OPERATING
INSTRUCTIONS
FXCD-1350
Fold Down Design Full Panel Detachable
FM Stereo/AM Receiver
Auto Reverse Cassette Player
Compact Disc Player
With CD Changer Controller
ISO Mounting with Removable Trim Ring
(English)
GB
E
OPERATING INSTRUCTIONS. . . . . . . . . . . . . . . . . . . 1~29
(Español)
LIBRITO DE INSTRUCCIONES . . . . . . . . . . . . . . . . . 30~57
English
CONTENTS
COMPACT DISC CARE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
REMOTE CONTROLLER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
DIGITAL DISPLAY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
DETACHABLE FRONT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
GENERAL OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
RADIO OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
TAPE OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
CD OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
CD CHANGER OPERATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
ERROR SIGNS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
CLOCK. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
HINTS FOR PROPER AND SAFE OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
TROUBLESHOOTING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
ACCESSORIES AND HARDWARE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
UNIT REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
ELECTRICAL CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
LINE OUT / CD CHANGER CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
NOTE
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, If not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
CAUTION
• This unit is designed to operate on 12 volts DC, NEGATIVE ground electrical systems only.
•
When fuse replacement is necessary, use only a 15 amp fuse. Do not replace with a higher rated fuse.
If the fuse blows often, carefully check all electrical connections for any short circuits and have your
car's voltage regulator checked also.
• Do not install the unit where it will be exposed to direct sunlight or hot air discharged from the car heater.
• Do not expose the unit to water or moisture.
• To avoid damaging the unit, never insert anything other than a compact disc into the disc slot.
• This unit should not be adjusted or repaired by anyone except qualified service personnel.
If servicing is required, return the unit to an authorized SANYO mobile audio dealer.
• Use of controls or adjustments or performance of procedures other than those specified herein may
result in hazardous radiation exposure.
• Changes or modifications not expressly approved by Sanyo may void the user's authority to operate
this equipment.
-2-
COMPACT DISC CARE
Dirt, dust, scratches and warpage can cause a deterioration in the sound or intermittent skipping some tracks
during play.
• This unit has been designed to play compact discs
bearing the identification logo shown on the left.
Discs bearing other types of identification logos
may not play properly.
• Playback may not be possible due to the
characteristics of the CD recorder or the CD-R/RW
used, or due to scratches or dirt on the CD.
• For some CD-R/RWs, depending on the quality
of their recording or storage media used, playback
may not be possible due to deterioration of
recorded of material.
• Do not use non-conventional discs such as
heart-shaped, octagonal discs, etc.
The player could be damaged.
• Fingerprints and dust should be carefully wiped
from the signal surface of the disc (glossy side) with
a soft cloth.
Wipe in a straight motion from the inside to the
outside of the disc. Unlike conventional records,
the compact disc has no grooves to collect dust and
Label Side
debris. Small dust particles will have no effect on
reproduction quality.
• Do not insert a disc which is cracked into the unit.
• Do not apply paper or write anything on the disc.
• To prevent warping the disc, do not expose it to
direct sunlight, high humidity or high temperatures
for extended periods.
-3-
• Never use chemicals such as record cleaning
sprays, antistatic sprays or fluids, benzene or
thinner to clean compact discs. These chemicals
will permanently damage the plastic surface of
the disc.
• When not using the disc player for extended
periods, remove the compact disc and return it to
the plastic storage case. This will protect the disc
from dust and exposure to the sun.
Benzene Thinner Cleaning spray
• Mixed-mode CDs
This product can only play audio tracks on mixed-mode CDs.
The initial track contains non-audio data, and so it does not produce any sound.
Playback will start from the next track.
(Mixed-mode CDs are CDs which contain both non-audio data and audio tracks.)
• CDs containing copy control protection technology.
It is possible that some CDs with copy control protection (added to prevent computer
duplication) may not play on this unit.
This is due to the CD with copy control protection not conforming to CD standards and is
not due to a malfunction of this unit.
If there are any problems playing a CD with copy control protection, consult the store where
the CD was purchased.
-4-
REMOTE CONTROLLER
REMOTE CONTROLLER OPERATION
PRESET (+) Button
• Radio mode:
Not used
Select a registered station
• CD-CH mode:
DISC change
CD Button
BAND button
Change reception band
Change to CD mode
Switch between CD and
CD-CH when CD CHANGER
is connected
TAPE Button
Switch to TAPE mode
Switch DIRECTION
SCN button
• Radio mode:
Scan a preset station
• CD/CD-CH mode:
Play introduction to
current DISC
ATP Button
PWR Button
Power ON/OFF
• Radio mode:
Select a station
received by ATP
• TAPE mode:
AMSS switching
Select title using
• TAPE mode:
Play introduction
TUNE Button
• Radio mode:
TUNE (
) button
.
Short press:
TUNE Button
• Radio mode:
Short press:
Station selected manually
(to higher frequency )
Long press:
Station selected automatically
(to higher frequency )
• CD mode:
Station selected manually
(to low frequency station)
Long press:
Station selected automatically
(to low frequency station)
• CD mode:
Short press:
Rewind to a previous track
Long press: Fast rewind
• TAPE mode:
Short press:
Skip to the next track
Long press: Fast-forward
• TAPE mode:
Fast rewind
SHF Button
Tape fast-forward
• CD mode:
SHUFFLE current DISC
• CD-CH mode:
SHUFFLE current DISC
RPT Button
• CD mode:
REPEAT current title
• CD-CH mode:
REPEAT current title
• TAPE mode:
SOUND Button
SOUND EFFECT
switching mode
VOL(+/-) Button
Adjust volume
+: Volume up
REPEAT current title
JAZZ FLAT ROCK
-: Volume down
AUDIO Button
Sound quality modulation
switching mode
PRESET (-) Button
• Radio mode:
Select a registered station
• CD-CH mode:
DISP Button
Changeover of
clock display
BASS TREBLE
BALANCE
FADER
DISC change
Adjust using VOL button (+/-)
CAUTION
• For the purpose of safe driving, a passenger other than a driver should operate a remote
controller while the vehicle is being driven, or the operation should be done after parking the
vehicle in a safe area.
-5-
BATTERY INSTALLATION
Install a lithium battery (CR2025) with the poles facing the correct direction.
Positive pole faces upward.
BATTERY REPLACEMENT TIMING
When battery power is depleted, the buttons may not be operable.
If the remote controller does not operate, replace the battery and check the operation.
CAUTIONS REGARDING BATTERY
Be sure to follow the instructions to prevent battery leakage, over-heating, ignition, or explosion.
WARNING
• Do not expose the battery to flame. Do not short circuit, disassemble, or heat the battery.
• Do not charge the battery.
• Use the specified type battery.
• Keep the button-shaped battery away from children to prevent accidental swallowing.
• If the battery is swallowed, contact a doctor immediately.
CAUTION
• Install the battery with the poles facing the correct direction.
• When not in use for a long period of time, or if the battery is dead, remove the battery from
the remote controller.
If battery leakage has occurred, wipe the container first, then install a new battery. If the battery solution
contacts the skin, wash off with water completely.
CAUTIONS REGARDING REMOTE CONTROLLER
• Do not leave the remote controller in an area exposed to direct sunlight, such as on the dashboard or
steering wheel. The remote controller may deform because of the heat. (Be especially careful of the
dashboard exposed to direct sunlight in the summer, as it will become extremely hot.)
• When the vehicle is parked in an area exposed to direct sunlight, remove the remote controller from its
holder and put it in a shaded spot such as the glove box.
• Under direct sunlight, signal reception from the remote controller becomes weakens. If this happens, hold
the remote controller close to the signal receptor on the front panel.
-6-
DIGITAL DISPLAY
Repeat Play
Disc Number,
Preset Channel,
ATP Channel
BASS mode
Shuffle
Play
Sound mode
CD-CH
Disc in
Tape playing
direction
Radio Frequency, Time,
CD Track Number,
Error Signs,
AM Band
FM Bands
Metal
Play
Audio Control
Selection,
Scan Play
Auto Travel
no CD, no Tape,
Sound Mode Display
Automatic Music
Select System (AMSS)
Preset (ATP)
-7-
DETACHABLE FRONT PANEL
The front panel is designed to be removable for antitheft purposes.
It is recommended that you remove and carry the front panel with you when you leave your car.
A carrying case is provided with the unit for this purpose.
OPEN BUTTON
HOW TO DETACH THE FRONT PANEL
1
Press the open button to open the door.
2
Pull the right side of the panel, then pull the left side
of the panel to remove it from the unit.
FRONT PANEL
HOW TO REPLACE THE FRONT PANEL
Align the right side of the panel with the stopper, and then
push the left side of the panel into the unit until it clicks.
Note
The unit will not operate if it is installed incorrectly.
SCREW
SECURITY
To avoid theft or loss of the front panel, you can inactivate
the release knob by installing the screw provided as shown.
FRONT PANEL
CAUTION
• Do not attempt to remove the panel in a manner other than that described above.
• When installing the panel, do not force it into the unit.
• Do not touch the connection terminals of the panel or the unit. It may cause poor
contact.
• Use a clean, dry cloth when cleaning the terminals.
• Keep the panel out of direct sunlight and high temperatures.
• Prevent the panel from coming into contact with benzene, thinner, or insecticides.
• Do not drop the panel.
• Do not attempt to remove the radio front panel that takes your attention away from
safety driving you vehicle.
-8-
GENERAL OPERATION
3
4
1
5 7
2
6
TURNING THE POWER ON........................................ 1
Install the front panel and press the POWER button when ACC is on.
TURNING THE POWER OFF ...................................... 1
Press the POWER button to stop the current operation.
The button dims when the power is off (ACC on).
ELECTRONIC CONTROLS......................................... 2
Press the AUDIO button , then press the AUDIO button to select the audio functions as shown in the
table below.
Turn the VOL knob to adjust the selected function ; bass, treble, balance, fade, or volume.
Note
While no other mode is displayed, the VOL knob function as a volume control.
MODE
Turn left (Min) Turn right (Max)
Down -5
Down -5
UP
UP
+5
+5
bAS(bass)
TRE(treble)
bAL(balance)
FAd(fader)
Left
Rear R9
Down
L9
Right R9
Front F9
VOL(volume)
0
UP
35
SOUND EFFECT BUTTON ......................................... 3
Press the SOUND Button for less than 1.5 second.
Each time the button is pressed, the function changes as shown below.
3
1 FLAT
ROCK
2
JAZZ
-9-
BASS CONTROL.......................................................3
Press the SOUND button for more than 1.5 second to switch ON/OFF of the BASS mode. When the BASS
mode is on, “BASS” is displayed and the bass enhances.
RADIO SELECTION BUTTON (BAND) .........................4
Press the BAND button to switch from CD player, CD changer or tape mode to radio.
Each time the button is pressed, the function changes as shown below.
FMIII
FMI
FMII
AM
TAPE, CD PLAYER OR CD CHANGER* SELECTION
BUTTON (CD/TAPE/CD-CH) .......................................5
Press the CD/TAPE/ CD-CH button to switch from radio or tape mode to CD player or CD changer* mode.
*If a CD changer is connected.
Radio
CD player
CD changer
TAPE
Notes
• When a CD is not loaded in the CD player, the CD player mode is skipped.
• When a cassette is not loaded in the cassette player, the TAPE mode is skipped.
• When a CD changer is not connected, the CD changer mode is skipped.
CLOCK BUTTON (DISP) ............................................6
Press the DISP button to switch between the clock and audio display. When an audio function is
performed while the time display is selected, the audio display will appear for 5 seconds, then the display
will return to the time mode.
TO CANCEL THE BEEP TONES .................................1, 7
1
Turn off the power by depressing the POWER button
.
2
To cancel all beep tones, press the POWER button and the ATP button simultaneously for more
than 3 seconds and then "bP : OF" is displayed.
3
To turn on the beep tones again, perform the same procedure. The beep tones are set and "bP : on" is
displayed.
-10-
RADIO OPERATION
1
4
5
3
2
SELECTING RADIO MODE ........................................ 1
Press the BAND button to switch from CD player, CD changer or tape mode to the radio.
Each time the BAND button is pressed, the selected band changes as shown below.
FMIII
FMI
FMII
AM
RADIO TUNING ........................................................ 2
• Automatic tuning ............Press the > or < button for more than 0.5 second until it beeps twice if the beep
tones are on. When the button is released, the system will start automatic tuning
and stop at the next receivable station.
•
Manual tuning ................To select higher frequency stations, press the > button for less than 0.5
second.To select lower frequency stations, press the < button for less than 0.5
second. To quickly scan up or down in frequency, press and hold the > or <
button. Release the button when the display approaches the desired frequency,
then press and release the button repeatedly until the desired frequency is
displayed.
STORING PRESET STATIONS ................................... 3
The preset buttons can be used to store 6 stations in each band (FMI, FMII, FMIII and AM) for convenient
access to your favorite stations.
1
2
• Programming stations.....
Select the desired band, then tune in the station you want to store in memory.
Press and hold one of the preset buttons for more than 2 seconds.
1
2
Repeat steps
and
to program additional stations.
• Quick tuning.................... Select the desired band, then press one of the six preset buttons.
-11-
ATP (AUTO TRAVEL PRESET) OPERATION................4
The Auto Travel Preset function searches for and memorizes the 6 strongest stations in one of the two
bands (FM, AM) in the order of signal strength.
This feature is useful when you are driving in an unfamiliar location and want to memorize local stations
without changing the standard preset stations.
A total of 12 stations (6 FM and 6 AM) can be programmed.
1
2
•
To set the stations...............................
Select the desired band.
Press and hold the ATP button for more than 2 seconds.
“ATP” appears in the display.
When the stations have been memorized, scanning stops and the
strongest station is selected.
1
2
•
Quick Tuning of ATP Stations .................
Select the desired band.
Press the ATP button if the “ATP” indicator does not appear in
the display.
3
While ATP is illuminated, press the ATP button and the unit
seeks ATP1-6. If there is no preset ATP, - 0 - appears in the
display.
• To scan programmed stations............. See “PRESET-SCAN-BUTTON OPERATION”.
Notes
• If no station can be received, “- 0 -” appears in the display.
• If fewer than 6 stations can be received, the system will memorize as many stations as
possible, then select the strongest one.
• If ATP mode is selected in FMII band, FM ATP mode is selected.
To cancel the ATP, press the BAND button . When ATP is canceled, the ATP indicator disappears and
ATP mode is canceled.
PRESET-SCAN-BUTTON OPERATION ........................1, 4, 5
This function scans each of the preset stations stored in the selected band (both manual preset and
auto travel presets).
1
Select the desired band or ATP mode.
Press the BAND button for FMI, FMII, FMIII or AM. Press the ATP button to select the ATP mode.
2
3
Press the P.SCN button . The system will select and receive each preset station for five-second.
To stop scanning and retain the station currently selected, press the P.SCN button again during this
five-second period.
-12-
TAPE OPERATION
4
1
5 11
10
6
7
9 8
LOADING AND EJECTING THE TAPE......................... 1, 2, 3
Press the OPEN button to open the door.
Insert a cassette into the tape slot and the
tape player will start.
Press the eject button to eject a tape.
CAUTION
• Only cassette tapes that play no longer than 90 minutes should be used. Tapes exceeding 90 minutes
are thin and may easily break.
SELECTING TAPE MODE .......................................... 4
Inserting a cassette into the tape slot as start the tape player. If radio, CD player or CD changer* is in
operation with a tape loaded, press the TAPE button to switch to tape mode.
* If a CD changer is connected.
SWITCHING THE TAPE DIRECTION ........................... 5
Press the button
.
When the tape reaches the end of one side, the unit will automatically switch to the opposite side of the tape.
FAST FORWARD AND REWIND................................. 6, 7
Press the > button to fast forward and press the < button to rewind the tape.
Pressing the button during fast forward and rewind operation resumes tape playing.
-13-
LOCATING THE BEGINNING OF A PROGRAM
(AMSS) ....................................................................6, 7, 8
This system is equipped with a function that allows you to skip forward or backward to locate the beginning
of a particular selection on the tape. (Automatic Music Select System : AMSS)
1
2
Press the AMSS button . "AMSS" is displayed.
Press the > button to skip forward up to 9 selections from the current location on the tape.
e.g.) With "AMSS" displayed, press button three times. "F3" is displayed.
The system will search for 3 blank spaces between selections in the forward direction, then begin
playing the third selection from the starting point.
3
4
Press the < button to skip backward to the beginning of the current selection, or up to 8 selections
from the current location on the tape.
e.g.) With "AMSS" displayed, press button five times. "R5" is displayed.
The system will search for 5 blank spaces between selections in the backward direction, then begin
playing the forth selection from the starting point. (The blank space before the current selection
counts as one blank space.)
To cancel AMSS mode, press button again.
Notes
• If AMSS detects 15 seconds of blank space, it will automatically advance the tape
to the next selection.
• AMSS may not operate properly if
• A tape was recorded at a low level.
• A tape has long, silent intervals.
• A tape is a live recording.
METAL PLAY MODE .................................................9
If a metal or high-position tape is used, press the MTL button
is indicated.
to make the player in metal play mode. MTL
SCAN MODE ............................................................10
Scan helps to find a program by playing about the first 10 seconds of each selection.
Press the SCN button during play to start scan operation. "SCN" is displayed.
To cancel scan, press the SCN button again.
REPEAT MODE.........................................................11
This operation makes it possible to listen repeatedly to a selection.
Press the RPT button ⑪ during play. "RPT" is displayed, the selection playing will continue until RPT is
pressed again.
Notes
RPT/SCN may not operate properly if
• A tape was recorded at a low level.
• A tape has long, silent intervals.
• A tape is a live recording.
-14-
CD OPERATION
4
1
6
5
7 8
9
LOADING AND EJECTING THE CD ............................ 1, 2, 3
Press the OPEN button to open the door.
2
Insert a disc into the CD slot and the
CD player will start.
Press the eject button to eject a disc.
3
CAUTION
• This CD player is not designed for 8 cm CDs.
Please do not use an 8 cm CD nor 8 cm CD adaptor.
• If the unit is already loaded with a CD, please do not attempt to insert another disc,
which may result in damage to both of the discs and the unit.
Note
When the CD is ejected, "no" "Cd" will be flash alternately.
SWITCHING TO CD MODE......................................... 4
Press the CD / TAPE / CD-CH button to switch from radio or tape or CD changer* mode to CD player
mode.
When the CD mode is switched on while a disc is loaded, play resumes from the point at which play was
stopped.
When the entire disc has played, the unit returns to the first track and play resumes.
The CD player continues playing the disc until the POWER button is pressed, the other mode is selected, or
the disc is ejected.
* If a CD changer is connected.
-15-
SKIPPING TRACKS...................................................5, 6
Press the > button to skip to the beginning of the next track.
Press the < button to skip to the beginning of the track currently playing.
Press the < button twice to skip to the beginning of the previous track.
Press and hold the > or < button for more than 0.5 seconds to search quickly
(with sound) in the forward or reverse direction.
When the button is released, the CD resumes normal play.
SHUFFLE MODE.......................................................7
This function plays the tracks on a CD in random order.
Press the SHF button to begin shuffle play. The SHF indicator lights.
Press the > or < button to select another random track.
To cancel this mode, press the SHF button again or eject the CD.
Notes
If a disc is already loaded under the following conditions, shuffle play will resume
from the point at which play was stopped:
• If the vehicle ignition is turned off, then on again.
• If the power is switched off, then on again with the ON/OFF button.
REPEAT MODE.........................................................8
Press the RPT button to play the current track repeatedly. The RPT indicator lights.
To cancel this mode, press the RPT button again or eject the CD.
Notes
If a disc is already loaded under the following conditions, repeat play will resume:
• If the vehicle ignition is switched off, then on again.
• If the power is switched off, then on again with the ON/OFF button.
SCAN MODE (PLAYING THE BEGINNING
OF EACH TRACK).....................................................9
This function plays the first 10 seconds of each track sequentially.
Press the SCN button to begin the scan mode. The SCN indicator lights.
To cancel this mode, press the SCN button again.
Note
Scan mode will be canceled when the vehicle ignition is turned off, or when the disc
is ejected.
-16-
CD CHANGER OPERAON
THE UNIT CAN BE USED TO CONTROL THE FUNCS OF THE COMPATIBLE SANYO CD
CHANGERS. (If a CD changer switch is equipped, alwset it to "1".)
1
6 7
3
5
8
4
2
SELECTING CD CHANGER MODE .
Press the CD/TAPE/CD-CH button to switch fradi
SELECTING A DISC...............
Press the DISC + button to select the ne
Press the DISC - button to select the pc.
SKIPPING TRACKS ........
Press the > button to skip to the ext
Press the < button to skip to thack
Press the < button twice to sthe
Press and hold the > or < button
reverse direction.
When the button is releasepla
SHUFFLE MO..
This function plays tthe
•
“Shuffle-playing” tbu
•
“
Shuffle-playin
To canc
or ejec
The s
REPEAT MODE.........................................................7
•
Repeat tracks...................................... Press the RPT button to play the current track repeatedly.
The RPT indicator lights.
•
Repeat discs ......................................... Press the RPT button for more than 1.5 seconds to play the current
disc repeatedly. The RPT indicator blinks.
To cancel the track repeat or disc repeat mode, press the RPT button again, press the DISC + or - button
or eject the magazine.
The system will remain in this mode until it is cancelled.
SCAN MODE (PLAYING THE BEGINNING
OF TRACKS OR DISCS) ............................................8
This function plays the first 10 seconds of each track or disc sequentially.
•
•
Playing the beginning of tracks ........... Press the SCN button to play the first 10 seconds of each track on
the current disc in order. The SCN indicator lights.
Playing the beginning of discs............. Press the SCN button for more than 1.5 seconds to play the first 10
seconds of each disc in the magazine. The SCN indicator blinks.
To cancel the track scan or disc scan mode, press the SCN button again or press the DISC + or - button.
Note
Scan mode will be canceled when the vehicle ignition is turned off or when the magazine is
ejected.
-18-
ERROR SIGNS
CD Player
If a problem should occur while operating the built-in CD player, one of the following error signs
may be displayed:
Symptom
Cause
Solution
Press the eject button.
Turn the power off and then on
again. If it is not corrected, contact
the place of purchase.
E01
Abnormal CD mechanism function.
The disc was inserted incorrectly.
The disc is dirty.
Insert the disc properly.
Clean the disc.
E07
E99
The disc is defective.
Use another disc.
There is condensation on the opti-
cal lens.
Leave the disc player off for an hour
or so, then try again.
Turn the power off and then on
again.
If it is not corrected, contact the
place of purchase.
Internal connection check error.
CD Changer
If a problem should occur while operating the connected CD changer, one of the following error signs may
be displayed.
Symptom
Cause
Solution
Contact the place of purchase.
Insert the disc properly.
Clean the disc.
E01
Abnormal mechanism function
The disc was inserted incorrectly.
The disc is dirty.
The disc is defective.
Use another disc.
E07
There is condensation on the
optical lens.
Leave the disc player off for an hour
or so, then try again.
Refer to the instructions supplied
with the CD changer.
The magazine is not fully inserted
into the changer.
No discs in the magazine.
Completely insert the magazine into
the changer until it clicks into place.
Load discs into the magazine.
no Cd
-19-
CLOCK
1
3
2
4
DISPLAY MODE CHANGE..........................................1
The display on the unit can be changed by pressing DISP button . Press the DISP button to switch
between the clock and audio display. When a radio, tape and CD function is performed while the time display
is selected, the audio display will appear for 5 seconds, then the display will return to the time mode.
ADJUSTING THE TIME ..............................................1, 2, 3
To adjust the time, press the DISP button for more than 2 seconds. The time display blinks.
To adjust the minute, press the > button
To adjust the hour, press the < button
.
.
To advance the time rapidly, hold the > or < button continuously.
Press DISP button again to start the clock.
CLOCK RESET .........................................................1, 4
Press DISP button for more than 2 seconds and the time display blinks. While blinking, press preset
button 6 to skip to the nearest half-hour as follows:
Example: 3:00 – 3:29
3:00
4:00
3:30 – 3:59
-20-
HINTS FOR PROPER AND SAFE OPERATION
• Condensation
Moisture can condense on the optical lens of the CD player during humid or rainy days, or after the car
heater is turned on. If this occurs the disc player may not function properly. To remedy the situation,
remove the disc from the unit and wait approximately one hour. This should allow the moisture to
evaporate and restore normal operation.
• Temperature Consideration
The unit may not operate correctly in extremely hot or cold temperatures. Avoid exposing the unit to
extremely high or low temperatures.
• Interruptions in the sound (skipping)
When the car is driven on very rough surfaces, the sound from the CD player may skip and be interrupted.
This will not cause any damage to the disc or the player. If this occurs, wait for the road surface to
improve before using the CD player.
• Safety
For safer driving, keep the volume at a moderate level to enable you to hear outside sounds (such as
emergency vehicle sirens).
• Cleaning the unit
Clean the unit with a soft, dry cloth. Stains should be removed by wiping the surfaces with a soft cloth
immersed in lukewarm water and wrung dry. Never use strong chemicals or solvents. These will damage
the finish of the unit.
• Disc care
When not using the disc player for extended periods, remove the compact disc and return it to the
plastic storage case. Do not leave a disc partially ejected from the player.
• Servicing
Should a problem develop, do not open the unit or try to repair it yourself. If servicing is required, bring
the unit to a Sanyo Authorized Service Center.
-21-
TROUBLESHOOTING
Sometimes a simple operational error or a mistake in the wiring can appear to be a problem with the unit.
Before having the unit serviced, refer to the troubleshooting chart below.
Symptom
Cause
Solution
The compact disc does not play
when inserted into the unit.
The volume control is turned
down.
Turn up the volume control.
The power connections are not
wired correctly.
Check the +12V and ground
connections.
No sound is coming out.
No power.
The speaker code connection is
incomplete.
Check the connection of the
speaker code, and press the
ON/OFF button.
The vehicle ignition is switched
off.
Switch the ignition to the "ON"
or "ACC" position.
The fuse is blown.
Replace the fuse with another
15A fuse.
The unit does not work properly
(Eject, Load, Play).
The microcomputer has been
affected by electrical noise.
Eject the disc, then insert it
again.
The sound from the CD player
skips.
The road surface is rough.
Wait for the road surface to
improve before playing a disc.
The unit is not mounted
securely.
Install the unit securely.
The disc is defective.
Try another disc. If it plays
properly, the first disc may be
defective.
The disc is dirty.
Clean the disc as explained on
pages 3-4.
No radio reception.
The antenna cable is not
connected.
Insert the antenna cable firmly
into the antenna jack on the
unit.
The radio does not stop on any
stations when automatic tuning
is used.
The signals are weak.
Select a station using manual
tuning.
-22-
ACCESSORIES AND HARDWARE
Mounting Bracket
(Half Sleeve) x 1
Rear Strap
(Brace) x 1
Screw 5 x 14
x 1
Hex bolt M5 x 8
x1
Unlock Levers
x 2
Screw 2 x 6
x 2
Removable Trim Ring
x 1
INSTALLATION
1. BEFORE INSTALLATION
When mounting the unit in a car, keep the unit as level as possible.
If the unit must be mounted at an angle, due to the design of the
vehicle, make sure the unit does not tilt by more than 30°.
-23-
2. ISO MOUNTING WITH REMOVABLE TRIM RING
When mounting the unit into a DIN-standard cutout (182 × 53 mm) in the dashboard or
console, attach the provided Removable Trim Ring to the unit.
DASHBOARD OR CONSOLE
182 mm
AUDIO UNIT
53 mm
REMOVABLE TRIM RING
3. INSTALLATION PROCEDURES
DASHBOARD
OR CONSOLE
5 x 14
HEX BOLT
182 mm
53 mm
REAR STRAP
(BRACE)
REMOVABLE
TRIM RING
MOUNTING BRACKET
(HALF SLEEVE)
AUDIO UNIT
1. Insert the mounting bracket into the DIN-standard cutout (182 × 53 mm) in the dashboard or console.
2. Bend the mounting bracket stopper outward until the bracket fits snugly in the cutout.
3. Push the unit into the mounting bracket until it locks in place.
4. Secure the rear strap to the audio unit and vehicle dashboard.
-24-
4. Installation to TOYOTA/NISSAN Vehicles
Install the unit using the existing TOYOTA/NISSAN Mounting Bracket and Screws. Use mounting holes in
the unit chassis. "T" or "N" is engraved next to each mounting hole. Use "T" holes for Toyota vehicles and
"N" holes for Nissan vehicles.
TOYOTA/NISSAN
Mounting Bracket
Screw
CAUTION
ONLY USE M5 x 6 SCREW
(NOT INCLUDED WITH THIS
UNIT) AS ILLUSTRATED ABOVE.
USE OF ANY OTHER SCREW OR
HARDWARE MAY RESULT DAMAGE
TO HEAD UNIT.
Screw
-25-
UNIT REMOVAL
AUDIO UNIT
(A)
(B)
(A)
(B)
UNLOCK LEVERS
(C)
1. Press the open button to open the door.
2. Pull the right side of the front panel, then pull the left side of the panel to remove it from the unit.
3. Insert the unlock levers into the slots as illustrated in (A).
Note
The jagged side of the unlock lever should face outward.
4. Slide both levers outward as illustrated in (B) and pull to remove the audio unit as illustrated in (C).
-26-
ELECTRICAL CONNECTIONS
1. ANTENNA SOCKET
ANTENNA PLUG
4-speaker System
2-speaker System
(White)
(White/Black)
(Gray)
(White)
(White/Black)
(Gray)
(Gray/Black)
(Green)
(Green/Black)
(Violet)
(Violet/Black)
Front Left
Speaker
Left
Speaker
Right
Speaker
Front Right
Speaker
Rear Left
Speaker
Rear Right
Speaker
(Gray/Black)
(Green)
Do Not
Connect
Do Not
Connect
(Green/Black)
(Violet)
(Violet/Black)
2. +12V Constant Power Supply (Yellow)
3. +12V Accessory/Switched (Red)
4. Ground Wire (Black)
5. Power Antenna (Blue/Red)
6. Amplifier Turn On (Blue/White)
7. Sub-Woofer Code (Monaural)
CAUTION
• DO NOT connect any speaker wires to the metal body or chassis of the vehicle.
• DO NOT connect the speaker common (-) wires to each other.
• Connect each speaker wire directly to each speaker terminal.
• All speaker common (-) wires must remain floating.
• When wiring the amplifier for the sub-woofer, noise may occur depending on where the
ground (earth) terminal is installed.
1 Antenna socket
• Insert the plug from the antenna installed in your vehicle into this socket. (If your vehicle has a dual
antenna system, a dual antenna to single antenna cable adaptor may be required.)
2 +12V Constant Power Supply (Yellow)
• Connect this wire to the +12V power terminal which receives power continuously.
3•+C12oVnnAeccct etossloocrayt/iSonwditrcahweindg(R10edA) amperage or more.
• Connect this wire to the terminal which receives power while the ignition switch is at ON or
ACCESSORY position.
• If the ignition switch does not have an ACC position, connect this wire to a +12V
power terminal which receives power continuously. (Same as item 2.)
4•GCroounnnedcwt tiorelo(cBaltaiocnk)drawing 100 mA amperage or more.
5•PCoownenreActnttheinsnwair(eBtloueth/Reevde)hicle chassis.
• Connect this wire to the control terminal of a Power Antenna.
6•AWmhpelinfienrotTuusrinngOanP(Bowlueer/WAnhtieten)na, this wire is not connected.
• Connect this wire to an external amplifier.
7•SWubh-eWnonoofteursCinogrdan(Mexotnearnuarlaal)mplifier, this wire is not connected.
• Connect this wire to an external sub-woofer amplifier.
• When not using an external sub-woofer amplifier, this wire is not connected.
-27-
Notes
• When using a two-speaker installation, the Green, Green/Black, Violet, Violet/Black wires,
which are used for a four-speaker installation, are not used. The ends of these wires must
be covered with electrical tape to prevent them from shorting to the unit or the vehicle chassis.
• When using a two-speaker installation, set the
FADER control to the center position.
• When fuse replacement is necessary remove
the blown fuse by using pliers.
Then install the new 15 amp. fuse.
Fuse 15A
NG
OK
Burnt
LINE OUT/CD CHANGER CONNECTIONS
• The unit has a built-in CD changer controller and line output terminals. You can use a compatible Sanyo
CD changer and a separate amplifier to upgrade your system.
RCA Line-out Jacks
OUTPUT
FRONT REAR
White
L (eft)
CD Changer
DIN Socket
R (ight)
Red
External
Amplifier
CD Changer
Rear Speaker
Front Speaker
CD Changer DIN Socket
• Connect the 8-pin DIN cable, which is supplied with the compatible Sanyo CD changer, to the DIN socket
on the back of the unit.
RCA Line-out Jacks (For Speakers)
• Connect a patch cable (not supplied) from the White (left channel) and Red (right channel) RCA line output
jacks to the line input terminals of the external amplifier.
-28-
SPECIFICATION
FM TUNER SECTION
Frequency Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87.5MHz–107.9MHz
Usable Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15dBf
50dB Quieting Sensitivity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30dBf
Frequency Response ( 3dB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50Hz–12.5kHz
I.F. Rejection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100dB
Image Rejection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65dB
Signal-to-Noise Ratio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60dB
Selectivity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65dB
Stereo Separation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27dB
Capture Ratio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2dB
Antenna Impedance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75Ω
AM TUNER SECTION
Frequency Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 530kHz–1710kHz
Usable Sensitivity (S/N 20dB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20µV
I.F. Rejection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80dB
Image Rejection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75dB
S/N Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50dB
Antenna Impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75Ω
TAPE SECTION
Wow and Flutter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.1%
S/N Ratio (Normal) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52dB
Separation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50dB
Frequency Response. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50Hz–15kHz
CD SECTION
Disc size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5”
Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-channel stereo
Sampling Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44.1kHz
D/A Converter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Twin, 1–bit
Pickup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Optical 3-beam semiconductor laser
Digital Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 fs
Frequency Response. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20Hz–20kHz
Total Harmonic Distortion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.1% (1 kHz)
Dynamic Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85dB
Signal-to-Noise Ratio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90dB
Wow and Flutter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Below measurable limits
Channel Separation (1kHz) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85dB
AUDIO SECTION
RMS Power Rating (3% THD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20W × 4 (14.4 V)
RMS Power Rating (10% THD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24W × 4 (14.4 V)
Maximum Output Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50W × 4CH (15.5 V)
Load Impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Ω
GENERAL
Operating Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12V (10.5–15.5 V)
Operating Current Maximum . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13A
IMPORTANT INFORMATION
Because its products are subject to continuous improvement, SANYO reserves the right to modify
product designs and specifications without notice and without incurring any obligation.
-29-
21605 Plummer Street
Chatsworth, CA91311
1ED6P10A18800
Rev.0
Printed in Malaysia
|