b
R - C H
L - C H
R - C H
L - C H
1
5
6
7
"
!
0
/
§ $ %
9
8
2
P
&
R
N
D
2
3
L
4
2
a
5mm
183 mm
53mm
b
2
c
3
4
English
8
Purple and Right speaker (Rear)
purple/black
wires
Install the car audio
2 Connect the other end of the supplied
These instructions are for a typical installation.
However, if your car has different requirements,
make the corresponding adjustment. If you have
any questions regarding installation kits, consult
your Philips car audio dealer.
standard connector to the car audio
b
system.
Connector/
Obeject
Connect to/with
1
2
Pink wire
Extension wire
2.5m extension Parking brake (-)
wire(Not
included)
1
Connect wires
1 Check the car’s wiring carefully, then
a
connect them to the supplied ISO wires.
3
4
5
Brake switch
Ground
Connector Connect to
ISO wires
Grey wire
Black wire
Connected in step 1
above.
1
2
Yellow wire The +12V car battery which
is live at all times.
6
7
Rear line out Left/
Right
Blue wire
The electric antenna control
lead or power supply lead of
the antenna booster
If there is no electric antenna
or antenna booster, or it is
manually operated telescopic
antenna, it is not necessary
to connect this lead.
Front line out Left/
Right
8
9
Blue cable
Red cable
Subwoofer
Aux Right
10 White cable
11 Yellow cable
12 Yellow cable
13 Yellow cable
14 Yellow cable
15 Purple wire
16 Gearbox switch
Aux Left
Video in
3
4
Black wire
Red wire
A metal surface of the car
First connect the black
ground (earth) lead, then
connect the yellow and red
power supply leads.
Camera in
Video out 1
Video out 2
Reverse camera (B+)
The +12V power terminal
which is live in the
accessory (ACC) position of
the ignition switch
If there is no accessory
position, connect to the
+12V car battery terminal
that is always live. Be sure
to connect the black ground
(earth) lead to a metal
surface of the car first.
17 Reverse gear
signal
Back lamp lead +
2
Mount in the dashboard
1 If the car does not have an on-board drive
or navigation computer, disconnect the
negative terminal of the car battery.
5
6
7
Green and Left speaker (Rear)
green/black
wires
2 Ensure that car dashboard opening is within
a
these measurements:
White and Left speaker (Front)
3 Slide the unit into the dashboard until a
white/black
wires
b
click sound is heard.
c
4 Attach the trim plate.
5 Reconnect the negative terminal of the car
Gray and
gray/black
wires
Right speaker (Front)
battery.
SetTime
Turn on
1 Touch [Set time].
2 Touch hour/minute digit to highlight the digit.
3 Touch / to set hour/minute.
1 Press to turn on the unit.
Set time format
1 Touch[Clock Mode]repeatedly to toggle
between [12Hr] and [24Hr] options.
Listen to Radio
2 Touch a language to select.
1 Touch to display home menu.
2 Touch [Radio].
•
To adjust screen brightness, press DIMMER
on the remote control, then press or
.
•
To turn off the unit, press and hold for 3
seconds.
Set date and time
1 Touch to display main menu.
3 Touch on FM or AM repeatedly on the left
of the screen to select band:
Radio
Disc
USB
SDHC
Sun
4 Briefly touch or to tune to a radio
Sep 27, 2009
station by step.
•
Touch or for over 1 seconds to
tune to a radio station automatically.
AV_IN1
Navigation
Settings
2 Touch [Settings].
3 Touch to access 2nd page.
3
Play disc
4 Touch [Date].
You can play video, audio or images stored on the
following discs:
•
•
•
DVD video, DVD-R, DVD-RW
VCD
Audio CD, CD-R, CD-RW
1 Insert the disc into the disc slot with label
side facing up.
Countries where you Supported DVD
bought the unit
region code
5 Touch year digit to highlight this digit.
China
6 Touch / to set year.
7 Repeat step 5 and 6 to set month and day.
Asia Pacific, Taiwan,
Korea
Receive call
By default, all incoming calls are received
automatically.
Latin America
Russia, India
1 If there is incoming call, [Incoming call...]
flashes on the screen. Speak into the
Bluetooth microphone.
2 When conversation ends, tap
(red) to
terminate the call.
4
Play USB device
Note
•
Ensure that the device contains playable
content.
1 Open the lid of USB socket.
2 Insert the USB to the USB socket.
Play with Bluetooth device
Pair the Bluetooth-enabled devices
1 Turn on the Bluetooth function on your
device.
2 Search for other Bluetooth device with
your device.
3 Select “CED1700” in the pairing list.
4 Enter default password “0000”.
Make a call
1 Touch on top of the screen.
2 Touch number icons directly to input
phone number.
3 After the phone number entered, touch
.
© 2010 Koninklijke Philips Electronics N.V.
All rights reserved.
Document order number: CED1700_00_QSG_V3.0
|