Sanyo LNS S02Z User Manual

LCD PROJECTOR LENS  
MODEL NO. LNS-S02Z  
LENS REPLACEMENT  
AND INSTALLATION PROCEDURES  
NOTES ON REPLACEMENT AND INSTALLATION  
The procedures and the needed pars for lens installation depend on the type of  
cabinet. Before installing or replacing the lens, make sure the type of cabinet and be  
sure to refer to the Installation Manual corresponding with your projector.  
When installing or replacing the lens, make sure the Lens Model No. matches with  
your projector. Refer to the catalog, or contact your sales dealer for the proper Lens  
Model No.  
TYPE OF THE CABINET AND REFERENCE INSTALLATION MANUAL  
Refer to the Installation Manual corresponding to your projector.  
(See the chart below.)  
Type of the Cabinet  
Reference Installation Manual  
Refer to this manual.  
Other than the above cabinet  
design.  
Refer to the Installation Manual  
supplied with the Projector.  
LENS REPLACEMENT AND INSTALLATION PROCEDURE  
1
5
Perform the steps  
to  
for lens replacement and installation.  
UPPER LENS COVER  
C
REMOVE THE LENS COVER. (See figure-1)  
1
1. Remove screws A (2 screws).  
2. Pull down the lower lens cover while pushing  
the part D, then remove it.  
3. Remove screws B (2 screws).  
B
4. Remove screws C (2 screws) and remove  
upper lens cover.  
D
D
Fig-1  
A
LOWER LENS COVER  
REMOVE THE COVER PLATE OF THE LENS COVER. (See figure-2)  
2
Remove 2 screws and pull down the plate.  
4
(At the step  
, insert the light-block sheet in  
the same position as the removed cover plate  
has been placed. Two screws are not used.)  
COVER PLATE  
Fig-2  
INSTALL THE LENS. (See figure-3)  
3
1. Remove protective caps(front and back) on the  
lens.  
LENS MOUNTING BRACKET  
2. Mount the lens on mounting bracket of the main  
cabinet with 4 screws.Use the screws included  
with the lens.  
Use the driver included with the lens to fasten the  
screws. (After using, save it for latter use.)  
3. Connect the lead connector of the lens motor to  
the “K16B” on the circuit board as  
shown in figure-4.  
4. Fasten the lens motor lead at the  
A, B points with wire holder as  
shown in figure-4.  
ATTACHED DRIVER  
LENS MOTOR  
Fig-3  
Figure shown inside of the cabinet.  
LENS MOTOR  
(D)  
(D)  
(D)  
(D)  
B
A
WIRE HOLDER  
LENS MOTOR LEAD  
CONNECTOR “ K16B”  
Fig-4  
INSTALL THE LIGHT-BLOCK SHEET. (See figure-5)  
4
Install the light-block sheet around the lens as  
shown in the illustration.  
(Use the sheet included with the lens.)  
Set the light-block sheet, so that the  
large rounder side is set over the lens.  
Set the light-block sheet, so that the large rounder  
side is set over the lens.  
Fig-5  
LIGHT-BLOCK SHEET  
MOUNT THE LENS COVER. (See figure-6)  
UPPER LENS COVER  
5
A
When in install the both upper and lower lens cov-  
ers, install the light-block sheet so that it should be  
placed in the guide slot of the lens cover. If the  
installation of the light-block sheet is incorrect, there  
will be the space between lens and the lens cover,  
so that it will be the cause of leakage of light or the  
dust entering at the main cabinet.  
1. Insert the upper part lens cover and fix  
them with screws A (4 screws).  
A
2. Insert the lower part lens cover and fix them  
with screws B. (2 screws).  
B
Fig-6  
LOWER LENS COVER  

Victory Refrigeration VDW 50 18 User Manual
Victor Technology 1208 2 Series User Manual
Toastmaster MJFP8W User Manual
Sungale Cable Box STB370 User Manual
Sony Handycam Vision CCD TRV78E User Manual
Sony Handycam HDR XR200E User Manual
Sony CC 222 User Manual
Smith Cast Iron Boilers GB300 User Manual
Samsung WEP430 User Manual
Samsung SMX K44BN User Manual