43-927.fm Page 1 Thursday, June 24, 1999 9:36 AM
Cat. No. 43-927
OWNER’S MANUAL
CID-927
Please read before using this equipment.
Fashion Caller ID Phone
with 64-Memory Caller ID
43-927.fm Page 3 Thursday, June 24, 1999 9:36 AM
READ THIS BEFORE
INSTALLATION
WARNING: To reduce the risk of fire or shock
hazard, do not expose this product to rain or
moisture.
We have designed your CID-927 to con-
form to federal regulations, and you can
connect it to most telephone lines. How-
ever, each telephone (and each device,
such as an answering machine) that you
connect to the telephone line draws
power from the telephone line. We refer
to this power draw as the device’s ringer
equivalence number, or REN. The REN
is on the bottom of your telephone.
CAUTION
RISK OF ELECTRIC SHOCK.
!
DO NOT OPEN.
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER OR BACK. NO USER-SERVICE-
ABLE PARTS INSIDE. REFER SERVICING
TO QUALIFIED PERSONNEL.
This symbol is intended to alert
you to the presence of uninsu-
lated dangerous voltage within
the product’s enclosure that might
be of sufficient magnitude to con-
stitute a risk of electric shock. Do
not open the product’s case.
If you use more than one telephone or
other device on the line, add up all the
RENs. If the total is more than five, your
telephones might not ring. In rural areas,
a total REN of three might impair ringer
operation. If ringer operation is impaired,
remove one of the devices from the line.
This symbol is intended to inform
you that important operating and
maintenance instructions are
included in the literature accom-
panying this product.
!
FCC STATEMENT
Your CID-927 complies with Part 68 of
FCC Rules. You must, upon request,
provide the FCC registration number
and REN to your telephone company.
Both numbers are on the bottom of the
CID-927.
IMPORTANT CALLER ID
INFORMATION
To use the CID-927’s Caller ID feature,
you must be in an area where Caller ID
service is available and you must sub-
scribe to the service.
Note: You must not connect your CID-
927 to:
Where Caller ID is offered, one or more
of the following options are generally
available:
• coin-operated systems
• party-line systems
• most electronic key phone systems
• caller’s number only
• caller’s name only
• caller’s name and number
3
43-927.fm Page 4 Thursday, June 24, 1999 9:36 AM
The CID-927 also complies with the lim-
its for a Class B device as specified in
Part 15 of FCC Rules. These limits pro-
vide reasonable protection against ra-
dio and TV interference in a residential
area. However, your telephone might
cause TV or radio interference even
when it is operating properly. To elimi-
nate interference, you can try one or
more of the following corrective mea-
sures.
• Reorient or relocate the TV’s receiv-
ing antenna.
• Increase the distance between the
telephone and the radio and TV.
Consult your local RadioShack store if
the problem still exists.
4
43-927.fm Page 5 Thursday, June 24, 1999 9:36 AM
CONTENTS
Preparation .............................................................................................................. 6
Installing Batteries............................................................................................... 6
Connecting the Phone ........................................................................................ 7
Connecting the Handset ..................................................................................... 7
Setting the Dialing Mode .................................................................................... 7
Setting the Ringer’s Volume ............................................................................... 7
Setting the Display Language ............................................................................ 8
Setting the Date and Time .................................................................................. 8
Adjusting the Display Contrast ........................................................................... 8
Phone Operation ..................................................................................................... 9
Using Redial ....................................................................................................... 9
Using Flash ........................................................................................................ 9
Using Tone Services on a Pulse Line ................................................................. 9
Storing and Dialing Priority Numbers ................................................................. 9
Testing Stored Emergency Numbers ......................................................... 10
Chain-Dialing ............................................................................................. 10
Using the Index Card ........................................................................................ 10
Caller ID Operation ............................................................................................... 11
Caller ID Messages .......................................................................................... 11
Reviewing Caller ID Records ............................................................................ 12
Deleting Caller ID Records ............................................................................... 12
Troubleshooting .................................................................................................... 13
Care and Maintenance .......................................................................................... 14
The FCC Wants You to Know ........................................................................... 15
Lightning ........................................................................................................... 15
5
43-927.fm Page 6 Thursday, June 24, 1999 9:36 AM
PREPARATION
2. Press in the tab on the battery com-
partment cover and lift off the cover.
INSTALLING BATTERIES
Your CID-927 requires four AAA batter-
ies (not supplied) to store and display
Caller ID records. For the best perfor-
mance, we recommend alkaline batter-
ies, available at your local RadioShack
store.
3. Put the batteries in the compartment
as indicated by the polarity symbols
(+ and –) marked inside.
Cautions:
• Use only fresh batteries of the
required size and recommended
type.
• Do not mix old and new batteries,
different types of batteries (stan-
dard, alkaline, or rechargeable), or
rechargeable batteries of different
capacities.
4. Replace the cover and secure it with
the screw.
Once you install the batteries,
12:00AM 1/01appears.
Follow these steps to install batteries.
Note: When replacing the batteries, in-
stall the new ones within 2 minutes, or
the CID-927’s date and time will be lost.
(The Caller ID information, however,
stays stored in the CID-927’s memory.)
The telephone company sends the cor-
rect time with each incoming call, so the
correct date and time are automatically
set when the CID-927 receives its first
call.
1. Use a Phillips screwdriver to remove
the screw on the battery compart-
ment cover.
When flashes in the upper right corner
of the display or the display dims, re-
place batteries.
Cautions:
• Always remove old or weak batter-
ies. Batteries can leak chemicals
that can destroy electronic parts.
• Dispose of old batteries promptly
and properly. Do not burn or bury
them.
6
43-927.fm Page 7 Thursday, June 24, 1999 9:36 AM
1. Be sure TONE/PULSE is set to TONE.
CONNECTING THE
PHONE
Plug one end of the supplied modular
cord into the jack on the back of the
CID-927. Then plug the other end of the
cord into the modular phone line jack.
TONE/PULSE
2. Lift the handset and listen for the
dial tone.
3. Press any number except 0.
Note: If your phone system requires that
you enter an access code (9, for exam-
ple) before you dial an outside number,
do not press that number.
CONNECTING THE
HANDSET
If the dial tone stops, you have touch-
tone service. Leave TONE/PULSE set to
TONE.
Plug one end of
the supplied coiled
modular cord into
the jack on the left
side of the phone
and the other end
into the jack on the
If the dial tone continues, you have
pulse service. Set TONE/PULSE to
PULSE.
handset.
place the handset
on the base.
Then
SETTING THE RINGER’S
VOLUME
Set RINGER OFF/LO/HI on the back of
the base to LO for a normal ringer vol-
ume, or HI for a louder ring.
SETTING THE DIALING
MODE
Set TONE/PULSE on the back of the
base for the type of service you have. If
you are not sure which type you have,
do this test.
RINGER OFF/LO/HI
7
43-927.fm Page 8 Thursday, June 24, 1999 9:36 AM
If you do not want the ringer to sound,
set RINGER OFF/LO/HI to OFF. With the
ringer off, you can still make calls (and
answer calls if you hear another phone
on the same line ringing).
SETTING THE DATE AND
TIME
Your phone company sends the date
and time with each incoming call if you
subscribe to Caller ID service. Or, follow
these steps to set the date and time.
SETTING THE DISPLAY
LANGUAGE
Note: If you make a mistake, simply
start again at Step 1.
The CID-927 is preset to show Caller ID
messages in English. Follow these
steps to change the language to French
or Spanish.
1. Press STORE. PROGRAM MODE
appears.
2. Press REVIEW . -:- -/- -with
the date cursor flashing and SET
DATE appear.
Note: If you do not finish a step within
20 seconds and the phone exits setup,
or if you make a mistake, start again at
Step 1.
3. Enter the desired date using number
keys. SET TIMEappears and the
hour cursor flashes.
4. Enter the desired time. =AM
#=PMappears.
5. Press
to select AM or # to select
PM. The phone beeps and the set
time display returns.
STORE
ADJUSTING THE DISPLAY
CONTRAST
1. Press STORE. PROGRAM MODE
appears.
Repeatedly press CONTRAST on the
back of the phone to adjust the display
contrast. The CID-927 beeps once then
the current time display returns.
2. Press REVIEW . SET LANGUAGE
then 1=EN 2=SP 3=FRappears.
3. Press:
• 1 to select English
• 2 to select Spanish
• 3 to select French
The CID-927 beeps once, then the cur-
rent time display returns.
CONTRAST
8
43-927.fm Page 9 Thursday, June 24, 1999 9:36 AM
PHONE OPERATION
Note: If you do not have any special
phone services, pressing FLASH might
disconnect the current call.
USING REDIAL
The redial memory holds up to 32 digits,
so it can store both long-distance and lo-
cal numbers. To redial the last number,
lift the handset then press REDIAL.
USING TONE SERVICES
ON A PULSE LINE
REDIAL
Some special services, such as bank-
by-phone, require tone signals. If you
have pulse service, follow these steps to
use those special services.
1. Be sure TONE/PULSE is set to
PULSE.
Notes:
2. Call the service.
• The redial memory only stores the
last 32 digits of any number dialed.
3. When the service answers, press
. Any additional numbers you dial
are sent as tone signals.
• The redial memory does not store a
flash entry but stores any digits you
press after FLASH (see “Using
Flash”).
STORING AND DIALING
PRIORITY NUMBERS
USING FLASH
You can store emergency phone num-
bers or the phone numbers you call
most frequently in the three priority
memory locations for one-touch dialing.
FLASH performs the electronic equiva-
lent of a switchhook operation for spe-
cial services, such as Call Waiting.
Each memory location can store up to
16 digits.
FLASH
For example, if you have Call Waiting,
press FLASH to answer an incoming call
without disconnecting the current call.
Press FLASH again to return to the first
call.
9
43-927.fm Page 10 Thursday, June 24, 1999 9:36 AM
Notes:
Testing Stored Emergency
Numbers
• You will hear a dial tone during most
steps of this procedure. The phone
does not actually dial the number as
you store it, but you might also hear
a busy tone or recorded operator’s
voice after a few seconds. This is
normal.
If you want to test a stored emergency
number (police department, fire depart-
ment, ambulance), make the test call
during the late evening or early morning
hours to avoid peak demand periods.
Remain on the line to explain the reason
for your call.
• If you do not complete a step within
15 seconds, you must start over
from Step 2.
Chain-Dialing
1. Press STORE. PROGRAM MODE
appears.
For quick recall of numbers for special
services (such as alternate long-dis-
tance or bank-by-phone), you can store
each group of numbers in its own mem-
ory location.
When calling special services, dial the
service’s main number first. At the ap-
propriate place in the call, dial the mem-
ory number for the additional numbers
you want to send.
2. Enter the phone number you want to
store.
Note: If you make a mistake, hold
down the switchhook for a few sec-
onds, then release it and start over
at Step 2.
USING THE INDEX CARD
The index card on the bottom of the
handset provides a convenient place for
you to record names and phone num-
bers for easy reference. Remove the
plastic cover with a small, pointed ob-
ject, such as a straightened paper clip.
Write the names and numbers (in pencil
in case you want to change them later),
then replace the cover.
3. Press M1, M2, or M3 to store the pri-
ority number.
Without hanging up, repeat Steps
2–4 to store other numbers. Hang
up the handset when you are fin-
ished.
To dial a priority memory number, lift the
handset and press M1, M2, or M3.
10
43-927.fm Page 11 Thursday, June 24, 1999 9:36 AM
CALLER ID OPERATION
If you subscribe to Caller ID service from
your phone company, the phone compa-
ny sends information about the call (as
well as the time and date) between the
first and second rings of every call you
receive. The CID-927 displays this call
information and updates the phone’s
built-in clock. The CID-927 can also
show other information about the call.
See “Caller ID Messages.”
CALLER ID MESSAGES
Description (English/
Display
French/Spanish)
Appears when there
are no call records in
NO CALLS
AUCUN
the CID-927’s memory
APPELS
when you press a
NO LLAMADAS
REVIEW key.
Appears when the
caller is not within a
-OUT OF
AREA-
The NEW CALL indicator flashes during
an incoming call, and NEW CALL ap-
pears on the display. The Caller ID
record appears for about 20 seconds,
then the Caller ID and new Caller ID
record totals appear.
Caller ID service area.
-HORS ZONE-
No caller information
-FUERA DE
AREA-
appears.
Appears when you
reach the end of your
call records.
-END OF
LIST-
-FIN DE
LIST-
-FIN DE
LISTA-
Appears when the
Caller ID information
-ERROR-
-ERREUR-
If you subscribe to your phone compa-
ny’s message waiting service, the CID-
was garbled, or when
-ERROR-
there was an error dur-
927 tells you when you have a message
ing the transmission of
Caller ID information. A
-appears where the
data is lost.
MSG
waiting.
appears and remains un-
WAIT
til you retrieve the message.
If your phone company sends informa-
tion indicating that the incoming call is
Appears when the
caller has blocked the
Caller ID information
from being sent.
-PRIVATE
CALL-
APPEL
PERSONNEL
LLAMADA
PRIVADA
long distance,
appears.
11
43-927.fm Page 12 Thursday, June 24, 1999 9:36 AM
Note: You cannot delete Caller ID
records during a call.
REVIEWING CALLER ID
RECORDS
To delete a single Caller ID record, re-
peatedly press REVIEW or to select
a record, then press DELETE twice. If
there are no other records, NO CALLS
appears.
Each time you receive a call, your CID-
927 stores a Caller ID record that you
can review later. A Caller ID record in-
cludes:
• call number (in the order the call is
received)
• time and date of the call
• caller’s telephone number
• caller’s name (if available)
Repeatedly press REVIEW
or
to
see Caller ID records.
REVIEW
DELETE
END OF LISTappears after the first
or last record as you scroll through the
list.
To delete all Caller ID records, wait until
the CID-927 shows the clock display,
then hold down DELETE for about four
seconds. ERASE ALLflashes, then the
phone beeps once to confirm all records
were deleted.
Notes:
• The display shows up to 10 digits of
a phone number. If an incoming
phone number is longer, the display
shows only the last 10 digits.
• The CID-927 returns to the time/
date display after about 20 seconds
if you do not press a key.
DELETING CALLER ID
RECORDS
The CID-927 lets you delete individual
Caller ID records or all reviewed Caller
ID records. It will not delete Caller ID
records that have not been reviewed.
12
43-927.fm Page 13 Thursday, June 24, 1999 9:36 AM
TROUBLESHOOTING
We do not expect you to have any problems with your CID-927, but if you do, the fol-
lowing suggestions might help.
Problem
Possible Cause
No dial tone
The phone line and handset cords might not be
securely connected. Reconnect them.
Display is blank
Batteries are weak (or not installed). Replace
with (or reinstall) new batteries.
Volume drops or you hear unusual
sounds
Someone has picked up another phone on the
same line. Hang up the other phone.
Call is noisy
Interference during the call. Hang up and redial
the number.
Can receive calls, but cannot make
calls
Set T/P correctly for the type of service you have
(see “Setting the Dialing Mode” on Page 7).
If you still have problems, disconnect the phone. If other phones on the same line
work properly, the fault is in this phone or its installation. If you cannot find the prob-
lem, take your CID-927 to your local RadioShack store for assistance.
13
43-927.fm Page 14 Thursday, June 24, 1999 9:36 AM
CARE AND MAINTENANCE
Your RadioShack CID-927 Fashion Caller ID Phone is an example of superior de-
sign and craftsmanship. The following suggestions will help you care for your CID-
927 so you can enjoy it for years.
Keep the CID-927 dry. If it gets wet, wipe it dry immediately. Liquids
might contain minerals that can corrode the electronic circuits.
Use and store the CID-927 only in normal temperature environments.
Temperature extremes can shorten the life of electronic devices, dam-
age batteries, and distort or melt plastic parts.
Keep the CID-927 away from dust and dirt, which can cause premature
wear of parts.
Handle the CID-927 gently and carefully. Dropping it can damage cir-
cuit boards and cases and can cause the CID-927 to work improperly.
Use only fresh batteries of the required size and recommended type.
Batteries can leak chemicals that damage your CID-927’s electronic
parts.
Wipe the CID-927 with a damp cloth occasionally to keep it looking
new. Do not use harsh chemicals, cleaning solvents, or strong deter-
gents to clean the CID-927.
Modifying or tampering with the CID-927’s internal components can cause a mal-
function and might invalidate its warranty and void your FCC authorization to oper-
ate it. If your CID-927 is not performing as it should, take it to your local
RadioShack store for assistance. If the trouble is affecting the telephone lines, the
phone company can ask you to disconnect your CID-927 until you have resolved
the problem.
14
43-927.fm Page 15 Thursday, June 24, 1999 9:36 AM
THE FCC WANTS YOU TO
KNOW
In the unlikely event that your CID-927
causes problems on the phone line, the
phone company can temporarily discon-
tinue your service. If this happens, the
phone company attempts to notify you in
advance. If advance notice is not practi-
cal, the phone company notifies you as
soon as possible and advises you of
your right to file a complaint with the
FCC.
Also, the phone company can make
changes to its lines, equipment, opera-
tions, or procedures that could affect the
operation of this telephone. The tele-
phone company notifies you of these
changes in advance so you can take the
necessary steps to prevent interruption
of your telephone service.
LIGHTNING
Your CID-927 has built-in protection cir-
cuits to reduce the risk of damage from
surges in telephone line and power line
current. These protection circuits meet
or exceed the FCC requirements. How-
ever, lightning striking the telephone or
power lines can damage your phone.
Lightning damage is not common. Nev-
ertheless, if you live in an area that has
severe electrical storms, we suggest
that you unplug your phone during
storms to reduce the possibility of dam-
age.
15
43-927.fm Page 16 Thursday, June 24, 1999 9:36 AM
Limited One-Year Warranty
This product is warranted by RadioShack against manufacturing defects in material and workman-
ship under normal use for one (1) year from the date of purchase from RadioShack company-owned
stores and authorized RadioShack franchisees and dealers. EXCEPT AS PROVIDED HEREIN,
RadioShack MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIES, INCLUD-
ING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIM-
ITED IN DURATION TO THE DURATION OF THE WRITTEN LIMITED WARRANTIES CONTAINED
HEREIN. EXCEPT AS PROVIDED HEREIN, RadioShack SHALL HAVE NO LIABILITY OR RE-
SPONSIBILITY TO CUSTOMER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY
LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE OR PERFOR-
MANCE OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY, INCLUD-
ING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM INCONVENIENCE, LOSS OF
TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT, SPECIAL, INCIDENTAL,
OR CONSEQUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN ADVISED OF THE POSSI-
BILITY OF SUCH DAMAGES.
Some states do not allow the limitations on how long an implied warranty lasts or the exclusion of in-
cidental or consequential damages, so the above limitations or exclusions may not apply to you.
In the event of a product defect during the warranty period, take the product and the RadioShack
sales receipt as proof of purchase date to any RadioShack store. RadioShack will, at its option, un-
less otherwise provided by law: (a) correct the defect by product repair without charge for parts and
labor; (b) replace the product with one of the same or similar design; or (c) refund the purchase
price. All replaced parts and products, and products on which a refund is made, become the prop-
erty of RadioShack. New or reconditioned parts and products may be used in the performance of
warranty service. Repaired or replaced parts and products are warranted for the remainder of the
original warranty period. You will be charged for repair or replacement of the product made after the
expiration of the warranty period.
This warranty does not cover: (a) damage or failure caused by or attributable to acts of God, abuse,
accident, misuse, improper or abnormal usage, failure to follow instructions, improper installation or
maintenance, alteration, lightning or other incidence of excess voltage or current; (b) any repairs
other than those provided by a RadioShack Authorized Service Facility; (c) consumables such as
fuses or batteries; (d) cosmetic damage; (e) transportation, shipping or insurance costs; or (f) costs
of product removal, installation, set-up service adjustment or reinstallation.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.
RadioShack Customer Relations, Dept. W, 100 Throckmorton St., Suite 600, Fort Worth, TX 76102
We Service What We Sell
3/97
RadioShack
A Division of Tandy Corporation
Fort Worth, Texas 76102
05A99
Printed in Malaysia
|