READ THIS FIRST
Trademark Information
Microsoft® and Windows® are U.S. registered trademarks of Microsoft Corporation.
®
Pentium is a registered trademark of Intel Corporation.
Macintosh is a trademark of Apple Inc.
SD™ is a trademark.
SDHC™ is a trademark.
Other names and products may be trademarks or registered trademarks of their
respective owners.
Product Information
Product design and specifications are subject to change without notice. This
includes primary product specifications, software, software drivers, and user’s
manual. This User Manual is a general reference guide for the product.
The product and accessories that come with your camera may be different from
those described in this manual. This is due to the fact that different retailers often
specify slightly different product inclusions and accessories to suit their market
requirements, customer demographics, and geographical preferences. Products
very often vary between retailers especially with accessories such as batteries,
chargers, AC adapters, memory cards, cables, pouches, and language support.
Occasionally a retailer will specify a unique product color, appearance, and
internal memory capacity. Contact your dealer for precise product definition and
included accessories.
The illustrations in this manual are for the purpose of explanation and may differ
from the actual design of your camera.
The manufacturer assumes no liability for any errors or discrepancies in this user
manual.
EN-2
SAFETY INSTRUCTIONS
Read and understand all Warnings and Cautions before using this product.
Warnings
If foreign objects or water have entered the camera, turn the power off
and remove the battery.
Continued use might cause fire or electric shock. Consult the store of
purchase.
If the camera has fallen or its case has been damaged, turn the power off
and remove the battery.
Continued use might cause fire or electric shock. Consult the store of
purchase.
Do not disassemble, change or repair the camera.
This might cause fire or electric shock. For repair or internal inspection, ask
the store of purchase.
Do not use the camera in areas near water.
This might cause fire or electric shock. Take special care during rain, snow, on
the beach, or near the shore.
Do not place the camera on inclined or unstable surfaces.
This might cause the camera to fall or tilt over, causing damage.
Keep the battery out of the reach of children.
Swallowing the battery might cause poisoning. If the battery is accidentally
swallowed, immediately consult a physician.
Do not use the camera while you are walking, driving or riding a
motorcycle.
This might cause you to fall over or result in traffic accident.
EN-3
Cautions
Insert the battery paying careful attention to the polarity (+ or –) of the
terminals.
Inserting the battery with its polarities inverted might cause fire and injury, or
damage to the surrounding areas due to the battery rupturing or leaking.
Do not fire the flash close to anyone’s eyes.
This might cause damage to the person’s eyesight.
Do not subject the LCD monitor to impact.
This might damage the glass on the screen or cause the internal fluid to leak.
If the internal fluid enters your eyes or comes into contact with your body or
clothes, rinse with fresh water. If the internal fluid has entered your eyes,
consult a physician to receive treatment.
A camera is a precision instrument. Do not drop it, strike it or use
excessive force when handling the camera.
This might cause damage to the camera.
Do not use the camera in humid, steamy, smoky, or dusty places.
This might cause fire or electric shock.
Do not remove the battery immediately after long period of continuous
use.
The battery becomes hot during use. Touching a hot battery might cause
burns.
Do not wrap the camera or place it in cloth or blankets.
This might cause heat to build up and deform the case, resulting in fire. Use
the camera in a well-ventilated place.
Do not leave the camera in places where the temperature may rise
significantly, such as inside a car.
This might adversely affect the case or the parts inside, resulting in fire.
Before you move the camera, disconnect cords and cables.
Failure to do this might damage cords and cables, resulting in fire and electric
shock.
EN-4
Warning:
TO PREVENT THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE
FOR AMERICAN USERS
The following advisory is included in accordance with the laws of the State of
California (USA):
WARNING:
This product contains chemicals, including lead, known to the States of California to
cause cancer, birth defects or other reproductive harm. Wash hands after handling.
zꢀThis equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designated
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with instructions, may cause
harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
*
*
*
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
*
Consult the dealer or an experienced radio/TV technician for help.
zꢀChanges or modifications not expressly approved by the party responsible for
compliance could void the userís authority to operate the equipment.
EN-5
FOR CANADIAN USERS
zꢀThis Class B digital apparatus complies with Canadian ICES-003
FOR EU USERS
This symbol mark and recycling systems described below apply to
EU countries and do not apply to countries in other areas of the
world.
Your SANYO product is designed and manufactured with high
quality materials and components which can be recycled and/or
reused.
The symbol mark means that electrical and electronic equipment,
batteries and accumulators, at their end-of-life, should be disposed
of separately from your household waste.
Note:
If a chemical symbol is printed beneath the symbol mark, this
chemical symbol means that the battery or accumulator contains a
heavy metal at a certain concentration.
This will be indicated as follows: Hg: mercury, Cd: cadmium, Pb:
lead
In the European Union there are separate collection systems for
used electrical and electronic equipment, batteries and
accumulators.
Please, despose of them correctly at your local community waste
collection/recycling centre.
Please, help us to conserve the environment we live in!
Manufacturer and Address
SANYO Electric Co., Ltd.
5-5, Keihan-hondori, 2-chome,
Moriguchi City, Osaka, Japan
Authorized Representative and Address
SANYO FISHER Sales (Europe) GmbH
Stahlgruberring 4, D-81829 Munich, Germany
EN-6
Symbols used in this manual
ꢀPoints giving some extended instructions or special points to pay attention to.
You many find the answers to questions or problems concerning camera operation in
the sections “Troubleshooting”.
FCC information
Tested To Comply
With FCC Standards
FOR HOME OR OFFICE USE
Declaration of Conformity
Model number: VPC-HD100
Trade Name: SANYO
Responsible party: SANYO FISHER COMPANY
Address: 21605 Plummer Street
Chatsworth, California 91311
Telephone No.: (818) 998-7322
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
Canadian ICES-003 information
This class B digital apparatus complies with Canadian ICES-003.
EN-7
Notes on Battery Usage
When you use the battery, carefully read and strictly observe the Safety Instructions
and the notes described below:
Use only the specified battery.
Avoid extremely cold environments as low temperatures can shorten the battery
life and reduce camera performance.
When you are using a new rechargeable battery or a rechargeable battery that has
not been used for an extended period of time, it may affect the number of images
that can be captured. Therefore, to maximize its performance and lifetime, we
recommend that you fully charge the battery and discharge it for at least one
complete cycle before use.
The battery may feel warm after a long period of continuous use of the camera or
the flash. This is normal and not a malfunction.
The camera may feel warm after a long period of continuous use. This is normal
and not a malfunction.
If the battery is not to be used for a long period of time, remove it from the camera
to prevent leakage or corrosion and store it after no battery power is left. Stored for
a long time in a fully charged condition, its performance may be impaired.
Always keep the battery terminals clean.
There is a risk of explosion if the battery is replaced by an incorrect type.
Dispose of used battery according to the recycle instructions.
Charge the rechargeable!battery fully before using for the first time.
To prevent short-circuiting or fire, keep the battery away from other metal objects
when carrying or storing.
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
- SANYO Li-ion Battery, NP-61, 3.7V, 1100mAh
- BYD Li-ion Battery, NP60, 3.7V, 1050mAh
EN-8
CONTENTS
29 Slide Show Display
30 Protecting Images/Video Clips/
Audio Files
31 Deleting Images/Video Clips/
Audio Files
10 INTRODUCTION
10 Overview
10 Package Contents
12 GETTING TO KNOW YOUR
DIGITAL VIDEO CAMERA
12 Front View
12 Rear View
13 LCD Monitor Display
32 MP3 MODE
33 MENU OPTIONS
33 Video Menu
35 Capture Menu
37 Playback Menu
38 MP3 Menu
16 GETTING STARTED
16 Preparation
17 Charging the Battery
39 Setup Menu
18 Turning the Power On/Off
18 LED Indicators
19 Handling the Digital Video Camera
20 Setting the Date and Time
20 Choosing the Language
21 Formatting the Memory Card
41 INSTALLING SOFTWARE
PROGRAM
42 TRANSFERRING FILES TO
YOUR COMPUTER
42 Downloading / Deleting Your Files
via Computer
22 CAPTURE MODE
22 Recording Video Clips
22 Capturing Still Images
23 Using the Zoom Function
23 Using the Assist Light
24 Recording Shots using Face
Detection Technology
43 SPECIFICATIONS
44 APPENDIX
44 Possible Number of Shots
45 Troubleshooting
25 Setting Manual White Balance
26 AUDIO MODE
26 Recording Audio Files
26 Playing Back Audio Files
27 PLAYBACK MODE
27 Playing Back Video Clips
27 Playing Back Still Images
28 Playing Back Still Images/Video
Clips on TV
28 Connecting the Digital Video
Camera to HDTV
28 Connecting for Standard TV
29 Thumbnail Display
EN-9
INTRODUCTION
Overview
Congratulations on your purchase of the new digital video camera.
Equipped with a 5.0-megapixel sensor, this digital video camera captures still images
and video clips with high definition.
Package Contents
Carefully unpack your digital video camera and ensure that you have the following
items:
Common Product Components:
Digital video camera
Software CD-ROM
USB cable
AV cable
YPbPr (HD out) cable
Earphone
Camera strap
Camera pouch
Rechargeable lithium-ion battery
Battery charger
Quick start guide
Instruction manual
Common (Optional) Accessories:
SD/SDHC memory card
Accessories and components may vary by retailer.
EN-10
GETTING TO KNOW YOUR DIGITAL
VIDEO CAMERA
Front View
1
2
3
7
4
5
6
1. Lens
2. LED assist light
3. Speaker
4. Battery!cover
5. Strap holder
6. DC door
7. Tripod mount
EN-11
Rear View
1
2
3
4
5
6
7
8
9
10
11
12
16
13
14
15
9.
W
Zoom out (wide-angle)
button / Thumbnail button
10.W Left button
Assist light button
Power button
1. Microphone
2. Status LED
3.
4.
Play button
Up button
MODE Mode button
Right button
O Focus button
Down button
MENU Menu!button
S
11.
12.USB or AV OUT terminal
13.HDTV terminal
14.SD/SDHC memory card slot
15.Earphone jack
5.
6.
X
T
7.
OK!/!Record!/!Shutter button
16.LCD monitor
8. T
Zoom in (telephoto) button
EN-12
LCD Monitor Display
Standby Mode
Video Mode
Camera Mode
1
2
3
4
1
2
3
4
13
5
6
7
16
5
6
7
8
9
8
12 11 10 9
15
14 13 12 11 10
1. Video mode icon
1. Camera mode icon
2. Available recording time
3. Storage media
2. Available number of shots
3. Storage media
4. Battery condition
5. Focus setting
[Blank] Normal
[
q] SD/SDHC memory card
4. Battery condition
[l] Full battery power
[o] Medium battery power
[[nm]] LNoowbabtatetteryrypopwowerer
[O] Macro
[Q] Infinity
5. Focus setting
[
Blank] Normal
[Z] Face detection
6. Assist light ON
7. Scene mode
[
O] Macro
[Q] Infinity
6. Assist light ON
7. Scene mode
[Blank] Auto
8. Image stabilization icon
9. Self-timer
[ O ] Portrait
10. Capture mode icon
[ C ] Night
[
Blank] Single
[ F ] Sports
[U] AEB
[ N ] Landscape
[ K ] Sunset
[T] Continuous
11. ISO
[ X ] Beach/Snow
[ Y ] Spotlight
[ N ] User Setting
8. Self-timer
[Blank] Auto
[:] 64
[5] 100
[
e
10s] 10 sec.
[7] 200
[
e2s] 2 sec.
[9] 400
9. Exposure compensation
10. White balance
[Blank] Auto
12. Exposure compensation
13. White balance
14. Image quality
15. Image size
[%] Daylight
[#] Cloudy
[&] Fluoresc.1
[*] Fluoresc.2
[$] Tungsten
[7.7m] 3200 x 2400 (FW interpolation)
[
[
[
[
5
m
]
2560 x 1920
2048 x 1536
1280 x 960
[(] Manual WB
11. Image quality
3
1
m]
m]
[
y] Fine
VGA ] 640 x 480
[x] Standard
[w] Economy
16. Zoom status bar
12. Video size
[
[
[
] 1440 x 1080
] 1280 x 720
VGA ] 640 x 480
13. Zoom status bar
EN-13
Audio Recording Mode
(Standby)
(Recording)
1
2
3
4
1
2
7
6
5
1. Audio mode icon
1. Recording indicator
2. Status indicator (recording)
2. Available recording time
3. Storage media
4. Battery condition
5. Elapsed time
6. Recording indicator
7. Status indicator (standby)
Playback Mode
Video Mode
Camera Mode
1
2
3
4
1
2
3
8
7
5
6
4
1. Video playback mode icon
2. Elapsed time
1. Image playback mode icon
2. Storage media
3. Storage media
3. Battery condition
4. Battery condition
5. Folder and file number
6. Volume indicator
7. Video status bar
8. Playback indicator
4. Folder and file number
EN-14
MP3 Mode
Audio Playback Mode
1
2
3
4
1
2
3
4
11
10
5
8
5
6
7
9
8
7
6
1. MP3 mode icon
2. Elapsed time
3. Storage media
4. Battery condition
5. Volume indicator
6. MP3 title
1. Audio playback mode icon
2. Elapsed time
3. Storage media
4. Battery condition
5. Volume indicator
6. File name (ex. 100-0001)
7. Playback indicator
8. Audio status bar
7. MP3 list
8. MP3 menu
9. Playback indicator
10. Play mode indicator
11. MP3 status bar
EN-15
GETTING STARTED
Preparation
1. Attach the camera strap.
2. Open the battery cover.
3. Insert the supplied battery with correct orientation as
shown.
Close the battery cover and make sure it is locked
securely.
4. Insert an SD/SDHC memory card.
The digital video camera does not have built-in
memory and cannot operate without an SD/SDHC
memory card inserted. Make sure to insert an SD/
SDHC memory card before use.
Open the SD card slot cover gently.
Insert an SD/SDHC memory card (optional) to the
card slot.
Close the cover and make sure it is locked securely.
Be sure to format the SD/SDHC memory card with this video camera before its initial
usage.
To prevent valuable data from being accidentally deleted from an
SD/SDHC memory card, you can slide the write protect tab (on the
side of the SD/SDHC memory card) to “LOCK”.
To save, edit, or delete data on an SD/SDHC memory card, you
must unlock the card
/
To prevent damaging of SD/SDHC memory card, be sure to turn off
the power when inserting or removing the SD/SDHC memory card.
If inserting or removing the SD/SDHC memory card with the power
on, the digital video camera will automatically turn off.
Be careful not to drop the batteries when opening or closing the battery cover.
EN-16
Charging the Battery
Charge the battery fully with the supplied battery charger before use.
1. Insert the battery into the battery charger.
2. Connect the power cord to the charger and
insert the plug into a wall outlet.
1
The status LED on the charger lights red
when charging has started and lights
green when charging is completed. The
LED also lights green if no battery is
inserted into the charger.
2
Charging time varies according to the
ambient temperature and the status of battery.
Remove the battery after charging is completed.
The battery may feel warm after it has been charged or immediately after being used. This is
normal and not a malfunction.
When using the camera in cold areas, keep the camera and battery warm by holding them
inside your outer clothes.
EN-17
Turning the Power On/Off
Load the battery and insert an SD/SDHC memory card before starting.
Press the
button until the digital video
camera turns on.
To turn the power off, press the
button again.
The power is turned off automatically when the digital video camera has not been operated for a
defined period of time. To resume operation, turn the power on again. Refer to section in this
manual titled “Auto Off” in the setup menu for further details.
LED Indicators
Indicators
Status LED
Status LED
State
Solid green
Solid green
Description/Activity
The digital video camera is powering up.
The digital video!camera is ready to record!
images (or videos).
Status LED
Status LED
Blinking green USB communication/transfer is in progress.
Blinking green Reading/Writing files.
EN-18
Handling the Digital Video Camera
1. Open the panel by pulling it away from the digital video camera.
2. Choose the angle of the monitor that suits you best by rotating the panel.
The panel rotates up to 270°. It is useful for self-portrait.
Make sure you open the LCD panel at 90 degrees before attempting to rotate it.
Rotate the LCD panel carefully with the correct direction. Over rotation or rotating to the wrong
direction may damage the hinge that connects the LCD monitor to the digital video camera.
Avoid touching the LCD monitor when moving the LCD panel.
Cautions:
Do not hold the digital video camera by only holding the LCD panel.
Be careful not to block the lens, microphone, or LED lights with your fingers when
shooting.
Close the LCD panel when not using the digital video camera to avoid damages.
EN-19
Setting the Date and Time
The date/time needs to be set if/when:
The digital video camera is turned on for the first time.
The digital video camera is turned on after being left without battery for an
extended period of time.
1. Press the
button until the digital video
Setup
English
On
Next Menu
0
camera turns on.
Language
Beep
Format
LCD Bright.
Date/Time
2. Press the MENU button.
3. Select [Setup] with the f (O) button.
4. Select [Date/Time] with the
buttons, and press the
c
button.
(
MODE) /
d
(MENU)
Next Menu
Select the item’s field with the e (
) / f
:
:
Exit
(O) buttons and adjust the value for the
date and time with the
buttons.
OK
c
(
MODE) /
d
(MENU)
The time is displayed in 24-hour format.
After confirming all settings are correct,
Date / Time
press the
button.
2008.01.01
Y/M/D
00:00
5. To exit from the [Setup] menu, press the f (O)
button.
:
OK
Choosing the Language
Specify in which language menus and messages are to be displayed on the LCD monitor.
1. Press the MENU button.
Setup
English
On
Next Menu
0
2. Select [Setup] menu with the f (O) button.
Language
Beep
Format
LCD Bright.
Date/Time
3. Select [Language] with the
MENU buttons, and press the
4. Select the displayed language with the
MODE) / MENU buttons, and press the
c
(
MODE) /
d
(
)
button.
c
button.
(
d
(
)
Next Menu
:
:
Exit
The setting will be stored.
OK
EN-20
Formatting the Memory Card
This utility formats the SD/SDHC memory card and deletes all stored images, video
clips, and data.
1. Press the MENU button.
Setup
English
On
Next Menu
0
2. Select [Setup] menu with the f (O) button.
Language
Beep
Format
LCD Bright.
Date/Time
3. Select [Format] with the
c
(
MODE) /
button.
MODE) /
button.
To cancel formatting, select [No] and press
the button.
d
(MENU)
buttons, and press the
4. Select [Yes] with the
c
(
d
(MENU)
buttons, and press the
Next Menu
:
:
Exit
OK
5. To exit from the [Setup] menu, press the f (O)
button.
Format
Format Card?
No
Yes
:
:
OK
Exit
EN-21
CAPTURE MODE
Your digital video camera is equipped with a 2.5" full color LTPS LCD monitor to help
you capture/playback images and video clips or adjust menu settings.
Recording Video Clips
1. Press the
button until the digital video
camera turns on.
The default mode is Video Mode.
2. Compose the image on the LCD monitor.
3. Press the
4. To stop recording, press the
The recording time depends on the
button to start recording.
button.
storage media size and the subject to be
recorded.
If the acess speed of your SD/SDHC memory card is not fast enough for recording video clips in
the currently selected size, the recording will stop. In this case, select a video quality lower than
the current one.
When using SDHC memory card to record high resolution video clips, higher than Class 4 is
recommended to prevent recording from discontinuing.
Capturing Still Images
1. Press the
button until the digital video
camera turns on.
2. Press the MODE button to switch to capture
mode.
3. Compose the image on the LCD monitor.
4. Press the
button to capture the image.
EN-22
Using the Zoom Function
Using a combination of 5x optical zoom and 4x digital zoom permits zoom photogra-
phy at up to 20x magnification. While the digital zoom can be a useful feature, the
more an image is enlarged (zoomed), the more pixelated (grainier) the image will
appear.
To capture a zoomed image/video clip, perform the following steps:
1. Compose the image on the LCD monitor.
Press the T
button to zoom in on the
subject, and enlarge the subject on the LCD
monitor.
Press the
the image.
W button to view a wider angle of
The status of digital magnification is displayed
on the zoom status bar.
At 1440 x 1080 (video mode): the preview can
reach digital zoom to 2x. At 1280 x 720 and 640 x 480 (video mode): the
preview can reach digital zoom to 4x.
2. Press the
button to capture/record the image/video clip.
To activate digital zoom function, set [Digi. Zoom] to [On] in the capture or video menu.
Using the Assist Light
When capturing still images/video clips in dark places, you can turn on the LED assist
light in front of the digital video camera to help brightening and focusing on the sub-
ject.
1. In video/capture mode, press the
turn the LED assist light on or off.
button to
The assist light can only be activated in capture or video mode. When the digital video camera
is switched to playback, audio or MP3 mode, the assist light will turn off automatically.
EN-23
Recording Shots using Face Detection Technology
Face Detection Technology can identify and focus on the human faces in the image.
This advanced function simultaneously detects up to 9 human faces regardless of
their position in the scene.
White frame
Green frame
Face detection function is on
Focus lock
Out of focus
1. In capture mode, toggle
O
button until [Z] icon appears on the LCD monitor.
The white frame is identified as the “top priority” face (main focus frame), and
gray ones around the other faces.
2. Press the
button halfway down to lock the focus.
The main focus frame simultaneously turns green.
If the “top priority” face is out of focus, all frames will be disappeared from the
screen.
3. Press the
button down fully to capture your image.
Subjects that are not suitable with this function:
a. A person is wearing glasses, sunglasses, or face is covered with hat or hair.
b. A person turns sideways.
EN-24
Setting Manual White Balance
You can manually set and store the white balance when the menu options do not offer
a good match.
1. In video/capture mode, press the MENU
Manual WB
Use Data
New WB
button.
2. Select [W.Balance] with the
c
(
MODE) /
button.
MODE) /
d
(
MENU) buttons, and press the
3. Select [Manual WB] with the
MENU buttons, and press the
4. Select [New WB], and press the
c
(
d
(
)
button.
button.
:
:
OK
Exit
To use the previously set white balance
data, select [Use Data], and press the
button.
New WB
5. Point the video camera at a white paper or
white slate, and press the button.
When the manual white balance is stored,
[COMPLETE] will be displayed and the
video camera returns to recording mode.
:
:
OK
Exit
EN-25
AUDIO MODE
Recording Audio Files
The digital video camera enables you to record and playback audio files anytime and
anywhere.
1. Press the MODE button to switch to audio mode.
2. Press the
button to start audio recording.
To stop recording, press the button.
Playing Back Audio Files
1. Press the
button.
2. Select the desired audio clip with the e (
) / f
(O) buttons.
3. Press the
button to begin playback.
To pause, press the button again.
To stop playback, press the
d
(
MENU
)
button.
To adjust the volume, use the
buttons.
W / T
EN-26
PLAYBACK MODE
You can play back all the recorded files on the LCD monitor.
Playing Back Video Clips
1. Press the
button.
The last recorded file appears on the LCD
monitor.
2. Select the desired video clip with the e (
) /
f (O) buttons.
3. Press the
button to start video playback.
To pause video playback, press the
button.
To cancel pause, press the
To adjust the volume, use the
button again.
W / T
buttons.
4. To stop video playback, press the
video clip.
d
(MENU) button and return to the start of the
Video clips cannot be displayed rotated or enlarged.
To play the video clip back on your computer, you may use Windows Media Player 9 above
version. Windows Vista user may use Windows Movie Maker.
Playing Back Still Images
1. Press the
button.
The last recorded file appears on the LCD
monitor.
2. Select the desired image with the e (
) / f
(O) buttons.
3. Press the T
button to adjust the zoom ratio.
The magnification factor is displayed on the
LCD monitor.
4. To view different portion of the images, press
the MODE) / MENU / e ( ) / f (O)
buttons to adjust the display area.
c
(
d
(
)
The magnification factors range from 1.5x to 8.0x.
EN-27
Playing Back Still Images/Video Clips on TV
You can also playback your images on a TV screen. Before connecting to any devices,
make sure to select NTSC / PAL system to match the video input system of the TV/video
equipment you are going to connect to the digital video camera, then turn all connected
devices off.
1. Connect one end of the AV cable to the AV OUT terminal of the digital video camera.
2. Connect the other end to the AV input socket of the TV set.
3. Turn the TV and digital video camera on.
4. Playback the still images/video clips.
5. The method of operation is the same as playing back still images and video clips!on the
digital video camera.
Connecting the Digital Video Camera to HDTV
HD TV (High Definition Television) is a digital television broadcasting system with!better res-
olution than traditional television systems. It can perform HD (720P) high!resolution quality.
HD TV
(green)
(green)
(blue)
(red)
Video IN
(blue)
(red)
(red)
(white)
(yellow)(no connection)
Audio IN
A/V OUT
(white)
<AV cable>
COMPONENT (HD OUT)
<YPbPr(HD out) cable>
1. Connect one end of the YPbPr (HD out) cable into the (Video IN) port on the HDTV!and
the other end into the HDTV terminal of the digital video camera.
2. Connect one end of the AV cable into the (Audio IN) socket of the HDTV and the other
end into the AV OUT terminal of the digital video camera. (Do not connect the yellow
connector to HDTV’s AV-IN.)
3. Turn the TV and digital video camera on.
The video camera will auto detect and set the settings when the cables are
connected.
Connecting for Standard TV
(red)
(white)
Audio - IN
(white)
(yellow) Video - IN
(yellow)
EN-28
Thumbnail Display
This function allows you to view thumbnail images on the LCD monitor so you may
search for a particular image/video clip/audio file.
1. In playback mode, press the
3 thumbnail images are displayed
simultaneously.
2. Use the MODE) /
select the file to be displayed.
Use the e ( ) / f (O) buttons to go to
previous or next page.
3. Press the button to display the selected
image on full screen.
W button.
c
(
d
(MENU) buttons to
Slide Show Display
The slideshow function enables you to play back your still images automatically in
sequential order as a slideshow. This is a very useful and entertaining feature for
reviewing captured images and for presentations.
1. In the playback mode, press the MENU button.
Play
2. Select [Slide Show] with the
c
(
MODE) /
button.
3. Select the desired interval time with the
MODE) / MENU buttons, and press the
button.
d
Delete File
Delete All
Slide Show
Protect
No
5 Sec.
7 Sec.
9 Sec.
(
MENU) buttons and press the
c
(
d
(
)
The slide show starts.
To stop the slideshow during playback,
press the button.
:
:
OK
Exit
Video clips are displayed as images and will not be played back.
Audio files are not displayed in slide show.
EN-29
Protecting Images/Video Clips/Audio Files
Set the data to read-only to prevent files from being deleted by mistake.
Protecting One File
1. Press the
2. Select the file you wish to protect with the
e ( ) / f (O) buttons.
button.
Play
Delete File
Delete All
Slide Show
Protect
No
Next Menu
Single
All
3. Press the MENU button.
4. Select [Protect] with the
buttons and press the
5. Select [Single] with the
buttons, and press the
c
(
MODE) /
d
(
MENU
)
button.
MODE) /
button.
c
(
d
(
MENU
)
:
:
Exit
OK
The selected file is protected.
To cancel protection, perform step 1 to 5 again.
Protecting All Files
1. Select [All] from the Protect menu and press the
button.
2. Select [Lock] with the
c
(
MODE) /
d
(
MENU
)
buttons, and press the
button.
All stored files are protected.
To cancel all protection, perform the above steps and select [Unlock] in step 2.
To cancel protection for one specific file, perform above step 1 to 5 of
"Protecting One File".
The protect icon A is displayed with protected files.
Formatting an SD/SDHC memory card overrides protection, and deletes all files regardless of
their protected status.
EN-30
Deleting Images/Video Clips/Audio Files
1. Press the
2. Select the file you wish to delete with the
e ( ) / f (O) buttons.
3. Press the MENU button.
4. Select [Delete File] or [Delete All] with the
button.
Play
Delete File
Delete All
Slide Show
Protect
No
Yes
5 Sec.
Single
c
button.
(
MODE) /
d
(MENU) buttons and press the
:
:
OK
Exit
[Delete File]: Deletes the current file.
[Delete All]: Deletes all files.
5. Select [Yes] to delete. Select [No] to cancel.
6. Press the button to confirm.
EN-31
MP3 MODE
The digital video camera enables you to playback MP3 files. You may download MP3
files to your computer and then copy them into an SD/SDHC memory card (into an
"MP3" folder). Insert an SD/SDHC memory card with MP3 files recorded into the
digital video camera.
1. Press the MODE button to switch to MP3
mode.
2. Press the
W button to enter the MP3 List
and select the MP3 file you wish to playback.
Press the
button to confirm.
button to begin playback.
To pause, press the button again.
3. Press the
To adjust the volume, use the
buttons.
4. To stop playback, press the
W / T
d
(MENU
)
button.
To delete MP3 files, connect the digital video camera to your computer. Select and delete the
files via the computer. For further information, please refer to the section in this manual titled
“Downloading / Deleting Your Files via Computer” (page 42).
EN-32
MENU OPTIONS
Video Menu
This menu is for the basic settings to be used when shooting video clips.
Video
Scene
Self-timer
Size
Quality
EV
Video
Video
Sharpness
Auto
Off
1280 x 720
Standard
Auto
Off
Center
Standard
Standard
:
Standard
W.Balance
Digi. Zoom
Metering
Color
Contrast
0
:
:
:
:
:
OK
Exit
Exit
Exit
OK
OK
1. The default mode is Video Mode.
2. Press the MENU button.
3. Select the desired option item with the
button to enter its respective menu.
c
(
MODE) /
MODE) /
) button.
d
(
MENU
)
buttons, and press the
4. Select the desired setting with the
button.
c
(
d
(
MENU buttons, and press the
)
5. To exit from the menu, press the e (
Scene
Select from 9 different scene modes in accordance with the shooting conditions.
* [Blank] Auto
* [ O ] Portrait
* [ C ] Night
* [ F ] Sports
* [ N ] Landscape
* [ K ] Sunset
* [ X ] Beach/Snow
* [ Y ] Spotlight
* [ N ] User Setting
Self-timer
This activates the self-timer and sets the delay time.
* [Blank] Off
* [e
2s] 2 Sec.
* [e10s] 10 Sec.
Size
This sets the size of the video clips that will be captured.
* [
* [
] 1440 x 1080
] 1280 x 720
* [VGA] 640 x 480
Quality
This sets the quality (compression) at which the video clips is captured.
* [y] Fine
* [x] Standard
* [w] Economy
EN-33
EV
Your digital video camera adjusts the exposure of each shot automatically. However, if
the subject is very dark, or very bright, you may override the digital video camera's
automatic exposure determination to make the subject brighter or darker. This is
called EV compensation. The EV compensation can be adjusted from -1.8EV to
+1.8EV.
W.Balance
This sets the white balance for a variety of lighting conditions and permits images to
be captured that approach the conditions that are seen by the human eye.
* [Blank] Auto
* [%] Daylight
* [#] Cloudy
* [&] Fluoresc.1
* [*] Fluoresc.2
* [$] Tungsten
* [(] Manual WB
Digi. Zoom
This sets whether or not to use digital zoom at the time of photography.
* On / Off
Metering
This sets the metering method for calculating the exposure.
* Center: Averages the light metered from the entire frame, but gives greater weight to
the subject matter in the center.
* Spot: A very small portion of the center of the screen is measured, and the exposure
is calculated.
Color
This sets the color of the video clips that will be captured.
* Standard / Vivid / B&W / Sepia
Contrast
This sets the degree of difference between light and dark in video clips that will be
captured.
* Standard / Hard / Soft
Sharpness
This sets the sharpness of the video clips that will be captured.
* Standard / Hard / Soft
EN-34
Capture Menu
This menu is for the basic settings to be used when capturing still images.
Capture
Scene
Self-timer
Size
Quality
EV
Capture
Capture
Metering
Color
Contrast
Sharpness
Center
Auto
Off
5M
Standard
0
W.Balance
Digi. Zoom
ISO
Capture Md.
Image Stab.
Auto
Off
Auto
Single
Off
Standard
Standard
Standard
:
:
:
:
:
:
Exit
Exit
Exit
OK
OK
OK
1. Press the MODE button to switch to capture mode.
2. Press the MENU button.
3. Select the desired option item with the
c
(
MODE) /
d
(
MENU
)
buttons, and press
the
button to enter its respective menu.
4. Select the desired setting with the
button.
5. To exit from the menu, press the e (
c
(
MODE) /
d
(MENU) buttons, and press the
) button.
Scene
Refer to the section in this manual titled “Scene” in Video Menu (page 33) for further details.
Self-timer
Refer to the section in this manual titled “Self-timer” in Video Menu (page 33) for
further details.
Size
This sets the size of the images that will be captured.
* [7.7m] 3200 x 2400 (FW interpolation)
* [5m] 2560 x 1920
* [3m] 2048 x 1536
* [1m] 1280 x 960
* [VGA] 640 x 480
Quality
Refer to the section in this manual titled “Quality” in Video Menu (page 33) for further details.
EV
Refer to the section in this manual titled “EV” in Video Menu (page 34) for further details.
W.Balance
Refer to the section in this manual titled “W.Balance” in Video Menu (page 34) for fur-
ther details.
EN-35
Digi. Zoom
Refer to the section in this manual titled “Digi. Zoom” in Video Menu (page 34) for fur-
ther details.
ISO
This sets the sensitivity for capturing images. When the sensitivity is raised (and the
ISO figure is increased), photography will become possible even in dark locations, but
the more pixelated (grainier) the image will appear.
* [Blank] Auto
* [:] 64
* [5] 100
* [7] 200
* [9] 400
Capture Md.
This sets the shooting mode for capturing still images.
* [Blank] Single: Captures a single image.
* [U] AEB: Auto exposure bracketing capture mode.
* [T] Continuous: Captures 3 images continuously.
Image Stab.
This sets whether or not to use image stabilization at the time of photography. This
function minimizes the influences of hand shaking when you want to capture an
image.
* Off / On
Metering
Refer to the section in this manual titled “Metering” in Video Menu (page 34) for further
details.
Color
Refer to the section in this manual titled “Color” in Video Menu (page 34) for further
details.
Contrast
Refer to the section in this manual titled “Contrast” in Video Menu (page 34) for further
details.
Sharpness
Refer to the section in this manual titled “Sharpness” in Video Menu (page 34) for fur-
ther details.
EN-36
Playback Menu
In this menu, choose which settings are to be used for still image/video clip playback.
Play
Delete File
Delete All
Slide Show
Protect
No
Next Menu
5 Sec.
Single
:
:
Exit
OK
1. Press the
button.
2. Press the MENU button.
3. Select the desired option item with the
c
(
MODE) /
d
(
MENU
)
buttons, and press
the
button to enter its respective menu.
4. Select the desired setting with the
button.
5. To exit from the menu, press the e (
c
(MODE) /
d
(MENU) buttons, and press the
) button.
Delete File
Refer to section in this manual titled “Deleting Images/Video Clips/Audio Files” (page 31) for
further details.
Delete All
Refer to section in this manual titled “Deleting Images/Video Clips/Audio Files” (page 31) for
further details.
Slide Show
Refer to section in this manual titled “Slideshow Display” (page 29) for further details.
Protect
Refer to section in this manual titled “Protecting Images/Video Clips/Audio Files”
(page 30) for further details.
EN-37
MP3 Menu
This menu is for the basic settings to be used when playing back MP3 files.
MP3
Single
Off
Play Mode
Repeat
:
:
Exit
OK
1. Press the MODE button to switch to MP3 mode.
2. Press the MENU button.
3. Select the desired option item with the
c
(
MODE) /
d
(
MENU
)
buttons, and press
the
button to enter its respective menu.
4. Select the desired setting with the
button.
5. To exit from the menu, press the e (
c
(
MODE) /
d
(MENU) buttons, and press the
) button.
Play Mode
Set the playback mode of the MP3 files.
* [Single]: Play a single MP3 file.
* [All]: Play all MP3 files.
Repeat
Set the repeat mode of the MP3 files.
* [Off]: Play the listed files only once.
* [On]: Play the listed MP3 files repeatedly.
EN-38
Setup Menu
This menu sets your digital video camera’s operating environment.
Setup
English
On
Next Menu
0
Setup
1 Min.
NTSC
50 Hz
No
Next Menu
Language
Beep
Format
LCD Bright.
Date/Time
Auto Off
Video Out
Light Freq.
Sys. Reset
Version
Next Menu
:
:
:
:
Exit
Exit
OK
OK
1. Press the MENU button.
2. Select the [Setup] menu with the f (O) button.
3. Select the desired option item with the MODE) /
the button to enter its respective menu.
c
(
d
(
MENU
)
buttons, and press
4. Select the desired setting with the
button.
c
(
MODE) /
d
(MENU) buttons, and press the
5. To exit from the menu, press the f (O) button.
Language
Refer to section in this manual titled “Choosing the Language” (page 20) for further details.
Beep
This sets whether or not to mute the digital video camera sound each time you press
the digital video camera's buttons.
* On / Off
Format
Refer to section in this manual titled “Formatting the Memory Card” (page 21) for further
details.
LCD Bright.
This sets the brightness of the LCD monitor screen.
* The adjustment range is from -5 to +5.
Date/Time
Refer to section in this manual titled “Setting the Date and Time” (page 20) for further
details.
Auto Off
If no operation is performed for a specific period of time, the power to the digital video
camera is automatically turned off. This feature is useful to reduce battery usage.
* Off / 1 Min. / 3 Min. / 5 Min. / 10 Min.
EN-39
Video Out
Set TV/video compatibility with the equipment you are going to connect to the digital
video camera.
* NTSC / PAL
Light Freq.
The function allows to change the light frequency of environment to 60 Hz or 50 Hz.
* 50 Hz / 60 Hz
Sys. Reset
Return all basic settings to the digital video camera's default settings.
* No / Yes
Version
This display the firmware version of the digital video camera.
EN-40
INSTALLING SOFTWARE PROGRAM
1. Please make sure you have Windows Media Player 9 or QuickTime 7.0 installed
onto your computer first.
2. Please install the decoder program (available in the CD).
H.264 files may be played back with Windows Media Player 9. (Decoder is
designed for H.264 decode)
MP4/H.264 playback system requirements:
At least 512MB of RAM
64MB or higher video card
Windows 2000 Service Pack 4 or XP or Vista 32 or Vista 64
DirectX 9.0b or higher
Audio format 48KHz HE-AAC or AAC
Resolution
fps
CPU requirements
640!x!480
1280!x!720
1440!x!1080
30 fps
30 fps
30 fps
2.4 GHz Intel Pentium 4 or higher
3.2 GHz Intel Pentium D(dual-core) or higher
Core 2 Duo 2.0 & 128MB independent memory for
image display
EN-41
TRANSFERRING FILES TO YOUR
COMPUTER
System Requirement
Windows
Macintosh
Pentium III 800 MHz or equivalent
PowerPC G3/G4/G5
Windows 2000/XP/Vista
256MB RAM (512MB recommended)
150MB available hard disk space
CD-ROM drive
OS 9.0 or later
256MB RAM (512MB recommended)
128MB hard disk space
CD-ROM drive
Available USB port
Available USB port
Downloading / Deleting Your Files via Computer
1. Press the
button until the digital video camera turns on.
2. Connect one end of the USB cable (supplied) to
the USB terminal of the digital video camera.
3. Connect the other end of the USB cable to an
available USB port on your computer.
4. From the Windows desktop, double click on “My
Computer”.
5. Look for a new “removable disk” icon.
This “removable disk” is actually the memory
(or memory card) in your video camera.
Typically, the video camera will be assigned drive letter “E” or higher.
6. Double click on the removable disk and locate the DCIM, MP3 and AUDIO folders.
7. Double click on the respective folder to open it to find more folders.
Your recorded images, video clips, audio files will be inside these folders.
8. Copy and paste or drag and drop files to a folder on your computer.
Copy MP3 files from your computer into the MP3 folder of your SD/SDHC
memory card.
9. To delete files, simply select the unwanted files and delete.
Mac users: Double-click the “untitled” or “unlabeled” disk drive icon on your desktop.
iPhoto may automatically launch.
Notes on Image Printing
After transferring data to a computer, it stores and displays the digital images that
have been saved in the SD/SDHC memory card from the digital video camera and
enables those images to be printed on a variety of digital printers.
EN-42
SPECIFICATIONS
Item
Description
Image sensor
Effective pixels
Image resolution
1/2.5” CMOS sensor
5.0 megapixels
<Still image>
7.7M: 3200 x 2400 (FW interpolation),
5M: 2560 x 1920, 3M: 2048 x 1536,
1M: 1280 x 960, VGA: 640 x 480
<Video clip>
1440 x 1080 (30 fps), 1280 x 720 (30 fps), 640 x 480 (30 fps)
Recording media Supports SD/SDHC memory card (up to 8GB) (optional)
File format
Lens
Image format: JPEG; Video format: H.264; Audio format: AAC
Aperture: F3.3 ~ F3.7
Focal Length: 6.4 ~ 32 mm
Focus range
Macro
Wide: 10cm ~ infinity
Tele: 1m ~ infinity
Standard
Wide: 50cm ~ infinity
Tele: 1m ~ infinity
Shutter speed
LCD monitor
Self-timer
1 ~ 1/4000 sec.
2.5” full color LTPS LCD (153K pixels)
10 sec delay, 2 sec delay
Exposure
-1.8EV~ +1.8EV (in 0.3EV increments)
compensation
White balance
Auto, Daylight, Cloudy, Fluoresc.1, Fluoresc.2, Tungsten,
Manual WB
ISO
Auto, 64, 100, 200, 400 (Standard Output Sensitivity)
* Sensitivity is measured in compliance with the ISO Standard
(ISO 12232:2006)
Interface
Power
USB terminal, AV/OUT terminal, HDTV terminal, earphone jack
Rechargeable Lithium-ion battery (3.7V)
Dimensions
Weight
Approx. 87.4 x 114.6 x 40.5 mm (without protruding parts)
Approx. 164g (without battery and memory card)
* Design and specifications are subject to change without notice.
EN-43
APPENDIX
Possible Number of Shots
The table shows the approximate shots/recording time that you can capture/record at
each setting based on the capacity of the SD/SDHC memory card.
Possible recording time / sec (video clip)
SD/SDHC memory card capacity
Size
Quality
4GB
SDHC
8GB
SDHC
128MB
256MB
512MB
1GB
2GB
y
x
w
y
x
w
y
x
w
Fine
00:01:57 00:04:04 00:08:17 00:16:46 00:33:12 01:05:46 02:11:38
Standard
!Economy
Fine
00:09:28
00:11:01
00:37:52
01:15:00 02:30:06
00:02:14 00:04:39
00:02:37 00:05:26
00:19:08
00:22:17
1440 x 1080
1280 x 720
00:44:04 01:27:14
00:44:04 01:27:14
00:52:40 01:44:15
01:05:26 02:09:29
02:54:34
02:54:34
03:28:37
00:02:37 00:05:26 00:11:01 00:22:17
00:03:09 00:06:30 00:13:11 00:26:38
00:03:57 00:08:06 00:16:24 00:33:06
00:05:14 00:10:44 00:21:40 00:43:42
00:06:15 00:12:47 00:25:48 00:52:01
Standard
!Economy
Fine
04:19:04
01:26:21
01:42:44
02:50:50 05:41:47
03:23:15 06:46:37
VGA
640 x 480
Standard
!Economy
00:07:43 00:15:47 00:31:51 01:04:12 02:06:50 04:10:56 08:22:02
Possible number of shots (still image)
SD/SDHC memory card capacity
Size
Quality
4GB
8GB
SDHC
128MB
256MB
512MB
1GB
2GB
SDHC
y
Fine
32
42
53
46
61
67
89
111
95
138
184
229
195
259
323
291
388
483
599
797
991
1625
2162
2693
278
369
460
391
519
545
725
903
767
1091 2194
1450 2917
1805 3632
1532 3081
7.7m
x Standard
w
3200 x 2400
(FW interpolation)
!Economy
y
Fine
5
m
x Standard
w
126
157
142
189
236
294
391
486
797
1061
1322
1019 2036 4094
1269 2535 5098
1141
2560 x 1920
!Economy
Fine
76
647
y
69
582
2279 4583
3
m
x Standard
w
92
774
1517 3030 6092
1880 3774 7588
2340 4670 9387
2048 x 1536
!Economy
Fine
115
144
191
238
390
520
648
965
y
1195
1588
1976
3239
4309
1
m
x Standard
w
3110
6207 12477
1280 x 960
!Economy
3869 7722 15523
6341 12654 25437
8436 16836 33844
y
Fine
VGA
640 x 480
x Standard
!Economy
w
5370 10512 20978 42169
EN-44
Troubleshooting
Refer to the symptoms and solutions listed below before sending the digital video
camera for repairs. If the problem persists, contact your local reseller or service
center.
Solutions / Corrective
Actions
Symptom
Cause
The power does not The battery is not inserted.
Insert the battery correctly.
Recharge the battery.
come on.
The battery is exhausted.
The battery or
Long period of continuous use
video camera feels of the video camera.
warm.
Even if press the
The SD/SDHC memory card Insert a new SD/SDHC memory
shutter button, the does not have any free
card, or delete unwanted files.
digital video does
not shoot.
capacity.
The video camera is not in
shooting mode.
Set the video camera to shoot-
ing mode.
The SD/SDHC memory card Remove the write-protection.
is write-protected.
The video camera
cannot focus.
The lens is dirty.
Wipe clean with a soft, dry cloth
or lens paper.
The distance to the subject is
Place your subject within the
smaller than the effective range. effective focus range.
Files cannot be
deleted.
The file is protected.
The SD/SDHC memory card Remove the write-protection.
is write-protected.
Cancel protection.
Cannot download
images.
The free space on the hard
Check whether the hard disk has
disk in your computer may be a space for running Windows,
insufficient.
and if the drive for loading image
files has a capacity at least that
of the memory card inserted in
the video camera.
EN-45
|