1 Important
Safety and important notice
Warning
This product complies with the radio interference
requirements of the European Community.
• Risk of overheating! Never install the product in a
confined space. Always leave a space of at least 4 inches
around the product for ventilation. Ensure curtains or
other objects never cover the ventilation slots on the
product.
• Never place the product, remote control or batteries
near naked flames or other heat sources, including direct
sunlight.
* Wireless and Ethernet LAN functions are
authorized for indoor use only.
Hereby, Philips Consumer Lifestyle, declares that
this wireless Blu-ray disc player (BDP9600) is in
compliance with the essential requirements and
other relevant provisions of Directive 1999/5/EC.
• Only use this product indoors. Keep this product away
from water, moisture and liquid-filled objects.
• Never place this product on other electrical equipment.
• Keep away from this product during lightning storms.
• Where the mains plug or an appliance coupler is used as
the disconnect device, the disconnect device shall remain
readily operable.
• Visible and invisible laser radiation when open. Avoid
Disposal of your old product and
batteries
exposure to beam.
• This product with Class I construction shall be connected
to a Mains socket outlet with a protective earthing
connection.
Health warning on viewing 3D
Your product is designed and manufactured with
high quality materials and components, which can
be recycled and reused.
•
If you or your family has a history of epilepsy
or photosensitive seizures, consult a medical
professional before exposing yourself to
flashing light sources, rapid image sequences
or 3D viewing.
To avoid discomfort such as dizziness,
headache or disorientation, we recommend
not watching 3D for extended periods of
time. If you experience any discomfort, stop
watching 3D and do not immediately engage
in any potentially hazardous activity (for
example driving a car) until your symptoms
have disappeared. If symptoms persist, do
not resume watching 3D without consulting a
medical professional first.
•
When this crossed-out wheeled bin symbol is
attached to a product it means that the product is
covered by the European Directive 2002/96/EC.
Please inform yourself about the local separate
collection system for electrical and electronic
products.
Please act according to your local rules and do not
dispose of your old products with your normal
household waste.
•
Parents should monitor their children during
3D viewing and ensure they do not experience
any discomfort as mentioned above. Watching
3D is not recommended for children under 6
years of age as their visual system is not fully
developed yet.
Correct disposal of your old product helps to
prevent potential negative consequences for the
environment and human health.
CLASS 1
LASER PRODUCT
4
EN
HDMI, and HDMI logo and High-Definition
Multimedia Interface are trademarks or registered
trademarks of HDMI licensing LLC.
Your product contains batteries covered by the
European Directive 2006/66/EC, which cannot be
disposed with normal household waste.
Please inform yourself about the local rules on
separate collection of batteries because correct
disposal helps to prevent negative consequences for
the environmental and human health.
DLNA®, the DLNA Logo and DLNA CERTIFIED®
are trademarks, service marks, or certification
marks of the Digital Living Network Alliance.
Copyright notice
The Wi-Fi CERTIFIED Logo is a certification mark
of the Wi-Fi Alliance.
This item incorporates copy protection technology
that is protected by U.S. patents and other
intellectual property rights of Rovi Corporation.
Reverse engineering and disassembly are prohibited.
Open source software
Philips Electronics Singapore Pte Ltd hereby offers
to deliver, upon request, a copy of the complete
corresponding source code for the copyrighted
open source software packages used in this product
for which such offer is requested by the respective
licenses.
Manufactured under license from Dolby
Laboratories. Dolby and the double-D symbol are
trademarks of Dolby Laboratories.
This offer is valid up to three years after
product purchase to anyone in receipt of this
information. To obtain source code, please contact
[email protected]. If you prefer not to
use email or if you do not receive confirmation
receipt within a week after mailing to this email
address, please write to “Open Source Team,
Philips Intellectual Property & Standards, P.O. Box
220, 5600 AE Eindhoven, The Netherlands.” If you
do not receive timely confirmation of your letter,
please email to the email address above.
Manufactured under license under U.S. Patent
#’s: 5,451,942; 5,956,674; 5,974,380; 5,978,762;
6,226,616; 6,487,535; 7,212,872; 7,333,929;
7,392,195; 7,272,567 & other U.S. and worldwide
patents issued & pending. DTS and the Symbol
are registered trademarks, & DTS-HD, DTS-HD
Master Audio, and the DTS logos are trademarks of
DTS, Inc. Product includes software. © DTS, Inc. All
Rights Reserved.
Trademark notice
ABOUT DIVX VIDEO: DivX® is a digital video
format created by DivX, Inc. This is an official DivX
Certified® device that plays DivX video. Visit divx.
com for more information and software tools to
convert your files into DivX video.
ABOUT DIVX VIDEO-ON-DEMAND: This DivX
Certified® device must be registered in order to
play purchased DivX Video-on-Demand (VOD)
movies. To obtain your registration code, locate the
DivX VOD section in your device setup menu. Go
to vod.divx.com for more information on how to
complete your registration.
‘Blu-ray’, ‘Blu-ray Disc’, ‘Blu-ray Disc’ logo, ‘Blu-ray
3D’ and ‘Blu-ray 3D’ logo are the trademarks of
Blu-ray Disc Association.
“Qdeo” and “QuiteVideo” are trademarks of
Marvell or its affiliates.
EN
5
DivX®, DivX Certified®, DivX Plus™ HD and
associated logos are registered trademarks of DivX,
Inc. and are used under license.
2 Your Blu-ray disc
player
Congratulations on your purchase, and welcome to
Philips!To fully benefit from the support that Philips
offers (e.g. product software upgrade), register your
BONUSVIEW™
‘BD LIVE’ and ‘BONUSVIEW’ are trademarks of
Blu-ray Disc Association.
If you contact Philips, you will be asked for the model
and serial number of this player.The model number
and serial number are on the back of this player.Write
the numbers here:
Model No. __________________________
Serial No. ___________________________
The USB-IF Logos are trademarks of Universal
Serial Bus Implementers Forum, Inc.
Feature highlights
For optimal performance of this player, it is
recommended to regularly update the software of
this player.
Qdeo video processing for movies in its purest
form
Qdeo processing produces an image that has
reduced noise, enhanced color, improved contrast,
fine detail and an enhanced sense of depth, resulting
a quite, pleasing and immersive viewing experience.
‘DVD Video’ is a trademark of DVD Format/Logo
Licensing Corporation.
3D Blu-ray disc play
This player can play 3D Blu-ray discs and it provides
a full HD 3D experience at home. Connect your
player to a 3D-compliant TV with an HDMI cable,
and wear 3D glasses that are compatible with the
TV to enjoy excitement of the 3D world.
Java and all other Java trademarks and logos are
trademarks or registered trademarks of Sun
Microsystems, Inc. in the United States and/or other
countries.
Net TV
Net TV brings you a wide range of online
information and entertainment on your TV which
is connected to this player. With Net TV you can
enjoy some of the best websites tailored to fit your
TV.
Online video store
Philips online video store gives you access to a wide
range of high quality movies that you can watch
directly on your TV.
•
This service is country dependent. Not all
countries have this service available.
DLNA
This Philips player has a built-in DLNA network link
to let you watch videos, view photos and listen to
music right from your PC. DLNA-certified products
offer expanded capabilities that enable it to play not
one but multiple roles in your digital home network.
6
EN
DivX Plus HD
d
e
Disc compartment
This player is a DivX Plus HD Certified device. It
plays all DivX video including DivX Plus HD video
files (H.264 video with the .mkv file extension and
AAC audio) up to 1080p and premium Hollywood
content.
•
•
•
•
Open or close the disc compartment .
f
g
h
Start or resume play.
Pause play.
High fidelity 7.1 channel surround sound
This player supports the high-definition audio such
as Dolby TrueHD and DTS-HD Master Audio.
jack
Connect a USB device.
Playable media
This player can play:
Remote control
•
•
BD-Video, BD-R/RE2.0, BD 3D
DVD, DVD-Video, DVD+R/+RW, DVD-R/-
RW, DVD+R/-R DL (Dual Layer)
Video CD/SVCD
a
b
c
•
•
Audio CD, CD-R/CD-RW, MP3 media, WMA
media, JPEG files
•
•
DivX (Ultra)/DivX Plus HD media, MKV media
USB flash drive
d
e
Region codes
You can play discs with the following region codes.
e
Region code
DVD
Country
q
p
f
g
BD
Russia, India
C
h
i
j
o
n
j
Product overview
Main unit
k
l
m
d
a
b
c
e f g h
a
•
Turn on this player or switch to standby
mode.
a
•
•
Turn on this player or switch to standby
b
c
Display panel
IR sensor
mode.
When EasyLink is enabled, press and
hold for at least three seconds to turn all
connected HDMI CEC compliant devices
to standby.
•
Detect signals from the remote control.
Always point the remote control at the
IR sensor.
EN
7
b
c
3 Connect
•
Access the home menu of this player.
DISC/POP-UP
•
•
Make the following connections to use this player.
BD: Access or exit the pop-up menu.
DVD: Access or exit the disc menu.
Basic connections:
•
•
•
Video
Audio
Power
d
e
/
/
/
•
•
Navigate through the menus.
Optional connections:
/
•
Route audio to other devices
Skip to the previous or next title, chapter,
or track.
•
•
•
•
HDMI-compliant AV receiver/amplifier
Multi-channel AV amplifier/receiver
Digital AV amplifier/receiver
Analog stereo system
f
•
Access options for the current activity or
selection.
•
•
USB device
g
h
i
Wired/Wireless network
•
•
Return to a previous display menu.
Search backward or forward.
/
Note
• Refer to the type plate at the back or bottom of the
product for identification and supply ratings.
•
•
Stop play.
Press and hold to open/close the disc
compartment.
• Before you make or change any connections, ensure that
all the devices are disconnected from the power outlet.
j
k
Color buttons
Connect video/audio cables
Select the best video connection that theTV can
support.
•
BD: Select tasks or options.
Alphanumeric buttons
•
•
•
Select an item to play.
Enter values.
Enter letters via SMS style entry.
•
•
Option 1: Connect to the HDMI jack (for a
HDMI, DVI or HDCP-compliant TV).
Option 2: Connect to the component video
jacks (for a standard TV or Progressive Scan
TV).
Option 3: Connect to the composite video
jack (for a standard TV).
l
AUDIO
Select an audio language or channel on
a disc.
SUBTITLE
•
•
m
n
o
•
Select a subtitle language on a disc.
Option 1: Connect to the HDMI jack
•
Start or resume play.
•
•
Pause play.
Move the paused picture forward frame
by frame.
p
q
TOP MENU
•
•
BD: Display the top menu.
DVD: Display the title menu.
OK
•
HDMI IN
Confirm an entry or selection.
1
Connect an HDMI cable (not supplied) to:
•
•
the HDMI jack on this player.
the HDMI input jack on the TV.
8
EN
Option 3: Connect to the composite
video jack
Tip
• If the TV has a DVI connector only, connect via an
HDMI/DVI adaptor. Connect an audio cable for sound
output.
• If there is a blank TV screen under HDMI connection,
on the remote control press and then press “731”
(numeric buttons) to recover picture display.
• If this player connects to a TV compatible with 1080p
or 1080p/24Hz, Philips recommends HDMI category
2 cable, also known as High Speed HDMI cable, for
optimal video and audio output.
AUDIO IN
VIDEO IN
• To play the digital video images of a BD-video or DVD-
video via an HDMI connection, it is necessary that both
this player and the display device (or an AV receiver/
amplifier) support a copyright protection system called
HDCP (high-bandwidth digital content protection system).
• This connection provides the best picture quality.
Option 2: Connect to the component
video jacks
1
2
Connect a composite video cable (not
supplied) to:
Y
•
•
the VIDEO jack on this player.
AUDIO IN
Pb
the VIDEO input jack on the TV.
Connect the audio cables (not supplied) to:
Pr
•
the Audio LINE OUT- L/R jacks on this
player.
the AUDIO input jacks on the TV.
•
Tip
• The video input jack on the TV might be labeled as A/V
IN, VIDEO IN, COMPOSITE or BASEBAND.
Route audio to other devices
You can route the audio from this player to other
1
2
Connect the component video cables (not
supplied) to:
devices.
•
•
the Y Pb/Cb Pr/Cr jacks on this player.
the COMPONENT VIDEO input jacks
on the TV.
Connect to an HDMI-compliant AV
receiver/amplifier
Connect the audio cables (not supplied) to:
•
the Audio LINE OUT -L/R jacks on this
player.
the AUDIO input jacks on the TV.
•
Tip
• The component video input jack on the TV might be
labeled as Y Pb Pr or YUV.
HDMI IN
EN
9
1
Connect an HDMI cable (not supplied) to:
Connect to a digital AV amplifier/receiver
Connect to coaxial jack
•
•
the HDMI jack on this player.
the HDMI jack input jack on the device.
Tip
COAXIAL
• The HDMI connection provides the best audio quality.
Connect to a multi-channel AV receiver/
amplifier
1
Connect a coaxial cable (not supplied) to:
•
•
the COAXIAL jack on this player.
the COAXIAL/DIGITAL input jack on
the device.
Connect to optical jack
7.1 CH AUDIO INPUT
OPTICAL
1
Connect the 7.1-channel audio cables (not
supplied) to:
•
the 7.1 CH AUDIO OUTPUT jacks on
this player.
1
Connect an optical cable (not supplied) to:
•
•
the OPTICAL jack on this player.
the OPTICAL/DIGITAL input jack on the
device.
•
the corresponding AUDIO input jacks on
the device.
Tip
Connect an analogue stereo system
• To connect 5.1-channel AV receiver/amplifier, connect
the 7.1-channel audio jacks except the SL/SR jacks.
• You can optimize the speaker output (see “Adjust
settings” >[Audio]> [Speaker Setup]).
AV IN
1
Connect the audio cables (not supplied) to:
•
the Audio LINE OUT-L/Rjacks on this
player.
•
the AUDIO input jacks on the device.
10 EN
4 Get started
Connect a USB device
1
Connect a USB device to the
on the front panel of this player.
(USB) jack
Caution
• Use of controls or adjustments or performance of
procedures other than herein may result in hazardous
radiation exposure or other unsafe operation.
Note
• Press , and select [browse USB] in the menu to access
the content and play the files.
Always follow the instructions in this chapter in
sequence.
• Connect a USB device only to the
jack on this player.
• Philips does not guarantee compatibility with all USB
devices.
Prepare the remote control
1
Press
at the back of the remote control to
Connect a network
open the back cover.
With a wired or wireless connection (see “Get
started” > “Set up a network”), you can connect
this player to:
•
the Internet (for software update/BD
Live/Net TV service).
•
or a home network (to access media files
from a DLNA media server, e.g. PC).
Note
• Internet access to Philips website for software update
may not be allowed, depending on the router you use
or the Internet Service Provider’s policy. Contact your
Internet Service Provider for more information.
2
3
Insert two AAA batteries with correct
polarity (+/-) as indicated.
Replace the back cover.
Connect power
Note
• If you are not going to use the remote control for a long
time, remove the batteries.
Caution
• Do not mix batteries (old and new or carbon and alkaline,
• Risk of player damage! Ensure that the power supply
voltage corresponds to the voltage printed on the back
of the unit.
etc.).
• Batteries contain chemical substances, so they should be
disposed of properly.
• Before connecting the AC power cord, ensure you have
completed all other connections.
Find theTV input
Note
1
2
Press to turn on this player.
Turn on the TV and switch to the video input
(refer to the TV user manual on how to select
the A/V input).
• The type plate is located on the back of the player.
1
Connect the AC power cable to:
•
•
this player.
First time use
the wall socket.
This player is ready to be set up for use.
When you turn on this player for the first time or
this player is reset to the default setting, you are
prompted to select a menu display language and
then a country.
»
EN 11
Use the Home menu
1
Press to display the home menu.
•
•
To start disc play, select [Play Disc].
To play the USB contents, select [browse
USB].
To access the setup menus, select [Setup].
To access media files from a DLNA media
server (e.g. PC), select [browse PC].
To access the Net TV services on the
Internet, select [browse Net TV].
•
The language options may vary from
different regions.
4
Press
OK.
/
to select a language, and press
•
•
Set up a network
You can connect this player to the Internet (for
software update/BD Live/NetTV service), or to a
home network (to access media from a DLNA media
server, e.g. PC).
•
Navigate a menu
1
When a menu is displayed, press the buttons
on the remote control to navigate.
To access media from your PC, you need to ensure:
•
a media server software (e.g. Windows
Media Player 11) is installed on your PC;
and the media server software is
configured to enable media sharing (See
the “Help” documentation from the
media server software).
Button
Action
•
Move up or down.
Move left or right.
Confirm a selection.
Enter numbers/letters/text.
/
/
OK
Set up a wired network
Note
• Ensure that the network cables are properly connected.
Select a menu display language
1
Connect a network cable (not supplied) to:
•
•
the LAN port on this player.
the LAN port on a router with Internet
connection.
Note
• If this player is connected to an HDMI CEC compliant
TV, and you select [Auto] for the [Menu Language],
it switches automatically to the same menu display
language as per your TV setting.
2
3
To access media files from your computer,
connect the computer to the router.
Turn on this player, the computer and the
router.
1
In the Home menu, select [Setup] and press
OK.
2
3
Select [Preference], and press
Select [Menu Language], and press
.
.
12 EN
Install the network connection
For the first time you connect the network, install
the network connection.
1
2
3
4
5
Set up a wired or wireless network.
Press to display the home menu.
Select [Setup] and press OK.
Select [Network], and press OK.
Select [Network Installation], and press OK.
Tip
• The wired network ensures the best performance for
data transmission between the devices.
Set up a wireless network
6
Follow the on-screen instructions to complete
the network installation.
Note
»
After the network installation completes,
you can access the services: browse NetTV,
browse PC, BD-Live, software updates.
• Ensure that this player and the router and the PC are all
switched on.
Tip
• You can check the status of the wired or wireless
connection of this player (see “Adjust settings” >
“Network Setup” > [View Network Settings] or
[View Wireless Settings]).
Use Philips EasyLink
This player supports Philips EasyLink which uses the
HDMI CEC (Consumer Electronics Control) protocol.
You can use one single remote control to control
EasyLink-compliant devices that are connected
through HDMI connectors.
Note
Tip
• To enable the EasyLink feature, you must turn on the
HDMI CEC operations on the TV and on other devices
connected to TV. Refer to the TVs/devices manual for
details.
• The wireless performance can vary due to bandwidth
connection, network traffic and some environmental
effects, such as surrounded by metal panel or heavy
concrete, radio interference and coverage distance.
EN 13
One-touch play
5 Play
Play a disc
1
Press (standby) to turn on this player.
»
TheTV (if theTV supports one-touch play)
automatically turns on and switches to the
correct video-in channel.
Caution
»
If a disc is loaded, disc play automatically
starts.
• Do not insert any objects other than discs into the disc slot.
One-touch standby
1
Press on the front panel to open the disc
compartment.
1
Press and hold (standby) for more than
3 seconds.
•
You may also press and hold
on the
remote control to open/close the disc
compartment.
»
All the connected devices (if the device
supports one-touch standby) automatically
switch to standby.
2
3
Insert a disc with its label facing up.
Start disc play.
•
To stop disc play, press
.
Note
• Philips does not guarantee interoperability with all HDMI
CEC devices.
Note
• Check disc/file formats supported (see “Your Blu-ray disc
player” > “Playable media”).
• If the password entry menu is displayed, enter the
password before you can play the locked or restricted
disc (see “Adjust settings” > “Preference Setup” >
[Parental Control] ).
• If you pause or stop a disc, the screen saver appears after
10 minutes of inactivity. To deactivate the screen saver,
press any button.
• After you pause or stop a disc and no button is pressed
within 30 minutes, this player automatically switches to
standby.
Play from a USB device
Play or view media files on the following USB devices:
•
•
•
flash drive
memory card reader
HDD (This player can detect only a portable
hard disc drive with USB power peak current
no more than 500mA.)
1
2
Connect a USB device to the
(USB) jack.
Press , and select [browse USB], and press
OK.
»
A contents menu is displayed.
14 EN
3
Select a file to play, and press OK.
Note
»
Play starts (see “Play video”,“Play photo”,
Play music” for details).
• Some operations may not work with some discs. See the
information accompanying the disc for details.
•
To stop play, press
device.
or remove the USB
Display menu
Note
• Philips does not guarantee compatibility with all USB
devices.
• Not all digital cameras are supported. Digital cameras that
require PC programme installation are not supported.
BD-video disc
•
TOP MENU stop the video play and shows
the disc menu. This feature is disc-dependent.
POP-UP MENU access to the BD-video disc
menu without interrupting disc play.
Play video
Control video play
•
1
Play a title.
DVD-video disc
•
•
2
Use the remote control to control the play.
TOP MENU display the root menu of a disc.
DISC MENU display disc information and
guide you through the available functions in
the disc.
Button
Action
Pause play.
•
Press repeatedly
to slow
VCD/SVCD/DivX disc:
•
forward play frame by frame.
DISC MENU display the content of the disc.
Start or resume play.
Stop play.
Tip
Skip to a previous/next title or chapter.
/
• If the PBC setting is off, the VCD/SVCD skips the
menu and starts play from the first title. To display the
menu before play, turn on the PBC setting (see “Adjust
settings” > [Preference] > [VCD PBC]).
Search fast-backward or fast-forward.
Press repeatedly to change the search
speed.
/
•
Press once , and then press
repeatedly to slow play
backward or forward.
/
Display play information
1
During play, press
The play options menu is displayed.
Select [Info] in the menu, and press OK.
The current status of disc play is displayed.
.
»
Note
2
»
• For BD discs with Java application, availability of the play
resume function depends on specific discs.
Select a title/chapter
1
2
3
During play, press
.
Change video play
»
The play options menu is displayed.
1
Play a title.
Select [Titles] or [Chapters] in the menu, and
press OK.
Select the title or chapter number, and press
OK.
2
Use the remote control to change the play.
Button
AUDIO
Action
Directly select an audio language or
channel on a disc.
Directly select a subtitle language
on a disc.
Skip play to a specific time
SUBTITLE
1
During play, press
.
»
The play options menu is displayed.
Access the above mentioned
actions or more options (e.g. repeat
or shuffle play mode).
2
Select [Time Search] in the menu, and press
OK.
EN 15
3
Press the Navigation buttons (
/
) to
2
3
Select [Subtitle Shift] in the menu, and press
change the time to skip to, and press OK.
OK.
Press the Navigation buttons (
the subtitle, and press OK.
/
) to shift
Zoom in/out
1
During play, press
»
.
The play options menu is displayed.
Tip
2
3
Select [Zoom] in the menu, and press OK.
• Subtitle shift is not supported for DivX video with external
subtitles.
Press the Navigation buttons (
/
)to select
a zoom factor, and press OK.
4
Press the Navigation buttons to navigate in
Sync audio output with video play
If a video play is slower than audio output (sound
does not match with the pictures), you can delay
the audio output to match the video.
the zoomed picture.
•
To cancel zoom mode, press to display
the zoom factor bar, and press the
Navigation buttons (
/
) until the
zoom factor [x1] is selected.
1
During play, press
.
»
The play options menu is displayed.
Repeat play for a specific section
2
Select [Audio Sync] in the menu, and press
1
2
3
During play, press
.
OK.
»
The play options menu is displayed.
»
A slider bar is displayed
Select [Repeat A-B] in the menu, and press
OK to set the starting point.
3
Press the Navigation buttons (
/
) to to
move the slider until the sound can match the
pictures.
Forward the video play, and press OK to set
the ending point.
»
Repeat play starts.
Play BD-video
•
To cancel repeat play mode, press ,and
select [Repeat A-B] and press OK.
Blu-ray video disc has a larger capacity and supports
features such as high-definition videos, multi-
channel surround sounds, interactive menus and
so on.
Note
1
2
3
Insert a BD-video disc.
Press , select [Play Disc] and press OK.
Play automatically starts, or select a play
option in the menu and press OK.
• The marked section for repeat play is only possible
within a track/title.
View video play from different camera
angles
•
During play, you can press TOP MENU
to display additional information, features
or content stored in the disc.
During play, you can press POP-UP
MENU to display the disc menu without
interrupting disc play.
1
During play, press
.
•
»
The play options menu is displayed.
2
3
Select [Angle List] in the menu, and press
.
Select an angle option, and press OK.
Enjoy Blu-ray 3D video
This player can play Blu-ray 3D videos.
»
Play changes to the selected angle.
1
Ensure that the TV is 3D and HDMI compliant,
and connect the TV to this player through an
HDMI cable.
Turn on Blu-ray 3D output (see “Adjust
settings” > [Video] > [Blu-ray 3D video]).
Note
• Applicable only to discs that contain multi-angle scenes.
2
3
Manually shift subtitle display
Wear 3D glasses that are compatible with the
TV for viewing.
You can manually adjust the subtitle position on the
TV screen.
1
During play, press
.
»
The play options menu is displayed.
16 EN
Enjoy BONUSVIEW
Play photo
Play photo as slideshow
You can play JPEG photos (files with .jpeg or .jpg
extensions).
(Applicable only to a disc compatible with the
BONUSVIEW or Picture-in-Picture feature)
You can instantly view additional content (such as
commentaries) in a small screen window.
1
Press
.
1
Insert a disc or USB device that contains the
JPEG photos.
»
The play options menu is displayed.
2
Select [PIP Selection] in the menu, and then
2
Press , select [Play Disc] or [browse USB],
select [PIP], and press OK.
and press OK.
»
The secondary video window is turned on.
»
A contents menu is displayed.
3
4
Select [2nd Audio Language] or [2nd Subtitle
Language] in the menu, and press
Select the language to play, and press OK.
3
4
Select a photo folder, and press OK to enter.
.
•
To select a photo, press the Navigation
buttons.
Press OK to start slideshow play.
Enjoy BD-Live
(Applicable only to a disc that enables BD-Live
bonus content. Ensure that this player is connected
to the Internet.)
Note
Additional contents (such as movie trailers,
subtitles, etc.,) can be downloaded to this player’s
local storage or a connected USB storage device.
Special video data may be played while they are
being downloaded.
When the disc supporting BD-Live is played, this
player or disc’s ID can be sent to the content
provider via the internet. Services and functions to
be provided vary from disc to disc.
• It may require longer time to display the disc content on
the TV if large number of songs/photos compiled onto
one disc.
• This player can only display digital camera pictures
according to the JPEG-EXIF format, typically used by
most digital cameras. It cannot display Motion JPEG,
or pictures in formats other than JPEG, or sound clips
associated with pictures.
• Folders/files that exceed the supported limit of this player
cannot be displayed or played.
Play DivX® video
Control photo play
DivX video is a digital media format that retains
high quality despite a high rate of compression.
1
Play a photo slideshow.
•
•
Press to access play options, select an
option, and press OK.
1
Insert a disc or USB device that contains the
DivX videos.
During slideshow play, you may also
press
/
to flip a photo horizontally/
2
Press , select [Play Disc] or [browse USB],
vertically.
and press OK.
•
If the slideshow stops, press to continue
play.
»
A contents menu is displayed.
3
4
5
Select a video folder, and press OK.
Select a title to play, and press OK.
Use the remote control to control the play.
Set a slideshow interval and animation
1
During play, press
.
»
The play options menu is displayed.
Button
AUDIO
Action
2
Select [Duration per slide] in the menu, and
press OK.
Select an audio language or channel.
SUBTITLE Select a subtitle language.
3
4
Select a duration, and press OK.
Select [Slide Animation] in the menu, and
press OK.
Stop play.
Note
5
Select a type of animation effect, and press
OK.
• You can only play DivX videos that were rented or
purchased with the DivX registration code of this player
(see “Adjust Settings” > [Advanced] > [DivX® VOD
Code]).
• You can play DivX video files of up to 4GB.
• This player can display up to 45 characters in the subtitle.
EN 17
4
Select a file to play, and press OK.
To return to the main menu, press
Play a musical slideshow
Create a musical slideshow to play simultaneously
MP3/WMA music files and JPEG photo files.
•
.
Note
Note
• For disc recorded in multiple sessions, only the first
session is played.
• For a WMA file that is protected by Digital Rights
• To create a musical slideshow, you must store the MP3/
WMA and JPEG files on the same disc or USB device.
Management (DRM), it cannot be played on this player.
• This player does not support MP3PRO audio format.
• For any special character that is present in the MP3 track
name (ID3) or album name, it might not be displayed
correctly on the screen because these characters are not
supported.
1
2
3
Play MP3/WMA music.
Press to return to the main menu.
Navigate to enter a photo folder, and press
• Folders/files that exceed the supported limit of this player
OK to start slideshow play.
cannot be displayed or played.
»
Slideshow begins and continues till the end
of the photo folder.
»
Audio continues to play until the end of
the disc.
Browse PC
With a home network, you can play videos /music /
photos which are streamed from a DLNA media
server (e.g. PC) to yourTV through this DLNA
certified player.
•
•
To stop the slideshow play, press
To stop the music play, press
.
again.
Play music
Note
Control a track
1
Play a track.
• To browse a PC, ensure that a DLNA media server
software (e.g. Windows Media Player 11) is installed on
the PC.
2
Use the remote control to control the play.
Button
Action
Pause play.
Start or resume play.
Stop play.
Skip to a previous/next track.
Select an item to play.
1
2
Set up a home network (see “Get started” >
“Set up a network”).
•
Make sure that you have completed the
network installation.
On your PC, in the DLNA media server
software, you need to set:
/
a
b
Share my media to this player (see
“Help” information in the media server
software).
Share files or add files to the library (see
“Help” information in the media server
software).
Search fast-backward or fast-
forward. Press repeatedly to
change the search speed.
Access the repeat or shuffle
play mode.
/
3
4
Press to display the home menu.
Select [browse PC], and press OK.
»
This player automatically scans, and displays
a list for the available networked devices.
Play MP3/WMA music
MP3/WMA is a type of compressed audio file (files
with .mp3, .wma extensions).
5
6
7
Select your DLNA media server (i.e. your PC)
from the list, and press OK.
Select a media file from the DLNA media
server (i.e. your PC).
1
Insert a disc or USB device that contains the
MP3/WMA music.
Press OK to start play.
2
Press , select [Play Disc] or [browse USB],
•
You may control play with play features
(see “Play video”, “Play photo”, “Play
music” for details).
and then press OK.
»
A contents menu is displayed.
3
Select a music folder, and press OK.
18 EN
Browse another country
Browse NetTV
Connect this player to the Internet to access the Net
TV online service, such as movies, pictures, music
infotainment.You can enjoy NetTV on yourTV which
is connected to this player.
On the Browse all page, you can switch the Net
TV country. Another country might have different
services.
Mark favorites
You can mark up to 12 services. Only Net TV
services can be marked as a favorite. Advertisement
and open Internet websites cannot be marked.
1) Select the icon for a service.
Note
• Because Net TV is an online system, it can be modified
over time to better serve its purpose.
• Some Net TV services can be added, changed or stopped
after some time.
2) Press to select Mark favorite, and press OK.
•
To unmark a favorite, press to select the
unmark action and press OK.
• For Net TV, You cannot download and save files nor install
plug-ins.
Open Internet websites
1
Set up a network (see “Get started” > “Set up
a network”).
With Net TV you can link up to the open Internet.
You can view any website. Remember that most
Internet websites are not tailored to be viewed on
a TV screen.
•
Make sure that you have completed the
network installation.
2
3
Press to display the home menu.
Select [browse Net TV], and press OK.
1) On the Browse all page, select Browse Internet,
and press OK.
2) On the on-screen keyboard, select a character
and press OK. Repeat Step 2 to enter a web
address.
»
»
This player starts to connect to NetTV and
opens the start page.
For first use, follow the on-screen
instructions to complete the registration,
and then switch on parental control to lock/
unlock the services offered on the NetTV
pages.
•
•
To delete input text, press
BACK.
To navigate to the available links on a open
internet page, press
/
/
/
on the
remote control, and press OK to open
the link.
4
After the start page opens, use the remote
control to browse Net TV.
Access online video stores
This service is country dependent.
Button
Action
With an SD card inserted as extension memory,
you can watch the rented movies instantly
through Net TV and the movies are automatically
downloaded into the SD card.
1) Insert a blank SD card to the SD CARD jack on
the rear panel of the player.
Select a service, or an item on
Internet pages.
Confirm a selection.
Return to a previous page, or
delete input text.
Access actions related to a
current activity.
/
/
/
OK
Enter number/letter (e.g. email
address and lock/unlock code).
The Net TV start page
Show your favorite services and some
recommended services.
2) On the Browse all page, select Video Store and
The Browse all page
You can view all the Net TV services by category.
The favorite services are marked as a star icon.
then select a video to play.
»
During play, the video is automatically
downloaded into the SD card.
EN 19
Clear history
Note
Clear the Parental control code, passwords,
cookies and history.
• This player has a standard SD card slot and the SD card
is solely for use in Videostore.
1) Press to display the home menu.
2) Select [Setup] > [Network] > [Clear Net TV
Memory].
• Use a blank SD memory card.
• The SD card should have a minimum storage capacity of
4 GB. For high-definition video, make sure that you use
an SD card with a minimum capacity of 8 GB.
• Incorrect insertion of the SD card may damage your
SD card.
Note
• Any existing content stored on the SD card will be
erased prior to the download of rented videos.
• If you clear the Net TV memory with Clear history, you
need to redo the first use registration when you link up
to Net TV again. If you have registered before, you can
restore your former favorite services and former locks.
Note
• Koninklijke Philips Electronics N.V. bears no responsibility
regarding the content and the quality of the content
provided by the content service providers.
Parental control
You can lock Net TV services and service
categories. When a service is locked, you need to
enter a code to open the service or category.
1) Switch on the Parental control:
a. On the Net TV start page, press , select
Enable parental control and press OK.
b. With the keypad on the remote control,
enter a 4 digit code as lock/unlock code.
c. Enter the same code to confirm.
2) On the Net TV start page or Browse all page,
select a service or category.
3) Press , select Lock service and press OK.
»
A lock symbol appears on top of the service
icon.
•
To unlock a service or category, select the
service and press OPTIONS and select
Remove lock.
Note
• Only services on the Net TV pages can be locked.
Advertisement and open Internet websites can not be
locked.
• Services are locked per country. Categories are locked
for all countries.
• When you have registered Net TV and you switch
off Parental control in the Options menu, all locks
are remembered and available again when you switch
Parental control back on.
20 EN
6 Adjust settings
Note
• If [4:3 Panscan] you have selected is not supported
by the disc, the screen displays in the [4:3 Letterbox]
format.
Note
• If the setup option is grayed out, it means the setting
cannot be changed at the current state.
[HDMI Video]
Select an HDMI video output resolution that is
compatible with your TV display capability.
•
[Auto] - Detect and select the best supported
video resolution automatically.
Video setup
1
2
3
Press
.
•
•
[Native] - Set to original video resolution.
[480i/576i], [480p/576p], [720p], [1080i],
[1080p], [1080p/24Hz] - Select a video
resolution setting that best is supported by the
TV. See the TV manual for details.
Select [Setup], and press OK.
Select [Video], and press
.
Note
• If a selected video resolution is not supported with
your TV and a blank screen appears, to recover picture
display, wait for 10 seconds, or on the remote control
press and then press “731” (numeric buttons).
Optimal
Personalized
Blu-ray 3D Video
[HDMI Deep Color]
This feature is available only when the display
device is connected by an HDMI cable, and when it
supports deep color feature.
•
[Auto] - Enjoy vivid images in over a billion
colors on Deep Color enabled TV.
Select an option, then press OK.
Select a setting, then press OK.
4
•
[On] - Enjoy vivid images in over a billion colors
on Deep Color enabled TV. Output 12 bit
color that reduces the posterization effect.
[Off] - Output standard 8 bit color.
•
•
To return to the previous menu, press
.
To exit the menu, press
.
[TV Display]
•
Select a display format:
[Component Video]
Select a component video output resolution that is
compatible with the TV display capability.
•
[480i/576i], [480p/576p], [720p], [1080i] -
Select a video resolution setting that is best
supported by the TV. See the TV manual for
details.
Note
• If the setting is not compatible with the TV, a blank
screen appears. Wait for 10 seconds for auto recovery.
• Copy protected DVDs can only output 480p/576p or
480i/576i resolution.
•
[4:3 Letterbox] – For 4:3 screen TV: wide-
screen display with black bars on the top and
bottom of the screen.
•
•
•
[4:3 Panscan] – For 4:3 screen TV: full-height
display with the trimmed sides.
[Picture Settings]
Select a predefined set of picture color settings.
[16:9 Widescreen] – For wide-screen TV:
display picture at ratio 16:9.
[16:9] – The display picture is at the disc native
aspect ratio (e.g. ratio 4:3, with black bars on
the left and right side of the screen).
•
[No optimization] - Switch off all
improvements.
•
•
[Animation] - Ideal for animated pictures.
[Documentary] - Ideal for nature and scenery.
EN 21
•
•
•
[Internet video] - Ideal for videos obtained
from the Internet.
[Optimal] - The best performance for most
movies and TV series.
[Personalized] - Use your personal customized
settings.
[Personalized]
Customize your own picture settings.
Note
• This feature only works when [Personalized] under
4
5
Select an option, and press OK.
Select a setting, and press OK.
[Picture Settings] is selected.
•
•
To return to the previous menu, press
.
•
•
•
[Brightness] - Set the brightness of video.
[Contrast] - Set the contrast of the video
[Saturation] - Set the color saturation of the
video.
[Artifact reduction] - Reduce artifact.
[Noise reduction] - Reduce noise in digital
video.
[ACE] - Adapt contrast enhancement to
enhance details in dark area but not affect the
details in bright area.
[Sharpness] - Enhance detail, depth and
perceived sharpness in the video.
[Color] - Set the color tone of the video.
To exit the menu, press
.
[Night Mode]
Increase a soft sound level such as dialogue to
make it easier to hear at a low volume, while
simultaneously decreasing a loud sound level.
•
•
•
[Auto] - Detect and select a best sound level
at a low volume. Applicable to tracks with
Dolby TrueHD audio only.
•
•
•
[On] - For quiet viewing at night.
[Off] - For surround sound with a full dynamic
•
•
range.
Note
•
•
•
•
•
[Standard] - No change on color tone.
[Nature] - Enhance green and blue.
[Cartoons] - Enhance all except skin tone.
[Cold] - Enhance blue color.
• Applicable only to Dolby encoded DVD-video or
BD-video.
[Warm] - Enhance red color.
[Neo 6]
[Blu-ray 3D video]
A post processing by DTS to generate a surround
sound effect from 2 channel audio.
Set to 2D or 3D output when playing a Blu-ray 3D
disc.
•
•
•
[Cinema] - Enable Neo 6 post processing to
the cinema mode.
•
[Auto] - Enable 3D output if a Blu-ray 3D
disc is loaded and the TV is 3D and HDMI
compliant, and the TV is connected through
an HDMI cable. Otherwise, only 2D output
is made.
[Music] - Enable Neo 6 post processing to the
music mode.
[Off] - Disable Neo 6 post processing.
[HDMI Audio]
•
[Off] - Turn off 3D output to enable 2D output.
Select an HDMI audio output when you connect this
player and the TV/audio device with an HDMI cable.
•
[Bitstream] - If the connected HDMI
device supports the appropriate HD audio
decoder,the original audio format on the disc is
sent. Otherwise, LPCM is sent.
[Auto] - Detect and select the best supported
audio format automatically.
Audio setup
1
2
3
Press
Select [Setup], and press OK.
Select [Audio], and press
.
.
•
22 EN
[Digital Audio]
Tip
Select an audio format for the sound output from
the DIGITAL OUT jack (coaxial/optical).
• The test tone is emitted from the speaker while adjusting
the volume level.
•
[Auto] - Detect and select the best supported
audio format automatically.
[PCM] - The audio device does not support
multi-channel format. Audio is downmixed to
two-channel sound.
[Bitstream] - Select the original audio to
experience Dolby or DTS audio (BD-video
special sound effect is disabled).
• Allow 1ms setting for every 30cm distance between the
speaker and the listening position.
•
Network setup
•
1
2
3
Press
.
Select [Setup], and press OK.
Select [Network], and press
.
Note
Network Installation
Video
• Ensure that the audio format is supported by the disc
and the connected audio device (amplifier/receiver).
• When [Bitstream] is selected, interactive audio like
button sound is muted.
View Network Settings
Audio
View Wireless Settings
Network
EasyLink
Preference
Advanced
Net TV User Location
Clear Net TV Memory
[PCM Downsampling]
Set the sampling rate for PCM audio output from
the DIGITAL OUT jack (coaxial/optical).
•
•
[On] - PCM audio is down-sampled at 48kHz.
[Off] - For BD or DVD recorded in LPCM
without copyright protection, two-channel
audio signals up to 96 kHz are output as LPCM
signals with no conversion.
4
5
Select an option, and press OK.
Select a setting, and press OK.
[Speaker Setup]
•
•
To return to the previous menu, press
.
Optimize the surround output for the connected
speaker system.
To exit the menu, press
.
[Network Installation]
•
[Speaker Setup] - Activate the test tone for
the speakers and the subwoofer.
Install the network connection.
[View Network Settings]
•
[Speaker Distance] - Set the delay time for
the speakers and the subwoofer if they are
placed closer to the listening position, so that
the sound output from all speakers reach the
listening position at the same time.
[Speaker Volume] - Set the volume level of
the speakes and the subwoofer to get the ideal
audio balance.
Display the information for the current network
status and the MAC address of this player.
[View Wireless Settings]
Display the information for the current Wi-Fi status.
[Net TV User Location]
•
•
Select the location of the Philips server which
provides Net TV services.
If your country location is not in the list, select
[International].
[Speaker Size]
•
Set the speaker size for the speakers and
the subwoofer.
[Clear Net TV Memory]
Clear the cookies, history, data you input for Net
TV which are stored in the cache area of the web
browser.
•
Select [Large] size for speakers that can
produce low frequency signal below
120 Hz.
•
•
•
Select [Off] if there is no speaker
connected.
EasyLink setup
1
2
3
Press
.
If the front speakers are set to [Small],
the subwoofer setting is [On] by default.
If the subwoofer is set to [Off], the front
speakers settings are [Large] by default.
Select [Setup], and press OK.
Select [EasyLink], and press
.
EN 23
EasyLink
On
On
Video
Audio
One Touch Play
One Touch Standby
On
Network
EasyLink
Preference
Advanced
4
5
Select an option, and press OK.
Select a setting, and press OK.
4
5
Select an option, then press OK.
•
•
To return to the previous menu, press
.
Select a setting, then press OK.
To exit the menu, press
.
•
•
To return to the previous menu, press
.
[EasyLink]
To exit the menu, press
.
This player supports Philips Easylink which uses
the HDMI CEC (Consumer Electronics Control)
protocol. You can use one single remote control
to control all EasyLink-compliant devices that are
connected through HDMI connectors.
[Menu Language]
Select an on-screen menu language.
Note
•
•
[On] - Turn on EasyLink features.
[Off] - Disable EasyLink features.
• If this player is connected to an HDMI CEC compliant
TV, and you select [Auto] for the [Menu Language],
it switches automatically to the same menu display
language as per your TV setting.
[One Touch Play]
When you press (standby) to turn on this
player, the TV (if the TV supports one-touch play)
[Audio]
automatically turns on and switches to the video-in
channel. Disc play starts if there is a disc in this
player.
Select an audio language for disc play.
[Subtitle]
Select a subtitle language for disc play.
[Disc Menu]
•
•
[On] - Turn on one-touch play feature.
[Off] - Disable one-touch play feature.
Select a language for disc menu.
[One Touch Standby]
When you press and hold (standby), all the
connected HDMI CEC devices (if the device
supports one-touch standby) switch to standby
mode simultaneously.
Note
• If the language you have set is not available on the disc,
the disc uses its own default language.
• For some discs, the subtitle/audio language can only be
•
•
[On] - Turn on one-touch standby feature.
changed from the disc menu.
[Off] - Disable one-touch standby feature.
[Parental Control]
Note
Restrict access to discs that are unsuitable for
children. These types of discs must be recorded
with ratings.
• You must turn on the HDMI CEC operations on the
TV/devices before you can enjoy the EasyLink controls.
See the TV/devices manual for details.
To access, enter your last set password or ‘0000’.
• Philips does not guarantee 100% interoperability with all
HDMI CEC compliant devices.
Note
• Rated discs above the level you set in [Parental Control]
require a password to be played.
• The ratings are country-dependent. To allow all discs to
play, select ‘8’ for DVD-video and BD-Video.
• Some discs have ratings printed on them but are not
recorded with ratings. This function has no effect on
such discs.
Preference setup
1
2
3
Press
.
Select [Setup], and press OK.
Select [Preference], and press
.
24 EN
[Screen Saver]
Turn on or off the screen saver mode. It helps to
protect the TV screen from being damaged due to
over exposure to static image for being too long.
•
[On] - Set the screen saver active after
10 minutes of inactivity (for example, in the
pause or stop mode)
•
[Off] - Disable screen saver mode.
[Auto Subtitle Shift]
Turn on or off the automatic subtitle shift.
•
[On] - The subtitle position on the TV screen
is automatically adjusted.
[Off] - Disable the automatically subtitle shift.
•
4
5
Select an option, and press OK.
Select a setting, and press OK.
[Change Password]
Set or change the password.
•
•
To return to the previous menu, press
.
To exit the menu, press
.
1) Press the Numeric buttons to enter the
password or your last set password. If you forget
the password, enter ‘0000’, then press OK.
2) Enter the new password.
3) Enter the same password again.
4) Move to [Confirm] in the menu and press OK.
[BD-Live Security]
You can restrict internet access for BD-Live bonus
contents which are available to certain Blu-ray discs.
•
[On] - Internet access is prohibited for all
BD-Live contents.
[Off] - Internet access is permitted for all
BD-Live contents.
•
[Display Panel]
[Software Update]
Select a brightness level of the front panel display.
Update the software of this player (if a latest
version is available on Philips website) to enhance
the performance of this player.
•
•
[Normal] - Normal brightness.
[Dim] - To dim display.
[Auto Standby]
Turn on or off auto standby mode. It is an energy
saving feature.
•
[USB] - Update software from the USB device
which is connected to this player.
[Network] - Update software from the
internet.
•
•
[On] - Switch to standby after 30 minutes
of inactivity (for example, in pause or stop
mode).
Note
•
[Off] - Disable auto standby mode.
[VCD PBC]
• For detailed software updating, see “Additional
information” > “Update software”.
Turn on or off the content menu of VCDs/SVCDs
with PBC (playback control) feature.
•
[On] - Display the index menu when you load
a disc for play.
[Off] - Skip the menu and start play from the
first title.
[Clear Memory]
If the internal memory of this player is not enough
to download BD-Live bonus contents for a BD disc,
reformat the local storage to clear all the contents.
•
Advanced setup
Note
1
2
3
Press
.
• When you clear the local storage, previous download of
BD-Live bonus contents is no longer available.
Select [Setup], and press OK.
Select [Advanced], and press
.
[Local Storage]
Select a location for downloaded BD-Live data to
be saved.
•
[Internal] - Save the download on the internal
memory of this player.
[External] - Save the download on the
connected USB flash drive.
•
EN 25
[DivX® VOD Code]
7 Additional Information
Update software
For software updates to enchance performance,
check the current software version of this player to
compare with the latest software (if available) at the
Philips website.
Obtain the DivX® registration code or the
deregistration code.
Tip
• Use this player’s DivX registration code when you rent
videos rented or purchased through the DivX® VOD
(Video On Demand) service can be played only on the
device to which it is registered.
1
2
3
Press
.
Select [Setup], and press OK.
Select [Advanced] > [Version Info.], and press
OK.
[Version Info.]
Display the software version.
Update software via network
Tip
1
Set up the Internet connection (see “Get
started’ > “Set up a network”).
• This information is needed for you to check if a latest
software version is available at the Philips website so that
you can download and install on this player.
2
In the Home menu, select [Setup] >
[Advanced] > [Software Update] > [Network].
[Restore Default Settings]
Reset all the settings of this player to the factory
settings, except for [Parental Control] setting.
»
You are prompted to start upgrading
process if upgrade media is detected.
3
Follow the instructions on the TV screen to
confirm update operation.
»
When the software update is complete, the
player automatically turns off and on again.
Update software via USB
1
the latest software version is available for this
player.
2
Download the software into a USB flash drive:
a
Un-zip the download, and make sure that
the un-zipped folder is named “UPG_
ALL”.
b
Put the “UPG_ALL” folder in the root
directory.
3
4
5
Insert the USB flash drive to the
(USB)
jack on this player.
In the Home menu, select [Setup] >
[Advanced] > [Software Update] > [USB].
Follow the instructions on the TV screen to
confirm update operation.
»
When the software update is complete, the
player automatically turns off and on again.
Note
• Do not turn off the power or remove the USB flash
drive when software updating is in progress to prevent
possible damage of this player.
26 EN
Accessories supplied
Care
•
•
•
•
Remote control and batteries
Power cable
Quick start guide
User manual
Caution
• Never use solvents such as benzene, thinner, cleaners
available commercially, or anti-static sprays intended
for discs.
Laser Specification
•
•
•
Laser Type:
•
•
•
BD Laser Diode: AlGaInN
DVD Laser Diode: AlGaInP
CD Laser Diode: AlGaInP
Clean discs
Wipe the disc with a micro fibre cleaning cloth from
the centre to the edge in a straight line movement.
Wave length:
•
•
•
BD: 405 +5nm/-5nm
DVD: 655 +10nm/-10nm
CD: 790 +10nm/-20nm
Specifications
Output power:
•
•
•
BD: Max. ratings: 20mW
Note
DVD: Max. ratings: 6mW
CD: Max. ratings: 7mW
• Specifications are subject to change without notice
Video
•
•
•
Signal system: PAL / NTSC
Composite video output: 1 Vp-p (75 ohm)
Component video output: 480/576i, 480/576p,
720p, 1080i
•
•
•
Y: 1 Vp-p (75 ohm)
Pb: 0.7 V-pp (75 ohm)
Pr: 0.7 V-pp (75 ohm)
•
HDMI output 480p, 576p, 720p, 1080i, 1080p,
1080p24
Audio
•
2 Channel analog output
•
•
•
•
Audio Front L + R : 2 Vrms (> 1 kohm)
Signal to noise ratio: > 120 dB
Dynamic Range (1kHz): > 100 dB
Total harmonic distortion: < 90 dB
•
7.1 Channel analog output
•
•
•
•
•
Audio Front L + R : 2 Vrms (> 1 kohm)
Audio Surrond L + R : 2 Vrms (> 1 kohm)
Audio Center : 2 Vrms (> 1 kohm)
Audio Subwoofer : 1.15 Vrms (> 1 kohm)
Audio Rear L + R: 2 Vrms (> 1 kohm)
•
Digital output: 0.5 Vp-p (75 ohm)
•
Optical, Coaxial
•
HDMI output
USB
•
•
Compatibility: Hi-Speed USB (2.0)
Class support: UMS (USB Mass Storage Class)
Main unit
•
•
•
•
•
Power supply rating: AC 220-230V~, 50 Hz
Power consumption: 30 W
Power consumption in standby mode: < 0.2 W
Dimensions (w x h x d): 435 x 70 x 260 (mm)
Net Weight: 5.0 kg
EN 27
Sound
8 Troubleshooting
No audio output from the TV.
•
•
Ensure that the audio cables are connected to
the audio input of the TV.
Assign the audio input of the TV to the
corresponding video input. See the TV user
manual for details.
Warning
• Risk of electric shock. Never remove the casing of the
player.
No audio output from the loudspeakers of the
audio device (home theater /amplifier/receiver).
•
To keep the warranty valid, never try to repair the
player yourself.
If you have problems using this player, check the
following points before you request service. If you still
have a problem, register your player and get support
Ensure that the audio cables are connected to
the audio input of the audio device.
Turn on the audio device to its correct audio
input source.
•
No 7.1 - channel audio from the loudspeaker of
the audio system.
•
•
•
Main unit
No reaction to the remote control.
Ensure that the disc contains 7.1 - channel
audio.
Ensure that the audio device supports 7.1 -
channel audio.
Ensure that the audio format is supported
by the disc and the connected audio device
(amplifier/receiver).
•
•
Connect this player to the power outlet.
Point the remote control at the IR sensor
located on the front panel of this player.
Insert the batteries correctly.
•
•
Insert new batteries in the remote control.
No sound on HDMI connection.
•
Picture
No picture.
You may not hear any sound from the HDMI
output if the connected device is non-HDCP
compliant or only DVI-compatible.
•
See TV manual for correct video input
No secondary audio output for Picture-in-Picture
feature.
•
selection. Change the TV channel until you see
the Philips screen.
When [Bitstream] under the [HDMI Audio]
or [Digital Audio] menu is selected, interactive
sound like secondary sound for Picture-in-
Picture feature is muted. Deselect [Bitstream].
No picture on HDMI connection.
•
If this player is connected to an unauthorized
display device with an HDMI cable, the audio/
video signal may not be output.
•
•
Check if the HDMI cable is faulty. Replace a
new HDMI cable.
Play
Disc cannot be played.
On the remote control, press and then
press “731” (numeric buttons) to recover
picture display.
•
•
Ensure that the disc is correctly loaded.
Ensure that this player supports the disc. See
“Your Blu-ray disc player” > “Playable media”.
Ensure that this player supports the region
code of the DVD or BD.
For DVD RW or DVD R, ensure that the
disc is finalized.
Clean the disc.
No high-definition video signal on the TV.
•
•
•
•
Make sure that the disc contains high-definition
video.
•
Make sure that the TV supports high-definition
video.
Blu-ray 3D effect is not seen on the TV.
Data files (JPEG, MP3, WMA) cannot be played
or read.
•
3D option on this player is turned off. Enable
3D output (see “Adjust settings” > “Video
setup” > [Blu-ray 3D video]).
•
•
•
Ensure that the data file was recorded in the
UDF, ISO9660 or JOLIET format.
Ensure that the disc does not contain more
than 9,999 files for DVD, and 999 files for CD.
Ensure that the JPEG file extension is.jpg, .JPG,
.jpeg or .JPEG.
•
•
Ensure that the disc title being played is Blu-ray
3D compliant.
Ensure that the TV is 3D and HDMI compliant,
and the TV is set to 3D mode (refer to the
TV’s user manual).
•
Ensure that the 3D glasses are activated (refer
to the TV’s user manual).
28 EN
•
Ensure that the MP3/WMA file extension
is .mp3 or .MP3, and .wma or .WMA for
windows Media™ Audio.
9 Glossary
DivX video files cannot be played.
A
•
•
Ensure that the DivX video file is complete.
Ensure that the file name extension is correct.
Aspect ratio
Aspect ratio refers to the width to height ratio of
TV screens. The ratio of a standard TV is 4:3, while
the ratio of a high-definition or wide TV is 16:9.
The letter box allows you to enjoy a picture with a
wider perspective on a standard 4:3 screen.
The contents of the USB flash drive cannot be read.
•
The USB flash drive format is not compatible
with this player.
•
Maximum size of memory supported is
160GB.
AVCHD
‘No entry’ or ‘x’ sign appears on theTV.
The operation is not possible.
EasyLink feature does not work.
AVCHD is a format (standard) for high definition
video cameras that can be used to record and play
high-resolution HD images.
•
•
Ensure that this player is connected to the
Philips brand EasyLink TV and the [EasyLink]
in the menu is set to [On].
B
Unable to access BD-Live feature.
•
Check the network connection or make sure
that the network has been set up (see “Get
started” > “Set up a network”).
To free space, delete downloaded BD-Live
data on the connected USB storage device
(see “Adjust settings” > “Advanced setup” >
[Clear Memory]).
Make sure that the BD disc supports BD-Live
feature.
Blu-ray Disc (BD)
Blu-ray Disc is a next generation optical video
disc capable of storing five times more data than
a conventional DVD. The large capacity makes it
possible to benefit from the features such as high-
definition videos, multichannel surround sound,
interactive menus and so on.
•
•
BONUSVIEW
BonusView, also known as “Profile 1.1”. In
addition to basic playback and interactive features,
BonusView players introduced after 31st October,
2007 enables users to enjoy ‘Picture-in-Picture’
(PiP) and secondary audio features (useful
when playing games that use additional audio
stream while the movie is playing) on compatible
BonusView discs.
Network
Wireless network is not found or distorted.
•
•
•
Microwave ovens, Dect phones or other
wireless devices in your neighborhood might
disturb the wireless network.
Make sure that the firewalls in your network
allow access to the wireless connection of this
player.
If the wireless network does not work
properly in your home, try the wired network
connection (see “Get started” > “Set up a
network”).
D
Digital Audio
Digital Audio is a sound signal that has been
converted into numerical values. Digital sound
can be transmitted through multiple channels.
Analogue sound can only be transmitted through
two channels.
Net TV does not work.
•
Check the router connection (refer to the user
manual for the router).
Browse PC and Net TV work slowly.
•
Look in your wireless router’s user manual for
information on indoor range, transfer rate and
other factors of signal quality.
You need a high speed Internet connection for
your router.
DivX Video-On-Demand
This DivX Certified ® device must be registered
in order to play DivX Video-on-Demand (VOD)
content. To generate the registration code, locate
the DivX VOD section in your device setup menu.
Go to vod.divx.com with this code to complete the
registration process and learn more about DivX
video.
•
EN 29
Dolby Digital
M
A surround sound system developed by Dolby
Laboratories that contains up to six channels of
digital audio (front left and right, surround left and
right, center and subwoofer.)
MP3
A file format with a sound data compression
system. MP3 is the abbreviation of Motion Picture
Experts Group 1 (or MPEG-1) Audio Layer 3. With
the MP3 format, one CD-R or CD-RW can contain
about 10 times more data than a regular CD.
DTS
Digital Theatre Systems. A surround sound system
for providing 5.1 channels of discrete digital audio
in consumer electronics products and software
content. It is not developed by Dolby Digital.
P
PBC
H
Playback Control. A system where you navigate
through a Video CD/Super VCD with on-screen
menus that are recorded onto the disc. You can
enjoy interactive playback and search.
HDCP
High-bandwidth Digital Content Protection. This is
a specification that provides a secure transmission
of digital contents between different devices (to
prevent unauthorized copyright.)
PCM
Pulse Code Modulation. A digital audio encoding
system.
HDMI
High-Definition Multimedia Interface (HDMI) is
a high-speed digital interface that can transmit
uncompressed high definition video and digital
multichannel audio. It delivers high quality picture
and sound quality, completely free from noise.
HDMI is fully backward-compatible with DVI.
As required by the HDMI standard, connecting to
HDMI or DVI products without HDCP (High-
bandwidth Digital Content Protection) will result in
no Video or Audio output.
R
Region code
A system that allows discs to be played only in the
region designated. This unit only plays discs that
have compatible region codes. You can find the
region code of your unit on the product label. Some
discs are compatible with more than one region (or
ALL regions.)
J
W
JPEG
WMA
A very common digital still picture format. A still-
picture data compression system proposed by the
Joint Photographic Expert Group, which features
small decrease in image quality in spite of its high
compression ratio. Files are recognized by their file
extension ‘.jpg’ or ‘.jpeg.’
Windows Media™ Audio. Refers to an audio
compression technology developed by Microsoft
Corporation. WMA data can be encoded with
Windows Media player version 9 or Windows
Media player for Windows XP. Files are recognized
by their file extension ‘.wma.’
L
LAN (Local Area Network)
A group of linked devices in a company, school
or home. Indicates the boundaries of a particular
network.
Local storage
This storage area is used as destination for storing
additional contents from BD-Live enabled BD-
Video.
30 EN
LicenseTexts and Acknowledgements for any open source software used in
this Philips product
Instructions to obtain source code for this software can be found in the user manual.
1. U-boot
#
# (C) Copyright 2000 - 2008
# Wolfgang Denk, DENX Software Engineering, [email protected].
#
# See file CREDITS for list of people who contributed to this
# project.
#
# This program is free software; you can redistribute it and/or
# modify it under the terms of the GNU General Public License as
# published by the Free Software Foundation; either version 2 of
# the License, or (at your option) any later version.
#
# This program is distributed in the hope that it will be useful,
# but WITHOUT ANY WARRANTY; without even the implied warranty of
# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
# GNU General Public License for more details.
#
# You should have received a copy of the GNU General Public License
# along with this program; if not, write to the Free Software
# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
# MA 02111-1307 USA
#
A copy of the GPL is included below at item 2.
2. Linux kernel
NOTE! This copyright does *not* cover user programs that use kernel services by normal system calls - this is
merely considered normal use of the kernel, and does *not* fall under the heading of “derived work”.
Also note that the GPL below is copyrighted by the Free Software Foundation, but the instance of code that it
refers to (the linux kernel) is copyrighted by me and others who actually wrote it.
Also note that the only valid version of the GPL as far as the kernel is concerned is _this_ particular version of
the license (ie v2, not v2.2 or v3.x or whatever), unless explicitly otherwise stated.
Linus Torvalds
----------------------------------------
GNU GENERAL PUBLIC LICENSE
Version 2, June 1991
Copyright (C) 1989, 1991 Free Software Foundation, Inc.
675 Mass Ave, Cambridge, MA 02139, USA
Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not
allowed.
Preamble
The licenses for most software are designed to take away your freedom to share and change it. By contrast,
the GNU General Public License is intended to guarantee your freedom to share and change free software--to
make sure the software is free for all its users. This General Public License applies to most of the Free Software
Foundation’s software and to any other program whose authors commit to using it. (Some other Free Software
Foundation software is covered by the GNU Library General Public License instead.) You can apply it to your
programs, too.
When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are
designed to make sure that you have the freedom to distribute copies of free software (and charge for this
service if you wish), that you receive source code or can get it if you want it, that you can change the software or
use pieces of it in new free programs; and that you know you can do these things.
1
To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask you
to surrender the rights. These restrictions translate to certain responsibilities for you if you distribute copies of
the software, or if you modify it.
For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the recipients
all the rights that you have. You must make sure that they, too, receive or can get the source code. And you
must show them these terms so they know their rights.
We protect your rights with two steps: (1) copyright the software, and (2) offer you this license which gives you
legal permission to copy, distribute and/or modify the software.
Also, for each author’s protection and ours, we want to make certain that everyone understands that there
is no warranty for this free software. If the software is modified by someone else and passed on, we want its
recipients to know that what they have is not the original, so that any problems introduced by others will not
reflect on the original authors’ reputations.
Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that
redistributors of a free program will individually obtain patent licenses, in effect making the program proprietary.
To prevent this, we have made it clear that any patent must be licensed for everyone’s free use or not licensed at
all.
The precise terms and conditions for copying, distribution and modification follow.
GNU GENERAL PUBLIC LICENSE
TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION
0. This License applies to any program or other work which contains a notice placed by the copyright holder
saying it may be distributed under the terms of this General Public License. The “Program”, below, refers to
any such program or work, and a “work based on the Program” means either the Program or any derivative
work under copyright law: that is to say, a work containing the Program or a portion of it, either verbatim
or with modifications and/or translated into another language. (Hereinafter, translation is included without
limitation in the term “modification”.) Each licensee is addressed as “you”.
Activities other than copying, distribution and modification are not covered by this License; they are outside
its scope. The act of running the Program is not restricted, and the output from the Program is covered only
if its contents constitute a work based on the Program (independent of having been made by running the
Program). Whether that is true depends on what the Program does.
1. You may copy and distribute verbatim copies of the Program’s source code as you receive it, in any medium,
provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice
and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any
warranty; and give any other recipients of the Program a copy of this License along with the Program.
You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty
protection in exchange for a fee.
2. You may modify your copy or copies of the Program or any portion of it, thus forming a work based on the
Program, and copy and distribute such modifications or work under the terms of Section 1 above, provided that
you also meet all of these conditions:
a) You must cause the modified files to carry prominent notices stating that you changed the files and the
date of any change.
b) You must cause any work that you distribute or publish, that in whole or in part contains or is derived
from the Program or any part thereof, to be licensed as a whole at no charge to all third parties under
the terms of this License.
c) If the modified program normally reads commands interactively when run, you must cause it, when
started running for such interactive use in the most ordinary way, to print or display an announcement
including an appropriate copyright notice and a notice that there is no warranty (or else, saying that you
provide a warranty) and that users may redistribute the program under these conditions, and telling
the user how to view a copy of this License. (Exception: if the Program itself is interactive but does not
normally print such an announcement, your work based on the Program is not required to print an
announcement.)
These requirements apply to the modified work as a whole. If identifiable sections of that work are
not derived from the Program, and can be reasonably considered independent and separate works in
themselves, then this License, and its terms, do not apply to those sections when you distribute them as
separate works. But when you distribute the same sections as part of a whole which is a work based on the
Program, the distribution of the whole must be on the terms of this License, whose permissions for other
licensees extend to the entire whole, and thus to each and every part regardless of who wrote it.
2
Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you;
rather, the intent is to exercise the right to control the distribution of derivative or collective works based
on the Program.
In addition, mere aggregation of another work not based on the Program with the Program (or with a work
based on the Program) on a volume of a storage or distribution medium does not bring the other work
under the scope of this License.
3. You may copy and distribute the Program (or a work based on it, under Section 2) in object code or
executable form under the terms of Sections 1 and 2 above provided that you also do one of the following:
a) Accompany it with the complete corresponding machine-readable source code, which must be
distributed under the terms of Sections 1 and 2 above on a medium customarily used for software
interchange; or,
b) Accompany it with a written offer, valid for at least three years, to give any third party, for a charge no
more than your cost of physically performing source distribution, a complete machine-readable copy
of the corresponding source code, to be distributed under the terms of Sections 1 and 2 above on a
medium customarily used for software interchange; or,
c) Accompany it with the information you received as to the offer to distribute corresponding source
code. (This alternative is allowed only for noncommercial distribution and only if you received the
program in object code or executable form with such an offer, in accord with Subsection b above.)
The source code for a work means the preferred form of the work for making modifications to it. For an
executable work, complete source code means all the source code for all modules it contains, plus any
associated interface definition files, plus the scripts used to control compilation and installation of the
executable. However, as a special exception, the source code distributed need not include anything that is
normally distributed (in either source or binary form) with the major components (compiler, kernel, and so
on) of the operating system on which the executable runs, unless that component itself accompanies the
executable.
If distribution of executable or object code is made by offering access to copy from a designated place, then
offering equivalent access to copy the source code from the same place counts as distribution of the source
code, even though third parties are not compelled to copy the source along with the object code.
4. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this
License. Any attempt otherwise to copy, modify, sublicense or distribute the Program is void, and will
automatically terminate your rights under this License. However, parties who have received copies, or rights,
from you under this License will not have their licenses terminated so long as such parties remain in full
compliance.
5. You are not required to accept this License, since you have not signed it. However, nothing else grants you
permission to modify or distribute the Program or its derivative works. These actions are prohibited by law if
you do not accept this License. Therefore, by modifying or distributing the Program (or any work based on the
Program), you indicate your acceptance of this License to do so, and all its terms and conditions for copying,
distributing or modifying the Program or works based on it.
6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically
receives a license from the original licensor to copy, distribute or modify the Program subject to these terms
and conditions. You may not impose any further restrictions on the recipients’ exercise of the rights granted
herein. You are not responsible for enforcing compliance by third parties to this License.
7. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not
limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise)
that contradict the conditions of this License, they do not excuse you from the conditions of this License.
If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other
pertinent obligations, then as a consequence you may not distribute the Program at all. For example, if a
patent license would not permit royalty-free redistribution of the Program by all those who receive copies
directly or indirectly through you, then the only way you could satisfy both it and this License would be to
refrain entirely from distribution of the Program.
If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance
of the section is intended to apply and the section as a whole is intended to apply in other circumstances.
It is not the purpose of this section to induce you to infringe any patents or other property right claims or
to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the
free software distribution system, which is implemented by public license practices. Many people have
made generous contributions to the wide range of software distributed through that system in reliance on
consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute
software through any other system and a licensee cannot impose that choice.
3
This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this
License.
8. If the distribution and/or use of the Program is restricted in certain countries either by patents or by
copyrighted interfaces, the original copyright holder who places the Program under this License may add an
explicit geographical distribution limitation excluding those countries, so that distribution is permitted only
in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in
the body of this License.
9. The Free Software Foundation may publish revised and/or new versions of the General Public License from
time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to
address new problems or concerns.
Each version is given a distinguishing version number. If the Program specifies a version number of this
License which applies to it and “any later version”, you have the option of following the terms and conditions
either of that version or of any later version published by the Free Software Foundation. If the Program
does not specify a version number of this License, you may choose any version ever published by the Free
Software Foundation.
10. If you wish to incorporate parts of the Program into other free programs whose distribution conditions are
different, write to the author to ask for permission. For software which is copyrighted by the Free Software
Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision
will be guided by the two goals of preserving the free status of all derivatives of our free software and of
promoting the sharing and reuse of software generally.
NO WARRANTY
11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE
PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE
STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE
PROGRAM “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND
PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE,
YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.
12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY
COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE
PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL,
SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY
TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING
RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF
THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER
PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
END OF TERMS AND CONDITIONS
Appendix: How to Apply These Terms to Your New Programs
If you develop a new program, and you want it to be of the greatest possible use to the public, the best way to
achieve this is to make it free software which everyone can redistribute and change under these terms.
To do so, attach the following notices to the program. It is safest to attach them to the start of each source file
to most effectively convey the exclusion of warranty; and each file should have at least the “copyright” line and a
pointer to where the full notice is found.
<one line to give the program’s name and a brief idea of what it does.>
Copyright (C) 19yy <name of author>
This program is free software; you can redistribute it and/or modify it under the terms of the GNU General
Public License as published by the Free Software Foundation; either version 2 of the License, or (at your option)
any later version.
This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even
the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
General Public License for more details.
You should have received a copy of the GNU General Public License along with this program; if not, write to the
Free Software Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
Also add information on how to contact you by electronic and paper mail.
4
If the program is interactive, make it output a short notice like this when it starts in an interactive mode:
Gnomovision version 69, Copyright (C) 19yy name of author
Gnomovision comes with ABSOLUTELY NO WARRANTY; for details type `show w’.
This is free software, and you are welcome to redistribute it under certain conditions; type `show c’ for
details.
The hypothetical commands `show w’ and `show c’ should show the appropriate parts of the General Public
License. Of course, the commands you use may be called something other than `show w’ and `show c’; they
could even be mouse-clicks or menu items--whatever suits your program.
You should also get your employer (if you work as a programmer) or your school, if any, to sign a “copyright
disclaimer” for the program, if necessary. Here is a sample; alter the names:
Yoyodyne, Inc., hereby disclaims all copyright interest in the program `Gnomovision’ (which makes passes at
compilers) written by James Hacker.
<signature of Ty Coon>, 1 April 1989
Ty Coon, President of Vice
This General Public License does not permit incorporating your program into proprietary programs. If your
program is a subroutine library, you may consider it more useful to permit linking proprietary applications with
the library. If this is what you want to do, use the GNU Library General Public License instead of this License.
3. Busybox, the Linux IR control package and SquashFS
Busybox, the Linux IR control package and SquashFS are subject to the GPL, a copy of which is included at item 2.
4. DirectFB, glibc, libusb-compat, libusb, e2fsprogs and mtd-utils
DirectFB glibc, libmtp, libusb and e2fsprogs are subject to the following license:
GNU LESSER GENERAL PUBLIC LICENSE
Version 2.1, February 1999
Copyright (C) 1991, 1999 Free Software Foundation, Inc.
59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not
allowed.
[This is the first released version of the Lesser GPL. It also counts as the successor of the GNU Library Public
License, version 2, hence the version number 2.1.]
Preamble
The licenses for most software are designed to take away your freedom to share and change it. By contrast, the
GNU General Public Licenses are intended to guarantee your freedom to share and change free software--to
make sure the software is free for all its users.
This license, the Lesser General Public License, applies to some specially designated software packages--typically
libraries--of the Free Software Foundation and other authors who decide to use it. You can use it too, but we
suggest you first think carefully about whether this license or the ordinary General Public License is the better
strategy to use in any particular case, based on the explanations below.
When we speak of free software, we are referring to freedom of use, not price. Our General Public Licenses
are designed to make sure that you have the freedom to distribute copies of free software (and charge for this
service if you wish); that you receive source code or can get it if you want it; that you can change the software
and use pieces of it in new free programs; and that you are informed that you can do these things.
To protect your rights, we need to make restrictions that forbid distributors to deny you these rights or to ask
you to surrender these rights. These restrictions translate to certain responsibilities for you if you distribute
copies of the library or if you modify it.
For example, if you distribute copies of the library, whether gratis or for a fee, you must give the recipients all the
rights that we gave you. You must make sure that they, too, receive or can get the source code. If you link other
code with the library, you must provide complete object files to the recipients, so that they can relink them with
the library after making changes to the library and recompiling it. And you must show them these terms so they
know their rights.
We protect your rights with a two-step method: (1) we copyright the library, and (2) we offer you this license,
which gives you legal permission to copy, distribute and/or modify the library.
To protect each distributor, we want to make it very clear that there is no warranty for the free library. Also,
if the library is modified by someone else and passed on, the recipients should know that what they have is
5
not the original version, so that the original author’s reputation will not be affected by problems that might be
introduced by others.
Finally, software patents pose a constant threat to the existence of any free program. We wish to make sure that
a company cannot effectively restrict the users of a free program by obtaining a restrictive license from a patent
holder. Therefore, we insist that any patent license obtained for a version of the library must be consistent with
the full freedom of use specified in this license.
Most GNU software, including some libraries, is covered by the ordinary GNU General Public License. This
license, the GNU Lesser General Public License, applies to certain designated libraries, and is quite different
from the ordinary General Public License. We use this license for certain libraries in order to permit linking
those libraries into non-free programs.
When a program is linked with a library, whether statically or using a shared library, the combination of the two
is legally speaking a combined work, a derivative of the original library. The ordinary General Public License
therefore permits such linking only if the entire combination fits its criteria of freedom. The Lesser General
Public License permits more lax criteria for linking other code with the library.
We call this license the “Lesser” General Public License because it does Less to protect the user’s freedom than
the ordinary General Public License. It also provides other free software developers Less of an advantage over
competing non-free programs. These disadvantages are the reason we use the ordinary General Public License
for many libraries. However, the Lesser license provides advantages in certain special circumstances.
For example, on rare occasions, there may be a special need to encourage the widest possible use of a certain
library, so that it becomes a de-facto standard. To achieve this, non-free programs must be allowed to use the
library. A more frequent case is that a free library does the same job as widely used non-free libraries. In this
case, there is little to gain by limiting the free library to free software only, so we use the Lesser General Public
License.
In other cases, permission to use a particular library in non-free programs enables a greater number of people
to use a large body of free software. For example, permission to use the GNU C Library in non-free programs
enables many more people to use the whole GNU operating system, as well as its variant, the GNU/Linux
operating system.
Although the Lesser General Public License is Less protective of the users’ freedom, it does ensure that the user
of a program that is linked with the Library has the freedom and the wherewithal to run that program using a
modified version of the Library.
The precise terms and conditions for copying, distribution and modification follow. Pay close attention to the
difference between a “work based on the library” and a “work that uses the library”. The former contains code
derived from the library, whereas the latter must be combined with the library in order to run.
GNU LESSER GENERAL PUBLIC LICENSE
TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION
0. This License Agreement applies to any software library or other program which contains a notice placed by
the copyright holder or other authorized party saying it may be distributed under the terms of this Lesser
General Public License (also called “this License”).
Each licensee is addressed as “you”.
A “library” means a collection of software functions and/or data prepared so as to be conveniently linked
with application programs (which use some of those functions and data) to form executables.
The “Library”, below, refers to any such software library or work which has been distributed under these
terms. A “work based on the Library” means either the Library or any derivative work under copyright law:
that is to say, a work containing the Library or a portion of it, either verbatim or with modifications and/or
translated straightforwardly into another language. (Hereinafter, translation is included without limitation in
the term “modification”.)
“Source code” for a work means the preferred form of the work for making modifications to it. For a library,
complete source code means all the source code for all modules it contains, plus any associated interface
definition files, plus the scripts used to control compilation and installation of the library.
Activities other than copying, distribution and modification are not covered by this License; they are outside
its scope. The act of running a program using the Library is not restricted, and output from such a program
is covered only if its contents constitute a work based on the Library (independent of the use of the Library
in a tool for writing it). Whether that is true depends on what the Library does and what the program that
uses the Library does.
1. You may copy and distribute verbatim copies of the Library’s complete source code as you receive it, in any
medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright
6
notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of
any warranty; and distribute a copy of this License along with the Library.
You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty
protection in exchange for a fee.
2. You may modify your copy or copies of the Library or any portion of it, thus forming a work based on the
Library, and copy and distribute such modifications or work under the terms of Section 1 above, provided
that you also meet all of these conditions:
a) The modified work must itself be a software library.
b) You must cause the files modified to carry prominent notices stating that you changed the files and the
date of any change.
c) You must cause the whole of the work to be licensed at no charge to all third parties under the terms
of this License.
d) If a facility in the modified Library refers to a function or a table of data to be supplied by an application
program that uses the facility, other than as an argument passed when the facility is invoked, then you
must make a good faith effort to ensure that, in the event an application does not supply such function
or table, the facility still operates, and performs whatever part of its purpose remains meaningful.
(For example, a function in a library to compute square roots has a purpose that is entirely well-defined
independent of the application. Therefore, Subsection 2d requires that any application-supplied function
or table used by this function must be optional: if the application does not supply it, the square root
function must still compute square roots.)
These requirements apply to the modified work as a whole. If identifiable sections of that work are not
derived from the Library, and can be reasonably considered independent and separate works in themselves,
then this License, and its terms, do not apply to those sections when you distribute them as separate
works. But when you distribute the same sections as part of a whole which is a work based on the Library,
the distribution of the whole must be on the terms of this License, whose permissions for other licensees
extend to the entire whole, and thus to each and every part regardless of who wrote it.
Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you;
rather, the intent is to exercise the right to control the distribution of derivative or collective works based
on the Library.
In addition, mere aggregation of another work not based on the Library with the Library (or with a work
based on the Library) on a volume of a storage or distribution medium does not bring the other work under
the scope of this License.
3. You may opt to apply the terms of the ordinary GNU General Public License instead of this License to a
given copy of the Library. To do this, you must alter all the notices that refer to this License, so that they
refer to the ordinary GNU General Public License, version 2, instead of to this License. (If a newer version
than version 2 of the ordinary GNU General Public License has appeared, then you can specify that version
instead if you wish.) Do not make any other change in these notices.
Once this change is made in a given copy, it is irreversible for that copy, so the ordinary GNU General Public
License applies to all subsequent copies and derivative works made from that copy.
This option is useful when you wish to copy part of the code of the Library into a program that is not a
library.
4. You may copy and distribute the Library (or a portion or derivative of it, under Section 2) in object code
or executable form under the terms of Sections 1 and 2 above provided that you accompany it with the
complete corresponding machine-readable source code, which must be distributed under the terms of
Sections 1 and 2 above on a medium customarily used for software interchange.
If distribution of object code is made by offering access to copy from a designated place, then offering
equivalent access to copy the source code from the same place satisfies the requirement to distribute the
source code, even though third parties are not compelled to copy the source along with the object code.
5. A program that contains no derivative of any portion of the Library, but is designed to work with the Library
by being compiled or linked with it, is called a “work that uses the Library”. Such a work, in isolation, is not a
derivative work of the Library, and therefore falls outside the scope of this License.
However, linking a “work that uses the Library” with the Library creates an executable that is a derivative
of the Library (because it contains portions of the Library), rather than a “work that uses the library”. The
executable is therefore covered by this License.
Section 6 states terms for distribution of such executables.
When a “work that uses the Library” uses material from a header file that is part of the Library, the object
code for the work may be a derivative work of the Library even though the source code is not.
7
Whether this is true is especially significant if the work can be linked without the Library, or if the work is
itself a library. The threshold for this to be true is not precisely defined by law.
If such an object file uses only numerical parameters, data structure layouts and accessors, and small
macros and small inline functions (ten lines or less in length), then the use of the object file is unrestricted,
regardless of whether it is legally a derivative work. (Executables containing this object code plus portions of
the Library will still fall under Section 6.)
Otherwise, if the work is a derivative of the Library, you may distribute the object code for the work under
the terms of Section 6.
Any executables containing that work also fall under Section 6, whether or not they are linked directly with
the Library itself.
6. As an exception to the Sections above, you may also combine or link a “work that uses the Library” with the
Library to produce a work containing portions of the Library, and distribute that work under terms of your
choice, provided that the terms permit modification of the work for the customer’s own use and reverse
engineering for debugging such modifications.
You must give prominent notice with each copy of the work that the Library is used in it and that the Library
and its use are covered by this License. You must supply a copy of this License. If the work during execution
displays copyright notices, you must include the copyright notice for the Library among them, as well as a
reference directing the user to the copy of this License. Also, you must do one of these things:
a) Accompany the work with the complete corresponding machine-readable source code for the Library
including whatever changes were used in the work (which must be distributed under Sections 1 and 2
above); and, if the work is an executable linked with the Library, with the complete machine-readable
“work that uses the Library”, as object code and/or source code, so that the user can modify the Library
and then relink to produce a modified executable containing the modified Library. (It is understood
that the user who changes the contents of definitions files in the Library will not necessarily be able to
recompile the application to use the modified definitions.)
b) Use a suitable shared library mechanism for linking with the Library. A suitable mechanism is one that
(1) uses at run time a copy of the library already present on the user’s computer system, rather than
copying library functions into the executable, and (2) will operate properly with a modified version
of the library, if the user installs one, as long as the modified version is interface-compatible with the
version that the work was made with.
c) Accompany the work with a written offer, valid for at least three years, to give the same user the
materials specified in Subsection 6a, above, for a charge no more than the cost of performing this
distribution.
d) If distribution of the work is made by offering access to copy from a designated place, offer equivalent
access to copy the above specified materials from the same place.
e) Verify that the user has already received a copy of these materials or that you have already sent this user
a copy.
For an executable, the required form of the “work that uses the library” must include any data and utility
programs needed for reproducing the executable from it. However, as a special exception, the materials to
be distributed need not include anything that is normally distributed (in either source or binary form) with
the major components (compiler, kernel, and so on) of the operating system on which the executable runs,
unless that component itself accompanies the executable.
It may happen that this requirement contradicts the license restrictions of other proprietary libraries that do
not normally accompany the operating system. Such a contradiction means you cannot use both them and
the Library together in an executable that you distribute.
7. You may place library facilities that are a work based on the Library side-by-side in a single library together
with other library facilities not covered by this License, and distribute such a combined library, provided that
the separate distribution of the work based on the Library and of the other library facilities is otherwise
permitted, and provided that you do these two things:
a) Accompany the combined library with a copy of the same work based on the Library, uncombined with
any other library facilities. This must be distributed under the terms of the Sections above.
b) Give prominent notice with the combined library of the fact that part of it is a work based on the
Library, and explaining where to find the accompanying uncombined form of the same work.
8. You may not copy, modify, sublicense, link with, or distribute the Library except as expressly provided under
this License. Any attempt otherwise to copy, modify, sublicense, link with, or distribute the Library is void,
and will automatically terminate your rights under this License. However, parties who have received copies,
or rights, from you under this License will not have their licenses terminated so long as such parties remain
in full compliance.
8
9. You are not required to accept this License, since you have not signed it. However, nothing else grants you
permission to modify or distribute the Library or its derivative works. These actions are prohibited by law
if you do not accept this License. Therefore, by modifying or distributing the Library (or any work based
on the Library), you indicate your acceptance of this License to do so, and all its terms and conditions for
copying, distributing or modifying the Library or works based on it.
10. Each time you redistribute the Library (or any work based on the Library), the recipient automatically
receives a license from the original licensor to copy, distribute, link with or modify the Library subject to
these terms and conditions. You may not impose any further restrictions on the recipients’ exercise of the
rights granted herein.
You are not responsible for enforcing compliance by third parties with this License.
11. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not
limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise)
that contradict the conditions of this License, they do not excuse you from the conditions of this License.
If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other
pertinent obligations, then as a consequence you may not distribute the Library at all. For example, if a
patent license would not permit royalty-free redistribution of the Library by all those who receive copies
directly or indirectly through you, then the only way you could satisfy both it and this License would be to
refrain entirely from distribution of the Library.
If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance
of the section is intended to apply, and the section as a whole is intended to apply in other circumstances.
It is not the purpose of this section to induce you to infringe any patents or other property right claims
or to contest validity of any such claims; this section has the sole purpose of protecting the integrity of
the free software distribution system which is implemented by public license practices. Many people have
made generous contributions to the wide range of software distributed through that system in reliance on
consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute
software through any other system and a licensee cannot impose that choice.
This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this
License.
12. If the distribution and/or use of the Library is restricted in certain countries either by patents or by
copyrighted interfaces, the original copyright holder who places the Library under this License may add an
explicit geographical distribution limitation excluding those countries, so that distribution is permitted only
in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in
the body of this License.
13. The Free Software Foundation may publish revised and/or new versions of the Lesser General Public
License from time to time. Such new versions will be similar in spirit to the present version, but may differ in
detail to address new problems or concerns.
Each version is given a distinguishing version number. If the Library specifies a version number of this License
which applies to it and “any later version”, you have the option of following the terms and conditions either
of that version or of any later version published by the Free Software Foundation. If the Library does
not specify a license version number, you may choose any version ever published by the Free Software
Foundation.
14. If you wish to incorporate parts of the Library into other free programs whose distribution conditions are
incompatible with these, write to the author to ask for permission. For software which is copyrighted by
the Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for
this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free
software and of promoting the sharing and reuse of software generally.
NO WARRANTY
15. BECAUSE THE LIBRARY IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE
LIBRARY, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED
IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE LIBRARY “AS IS”
WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT
LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE LIBRARY IS WITH
YOU. SHOULD THE LIBRARY PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY
SERVICING, REPAIR OR CORRECTION.
16. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY
COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE
LIBRARY AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL,
SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY
9
TO USE THE LIBRARY (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING
RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF
THE LIBRARY TO OPERATE WITH ANY OTHER SOFTWARE), EVEN IF SUCH HOLDER OR OTHER
PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
END OF TERMS AND CONDITIONS
How to Apply These Terms to Your New Libraries
If you develop a new library, and you want it to be of the greatest possible use to the public, we recommend
making it free software that everyone can redistribute and change. You can do so by permitting redistribution
under these terms (or, alternatively, under the terms of the ordinary General Public License).
To apply these terms, attach the following notices to the library. It is safest to attach them to the start of each
source file to most effectively convey the exclusion of warranty; and each file should have at least the “copyright”
line and a pointer to where the full notice is found.
<one line to give the library’s name and a brief idea of what it does.>
Copyright (C) <year> <name of author>
This library is free software; you can redistribute it and/or modify it under the terms of the GNU Lesser General
Public License as published by the Free Software Foundation; either version 2.1 of the License, or (at your
option) any later version.
This library is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the
implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU Lesser
General Public License for more details.
You should have received a copy of the GNU Lesser General Public License along with this library; if not, write
to the Free Software Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
Also add information on how to contact you by electronic and paper mail.
You should also get your employer (if you work as a programmer) or your school, if any, to sign a “copyright
disclaimer” for the library, if necessary. Here is a sample; alter the names:
Yoyodyne, Inc., hereby disclaims all copyright interest in the library `Frob’ (a library for tweaking knobs) written
by James Random Hacker.
<signature of Ty Coon>, 1 April 1990
Ty Coon, President of Vice
That’s all there is to it!
5. IJG: JPEG software decoder
The authors make NO WARRANTY or representation, either express or implied, with respect to this software,
its quality, accuracy, merchantability, or fitness for a particular purpose. This software is provided “AS IS”, and
you, its user, assume the entire risk as to its quality and accuracy.
This software is copyright (C) 1991-1998, Thomas G. Lane.
All Rights Reserved except as specified below.
Permission is hereby granted to use, copy, modify, and distribute this software (or portions thereof) for any
purpose, without fee, subject to these conditions:
(1) If any part of the source code for this software is distributed, then this README file must be included, with
this copyright and no-warranty notice unaltered; and any additions, deletions, or changes to the original files
must be clearly indicated in accompanying documentation.
(2) If only executable code is distributed, then the accompanying documentation must state that “this software
is based in part on the work of the Independent JPEG Group”.
(3) Permission for use of this software is granted only if the user accepts full responsibility for any undesirable
consequences; the authors accept NO LIABILITY for damages of any kind.
6. WPA Supplicant
Copyright (c) 2003-2009, Jouni Malinen <j@w1.fi> and contributors
All Rights Reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that
the following conditions are met:
10
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the
following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the
following disclaimer in the documentation and/or other materials provided with the distribution.
3. Neither the name(s) of the above-listed copyright holder(s) nor the names of its contributors may be used
to endorse or promote products derived from this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS”
AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT,
INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY
OF SUCH DAMAGE.
7. Unicode Bidirectional Algorithm
For the general privacy policy governing access to this site, see the Unicode Privacy Policy. For trademark usage,
see the Unicode Consortium® Trademarks and Logo Policy.
Notice to End User: Terms of Use
Carefully read the following legal agreement (“Agreement”). Use or copying of the software and/or codes
provided with this agreement (The “Software”) constitutes your acceptance of these terms
Unicode Copyright.
Copyright © 1991-2009 Unicode, Inc. All rights reserved.
Certain documents and files on this website contain a legend indicating that “Modification is permitted.” Any
person is hereby authorized, without fee, to modify such documents and files to create derivative works
conforming to the Unicode® Standard, subject to Terms and Conditions herein.
Any person is hereby authorized, without fee, to view, use, reproduce, and distribute all documents and files
solely for informational purposes in the creation of products supporting the Unicode Standard, subject to the
Terms and Conditions herein.
Further specifications of rights and restrictions pertaining to the use of the particular set of data files known as
the “Unicode Character Database” can be found in Exhibit 1.
Each version of the Unicode Standard has further specifications of rights and restrictions of use. For the book
editions, these are found on the back of the title page. For the online edition, certain files (such as the PDF files
for book chapters and code charts) carry specific restrictions. All other files are covered under these general
Terms of Use. To request a permission to reproduce any part of the Unicode Standard, please contact the
Unicode Consortium.
No license is granted to “mirror” the Unicode website where a fee is charged for access to the “mirror” site.
Modification is not permitted with respect to this document. All copies of this document must be verbatim.
Restricted Rights Legend. Any technical data or software which is licensed to the United States of America, its
agencies and/or instrumentalities under this Agreement is commercial technical data or commercial computer
software developed exclusively at private expense as defined in FAR 2.101, or DFARS 252.227-7014 (June 1995),
as applicable. For technical data, use, duplication, or disclosure by the Government is subject to restrictions as
set forth in DFARS 202.227-7015 Technical Data, Commercial and Items (Nov 1995) and this Agreement. For
Software, in accordance with FAR 12-212 or DFARS 227-7202, as applicable, use, duplication or disclosure by the
Government is subject to the restrictions set forth in this Agreement.
Warranties and Disclaimers.
This publication and/or website may include technical or typographical errors or other inaccuracies . Changes
are periodically added to the information herein; these changes will be incorporated in new editions of
the publication and/or website. Unicode may make improvements and/or changes in the product(s) and/or
program(s) described in this publication and/or website at any time.
If this file has been purchased on magnetic or optical media from Unicode, Inc. the sole and exclusive remedy for
any claim will be exchange of the defective media within ninety (90) days of original purchase.
EXCEPT AS PROVIDED IN SECTION C.2, THIS PUBLICATION AND/OR SOFTWARE IS PROVIDED “AS IS”
WITHOUT WARRANTY OF ANY KIND EITHER EXPRESS, IMPLIED, OR STATUTORY, INCLUDING, BUT
NOT LIMITED TO, ANY WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE,
11
OR NON-INFRINGEMENT. UNICODE AND ITS LICENSORS ASSUME NO RESPONSIBILITY FOR ERRORS
OR OMISSIONS IN THIS PUBLICATION AND/OR SOFTWARE OR OTHER DOCUMENTS WHICH ARE
REFERENCED BY OR LINKED TO THIS PUBLICATION OR THE UNICODE WEBSITE.
Waiver of Damages. In no event shall Unicode or its licensors be liable for any special, incidental, indirect or
consequential damages of any kind, or any damages whatsoever, whether or not Unicode was advised of the
possibility of the damage, including, without limitation, those resulting from the following: loss of use, data or
profits, in connection with the use, modification or distribution of this information or its derivatives.
Trademarks.
Unicode and the Unicode logo are registered trademarks of Unicode, Inc.
This site contains product names and corporate names of other companies. All product names and company
names and logos mentioned herein are the trademarks or registered trademarks of their respective owners.
Other products and corporate names mentioned herein which are trademarks of a third party are used only for
explanation and for the owners’ benefit and with no intent to infringe.
Use of third party products or information referred to herein is at the user’s risk.
Miscellaneous.
Jurisdiction and Venue. This server is operated from a location in the State of California, United States of
America. Unicode makes no representation that the materials are appropriate for use in other locations. If you
access this server from other locations, you are responsible for compliance with local laws. This Agreement,
all use of this site and any claims and damages resulting from use of this site are governed solely by the laws of
the State of California without regard to any principles which would apply the laws of a different jurisdiction.
The user agrees that any disputes regarding this site shall be resolved solely in the courts located in Santa Clara
County, California. The user agrees said courts have personal jurisdiction and agree to waive any right to transfer
the dispute to any other forum.
Modification by Unicode Unicode shall have the right to modify this Agreement at any time by posting it to this
site. The user may not assign any part of this Agreement without Unicode’s prior written consent.
Taxes. The user agrees to pay any taxes arising from access to this website or use of the information herein,
except for those based on Unicode’s net income.
Severability. If any provision of this Agreement is declared invalid or unenforceable, the remaining provisions of
this Agreement shall remain in effect.
Entire Agreement. This Agreement constitutes the entire agreement between the parties.
--------------------------------------------------------------------------------
EXHIBIT 1
UNICODE, INC. LICENSE AGREEMENT - DATA FILES AND SOFTWARE
NOTICE TO USER: Carefully read the following legal agreement. BY DOWNLOADING, INSTALLING,
COPYING OR OTHERWISE USING UNICODE INC.’S DATA FILES (“DATA FILES”), AND/OR SOFTWARE
(“SOFTWARE”), YOU UNEQUIVOCALLY ACCEPT, AND AGREE TO BE BOUND BY, ALL OF THE TERMS
AND CONDITIONS OF THIS AGREEMENT. IF YOU DO NOT AGREE, DO NOT DOWNLOAD, INSTALL,
COPY, DISTRIBUTE OR USE THE DATA FILES OR SOFTWARE.
COPYRIGHT AND PERMISSION NOTICE
unicode.org/copyright.html.
Permission is hereby granted, free of charge, to any person obtaining a copy of the Unicode data files and any
associated documentation (the “Data Files”) or Unicode software and any associated documentation (the
“Software”) to deal in the Data Files or Software without restriction, including without limitation the rights
to use, copy, modify, merge, publish, distribute, and/or sell copies of the Data Files or Software, and to permit
persons to whom the Data Files or Software are furnished to do so, provided that (a) the above copyright
notice(s) and this permission notice appear with all copies of the Data Files or Software, (b) both the above
copyright notice(s) and this permission notice appear in associated documentation, and (c) there is clear notice
in each modified Data File or in the Software as well as in the documentation associated with the Data File(s) or
Software that the data or software has been modified.
THE DATA FILES AND SOFTWARE ARE PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND,
EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OF THIRD PARTY RIGHTS. IN
NO EVENT SHALL THE COPYRIGHT HOLDER OR HOLDERS INCLUDED IN THIS NOTICE BE LIABLE
FOR ANY CLAIM, OR ANY SPECIAL INDIRECT OR CONSEQUENTIAL DAMAGES, OR ANY DAMAGES
12
WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION OF
CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION
WITH THE USE OR PERFORMANCE OF THE DATA FILES OR SOFTWARE.
Except as contained in this notice, the name of a copyright holder shall not be used in advertising or otherwise
to promote the sale, use or other dealings in these Data Files or Software without prior written authorization of
the copyright holder.
--------------------------------------------------------------------------------
Unicode and the Unicode logo are trademarks of Unicode, Inc., and may be registered in some jurisdictions. All
other trademarks and registered trademarks mentioned herein are the property of their respective owners.
--------------------------------------------------------------------------------
8. OpenSSL.
Open SSL is an Open Source toolkit implementing the Secure Sockets Layer (SSL v2/v3) and Transport Layer
Security (TLS v1) protocols as well as a full-strength general purpose cryptography library.
The license conditions are copied below.
The OpenSSL toolkit stays under a dual license, i.e. both the conditions of the OpenSSL License and the original
SSLeay license apply to the toolkit.
See below for the actual license texts. Actually both licenses are BSD-style
Open Source licenses. In case of any license issues related to OpenSSL, please contact openssl-core@openssl.
org.
OpenSSL License
---------------
/* =====================================================
* Copyright (c) 1998-2008 The OpenSSL Project. All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* 1. Redistributions of source code must retain the above copyright
*
*
notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
*
*
*
*
notice, this list of conditions and the following disclaimer in
the documentation and/or other materials provided with the
distribution.
* 3. All advertising materials mentioning features or use of this
*
*
*
*
software must display the following acknowledgment:
“This product includes software developed by the OpenSSL Project
for use in the OpenSSL Toolkit. (http://www.openssl.org/)”
* 4. The names “OpenSSL Toolkit” and “OpenSSL Project” must not be used to
*
*
*
*
endorse or promote products derived from this software without
prior written permission. For written permission, please contact
* 5. Products derived from this software may not be called “OpenSSL”
*
*
*
nor may “OpenSSL” appear in their names without prior written
permission of the OpenSSL Project.
* 6. Redistributions of any form whatsoever must retain the following
*
*
*
*
acknowledgment:
“This product includes software developed by the OpenSSL Project
for use in the OpenSSL Toolkit (http://www.openssl.org/)”
* THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT ``AS IS’’ AND ANY
13
* EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
* PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE OpenSSL PROJECT OR
* ITS CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
* SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
* NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
* LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
* CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR
* OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
* EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
* ======================================================
*
* This product includes cryptographic software written by Eric Young
* ([email protected]). This product includes software written by Tim
* Hudson ([email protected]).
*
*/
Original SSLeay License
-----------------------
/* Copyright (C) 1995-1998 Eric Young ([email protected])
* All rights reserved.
*
* This package is an SSL implementation written
* by Eric Young ([email protected]).
* The implementation was written so as to conform with Netscapes SSL.
*
* This library is free for commercial and non-commercial use as long as
* the following conditions are aheared to. The following conditions
* apply to all code found in this distribution, be it the RC4, RSA,
* lhash, DES, etc., code; not just the SSL code. The SSL documentation
* included with this distribution is covered by the same copyright terms
* except that the holder is Tim Hudson ([email protected]).
*
* Copyright remains Eric Young’s, and as such any Copyright notices in
* the code are not to be removed.
* If this package is used in a product, Eric Young should be given attribution
* as the author of the parts of the library used.
* This can be in the form of a textual message at program startup or
* in documentation (online or textual) provided with the package.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the copyright
*
notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
*
*
notice, this list of conditions and the following disclaimer in the
documentation and/or other materials provided with the distribution.
* 3. All advertising materials mentioning features or use of this software
*
*
*
*
*
must display the following acknowledgement:
“This product includes cryptographic software written by
Eric Young ([email protected])”
The word ‘cryptographic’ can be left out if the rouines from the library
being used are not cryptographic related :-).
* 4. If you include any Windows specific code (or a derivative thereof) from
*
*
*
the apps directory (application code) you must include an acknowledgement:
“This product includes software written by Tim Hudson ([email protected])”
* THIS SOFTWARE IS PROVIDED BY ERIC YOUNG ``AS IS’’ AND ANY EXPRESS OR
* IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
14
* WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
* PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR
* CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
* SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
* NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
* CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
* STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
* ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
* OF THE POSSIBILITY OF SUCH DAMAGE.
*
* The licence and distribution terms for any publically available version or
* derivative of this code cannot be changed. i.e. this code cannot simply be
* copied and put under another distribution licence
* [including the GNU Public Licence.]
*/
9. Zlib general purpose compression library
/* zlib.h -- interface of the ‘zlib’ general purpose compression library version 1.2.3, July 18th, 2005
Copyright (C) 1995-2005 Jean-loup Gailly and Mark Adler
This software is provided ‘as-is’, without any express or implied warranty. In no event will the authors be held
liable for any damages arising from the use of this software.
Permission is granted to anyone to use this software for any purpose, including commercial applications, and to
alter it and redistribute it freely, subject to the following restrictions:
1. The origin of this software must not be misrepresented; you must not claim that you wrote the original
software. If you use this software in a product, an acknowledgment in the product documentation would be
appreciated but is not required.
2. Altered source versions must be plainly marked as such, and must not be misrepresented as being the
original software.
3. This notice may not be removed or altered from any source distribution.
*/
10. cURL
COPYRIGHT AND PERMISSION NOTICE
Copyright (c) 1996 - 2009, Daniel Stenberg, <[email protected]>.
All rights reserved.
Permission to use, copy, modify, and distribute this software for any purpose with or without fee is hereby
granted, provided that the above copyright notice and this permission notice appear in all copies.
THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED,
INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A
PARTICULAR PURPOSE AND NONINFRINGEMENT OF THIRD PARTY RIGHTS. IN NO EVENT SHALL
THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF
OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
Except as contained in this notice, the name of a copyright holder shall not be used in advertising or otherwise
to promote the sale, use or other dealings in this Software without prior written authorization of the copyright
holder.
11. Freetype, a Free, High-Quality, and Portable Font Engine
The software is based in part of the work of the FreeType Team.
Portions of the relevant license conditions are copied below.
15
The FreeType Project LICENSE
2006-Jan-27
Copyright 1996-2002, 2006 by David Turner, Robert Wilhelm, and Werner Lemberg
…
1. No Warranty
------------------
THE FREETYPE PROJECT IS PROVIDED `AS IS’ WITHOUT WARRANTY OF ANY KIND, EITHER
EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT WILL ANY OF THE AUTHORS OR
COPYRIGHT HOLDERS BE LIABLE FOR ANY DAMAGES CAUSED BY THE USE OR THE INABILITY TO
USE, OF THE FREETYPE PROJECT.
2. Redistribution
-------------------
This license grants a worldwide, royalty-free, perpetual and irrevocable right and license to use, execute,
perform, compile, display, copy, create derivative works of, distribute and sublicense the FreeType Project (in
both source and object code forms) and derivative works thereof for any purpose; and to authorize others to
exercise some or all of the rights granted herein, subject to the following conditions:
…
o Redistribution in binary form must provide a disclaimer that states that the software is based in part of
the work of the FreeType Team, in the distribution documentation. We also encourage you to put an
URL to the FreeType web page in your documentation, though this isn’t mandatory.
…
12. International Components for Unicode
COPYRIGHT AND PERMISSION NOTICE
Copyright (c) 1995-2009 International Business Machines Corporation and others
All rights reserved.
Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated
documentation files (the “Software”), to deal in the Software without restriction, including without limitation the
rights to use, copy, modify, merge, publish, distribute, and/or sell copies of the Software, and to permit persons
to whom the Software is furnished to do so, provided that the above copyright notice(s) and this permission
notice appear in all copies of the Software and that both the above copyright notice(s) and this permission notice
appear in supporting documentation.
THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED,
INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A
PARTICULAR PURPOSE AND NONINFRINGEMENT OF THIRD PARTY RIGHTS. IN NO EVENT SHALL
THE COPYRIGHT HOLDER OR HOLDERS INCLUDED IN THIS NOTICE BE LIABLE FOR ANY CLAIM,
OR ANY SPECIAL INDIRECT OR CONSEQUENTIAL DAMAGES, OR ANY DAMAGES WHATSOEVER
RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION OF CONTRACT,
NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE
OR PERFORMANCE OF THIS SOFTWARE.
Except as contained in this notice, the name of a copyright holder shall not be used in advertising or otherwise
to promote the sale, use or other dealings in this Software without prior written authorization of the copyright
holder.
13. Expat
Copyright (c) 1998, 1999, 2000 Thai Open Source Software Center Ltd and Clark Cooper
Copyright (c) 2001, 2002, 2003, 2004, 2005, 2006 Expat maintainers.
Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated
documentation files (the “Software”), to deal in the Software without restriction, including without limitation
the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the Software, and to
permit persons to whom the Software is furnished to do so, subject to the following conditions:
The above copyright notice and this permission notice shall be included in all copies or substantial portions of
the Software.
16
THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED,
INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A
PARTICULAR PURPOSE AND NONINFRINGEMENT.
IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM,
DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE,
ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER
DEALINGS IN THE SOFTWARE.
14. DNS Resolver
The DNS resolver code, taken from BIND 4.9.5, is copyrighted both by UC Berkeley and by Digital Equipment
Corporation. The DEC portions are under the following license:
Portions Copyright (C) 1993 by Digital Equipment Corporation.
Permission to use, copy, modify, and distribute this software for any purpose with or without fee is hereby
granted, provided that the above copyright notice and this permission notice appear in all copies, and that the
name of Digital Equipment Corporation not be used in advertising or publicity pertaining to distribution of the
document or software without specific, written prior permission.
THE SOFTWARE IS PROVIDED ``AS IS’’ AND DIGITAL EQUIPMENT CORP. DISCLAIMS ALL WARRANTIES
WITH REGARD TO THIS SOFTWARE, INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS. IN NO EVENT SHALL DIGITAL EQUIPMENT CORPORATION BE LIABLE FOR ANY
SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER
RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION OF CONTRACT,
NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE
OR PERFORMANCE OF THIS SOFTWARE.
15. getnameinfo, getaddrinfo
The files inet/getnameinfo.c and sysdeps/posix/getaddrinfo.c are copyright (C) by Craig Metz and are distributed
under the following license:
/* The Inner Net License, Version 2.00
The author(s) grant permission for redistribution and use in source and binary forms, with or without
modification, of the software and documentation provided that the following conditions are met:
0. If you receive a version of the software that is specifically labelled as not being for redistribution (check the
version message and/or README), you are not permitted to redistribute that version of the software in any
way or form.
1. All terms of the all other applicable copyrights and licenses must be followed.
2. Redistributions of source code must retain the authors’ copyright notice(s), this list of conditions, and the
following disclaimer.
3. Redistributions in binary form must reproduce the authors’ copyright notice(s), this list of conditions, and
the following disclaimer in the documentation and/or other materials provided with the distribution.
4. [The copyright holder has authorized the removal of this clause.]
5. Neither the name(s) of the author(s) nor the names of its contributors may be used to endorse or promote
products derived from this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY ITS AUTHORS AND CONTRIBUTORS ``AS IS’’ AND ANY EXPRESS
OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT
SHALL THE AUTHORS OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR
BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
DAMAGE.
If these license terms cause you a real problem, contact the author. */
17
16. libpng
This copy of the libpng notices is provided for your convenience. In case of any discrepancy between this copy
and the notices in the file png.h that is included in the libpng distribution, the latter shall prevail.
COPYRIGHT NOTICE, DISCLAIMER, and LICENSE:
If you modify libpng you may insert additional notices immediately following this sentence.
This code is released under the libpng license.
libpng versions 1.2.6, August 15, 2004, through 1.2.41, December 3, 2009, are Copyright (c) 2004, 2006-2009
Glenn Randers-Pehrson, and are distributed according to the same disclaimer and license as libpng-1.2.5 with
the following individual added to the list of Contributing Authors
Cosmin Truta
libpng versions 1.0.7, July 1, 2000, through 1.2.5 - October 3, 2002, are
Copyright (c) 2000-2002 Glenn Randers-Pehrson, and are distributed according to the same disclaimer and
license as libpng-1.0.6 with the following individuals added to the list of Contributing Authors
Simon-Pierre Cadieux
Eric S. Raymond
Gilles Vollant
and with the following additions to the disclaimer:
There is no warranty against interference with your enjoyment of the library or against infringement. There
is no warranty that our efforts or the library will fulfill any of your particular purposes or needs. This library is
provided with all faults, and the entire risk of satisfactory quality, performance, accuracy, and effort is with the
user.
libpng versions 0.97, January 1998, through 1.0.6, March 20, 2000, are Copyright (c) 1998, 1999 Glenn Randers-
Pehrson, and are distributed according to the same disclaimer and license as libpng-0.96, with the following
individuals added to the list of Contributing Authors:
Tom Lane
Glenn Randers-Pehrson
Willem van Schaik
libpng versions 0.89, June 1996, through 0.96, May 1997, are Copyright (c) 1996, 1997 Andreas Dilger
Distributed according to the same disclaimer and license as libpng-0.88, with the following individuals added to
the list of Contributing Authors:
John Bowler
Kevin Bracey
Sam Bushell
Magnus Holmgren
Greg Roelofs
Tom Tanner
libpng versions 0.5, May 1995, through 0.88, January 1996, are Copyright (c) 1995, 1996 Guy Eric Schalnat,
Group 42, Inc.
For the purposes of this copyright and license, “Contributing Authors” is defined as the following set of
individuals:
Andreas Dilger
Dave Martindale
Guy Eric Schalnat
Paul Schmidt
Tim Wegner
The PNG Reference Library is supplied “AS IS”. The Contributing Authors and Group 42, Inc. disclaim all
warranties, expressed or implied, including, without limitation, the warranties of merchantability and of fitness
for any purpose. The Contributing Authors and Group 42, Inc. assume no liability for direct, indirect, incidental,
special, exemplary, or consequential damages, which may result from the use of the PNG Reference Library,
even if advised of the possibility of such damage.
18
Permission is hereby granted to use, copy, modify, and distribute this source code, or portions hereof, for any
purpose, without fee, subject to the following restrictions:
1. The origin of this source code must not be misrepresented.
2. Altered versions must be plainly marked as such and must not be misrepresented as being the original source.
3. This Copyright notice may not be removed or altered from any source or altered source distribution.
The Contributing Authors and Group 42, Inc. specifically permit, without fee, and encourage the use of this
source code as a component to supporting the PNG file format in commercial products. If you use this source
code in a product, acknowledgment is not required but would be appreciated.
A “png_get_copyright” function is available, for convenient use in “about” boxes and the like:
printf(“%s”,png_get_copyright(NULL));
Also, the PNG logo (in PNG format, of course) is supplied in the files “pngbar.png” and “pngbar.jpg (88x31) and
“pngnow.png” (98x31).
Libpng is OSI Certified Open Source Software. OSI Certified Open Source is a certification mark of the Open
Source Initiative.
Glenn Randers-Pehrson
glennrp at users.sourceforge.net
December 3, 2009
17. ezxml
This product contains ezxml, which is copyright 2004, 2005 Aaron Voisine.
18. SQLite
A l l o f t h e d e l i v e r a b l e c o d e i n S Q L i t e h a s b e e n d e d i c a t e d t o t h e H Y P E R L I N K
of the companies they work for, have signed affidavits dedicating their contributions to the public domain and
com”Hwaci. Anyone is free to copy, modify, publish, use, compile, sell, or distribute the original SQLite code,
either in source code form or as a compiled binary, for any purpose, commercial or non-commercial, and by any
means.
The previous paragraph applies to the deliverable code in SQLite - those parts of the SQLite library that you
actually bundle and ship with a larger application. Portions of the documentation and some code used as part
of the build process might fall under other licenses. The details here are unclear. We do not worry about the
licensing of the documentation and build code so much because none of these things are part of the core
deliverable SQLite library.
All of the deliverable code in SQLite has been written from scratch. No code has been taken from other
projects or from the open internet. Every line of code can be traced back to its original author, and all of those
authors have public domain dedications on file. So the SQLite code base is clean and is uncontaminated with
licensed code from other projects.
19. aes-src
Copyright (c) 1998-2008, Brian Gladman, Worcester, UK. All rights reserved.
LICENSE TERMS
The redistribution and use of this software (with or without changes) is allowed without the payment of fees or
royalties provided that:
1. source code distributions include the above copyright notice, this list of conditions and the following
disclaimer;
2. binary distributions include the above copyright notice, this list of conditions and the following disclaimer in
their documentation;
3. the name of the copyright holder is not used to endorse products built using this software without specific
written permission.
2010_BDP8000/9600_V2.0_SG
19
English
NOTICE
SOFTWARE END USER LICENSE AGREEMENT
THIS SOFTWARE END USER LICENSE AGREEMENT (“THIS AGREEMENT”) IS A LEGAL AND BINDING
AGREEMENT BETWEEN YOU (EITHER AN INDIVIDUAL OR ENTITY) AND PHILIPS CONSUMER LIFESTYLE B.V.
A DUTCH LIMITED LIABILITY COMPANY, WITH ITS PRINCIPAL OFFICE AT HIGH TECH CAMPUS 37, 5656 AE
EINDHOVEN, THE NETHERLANDS AND ITS SUBSIDIARY COMPANIES (INDIVIDUALLY AND COLLECTIVELY
“PHILIPS”). THIS AGREEMENT GIVES YOU THE RIGHT TO USE CERTAIN SOFTWARE (THE “SOFTWARE”)
INCLUDING USER DOCUMENTATION IN ELECTRONIC FORM WHICH MAY HAVE BEEN PROVIDED
SEPARATELY OR TOGETHER WITH A PHILIPS PRODUCT (THE “DEVICE”) OR A PC. BY DOWNLOADING,
INSTALLING OR OTHERWISE USING THE SOFTWARE, YOU ACCEPT AND AGREE TO BE BOUND BY ALL
OF THE TERMS AND CONDITIONS OF THIS AGREEMENT. IF YOU DO NOT AGREE TO THESE TERMS AND
CONDITIONS, DO NOT DOWNLOAD, INSTALL OR OTHERWISE USE THE SOFTWARE. IF YOU ACQUIRED THE
SOFTWARE IN TANGIBLE MEDIA E.G. CD WITHOUT THE OPPORTUNITY TO REVIEW THIS LICENSE AND DO
NOT ACCEPT THESE TERMS, YOU MAY RECEIVE A FULL REFUND OF THE AMOUNT, IF ANY, THAT YOU PAID
FOR THE SOFTWARE IF YOU RETURN THE SOFTWARE UNUSED WITH PROOF OF PAYMENT WITHIN 30 DAYS
FROM THE DATE OF PURCHASE.
1. Grant of License. This Agreement grants you a non-exclusive, nontransferable, non-sub licensable license to install
and use, on the Device or a PC, as applicable, one (1) copy of the specified version of the Software in object code
format as set out in the user documentation solely for your personal use. The Software is “in use” when it is loaded
into the temporary or permanent memory (i.e. RAM, hard disk, etc.) of the PC or the Device.
2. Ownership. The Software is licensed and not sold to you. This Agreement grants you only the right to use the
Software, but you do not acquire any rights, express or implied, in the Software other than those specified in this
Agreement. Philips and its licensors retain all right, title, and interest in and to the Software, including all patents,
copyrights, trade secrets, and other intellectual property rights incorporated therein. The Software is protected
by copyright laws, international treaty provisions, and other intellectual property laws. Therefore, other than as
expressly set forth herein, you may not copy the Software without prior written authorization of Philips, except that
you may make one (1) copy of the Software for your back-up purposes only. You may not copy any printed materials
accompanying the Software, nor print more than one (1) copy of any user documentation provided in electronic
form, except that you may make one (1) copy of such printed materials for your back-up purposes only.
3. License Restrictions. Except as provided otherwise herein, you shall not rent, lease, sublicense, sell, assign, loan,
or otherwise transfer the Software. You shall not, and you shall not permit any third party, to reverse engineer,
decompile, or disassemble the Software, except to the extent that applicable law expressly prohibits the foregoing
restriction. You may not remove or destroy any product identification, copyright notices, or other proprietary
markings or restrictions from the Software. All titles, trademarks, and copyright and restricted rights notices shall be
reproduced on your back up copy of the Software. You may not modify or adapt the Software, merge the Software
into another program or create derivative works based upon the Software.
4. Termination of certain functionality. The Software may contain components of certain licensed software including
software licensed from Microsoft Corporation (“Microsoft”) which implements Microsoft’s digital rights management
technology for Windows Media. Content providers are using the digital rights management technology for Windows
Media (“WM-DRM”) to protect the integrity of their content (“Secure Content”) so that their intellectual property,
including copyright, in such content is not misappropriated. Your Device may also use WM-DRM software to transfer
or play Secure Content (“WM-DRM Software”). If the security of such WM-DRM Software is compromised,
Microsoft may revoke (either on its own or upon the request of the owners of Secure Content (“Secure Content
Owners”)) the WM-DRM Software’s right to acquire new licenses to copy, store, transfer, display and/or play Secure
Content. Revocation does not alter the WM-DRM Software’s ability to play unprotected content. A list of revoked
WM-DRM Software is sent to your PC and/or your Device whenever you download a license for Secure Content.
Microsoft may, in conjunction with such license, also download revocation lists onto your Device on behalf of Secure
Content Owners, which may disable your Device’s ability to copy, store, display, transfer, and/or play Secure Content.
Secure Content Owners may also require you to upgrade some of the WM-DRM components distributed with this
Software (“WM-DRM Upgrades”) before accessing their content. When you attempt to play Secure Content, WM-
DRM Software built by Microsoft will notify you that a WM-DRM Upgrade is required and then ask for your consent
before the WM-DRM Upgrade is downloaded. WM-DRM Software built by Philips may do the same. If you decline
the upgrade, you will not be able to access Secure Content that requires the WM-DRM Upgrade; however, you
will still be able to access unprotected content and Secure Content that does not require the upgrade. WM-DRM
features that access the Internet, such as acquiring new licenses and/or performing a required WM-DRM Upgrade,
can be switched off. When these features are switched off, you will still be able to play Secure Content if you have
a valid license for such content already stored on your Device. However, you will not be able to use certain of the
WM-DRM Software features that require Internet access such as the ability to download content that requires the
WM-DRM Upgrade. All title and intellectual property rights in and to the Secure Content is the property of the
respective Secure Content owners and may be protected by applicable copyright or other intellectual property
laws and treaties. This Agreement grants you no rights to use such Secure Content. To summarize, if the Software
contains Microsoft WM-DRM components – Secure Content you desire to download, copy, store, display,
transfer, and/or play is protected by the Microsoft WM-DRM components of the Software. Microsoft, Secure
Content Owners, or Secure Content distributors may deny you access, or restrict your access, to Secure
Content even after you have paid for, and/or obtained, it. Neither your consent nor the consent or approval of
Philips is necessary for any of them to deny, withhold or otherwise restrict your access to Secure Content. Philips
does not guaranty that you will be able to download, copy, store, display, transfer, and/or play Secure Content.
5. Open Source Software. (a) This software may contain components that are subject to open-source terms, as stated
in the documentation accompanying the Device. This Agreement does not apply to this software as such. (b) Your
license rights under this Agreement do not include any right or license to use, distribute or create derivative works of
the Software in any manner that would subject the Software to Open Source Terms. “Open Source Terms” means
the terms of any license that directly or indirectly (1) create, or purport to create, obligations for Philips with respect
to the Software and/or derivative works thereof; or (2) grant, or purport to grant, to any third party any rights or
immunities under intellectual property or proprietary rights in the Software or derivative works thereof.
6. Termination. This Agreement shall be effective upon installation or first use of the Software and shall terminate (i) at
the discretion of Philips, due to your failure to comply with any term of this Agreement; or (ii) upon destruction of all
copies of the Software and related materials provided to you by Philips hereunder. Philips’s rights and your obligations
shall survive the termination of this Agreement.
7. Upgrades. Philips may, at its sole option, make upgrades to the Software available by general posting on a website or
by any other means or methods. Such upgrades may be made available pursuant to the terms of this Agreement or
the release of such upgrades to you may be subject to your acceptance of another agreement.
8. Support Services. Philips is not obligated to provide technical or other support (“Support Services”) for the
Software. If Philips does provide you with Support Services, these will be governed by separate terms to be agreed
between you and Philips.
9. Limited Software Warranty. Philips provides the Software ‘as is’ and without any warranty except that the Software
will perform substantially in accordance with the documentation accompanying the Software for a period of one year
after your first download, installation or use of the Software, whichever occurs first. Philips’ entire liability and your
exclusive remedy for breach of this warranty shall be, at Philips’ option, either (i) return of the price paid by you for
the Software (if any); or (b) repair or replacement of the Software that does not meet the warranty set forth herein
and that is returned to Philips with a copy of your receipt. This limited warranty shall be void if failure of the Software
has resulted from any accident, abuse, misuse or wrongful application. Any replacement Software will be warranted
for the remainder of the original warranty period or thirty (30) days, whichever is longer. This limited warranty shall
not apply to you if the Software was provided to you free of charge on an evaluation only basis.
10. NO OTHER WARRANTIES. EXCEPT AS SET FORTH ABOVE, PHILIPS AND ITS LICENSORS DO NOT
WARRANT THAT THE SOFTWARE WILL OPERATE ERROR FREE OR UNINTERRUPTED, OR WILL MEET
YOUR REQUIREMENTS. YOU ASSUME ALL RESPONSIBILITIES FOR SELECTION OF THE SOFTWARE TO
ACHIEVE YOUR INTENDED RESULTS, AND FOR THE INSTALLATION OF, USE OF, AND RESULTS OBTAINED
FROM THE SOFTWARE. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, PHILIPS AND
ITS LICENSORS DISCLAIM ALL WARRANTIES AND CONDITIONS, WHETHER EXPRESS OR IMPLIED,
INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR
A PARTICULAR PURPOSE, AND ACCURACY OR COMPLETENESS OF RESULTS WITH RESPECT TO THE
SOFTWARE AND THE ACCOMPANYING MATERIALS. THERE IS NO WARRANTY AGAINST INFRINGEMENT.
PHILIPS DOES NOT WARRANT THAT YOU WILL BE ABLE TO DOWNLOAD, COPY, STORE, DISPLAY,
TRANSFER, AND/OR PLAY SECURE CONTENT.
11. LIMITATION OF LIABILITY. UNDER NO CIRCUMSTANCES WILL PHILIPS OR ITS LICENSORS BE LIABLE
FOR ANY CONSEQUENTIAL, SPECIAL, INDIRECT, INCIDENTAL OR PUNITIVE DAMAGES WHATSOEVER,
INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS OR REVENUES, BUSINESS
INTERRUPTION, LOSS OF BUSINESS INFORMATION, LOSS OF DATA, LOSS OF USE OR OTHER PECUNIARY
LOSS, EVEN IF PHILIPS OR ITS LICENSORS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
IN NO EVENT SHALL PHILIPS’ OR ITS LICENSORS’ AGGREGATE LIABILITY FOR DAMAGES ARISING OUT OF
THIS AGREEMENT EXCEED THE GREATER OF THE PRICE ACTUALLY PAID BY YOU FOR THE SOFTWARE
OR FIVE POUNDS STERLING (5.00).
12. Trademarks. Certain of the product and Philips names used in this Agreement, the Software, and the printed user
documentation may constitute trademarks of the Philips, its licensors or other third parties. You are not authorized
to use any such trademarks.
13. Export Administration. You agree that you will not directly or indirectly, export or re-export the Software to
any country for which the United States Export Administration Act, or any similar United States law or regulation
requires an export license or other U.S. Government approval, unless the appropriate export license or approval has
first been obtained. By downloading or installing the Software you agree to abide by this Export provision.
14. Governing law. This Agreement is governed by the laws of your country of residence , without reference to its
conflict of laws principles. Any dispute between you and Philips regarding this Agreement shall be subject to the non-
exclusive jurisdiction of the courts of your country of residence.
15. General. This Agreement contains the entire agreement between you and Philips and supersedes any prior
representation, undertaking or other communication or advertising with respect to the Software and user
documentation. If any part of this Agreement is held invalid, the remainder of this Agreement will continue in full
force and effect. This Agreement shall not prejudice the statutory rights of any party dealing as a consumer.
EULA-English (UK)
September 2009
© 2010 Koninklijke Philips Electronics N.V.
All rights reserved.
BDP9600_51_UM_V1.0_1043
|