Pioneer CX 958 User Manual

Service

Manual

DEH-2130R/X1M/EW

ORDER NO.

CRT2434

HIGH POWER CD PLAYER WITH RDS TUNER

DEH-2130R

X1M/EW

DEH-2100R

X1M/EW

- This service manual should be used together with the following manual(s):

Model No.

CX-958

Order No.

CRT2423

Mech. Module Remarks

S8.1

CD Mech. Module:Circuit Description, Mech.Description, Disassembly

CONTENTS

1. SAFETY INFORMATION ............................................2

2. EXPLODED VIEWS AND PARTS LIST.......................3

3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM.....8

4. PCB CONNECTION DIAGRAM ................................26

5. ELECTRICAL PARTS LIST ........................................36

6. ADJUSTMENT..........................................................41

7. GENERAL INFORMATION .......................................45

7.1 DIAGNOSIS ........................................................45

7.1.1 TEST MODE..............................................45

7.1.2 DISASSEMBLY .........................................48

7.2 PARTS .................................................................52

7.2.1 IC................................................................52

7.2.2 DISPLAY....................................................59

7.3 OPERATIONAL FLOW CHART...........................60

8. OPERATIONS AND SPECIFICATIONS.....................61

PIONEER CORPORATION

4-1, Meguro 1-Chome, Meguro-ku, Tokyo 153-8654, Japan

PIONEER ELECTRONICS SERVICE INC. P.O.Box 1760, Long Beach, CA 90801-1760 U.S.A.

PIONEER ELECTRONIC [EUROPE] N.V. Haven 1087 Keetberglaan 1, 9120 Melsele, Belgium

PIONEER ELECTRONICS ASIACENTRE PTE.LTD. 253 Alexandra Road, #04-01, Singapore 159936

C PIONEER CORPORATION 1999

K-ZZA. NOV. 1999 Printed in Japan

DEH-2130R,2100R

2. EXPLODED VIEWS AND PARTS LIST

2.1 PACKING

NOTE:

- Parts marked by “*” are generally unavailable because they are not in our Master Spare Parts List.

- Screws adjacent to ∇ mark on the product are used for disassembly.

(1) PACKING SECTION PARTS LIST

Mark No. Description

Part No.

Mark No. Description

Part No.

1 Cord Assy

2 Screw

3 Handle

4 Bush

CDE6123

CBA1002

CNC5395

CNV3930

E36-615

7-5 Passport

7-6 Warranty Card

8 Carton

9 Contain Box

10 Protector

CRY1013

CRY1157

See Contrast table(2)

CHP2243

5 Polyethylene Bag

6 Polyethylene Bag

7-1 Polyethylene Bag

7-2 Owner's Manual

7-3 Owner's Manual

7-4 Installation Manual

CEG-162

CEG1116

CRD3137

CRD3138

CRD3139

11 Protector

12 Case Assy

CHP2244

CXB3520

(2) CONTRAST TABLE

DEH-2130R/X1M/EW and DEH-2100R/X1M/EW are constructed the same except for the following:

Part No.

Mark No. Symbol and Description DEH-2130R/X1M/EW DEH-2100R/X1M/EW

8 Carton

9 Contain Box

CHG3951

CHL3951

CHG3950

CHL3950

- Owner's Manual, Installation Manual

Model

Part No.

CRD3137

CRD3138

CRD3139

Language

English, Spanish, German

French, Italian, Dutch

English, Spanish, German, French, Italian, Dutch

DEH-2130R/X1M/EW

DEH-2100R/X1M/EW

DEH-2130R,2100R

2.2 EXTERIOR

DEH-2130R,2100R

(1) EXTERIOR SECTION PARTS LIST

Mark No. Description

Part No.

Mark No. Description

Part No.

1 Screw

2 Screw

3 Screw

4 Screw

5 Cord Assy

BMZ26P120FMC

BSZ26P060FMC

BSZ30P060FMC

BSZ30P120FMC

CDE6123

36 Spring

37 Spring

38 Spring

39 Bracket

40 Holder

CBH1835

CBH2208

CBH2367

CNC6791

CNC8042

6 Cable

7 Fuse(10A)

8 CD Mechanism Module(S8.1) CXK5203

9 Cover

CDE6160

CEK1136

41 Cover

42 Panel

43 Arm

44 Arm

45 Arm

CNM6276

See Contrast table(2)

CNV4692

CNV4728

CNC8367

CNC8884

10 Holder

CNV5576

11 Spacer

CNM4913

CNM6224

CNM6386

46 Screw

47 Detach Grille Assy

48 Screw

49 Button(Detach)

50 Button(+, -)

IMS20P030FZK

See Contrast table(2)

BPZ20P100FZK

See Contrast table(2)

12 Insulator

13 Insulator

14 •••••

15 Tuner Amp Assy

CWM6764

16 Screw

17 Screw

18 Screw

19 FM/AM Tuner Unit

20 Holder

ASZ26P080FMC

BPZ26P080FMC

BSZ26P160FMC

CWE1500

51 Chassis Unit

52 Screw

53 IC(IC302)

54 Transistor(Q904, 981)

55 Button(Source)

See Contrast table(2)

ISS26P055FUC

TDA7384

2SD2396

CAC6494

CNC7532

21 Pin Jack(CN301)

22 Terminal(CN403)

23 Connector(CN901)

24 Connector(CN601)

25 Connector(CN605)

CKB1041

CKF1059

CKM1299

CKS3581

CKS3838

56 Button(1-6)

57 Button(B, A, Cross)

58 Button(Eject)

59 Spring

CAC6275

See Contrast table(2)

CAC6277

CBH2210

60 Cover

See Contrast table(2)

26 Antenna Jack(CN402)

27 Holder

28 Holder

29 Holder

30 Holder

CKX1056

CNC7533

CNC8041

CNC8043

CNC8588

61 Keyboard Unit

62 LCD(LCD1801)

63 Connector(CN1801)

64 Holder

See Contrast table(2)

CAW1559

CKS3580

CNC8517

CNV5954

65 Rubber

31 Insulator

32 Heat Sink

33 Holder Unit

34 Case Unit

35 Button

CNM5967

CNR1506

CXB2687

CXB4033

CAC4836

66 Lighting Conductor

67 Rubber

68 Grille Unit

69 Cap

CNV5965

CNV5966

See Contrast table(2)

CNS1472

70 Resistor

RS1/2PMF102J

(2) CONTRAST TABLE

DEH-2130R/X1M/EW and DEH-2100R/X1M/EW are constructed the same except for the following:

Part No.

Mark No. Symbol and Description DEH-2130R/X1M/EW DEH-2100R/X1M/EW

42 Panel

CNS5340

CXB4595

CAC5929

CAC6458

CXB4624

CNS5188

CXB4592

CAC5789

CAC6273

CXB4623

47 Detach Grille Assy

49 Button(Detach)

50 Button(+, -)

51 Chassis Unit

57 Button(B, A, Cross)

60 Cover

61 Keyboard Unit

68 Grille Unit

CAC6459

CNS5773

CWM6779

CXB4612

CAC6276

CNS5772

CWM6778

CXB4611

DEH-2130R,2100R

2.3 CD MECHANISM MODULE

DEH-2130R,2100R

- CD MECHANISM MODULE SECTION PARTS LIST

Mark No. Description

1 Control Unit

Part No.

Mark No. Description

Part No.

CWX2411

CKS2192

CKS2193

CKS2773

CKS3486

46 •••••

47 Ball

48 Belt

49 Roller

50 Arm

2 Connector(CN802)

CNR1189

CNT1086

CNV4509

CNV6037

3 Connector(CN801)

4 Connector(CN701)

5 Connector(CN101)

6 Screw

7 Screw

8 Screw(M2x3)

9 Screw(M2x5)

10 Screw

BMZ20P030FMC

BSZ20P040FMC

CBA1077

EBA1028

CBA1243

51 Arm

52 Arm

53 Arm

54 Guide

55 Guide

CNV5247

CNV5248

CNV5249

CNV5254

CNV5255

11 Screw(M2x4)

12 Washer

13 Washer

14 Washer

15 •••••

CBA1362

CBF1037

CBF1038

CBF1060

56 Gear

57 Gear

58 Guide

59 Damper

60 Arm

CNV5257

CNV5256

CNV6176

CNV6174

CNV6096

16 Spring

17 Spring

18 Spring

19 Spring

20 Spring

CBH2079

CBH2117

CBH2314

CBH2110

CBH2282

61 Arm

62 Arm

63 Guide

64 Guide

65 •••••

CNV6031

CNV6211

CNV6012

CNV5510

21 Spring

22 •••••

23 Spring

24 Spring

25 Spring

CBH2318

66 Guide

67 Clamper

68 Gear

69 Motor Unit(M1)

70 Screw Unit

CNV5751

CNV6013

CNV5813

CXB2190

CXB4726

CBH2324

CBH2118

CBH2161

26 Spring

27 Spring

28 Spring

29 Spring

30 Spring

CBH2163

CBH2189

CBH2249

CBH2260

CBH2262

71 Chassis Unit

72 Gear Unit

73 Arm Unit

74 Motor Unit(M2)

75 Lever Unit

CXB4797

CXB4728

CXB4729

CXB2195

CXB4730

31 Bracket

32 Spring

33 Connector

34 Connector

35 Shaft

CNC8568

CBL1369

CDE5531

CDE5532

CLA3304

76 Arm Unit

77 Motor Unit(M3)

78 Arm Unit

79 Bracket Unit

80 Screw

CXB4731

CXB2562

CXB4732

CXB4795

JFZ20P025FMC

36 Screw(M2.6x6)

37 Frame

38 Frame

39 Lever

40 Arm

CBA1458

CNC8565

CNC8749

CNC7546

CNC8663

81 Screw

82 Washer

83 Pickup Unit(Service)(P8) CXX1285

84 Screw

JGZ17P025FZK

YE20FUC

IMS26P030FMC

CNX2982

85 PCB

41 Bracket

42 •••••

CNC8567

86 Photo-transistor(Q1, 2)

87 Damper

CPT230SX-TU

CNV6175

43 Spacer

44 Sheet

45 •••••

CNM3315

CNM6659

88 Rack

89 Spring

CNV6014

CBH2315

DEH-2130R,2100R

3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM

3.1 BLOCK DIAGRAM

TUNER AMP ASSY

Q476

Q472

Q474

LDET

FM/AM TUNER UNIT

TMUTE

FM/AM 1ST IF 10.7MHz

T51 Q51 CF51 CF52 CF53

FM FRONT END

FM MPX

ANTENNA

CN402

Q477

IC 2 PM4008A

RDS

VDD

34 33 41 44 11 12 13

DECODER

FM/AM

COMP

LDET

IC 701

PM4009A

MIXER.IF AMP DET

IC 1

PML002A

Q201 Q204

AM RF

33 32 45

55 57

61 74

X702

CF202

EEPROM

IC 3

BR9010FV

AM 2ND IF 450kHz

Q202

VDD

VCC

22 10 14

12 15 16

Q411

LOCL

VDD

VCC

CONTROL UNIT

PICKUP UNIT(SERVICE)(P8)

Q101

CN701

CN605

CDL

CN101

LD+

L_OUT

A+C/F

B+D/E

HOLOGRAM

UNIT

IC 201

UPD63711GC

FOP

TOP

FO+

TO+

FOCUS ACT

X201

TRACKING ACT

RF-AMP, DSP,

SERVO, DAC

IC 301

BA5985FM

TD/FD

SD/MD

FOP

TOP

HOME

SPINDLE

S801

HOME

MOTOR

SOP

SOM

COP

CN801

CARRIAGE

MOTOR

CDLOAD

CDEJET

CONT

CDLOAD

EJET

COM

LOP

LOM

FWD

REV

CONT

MUTE

MOTOR

CN802

EJTSNS

DSCSNS

EJTD

DINC

CLAMP

SELECT

SENSE

Q981

Q982

D803 D802 D801

B.U

S802

CLAMP

DISC SENSE

+5V REGULATOR

IC 701

BA05SFP

VDD

PHOTO UNIT(S8)

CD5VON

VDCONT

DEH-2130R,2100R

TMUTE

LDET

CN301

REAR L CH

Q346

FM/AM

SYSTEM

CONTROLLER

IC 601(1/2)

PE5090A

NL1

SDBW

TUNPCE

TUNPCK

TUNPCE2

TUNPDO

TUNPDI

LOCL

PDIO

VST

VCK

VDT

Q353

B.U

Q903

BACKUP

B.U

VDD

FUSE

10A

BACK UP

GND

VST/ VCK/ VDT

POWER AMP

IN1

IN2

FL–

FL+

ELECTRONIC VOLUME/

SOURCE SELECTOR

FL–

Fout

Rout

IC 302

TDA7384

FL+

RL–

IC 301

RL–

SN761029DL

RL+

MUTE

STBY

B.REMOTE

B.REM

Q351 MUTE

Q902

asens

bsens

ACC

B.U

ASENS

Q901

TELIN

CELLULAR MUTE

BSENS

CELLULAR MUTE

Q951

SYSTEM

CONTROLLER

TELIN

IC 601(2/2)

PE5090A

Q942 Q941

SYSPW

CDLOAD

CDEJECT

CONT

RR RR

BACK

FR FR

FL FL

REM

MUTE

RL RL

EJTSNS

DSCSNS

ACC

GND

KEYBOARD UNIT

CLAMP

CN1801

CN601

KYDT

DPDT

KYDT

DPDT

LCD

VDCONT

RESET

IC 602

S–80834ANY

VDD

RESET

VDD

VLCD

SWVDD

Q650

LCD DRIVER

CD5VON

IC 1801

PD6293A

KEY MATRIX

X1801

DEH-2130R,2100R

3.2 OVERALL CONNECTION DIAGRAM(GUIDE PAGE)

Note: When ordering service parts, be sure to refer to “EXPLODED VIEWS AND PARTS LIST” or “ELECTRICAL PARTS

LIST”.

Large size

SCH diagram

A-a

A-b

A-a

A-b

Guide page

B ^{FM/AM TUNER UNIT}

FM(100%):-15.5dBs

AM (30%):-26dBs

A-a

A-b

Detailed page

CD:+4.

FM(100%):-15

AM (30%):-26

162

4.194MHz

CSS1047

SYSTEM CONTROLLER

R699

0R0

104

KEYBOARD

UNIT

NOTE :

Symbol indicates a resistor.

No differentiation is made between chip resistors and

discrete resistors.

For resistors and capacitors in the circuit diagrams, their resistance values or

capacitance values are expressed in codes:

Symbol indicates a capacitor.

No differentiation is made between chip capacitors and

discrete capacitors.

Ex. *Resistors

Code

123

Practical value

12k ohms

10k ohms

The > mark found on some component parts indicates

the importance of the safety factor of the part.

Therefore, when replacing, be sure to use parts of

identical designation.

103

*Capacitors

Code

103

101/10

Practical value

0.01µF

100µF/10V

DEH-2130R,2100R

A-b

CD:+10.1dBs

FM(100%):+6.5dBs

AM (30%):-3dBs

TUNER AMP ASSY

4.1dBs

5.5dBs

6dBs

SOURCE SELECTOR/

E.VOL

POWER AMP

CD:+36.1dBs

FM(100%):+32.5dBs

AM (30%):+23dBs

CD:+10.1dBs

FM(100%):+6.5dBs

AM (30%):-3dBs

CEK1136

600µH

Reset

VD REGULATOR

CD:+4.1dBs

102(1/2W)

CELLULAR MUTE

RR RR

BACK

FR FR

FL FL

REM

RL RL

ACC

GND

DEH-2130R,2100R

2 7 2

1 2 3

D S P - 2 0 1 M - S 0 0 B

A-a

DEH-2130R,2100R

C D M E C H A N I S M M

0 R 0

1 0 2

A-a

DEH-2130R,2100R

3 3 2 / 1 6

A-b

DEH-2130R,2100R

( B 2 )

C D M E C H A N I S M M

A-b

DEH-2130R,2100R

3.3 FM/AM TUNER UNIT

FM/AM TUNER UNIT

Mark Band Input Level

None

–

0dBf

F65

65dBf

125dBf

0dBµ

74dBµ

125dBµ

F125 FM

A74

A125 AM

DEH-2130R,2100R

3.4 KEYBOARD UNIT

KEYBOARD UNIT

PD6293A

LCD DRIVER,

KEY CONTROLLER

CAW1559

DEH-2130R,2100R

DISP

PTY

TA/AF

LOCAL/BSM

DEH-2130R/X1M/EW DEH-2100R/X1M/EW

IL1801-1804 CEL1638(14V 40mA) CEL1547(14V 40mA)

DEH-2130R,2100R

3.5 CD MECHANISM MODULE

CONTROL UNIT

PICKUP UNIT

(SERVICE)(P8)

CN101

RF-AMP, SE

PHOTO UNIT(S8)

Q1 CPT230SX-TU Q2 CPT230SX-TU

CN802

SPINDLE MOTOR

M3 CXB2562

CARRIAGE MOTOR

M1 CXB2190

LOADING MOTOR

CD DRIVER

M2 CXB2195

CN801

BA05SFP

5V REGULATOR

D E

DEH-2130R,2100R

SWITCHES:

CONTROL UNIT

S801 : HOME SWITCH.....ON-OFF

S802 : CLAMP SWITCH....ON-OFF

The underlined indicates the switch position.

MP, SERVO, DSP, DAC, LPF

CN701

DEH-2130R,2100R

Note:1. The encircled numbers denote measuring pointes in the circuit diagram.

2. Reference voltage

REFO:2.5V

- Waveforms

1 RFI

0.5V/div. 0.5µs/div.

1 CH1: RFI

2 CH2: MIRR

1V/div.

5V/div.

1 CH1: RFI

2 CH2: MIRR 5V/div.

1V/div.

0.5ms/div.

Normal mode: play

Test mode: Tracking open

Normal mode: The defect part

passes 800µm

→

REFO

→

REFO

→

REFO

3 CH1: FD

5 CH2: FOK

0.5V/div.

2V/div.

6 CH1: FE

7 CH2: XSI

0.5V/div.

2V/div.

3 CH1: FD

4 CH2: FO+

0.5V/div.

2V/div.

0.2s/div.

1ms/div.

0.2s/div.

Normal mode: Focus close

Test mode: No disc, Focus close

→

REFO

→

REFO

→

REFO

GND

→

8 CH1: TE

9 CH2: TD

0.5V/div.

8 CH1: TE

9 CH2: TD

0.5V/div.

8 CH1: TE

9 CH2: TD

0.5V/div.

0.5ms/div.

5ms/div.

Test mode: 32 tracks jump (FWD)

Test mode: Single jump (FWD)

Test mode: 100 tracks jump (FWD)

→

REFO

→

6 CH1: FE

3 CH2: FD

0.1V/div.

0.2V/div.

3 CH1: FD

0 CH2: MD

0.5V/div.

1V/div.

3 CH1: FD

0 CH2: MD

0.5V/div.

1V/div.

20ms/div.

0.5s/div.

Normal mode: Play

Normal mode: Focus close (12cm)

Normal mode: Focus close (8cm)

→

REFO

→

REFO

DEH-2130R,2100R

8 CH1: TE

9 CH2: TD

0.2V/div.

8 CH1: TE

! CH2: SD

0.5V/div.

0 MD

0.5V/div. 0.1s/div.

5ms/div.

20ms/div.

Normal mode: play

TEST mode: 100 Tracks jump(FWD)

Normal mode: Play (12cm)

→

REFO

→

REFO

→

REFO

@ EFM

1V/div.

5µs/div.

8 CH1: TE

# CH2: TEC

1V/div.

0 MD

1V/div.

10ms/div.

2ms/div.

Normal mode:

Normal mode: play

Test mode: Focus close

Tracking open

Long Search (12cm)

→

REFO

→

REFO

→

REFO

GND

8 CH1: TE

6 CH2: FE

0.5V/div.

$ PLCK

2V/div. 0.5µs/div.

% SCKO

2V/div.

1µs/div.

0.2s/div.

Normal mode: AGC after focus close

Normal mode: play

→

REFO

→

REFO

GND

→

REFO

GND

^ Dout

2V/div.

10µs/div.

& LRCK

2V/div. 20µs/div.

* VD

5V/div.

50ms/div.

Normal mode: play

Normal mode: No disc

→

GND

→

REFO

GND

→

REFO

GND

DEH-2130R,2100R

( CH1: R OUT 1V/div.

) CH2: L OUT 1V/div.

6 CH1: FE

3 CH2: FD

0.2V/div.

0.5V/div.

8 CH1: TE

9 CH2: TD 0.5V/div.

Normal mode: During AGC

0.2V/div.

1ms/div.

0.2ms/div.

1ms/div.

Normal mode: Play (1kHz 0dB)

Normal mode: During AGC

→

REFO

→

REFO

9 CH1: TD

⁄ CH2: HOLD 5V/div.

0.1V/div.

1 CH1: RFI

⁄ CH2: HOLD 5V/div.

1V/div.

3 CH1: FD

⁄ CH2: HOLD 5V/div.

0.5V/div.

0.5ms/div.

Normal mode: The defect part passes

800µm(B.D)

→

REFO

→

REFO

DEH-2130R,2100R

4. PCB CONNECTION DIAGRAM

4.1 TUNER AMP ASSY

TUNER AMP ASSY

CORD ASSY

NOTE FOR PCB DIAGRAMS

1. The parts mounted on this PCB

include all necessary parts for

several destination.

For further information for

respective destinations, be sure

to check with the schematic dia-

gram.

2. Viewpoint of PCB diagrams

Capacitor

Connector

SIDE A

SIDE B

Chip Part

P.C.Board

C ^CN1801

DEH-2130R,2100R

SIDE A

DEH-2130R,2100R

TUNER AMP ASSY

DEH-2130R,2100R

SIDE B

DEH-2130R,2100R

4.2 FM/AM TUNER UNIT

SIDE A

DEH-2130R,2100R

SIDE B

DEH-2130R,2100R

4.3 KEYBOARD UNIT

SIDE A

DEH-2130R,2100R

SIDE B

DEH-2130R,2100R

SIDE A

4.4 CD MECHANISM MODULE

D E

DEH-2130R,2100R

SIDE B

DEH-2130R,2100R

5. ELECTRICAL PARTS LIST

NOTES:

- Parts whose parts numbers are omitted are subject to being not supplied.

- The part numbers shown below indicate chip components.

Chip Resistor

RS1/_S___J,RS1/__S___J

Chip Capacitor (except for CQS.....)

CKS....., CCS....., CSZS.....

=====Circuit Symbol and No.===Part Name

Part No.

-------------------------

=====Circuit Symbol and No.===Part Name

--- ------ ------------------------------------------

Part No.

-------------------------

--- ------

------------------------------------------

650

703

704

901

951

Ferri-Inductor

Inductor

Ferri-Inductor

Choke Coil 600µH

Ferri-Inductor

LAU2R2K

LAU100K

LAU101K

CTH1221

LAU2R2K

Unit Number : CWM6764

Unit Name

: Tuner Amp Assy

MISCELLANEOUS

301

302

601

602

701

SN761029DL

TDA7384

TH 601

Thermistor

CCX1031

610

702

Ceramic Resonator 4.194MHz

Crystal Resonator 3.648MHz

Arrester

CSS1047

PE5090A

CSS1447

DSP-201M-S00B

CWE1500

S-80834ANY

PM4009A

AR 946

FM/AM Tuner Unit

346

351

353

411

412

Transistor

RN1610

RESISTORS

DTC114EK

DTA124EK

2SC2412K

310

311

312

313

314

RD1/4PU222J

RS1/10S272J

RS1/10S151J

472

474

475

476

477

Transistor

RN1610

2SD1757K

2SC2412K

DTA124EK

315

316

317

318

319

RS1/10S151J

RS1/10S0R0J

RS1/10S121J

RD1/4PU104J

650

901

902

903

904

Transistor

2SA1037K

2SC2412K

2SD1859

2SD2396

320

321

322

342

343

RS1/10S121J

RS1/10S101J

RS1/8S821J

905

906

941

942

951

Transistor

2SB1243

DTC114EK

2SB1243

344

345

352

353

354

RS1/10S223J

RS1/10S103J

RS1/10S331J

DTC114EK

2SA1037K

981

982

650

651

652

Transistor

Diode

2SD2396

RN46A1

1SS270

360

411

412

413

414

RD1/4PU153J

RS1/10S681J

RS1/10S103J

653

654

655

901

902

Diode

1SS270

HZS7L(C2)

S5688G

415

416

417

418

419

RS1/8S681J

RD1/4PU473J

RD1/4PU472J

RS1/10S473J

903

904

905

906

907

Diode

S5688G

HZS7L(A1)

S5688G

420

421

422

423

424

RS1/10S473J

RS1/10S681J

HZS6L(B2)

HZS9L(B3)

941

942

951

952

981

Diode

S5688G

1SS270

HZS9L(B1)

425

426

427

428

430

RS1/10S393J

RS1/10S681J

RS1/10S222J

RS1/10S474J

401

402

403

610

611

Ferri-Inductor

Inductor

Ferri-Inductor

LAU4R7K

LAU2R2K

LAU100K

LAU101K

LAU2R2K

DEH-2130R,2100R

=====Circuit Symbol and No.===Part Name

--- ------ ------------------------------------------

Part No.

-------------------------

=====Circuit Symbol and No.===Part Name

--- ------ ------------------------------------------

Part No.

-------------------------

431

440

441

442

443

RS1/10S153J

RS1/10S681J

RS1/10S102J

RS1/10S473J

RS1/10S681J

911

912

914

916

918

RS1/10S122J

RD1/4PU103J

RD1/4PU152J

RS1/10S221J

RS1/10S1R0J

444

445

446

447

460

RS1/10S472J

RS1/8S473J

RS1/10S224J

RS1/10S0R0J

RS1/10S162J

941

942

951

953

954

RD1/4PU472J

RD1/4PU152J

RS1/10S153J

RS1/10S472J

RD1/4PU102J

461

464

465

474

475

RS1/10S162J

RS1/10S272J

RS1/10S222J

RS1/10S223J

955

981

982

983

984

RD1/4PU473J

RS1/10S472J

RS1/10S222J

RD1/4PU221J

476

477

478

479

611

RS1/10S223J

RS1/10S222J

RD1/4PU224J

RS1/10S224J

RS1/10S102J

CAPACITORS

310

311

312

313

314

CKSQYB105K16

CKSQYB104K16

CEJA2R2M50

CKSQYB105K16

CKSYB104K16

614

619

620

622

623

RS1/8S0R0J

RS1/10S0R0J

RN1/10SE2202D

RD1/4PU222J

315

316

317

318

319

CKSQYB102K50

CEJA100M16

CKSQYB822K50

624

625

626

627

628

RS1/10S473J

RD1/4PU473J

RD1/4PU222J

320

321

322

323

324

CKSQYB822K50

CEAL1R0M50

CEJA1R0M50

CKSQYB183K50

630

649

650

651

652

RS1/10S822J

RS1/8S222J

RS1/8S472J

325

326

327

328

329

CKSQYB104K16

CEJA2R2M50

653

654

655

656

657

RD1/4PU222J

RS1/10S473J

RS1/10S103J

RD1/4PU102J

330

332

333

334

335

CEJA4R7M50

CKSQYB473K16

CKSQYB104K16

CEAL470M10

658

660

681

682

683

RD1/4PU102J

RS1/10S1R0J

RD1/4PU681J

RS1/10S102J

RD1/4PU102J

340

341

350

361

362

CEAL2R2M50

CEJA2R2M50

CEJA330M10

CEJA2R2M50

CKSYB225K16

684

699

713

717

721

RS1/10S102J

RS1/10S0R0J

RS1/10S225J

RD1/4PU102J

RS1/10S102J

363

364

365

366

367

CEJA100M16

CKSYB474K16

CKSQYB474K16

CKSYB474K16

CKSQYB474K16

722

723

724

725

726

RS1/10S102J

RS1/10S681J

RS1/10S0R0J

368

369

370

371

372

CKSQYB474K16

CKSYB474K16

CKSQYB474K16

CKSYB474K16

CKSQYB225K10

727

901

902

903

904

RS1/8S0R0J

RS1/10S473J

RD1/4PU103J

RS1/10S473J

390

391

411

412

413

CKSQYB104K16

CCH1368

CKSQYB223K25

CKSQYB102K50

3300µF/16V

905

906

907

908

909

RS1/10S102J

RS1/10S473J

RS1/10S472J

RD1/4PU103J

414

415

416

417

418

CEJA220M10

CKSQYB473K16

CEAL101M10

CKSQYB472K50

DEH-2130R,2100R

=====Circuit Symbol and No.===Part Name

Part No.

-------------------------

=====Circuit Symbol and No.===Part Name

Part No.

-------------------------

--- ------

------------------------------------------

--- ------

------------------------------------------

441

442

462

463

466

CKSQYB182K50

CKSQYB223K25

CKSQYB123K25

CEJA1R0M50

203

901

902

904

905

Inductor

Coil

Inductor

LCTA121J3225

CTC1154

LCTA3R3J3225

LCTBR47K1608

467

490

493

612

613

CEJA1R0M50

Coil

CTE1132

CTF1442

CTF1348

CKSQYB103K50

CCSQCH100J50

CEJA4R7M35

Ceramic Filter

CKSQYB473K16

CF 202

614

621

630

631

650

CKSQYB102K50

CCSQCH101J50

CKSQYB473K16

CEAL2R2M50

901

Crystal Resonator 10.250MHz

CSS1432

RESISTORS

CKSQYB104K16

RS1/16S153J

RS1/16S103J

RS1/16S273J

RS1/16S473J

711

712

714

715

718

CEAL220M6R3

CKSQYB104K16

CKSQYB471K50

CKSQYB104K16

CKSQYB471K50

RS1/16S223J

RS1/16S473J

RS1/16S221J

RS1/16S103J

RS1/16S104J

719

720

725

726

901

CEAL220M6R3

CKSQYB104K16

CCSQCH270J50

CEJA101M10

RS1/16S223J

RS1/16S221J

RS1/16S473J

RS1/16S470J

902

903

904

905

906

CKSQYB473K16

CCH1331

470µF/16V

330µF/16V

CKSQYB473K16

CCH1326

CKSQYB103K50

RS1/16S470J

RS1/16S103J

RS1/16S331J

907

941

981

982

983

CEJA101M16

CKSQYB473K16

CEJA101M10

CKSQYB102K50

CKSQYB473K16

RS1/16S560J

RS1/16S102J

RS1/16S225J

RS1/16S133J

Unit Number : CWE1500

Unit Name

: FM/AM Tuner Unit

MISCELLANEOUS

101

102

103

RS1/16S433J

RS1/16S562J

RS1/16S333J

RS1/16S103J

RS1/16S333J

PML002A

PM4008A

BR9010FV

2SC4081

Transistor

DTC124EU

104

106

108

110

111

RS1/16S562J

RS1/16S0R0J

RS1/16S154J

RS1/16S273J

201

202

204

FET

3SK263

2SC4081

2SK932

DTC124EU

2SC4081

Transistor

FET

Transistor

112

113

114

115

116

RS1/16S223J

RS1/16S222J

RS1/16S333J

RS1/16S334J

RS1/16S473J

Diode

KV1410(23)

1SV248

KV1410(23)

1SS355

101

117

118

122

202

203

RS1/16S333J

RS1/16S223J

RS1/16S0R0J

RS1/16S472J

RS1/16S225J

201

202

903

904

Diode

Coil

DAN217U

KV1410(23)

SVC253

CTC1155

204

205

206

208

209

RS1/16S102J

RS1/16S220J

RS1/16S471J

RS1/16S104J

201

202

Coil

CTC1155

Inductor

Coil

LCTB100K2125

CTC1155

Inductor

LCTB330K1608

CTF1287

210

213

251

902

904

RS1/16S563J

RS1/16S223J

RS1/16S225J

RS1/16S103J

RS1/16S473J

DEH-2130R,2100R

=====Circuit Symbol and No.===Part Name

--- ------ ------------------------------------------

Part No.

-------------------------

=====Circuit Symbol and No.===Part Name

--- ------ ------------------------------------------

Part No.

-------------------------

907

908

909

914

RS1/16S103J

RS1/16S681J

RS1/16S473J

RS1/16S562J

208

209

210

211

212

CCSRCH560J50

CEAL470M6R3

CKSRYB103K50

CCSRCH101J50

CAPACITORS

215

216

217

219

220

CKSRYB223K25

CKSQYB334K16

CKSRYB103K50

CKSQYB105K10

CKSRYB104K16

CCSQCH5R0C50

CCSRCH5R0C50

CCSRCJ3R0C50

CKSQYB105K10

CKSRYB222K50

221

222

223

224

225

CKSRYB473K16

CKSQYB334K16

CKSQYB474K16

CKSRYB104K16

CKSRYB272K50

CCSRCH220J50

CCSRCH150J50

CCSRCH8R0D50

CCSRCJ3R0C50

CKSRYB103K50

226

902

904

905

906

CKSRYB682K25

CCSRCH270J50

CKSRYB223K25

CKSRYB103K50

CCSRTH100D50

CKSRYB222K50

CCSRCJ3R0C50

CKSRYB103K50

907

909

910

912

913

CCSRTH150J50

CCSRTH100D50

CKSRYB332K50

CKSQYB474K16

CKSRYB223K25

CKSRYB103K50

CKSQYB334K16

CKSRYB222K50

CCSRCH470J50

CKSRYB103K50

914

915

916

917

918

CKSRYB682K25

CKSQYB223K25

CKSQYB474K16

CKSYB475K10

CKSRYB223K25

CKSRYB103K50

CKSRYB473K16

CCSRCK2R0C50

CKSRYB103K50

CKSRYB104K16

919

920

921

922

923

CKSQYB225K10

CCSRCH270J50

CKSYB105K16

CKSRYB103K50

CKSRYB104K16

CKSQYB224K16

CKSRYB223K25

CKSRYB104K16

CEALNP100M10

101

Unit Number : CWM6779(DEH-2130R)

: CWM6778(DEH-2100R)

102

103

105

106

107

CCSRCH151J50

CKSRYB473K16

CKSRYB682K25

CEAL2R2M50

Unit Name

: Keyboard Unit

MISCELLANEOUS

CKSRYB103K50

IC 1801

PD6293A

MA152WK

MA152WA

CSS1422

CEL1638

108

109

110

111

112

CKSQYB474K16

CKSRYB104K16

1801

1802

1801

Diode

Ceramic Resonator 4.97MHz

Lamp 14V 40mA(DEH-2130R)

IL 1801

IL 1802

IL 1803

Lamp 14V 40mA(DEH-2100R)

Lamp 14V 40mA(DEH-2130R)

Lamp 14V 40mA(DEH-2100R)

Lamp 14V 40mA(DEH-2130R)

Lamp 14V 40mA(DEH-2100R)

CEL1547

CEL1638

CEL1547

CEL1638

CEL1547

113

114

115

116

117

CKSRYB123K25

CEAL220M6R3

CKSRYB473K16

CEAL2R2M50

CKSRYB102K50

IL 1804

LCD1801

Lamp 14V 40mA(DEH-2130R)

Lamp 14V 40mA(DEH-2100R)

LCD

CEL1638

CEL1547

CAW1559

120

121

122

123

125

CKSRYB153K25

CKSRYB332K50

CKSRYB682K25

CKSRYB681K50

CKSRYB103K50

RESISTORS

126

127

128

201

202

CKSRYB103K50

CEAL2R2M50

CKSRYB103K50

CCSRCH471J50

CCSRCH100D50

1801

1802

1803

1804

1805

RS1/8S222J

RS1/10S471J

203

204

205

206

207

CKSRYB104K16

CKSRYB332K50

CKSRYB103K50

CKSRYB104K16

CKSRYB473K16

1806

RS1/10S471J

CAPACITORS

1801

CKSQYB103K25

DEH-2130R,2100R

=====Circuit Symbol and No.===Part Name

--- ------ ------------------------------------------

Part No.

-------------------------

=====Circuit Symbol and No.===Part Name

Part No.

-------------------------

--- ------

------------------------------------------

220

221

222

223

224

CCSRCH510J50

CKSRYB682K25

CEV220M6R3

CKSRYB103K25

CKSRYB224K10

Unit Number : CWX2411

Unit Name

: Control Unit

MISCELLANEOUS

201

301

701

101

801

UPD63711GC

BA5985FM

BA05SFP

301

603

604

702

703

CEV101M10

CCSQSL152J50

CCH1349

Transistor

LED

2SB1132

10µF/10V

CL200IRX

CKSQYB334K16

802

201

801

802

LED

CL200IRX

CSS1456

CSN1051

CSN1052

Unit Number :

Ceramic Oscillator 16.934MHz

Spring Switch(HOME)

Unit Name

: Photo Unit(S8)

Spring Switch(CLAMP)

Photo-transistor

CPT230SX-TU

RESISTORS

Miscellaneous Parts List

101

102

103

201

202

RS1/8S120J

RS1/8S100J

RS1/16S222J

RS1/16S104J

RS1/16S103J

Pickup Unit(Service)(P8)

CXX1285

CXB2190

CXB2195

CXB2562

CEK1136

Motor Unit(CARRIAGE)

Motor Unit(LOADING)

Motor Unit(SPINDLE)

Fuse(10A)

203

204

205

206

207

RS1/16S393J

RS1/16S103J

RS1/16S182J

RS1/16S123J

302

303

501

502

601

RS1/16S153J

RS1/16S103J

RS1/16S102J

RA4C681J

RS1/16S102J

602

605

606

801

803

RS1/16S102J

RS1/16S0R0J

RS1/8S751J

902

906

RS1/16S0R0J

CAPACITORS

101

102

103

104

105

CCSRCH102J25

CKSRYB104K16

CEV101M6R3

CEV470M6R3

CKSQYB334K16

106

107

201

202

203

CKSQYB334K16

CKSRYB104K16

CKSRYB471K50

CKSRYB104K16

205

206

207

208

209

CEV101M6R3

CKSRYB104K16

210

211

212

213

214

CKSRYB332K50

CKSRYB104K16

CKSRYB392K50

CKSRYB104K16

215

216

217

218

219

CKSRYB104K16

CCSRCJ3R0C50

CCSRCH270J50

CKSRYB104K16

CCSRCH181J50

DEH-2130R,2100R

6. ADJUSTMENT

6.1 CD ADJUSTMENT

1) Precautions

2) Test Mode

• This unit uses a single power supply (+5V) for the reg-

ulator. The signal reference potential, therefore, is

connected to REFO(approx. 2.5V) instead of GND.

If REFO and GND are connected to each other by mis-

take during adjustments, not only will it be impossi-

ble to measure the potential correctly, but the servo

will malfunction and a severe shock will be applied to

the pick-up. To avoid this, take special note of the fol-

lowing.

This mode is used for adjusting the CD mechanism

module of the device.

• Test mode starting procedure

Reset while pressing the 4 and 6 keys together.

• Test mode cancellation

Switch ACC, back-up OFF.

Do not connect the negative probe of the measuring

equipment to REFO and GND together. It is especially

important not to connect the channel 1 negative

probe of the oscilloscope to REFO with the channel 2

negative probe connected to GND.

Since the frame of the measuring instrument is usual-

ly at the same potential as the negative probe, change

the frame of the measuring instrument to floating sta-

tus.

• After pressing the EJECT key, do not press any other

key until the disk is completely ejected.

• If the ] or [ key is pressed while focus search is in

progress, immediately turn the power off (otherwise

the actuator may be damaged due to adhesion of the

lenses).

• Jump operation of TRs other than 100TR continues

after releasing the key. CRG move and 100TR jump

operations are brought into the “Tracking close” sta-

tus when the key is released.

If by accident REFO comes in contact with GND,

immediately switch the regulator or power OFF.

• Always make sure the regulator is OFF when connect-

ing and disconnecting the various filters and wiring

required for measurements.

• Powering Off/On resets the jump mode to “1TR”, and

the automatic adjustment value to the initial value.

• Before proceeding to further adjustments and mea-

surements after switching regulator ON, let the player

run for about one minute to allow the circuits to stabi-

lize.

• Since the protective systems in the unit's software are

rendered inoperative in test mode, be very careful to

avoid mechanical and /or electrical shocks to the sys-

tem when making adjustment.

• Disc detection during loading and eject operations is

performed by means of a photo transistor in this

unit.Consequently, if the inside of the unit is exposed

to a strong light source when the outer casing is

removed for repairs or adjustment, the following mal-

functions may occur.

*During PLAY, even if the eject button is

pressed,the disc will not be ejected and the unit

will remain in the PLAY mode.

*The unit will not load a disc.

When the unit malfunctions this way, either re-posi-

tion the light source, move the unit or cover the photo

transistor.

DEH-2130R,2100R

- Flow Chart

Test Mode In

SOURCE

Reset

Select CD

New test mode

BAND

Power ON

(Adjustment for T.Offset)

Power ON

(Not adjustment for T.Offset)

TRK

00 ^MI0^N0 ^SE0^C0

TRK

99 ^MI9^N9 ^SE9^C9

Display

Power OFF

BAND

]

[

Focus Close/

S Curve Check

Focus Mode

Select

Auto Adjustment

Display Select

CRG+

CRG-

TRK

91 ^MI9^N1 ^SE9^C1

00 ^MI0^N0 ^SE0^C0

TRK

0x^MI0^Nx ^SE0^Cx

Display

99 ^MI9^N9 ^SE9^C9

TRK

Power OFF

]

[

BAND

T.Close and

F,T AGC and

RF AGC and

Fit Servo

T. Close and

Fit Servo

T.Balance

Adjustment

RF AGC Coefficient Display/

Rough Servo and RF AGC

CRG+

CRG-

8x ^MI8^Nx ^SE8^Cx

TRK

8x ^MI8^Nx ^SE8^Cx

Display

9x ^MI9^Nx ^SE9^Cx

TRK

9x ^MI9^Nx ^SE9^Cx

Tracking

Open

Power OFF

BAND

]

[

CRG-/TR Jump-

F, T, RF AGC/

F.Bias Display Select

F, T AGC and

RF AGC

CRG/TR Jump NO.

Select

CRG+/TR Jump+

TRK

8x ^MI8^Nx ^SE8^Cx

Power OFF

BAND

Display

9x ^MI9^Nx ^SE9^Cx

TRK

Tracking

Open

TRK

8x ^MI8^Nx ^SE8^Cx

Display

9x ^MI9^Nx ^SE9^Cx

TRK

*1 "00", "99"→Focus Close / "01"→S.Curve

*6 1TR/4TR/10TR/32TR/100TR

S.Curve

LD Off

CRG Move,100TR Jump

Focus Close

00(99)

The original display

T.Offset

F.Cancel

T.AGC Gain

TRK, MIN, SEC

F.Bias

F.AGC Gain

4TR

92(82)

10TR

93(83)

32TR

94(84)

100TR

95(85)

CRG Move

96(86)

1TR

91(81)

DEH-2130R,2100R

6.2 CHECKING THE GRATING AFTER CHANGING THE PICKUP UNIT

• Note :

The grating angle of the PU unit cannot be adjusted after the PU unit is changed. The PU unit in the CD mecha-

nism module is adjusted on the production line to match the CD mechanism module and is thus the best adjusted

PU unit for the CD mechanism module. Changing the PU unit is thus best considered as a last resort. However, if

the PU unit must be changed, the grating should be checked using the procedure below.

• Purpose :

To check that the grating is within an acceptable range when the PU unit is changed.

• Symptoms of Mal-adjustment :

If the grating is off by a large amount symptoms such as being unable to close tracking, being unable to perform

track search operations, or taking a long time for track searching.

• Method :

• Measuring Equipment

• Measuring Points

• Disc

• Oscilloscope, Two L.P.F.

• E, F, REFOUT

• ABEX TCD-784

• TEST MODE

• Mode

CONTROL UNIT

L.P.F.

Xch

Ych

100kΩ

390pF

Oscilloscope

REFO

100kΩ

390pF

REFO

L.P.F.

• Checking Procedure

1. In test mode, load the disc and switch the 5V regulator on.

2. Using the ] and [ buttons, move the PU unit to the innermost track.

3. Press key 3 to close focus, the display should read "91". Press key 2 to implement the tracking balance adjust-

ment the display should now read "81". Press key 3 2 times. The display will change, returning to "81" on the

fourth press.

4. As shown in the diagram above, monitor the LPF outputs using the oscilloscope and check that the phase differ-

ence is within 75° . Refer to the photographs supplied to determine the phase angle.

5. If the phase difference is determined to be greater than 75° try changing the PU unit to see if there is any

improvement. If, after trying this a number of times, the grating angle does not become less than 75° then the

mechanism should be judged to be at fault.

• Note

Because of eccentricity in the disc and a slight misalignment of the clamping center the grating waveform may be

seen to "wobble" ( the phase difference changes as the disc rotates). The angle specified above indicates the aver-

age angle.

• Hint

Reloading the disc changes the clamp position and may decrease the "wobble".

DEH-2130R,2100R

Ech → Xch 20mV/div, AC

Grating waveform

Fch → Ych 20mV/div, AC

0°

30°

60°

90°

45°

75°

DEH-2130R,2100R

7. GENERAL INFORMATION

7.1 DIAGNOSIS

7.1.1 TEST MODE

- Error Messages

If a CD is not operative or stopped during operation due to an error, the error mode is turned on and cause(s) of the

error is indicated with a corresponding number. This arrangement is intended at reducing nonsense calls from the

users and also for facilitating trouble analysis and repair work in servicing.

(1) Basic Indication Method

1) When SERRORM is selected for the CSMOD (CD mode area for the system), error codes are written to DMIN (min-

utes display area) and DSEC (seconds display area). The same data is written to DMIN and DSEC. DTNO remains

in blank as before.

2) Head unit display examples

Depending on display capability of LCD used, display will vary as shown below. xx contains the error number.

8-digit display

6-digit display

ERR–xx

4-digit display

ERROR–xx

E–xx

Err–xx

(2) Error Code List

Code Class

Displayed error code Description of the code and potential cause(s)

Electricity Carriage Home NG CRG can't be moved to inner diameter.

CRG can't be moved from inner diameter.

→ Failure on home switch or CRG move mechanism.

Electricity Focus Servo NG

Focusing not available.

→ Stains on rear side of disc or excessive vibrations on REWRITABLE.

Spindle not locked. Sub-code is strange (not readable).

→ Failure on spindle, stains or damages on disc, or excessive vibrations.

A disc not containing CD-R data is found. Turned over disc are found,

though rarely.

Electricity Spindle Lock NG

Subcode NG

→ Failure on home switch or CRG move mechanism.

An appropriate RF AMP gain can't be determined.

→ CD signal error.

APC protection doesn't work. Focus can be easily lost.

→ Damages or stains on disc, or excessive vibrations.

Failed to reach target address.

RF AMP NG

Electricity Setup NG

Electricity Search Time Out

→ CRG tracking error or damages on disc.

Power (VD) is ground faulted.

System

Power Supply NG

→ Failure on SW transistor or power supply (failure on connector).

Remarks: Mechanical errors are not displayed (because a CD is turned off in these errors).

Unreadable TOC does not constitute an error. An intended operation continues in this case.

A newly designed head unit must conform to the example given above.

Upper digits of an error code are subdivided as shown below:

1x: Setup relevant errors, 3x: Search relevant errors, 3x: Search relevant errors, Ax: Other errors.

DEH-2130R,2100R

- New Test Mode

S-CD plays the same way as before.

If an error such as off focus, spindle unlocking, unreadable sub-code, or sound skipping occurs after setup, its

cause and time occurred (in absolute time) are displayed.

During setup, operational status of the control software (internal RAM: CPOINT) is displayed.

These displays and functions are prepared for enhancing aging in the servicing and efficiency of trouble analysis.

(1) Shifting to the New Test Mode

1 Turn on the current test mode by starting the reset from the key.

2 Select S-CD for the source through the specified procedure including use of the [SOURCE] key, and inserting the

disc. Then, press the [Jump Mode Selector] key while maintaining the regulator turned off.

3 After the above operations, the new test mode remains on irrespective of whether the S-CD is turned on or off.

You can reset the new test mode by turning on the reset start.

* With some products, the new test mode can be reset through the same operations as that employed for shifting to

the STBY mode (while maintaining the Acc turned off).

(2) Key Correspondence

Key

Test mode

New test mode

In-play Error Production

(Example)

Power Off

Power On

To power off

BAND To power on

(offset adjustment performed)

–

Time/Err.No. switching

]

[

–

FWD-Kick

FF/TR+

REV/TR-

Scan

–

REV-Kick

T.Close (AGC performed)

/parameter display switching

T.BAL adjustment

/T.Open

–

Mode

–

To power on

F.Close/RF AGC/AGC

–

(offset adjustment not performed)

–

Mode switching

Auto/Manu –

/T.Close (no AGC)/Jump switching

Note: Eject and CD on/off is performed in the same procedure as that for the normal mode.

(3) Cause of Error and Error Code

Code Class

Contents

Description and cause

Electricity Off focus detected.

FOK goes low.

→ Damages/stains on disc, vibrations or failure on servo.

FOK = Low continued for 50 msec.

Electricity Spindle unlocked.

→ Damages/stains on disc, vibrations or failure on servo.

Sub-code was unreadable for 50 msec.

→ Damages/stains on disc, vibrations or failure on servo.

Last address memory function was activated.

→ Damages/stains on disc, vibrations or failure on servo.

Electricity Sub-code unreadable.

Electricity Sound skipping detected.

Note: Mechanical errors during aging are not displayed.

The error codes should be indicated in the same way as in the normal mode.

DEH-2130R,2100R

(4) Display of Operational Status (CPOINT) during Setup

Status No. Contents

Protective action

None

Specified 10 seconds has been passed or failure

on home switch.

Carriage move to home position started.

Carriage is moving toward inner diameter.

Carriage is moving toward outer diameter.

Specified 10 seconds has been passed or failure

on home switch.

Carriage outer diameter feed (1 second) in progress. None

Setup started.

None

Spindle rotation and focus search started.

Waiting for focus close (XSI=Low).

Waiting for focus close (FOK=High). (After AGC)

Waiting for focus close (FOK=High). (Before AGC)

Rough AGC in progress.

Setup (1/2) before T balance adjustment is started.

Setup (2/2) before T balance adjustment is started.

T balance adjustment (1/2).

None

Specified focus search time has been passed.

Off focus.

T balance adjustment (2/2).

Standing by after spindle rough servo is over.

Setup before RF AGC (first) is started.

RF AGC (first) in progress.

Setup before RF AGC (second) is started.

RF AGC (second) in progress.

Tracking close in progress.

Standing by after tracking is closed.

Focus AGC started.

Focus AGC in progress. Tracking AGC started.

Tracking AGC in progress.

Spindle processes applicable servo.

Check of MIRR and LOCK pin. RF AGC in progress.

CRG close in progress. Check of sub-code.

Off focus. Spindle not locked.

Sub-code unreadable.

(5) Display Examples

1) During Setup (When status no. = 11)

TRK No.

MIN.

11'

SEC.

11"

2) During Operation (TOC read, TRK search, Play, FF and REV)

The same as in the normal mode.

3) When a Protection Error Occurred

Switch to the following displays (A) and (B) using the [BAND] switch:

(A) Error occurrence timing display in absolute time.

An example: Error occurred in 12th tune at 34'56" in absolute time.

TRK No.

MIN.

34'

SEC.

56"

(B) Error No. display

An example: Error #40 (Off focus is detected)

ERROR-40

DEH-2130R,2100R

7.1.2 DISASSEMBLY

- Removing the Upper Case (not shown)

- Removing the CD Mechanism Module (Fig.1)

Remove the four screws.

Disconnect the connector and then remove the CD

Mechanism Module (not shown).

- Removing the Panel Assy (not shown)

1.Disconnect the two stoppers and then remove the

Panel Assy.

Fig.1

CD Mechanism Module

Cover

- Removing the Tuner Amp Assy

Remove the two screws (Fig.2).

Remove the three screws and then remove

the Cover (Fig.2).

Fig.2

Remove the screw (Fig.3).

Disconnect the four claws and then remove

the Tuner Amp Assy (Fig.3).

Fig.3

Tuner Amp Assy

DEH-2130R,2100R

- Removing the Upper Frame

1. Remove six Springs A, two Springs B and four

Screws.

Upper Frame

2. Remove two Tabs situated on rear side of the Upper

Frame, remove two Arms on the front side, then

remove two Tabs on the front side.

Arm

- Removing the Carriage Mechanism

1. Disengage the Carriage Mechanism from the two

dampers situated in the front side by driving it up,

then disengage and remove the mechanism from the

one damper by driving it up aslant into front side

direction.

Carriage Mechanism Section

Note : When assembling the Carriage Mechanism, coat

the dampers with alcohol prior to the assembly.

- Removing the Clamp Arm Assy

Clamp Arm Assy Section

1. Remove a Spring A, a B and a Spring C.

2. Drive the Clamp Arm Assy up into rear side direction,

then disengage the arm from its current position

Finally, drive the assembly approximately 45 degrees

upward, then slide the assembly toward right side to

remove it.

DEH-2130R,2100R

- Removing the Guide Arm Assy

1. Remove a connector, a spring A and B

Guide Arm Assy Section

2. Drive the Guide Arm Assy up aslant into rear side

direction, then remove it from a Pin. Finally, drive the

assembly approximately 45 degrees upward, then

slide the assembly toward left side to remove it.

Note : When assembling the guide arm assembly, route

the cord inside the assembly. In this operation,

care must be exercised so that cord may be

caught by the gear.

LO Arm Assy Section

- Removing the LO Arm Assy

1. Remove two Pins to dismount the LO Arm Assy.

- Removing the Control Unit and the Spindle

Short Pin

Motor

1. Remove from the connector after mounting the short

pin on the flexible PCB of the pickup unit.

2. Remove two Soldered joints, then remove two

Screws A.

Spindle Motor

3. Remove two connectors and a Screw B.

4. Disengage the Control Unit from two Tabs, then dis-

mount the unit by sliding it toward left.

5. Dismount the Spindle Motor.

Control Unit

DEH-2130R,2100R

- Removing the Loading Motor and Carriage

Motor

Guide

1. Remove the Spring and two Screws A.

2. Dismount the Loading Motor.

3. Remove the Belt, a Screw B, two Screws C, a Guide

and a Screw Unit.

Screw Unit

Carriage Motor

4. Dismount the Carriage Motor.

Note : When assembling the Belt, use care so that it

may not be contaminated by grease.

Belt

Loading Motor

- Removing the Pickup Unit

1. Remove two Screws and a Shaft.

2. Dismount the Pickup Unit.

Pickup Unit

Shaft

DEH-2130R,2100R

7.2 PARTS

7.2.1 IC

- Pin Functions(PE5090A)

Pin No.

Pin Name

MODEL1

NL1

I/O

Format

Function and Operation

Model select input

Noise level input

Noise level input 2

A/D GND

NL2DT

AVSS

Stereo input

SD signal input

AREF1

KYDT

(D/A converter standard voltage)

Key data input

DPDT

Key data output

SDBW input

PLL IC data input

PLL IC data output

36–39

54–57

SDBW

TUNPDI

TUNPDO

TUNPCK

TUNPCE

CURRQ

XSI

XSO

XSCK

DRST

ADPW

FM/AM

VDCONT

CONT

XAO

PLL IC clock output

PLL IC chip enable output

Tuner voltage FIX output

LSI data input

LSI data output

LSI clock output

RDS decoder reset output

A/D converter power output

FM/AM power select output

VD power control output

Servo driver power control output

CD LSI data discernment control signal output

CD LSI reset output

CD LSI strobe output

Disc clamp sense input

Mirror detection input

Focus OK signal input

Spindle lock detector input

LOAD motor loading control output

Cellular mute input

XRST

XSTB

CLAMP

MIRR

FOK

LOCK

CDLOAD

TELIN

VSS

CDEJECT

CD5VON

RECIEVE

SWVDD

SYSPW

MUTE

PEE

LOCH

RDS57K

TUNPCE2

VCK

VDT

GND

LOAD motor eject control output

CD +5V power supply control output

Not used

RDS decoder receiving output

Grille power supply control output

System power supply control output

Not used

Mute output

Beep tone output

LOCH output

57kHzBP-OUT sense input

EEPROM chip enable output 2

Not used

Clock output for electronic volume

Data output for electronic volume

Antenna power output

Strobe pulse output for electronic volume

Direct EQ data output 4-1

RDS LK signal input

ANTPW

VST

DEQ4-1

RDSLK

RDT

RDS data input

Reset

RESET

DEH-2130R,2100R

Pin No.

Pin Name

LDET

RCK

ASENS

BSENS

DSENS

TMUTE

LOCL

VDD

TESTIN

AVDD

AVREF0

TEMP

VDSENS

DSCSNS

EJTSNS

I/O

Format

Function and Operation

PLL lock sense input

RDS clock input

ACC power sense input

Back up power sense input

Grille detach sense input

Tuner mute output

LOC L output

Power supply

Crystal oscillator connection pin

GND

Not used

Test program mode input

Positive power supply terminal for analog circuit

GND

Signal level input

Temperature detector input

Over voltage sense input

Disc detect input

Disc EJECT position detect input

IC's marked by* are MOS type.

Be careful in handing them because they are very liable

to be damaged by electrostatic induction.

Output Format

Meaning

C MOS output

*PE5090A

S-80834ANY

OUT

VDD

VSS

DEH-2130R,2100R

SN761029DL

48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25

Isolator

Volume,

Loudness

Treble

Bass

Fader

Gain

Adjust

Zero-cross

Detector

Power

Supply

3 Line Serial Bus

Gain

Adjust

Volume,

Loudness

Power

Supply

Fader

Bass

Treble

Isolator

10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

PM4009A

DEH-2130R,2100R

BR9010FV

VCC

GND

CS : Chip select input

SK : Serial data clock input

DI : Serial data input

DO: Serial data output

WC: Write control input

- Pin Functions (PD6293A)

Pin No.

1-5

Pin Name

SEG4-0

COM3-0

VLCD

KST3-0

KDT0,1

REM

I/O

Function and Operation

LCD segment output

LCD common output

LCD drive power supply

Key strobe output

Key data input (analogue input)

Remote control reception

Display data input

Not used

6-9

11-14

15,16

DPDT

KYDT

MODA

VSS

Key data output

GND

Crystal oscillator connection pin

GND

25,26

KDT2,3

Key data input

Not used

KST4

SEG35-13

VDD

Key strobe output

Not used

LCD segment output

Power supply

29-32

33-55

57-64

SEG12-5

LCD segment output

*PD6293A

DEH-2130R,2100R

- Pin Functions (UPD63711GC)

Pin No.

Pin Name

D.GND

RFOK

rst

I/O

Function and Operation

Logic circuit GND

RFOK signal output

Reset signal input

stb

Command/parameter identification signal input

Data strobe signal input

sck

Clock signal input for serial data input/output

Serial data and status signal output

Serial data input

xtalen

D.VDD

DA.VDD

R_OUT

DA.GND

REGC

DA.GND

L_OUT

DA.VDD

R+

R-

L-

L+

X.VDD

XTAL

xtal

X.GND

D.VDD

EMPH

FLAG

Crystal oscillation control pin

Positive power supply terminal to logic circuit

Positive power supply terminal to D/A converter

Right channel audio output signal

D/A converter GND

The outside putting capacitor connection pin for SCF regulator

D/A converter GND

Left channel audio output signal

Positive power supply terminal to D/A converter

Right channel audio data output

Left channel audio data output

Positive power supply terminal to crystal oscillation circuit

Crystal oscillator connect pin

Crystal oscillation circuit GND

Positive power supply terminal to logic circuit

Output pin for the pre-emphasis data in the sub-Q code

Flag output pin to indicate that audio data currently being output consists

of noncorrectable data

DIN

Serial data input to internal DAC

Serial audio data output

DOUT

SCKIN

SCKO

LRCKIN

LRCK

Serial clock input to internal DAC

Audio data that is output from DOUT changes at rising edge of this clock

LRCK signal input to internal DAC

Signals to distinguish the right and left channels of the audio data output

from DOUT

HOLD

Defect detection output

Digital audio interface data output

Logic circuit GND

D.GND

C16M

LIMIT

D.VDD

LOCK

RFCK

MIRR

PLCK

D.GND

C1D1

C1D2

C2D1

C2D2

C2D3

D.VDD

PACK

TSO

Oscillator clock buffering output

Status of the pin is output at Bit 5 of the status output

Positive power supply terminal to logic circuit

EFM synchronous detection signal

Frame synchronous signal of XTAL-system

MIRR output

Monitor pin of bit clock

Logic circuit GND

Output pin for indicating the C1 error correction results

Output pin for indicating the C2 error correction results

Positive power supply terminal to logic circuit

CD-TEXT PACK synchronous signal

CD-TEXT data serial output

CD-TEXT control parameter serial input

CD-TEXT serial clock input

CD-TEXT parameter strobe signal input

Logic circuit GND

TSI

tsck

TSTB

D.GND

DEH-2130R,2100R

Pin No.

100

Pin Name

TEST0

TEST1

ATEST

A.GND

DAC0

DAC1

DAC2

DAC3

A.VDD

EFM

ASY

C3T

I/O

Function and Operation

Test pin

Analog circuit GND

Focus drive output

Tracking drive output

Sled drive output

Spindle drive output

DAC output for adjustment

Positive power supply terminal to analog circuit

EFM signal output

EFM comparator reference voltage input

3T detection capacitor additional pin

RF signal input for EFM data regulation

RF signal output of after gain adjustment

RF-AGC amplifier input

RF summing amplifier output

RF amplifier equalizer parts additional pin

RF summing amplifier inverted input

Analog circuit GND

Photo detector A input

Photo detector C input

Photo detector B input

Photo detector D input

Photo detector F input

Photo detector E input

Positive power supply terminal to analog circuit

Reference electric potential output

Focus error amplifier inverted input

Focus error amplifier output

Tracking error amplifier inverted input

Tracking error amplifier output

Tracking error output of after amplification

Tracking comparator input

Analog circuit GND

PD detection signal input for LD output monitor

LD control current output

APC circuit control polarity set pin

Positive power supply terminal to analog circuit

RFI

AGCO

AGCI

RFO

EQ2

EQ1

RF-

A.GND

A.VDD

REFOUT

FE-

FEO

TE-

TEO

TE2

TEC

A.GND

A.VDD

*UPD63711GC

100

DEH-2130R,2100R

- Pin Functions (BA5985FM)

Pin No.

Pin Name

FWD

I/O

Function and Operation

Loading driver FWD input

CH1 pre-amplifier input

CH1 pre-amplifier inverted input

CH1 pre-amplifier output

CH2 pre-amplifier input

CH2 pre-amplifier inverted input

CH2 pre-amplifier output

Power supply

OPIN1(+)

OPIN1(−)

OPOUT1

OPIN2(+)

OPIN2(−)

OPOUT2

VCC

VOL(−)

VOL(+)

VO2(−)

VO2(+)

VO1(−)

VO1(+)

VO4(+)

VO4(−)

VO3(+)

VO3(−)

GND

Loading driver negative output

Loading driver positive output

Driver CH2 negative output

Driver CH2 positive output

Driver CH1 negative output

Driver CH1 positive output

Driver CH4 positive output

Driver CH4 negative output

Driver CH3 positive output

Driver CH3 negative output

GND

BIAS

MUTE

Bias input

Mute control

OPOUT3

OPIN3(−)

OPIN3(+)

OPOUT4

OPIN4(−)

OPIN4(+)

REV

CH3 pre-amplifier output

CH3 pre-amplifier inverted input

CH3 pre-amplifier input

CH4 pre-amplifier output

CH4 pre-amplifier inverted input

CH4 pre-amplifier input

Loading driver REV input

BA5985FM

DEH-2130R,2100R

7.2.2 DISPLAY

- CAW1559

DEH-2130R,2100R

7.3 OPERATIONAL FLOW CHART

Power ON

VDD=5V

68pin

bsens

66pin

asens

65pin

dsens

63pin

ADPW←H

20pin

Starts communication with Grille microcomputer.

300ms

swvdd←L

41pin

300ms

In case of the above signal, the communication

with Grille microcomputer may fail.

If the time interval is not 300msec, the oscillator

may be defective.

Source keys

operative

Source ON

YES

SYSPW←H

42pin

To each source's flow chart

DEH-2130R,2100R

8. OPERATIONS AND SPECIFICATIONS

8.1 OPERATIONS

SOURCE/OFF button

BAND button

5/∞/2/3 buttons

EJECT button

+/– button

Disc Loading Slot

TA/AF button

PTY button

LOCAL/BSM button

Detach button

DISP button

AUDIO button

Buttons 1–6

DEH-2130R,2100R

8.2 SPECIFICATIONS

General

FM tuner

Power source .......... 14.4 V DC (10.8 – 15.1 V allowable)

Grounding system ........................................ Negative type

Max. current consumption ...................................... 10.0 A

Dimensions

Frequency range ...................................... 87.5 – 108 MHz

Usable sensitivity

.................. 11 dBf (1.0 µV/75 Ω, mono, S/N: 30 dB)

50 dB quieting sensitivity .... 16 dBf (1.7 µV/75 Ω, mono)

Signal-to-noise ratio ...................... 70 dB (IEC-A network)

Distortion .......................... 0.3% (at 65 dBf, 1 kHz, stereo)

Frequency response ...................... 30 – 15,000 Hz (±3 dB)

Stereo separation .......................... 40 dB (at 65 dBf, 1 kHz)

(mounting size) ...... 178 (W) × 50 (H) × 159 (D) mm

(front face) .............. 188 (W) × 58 (H) × 19 (D) mm

Weight ...................................................................... 1.4 kg

Amplifier

MW tuner

Maximum power output ...................................... 40 W × 4

Continuous power output .................................... 22 W × 4

(DIN45324, +B = 14.4 V)

Frequency range ........................ 531 – 1,602 kHz (9 kHz)

Usable sensitivity .............................. 18 µV (S/N: 20 dB)

Selectivity .................................................. 50 dB (±9 kHz)

Load impedance .......................... 4 Ω (4 – 8 Ω allowable)

Preout maximum output level/output impedance

................................................................ 2.2 V /1 kΩ

Tone controls

(Bass) .............................................. ±12 dB (100 Hz)

(Treble) ............................................ ±12 dB (10 kHz)

Loudness contour.......... +10 dB (100 Hz), +7 dB (10 kHz)

(volume: –30 dB)

LW tuner

Frequency range ........................................ 153 – 281 kHz

Usable sensitivity .............................. 30 µV (S/N: 20 dB)

Selectivity .................................................. 50 dB (±9 kHz)

CD player

System .................................... Compact disc audio system

Usable discs .................................................. Compact disc

Signal format...................... Sampling frequency: 44.1 kHz

Number of quantization bits: 16; linear

Frequency characteristics................ 5 – 20,000 Hz (±1 dB)

Signal-to-noise ratio ........ 94 dB (1 kHz) (IEC-A network)

Dynamic range ............................................ 92 dB (1 kHz)

Number of channels ............................................ 2 (stereo)

Note:

•

Specifications and the design are subject to possi-

ble modification without notice due to improve-

ments.

Raypak XFYRE 700 User Manual
Pyramid Car Audio PB781X User Manual
Planar Systems Car Video System PT1745S User Manual
Pelco Camera Lens 12FA45C User Manual
Panasonic SDR S10PC User Manual
Olympus FE 290 User Manual
Metz NB 1010 User Manual
Manfrotto MBAG70 User Manual
KitchenAid KFP750ER2 User Manual
Kenwood KFCX1300P User Manual