-888-554-VUDU (8838) 7 a.m. to 8 p.m. Pacific, 7
days a week (except holidays).
NOTE
Enjoying Movies and Internet
Application with VUDU
• Your Internet connection is vital to your VUDU
experience. Please refer to the chart below for minimum
bandwidth requirements:
SD (DVD quality): 480p 1 Mbps to 2 Mbps
HD (HDTV quality): 720p 2.25 Mbps to 4.5 Mbps
HDX (BD quality): 1080p 4.5 Mbps to 9 Mbps
• VUDU Movies is only available in the U.S.
• For more information on VUDU, visit http://www.VUDU.
com.
You can enjoy moves and Internet applications with
VUDU.
VUDU Movies is the leading HD on-demand video
service. VUDU Movies is built into your BD Player
and utilizes your existing Internet connection
to deliver the highest quality on-demand video
available today.
Operational buttons during playback
Buttons
S
d
Description
Hold down to go in reverse.
Starts playback.
• Disc playback and this function cannot be used at the
same time.
Hold down to fast forward.
Playback stops.
V
H
Example
Troubleshooting - VUDU
Sets pauses and still pictures.
F
Pressing quickly once takes you to the
start of the chapter currently playing.
Each time you press it, you move back
to the start of the previous chapter.
T
VUDU cannot be accessed.
• If you are not able to access other network service (e.g.
BD-LIVE) from your device, but are not able to access
VUDU, please contact VUDU Customer Care at 1-888-
554-VUDU (8838).
Pressing quickly once takes you to the
start of the next chapter. Each time you
press it, you move ahead to the start of
the next chapter.
U
• If you are not able to access any network service (e.g.
BD-LIVE) from your device, please contact your device
manufacture for assistance.
VUDU Movies features:
The activation e-mail was not obtained.
• Check your junk or spam e-mail folders. If you are
unable to find the activation e-mail in the folders,
reconfirm the e-mail address you have entered, and
then try your account settings again.
• True 1080p HD, the only service to offer 1080p quality
video on-demand
• Over 16,000 titles available on-demand
• Over 3,000 titles available in HD, more than are available
anywhere else
• 5.1 surround sound, delivered through state-of-the-art
Dolby Digital Plus
• The latest Hollywood hits available the same day as
DVD
If you encounter any other issues during activation,
refer to the following online resources:
Detailed VUDU Manual: Available at
to all aspects of the revolutionary VUDU service
with easy-to-follow instructions.
• No subscription fees required
VUDU FAQ: To learn more about VUDU, visit the
Frequently Asked Questions at
56
Appendix
PC control of the Player
• This player can be controlled from a PC using the
RS-232C or IP.
IP Control Setup
Communication procedure
• Use a cross-type RS-232C cable, ETHERNET
cable (commercially available) or wireless LAN
USB adapter for the connections.
Send the control commands from the PC via the
RS-232C or IP.
This Player operates according to the received
command and sends a response message to the
PC.
Do not send multiple commands at the same time.
Wait until the PC receives the OK response before
sending the next command.
Make sure to send “A” with the carriage return and
confirm that “ERR” returns before operating.
NOTE
• This operation system should be used by a person who
is accustomed to using computers.
Communication conditions for IP
1 Press a/b to select “Settings”, then press d or
Connect to the player with the following settings
made for IP on the PC.
ENTER.
Command format
Eight ASCII codes eCR
2 Press a/b to select “Communication Setup”,
IP protocol:
TCP/IP
then press ENTER.
Host IP address:
Set the IP address on the player
menu
3 Press a/b to select “IP Control Setup”, then
C1 C2 C3 C4 P1 P2 P3 P4
press ENTER.
4 Press a/b to select “Change”, then press
Service:
None (Do not select Telnet or
SSH)
Command Parameter 4-digits
4-digits
Return code
ENTER.
Command 4-digits: Command. The text of four
characters.
5 To use IP Control, select “Enable”, then press
TCP port#:
Set a port number on the player
menu
ENTER.
Parameter 4-digits: Parameter 0 – 9, blank
6 Set the device name.
When you set your ID and password on the player
menu, you need to enter them as soon as you
connect to the player.
7 Set your login ID and password.
8 Set the port to use with IP Control.
9 Confirm the settings, then press “OK”.
Parameter
Input the parameter values, aligning left, and fill with
blank(s) for the remainder. (Be sure that four values
are input for the parameter.)
NOTE
• The connection will be cut off when there has been no
communication for 3 minutes.
When the input parameter is not within an adjustable
range, “ERR” returns. (Refer to “Response code
format”.)
Communication conditions for RS-232C
Set the RS-232C communication settings on the PC
to match the player’s communication conditions.
The player’s communication settings are as follows:
Response code format
Normal response
Baud rate:
Data length:
Parity bit:
9,600 bps
8 bits
O
K
Return code (0DH)
None
Problem response (communication error or
incorrect command)
Stop bit:
1 bit
Flow control:
None
E
R
R
Return code (0DH)
57
PC control of the Player
Command list
CONTROL ITEM
POWER ON*1
POWER OFF
PLAY
COMMAND
PARAMETER
CONTROL ITEM
COMMAND
PARAMETER
P
P
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
O
O
P
S
F
W
W
L
R
R
Y
P
D
V
N
K
N
T
1
0
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
PAUSE
D
D
D
D
B
M
S
I
P
E
U
J
S
T
_
_
_
_
1
1
1
1
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
OPEN/CLOSE
FUNCTION
F
N
E
N
R
V
P
C
P
M
D
N
V
STOP
T
REPEAT
R
D
N
W
P
FWD
W
E
DEVICE NAME*2
MODEL NAME*2
SOFTWARE VERSION*2
IP PROTOCOL VERSION*2
REV
R
T
TOP MENU
UP a
M
P
U
D
L
W
F
DOWN b
LEFT c
R
E
R
E
S
P
S
S
G
N
E
T
RIGHT d
ENTER
T
RETURN
T
EXIT
X
T
HOME
E
T
POP-UP MENU
SKIP K
SKIP L
M
K
K
N
B
F
I
The POWER ON command is available with IP control only when the power is off and Quick start
is ON.
J
This command is not available for RS-232C connections.
58
Troubleshooting
The following problems do not always suggest a defect or malfunction of this Player.
Refer to the problems and lists of possible solutions below before calling for service.
Power
Problem
Possible causes and solutions
The Player power cannot be turned on.
• Is the power cord firmly plugged into the AC outlet? (Page 20)
• When the power cord is plugged into an AC outlet, press and hold POWER on the Player until “
front panel display. Then, after the POWER indicator is lit, turn on the power. (Page 62)
” appears on the
• Press POWER after the POWER indicator turns on. (Page 21)
The Player power is turned off.
• Is “Auto Power Off” set to “Yes”? When “Auto Power Off” is set to “Yes”, the power will be automatically turned off after
10 continuous minutes of inactivity (no playback). (Page 43)
Basic Operation
Problem
Possible causes and solutions
The remote control does not work.
• Use the remote control within its operating range. (Page 20)
• Replace the batteries. (Page 20)
• Reset the remote control.
− Press and hold 1 (the number button) first and then POWER on the remote control together for more than 5 seconds.
Cannot operate the Player.
• Are you operating the Player within the specified operating temperature range? (Page 64)
Playback
Problem
Possible causes and solutions
The Player cannot play a disc.
• Take out the disc and clean it. (Page 13)
• Make sure that the disc is loaded properly (aligned in disc tray and label-side up). (Page 25)
• Make sure that region code on the disc matches that of this Player. (Page 9)
• Allow any condensation in or near the Player to dry. (Page 13)
• Check that the disc is recorded in the compatible TV system (PAL or NTSC).
• The Player cannot play back video which was not recorded normally. (Page 10)
• Proper playback may be impossible due to the state of the disc recording, a scratched, warped or dirty disc, the state of
the pick-up, or compatibility issues between this Player and the disc being used. (Pages 10, 13)
• When the recorded time of a disc is unusually short, playback may not be possible.
• BD-RE/R discs recorded in a format other than BDMV/BDAV cannot be played back. (Page 9)
The disc is automatically ejected after closing the disc
tray.
• Make sure that the disc is loaded properly (aligned in disc tray and label-side up). (Page 25)
• Take out the disc and clean it. (Page 13)
• Make sure that the disc is playable. (Page 9)
(Continued on the next page)
59
Troubleshooting
Playback (Continued)
Problem
Possible causes and solutions
Video stops.
• Has the Player been subjected to shock or impact? Are you using it in an unstable location? The Player will stop if it
senses shock or vibration.
The Player makes a snapping sound when starting
playback or loading a disc.
• The player may sometimes make a snapping sound when starting playback if it has not been operated in a while. These
sounds are not malfunctions of the player but are normal operating conditions.
Picture
Problem
Possible causes and solutions
No picture.
• Make sure that the cable is connected correctly. (Page 16)
• Make sure that the connected TV or the AV receiver is set to the correct input. (Pages 16–17)
• Take out the disc and clean it. (Page 13)
• Make sure that region code on the disc matches that of this Player. (Page 9)
• There is no picture from the HDMI output.
− Are the settings performed correctly? Please check the settings. (Page 42)
Screen freezes and operation buttons do not work.
Square noise (mosaic) appears on the screen.
• Turn off the power and turn on the power again.
• If the power is not turned off, perform a reset. (Page 62)
• Is the disc damaged or dirty? Check the condition of the disc. (Page 13)
• Blocks in images may be visible in scenes with rapid movement due to the characteristics of digital image compression
technology.
Audio is not output, or images are not played back
properly.
• The audio may not be output or the images may not be played back properly for some discs in which copyright-
protected contents are recorded (Pages 10–11).
3D images cannot be output to a TV.
• Is an HDMI cable used?
• Are a 3D compatible TV and 3D glasses used?
• Is a proper connection made between the HDMI OUT terminal of the player and the HDMI input terminal of the 3D
compatible TV? (Page 16)
• Is the 3D setting on this player correct? (Pages 23, 45)
• Are all devices (amplifier, AV receiver, etc.) between the TV and the player connected by HDMI and 3D compatible?
(Pages 16-17)
• Is the 3D setting on the TV correct?
• Is a 3D compatible BD disc being played back?
Noise appears on the screen.
• When you watch TV broadcasts with the power of this player turned on, noise may appear on the TV screen. In such
cases, turn off the power to this player or keep this player away from the TV.
60
Troubleshooting
Sound
Problem
Possible causes and solutions
No sound, or sound is distorted.
• If the volume of the TV or amplifier is set to minimum, turn the volume up.
• There is no sound during still mode, slow motion playback, fast forward and fast reverse. (Page 35)
• Check that the audio cable is connected correctly. (Page 17)
• Check that the cable plugs are clean.
• Take out the disc and clean it. (Page 13)
• Audio may not be output depending on the audio recording status, such as when audio other than an audio signal or
non-standard audio is recorded for the audio content of the disc. (Page 10)
Audio is not output, or images are not played back
properly.
• The audio may not be output or the images may not be played back properly for some discs in which copyright-
protected contents are recorded.
Network
Problem
Possible causes and solutions
Cannot connect to the Internet.
When the wired Internet connection is made
• Is the LAN cable connected properly? (Page 18)
• Is the wrong cable such as a modular cable used? Connect a LAN cable to the ETHERNET terminal. (Page 18)
• Is the power for the connected equipment, such as a broadband router or modem turned on?
• Is the broadband router and/or modem properly connected?
• Is the proper value(s) set in the network setting? Check “Communication Setup”. (Pages 46–49)
When the wireless Internet connection is made
• Is the wireless LAN adapter connected properly? (Page 19)
• Is the power for the connected equipment, such as a wireless router or access point turned on?
• Is the wireless router or access point properly connected?
• Are there any obstacles, such as physical structures (brick and concrete walls, etc.) and electronics (microwave, etc.)
between the wireless router/access point and the player? As this may cause interference with the wireless signal, make
sure to keep obstacles away.
• Is the proper value(s) set in the network setting? Check “Communication Setup”. (Pages 46–49)
Cannot download BD-LIVE contents.
• Is the LAN cable or the wireless LAN adapter connected properly? (Pages 18–19)
• Is the USB memory device properly connected? Check that the USB memory device is connected to the USB1 or USB2
terminal of this Player. (Page 27)
• Check if the BD disc supports BD-LIVE.
• Check the setting for “BD Internet Access”. (Page 44)
(Continued on the next page)
61
Troubleshooting
Other
Problem
Possible causes and solutions
The TV operates incorrectly.
• Some TVs with wireless remote control capability may operate incorrectly when using the remote control of this Player.
Use such TVs away from this Player.
The Player heats up during use.
• When using this Player, the console cabinet may heat up depending on the usage environment. This is not a malfunction.
POWER (ON/STANDBY) indicator will remain lit.
• When the AC cord is removed from the outlet, the POWER (ON/STANDBY) indicator will remain lit for a short period. This
is normal and is not a malfunction.
POWER
To Reset this Player
• If this Player receives strong interference from a source such as excessive static electricity, strong external noise, malfunction of power supply, or
voltage caused by lightning during use or a wrong operation is sent to the Player, errors like the Player not accepting an operation may occur.
Press and hold POWER on the Player until “
” appears on the front panel display when the Player does not operate properly even after
the power has been turned off. Then, after the POWER indicator is lit, turn on the power.
• When a reset is performed while the power is on, the Player will turn off. Turn the power on again. At this point, it may take a few moments for the system processing to finish before
the Player is ready for use. During the system processing, the BD/DVD/CD mode indicator on the front panel display of the player will blink. Once the system processing has finished,
the indicator will finish blinking and then light up normally. You can operate the Player when the BD/DVD/CD mode indicator is lit.
• Since all settings including the language setting stored in memory are also reset when a reset has been performed, they must be set again.
• When the problem persists even after performing a reset, unplug the AC cord and plug it in again. If this does not solve the problem, contact the nearest service center approved by
SHARP.
62
On-screen Error Messages
The following messages appear on the TV screen in case of an error during operation.
Error message
Possible Error
Suggested Solution
Cannot play.
• The disc cannot be played back with this Player.
• Check the disc, and load it correctly.
Incompatible disc.
• If you load a disc which cannot be played with this
Player (i.e. a scratched disc), or if you load a disc upside
down, this message will appear, and the disc tray will
automatically pop out.
• Occurs if the loaded disc cannot be played because it is • Remove the disc.
a non-standard disc or scratched, etc.
Cannot operate.
• Occurs if an operation is incorrect.
This USB memory is not formatted properly. Please format • Occurs if there is a formatting error.
the memory in USB memory management. • Occurs if the USB memory is not formatted with FAT
32/16.
• Format the USB memory again.
• Format the USB memory with your PC.
The Connected USB Memory cannot be used. It should be • Occurs if USB memory not compliant with USB 2.0 High • Connect USB 2.0 High Speed (480Mbit/s) compliant
compliant with USB 2.0 Speed (480Mbit/s) is used (i.e. USB 1.0/USB 1.1). USB memory.
63
Specifications
Specifications are subject to change without notice.
General
Power supply
AC 120 V, 60 Hz
Power consumption (Normal)
Power consumption (Standby)
Dimensions
15 W
0.3 W (When “Quick Start” is set to “No”)
Approx. 16 15 16 g 1 15 16 g 7 13
/ / /16 inch (W g H g D)
Approx. 430 mm g 58 mm g 198 mm (W g H g D)
Weight
Approx. 3.86 lbs. (1.75 kg)
Operating temperature
Storage temperature
Operating humidity
TV systems
41°F to 95°F (5°C to 35°C)
–4°F to 140°F (–20°C to 60°C)
10 % to 80 % (no condensation)
NTSC system
Playback
Playable discs/media formats
BD-ROM, BD-RE, BD-R,
DVD Video, DVD+RW/+R/-RW/-R (Video/VR/AVCHD/JPEG file/MP3 file/DivX (H.264/MKV) format),
Audio CD (CD-DA), CD-RW/R (CD-DA/JPEG file/MP3 file format)
USB memoy device (JPEG file/MP3 file/DivX (H.264/MKV) format)
Region code
A or ALL for BD, 1 or ALL for DVD
Input/Output
HDMI
HDMI 19-pin standard connector (1080p 24Hz output)
HDMI® (Deep Color, x.v.Color, Dolby TrueHD, DTS-HD Master Audio | Essential)
Digital audio optical output
USB input
Terminal: Square Optical terminal
USB1/USB2
USB 2.0 High Speed (480Mbit/s) correspondence (for Wireless LAN adapter and Local storage/Software update/JPEG,
MP3 and DivX (H.264/MKV) playback)
ETHERNET
10BASE-T/100BASE-TX
64
Specifications
Wireless LAN USB Adapter
Product name
Standard
Wireless LAN adapter (supplied)
IEEE 802.11b/g/n
Host interface
Frequency band
USB 2.0
Draft 802.11n Radio: 2.4GHz
802.11g Radio: 2.4GHz
802.11b Radio: 2.4GHz
2.400 – 2.483GHz (channel 1–11)
Modulation
Security
DBPSK @ 1 Mbps
DQPSK@ 2 Mbps
CCK@ 5.5/11 Mbps
BPSK@ 6/9 Mbps
QPSK@ 12/18 Mbps
16-QAM@ 24/36 Mbps
64-QAM@ 48/54 Mbps
AP (Infrastructure) mode supports
- Static WEP that support both 64 and 128 bit keys.
- WPA(TKIP) with PSK
Ad-hoc mode supports
- None (plaintext)
- Static WEP that supports both 64 and 128 bit keys.
Power consumption
Dimensions
TX: up to 310mA (5V)
Approx. 11
/
16
g
11
/
32 g 1 3/16 inch (W g H g D)
Approx. 17 g 8.4 g 29.8 mm (W g H g D)
Weight
Approx. 0.14 oz (3.9g)
Information on Disposal for Users (private households)
1. In the European Union
Attention: If you want to dispose of this equipment, please do not use the ordinary dust bin!
Used electrical and electronic equipment must be treated separately and in accordance with legislation that requires proper treatment, recovery and recycling of used electrical and
electronic equipment. Following the implementation by member states, private households within the EU states may return their used electrical and electronic equipment to designated
collection facilities free of charge*. In some countries* your local retailer may also take back your old product free of charge if you purchase a similar new one.
*) Please contact your local authority for further details.
The wireless LAN adapter (supplied) is
marked with this symbol. It means that
used electrical and electronic products
should not be mixed with general
household waste. There is a separate
collection system for these products.
Please contact your local authority for
the correct method of disposal of this
product and/or packaging.
If your used electrical or electronic equipment has batteries or accumulators, please dispose of these separately beforehand according to local requirements.
By disposing of this product correctly you will help ensure that the waste undergoes the necessary treatment, recovery and recycling and thus prevent potential negative effects on the
environment and human health which could otherwise arise due to inappropriate waste handling.
2. In other Countries outside the EU
If you wish to discard this product, please contact your local authorities and ask for the correct method of disposal.
65
Glossary
This Player is compatible with Deep Color. You can
enjoy this function by connecting to a Deep Color
compatible TV using an HDMI cable.
Ad-hoc mode (pages 19, 65)
BD-RE (pages 9, 25)
Ad-hoc mode is a wireless LAN communication
format. This performs direct communication
between equipment without an access point. (Ad-
hoc mode is not supported.)
A BD-RE (Blu-ray Disc Rewritable) is a recordable
and rewritable Blu-ray Disc.
Disc menu (page 26)
BD-ROM (pages 9, 25)
This lets you select things like the subtitle language
or audio format using a menu stored on the DVD
video disc.
BD-ROMs (Blu-ray Disc Read-Only Memory)
are commercially produced discs. Other than
conventional movie and video contents, these discs
have enhanced features such as interactive content,
menu operations using pop-up menus, selection of
subtitle display, and slide shows. Although a BD-
ROM may contain any form of data, most BD-ROM
discs will contain movies in High Definition format
for playback on Blu-ray Disc players.
AVCHD (page 9)
AVCHD (Advanced Video Codec High Definition)
refers to a recording format (specification) for digital
video cameras which can record to a disc such as
8 cm DVD disc and play back digital high definition
images.
Dolby Digital
A sound system developed by Dolby Laboratories
Inc. that gives movie theater ambience to audio
output when the product is connected to a Dolby
Digital processor or amplifier.
BDAV (page 9)
BDAV (Blu-ray Disc Audio/Visual, BD-AV) refers to
one of the application formats used for writable
Blu-ray discs such as BD-R, BD-RE, etc. BDAV is a
recording format equivalent to DVD-VR (VR mode) of
the DVD specifications.
Dolby Digital Plus (page 54)
Blu-ray Disc (BD) (page 9)
A sound system developed as an extension to Dolby
Digital. This audio coding technology supports 7.1
multi-channel surround sound.
A disc format developed for recording/playing high-
definition (HD) video (for HDTV, etc.), and for storing
large amounts of data. A single layer Blu-ray Disc
holds up to 25 GB, and a dual-layer Blu-ray Disc
holds up to 50 GB of data.
Dolby TrueHD (page 54)
BD-J application
Dolby TrueHD is a lossless coding technology that
supports up to 8 channels of multi-channel surround
sound for the next generation optical discs. The
reproduced sound is true to the original source bit-
for-bit.
The BD-ROM format supports Java for interactive
functions. “BD-J” offers content providers almost
unlimited functionality when creating interactive BD-
ROM titles.
Chapter number (pages 38, 39)
Sections of a movie or a music feature that are
smaller than titles. A title is composed of several
chapters. Some discs may only be comprised of a
single chapter.
BD-LIVE (page 28)
DTS
A variety of interactive content is available from BD-
LIVE compatible Blu-ray discs via the Internet.
This is a digital sound system developed by DTS,
Inc. for use in cinemas.
Control Panel (page 24)
This function allows you to operate this player using
the TV remote control by displaying the control
panel on the TV screen.
BDMV (page 9)
DTS-HD High Resolution Audio (page 54)
DTS-HD High Resolution Audio is a new technology
developed for the next generation high definition
optical disc format.
BDMV (Blu-ray Disc Movie, BD-MV) refers to one
of the application formats used for BD-ROM which
is one of the Blu-ray Disc specifications. BDMV is
a recording format equivalent to DVD-video of the
DVD specification.
Copy guard
This function prevents copying. You cannot copy
discs marked by the copyright holder with a signal
which prevents copying.
DTS-HD Master Audio (page 54)
DTS-HD Master Audio is a lossless audio
compression technology developed for the next
generation high definition optical disc format.
BD-R (pages 9, 25)
A BD-R (Blu-ray Disc Recordable) is a recordable,
write-once Blu-ray Disc. Since contents can be
recorded and cannot be overwritten, a BD-R can be
used to archive data or for storing and distributing
video material.
Deep Color
Deep Color can reproduce rich colors, increasing
the number of bits describing colors.
66
Glossary
DTS-HD Master Audio | Essential
DVD+/-RW (pages 9, 25)
Linear PCM Sound (pages 12, 42, 54)
Linear PCM is a signal recording format used for
Audio CDs and on some DVD and Blu-ray discs. The
sound on Audio CDs is recorded at 44.1 kHz with
16 bits. (Sound is recorded between 48 kHz with 16
bits and 96 kHz with 24 bits on DVD video discs and
between 48 kHz with 16 bits and 192 kHz with 24
bits on BD video discs.)
DTS-HD Master Audio | Essential is a lossless audio
compression technology developed for the next
generation high definition optical disc format.
A DVD+/-RW is a recordable and rewritable DVD.
The re-recordable feature makes editing possible.
The DVD+/-RW has two different formats: VR format
and Video format. DVDs created in Video format
have the same format as a DVD video, while discs
created in VR (Video Recording) format allow the
contents to be programed or edited.
DVD upscaling (page 25)
Upscaling (upconverting) refers to a function of
various players and devices that enlarge the image
size to fit the size of the screen of video equipments
such as a TV.
HDMI (page 16)
MP3 (pages 9–11, 32, 34)
HDMI (High-Definition Multimedia Interface) is an
interface that supports both video and audio on
a single digital connection. The HDMI connection
carries standard to high definition video signals
and multi-channel audio signals to AV components
such as HDMI equipped TVs, in digital form without
degradation.
MP3 files are audio data compressed in the
MPEG1/2 Audio layer-3 file format. “MP3 files” have
“.mp3” as extensions.
DVD video (pages 9, 25)
A disc format that contains up to eight hours of
moving pictures on a disc the same diameter as
a CD. A single-layer single sided DVD holds up to
4.7 GB; a double layer single-sided DVD, 8.5 GB; a
single layer double-sided DVD, 9.4 GB; double-layer
double-sided DVD, 17 GB. The MPEG 2 format was
adopted for efficient video data compression. It is
a variable rate technology that encodes the data to
according to the status of the video for reproducing
high-quality images. Audio information is recorded
in a multi-channel format such as Dolby Digital,
allowing for a realistic audio presence.
MPEG-2
MPEG-2 (Moving Picture Experts Group phase 2) is
one of the video data compression schemes, which
is adopted for DVD videos and digital broadcasts
worldwide. Some Blu-ray Discs also use high bitrate
MPEG-2.
Infrastructure mode (page 19)
Infrastructure mode is a wireless LAN
communication format. This performs wireless
communication through an access point.
Multi Angle (pages 37–39)
This is a feature of DVD and BD video discs. In
some discs, the same scene is shot from different
angles, and these are stored in a single disc so you
can enjoy playback from each angle. (This function
can be enjoyed if the disc is recorded with multiple
angles.)
Interlace format
Interlace format shows every other line of an image
as a single “field” and is the standard method for
displaying images on television. The even numbered
field shows the even numbered lines of an image,
and the odd numbered field shows the odd
numbered lines of an image.
DVD+/-R (pages 9, 25)
A DVD+/-R is a recordable, write-once DVD.
Since contents can be recorded and cannot be
overwritten, a DVD+/-R can be used to archive data
or for storing and distributing video material. The
DVD+/-R has two different formats: VR format and
Video format. DVDs created in Video format have
the same format as a DVD video, while discs created
in VR (Video Recording) format allow the contents to
be programed or edited.
Multi Audio (pages 37–39)
This is a feature of DVD and BD video discs. This
function makes it possible to record different audio
tracks for the same video, so you can enhance your
enjoyment by switching the audio. (You can enjoy
this function with discs recorded with multiple audio
tracks.)
JPEG (pages 9–11, 33, 34)
JPEG (Joint Photographic Experts Group) is a still
image data compression format and is used in most
of digital cameras.
Netflix (page 55)
Netflix is an online DVD and Blu-ray Disc rental
service, offering rental-by mail and streaming
instantly to Netflix unlimited members.
67
Glossary
Parental control (page 44)
Time number (pages 14, 39)
This indicates the play time which has elapsed from
the start of a disc or a title. It can be used to find a
specific scene quickly. (It may not work with some
discs.)
In some digital broadcasts and BD/DVD video discs,
a control level for disc viewing is set depending on
the age of the viewer. With this Player, you can set
the control level for viewing such broadcasts and
discs.
Title number (pages 38, 39)
Pop-up menu (page 27)
These numbers are recorded on DVD and Blu-ray
discs. When a disc contains two or more movies,
these movies are numbered as title 1, title 2, etc.
An enhanced menu operation available on BD video
discs. The pop-up menu appears when POP-UP
MENU is pressed during playback, and can be
operated while playback is in progress.
Top menu (page 26)
In a BD/DVD video, this is the menu for selecting
things like the chapter to be played back and the
subtitle language. In some DVD videos, the top
menu may be called the “Title Menu”.
Progressive format
Compared to the Interlace format that alternately
shows every other line of an image (field) to create
one frame, the Progressive format shows the entire
image at once as a single frame. This means that
while the Interlace format can show 30 frames/60
fields in one second, the Progressive format
can show 60 frames in one second. The overall
picture quality increases and still images, text, and
horizontal lines appear sharper.
Track number (pages 38, 39)
These numbers are assigned to the tracks which are
recorded on audio CDs. They enable specific tracks
to be located quickly.
VUDU (page 56)
VUDU is an on-demand video service for renting or
buying movies that can be watched instantly on TV.
Region code (page 9)
Code identifying a geographic region of
compatibility for a BD/DVD.
x.v.Color
x.v.Color reproduces a greater range of color than
before, showing almost all of the colors that the
human eye can detect. (Applicable for JPEG files
only with this system)
Resume playback (page 25)
If you stop playback while it is in progress, the
Player stores the stop position in memory, and this
function lets you playback from that point.
YouTube (page 55)
YouTube is a website where users can upload and
view video content, such as video clips and TV clips.
You can watch the content streamed on your TV.
Skip (pages 29, 30, 32, 33, 35)
This returns to the start of the chapter (or track)
being played, or skips to the next chapter (or track).
Subtitles (pages 37–39)
These are the lines of text appearing at the bottom
of the screen which translate or transcribe the
dialog. They are recorded on many DVD and BD
video discs.
68
Network Service Disclaimer
This Sharp device facilitates the access to content and services provided by third parties. The content and services accessible via this device belong to and may
be proprietary to third parties. Therefore, any use of such third party content and services must be in accordance with any authorization or terms of use provided by
such content or service provider. Sharp shall not be liable to you or any third party for your failure to abide by such authorization or terms of use. Unless otherwise
specifically authorized by the applicable content or service provider, all third party content and services provided are for personal and non-commercial use; you may
not modify, copy, distribute, transmit, display, perform, reproduce, upload, publish, license, create derivative works from, transfer or sell in any manner or medium any
content or services available via this device.
Sharp is not responsible, nor liable, for customer service-related issues related to the third party content or services. Any questions, comments or service-related
inquiries relating to the third party content or service should be made directly to the applicable content or service provider.
You may not be able to access content or services from the device for a variety of reasons which may be unrelated to the device itself, including, but not limited to,
power failure, other Internet connection, or failure to configure your device properly. Sharp, its directors, officers, employees, agents, contractors and affiliates shall
not be liable to you or any third party with respect to such failures or maintenance outages, regardless of cause or whether or not it could have been avoided.
ALL THIRD PARTY CONTENT OR SERVICES ACCESSIBLE VIA THIS DEVICE IS PROVIDED TO YOU ON AN “AS-IS” AND “AS AVAILABLE” BASIS AND SHARP AND
ITS AFFILIATES MAKE NO WARRANTY OR REPRESENTATION OF ANY KIND TO YOU, EITHER EXPRESS OR IMPLIED, INCLUDING, WITHOUT LIMITATION, ANY
WARRANTIES OF MERCHANTABILITY, NON-INFRINGEMENT, FITNESS FOR A PARTICULAR PURPOSE OR ANY WARRANTIES OF SUITABILITY, AVAILABILITY,
ACCURACY, COMPLETENESS, SECURITY, TITLE, USEFULNESS, LACK OF NEGLIGENCE OR ERROR-FREE OR UNINTERRUPTED OPERATION OR USE OF THE
CONTENT OR SERVICES PROVIDED TO YOU OR THAT THE CONTENT OR SERVICES WILL MEET YOUR REQUIREMENTS OR EXPECTATIONS.
SHARP IS NOT AN AGENT OF AND ASSUMES NO RESPONSIBILITY FOR THE ACTS OR OMISSIONS OF THIRD PARTY CONTENT OR SERVICE PROVIDERS, NOR
ANY ASPECT OF THE CONTENT OR SERVICE RELATED TO SUCH THIRD PARTY PROVIDERS.
IN NO EVENT WILL SHARP AND/OR ITS AFFILIATES BE LIABLE TO YOU OR ANY THIRD PARTY FOR ANY DIRECT, INDIRECT, SPECIAL, INCIDENTAL, PUNITIVE,
CONSEQUENTIAL OR OTHER DAMAGES, WHETHER THE THEORY OF LIABILITY IS BASED ON CONTRACT, TORT, NEGLIGENCE, BREACH OF WARRANTY,
STRICT LIABILITY OR OTHERWISE AND WHETHER OR NOT SHARP AND/OR ITS AFFILIATES HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
69
About Software License
Information on the Software License for This Product
Software composition
The software included in this product is comprised of various software components whose individual copyrights are held by SHARP or by third parties.
Software developed by SHARP and open source software
The copyrights for the software components and various relevant documents included with this product that were developed or written by SHARP are owned
by SHARP and are protected by the Copyright Act, international treaties, and other relevant laws. This product also makes use of freely distributed software and
software components whose copyrights are held by third parties. These include software components covered by a GNU General Public License (hereafter GPL), a
GNU Lesser General Public License (hereafter LGPL) or other license agreement.
Obtaining source code
Some of the open source software licensors require the distributor to provide the source code with the executable software components. GPL and LGPL include
similar requirements. For information on obtaining the source code for the open source software and for obtaining the GPL, LGPL, and other license agreement
information, visit the following website:
We are unable to answer any questions about the source code for the open source software. The source code for the software components whose copyrights are
held by SHARP is not distributed.
Acknowledgements
The following open source software components are included in this product:
• cairo • Curl • DirectFB • Droid Sans font • Droid Sans Fallback font • Expat • Fltk • FreeType • Giflib • glib • Icu • Jpeg • libcurl • libidn
• Libpng • LibPThread • Librt • libsoup • libssl and libcrypto • Libstdc++ • libxml2 • lua • lua-slncryptop • lua-xmlreader • OpenSSL
• Optional UnitTest++ Software • pango • swfdec • Webkit • zlib • linux kernel • uClibc • modutils • NanoXML • org.apache.oro.text.regex
• libsysfs • mtd/jffs2 • ncurses • Qt/Webkit • libiconv • libusb • busybox • bash • libmpeg2 • libjpeg • FontConfig
Software License Notice
Software License Notice Requirements
The software components incorporated into this product include components whose copyright holders require license notices. The license notices for these software
components are shown below.
OpenSSL License
This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit. (http://www.openssl.org)
Original SSLeay License
BSD License
This product includes software developed by the University of California, Berkeley and its contributors.
70
LIMITED WARRANTY
CONSUMER LIMITED WARRANTY
SHARP ELECTRONICS CORPORATION warrants to the first consumer purchaser that this Sharp brand product (the “Product”), when shipped in its original container, will be free
from defective workmanship and materials, and agrees that it will, at its option, either repair the defect or replace the defective Product or part thereof with a new or remanufactured
equivalent at no charge to the purchaser for parts or labor for the period(s) set forth below.
This warranty does not apply to any appearance items of the Product or if the serial number or model number affixed to the Product has been removed, defaced, changed, altered or
tampered with. This warranty does not cover installation or signal reception problems. This limited warranty will not apply if the Product has been or is being used in a commercial
setting or application; this warranty is meant solely for the non-commercial, household use of the Product by consumers in their home or residence.
In order to enforce the rights under this limited warranty, the purchaser should follow the steps set forth below and provide proof of purchase to the servicer.
To the extent permitted by applicable state law, the warranties set forth are in lieu of, and exclusive of, all other warranties, express or implied. Specifically ALL OTHER WARRANTIES
OTHER THAN THOSE SET FORTH ABOVE ARE EXCLUDED, ALL EXPRESS AND IMPLIED WARRANTIES INCLUDING THE WARRANTIES OF MERCHANTABILITY, FITNESS
FOR USE, AND FITNESS FOR A PARTICULAR PURPOSE ARE SPECIFICALLY EXCLUDED. IF, UNDER APPLICABLE STATE LAW, IMPLIED WARRANTIES MAY NOT VALIDLY BE
DISCLAIMED OR EXCLUDED, THE DURATION OF SUCH IMPLIED WARRANTIES IS LIMITED TO THE PERIOD(S) FROM THE DATE OF PURCHASE SET FORTH BELOW. THIS
WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
The warranties given herein shall be the sole and exclusive warranties granted by Sharp and shall be the sole and exclusive remedy available to the purchaser and only for the time
periods set forth herein. No other representations or promises made by anyone are permitted. Correction of defects, in the manner and for the period of time described herein, shall
constitute complete fulfillment of all liabilities and responsibilities of Sharp to the purchaser with respect to the Product, and shall constitute full satisfaction of all claims, whether
based on contract, negligence, strict liability or otherwise. Sharp does not warrant nor shall Sharp be liable, or in any way responsible, for Products which have been subject to
abuse (including, but not limited to, improper voltage), accident, misuse, negligence, lack of reasonable care, alteration, modification, tampering, improper operation or maintenance
or any damages or defects in the Product which were caused by repairs or attempted repairs performed by anyone other than a Sharp authorized servicer. Nor shall Sharp be liable
or in any way responsible for any incidental or consequential economic or property damage. Some states do not allow limits on warranties or on remedies for breach in certain
transactions; in such states, the limits herein may not apply.
THIS LIMITED WARRANTY IS VALID ONLY IN THE FIFTY (50) UNITED STATES, THE DISTRICT OF COLUMBIA AND PUERTO RICO.
Model Specific Section
Your Product Model Number & Description:
Warranty Period for this Product:
BD-HP75U BLU-RAY DISC/DVD PLAYER
(Be sure to have this information available when you need service for your Product.)
One (1) year parts and labor from the date of purchase.
Additional Item(s) Excluded from
Warranty Coverage (if any):
Non-rechargeable batteries.
Where to Obtain Service:
From a Sharp Authorized Servicer located in the United States. To find the location of the nearest Sharp Authorized Servicer,
call Sharp toll free at 1-800-BE-SHARP.
What to do to Obtain Service:
Please transport the Product in its original packaging and ensure that the Product is covered to avoid scratches and
damage. Sharp shall not be responsible for lost, stolen or misdirected mail or for damage to the product incurred during
shipping.
71
SHARP ELECTRONICS CORPORATION
Sharp Plaza, Mahwah, New Jersey 07495-1163
SHARP CORPORATION
11P02-CH-NG
|