Power Acoustik PADVD 220T User Manual

PADVD-220/ PADVD-220T  
Single-DIN A/V Multimedia Source  
Touch Sensor  
DVD/CD/MP3/MP4  
AM/FM Radio  
Built-in TV tuner  
Owner’s Manual  
Take the time to read through this owner’s manual.  
Familiarity with installation and operation procedures will help you obtain the best  
Performance from your new DVD-receiver.  
Important Safeguards  
z Using the device at temperature below -10may cause the breakage of the device. BEFORE  
USING PLEASE HEAT UP THE PASSENGER COMPARTMENT TO THE RECOMMENDED  
TEMPERATURE!  
z Read carefully through this manual to familiarize yourself with this high-quality sound system.  
z Disconnect the vehicle's negative battery terminal while mounting and connecting the unit.  
z When replacing the fuse, be sure to use one with an identical amperage rating. Using a fuse with  
a higher amperage rating may cause serious damage to the unit.  
z DO NOT attempt to disassemble the unit. Laser beams from the optical pickup are dangerous to  
the eyes.  
z Make sure that pins or other foreign objects do not get inside the unit; they may cause  
malfunctions, or create safety hazards such as electrical shock or laser beam exposure.  
z If you have parked the car for a long time in hot or cold weather, wait until the temperature in the  
car becomes normal before operating the unit.  
z DO NOT open covers and do not repair yourself. Consult the dealer or an experienced  
technician for help.  
z Make sure you disconnect the power supply and aerial if you will not use the system for a long  
period or during a thunderstorm.  
z Make sure you disconnect the power supply if the system appears to be working incorrectly, e. g,  
making unusual sounds, smelling strange, emitting smokes from inside or liquid having gotten  
inside itHave a qualified technician check the system.  
z The unit is designed for negative terminal of the battery, which is connected to the vehicle metal.  
Please confirm it before installation.  
z Do not allow the speaker wires to be shorted together when the unit is switched on. Otherwise it  
may overload or burn out the power amplifier.  
z Do not install the detachable panel before connecting the wire.  
z Don't remove the detachable panel when encoding.  
Page -2  
Accessories  
Package contains the following accessories for installation and operation of the unit.  
(1) Washer, Spring  
1 each  
Washer, M5 Nut  
(2) Mounting Strap  
1
(3) Screw  
(4) Bolt  
1
4
(5) Mounting Collar  
1
(6) Release Key  
2
1
(7) Rubber Cushion  
Owner’s Manual  
Remote Controller  
Panel Carrying Case  
AUX IN Cable  
Page- 3  
Installation/Un-Installation  
First complete the electrical connections, and then check them for correctness.  
Installation  
This unit can be installed in any dashboard having an opening as shown on the picture. The  
dashboard should be 4.75 – 5.56 mm thick in order to be able to support the unit.  
1. Insert mounting collar into the dashboard, and bend the mounting tabs out with a screwdriver.  
Make sure that lock leveris flush with the mounting collar (not projecting outward).  
2. Secure the rear of the unit.  
After fixing mounting bolt and power connector, fix the rear of the unit to the car body by rubber  
cushion.  
3. Insert trim plate.  
When you prepare to insert trim plate, please check its direction. Once it was up side down, it  
cannot be fixed.  
Lock lever(※)  
Un-installation  
Remove Trim Ring and insert Release Keys into left and right side-end holes as shown in below  
picture and pull the unit out of the dashboard.  
Page -4  
Wiring Connections  
Make sure you have good chassis ground. A good ground connection will eliminate most electrical  
noise problems. A good chassis ground requires a tight connection to the vehicle’s metal chassis.  
The area around the ground connection should be clean, bare metal without rust, paint, plastic, dust,  
or dirt for a good electrical connection.  
Using the ISO Connector  
1. If your car is equipped with the ISO connector, then connect the ISO connectors as illustrated.  
2. For connections without the ISO connectors, check the wiring in the vehicle carefully before  
connecting, incorrect connection may cause serious damage to this unit.  
3. Cut the connector, connect the colored leads of the power cord to the car battery as shown in the  
color code table below for speaker and power cable connections.  
Location Function  
Connector A  
Connector B  
1
2
3
4
5
6
7
8
Rear Right(+)---Purple  
Rear Right(-)---Purple/Black Stripe  
Front Right(+)---Grey  
Battery 12V (+)/yellow  
Auto Antenna/blue  
Front Right(-)---Grey/Black Stripe  
Front Left(+)---White  
Front Left((-)---White/Black Stripe  
Rear Left(+)---Green  
ACC+/red  
Ground/black  
Rear Left(-)---Green/Black Stripe  
**TV antenna is for  
PADVD-220T only.  
Page- 5  
Caution: Do not interchange the connection of the wiring!!!  
For some car models you may need to modify wiring of the supplied power cord. Contact your  
authorized car dealer before installing this unit.  
Remark: When you back a car, screen display switch to Rear Camera automatically  
Detachable Control Panel  
Detaching the control panel  
z Turn the Power off.  
z Press OPEN button release the panel.  
z Pull the panel out.  
Attaching the control panel  
z Insert the left side of the control panel into the main unit.  
z Press the control panel right side until the “click” sound is heard.  
Caution:  
DO NOT insert the control panel from the right side. It can damage the control panel.  
The control panel can easily be damaged by shocks. After removing it, place it in a protective case  
and be careful not to drop it or subject it to strong shocks.  
The rear connector that connects the main unit and the control panel is an extremely important part.  
Be careful not to damage it by pressing on it with fingernails, pens, screwdrivers, etc.  
Note:  
If the control panel is dirty, wipe off the dirt with soft, dry cloth only. And use a cotton swab soaked in  
isopropyl alcohol to clean the socket on the back of the control panel.  
Page -6  
Panel Controls  
1. Power/Mute  
2. BAND  
3. PREVIOUS  
4. VOL +  
5. NEXT  
6. DISP  
7. AS/PS  
8. LCD  
14. PRESET 1/play pause  
15. PRESET 2./RPT  
16. PRESET 3./INT  
17. PRESET 4/RDM  
18. PRESET 5/STOP  
19. PRESET 6/MENU  
20.AUX IN JACK  
21.USB SLOT  
9. IR sensor  
10. OPEN  
11.MODE.  
12.OK  
22.SD SLOT  
23.EJECT  
24.DISC SLOT  
25.RESET  
13.VOL-  
Page- 7  
IR Remote Control  
1. MODE  
2. POWER  
3. BND/RDM  
4. ENTER  
5. Cursor / / /  
6. STEREO/MONO  
7. LOC/ PROG  
8. P.SCN/RPT  
9. SEEK-/  
10. LOUD  
11. OSD  
12. STOP/ PBC  
13. Digit 0-9  
14.  
15. MUTE  
16. MENU  
17. SUB-T  
18. SETUP  
19. ANGLE  
20. INT  
21. VOL+  
22. A-B/ZOOM  
23. SEL  
24. SEEK+/  
25. VOL-  
REPLACING THE BATTERY  
26. AUDIO/ GOTO  
Remote Control comes with a CR-2025 Lithium Battery included.  
1. Remove the Battery Holder from the back of the Remote Control.  
2. Insert a CR-2025 Lithium battery with the positive (+) mark upward. Insert the Battery Holder into  
the back of the Remote Control.  
+3V  
(CR 2025)  
Warning: Store the battery where children cannot reach. If a child accidentally swallows the battery,  
consult a doctor immediately.  
Do not re-charge, short, disassemble or heat the battery or dispose it in fire.  
Do not expose or bring into contact the battery with other metallic materials. Doing this may cause  
the battery to give off heat, crack or start a fire.  
When throwing away or saving the battery, wrap it in tape and insulate; otherwise, the battery may  
give off heat, crack or start a fire.  
Page -8  
General Operations  
Reset the Unit  
In case the unit is malfunctioned or need to reset to factory default setting, press RESET button in  
inner panel then the unit will be reset.  
Power on/off  
Press POWER key button to turn on the unit.  
Long press POWER key on front panel or press POWER button on RC to power off the unit.  
Under Power on mode, short press comes in mute.  
Mode Setting  
Press MODE button on front panel or remote control to change mode in a sequence of: Tuner  
=>DVD => USB =>Card=>TV => AV IN=> Tuner  
(When USB/ Card/ DVD available.)  
Loudness  
Press button on remote control to set LOUD ON/OFF.  
DISP button  
Short press shows time, Long press adjust clock. Press VOL+/- adjust hours then press SEL can  
adjust minutes. Press DIS quit clock adjust.  
Band button  
In radio mode, press to select FM1-FM2-FM3-AM1-AM2; In TV mode, press to select TV system  
Volume Control  
Press VOL +/- button increase/ decrease the volume level.  
Audio Setting  
Press SEL button on the Remote Control or press OK key on the front panel to select the audio  
setting:  
VOL=>BASS =>TREBLE => BALANCE => FADER =>LOUD=> EQ=>SUB-W.  
=>STEREO=>DX=>BEEP=>12H/24H=>EXIT  
Press VOL +/- buttons on remote to select the audio setting item (or press the VOL +/- on front  
panel to select the setting item).  
.
Notes: If turn off the power, all the settings of each mode will be saved.  
- If you don’t adjust setting within 5 seconds after selecting the desired setting item, the unit will  
automatically return to the current mode.  
On-Screen Display (OSD).  
Press one time to show the current playing track/ played time information, long press twice to show  
the current playing track/ remainder time for play, long press again to clear the information.  
Page- 9  
Digital Tuner  
Band selection  
Press MODE button to select the RADIO mode.  
Press the BAND button to select the desired band: FM1=> FM2 => FM3 => AM1=>AM2  
STEREO/MONO  
In FM mode, press SETREO/MONO button on remote control to select stereo or mono sound  
reception.  
Manual/ automatic tuning  
z Manual tuning: press the  
for 2 seconds to enter the manual tuning mode. Press the  
the Remote repeatedly to select a station downward or upward step by step.  
/
buttons on remote control(or on the front panel ) and hold  
/
buttons on the panel or on  
z Automatic tuning: press the  
/
buttons on remote control(or on the front panel ), the  
automatic search will start. It will play when finds the station.  
Preset station 1-6 play and setting  
z Play preset station: Short press number key 1-6 on remote control or panel to play the preset  
station 1-6.  
z Preset station setting: during manual turning or automatic tuning, press and hold the number  
1-6 buttons on remote or panel to store the preset station 1-6  
Remark: You can store up to a total of 30 radio stations in the memory (18FM, 12AM).  
AS (Auto Store) / PS (Preset Scan)  
AS (Auto Store): In tuner mode, Press the RPT/P.SCN button on the remote or panel press the  
AS/PS button and hold for 2 seconds to store radio station’s with the best reception to the preset  
buttons automatically.  
PS (Preset Scan): In tuner mode, short press this button to scan the preset memorized station,  
each preset scan for 5 seconds. Press again to stop operation.  
Page -10  
SD/MMC Cards & USB Operations  
USB Flash Memory  
To play MP3/ MP4/ WMA files from a USB flash memory, insert a USB flash memory into the USB  
port on the right side of the unit. The unit will start playing MP3/MP4/ WMA files on the USB flash  
memory automatically. Or press the MODE button to select USB after pressing POWER button to  
turn on the unit.  
SD/MMC Card  
To play MP3/ MP4/ WMA files on a SD/MMC card, insert the card into the card slot (you should  
press the OPEN button on the panel to flip down front panel and insert the card into card slot.) The  
unit will start playing MP3/ MP4/ WMA files on the card memory automatically. Or press the MODE  
button to select Card after pressing POWER Button to turn on the unit.  
PAUSE/ PLAY  
Press the PLAY/ PAUSE button to pause the playback. Press the button again to resume.  
STOP  
Press the STOP button on remote or on the panel to stop playback. Press the PLAY/ PAUSE button  
to resume. If the card or USB is removed, the resume function will be cancelled.  
Press the STOP button twice to stop the playback totally. Press the PLAY/ PAUSE button to start  
playback from the beginning  
Selecting Tracks  
If the MP3/ MP4/ WMA files are stored in the folders on the USB drive or Card, the unit will start by  
playing the first song in the first folder. After playing all the files sequentially in the first folder, the  
unit will play all the files sequentially in the next folder. The unit will continue playing through all of  
the folders on the USB drive or card in this manner. Press the  
button to play the previous  
track/chapter. Press the  
the desired track/chapter.  
to play the next track/chapter. Press the digital buttons (0-9) to select  
Select File From Folder  
When playing MP3/MP4/WMA file, press “ ” on remote control, cursor move to  
folder “..”, then press “Enter” to confirm selection.  
Or, press “5/” on front panel, then press “ ” to select folder “..”, then press “  
to confirm selected folder.  
GOTO Function  
Long press AUDIO/GOTO button on remote control to show GOTO menu, use 0-9 to input track/  
time to go to directly.  
Fast Forward and Backward  
Press the  
/
buttons and hold for two seconds to select the fast playing in backward or  
forward in 2 times, press and hold for two seconds again for 4times, repeat this operation for 8 times  
=> 16 times =>32 times => play. Press the PLAY/PAUSE button to return to normal playback.  
Note: During the card or USB playback when Fast backward or forward gets to the beginning of the  
playing another track, it resumes normal playback.  
Page- 11  
Repeat  
Press the RPT button on remote control or the panel for RPT1 (repeat the current playing file) =>  
RPT ALL (repeat all folders) => RPT folder (repeat current folder) => RPT OFF.  
Repeat A-B Function  
1. Press A-B button on the remote at the starting point of the section you want to repeat (point A).  
2. Press A-B button again at the ending point of the section you want to repeat (point B). Section  
A-B repeating starts.  
3. Press A-B button again to cancel the A-B repeat function.  
Random  
Press the RDM button on remote or on the panel to play all song tracks in random order.  
Note: This function is only for audio files.  
Intro Playback  
Press the INT button on remote or on the panel to play the beginning of every track for 10 seconds  
in sequence. Press again to cancel INT play.  
Note: This function is only for audio files.  
Programming the Playback  
1. Press PROG button on the remote open program menu.  
2. Use / / / buttons to select the program position and use digit 0-9 buttons to select the  
desired track.  
3. Move the cursor to select START and press ENTER button on remote to play.  
5. Press PROG again or move the cursor to select EXIT to cancel program play.  
ZOOM  
Press ZOOM button and hold for 2 seconds on remote to activate zoom function in the following  
sequences: ZOOM 2 => ZOOM 3 =>ZOOM 4 => ZOOM 1/2=>ZOOM 1/3=>ZOOM 1/4=>ZOOM  
OFF.  
Rotate Picture (only for picture files)  
In picture mode, press  
/
buttons to rotate picture 90 degrees.  
System Menu  
In USB/ Card mode, press SETUP button on remote to show system menu. Press / / / buttons  
to set system data, press this button again to save input data and exit system menu.  
Page -12  
Discs operations  
Glossary  
PBC (Play Back Control)  
Play Back Control is a menu recorded on the disc with SVCD or VCD2.0 format. For the discs  
contained PBC, it can playback interactive software with the menu displayed on TV. And if the disc  
contains still images, it can playback high definition of still image.  
Title  
The title is the important part of DVD disc. The memory volume of the disc is rather big, that makes  
possible to record several films on one disc. For example, if a disc contains three films, they may be  
divided into Title 1, Title 2 and Title 3. You can easily use the functions to search.  
Chapter  
A title can be divided into several blocks, so that every block can be operated as a unit, the unit is  
called chapter.  
The chapter contains a unit at least.  
Discs for playback  
z This unit can play:  
DVD/SVCD/VCD/HDCD/MP3/MP4/WMA/CDDA/Picture-CD/JPEG/CD-R/-RW/DVD±R/±RW.  
z The following file types are supported:  
Audio files: MP3 (*.mp3)  
WMA (*.wma)  
Video files: MP4 (*.avi, Divx3.11/ 4.0/5.0 and XVID)  
MPEG 2(*.vob)  
MPEG 1(*.dat)  
Picture file: JPEG (*.jpg)  
z ISO 9660 or ISO 9660 +Joliet format - Max. 30 characters  
z Max. Track number is 448  
z Max. nested directory is 8 levels  
z The max. album number is 99  
z The max. length of each track is 99 minutes 59 seconds  
z Supported sampling frequency for MP3 disc: 8 KHz to 48 (44.1 KHz preferably) KHz  
z Supported bit-rates of MP3 disc are: 32 - 320 kbps (128 kbps preferably).  
z Following formats are NOT supported *.ACC, *.DLF, *.M3U, *.PLS, MP3 PRO, files with DRM.  
z Open session discs are NOT supported.  
Loading a disc  
1. Turn the power on.  
2. Press the Open button on the front panel to flip it down.  
3. Insert the disc with the printed side facing upward into the slot. The panel will be closed  
automatically. The DVD mode will be turned on automatically. The monitor will show the disc  
content.  
4. Press Open button on the panel and Eject button inner the panel to eject the disc.  
If the disc is not removed for about 10 seconds after reject, the disc will reinserted automatically.  
When disc in/out, put front panel at 0 degree to avoid distort the disc.  
5 You may also choose the playing mode using the MODE button.  
Page- 13  
Playing/pausing  
To ensure good system performance, wait until the unit finishes reading the disc information before  
proceeding.  
Press the PLAY/ PAUSE button to start/ pause the playback. In pause mode press it again to  
resume the playback.  
Stop  
During playback press the STOP button on the RC or on the panel. Playback will be stopped. Press  
the PLAY/ PAUSE button again to start playback from the position at which it was stopped. If the  
disc is removed, the resume function is cancelled.  
Press the STOP button twice to finally stop the playback. Press the PLAY/ PAUSE button to start  
playback from the very beginning  
Playing the previous/ next track/ chapter  
1. During playback press the  
2. Press the  
3. Press the digital buttons (1-9, 0) buttons to enter the desired track/chapter number.  
button to start playing the previous track/chapter.  
to start playing the next track/chapter.  
Speed forward and backward  
Long press the  
/
buttons on the panel or press and hold for 2 seconds the  
or  
on the RC to select the speed of fast playing in backward or forward direction: X2, X4, X8, X16, X32.  
Press the PLAY/PAUSE button to return to normal playback.  
Note: During the disc playback when Fast/ Reverse Playback gets to the beginning of the playing  
another track, it resumes normal playback.  
Repeat playback  
Press the RPT/P.SCN button on the RC or on the panel once or more times to repeat the playback:  
- For VCD/CD: display appears Repeat Track => Repeat ALL => Off (Some discs do not support  
this functions).  
- For DVD: display appears Repeat Chapter => Repeat Title =>ALL =>Off  
- For File disc: display appears RPT ONE => RPT ALL=> RPT FOLDER => Off  
Repeat A-B function  
1. During playback, press A-B button on the remote control at the starting point of the section you  
want to repeat (point A).  
2. Press A-B button again at the ending point of the section you want to repeat (point B). Section  
A-B repeating starts.  
3. Press A-B button again to cancel the A-B repeat function.  
Random playback (for CD/VCD/MP3 discs)  
During disc playback, press the RDM button on the RC or on the panel to start random playback of  
the disc. Press again to cancel.  
Intro playback (for CD/VCD discs)  
You can play the beginning of every track for 10 seconds in sequence. Press the INT button on  
remote control or on the panel to start intro play of whole disc. Press again to cancel.  
Page -14  
PBC (Playback Control) function (for VCD only)  
If you insert a VCD with PBC, playback starts from the beginning of the 1st track automatically.  
1. Long press PBC/STOP button to activate interactive menu on screen during playback.  
2. If the menu consists of titles, you can select a desired one using the digit 0-9 buttons.  
3. The VCD starts playing the selected title automatically or press ENTER button to confirm the  
selected track for playback.  
MENU function (for DVD only)  
1. Press MENU button on the RC or on the panel to s activate interactive DVD menu on screen  
during playback  
2. Long press MENU button on the RC to s activate interactive DVD title menu on screen during  
playback  
3. If the menu consists of titles, you can select a desired one cursor the  
4. press ENTER button to confirm the selected track for playback.  
/
or / buttons.  
Programming the playback  
1. Press PROG button on the RC to enter program list.  
2. Use , , ,  
buttons and digit buttons to enter the number of the desired track to be on  
selected position.  
For DVD and File disc, select title and chapter number.  
For VCD and CD, select track number.  
3. Move the cursor to select START and press ENTER to play.  
4. If you want to change page, move the cursor to NEXT  
previous page  
or prev  
to change next or  
5. Press PROG again or move the cursor to select EXIT to cancel program play.  
Selecting different audio modes  
z For DVD disc: press AUDIO on the RC repeatedly to select the audio language to listen (if the  
disc supports multi-language mode).  
z For VCD disc: press AUDIO on the RC repeatedly to select the following modes:  
MONO LEFT MONO RIGHTMIX MONOSTEREOEXIT  
Changing the subtitle language (for DVD only)  
Press SUBTITLE button on the RC to select the preferred language for the disc menu. When the  
selected language is recorded on the disc then this language will automatically be selected. If not,  
the first language recorded on the disc is displayed.  
Changing size  
Press and hold for 2 seconds the A-B/ZOOM on the RC. The picture will be enlarged accordingly:  
X2 => X3 =>X4 => X1/2=>X1/3=>X1/4X=>Normal.  
Changing angle (for DVD only)  
If DVD discs support multi-angle playback, press ANGLE on the RC button to playback images in  
different camera angles. If discs doesn't support multi-angle playback, this function will not work. If  
no operation within 1 second, angle description will disappear.  
Page- 15  
MP3 overview  
Notes on MP3:  
z MP3 is short for MPEG Audio Layer 3 and refers to an audio compression technology standard.  
z This product allows playback of MP3 files on CD-ROM, CD-R or CD-RW discs.  
z The unit can read MP3 files written in the format compliant with ISO 9660. However it does not  
support the MP3 data written by the method of packet write.  
z The unit can not read an MP3 file that has a file extension other than “.mp3”.  
z If you play a non- MP3 file that has the “.mp3” extension, you may hear some noise.  
z In this manual, we refer to what are called “MP3 file” and “folder” in PC terminology as “track” and  
“album”, respectively.  
z Maximum number of directory level is 8, including the root directory. Maximum number of files  
and folders per disc is 448.  
z The unit may not play tracks in the order of Track numbers.  
z The unit plays only the audio tracks if a disc contains both audio tracks and MP3 files.  
z When playing a disc of 8 kbps or “VBR”, the elapsed playing time in the display window will not  
be correct and also the intro play may not function properly. “VBR”: Variable Bit Rate.  
Notes on creating your own CD-R or CD-RW containing MP3 files:  
z To enjoy high quality sound, we recommend converting to MP3 files with a sampling frequency of  
44.1 kHz and a fixed bit rate o f 128 kbps.  
z DO NOT store more than 448 MP3 files per disc.  
z For ISO 9660 - compliant format, the maximum allowable depth of nested folders is 8, including  
the root directory (folder).  
z When CD-R disc is used, playback is possible only for discs, which have been finalized.  
z Make sure that when MP3 CD-R or CD-RW is burned that it is formatted as a data disc and NOT  
as an audio disc.  
z You should not write non-MP3 files or unneeded folders along with MP3 files on the disc  
otherwise it takes a long time until the unit starts to play MP3 files.  
z With some CD-R or CD-RW media, data may not be properly written depending on its  
manufacturing quality. In this case, data may not be reproduced correctly. High quality CD-R or  
CD-RW disc is recommended.  
z Up to 16 characters are displayed for the name of an Album or a Track. ID3TAG version 1.x is  
required.  
z Note that the unit may not play Tracks in the order that you wrote them to the disc.  
1. Audio files:  
MP3, WMA  
2. Video files:  
MPEG4 TM1 3.11, 4X, 5X and 6X versions  
Nero Digital TM2  
Real time MPEG2 MP@ML display  
Real time MPEG1 D1 (720X480X30/ 720X576X25) decoding  
Page -16  
Setup Menu  
Press SETUP button to enter the system settings main menu;  
Press cursor  
/
buttons to move along icons on the top navigation bar on settings main menu.  
Select one of the setup pages: General, Speaker, Downmix, Audio;  
Press cursor  
Press cursor  
/
buttons to choose a setting or return to the Setup Page;  
button to enter the highlighted setting;  
Press ENTER button on remote contro confirm your setting.  
General settings  
Menu  
entry  
Function  
Here you can adjust the output  
format for the DVD playback  
according to your preferences.  
TV  
Display  
This function is indicated in  
the device menu but not  
supported by the device.  
Angle  
Mark  
This menu item allows you to  
set the language of this menu.  
OSD  
language  
This function displays  
subtitles as long as those are  
available on the data carrier  
and the function is activated.  
Chose ON or OFF about last  
memory ,chose ON ,turn off the  
sreen the memory will be  
save,chose OFF turn on the  
unit will be back to the default  
setting .  
Captions  
Screen  
Saver  
Speaker settings  
Menu  
entry  
Function  
Here you can set the format in  
which the DVD sound should  
be played back. STEREO =  
analog stereo signal RIGHT /  
LEFT = Dolby Pro Logic stereo  
signal (2 channel sound)  
SURROUND = Virtual  
Downmix  
surround sound If STEREO  
has been switched on,  
“STR“ will appear, for RIGHT /  
LEFT, LTRT“ will appear, and  
for SURROUND, “VSR“.  
Page- 17  
Dolby settings  
Menu  
entry  
With this menu item you can  
select the type of Left and Right  
channel audio output. Stereo is  
normal Stereo, Mono L is all  
sound on the Left Audio output,  
Mono R is all sound on the  
Right channel. The “Mix Mono”  
function only works when a  
DVD is being played in DTS 5.1  
mode.  
Dual  
mono  
Video settings  
Menu  
entry  
This serves to set the  
Sharpness sharpness of the image (high  
/ medium / low).  
This serves to set the  
Brightness brightness of the image (- 20  
to + 20).  
This serves to set the  
Contrast  
contrast of the image (- 10 to  
+20)  
Preference settings  
Page -18  
Menu  
entry  
Function  
This setting enables the selection of the appropriate TV standard. PAL is the  
customary standard in Europe. NTSC is the customary standard in the US and  
Japan. Only select the MULTI option if your TV can play back both formats. Here the  
output signal is automatically adjusted to the standard of the inserted DVD. If the  
“MULTI” setting is selected, “AUTO” will be displayed to the left of the selection  
menu.  
TV Type  
This enables the selection of the desired dubbed language. If the language selected  
here is not available on the inserted data carrier, the first language that is found will  
be played back.  
Audio  
This enables the selection of the desired subtitles. If the subtitles selected here are  
not available on the inserted data carrier, the first subtitles that are found will be  
played back.  
Subtitle  
This enables the selection of the desired menu language. If the language selected  
here is not available on the inserted data carrier, the first language that is found will  
be played back  
Disc  
Menu  
This serves to set the desired age rating.  
1) Child = Kid safe  
2) G = some guidance advisable  
After setting the age rating, you  
3) PG = Parental guidance suggested, some  
will be prompted to enter a  
material may not be suitable for children  
password. The factory default  
4) PG 13 = Parents strongly cautioned, some  
password is set to 1369. Enter  
material may be inappropriate for children under  
this through the number buttons  
13  
Parental  
on the remote control. Now  
5) PGR = Restricted, under 17 requires  
accompanying parent or adult guardian  
arrow buttons. Then confirm your  
6) R = Restricted viewing  
select “YES” or “NO” with the  
selection with the "ENTER"  
button.  
7 ) NC17 = No one 17 and under admitted  
8) 18 or older = for Adult Entertainment or X  
rated movies and NO PARRENTAL is for  
General Audiences (All Ages).  
This function serves to protect the selected settings. The factory default password is  
1369.  
Password  
Default  
This function resets the DVD device settings to the factory default settings.  
Note: If you have forgotten your changed password, you can set a new one at any time by entering  
the factory default password 1369..  
Factory default settings (“RESET“)  
By using the reset function, the device can be changed back to the factory default settings. To use  
the reset function, please press the button REL on the device. Now the operating unit can be  
carefully detached towards the front and left. Now press the RESET button on the device with a thin,  
sharp object. The device will then be reset and turned off if required.  
Note:  
When the factory settings are restored, the clock and the stored radio stations will also be reset  
Page- 19  
TV OPERATIONS (TV function is for PADVD-220T only)  
Connect TV antenna as it is shown on electrical connection diagram.  
Switch to TV mode  
Press MODE button repeatedly to select the TV mode, and press BAND select TV system: PAL DK  
PAL IPAL BGPAL MPAL NSCEAM DKSCEAM BGNTSC M  
Auto tuning  
1. Press  
/  
cursor buttons on RC or ︱  
/  
buttons on panel or touchable  
screen to start auto search of available TV station in backward/forward direction. When the first  
available station is found searching will be stopped and the station found will be played. Press  
these buttons again to continue searching.  
Manual tuning  
Press and hold for 2 seconds  
on panel or touchable screen repeatedly to search the TV stations step by step.  
/  
cursor buttons on RC or ︱  
/  
buttons  
Auto preset memory  
1. Press RPT/P.SCAN button on the RC or Press AS/PS button on panel to start auto tuning; the  
search range is the current TV frequency range. The stations found will be stored into the memory  
automatically.  
2. Press this button again to stop auto searching.  
Select the TV station  
1. Press number buttons on the RC 0-9 to recall the desired TV station.  
2.Press number button on front panel 1-6 to recall the desired TV station.  
Other functions  
Subwoofer  
Connect the subwoofer to the unit using sub output (see electrical diagram). Press SEL button,  
choose expert and set subwoofer ON to enable subwoofer.  
Anti-theft system  
Remove the panel  
1. Press the PWR button to turn the power off.  
2. Press OPEN button to detach the panel.  
3. Pull the panel out.  
4. Place the panel into the case and take it with you when you leave the car.  
Remove the unit  
1. Remove the panel and the trim plate.  
2. Insert both T-Keys into hole on the front of the set until they lock.  
3. Pull out the unit.  
Page -20  
Note on Discs  
Only use groundless loudspeakers.  
Use only loudspeakers of minimal 40 Watt, using fewer watts may result in damaging your loud  
speakers at higher volumes.  
Use 4~8 (Ohm impedance) loudspeakers only; using higher or lesser impedance may  
damage the unit.  
Do not use 3-cable loudspeakers and do not connect the loudspeakers minus to the car body.  
(GND). using a BTL circuit and each loudspeaker must be connected with insulated cables  
according the diagram.  
Loudspeaker cables and/or optional external power amplifiers must always be about 30cm.  
away from the antenna and/or antenna extension parts.  
Page- 21  
Troubleshooting guide  
Symptom  
Cause  
Solution  
If the power supply is properly connected to the  
General  
The car ignition is not on. car  
No power  
The fuse is blown.  
accessory switch the ignition key to “ACC”.  
Replace the fuse.  
Disc  
Disc cannot be  
loaded.  
Presence of disc inside  
the player  
Remove the disc in the player then put a new  
upward.  
Inserting the disc in  
upside down.  
Compact disc is  
Insert the compact disc with the label facing  
upward.  
Disc cannot be  
read.  
extremely dirty or  
defective.  
Temperature inside the  
car is too high.  
Clean the disc or try to play a new one.  
Cool off until the ambient temperature returns to  
normal.  
Volume is in minimum.  
Wiring is not properly  
connected.  
Adjust volume to a desired level.  
Check wiring connection.  
No sound  
The built-in  
The operation  
keys do not  
work.  
microcomputer is not  
operating properly due to  
noise.  
Press the RESET button.  
Reinstall the front panel.  
Front panel is not properly  
fix into its place.  
The installation angle is  
more than 30 degrees.  
Adjust the installation angle to less than 30  
degrees.  
Sound skips.  
The disc is extremely dirty Clean the compact disc/try to play a new one.  
or defective.  
The radio does  
not work, the  
radio station  
automatic  
selection does  
not work.  
The antenna cable is not  
connected the signals are manually.  
too weak.  
Insert the antenna cable firmly select a station  
Page -22  
Specification  
General  
Power supply:  
12 V DC  
Current consumption: max. 10 A  
Maximum power  
output:  
40W x 4 channels  
Compatible formats:  
DVD/SVCD/VCD/HDCD/MP3/MP4/WMA/CDDA/Picture-CD/JPEG/  
CD-R/ -RW/DVD±R/±RW playback  
Dimensions  
178 x 175 x 50 mm / 1.8 kg  
(W x D x H) / weight:  
ESP function:  
40 sec. for Audio CD, 120 sec. for MP3  
Working temperature -10- +60℃  
range:  
FM Stereo Radio  
Frequency range:  
Usable sensitivity:  
Preset memory  
stations:  
87.5 – 107.9 MHz  
15dB  
18  
AM section  
Frequency range:  
Preset memory  
stations:  
530 kHz - 1710 kHz  
12  
Audio specification  
Maximum output:  
10 Vrms (+/- 3 dB)  
Frequency response: 20 Hz - 20 KHz  
S/N ratio(A-vtd):  
DSP sound effect:  
Line out  
68 dB  
Classic, Rock, Pop, Flat and none  
4 channel RCA line-out  
1 channel Subwoofer pre-out  
Specifications are subject to change without notice. Mass and dimension are approximate.  
Manual version: March 2010  
Page- 23  

Raypak H 0066B User Manual
Plantronics Bluetooth Headset P161N User Manual
Pioneer DEH P6600 User Manual
Philips RI1760 User Manual
Philips CEM210 User Manual
Panasonic AG DVX100B User Manual
Nuvo 500 User Manual
Newcon Optik NIGHT VISION ATTACHMENT NVS 33 User Manual
NEC MultiSync LCD1860NX User Manual
JVC KS AX6550 User Manual