BD-C6800
Blu-ray Disc Player
user manual
imagine the possibilities
Thank you for purchasing this Samsung product.
To receive more complete service,
please register your product at
Safety Information
Warning
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER (OR BACK).
NO USER-SERVICEABLE PARTS ARE INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lighting flash and Arrowhead within the CAUTION: TO REDUCE THE RISK OF ELECTRIC The explanation point within the triangle
triangle is a warning sign alerting you of
dangerous voltage inside the product.
SHOCK, DO NOT REMOVE COVER (OR BACK)
is a warning sign alerting you of important
NO USER SERVICEABLE PARTS INSIDE. REFER instructions accompanying the product.
SERVICING TO QUALIFIED SERVICE PERSONNEL.
WARNING
FCC RF Radiation Exposure
•
To reduce the risk of fire or electric shock, do
RF Radiation Exposure Statement
not expose this appliance to rain or moisture.
This equipment complies with FCC RF Radiation
Exposure limits set forth for an uncontrolled
environment. This equipment should be installed
and operated with a minimum distance of
FCC NOTE (for U.S.A)
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC rules. These limits
are designed to provide reasonable protection
against harmful interference in a residential
installation. This equipment generates, uses
and can radiate radio frequency energy and, if
not installed and used in accordance with the
instructions, may cause harmful interference
to radio or television reception, which can be
determined by turning the equipment off and on.
20cm between the radiator and your body. This
transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference,
and
(2) This device must accept any interference
received, including interference that may cause
undesired operation.
The user is encouraged to try to correct the
interference by one or more of the following
measures.
Changes or modifications not expressly approved
by the party responsible for compliance could void
the user’s authority to operate the equipment.
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment
and receiver.
To comply with the FCC RF exposure compliance
requirements, this device and its antenna must
not be co-located or operated in conjunction with
any other antenna or transmitter.
•
Connect this equipment into an outlet on a
circuit different from that to which the receiver is
connected.
•
•
Consult the dealer or an experienced radio/TV
technician for help.
The final device into which this transmitter module
is installed must be labeled with the following
statement:
This class B digital product meets all
requirements of the Canadian Interference -
Causing Equipment Regulations.
“This device contains TX FCC ID: A3LDNUBS1.”
If this transmitter will be configured as a pc
peripheral, it will be the OEM’s responsibility
to obtain authorization as such (either through
Certification of Declaration of Conformity) prior to
marketing of the device.
English
ꢁ
Safety Information
This reminder is provided to call CATV system
installer’s attention to Article 820-40 of the
National Electrical Code (Section 54 of Canadian
Electrical Code, Part I) that provides guidelines
for proper grounding and, in particular, specifies
that the cable ground shall be connected to the
grounding system of the building as close to the
point of cable entry as practical.
Note to CATV system installer
Precautions
Important Safety Instructions
Read these operating instructions carefully before
using the unit. Follow all the safety instructions
listed below.
Keep these operating instructions handy for future
reference.
CLASS 1 LASER PRODUCT
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
This Compact Disc player is classified as a CLASS
1 LASER product. Use of controls, adjustments
or performance of procedures other than those
specified herein may result in hazardous radiation
exposure.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
Complies with 21CFR 1040.10 except for
deviations pursuant to Laser Notice No. 50, dated
June 24, 2007.
7. Do not block any ventilation openings. Install
in accordance with the manufacturer’s
instructions.
DANGER :
•
VISIBLE AND INVISIBLE LASER RADIATION
WHEN OPEN. AVOID DIRECT EXPOSURE TO
BEAM. (FDA 21 CFR)
8. Do not install near any heat sources such
as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce
heat.
CAUTION :
•
•
CLASS 3B VISIBLE AND INVISIBLE LASER
RADIATION WHEN OPEN. AVOID EXPOSURE
TO THE BEAM (IEC 60825-1)
9. Do not defeat the safety purpose of the
polarized or grounding-type plug. A polarized
plug has two blades with one wider than the
other. A grounding type plug has two blades
and a third grounding prong. The wide blade
or the third prong are provided for your safety.
If the provided plug does not fit into your
outlet, consult an electrician for replacement
of the obsolete outlet.
THIS PRODUCT UTILIZES A LASER. USE
OF CONTROLS OR ADJUSTMENTS OR
PERFORMANCE OF PROCEDURES OTHER
THAN THOSE SPECIFIED HEREIN MAY
RESULT IN HAZARDOUS RADIATION
EXPOSURE. DO NOT OPEN COVER AND DO
NOT REPAIR YOURSELF. REFER SERVICING
TO QUALIFIED PERSONNEL.
10. Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where they exit
from the apparatus.
CLASS 1
KLASSE 1
LUOKAN 1
KLASS 1
LASER PRODUCT
LASER PRODUKT
LASER LAITE
11. Only use attachments/accessories specified
LASER APPARAT
by the manufacturer.
PRODUCTO LÁSER CLASE 1
12. Use only with the cart,
stand, tripod, bracket,
NOTE
✎
or table specified by the
If the Region number of a Blu-ray Disc/DVD disc
does not correspond to the Region number of this
player, the player cannot play the disc.
▪
manufacturer, or sold with
the apparatus. When a cart
is used, use caution when
moving the cart/apparatus combination to
avoid injury from tip-over.
ꢂ
English
13. Unplug this apparatus during lightning storms
•
If you move your player suddenly from a cold
place to a warm place, condensation may
generate on the operating parts and lens and
cause abnormal disc playback. If this occurs,
wait for two hours before connecting the plug to
the power outlet.
or when unused for long periods of time.
14. Refer all servicing to qualified service
personnel. Servicing is required when the
apparatus has been damaged in any way,
such as power-supply cord or plug is
Then insert the disc and try to play back again.
damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does
not operate normally, or has been dropped.
Handling Cautions
•
•
Do not write on the printed side with a ball-point
pen or pencil.
Disc Storage & Management
Do not use record cleaning sprays or antistatic.
Also, do not use volatile chemicals, such as
benzene or thinner.
Disc Handling
•
Do not apply labels or stickers to discs. (Do not
use discs fixed with exposed tape adhesive or
leftover peeled-off stickers.)
Disc Shape
•
Use discs with regular
•
•
Do not use scratch-proof protectors or covers.
shapes. If an irregular disc
(a disc with a special shape)
is used, this player may be damaged.
Do not use discs printed with label printers
available on the market.
•
•
Do not load warped or cracked discs.
Before connecting other components to this
player, be sure to turn them all off.
Holding discs
•
Avoid touching the surface of a
•
Do not move the player while a disc is being
played as the disc may be scratched or broken,
or the player’s internal parts may be damaged.
disc where recording is performed.
Blu-ray Discs
•
•
•
•
Do not put a flower vase filled with water or any
small metal objects on the player.
•
If the player is not used for a long period of time,
remove the Blu-ray Disc from the player and
store it in its case.
Be careful not to put your hand into the disc
tray.
•
Be careful not to leave fingerprints or scratches
Do not place anything other than the disc in the
disc tray.
on the surface of the Blu-ray Disc.
DVD-VIDEO, Audio CD (CD-DA)
Exterior interferences such as lightning and
static electricity can affect the normal operation
of this player. If this occurs, turn the player
off and on again with the POWER button, or
disconnect and then reconnect the AC power
cord to the AC power outlet. The player will
operate normally.
•
Wipe off dirt or contamination on the disc with a
soft cloth.
Disc Storage
Be careful not to damage the disc because the
data on these discs is highly vulnerable to the
environment.
•
•
Be sure to remove the disc and turn off the
player after use.
•
•
•
•
Do not keep under direct sunlight.
Keep in a cool ventilated area.
Store vertically.
Disconnect the AC power cord from the AC
outlet when you don’t intend to use the player
for long periods of time.
Keep in a clean protection jacket.
English
ꢃ
Safety Information
•
To clean a disc, wipe it in a straight
line from the inside to the outside of
the disc.
•
•
Do not expose the player to any
liquid.
When the AC plug is connected to a wall outlet,
the player will still draw power (standby mode)
when it is turned off.
•
•
Apparatus shall not be exposed to dripping or
splashing and no objects filled with liquids, such
as vases, shall be placed on the apparatus.
The main plug is used as a disconnect device
and shall stay readily operable at any time.
Maintenance of Cabinet
For safety reasons, be sure to disconnect the AC
power cord from the AC outlet.
•
•
Do not use benzene, thinner, or other solvents
for cleaning.
Wipe the cabinet with a soft cloth.
Restrictions on Playback
•
This player may not respond to all operating
commands because some Blu-ray, DVD and
CD discs allow specific or limited operation and
features during playback.
Please note that this is not a defect in the
player.
•
Samsung cannot assure that this player will
play every disc bearing the Blu-ray Disc, DVD
or CD logo because disc formats evolve, and
problems and errors may occur during the
creation of Blu-ray Disc, DVD, CD software
and/or the manufacture of discs.
Please contact the SAMSUNG customer care
center if you have questions or encounter
difficulty in playing Blu-ray, DVD, or CD discs
in this player. Also, refer to rest of this user
manual for additional information on playback
restrictions.
ꢄ
English
Contents
2
2
Blu-ray Disc Features
KEy FEATURES
Blu-ray Disc Player Features
3
4
4
5
5
Warning
SAFETy INFORMATION
Precautions
Important Safety Instructions
Disc Storage & Management
Disc Handling
11 Before using the User Manual
GETTING STARTED
11
11
12
12
14
14
15
Disc Types and Contents that can be played.
Disc types that cannot be played
Blu-ray Disc Compatibility
Disc Types
Region Code
Copyright
Logos of Discs that can be played
15 Accessories
16 Front Panel
17 Front Panel Display
18 Rear Panel
19 Remote Control
19
20
20
Tour of the Remote Control
Setting the Remote Control
Controllable TV Codes
21 Connecting to a TV
CONNECTIONS
21
22
23
24
Case 1 : Connecting to a TV with an HDMI Cable
- Best Quality (Recommended)
Case 2 : Connecting to a TV with DVI Cable
- Best Quality (Recommended)
Case 3 : Connecting to a TV (Component)
- Better Quality
Case 4 : Connecting to a TV (Video)
- Good Quality
English
ꢅ
Contents
25 Connecting to an Audio System
CONNECTIONS
25
Case 1 : Connecting to an Audio System
(HDMI Supported Amplifier) - Best Quality
(Recommended)
26
27
27
Case 2 : Connecting to an Audio System
(7.1 Channel Amplifier) - Better Quality
Case 3 : Connecting to an Audio System
(Dolby Digital, DTS Amplifier) - Better Quality
Case 4 : Connecting to an Audio System
(2 Channel Amplifier) - Good Quality
28 Connecting to the Network
28
29
Cable Network
Wireless Network
30 Before Starting (Initial Settings)
31 Setting the Menu
32 Display
SETUP
32
33
33
33
35
35
35
35
35
3D
TV Aspect
BD Wise (Samsung Players only)
Resolution
HDMI Format
Movie Frame (24Fs)
Progressive Mode
Still Mode
HDMI Deep Color
35 Audio
35
36
37
37
37
37
Digital Output
PCM Downsampling
Dynamic Range Control
Downmixing Mode
DTS Neo:6
Speaker Setting
38 System
38
38
38
38
39
39
39
Initial Settings
Internet@TV Screen Size
Anynet+(HDMI-CEC)
BD Data Management
Clock
DivX(R) Registration
DivX(R) Deactivation
ꢆ
English
39 Network
SETUP
39
43
43
Network Settings
Network Status
BD-LIVE Internet Connection
43 Language
43 Security
43
44
Parental Rating
Change Password
44 General
44
44
44
44
Background
Energy Saving
Front Display
Power On/Off Sound
45 Support
45
45
Software Upgrade
Contact Samsung
46 Playing a Disc
BASIC FUNCTIONS
46
46
Playback
Disc Structure
46 Using the Disc menu/Title menu/Popup menu
46
46
46
47
Using the Disc Menu
Using the Title Menu
Playing the Title List
Using the Popup Menu
47 Using the Search and Skip Functions
47
47
Searching for a Desired Scene
Skipping Chapters
47 Slow Motion Play/Step Motion Play
47
47
Slow Motion Play
Step Motion Play
48 Repeat Playback
48
48
Repeat the Title or Chapter
Repeat the Section
48 Using the TOOLS button
48
49
49
49
49
50
Moving to a Desired Scene Directly
Selecting the Audio Language
Selecting the Subtitle Language
Changing the Camera Angle
Selecting the Picture Setting
Setting BONUSVIEW
English
ꢇ
Contents
50 Listening to Music
BASIC FUNCTIONS
50
Buttons on the Remote Control used for Music
Playback
51
51
51
Playing an Audio CD (CD-DA)/MP3
Repeat an Audio CD (CD-DA)/MP3
Playlist
52 Playing back a Picture
52
52
Playing a JPEG Disc
Using the TOOLS button
53 Playing back a USB Storage Device
54
Notes on USB connection
55 Using Internet@TV
NETWORK SERvICES
55
57
58
Getting Started with Internet@TV
Settings
Samsung Apps
59 BD-LIVE™
59 Software Upgrade Notification
59 Using the AllShare Function
61 Troubleshooting
64 Index
APPENDIx
65 Specifications
66
66
67
68
Compliance and Compatibility Notice
Copy Protection
Network Service Disclaimer
License
10
English
Getting Started
Before using the User Manual
Disc Types and Contents that can be played.
Term
Logo
Icon
Definition
BD-ROM
This involves a function available on a BD-ROM.
h
�
Z
BD-RE/-R
This involves a function available on a BD-RE/-R disc recorded in the BD-RE format.
This involves a function available on a DVD-VIDEO.
DVD-VIDEO
DVD-RW(V)
DVD-R
DVD+RW
This involves a function available on recorded DVD+RW or DVD-RW(V)/DVD-R/+R
discs that have been recorded and finalized.
�
DVD+R
Audio CD
This involves a function available on an audio CD-RW/-R (CD-DA format).
o
�
G
MP3
This involves a function available in a CD-RW/-R, DVD-RW/-R, BD-RE/-R disc or a
-
-
WMA
USB storage media containing MP3 or WMA contents.
This involves a function available in a CD-RW/-R, DVD-RW/-R, BD-RE/-R disc or a
USB storage media containing JPEG contents.
JPEG
DivX
MKV
MP4
This involves a function available in a CD-RW/-R, DVD-RW/-R, BD-RE/-R disc or a
USB storage media containing DivX, MKV, MP4 contents.
-
�
NOTE
✎
The player may not play certain CD-RW/-R and DVD-R due to the disc type or recording conditions.
If a DVD-RW/-R disc has not been recorded properly in DVD video format, it will not be playable.
▪
▪
▪
If contents which are consisting of more than 10 Mbps bit-rate have been recorded in DVD-R, it is not supported.
If contents which are consisting of more than 30 Mbps bit-rate have been recorded in BD-R or USB, it is not supported.
Disc types that cannot be played
•
•
HD DVD
•
•
DVD-RAM
•
•
DVD-RW(VR mode)
•
3.9 GB DVD-R Disc for
Authoring.
DVD-ROM/PD/MV-
Disc, etc
Super Audio CD
(except CD layer)
CVD/CD-ROM/CDV/
CD-G/CD-I/LD
(CD-Gs play audio only,
not graphics.)
English
11
Getting Started
NOTE
✎
Disc Types
Some commercial discs and DVD discs purchased
outside your region may not be playable with this
player. When these discs are played, either “This
disc can not be played.” or “Cannot read this disc.
Please check the regional code of the disc.” will be
displayed.
▪
BD-ROM
This Blu-ray disc can only be played back.
This player can play back pre-recorded
commercial BD-ROM discs.
Playback may not work for some types of discs, or
when specific operations, such as angle change and
aspect ratio adjustment, are being performed.
Information about the discs is written in detail on the
disc box. Please refer to this if necessary.
▪
▪
BD-RE/-R
This Blu-ray disc can be recorded and played
back.
This player can play back a BD-RE/-R disc
recorded by other compatible Blu-ray disc
recorders.
Do not allow the disc to become dirty or scratched.
Fingerprints, dirt, dust, scratches or deposits of
cigarette smoke on the recording surface may make
it impossible to use the disc for playback.
DVD-VIDEO
Discs with PAL programs recorded on them cannot
▪
▪
▪
•
This player can play back pre-recorded
commercial DVD discs (DVD-VIDEO discs) with
movies.
be played using this player.
This player is compatible with the NTSC color system
only.
•
When switching from the first layer to the
second layer of a dual-layered DVD-VIDEO disc,
there may be momentary distortion in the image
and sound. This is not a malfunction of the
player.
When a BD-J title is played, loading may take longer
than a normal title, or some functions may perform
slowly.
This player may not respond to all operating
commands because some Blu-ray, DVD and CD
discs allow specific or limited operation and features
during playback.
▪
DVD-RW
This player can play back a DVD-RW disc
recorded and finalized with a DVD video recorder.
Ability to play back may depend on recording
conditions.
Please note that this is not a defect in the player.
Samsung cannot assure that this player will play
every disc bearing the Blu-ray Disc, DVD or CD logo
because disc formats evolve, and problems and
errors may occur during the creation of Blu-ray Disc,
DVD, CD software and/or the manufacture of discs.
Please contact the SAMSUNG customer care center
if you have questions or encounter difficulty when
playing Blu-ray, DVD, or CD discs in this player.
Also, refer to rest of this user manual for additional
information on playback restrictions.
▪
DVD-R
This player can play back a DVD-R disc recorded
and finalized with a DVD Video recorder. Ability to
play back may depend on recording conditions.
DVD+RW
•
This player can play back a DVD+RW disc
recorded with a DVD Video recorder. Ability to
play back may depend on recording conditions.
Blu-ray Disc Compatibility
Blu-ray Disc is a new and evolving format.
Accordingly, disc compatibility issues are possible.
Not all discs are compatible and not every disc will
play back. For additional information, refer to the
Compliance and Compatibility Notice section of
this user manual.
1ꢀ
English
DVD+R
AVCHD (Advanced Video Codec High
Definition)
•
This player can play back a DVD+R disc
recorded and finalized with a DVD Video
recorder. Ability to play back may depend on
recording conditions.
•
This player can playback AVCHD format discs.
These discs are normally recorded and used in
camcorders.
•
•
The AVCHD format is a high definition digital
video camera format.
Audio CD (CD-DA)
The MPEG-4 AVC/H.264 format is capable of
compressing images at higher efficiency than
that of the conventional image compressing
format.
•
•
This player can play back CD-DA format audio
CD-RW/-R discs.
The player may not be able to play some
CD-RW/-R discs due to the condition of the
recording.
•
•
Some AVCHD discs use the “x.v.Color” format.
This player can playback AVCHD discs using
“x.v.Color” format.
CD-RW/-R
•
•
“x.v.Color” is a trademark of Sony Corporation.
•
Use a 700MB(80 minutes) CD-RW/-R disc.
If possible, do not use a 800MB(90 minutes) or
above disc, as the disc may not play back.
“AVCHD” and the AVCHD logo are trademarks
of Matsushita Electronic Industrial Co., Ltd. and
Sony Corporation.
•
If the CD-RW/-R disc was not recorded as a
closed session, you may experience delays
when playing back the beginning of the disc or
all recorded files may not play.
NOTE
✎
Some AVCHD format discs may not play, depending
on the recording condition.
▪
•
Some CD-RW/-R discs may not be playable
with this player, depending on the device which
was used to burn them. For contents recorded
on CD-RW/-R media from CDs for your
personal use, playability may vary depending on
contents and discs.
AVCHD format discs need to be finalized.
“x.v.Color” offers a wider color range than normal
▪
▪
DVD camcorder discs.
Some DivX, MKV and MP4 format discs may not
play, depending on the video resolution and frame
rate condition.
English
1ꢁ
Getting Started
Region Code
Copyright
Both the player and the discs are coded by region.
These regional codes must match in order to play
the disc. If the codes do not match, the disc will
not play.
© 2010 Samsung Electronics Co.,Ltd.
All rights reserved; No part or whole of this user’s
manual may be reproduced or copied without the
prior written permission of Samsung Electronics
Co.,Ltd.
The Region Number for this player is described on
the rear panel of the player.
Region
Disc Type
Blu-ray
Area
Code
North America, Central America,
South America, Korea, Japan,
Taiwan, Hong Kong and South
East Asia.
A
Europe, Greenland, French
territories, Middle East, Africa,
Australia and New Zealand.
B
India, China, Russia, Central
and South Asia.
C
1
2
3
The U.S., U.S. territories and
Canada
Europe, Japan, the Middle East,
Egypt, South Africa, Greenland
Taiwan, Korea, the Philippines,
Indonesia, Hong Kong
Mexico, South America,
Central America, Australia,
New Zealand, Pacific Islands,
Caribbean
DVD-VIDEO
4
Russia, Eastern Europe, India,
most of Africa, North Korea,
Mongolia
5
6
China
1ꢂ
English
Logos of Discs that can be played
Blu-ray Disc
3D Blu-ray Disc
DTS-HD Master Audio
DivX
Java
NTSC broadcast system in
BD-LIVE
Dolby TrueHD
U.S.A, Canada, Korea, Japan
Accessories
Check for the supplied accessories below.
TV
POWER
POWER
BONUSVIEW
SOURCE
SUBTITLE
AUDIO
DISC MENU
TOOLS
MENU
TITLE MENU
POPUP
Audio/Video cable
(AC39-00073A)
Batteries for Remote Control (AAA Size)
(AC43-12002H)
INFO
RETURN
EXIT
INTERNET@ FULL SCREEN REPEAT
79
MUTE
VOL
CH
AK59-00104R
User Manual
Quick Guide
Remote Control
(AK59-00104R)
(AK68-01963N)
(AK68-01855T)
English
1ꢃ
Getting Started
Front Panel
a
b c
def g
h
DISC TRAY
Opens to accept a disc.
1
REMOTE CONTROL SENSOR Detects signals from the remote control.
2
3
4
5
6
7
DISPLAY
Displays the playing status, time, etc.
Opens and closes the disc tray.
Stops disc playback.
OPEN/CLOSE BUTTON
STOP BUTTON
PLAY/PAUSE BUTTON
POWER BUTTON
Plays a disc or pauses playback.
Turns the player on and off.
A USB memory flash stick can be connected here and used as storage when
connected to BD-LIVE. It can also be used for software upgrades and MP3/JPEG/
DivX/MKV/MP4 playback.
USB HOST
8
NOTE
✎
Software upgrades using the USB Host jack must be performed with a USB memory flash stick only.
In disc menu of BD title, it does not operate play action by front panel's PLAY button.
▪
▪
1ꢄ
English
Front Panel Display
a
b
c
IN DISC INDICATOR
Lights when a disc is inserted or played back.
Displays the play time and the current status.
Lights when the wireless network is connected.
1
2
3
CURRENT TIME AND
STATUS INDICATOR
WIFI INDICATOR
English
1ꢅ
Getting Started
Rear Panel
a b c
d
e
g f
Can be used for network based services (See pages 55~60), BD-LIVE and software
upgrades using a network connection.
LAN
1
2
Using an HDMI cable, connect this HDMI output terminal to the HDMI input terminal
on your TV for the best quality picture or to your Receiver for the best quality sound.
HDMI OUT
DIGITAL AUDIO OUT
COMPONENT OUT
Connects to a Receiver.
3
Connects to equipment having component video input.
4
5
Connect to a 7.1CH analog input on an A/V amplifier.
(When connecting to a 5.1CH home theater or receiver, connect all the Analog
Audio output jacks from this product except for the Surround Back Left/Surround
Back Right outputs)
7.1CH ANALOG AUDIO OUT
VIDEO OUT
AUDIO OUT
Connects the input of external equipment using a video cable.
6
Connects to the audio input of external equipment using audio cables.
7
1ꢆ
English
Remote Control
Tour of the Remote Control
TV
POWER
POWER
Turn the player on and off.
Turn the TV on and off.
(To operate your TV, please refer to page 20)
To open and close the disc tray.
BONUSVIEW
SOURCE
After setup, allows you to set the input
source on your TV.
Press this to use Bonusview function.
Press numeric buttons to operate options.
SUBTITLE
AUDIO
Use this to access various audio functions
on a disc (Blu-ray Disc/DVD).
Press this to switch the Blu-ray Disc/DVD’s
subtitle language.
Press to skip backwards or forwards.
Press to search a disc backwards or
forwards.
Press to stop a disc.
Use this to enter the disc menu.
Press to pause a disc.
Press to play a disc.
DISC MENU
TOOLS
MENU
TITLE MENU
POPUP
Use this to enter the popup menu/title
menu.
Press this to move to the home menu.
Press this to use Tools menu.
INFO
Use this to display the playback information
during playing a Blu-ray/DVD disc.
Select menu items and change menu value.
RETURN
EXIT
Return to the previous menu.
Press this to exit the menu.
These buttons are used both for menus
on the player and also several Blu-ray Disc
functions.
Press this to link to various Internet@TV
services.
INTERNET@ FULL SCREEN REPEAT
Press this to see the full screen on a TV.
79
Allows you to repeat a title, chapter, track
or disc.
MUTE
VOL
CH
TV volume adjustment.
AK59-00104R
Use this to select a TV program.
Mutes the speakers of your TV.
Installing batteries
NOTE
✎
If the remote does not operate properly :
▪
•
•
•
•
Check the polarity +/– of the batteries (Dry-Cell)
Check if the batteries are drained.
Check if remote sensor is blocked by obstacles.
Check if there is any fluorescent lighting nearby.
English
1ꢇ
Getting Started
Setting the Remote Control
Controllable TV Codes
You can control certain functions of your TV with
Brand
SAMSUNG
AIWA
Code
Brand
NOBLEX
NOKIA
Code
TV POWER+66
TV POWER+74
this remote control.
TV POWER+01, +02,
+03, +04, +05,
Button
Function
+06, +07, +08, +09
TV POWER+72, +73,
TV POWER
Used to switch the television on and off.
NORDMENDE
PANASONIC
PHILIPS
+75
TV POWER+82
Used to select an external source
TV POWER+53, +54,
+74, +75
TV SOURCE
TV POWER+10, +11,
connected to the TV.
ANAM
+12, +13, +14,
+15, +16, +17, +18
TV POWER+06, +55,
TV VOL (+/–) Used to adjust the volume of the television.
+56, +57
BANG & OLUFSEN TV POWER+57
TV CH (
/
)
Used to select the desired channel.
Used to toggle the sound on and off.
, .
TV POWER+06, +56,
+57
PHONOLA
PIONEER
BLAUPUNKT
BRANDT
BRIONVEGA
CGE
TV POWER+71
TV POWER+73
TV POWER+57
TV POWER+52
TV MUTE
TV POWER+58, +59,
+73, +74
NOTE
✎
RADIOLA
TV POWER+06, +56
The functions listed above will not necessarily work
on all televisions. If you encounter problems, operate
the television directly.
▪
CONTINENTAL
RADIOMARELLI TV POWER+57
TV POWER+75
EDISON
RCA
REX
TV POWER+45, +46
TV POWER+74
TV POWER+19, +20,
+23, +24, +25,
+26, +27, +28,
+29, +30, +31,
+32, +33, +34
DAEWOO
To determine whether your television is
TV POWER+57, +72,
SABA
SALORA
SANYO
+73, +74, +75
compatible, follow the instructions below.
EMERSON
FERGUSON
TV POWER+64
TV POWER+73
TV POWER+74
1. Switch your television on.
TV POWER+41, +42,
2. Point the remote control towards the
TV POWER+06, +49,
FINLUX
+43, +44, +48
+57
television.
FORMENTI
FUJITSU
TV POWER+57
TV POWER+84
TV POWER+70
SCHNEIDER
SELECO
TV POWER+06
TV POWER+74
3. Press and hold the TV POWER button and
enter the two-figure code corresponding to
the brand of your television by pressing the
appropriate number buttons.
GRADIENTE
TV POWER+36, +37,
SHARP
+38, +39, +48
TV POWER+49, +52,
GRUNDIG
+71
If your television is compatible with the remote
control, it will switch off.
SIEMENS
SINGER
SINUDYNE
SONY
TELEAVA
TV POWER+71
TV POWER+57
TV POWER+57
TV POWER+35, +48
TV POWER+73
TV POWER+60, +72,
+73, +75
HITACHI
It is now programmed to operate with the
IMPERIAL
JVC
TV POWER+52
remote control.
TV POWER+61, +79
NOTE
✎
TV POWER+06, +19,
LG
+20, +21, +22, +78
If several codes are listed for your television brand,
TV POWER+67, +73,
▪
TELEFUNKEN
+75, +76
LOEWE
TV POWER+06, +69
try each one in turn until you find one that works.
TV POWER+72, +73,
+75
LOEWE OPTA TV POWER+06, +57
THOMSON
If you replace the remote control’s batteries, you
▪
MAGNAVOX
METZ
TV POWER+40
TV POWER+57
must set the brand code again.
THOMSON ASIA TV POWER+80, +81
TV POWER+47, +48,
TOSHIBA
TV POWER+06, +48,
MITSUBISHI
+49, +50, +51, +52
+62, +65
MIVAR
NEC
NEWSAN
TV POWER+52, +77
TV POWER+83
TV POWER+68
WEGA
YOKO
ZENITH
TV POWER+57
TV POWER+06
TV POWER+63
ꢀ0
English
Connections
Connecting to a Tv
Case 1 : Connecting to a TV with an HDMI Cable - Best Quality
(Recommended)
1. Using an HDMI cable, connect the HDMI OUT terminal on the rear of the player to the HDMI IN
terminal of your TV.
2. Turn on the player and TV.
3. Press the input selector on your TV remote control until the HDMI signal from the player appears on
your TV screen.
•
If you have set the remote control to operate your TV (See page 20), press the TV SOURCE
button on the remote control and select HDMI as the external source of the TV.
HDMI cable
(not included)
NOTE
✎
An HDMI cable outputs digital video/audio, so you don’t need to connect an audio cable.
▪
▪
If the player is connected to your TV in HDMI 720p, 1080i, 1080p output mode, you must use a High speed(category2)
HDMI cable.
HDMI outputs only a pure digital signal to the TV.
▪
If your TV does not support HDCP (High-bandwidth Digital Content Protection), random noise appears on the screen.
Depending on your TV, certain HDMI output resolutions may not work. Please refer to the user manual of your TV.
▪
▪
When you connect the player to the TV using the HDMI cable for the first time or to a new TV, the HDMI output
resolution will be automatically set to the highest supported by the TV.
You must have an HDMI connection to enjoy videos with 3D technology.
▪
▪
A long HDMI cable may cause a screen noise. If this is the case, set Deep Color to Off in the menu.
English
ꢀ1
Connections
Case 2 : Connecting to a TV with DVI Cable - Best Quality
(Recommended)
1. Using an HDMI-DVI cable, connect the HDMI OUT terminal on the rear of the player to the DVI IN
terminal of your TV.
2. Using the audio cables, connect the AUDIO OUT (red and white) terminals on the rear of the player
to the AUDIO IN (red and white) terminals of your TV.
3. Turn on the player and TV.
4. Press the input selector on your TV remote control until the HDMI-DVI signal from the player appears
on your TV screen.
•
If you have set the remote control to operate your TV (See page 20), press the TV SOURCE
button on the remote control and select HDMI-DVI as the external source of the TV.
HDMI-DVI cable
Audio cable
(not included)
TV monitor
Red
White
NOTE
✎
HDMI outputs only a pure digital signal to the TV. If your TV does not support HDCP (High-bandwidth Digital Content
Protection), random noise appears on the screen.
▪
Depending on your TV, certain HDMI output resolutions may not work. Please refer to the user manual of your TV.
▪
▪
When you connect the player to the TV using the HDMI-DVI cable for the first time or to a new TV, the HDMI output
resolution will be automatically set to the highest supported by the TV.
ꢀꢀ
English
Case 3 : Connecting to a TV (Component) - Better Quality
-
-
Connecting to your TV using Component video cables.
You will enjoy high quality images with accurate color reproduction. Component video separates the
picture element into black and white(Y), blue(PB) and red(PR) signals to present clear and clean images.
(Audio signals are delivered through the audio output.)
1. Using Component video cables, connect the COMPONENT OUT terminals on the rear of the player
2. Using the audio cables, connect the AUDIO OUT (red and white) terminals on the rear of the player
to the COMPONENT IN terminals of your TV.
to the AUDIO IN (red and white) terminals of your TV.
3. Turn on the player and TV.
4. Press the input selector on your TV remote control until the “COMPONENT” signal from the player
appears on the TV screen.
•
If you have set the remote control to operate your TV (See page 20), press the TV SOURCE
button on the remote control and select COMPONENT as the external source of the TV.
Component cable
(not included)
Audio cable
Red
White Red
Blue Green
NOTE
✎
Depending on the manufacturer, the component terminals on your TV may be marked “R-Y, B-Y, Y ” or “Cr, Cb, Y”
instead of “PB, PR, Y”. The number and position of terminals may vary depending on the TV set.
Please refer to the user manual of your TV.
▪
You can select from a variety of resolution settings for Blu-ray Discs such as 1080i, 720p, 480p, 480i, depending on
the disc type. (See pages 33~34)
▪
▪
▪
The actual resolution may differ from the setting in the setup menu if both Component and HDMI cables are connected.
The resolution may also be different depending on the disc. (See pages 33~34)
In DVD playback, if both HDMI and Component jacks are connected and you select the Component 1080p, 1080i or
720p mode, the Display Setup menu will show the output resolution as 1080p, 1080i or 720p in the menu.
The resolution is actually 480i.
English
ꢀꢁ
Connections
Case 4 : Connecting to a TV (Video) - Good Quality
1. Using video/audio cables, connect the VIDEO OUT (yellow) / AUDIO OUT (red and white)
terminals on the rear of the player to the VIDEO IN (yellow) / AUDIO IN (red and white) terminals of
your TV.
2. Turn on the player and TV.
3. Press the input selector on your TV remote control until the “VIDEO” signal from the player appears
on the TV screen.
•
If you have set the remote control to operate your TV (See page 20), press the TV SOURCE
button on the remote control and select VIDEO as the external source of the TV.
Audio/Video cable
Red
White Yellow
NOTE
✎
Noise may be generated if the audio cable is placed too close to the power cable.
▪
▪
▪
▪
If you want to connect to an Amplifier, please refer to the Amplifier connection pages. (See pages 25~27)
The number and position of terminals may vary depending on your TV set. Please refer to the user manual of your TV.
If there is only one audio input terminal on the TV, connect it to the AUDIO OUT(right/white) terminal of the player.
CAUTION
!
Do not connect the unit through a VCR. Video signals fed through VCRs may be affected by copyright protection
▪
systems and the picture will be distorted on the television.
ꢀꢂ
English
Connecting to an Audio System
•
Please turn the volume down when you turn on the Amplifier. Sudden loud sound may cause
damage to the speakers and your ears.
•
•
Please set the audio in the menu screen according to the Amplifier. (See pages 35~37)
The position of HDMI terminals may vary depending on the Amplifier. Please refer to the user manual
of your Amplifier.
Case 1 : Connecting to an Audio System (HDMI Supported Amplifier)
- Best Quality (Recommended)
1. Using an HDMI cable, connect the HDMI OUT terminal on the rear of the player to the HDMI IN
terminal of your Amplifier.
2. Using an HDMI cable, connect the HDMI OUT terminal of the Amplifier to the HDMI IN terminal of
your TV.
3. Turn on the player, TV and Amplifier.
4. Press the input select button of the Amplifier to select the external input in order to hear sound from
the player. Refer to your Amplifier’s user manual to set the Amplifier’s audio input.
HDMI cable
(not included)
HDMI cable
(not included)
English
ꢀꢃ
Connections
Case 2 : Connecting to an Audio System (7.1 Channel Amplifier)
- Better Quality
1. Using the 7.1CH audio cables, connect the 7.1CH ANALOG AUDIO OUT terminals on the rear of
the Player to the 7.1CH ANALOG AUDIO IN terminals of your Amplifier.
2. Using the video signal cable(s), connect the HDMI, COMPONENT or VIDEO OUT terminals on the
rear of the Player to the HDMI, COMPONENT or VIDEO IN terminal of your TV. (See pages 21~24)
3. Turn on the Player, TV and Amplifier.
4. Press the input select button of the Amplifier to select the external input in order to hear sound from
the Player. Refer to your Amplifier’s user manual to set the Amplifier’s audio input.
7.1CH audio cables
(not included)
7.1 Channel Amplifier
NOTE
✎
The front left and right outputs on your player and 7.1 channel amplifier must be connected to hear disc menu audio
from certain Blu-ray discs.
▪
▪
▪
When you connecting the 7.1CH ANALOG AUDIO OUT terminals using 7.1CH audio cables, it is recommended to set
the Digital Output to PCM. (See page 35)
When connecting to a 5.1 channel home theater or receiver, connect all the Analog Audio output jacks from the player
except for the Surround Back Left/Surround Back Right outputs.
ꢀꢄ
English
Case 3 : Connecting to an Audio
System (Dolby Digital, DTS
Amplifier) - Better Quality
Case 4 : Connecting to an Audio
System (2 Channel Amplifier)
- Good Quality
1. Using an optical cable, connect the DIGITAL
AUDIO OUT (OPTICAL) terminal on the
rear of the player to the DIGITAL AUDIO IN
(OPTICAL) terminal of your Amplifier.
1. Using the audio cables, connect the AUDIO
OUT (red and white) terminals on the rear of
the player to the AUDIO IN (red and white)
terminals of your Amplifier.
2. Using the video signal cable(s), connect
the HDMI, COMPONENT or VIDEO OUT
terminals on the rear of the player to the
HDMI, COMPONENT or VIDEO IN terminal
of your TV. (See pages 21~24)
2. Using the video signal cable(s), connect
the HDMI, COMPONENT or VIDEO OUT
terminals on the rear of the player to the
HDMI, COMPONENT or VIDEO IN terminal
of your TV. (See pages 21~24)
3. Turn on the player, TV and Amplifier.
3. Turn on the player, TV and Amplifier.
4. Press the input select button of the Amplifier
to select the external input in order to
hear sound from the player. Refer to your
Amplifier’s user manual to set the Amplifier’s
audio input.
4. Press the input select button of the Amplifier
to select the external input in order to
hear sound from the player. Refer to your
Amplifier’s user manual to set the Amplifier’s
audio input.
Case 3 :
Case 4 : Audio cable
Optical cable
(not included)
Red
White
NOTE
✎
When following the case 3 connection, discs with PCM audio soundtracks will only be heard over the front two
channels.
▪
English
ꢀꢅ
Connections
Connecting to the Network
This player enables you to view network based services (See pages 55~60) such as Internet@TV and
BD-LIVE, as well as receive software upgrades when a network connection is made. We recommend
using an AP (Access Point) or IP router for the connection. For more information on router connection,
refer to the user manual of the router or contact the router manufacturer for technical assistance.
Cable Network
1. Using the Direct LAN Cable (UTP cable), connect the LAN terminal of the player to the LAN terminal
of your modem.
2. Set the network options. (See pages 39~43)
Router
Or
Broadband modem
(with integrated router)
Broadband modem
Broadband
service
Broadband
service
Networking with PC for
AllShare function
(See pages 59~60)
NOTE
✎
Internet access to Samsung’s software update server may not be allowed, depending on the router you use or the ISP’s
policy. For more information, contact your ISP (Internet Service Provider).
▪
For DSL users, please use a router to make a network connection.
▪
▪
For the AllShare function, a PC must be connected in the network as shown in the figure.
ꢀꢆ
English
Wireless Network
You can connect to network with a Wireless IP sharer.
A wireless AP/IP router is required to make a wireless network connection.
Set the network options. (See pages 39~43)
Broadband
service
Wireless IP sharer
Networking with PC for
AllShare function
(See pages 59~60)
NOTE
✎
To use a wireless network, your player must be connected to a wireless IP sharer. If the wireless IP sharer supports
DHCP, your player can use a DHCP or static IP address to connect to the wireless network.
▪
▪
▪
▪
This player supports IEEE 802.11B, IEEE 802.11G, IEEE 802.11N. When you play the video over IEEE 802.11B/G
connection, the video may not be played smoothly.
Select a channel for the wireless IP sharer that is not currently being used. If the channel set for the wireless IP sharer
is currently being used by another device nearby, this will result in interference and communication failure.
If Pure High-throughput (Greenfield) 802.11n mode is selected and the Encryption type is set to WEP, TKIP or TKIP-
AES (WPS2Mixed) for your AP, this player will not support a connection in compliance with new Wi-Fi certification
specifications.
If your AP supports WPS (Wi-Fi Protected Setup), you can connect to the network via PBC (Push Button Configuration)
or PIN (Personal Identification Number). WPS will automatically configure the SSID and WPA key in either mode.
▪
▪
Connection Methods : You can setup the wireless network connection 3 ways.
-
-
-
PBC (WPS)
Auto Setup (Using the Auto Network Search function)
Manual Setup
Wireless LAN, by its nature, may cause interference, depending on the use condition (AP performance, distance,
▪
obstacles, interference by other radio devices, etc).
Set the wireless IP sharer to Infrastructure mode. Ad-hoc mode is not supported.
When applying the security key for the AP (wireless IP sharer), only the following is supported.
1) Authentication Mode : WEP, WPAPSK, WPA2PSK
▪
▪
2) Encryption Type : WEP, AES
For the AllShare function, a PC must be connected in the network as shown in the figure.
▪
English
ꢀꢇ
Setup
5. Press the ◄► buttons to the select the
desired Network Settings: Wired, Wireless or
PBC (WPS), then press the ENTER button.
(See pages 40~43)
Before Starting (Initial Settings)
1. Turn on your TV after connecting the player.
(When the player is connected to TV for the
first time, player will turn on automatically and
the Initial Settings screen will be displayed.)
The Network Test will start and Initial Settings
will be completed.
6. Press the OK button.
Initial Settings I On-Screen Language
Select a language for the on-screen displays.
The home menu will be displayed. (For more
information about home menu, please see
page 31)
English
Français
Deutsch
Español
Italiano
•
Home Menu
Nederlands
Please activate Intern
e
t
@
T
V service
to enjoy a variety of Internet Services.
> Move " Select
2. Press the ▲▼ buttons to select desired
language, then press the ENTER button.
3. Press the ENTER button to select Start
No Disc
a Change Device
d View Devices " Enter
button.
Initial Settings
NOTE
✎
TV Aspect and Network will be set.
When the player is connected to TV for the first time,
player will turn on automatically.
▪
Each setting may be changed later under "Settings"
Do not confuse because this is not malfunction.
The home menu will not be displayed if you do not
▪
▪
configure the initial settings.
Start
If you press the BLUE(D) button during the network
setup, you can access the home menu even if the
network setup is not completed yet.
a
Previous " Select
When you return to home menu, the full screen
▪
▪
4. Press the ▲▼ buttons to select the desired
TV Aspect ratio, then press the ENTER
button. (See page 33)
mode will be cancelled automatically.
If you want to display Initial Setting screen again
in order to make changes, press the STOP (
)
button on the front panel of the player for more than
Initial Settings I Network
5 seconds with no disc inserted.
Network Setting is needed to use various Internet services.
Use the HDMI cable to connect the player to an
Anynet+(HDMI-CEC)-compliant Samsung TV.
If the TV uses a language supported by the player,
that language will be set to a preferred language
automatically.
▪
Choose the primary method for connecting to network.
Wired : Set the network connection using the Ethernet cable.
Please make sure that the Ethernet cable is connected.
Wireless
Previous
PBC (WPS)
Wired
However, the Anynet+(HDMI-CEC) feature should
be set to On in both TV and the player.
a
d
Skip < Move " Select
ꢁ0
English
If the player is left in the stop mode more than 5
minutes without being used, a screen saver will
appear on your TV. If the player is left in the screen
saver mode for more than 25 minutes, the power
will automatically turn off.
▪
Selects the Settings.
Displays buttons available.
5
6
2. Press the ◄► buttons to select Settings,
then press the ENTER button.
3. Press the ▲▼ buttons to select the desired
Setting the Menu
submenu, then press the ENTER button.
4. Press the ▲▼ buttons to select the desired
DISC MENU
MENU
TITLE MENU
POPUP
item, then press the ENTER button.
1
2
TOOLS
INFO
5. Press the EXIT button to exit the menu.
NOTE
✎
3
4
When the player is connected to the network, select
Internet@TV from the home menu.
Download desired content from Samsung Apps.
(See page 58)
▪
RETURN
EXIT
MENU Button : Press this to move to the home menu.
The access step may differ depending on the
1
▪
▪
selected menu.
RETURN Button : Return to the previous menu.
2
3
4
The OSD (On Screen Display) may change in this
player after upgrading the software version.
ENTER / DIRECTION Button :
Move the cursor or select an item.
Select the currently selected item.
Confirm the setting.
EXIT Button : Press this to exit the menu.
1. Press the POWER button.
The Home Menu will appear.
•
Home Menu
Please activate Intern
e
t
@
T
V service
to enjoy a variety of Internet Services.
2
3
4
1
5
6
No Disc
a Change Device
d View Devices " Enter
Selects the Internet@TV.
Selects the Videos.
Selects the Music.
1
2
3
4
Selects the Photos.
English
ꢁ1
Setup
Display
TV Screen Size
Lets you enter the actual screen size of your TV so that
the player can adjust the image according to the screen
size and display an optimal 3D image.
You can configure various display options such as
t3hDe TV Aspect, Resolution, etc.
(The maximum allowed screen size is 116 inches for
this player.)
Select whether to play a Blu-ray Disc with 3D
contents in 3D Mode.
CAUTION
!
If you want to enjoy a 3D content, connect a 3D
device (3D compliant AV receiver or TV) to the
product and wear a 3D glass before playing the 3D
content.
▪
Settings
Display
3D
3D
Audio
While watching the 3D video, all analog component
and composite signals will be blocked automatically.
▪
▪
▪
System
Network
Language
Security
General
Support
\
3D Mode
: Auto
55
TV Screen Size
:
inch
All 3D signals are output only using the HDMI cable
and through the HDMI OUT port.
> Move " Enter ' Return
As the video resolution in 3D play mode is fixed
according to the resolution of the original 3D
video, you can not change the resolution to your
preference.
Still Mode
: Auto
Some functions such as BD Wise, or setting the
screen size or resolution may not operate properly in
3D play mode.
▪
3D Mode
•
Auto : You can choose whether to watch 3D
Blu-ray disc in 3D or 2D mode before playing
the 3D Blu-ray. It is automatically played in 2D
mode if your TV cannot support 3D contents.
You must use a high-speed HDMI cable for a proper
output of the 3D signal.
▪
▪
Stay at least three times of the length of the screen
distant from the TV.
•
•
3D : The 3D Blu-ray Disc is played in 3D mode
at all times. If a TV cannot support 3D Blu-ray
discs, the playing screen can be black.
- It is recommended to place the 3D video screen
forward at eye level.
2D : The 3D Blu-ray Disc is played in 2D mode
at all times. Choose this to view a picture
without 3D effect or when a TV cannot support
3D Blu-ray discs.
If the product is connected to some 3D devices, the
3D effect may not function properly.
▪
▪
▪
You can not use this product for switching a 2D
content to 3D.
NOTE
✎
“Blu-ray 3D” and “Blu-ray 3D” logo are trademarks
of Blu-ray Disc Association.
If you press the STOP(
) button once during
▪
the 3D disc playback, 3D mode option will not be
activated.
To activate 3D mode option during the 3D disc
playback, press the STOP(
) button twice.
Depending on the content and its play position,
vertical black bars could be seen on left or right or
both sides.
▪
ꢁꢀ
English
TV Aspect
BD Wise (Samsung Players only)
Depending on the type of television you have, you
may want to adjust the screen setting.
BD Wise is Samsung’s latest inter-connectivity
feature.
When you connect Samsung players with BD
Wise to each other via HDMI, the optimum
resolution will be set automatically.
•
•
•
16:9 Normal
Certain movies(4:3 source) will be
displayed in 4:3 Pillarbox (black
bars on sides of picture) if 16:9
normal is selected.
•
•
On : The original resolution of the BD/DVD disc
will be output to the TV.
Off : The output resolution will be fixed
according to the Resolution previously set,
regardless of the resolution of the disc.
16:9 Wide
NOTE
✎
You can view the full 16:9 picture
on your widescreen TV.
If you want to change the resolution in BD Wise, you
▪
▪
must set BD Wise to Off in advance.
If you set off the BD Wise, the resolution of the
connected TV will be adjusted to its maximum
resolution automatically.
4:3 Letter Box
If the player is connected to a device that does not
support BD Wise, you can not use the BD Wise
function.
▪
▪
Select when you want to see the
total 16:9 ratio screen a Blu-ray
Disc/DVD supplies, even though
you have a TV with a 4:3 ratio
screen. Black bars will appear at
the top and bottom of the screen.
For proper operation of BD Wise, set the BD Wise
menu of both the product and the TV to On.
Resolution
•
4:3 Pan-Scan
Sets the output resolution of the Component and
HDMI video signal.
Select when you want to see the
16:9 video supplied by the Blu-ray
Disc/DVD without the black bars
on top and bottom, even though
you have a TV with a 4:3 ratio
The number in 1080p, 1080i, 720p, 480p, 480i
indicates the number of lines of video.
The i and p indicate interlace and progressive
scan, respectively.
screen(extreme left and right portion
of the movie picture will be cut off).
•
•
Auto : It automatically checks and sets the
optimal resolution.
BD Wise : Automatically sets the optimal
resolution when connected via HDMI to a TV
with the BD Wise feature. (The BD Wise menu
item appears only if BD Wise is set to On.)
NOTE
✎
Depending on the disc type, some aspect ratios may
not be available.
▪
▪
If you select an aspect ratio and option which is
different than the aspect ratio of your TV screen,
then the picture might appear to be distorted.
•
1080p : Outputs 1080 lines of progressive
video.
•
•
•
•
1080i : Outputs 1080 lines of interlaced video.
720p : Outputs 720 lines of progressive video.
480p : Outputs 480 lines of progressive video.
480i : Outputs 480 lines of interlaced video.
If you select the 4:3 Pan-Scan or 4:3 Letter Box, you
can’t see full screen by pressing the FULL SCREEN
button on the remote control.
▪
▪
If you select the 16:9 Normal, 4:3 Pillarbox may
displayed.
In this case, you can’t see full screen by pressing
the FULL SCREEN button on the remote control.
English
ꢁꢁ
Setup
Resolution according to the output mode
•
Blu-ray Disc playback
HDMI / connected
HDMI / not connected
Output
Setup
HDMI Mode
Component/VIDEO Mode
Component Mode
VIDEO Mode
Auto
Optimal Resolution
1080p@60F
480i
480i
-
-
-
-
1080p, Movie Frame(24Fs) off
1080p/1080i,
1080p@24F
480i
-
-
Movie Frame(24Fs) on
1080i, Movie Frame(24Fs) off
1080i
720p
480p
-
480i
480i
480i
-
1080i
720p
480p
480i
480i
480i
480i
480i
720p
480p
480i
•
DVD playback
HDMI / connected
HDMI / not connected
Output
Setup
HDMI Mode
Optimal Resolution
1080p@60F
1080i
Component/VIDEO Mode
Component Mode
VIDEO Mode
Auto
1080p
1080i
720p
480p
480i
480i
480i
480i
480i
480i
-
-
-
-
-
480p
480p
480p
480i
480i
480i
480i
480i
720p
480p
-
NOTE
If the screen is blank, press and hold the STOP (
)
✎
▪
button on the front of the player for more than 5
If the connected TV does not support Movie Frame or
the selected resolution, the message “If no pictures
are shown after the selection, please wait for 15
seconds. And then, the resolution will be reverted to
the previous value automatically. Would you like to
make a selection?” will be displayed.
▪
seconds (no disc inserted). All settings are restored to
the factory default. Follow the steps on the previous
page to access each mode and select the Display
Setup that your TV will support.
When the factory default settings are restored, all
▪
▪
▪
If you select Yes and the resolution is not supported,
the TV’s screen will be blank. Please wait for 15
seconds and the resolution will be reverted to the
previous value automatically.
the user data stored in the BD data will be deleted.
The Blu-ray Disc must have the 24 frame feature in
order to use the Movie Frame (24Fs) mode.
If both HDMI and Component jacks are connected
and you are currently viewing component output,
there is a difference between resolution table and
actual resolution depending on your TV.
ꢁꢂ
English
HDMI Format
HDMI Deep Color
You can optimize the color setting from the HDMI
output.
Set to output the picture from the HDMI OUT jack
with Deep Color or not. Deep Color allows more
accurate color reproduction with deeper color
depth.
Select a connected device Type.
•
•
TV : Select if connected to a TV via HDMI.
HDMI.
•
Auto : The picture will be output with Deep
Color to the connected TV which supports
HDMI Deep Color.
Monitor : Select if connected to a Monitor via
•
Off : The picture will be output without Deep
Movie Frame (24Fs)
Color.
Setting the Movie Frame (24Fs) feature to On
allows you to adjust the player’s HDMI output to
24 frames per second for improved picture quality.
You can enjoy the Movie Frame (24Fs) feature only
on a TV supporting this frame rate. This menu can
only be selected in 1080i or 1080p HDMI output
resolution modes.
Audio
Digital Output
Set Digital Output depending on the connected
receiver. (For more details, please refer to the
digital output selection on the next page)
•
•
✎
On : Movie Frame (24Fs) functions will work.
Off : Movie Frame (24Fs) functions will not work.
•
•
•
PCM
NOTE
Bitstream(Re-encode)
If your TV does not support Movie Frame (24Fs)
function, the pop-up message will be displayed.
▪
Bitstream(Audiophile)
NOTE
✎
Be sure to select the correct Digital Output or you
will hear no sound or a loud noise.
▪
▪
Progressive Mode
Set to improve picture quality when viewing DVDs.
If the HDMI device (Receiver, TV) is not compatible
with compressed formats (Dolby digital, DTS), the
audio signal outputs as PCM.
•
Auto : Select this to have the player
automatically set the best picture for the DVD
you’re watching.
Regular DVDs do not have BONUSVIEW audio and
▪
▪
▪
•
Video : Select for the best picture quality from
Navigation Sound Effects.
concert or TV show DVDs.
Some Blu-ray Discs do not have BONUSVIEW audio
and Navigation Sound Effects.
Still Mode
This Digital Output setup does not effect the analog
(L/R) audio or HDMI audio output to your TV.
It effects the optical and HDMI audio output when
connected to a receiver.
Set the type of picture shown when you pause
DVD playback.
•
•
•
Auto : Automatically set the best still picture
If you play MPEG audio soundtracks, audio signal
outputs PCM regardless of Digital Output Selections
(PCM or Bitstream).
▪
depending on the content.
Frame : Select when pausing a scene with a
little action.
Field : Select when pausing a scene with a lot
of action.
English
ꢁꢃ
Setup
Digital Output Selection
Bitstream
Bitstream
Setup
PCM
(Re-encode)
(Audiophile)
Connection
HDMI Receiver Optical
HDMI Receiver or Optical HDMI Receiver
Optical
PCM
Up to 7.1ch
Up to 5.1ch
PCM 2ch
PCM 2ch
DTS re-encoded
DTS re-encoded
PCM
PCM 2ch
Dolby Digital
Dolby Digital
Dolby Digital
Dolby Digital
Dolby Digital
Up to 7.1ch
PCM 2ch
DTS re-encoded
Dolby Digital
Audio Stream
on Blu-ray
Disc
Plus
Plus
Dolby TrueHD Up to 7.1ch
PCM 2ch
PCM 2ch
PCM 2ch
PCM 2ch
PCM 2ch
PCM 2ch
PCM 2ch
DTS re-encoded
DTS re-encoded
DTS re-encoded
DTS re-encoded
PCM 2ch
Dolby Digital
DTS
Dolby TrueHD Dolby Digital
DTS
Up to 6.1ch
DTS
DTS
DTS
DTS
DTS-HD HRA Up to 7.1ch
DTS-HD HRA
DTS-HD MA
PCM 2ch
Dolby Digital
DTS
DTS-HD MA
PCM
Dolby Digital
DTS
Up to 7.1ch
PCM 2ch
Up to 5.1ch
Up to 6.1ch
PCM 2ch
Dolby Digital
DTS
Audio Stream
on DVD
Decodes main feature audio Outputs only main feature audio
and BONUSVIEW audio stream stream so that your AV receiver
together into PCM audio and can decode the audio bitstream.
add Navigation Sound Effects, You will not hear BONUSVIEW
then re-encodes the PCM audio audio and Navigation Sound
Decodes main feature audio
and BONUSVIEW audio
stream together into PCM
audio and add Navigation
Sound Effects.
Definition for
Blu-ray Disc
Any
into DTS bitstream.
Effects.
Blu-ray Discs may include three audio streams.
PCM Downsampling
-
-
-
Main Feature Audio : The audio soundtrack of
the main feature.
Set whether to downsample 96kHz signals.
•
On : Select this when the Amplifier connected
to the player is not 96kHz compatible. 96kHz
signals will be down converted to 48kHz.
BONUSVIEW audio : Additional soundtrack
such as director or actor's commentary
Navigation Sound Effects : When you choose
some menu navigation, Navigation Sound
Effects may sounds. Navigation Sound Effects
is different on each Blu-ray Disc.
•
Off : Select this when the Amplifier connected
to the player is 96kHz compatible.
NOTE
✎
Even when PCM Downsampling is set to Off, some
discs will only output downsampled audio through
the optical digital outputs.
▪
ꢁꢄ
English
•
•
Cinema : Select this if you want to play
HDMI
2-channel movie sound over multi-channels.
•
If your TV is not compatible with compressed
Music : Select this if you want to play 2-channel
multi-channel formats (Dolby Digital, DTS), the
player may output PCM 2ch downmixed audio
even though you set Bitstream(either Re-encode
or Audiophile) on your setup menu.
music sound over multi-channels.
NOTE
✎
If you are using HDMI receiver, this option is
▪
▪
•
If your TV is not compatible with PCM sampling
rates over 48kHz, the player may output 48kHz
downsampled PCM audio even though you set
PCM Downsampling to Off.
available when you set Digital Output setup as PCM.
You can use this option with analog 7.1ch output
when you don’t use HDMI receiver.
Speaker Setting
Dynamic Range Control
Set the speaker sound to obtain the best possible
surround sound.
You can listen at low volumes but still hear dialog
clearly.
This menu is available only when using 7.1ch
analog output.
This is only active when a Dolby Digital signal is
detected.
•
Auto : The Dynamic Range Control will be set
automatically based on the information provided
by the Dolby TrueHD Soundtrack.
Settings
Display
Speaker Setting
Front
Audio
:
Large
•
On : When Movie soundtracks are played at low
volume or from smaller speakers, the system
can apply appropriate compression to make
low-level content more intelligible and prevent
dramatic passages from getting too loud.
System
Network
Languag
Security
General
Support
Center
:
:
:
:
:
Large
Large
Large
On
Surround
Surround Back
Subwoofer
Test Tone
Off
< Change " Enter ' Return
•
Off : You can enjoy the movie with the standard
Dynamic Range.
Test Tone
Downmixing Mode
;
;
;
;
•
A test tone will be sent to L
C
R
RS
Set whether to downmix the multi-channel audio
into fewer channels.
;
;
;
RSB LSB LS LFE in order, so you can
make sure the speakers are set up correctly.
•
Normal Stereo : Downmixes the multi-channel
audio into two channel stereo. Choose when
connected to equipment that does not support
virtual surround functions such as Dolby Pro
Logic.
•
•
The test tone can only be activated when no
discs are in the unit.
The test tone outputs through the 7.1 channel
analog outputs only.
•
Surround Compatible : Downmixes multi-
channel audio into surround compatible stereo.
Choose when connected to equipment that
supports virtual surround functions such as
Dolby Pro Logic.
DTS Neo:6
You can enjoy multi-channel sound from a simple
2-channel audio source.
•
Off : Outputs a 2-channel audio signal through
the front speakers only.
English
ꢁꢅ
Setup
System
BD Data Management
Enables you to manage the downloaded contents
from a Blu-ray Disc that supports the BD-LIVE
service.
Initial Settings
By using Initial Settings, you can set language, TV
aspect and Network Settings, etc.
You can check the device information including
the storage size, delete the BD data or change the
Flash memory device.
For more information on the settings, refer to the
corresponding section in this user manual.
(See pages 30~45)
Change Device allows you to select either the
player’s Internal Memory or External Memory
(connected USB Device).
Internet@TV Screen Size
If the data to be stored from BD-LIVE is greater
than the size of the remaining memory or the
Internal Memory is full, connect an External USB
device, then select External Device in the menu.
Set the Internet@TV Screen to the optimal size.
•
•
•
Size 1 : Display smaller application icons, you
may see some black on sides of screen.
Size 2 : Display normal application icons, image
Settings
may be too large for your TV screen.
Size 3 : Display larger application icons, image
Display
BD Data Management
Audio
may be too large for your TV screen.
Current Device
:
Internal Flash Memory
System
Network
Language
Security
General
Support
Total Size
: 589MB
: 588MB
Available Size
Delete BD Data
Change Device
\
Anynet+(HDMI-CEC)
:
Internal Flash Memory
Anynet+ is a convenient function that offers linked
operations with other Samsung players with the
Anynet+ feature.
" Select ' Return
To operate this function, connect this player to a
Samsung TV with an HDMI cable.
Description of Device(Storage) Information on
the Player
You can operate this player using a Samsung TV
remote control and start disc playback simply
•
•
Total Size : Total size of the Device(Storage).
by pressing the PLAY (
) button on the TV’s
Available Size : Available size of the Device
remote control.
(Storage).
NOTE
For more information, please see the TV user
manual.
✎
•
•
✎
On : Anynet+ functions will work.
In the external memory mode, disc playback will
be stopped if you disconnect the USB device in the
middle of the playback.
▪
▪
Off : Anynet+ function will not work.
NOTE
Only those USB devices formatted in FAT file system
(DOS 8.3 volume label) are supported, and it is
recommended to use USB devices that support USB
2.0 protocol, 4 MB/sec or faster read/write speed.
This function is not available if the HDMI cable does
not support CEC.
▪
▪
▪
If your Samsung TV has an n logo, then it
supports the Anynet+ function.
The Resume Play function may not work after
▪
▪
Depending on your TV, certain HDMI output
formatting the storage device.
resolutions may not work.
The total size of BD Data Management may differ,
depending on the conditions.
Please refer to the user manual of your TV.
ꢁꢆ
English
Clock
DivX(R) Deactivation
Set time-related functions.
Select this to get a new registration code.
Settings
Settings
Display
Clock
Display
Initial settings
Disc Menu
Audio
Clock Mode
Clock Set
Time Zone
DST
: Auto
\
Audio
:
System
Network
Language
Security
General
Support
System
Network
Language
Security
General
Support
: GMT + 0:00
: Off
Do you want to deactivate your device?
Yes
No
> Move " Enter ' Return
•
Clock Mode : You can set it to Auto or
Manual.
NOTE
✎
This function can be operated when DivX(R)
Registration function is deactivated.
▪
If you select Manual, the Clock Set menu will
be activated while DST will be deactivated.
•
•
•
Clock Set : You can specify the current time
and date manually.
Network
Time Zone : You can specify the time zone that
To begin setting up the network connection for
is applicable to your area.
your player, follow these steps:
DST : You can set DST (Daylight Saving Time)
on or off.
1. In the Home menu, press the ◄► buttons
to select the Settings, and then press the
ENTER button.
DivX(R) Registration
2. Press the ▲▼ buttons to select Network, and
View DivX(R) VOD Registration Code to purchase
and play DivX(R) VOD content.
then press the ENTER button.
3. Press the ▲▼ buttons to select Network
Settings, and then press the ENTER button.
Settings
4. Press the ▲▼ buttons to select Network
Display
Initial settings
Disc Menu
Type, and then press the ENTER button.
Audio
:
System
Network
Language
Security
General
Support
5. Press the ▲▼ buttons to select Wired or
DivX(R) Video On Demand
Your registration code is : XXXXXXXXXX
Wireless, and then press the ENTER button.
6. Go to the next section.
OK
Network Settings
Please contact your ISP to find out if your IP
address is static or dynamic. If it is dynamic, we
recommend using the Auto setting. This is the
easiest and will work in the majority of cases. If it is
static, you must use the manual set up procedure.
NOTE
✎
This option is not activated if you select OK.
To activate this option, please activate the DivX(R)
Deactivation.
▪
Directions for wired networks are below. Directions
for wireless networks are after the directions for
wired networks.
English
ꢁꢇ
Setup
Setting Up a Wired Connection - Manual
Wired Network
If the Auto Setting does not work, you’ll need to
set the Network Setting values manually.
1. In the Network Settings menu, press the ▲▼
buttons to select Network Setting, and then
press the ENTER button.
To get the Network setting values from most
Windows computers, follow these steps:
The Internet Protocol Setup screen appears.
1. Right click the Network icon on the bottom
2. Press the ► button, then select Auto or
right of the screen.
Manual, and then press the ENTER button.
2. In the pop-up menu, click Status.
Setting Up a Wired Connection - Auto
3. On the dialog that appears, click the Support
tab.
1. If you selected Auto, the Network Function
acquires and fills in the values for IP Address,
Subnet Mask, etc., automatically.
4. On the Support tab, click the Details button.
The Network settings are displayed.
NOTE
✎
To enter the Network settings into your player,
This process can take up to five minutes.
follow these steps:
▪
1. On the Internet Protocol Setup screen, press
Settings
the ENTER button.
Network Setting
Displa
2. Press the ▲▼ buttons to select Manual, and
Internet Protocol Setup : Auto
\
Audio
IP Address
Subnet Mask
Gateway
:
:
:
0
0
0
0
0
0
0
0
0
0
0
0
then press the ENTER button.
System
Netwo
Langu
3. Press the ▼ button to go to the first entry field
DNS
: Auto
(IP Address).
Securi
Gener
Suppo
DNS Server
:
0
0
0
0
Settings
> Move " Select ' Return
Network Setting
Displa
Internet Protocol Setup : Manual
\
Audio
IP Address
Subnet Mask
Gateway
:
:
:
0
0
0
0
0
0
Syste
Netwo
Langu
255 255 255
0
0
0
0
0
2. After the Network Function has acquired the
network values, press the RETURN button.
Then, run a Network Test to ensure the player
has connected to your network (See page 43).
DNS
: Manual
Secur
Gener
Suppo
DNS Server
:
0
0
> Move " Select ' Return
3. If the Network Function does not acquire the
network values or you selected Manual, go to
the directions for Manual Setup.
4. Use the number buttons on your remote to
enter numbers.
5. When done with each field, use the ► button
to move successively to the next field.
You can also use the other arrow buttons to
move up, down, and back.
6. Enter the IP Address, Subnet Mask, and
Gateway values.
7. Press the ▼ button to go to DNS.
8. Press the ▼ button to go to the first DNS
entry field. Enter the numbers as above.
ꢂ0
English
9. Press the RETURN button on your remote.
Setting Up the Network Connection
.
10. Run a Network Test to ensure the player has
To set up the wireless connection using Auto
connected to your network (See page 43).
Network Search, follow these steps:
1. In the Network Settings menu, press the ▲▼
buttons to select Network Setting, and then
press the ENTER button.
Wireless Network
You can setup the wireless network three ways:
The Internet Protocol Setup screen appears.
•
•
•
Using PBC (WPS)
2. Press the ▲▼ buttons to select the Internet
Protocol Setup, and then press the ENTER
button.
Using the Auto Network Search function.
Manually.
Each method is described below.
3. Press the ▲▼ buttons to select Auto or
Manual, and then press the ENTER button.
Setting Up the Wireless Network Connection
- PBC (WPS)
Settings
The easiest way to set up the wireless network
connection is using the PBC (WPS) function.
If your wireless router has a PBC (WPS) button,
follow these steps:
Network Setting
Displa
Access Point Selection : Not Selected
Internet Protocol Setup : Auto
\
Audio
System
Netwo
Langu
Securi
IP Address
Subnet Mask
Gateway
:
:
:
0
0
0
0
0
0
0
0
0
0
0
0
1. In the Network Settings menu, press the ▲▼
buttons to select Network Setting, and then
press the ENTER button.
DNS
: Auto
Gener
Suppo
DNS Server
:
0
0
0
0
a
PBC (WPS) > Move " Select ' Return
The Internet Protocol Setup screen appears.
2. Press the RED(A) button on the remote
control.
4. If you selected Auto, press the ▲ button to
go to Access Point Selection, and then
press the ENTER button.
3. Press the PBC (WPS) button on your router
within two minutes. Your player displays the
Network Selection Screen, and automatically
acquires all the network setting values it
needs and connects to your network. When
it is done, it displays an OK button. Press the
ENTER button on your remote.
The Network function searches for available
wireless networks.
When done, it displays a list of the available
networks.
5. In the list of networks, press the ▲▼ buttons
to select a network, and then press the
ENTER button.
4. After the network connection is set up, press
the RETURN button to exit the Network
Setting screen.
6. If the PIN/Security pop-up appears, go to
Step 7. If the Network Connecting Screen
appears, go to Step 11.
Setting Up the Wireless Network Connection
- Auto Network Search
Most wireless networks have an optional security
system that requires devices that access the
network to transmit an encrypted security code
called an Access or Security Key. The Security
Key is based on a Pass Phrase, typically a word
or a series of letters and numbers of a specified
length you were asked to enter when you set up
security for your wireless network. If you use this
method of setting up the network connection, and
have a Security Key for your wireless network,
you will have to enter the Pass Phrase during the
setup process.
7. Press the ▲▼ buttons to select PIN or
Security.
For most home networks, you would select
Security (for Security Key).
8. On the Security screen, enter your network’s
Pass Phrase.
English
ꢂ1
Setup
NOTE
12. To test the connection, press the ▼ button
to select Network Test, and then press the
ENTER button.
✎
You should be able to find the Pass Phrase on one of
▪
the set up screens you used to set up your router or
modem.
Setting Up the Wireless Network Connection
- Manual
Settings
If the Auto Setting does not work, you need to
enter the Network settng values manually.
Security Key
Display
Security Key
(0)
Audio
a
b
c
5
8
0
System
Network
Language
Security
General
Support
To get the Network setting values from most
.,@
abc
jkl
def
mno
1
4
7
2
3
6
9
ghi
Windows computers, follow these steps:
pqrs
tuv
wxyz
Delete
Done
a/A/a/
1. Right click the Network icon on the bottom
a
Clear All
b
Space
c
right of the screen.
(/)
Cursor " Select ' Return
2. In the pop-up menu, click Status.
3. On the dialog that appears, click the Support
tab.
4. On the Support tab, click the Details button.
9. To enter the Pass Phrase, follow these
The Network settings are displayed.
general directions:
•
Press the number keys on your remote to
To Enter the Network settings into your player,
enter numbers.
follow these steps:
•
Use the arrow keys on your remote to move
from button to button on the Security Key
screen.
1. On the Internet Protocol Setup screen, press
the ENTER button.
2. Press the ▲▼ buttons to select Manual, and
•
To enter letters, move to the button labeled
then press the ENTER button.
a/A/1/ , and then press the ENTER button.
3. Press the ▼ button to go to the first entry field
Each time you press the ENTER button,
(IP Address).
you change the kind of characters you can
enter (a/A/1/ ).
Settings
•
•
•
To enter a letter, press the number button
that corresponds to the letter. Pressing the
button repeatedly changes the letter.
Network Setting
Displa
Access Point Selection : Not Selected
Internet Protocol Setup : Manual
\
Audio
Syste
Netwo
Langu
Secur
IP Address
Subnet Mask
Gateway
:
:
:
0
0
0
0
0
0
To delete the last letter or number you
entered, move to the Delete button, and
then press the ENTER button.
255 255 255
0
0
0
0
0
DNS
: Manual
Gener
Suppo
DNS Server
:
0
0
To clear all entered letters and numbers,
move to the Clear key, and then press the
ENTER button. You can also just press the
RED(A) button on your remote.
a
PBC (WPS) > Move " Select ' Return
4. Use the number buttons to enter numbers.
10. When done, press the YELLOW(C) button
on your remote, or move to the Done button,
and then press the ENTER button.
5. When done with each field, use the ► button
to move successively to the next field.
You can also use the other arrow buttons to
move up, down, and back.
The Network Connecting screen appears.
11. Wait until the connection confirmation
message is displayed, and then press the
ENTER button. The Network Settings screen
reappears.
ꢂꢀ
English
6. Enter the IP Address, Subnet Mask, and
NOTE
✎
Gateway values.
What is a valid certificate?
▪
When the player uses BD-LIVE to send the disc data
and a request to the server to certify the disc, the
server uses the transferred data to check if the disc is
valid and sends the certificate back to the player.
7. Press the ▼ to go to DNS.
8. Press the ▼ button to go to the first DNS
entry field. Enter the numbers as above.
9. When done, press the ▲ button to return to
Access Point Selection. Select the network,
and then press the ENTER button.
The Internet connection may be restricted while you
are using BD-LIVE contents.
▪
10. Go to Step 6 in the Automatic Wireless
procedure above, and follow the directions
from that point on.
Language
You can select the language you prefer for home
Network Test
menu, disc menu, etc.
Use this menu to connect the wired network
or check whether your network connection is
working or not.
•
•
On-Screen Menu : Select the language for the
on-screen displays.
Disc Menu : Select the language for the disc
menu displays.
•
Audio : Select the language for disc audio.
Settings
•
Subtitle : Select the language for disc subtitles.
Display
Network Test
Audio
NOTE
✎
MAC Address (00:00:00:00:00:00)
IP Address,Subnet Mask,Gateway,DNS Server
Gateway Ping
System
Network
Language
Security
General
Support
The selected language will only appear if it is
supported on the disc.
▪
Internet Service Test
Network testing...
Security
When you operate this menu for the first time,
password setup screen will be displayed.
Enter the desired 4-digit password using the
number buttons.
Network Status
Check whether a connection to the network and
the Internet have been established.
Parental Rating
BD-LIVE Internet Connection
This function works in conjunction with Blu-ray
Disc/DVDs that have been assigned a rating,
which helps you control the types of Blu-ray Disc/
DVDs that your family watches.
Set to allow internet connection when BD-LIVE
service is used.
•
•
Allow (All) : The Internet connection will be
allowed for all BD-LIVE contents.
Select the rating level you want to set.
Allow (Valid Only) : The Internet connection will
be allowed only for BD-LIVE contents containing
a valid certificate.
A larger number indicates that the program is
intended for adult use only. For example, if you
select up to Level 6, discs that contain Level 7, 8
will not play.
•
Prohibit : No Internet connection will be allowed
for any BD-LIVE content.
English
ꢂꢁ
Setup
Energy Saving
Settings
Display
Parental Rating
Off
You can reduce power consumption by setting
the front panel to turn off automatically when there
is no operation for 5 seconds.
Audio
Change Password
8(Adults)
System
Network
Language
Security
General
Support
7
6
5
4
•
•
On : The front panel will automatically turn off
Off : Energy Saving function is not used.
when there is no operation for 5 seconds.
|
Front Display
Change the brightness of the front panel.
Change Password
•
•
•
Auto : Dim during playback.
Change the 4-digit password used to access
security functions.
Dim : Dim the display window.
Bright : Brighten the display window.
If you forgot your password
Power On/Off Sound
1. Remove the disc.
Play a melody when the player is turned on and off.
2. Press and hold the STOP (
) button on the
•
On : Turn Power Sound On.
front panel for 5 seconds or more.
•
Off : Turn Power Sound Off.
All settings will revert to the factory settings.
NOTE
✎
When the factory default settings are restored, all
the user data stored in the BD data will be deleted.
▪
General
Background
Change the background theme of the menu screen.
Settings
Background
Dis
Au
Skin 1
Skin 2
Skin 3
Skin 4
Skin 5
Sy
N
La
Se
Ge
Su
' Return
ꢂꢂ
English
You can also update software in any of the two
ways as follows: Software update is the same as
in the By Internet menu.
Support
Software Upgrade
•
then download and store the latest software
(RUF file) into a USB flash drive. Connect
the USB flash drive to the USB port of the
player (disc tray must be empty) to update the
software, then follow the on-screen instructions.
This menu allows you to upgrade software
for performance improvements or additional
services. You can check the current software
version, upgrade using the internet and set the
Auto upgrade notification. If the player is properly
connected to the network by cable or wirelessly,
the player will automatically connect to Samsung’s
website each time it is turned on and download
update files if any valid upgrade exists.
•
CD/DVD : Visit www.samsung.com/
bluraysupport, download and write the latest
software (RUF file) onto a disc. Insert and play
the disc in the player to start the update, then
follow the on-screen instructions.
Settings
NOTE
✎
Display
Software Upgrade
Software upgrades using the USB Host jack must be
performed with no disc inside.
▪
▪
Software Upgrade
Audio
System
Network
Language
Security
General
Support
Current Version
: XXX-XXXXXXXXX
If you want to cancel the upgrade in the process of
downloading the upgrade data, press the ENTER
button.
By Internet
\
Auto Upgrade Notification : On
" Select ' Return
When the system upgrade is done, check the
▪
▪
software details in the software Upgrade menu.
Do not turn off the player during the System
Upgrade, as it may cause the player to not work
properly.
1. To select By Internet, press the ENTER
button.
Software upgrades using the USB Host jack must be
▪
A popup message will appear if an update is
performed with a USB memory flash stick only.
available.
2. If you select Yes, the player will turn off
automatically before restarting.
(Never turn it on manually.)
Contact Samsung
Provide contact information for assistance with
your player.
3. The update progress popup will appear.
When the update is completed, the player will
turn back off automatically.
4. Press the POWER button to turn on the
player.
NOTE
✎
The Update will be completed when the player turns
off after restarting. Press the POWER button to turn
on the updated player for your use.
▪
Never turn off or on the player manually during the
update process.
Samsung Electronics shall take no legal responsibility
for player malfunction caused an unstable internet
connection or consumer negligence during software
upgrade.
▪
English
ꢂꢃ
Basic Functions
Playing a Disc
Using the Disc menu/Title menu/
Popup menu
Playback
Using the Disc Menu
1. Press the OPEN/CLOSE (
) button to
open the disc tray.
hZ
2. Place a disc gently into the tray with the disc’s
1. During playback, press the DISC
label facing up.
MENU button on the remote control.
3. Press the OPEN/CLOSE (
) button to
2. Press the ▲▼◄► buttons to make
the desired selection, then press the
ENTER button.
close the disc tray.
4. Press the PLAY (
) button.
NOTE
Playback related buttons
✎
Depending on the disc, the menu items may differ
and this menu may not be available.
▪
PLAY (
STOP (
PAUSE (
)
Starts playback.
Stops playback.
Using the Title Menu
•
•
If pressing the button once : The
stop position will be memorized.
)
If pressing the button twice : The
Z
stop position will be not memorized.
1. During playback, press the TITLE
)
Pauses playback.
MENU button on the remote control.
2. Press the ▲▼◄► buttons to make
the desired selection, then press the
ENTER button.
NOTE
✎
For some discs, pressing the STOP (
) button
▪
once may not memorize the resume position.
NOTE
✎
Depending on the disc, the menu items may differ
and this menu may not be available.
▪
Disc Structure
The contents of disc are usually divided as below.
Playing the Title List
•
Blu-ray Disc, DVD-VIDEO
title 1
title 2
�
chapter 1 chapter 2 chapter 1 chapter 2 chapter 3
1. During playback, press the DISC
•
•
Audio CD (CD-DA)
MENU or TITLE MENU button.
track 1
track 2
track 3
track 4
track 5
file 3
2. Press the ▲▼ buttons to select an
entry you want to play from Title List,
then press the ENTER button.
MP3, WMA, DivX, MKV and MP4
NOTE
folder (group) 1
folder (group) 2
✎
file 1
file 2
file 1
file 2
If your disc has the playlist, press the GREEN(B)
▪
button to go to the Playlist.
ꢂꢄ
English
Using the Popup Menu
Skipping Chapters
h
h�Z��
)
•
During playback, press the SKIP (
1. During playback, press the POPUP
button.
MENU button on the remote control.
If you press the SKIP (
) button, it moves to
2. Press the ▲▼◄► buttons or ENTER
the next chapter.
button to select the desired menu.
If you press the SKIP (
) button, it moves to
NOTE
✎
the beginning of the chapter. One more press
makes it move to the beginning of the previous
chapter.
Depending on the disc, the menu items may differ
and this menu may not be available.
▪
Using the Search and Skip Functions
Slow Motion Play/Step Motion Play
During play, you can search quickly through a
chapter or track, and use the skip function to
jump to the next selection.
Slow Motion Play
h�Z��
)
Searching for a Desired Scene
h�Z��
•
In pause mode, press the SEARCH (
button.
If you press the SEARCH (
) button, the
•
During playback, press the SEARCH (
)
playback speed is reduced to
button.
*
1/8
*
1/4
*
1/2
Each time you press the SEARCH (
)
•
To return to normal speed playback, press the
button, the playback speed will change as follows.
PLAY (
) button.
NOTE
✎
BD-ROM,
)
)
1
)
)
2
)
)
3
BD-RE/-R,
DVD-RW/-R,
DVD+RW/+R,
DVD-VIDEO
No sound is heard during slow mode.
▪
4
5
6
)
(
7
7
(
(
1
(
(
2
(
(
3
4
5
6
Step Motion Play
)
(
1
)
(
2
)
(
3
DivX, MKV, MP4
h�Z��
) button.
1
2
3
•
In pause mode, press the PAUSE (
•
To return to normal speed playback, press the
Each time the PAUSE (
) button is pressed,
PLAY (
) button.
a new frame will appear.
•
To return to normal speed playback, press the
NOTE
✎
PLAY (
) button.
No sound is heard during search mode.
▪
NOTE
✎
No sound is heard during step mode.
▪
English
ꢂꢅ
Basic Functions
Repeat Playback
4. Press the ENTER button at the point where
you want repeat play to stop (B).
5. To return to normal play, press the REPEAT
Repeat the Title or Chapter
button again.
6. Press the ENTER button.
h�Z�
NOTE
✎
Repeat the disc title or chapter.
If you set point (B) before 5 seconds has lapsed, the
prohibition message will appear.
▪
Depending on the disc, the Repeat function may
not be available.
1. During playback, press the REPEAT
Using the TOOLS button
button on the remote control.
During playback, you can operate disc
menu by pressing the TOOLS button.
2. Press the ▲▼ buttons to select Chapter or
Title, then press the ENTER button.
•
Tools Menu Screen
Repeat
Chapter
>
Tools
Title
:
1/1
4/21
Chapter
Playing Time
Audio
<
:
>
00:12:06
:
:
:
1/7 ENG Multi CH
3. To return to normal play, press the REPEAT
Subtitle
Angle
1/6 ENG
1/1
button again.
BONUSVIEW Video :
BONUSVIEW Audio :
Picture Setting
Off
4. Press the ▲▼ buttons to select Off, the press
0/1 Off
the ENTER button.
< Change " Enter
Repeat the Section
NOTE
✎
h�Z�
Depending on the disc, the Tools menu may differ.
▪
1. During playback, press the REPEAT
button on the remote control.
Moving to a Desired Scene Directly
h�Z�
2. Press the ▲▼ buttons to select Repeat A-B.
1. During playback, press the TOOLS button.
Repeat
Repeat A-B : Off
" Mark A
>
2. Press the ▲▼ buttons to select Title, Chapter
or Playing Time.
3. Enter the desired Title, Chapter or Playing
Time using the number buttons, then press
the ENTER button.
3. Press the ENTER button at the point where
you want repeat play to start (A).
ꢂꢆ
English
NOTE
✎
Selecting the Audio Language
h�Z�
You can also operate this function by
pressing the AUDIO button on the
remote control.
Depending on the Blu-ray Disc / DVD, you may be
▪
able to change the desired subtitle in the Disc Menu.
Press the DISC MENU button.
This function depends on what subtitles are encoded
on the disc and may not be available on all Blu-ray
Discs/DVDs.
▪
A Blu-ray Disc can contain up to 255 subtitle
▪
▪
languages and a DVD up to 32.
1. During playback, press the TOOLS button.
Information about the main feature/BONUSVIEW
mode will also be displayed if the Blu-ray Disc has a
BONUSVIEW section.
2. Press the ▲▼ buttons to select Audio.
3. Press the ◄► buttons to select the desired
audio language.
This function changes both the primary and
▪
▪
▪
NOTE
✎
secondary subtitles at the same time.
The ◄► indicator will not be displayed on the
screen if the BONUSVIEW section does not contain
any BONUSVIEW audio settings.
▪
▪
The total number of subtitles is the sum of the
primary and secondary ones.
If you press the SUBTITLE button on the remote
Information about the main feature/BONUSVIEW
mode will also be displayed if the Blu-ray Disc has a
BONUSVIEW section.
control, the subtitle bar will be displayed.
Press the RETURN button to remove the subtitle bar.
Use the ◄► button to switch between main feature
and BONUSVIEW audio modes.
Changing the Camera Angle
This function depends on what audio languages are
encoded on the disc and may not be available.
▪
▪
▪
hZ
A Blu-ray Disc can contain up to 32 audio languages
When a Blu-ray Disc/DVD contains multiple angles
of a particular scene, you can use the ANGLE
function.
and a DVD up to 8.
Some Blu-ray Discs may allow you to select either
the multi-channel LPCM or Dolby digital audio
soundtrack in English.
1. During playback, press the TOOLS button.
2. Press the ▲▼ buttons to select Angle.
If you press the AUDIO button on the remote control,
▪
3. Press the ◄► buttons to select the desired
Audio bar will be displayed.
Angle.
Press the RETURN button to remove the Audio bar.
Selecting the Picture Setting
Selecting the Subtitle Language
hZ�
You can also operate this function by
pressing the SUBTITLE button on the
remote control.
h�Z�
This function enables you to adjust video quality
when you are connected to a TV via HDMI.
1. During playback, press the TOOLS button.
2. Press the ▲▼ buttons to select Picture Setting,
then press the ENTER button.
1. During playback, press the TOOLS button.
3. Press the ◄► buttons to select the desired
2. Press the ▲▼ buttons to select Subtitle.
Picture Setting, then press the ENTER button.
3. Press the ◄► buttons to select the desired
subtitle language.
English
ꢂꢇ
Basic Functions
•
•
•
•
Dynamic : Choose this setting to increase
Listening to Music
Sharpness.
Normal : Choose this setting for most
o�
viewing applications.
Buttons on the Remote Control
Movie : This is the best setting for watching
movies.
used for Music Playback
User : The user can adjust the sharpness
and noise reduction function respectively.
@
Setting BONUSVIEW
SUBTITLE
AUDIO
h
!
0
9
8
1
The BONUSVIEW feature allows you to view
additional content (such as commentaries) in a
small screen window while the movie is playing.
This function is only available if the disc has the
bonusview feature.
2
3
TOOLS
INFO
EXIT
You can also operate this function by
pressing the BONUSVIEW button on
the remote control.
4
RETURN
7
5
6
1. During playback, press the TOOLS button.
INTERNET@ FULL SCREEN REPEAT
2. Press the ▲▼ buttons to select BONUSVIEW
Video or BONUSVIEW Audio.
SEARCH buttons : Fast Play.
3. Press the ◄► buttons to select the desired
1
(Audio CD (CD-DA) only)
bonusview.
NOTE
PAUSE button : Pauses playback.
2
3
✎
If you switch from BONUSVIEW Video, BONUSVIEW
Audio will change automatically in accordance with
BONUSVIEW Video.
▪
PLAY button : Plays the currently selected track.
▲▼ buttons : Selects a track in the Music List or
4
5
6
7
Playlist.
Tools
YELLOW(C) button : Select or deselect a track in
BONUSVIEW Video <
BONUSVIEW Audio :
Picture Setting
Off
>
0/1 Off
the music list.
< Change " Enter
REPEAT button : Selects the play mode in the
Playlist.
ENTER button : Plays and pauses the selected
track.
◄► buttons : Jump Play.
8
9
(except for Audio CD (CD-DA))
STOP button : Stops a track.
SKIP button : During playback, moves to the next
page in the Music List or moves to the next track in
the Playlist.
0
ꢃ0
English
SKIP button : During playback, moves to the
previous page in the Music List or moves to the
previous track in the Playlist.
Shows the current play time/total play time.
Displays the current playback status
Displays the repeated playback status.
5
6
7
If you press this button after three seconds of
playback in the Playlist, the current track will be
replayed from the beginning. But, if you press this
button within three seconds after playback starts in
the Playlist, the previous track will be played.
!
@
2. Press the ▲▼ buttons to select the track
you want to play, and then press the ENTER
button.
NUMBER buttons : During the Playlist playback,
press the desired track number. The selected track
will be played.
Repeat an Audio CD (CD-DA)/MP3
1. During the Playlist playback, press the
REPEAT button.
2. Select the desired play mode by
Playing an Audio CD (CD-DA)/MP3
pressing the REPEAT button repeatedly.
1. Insert an Audio CD (CD-DA) or an MP3 Disc
Tracks on a disc are
into the disc tray.
Audio CD
played in the order in
•
For an Audio CD (CD-DA), the first track will
Off
(CD-DA)/MP3 which they were recorded
be played automatically.
on the disc.
•
For an MP3 disc, press the ◄► buttons
to select Music, then press the ENTER
button.
Audio CD
(
(
(
) Track
) One
) All
Current track is repeated.
(CD-DA)
MP3
Current track is repeated.
All tracks are repeated.
Audio CD (CD-DA)/MP3 Screen Elements
Audio CD
(CD-DA)/MP3
1
2
3
The random option plays
a disc’s track in random
order.
Audio CD
Playlist
1/6
(
) Shuffle
TRACK 001
(CD-DA)/MP3
TRACK 001
TRACK 002
TRACK 003
TRACK 004
TRACK 005
TRACK 006
05:57
04:27
04:07
03:41
03:17
7
6
Playlist
+
00:08 / 05:57
1. Insert an Audio CD (CD-DA) or an MP3 Disc
03:35
Return
into the disc tray.
Pause
Tools
"
'
•
For an Audio CD (CD-DA), the first track will
be played automatically.
5
4
•
For an MP3 disc, press the ◄► buttons
to select Music, then press the ENTER
button.
Displays the music information.
Displays the playlist.
1
2
3
4
2. To move to the Music List, press the STOP (
)
or RETURN button.
The Music List screen is displayed.
Display the current track/total tracks.
Displays buttons available.
English
ꢃ1
Basic Functions
3. Press the ▲▼◄► buttons to move desired
track, then press the YELLOW(C) button to
check desired tracks.
Playing back a Picture
G
Repeat this procedure to select additional
tracks.
Playing a JPEG Disc
Music TRACK 003
3 files selected 1/2 Page
1. Insert a JPEG disc into the disc tray.
2. Press the ◄► buttons to select the Photos,
TRACK 001
TRACK 002
00:05:57
00:04:27
and then press the ENTER button.
TRACK 003
00:04:07
TRACK 004
00:03:41
3. Press the ▲▼◄► buttons to select the folder
you want to play, and then press the ENTER
button.
TRACK 005
TRACK 006
00:03:35
00:03:17
TRACK 007
00:03:47
TRACK 008
00:03:49
TRACK 009
TRACK 010
00:03:45
00:03:53
4. Press the ▲▼◄► buttons to select the photo
you want to play, and then press the ENTER
button.
()
c
Select
Jump page ' Return
CDDA
The Slide Show starts automatically.
4. If there is an undesired track in the playlist,
press the YELLOW(C) button again.
The selected track will be deleted.
NOTE
✎
You can’t enlarge the subtitle and PG graphic in the
full screen mode.
▪
5. Press the ENTER button to play the selected
tracks.
Selected tract will automatically play.
Using the TOOLS button
Playlist
1/3
TRACK 001
TRACK 001
TRACK 002
TRACK 003
During the slide show playback, you
can use various function by pressing the
TOOLS button.
05:57
04:27
04:07
+
00:08 / 05:57
Tools
Stop Slide Show
Slide Show Speed :
Background Music
Zoom
Normal
Pause
Tools
Return
"
'
Rotate
Information
>Move "Enter 'Return
6. To go to the Music List, press the STOP (
)
or RETURN button.
7. To go to the Playlist, press the ENTER
button.
•
•
•
Stop Slide Show : Select this if you want to
NOTE
✎
stop the slide show.
You can create a playlist with up to 99 tracks on
Audio CD (CD-DA).
▪
Slide Show Speed : Select this if you want to
adjust the Slide Show speed.
Background Music : Select this if you want to
listen to music while viewing a picture.
ꢃꢀ
English
•
•
Zoom : Select this if you want to enlarge the
5. Press the ▲▼ buttons to select the USB,
current picture. (Enlarged up to 4 times)
then press the ENTER button.
Rotate : Select this if you to rotate the picture.
(This will rotate the picture either clockwise or
counter clockwise.)
6. Press the ◄► buttons to select the desired
Videos, Music or Photos, then press the
ENTER button.
•
Information : Shows the picture information
-1
4 . Press the BLUE(D) button.
including the name and size, etc.
NOTE
✎
Please activate Internet@TV service
to enjoy a variety of Internet Services.
To enable the Background Music function, both
music and MP3 files must be contained in the same
folder. However, the sound quality can be affected
by the bit rate of the MP3 file, the size of the photo
and the encoding method.
▪
USB
USB
d Home " Enter
Playing back a USB Storage Device
-1
5 . Press the ◄► buttons to select the USB,
You can use the USB connection to play multimedia
files (MP3, JPEG, DivX, etc) downloaded from the
USB storage device.
then press the ENTER button.
-1
6 . Press the ▲▼ buttons to select the desired
Videos, Music or Photos, then press the
1. Move to the home menu.
ENTER button.
2. In Stop mode, connect the USB storage
device to the USB port on the front panel of
the player.
7. For playing back Video, Music or Photo files,
refer to pages 50~53.
The message “Do you want to access the
NOTE
✎
device?” will be displayed.
You must remove the USB storage device safely
(by performing the “Safe to Remove USB” function)
in order to prevent a possible damage to the USB
memory. Press the MENU button to move to the
home menu, and select the YELLOW(C) button and
press the ENTER button.
▪
3. Press the ◄► button to select Yes, then
press the ENTER button.
4. Press the RED(A) button.
When the Audio-CD (CD-DA), MP3 and JPEG files are
in stop mode, you can’t see full screen by pressing
the FULL SCREEN button on the remote control.
▪
▪
Please activate Intern
e
t
@
T
V service
to enjoy a variety of Internet Services.
If you insert the disc when playing USB storage
device, the device mode is changed to “DVD or CD”
automatically.
CD
USB
USB a Change Device
c
Safely Remove USB
d
View Devices " Enter
English
ꢃꢁ
Basic Functions
Notes on USB connection
•
•
•
•
•
Supported devices: USB storage media, MP3 player, digital camera, USB card reader
Does not support if a folder or file name is longer than 128 characters.
A certain USB/digital camera device may not be compatible with the product.
FAT16, FAT32 and NTFS file systems are supported.
Connect directly to the product's USB port. Connecting through another cable may raise problems
with USB compatibility.
•
•
•
•
•
•
Inserting more than one memory device to a multi-card reader may not operate properly.
PTP protocol is not supported.
Do not disconnect USB device during a "loading" process.
Bigger the image resolution, the longer the delay to displaying.
DRM applied MP3 files downloaded from a commercial site are not played back.
External HDD device is not supported.
Supported file formats
video File Support
File Extension
Container
Video Codec
Audio Codec
Resolution
MP3
AC3
1920x1080
1920x1080
1920x1080
DivX 3.11/4.x/5.1/6.0
XviD
*.avi
DTS
AVI
MP4v3
WMA
1920x1080
H.264 BP/MP/HP
PCM
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
VC-1 AP
DivX 5.1/6.0
XviD
MP3
AC3
DTS
*.mkv
MKV
H.264 BP/MP/HP
VC-1 AP
*.wmv
*.mp4
WMA
AAC
WMV (wmv9)
MP4
VC-1 SM
MP4 (mp4v)
H.264 BP/MP/HP
MPEG1
MP1, 2
*.mpg
AC3
PS
MPEG2
*.mpeg
DTS
H.264 BP/MP/HP
Music File Support
File Extension
*.mp3
Container
Audio Codec
Support Range
MP3
-
MP3
Compliant with WMA version 10
*.wma
WMA
* Sampling rates (in kHz) - 8, 11, 16, 22, 32, 44.1, 48
* Bit rates - All bit-rates in the range 5kbps to 384kbps
WMA
ꢃꢂ
English
Network Services
You can enjoy various network services such as
Internet@TV or BD-LIVE by connecting the player
to the network system.
4. When you have agreed on the service
agreement, the Internet@TV service will start
being updated. It takes several minutes.
When the update is completed, you will see
the Internet@TV menu screen.
Check the following instructions before using
any network service.
Internet@TV at a Glance
1. Connect the player to the network.
(See pages 28~29)
2. Configure the network settings.
1
2
3
(See pages 39~43)
Recommended
My Applications
Using Internet@Tv
by Date 1/3
Connect this player to the network to download
various for a fee or free-of-charge applications.
Internet@TV brings useful and entertaining content
and services directly from the web to your player
such as news, weather forecasts, stock market
quotes, games, movies and music.
Samsung Apps Settings
a
Login
b
Mark as Favourite
d
Sort by ' Return
6
5
4
You can also operate this function by
pressing the INTERNET@ button on
the remote control.
Commercial : Displays Internet@TV Guide, product
1
introduction and new application introduction.
Getting Started with Internet@TV
Recommended : Displays recommended contents
2
3
managed by Samsung.
1. Move to the home menu.
My Applications : Displays your personal gallery
which can be added and deleted by you.
Please activate Intern
e
t
@
T
V service
Navigation Help : Displays remote control buttons
to enjoy a variety of Internet Services.
available.
•
•
•
•
RED(A) : To log in to Internet@TV.
4
GREEN(B) : To mark the application as a favorite.
BLUE(D) : To sort the applications.
Return : To return to the previous menu.
No Disc
a Change Device
d View Devices " Enter
Settings : You can set the system setup and create
5
6
accounts, etc.
2. Press the ◄► buttons to select Internet@TV
Samsung Apps : You can download various
and press the ENTER button.
chargeable or free-of-charge application services.
3. In the start screen of the Internet@TV service,
you will see the service agreement screen.
You should agree to the service terms and
conditions before you can use the Internet@
TV service.
English
ꢃꢃ
Network Services
12. Press buttons on the remote to input the rest
Using the Keypad
of ‘Challenger Rd., Ridgefield Park NJ’.
Through your remote, you can use the On-Screen
Keypad in several Internet@TV applications to enter
text.
13. Press the ENTER button.
14. The map and address appear on the screen.
Pressing the SUBTITLE button on the remote while
you are using the Screen Keypad lets you change
the text fields to lower case, upper case, numbers
and icons.
NOTE
✎
Samsung Electronics shall take no legal responsibility
for any interruption of the Internet@TV service
caused by the service provider for any reasons.
▪
▪
The Internet@TV service is to download and process
data via the Internet so that you can enjoy the
contents on the TV screen.
1
4
7
2
5
8
0
abc
jkl
tuv
3
6
9
def
mno
wxyz
ghi
pqrs
If the Internet connection is unstable, the service
may be delayed or interrupted.
Input Mode
Delete
Furthermore, the player may be turned off automatically.
If this is the case, check the Internet connection and
try again.
a
A
1
The application service may be provided in English
only and the contents available may vary, depending
on the area.
▪
For example, here is how to search an address in
Google Maps:
When using a application service, you can not
1. Press the ENTER button on the remote at the
▪
▪
▪
▪
▪
operate FULL SCREEN button on the remote control.
Google Maps icon at the Internet@TV.
For more information about the Internet@TV service,
visit the web site of the applicable service provider.
2. Press GREEN(B) button to use the SEARCH
function.
The provided services are subject to change,
3. Press the ◄► buttons to move to the “Search
depending on the Internet@TV service provider.
or address” window.
The Internet@TV service contents may differ
according to the firmware version.
4. Press the ENTER button to use Search or
address function.
For-a-fee DivX contents with copy protection can
5. For example, suppose that you want to input
only be played using HDMI cable.
‘105 Challenger Rd., Ridgefield Park NJ’.
If you have connected your player to your TV using
Component or video cables, the DivX video signal
can not output or the popup message “Connect
with a HDMI cable to play this file.” or “Cannot play
current file.” will be displayed.
6. Press the SUBTITLE button on the remote
twice to change the input mode from lower
case to numbers.
7. Press ‘1’, ‘0’, ‘5’.
8. Press the YELLOW(C) button on the remote
to input a blank space.
9. Press the SUBTITLE button on the remote
3 times to change the input mode from
numbers to upper case.
10. Press ‘2’ button on the remote 3 times to
input C.
11. Press the SUBTITLE button on the remote 3
times to change the input mode from upper
case to lower case.
ꢃꢄ
English
Account Login
System Setup
For a more enjoyable application experience,
register and log in to your account.
Reset
To do this, you must create an account first.
(For instructions on creating an account, refer to
Internet@TV ID on this page)
Resets Internet@TV settings to factory default
settings.
1. Press the ▲▼◄► buttons to select the
desired application and press the RED(A)
button.
NOTE
✎
If you forgot your password, press the STOP (
)
▪
button on the front panel of the player for more than
5 seconds with no disc inserted.
Recommended
Login
Internet@TV ID
by Date 1/3
Use this menu to create or delete an account and
enter or delete account information.
User account :
aaa
Password :
You can control your account including contents
site’s account information.
a
Create [0~9] Enter PIN ' Cancel
This account is only for Internet@TV.
Samsung Apps Settings
a
Login
b
Mark as Favourite
d
Sort by ' Return
Create
Create an account and link it with desired service
applications.
2. Enter the user account and password.
Settings
NOTE
✎
Create IDs and configure Internet@TV settings
from this screen.
The account name must be at least 1 character in
length but no more than 8.
▪
▪
You can register up to 10 User Account Names.
Settings
Manager
. System setup
. Internet@TV ID
. Service Manager
. Properties
Change the Service Lock password
Reset
•
•
•
Service Site : Register login information for
service sites.
Change Password : Change account
password.
Delete : Delete the account.
' Return
English
ꢃꢅ
Network Services
Using the color buttons with the Samsung
Apps
Service Manager
Delete and lock applications installed to Internet@
•
•
•
RED(A) (Login) : To log in to the internet
TV.
service.
GREEN(B) (Thumbnail View) : To change the
Lock
view mode.
Lock the application. Accessing a locked
application requires the password.
BLUE(D) (Sort By) : To sort the applications by
Featured, Most Downloaded, Most Recent or
Name.
Delete
Delete the application.
Internet@TV Services Available
•
YouTube/Pandora/Netflix/Blockbuster/USA
Today News
Properties
Display information about Internet@TV. Use the
“Check the speed of your internet connection”
option to test your network connection.
-
-
-
Blockbuster : You can view movies streamed
by Blockbuster.
YouTube : You can view video streamed by
YouTube.
Samsung Apps
Netflix : You can view movies streamed by
Netflix.
Various applications are available from here,
organized into different categories. Some
applications have a download fee.
-
-
Pandora : You can listen to Internet radio.
USA Today News : You can read news
streamed by USA Today News.
Samsung Apps
Video
1/1
Name
-
AccuWeather : You can view weather
information by AccuWeather.
Featured
Most downloaded
Most recent
What's New?
Video
YouTube
NOTE
Free
✎
Game
TV store Test User002
Sports
The available Internet contents services may be
added or deleted.
▪
Lifestyle
Information
Other
My page
Help
a
Login
b
Thumbnail View
d
Sort By ' Return
My page
Displays the application list.
Help
If you questions about Internet@TV, check this
section first. If none of the tips apply, please visit
the help website.
ꢃꢆ
English
BD-LIvE™
Using the AllShare Function
Once the player is connected to the network, you
can enjoy various movie-related service contents
using a BD-LIVE compliant disc.
AllShare enables you to play music, video and
photo files in your PC using the player.
To use AllShare, you must connect the player to
your PC via the network (See pages 28~29) and
install the SAMSUNG PC Share Manager on the
PC.
1. Check the size of the remaining memory.
The memory device must have at least 1GB
of free space to accommodate the BD-LIVE
services.
com.
2. Insert a Blu-ray disc that supports BD-LIVE.
2. Download the SAMSUNG PC Share Manager
3. Select an item from various BD-LIVE service
and install it on the PC.
contents provided by the disc manufacturer.
3. When the installation is completed, you will
see the SAMSUNG PC Share Manager icon
on your desktop.
NOTE
✎
The way you use BD-LIVE and the provided contents
may differ, depending on the disc manufacturer.
▪
Double-click the icon to launch the application.
Application Program at a Glance
Software Upgrade Notification
In network connection, the player will notice you of
6
1
any new software version with a popup message.
SAMSUNG PC Share Manager
File Share Server Help
1. Turn on the player.
Server : PC Share Manager
2 3 4 5
2. From the Software Upgrade menu, set Auto
Upgrade Notification to On. (See page 45)
If there is a new software version available, the
player will notice you with a popup message.
My Computer
Shared Folder
C: Document and settings Admin
Folder
Full Path
Folder 1
C: Document and settin..
Name
Size
Kind
Folder 1
File
Folder 2
Folder 3
File
File
3. To upgrade the firmware, select Yes.
It will turn off automatically before restarting.
(Never turn it on manually.)
4. The update progress popup will appear.
When the update is completed, it will turn
back off automatically.
8
7
Menu Bar
1
2
5. Press the POWER button to turn on the
player.
Share Folder Enabled icon : Use this if you want to
select a folder in your PC to share.
NOTE
✎
Share Folder Disabled icon : Use this if you want
Update will be completed when the player turns off
after restarting. Press the POWER button to turn on
the updated player for your use.
▪
3
4
to set folder sharing off.
Refresh icon : Use this if you want to refresh list of
Never turn off or on the player manually during the
update process.
folders and files in My Computer.
Set Change State icon : Select a folder to share
Samsung Electronics shall take no legal responsibility
for player malfunction caused by unstable of internet
connection or consumer negligence during software
upgrade.
▪
and don’t forget to press this button.
5
6
The updated state will be applied to the server.
Server : Displays the name of the sharing server.
English
ꢃꢇ
Network Services
NOTE
✎
Shared Folder : Displays a list of the shared folders.
7
Depending on the performance of the external
▪
▪
▪
My Computer : Displays a list of the folders and
modem or router, HD video may not play properly.
8
files in the PC.
If your system uses a firewall, the player may not
locate your PC on the TV screen.
4. Select a folder to share from the My computer
pane, and click the Share Folder Enabled
icon ).
AllShare does not support the following functions.
-
-
The Background Music and Background Music
Setting functions.
(To remove a shared folder : Select a folder to
remove from the shared folders, and click the
Share Folder Disabled icon ).)
Sorting files by preference in the Photo, Music,
and Movie folders.
5. To apply the updated sharing state to the
-
-
The Change Group function.
The Safe Remove function.
server, click the Set Change State icon ).
The Sorting method may differ depending on the
6. To enable the player to locate a PC server,
click Share from the menu bar.
▪
▪
▪
sever function.
Click Set Device Policy and click Accept.
The search and skip operation may differ depending
on the sever function.
SAMSUNG PC Share Manager
File Share Server Help
If you press the STOP (
) button during video
Server : PC Share Manager
Set Device Policy
playback, stop position will be memorized and it will
be memorized only end user’s operation.
But stop position will not be memorized depending
on the sever function.
My Co
Delete
Item
C:
IP
Device
State
SSeetleScttaedte
ettin..
Na
XXX.XXX.X.XX
SAMSUNG Blu-ray Disc Player Deny
Accept
F
F
F
During video playback, play time will not display.
▪
▪
OK
Cancel
To use AllShare function, please locate both this
player and PC in same subnet.
7. Click the Set Change State icon ) and
move to the home menu on player.
8. To select a device, use the RED(A) or BLUE(D)
button to select a file to play.
(For playing back Video, Music or Photos files,
see pages 50~53.)
Please activate Intern
e
t
@
T
V service
to enjoy a variety of Internet Services.
No Disc
a Change Device
d View Devices " Enter
ꢄ0
English
Appendix
Troubleshooting
Before requesting service, please check the following.
PROBLEM
SOLUTION
No operation can be performed with the
•
•
•
Check the batteries in the remote control. They may need replacing.
Operate the remote control at a distance of no more than 20 feet.
remote control.
Remove batteries and hold down one or more buttons for several minutes
to drain the microprocessor inside the remote control to reset it. Reinstall
batteries and try to operate the remote control again.
Disc does not play.
•
•
Ensure that the disc is installed with the label side facing up.
Check the region number of the Blu-ray Disc/DVD.
Disc Menu does not appear.
•
Ensure that the disc has disc menus.
The prohibition message appears on the
screen.
•
•
•
This message appears when an invalid button is pressed.
The Blu-ray Disc/DVD’s software doesn’t support the feature (e.g., angles)
You’ve requested a title or chapter number or search time that is out of
range.
Play mode differs from the Setup Menu
selection.
•
Some of the functions selected in the Setup Menu may not work properly if
the disc is not encoded with the corresponding function.
The screen ratio cannot be changed.
•
•
The Screen Ratio is fixed on your Blu-ray Disc/DVDs.
This is not a problem with the player.
No audio.
•
Make sure you have selected the correct Digital Output in the Audio Options
Menu.
The screen is blocked
•
•
•
If the HDMI output is set to a resolution your TV cannot support (for
example, 1080p), you may not see a picture on your TV.
Press the STOP (
) button (on front panel) for more than 5 seconds with
no disc inside. All settings will revert to the factory settings.
When the factory default settings are restored, all the user data stored in
the BD data will be deleted.
English
ꢄ1
Appendix
PROBLEM
SOLUTION
Forgot password
•
Press the STOP (
) button (on front panel) for more than 5 seconds with
no disc inside. All settings including the password will revert to the factory
settings.
Don’t use this unless absolutely necessary.
•
•
When the factory default settings are restored, all the user data stored in
the BD data will be deleted.
If you experience other problems.
Go to the contents and find the section of the user manual that contains the
explanations regarding the current problem, and follow the procedure once
again.
•
If the problem still cannot be solved, please contact your nearest Samsung
authorized service center.
The picture is noisy or distorted
No HDMI output.
•
•
Make sure that the disc is not dirty or scratched.
Clean the disc.
•
•
Check the connection between the TV and the HDMI jack of the player.
Check if your TV supports 480p, 720p, 1080i, 1080p HDMI input resolution.
Abnormal HDMI output screen.
•
If random noise appears on the screen, it means that TV does not support
HDCP (High-bandwidth Digital Content Protection).
PC Share Manager function
I can see folders shared through the PC
•
Since it shows only files corresponding to the Image, Music, and Movie
categories, files that do not correspond to these categories may not be
displayed.
Share Manager, but I cannot see the files.
AllShare function
Video is played intermittently.
•
•
Check if the network is stable.
Check if the network cable is properly connected and if the network is not
overloaded.
•
Wireless connection between the server and the player is unstable.
Check the connection.
AllShare connection between TV and PC is
unstable.
•
•
IP address under the same subnetwork should be unique, otherwise IP
collision can results in such a phenomenon.
Check if you have a firewall enabled.
If so, disable the firewall function.
ꢄꢀ
English
PROBLEM
BD-LIVE
SOLUTION
I cannot connect to the BD-LIVE server.
•
•
•
Check whether the network connection is successful or not by using
Network Test menu. (See page 43)
Check whether the USB memory device is connected with player
or not.
The memory device must have at least 1GB of free space to accommodate
the BD-LIVE service.
You can check the available size in BD Data Management. (See page 38)
•
•
Please check whether the BD-LIVE Internet Connection menu is set to
Allow(All).
If all above fails, contact the contents provider or update the latest
firmware.
When using the BD-LIVE service, an error
occurs.
•
The memory device must have at least 1GB of free space to accommodate
the BD-LIVE service.
You can check the available size in BD Data Management. (See page 38)
NOTE
✎
When the factory default settings are restored, all the user data stored in the BD data will be deleted.
▪
Viewing using 3D function
IMPORTANT HEALTH AND SAFETY INFORMATION FOR 3D PICTURES.
Read and understand the following safety information before using the 3D function.
•
Some viewers may experience discomfort while viewing 3D TV such as dizziness, nausea and
headaches.
If you experience any such symptom, stop viewing 3D TV, remove 3D Active Glasses and rest.
•
•
•
•
Watching 3D images for an extended period of time may cause eye strain. If you feel eye strain, stop
viewing 3D TV, remove your 3D Active Glasses and rest.
A responsible adult should frequently check on children who are using the 3D function. If there are any
reports of tired eyes, headaches, dizziness, or nausea, have the child stop viewing 3D TV and rest.
Do not use the 3D Active Glasses for other purposes (such as general eyeglasses, sunglasses,
protective goggles, etc.)
Do not use the 3D function or 3D Active Glasses while walking or moving around. Using the 3D
function or 3D Active Glasses while moving around may result in injuries due to running into objects,
tripping, and/or falling.
English
ꢄꢁ
Appendix
Index
J
T
A
JPEG
52~53
TV Aspect
Title Menu
Tools Menu
33
46
Accessories
Ad-hoc
15
29
M
48~50
Anynet+ (HDMI-CEC)
Audio Language
AllShare
38
49
Movie Frame (24F)
MP3
35
U
59~60
50~52
USB Storage Device
53
29, 41~43
53
B
N
W
BD Wise
33
38
Network Setup
39~43
33~34
BD Data Management
BD-LIVE
Wireless Network
43, 59
50
O
BONUSVIEW
Background Music
Z
Optimal Resolution
52
Zoom
P
C
PCM Downsampling
Popup Menu
36~37
47
Component
23
28
49
Cable Network
Camera Angle
Picture Setting
49~50
R
D
Region Code
Romote Control Sensor
Romote Control
Resolution
14
16
Digital Output
35~36
37
Dynamic Range Control
Downmixing Mode
DTS Neo:6
19
37
33
37
Repeat
48, 51
DST (Daylight Saving Time) 39
DivX
39
46
46
S
Disc Menu
Disc Structure
Supported File Format
Software Upgrade
Search and Skip
Slow and Step
13
45, 59
47
H
47
HDMI
21, 37
Subtitle Language
Slide Show
49
HDMI Supported Amplifier 25
52
HDMI Deep Color
35
SAMSUNG PC Share
Manager
59~60
I
Internet@TV
38, 55~58
30, 38
Initial Settings
ꢄꢂ
English
Specifications
Power Requirements
Power Consumption
Weight
AC 120V, 60Hz
14W
4 Ibs
General
Disc
Dimensions
17 (W) X 8.8 (D) X 1.7 (H) inches
+41°F to +95°F
Operating Temperature Range
Operating Humidity Range
BD (Blu-ray Disc)
10 % to 75 %
Reading Speed : 4.917 m/sec
Reading Speed : 3.49 ~ 4.06 m/sec.
Approx. Play Time (Single Sided, Single Layer Disc) : 135 min.
Reading Speed : 4.8 ~ 5.6 m/sec.
Maximum Play Time : 74 min.
Reading Speed : 4.8 ~ 5.6 m/sec.
Maximum Play Time : 20 min.
1 Channel : 1.0 Vp-p (75Ω load)
Blu-ray/DVD Disc : 480i
DVD (Digital Versatile Disc)
CD : 5 inches (COMPACT DISC)
CD : 3 1/2 inches (COMPACT DISC)
Composite Video
Y : 1.0 Vp-p (75Ω load)
PR : 0.70 Vp-p (75Ω load)
PB : 0.70 Vp-p (75Ω load)
Blu-ray Disc : 1080i, 720p, 480p, 480i
DVD : 480p, 480i
Video Output
Video/Audio
Component Video
HDMI
2D : 1080p, 1080i, 720p, 480p
3D : 1080p, 720p
PCM multichannel audio, Bitstream audio
2 Channel
L(1/L), R(2/R)
7.1 Channel
F/L, F/R, R/L, R/R, C/T, S/W, SBR, SBL
Digital Audio Output
Optical
48 kHz Sampling : 4 Hz to 22 kHz
Audio Output
*Frequency Response
96 kHz Sampling : 4 Hz to 44 kHz
*S/N Ratio
*Dynamic Range
*Total Harmonic Distortion
110 dB
100 dB
0.003%
*: Nominal specification
-
-
Design and specifications are subject to change without prior notice.
Weight and dimensions are approximate.
English
ꢄꢃ
Appendix
Compliance and Compatibility Notice
NOT ALL discs are compatible
•
Subject to the restrictions described below and those noted throughout this Manual, including the Disc
Type and Characteristics section of this user manual, disc types that can be played are: pre-recorded
commercial BD-ROM, DVD-VIDEO, and Audio CD (CD-DA) discs; BD-RE/-R, DVD-RW/-R discs; and
CD-RW/-R discs.
•
•
Discs other than the above cannot and/or is not intended to be played by this player. And some of the
above discs may not play due to one or more reasons provided below.
Samsung cannot assure that this player will play every disc bearing the BD-ROM, BD-RE/-R,
DVD-VIDEO, DVD-RW/-R, DVD+RW/+R and CD-RW/-R logos, and this player may not respond to
all operating commands or operate all features of every disc. These and other disc compatibility and
player operation issues with new and existing format discs are possible because:
-
Blu-ray is a new and evolving format and this player may not operate all features of Blu-ray Discs
because some features may be optional, additional features may have been added to the Blu-ray
Disc format after the production of this player, and certain available features may be subject to
delayed availability;
-
-
-
not all new and existing disc format versions are supported by this player;
new and existing disc formats may be revised, changed, updated, improved and/or supplemented;
some discs are produced in a manner that allows specific or limited operation and feature during
playback;
-
-
some features may be optional, additional features may have been added after the production of this
player or certain available features may be subject to delayed availability;
some discs bearing the BD-ROM, BD-RE/-R, DVD-VIDEO, DVD-RW/-R, DVD+RW/+R and
CD-RW/-R logos may still be non-standardized discs;
-
-
some discs may not be played depending on their physical state or recording conditions;
problems and errors can occur during the creation of Blu-ray Disc, DVD software and/or the
manufacture of discs;
-
-
this player operates differently than a standard DVD player or other AV equipment; and/or
for reasons noted throughout this user manual and for other reason(s) discovered and posted by
SAMSUNG customer care center.
•
•
If you encounter disc compatibility or player operation problems, please contact SAMSUNG customer care
center.
You may also contact SAMSUNG customer care center for possible updates on this player.
For additional information on playback restrictions and disc compatibility, refer to the Precautions,
Before Reading the user manual, Disc Types and Characteristics, and Before Playing sections of this
user manual.
Copy Protection
•
Because AACS (Advanced Access Content System) is approved as content protection system for
Blu-ray Disc format, similar to use of CSS (Content Scramble System) for DVD format, certain
restrictions are imposed on playback, analog signal output, etc., of AACS protected contents.
The operation of this product and restrictions on this product may vary depending on your time of
purchase as those restrictions may be adopted and/or changed by AACS after the production of this
product. Furthermore, BD-ROM Mark and BD+ are additionally used as content protection system for
Blu-ray Disc format, which imposes certain restrictions including playback restrictions for BD-ROM
Mark and/or BD+ protected contents. To obtain additional information on AACS, BD-ROM Mark, BD+,
or this product, please contact SAMSUNG customer care center.
ꢄꢄ
English
•
Many Blu-ray Disc/DVD discs are encoded with copy protection. Because of this, you should only
connect your Player directly to your TV, not to a VCR. Connecting to a VCR results in a distorted
picture from copy-protected Blu-ray Disc/DVD discs.
•
•
This item incorporates copy protection technology that is protected by U.S. patents and other
intellectual property rights of Rovi Corporation. Reverse engineering and disassembly are prohibited.
Under the U.S. Copyright laws and Copyright laws of other countries, unauthorized recording, use,
display, distribution, or revision of television programs, videotapes, Blu-ray Discs, DVDs, and other
materials may subject you to civil and/or criminal liability.
•
For Blu-ray Disc Player progressive scan output : CONSUMERS SHOULD NOTE THAT NOT
ALL HIGH DEFINITION TELEVISION SETS ARE FULLY COMPATIBLE WITH THIS PRODUCT AND
MAY CAUSE ARTIFACTS TO BE DISPLAYED IN THE PICTURE. IN CASE OF PROGRESSIVE SCAN
PICTURE PROBLEMS, IT IS RECOMMENDED THAT THE USER SWITCH THE CONNECTION TO
THE ‘STANDARD DEFINITION’ OUTPUT. IF THERE ARE QUESTIONS REGARDING OUR TV SET
COMPATIBILITY WITH THIS PRODUCT, PLEASE CONTACT OUR CUSTOMER SERVICE CENTER.
Network Service Disclaimer
All content and services accessible through this device belong to third parties and are protected by
copyright, patent, trademark and/or other intellectual property laws. Such content and services are
provided solely for your personal noncommercial use. You may not use any content or services in a
manner that has not been authorized by the content owner or service provider. Without limiting the
foregoing, unless expressly authorized by the applicable content owner or service provider, you may
not modify, copy, republish, upload, post, transmit, translate, sell, create derivative works, exploit, or
distribute in any manner or medium any content or services displayed through this device.
THIRD PARTY CONTENT AND SERVICES ARE PROVIDED “AS IS.” SAMSUNG DOES NOT WARRANT
CONTENT OR SERVICES SO PROVIDED, EITHER EXPRESSLY OR IMPLIEDLY, FOR ANY PURPOSE.
SAMSUNG EXPRESSLY DISCLAIMS ANY IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED
TO, WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. SAMSUNG
DOES NOT GUARANTEE THE ACCURACY, VALIDITY, TIMELINESS, LEGALITY, OR COMPLETENESS
OF ANY CONTENT OR SERVICE MADE AVAILABLE THROUGH THIS DEVICE AND UNDER NO
CIRCUMSTANCES, INCLUDING NEGLIGENCE, SHALL SAMSUNG BE LIABLE, WHETHER IN
CONTRACT OR TORT, FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL
DAMAGES, ATTORNEY FEES, EXPENSES, OR ANY OTHER DAMAGES ARISING OUT OF, OR IN
CONNECTION WITH, ANY INFORMATION CONTAINED IN, OR AS A RESULT OF THE USE OF ANY
CONTENT OR SERVICE BY YOU OR ANY THIRD PARTY, EVEN IF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES.
Third party services may be terminated or interrupted at any time, and Samsung makes no representation
or warranty that any content or service will remain available for any period of time. Content and services
are transmitted by third parties by means of networks and transmission facilities over which Samsung
has no control. Without limiting the generality of this disclaimer, Samsung expressly disclaims any
responsibility or liability for any interruption or suspension of any content or service made available
through this device.
Samsung is neither responsible nor liable for customer service related to the content and services.
Any question or request for service relating to the content or services should be made directly to the
respective content and service providers.
English
ꢄꢅ
Appendix
License
•
•
Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol
are trademarks of Dolby Laboratories.
Manufactured under license under U.S. Patent #’s : 5,451,942; 5,956,674; 5,974,380;
5,978,762; 6,226,616; 6,487,535; 7,212,872; 7,333,929; 7,392,195; 7,272,567
& other U.S. and worldwide patents issued & pending. DTS and the Symbol are
registered trademarks, & DTS-HD, DTS-HD Master Audio, and the DTS logos are
trademarks of DTS, Inc. Product includes software. © DTS, Inc. All Rights Reserved.
®
•
•
ABOUT DIVX VIDEO : DivX is a digital video format created by DivX,Inc. This is an official
software tools to convert your files into DivX video.
®
ABOUT DIVX VIDEO-ON-DEMAND : This DivX Certified device must be registered in order to play
DivX Video-on-Demand (VOD) content. To generate the registration code, locate the DivX VOD section
in the device setup menu. Go to vod.divx.com with this code to complete the registration process and
learn more about DivX VOD.
•
•
DivX Certified to play DivX video up to HD 1080p, including premium content.
The product unit accompanying this user manual is licensed under certain intellectual property rights of
certain third parties. This product is covered by one or more of the following U.S. patents : 5,457,669
5,561,649 5,705,762 6,043,912 6,438,099 6,467,061 6,556,521 6,578,163 6,697,307 6,728,474
6,771,891 6,894,963 6,895,593 6,937,815 6,996,327 7,009,926 7,085,221 7,088,649 7,092,327
7,099,566 7,123,564 7,142,493 7,142,495 7,145,861 7,146,624 7,151,729 7,161,879 7,164,647
7,167,437 7,173,891 7,177,250 7,194,187 7,203,891 7,209,423 7,210,067 7,228,062 7,245,566
7,245,567 7,257,065 7,263,045 7,269,110 7,272,086 7,272,106 7,280,460 7,283,729 7,286,454
7,304,938
•
•
This license is limited to private non-commercial use by end-user consumers for licensed contents.
No rights are granted for commercial use. The license does not cover any product unit other than this
product unit and the license does not extend to any unlicensed product unit or process conforming to
ISO/IEC 11172-3 or ISO/IEC 13818-3 used or sold in combination with this product unit.
The license only covers the use of this product unit to encode and/or decode audio files conforming to
the ISO/IEC 11172-3 or ISO/IEC 13818-3. No rights are granted under this license for product features
or functions that do not conform to the ISO/IEC 11172-3 or ISO/IEC 13818-3.
Open Source License Notice
-
In the case of using open source software, Open Source Licenses are available on the product
menu.
ꢄꢆ
English
LIMITED WARRANTY TO ORIGINAL PURCHASER
This SAMSUNG brand product, as supplied and distributed by SAMSUNG ELECTRONICS AMERICA, INC. (SAMSUNG) and
delivered new, in the original carton to the original consumer purchaser, is warranted by SAMSUNG against manufacturing
defects in materials and workmanship for the following limited warranty period:
One (1) Year Parts / Ninety Days (90) Labor
This limited warranty begins on the original date of purchase, and is valid only on products purchased and used in the United
States, and does not include transportation, installation, removal or reinstallation. Warranty repairs must be performed by
SAMSUNG’s authorized service center. To receive warranty service, the original dated bill of sale must be presented upon
request as proof of purchase to SAMSUNG or SAMSUNG’s authorized service center. Transportation to and from the service
center is the responsibility of the purchaser.
SAMSUNG will repair or replace this product, at our option and at no charge with new or reconditioned parts, if found to be
defective during the limited warranty period specified above. The product must be returned during the warranty period with
transportation charges prepaid to SAMSUNG’s designated service center. Prior to returning any product for warranty service,
the purchaser must contact SAMSUNG for problem determination and service procedures. SAMSUNG does not warrant
uninterrupted or error-free operation of the product.
All replaced parts and products become the property of SAMSUNG and must be returned to SAMSUNG. Replacement parts and
products assume the remaining original warranty, or ninety (90) days, whichever is longer.
This limited warranty covers manufacturing defects in materials and workmanship encountered in normal, noncommercial use
of this product and shall not apply to the following, including, but not limited to: damage which occurs in shipment; applications
and uses for which this product was not intended; failures or problems which are caused by products or equipment not supplied
by SAMSUNG; accidents, misuse, abuse, neglect, misapplication, fire, water, lightning or other acts of nature; incorrect electrical
line voltage, fluctuations or surges; damage caused by improper or faulty installation; improper connection with any peripheral;
product alteration or modification; improper or unauthorized repair; cosmetic damage or exterior finish; product with altered serial
numbers; failure to follow operating instructions, customer adjustments, maintenance and environmental instructions that are
covered and prescribed in the instruction book; use of non-SAMSUNG or unauthorized parts, supplies, accessories or equipment
which damage this product or result in service problems; failures or problems due to incompatibility with other equipment.
No person, agent, distributor, dealer or company is authorized to change, modify or extend the terms of these warranties in any
manner whatsoever. The time within which an action must be commended to enforce any obligations of SAMSUNG arising under
the warranty or under any statute, or law of the United States or of any state thereof, is hereby limited to ninety (90) days from the
date you discovered or should have discovered the defect. This limitation does not apply to implied warranties arising under state
law, if any.
SAMSUNG does not warrant (i) disc compatibility with new and existing format discs or (ii) error free playback in full compliance
with specifications of the compatible disc formats, and SAMSUNG shall not be liable for any data loss recorded in your discs.
SAMSUNG’s responsibility shall be limited to appropriate warranty services during the warranty period through SAMSUNG
customer care center. If you encounter compatibility or data loss problems, please contact SAMSUNG customer care center.
THERE ARE NO EXPRESS WARRANTIES OTHER THAN THOSE LISTED AND DESCRIBED ABOVE, AND NO WARRANTIES
WHETHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE, SHALL APPLY AFTER THE EXPRESS WARRANTY PERIODS STATED
ABOVE, AND NO OTHER EXPRESS WARRANTY OR GUARANTY GIVEN BY ANY PERSON, FIRM OR CORPORATION WITH
RESPECT TO THIS PRODUCT SHALL BE BINDING ON SAMSUNG. SAMSUNG SHALL NOT BE LIABLE FOR LOSS OF
REVENUE OR PROFITS, FAILURE TO REALIZE SAVINGS OR OTHER BENEFITS, OR ANY OTHER SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES CAUSED BY THE USE, MISUSE OR INABILITY TO USE THIS PRODUCT, REGARDLESS OF
THE LEGAL THEORY ON WHICH THE CLAIM IS BASED, AND EVEN IF SAMSUNG HAS BEEN ADVISED OF THE POSSIBILITY
OF SUCH DAMAGES. NOR SHALL RECOVERY OF ANY KIND AGAINST SAMSUNG BE GREATER IN AMOUNT THAN THE
PURCHASE PRICE OF THE PRODUCT SOLD BY SAMSUNG AND CAUSING THE ALLEGED DAMAGE. WITHOUT LIMITING
THE FOREGOING, PURCHASER ASSUMES ALL RISK AND LIABILITY FOR LOSS, DAMAGE OR INJURY TO PURCHASER AND
PURCHASER’S PROPERTY AND TO OTHERS AND THEIR PROPERTY ARISING OUT OF THE USE, MISUSE OR INABILITY
TO USE THIS PRODUCT SOLD BY SAMSUNG NOT CAUSED DIRECTLY BY THE NEGLIGENCE OF SAMSUNG. THIS
LIMITED WARRANTY SHALL NOT EXTEND TO ANYONE OTHER THAN THE ORIGINAL PURCHASER OF THIS PRODUCT, IS
NONTRANSFERABLE AND STATES YOUR EXCLUSIVE REMEDY.
Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental or
consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights,
and you may also have other rights which vary from state to state.
To obtain warranty service, please contact SAMSUNG customer care center.
Contact SAMSUNG WORLD WIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG
customer care center.
Area
` North America
Canada
Contact Center
Web Site
Area
Switzerland
Contact Center
Web Site
ch_fr/ (French)
0848 - SAMSUNG (7267864,
CHF 0.08/min)
Mexico
Lithuania
Latvia
8-800-77777
8000-7267
800-7267
U.S.A
` Latin America
Estonia
Argentine
0800-333-3733
` CIS
0800-124-421
Brazil
Chile
Russia
8-800-555-55-55
8-800-555-555
4004-0000
Georgia
800-SAMSUNG (726-7864)
00-1800-5077267
800-7919267
Armenia
Azerbaijan
Kazakhstan
Uzbekistan
Kyrgyzstan
Tadjikistan
0-800-05-555
Nicaragua
Honduras
Costa Rica
Ecuador
088-55-55-555
8-10-800-500-55-500
8-10-800-500-55-500
00-800-500-55-500
8-10-800-500-55-500
0-800-507-7267
1-800-10-7267
800-6225
El Salvador
Guatemala
Jamaica
1-800-299-0013
1-800-234-7267
800-7267
ua_ru
Ukraine
0-800-502-000
Panama
Puerto Rico
1-800-682-3180
Belarus
810-800-500-55-500
00-800-500-55-500
Rep. Dominica 1-800-751-2676
Moldova
Trinidad &
` Asia Pacific
Tobago
Australia
1300 362 603
Venezuela
Colombia
` Europe
0-800-100-5303
New Zealand
01-8000112112
400-810-5858
China
010-6475 1880
0810 - SAMSUNG
Austria
Belgium
Czech
(7267864, € 0.07/min)
hk
(852) 3698-4698
Hong Kong
hk_en/
be (Dutch)
02-201-24-18
be_fr (French)
3030 8282
1800 110011
India
1800 3000 8282
800 - SAMSUNG
(800-726786)
1800 266 8282
0800-112-8888
021-5699-7777
Indonesia
Denmark
Finland
France
70 70 19 70
030 - 6227 515
01 48 63 00 00
Japan
0120-327-527
1800-88-9999
Malaysia
01805 - SAMSUNG
1-800-10-SAMSUNG
Germany
(726-7864 € 0,14/Min)
(726-7864)
1-800-3-SAMSUNG
(726-7864)
Hungary
Philippines
Italia
800-SAMSUNG (726-7864)
261 03 710
1-800-8-SAMSUNG
(726-7864)
Luxemburg
02-5805777
0900-SAMSUNG
Singapore
Thailand
Netherlands
Norway
Poland
(0900-7267864) (€ 0,10/Min)
1800-29-3232
02-689-3232
815-56 480
0 801 1SAMSUNG (172678)
Taiwan
0800-329-999
1 800 588 889
022-607-93-33
Vietnam
Portugal
` Middle East & Africa
Slovakia
Turkey
444 77 11
902 - 1 - SAMSUNG
(902 172 678)
Spain
South Africa
U.A.E
800-SAMSUNG (726-7864)
8000-4726
Sweden
Bahrain
Jordan
U.K
0845 SAMSUNG (7267864)
0818 717100
800-22273
Eire
QUESTIONS OR COMMENTS?
COUNTRY
CALL
OR VISIT US ONLINE AT
WRITE
Samsung Electronics America, Inc.
105 Challenger Road Ridgefield Park,
NJ 07660-0511
1-800-SAMSUNG
IN THE US
(7267864)
AK68-01963N
|