Philips CMQ205 User Manual

Rwegwistewr yo.upr hproildiupctsan.dcgoetmsup/pworteatlcome  
CMQ205  
EN  
ES  
User manual  
3
13  
25  
Manual del usuario  
PT-BR Manual do Usuário  
RU  
ZH-CN
߀
൱Ҭꢀ  
Руководство пользователя 37  
49  
1 Important  
Notice  
Environmental information  
All unnecessary packaging has been omitted.  
We have tried to make the packaging easy to  
separate into three materials: cardboard (box),  
polystyrene foam (buffer) and polyethylene  
(bags, protective foam sheet.)  
Your system consists of materials which can  
be recycled and reused if disassembled by  
a specialized company. Please observe the  
local regulations regarding the disposal of  
packaging materials, exhausted batteries and  
old equipment.  
Safety  
Read and understand all instructions  
before you use the apparatus. If damage  
is caused by failure to follow instructions,  
the warranty does not apply.  
This unit is designed for negative ground  
(earth) 12 V DC operation only.  
Use only the supplied mounting hardware  
for a safe and secure installation.  
Do not connect any active speakers (with  
built-in amplifier) to the speaker terminals  
of the unit. Doing so may damage the  
active speakers.  
Any changes or modifications made to this  
device that are not expressly approved by  
Philips Consumer Lifestyle may void the user’s  
authority to operate the equipment.  
To ensure safe driving, adjust the volume  
to a safe and comfortable level.  
To avoid short circuit, do not expose the  
apparatus, remote control or remote  
control batteries to rain or water.  
Never expose the apparatus to direct  
sunlight, naked flames or heat.  
Clean the apparatus with soft, damp  
cloth. Never use substances such as  
alcohol, chemicals or household cleaners  
on the apparatus.  
2010 © Koninklijke Philips Electronics N.V. All  
rights reserved.  
Specifications are subject to change without  
notice. Trademarks are the property of  
Koninklijke Philips Electronics N.V. or their  
respective owners. Philips reserves the right  
to change products at any time without being  
obliged to adjust earlier supplies accordingly.  
4
EN  
2 Your car power  
amplifier  
Overview of the main unit  
Congratulations on your purchase, and  
welcome to Philips!To fully benefit from the  
support that Philips offers, register your product  
(
)
30A  
Introduction  
With the amplifier, you can enjoy high quality  
sound performance with powerful bass and  
beats.  
a INPUT L/R  
Connect car audio with RCA cable.  
What’s in the box  
Check and identify the contents of your  
package:  
b OUTPUT L/R  
To connect additional amplifier with  
RCA cable for additional speakers.  
c INPUT LEVEL  
Adjust input level (0.3V to 6V).  
d FILTER MODE  
Set frequency filter at LPF (low-pass-  
filter), HPF (high-pass-filter), or OFF  
(flat) mode.  
e LPF FREQUENCY  
Set LPF (low-pass-filter) frequency  
from 80Hz to 120Hz.  
a Amplifier  
f BASS BOOST  
Boost frequency for around 50Hz,  
12dB.  
b Screw (25mm) x 4  
c Fuse x 1  
g POWER/PROTECTED  
Light in green when the amplifier is  
switched on.  
Light in red when the amplifier is  
abnormal and protected.  
h SPEAKER OUTPUT  
Connect to speakers or subwoofers.  
EN  
5
i FUSE: 30AX1  
3 Installation  
j POWER  
To connect +12V-DC power wire,  
ground wire, and remote control  
wire.  
Note  
Follow all mounting and wiring instructions.  
Mount the amplifier in car  
You can mount the amplifier either under a seat  
or on the rear tray.  
Note  
To avoid interference, do not place the  
amplifier too close to the car audio or antenna.  
The supplied mounting screws are 25mm long.  
Make sure that the mounting board is thicker  
than 25mm.  
1 Place the unit on the location for  
installation.  
2 Mark the positions of the four screw  
holes.  
3 Drill the holes with driller of  
approximately 4mm in diameter.  
4 Mount the unit with the supplied screws.  
6
EN  
Connect speakers  
Connect car audio  
Option 1: Line input connection  
Connect the amplifier to the car audio with an  
RCA cable (not supplied).  
Note  
Use speakers with an impedance of 2 to 8 ohm  
(4 to 8 ohm when used as a bridged amplifier).  
Match the “left”, “right”, “+” and “-” terminals  
correctly. Revised polarity may degrade sound  
quality.  
Car audio unit  
LINE OUT  
Option 1: Stereo mode: connect 2 speakers  
(30A)  
Option 2: Line output connection  
Connect the amplifier to another amplifier.  
4 ohm  
4 ohm  
speaker  
speaker  
Option 2: Mono bridged mode: connect  
1 speaker  
(30A)  
Connect power  
1 Make the power connection as illustrated  
4 ohm  
speaker  
below:  
Connect the ground wire from the  
Option 3:Tri-mode: connect 3 speakers  
car to the GND socket.  
Connect the remote wire from the  
car audio to the REM socket.  
With this connection, you can turn  
on/off the amplifier with the car  
audio.  
Connect the power wire from the  
car battery to the +12V socket.  
(30A)  
4 ohm 4 ohm  
speaker speaker  
8 ohm speaker  
EN  
7
(30A)  
To a metal point of the car  
Less than 450mm (18 in)  
Fuse (40A)  
Remote output  
Car audio unit  
+12V car battery  
Tip  
If your car audio does not have remote output,  
connect the remote input terminal (REM) to  
the accessory power supply.  
8
EN  
4 Use your power  
amplifier  
Adjust input level  
To ensure sound quality, adjust input level to  
match it with the car audio’s output voltage.  
1 Check the line output voltage of the  
connected car audio.  
Select filter mode  
Select Filter Mode according to the connected  
speaker type.  
2 Rotate INPUT LEVEL to select a matched  
voltage: 0.3V to 6V.  
1 Slide FILTER MODE to the selected  
Adjust bass boost  
To enjoy more bass sound:  
position.  
HPF (high-pass-filter): Select this  
mode when mid-range speakers and  
tweeters are connected for high  
frequency output.  
LPF (low-pass-filter): Select this  
mode when woofer and subwoofer  
are connected for low frequency  
output.  
1 Set FILTER MODE at OFF or LPF mode.  
2 Slide BASS BOOST to 12dB position.  
Tip  
If BASS BOOST is set at 0dB position, no extra  
bass will be boosted.  
OFF (flat): Select this mode when  
both tweeters and woofers are  
connected.  
Note  
If FILTER MODE is set at HPF mode, the bass  
frequency will be filtered.  
Select LPF frequency  
When FILTER MODE is set at LPF position, you  
can select the range of frequency that is to be  
filtered.  
About the protector  
indicator  
The amplifier has a built-in protection circuit to  
protect the transistors and speakers in following  
conditions:  
Note  
When FILTER MODE is set at OFF or HPF  
position, LPF FREQUENCY does not work.  
The amplifier is overheated.  
A DC current is generated in  
speakers.  
1 Slide LPF FREQUENCY to the selected  
position.  
80Hz: More high frequency signal  
is filtered. Select 80Hz if you prefer  
stronger bass effect.  
180Hz: Less high frequency signal is  
filtered.  
The battery voltage is too low or too  
high. Or  
The speaker terminals are short  
circuited.  
When the PROTECTED indicator  
lights up in red, the amplifier shuts  
down automatically. In this case  
please:  
EN  
9
1 Take out the disc or tape and turn off the  
5 Product  
information  
car audio.  
2 Check the cause of the malfunction.  
3 If the amplifier is overheated, let it cool  
down.  
Note  
Product information is subject to change  
without prior notice.  
Replace fuse  
If there is no power, the fuse might be damaged  
and need to be replaced.  
Power output  
(RMS)  
- 4 ohm 75W x 2  
1 Pull out the damaged fuse.  
2 Replace the fuse with the supplied fuse or  
buy a new fuse that matches the rating of  
the damaged fuse (30A x 1).  
- 2 ohm 110W x 2  
- 4 ohm 220W x 1  
(bridged)  
Total harmonic  
distortion  
0.09%  
Signal to noise  
ratio  
100dB  
Channel separation  
Frequency  
response  
50dB  
5-50kHz  
Input sensitivity  
Input impedance  
Fuse rating  
Dimensions (D x  
W x H)  
300mV - 6V  
22k ohm  
30A x 1  
246 x 240 x  
54mm  
If the fuse gets damaged immediately after it  
has been replaced, the amplifier might have  
internal malfunction. Consult qualified personal  
for repair.  
Weight  
1.98kg  
10 EN  
6 Troubleshooting  
To keep the warranty valid, never try to repair  
the system yourself.  
If you encounter problems when using this  
apparatus, check the following points before  
requesting service. If the problem remains  
unsolved, go to the Philips web site  
(www.philips.com/welcome).When you  
contact Philips, ensure that the apparatus  
is nearby and the model number and serial  
number are available.  
Power indicator does not light up  
The connected car audio is not turned on.  
The fuse is blown. Replace the fuse with  
a new one.  
The input level is not set correctly (see  
“Adjust input level”).  
The protector indicator lights up in red.  
The speaker terminals are short circuited.  
Check the speaker connections.  
The sound is too low.  
The input level is not set correctly  
(see “Adjust input level”).  
The sound is interrupted or stopped suddenly.  
The thermal protector is activated.  
Reduce the volume.  
The ventilation outlet is blocked. Remove  
any obstructions from the outlet.  
Alternate noise is heard.  
The power connecting wires are installed  
too close to the RCA pin cords.  
The ground wire is not securely  
connected to a metal point of the car.  
Negative speaker wires touch the car  
chassis.  
The unit becomes abnormally hot.  
Place the amplifier in a well ventilated  
location.  
Use speakers with suitable impedance:  
2-8 ohm (stereo), 4-8 ohm (bridged).  
EN 11  
© 2010 Koninklijke Philips Electronics N.V.  
All rights reserved.  
CMQ205_00_UM_V1.0  

Rockford Fosgate PCH 514 User Manual
Raypak HI DALTA HD101 User Manual
Pioneer Car Video System XV HTD1 User Manual
Philips Blu ray Player bdp5000 User Manual
Philips 166V3L User Manual
Lochinvar KNIGHT 210 User Manual
KitchenAid KFPW760QBW1 User Manual
Kenwood SK EXCL1 User Manual
Kenwood KDC W4531 User Manual
JVC KD AR5500 User Manual