Important Recycle Instructions:
Lamp(s) inside this product contain mercury. This product may
contain other electronic waste that can be hazardous if not disposed of
properly. Recycle or dispose in accordance with local, state, or federal Laws.
For more information, contact the Electronic Industries Alliance at
WWW.EIAE.ORG. For lamp specific disposal information check
WWW.LAMPRECYCLE.ORG.
Table of Contents
Usage Notice
Precautions........................................................................................2
Introduction
About Planar’s PT1710MX.................................................................3
Touch Screen for PT1710MX……………………………………………..4
Package Overview.............................................................................5
Installation
Product Overview...............................................................................6
VESA Mount for your Monitor…………………………………………….9
Start Your Installation…………………………………………………….10
Connecting the Display………………………………..…………………11
User Controls
Front Panel Controls........................................................................13
How to Use the OSD Menus ............................................................14
On-Screen Display Menus ...............................................................15
Appendix
Troubleshooting ...............................................................................16
Warning Signal.................................................................................17
Product Dimensions.........................................................................18
Compatibility Modes.........................................................................19
Touch Screen Driver Installation………………………………………..20
Product Registration and Technical Support…………………………..23
Usage Notice
Warning- To prevent the risk of fire or shock hazards, do not
expose this product to rain or moisture.
Warning- Please do not open or disassemble the product as
this may cause electric shock.
Precautions
Follow all warnings, precautions and maintenance as recommended
in this user’s manual to maximize the life of your unit.
Do:
ꢀ
Turn off the product before cleaning.
ꢀ
Touch screen surface may be cleaned using a soft clean cloth
moistened with mild window glass commercial cleaners or 50/50
mixture of water and isopropyl alcohol.
ꢀ
ꢀ
ꢀ
Use a soft cloth moistened with mild detergent to clean the display
housing.
Use only high quality and safety approved AC/DC adapter that
comes with your monitor.
Disconnect the power plug from AC outlet if the product is not going
to be used for an extended period of time.
Don’t:
ꢀ
Do not touch the LCD Display screen surface with sharp or hard
objects.
ꢀ
ꢀ
Do not use abrasive cleaners, waxes or solvents for your cleaning.
Do not operate the product under the following conditions:
- Extremely hot, cold or humid environment.
- Areas susceptible to excessive dust and dirt.
- Near any appliance generating a strong magnetic field.
- In direct sunlight.
Introduction
About Planar’s PT1710MX
The PT1710MX is a 17” flat panel screen with an active matrix,
thin-film transistor (TFT) liquid crystal display (LCD).
Features include:
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Direct Analog signal input
Active matrix TFT LCD technology
1280x1024 SXGA resolution
17” viewable display area
31.5 ~ 80 kHz horizontal scan
56 ~ 75 Hz high refresh rate
0.264mm x 0.264mm Pixel pitch
Auto adjustment function
Multilingual OSD user controls
VESA DPMS power saving
Kensington security slot
100 mm VESA mount
Removable base for flexible mounting solutions.
5-wire Resistive touch screen with dual RS-232 Serial/USB controller
Built-in Speakers-1W/channel.
Touch Screen for PT1710MX
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Analog 5-wire resistive touch screen for finger and stylus input
Surface: Anti-glare treatment
Interface: Dual RS-232 Serial/USB controller
Durability: 35 million touches at a single point
Hardness of surface: 2H MIN (As provided in JIS K5400)
Operating force: 0.10~1.96N(10g~200g when using a silicon tipped pen
with a 3 mm radius and a hardness of 60)
ꢀ
ꢀ
Transmittance: 76% (Typ.)
Driver: Supports Microsoft Windows® VISTA, XP, 2000, ME, 98, NT4.0,
CE, XP Embedded, Linux, Apple® Mac OS
Package Overview
LCD Display
Power Adapter
Power Cord
VGA Signal Cable
Audio-in Cable
USB Cable
RS-232 Cable
Landing Strip
Touchscreen Driver
Installation CD-ROM
User’s Guide
Installation
Product Overview
ꢁ
Front View
ꢁ
Back View
ꢀ Connector Ports “A”
VGA
input
RS-232
input
DC
Power-in
Audio
input
ꢀ Connector Ports “B”
USB
ꢁ
Kensington Security Slot
The monitor can be secured to your desk or any other fixed object with
Kensington lock security products. The Kensington lock is not included.
VESA Mount Your Monitor
This monitor conforms to the VESA Flat Panel Mounting Physical Mounting
Interface Standard which defines a physical mounting interface for flat panel
monitors, and corresponding standards for flat panel monitor mounting
devices, such as wall and table arms. The VESA mounting interface is
located on the back of your monitor.
To mount the monitor on a swing arm or other mounting fixture, follow the
instructions included with the mounting fixture to be used.
Warning!
Please select the proper screws!
The distance between the back cover surface and the bottom of the
screw hole is 8mm. Please use M4 screw diameter with a maximum
length of 8 mm.
Start Your Installation
ꢀ Remove the Back Cover
Please follow these instructions to remove the cover on the back panel of
the LCD so that you can connect the cables in “Connector Ports A.”
1. To remove the back cover, follow the arrows in Figure A and press with
both your thumbs. The cover should be removed by pressing firmly
along the edges while pulling on the cover.
2. Follow the instructions on P. 11 ( Figure 11.1 ) to connect the cables in
“Connector Ports A.”
3. Fix the cover back to the LCD by pressing firmly until the tabs snap into
place. You may also keep the cables in order by using the cable
organizer.
ꢁ
Connecting the Display (Figure 11.1)
To setup this display, please refer to the following figure and procedures.
1. Be sure all equipment is turned off.
2. Connect the DC power cord to the power connector on the monitor; plug
one end of the AC power cord into the power adapter, and the other end
into an electrical outlet (11.1 ).
ꢂ
3. Connect the VGA signal cable from the display’s VGA input connector to
the 15-pin connector of your host computer and tighten the screws
(11.1ꢁ).
4. Connect the Audio-In cable from the audio input port of your display to
the Audio-out port of your computer (11.1ꢂ).
5. Configure the touch screen. Refer to the “Touch Screen Driver
Installation section on page 20.
6. Once the touch screen is configured, the monitor is ready for use.
To ensure the LCD display works well with your computer, please
configure the display mode of your graphics card to make it less
than or equal to 1280 x1024 resolution and make sure the timing
of the display mode is compatible with the LCD display.
We have listed the compatible “Video Modes” of your LCD display
in the appendix for your reference.
Figure 11.1
User Controls
Front Panel Controls
Control
Function
No / Icon
Menu button
Display the OSD menus
ꢃ MENU
Select – To select the adjustment items from
OSD menus.
Select/Auto
ꢁSELECT/AUTO
Auto – To activate the “Auto Adjustment”
function to obtain an optimum image.
1.Decreases the brightness of the display
image.
2.Decreases value of the adjustment items.
Brightness
Minus/Minus
ꢂ
ꢄ
ꢀ
ꢁ
1. Increases the brightness of the display
image.
2. Increases value of the adjustment items.
Brightness
Plus/Plus
Switches on/off the power of the LCD
display.
Power Switch
Power LED
ꢅ
ꢆ
1. Green indicates the display is turned on.
2. Amber indicates the display is in
power-saving mode.
14
How to Use the OSD Menus
1. Press the "MENU" button to pop up the “on-screen menu” and to select
among the four Main Menus.
2. Choose the adjustment items by pressing the “Select/Auto” button.
3. Adjust the value of the adjustment items by pressing the “ꢀ”or “ꢁ“ button.
4. The OSD menu will automatically close, if you have left it idle for a
pre-set time.
5. To disable the OSD menu buttons, please follow the instructions below:
(Please note: the monitor has to be ON with a valid signal preset)
a. Press and hold the “-“ and “Menu” key simultaneously for 4 seconds.
b. The wording “OSD Locked” will appear for 4 seconds on the monitor.
This indicates that all the front buttons, with the exception of the
power button, are now disabled.
6. To enable the OSD menu buttons, please follow the instructions below.
(Please note: the monitor has to be ON with a valid signal present.)
a. Press and hold the “-“ and “Menu” key simultaneously for 4 seconds.
b. The wording “OSD Unlocked” will appear for 4 seconds on the
monitor. This indicates that all the front buttons are now enabled.
15
On-Screen Display Menus
Main OSD Menu:
MAIN MENU SUB MENU
Auto-Adjustment
Function Description
Remark
Choose this function to obtain an optimum
image
No/Yes
0-100
.
Contrast
Adjustthecontrastofthedisplayimage.
Default 50
Default 70
Brightness
Adjuststhe brightnessofthe image.
0-100
0-100
0-100
Horizontal Position
Vertical Position
Clock
Changes the horizontalposition ofthe image.
Changes the vertical position of the image.
Default 50
Default 50
Default 50
Changes the displaydatafrequencyto match
the frequency ofyour graphiccard.When you
0-100
0-63
are experiencing verticalflickering bar
,
use
this functiontomakeanadjustment.
Phase
Synchronizes the signal timing of the display
to that of the graphic card. When you are
experiencing vertical flickering image, use
thisfunction to makeanadjustment.
Display Mode
Selectthisfunctiontoviewthe display
ADJ
5-60
resolution, vertical refresh, and horizontal
scan of the current mode
Adjuststhetime periodfor OSD menu to
disappear
Choose the language you need.
.
OSD Off-Time
Default 30
.
Language
English /
Francais
Deutsch /
Espanol
Default English
Italiano /
Japanese
Sharpness
Reset
Adjust the sharpness of the image
.
Default 3
1-4
Returnsthe displayparametersofthecurrent
mode to itsfactorydefault settings.
No/Yes
Volume
Mute
Controls the sound volume
.
Default 20
0-32
Disables the sound immediately
.
No/Yes
Color Setting
9300K /
6500K
Adjuststhecolortemperature.
Default Preset
Preset /
Custom
Color
Adjustment-Red
Color
It allows you to adjustthe red color ofthe display
.
Default 100
Default 100
0-100
0-100
0-100
It allows you to adjust the green color of the
Adjustment-Green
display
.
Color
Adjustment-Blue
It allowsyou to adjustthe blue color ofthe display
.
Default 100
16
Appendix
Troubleshooting
If you are experiencing trouble with the LCD display, refer to the following. If
the problem persists, please contact your local dealer or our service center.
Problem: No image appears on screen.
ꢀCheck that all the I/O and power connectors are correctly and well
connected as described in the “Installation” section.
ꢀMake sure the pins of the connectors are not crooked or broken.
Problem: Partial Image or incorrectly displayed image.
ꢀCheck to see if the resolution of your computer is higher than that of the
LCD display.
ꢀReconfigure the resolution of your computer to make it less than or equal
to 1280 x 1024.
Problem: Image has vertical flickering line bars.
ꢀUse "Clock" to make an adjustment.
ꢀCheck and reconfigure the display mode of the vertical refresh rate of your
graphic card to make it compatible with the LCD display.
Problem: Image is unstable and flickering
ꢀUse "Phase" to make an adjustment.
Problem: Image is scrolling
ꢀCheck and make sure the VGA signal cable (or adapter) is securely
connected.
ꢀCheck and reconfigure the display mode of the vertical refresh rate of your
graphics card to make it compatible with the LCD Display.
Problem: Vague image (characters and graphics)
ꢀUse "Clock" to make an adjustment. If this problem still exists, use “Phase”
to make an adjustment.
17
Warning Signal
If you see warning messages on your LCD screen, this means that
the LCD display cannot receive a clean signal from the computer
graphics card.
There may be two sources for this problem. Please check the cable
connections or contact Planar for more information.
ꢀ
ꢀ
No Signal
This message means that the LCD Display has been powered on but it
cannot receive any signal from the computer graphics card. Check all the
power switches, power cables, and VGA signal cable.
Out of Range
This message means that the signal of the computer graphic card is not
compatible with the LCD display. When the signal is not included in the
“Video Modes” list we have listed in the Appendices of this manual, the
LCD display will display this message.
18
Product Dimensions
19
Compatibility Modes
V. Frequency H. Frequency
(Hz)
Mode
Resolution
(kHz)
IBM VGA
IBM VGA
IBM VGA
640 x 350
720 x 400
640 x 480
640 x 480
640 x 480
800 x 600
800 x 600
800 x 600
800 x 600
1024 x 768
1024 x 768
1024 x 768
1280X1024
1280X1024
640 x 480
832 x 624
1024 x 768
70
31.5
70
60
72
75
56
60
72
75
60
70
75
60
75
67
75
75
31.5
31.5
37.9
37.5
35.2
37.9
48.1
46.9
48.4
56.5
60.0
64.0
80.0
35.0
49.7
60.2
VESA VGA
VESA VGA
VESA SVGA
VESA SVGA
VESA SVGA
VESA SVGA
VESA XGA
VESA XGA
VESA XGA
VESA SXGA
VESA SXGA
Apple Mac II
Apple Mac
Apple Mac
20
Touch Screen Driver Installation
The PT1710MX is available with both RS-232 and USB connections. The
PT1710MX is Microsoft® Windows® HID (Human Interface Device)
compatible if you use the USB touch screen interface. No additional
software driver is required for general operation of the touch screen. A
calibration tool can be installed for improved touch position accuracy. See
“Optional Resistive Calibration Tool Install” section for more information.
The touch driver is located on the enclosed CD-ROM for these operating
systems: Windows® VISTA, XP, 2000, ME, 98, NT4.0, CE,
XP Embedded, Linux, Apple® Mac OS
Please note: Do not plug in both RS232 and USB cables. Doing so may
cause a driver conflict, making your touch screen idle.
Driver Installation Process:
1. Before you start to install the touch driver, please be sure the USB or the
RS-232 Serial cable is connected to the PC and LCD display.
2. Uninstall any touch screen driver that may be on your system.
3. Restart your computer.
4. Click on the appropriate link found on the CD-ROM.
5. Follow instructions as found below.
6. After installation is complete, click “Finish” to complete installation.
21
PT1710MX Optional Resistive Calibration Tool Install:
If you would like to use the Optional Resistive Calibration Tool, follow the
instructions below:
1. Open the CD-Rom.
2. Select the Monitor Size and then Model Name
3. Click on the “Load Utility” button that appears to the right of the
Model Name.
4. The HID calibration tool will automatically open. From here the user
can choose to do the following:
a. 4 Points Calibration
b. 9 Points Linearization
c. 25 Points Linearization
d. Clear
e. Draw Test
f. Advanced. In the Advanced settings area the user may do
the following:
i. Adjust the Double Click Area
ii. Enable auto right click and adjust the auto right click
time
iii. Choose to be either in the HID Mouse Mode or HID
Digitizer Mode (Windows® Vista only)
iv. Simply click the “Apply” button once the settings are
finalized.
22
If you are using a PC running Windows® Vista, XP or 2000 operating system,
follow the instructions below.
Using the RS232 connection:
1. Be sure that RS232 cable is connected from the computer.
2. Power on the computer.
3. Load the touch screen driver CD.
4. Follow the step-by-step instructions as shown on pop-up windows.
Using the USB connection:
1. Be sure that USB cable is connected from the computer.
2. Power on the computer.
3. Load the touch screen driver CD.
4. Follow the step-by-step instructions as shown on pop-up windows.
If you are using a PC running Windows® XP Embedded, follow the
instructions below:
1. Power on the computer.
2. Make sure that the RS232 or USB cable is connected to the computer.
3. Be sure that your EWF (Enhanced Write Filter) is disabled. If your EWF
is enabled, please disable the EWF by using the EWF Manager
command.
4. Once the EWF is disabled click on the XP driver on the CD and follow the
step-by-step instructions as shown on the pop-up windows.
23
Product Registration and Technical Support
Register Your Planar Products Today
Thank you for choosing Planar. To assure you receive all the benefits of your
Planar product and services, register your Planar product today. Visit our website
Cables, Replacement Lamps, Accessories
To find cables, replacement lamps and accessories for your Planar projector,
LCD monitor, touch screen or other Planar products visit our online store at
Technical Support
operations manuals, touch screen drivers, warranty information and access to
Planar’s Technical Library for online troubleshooting.
Online chat service is available Monday through Friday from 12am to 6pm
Pacific Time.
To speak with Planar Customer Support please have you model and serial
number available and dial:
Planar Support
Tel: 1-866-PLANAR1 (866-752-6271) or +1 503-748-5799 outside the US.
Hours: 24 hours a day, 7 days a week.
Toll or long distance charges may apply.
PT1710MX
Windows
Microsoft, Inc.
WWW.EIAE.ORG
WWW.LAMPRECYCLE.ORG
1
目录
............................................................................2
Planar PT1710MX
PT1710MX
...............................................................3
...................................................................4
......................................................................................5
......................................................................................6
VESA
..................................................................9
....................................................................................10
.................................................................................11
.................................................................................13
OSD
..................................................................14
.............................................................................15
...................................................................................16
...................................................................................17
2
....................................................................................18
.................................................................................19
...................................................................20
...................................................................23
3
使用须知
-
-
使用前注意事项
ꢃ
ꢃ
50/50
ꢃ
ꢃ
/
ꢃ
AC
ꢃ
ꢃ
ꢃ
/
LCD
4
5
介绍
Planar PT1710MX简介
PT1710MX 17”
LCD
TFT
ꢃ
ꢃ
ꢃ
ꢃ
ꢃ
ꢃ
ꢃ
ꢃ
ꢃ
ꢃ
ꢃ
ꢃ
ꢃ
TFT LCD
1280x1024 SXGA
17”
31.5 80 kHz
56 75 Hz
0.264mm x 0.264mm
OSD
VESA DPMS
Kensington
100 mm VESA
6
ꢃ
ꢃ
5
RS-232
/USB
–1W/
7
PT1710MX触摸屏
ꢃ
ꢃ
ꢃ
ꢃ
ꢃ
ꢃ
5
RS-232
/USB
3500
2H MIN JIS K5400
0.10 1.96N
3 mm
60
10g
200g
ꢃ
ꢃ
76%
Windows® VISTA, XP, 2000, ME, 98, NT4.0, CE,
XP Embedded, Linux, Apple® Mac OS
8
组件概览
VGA
USB
RS-232
9
安装
产品概述
ꢁ
ꢁ
10
11
ꢁ
A
VGA
RS-232
DC
ꢁ
B
USB
12
ꢁ
Kensington
Kensington
Kensington
13
显示器的VESA安装
VESA
VESA
14
8 mm
8 mm M4
15
开始安装
ꢁ
“
A”
1.
A
2.
3.
11
11.1
A
LCD
16
17
ꢁ
11.1
1.
2.
DC
AC
11.1ꢃ
3.
4.
VGA
VGA
15
(11.1ꢁ)
(11.1ꢂ)
5.
6.
20
1280 x 1024
LCD
LCD
“
”
18
11.1
19
用户控制
前面板控制
/
OSD
ꢃ MENU
—
—
OSD
“
/
”
ꢁSELECT/AUTO
1.
2.
1.
2.
ꢂ
ꢄ
ꢀ
ꢁ
/
/
/
LCD
ꢅ
ꢆ
1.
2.
LED
20
21
如何使用OSD菜单
1.
2.
3.
4.
5.
MENU
on-screen menu
Select/Auto
ꢂ
ꢃ
OSD
OSD
a.
“-”
“Menu”
4
b. OSD Locked OSD
4
6.
OSD
a.
“-” “Menu”
4
b. “OSD Unlocked” OSD
4
22
屏幕显示菜单
OSD
MENU
Auto
(
-
Adjustment
)
/
0-100
0-100
Contrast(
)
50
70
Brightness(
)
Horizontal Position
0-100
0-100
50
50
(
)
Vertical Position
(
)
0-100
0-63
Clock(
)
50
Phase(
)
Display Mode
ADJ
5-60
(
)
OSD Off
(OSD
-Time
OSD
30
)
English /
Francais
Deutsch /
Espanol
Italiano /
Language(
)
English
1-4
/
Sharpness(
Reset(
)
3
)
0-32
/
Volume(
)
20
Mute(
)
23
Color Setting
9300K/ 6500K/
/
(
)
Color adjustment-Red
0-100
100
(
-
)
Color adjustment-Green
0-100
0-100
100
100
(
-
)
Color Adjustment-Blue
(
-
)
24
附录
故障排除
ꢃ
ꢃ
I/O
“
”
ꢃ
ꢃ
1280 x 1024
ꢃ
ꢃ
Clock
LCD
ꢃ
Phase
ꢃ
ꢃ
VGA
25
ꢃ
Clock
Phase
26
警告信号
Planar
ꢃ No Signal
VGA
ꢃ Out of Range
LCD
“
”
“
”
27
产品尺寸
28
兼容性模式
(Hz)
(kHz)
IBM VGA
640 x 350
720 x 400
640 x 480
640 x 480
640 x 480
800 x 600
800 x 600
800 x 600
800 x 600
1024 x 768
1024 x 768
1024 x 768
1280X1024
1280X1024
640 x 480
832 x 624
1024 x 768
70
31.5
IBM VGA
70
60
72
75
56
60
72
75
60
70
75
60
75
67
75
75
31.5
31.5
37.9
37.5
35.2
37.9
48.1
46.9
48.4
56.5
60.0
64.0
80.0
35.0
49.7
60.2
IBM VGA
VESA VGA
VESA VGA
VESA SVGA
VESA SVGA
VESA SVGA
VESA SVGA
VESA XGA
VESA XGA
VESA XGA
VESA SXGA
VESA SXGA
Apple Mac II
Apple Mac
Apple Mac
29
触摸屏驱动程序安装
PT1710MX
RS-232 USB
USB
PT1710MX
Microsoft Windows HID
Windows® VISTA, XP, 2000, ME, 98, NT4.0, CE,
XP Embedded, Linux, Apple® Mac OS
RS232 USB
1.
USB RS232
PC
LCD
2.
3.
4.
CD-ROM
30
5.
6.
” Finish
31
32
33
产品注册和技术支持
立即注册您的 Planar 产品
Planar
Planar
Planar
缆线、备用灯及其他附件
Planar
Planar
Planar
技术支持
Planar
Planar
12am 6pm
Planar
Planar
: 1-866-PLANAR1 (866-752-6271)
24 7
+1 503-748-5799
产品中有毒有害物质或元素的名称及含量
(Pb)
(Hg)
(Cd)
(Cr(VI))
(PBB)
(PBDE)
O
X
X
X
O
X
X
X
O
O
O
O
O
O
X
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O:
SJ/T 11363-2006
X:
SJ/T
11363-2006
/
EIP
Planar Systems, Inc.
Customer Service
24x7 Online Technical Support: http://www.planar.com/support
1195 NW Compton Drive
Beaverton, OR 97006-1992
Tel: 1-866-PLANAR1 (866-752-6271) or +1 503-748-5799 outside the United States.
Hours: 24 hours a day, 7 days a week
© 2009 Planar Systems, Inc. 4/09 Planar is a registered trademark of Planar Systems, Inc.
Other brands and names are the property of their respective owners.
Technical information in this document is subject to change without notice.
***************************************************************************************
Planar Systems, Inc.
24x7
1195 NW Compton Drive
Beaverton, OR 97006-1992
1-866-PLANAR1 (866-752-6271) +1 503-748-5799
24 7
© 2009 Planar Systems, Inc. 4/09 Planar Planar System, Inc.
P/N:36.56905G019 Rev.A
020-0555-00C
|