INSTRUCTION MANUAL
Digital Movie Camera
VPC-CA8EX
VPC-CA8GX
Important note
This manual explains how to safely operate the VPC-CA8EX and VPC-
CA8GX.
Any information regarding only one of these products will be labeled as such.
Please read these instructions carefully before using the camera.
Make sure to read and understand the separate booklet “SAFETY MANUAL”.
Keep this manual in a safe place for later reference.
FOR CANADIAN USERS
i This Class B digital apparatus complies with Canadian ICES-003.
FOR EU USERS
Note:
iThis symbol mark and recycle system apply only to EU
countries and do not apply to countries in other areas of
the world.
Your SANYO product is designed and manufactured with
high quality materials and components which can be
recycled and reused.
This symbol means that electrical and electronic
equipment, at their end-of-life, should be disposed of
separately from your household waste.
Please dispose of this equipment at your local community
waste collection/recycling centre.
In the European Union there are separate collection
systems for used electrical and electronic products.
Please help us to conserve the environment we live in!
SANYO FISHER Sales (Europe) GmbH
Stahlgruberring 4, D-81829 München, Germany
SANYO Electric Co., Ltd.
1-1, Sanyo-cho, Daito City, Osaka 574-8534, Japan
FOR RUSSIAN USERS
This product certified by official certification company
which is authorized by Russian Federation.
English
ii
Symbols used in this manual
HINT
Points giving some extended instructions or special points to pay
attention to.
CAUTION Points that require special attention.
(page xx) Refer to the page indicated for detailed information.
You may find the answers to questions or problems concerning camera
operation in the sections “COMMONLY ASKED QUESTIONS” (page 165)
and “TROUBLESHOOTING” (page 172).
iii English
SHOOT, PLAY BACK AND SAVE
Install the battery pack and card
1
Insert the battery pack.
Battery pack slot
1 Press the latch
Lever
1 Push
2 Open
Bottom side
2 Insert
2
Insert the SD Memory Card.
h An SD Memory Card is not included with your camera. Please
purchase a commercially sold card.
h In this manual, the SD Memory Card is referred to as the “card”.
Card slot
1 Open
2 Insert
English iv
SHOOT, PLAY BACK AND SAVE
Before capturing those important shots, be sure to first take a
test shot to confirm that your camera is set up and ready to go
i Sanyo declines any claim for compensation for recorded contents etc. in
case of photographing or recording failure due to a chance camera or card
flaw.
Shooting
kVideo clip recording
[
] button
ON/OFF button
Monitor unit
1
Open the monitor unit, and
press the ON/OFF button
for at least 1 second.
h The camera turns on.
h
If the screen to set the date
and time appears, press
the MENU button 2 times
to cancel it.
For how to set the date
and time, see page 32.
2
Press the [
h Recording begins.
] button.
h To stop recording, press
the [
] button again.
kStill image
photography
[
] button
1
Open the monitor unit, and
press the ON/OFF button
for at least 1 second.
668
01:17:32
h The camera turns on.
2
Press the [
h A still image is captured.
] button.
v
English
Playback
kVideo clip playback
1
Press the REC/PLAY button.
h The display switches to the
Playback Screen.
SET button
REC/PLAY button
h Press the [G] or [H] button
to display the video clip you
wish to play back.
h Video clips are indicated by
a video clip pattern along
the left and right sides of the
screen.
2
Press the SET button.
h Playback of the selected
video clip begins.
Arrow buttons
kStill image playback
1
Press the REC/PLAY button.
h The display switches to the
Playback Screen.
SAVE
h To view other images, press
the [G] or [H] button.
<To return to the Shooting
Screen>
h Press the REC/PLAY
button.
PLAY
Video clip pattern
<Example: After recording
a video clip>
When you are finished using the camera...
Press the ON/OFF button for at least 1 second to turn the camera off.
English vi
SHOOT, PLAY BACK AND SAVE
Burn your recorded video clips onto a DVD
(Windows XP)
Introduced here is the procedure to use the supplied DVD-ROM (Xacti
Software DVD) to burn movies captured with your camera to a DVD,
creating your original DVD.
Install the application programs
Install the following program from the Xacti Software DVD to your computer:
Adobe Premiere Elements 4.0 (in this manual, referred to as Premiere
Elements) for creating DVDs.
1
2
Set the supplied DVD-ROM (Xacti Software DVD) in your computer’s
DVD drive.
h The installation window opens.
Click on the application program you wish to install.
Install Premiere Elements.
h After clicking on an application program, follow the instructions shown
on the monitor to install the program.
h When installing Premiere Elements, input the serial number found on
the DVD-ROM envelope. It looks similar to the following:
SERIAL NUMBER: XXXX-XXXX-XXXX-XXXX-XXXX-XXXX
(
input this number)
↑
h When the installation is complete, the product registration window will
appear, but click on the Exit button to close the window.
vii English
3
In the installation window, click on [Finish].
h The installation window closes.
h Remove the DVD-ROM from your computer’s DVD drive.
<About the Kodak online service>
h When the installation window closes, a dialog box to connect to the
website introducing Kodak’s online service appears. Check the [No
thanks !] option button, and then click on the [OK] button.
Copy data from your camera to the computer
Connect your camera to a computer, and copy the desired data to the
computer.
1
2
Turn on the computer, and use the supplied dedicated USB interface
cable to connect your camera to the computer.
h Connect the cable between the camera’s USB/AV terminal and the
computer’s USB connector.
Turn on the camera (page 30).
h The USB Connection Screen appears on the camera’s monitor.
SET button
Supplied dedicated
USB interface cable
USB CONNECTION
To USB connector
on the computer
COMPUTER
To USB/AV terminal
on the camera
PRINTER
CANCEL
CANCEL
OK
English viii
SHOOT, PLAY BACK AND SAVE
3
Select “COMPUTER”, and press the SET button.
h The screen to select the computer
USB CONNECTION
connection mode appears.
CARD READER
MTP
SCREEN CAPTURE
PC CAMERA
CANCEL
OK
4
5
Select “CARD READER”, and press the SET button.
Copy data from your camera to a computer.
ix English
Burn video clips onto a DVD
CAUTION
Before writing data to a DVD
i Please note that in the case of a large amount of data it can take a long
time to burn it to DVD.
1
2
Insert a blank DVD in your computer’s DVD drive.
Double-click on your desktop’s Premiere Elements icon to run the
Premiere Elements program.
h The Premiere Elements welcome screen appears.
[New Project] icon
English
x
SHOOT, PLAY BACK AND SAVE
3
Click on the [New Project] icon.
h The [New Project] dialog box appears.
“Name” field
[OK] button
4
5
Type a project name in the “Name” field.
h Use any name that is easy to understand.
Click the [OK] button.
h The screen to enter the data to the project appears.
[Get Media] tab
[Project] tab
[Files and
Folders]
6
Click on [Files and Folders].
h The screen to select the data appears.
h Specify the folder that contains the files.
xi English
7
8
Specify the data.
h Select the data by clicking on it.
Click the [Open] button.
h The selected data appears in the [Organizer] window.
h If selecting additional data, click on the [Get Media] tab, and repeat
Steps 6 through 8.
h When you have finished selecting data, proceed to step 9.
9
Click on the [Project] tab.
h The list of your selected data is shown.
[SHARE] tab
Drag
English xii
SHOOT, PLAY BACK AND SAVE
10
Drag and drop the data you wish to burn to the DVD to the
“Timeline/Sceneline” field.
h The data to burn to the DVD appears in the “Timeline/Sceneline” field.
h To include multiple files, repeat step 10 as necessary.
Drop
11 Click the [Create DVD] tab.
h “How would you like to share?” appears.
[SHARE] tab
[Share]
[Disk]
xiii English
12 Click the [Disk].
13 Click the [Burn] button.
h Burning to DVD begins.
14 When writing is complete, press the [Done] button.
15 Click the close button.
h The dialog box to confirm whether to save the project appears.
h If you wish to use the settings for the current project in subsequent
projects, you should save them. If you will not use the settings in
subsequent projects, it is not necessary to save then.
16 Click the [YES] or [NO] button.
h Premiere Elements closes.
English xiv
How was that? The convenient accessories not only let you immediately view
images captured with the camera, but you can also upload images to your
computer and create your original DVDs. Read the following explanations to
find out how you can fully enjoy your camera’s digital movie feature.
xv English
Concerning your camera’s
waterproof feature
Important!
This camera complies with JIS IPX8 (formerly JIS protection grade 8)
waterproof standard and can be used in water. Note, however, that
failing to heed the following precautions may result in damage or injury
that is not covered by the warranty. Please take the time to carefully
read and heed the following cautions.
NOTE
k Before using the camera
i
i
i
When closing the battery/card compartment cover,
make sure that no foreign object such as sand, hair,
dust, etc. is caught in the seal.
Make sure that the battery/card compartment cover is
completely and securely closed to prevent water from
getting inside the camera and damaging it.
Please note that the camera accessories are not
waterproof.
k Cautions concerning use in water
i
The waterproof properties of the camera apply to fresh
water and saltwater only; they do not apply to cleaning
substances, chemicals or water from spas, etc. In
case of a splash, immediately wipe off any moisture.
Do not immerse in water at a depth greater than 1.5 m
(4.92 ft.).
i
i
i
Do not subject the camera to high-pressure water.
Do not immerse in water for longer than 60 minutes.
After 60 minutes of use in water, allow it to dry for at
least 10 minutes.
i
i
Do not immerse in water that is warmer than 40 ºC
(104ºF).
Do not open and close the battery/card compartment
cover when the camera is wet or while it is immersed
in water.
i
i
Do not open and close the battery/card compartment cover with wet hands.
Do not open the battery/card compartment cover on the beach or at the
poolside.
Do not jolt the camera while it is immersed in water. Doing so may cause the
battery/card compartment cover to open.
i
English xvi
NOTE
k Storing and maintaining your camera
i Do not leave the camera unwashed after it has been
immersed in salt water or if salt water is adhering to
it. Doing so may cause corrosion and discoloration of
the plating, as well as deterioration of the camera’s
waterproof capability.
i After the camera has been used in water, use fresh
water to wash it. Never use soap or detergent to
clean the camera, as doing so will cause deterioration
of the camera’s waterproof capability.
i After washing the camera, take care to completely
drain it, and use a dry cloth to wipe off any drops of
water adhering to it (page 67).
i Do not leave the camera in an environment colder than
0 °C (32°F) or warmer than 40 °C (104°F), as doing so
may cause deterioration of the camera’s waterproof
capability.
i Waterproof seals are used in this camera. It is
recommended that the waterproof seals be replaced
every year with new ones. For replacing the seals,
please consult your dealer.
* Please note that there is a fee for replacing the
waterproof seal.
k Other cautions
i Do not subject the camera to severe jolts, as doing so may deform the
battery/card compartment cover or camera body, thus compromising its
waterproof capability. If the camera has been subjected to a strong jolt,
please consult with your dealer.
HINT
What is “JIS IPX8” (formerly “JIS protection grade 8”)?
i “JIS IPX8” specifies that a device is protected against the effects of
continuous immersion in water.
xvii English
CONTENTS
QUICK SEARCH BY OPERATION ........................................................ 6
CHECKING THE INCLUDED ACCESSORIES .................................... 11
How to use the accessories .......................................................... 13
Media cards that can be used with this camera ............................ 15
What “card” means in this manual ................................................ 15
SPECIAL FEATURES .......................................................................... 16
Waterproof capability .................................................................... 16
Movable monitor for any shooting angle ....................................... 17
Capture still shots while recording a video clip ............................. 18
Lots of accessories for optimal use of your captured images ....... 19
SYSTEM MAP ..................................................................................... 20
SETUP
PARTS NAMES ................................................................................... 21
CHARGING THE BATTERY PACK ..................................................... 23
Recharging the battery pack ......................................................... 24
INSTALLING THE BATTERY PACK AND CARD ................................ 25
Install the battery pack .................................................................. 25
Install the card .............................................................................. 28
Warning concerning battery pack temperature ............................. 29
TURNING THE CAMERA ON AND OFF ............................................. 30
Turning on the camera .................................................................. 30
Turning on the camera when the power save (sleep) function is
active ........................................................................................ 30
Turning off the camera .................................................................. 31
DATE AND TIME SETTING ................................................................. 32
SWITCHING BETWEEN THE SHOOTING MODE AND PLAYBACK
MODE .............................................................................................. 35
SWITCHING THE OPERATING MODE .............................................. 36
Switching between the SIMPLE and NORMAL modes ................ 36
Accessing/exiting the SIMPLE/NORMAL Mode Menu Screen ..... 37
Overview of the SIMPLE Mode Setting Screen ............................ 41
Overview of the NORMAL Mode Setting Screen .......................... 45
1
English
SIMPLE
SHOOTING
BEFORE TAKING PICTURES .............................................................53
For best results ..............................................................................53
Using the autofocus .......................................................................54
Select the recording size ...............................................................56
Select the focus setting .................................................................57
Hints for taking pictures .................................................................58
VIDEO CLIP RECORDING ...................................................................59
SHOOTING SINGLE SHOTS ...............................................................60
Using the flash ...............................................................................62
SHOOT A STILL IMAGE WHILE RECORDING A VIDEO CLIP ..........64
MACRO-PHOTOGRAPHY (ZOOM) .....................................................66
AFTER USING THE CAMERA IN WATER ..........................................67
PLAYBACK
PLAYING BACK VIDEO CLIPS AND STILL IMAGES ..........................69
How to save one frame from a video clip as a still image .............71
SLIDESHOW PLAYBACK ....................................................................72
PLAYBACK VOLUME ...........................................................................73
DELETING FILES .................................................................................74
PLAYBACK MODES .............................................................................76
Multi-image display ........................................................................76
Selecting the playback folder ........................................................77
Magnifying (zooming in) the image ...............................................78
English
2
CONTENTS
NORMAL
SHOOTING
RECORDING SIZE .............................................................................. 79
Movies .......................................................................................... 79
Still images ................................................................................... 80
Sequential shots ........................................................................... 81
Audio recording ............................................................................. 82
SCENE SELECT .................................................................................. 85
FILTERS .............................................................................................. 87
FLASH OPERATION ........................................................................... 88
SELF-TIMER ........................................................................................ 89
MOTION COMPENSATION (IMAGE STABILIZER) ............................ 91
Compensate for camera shake during video clip recording .......... 91
Compensate for camera shake during still image shooting .......... 91
FOCUS RANGE ................................................................................... 94
How to use the manual focus ....................................................... 95
FOCUS MODE ..................................................................................... 96
LIGHT-MEASURING MODE SETTING ............................................... 97
ISO SENSITIVITY ................................................................................ 98
WHITE BALANCE ................................................................................ 99
FACE CHASER ................................................................................. 100
HIGH SENSITIVITY MODE ............................................................... 101
DIGITAL ZOOM SETTING ................................................................. 102
SPECIFY A FOLDER TO SAVE FILES ............................................. 103
EXPOSURE COMPENSATION ......................................................... 104
3
English
PLAYBACK
SLIDESHOW PLAYBACK ..................................................................105
FILE PROTECT ..................................................................................107
ROTATE STILL IMAGE ......................................................................108
REDUCE STILL IMAGE SIZE (RESIZE) ............................................109
CORRECTING THE RED-EYE EFFECT AND IMAGE BLUR ............110
EDITING VIDEO CLIPS ......................................................................112
Procedure to cut (extract) a portion of a video clip ......................112
Procedure to join video clips .......................................................113
Video clip cutting (extracting) ......................................................114
Joining video clips .......................................................................117
PRINTING INSTRUCTIONS ...............................................................120
Display the Printing Instructions Screen ......................................120
Specifying date imprinting and print quantities ............................122
Index print ....................................................................................124
Clearing all the printing instructions ............................................125
COPY FILES .......................................................................................126
DISPLAYING FILE PROPERTIES (INFORMATION SCREEN) .........128
OPTION SETTINGS
DISPLAY THE OPTION SETTING MENU .........................................129
SCREEN DISPLAY .............................................................................130
SELECT THE STARTUP DISPLAY ....................................................131
OPERATION SOUNDS ......................................................................132
POST-VIEW DISPLAY SETTING .......................................................134
ASSIGN FUNCTIONS TO THE ARROW BUTTONS .........................135
NOISE-REDUCTION FUNCTION ......................................................137
ADJUST THE IMAGE QUALITY .........................................................138
FLICKER-REDUCTION ......................................................................139
MONITOR BRIGHTNESS ..................................................................140
SCREEN LANGUAGE ........................................................................141
TV SYSTEM SETTING .......................................................................142
POWER SAVE FUNCTION ................................................................143
FILE NO. MEMORY ............................................................................145
INITIALIZING THE CARD MEMORY AND INTERNAL MEMORY .....148
RESETTING THE CAMERA SETTINGS ............................................150
CHECKING THE REMAINING CARD MEMORY ...............................151
Checking the remaining number of images and
video recording time ................................................................151
For audio recordings ...................................................................151
CHECKING THE REMAINING BATTERY PACK CHARGE ..............153
English
4
CONTENTS
OTHER DEVICES AND CONNECTIONS
CONNECTING TO A TV
CONNECTING TO A TV .................................................................... 155
PLAYING BACK ON A TV ................................................................. 156
CONNECTING TO A PRINTER
PictBridge MODE ............................................................................... 157
Print preparations ....................................................................... 157
PRINTING .......................................................................................... 159
Printing selected images ............................................................. 159
Printing all images ...................................................................... 160
Making an index print .................................................................. 161
Printing images according to printing instructions
(requested images) ................................................................ 162
Changing the printer settings ...................................................... 163
APPENDICES
COMMONLY ASKED QUESTIONS ................................................... 165
TROUBLESHOOTING ....................................................................... 172
Camera ....................................................................................... 172
Notes regarding the Scene Select feature and filters ................. 182
SPECIFICATIONS ............................................................................. 184
Camera ....................................................................................... 184
Camera connectors .................................................................... 188
Battery life ................................................................................... 188
Possible No. of Images/Possible Shooting Time/
Possible Recording Time ....................................................... 189
Concerning the multi-indicator .................................................... 190
Supplied battery pack charger .................................................... 191
Supplied Li-ion battery pack ....................................................... 191
Others ......................................................................................... 192
Before capturing those important shots, be sure to first take
a test shot to confirm that your camera is set up and
ready to go ............................................................................. 193
HINTS FOR TAKING PICTURES ...................................................... 194
5
English
QUICK SEARCH BY OPERATION
Your camera has an abundance of convenient features and functions. From
creating precisely the photo you want, to viewing images using various
techniques, you can locate the exact operation for your purposes in the
following table.
Shooting/recording
Basic operation
Convenient functions Additional functions
Log the date and time For more accurate
Getting started
shooting/recording
of your photos
focus
• “How to use the manual
•
“VIDEO CLIP
•
“DATE AND TIME
RECORDING” on
page 59
“SHOOTING SINGLE
SHOTS” on page 60
“Sequential shots” on
page 81
SETTING” on page 32
focus” (manual focus) on
page 95
Set the focus to a
narrow range
“FOCUS MODE” on
page 96
Reduce noise when
recording
“NOISE-REDUCTION
Zoom in on the
subject
“MACRO-
PHOTOGRAPHY
(ZOOM)” on page 66
Close-up
•
•
•
•
•
“Audio recording” on
page 82
photography
•
“Select the focus setting”
(super macro mode) on
page 57
•
FUNCTION” on page 137
•
“FOCUS RANGE” (super
macro mode) on page 94
Optimize the photo
quality
Reduce video clip flicker
“FLICKER-REDUCTION” on page 139
•
Set the camera’s color/contrast
characteristics
•
“Select the recording
size” on page 56
“RECORDING SIZE” on
page 79
•
•
“ADJUST THE IMAGE QUALITY” on page 138
English
6
QUICK SEARCH BY OPERATION
Shooting/recording
Basic operation
Convenient functions Additional functions
Capture fast-moving subjects
•
“SCENE SELECT” (sports mode) on page 85
Suppress camera shake effect
•
•
“Compensate for camera shake during video clip recording” on page 91
“Compensate for camera shake during still image shooting” on page 91
Shoot in dark conditions
•
•
•
•
“EXPOSURE COMPENSATION” on page 104
“Using the flash” on page 62
“FLASH OPERATION” on page 88
“SCENE SELECT” (night view portrait mode/fireworks mode/lamp mode) on page 85
Increase the camera’s sensitivity
•
•
“ISO SENSITIVITY” on page 98
“HIGH SENSITIVITY MODE” on page 101
Photographing people
•
•
“SCENE SELECT” (portrait mode/night view portrait mode) on page 85
“FILTERS” (cosmetic filter) on page 87
Sharp face shots
“FACE CHASER” on page 100
•
Simplified operation for shooting/playback
“Switching between the SIMPLE and NORMAL modes” on page 36
•
Photographing landscapes
“SCENE SELECT” (landscape mode/underwater mode) on page 85
•
Take a self-photo
•
“SELF-TIMER” on page 89
Make images lighter
or darker
Measure the
brightness of a
specific area
“LIGHT-MEASURING
MODE SETTING” on
page 97
•
“EXPOSURE
COMPENSATION” on
page 104
•
•
“HIGH SENSITIVITY
MODE” on page 101
Adjust the camera’s
sensitivity
•
“ISO SENSITIVITY” on
page 98
Change the color of
the images
“FILTERS” (monochrome
filter/sepia filter) on
page 87
Make white appear
natural
•
•
“WHITE BALANCE” on
page 99
7
English
Playback
Basic operation
Convenient functions Additional functions
Getting started
viewing images
Adjust the speaker
volume
Change the angle of
view
•
“PLAYING BACK VIDEO
CLIPS AND STILL
•
“PLAYBACK VOLUME”
on page 73
•
“ROTATE STILL IMAGE”
on page 108
IMAGES” on page 69
Search for image/
audio files
•
“Multi-image display” on
page 76
•
“Selecting the playback
folder” on page 77
Magnify an image
•
“Magnifying (zooming in)
the image” on page 78
•
“Audio playback” on
page 83
Adjust the speaker volume
“PLAYBACK VOLUME” on page 73
•
Continuous playback
“SLIDESHOW PLAYBACK” on page 72 and 105
•
Adjust the monitor brightness
“MONITOR BRIGHTNESS” on page 140
•
Set the TV system
“TV SYSTEM SETTING” on page 142
Playback on a TV
“CONNECTING TO A TV” on page 155 and “PLAYING BACK ON A TV” on page 156
•
•
English
8
QUICK SEARCH BY OPERATION
File managing/processing
Basic operation
Convenient functions Additional functions
Search for image/audio files
•
•
“Multi-image display” on page 76
“Selecting the playback folder” on page 77
Delete files
Protect files from accidental erasure
“FILE PROTECT” on page 107
Format a card
•
“DELETING FILES” on
page 74
•
•
“INITIALIZING THE CARD MEMORY AND INTERNAL
MEMORY” on page 148
Delete a part of a video clip and join video clips
“EDITING VIDEO CLIPS” on page 112
•
Specify the number of prints, index print, and date imprint
“PRINTING INSTRUCTIONS” on page 120
•
Repair the “red-eye” caused by the flash, or enhance the contrast
“CORRECTING THE RED-EYE EFFECT AND IMAGE BLUR” on page 110
•
View the settings that were in effect when the image/audio files were
recorded
•
“DISPLAYING FILE PROPERTIES (INFORMATION SCREEN)” on page 128
9
English
Using with a computer
Basic operation
Convenient functions Additional functions
Use the camera as a card reader
•
“USING AS A CARD READER” on page 11 in the Xacti Software DVD INSTRUCTION
MANUAL
Copy data from your
camera to a computer
“Copy data from your
camera to the computer”
on page viii
Using with Windows Vista
•
“SETTING THE CONNECTION MODE” on page 9 in
the Xacti Software DVD INSTRUCTION MANUAL
•
•
“OPERATING
ENVIRONMENT” on
page 5 in the Xacti
Software DVD
INSTRUCTION MANUAL
•
“SETTING THE
CONNECTION MODE”
on page 9 in the Xacti
Software DVD
INSTRUCTION MANUAL
Playback
•
“About video clip files recorded with this camera” on page 8 in the Xacti Software DVD
INSTRUCTION MANUAL
•
“INSTALLING THE APPLICATION SOFTWARE” on page 15 in the Xacti Software
DVD INSTRUCTION MANUAL
Using as a webcam
•
“USING AS A PC CAMERA” on page 14 in the Xacti Software DVD INSTRUCTION
MANUAL
Record an image of the computer screen
•
“SCREEN CAPTURE” on page 20 in the Xacti Software DVD INSTRUCTION
MANUAL
Create a DVD
•
•
“Burn your recorded video clips onto a DVD (Windows XP)” on page vii
“INSTALLING THE APPLICATION SOFTWARE” on page 15 in the Xacti Software
DVD INSTRUCTION MANUAL
•
“ABOUT Premiere Elements” on page 17 in the Xacti Software DVD INSTRUCTION
MANUAL
English 10
CHECKING THE INCLUDED
ACCESSORIES
i Handstrap and soft case
(pages 13 and 14): 1 set
i Xacti Software DVD (DVD-
ROM) (page 4 in the Xacti
Software DVD INSTRUCTION
MANUAL): 1
i Li-ion battery pack (pages 23
and 25): 1
i Lithium-ion battery pack
charger (page 23): 1
i
Dedicated USB interface cable
(page 157, page 9 in the Xacti
Software DVD INSTRUCTION
MANUAL): 1
i Dedicated AV interface cable
(page 155): 1
11 English
i QUICK GUIDE
i SAFETY MANUAL
(safety precautions booklet)
Please read this booklet
carefully before using the
camera.
English 12
CHECKING THE INCLUDED ACCESSORIES
How to use the accessories
k Handstrap
13 English
k Soft case
English 14
CHECKING THE INCLUDED ACCESSORIES
Media cards that can be used with this camera
The type of card that can be inserted into and used with this camera is:
i SD Memory Card
i SDHC Memory Card
What “card” means in this manual
i In this manual, SD Memory Cards and SDHC Memory Cards that can be
used in this digital camera are referred to as “card”.
15 English
SPECIAL FEATURES
Your movie camera can not only record video clips, you can also take still
photos and make audio recordings. For example, you can snap a still image
while recording a video clip, or make just an audio recording.
Waterproof capability
The camera is equipped to safely be used in water at a temperature of
less than 40 ºC (104ºF), at a depth of less than 1.5 m (59 in.), for up to
approximately 60 minutes. You can enjoy taking pictures at the beach or
by the pool.
English 16
SPECIAL FEATURES
Movable monitor for any shooting angle
The movable monitor lets you shoot from any angle. Hold the camera
high to get a great view of a parade, or swivel the monitor around to
snap a photo of yourself.
If you swivel the
monitor unit to its
farthest position, the
image on the monitor
will be inverted.
17 English
Capture still shots while recording a video clip
(page 64)
Suppose that while you’re recording a video clip, there’s a scene you’d
like to keep as a still photo. Your camera makes it possible to record the
still photo without interrupting the video clip recording.
01:17:32
English 18
SPECIAL FEATURES
Lots of accessories for optimal use of your
captured images (page 20)
Use the accessory cables to view images on a TV or computer. Or
connect the camera directly to a printer to make prints of your photos.
And with the software in the supplied DVD-ROM (Xacti Software DVD),
you can create your original DVDs and CDs.
19 English
SYSTEM MAP
You can connect the camera to various devices to expand its capabilities.
Internet
Computer
Dedicated USB
interface cable
Printer
Dedicated AV
interface cable
TV
DC adaptor
(Optional)
AC adaptor
(Optional)
i Card reader
i DPOF-compatible
printer
Commercially available
SD Memory Card
i Photo shop
English 20
SETUP
SETUP
PARTS NAMES
Front
Flash
Stereo microphone
Lens
Speaker
REC/PLAY button
Monitor unit
To open
ON/OFF button
Strap holder
There are places in the camera where water might accumulate, but this will
not affect its waterproof properties.
Concerning the drainage holes, see page 67.
21 English
Rear
[
] button
[
] button
MENU button
[T/]] button
[H] button
[G] button
[W/P] button
SET button
Multi-indicator
Battery/card
compartment cover
Monitor
Tripod stand hole
English 22
CHARGING THE BATTERY PACK
Please charge the supplied battery pack before using it.
1
2
3
Insert the battery pack in the
battery charger.
h Insert it in the direction
indicated by the [o] mark
on the battery pack.
CHARGE indicator
[o] mark
Battery pack
Socket
To power outlet
Connect the supplied power
cord to the socket on the
battery pack charger.
h Insert the connector straight
and securely.
Power cord
Plug the power plug into a
power outlet (AC 100 V to
240 V).
CHARGE indicator
h Charging begins.
h During charging, the
CHARGE indicator is lit red.
h The charging time is approx.
90 minutes.
4
When the CHARGE indicator
turns off, unplug the power
cord from the power outlet,
and remove the battery pack
from the charger.
23 English
Recharging the battery pack
Be sure to fully charge the supplied or separately sold battery pack
before using it in your camera. For charging the battery pack, use the
supplied charger.
Charge the battery pack if it is being used for the first time, and
recharge it whenever the remaining charge is low (see“CHECKING THE
REMAINING BATTERY PACK CHARGE” on page 153).
If there is interference to your TV or radio during recharging...
i Move the battery pack and charger further away from the TV or radio.
Ambient temperature during recharging
i During recharging, the charger and battery pack will be warm. This is
normal and does not indicate a malfunction.
i It is recommended that the ambient temperature during recharging be
between about 0 °C and 40 °C (32°F and 104°F). Due to the
characteristics of the battery pack, at temperatures below 0 °C (32°F), it
may not be possible to sufficiently recharge it.
i When the battery pack temperature is high, it may take longer to recharge
it.
Recharge a battery pack in the following cases
i A battery pack which has not been used for a long time
i Newly purchased battery pack
English 24
INSTALLING THE BATTERY PACK
AND CARD
Make sure that the battery pack and the card orientation are correct.
Install the battery pack
1
Open the battery/card compartment
cover.
Lever
h While gently pressing the lever,
open the battery/card compartment
cover.
1 Push
2 Open
2
Insert the battery pack.
h Press the latch, insert the battery
pack, and firmly push it all the way
in.
Battery pack slot
1 Press the latch
Bottom side
2 Insert
25 English
<To remove the battery pack...>
h Press the latch securing the battery
pack, and remove the battery pack.
1 Press the latch
2 Pull out
3
Close the battery/card compartment
cover.
Press the PUSH LOCK part
to securely close the cover.
h Press the PUSH LOCK part to
close the cover securely.
h At the time of purchase the battery
pack is not charged. Be sure to fully
charge the battery pack (page 23).
English 26
INSTALLING THE BATTERY PACK AND CARD
CAUTION
Close the battery/card compartment cover securely
i If the battery/card compartment cover is not closed or is not closed
completely, the camera will no longer be waterproof. When closing the
battery/card compartment cover, make sure that no foreign object such as
sand, hair, dust, etc. is caught in the seal.
Do not charge the battery pack immediately after the camera has been
in continuous use for a long time
i The battery pack becomes hot when the camera is used continuously for a
long time. If you attempt to charge the battery pack in this state, the charge
indicator may flash red and it may not be possible to charge the battery
pack. Wait until the battery pack has cooled down before attempting to
charge it.
Does the battery pack appear swollen?
i The lithium-ion battery used in this camera may expand slightly when
stored in a hot environment or repeatedly used, but this is not a safety
hazard.
HINT
About the internal backup battery
i This camera’s internal battery serves to maintain the date and time
settings, as well as the shooting settings. The backup battery will be fully
charged when the battery pack is kept in the camera continuously for about
2 days. In the fully charged state, the backup battery will maintain the
camera settings for about 7 days.
When not using the camera for a long time, remove the battery pack
i A small amount of power is still used even if the camera is turned off, and it
is therefore recommended that the battery pack be removed from the
camera if it is not going to be used for a long time. Note that when the
battery pack is removed for a long period, the time and date settings may
be cleared. Before using your camera again, be sure to confirm that the
camera settings are correct.
To prolong the life of the battery pack
i Although the battery pack is an expendable item, you can maximize the life
of the battery by heeding the following suggestions.
h Do not leave the battery under the hot summer sun or exposed to other
high-temperature environments.
h Do not continually recharge the battery when it is already fully charged.
After fully charging it once, for example, use it for a while to partially
discharge it before recharging it again.
h When the battery is not to be used for a long time, if possible store the
partially charged (not fully charged) battery in a cool environment.
27 English
Install the card
The card can be used after it has been formatted with the camera
(page 148).
1
2
Open the battery/card
compartment cover.
Card slot
Insert the card.
h Firmly insert the card until it
clicks into place.
1 Open
2 Insert
3
Close the battery/card compartment cover.
<When removing the card...>
1 Open
h To remove the card, press it
2 Push
down, and then release. The
card will protrude slightly, and
you can then pull it out.
3 Pull out
English 28
INSTALLING THE BATTERY PACK AND CARD
CAUTION
Do not attempt to forcibly remove the card
i Never remove the card when the multi-indicator is flashing red. In doing so,
you risk losing the data stored in the card.
HINT
Shooting without a card installed
i When a card is installed, images are recorded to and played back from the
card. When no card is installed, images are recorded to and played back
from the camera’s internal memory. When the camera is turned on with no
card installed, the internal memory icon
is shown on the monitor to let
you know that the images you capture will be saved to the camera’s
internal memory.
Warning concerning battery pack temperature
i If the battery pack in the camera becomes too hot, a blinking temperature
warning icon \ will appear on the monitor. If the blinking icon does
appear, the camera should be turned off as soon as possible and the
battery pack allowed to cool before the camera is turned on again.
i Note that the camera will turn off automatically if it continues to be used
with the battery pack temperature elevated.
i If you attempt to turn on the camera when the battery pack temperature is
too high, the temperature warning icon will blink and the camera will not
turn on.
29 English
TURNING THE CAMERA ON AND OFF
Turning on the camera
1
Open the monitor unit, and press the
ON/OFF button for at least 1 second.
h If you press the REC/PLAY button for
at least 1 second, the camera turns
on in the playback mode.
Monitor unit
h If you press the ON/OFF button once,
the camera will switch to the power
save mode.
ON/OFF button
Turning on the camera when the power save
(sleep) function is active
In order to preserve battery pack power, the power save (sleep) function
will automatically turn off the camera after 1 minute of no use during
shooting, or 5 minutes of no use during playback (factory-preset
setting).
i When the power save function is active, you can restore the power by any
of the following methods:
h Press the ON/OFF button.
h Press the [
] or [
] button.
h Open the monitor unit.
h Press the SET button.
i The camera will switch to the standby mode after the power save function
has been active for about 1 hour, or when you close the monitor unit.
i The power save mode will not be activated while you are recording.
i The user can specify the time elapsed before the power save function is
activated (page 143).
i When the camera is connected to a computer or printer using the
dedicated USB interface cable, the power save function is disabled, and
the camera turns off after about 12 hours.
English 30
TURNING THE CAMERA ON AND OFF
Turning off the camera
1
Press the ON/OFF button for at least 1 second.
h The camera turns off.
h To turn off the camera while it is in the shooting mode or power save
mode, press the ON/OFF button for at least 1 second.
HINT
To immediately activate the power save
function
i Press the ON/OFF button briefly to
activate the power save function.
If the date and time setting has been
completed (page 32)...
i The current time is shown on the monitor
when the camera is turned on.
About the standby mode
i To turn off the camera only briefly, you
can close the monitor unit to put the
camera in the standby mode. The standby
mode uses almost no power. When the
monitor unit is opened again, the camera
turns on immediately and you are ready to
shoot or view images without any delay.
CAUTION
If the K icon appears...
i When a picture is taken, the date and time it was captured are recorded
with it. If the date and time settings have not been completed (page 32),
the date and time cannot be recorded with the captured images. For this
reason, immediately after the camera is turned on, the “Set date and time”
screen appears. To have the date and time recorded with the images,
please complete this setting before capturing images.
31 English
DATE AND TIME SETTING
The camera will record the date and time an image or audio recording is
taken so that you can display them during playback. Therefore, before
capturing images, make sure the correct date and time are set.
* To correct the date and time setting, please see under HINT on page 34.
Example: To set the clock to 7:30 p.m. on December 24, 2008
1
Turn on the camera (page 30), and
press the SET button.
SET button
h The Clock Set Screen appears.
h Follow the procedures below to
enable or disable the date display
during playback, to set the display
format for the date, and to set the
date and time.
MENU button
h To display the Recording or
Playback Screen, press the
MENU button 2 times.
CLOCK SET
DATE
TIME
DISP
2008/05/01
00:00
Y / M / D
OK
English 32
DATE AND TIME SETTING
2
Set the date.
1 Select “DATE”.
2 Press the SET button.
h The Set Date Screen
appears.
CLOCK SET
DATE
2008/12/24
3 Set the date to “2008/12/24”.
h The date is set in the
following order: Set the year
→ Set the month → Set the
day.
OK
h Press the [G] or [H] button to
select year, month or day.
Press the [T/]] or [W/P]
button to increase or decrease
the number.
4 Press the SET button.
3
Set the clock.
1 Select “TIME”.
2 Press the SET button.
h The Set Time Screen
appears.
CLOCK SET
TIME
19:30
3 Set the time to “19:30”.
h The time is set in the
following order: Set the hour
→ Set the minute.
OK
h A 24-hour clock is used for
the time display.
4 Press the SET button.
33 English
4
Set the order in which the date is
displayed during playback.
1 Select “DISP”.
CLOCK SET
2 Press the SET button.
h The Set Date Format Screen
appears.
DISP
Y / M / D
OK
3 Press the [T/]] or [W/P]
button.
h Press the [T/]] button to
change the displayed date
order as follows:
Y / M / D → M / D / Y → D / M / Y
Press the [W/P] button to change it in the reverse order.
4 Press the SET button.
5
Press the MENU button.
h The date and time setting is completed.
h To display the Recording or Playback Screen, press the MENU button.
HINT
About the settings backup
i Under normal conditions, while the battery pack is being replaced, an
internal battery will maintain the date and time settings. However, there is a
small chance the settings may be lost (the backup will last for about
7 days). It is recommended to check that the date and time settings are still
correct after replacing the battery pack and before shooting or recording of
any type (follow step 1).
To correct the date and time settings
1 Turn on the camera.
2 Display the Option Setting Menu [E1] (page 129).
3 Select “CLOCK SET” and press the SET button.
h The screen to set the date and time appears.
h The current date and time settings are shown.
4 Select the line you wish to change, and make the correction.
English 34
SWITCHING BETWEEN THE SHOOTING
MODE AND PLAYBACK MODE
Switch between the shooting mode (for recording) and the playback mode (for
viewing your recorded images).
1
2
Turn on the camera (page 30).
Press the REC/PLAY
button.
h The mode changes.
h The mode changes each
time the REC/PLAY button
is pressed.
668
01:17:32
REC/PLAY button
<Example of the shooting
mode>
SAVE
PPLLAAYY
<Example of the playback
mode>
35 English
SWITCHING THE OPERATING MODE
The “SIMPLE mode” comprises only those functions that are most often used
and necessary to operate the camera, while the “NORMAL mode” enables
full use of all the camera’s many functions. Select the mode that is suitable for
your purposes.
Switching between the SIMPLE and NORMAL
modes
1
2
3
Turn on the camera (page 30).
h The previous mode is active.
Press the MENU button.
h The Menu Screen for the active mode appears.
Select the operating mode icon,
and press the SET button.
h Switch from the SIMPLE mode
to the NORMAL mode, or from
the NORMAL mode to the
Switch to detailed
normal menu
SIMPLE mode.
h Press the MENU button to
cancel the Menu Screen.
EXIT
OK
S
N
Operating mode icon
<SIMPLE Mode Menu Screen>
1
2
3
1
2
Switch to
simple menu
3
S
N
EXIT
OK
Operating mode icon
<NORMAL Mode Menu Screen>
English 36
SWITCHING THE OPERATING MODE
Accessing/exiting the SIMPLE/NORMAL Mode
Menu Screen
1
2
3
Set the camera to the shooting or playback mode (page 35).
Select the desired operating mode (page 36).
If the Menu Screen is not displayed, press the MENU button.
h The Menu Screen appears.
h To cancel the Menu Screen, press the MENU button.
MENU button
Switch to detailed
normal menu
OK
S
N
EXIT
<Example: SIMPLE Mode
Shooting Menu>
1
2
3
1
2
Switch to
simple menu
3
S
N
EXIT
OK
<Example: NORMAL Mode
Shooting Menu>
37 English
Using the SIMPLE Mode Menu
4
Press the [T/]] or [W/P] button to select the item you wish to
change, and press the SET button.
h The Setting Screen for the selected item appears.
Select an item to change
Description of selected
item
Press
Select movie and
photo size
S
N
EXIT OK
Press
Press
To watch on TV
8
TV size
8M [4:3]
EXIT OK
<Setting Screen>
English 38
SWITCHING THE OPERATING MODE
Using the NORMAL Mode Menu
4
Press the [T/]] or [W/P] button to select a tab.
h The Menu Screen for the selected tab appears.
Tab
Press
RECORDING MENU1
MOVIE
PHOTO
SCENE SELECT
FILTER
FLASH
SELF-TIMER
EXIT OK
1
2
3
1
2
3
S
N
Press
5
Press the [H] button.
RECORDING MENU 1
MOVIE
1
Press
2
3
1
2
3
PHOTO
SCENE SELECT
FILTER
FLASH
SELF-TIMER
EXIT OK
S
N
39 English
6
Press the [T/]] or [W/P] button to select the item you wish to
change, and press the SET button.
h The Setting Screen for the selected item appears.
h To return to the Menu Screen, press the MENU button.
Select an item to change
Press
RECORDING MENU
MOVIE
1
1
2
3
1
2
3
PHOTO
SCENE SELECT
FILTER
FLASH
SELF-TIMER
EXIT OK
S
N
Press
Press
Applicable mode
PHOTO
4000×3000
3264×2448
3264×2448
3264×1840
1840×2448
[
]
16:9
OK
<Setting Screen>
HINT
About the applicable mode indicator
i This indicator shows the shooting mode(s) for which the selected setting is
effective.
: This setting is effective during still image shooting.
: This setting is effective during video clip recording.
: This setting is effective during still image shooting and video clip
recording.
English 40
SWITCHING THE OPERATING MODE
Overview of the SIMPLE Mode Setting Screen
SIMPLE Mode Shooting Menu
Select movie and
1
photo size
2
3
4
5
S
N
EXIT
OK
41 English
1 Recording size (page 56)
h Select the video clip size to
record, and the still image size
to shoot.
3 Flash (page 62)
h Specify how the flash will
operate.
9: The camera detects the
subject brightness and
uses the flash only when
necessary.
:: The flash operates with
every image captured
regardless of the
T
: The video clip size will be
640 × 480 pixels, and the still
image size will be 3264 × 2448
pixels.
conditions.
;: The flash does not operate
even in dark situations.
6
: The video clip size will be
320 × 240 pixels, and the still
image size will be 640 × 480
pixels.
4
(page 36)
h Set to the NORMAL mode.
5 Remaining battery power
2 Focus range (page 57)
h Select the focus range that
corresponds to the distance to
the subject.
indication (page 153)
7: The camera automatically
focuses on the subject
within a range of 10 cm
(3.94 in.) to infinity
(normal).
8: The camera focuses on a
subject within a range of
1 cm (0.39 in.) to 80 cm
(31.50 in.) (super macro).
English 42
SWITCHING THE OPERATING MODE
SIMPLE Mode Playback Menu
1
2
3
S
N
Start slideshow
OK
5
4
43 English
1 Slideshow (page 72)
h Specify the slideshow settings
and play the slideshow.
3 Delete (page 74)
h Delete files.
4
(page 36)
2 Playback volume (page 73)
h Adjust the volume for video
clip and audio file playback.
h Set to the NORMAL mode.
5 Remaining battery power
indication (page 153)
English 44
SWITCHING THE OPERATING MODE
Overview of the NORMAL Mode Setting Screen
NORMAL Mode Shooting Menu
<Tab 1>
1
RECORDING MENU
MOVIE
PHOTO
SCENE SELECT
FILTER
FLASH
1
1
2
3
4
5
6
7
2
3
1
2
3
SELF-TIMER
8
S
N
EXIT
OK
45 English
1 Video clip settings (page 79)
(: Record at 640 × 480 pixels,
60 frames per second.
3 Scene select (page 85)
=: Full auto setting
a: Sports mode
): Record at 640 × 480 pixels,
30 frames per second (high
bit rate).
>: Portrait mode
+: Landscape mode
/: Night view portrait mode
k: Snow & beach mode
[: Underwater mode
+: Fireworks mode
Q: Lamp mode
B: Record at 640 × 480 pixels,
30 frames per second
(standard bit rate).
l: Record at 320 × 240 pixels,
30 frames per second.
d: Record at 320 × 240 pixels,
15 frames per second.
4 Filter (page 87)
&: No filter
%: Cosmetic filter
W: Monochrome filter
,: Sepia filter
<: Make an audio recording.
2 Still image settings (page 80)
I: Image size is 4000 × 3000
pixels.
5 Flash (page 88)
k: The camera will detect the
subject brightness and use
the flash only when
U: Image size is 3264 × 2448
pixels (low compression).
V: Image size is 3264 × 2448
pixels (normal
necessary.
compression).
m: The flash will operate with
every image captured
regardless of the
conditions.
l: The flash will not operate
even in dark situations.
]: Image size is 3264 × 1840
pixels (16:9 aspect ratio).
W: Image size is 1840 × 2448
pixels (portrait orientation).
G: Image size is 1600 × 1200
pixels.
6 Self-timer (page 89)
N: Self-timer is off.
[: Image size is 640 × 480
pixels.
y: Shooting begins 2 seconds
R: 3264 × 2448-pixel
sequential shots.
t: 1600 × 1200-pixel
sequential shots.
after the [
] or [
]
button is pressed.
x: Shooting begins
10 seconds after the [
]
or [
] button is pressed.
7 Remaining battery power
(page 153)
8
(page 36)
S
N
h Set to the SIMPLE mode.
English 46
SWITCHING THE OPERATING MODE
<Tab 2>
RECORDING MENU2
MOVIE STABILIZER
PHOTO STABILIZER
FOCUS
FOCUS MODE
EXP MEASURE
1
1
2
3
4
5
6
7
2
3
1
2
3
ISO
8
S
N
EXIT
OK
47 English
1 Movie stabilizer (page 91)
h Compensate for camera shake
during video clip recording.
5 Light-measuring mode
(page 97)
X: Multi-section light
measuring
W: Center-weighted light
measuring
p: Shoot using the video clip
field of view display.
q: Shoot using the still image
field of view display.
Y: Spot light-measuring
]: Image stabilizer function
6 ISO sensitivity (page 98)
=: Sensitivity is set
off.
2 Photo stabilizer (page 91)
h Compensate for camera shake
during still image shooting.
\: Shoot with image stabilizer
on.
]: Shoot without image
stabilizer.
3 Focus range (page 94)
h Select the focus range that
corresponds to the distance to
the subject.
automatically
*: Sets sensitivity to ISO 50
u: Sets sensitivity to ISO 100
v: Sets sensitivity to ISO 200
w: Sets sensitivity to ISO 400
6: Sets sensitivity to ISO 800
-: Sets sensitivity to ISO 1600
* The indicated ISO value is the
standard output sensitivity.
7 Remaining battery power
-: The camera automatically
focuses on the subject
within a range of 10 cm
(3.94 in.) to infinity (total
range).
(page 153)
8
(page 36)
S
N
h Set to the SIMPLE mode.
*: The camera automatically
focuses on the subject
within a range of 80 cm
(31.50 in.) to infinity
(normal).
-: Set the focus distance
manually (manual).
+: The camera focuses on the
subject within a range of
1 cm (0.39 in.) to 80 cm
(31.50 in.) (super macro).
4 Focus mode (page 96)
B: 9-point range finder focus
C: Spot focus
English 48
SWITCHING THE OPERATING MODE
<Tab 3>
RECORDING MENU3
WHITE BALANCE
FACE CHASER
HIGH SENSITIVITY
DIGITAL ZOOM
REC FOLDER
1
1
2
3
4
5
2
3
1
2
3
7
6
EXIT
OK
S
N
49 English
1 White balance (page 99)
>: White balance is
automatically adjusted
depending on the ambient
lighting (auto).
3 High sensitivity mode
(page 101)
1: Increased sensitivity
2: Normal sensitivity
4 Digital zoom (page 102)
Q: Enable the digital zoom.
B: Disable the digital zoom.
r: For shooting in sunny
conditions (fair)
o: For shooting in overcast
conditions (cloudy)
p: For shooting under
fluorescent lighting
5 Recording folder (page 103)
h Create or select a folder in
which to store recorded files.
(fluorescent)
6 Remaining battery power
indication (page 153)
q: For shooting under
incandescent lighting
(incandescent)
7
(page 36)
S
N
h Set to the SIMPLE mode.
^: For setting the most
accurate white balance
(one push)
2 Face chaser (page 100)
-: Enable face chaser.
.: Disable face chaser.
English 50
SWITCHING THE OPERATING MODE
NORMAL Mode Playback Menu
<Tab 1>
PLAYBACK MENU
SLIDESHOW
PLAY VOLUME
PROTECT
1
1
1
2
3
4
5
6
7
2
1
2
3
DELETE
ROTATE
RESIZE
EXIT
8
S
N
OK
1 Slideshow (page 105)
h Specify the slideshow settings
and play the slideshow.
4 Delete (page 74)
h Delete files.
5 Rotate (page 108)
h Rotate a still image.
6 Resize (page 109)
2 Playback volume (page 73)
h Adjust the volume for video
clip and audio files playback.
h Reduce the resolution of a still
image.
3 Protect (page 107)
h File protect setting (delete
prohibited)
7 Remaining battery power
(page 153)
8
(page 36)
S
N
h Set to the SIMPLE mode.
51 English
<Tab 2>
PLAYBACK MENU2
EDIT PHOTO
1
1
2
3
4
5
2
EDIT VIDEO
1
2
3
PRINT INSTRUCTIONS
SELECT FOLDER
COPY
7
6
S
N
EXIT
OK
1 Edit photo (page 110)
h Repair the “red-eye” caused
by the flash, or enhance the
contrast.
2 Video clip edit (page 112)
h Edit video clips.
4 Select folder (page 77)
h Select a folder to play back.
5 Copy (page 126)
h Copy files from the card to the
internal memory, or vice versa.
6 Remaining battery power
indication (page 153)
3 Printing instructions
(page 120)
h Specify the printing
7
(page 36)
S
N
h Set to the SIMPLE mode.
instructions (DPOF settings).
English 52
SIMPLE
SHOOTING
SIMPLE/SHOOTING
BEFORE TAKING PICTURES
For best results
Hold the camera securely, keeping your elbows close to your body and
making sure the camera is stable.
Correct hold
Incorrect hold
<Holding the camera>
A finger is blocking the
lens or flash.
Example 1:
Grip the camera by wrapping
the fingers of the right hand,
from the little finger to the
middle finger, around the
camera, and hook the index
finger above the lens.
Example 2:
Grip the camera by wrapping
the fingers of the right hand,
from the little finger to the index
finger, around the camera.
Make sure that the lens and flash are not blocked by your fingers or the
handstrap.
* For shooting vertically oriented still images, you can set the shooting
orientation to the vertical (portrait) format (page 80).
53 English
Using the autofocus
The autofocus will work in almost all situations; however, there are
certain conditions that may cause the autofocus function to not work
properly. If the autofocus function is not working properly, set the focus
range to capture images (page 57).
k Conditions that may cause incorrect focus
The following examples are some of the situations where the autofocus
function may not work.
i Subjects with low contrast, very
bright subjects at the center of the
image or dark subjects or locations
Use the focus-lock function to lock the
focus on an object with contrast at the
same distance as the desired subject.
i Subjects without vertical lines
Use the focus-lock function to lock the
focus while framing the subject
vertically, then re-orient the camera to
compose a horizontally framed image.
English 54
BEFORE TAKING PICTURES
The following examples are some of the situations where the autofocus
function may work, but not as desired.
i When both near and far objects are
present
Use the focus-lock function to lock the
focus on an object at the same distance
as the desired subject, then reposition
the camera to compose the picture.
i Fast-moving subjects
Use the focus-lock function to lock the
focus on an object at the same distance
as the desired subject, then reposition
the camera to compose the picture.
HINT
i Images captured in the still image shooting mode can be rotated when
they are played back (page 108).
i When the [
] button is pressed halfway, the image in the monitor may
waver vertically. This is the result of internal image processing and is not a
malfunction. This wavering is not recorded and will not affect your images
in any way.
i When the optical zoom is used or when the autofocus is operating, the
image may appear to waver, but this is not a malfunction.
55 English
Select the recording size
The larger the image size (number of pixels), the better the image quality will
be, but the file size will also be larger. Select the image quality that is correct
for the intended purpose.
1
Display the SIMPLE Mode Shooting Menu (page 37), select the
recording size setting, and press the SET button.
To watch on TV
8
TV size
8M [4:3]
EXIT OK
T: The video clip size will be 640 × 480 pixels, and the still image size
will be 3264 × 2448 pixels.
6: The video clip size will be 320 × 240 pixels, and the still image size
will be 640 × 480 pixels.
2
Select the desired video clip recording size, and press the SET
button.
h This completes the recording size setting.
English 56
BEFORE TAKING PICTURES
Select the focus setting
Select the focus range corresponding to the distance between the camera
and the subject.
1
Display the SIMPLE Mode Shooting Menu (page 37), select the focus
setting, and press the SET button.
All ranges
Automatic focus
(people, landscape, etc.)
EXIT OK
7: The camera automatically focuses on the subject within a range of
10 cm (3.94 in.) to infinity (normal).
8: The camera focuses on a subject within a range of 1 cm (0.39 in.) to
80 cm (31.50 in.) (super macro).
2
Select the desired focus range, and press the SET button.
h This completes the focus range setting.
57 English
Hints for taking pictures
Muting the operation sounds
i The audio guidance that sounds when you operate the camera can be
muted (page 132).
Where are the image and audio files saved?
i All the image and sound files are recorded on the card installed in the
camera or in the camera’s internal memory.
Taking pictures in backlight conditions...
i When taking pictures with the light coming from behind the subject, due to
the characteristics of the lens, ghost patterns (flare phenomenon) may
appear in the captured image. In this situation, it is recommended that you
avoid taking pictures with the subject lit from behind.
While the image files are being recorded...
i While the multi-indicator is flashing red, the image files are being written to
the memory, during which time it is not possible to capture another image.
Another image can be captured after the flashing red indicator turns off.
However, even when the multi-indicator is flashing red, depending on the
camera’s internal memory remaining capacity, in some cases the next
image can be captured about 2 seconds after shooting.
English 58
VIDEO CLIP RECORDING
1
Turn on the camera
(page 30), and set it to the
shooting mode (page 35).
[
] button
2
Press the [
h Recording begins.
] button.
h It is not necessary to
keep the [
] button
pressed while shooting.
h When the remaining
recording time available
for the currently recording
clip becomes little, a
countdown of the
remaining recording time
appears on the display.
3
End the recording.
h Press the [
] button
again to stop recording.
Recording time
REC 00:00:09
5
Available recording time
remaining
59 English
SHOOTING SINGLE SHOTS
Capture a still image (single-shot).
1
2
Turn on the camera (page 30),
and set it to the shooting mode
(page 35).
[
] button
Press the [
1 Press the [
halfway.
] button.
] button
h The autofocus operates,
and the image is focused
(focus lock).
2 Continue to gently press
the [
way.
] button all the
h The shutter releases and
the image is captured.
h You can view the captured
image on the monitor by
keeping the [
] button
depressed when you
capture the image.
1
2
F3.5
1/300
Target mark
Shutter speed
Aperture
English 60
SHOOTING SINGLE SHOTS
HINT
Adjusting the monitor brightness
i While the Shooting Screen is active, you can quickly access the screen for
adjusting the brightness of the monitor (page 140) by pressing the MENU
button for at least 1 second.
What is the camera focusing on?
i A target mark & on the monitor
shows the area the camera is
focusing on.
Target mark
i The camera automatically
determines the correct focus by
measuring from 9 different focus
points within the shooting area. If the
target mark is at a position that is
different from the point you wish to
focus on, you can refocus, for
example, by changing the shooting
angle.
F3.5
1/7
Camera shake icon
Shutter speed
i The large target mark appears when
the camera focuses on a wide area
in the center of the screen.
The focus and exposure can be
locked
Aperture
i By assigning an operation shortcut to an arrow button (page 135), you can
set the autofocus or the exposure to a fixed setting. When the exposure
setting is fixed, the Picon appears on the monitor; when the autofocus
setting is fixed, the p icon appears on the monitor.
i When the focus range (page 57) setting is changed, the focus lock is
released.
The shutter speed and aperture are displayed
i In the NORMAL mode, the shutter speed and aperture settings are shown
on the Shooting Screen. You can use them as a reference when shooting.
If the camera shake icon > appears...
i During still image shooting, if the shutter speed is slow and the possibility
that the image may be blurred due to camera shake becomes high, the
camera shake icon may appear on the monitor. In this case, use a tripod to
stabilize the camera when shooting, or set the flash operation mode to
automatic (page 62).
i When shooting with the scene select function set to the fireworks +
mode, the camera shake icon always appears, but this is normal.
61 English
Using the flash
The flash is not only used for photographing under dark conditions, but is also
convenient for example when the subject is in shadow or lit from behind. The
flash is available only when shooting single-shot still images.
1
Display the SIMPLE Mode Shooting Menu (page 37), select the flash
setting, and press the SET button.
h The screen to select the flash operation appears.
Auto
Flash automatically
EXIT OK
9: The camera detects the subject brightness and uses the flash only
when necessary.
:: The flash operates with every image captured regardless of the
conditions.
;: The flash does not operate even in dark situations.
2
3
Select the desired flash operation, and press the SET button.
h This completes the flash operation setting.
Press the [
] button to take the picture.
English 62
SHOOTING SINGLE SHOTS
CAUTION
Do not touch the flash unit when shooting
i The flash unit becomes very hot and may cause a burn. Avoid touching the
flash unit when shooting.
HINT
i The flash works only when shooting single-shot still images.
63 English
SHOOT A STILL IMAGE WHILE
RECORDING A VIDEO CLIP
You can capture a still image (a single-shot) while recording a video clip.
1
Turn on the camera
(page 30), and set it to the
shooting mode (page 35).
[
[
] button
] button
2
3
Press the [
] button.
When you see a scene
you’d like to capture as a
still image. press the
[
] button.
4
Press the [
end the video clip
recording.
] button to
REC 00:00:09
English 64
SHOOT A STILL IMAGE WHILE RECORDING A
VIDEO CLIP
HINT
i When shooting a still image while recording a video clip, the flash does not
operate.
i When the remaining video recording time becomes approximately
50 seconds, it will no longer be possible to capture a still image while
recording a video clip. The exact remaining recording time at which this
occurs will differ depending on the subject and on the video clip mode
setting (page 79). If you intend to capture a still image while recording a
video clip, it is suggested that you take note of the remaining video
recording time.
About the recording size of still images
i The still image shooting size automatically changes to G and the image
is captured.
65 English
MACRO-PHOTOGRAPHY (ZOOM)
Your camera has two zoom functions: optical zoom and digital zoom.
1
2
Point the camera lens at the
subject.
[T] or [W] button
Press the [T/]] or [W/P]
button to compose the desired
image.
[T/]]: Zoom in on the subject.
[W/P]: Zoom out.
h When the zoom switch is
pushed, the zoom bar appears
on the monitor.
h When the optical zoom factor
is at maximum, zooming stops
temporarily. When the [T/]]
button is pressed again, the
mode changes to the digital
zoom mode and zooming
continues.
Monitor
3
Take the picture.
For video clip recording, see
page 59.
Zoom bar
For shooting single shots, see
page 60.
For shooting sequential shots,
see page 81.
When both
optical and digital
zoom are enabled
Optical zoom
Digital zoom (yellow)
When optical
zoom only is
enabled
Pointer
English 66
AFTER USING THE CAMERA IN WATER
After using the camera in water, wash it with fresh water and dry it completely
.
1
2
Turn off the camera, and close the battery/card compartment cover
securely.
Wash the camera with fresh water.
h
Fill a shallow basin with fresh water, and immerse the closed camera for
about 5 minutes. Rotate the monitor unit several times to clean it
completely.
3
Allow the water to drain out through the drainage holes.
Drain the water through the five drainage holes.
h
Monitor unit
Monitor unit
Drainage hole
Drainage hole
Drainage hole
67 English
4
Dry the camera.
h
Use a dry cloth to wipe off any drops adhering to the camera, and leave
it to dry completely in a well-ventilated place away from direct sunlight.
Water may seep out from the drainage holes if the camera is not
completely dry inside. Take special care not to let water get inside the
battery/card compartment.
h
h
Do not use a hair dryer or the like to dry the camera. Exposing the
camera to high temperatures may cause the camera and/or waterproof
seal to become deformed.
English 68
PLAYBACK
SIMPLE/PLAYBACK
PLAYING BACK VIDEO CLIPS AND
STILL IMAGES
1
2
Set the camera to the playback mode (page 35).
Press the [G] or [H] button to display the image you wish to play
back.
h Video clips are indicated by a video clip pattern along the left and right
sides of the screen.
Arrow buttons
SAVE
SET button
PLAY
2008.112.24
<Example: After recording
a video clip>
REC/PLAY
button
2008.112.24
<Example: After capturing
a still image>
3
For a video clip, press the SET button.
h Playback begins.
69 English
To do this...
Do this
Normal forward playback Press the SET button.
Stop playback
Pause
During playback, press the [W] button.
During playback, press the SET button or
press the [T] button.
During accelerated playback, press the [T]
button.
To playback
one image
at a time
(single-
Forward
playback
After pausing playback, press the [H] button.
Reverse
playback
After pausing playback, press the [G] button.
frame step)
Forward
playback
Reverse
playback
After pausing playback, press and hold the
[H] button.
Slow
playback
After pausing playback, press and hold the
[G] button.
During forward playback, press the [H] button.
* The playback speed changes each time the
[H] button is pressed, as follows:
Forward
playback
Normal playback → 2× → 5× → 10× → 15×
Press the [G] button to resume normal
playback speed.
To
accelerate
playback
During forward playback, press the [G] button.
* The playback speed changes each time the
[G] button is pressed, as follows:
15× ← 10× ← 5×
Reverse
playback
Press the [H] button to resume normal
playback speed.
Return to normal playback
speed
Press the SET button.
HINT
If the aappears on the Playback Screen...
i The aicon appears when playing back a file that was saved in segments
(page 83). Although playback of these multiple files is continuous, there is
a slight pause at the point where the files are joined.
English 70
PLAYING BACK VIDEO CLIPS AND STILL IMAGES
How to save one frame from a video clip as a
still image
1
2
Play back the video clip. Pause the playback at the point you wish to
“snap” a photo.
Press the [
] button.
h The currently displayed frame is saved as a still image.
HINT
The size of a video clip file is very large
i Therefore, be aware that if the video clip is uploaded to a computer to be
played back, the computer may not be able to play back the video fast
enough, making it appear jerky. (The video will always be displayed
properly on the monitor or a television.)
i Depending on the card, shooting may end even before the possible
shooting time indicated.
Display the video clip playback point
i During video clip playback, press the MENU button for at least 1 second to
display a bar showing the current playback point in the video clip.
i Press the MENU button for about 1 second to cancel the bar.
CAUTION
During video clip playback, the sound of a motor is audible...
i During recording, the sound of the optical zoom movement or autofocus
movement was recorded. This is not a malfunction.
If no audio is heard...
i The audio is not played back when the video clip is played back in the
frame-by-frame, fast playback or reverse playback mode.
71 English
SLIDESHOW PLAYBACK
You can play back files in succession with the “slideshow playback” feature.
1
Display the SIMPLE Mode
Playback Menu (page 37), select
the slideshow setting, and press
the SET button.
SLIDESHOW
ALL
MOVIE
PHOTO
=
: Play back all files.
3: Play back video clips and
audio files.
START
c: Play back still image files.
2
Select the type of file to play back,
and press the SET button.
h Slideshow playback begins.
h To stop slideshow playback, press
the SET button or MENU button.
HINT
About the slideshow settings
i During slideshow playback, the BGM that was set for the slideshow from
the NORMAL Mode Playback Menu is played. To change the BGM, display
the NORMAL Mode Playback Menu and change the BGM setting for the
“SLIDESHOW” (page 105).
i For slideshows played in the SIMPLE mode, the transition effect is fixed at
“FADE” and the transition interval is fixed at “2 SEC”.
English 72
PLAYBACK VOLUME
Adjust the playback volume for video clips and audio files.
1
Display the SIMPLE Mode
PLAY VOLUME
Playback Menu (page 37), select
the playback volume setting, and
press the SET button.
h The volume control bar appears.
4
VOLUME SETTING
2
Press the [G] or [H] button to set
the volume, and press the SET
button.
h The playback volume is set, and
the display returns to the SIMPLE
Mode Playback Menu.
HINT
In the NORMAL mode
i When you select “PLAY VOLUME” from the NORMAL Mode Playback
Menu and press the SET button, the volume control bar appears.
73 English
DELETING FILES
You can delete files if you no longer need them. You can delete the files one
at a time, or all at once.
1
Display the SIMPLE Mode
Playback Menu (page 37), select
the delete c icon, and press the
SET button.
DELETE SINGLE:
Deletes the currently displayed file.
DELETE ALL:
DELETE
DELETE SINGLE
DELETE ALL
Deletes all files.
OK
2
Select the desired delete mode, and press the SET button.
h The Delete Confirmation Screen appears.
<DELETE SINGLE>
h Press the [G] or [H] button to select the file you wish to delete.
h There is no confirmation screen when deleting single files. Please
make sure that the displayed image is one you wish to delete.
<DELETE ALL>
h Press the [G] or [H] button to confirm the files to delete.
English 74
DELETING FILES
3
Select “DELETE”, and press the SET button.
<DELETE SINGLE>
h The currently displayed file is deleted.
h To delete other files, select the files, select “DELETE” and press the
SET button.
<DELETE ALL>
h The Delete Confirmation Screen again appears. To delete the files,
select “YES”, and press the SET button. When file delete is
completed, “No image” is shown.
HINT
In the NORMAL mode
i When you select “DELETE” from the NORMAL Mode Playback Menu and
press the SET button, the Delete Screen appears.
CAUTION
i Files that are protected from accidental delete cannot be deleted. To delete
protected files, set the protect setting for the files to off (page 107), and
then follow the file delete procedure.
75 English
PLAYBACK MODES
Multi-image display
1
2
3
Display the image you wish to
play back.
Arrow buttons
SET button
Press the [W/P] button.
h The 9-image display appears.
Select the image to play back.
h Press the [G] or [H] buttons to
move the orange frame to the
desired image, and press the
SET button or [T/]] button
to switch to normal (full-
screen) playback of the
selected image.
h If the [W/P] button is
pressed while the 9-image
display is shown, the display
changes to the 20-image
display.
REC/PLAY
button
Orange frame
Still image
Video
clip
100
0001
0004
0007
0002
0005
0008
0003
0006
0009
Audio file
Image number
Folder number
English 76
PLAYBACK MODES
Selecting the playback folder
If the card contains multiple folders, you can select from which folder you
would like to play back.
1
2
Display the Playback Screen.
Press the [W/P] button 3 times.
h The screen to select the playback
folder appears.
100
103
101
104
102
105
h If the [T/]] button is pressed, the
camera changes to the 20-image
display (page 76).
FOLDER : 100SANYO
3
Press the arrow buttons to move the
orange frame to the desired folder,
and press the SET button.
h The files in the selected folder are
displayed in the Playback Screen.
HINT
In the NORMAL mode
i When you select “SELECT FOLDER” from the NORMAL Mode Playback
Menu and press the SET button, the screen to select the playback folder
appears.
77 English
Magnifying (zooming in) the image
Display the image that you want to magnify.
Push the [T/]] button.
1
2
SAVE
106%
h Magnification is enabled.
h The image is magnified, and the
central portion of image is
displayed.
To magnify:
Magnification increases each time
the [T/]] button is pressed.
To return to normal size:
Magnification decreases each time
the [W/P] button is pressed.
h You can press the SET button to
switch to the scan operation. Use the
arrow buttons to see different parts of
the image.
SWITCH
h Press the SET button again to switch
to the magnify/reduce operation.
h Press the MENU button to return to
the normal (100%) view.
HINT
The magnified portion of the image can be saved as a separate image
i Press the [
] button. The magnified portion is saved as a new still
image.
English 78
NORMAL
SHOOTING
NORMAL/SHOOTING
RECORDING SIZE
The image quality of video clips and still images is determined by the
recording size (number of pixels). The larger the recording size, the better the
image quality will be, but the file size will also be larger. Select the recording
size that is correct for the intended purpose.
Movies
The faster the frame rate (frames per second), the smoother playback will be.
However, as with the recording size, the file size is also proportionately larger,
using up more memory. This menu is also used when making audio
recordings.
1
Display the NORMAL Mode Shooting Menu (page 37), select
“MOVIE”, and press the SET button.
(: Record at 640 × 480 pixels, 60 frames per second.
): Record at 640 × 480 pixels, 30 frames per second (high bit rate).
B: Record at 640 × 480 pixels, 30 frames per second (standard bit
rate).
l: Record at 320 × 240 pixels, 30 frames per second.
d: Record at 320 × 240 pixels, 15 frames per second.
<Audio mode>
<: Make an audio recording (voice memo) (page 82).
2
Select the desired recording size, and press the SET button.
h This completes the recording size setting.
CAUTION
When editing video clips (page 112)...
i In order for video clips to be joined, they must have been photographed in
the same mode.
i Video clips that were photographed in different modes cannot be joined.
79 English
Still images
This menu is also used for shooting sequential shots.
1
Display the NORMAL Mode Shooting Menu (page 37), select
“PHOTO”, and press the SET button.
I: Image size is 4000 × 3000 pixels.
U: Image size is 3264 × 2448 pixels (low compression).
V: Image size is 3264 × 2448 pixels (normal compression).
]: Image size is 3264 × 1840 pixels (16:9 ratio).
W: Image size is 1840 × 2448 pixels (portrait orientation).
G: Image size is 1600 × 1200 pixels
[: Image size is 640 × 480 pixels.
R: 3264 × 2448-pixel sequential shots.
t: 1600 × 1200-pixel sequential shots.
2
Select the desired recording size, and press the SET button.
h This completes the recording size setting.
English 80
RECORDING SIZE
Sequential shots
1
Display the NORMAL Mode Shooting Menu (page 37), select
“PHOTO”, and press the SET button.
2
3
Select Ror t, and press the SET button.
Press the [
] button.
h Shooting begins. Shooting continues as long as the [
] button is
kept pressed.
HINT
i The maximum number of images in a sequential shots sequence is about
10.
About the focus when shooting sequential shots
i When sequential shots are captured, the autofocus operates when the
[
] button is pressed halfway, fixing the focus.
Can the flash be used?
i The flash does not operate when shooting sequential shots.
81 English
Audio recording
Your camera can make audio recordings and play them back.
Audio recording
1
2
Display the NORMAL Mode Shooting Menu (page 37), select
“MOVIE”, and press the SET button.
Select <, and press the SET
Remaining time
button.
h The audio recording mode is
enabled.
668
11:44:37
3
Press the [
] button.
Length of recording
h Audio recording begins. During
recording, < appears in the
monitor. It is not necessary to
REC00:00:06
continue pressing the [
button while recording.
]
English 82
RECORDING SIZE
4
End the recording.
h Press the [ ] button again to stop recording.
HINT
You can capture a still image during an audio recording
i Press the [
] button during audio recording to capture a still image.
Note, however, that the resolution in the still image mode automatically
changes to G and the image is captured.
About files saved in segments
i If the continuous recording time of a voice memo exceeds about 13 hours,
of a video clip whose resolution setting is l exceeds about 5 hours
30 minutes, or of a video clip whose resolution setting is d exceeds
about 7 hours, the recorded file is saved once, and the recording continues
in a new file. When recording a video clip whose resolution setting is other
than l or d and the file size exceeds 4 GB, the recorded file is saved
once, and the recording continues in a new file. (These 4 GB segments are
automatically created. The recording session continues until you stop
recording, but video clip or voice memo recording is temporarily interrupted
while the file is being saved.)
Audio playback
1
Display the desired audio file.
00:00:00
PLAY
2008.12.24
83 English
2
Play back the recording.
To do this...
Do this
Press the SET button.
Start
playback
Normal
Pause
Press the SET button.
playback
Press the [T/]] button.
Stop
playback
Press the [W/P] button.
During playback, press the [H] button.
Each time the [H] button is pressed, the
speed increases. If the [G] button is
pressed during fast forward, the speed
decreases.
Fast
forward
During playback, press the [G] button.
Each time the [G] button is pressed, the
speed increases. If the [H] button is
pressed during fast reverse, the speed
decreases.
Fast
Fast
reverse
forward/
fast reverse
Pause
Press the [T/]] button.
Press the SET button.
Return to
normal
playback
CAUTION
If no audio is heard...
i The audio is not played back when the audio recording is played back in
the fast playback or fast reverse mode.
English 84
SCENE SELECT
You can select from various preset settings (aperture, shutter speed, etc.) for
specific shooting conditions.
1
Display the NORMAL Mode Shooting Menu (page 37), select
“SCENE SELECT”, and press the SET button.
Shooting mode setting
Scene
Features
Single-
shot
Sequential
shots
setting
Video clip
=
Auto
The camera makes the
optimum settings.
m
m
m
m
m
Capture a split-second
image of a fast-moving
subject.
a
Sports
m
Enhance the three-
dimensional feel of the
subject by blurring the
background.
>
Portrait
m
m
m
m
m
n
m
m
m
+
For beautiful shots of
Landscape distant scenery.
Photograph the subject
/
Night view
portrait
while keeping the
background night
scenery.
k
Snow &
beach
For photographing bright
scenes, such as on a ski
slope or at the beach.
m
m
m
m
m
m
Photograph subjects
underwater in the sea or
in the pool.
[
Underwater
+
For capturing fireworks at
m
m
n
n
m
m
Fireworks night.
Q
Photograph in low-light
conditions
Lamp
m: Available n: Not available
85 English
2
Select the desired icon, and press the SET button.
h This completes the scene select function setting.
h To return to normal photography, select = from the scene select
menu, and press the SET button.
HINT
i When capturing images using the lamp Q, fireworks + or night view
portrait / setting, use a tripod or other method to stabilize the camera.
i A table showing the limitations for settings corresponding to scene select
icons other than = is on page 182.
English 86
FILTERS
The filter feature changes image characteristics such as color tones, to apply
unique effects to the photographed image.
1
Display the NORMAL Mode Shooting Menu (page 37), select
“FILTER”, and press the SET button.
&: No filter is used (none).
%: Skin tones are enhanced in close-up shots (cosmetic filter).
W: Snap black-and-white photos (monochrome filter).
,: Create a sepia-tone photo (sepia filter).
2
Select the desired icon, and press the SET button.
h This completes the filter setting.
h To return to normal photography, select & from the filter menu, and
press the SET button.
HINT
i A table showing the limitations for settings corresponding to filter icons
other than & is on page 183.
87 English
FLASH OPERATION
The flash is used not only for taking pictures where there is insufficient light,
but also when the subject is in shade or in backlight conditions.
The flash can be enabled only when capturing single still images.
1
Display the NORMAL Mode Shooting Menu (page 37), select
“FLASH”, and press the SET button.
k: The camera detects the subject brightness and uses the flash only
when necessary.
m: The flash operates with every image captured, regardless of the
subject brightness.
l: The flash does not operate even in dark surroundings.
2
3
Select the desired flash operation, and press the SET button.
h This completes the flash operation setting.
Press the [
] button to capture the image.
CAUTION
Do not touch the flash unit when shooting
i The flash unit becomes very hot and may cause a burn. Avoid touching the
flash unit when shooting.
HINT
i The flash works only when shooting single-shot still images.
i By assigning an operation shortcut to an arrow button (page 135), you can
change the flash mode from the Shooting Screen.
English 88
SELF-TIMER
Set the delay time before recording starts after the [
pressed.
] or [
] button is
1
Display the NORMAL Mode Shooting Menu (page 37), select “SELF-
TIMER”, and press the SET button.
N: Turns off the self-timer function.
y: The image is captured about 2 seconds after the [
] button or
] button or
[
] button is pressed.
x: The image is captured about 10 seconds after the [
] button is pressed.
[
2
3
Select the desired icon, and press the SET button.
h This completes the self-timer setting.
Take the picture.
89 English
HINT
i By assigning an operation shortcut to an arrow button (page 135), you can
set the self-timer from the Shooting Screen.
To pause or cancel the self-timer function...
i If the [
released, the self-timer countdown temporarily stops. Press the [
button or [ ] button one more time to restart the self-timer.
] button or [
] button is pressed again before the shutter is
]
i To cancel self-timer photography, select the N icon from the self-timer
menu, and press the SET button.
i The self-timer is automatically reset to off N after the power save mode
is activated and the camera turned off.
When x is selected...
i When the [
] button or [
] button is
pressed, the multi-indicator will blink for
about 10 seconds, and then the image
is captured. Also, 4 seconds before the
shutter releases, the indication shown in
the illustration appears on the monitor.
If you swivel the monitor unit
to its farthest position, the
image on the monitor will be
inverted.
English 90
MOTION COMPENSATION (IMAGE
STABILIZER)
Your camera can minimize a jittery picture by compensating for unintentional
hand motion.
Compensate for camera shake during video
clip recording
1
Display the NORMAL Mode Shooting Menu (page 37), select “MOVIE
STABILIZER”, and press the SET button.
p: Compensate for unintentional camera motion during video clip
recording. The field of view (see page 93) does not change when
the [
] button is pressed, so this setting is convenient when
shooting mostly video clips (video clip field of view display).
q: Compensate for unintentional camera motion during video clip
recording. The field of view does not change when the [
is pressed, so this setting is convenient when shooting mostly still
images (still image field of view display).
] button
]: Disengages the motion compensation function (OFF).
2
Select the desired setting, and press the SET button.
h This completes the movie stabilizer setting.
Compensate for camera shake during still
image shooting
1
Display the NORMAL Mode Shooting Menu (page 37), select
“PHOTO STABILIZER” and press the SET button.
\: Motion compensation is enabled.
]: Motion compensation is not enabled.
2
Select the desired setting, and press the SET button.
h This completes the photo stabilizer setting.
91 English
HINT
If the motion compensation does not seem to be working...
i Due to the mechanical characteristics of this function, it may not be
possible for the camera to compensate for violent motion.
i If the digital zoom (page 66) is being used, the large magnification factor
may make it difficult for the motion compensation function to work correctly.
i When using a tripod or other means to stabilize the camera during
shooting, please turn the motion compensation function off ]. If the
motion compensation function is enabled when it is not actually needed, it
may result in an image that appears unnatural.
When motion compensation is enabled,
i The following icons are shown on the monitor:
Movie stabilizer
TV-SHQ
Setting Movie stabilizer Photo stabilizer
+
00:04:30
Photo stabilizer
Movie field of
view display
Icon
display
Photo field of
view display
Can’t set the photo stabilizer setting?
i The photo stabilizer is automatically turned off after any of the following
operations:
h Setting the flash mode to forced flash
h Setting the shooting mode to the sequential shots mode
h Setting flicker reduction (page 139) to “ON”
h Setting the scene select function to the night view portrait, fireworks, or
lamp mode
The photo stabilizer isn’t working?
i The photo stabilizer does not work when you are capturing a still image
while recording a video clip.
i The photo stabilizer does not work when the ISO sensitivity is set to -.
Limitations when the photo stabilizer is “ON”
i The time it takes for the camera to save an image may be slightly longer
when the photo stabilizer is set to “ON”.
English 92
MOTION COMPENSATION (IMAGE STABILIZER)
<Concerning the changing field of view when motion compensation is
enabled>
i When the motion compensation is set to “ON”, the field of view during
recording standby differs from the recordable field of view as shown below.
i When set to the motion compensation q setting, the video clip recording
range is as shown in the recording standby screen.
During still image
shooting
Display during
recording standby
During video clip
recording
For p setting
For q setting
Video clip
recording area
For ] setting
i When the still image shooting resolution is set to [ and the scene select
function to =, a, >, + or k (page 85), a still image captured
during video clip recording will have the same field of view as the video
clip.
93 English
FOCUS RANGE
1
Display the NORMAL Mode Shooting Menu (page 37), select
“FOCUS”, and press the SET button.
h When shooting a subject at a medium to far distance, by setting the
focus range to *, you will find it both easier and faster to focus.
-: Wide end: 10 cm (3.94 in.) to infinity
Tele end: 80 cm (31.50 in.) to infinity (total range mode)
*: 80 cm (31.50 in.) to infinity (normal mode)
-: The focus can be manually set to any distance from 1 cm
(0.39 in.) to 8 m (26.25 ft.), as well as to infinity (manual focus).
+: 1 cm (0.39 in.) to 80 cm (31.50 in.) (super macro mode: wide
end only)
h When the focus range is set to *, + or -, the corresponding
indication appears on the monitor.
2
Select the desired icon, and press the SET button.
h This completes the focus range setting.
HINT
i When the focus range is set to super macro +, the zoom is temporarily
set to the wide end.
i By assigning an operation shortcut to an arrow button (page 135), you can
change the focus range setting from the Shooting Screen.
English 94
FOCUS RANGE
How to use the manual focus
1
2
Display the NORMAL Mode Shooting Menu (page 37), select
“FOCUS”, and press the SET button.
Select -, and press the SET
button.
TV-SHQ
362
00:05:07
h The focus distance adjustment
bar appears.
3
Press the [G] or [H] button to
adjust the focus distance, and
press the SET button.
2.0m
h The focus distance is set, and
you are returned to the Shooting
Screen.
HINT
About the focus distance
i The focus distance indication shows the distance between the center of
the lens and the subject.
i In some cases there may be a slight variance between the distance
(numerical figure) you set in the manual focus mode and the actual
distance.
About zoom movement when using the manual focus
i If the focus distance is set to 70 cm (27.56 in.) or less, the zoom changes
to the largest setting that is suitable for that focus distance.
i When the focus distance is set to 70 cm (27.56 in.) or less, the zoom will
function only within the range at which the image is focused.
95 English
FOCUS MODE
You can choose from the following 2 types of autofocus (still image shooting
only):
9-point range finder focus:
The correct focus is determined from 9 different focus points within the
shooting area visible on the monitor. When the image is focused, a target
mark & appears.
Spot focus:
The camera focuses on the subject in the center of the monitor.
1
2
Display the NORMAL Mode Shooting Menu (page 37), select
“FOCUS MODE”, and press the SET button.
B: 9-point range finder focus is selected.
C: Spot focus is selected.
Select the desired icon, and
TV-SHQ
press the SET button.
h The focus mode is set.
h When the spot focus setting is
selected, the focus mark +
appears in the center of the
monitor.
40
00:02:47
Focus mark
English 96
LIGHT-MEASURING MODE SETTING
You can select from 3 types of light-measuring modes.
Multi-section light-measuring:
The light is modulated after sampling from multiple areas of the entire
shooting screen.
Center-weighted light-measuring:
The light is modulated for the entire image after measuring from mostly the
center area.
Spot light-measuring:
You can compose the picture and capture the image after first modulating the
light only at the center spot of the monitor.
1
2
Display the NORMAL Mode Shooting Menu (page 37), select “EXP
MEASURE”, and press the SET button.
n: Multi-section light-measuring
W: Center-weighted light-measuring
Y: Spot light-measuring
Select the desired light-
measuring mode, and press the
SET button.
TV-SHQ
40
00:02:47
h This completes the light-
measuring mode setting.
h When spot light-measuring is
selected, the light-measuring
spot mark
appears in the
center of the monitor.
Light-measuring spot mark
97 English
ISO SENSITIVITY
With the initial settings, the ISO sensitivity is automatically set according to
the brightness of the subject. However, the ISO sensitivity can be set to a
fixed setting.
1
Display the NORMAL Mode Shooting Menu (page 37), select “ISO”,
and press the SET button.
=: The ISO sensitivity is set automatically (video clip recording: ISO
equivalent to ISO 50 to 1600; still image shooting: ISO 50 to 400).
*: Sets sensitivity to ISO 50 (video clip high sensitivity recording:
ISO 100).
u: Sets sensitivity to ISO 100 (video clip high sensitivity recording:
ISO 200).
v: Sets sensitivity to ISO 200 (video clip high sensitivity recording:
ISO 400).
w: Sets sensitivity to ISO 400 (video clip high sensitivity recording:
ISO 800).
6: Sets sensitivity to ISO 800 (video clip high sensitivity recording:
ISO 1600).
-: Sets sensitivity to ISO 1600 (video clip high sensitivity recording:
ISO 3200).
* The indicated ISO value is the standard output sensitivity.
2
Select the desired icon, and press the SET button.
h This completes the ISO sensitivity setting.
HINT
i By setting a higher ISO sensitivity, you can set faster shutter speeds and
capture images in darker locations, but noise in the captured images may
increase or the images may be irregular.
i By assigning an operation shortcut to an arrow button (page 135), you can
change the ISO setting from the Shooting Screen.
CAUTION
Does the image appear to flicker when recording a video clip?
i If recording a video clip under fluorescent lights with the ISO sensitivity set
to w or higher, a noticeable flicker may appear in the image.
English 98
WHITE BALANCE
This camera automatically adjusts the white balance under most lighting
conditions. However, if you want to specify the lighting conditions or change
the overall tone of the image, the white balance can be manually set.
1
Display the NORMAL Mode Shooting Menu (page 37), select “WHITE
BALANCE”, and press the SET button.
>: The camera will make the white balance adjustment automatically
based on the natural and artificial light conditions.
r: For shooting outside on a sunny day.
o: For shooting outside on a cloudy day.
p: For shooting inside under fluorescent lighting.
q: For shooting inside under incandescent lighting.
^: This setting is used for a more accurate white balance using the
existing light source (one push). Please use it when the light source
cannot be identified, for example.
Setting procedure
1 Select the ^ icon.
2 Fill the entire screen with a plain white card (or piece of
paper, etc.), and press the SET button.
h This completes the white balance setting.
2
Select the desired icon, and press the SET button.
h This completes the white balance setting.
HINT
To cancel the white balance setting
i Perform step 1, select >, and then press the SET button.
99 English
FACE CHASER
The face chaser detects the subject’s face, and adjusts the brightness and
focus in a way that produces a clear and bright photo of the subject’s face.
1
2
Display the NORMAL Mode Shooting Menu (page 37), select “FACE
CHASER”, and press the SET button.
-: The face chaser function is enabled.
.: The face chaser function is not enabled.
Select the desired setting, and press the SET button.
h This completes the face chaser setting.
HINT
When the face chaser is set to “ON”...
i Each face in the Shooting Screen is marked with a green frame.
i Faces that are in focus are marked with a double green frame.
i If you press the [
] button halfway, the frames marking the faces that
are in focus change to orange.
If you magnify an image that was captured with the face chaser function
enabled, the magnified image will center on the face(s).
i The scene select function setting automatically changes to =.
CAUTION
i The face chaser function does not work while the digital zoom is being
used.
i The face chaser function does not work when zooming in or out.
i The face chaser function may not work when the subject’s face in the
monitor is relatively small or appears dark.
English 100
HIGH SENSITIVITY MODE
When you shoot in the high sensitivity mode, the captured image appears
even brighter than that specified by the ISO sensitivity and exposure
compensation settings.
1
2
Display the NORMAL Mode Shooting Menu (page 37), select “HIGH
SENSITIVITY”, and press the SET button.
1: The high sensitivity mode is activated.
2: The high sensitivity mode is not activated.
Select the desired setting, and press the SET button.
h This completes the high sensitivity mode setting.
CAUTION
Limitations of the high sensitivity mode
i If the flicker reduction function (page 139) is set to “ON”, the high
sensitivity mode automatically changes to “OFF”.
i When the shutter speed is reduced to create a bright image, video clip
motion will appear uneven during playback.
i When shooting in a dark environment, the autofocus and auto exposure
may not function effectively.
101 English
DIGITAL ZOOM SETTING
This setting allows you to specify whether or not the digital zoom is enabled
during zoom shooting.
1
2
Display the NORMAL Mode Shooting Menu (page 37), select
“DIGITAL ZOOM”, and press the SET button.
Q: Digital zoom can be used.
B: Digital zoom cannot be used.
Select the desired setting, and press the SET button.
h This completes the digital zoom setting.
HINT
i The digital zoom does not function in the following situation:
When the still image mode is set to I.
English 102
SPECIFY A FOLDER TO SAVE
FILES
Create or select a recording folder (a folder in which to store recorded files).
1
Display the NORMAL Mode
Shooting Menu (page 37), select
“REC FOLDER” and press the
SET button.
REC FOLDER
NEW
100
<Create a new folder>
h Select “NEW”.
<Select an existing folder>
h Select the desired folder number.
OK
2
Press the SET button.
h This completes the create/select folder setting.
h If you created a new folder, it automatically becomes the selected
recording folder.
CAUTION
When an existing folder cannot be selected or a new one created...
i A folder cannot be selected if it was created using a different device, or if it
already contains the maximum number of files.
103 English
EXPOSURE COMPENSATION
By assigning the exposure compensation operation shortcut to an arrow
button (page 135), you can make the image lighter or darker when capturing
images.
1
2
Assign the operation
shortcut to an arrow button
(page 135).
[G] or [H] button
Press the arrow button to
which the operation
shortcut was assigned.
h
The exposure
compensation bar
appears.
3
Press the [G] or [H] button
to adjust the exposure.
h
The exposure
compensation numerical
value is shown at the left
end of the exposure
compensation bar.
The exposure
compensation can be set
to a value from –1.8 EV to
+1.8 EV.
TV-SHQ
h
h
668
01:17:32
The exposure
compensation bar is
canceled when the MENU
button or the SET button is
pressed.
Pointer
Exposure compensation bar
HINT
The exposure compensation setting is canceled in the following cases:
i
i
i
i
When the pointer is set to the center position.
When the camera is set to the playback mode.
When the standby mode is activated.
After the power is turned off.
English 104
PLAYBACK
NORMAL/PLAYBACK
SLIDESHOW PLAYBACK
Specify the settings for playing back files continuously in a “slideshow” format.
In a slideshow of still images, you can set the transition time, transition effects
and BGM.
1
Display the NORMAL Mode
Playback Menu (page 37), select
“SLIDESHOW”, and press the
SET button.
SLIDESHOW
MODE
TIME
ALL
1sec
MODE:
EFFECT
BGM
Specify the file type to play back.
ALL:
Play back all files.
OFF
START
OK
MOVIE:
Play back video clips and audio
files.
PHOTO:
Play back still image files.
TIME:
Adjust the transition speed (the
period that an image is displayed
before it changes to the next image).
EFFECT:
Select a transition effect as an image
changes to the next image.
BGM:
Specify the settings for playing
background music during slideshow
playback.
START:
Begin slideshow playback.
<Changing a setting>
1 Select the item you wish to change, and press the SET button.
2 Press the [T/]] or [W/P] button to change the setting.
3 Press the SET button.
105 English
2
Select “START” and press the SET button.
h Slideshow playback begins.
h To stop slideshow playback, press the SET button or MENU button.
HINT
BGM for video clips?
i When video clips are played back in a slideshow, the recorded audio track
is played back; the BGM is not played.
Did you delete a BGM audio file from the camera?
i The three BGM audio files that were stored in your camera’s internal
memory at the time of purchase can be recovered by formatting the
internal memory.
English 106
FILE PROTECT
Prevent accidental erasure of image and audio files.
1
2
Display the file that you want to protect from accidental erasure, and
display the NORMAL Mode Playback Menu (page 37).
Select “PROTECT” and press the
PROTECT
SET button.
h “LOCK” appears.
h If the protect mode has already
been enabled for the file, then
“UNLOCK” appears.
LOCK
EXIT
OK
3
Select “LOCK”, and press the
SET button.
h The protect mode is set for the
file.
h The protect mark B indicates
that the file is locked.
CAUTION
i Even if the protect mode is set for certain files, they will be deleted if the
card is reformatted (page 148).
HINT
To select a different image in steps 2 and 3...
i Press the [G] or [H] button.
To cancel the protect mode for a file...
i Display the desired file and repeat steps 1 to 3. The protect mark B will
disappear and the protect mode is canceled.
107 English
ROTATE STILL IMAGE
Captured still images can be rotated to the correct orientation for viewing.
1
2
Display the still image you wish to rotate, and display the NORMAL
Mode Playback Menu (page 37).
Select “ROTATE”, and press the
ROTATE
SET button.
RIGHT:
Rotates image clockwise
90 degrees.
LEFT:
RIGHT
LEFT
Rotates image counterclockwise
90 degrees.
OK
3
Select “RIGHT” or “LEFT”, and press the SET button.
h Each time the SET button is pressed, the image is rotated another 90
degrees.
HINT
i An image for which the protect mode has been enabled cannot be rotated.
To rotate a protected image, cancel the protect mode before beginning the
rotate image procedure (page 107).
English 108
REDUCE STILL IMAGE SIZE
(RESIZE)
A captured image can be resized to a smaller size and saved as a separate
image.
1
2
Display the still image whose size you want to change, and display
the NORMAL Mode Playback Menu (page 37).
Select “RESIZE”, and press the
RESIZE
SET button.
(3264×2448)
<For still images with a 4:3
vertical-to-horizontal aspect ratio>
2M (1600×1200)
0.3M (640×480)
2M:
The size changes to
1600 × 1200 pixels.
OK
0.3M:
The size changes to
640 × 480 pixels.
<For still images with a 16:9
aspect ratio>
2M:
The size changes to
1920 × 1080 pixels.
0.9M:
The size changes to
1280 × 720 pixels.
3
Select the new image size, and press the SET button.
h Resizing begins.
HINT
Why can’t the image be resized?
i An image can be resized only to a smaller (or the same) size, not to a
larger size.
109 English
CORRECTING THE RED-EYE
EFFECT AND IMAGE BLUR
Repair the red-eye effect in still images to make the eyes appear more
natural, and enhance the contrast of blurry images.
1
2
Display the image to be modified, and display the NORMAL Mode
Playback Menu (page 37).
Select “EDIT PHOTO”, and press the
EDIT PHOTO
SET button.
h The Edit Photo Screen appears.
RED-EYE CORRECT.:
RED-EYE CORRECT.
Repair the red-eye effect.
CONTRAST CORRECT:
CONTRAST CORRECT
Enhance the image contrast.
OK
3
4
Select the desired type of edit, and
press the SET button.
h The corresponding edit screen
appears.
RED-EYE CORRECT.
CORRECTION:
Proceed with the image correction.
EXIT:
Return to the Edit Photo Screen.
CORRECTION
EXIT
OK
<Example: Red-eye
correction>
Select “CORRECTION”, and press
the SET button.
RED-EYE CORRECT.
h Image editing begins. During
image processing, “Processing” is
shown on the screen.
h When editing is completed, the
modified image is shown. Check
the image to see if the post-
processing result is satisfactory.
NEXT
<Example: Red-eye
correction>
English 110
CORRECTING THE RED-EYE EFFECT AND IMAGE
BLUR
5
Press the SET button.
h A screen appears for you to specify
whether or not to save the original
image.
RED-EYE CORRECT.
SAVE AS NEW
OVERWRITE
SAVE AS NEW:
The corrected image is saved as a
separate image, and the original image
is preserved.
OK
OVERWRITE:
The original file is deleted, and only
the corrected image is saved.
6
Select the desired method to save the corrected image, and press
the SET button.
h The corrected image is saved, and you are returned to the Edit Photo
Screen.
HINT
If the “Red-eye correction not successful” message appears...
i The camera was not able to successfully repair the image.
i
The correction function works to automatically edit flaws that the camera
detects in captured images. In some cases, the camera may fail to correct a
flaw.
Concerning the date and time information for the saved image
i
When an image is corrected and saved, the recorded date and time of
capture (Exif information) remains unchanged from the original image.
However, the file date shown on the computer changes to the date and time
the image was revised.
111 English
EDITING VIDEO CLIPS
You can trim away unwanted portions from a video clip and save it as a new
video clip (video clip cutting [extracting]). You can also join video clips
together and save them as one separate clip (“joining”).
Procedure to cut (extract) a portion of a video clip
1
2
Specify the frames
(1, 2) where the
video clip is to be
cut.
A
B
C
J
Extract the specified portion.
[Two ways to cut the
video clip]
i Trim away portions
A and C, and save
portion B.
i Delete portion B,
and join portions A
and C.
i The original
video clip is
not affected.
(You can also choose to erase the original video clip when the new clip is
saved.)
English 112
EDITING VIDEO CLIPS
Procedure to join video clips
Specify the video clip that will come first.
J
Specify the video clip that you wish to
append (join).
J
Join the video clips.
i The video clips are joined.
i
The original video clips are not affected.
(You can also choose to erase the
original video clips when the new clip is
saved.)
CAUTION
Caution when editing video clips
i When editing video clips, do not press the REC/PLAY button. If you press
the REC/PLAY button while editing video clips, not only will the editing not
be properly completed, but the original video clip may also be erased.
i As the number or size of the video clips increases, the card memory may
become full, making it impossible to edit the video clips. In this case, you
will need to free some of the memory on the card, either by deleting files
that are no longer necessary (page 74), or by selecting “OVERWRITE”
when saving edited video clips (pages 116 and 118).
113 English
Video clip cutting (extracting)
Display the video clip from which you wish to extract a segment.
Display the NORMAL Mode
1
2
EDIT VIDEO
Playback Menu (page 37), select
“EDIT VIDEO”, and press the SET
button.
CUT
JOIN
OK
3
Select “CUT” and press the SET
button.
h The Cutting Screen appears.
Start point
CUT
00:00:10
SAVE
English 114
EDITING VIDEO CLIPS
4
Specify the start point of the extract.
h Use the procedure below to specify the frame from which the video
clip extract will start.
h Play the video clip until approximately the desired point, pause the
video clip, then play the video clip one frame at a time, stopping at the
start point of the extract. This will be the first frame of the extract.
h If the start point of the video clip is also the start point of the extract,
proceed to step 5.
<Procedure>
Play:
After pausing playback, press and hold the [H] button for about
2 seconds for forward playback, or the [G] button for reverse
playback.
Pause:
During playback, press the SET button.
Accelerated playback:
During playback, press the [G] or [H] button to change the playback
speed.
Single frame:
After pausing playback, press the [H] button to move forward one
frame, or the [G] button to move back one frame.
5
Press the [T/]] button.
Approximate playback time
h The start point of the video clip
extract is set, and the screen to
CUT
00:00:06
specify the end point appears.
h Specify the end point of the
extract by following the same
procedure as in step 4.
<When joining the first and latter
portions>
1 Press the [W/P] button.
h Each time the [W/P] button
is pressed, the sections to
delete and the sections to
save are reversed.
SAVE
End point
Portion to be deleted
2 Specify the end point of the
extract. The frame following the
end point of the extract will be
the start point of the latter
portion to be joined.
115 English
6
Press the [R] button.
h A screen appears for you to select
either to save the edited video clip
as a new (separate) file, or to
delete the original video clip and
replace it with the edited video
clip.
CUT
SAVE AS NEW
OVERWRITE
REVIEW CLIP
SAVE AS NEW:
OK
The edited video clip will be saved
as a new file. The original video
clip remains unchanged.
OVERWRITE:
The original video clip will be
deleted. Only the edited video clip
will be saved.
REVIEW CLIP:
Play back the edited video clip
before saving it.
7
Select the desired option, and press the SET button.
h Editing starts.
h When editing ends, you are returned to the NORMAL Mode Playback
Menu.
HINT
i If the original video clip is protected, even if you select “OVERWRITE” in
step 7 and press the SET button, the original video clip will not be erased.
If you want it to be erased, you will need to first remove the protection
(page 107).
i If the “Card full” message appears, you will need to free some of the
memory by deleting files that you do not need to keep.
CAUTION
Warning concerning the battery pack remaining charge
i During the editing of lengthy video clips, the time to process the large
amount of data can become quite long. To avoid problems caused by the
battery pack becoming depleted in the middle of video clip editing, before
starting to edit be sure that a sufficiently charged battery pack is installed
in the camera, or connect an AC adaptor (sold separately).
i It is recommended that a computer be used to edit long video clips.
English 116
EDITING VIDEO CLIPS
Joining video clips
CAUTION
i Video clips that were photographed in different modes cannot be joined.
1
2
Display the NORMAL Mode
Playback Menu (page 37), select
“EDIT VIDEO”, and press the SET
button.
EDIT VIDEO
CUT
JOIN
OK
Select “JOIN” and press the SET
button.
h The 6-image playback display for
video clips appears.
Select a clip
SAVE
100
0001
0004
0002
0005
0003
0006
117 English
3
4
Move the orange frame to the video
clip you wish to join, and press the
SET button.
h The specified video clip is labeled
with a number.
h Up to 9 video clips can be
selected.
h To cancel a selection and remove
the number label from a video
clip, select the video clip and
press the SET button.
Select a clip
SAVE
00:00:30
100
0001
0004
0002
0005
0003
0006
Press the [R] button.
h A screen appears for you to select
either to save the joined video clip
as a new (separate) file, or to
delete the original video clips and
replace them with the joined video
clip.
JOIN
SAVE AS NEW
OVERWRITE
REVIEW CLIP
SAVE AS NEW:
OK
The joined video clip will be saved as
a new file. The original video clips
remain unchanged.
OVERWRITE:
The original video clips will be
deleted. Only the joined video clip
will be saved.
REVIEW CLIP:
Play back the joined video clip
before saving it.
English 118
EDITING VIDEO CLIPS
5
Select the desired option, and press the SET button.
h Editing starts.
h When editing ends, you are returned to the NORMAL Mode Playback
Menu.
HINT
i If the file size of the video clip after editing exceeds 4 GB, it is not possible
to either “SAVE AS NEW” or “OVERWRITE”.
CAUTION
Warning concerning the battery pack remaining charge
i During the editing of lengthy video clips, the time to process the large
amount of data can become quite long. To avoid problems caused by the
battery pack becoming depleted in the middle of video clip editing, before
starting to edit be sure that a sufficiently charged battery pack is installed
in the camera, or connect an AC adaptor (sold separately).
i It is recommended that a computer be used to edit long video clips.
119 English
PRINTING INSTRUCTIONS
In addition to using your printer to print out still images captured with your
camera, as with conventional film, you can have prints made at shops offering
digital print services. Moreover, this camera is DPOF-compatible, so you can
use the camera to specify the number of prints, whether or not the date is
displayed on the print, and also to request an index print.
Display the Printing Instructions Screen
1
Display the NORMAL Mode
Playback Menu (page 37), select
“PRINT INSTRUCTIONS”, and press
the SET button.
PRINT INSTRUCTIONS
ALL IMAGES
EACH IMAGE
INDEX
ALL IMAGES:
The specified printing instructions
apply to all the images.
EACH IMAGE:
ALL CLEAR
OK
The printing instructions are
specified for each individual image.
INDEX:
All the still images are printed as
miniature images (thumbnail
images), several images on one
print.
ALL CLEAR:
Clear all the printing instructions.
This cannot be selected if no printing
instructions have been specified for
the image.
English 120
PRINTING INSTRUCTIONS
HINT
Printing a single frame from a video clip
i To print with a printer or have the digital print service shop print out a still
image from a video clip, you must first save it (extract still) as a still image
(page 71).
About the DPOF format
i DPOF (Digital Print Order Format) is a print order format. You can connect
your camera to a DPOF-compatible printer to produce your prints. You can
also set the printing instructions for the desired images, and then have the
requested images printed automatically (page 162).
About the finished prints
i Rotated images (page 108) will be printed in their original orientation.
i The quality of the print output will differ depending on the print service and
printer used.
121 English
Specifying date imprinting and print quantities
You can specify printing instructions for each individual image (EACH
IMAGE), or apply the printing instructions to all the images (ALL
IMAGES).
1
2
Display the Printing Instructions Screen (page 120).
Select “ALL IMAGES” or “EACH
IMAGE”.
ALL IMAGES:
The printing instructions are applied to
all the images.
PRINT INSTRUCTIONS
ALL IMAGES
EACH IMAGE
INDEX
EACH IMAGE:
ALL CLEAR
OK
The printing instructions are applied
only to the image currently displayed.
3
Press the SET button.
h The Date/Copies Print Screen
appears.
ALL IMAGES
:
:
----/--/--
copy
0
h If “EACH IMAGE” was selected,
press the [G] or [H] button to
display the desired image to print.
h The printing instructions that are
currently active for the displayed
image are shown. You can press
the [G] or [H] button to confirm the
printing instructions for each image.
COPIES 1
OK
Printing instructions
ALL IMAGES
:
:
2008/12/24
2 copies
COPIES 2
OK
<Completed printing
instructions>
English 122
PRINTING INSTRUCTIONS
4
Specify whether the date is
displayed on the print, and the
number of prints.
Dated prints
Quantity
<Specify the number of prints>
h Press the [T/]] or [W/P]
button.
ALL IMAGES
2008/12/24
1 copy
:
:
h The quantity indication changes.
h Display the desired number of
prints.
COPIES 1
EXIT OK
h Press the SET button.
h The number of prints is set.
<Specify dated prints>
h From the screen on which the
number of prints is set, press the
MENU button.
Specify date imprint?
h The screen to confirm dated
prints appears.
YES: Print the date on the
photo.
YES
NO
NO: Do not print the date.
h Press the [T/]] or [W/P] button
to indicate your selection.
OK
5
Press the SET button.
h The printing instructions for the requested print quantities and dated
prints are stored.
123 English
Index print
Printing out many small images on one sheet is called an “index print”.
This is convenient for use as a list of the images you have captured.
1
2
3
Display the Printing Instructions Screen (page 120).
Select “INDEX”.
Press the SET button.
INDEX PRINT
h The Index Print Screen appears.
SET:
Specify an index print copy.
EXIT:
Discontinue the setting procedure,
and return to the Printing
Instructions Screen.
SET
EXIT
OK
4
Select “SET”, and press the SET
button.
h This completes the setting for the
index print. You are returned to
the Printing Instructions Screen.
HINT
To cancel the index print setting
i Follow steps 1 and 2, select “CLEAR” in step 3, and press the SET button.
English 124
PRINTING INSTRUCTIONS
Clearing all the printing instructions
Delete the printing instructions for all images.
1
2
3
Display the Printing Instructions Screen (page 120).
Select “ALL CLEAR”.
Press the SET button.
h The Confirm All Clear Screen
ALL CLEAR
:
:
2008/12/24
copies
appears.
CANCEL:
2
Clear the printing instructions for all
images.
EXIT:
CANCEL
EXIT
Cancel the clear procedure and
return to the Printing Instructions
Screen.
OK
4
Select “CANCEL”, and press the SET
button.
h All the printing instructions are
cleared and you are returned to the
Printing Instructions Screen.
125 English
COPY FILES
Images and audio files recorded in the camera’s internal memory can be
copied to the card, and likewise from the card to the internal memory.
1
2
3
Insert the card in the camera (page 28).
Display the NORMAL Mode Playback Menu (page 37).
Select “COPY”, and press the SET
COPY
button.
h The screen to copy files appears.
INT MEM
CARD
INT MEM
CARD
4
Select the copy direction.
INT MEM CARD:
Copy files from the internal memory to
the card.
OK
CARD
INT MEM:
Copy files from the card to the internal
memory.
* If no card is set in the camera, you
cannot copy files.
English 126
COPY FILES
5
Press the SET button.
h The screen to select the type of
copy appears.
INT MEM
CARD
h The copy source image is shown in
the background on the screen.
COPY SINGLE:
COPY SINGLE
COPY ALL
Copy one file.
COPY ALL:
OK
Copy all the files from the copy source
to the copy destination.
6
7
Select the desired type of copy.
<When selecting “COPY SINGLE”>
1 Press the [G] or [H] button to display the file you wish to copy.
2 Press the [T/]] or [W/P] button to select “COPY SINGLE”.
<When selecting “COPY ALL”>
1 Press the [T/]] or [W/P] button to select “COPY ALL”.
Press the SET button.
h The files are copied.
127 English
DISPLAYING FILE PROPERTIES
(INFORMATION SCREEN)
On the Information Screen you can check what the settings were when a file
was recorded with your camera.
1
2
Display the desired file on the camera monitor.
Press the MENU button for at
least 1 second.
h The Information Screen
appears.
2
3
4
5
TV-SHQINFO
100-0001
1
640×480 30fps SHQ 11.9MB
MPEG-4 AVC/H.264
+0.3
00:00:15
h If the MENU button is
pressed again, the
Information Screen is
canceled.
1 Video clip mode settings
2 Image or sound number
3 Protect setting
4 File size
5 Shooting or recording
time
6 Exposure compensation
setting
7 Aperture value
8 Shutter speed
9 Remaining battery charge
0 Date and time of image
A Still image resolution
settings
6
9
@
2008.12.25 19:30
<Video clip file>
2
3
4
7
8
6
B
9
INFO
100-0002
2.2MB
A
@
3264×2448
F6.8
1/1000
+0.3
50
ISO
2008.12.25 19:30
<Still image file>
B ISO sensitivity setting
2
3
4
5
INFO
100-0003
987KB
00:00:03
AAC
9
;
2008.12.25 19:30
<Audio file>
English 128
OPTION SETTINGS
OPTION SETTINGS
DISPLAY THE OPTION SETTING
MENU
The camera settings are executed via the Option Setting Menu.
1
2
Set the operating mode to the
NORMAL mode (page 36).
1
2
3
1
2
3
Press the MENU button to display
the Menu Screen.
Switch to
simple menu
S
N
EXIT OK
Option tab
3
Select an Option tab (1, 2 or 3), and
press the SET button.
h The Option Setting Menu appears.
OPTION MENU1
CLOCK SET
1
2
3
1
2
3
N
INFO DISPLAY
STARTUP DISPLAY
OPERATION BEEP
POST VIEW
SHORTCUTS
EXIT OK
S
To access a Setting Screen
4
Press the [T/]] or [W/P] button
to select the item you wish to set,
and press the SET button.
h The Setting Screen for the selected
item appears.
h To return to the Menu Screen, press
the MENU button.
INFO DISPLAY
SHOW ALL
DATE & TIME
COUNTER
OFF
OK
129 English
SCREEN DISPLAY
Specify what information is displayed on the Playback Screen.
1
2
Display the Option Setting Menu [E1] (page 129).
Select “INFO DISPLAY”, and press
INFO DISPLAY
the SET button.
SHOW ALL
DATE & TIME
COUNTER
OFF
SHOW ALL:
Display the capture date and
playback time (for video clips).
DATE & TIME:
Display the capture date.
COUNTER:
OK
Display the video clip playback time.
OFF:
Do not display the capture date and
playback time.
3
Select the desired setting, and press the SET button.
h This completes the screen display setting.
English 130
SELECT THE STARTUP DISPLAY
The startup display is the display that appears on the monitor when the
camera is turned on in the recording mode.
1
2
Display the Option Setting Menu [E1] (page 129).
Select “STARTUP DISPLAY”, and
press the SET button.
DATE & TIME:
The camera’s date and time setting
is shown.
Xacti:
STARTUP DISPLAY
DATE & TIME
Xacti
INDEX
OFF
The Xacti logo is shown.
INDEX:
OK
An animated character (penguin) is
shown.
OFF:
No startup display.
3
Select the desired setting, and press the SET button.
h The selected startup display is set.
131 English
OPERATION SOUNDS
Use this menu to set the confirming audio signals when the camera is turned
on/off or when the operation buttons ([
] button, SET button, MENU
button, etc.) are pressed, to adjust the operation sound volume, and to
enable/disable the audio guide.
1
2
Display the Option Setting Menu [E1] (page 129).
Select “OPERATION BEEP”, and
press the SET button.
OPERATION BEEP
TURN ON/OFF
SHUTTER
KEY SW
ON
D
h If “ALL OFF” is selected and the
SET button pressed, all the
operation sounds are muted.
h If the MENU button is pressed, you
are returned to the Option Screen.
TURN ON/OFF:
A
AUDIO GUIDE
OPERATION VOL
ALL OFF
ON
4
OK
Mute or enable the sound that is
produced when the power is turned
on or off.
SHUTTER:
Select the sound that is produced
when the [
] button is pressed, or
when a photo is taken using the self-
timer.
KEY SW:
Select the sound that is produced
when the SET button, MENU button,
etc. are pressed.
AUDIO GUIDE:
Mute or enable the camera’s audio
help guide.
OPERATION VOL:
Adjust the volume of the operation
sounds.
English 132
OPERATION SOUNDS
3
Press the [T/]] or [W/P] button to select the desired setting, and
press the SET button.
h The screen to select operation sounds appears.
<If “TURN ON/OFF” or “AUDIO GUIDE” is selected>
h The respective screen to enable or disable the sound appears.
h Press the [T/]] or [W/P] button to select the desired setting,
and press the SET button.
ON: Activates the sound.
OFF: Deactivates the sound.
<If “SHUTTER” or “KEY SW” is selected>
h The screen to select the operation sounds appears.
h Select from 8 different sounds (A to H).
h You can press the [H] button to preview the selected operation
sound.
h If “OFF” is selected, no sound is produced.
h Press the [T/]] or [W/P] button to select the desired setting,
and press the SET button.
<If “OPERATION VOL” was selected>
h The screen to select the volume for the operation sounds appears.
h You can select an operation sound volume from 1 (minimum) to
7 (maximum).
h Press the [T/]] or [W/P] button to select the volume, and
press the SET button.
4
Press the MENU button.
h The operation sound settings are completed.
HINT
i If you keep the MENU button pressed and turn on the power, the screen to
turn the operation sounds ON/OFF appears at once. You may find this a
convenient procedure to disable the operation sounds in places you do not
want them to be audible.
133 English
POST-VIEW DISPLAY SETTING
Specify the duration that the captured image appears on the monitor (post-
view) after the [
] button is pressed.
1
2
Display the Option Setting Menu [E1] (page 129).
Select “POST VIEW”, and press the
POST VIEW
SET button.
1 sec:
1 sec
2 sec
OFF
The post-view image is displayed for
1 second.
2 sec:
The post-view image is displayed for
2 seconds.
OK
OFF:
The post-view image is not displayed.
3
Select the desired setting, and press the SET button.
h This completes the post-view setting.
English 134
ASSIGN FUNCTIONS TO THE
ARROW BUTTONS
Assign functions (operation shortcuts) to the [G] and [H] buttons when they
are pressed when the Shooting Screen is displayed.
1
2
Display the Option Setting Menu [E1] (page 129).
Select “SHORTCUTS”, and press
SHORTCUTS
the SET button.
h The Shortcuts Screen appears.
: Assign the function when the [G]
button is pressed.
OFF
OFF
: Assign the function when the [H]
RECOMMENDED SETTINGS
button is pressed.
RECOMMENDED SETTINGS:
The most commonly used
settings are automatically
assigned.
OK
3
Select the button to which you wish
to assign the function, and press
the SET button.
h The screen to assign a function to
the button appears.
SHORTCUTS
OFF
OFF:
No operation shortcut
is assigned to the
button.
OK
p AF LOCK: Lock the focus
(page 54).
PAE LOCK: Lock the exposure
setting.
<When
is selected>
+ FOCUS: Set the focus range
(page 94) (except for
-).
m FLASH:
) EXPOSURE: Adjust the exposure (page 104).
s ISO: Set the ISO sensitivity (page 98).
O SELF-TIMER: Set the self-timer (page 89).
DISP. ON/OFF:Turn the shooting settings display on/off.
Set the flash operation (page 62).
135 English
4
5
Press the [T/]] or [W/P] button.
h Display the function you wish to
assign to the button.
SHORTCUTS
FLASH
OK
Press the SET button.
SHORTCUTS
h The selected function is assigned to
the button, and you are returned to
the Shortcuts Screen.
FLASH
EXP COMPENSATION
h To assign functions to the other
button, repeat steps 3 through 5.
RECOMMENDED SETTINGS
OK
<When “RECOMMENDED
SETTINGS” is selected>
6
Press the MENU button.
h The screen to confirm the shortcut
settings appears, and then you are
returned to the OPTION MENU.
h This completes the shortcuts
setting.
SHORTCUTS
<To confirm the assigned
shortcuts>
h On the screen in step 2, press the
MENU button, and the screen to
confirm the shortcut settings
appears.
English 136
NOISE-REDUCTION FUNCTION
Image noise when recording video clips or still images, as well as audio noise
such as from the wind, can be minimized with the noise-reduction function.
1
2
Display the Option Setting Menu [2] (page 129).
Select “NOISE REDUCTION”, and
NOISE REDUCTION
press the SET button.
MOVIE NR:
Set ON/OFF the function to reduce
image noise when recording a video
clip.
MOVIE NR
PHOTO NR
ON
ON
ON
WIND SOUND NR
PHOTO NR:
Turn ON/OFF the image noise
reduction function during still image
shooting.
OK
WIND SOUND NR:
Turn ON/OFF the wind noise reduction function during video clip/audio
recording.
3
4
Select the desired function and press the SET button.
h The screen to select “ON” or “OFF” appears.
ON:
Noise is reduced.
OFF:
Noise is not reduced.
Press the [T/]] or [W/P] button to select the desired setting, and
press the SET button.
h This completes the noise reduction setting.
137 English
ADJUST THE IMAGE QUALITY
The camera can adjust the image quality as the image is captured.
1
2
Display the Option Setting Menu [2] (page 129).
Select “IMAGE SETTINGS”, and
press the SET button.
NORMAL:
IMAGE SETTINGS
NORMAL
VIVID
SOFT
Shoot with image quality at normal.
VIVID:
Color saturation is increased.
SOFT:
SOFT&VIVID
The sharpness is subdued for a
softer image.
OK
SOFT&VIVID:
The sharpness is softened and color
saturation is increased.
3
Select the desired setting, and press the SET button.
h This completes the image quality setting.
English 138
FLICKER-REDUCTION
The flicker-reduction setting reduces the flicker that results when filming video
clips under fluorescent lights and the like where the background lighting
pulsates at the frequency of the power supply.
1
2
Display the Option Setting Menu [2] (page 129).
Select “FLICKER REDUCT”, and
FLICKER REDUCT
press the SET button.
ON:
Turns on the flicker-reduction setting.
OFF:
Turns off the flicker-reduction setting.
ON
OFF
OK
3
Select the desired setting, and press
the SET button.
h This completes the flicker-reduction
setting.
HINT
i If the flicker-reduction setting is used outdoors on a very bright day, a
halation effect, which produces diffused rings of light around bright light
areas, may occur.
i When the flicker-reduction function is set to “ON”, the shutter speed during
video clip recording becomes 1/100 sec.
139 English
MONITOR BRIGHTNESS
Adjust the brightness of the camera’s monitor display. Use this adjustment
when the monitor image is difficult to view because of ambient lighting.
1
2
Display the Option Setting Menu [2] (page 129).
Select “BRIGHTNESS”, and press
BRIGHTNESS
the SET button.
3
Press the [G] or [H] button to set
the brightness, and press the SET
button.
h The monitor brightness is set.
ADJUST
HINT
i The display in step 2 can also be accessed from the Shooting Screen.
Press the MENU button for at least 1 second; the brightness control
display will appear, and you can then adjust the monitor brightness.
English 140
SCREEN LANGUAGE
You can set the monitor of your camera to display the messages in any one of
several languages.
1
2
Display the Option Setting Menu [2] (page 129).
Select “LANGUAGE”, and press the
LANGUAGE
SET button.
ENGLISH
FRANCAIS
DEUTSCH
ESPAÑOL
:
Japanese
English
French
German
Spanish
Italian
ENGLISH:
FRANCAIS:
DEUTSCH:
ESPAÑOL:
ITALIANO:
OK
NEDERLANDS: Dutch
:
Russian
PORTUGUÊS: Portuguese
TÜRKÇE:
Turkish
Thai
:
:
:
:
Korean
Chinese (simplified)
Chinese (traditional)
3
Select the desired language, and press the SET button.
h The selected display language is set.
141 English
TV SYSTEM SETTING
Specify the type of image signal that is output from your camera’s USB/AV
terminal.
1
2
Display the Option Setting Menu [2] (page 129).
Select “TV SYSTEM”, and press the
TV SYSTEM
SET button.
h The TV System Screen appears.
NTSC:
Outputs NTSC video signals.
PAL:
NTSC
PAL
Outputs PAL video signals.
OK
3
Select the desired setting, and press the SET button.
h The selected TV system is set.
HINT
If no image appears on the TV...
i If the TV system setting is not correct for the connected equipment, no
image will appear on the TV.
When set to “PAL” and connected to a TV using the included AV
interface cable (page 155)
Shooting: Images are displayed on the monitor only and do not appear on
the TV.
Playback: Images are displayed on the TV only and do not appear on the
monitor.
English 142
POWER SAVE FUNCTION
Your camera has a “power save” function whereby the power automatically
turns off after a specified period of inactivity. The power save function works
to conserve the battery pack power when the camera is not being used, or to
prevent the battery pack from dying if the camera has accidentally been left
on. You can specify the elapsed time (standby time) before the power save
function is activated.
1
2
Display the Option Setting Menu [3] (page 129).
Select “POWER SAVE”, and press
POWER SAVE
the SET button.
RECORDING:
Set the standby time for the shooting
modes when the battery pack is
used.
RECORDING
PLAYBACK
1 min
5 min
PLAYBACK:
Set the standby time for the playback
modes when the battery pack is
used.
OK
143 English
3
4
Select the desired option, and press the SET button.
h The Set Standby Time Screen appears.
Press the [T/]] or [W/P] button to set the standby time.
[T/]]:
Increases the standby time.
[W/P]:
Decreases the standby time.
5
6
Press the SET button.
Press the MENU button.
h The standby time is set.
English 144
FILE NO. MEMORY
If a newly formatted card is used, the file name (image number) of the
captured image automatically begins from 0001. If the card is subsequently
reformatted, or if a different reformatted card is used, the file names again
begin from 0001. This is because the file number memory function is set to
“OFF”, and consequently it results in more than one card containing images
with the same numbers. By setting the file number memory function to “ON”,
even if the card is reformatted or the card is replaced with another card, the
consecutive numbering of file names continues from the last number
recorded by the camera.
<File number memory function “OFF”>
File name (image number)
Card A
0001, 0002......0012, 0013
Replace card
Card B
0001, 0002......0012, 0013
<File number memory function “ON”>
File name (image number)
Card A
0001, 0002......0012, 0013
Replace card
Card B
0014, 0015....... 0025, 0026
145 English
i If Card B already has files in it when it replaces Card A, file names are
assigned as follows.
When the highest file number on Card B (before replacing) is lower
than the highest file number on Card A: the file name of the next
recorded image continues from last file name recorded on Card A.
Card A
0001, 0002 ..... 0012, 0013
Replace card
Card B
0001, 0002, 0014, 0015 ..... 0025, 0026
Previously recorded files
When the highest file number on Card B (before replacing) is higher
than the highest file number on Card A: the file name of the next
recorded image continues from last file name recorded on Card B.
Card A
0001, 0002 ..... 0012, 0013
Replace card
Card B
0020, 0021, 0022, 0023 ..... 0025, 0026
Previously recorded files
English 146
FILE NO. MEMORY
1
2
Display the Option Setting Menu [3] (page 129).
Select “FILE NO. CONT’D”, and
FILE NO. CONT’D
press the SET button.
ON:
The file number memory function is on.
OFF:
The file number memory function is off.
ON
OFF
OK
3
Select the desired setting, and press the SET button.
h The selected file number memory function is set.
HINT
i Until the file number memory function is turned “OFF”, consecutive file
names are assigned. It is recommended that the file number memory
function be returned to “OFF” at the end of each photography session.
147 English
INITIALIZING THE CARD MEMORY
AND INTERNAL MEMORY
A card must be formatted with this camera:
i After purchasing, when used for the first time, or
i If it was formatted using a personal computer or another digital camera.
The card cannot be formatted if the lock switch is set to the “LOCK” position.
Proceed with the format procedure after setting the lock switch to the
unlocked position.
1
2
Display the Option Setting Menu [3] (page 129).
Select “FORMAT”, and press the
FORMAT
SET button.
<Card format>
h The screen to select the type of
format appears.
h Follow steps 4 to 6.
FORMAT
FULL FORMAT
FORMAT:
A normal formatting is executed.
FULL FORMAT:
OK
The entire card is scanned and
reformatted. It is not possible to
select this when there is no card
installed, or when the remaining
battery charge is low.
<Internal memory format>
h The screen to confirm formatting
appears.
h Follow steps 4 and 5.
3
4
Select the desired format option, and press the SET button.
h The screen to confirm formatting appears.
Select “YES”.
English 148
INITIALIZING THE CARD MEMORY AND
INTERNAL MEMORY
5
Press the SET button.
h Formatting begins.
h During formatting, “Formatting” and “do not power off” are shown on
the monitor.
h The three BGM audio files that were stored in your camera’s internal
memory at the time of purchase can be recovered by formatting the
internal memory.
CAUTION
Caution during formatting
i Do not turn off the power to the camera or eject the card during formatting.
Formatting erases the data
i When a card is formatted, all data recorded on the card is erased.
Protected data (page 107) is also erased, so before formatting a card, any
data you want to keep should be copied to your personal computer’s hard
disk or other storage medium.
Caution regarding disposing/transferring the card (recovering data from
a reformatted card)
i If a card is reformatted or the data is erased from the card using the
camera or a computer, the card’s control data may be merely modified and
the data itself may not be completely erased from the card.
i In some cases it may be possible to recover the data from a reformatted
card using special software for that purpose. However, if the camera is
used to execute a full format, it will be impossible to recover the data even
by the use of data recovery software.
i If you are disposing of a card, it is recommended that you physically
destroy it. If you are transferring the card to someone else to use, it is
recommended that you use the camera’s full format function to reformat
the card, or use commercially available software for erasing card data.
Managing data is the responsibility of the user.
HINT
To cancel formatting
i In step 4, select “NO”, and press the SET button.
149 English
RESETTING THE CAMERA SETTINGS
Reset the camera to the factory-preset settings.
1
2
Display the Option Setting Menu [3] (page 129).
Select “RESET SETTINGS”, and
RESET SETTINGS
press the SET button.
RESET:
Reset to the factory-preset settings.
EXIT:
Do not change the settings, and return
to the Option Setting Menu.
RESET
EXIT
OK
3
Select “RESET”, and press the SET
button.
h The camera settings are reset to the
factory-preset settings.
HINT
i Note that the following settings do not change with this procedure:
Date and time setting
Language setting
TV system setting
English 150
CHECKING THE REMAINING CARD
MEMORY
You can check how many images can be captured and how much recording
time is available on the card. For a table showing the maximum number of
images and recording time for specific cards, please see “Possible No. of
Images/Possible Shooting Time/Possible Recording Time” on page 189.
Checking the remaining number of images and
video recording time
1
Set the camera to the shooting mode
(page 35).
h The remaining number of images
appears in the upper left of the
monitor.
h The remaining video recording time
appears in the upper right of the
monitor.
Remaining number of images
Remaining video
recording time
TV-SHQ
668
01:17:32
h The remaining number of images
and video recording time will differ
depending on the resolution and
compression settings.
For audio recordings
1
Set the camera to the audio
recording mode (page 82).
h The remaining audio recording time
is shown.
Remaining time
668
11:44:37
151 English
HINT
i When the remaining number of images or the remaining video recording
time is “0”, you cannot capture any more images. To capture more images,
either install a new card, or save the images to a computer and then delete
them (page 74) from the card.
i When the remaining number of images or the remaining video recording
time is “0”, it may be possible to capture a few more images by setting a
lower resolution setting (pages 56, 79 and 80), or selecting a different
image quality setting.
English 152
CHECKING THE REMAINING
BATTERY PACK CHARGE
When using the battery pack, the remaining battery pack charge can be
checked on the monitor. Make sure to check this indicator before capturing an
image. For an indication of the possible length of time for battery pack
operation, see page 188.
1
Display the Shooting Menu or
Playback Menu (page 37).
1
h The battery pack remaining
charge indicator appears in the
lower right corner of the monitor.
h Due to the battery pack
2
3
1
2
3
Switch to
simple menu
characteristics, when the ambient
temperature is low,
may
S
N
EXIT
OK
appear early for an incorrect
indication of the remaining
charge.
Battery pack remaining
charge indicator
Also, depending on the conditions
of use of the camera or the
ambient conditions (temperature,
etc.), the indicated remaining
charge may change. Therefore,
this indication can only be used
as a general approximation of the
remaining charge.
Battery pack
remaining
Battery remaining charge
charge indicator
No indication, or
Approx. full.
Power is low.
It will soon be impossible to capture or play
back images.
If this icon flashes when the [
] button is pressed, images cannot be
captured. Recharge the battery pack.
] button or
[
153 English
HINT
i If any file is present, you can also check the remaining battery pack charge
on the Information Screen (page 128).
i Battery life may differ even among battery packs of the same type.
i Depending on the usage of the camera (such as the number of times the
flash is used, the use of the monitor, etc.) or the ambient temperature
(temperatures below 10 °C [50 °F]) the number of images that can be
saved on a fully charged battery pack will vary greatly.
i It is recommended that you prepare an extra battery pack(s) when taking
pictures at a wedding or while traveling, for example, so you don’t miss
capturing images of important moments due to the battery pack power
running out. The same is recommended for taking photos in cold
environments. (In a ski area, for example, the battery pack can be kept
warm in your pocket until ready to use.)
English 154
OTHER DEVICES AND CONNECTIONS
CONNECTING TO A TV
CONNECTING TO A TV
CONNECTING TO A TV
To the USB/AV terminal on the camera
Supplied dedicated AV interface cable
Yellow plug:
To the VIDEO input terminal
White plug:
To the AUDIO input (L) terminal
Red plug:
To the AUDIO input (R) terminal
Switch input to
VIDEO
NOTE
Insert and pull out the cable carefully
i When connecting the cables, make sure that the cable plugs are correctly
oriented and that they match the shapes of the terminal sockets on the
devices. Push the plugs in straight when connecting them. If undue force is
used to connect a cable, it may permanently damage the connector pins in
the terminal socket.
i Do not use excessive force when connecting and disconnecting cables.
Copying (dubbing) images to a DVD recorder
i Please refer to the section on “Dubbing” in the instruction manual for your
DVD recorder.
155 English
PLAYING BACK ON A TV
i After connecting the camera to the television, switch the TV input to the
terminal to which the camera is connected.
i When the camera is connected to a TV, no image appears on the camera’s
monitor.
i The playback method is the same as when viewing images on the
camera’s monitor.
Audio playback: see page 83
i The same playback procedure as when playing back with the camera is
used to play back audio recordings as well.
<About the image display>
When the camera is connected to a TV, the images appear either on the
camera or the TV.
“TV SYSTEM” setting
NTSC
PAL
(page 142)
Supplied AV interface
cable
Not
connected
Not
connected
Connected
Connected
Camera
m
n
m
m
monitor
Recording
mode
m
TV
—
m
—
(Field of
view 90%)
—
m
—
n
n
Camera
monitor
n
Playback
mode
m
m
TV
(Field of
view 90%)
(Field of
view 90%)
m: Output n: Not output
h If the dedicated AV interface cable is connected or disconnected during
recording or playback, recording/playback is discontinued.
English 156
CONNECTING TO A PRINTER
CONNECTING TO A PRINTER
PictBridge MODE
Your camera supports the PictBridge function. By connecting the camera
directly to a PictBridge-enabled printer, the camera’s monitor can be used to
select images and initiate printing (PictBridge printing).
Use the dedicated USB interface cable to connect the camera to a printer.
Print preparations
1
Turn the printer on, and use the supplied USB interface cable to
connect the camera to the printer.
h Connect the camera’s USB/AV terminal to the printer’s USB
connector.
2
Turn on the camera (page 30).
h The USB Connection Screen appears on the camera’s monitor.
SET button
To the USB/AV terminal on the camera
Supplied dedicated USB interface
cable
USB CONNECTION
To USB connector
on the printer
COMPUTER
PRINTER
CANCEL
CANCEL OK
157 English
3
4
Select “PRINTER”, and press the SET button.
The PictBridge printing mode is
PictBridge MENU
activated.
PRINT 1 IMAGE
PRINT ALL IMAGES
INDEX
DPOF
PRINTER SETTINGS
h The camera switches to the
PictBridge printing mode, and the
PictBridge Menu appears.
EXIT
OK
CAUTION
Insert and pull out the cable carefully
i When connecting the cables, make sure that the cable plugs are correctly
oriented and that they match the shapes of the terminal sockets on the
devices. Push the plugs in straight when connecting them. If undue force is
used to connect a cable, it may permanently damage the connector pins in
the terminal socket.
i Do not use excessive force when connecting and disconnecting cables.
Caution when connecting a printer
i If the power to the printer is turned off while it is connected, the camera
may not operate correctly. If the camera does not operate correctly,
disconnect the USB interface cable, turn off the camera, and then
reconnect the cable.
i During PictBridge printing, the camera’s button operation response is
slower.
i If the camera is powered by the battery pack for printing, make sure that
the remaining battery charge is sufficient.
English 158
PRINTING
Printing selected images
Procedure to select one still image and print it.
1
2
Complete the printing setup (page 157).
Select the one image icon Y, and
press the SET button.
h The screen to select images for
printing appears.
PRINT 1 IMAGE 100-0022
:1copy
PRINT
EXIT
3
4
Press the [G] or [H] button to
display the image you wish to
print.
OK
h Specify the image to print.
Specify the number of prints.
1 Press the [T/]] button to
select “COPIES”, and press the
SET button.
PRINT 1 IMAGE 100-0022
copy
:1
2 Press the [T/]] or [W/P]
button to specify the number of
prints.
PRINT
EXIT
3 Press the SET button.
COPIES
h “PRINT” is selected.
5
Press the SET button.
h Printing begins.
HINT
To cancel printing
1 During printing, press the [W/P] button.
h The Confirm Cancel Printing Screen appears.
2 Select “CANCEL”, and press the SET button.
h If “EXIT” is selected and the SET button is pressed, printing resumes.
159 English
Printing all images
Print all of the images on the card.
1
2
Complete the print preparations (page 157).
Select the all images icon u, and
press the SET button.
h The Print All Images Screen
appears.
PRINT ALL IMAGES 100-0022
PRINT
EXIT
3
Select “PRINT”, and press the SET
button.
h Printing begins.
OK
CAUTION
Printing is not possible if there are more than 999 still images in the
card
i Delete unwanted images before printing.
English 160
PRINTING
Making an index print
Make an index print of all the images on the card.
1
2
Complete the print preparations (page 157).
Select the index print icon [, and
press the SET button.
INDEX
100-0022
h The Index Print Screen appears.
PRINT
EXIT
3
Select “PRINT”, and press the SET
button.
h Printing begins.
OK
161 English
Printing images according to printing
instructions (requested images)
Procedure to print all the ordered images.
1
2
Complete the print preparations (page 120), and complete the print
preparations (page 157).
Select the DPOF icon w, and press
DPOF
:2008/12/24
:3copies
100-0022
the SET button.
h The Print Requested Images
Screen appears.
PRINT
EXIT
3
Select “PRINT”, and press the SET
button.
h Printing begins.
OK
h Printing begins about 1 minute
after the SET button is pressed.
HINT
i In step 2, if you press the [G] or [H] button, you can view each image and
confirm its printing instructions.
CAUTION
i Requested images printing w is not possible if a printer is used that does
not support your camera’s DPOF function.
English 162
PRINTING
Changing the printer settings
Images are printed according to settings specified by the camera, such as
paper type, size, layout, printing quality, etc.
1
2
Complete the print preparations (page 157).
Select the printer settings icon v,
PRINTER SETTINGS
and press the SET button.
h The Printer Settings Screen
appears.
MEDIA TYPE:
Specify the type of paper used for
printing.
MEDIA TYPE
PAPER SIZE
LAYOUT
QUALITY
DATE STAMP
PRINTER VALUES
PRINTER VALUES
PRINTER VALUES
PRINTER VALUES
PRINTER VALUES
PAPER SIZE:
OK
Specify the size of paper used for
printing.
LAYOUT:
Specify how the images are to be
arranged on the paper.
QUALITY:
Select the print quality for the
images.
DATE STAMP:
Print the date the photo was taken.
163 English
3
Adjust the printer settings.
1 Press the [T/]] or [W/P]
button to select a printer
setting parameter, and press
the SET button.
PRINTER SETTINGS
MEDIA TYPE
PRINTER VALUES
h The screen to set the selected
parameter appears.
2 Press the [T/]] or [W/P]
button to adjust the setting,
and press the SET button.
h The selected parameter is set,
and you are returned to the
Printer Settings Screen.
OK
<When “MEDIA TYPE” is
selected>
h Follow the same procedure to
adjust the other parameters,
as desired.
h The contents of the settings
that can be made for each
parameter will differ
depending on the printer.
<When “PRINTER VALUES” is
selected>
h The images will be printed
according to the settings specified
on the printer side.
4
Press the MENU button.
h You are returned to the PictBridge Menu.
HINT
i The printer setting parameters will differ depending on the printer that is
connected.
i To use printer functions which do not appear on your camera’s Printer
Settings Screen, select “PRINTER VALUES”.
i If a function set by the camera is not available in the printer, the camera’s
printer settings will automatically change to “PRINTER VALUES”.
English 164
APPENDICES
APPENDICES
COMMONLY ASKED QUESTIONS
If you have a question about the camera operation, you might find the answer
in this compilation of commonly asked questions.
Question
Answer
Action
Why doesn’t the
power turn on?
Due to cold
temperatures, the your pocket to warm
battery pack
temporarily lost its
power.
Place the camera in
it up before using it.
Why is the battery The ambient
Keep the battery
pack in an
environment of 10 to
40 °C (50 to 104 °F).
pack consumed
so quickly even
after it was fully
recharged?
temperature is
very low.
Power
Why doesn’t
recharging end?
The battery pack
life has expired.
Replace with a new
battery pack. If this
is not effective,
consult your dealer.
Why does the
The remaining
battery pack
power is low.
Replace the battery
pack with a fully
charged one.
icon
appear?
Why does the
multi-indicator
flash red?
A recorded file is
being saved on
the card.
Not a malfunction.
Wait until the multi-
indicator turns off.
Why doesn’t the
flash operate?
The camera has
determined that
the image is bright the camera will
Not a malfunction.
Capture the image;
Shooting
enough and the
flash is not
determine when the
flash is necessary.
necessary.
165 English
Question
Answer
Action
Are the settings
retained even
after the camera
is turned off?
—
All settings except
the self-timer and
the exposure
compensation are
retained even after
the camera is turned
off.
Which resolution
setting should I
use?
—
Select the resolution
setting according to
the intended use:
I, U, V, ],
W, R:
Appropriate for
printing letter-size or
Shooting
larger, and for
printing a close-up of
part of a photo
(trimming).
G, t: For
printing standard
photo (photo
service) sizes.
[: For photos
displayed on a web
page, or sent as e-
mail attachments.
English 166
COMMONLY ASKED QUESTIONS
Question
What is the
difference
Answer
—
Action
Because shooting
with the optical
between the
digital zoom and
the optical zoom?
zoom uses the
optics of a physical
lens, you can shoot
without losing
minute details in the
image. The digital
zoom, on the other
hand, works by
magnifying a portion
of the image that
hits the image
sensor and may
produce a coarser
image.
Shooting
How can I get the
distant view into
focus?
—
Set the scene select
function to the
landscape +
mode when
photographing.
Or, set the focus
range setting to
manual focus -,
and set the distance
to ∞.
Set the flicker-
reduction setting to
off.
The video clip I
shot outdoors is
completely white.
—
167 English
Question
Answer
Action
When used in
cold weather, why the monitor
does the image
seem to leave
traces as it
Condition due to
Not a malfunction.
Spots that appear in
the monitor only
appear in the
monitor and will not
be recorded with the
images.
characteristics.
moves?
Monitor
Why does the
displayed image
contain some red,
blue and green
dots, or why are
black spots
visible?
Why is the image The subject was
too bright? too bright.
When capturing an
image, devise a way
to compensate for a
bright subject, for
example, by
changing the
shooting angle.
Why is the image The focus is not
Hold the camera
correctly and slowly
out of focus?
locked properly.
Viewing
images
press the [
button halfway to
lock the focus. Then
]
press the [
]
button all the way to
capture the image.
Why is a part of
the image
missing?
The image was
captured at close
range.
When capturing an
image at close
range, compose the
image using the
monitor.
English 168
COMMONLY ASKED QUESTIONS
Question
Answer
This may happen Play back images
when trying to that were recorded
play back images on a card using this
Action
Why is there no
image (z is
shown)?
stored on a card
from a different
digital camera.
camera.
Why is the
playback image
distorted?
If the subject
Not a malfunction.
This is a
characteristic of the
CMOS sensor.
moves or the
camera is moved
during recording,
a distorted image
may sometimes
occur.
Why isn’t the
magnified image
clear?
Due to the
characteristics of
the camera,
magnified images
appear less clear.
Not a malfunction.
Not a malfunction.
Viewing
images
Why isn’t the
captured image
clear?
The image was
captured using
the digital zoom.
Can I play back
image and sound
files that I edited
using my
—
We cannot
guarantee the
accurate playback of
files that have been
edited using a
computer.
computer?
Why is there a
motor-like sound
during video clip
playback?
The sound of the
camera’s
mechanical action
was recorded.
Not a malfunction.
169 English
Question
Why does a
message appear
during PictBridge printer.
printing?
Answer
There is a
problem with the
Action
Please refer to the
instruction manual
for your printer.
Printing
The “Cannot edit
video clips with
unlike settings”
message
You have
attempted to join
video clips having resolution and frame
different
resolutions or
frame rates.
Select video clips
that have the same
rate.
appears.
Why does the
“Card full”
message appear? on the card.
There is no more
available memory files, or use a card
Delete unnecessary
that has more
memory available.
Misc.
Why does the
“Card is
protected”
The lock switch on Move the lock switch
the card is in the
locked (protect)
to the unlocked
position.
message appear? position.
Why can’t the
camera be
operated?
A temporary
Remove the battery
pack from the
camera, wait a few
minutes, then
internal circuitry
problem may be
the cause.
reinstall the battery
pack and try again.
English 170
COMMONLY ASKED QUESTIONS
Question
Answer
Action
A problem such
as inability to
record or play
back occurs.
The card contains After saving your
files that were
saved using a
files to a different
medium, format the
device other than card.
this camera.
Can I use my
camera abroad?
—
When the camera is
connected to a TV,
you can switch the
camera’s video
output to NTSC or
PAL. If you have
questions about
using the charger
and power cord
abroad, please
consult with a dealer
near you for advice.
Misc.
Why does the
“System error”
A problem has
occurred within
Check the following
items:
message appear? the camera or
card.
1 Remove the
card and then
install it again.
2 Remove the
battery pack and
then install it
again.
3 Install a different
card.
If “System error” still
appears after
performing the
above steps, then
take the camera to
the dealer for
service.
171 English
TROUBLESHOOTING
Before taking your camera to the repair shop, check the following table for a
possible solution to the problem.
Camera
Reference
page
Problem
Cause
Action
No power.
The battery
pack is dead.
Recharge the
battery pack, or
replace with a
new battery
pack.
23, 25
The battery
pack has not
been inserted
correctly.
Reinsert the
battery pack,
making sure to
orient it
correctly.
Power
A blinking
The battery
Wait for the
temperature
warning icon
\ is shown,
and the
pack is too hot. battery pack to
cool down.
29
30
camera does
not turn on.
The camera
turns off by
itself.
The power
Turn on the
camera again.
save function
is operating.
An image is
not captured
when the
The power is
not turned on.
If the power
save function
was activated,
turn on the
camera before
shooting.
[
[
] button or
] button is
Shooting pressed.
30
If the camera
was turned off,
press the ON/
OFF button to
turn it on.
English 172
TROUBLESHOOTING
Reference
page
Problem
Cause
Action
An image is
not captured
when the
The maximum Install a new
28
number of
card.
images that
Delete the
[
[
] button or can be
] button is captured or the
images that are
not necessary.
pressed.
maximum
video clip
recording time
has been
74
reached.
The flash does The flash off
Set the flash to
automatic flash
mode or forced
flash mode.
not operate.
mode is
selected.
62, 88
23, 25
Shooting
The battery
pack is dead.
Recharge the
battery pack, or
replace with a
new battery
pack.
The digital
zoom does not is set to I.
work. The digital
The still image Set the still
image to U
or lower.
80, 102
zoom setting is Set the digital
set to “OFF”.
zoom setting to
“ON”.
173 English
Reference
page
Problem
Cause
Action
Install a
A warning tone The battery
(beep-beep- pack is
beep) sounds, consumed.
and it is not
sufficiently
recharged
battery pack.
23, 25
possible to
take a picture
using the self-
timer.
When zooming The optical
Not a
in or out, the
zoom
movement
stops
zoom has
moved to the
maximum
magnification
position.
malfunction.
Release the
[T/]] button
once, then
press it again.
66
98
momentarily.
Shooting
There is noise The ISO
in the captured sensitivity
Set the ISO
sensitivity to a
lower setting.
image.
setting is too
high.
When
This occurs
when the
shutter speed
is too fast.
Set the ISO
sensitivity to
v or less.
recording a
video clip
under
fluorescent
lights, a
98
noticeable
flicker appears
in the image.
English 174
TROUBLESHOOTING
Reference
page
Problem
Cause
Action
The \ icon
The camera’s
internal
shooting is not temperature is wait for the
Discontinue
shooting, and
appears, and
Shooting
Monitor
—
possible.
high.
camera to cool
down before
using it again.
No playback
image
appears.
The camera is Press the REC/
not set to the
playback
mode.
PLAY button to
set the camera
to the playback
mode.
35
175 English
Reference
page
Problem
Cause
Action
Hold the
The image is
too dark.
The flash was
blocked by a
camera
finger or other correctly, and
53
object.
make sure the
flash is not
obstructed.
The subject
was too far
away.
Capture the
image in the
range of
operation of the
flash.
187
The subject
was lit from
behind.
Use the forced
flash mode.
62, 88
104
Viewing
images
Use the
exposure
compensation
function.
Use the spot
light-measuring
mode.
97
98
There is not
enough light.
Adjust the ISO
sensitivity
setting.
The video clip
picture is
flickering.
The video clip
was filmed
under
Set the flicker-
reduction
setting to on.
139
fluorescent
lighting.
English 176
TROUBLESHOOTING
Reference
page
Problem
Cause
Action
Select a
different flash
mode.
The image is
too bright.
The forced
flash mode is
selected.
62, 88
104
The subject
was too bright. exposure
compensation
Use the
function.
Viewing
images
The ISO
sensitivity
setting is
incorrect.
Set the ISO
sensitivity to
98
=
.
Red-eye
The red-eye
Not a
malfunction.
correction was effect area
not successful. could not be
recognized.
111
177 English
Reference
page
Problem
Cause
Action
The image is
not in focus.
The subject is
too close to the image with the
camera.
Capture the
subject within
the
photographable
The focus
setting is not
correct.
57, 96
range.
Select the
correct focus
setting for your
needs.
The camera
moved when
Hold the
camera
correctly and
slowly press
the [
Viewing
images
the [
]
button was
pressed.
(camera
shake)
]
button halfway
to lock the
53, 60
focus. Then
press the [
button all the
way to capture
the image.
The focus is
not locked
properly.
]
The lens is
dirty.
Clean the lens.
—
English 178
TROUBLESHOOTING
Reference
page
Problem
Cause
Action
The colors of
the images
captured
indoors are not
correct.
This is due to
ambient
lighting.
Capture the
image using
the forced flash
mode.
62, 88
99
The white
balancesetting balance setting
Set the white
is incorrect.
correctly.
A part of the
image is
missing.
The strap or a
finger was
blocking the
lens.
Hold the
camera
correctly, and
make sure the
lens is not
obstructed.
53
Viewing
images
“No image” is
shown.
There is no file Play back after
in the installed capturing
card.
images or
making audio
recordings.
—
73
During audio
playback,there volume setting playback
is no sound.
The playback
Adjust the
on the camera volume.
is too low.
There is no
color in the
image.
The TV output Select the
setting is not
correct.
correct TV
output setting.
Connecting
to a TV
142
The image is
distorted.
179 English
Reference
page
Problem
Cause
Action
No image or
sound.
The camera is Follow the
not correctly
connected to
the TV.
instructions to
make the
connection
correctly.
142, 155
Connecting
to a TV
The TV input is Set the input
not set
on the TV to
“VIDEO”.
correctly.
The edge of
the image is
cut off.
This is a
characteristic
of the TV.
Not a
malfunction.
—
You cannot
edit or rotate
an image.
The protect
mode is set.
Cancel the
protect mode.
Image
editing
107
The battery
pack is not
charging.
Correctly
insert the
battery pack in pack is
Make sure that
the battery
Charging
the charger.
correctly
23
oriented when
inserting it in
the charger.
The “Image is
protected”
message
appears and
the file cannot
be deleted.
You have
Set the protect
setting for the
file to
attempted to
delete a file
that is
protected from
accidental
erasure.
Misc.
“UNLOCK”.
107
English 180
TROUBLESHOOTING
Reference
page
Problem
Cause
The audio
Action
The audio
Set the audio
guide does not guide setting is guide setting to
132
sound.
set to “OFF”.
“ON”.
The recording
The recording
Depending on
capacity is less capacity is less the card, the
than that
indicated in the specified for
section
“Possible No.
of Images/
Possible
than the value
capacity may
be less than the
specified value.
Please refer to
the instructions
that
the card.
—
Shooting Time/
Possible
accompanied
the card.
Recording
Time”
(page 189)
.
The battery
pack appears
to be swollen.
Normal change Not a safety
Misc.
occurring with
battery use.
Even with
hazard. If the
battery quickly
becomes
normal correct depleted, for
use of the
lithium-ion
example, it has
reached the
battery, it has a end of its
tendency to
swell as the
number of
charge and
discharge
service life.
Replace it with
a new battery
pack.
—
cycles adds up
and it gradually
approaches
the end of its
service life.
181 English
Notes regarding the Scene Select feature and
filters
Scene Select
Setting
Remarks
Sports
a
Portrait
>
Landscape
+
Focus range: + cannot be selected.
Night view portrait
/
Snow & beach
k
Underwater
[
Fireworks
+
Focus range: Fixed at *.
Flash: Fixed at l.
Resolution: Only G or [ can be selected.
Focus range: + cannot be selected.
Flash: Fixed at l.
Lamp*
Q
Still image NR: Fixed at “OFF”.
* When recording a video clip in dark surroundings, the shutter speed
decreases to 1/15 sec in order to produce a sufficiently bright image.
However, when the flicker-reduction function is set to “ON”, the shutter
speed during video clip recording becomes 1/100 sec or 1/120 sec.
English 182
TROUBLESHOOTING
Filter
Setting
Remarks
Cosmetic
%
Monochrome
Focus range: + cannot be selected.
W
Sepia
,
About the scene select function and focus range
settings
i The scene select function changes to = when the focus range is set to
+.
i Even if you set the focus range to *, + or -, it changes to -
when the scene select function is set to any setting other than =.
183 English
SPECIFICATIONS
Camera
Type
Digital Movie Camera (recording and playback)
Recorded image
file format
Still images:
JPEG format (DCF, DPOF, Exif 2.2 compliant)
Note: Designed mainly by the Japan Electronics
and Information Technology Industries
Association (JEITA), DCF (Design rule for
Camera File system) is standard for digital
still camera image files to provide
interoperability between digital photography
devices for the images stored on removable
memory cards. However, it is not
guaranteed that all devices will support the
DCF standard.
Video clips:
Conforms to ISO-standard MPEG-4 AVC/H.264
Audio:
MPEG-4 audio (AAC compression)
48 kHz sampling rate, 16-bit stereo format
Data storage
media
Internal memory: Approx. 44 MB
SD Memory Card (accepts a maximum 32 GB
SDHC Memory Card)
Image sensor/
Camera effective
CMOS sensor, approx. 8 million pixels
number of pixels
* Video clip files recorded with models VPC-CA65 and VPC-CG65 are in
the same H.264 format as this model. However, such files cannot be
played back, since they are not compatible due to differences such as the
data compression method.
English 184
SPECIFICATIONS
Still image
shooting mode
(recording
I: 4000 × 3000 pixels
U: 3264 × 2448 pixels (approx. 8 million pixels:
low compression)
resolution)
V: 3264 × 2448 pixels (approx. 8 million pixels:
normal compression)
]: 3264 × 1840 pixels (approx. 6 million pixels:
low comoression)
W: 1840 × 2448 pixels (approx. 4.5 million pixels,
portrait orientation)
G: 1600 × 1200 pixels (approx. 2 million pixels)
[: 640 × 480 pixels (approx. 300,000 pixels)
R: 3264 × 2448 pixels (approx. 8 million pixels,
sequential shots)
t: 1600 × 1200 pixels (approx. 2 million pixels,
sequential shots)
Video clip
recording mode
(recording
T: 640 × 480 pixels, 60 frames per second
): 640 × 480 pixels, 30 frames per second (high
bit rate)
resolution)
B: 640 × 480 pixels, 30 frames per second
(standard bit rate)
l: 320 × 240 pixels, 30 frames per second
d: 320 × 240 pixels, 15 frames per second
* The 60 fps frame rate of this camera is 59.94 fps,
the 30 fps frame rate is 29.97 fps, and the 15 fps
frame rate is 14.985 fps.
White balance
Lens
Full-auto TTL, manual setting possible
Optical 5.0×
f = 6.3 mm to 31.7 mm (35 mm film
camera conversion 38 mm to
190 mm)
zoom lens
Autofocus, 9 groups, 12 elements
(including three with five aspheric
surfaces)
Galvanometer iris
Internal ND filter
Aperture
Open F = 3.5 (Wide) to 4.7 (Tele)
185 English
Exposure control
type
Exposure compensation available from the Shooting
Setting Screen (0 1.8 EV in 0.3 EV steps)
Light-measuring
mode
Multi-section measuring, center-weighted
measuring, spot measuring
Range
Total mode:
10 cm (3.94 in.) to infinity (Wide end)
80 cm (31.50 in.) to infinity (Tele end)
Normal mode:
80 cm (31.50 in.) to infinity
Super macro mode:
1 cm (0.39 in.) to 80 cm (31.50 in.) (Wide end
only)
Digital zoom
For shooting:
1× to approx. 12×
For playback:
1× to 62.5× (varies with resolution)
Shutter speed
Still image shooting mode: 1/2 to 1/1,500 sec.
(Maximum approx. 2 seconds when scene select
function set to lamp mode Q)
(During flash: 1/30 to 1/1,500 sec.)
Sequential shots mode: 1/15 to 1/1,500 sec. (no
flash)
Video clip recording mode: 1/30 to 1/10,000 sec.
(1/15 sec. max.: when scene select function is set
to lamp mode Q)
Sensitivity
Video clip recording mode:
Auto (ISO 50 to 1600)/ISO 50, ISO 100, ISO 200,
ISO 400, ISO 800, ISO 1600 (switchable from the
Shooting Setting Screen)
(Maximum ISO sensitivity up to ISO 3200: at high
sensitivity mode setting)
Still image shooting mode (standard output
sensitivity*):
Auto (ISO 50 to 400)/ISO 50, ISO 100, ISO 200,
ISO 400, ISO 800, ISO 1600 (switchable from the
Shooting Setting Screen)
* Sensitivity measured in compliance with the
ISO standard (ISO 12232:2006).
English 186
SPECIFICATIONS
Minimum subject
illumination
Approx. 4 lux: ), high sensitivity mode or scene
select Qfunction, 1/15 sec
Approx. 15 lux: :, scene select .function,1/30
sec
Image stabilizer
Monitor
Electronic (video clip recording mode or still image
shooting mode)
2.5" (6.4 cm) low-temperature polysilicon TFT
transmissive color liquid crystal, approx.
150,000 pixels
Flash working
range
GN = 3
Approx. 10 cm (3.94 in.) to 1.7 m (5.58 ft.) (Wide)
Approx. 80 cm (31.50 in.) to 1.3 m (4.27 ft.) (Tele)
Flash modes
Focus
Auto-flash, forced flash, flash off
TTL-type AF (still image shooting mode: 9-point
range finder/spot focus; video clip recording mode:
Continuous focus), manual focus
Self-timer
Approx. 2-second delay, 10-second delay
Ambient
environment
Temperature
0 to 40 °C (32 to 104 °F) (operation),
–20 to 60 °C (–4 to 140 °F) (storage)
Humidity
30 to 90% (operating, no
condensation)
10 to 90% (storage, no
condensation)
Water-resistant
Power supply
Compliant with JIS protection grade 8 standards
(according to tests conducted in-house by Sanyo)
Battery pack
(supplied)
Li-ion battery pack (DB-L20):
1 supplied
AC adaptor
(sold
separately)
VAR-G8
For use with DC adaptor VAR-A2
(sold separately)
Power consumption
3.3 W (When using the Li-ion
battery during recording)
Dimensions (excluding protrusions) 70.4 (W) × 111.4 (H) × 40.5 (D) mm
2.77 (W) × 4.39 (H) × 1.59 (D) in.
(Maximum dimensions)
Volume: Approx. 192 cc
Weight
Approx. 239 g (8.43 oz.) (camera
only [without battery pack and card])
187 English
Camera connectors
USB/AV
Dedicated regrouped jack
(communication/audio
and video output)
terminal
Audio
output
310 mVrms (–8 dBs), 47 kΩ, stereo
Video
output
1.0 Vp-p, 75 Ω unbalanced, sync
negative, composite video, NTSC
color TV system/PAL TV system
(switchable from the Option Setting
Menu)
USB
USB 2.0 High Speed
PC camera: USB video class
Battery life
Shooting
Still image
shooting mode
Approx. 205 images:
CIPA standard (when a Sandisk
2 GB SD Memory Card is used)
Video clip
recording mode
Approx. 75 minutes:
Recorded in b mode
Playback
Approx. 170 minutes:
Monitor on, continuous playback
i Until battery pack runs out when using a fully charged battery pack at a
25 °C (77 °F) ambient temperature.
i The operation time may vary depending on the conditions of the battery
pack and the conditions of use. Especially when used at temperatures
below 10 °C (50 °F), the battery pack operation time is significantly
reduced.
English 188
SPECIFICATIONS
Possible No. of Images/Possible Shooting Time/
Possible Recording Time
Shooting/
recording
mode
SD Memory Card
Resolution
setting
Internal
memory
2 GB
8 GB
I
U
V
]
W
t
[
R
t
T
)
B
l
d
11 images
11 images
16 images
22 images
29 images
67 images
503 images
503 images
755 images
998 images
1,310 images
2,020 images
2,020 images
3,030 images
4,010 images
5,290 images
Still image
mode
2,940 images 11,800 images
344 images 15,400 images 62,200 images
16 images
67 images
755 images
3,030 images
2,940 images 11,800 images
56 sec. 42 min. 30 sec.
2 hr. 51 min.
5 hr. 32 min.
8 hr. 3 min.
1 min. 49 sec.
2 min. 40 sec.
7 min.
1 hr. 22 min.
2 hr.
Video clip
mode
5 hr. 15 min.
7 hr. 35 min.
21 hr. 10 min.
30 hr. 30 min.
10 min. 5 sec.
Audio
recording
mode
—
43 min. 2 sec.
32 hr. 22 min.
130 hr.
i
If the continuous recording time of a voice memo exceeds about 13 hours, of a
video clip whose resolution setting is exceeds about 5 hours 30 minutes,
or of a video clip whose resolution setting is exceeds about 7 hours, the
recorded file is saved once, and the recording continues in a new file. When
recording a video clip whose resolution setting is other than or , and
l
d
l
d
the file size exceeds 4 GB, the recorded file is saved once, and the recording
continues in a new file. (These 4 GB segments are automatically created. The
recording session continues until you stop recording, but video clip or voice
memo recording is temporarily interrupted while the file is being saved.)
The above values apply when an SD Memory Card by Sandisk is used.
Even with cards of the same capacity, the amount of data that can actually be
stored may differ depending on the card brand, etc.
The continuous shooting time for each video clip will differ depending, for
example, on the card capacity, environmental conditions (temperature and
shooting conditions, etc.).
i
i
i
189 English
Concerning the multi-indicator
The camera’s multi-indicator will light or flash depending on the
different camera operations.
Multi-indicator
Multi-indicator
status
Color
Camera status
Connected to
computer or printer
(USB)
Lit
Green
Power save mode
activated
Flashing
Slow
During self-timer
operation
Red Flashing
Accessing internal
memory/card data
Fast
Connected to TV/
VIDEO (AV)
Orange
Lit
English 190
SPECIFICATIONS
Supplied battery pack charger
Part No.
VAR-L20NI
AC 100 to 240 V, 50 to 60 Hz, 10 VA,
MAX: 0.1 A
Power source
Rated output
DC 4.2 V, 650 mA
Compatible batteries
Supplied or separately sold Lithium-ion
battery pack (DB-L20)
0 to 40 °C (32 to 104°F) (when charging)
–20 to 60 °C (–4 to 140°F) (storage)
Temperature
Humidity
Ambient
environment
10 to 90% (no condensation)
46 (W) × 21.2 (H) × 92 (D) mm
1.81" (W) × 0.83" (H) × 3.62" (D)
Dimensions
Weight (without power cord)
Approx. 55 g (1.9 oz.)
Power cord
VPC-CA8EX
rated value
AC 250 V, 2.5 A
i The VPC-CA8GX model is supplied with a power cord that is appropriate
for the region of destination.
i When using the supplied battery pack charger abroad, the power cord may
need to be replaced in accordance with local requirements. Please contact
your local dealer for details.
Supplied Li-ion battery pack
Model number
Voltage
DB-L20
3.7 V
Capacity
720 mAh
Ambient
environment
Temperature
Humidity
0 to 40 °C (32 to 104 °F) (during use,
when charging)
–10 to 30 °C (14 to 86 °F) (storage)
10 to 90% (no condensation)
Dimensions
Weight
39.4 (W) × 6.0 (H) × 35.5 (D) mm
1.55 (W) × 0.24 (H) × 1.40 (D) in.
Approx. 19 g (0.7 oz.)
191 English
Others
Mac OS and QuickTime are trademarks of Apple Inc., registered in the U.S.
and other countries.
Microsoft and Windows are registered trademarks of Microsoft Corporation in
the USA and other countries.
Pentium is a registered trademark of Intel Corporation (USA).
®
®
®
In this manual, the Microsoft Windows 2000 operating system, Microsoft
®
®
®
Windows XP operating system, and Microsoft Windows Vista operating
system are collectively referred to as “Windows”.
TM
®
Software Red Eye by FotoNation 2003-2005 is a trademark of FotoNation
Inc.
All rights reserved. Adobe and Adobe Premiere Elements are either
registered trademarks or trademarks of Adobe Systems Incorporated in the
United States and/or other countries.
©
Red Eye software 2003-2005 FotoNation In Camera Red Eye - covered by
U.S. Patent No. 6,407,777. Other patents Pending.
SDHC is a trademark.
All other company and product names are registered trademarks or
trademarks of their respective owners.
CAUTION
i It is forbidden to copy this manual, whole or in part, without prior written
permission.
i All images and illustrations given in this manual are for explanation
purposes and may differ slightly from that of the actual product. Also,
actual specifications are subject to change without prior notice and
therefore may differ from the contents of this manual.
English 192
SPECIFICATIONS
Before capturing those important shots, be sure to first take a
test shot to confirm that your camera is set up and ready to go
i Sanyo Electric shall not be held responsible for any problems resulting
from the use of this camera.
i Sanyo Electric declines all responsibility for damages due to improper use
of the camera, failure to adhere to the instructions given in this manual, or
repairs or changes done by those other than a technician authorized by the
manufacturer.
i Sanyo Electric shall not be held responsible for any damage caused by
optional devices or consumable items used with the camera other than
those supplied with the camera or those specified by Sanyo Electric.
i Sanyo Electric shall not be held responsible for any losses or loss of
revenue resulting from the loss of data caused by the malfunction, or the
repairing of a malfunction, of the camera.
i The images captured with this camera will differ in quality from pictures
taken with a standard film camera.
193 English
HINTS FOR TAKING PICTURES
Taking great pictures in difficult surroundings is easier than you might think.
By keeping a few points in mind and choosing the correct settings, you can
create photos that you’ll be proud to display and share.
If images are blurred even when the autofocus is
used
Your camera employs an autofocus function. When you snap a picture using
the autofocus, the camera automatically adjusts the settings so that the
image will be in focus. If you are getting blurred images even when using the
autofocus, one or more of the following might be the reason.
k How the autofocus works
The autofocus is activated when the [
Press the [ ] button slightly, and the target mark will appear on the monitor
to indicate that the autofocus has been activated. Next, continue to gently
press the [ ] button all the way to snap the picture. This two-step method is
] button is gently pressed halfway.
the way to ensure that your photos are perfectly focused.
<The shutter speed and aperture are displayed>
i In the NORMAL mode, the shutter speed and aperture settings are shown
on the Shooting Screen. You can use them as a reference when shooting.
k Reasons for unfocused images
1 The [
] button was pressed all the way in one step.
2 After the image was focused, the subject moved.
h Even if camera focuses the subject once, if the distance between the
camera and the subject is changed, the subject may become out of
focus.
3 The focus setting is not set for the correct distance.
h If you shoot a close-up subject with the camera set to the normal focus
mode, or if you shoot a subject at normal distance with the camera set
to the super macro (close-up) mode (pages 57 and 94), the image will
not be in focus.
k Preventing blurred images
1 Confirm that the camera is set to the correct focus mode for your subject.
2 Hold the camera correctly, and press the [
3 Wait for the target mark to appear in the monitor, and holding the camera
steady, gently continue to press the [ ] button all the way down.
] button halfway.
Following these steps for a gentle but firm pressing of the [
ensure that you get beautifully focused photos.
] button will
English 194
HINTS FOR TAKING PICTURES
Photographing a moving subject
Situation: You would like to snap an action shot of a moving child or pet. The
autofocus is activated, but because the subject is moving, the image may be
blurred. In particular, when the distance between the camera and the subject
is changing, it is difficult to lock the focus on the subject. Here are some hints
for successfully capturing images of moving subjects.
k Reasons for unfocused images
When the [
] button is gently pressed halfway, the camera’s autofocus
works by determining the distance between the camera and the subject.
Once the subject is in focus, if it then moves before the picture is snapped,
the image may be out of focus. This often happens when you once lock the
focus on a subject and then wait for the right moment to snap the picture.
And, conversely, a blurred image may result if you press the [
] button all
the way in one step in an attempt to quickly capture an action scene, thus
failing to activate the autofocus in time.
k Preventing blurred images (How to use the manual focus [page 95])
In addition to the autofocus, a manual focus mode is also incorporated in your
camera. In the autofocus mode, the distance between the camera and the
subject is automatically determined when you press the [
] button halfway.
In contrast to this, with the manual focus mode, you manually set the focus by
specifying the correct distance between the camera and the subject before
taking the picture.
k How to photograph a moving subject
1 Set the camera’s focus mode to the manual focus. Set the focus distance
to the correct distance between the camera and the subject.
2 When the subject is at the set focus distance, gently press the [
button all the way down.
]
<Advantage of using the manual focus>
i Images can be quickly captured without waiting for the autofocus to
activate.
i Because you are presetting the focus distance, the focus can be more
accurate.
<Using the manual focus effectively>
i When photographing a moving subject, press the [
] button just before
the subject reaches the focus distance, and the shutter will be released
when the subject is at the correct distance.
i Use manual focus to avoid incorrectly focused images when there is an
object between the camera and the subject you wish to focus on.
195 English
Shooting portraits (portrait mode >)
Points:
i Choose a background that doesn’t detract from your subject.
i Move in close to your subject.
i Pay attention to lighting and how it affects your subject.
NOTE
i If the background is distracting, it will not show your subject to his best
advantage. Move in closer to your subject or zoom in so that the
background does not compete with the subject.
i In portrait photography your subject is clearly the central figure, so try
techniques that allow the subject to stand out.
i If light is coming from behind your subject (backlit), his face will appear
dark. You can get a better picture by using the flash, for example, or
changing the exposure compensation setting.
Photographing moving subjects (sports mode a)
Points:
i Match the camera’s movement with that of the subject.
i Set the zoom to the Wide end (wide-angle).
i Don’t be too hesitant to press the [
] button, or you’ll miss the action.
NOTE
i Tips to not missing those great action shots: Make sure you’re holding the
camera correctly. Keep the subject in the lens at all times, moving the
camera with him while waiting for the right shot. Move your whole body–not
just your arms–with the camera while shooting.
i Blurred images are more likely when the zoom is set to the Tele end than
the Wide end. Set the zoom as close as possible to the Wide end.
i Learn to press the [
] button quickly yet smoothly the instant your photo
chance occurs.
English 196
HINTS FOR TAKING PICTURES
Night photography (night view portrait mode /)
Points:
i Avoid camera shake.
i Increase the ISO sensitivity.
NOTE
i Camera shutter speed during night photography is considerable slower, so
there is a much greater chance that your photographed images will be
blurry. Stabilize the camera when shooting.
i You can photograph your subject with the night scene in the background by
using the flash. Be careful not to shoot too close to the subject, however, or
your subject’s face will appear too bright.
i After the flash operates, keep the camera and the subjects motionless for
about 2 seconds.
Photographing scenery (landscape mode +)
Points:
i Shoot using a high resolution.
i For zoom photography, use the optical zoom.
i Pay attention to picture composition.
NOTE
i When shooting with a wide-angle setting, or if you intend to enlarge the
photo, the higher the resolution, the better.
i To zoom in on distant scenery, it’s better to use the optical zoom. Using the
digital zoom produces a coarser image. Hold the camera securely, keeping
your elbows close to your body and making sure the camera is stable.
Taking care to stabilize the camera will increase the likelihood of getting a
clear photo.
i Don’t forget to pay attention to picture composition; note perspective and
be aware of how the placement of objects affects the scene.
197 English
SANYO Electric Co., Ltd.
|