Owner’s Manual
Dual Camera
Model No.HX-DC10
HX-DC1
Before connecting, operating or adjusting this product, please read the instructions completely.
For USA and Puerto Rico assistance, please call: 1-800-211-PANA(7262) or,
contact us via the web at: http://www.panasonic.com/contactinfo
VQT3M88
P
1AG6P1P6280--(S)
FCC Note:
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
i Reorient or relocate the receiving antenna.
i Increase the separation between the equipment and receiver.
i Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
i Consult the dealer or an experienced radio/TV technician for help.
FCC Caution:
To assure continued compliance, follow the attached
installation instructions and use only shielded
interface cables with ferrite core when connecting to
computer or peripheral devices.
Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate this
equipment.
Declaration of Conformity
Trade Name:
Model No.:
Panasonic
HX-DC10/HX-DC1
Responsible party: Panasonic Corporation of North America One
Panasonic Way, Secaucus, NJ 07094
Support Contact: Panasonic Consumer Electronics Company 1-800-
211-PANA (7262)
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
HX-DC10
HX-DC1
VQT3M88
3
AC adaptor
This AC adaptor operates on AC between 100V and 240V.
But
i In the U.S.A. and Canada, the AC adaptor must be connected to a
120V AC power supply only.
i When connecting to an AC supply outside of the U.S.A. or Canada,
use a plug adaptor to suit the AC outlet configuration.
THE SOCKET OUTLET SHALL BE INSTALLED NEAR THE
EQUIPMENT AND SHALL BE EASILY ACCESSIBLE.
k Concerning the battery
Battery pack (Lithium ion battery pack)
i Use the specified unit to recharge the battery pack.
i Do not use the battery pack with equipment other than the specified
unit.
i Do not get dirt, sand, liquids, or other foreign matter on the terminals.
i Do not touch the plug terminals (+ and -) with metal objects.
i Do not disassemble, remodel, heat or throw into fire.
If any electrolyte should come into contact with your hands or clothes,
wash it off thoroughly with water.
If any electrolyte should come into contact with your eyes, never rub the
eyes. Rinse eyes thoroughly with water, and then consult a doctor.
Warning
Risk of fire, explosion and burns. Do not disassemble, heat above 60 °C
(140 °F) or incinerate.
4
VQT3M88
CAUTION
Danger of explosion if battery is incorrectly replaced. Replace only with
the same or equivalent type recommended by the manufacturer. Dispose
of used batteries according to the manufacturer’s instructions.
k Product Identification Marking
Product
Dual Camera
Location
Battery holder
U.S.A./CANADA CONSUMERS: ATTENTION:
A lithium ion battery that is recyclable powers the product
you have purchased. Please call 1-800-8-BATTERY for
information on how to recycle this battery.
VQT3M88
5
i DO NOT EXPOSE YOUR
CAMERA TO EXTENDED HIGH
TEMPERATURE ... Such as, in
direct sunlight, inside a closed
car, next to a heater, etc... This
action could permanently
damage the internal parts of your
camera.
i AVOID SUDDEN CHANGES IN
TEMPERATURE ... If the unit is
suddenly moved from a cold
place to a warm place, moisture
may form on the SD card and
inside the unit.
Precautions
USE & LOCATION
WARNING
i TO AVOID SHOCK HAZARD ...
Your camera and power supply
should not be exposed to rain or
moisture. Do not connect the
power supply or operate your
camera if it gets wet. Your
camera has been designed for
outdoor use, however it is not
designed to sustain direct
exposure to water, rain, sleet,
snow, sand, dust, or a direct
splashing from a pool or even a
cup of coffee. This action could
permanently damage the internal
parts of your camera. Do not
attempt to disassemble this unit.
There are no user serviceable
parts inside. Unplug your camera
from the power supply before
cleaning.
i DO NOT LEAVE YOUR
CAMERA OR THE POWER
SUPPLY TURNED ON WHEN
NOT IN USE.
i STORAGE OF YOUR CAMERA
... Store and handle your camera
in a manner that will not subject it
to unnecessary movement (avoid
shaking and striking). Your
camera contains a sensitive pick-
up device which could be
damaged by improper handling
or storage.
i AS WITH ANY SMALL OBJECT,
SD CARDS CAN BE
SWALLOWED BY YOUNG
CHILDREN. DO NOT ALLOW
CHILDREN TO HANDLE THE
SD CARD.
CARE
i TO CLEAN YOUR CAMERA ...
Do not use strong or abrasive
detergents when cleaning your
camera body.
i TO PROTECT THE LENS ... Do
not touch the surface of the lens
with your hand. Use a
commercial camera lens solution
and lens paper when cleaning
the lens. Improper cleaning can
scratch the lens coating.
CAUTION
i DO NOT AIM YOUR CAMERA
AT THE SUN OR OTHER
BRIGHT OBJECTS
i DO NOT LEAVE THE CAMERA
WITH THE EVF AIMED
DIRECTLY AT THE SUN AS
THIS MAY CAUSE DAMAGE TO
THE INTERNAL PARTS OF THE
EVF
6
VQT3M88
i TO PROTECT THE FINISH OF
YOUR CAMERA ... Before
handling your camera, make sure
your hands and face are free
from any chemical products, such
as sunblock, as it may damage
the finish.
-If you see this symbol-
Information on Disposal in other
Countries outside the European
Union
This symbol is only
valid in the
European Union. If
you wish to discard
this product, please
contact your local
authorities or
dealer and ask for
the correct method
of disposal.
VQT3M88
7
IMPORTANT! PLEASE READ
k About the models covered by this owner’s manual
i This manual pertains to models HX-DC10 and HX-DC1.
i Where passages refer to a specific model(s), the model number is
indicated.
k Be sure to take some test pictures beforehand
Before those important events, be sure to take some trial pictures to confirm
that the images and audio are being properly recorded.
k Indemnity about recorded content
Panasonic does not accept any responsibility for damages directly or
indirectly due to any type of problems that result in loss of recording or edited
content, and does not guarantee any content if recording or editing does not
work properly. Likewise, the above also applies in a case where any type of
repair is made to the unit (including any other non-built-in memory/HDD
related component).
k Handling of built-in memory
This unit is equipped with an built-in memory (HX-DC10: Approx. 80 MB, HX-
DC1: Approx. 80 MB). When using this component, pay attention to the
following points.
Back up data periodically.
The built-in memory is temporary storage. In order to avoid erasing data
due to static electricity, electromagnetic waves, breakage, and failures,
back up the data to a computer or DVD disc. (page 129)
i The status indicator (page 21) illuminates while the SD card or built-in
memory is being accessed (reading, recording, playback, deleting etc.). Do
not perform the following operations when the lamp illuminates. It may
damage the built-in memory or cause a malfunction in the unit.
h Turn the unit off (remove the battery)
h Eject the SD card from the camera
h Insert or remove the USB cable
h Expose the unit to vibrations or shock
i For disposing of or transferring this unit, please see page 118.
8
VQT3M88
k Concerning this unit’s recording method and compatibility
<Video compatibility>
i This camera is an MP4 standard (MPEG-4AVC/H.264 format) digital movie
camera that records high-definition HDTV video.
The AVCHD and MPEG2 video formats are different and are therefore not
compatible.
i This camera may degrade or be unable to play back videos recorded or
created with other products, and other products may degrade or not be
able to play back videos recorded with this camera, even if the products
support the MP4 format.
<Photo compatibility>
i This unit is compliant with the unified standard DCF (Design rule for
Camera File system) established by JEITA (Japan Electronics and
Information Technology Industries Association) and with Exif
(Exchangeable Image File Format). Files which do not comply with the
DCF standard cannot be played back.
i The file format of images supported by this unit is JPEG. (Not all JPEG
format files will be played back.)
i This unit may degrade or not play back images recorded or created on
other products, and other products may degrade or not play back images
recorded on this unit.
k About the battery pack
i Never place the battery pack within the reach of infants. In the event that
the battery pack is swallowed, consult a doctor immediately.
k About the photos and illustrations in this manual
i The product images, illustrations, menu displays etc. in this manual may
differ slightly from the actual product.
i Unless noted otherwise, the screen and camera illustrations are those of
Model HX-DC10.
k For the purposes of this owner’s manual
i SD Memory Card, SDHC Memory Card and SDXC Memory Card are
referred to as the “SD card”.
i Pages for reference are indicated by parentheses, for example: (page 00).
VQT3M88
9
WHAT YOU CAN DO WITH YOUR
DIGITAL MOVIE CAMERA
Easy shooting/playback (Basic features)
Intelligent Auto Mode
1080-30
p
-
M
S
35316
000:15:53
(HX-DC10)
... (page 48)
Just point the camera at the subject, and
it automatically ascertains the scene
and captures the images with the
optimum settings.
Shoot movies
... (page 53)
p
001008:0-0300:09
2
M
Take photos
... (page 54)
-
16M
S
F3.5
1/30
Play back videos and
photos
... (page 59)
DEC.20.2011
10 VQT3M88
Using the convenient features (Practical
applications)
Image stabilizer... (pages 43, 74)
Subject tracking... (pages 45, 80)
Scene mode... (pages 41, 72, 171 to 173)
HINT
User guide on the Internet
When this camera is connected to an Internet-connected VIERA via an HDMI
mini cable (sold separately), you can press the VIERA’s remote control Menu
button and from the resulting menu select “User guide on the Internet” to see
easy-to-understand explanations of the camera’s operation and convenient
functions on the VIERA screen.
i Applicable to VIERA units sold from December 2010.
i To connect the camera to the VIERA via an HDMI mini cable, please see
pages 150 to 152.
VQT3M88 11
Keeping recorded videos (Copy/dubbing)
From built-in memory to SD
card...
(page 47)
DVD recorder and video deck...
(page 154)
* It is not possible to directly insert in the card slot
an SD card recorded with this camera and play
back or dub from it.
* It is not possible to connect the camera to the
USB connector and play back or dub from it.
* Recording with HD image quality on a Blu-ray
disc recorder is not possible.
On a computer...
(pages 123 to 148)
12 VQT3M88
CONTENTS
CHECKING THE INCLUDED ACCESSORIES ....................................17
ABOUT THE CARD ..............................................................................18
Media cards that can be used with this camera
„ SETUP
PARTS NAMES ....................................................................................20
CHARGING THE BATTERY PACK ......................................................23
About the temperature alert icon
TURNING THE CAMERA ON AND OFF ..............................................32
Turning on the camera when it is in the sleep mode .....................33
Date and time backup ...................................................................36
SWITCHING BETWEEN THE RECORDING MODE AND PLAYBACK
MODE ...............................................................................................37
MENU SCREEN ...................................................................................38
Accessing/exiting the Menu Screen ..............................................38
Using the Menu .............................................................................39
Overview of the Menu Screen .......................................................40
INTELLIGENT AUTO MODE (HX-DC10) .............................................48
„ BASIC OPERATION
SHOOTING
BEFORE TAKING PICTURES .............................................................51
For best results ..............................................................................51
How to use the accessories ..........................................................52
VIDEO RECORDING ............................................................................53
TAKING PHOTOS ................................................................................54
Shoot a photo while recording a video ..........................................56
MACRO-PHOTOGRAPHY (ZOOM) .....................................................57
PLAYBACK
PLAYING BACK VIDEOS AND PHOTOS ............................................59
How to save one frame from a video as a photo ...........................62
DELETING FILES .................................................................................63
Delete single/delete all/delete folder .............................................63
Delete selected ..............................................................................64
VQT3M88 13
PLAYBACK MODES ............................................................................ 66
„ ADVANCED OPERATION
SHOOTING
RECORDING MENU 1 ......................................................................... 68
Recording mode setting (page 40) ............................................... 68
Recorded pixels (page 40) ............................................................ 71
Scene mode setting (page 41) ...................................................... 72
RECORDING MENU 2 ......................................................................... 74
Focus setting (page 43) ................................................................ 75
ISO sensitivity setting (page 43) ................................................... 76
White balance setting (page 43) ................................................... 77
RECORDING MENU 3 ......................................................................... 78
Exposure setting (HX-DC10) (page 45) ........................................ 78
Subject tracking settings (page 45) .............................................. 80
Shortcut setting (page 45) ............................................................ 82
Exposure compensation ............................................................... 85
PLAYBACK
PLAYBACK MENU 1 ........................................................................... 86
Slideshow settings (page 46) ........................................................ 86
File protect setting (page 46) ........................................................ 87
Rotate (page 46) ........................................................................... 89
Resize (page 46) .......................................................................... 89
PLAYBACK MENU 2 ........................................................................... 90
Correcting red-eye (page 47) ........................................................ 90
Editing videos (page 47) ............................................................... 91
Copy (page 47) ........................................................................... 100
FILE INFO DISPLAY .......................................................................... 102
„ OPTION SETTINGS
DISPLAY THE OPTION SETTING MENU ......................................... 103
INTRODUCTION TO THE OPTION SETTING MENU ...................... 104
TV output setting (page 107) ...................................................... 110
Storage folder setting (page 109) ............................................... 114
Playback folder setting (page 109) ............................................. 115
File No. continued setting (page 109) ......................................... 116
Formatting (initializing) (page 107) ............................................. 118
14 VQT3M88
CHECKING THE REMAINING CARD MEMORY ...............................119
Checking the remaining number of images and
video recording time ................................................................119
Check the available audio recording time ...................................120
CONNECTING TO A COMPUTER
SETTING THE CONNECTION MODE ...............................................123
USING AS A CARD READER ............................................................125
ABOUT THE CONTENTS OF THE CARD .........................................126
Configuration of directories in the card ........................................126
File formats ..................................................................................126
USING AS A WEBCAM ......................................................................130
Operating environment ................................................................130
Using as a webcam .....................................................................131
WHAT YOU CAN DO WITH A COMPUTER ......................................132
Contents of the supplied CD-ROM ..............................................132
End User License Agreement .....................................................134
OPERATING ENVIRONMENT ...........................................................136
Operating environment for HD Writer VE 1.0 ..............................136
To use the HD Writer VE 1.0 .......................................................139
Operating environment for the card reader function
(mass storage) ........................................................................140
INSTALLATION ..................................................................................141
Uninstalling HD Writer VE 1.0 .....................................................144
STARTING HD WRITER VE 1.0 ........................................................145
Reading the owner’s manual of the software applications ..........146
IF USING Mac ....................................................................................147
Operating environment ................................................................147
Copying photos on a computer ...................................................147
To disconnect USB cable safely ..................................................148
CONNECTING TO A TV
CONNECTING TO A TV .....................................................................149
Connecting to a video input terminal ...........................................150
Connecting to the HDMI terminal ................................................150
PLAYING BACK ON A TV ..................................................................151
Playback using VIERA Link™ (HDAVI Control™) .......................151
VQT3M88 15
COPYING/DUBBING
COPYING/DUBBING ......................................................................... 154
Dubbing in standard picture quality ............................................ 154
„ IMPORTANT MESSAGES AND ALERTS
COMMONLY ASKED QUESTIONS ................................................... 156
TROUBLESHOOTING ....................................................................... 164
Camera ....................................................................................... 164
Restrictions concerning the Scene Mode and
Color Mode features ............................................................... 171
ABOUT COPYRIGHT ........................................................................ 174
CAUTIONS FOR USE ....................................................................... 175
RECORDING MODES/APPROXIMATE RECORDABLE TIME ......... 181
APPROXIMATE NUMBER OF RECORDABLE PICTURES .............. 183
SPECIFICATIONS ............................................................................. 185
OPTIONAL ACCESSORIES .............................................................. 191
Limited Warranty (ONLY FOR U.S.A. AND PUERTO RICO) ............ 193
Spanish Quick Use Guide/Guía española para el uso rápido ............ 196
16 VQT3M88
CHECKING THE INCLUDED ACCESSORIES
Check the accessories before using this unit.
Product numbers correct as of February, 2011.
These may be subject to change.
ꢀ Battery pack
VW-VBX070
ꢀ AC adaptor
VSK0750
ꢀ USB cable
VFA0544
ꢀ AV cable
VFA0543
ꢀ Lens cap
VFC4701
ꢀ CD-ROM
Software
Lens cap strap
VFC4702
ꢀ Handstrap
* To prevent the camera from
dropping, be sure to attach the
handstrap (page 52).
VFC4627
i Please dispose of packing materials properly.
i Keep the battery pack and the lens cap out of reach of children to
prevent swallowing.
VQT3M88 17
ABOUT THE CARD
Media cards that can be used with this camera
(as of February 2011)
Use SD cards conforming to Class 4 or higher of the SD Speed Class Rating*
for video recording.
This camera is compatible with SDXC devices (SD Memory Card/SDHC
Memory Card/SDXC Memory Card compatible devices). If using an
SDHC memory card/SDXC memory card in different device, please
confirm that it is compatible with the respective memory card.
Photo
shooting
Card type
Capacity
Video recording
8 MB/16 MB/
32 MB/64 MB/
128 MB/256 MB
Operation
is not
guaranteed.
Operation is not
guaranteed.
SD Memory
Card
512 MB/
1 GB/ 2 GB
4 GB/6 GB/
8 GB/12 GB/
16 GB/
SDHC Memory
Card
Can be used.
Can be used.
24 GB/32 GB
SDXC Memory 48 GB/64 GB
Card
* The SD Speed class Rating is the speed standard for successive writes.
See the card label to confirm the rating.
(Example)
Please confirm which of our SD Memory Cards/SDHC Memory Cards/
SDXC Memory Cards can be used with this product by visiting the
support web site at the address below.
http://panasonic.jp/support/global/cs/e_cam
(This website is in English only.)
18 VQT3M88
i 4 GB or more Memory Cards that do not have the SDHC logo or 48 GB or
more Memory Cards that do not have the SDXC logo are not based on SD
Memory Card specifications.
i Cards with capacity larger than 64 GB cannot be used.
i When the write-protect switch on the SD card is locked, no recording,
deletion or editing will be possible on the card.
i Keep the Memory Card out of reach of children to prevent swallowing.
Write-protect switch
VQT3M88 19
SETUP
SETUP
PARTS NAMES
Front
Status indicator
Speaker
Monitor unit
Lens
Internal stereo
microphone
Flash
i The flash unit
becomes very
hot and may
cause a burn.
Avoid touching
the flash unit
when shooting.
* The tripod mounting
hole is on the bottom.
Attaching to a tripod
having a screw length
longer than 5.5 mm
(0.22”) may damage the
camera.
20 VQT3M88
k About the status indicator (See page 173 regarding the charging
status.)
i The status indicator lights or flashes to
show the camera’s operating status.
Status indicator
Status indicator status
Camera
status
Color
Lit/flashing
Lit
Accessing
built-in
memory or
SD card
Flashing
(Faster)
Battery
charge
error
Red
Flashing
(Fast)
Self-timer
is operating
Flashing
(Slow)
Battery is
charging
Flashing
(Slower)
Lit
USB
connection
Green
Flashing
Lit
During
sleep mode
AV cable/
HDMI mini
cable
Orange
connection
VQT3M88 21
Rear
LCD monitor
Power button
Hand strap eyelet
(page 52)
terminal cover
Battery cover
USB/AV terminal
HDMI terminal
k Operation pad
HX-DC10
Zoom switch*
button
[O] button
Photo shooting button
[@] button
Video recording button
SET button
MENU button
REC/ button
HX-DC1
Zoom switch*
ZOOM RANGE
button
[O] button
[@] button
Photo shooting button
Video recording button
MENU button
SET button
REC/ button
* During recording: zoom photography [W/T] (page 57)
During playback: volume adjustment (page 60 and 70), image
magnification (page 67), playback display switching (page 66)
22 VQT3M88
CHARGING THE BATTERY PACK
At the time of purchase, the battery pack is not charged. Please charge it fully
before using it.
It has been found that counterfeit battery packs which look very similar to
the genuine product are made available to purchase in some markets.
Some of these battery packs are not adequately equipped with protective
devices to meet the requirements of appropriate safety standards. There
is a possibility that these battery packs may lead to fire or explosion.
Please be advised that we are not liable for any accident or failure
occurring as a result of use of a counterfeit battery pack. To ensure that
safe products are used we recommend that a genuine Panasonic battery
pack be used.
Guide to charging time and recording capacity
k Charging/recording time
i Temperature: 25 °C (77 °F)/humidity: 60 %RH
i It is recommended that the battery be recharged in a place where the
ambient temperature (and the battery temperature as well) is between
10 °C and 30 °C (50 °F to 86 °F). (The battery temperature should also be
the same.)
The indicated charging time is for when the AC adaptor is used for
charging.
<HX-DC10>
Battery model
number [voltage/
capacity (minimum)]
Maximum
continuous
recordable time
Actual
recordable
time
Charging Recording
time
mode
Approx.
30 min
Approx. 1 h
Supplied battery/
VW-VBX070
(optional)
Approx.
2 h
Approx.
1 h 10 min
[3.7 V/700 mAh]
Approx.
1 h 15 min
Approx.
35 min
Approx.
1 h 10 min
Approx.
1 h 20 min
<
-
VQT3M88 23
<HX-DC1>
Battery model
number [voltage/
capacity (minimum)]
Maximum
continuous
recordable time
Actual
recordable
time
Charging Recording
time
mode
Approx.
30 min
Approx. 50 min
Approx. 1 h
Supplied battery/
VW-VBX070
(optional)
Approx.
2 h
Approx.
35 min
[3.7 V/700 mAh]
Approx.
1 h 25 min
Approx.
40 min
Approx.
1 h 5 min
Approx.
35 min
Approx.
1 h 30 min
<
-
i These times are approximations.
i The indicated charging time is for when the battery has been discharged
completely. Charging time and recordable time vary depending on the
usage conditions such as high/low temperature.
i The actual recordable time refers to the recordable time when repeatedly
starting/stopping recording, turning the unit on/off, moving the zoom lever
etc.
i The batteries heat up after use or charging. This is not a malfunction.
i See page 121 concerning the remaining battery pack charge.
i Always use genuine Panasonic batteries (VW-VBX070).
i If you use other batteries, we cannot guarantee the quality of this product.
i Do not heat or expose to flame.
i Do not leave the battery in an automobile exposed to direct sunlight for a
long period of time with doors and windows closed.
24 VQT3M88
Approximate operating time and number of
recordable images
<HX-DC10>
Number of
recordable images
Approx.
170 images
By CIPA standard
Approx. 180 min
Recording time
Playback time
Approx. 85 min
<HX-DC1>
Number of
recordable images
Approx.
180 images
By CIPA standard
Approx. 180 min
Recording time
Playback time
Approx. 90 min
Recording conditions by CIPA standard
i CIPA is an abbreviation of Camera & Imaging Products Association.
i Using the supplied battery
i Using a Panasonic SD Memory Card (2 GB)
VQT3M88 25
1
Insert the battery pack.
h It is possible to insert the battery incorrectly, so please pay particular
attention when inserting that it is correctly oriented.
Connector
markings
Battery cover
1 Push
out
Battery
pack
3 Open
2
4 Insert by matching the connector markings
<To remove the battery pack...>
i
Be sure the turn off the camera by
pressing the power button until
the status indicator (page 21)
turns off before removing the
battery pack.
Raise the end of the battery pack
to remove it.
5 Close
i
6 Close firmly
until you hear
a click.
26 VQT3M88
2
Use the USB cable (supplied) to connect the camera and the AC
adaptor, and then connect the AC adaptor to a power outlet.
h Use only the supplied USB cable. Operation is not guaranteed if
a different USB cable is used.
h The AC adaptor is for this camera only. Do not use it with other
devices.
h Recharging takes place only when the camera is turned off or is in the
sleep mode (page 33). Recharging does not take place when the
camera is in the recording mode or playback mode.
3 To power
outlet
1 Open
2
AC adaptor
To AC adaptor
h Do not use any other AC adaptors except the supplied one.
h Do not use any other USB cables except the supplied one.
<During charging...>
h The status indicator flashes red at 0.5-second intervals if the battery
pack is defective or is not installed correctly. Make sure that the
battery pack is correctly installed.
h If the battery pack still fails to recharge, it is possible that there is a
malfunction in the camera, the battery pack or the AC adaptor. In case
the status indicator is flashing fast or slow, please see page 173.
h When charging is completed, the status indicator turns off.
h The charging time is approx. 120 minutes.
Status indicator
VQT3M88 27
HINT
Recharging when connected to a computer (page 123)
i The battery can be recharged while the camera is connected to a
computer.
i Use only the supplied USB cable. Operation is not guaranteed if a different
USB cable is used.
i The charging time is two to three times longer than when the AC adaptor is
used to charge the battery pack.
i It is not possible to charge the battery if the status indicator flashes fast
and then turns off, or if it doesn't light at all. In this case, use the AC
adaptor to charge the battery.
i Connect the USB cable to the USB terminal on your computer. Do not
connect it to the USB terminal on the monitor or the keyboard, or to the
USB hub.
i If the camera is not going to be used for an extended period of time, please
disconnect the USB cable from the camera.
Do not use the battery with the outer covering or label removed
i Doing so may result in malfunction.
When not using the camera for a long time, remove the battery pack
i A small amount of power is still used even if the camera is turned off, and it
is therefore recommended that the battery pack be removed from the
camera if it is not going to be used for a long time. Note that when the
battery pack is removed for a long period, the time and date settings may
be cleared. Before using your camera again, be sure to confirm that the
camera settings are correct.
To maximize the battery pack life
i The battery pack is a consumable product, but the battery life can be
prolonged by heeding the following suggestions.
h Don’t leave the battery pack in a high-temperature environment, such as
outside in extremely hot weather in the summer.
h Don’t repeatedly charge the battery pack when it is fully charged. After a
full recharge, the battery should be used for a while before charging
again.
h For prolonged periods of unuse, avoid fully charging the battery pack,
and store it in a cool dark place.
28 VQT3M88
About the temperature alert icon
During camera use, if the temperature of the battery or inside the camera
(excluding the battery) rises, a temperature alert icon
described below.
will appear as
k When the battery or internal camera (excluding battery) temperature
rises during use
h During camera use, if the temperature of the battery or inside the
camera (excluding the battery) rises, a
icon lights on the LCD
monitor. It is still possible to record and play back even when the
icon is lit; however it is advised that you discontinue use as soon as
possible and turn the camera off.
h If the temperature rises further, the
icon will start to flash, and the
camera will turn off automatically.
The camera cannot be turned on until the temperature has dropped (or
as long as the icon remains flashing). Please wait until the
temperature has dropped before resuming use.
h If the camera is turned off while the temperature is high (that is, while
the
icon is flashing), it cannot be turned on again until the
temperature has dropped (or as long as the
icon remains flashing).
VQT3M88 29
INSTALLING THE CARD
Before using a newly purchased card or one that was used in another device,
be sure to format it with this camera (page 107 and 118). If an unformatted
card is used, the card itself may become unusable.
1 Open
2 Insert the card
i Push straight in
until you hear a
click.
3 Close
Card’s label side
4 Close firmly
until you hear
a click.
<When removing the card...>
h To remove the card, press it in, and then release. The card will
protrude slightly, and you can then pull it out.
2 Pull the card
out straight.
1 Push the middle part of the card.
30 VQT3M88
HINT
Do not attempt to forcibly remove the card
i Doing so may damage the card or the stored files.
If the status indicator is lit red...
i Never remove the card when the status indicator is flashing red, as doing
so may result in loss of files stored in the card.
VQT3M88 31
Turning off the camera
1
Press the power button for at least 1 second.
h The camera turns off.
h If you briefly press the power button, once, the camera will switch to
the sleep mode.
Turning on the camera when it is in the sleep
mode
In order to preserve battery pack power, the ECONOMY function operates to
automatically turn off the camera (sleep mode) after about 5 minutes of no
use during shooting, or about 5 minutes of no use during playback (factory-
preset settings).
i When the camera is in the sleep mode, it turns on when the monitor unit is
opened or one of the camera’s buttons is pressed.
i When the AC adaptor is connected, the ECONOMY mode will become
active about 5 minutes after the camera is turned on (factory-preset
setting).
i The user can specify the time elapsed before the sleep mode is activated
(page 105).
HINT
About the standby mode
i The camera goes into the standby mode if you close the monitor unit, or if
you leave it in the sleep mode for about 1 hour. The standby mode uses
almost no power.
i Open the monitor unit, or press the power button briefly, and the camera
turns on immediately and you are ready to shoot or view images without
any delay. Use the standby mode to turn off the camera only briefly, or if
you want to be able to use it immediately.
i If you close the monitor unit while recording a video, recording stops and
the camera switches to the standby mode.
VQT3M88 33
DATE AND TIME SETTING
The camera will record the date and time an image or audio recording is
taken so that you can display them during playback. Therefore, before
capturing images, make sure the correct date and time are set.
h If the screen to set the date and time appears when you turn on the
camera, skip to step 3 and follow the steps to set the date and time.
h To correct the date and time setting, please see under HINT on page 36.
Example: To set the clock to 7:30 p.m. on December 20, 2011
1
2
Turn on the camera (page 32), and display Option Setting Menu 1
(page 103).
Select [CLOCK SET] and press
CLOCK SET
the SET button.
DATE
TIME
DISP
JAN/01/2011
12:00 AM
M / D / Y
h The Clock Set Screen appears.
h Follow the procedures below to
enable or disable the date
display during playback, to set
the display format for the date,
and to set the date and time.
SET
ENTER
3
Set the date.
1 Select [DATE].
2 Press the SET button.
h The Set Date Screen
appears.
CLOCK SET
DATE
DEC/20/2011
3 Set the date to “DEC/20/2011”.
h The date is set in the
following order: Set the
month → Set the day → Set
the year.
SET
ENTER
h Toggle the SET button left or
right to select month, day or
year. Toggle the SET button
up or down to increase or
decrease the number.
4 Press the SET button.
34 VQT3M88
4
5
Set the clock.
1 Select [TIME].
2 Press the SET button.
h The Set Time Screen
appears.
CLOCK SET
TIME
07 : 30 PM
ENTER
3 Set the time to “07:30 PM”.
h The time is set in the
following order: Set the hour
→ Set the minute.
SET
4 Press the SET button.
Set the order in which the date is
displayed during playback.
1 Select [DISP].
CLOCK SET
2 Press the SET button.
h The Set Date Format Screen
appears.
M / D / Y
ENTER
DISP
3 Toggle the SET button up or
down.
SET
h The order of the date display
changes.
4 Press the SET button.
6
Press the MENU button.
h The date and time setting is completed.
h To display the Recording or Playback Screen, press the MENU button.
VQT3M88 35
HINT
To correct the date and time settings
1 Turn on the camera.
2 Display the Option Setting Menu 1 (page 103).
3 Select [CLOCK SET] and press the SET button.
h The screen to set the date and time appears.
h The current date and time settings are shown.
4 Select the line you wish to change, and make the correction.
If the camera’s date and time are not set...
h The screen display and capture date information will show as follows:
* The date and time format is determined by the [DISP] setting specified
on the Clock Set Screen.
Recording Screen display: ---.--.---- --:--
Photo capture date/time information: JAN/01/2011 00:00:00
Video/audio file recording date/time information: JAN/01/2011 00:00:00
Date and time backup
Under normal conditions, while the battery pack is being replaced, an internal
battery will maintain the date and time settings. However, there is a small
chance the settings may be lost (the backup will last for about 7 days). It is
recommended to check that the date and time settings are still correct after
replacing the battery pack and before shooting or recording of any type.
HINT
About the internal backup battery
i This camera’s internal battery serves to maintain the date and time
settings, as well as the shooting settings. To charge the backup battery,
leave the fully charged battery pack installed in the camera continuously
for about 2 days. In the fully charged state, the backup battery will maintain
the camera settings for about 7 days.
36 VQT3M88
SWITCHING BETWEEN THE RECORDING
MODE AND PLAYBACK MODE
Switch between the recording mode (for recording) and the playback mode
(for viewing your recorded images).
1
2
Turn on the camera (page 32).
Press the REC/ button.
h The mode changes.
h The mode changes each time
the REC/ button is pressed.
REC/
button
VQT3M88 37
MENU SCREEN
Accessing/exiting the Menu Screen
1
2
Set the camera to the recording or playback mode (page 37).
Press the MENU button.
h The Menu Screen appears.
h To cancel the Menu Screen, press the MENU button again.
SET button
Tab
RECORDING MENU 1
1
1080-30p
REC MODE
2
PICTURE SIZE
SCENE MODE
COLOR MODE
FLASH
-
16M
S
3
1
2
3
SELF TIMER
SET
ENTER
Option tab
k To display a different Tab Menu
h The Menu Screen consists of the
Tabs Menu (tabs 1, 2 and 3) and
the Option Tabs Menu (tabs 1, 2
and 3).
h To switch from the active tab menu
to the other tab menu, while the
screen shown above is displayed,
toggle the SET button to the left;
then toggle the SET button up or
down to select the desired tab. The
menu for the selected tab appears.
MENU button
38 VQT3M88
Using the Menu
1
2
Display the desired menu (page 38).
Toggle the SET button up or down to select the item you wish to
change, and press the SET button.
h The Setting Screen for the selected item appears.
h To return to the Menu Screen, press the MENU button.
Select an item to
change
RECORDING MENU 1
Push up
1
2
3
p
REC MODE
PICTURE SIZE
SCENE MODE
COLOR MODE
FLASH
1080-30
16M
-
S
1
2
3
SELF TIMER
ENTER
Applicable mode
PICTURE SIZE
Push down
Press
-
H
16
4608x3456
16M
M
S
-
4608x3456
12
4608x2592[16:9]
2 M 1920x1080[16:9]
2M
M
1600x1200
0.9M 1280x720[16:9]
ENTER
<Setting Screen>
HINT
About the applicable mode indicator
i This indicator shows the shooting mode(s) for which the selected setting is
effective.
i O@: This setting is effective during photo shooting.
i
i
@: This setting is effective during video recording.
@: This setting is effective during photo shooting and video
recording.
O
O
VQT3M88 39
Overview of the Menu Screen
Recording Menu
<Tab 1>
RECORDING MENU 1
1
p
1
2
3
4
5
6
7
REC MODE
1080-30
2
PICTURE SIZE
-
16M
S
3
SCENE MODE
COLOR MODE
FLASH
1
2
3
SELF TIMER
ENTER
1 Recording mode (page 68)
2 Recorded pixels (page 71)
<Photo recording (single-
shot)>
<HD mode>
: Record at 1920 × 1080
pixels (60i).
HX-DC10
: Record at 1920 × 1080
A: Image size is 4608 × 3456
pixels (low compression).
B: Image size is 4608 × 3456
pixels (normal
pixels (30p).
Record at 1280 × 720
:
pixels (60p).
: Record at 1280 × 720
compression).
pixels (30p).
Record at 960 × 540
pixels (30p).
: Image size is 4608 × 2592
pixels (16:9 aspect ratio).
HX-DC1
:
<SD mode>
6: Image size is 4352 × 3264
pixels (low compression).
7: Image size is 4352 × 3264
pixels (normal
: Record at 640 × 480
pixels (30p).
<: Make an audio recording.
compression).
: Image size is 4352 × 2448
pixels (16:9 aspect ratio).
40 VQT3M88
All models
: Image size is 1920 × 1080
pixels (16:9 aspect ratio).
G: Image size is 1600 × 1200
pixels.
: Image size is 1280 × 720
pixels (16:9 aspect ratio).
[: Image size is 640 × 480
pixels.
:Light up both the subject
and the background.
:Shoot in darkened
surroundings, such as at
dusk.
4 Color mode
:Color mode is deactivated.
:Enhanced color saturation.
:Reduce sharpness to
produce a softer image.
:Reduce sharpness and
increase color saturation.
:Skin tones are enhanced.
<Hi-Speed Burst>
HX-DC10
C: 4608 × 3456-pixel
hi-speed burst.
HX-DC1
:Produces a monochrome
(black and white) image.
:Produces a sepia image.
:: 4352 × 3264-pixel
hi-speed burst.
5 Flash
All models
k: The camera will detect the
subject brightness and use
the flash only when
t: 1600 × 1200-pixel
hi-speed burst.
necessary.
3 Scene mode (page 72)
m: The flash will operate with
every image captured
regardless of the
:Scene mode is
deactivated.
:Shoot fast-moving subjects
with less blur.
conditions.
:The flash will not operate
even in dark situations.
:Blur the background to
accentuate the subject in
the foreground.
:Record a clear image of a
subject illuminated by
spotlight.
:Natural looking images in
bright surroundings, such
as in a ski area.
:Vivid blue for sea and sky,
subjects do not appear
dark even in bright sunlight.
:Capture the vibrant reds in
sunrise and sunset shots.
:Record fireworks in the
night sky.
6 Self-timer (page 73)
N: Self-timer is off.
y: Shooting begins 2 seconds
after the [O] button or
[@] button is pressed.
x: Shooting begins
10 seconds after the [O]
button or [@] button is
pressed.
7 Remaining battery power
indication (page 121)
:When recording a
landscape, focus on the
distant subject.
:Beautiful shots of evening
and night scenes.
VQT3M88 41
<Tab 2>
1
RECORDING MENU 2
E.I.S.
1
2
3
4
5
6
7
2
3
FOCUS
FOCUS MODE
METERING MODE
ISO
1
2
3
WHITE BALANCE
ENTER
42 VQT3M88
1 Image stabilizer (page 74)
h Compensate for camera shake
during recording.
5 ISO sensitivity (page 76)
=: Sensitivity is set
automatically
:During video recording, the
image stabilizer is always
active.
:Camera shake in the
captured photo is
*: Sets sensitivity to ISO 50
u: Sets sensitivity to ISO 100
v: Sets sensitivity to ISO 200
w: Sets sensitivity to ISO 400
6: Sets sensitivity to ISO 800
-: Sets sensitivity to ISO 1600
z: Set sensitivity to ISO 3200
(HX-DC10)
corrected.
:Camera shake during video
and photo recording is
compensated for and
corrected.
h The indicated ISO value is the
standard output sensitivity.
:The image stabilizer is not
active.
6 White balance (page 77)
2 Focus (page 75)
>: White balance is
automatically adjusted
depending on the ambient
lighting (auto).
:For shooting in sunny
conditions (sunny).
o: For shooting in overcast
conditions (cloudy).
:For shooting under
incandescent lighting
(incandescent).
h Adjust the focus according to
the distance to the subject.
*: The camera automatically
focuses on the subject with
a range of 10 cm (3.9”) to ∞
(normal).
-: The focus can be set
manually.
:The camera focuses on the
subject within a range of
1 cm (0.4”) to ∞ (macro).
:For setting the most
accurate white balance
(white set).
3 Focus mode
:9-point range finder focus
:Spot focus
A focus mark 'appears in
the center of the LCD
monitor.
7 Remaining battery power
indication (page 121)
4 Metering mode
n: Multi-metering
W: Center-weighted light
measuring
Y: Spot light-measuring
A metering spot @ mark
appears in the center of the
LCD monitor.
VQT3M88 43
<Tab 3>
<HX-DC10>
1
2
RECORDING MENU 3
EXPOSURE
1
2
3
4
5
6
7
P
SUBJECT TRACKING
DIGITAL ZOOM
WIND CUT
3
1
2
3
AUTO REVIEW
SHORTCUTS
1
ENTER
<HX-DC1>
1
RECORDING MENU 3
SUBJECT TRACKING
DIGITAL ZOOM
WIND CUT
2
3
2
3
4
5
6
AUTO REVIEW
SHORTCUTS
1
2
3
1
7
ENTER
44 VQT3M88
1 Exposure (page 78)
(HX-DC10)
5 Auto review
h Specify the duration that the
captured image is shown on
the LCD monitor after the
[O] button is pressed.
@: The exposure is set
automatically.
T: Set the shutter speed
manually (shutter speed
priority).
g: Set the aperture manually
(aperture priority).
H: Set the aperture and
shutter speed manually.
: The image is shown on the
LCD monitor for about 1
second after capture.
: The image is shown on the
LCD monitor for about 2
seconds after capture.
2 Subject tracking (page 80)
h Automatically target a specific
color with the color tracking
function, or capture sharp face
shots with the face tracking
function.
: The image is not shown on
the LCD monitor after
capture.
6 Shortcuts setting (page 82)
h Assign operation shortcuts to
the SET button.
: Enable face tracking.
: Enable color tracking.
:Disable face tracking and
color tracking.
7 Remaining battery power
indication (page 121)
3 Digital zoom
:Enable the digital
zoom.
:Disable the digital
zoom.
4 Wind noise reduction
h Turn ON/OFF the wind noise
reduction function during
video/audio recording.
: Wind noise is reduced.
: Wind noise is not affected.
VQT3M88 45
Playback Menu
<Tab 1>
PLAYBACK MENU 1
1
2
1
2
3
4
5
6
7
SLIDESHOW
PLAY VOLUME
PROTECT
DELETE
1
2
3
ROTATE
RESIZE
ENTER
1 Slideshow (page 86)
h Specify the slideshow settings
4 Delete (page 63)
h Delete files.
and play the slideshow.
5 Rotate (page 89)
2 Play volume
h Rotate a photo.
h Adjust the volume for video
and audio file playback.
6 Resize (page 89)
h A captured image can be
resized to a smaller size and
saved as a separate image.
3 Protect (page 87)
h File protect setting (delete
prohibited)
7 Remaining battery power
indication (page 121)
46 VQT3M88
<Tab 2>
1
PLAYBACK MENU 2
RED-EYE CORRECT.
EDIT VIDEO
1
2
3
2
COPY
1
2
3
4
ENTER
1 Red-eye correction (page 90)
h Repair the “red-eye” caused
by the flash (photos only).
3 Copy (page 100)
h Copy files from the built-in
memory to the card.
2 Edit video (page 91)
h Edit videos.
4 Remaining battery power
indication (page 121)
VQT3M88 47
INTELLIGENT AUTO MODE (HX-DC10)
The following modes (appropriate for the condition) are set just by pointing
the unit to what you want to record.
button
Press the button once to
activate the Intelligent Auto (iA)
mode.
button
i The
icon appears on the
LCD monitor.
i Press it again to cancel the
Intelligent Auto mode.
Mode
Scene
Effect
Portrait
When the subject is
a person
Faces are detected
and focused
automatically, and the
brightness is adjusted
so it is recorded
clearly.
Landscape
Recording outdoors
The whole landscape
will be recorded
vividly without whiting
out the background
sky, which may be
very bright.
*1
*1
Spot light
Low light
Under a spotlight
Very bright subject is
recorded clearly.
Dark room or
twilight
It can record very
clearly even in a dark
room or twilight.
*2
Night
portrait
Recording night
portrait
A subject and the
background are
recorded with near
real-life brightness.
48 VQT3M88
Mode
Scene
Effect
*2
*2
Night
scenery
Recording night
scenery
You can record night
scenery vividly by
slowing the shutter
speed.
Macro
Recording zooming
in on a flower etc.
This allows recording
at very close
proximity to the object
of recording.
*1
*2
Normal
Other situations
Contrast is adjusted
automatically forclear
images.
*1 Video recording only
*2 Photo shooting only
HINT
i Depending on the recording conditions, the unit may not enter the desired
mode.
i Using a tripod is recommended in Night Portrait, Night Scenery and Low
Light modes.
i Faces may not be detected depending on the recording conditions, such
as when faces are of certain sizes or at certain tilts.
VQT3M88 49
k Intelligent Auto Mode
When switching to Intelligent Auto Mode, the Auto White Balance and Auto
Focus operate and automatically adjust the color balance and focusing.
Depending on the brightness of the subject etc., the aperture and shutter
speed are automatically adjusted for an optimum brightness.
i Color balance and focus may not be adjusted automatically depending on
light sources or scenes. If so, manually adjust these settings.
Automatic white balance
The illustration shows the range over which Automatic white balance
functions.
1 The effective range of
Automatic white balance
adjustment on this unit
2 Cloudy sky (rain)
3 Sunlight
4 White fluorescent lamp
5 Halogen light bulb
6 30-minute span just before and
after sunset
10 000K
9 000K
8 000K
7 000K
6 000K
2
3
5 000K
4 000K
4
1
5
3 000K
7 Incandescent light bulb
8 Sunrise or sunset
9 Candlelight
6
7
8
2 000K
1 000K
9
If the automatic white balance is not functioning normally, adjust the white
balance manually. (page 77)
Auto focus
The unit focuses automatically.
i Auto focus does not work correctly in the following situations. Record
pictures in the Manual Focus Mode. (page 75)
h Recording distant and close-up objects at the same time
h Recording a subject through a dirty or dusty window
h Recording a subject that is surrounded by objects with glossy surfaces
or by highly reflective objects
50 VQT3M88
BASIC OPERATION
SHOOTING
BASIC OPERATION/SHOOTING
BEFORE TAKING PICTURES
For best results
Hold the camera securely, keeping your elbows close to your body and
making sure the camera is stable. When zooming in or out, you can minimize
the effects of camera shake by using your other hand on the monitor unit to
help stabilize the camera.
Correct hold
Incorrect hold
A finger is blocking the
lens or flash.
<Holding the camera>
Example 1:
Example 2:
Grip the camera by
wrapping the fingers
of the right hand,
from the little finger
to the middle finger,
around the camera,
and hook the index
finger above the
lens.
Grip the camera by
wrapping the fingers
of the right hand, from
the little finger to the
index finger, around
the camera.
i
To avoid dropping the camera, be sure to attach a handstrap.
Make sure that the lens and flash unit are not blocked by your fingers or the
handstrap. And don’t block the built-in microphone on the monitor unit with
your hand.
<If the camera feels warm...>
i Due to the characteristics of the camera, the outer surface may
become warm during use, but this does not indicate a malfunction.
i If the camera starts to feel uncomfortably hot during use, you might
temporarily discontinue use until it cools down, or try holding it in your
other hand for a while.
Please use a tripod or other support when using the camera for a
long time.
VQT3M88 51
VIDEO RECORDING
1
Turn on the camera (page 32),
and set it to the recording
mode (page 37).
[@] button
h If the subject is a person, a
green double-frame appears
around the face (page 80).
2
Press the [@] button.
h Recording begins.
h It is not necessary to keep the
[@] button pressed while
recording.
h When the remaining recording
time available for the currently
recording video becomes 30
seconds or less, a countdown
of the remaining recording
time appears on the display.
h When the file size of the
current recording exceeds 4
GB, the file is saved once, and
recording begins in a new file.
(4-GB files are automatically
created (page 181).)
Elapsed
recording time
(hours:minutes:
seconds)
h HX-DC1: When the file size of
the recording exceeds 4 GB,
recording pauses (from a few
seconds up to 10 seconds),
and then resumes.
p
001008:0-0300:09
2
M
5
3
End the recording.
h Press the [@] button again
to stop recording.
Available recording
h The elapsed recording time
returns to 000:00:00 each
time recording is stopped.
time remaining
(seconds)
VQT3M88 53
TAKING PHOTOS
1
Turn on the camera (page 32),
and set it to the recording
mode (page 37).
[O] button
h If the subject is a person, a
green double-frame appears
around the face (page 80).
2
Press the [O] button.
1 Press the [O] button
halfway.
h The autofocus operates,
and the image is focused
(focus lock).
2 Continue to gently press
the [O] button all the
way.
h The shutter releases and
the image is captured.
1
2
-
16M
S
F3.5
1/30
h You can view the captured
image on the LCD monitor
by keeping the [O]
Target mark
button depressed when
you capture the image.
For shooting hi-speed burst, see
page 71.
54 VQT3M88
HINT
What is the camera focusing on?
i A target mark &on the LCD monitor
shows the area the camera is
focusing on.
Target mark
-
16M
S
i The camera automatically
determines the correct focus by
measuring from 9 different focus
points within the shooting area. If the
target mark is at a position that is
different from the point you wish to
focus on, you can refocus, for
example, by changing the shooting
angle.
i The large target mark appears when
the camera focuses on a wide area
in the center of the screen.
The focus and exposure can be locked
F3.5
1/2
Camera shake icon
Shutter speed
Aperture
i By assigning an operation shortcut to the SET button (page 82), you can
set the autofocus or the exposure to a fixed setting. When the exposure
setting is fixed, the
autofocus setting is fixed, the
icon appears on the LCD monitor; when the
icon appears on the LCD monitor.
i When the focus setting or scene mode setting (pages 72 and 75) is
changed, the focus lock and AE lock are released.
The shutter speed and aperture are displayed
i The shutter speed and aperture settings are shown on the Recording
Screen.
If the camera shake icon >appears...
i During photo shooting, if the shutter speed is slow and the possibility that
the image may be blurred due to camera shake becomes high, the camera
shake icon may appear on the LCD monitor. In this case, use a tripod to
stabilize the camera when shooting, or set the flash operation mode to
Auto (page 41).
i When shooting with the scene mode function set to the fireworks
mode, the camera shake icon always appears, but this is normal.
Does it seem to take a long time to save images?
i When shooting in dimly lit conditions, it may take some time to save the
data to the card.
Does the image in the LCD monitor appear to waver?
i When the [O] button is pressed halfway, the image in the LCD monitor
may waver vertically. This is the result of internal image processing and is
not a malfunction. This wavering is not recorded and will not affect your
images in any way.
VQT3M88 55
Shoot a photo while recording a video
You can capture a photo (single frame) while recording a video.
1
While recording a video, when you see a scene you’d like to capture
a photo of, press the [O] button.
HINT
i When shooting a photo while recording a video, the flash does not operate.
i The photo stabilizer (page 74) is inoperative.
i When the remaining video recording time becomes approximately
30 seconds, it will no longer be possible to capture a photo while recording
a video. The exact remaining recording time at which this occurs will differ
depending on the subject and on the recording size (page 71), as well as
on the recording mode setting (page 68).
About the recording size of photos
i The size of a photo captured during video recording depends on the video
recording size setting.
Video recording size setting
Photo recording size
(16:9)
(16:9)
(4:3)
[
h It is not possible to capture a photo while recording a video in the
mode.
h It is not possible to shoot hi-speed bursts.
56 VQT3M88
MACRO-PHOTOGRAPHY (ZOOM)
Your camera has two zoom functions: Optical zoom and Digital zoom
(page 45).
1
2
Point the camera lens at the
subject.
Zoom switch
Push the zoom switch toward
[T/]] or [W/P] to compose
the desired image.
[T/]]: Zoom in on the subject.
[W/P]: Zoom out.
h When the zoom switch is
pushed, the zoom bar appears
on the LCD monitor.
3
Take the picture.
For video recording, see page 53.
For shooting photos (single), see
page 54.
For shooting hi-speed bursts, see
page 71.
Zoom bar
When both optical and
digital zoom are enabled
Optical zoom
Digital zoom (blue)
When optical zoom only
is enabled
Pointer
VQT3M88 57
HINT
When recording videos at a high magnification
i When recording videos at a high magnification, a moving subject or
moving camera can cause camera shake, resulting in a distorted playback
image. This phenomenon is due to the characteristics of the MOS sensor
and is not a malfunction.
i It is recommended that you use a tripod to stabilize the camera when
recording videos at a high magnification.
i When the digital zoom is used, the picture quality becomes grainier as the
magnification increases.
i See page 186 regarding zoom magnification.
When the ZOOM RANGE button is pressed... (HX-DC1)
i The magnification is approximately doubled (double-range zoom). Press
the button again to return to normal magnification.
i The [W] icon is shown on the Recording Screen during normal
magnification, and a [T] icon on the double-range zoom Recording Screen.
i Double-range zoom is effective only when recording video. Photos are
recorded without enlargement.
ZOOM RANGE
button
58 VQT3M88
PLAYBACK
BASIC OPERATION/PLAYBACK
PLAYING BACK VIDEOS AND
PHOTOS
1
2
Set the camera to the playback mode (page 37).
Yellow frame
Select the image to play back.
h Toggle the SET button up,
down, left or right to move
the yellow frame to the file
you wish to play back.
h The image information for the
framed image is shown at the
bottom of the LCD monitor.
DEC.20.2011
6:41 PM
100-0006
00:00:05
10.5MB
1080-60i
SET
ENTER
Image
information
3
Press the SET button.
h The image you selected in
step 2 is displayed on the
LCD monitor.
h If a video was selected,
playback begins.
<Photo file: To return to the
screen to select playback
files>
Toggle the SET button down.
HINT
i Photos can be rotated when they
are played back (pages 46 and
89).
i If you close the monitor unit,
playback stops and the camera
switches to the standby mode.
SET button
VQT3M88 59
Video playback operation
To do this...
Do this
Press the SET button or toggle the SET button
up.
During playback, toggle the SET button down.
Normal forward playback
Stop playback
During playback, press the SET button or
toggle the SET button up.
During accelerated playback, toggle the SET
Pause
button up.
To playback
one image
at a time
(single-
frame step)
Duringforward After pausing playback, toggle the SET button
playback
to the right.
During reverse After pausing playback, toggle the SET button
playback to the left.
Duringforward After pausing playback, press and hold the
playback SET button to the right.
During reverse After pausing playback, press and hold the
Slow
playback
playback
SET button to the left.
During forward playback, toggle the SET
button to the right.
Forward
playback
(Maximum
15×)
h
The forward playback speed changes each
time the SET button is toggled to the right.
Toggle the SET button to the left to resume
To
normal playback speed.
During forward playback, toggle the SET
button to the left.
h The reverse playback speed changes each
time the SET button is toggled to the left.
Toggle the SET button to the right to resume
normal playback speed.
accelerate
playback
Reverse
playback
(Maximum
15×)
Return to normal playback
speed
Press the SET button.
During playback, push the zoom switch toward
Louder
Volume
the [T/]] side.
adjustment
During playback, push the zoom switch toward
Softer
the [W/P] side.
60 VQT3M88
HINT
If the
i The
appears on the Playback Screen...
icon appears when playing back a file that was saved in
segments (page 182).
VQT3M88 61
How to save one frame from a video as a photo
1
2
Play back the video. Pause the playback at the point you wish to
“snap” a photo.
Press the [O] button.
h The screen to select the aspect ratio of the photo appears. Select the
desired aspect ratio, and press the SET button. Note, however, that if
the video aspect ratio is 4:3, you cannot select 16:9.
h The latest image number is assigned to the photo when it is saved.
HINT
The file size for a video is very large
i Therefore, be aware that if the video is uploaded to a computer to be
played back, the computer may not be able to play back the video fast
enough, making it appear jerky. (The video will always be displayed
properly on the camera LCD monitor or a television.)
If no audio is heard...
i The audio is not played back when the video is played back in the frame-
by-frame, slow-motion, fast playback or reverse playback mode.
62 VQT3M88
DELETING FILES
Deleted files cannot be restored, so delete files only after carefully checking
the contents.
Delete single/delete all/delete folder
1
Display the Playback Menu 1
(page 38), select the delete
setting, and press the SET
button.
DELETE
DELETE SINGLE
DELETE SELECTED
DELETE ALL
DELETE SINGLE:
Deletes one file at a time.
DELETE SELECTED:
Deletes the selected files
(page 64).
DELETE FOLDER
SET
ENTER
DELETE ALL:
Deletes all files.
DELETE FOLDER:
Delete the folder and all the files in the folder.
2
Select the desired delete mode, and press the SET button.
h The Delete Confirmation Screen appears.
<DELETE SINGLE>
h Toggle the SET button to the left or right to select the file you wish to
delete.
h There is no confirmation screen when deleting single files.
Please make sure that the displayed image is one you wish to
delete.
<DELETE ALL>
h Toggle the SET button to the left or right to confirm the files to delete.
<DELETE FOLDER>
h Toggle the SET button up or down to select the folder you wish to
delete, and press the SET button.
VQT3M88 63
3
Select [DELETE], and press the SET button.
<DELETE SINGLE>
h The currently displayed file is deleted.
h To delete other files, select the files, select [DELETE] and press the
SET button.
<DELETE ALL, DELETE FOLDER>
h The Delete Confirmation Screen again appears. To delete the files,
select [YES] and press the SET button. If [DELETE FOLDER] was
selected, select [YES] again and press the SET button, and the files
will be deleted.
Delete selected
Delete selected files.
1
2
Display the Playback Menu 1 (page 38), select the delete setting, and
press the SET button.
Select [DELETE SELECTED], and
press the SET button.
h The screen to select files to
delete appears.
DEC.20.2011
2:25 PM
100-0006
00:00:25
1080-60i 51.6MB
SET
DELETE
OK
3
Select an image you wish to delete.
h Toggle the SET button left, right, up or down to move the yellow frame
to the file you wish to delete.
64 VQT3M88
4
Press the SET button.
h The selected file is marked with the delete icon [>].
h Up to 100 files can be selected.
h To cancel a delete selection and remove the delete icon from a file,
move the yellow frame to the marked file and press the SET button.
5
6
Press the [O] button or [@] button.
h The Delete Confirmation Screen appears.
Select [YES], and press the SET button.
h The selected files are deleted.
HINT
i Files that are protected from accidental delete cannot be deleted. To delete
protected files, set the protect setting for the files to off (page 87), and then
follow the file delete procedure.
VQT3M88 65
PLAYBACK MODES
21-image display playback
1
2
Display the image you wish to play back.
h The 8-image display appears.
Push the zoom switch toward the
[W/P] side.
h The 21-image display appears.
h While the 21-image display is
shown, you can push the zoom
switch toward the [T/]] side to
change to the 8-image display,
and push it again toward the [T/
DEC.20.2011 2:25 PM
100-0021
]] side to change to the single-
image display.
3
Select the image to play back.
h Toggle the SET button left, right, up or down to move the yellow frame
to the desired image, and press the SET button.
h If the zoom switch is pushed toward the [W/P] side while the 21-
image display is shown, the display changes to the screen to select
the playback folder (page 115).
HINT
Photo playback:
In step 2, press the SET button to display the selected photo on the LCD
monitor.
Video playback:
In step 2, press the SET button to play the selected video.
66 VQT3M88
Magnifying (zooming in) the image (photos only)
Display a photo.
1
2
Push the zoom switch toward the
[T/]] side.
SAVE
105%
h Magnification is enabled.
h The image is magnified, and the
central portion of image is
displayed.
h For a photo that was captured
with the face tracking function
enabled (page 80), the detected
face is in the center of the
magnified image.
SET
Move
100%
h Toggle the SET button left, right,
up or down to view different
parts of the magnified image.
To magnify:
Magnification increases each time the
zoom switch is pushed toward the [T/
]] side.
To return to normal size:
Magnification decreases each time
the zoom switch is pushed toward the
[W/P] side.
h Press the SET button to return to the
normal (100%) view.
HINT
The magnified portion of the image can be saved as a separate image
i Press the [O] button. The magnified portion is saved as a new photo.
i The image size of the saved photo of the magnified portion will be smaller
than that of the original photo.
VQT3M88 67
ADVANCED OPERATION
SHOOTING
ADVANCED OPERATION/SHOOTING
RECORDING MENU 1
To access and use the Menu Screen, see page 38 to 39.
Recording mode setting (page 40)
When recording a video, smoother motion and better image clarity can be
achieved by a higher pixel rate (resolution) and a faster frame rate. However,
the file size will also be proportionately larger, requiring longer times to edit
and store (page 47). It is recommended that you adjust the settings to those
suitable for the desired purpose. Note that this menu is also used for
recording audio only files.
HINT
About recording in the
mode
i Use this mode when using a Mac computer for playing back and editing.
When editing videos...
i In order for videos to be spliced, they must have been recorded in the
same mode.
i Videos that were recorded in different modes cannot be spliced.
Playback of a video that was recorded in the
mode.
i In some cases it may not be possible to play back videos recorded in this
mode even on other devices equipped with this mode.
About the compatibility of recorded videos
i This unit does not support non-MP4-compatible devices. Playback is not
possible on devices that are not MP4 compatible, so please check the
user’s manual for your device to confirm its compatibility.
i In some cases, playback may not be possible on an MP4-compatible
device. In this case, please use the camera for playback.
Concerning recordable time and image quality
i See page 181.
68 VQT3M88
Audio recording and playback
k Recording
1
Select <, and press the SET
button.
Remaining recordable time
h The audio recording mode is
enabled.
h The menu display is canceled if
the MENU button is pressed.
-
S
34106M
014:559:15
2
Press the [@] button.
Elapsed recording time
h Audio recording begins.
h During audio recording, <
appears in the LCD monitor.
h It is not necessary to continue
pressing the [@] button while
recording.
0.3M
000:00:06
h When the remaining recording
time available for the currently
recording video becomes 30
seconds or less, a countdown of
the remaining recording time
appears on the display.
Turns red
3
End the audio recording.
h Press the [@] button again to stop recording.
h The elapsed recording time returns to 000:00:00 each time recording
is stopped.
HINT
You can capture a photo during an audio recording
i Press the [O] button during audio recording to capture a [photo.
Maximum audio recording time?
i
When the recording mode setting is set to audio
<
and the recording exceeds
about 5 hours, the recorded file is saved and the audio recording ends.
i If you close the monitor unit, audio recording stops and the camera
switches to the standby mode.
VQT3M88 69
k Audio playback
1
Select an audio file (: icon), and press the SET button.
h Playback begins.
To do this...
Do this
Start
playback
Press the SET button.
Toggle the SET button up.
Normal
playback
Press the SET button.
Toggle the SET button up.
Pause
Stop
playback
Toggle the SET button down.
During playback, toggle the SET button to
the right.
Fast
forward
Each time the SET button is toggled to the
(Maximum right, the speed increases. If the SET
15×)
button is toggled to the left during fast
forward, the speed decreases.
During playback, toggle the SET button to
the left.
Fast
forward/
fast reverse
Fast
reverse
Each time the SET button is toggled to the
(Maximum left, the speed increases. If the SET button
15×)
is toggled to the right during fast reverse,
the speed decreases.
Pause
Toggle the SET button up.
Return to
normal
playback
Press the SET button.
During playback, push the zoom switch
Louder
Softer
toward the [T/]] side.
Volume
adjustment
During playback, push the zoom switch
toward the [W/P] side.
HINT
If no audio is heard...
i The audio is not played back when the audio recording is played back in
the fast playback or fast reverse mode.
70 VQT3M88
Recorded pixels (page 40)
For photos, you can select either the 4:3 or 16:9 horizontal to vertical aspect
ratio. This menu is also used for shooting hi-speed bursts.
Hi-Speed Burst
1
Select the desired hi-speed burst icon, and press the SET button.
HX-DC10: Select C or t.
HX-DC1: Select : or t.
h The menu display is canceled if the MENU button is pressed.
2
Press the [O] button.
h Shooting begins. Shooting continues as long as the [O] button is
kept pressed.
HINT
What is the maximum number of images in a hi-speed burst sequence?
HX-DC10
C: 8 shots
t: 20 shots
HX-DC1
:: 9 shots
t: 12 shots
i If you continue shooting even after the maximum number of images has
been captured, recording does not stop.
i If you continue shooting after the maximum number of images has been
captured, the photos are saved extending backward from the last photo
captured.
Press the
[O] button.
Release the
[O] button.
During recording, images are temporarily
recorded in the built-in memory.
Perfect shot
Not saved
Images are recorded (maximum number of
images) starting from this point.
VQT3M88 71
When the self-timer is used...
i Shooting stops automatically after the maximum number of images has
been captured.
About the focus when shooting hi-speed bursts
i When a hi-speed burst is captured, the autofocus operates when the [O]
button is pressed halfway, fixing the focus.
Can the flash be used?
i The flash does not operate when shooting hi-speed bursts.
Scene mode setting (page 41)
You can select from various preset settings (aperture, shutter speed, etc.) for
specific shooting conditions.
HINT
i To return to normal photography, select
from the scene mode menu,
and press the SET button.
i A table showing the limitations for settings corresponding to scene mode
icons other than is on page 171.
Scene mode characteristics
Low light mode
iThe shutter speed will be faster than 1/15 sec (when recording video).
Sunset
portrait
/fireworks
modes
/landscape
/night scenery
/night
iWhen shooting a nearby subject, the image may appear blurry.
Fireworks mode
iThe shutter speed is 1/30 sec (when recording video).
iIf shooting in bright surroundings, the image may appear whitish.
Night scenery
/night portrait
modes
iIt is recommended that a tripod be used.
72 VQT3M88
Self-timer setting (page 41)
By assigning an operation shortcut to the SET button (page 82), you can set
the self-timer from the Recording Screen.
HINT
To cancel the self-timer function...
i If the [O] button or [@] button is pressed again before the shutter is
released, the self-timer countdown is canceled.
i For video photography, recording does not stop automatically.
i The self-timer is automatically reset to off N after recording is ended and
the camera turned off.
When x is selected...
i When the [O] button or [@] button is
pressed, the status indicator will blink for
about 10 seconds, and then the image
is captured. Also, the countdown
indication shown in the illustration to the
right appears on the LCD monitor.
When y is selected...
i When the [O] button or [@] button is
pressed, the status indicator will blink
and the indication shown in the
illustration to the right appears on the
LCD monitor to indicate when the
shutter will release.
<2 seconds before>
<1 second before>
Shutter release
VQT3M88 73
RECORDING MENU 2
To access and use the Menu Screen, see page 38 to 39.
Motion compensation (image stabilizer) setting
(page 43)
Your camera can minimize a jittery picture by compensating for unintentional
hand motion.
HINT
If the motion compensation does not seem to be working...
i Due to the mechanical characteristics of this function, it may not be
possible for the camera to compensate for violent motion.
i If the digital zoom (page 45) is being used, the large magnification factor
may make it difficult for the motion compensation function to work correctly.
i When the scene mode function is set to night portrait
, low light
,
night scenery
or fireworks
, the motion compensation effect may
be insignificant.
i When the optical zoom is used or when the autofocus is operating, the
image may appear to waver, but this is not a malfunction.
When motion compensation is enabled,
i The following icons are shown on the LCD monitor:
1080-30p
001:00:05
The video stabilizer is active
The photo stabilizer is active
Both the video stabilizer and the photo stabilizer are active
74 VQT3M88
Focus setting (page 43)
How to use the manual focus
1
Select -, and press the SET
button.
h The focus adjustment bar
appears.
1080-30
p
-
16M
S
340
000:115:17
2
Toggle the SET button to the left
or right to adjust the focus, and
press the SET button.
h The focus is set, and you are
returned to the Recording
Screen.
HINT
About the macro mode
i When the focus range is set to macro
the wide end.
, the zoom is temporarily set to
i By assigning an operation shortcut to the SET button (page 82), you can
change the focus setting from the Recording Screen.
i In some cases it may be difficult for the auto focus to work.
VQT3M88 75
ISO sensitivity setting (page 43)
With the initial settings, the ISO sensitivity is automatically set according to
the brightness of the subject. However, the ISO sensitivity can be set to a
fixed setting.
HINT
i By setting a higher ISO sensitivity, you can set faster shutter speeds and
capture images in darker locations, but noise in the captured images may
increase or the images may be irregular.
i By assigning an operation shortcut to the SET button (page 82), you can
change the ISO setting from the Recording Screen.
76 VQT3M88
White balance setting (page 43)
This camera automatically adjusts the white balance under most lighting
conditions. However, if you want to specify the lighting conditions or change
the overall tone of the image, the white balance can be manually set.
How to use the “white set”
1
2
Fill the entire screen with a plain white card (or piece of paper, etc.).
Select the
icon, and press the SET button.
h This completes the white balance setting.
h The LCD monitor display momentarily goes dark, and then you are
returned to the Recording Menu. If the
icon shows on the
Recording Menu, it indicates that the white balance setting was
completed.
HINT
To cancel the white balance setting
i Select >, and then press the SET button.
If the color or brightness of the screen changes, if bands appear on the
screen, or if the LCD monitor flickers during indoor photography...
i When shooting under fluorescent lighting, sodium-vapor lighting, mercury
lighting, etc., the color and/or brightness of the screen may change, or
horizontal bands may appear across the screen. This is not a malfunction.
Reset the white balance in the following cases.
h When there is a change in the lighting, or the recording location is
changed
i If the colors in the image are not correct, confirm that the white balance
setting matches the actual light source.
VQT3M88 77
RECORDING MENU 3
To access and use the Menu Screen, see page 38 to 39
Exposure setting (HX-DC10) (page 45)
The shutter speed and aperture size can be set individually.
1
Select the desired icon from the
exposure menu, and press the
SET button.
<If T, g or , was
selected>
1 If , is selected, toggle the
SET button up or down to
select aperture value or
shutter speed.
F3.5
1/1000
2 Toggle the SET button to the
left or right to change the
setting for the selected
parameter.
Shutter speed
Aperture
<Setting ranges>
Aperture: F3.5 to F8.0
Shutter speed: 2S (2 sec) to 1/1500 (1/1500 sec)
* When the aperture is other than F8.0, the shutter speed range is 2S
to 1/1000.
* When the aperture priority g is set to F8.0, the shutter speed range
is 2S to 1/1500.
* Depending on the zoom magnification, the aperture value (F-number)
may not be displayed.
2
Press the SET button.
h This completes the exposure setting.
78 VQT3M88
HINT
i To prevent the effects of camera shake at slow shutter speeds, it is
recommended to use a tripod or other method to stabilize the camera.
i A slow shutter speed may be useful for taking pictures in a darker
environment, but noise in the image may be increased.
i If the exposure setting is set to T, g or H, by assigning an operation
shortcut to the SET button (page 82), you can select the T, g or H
exposure setting from the Recording Screen.
i The exposure setting automatically becomes @ if the scene mode
function is active.
When shooting a hi-speed burst...
i The shutter speed will be faster than 1/30 sec.
When recording a video...
i Even if the shutter speed is set to slower than 1/29 sec, the shutter speed
will be 1/30 sec.
VQT3M88 79
Subject tracking settings (page 45)
Adjust the settings to automatically target a specific color with the color
tracking function, or capture sharp face shots with the face tracking function.
Shooting with the face tracking function
1
Set the face tracking setting to
.
h When the face tracking function is activated, a double green frame
appears superimposed on the face in the center of the LCD monitor.
h Each of the other faces is framed by a single green frame.
<When shooting photos: HX-DC10/HX-DC1>
2
3
Press the [O] button halfway.
h The double green frame changes to orange.
Press the [O] button.
h Gently press the [O] button all the way to capture the photo.
<When recording videos: HX-DC10>
2
Press the [@] button.
h Recording begins.
HINT
About recording with the subject tracking
i The tracking function may not work when the subject in the LCD monitor is
relatively small or appears dark.
i If the scene mode function setting was fireworks
night scenery , it automatically changes to
i The focus mode changes to 9-point range finder
, landscape
or
.
, and the metering
mode changes to multi n.
80 VQT3M88
Shooting with the color tracking function (photos
only)
1
2
Set the color tracking setting to
h A target mark (+) appears in the center of the LCD monitor.
.
Move the target mark to the desired subject, and press the SET
button.
h When the subject is successfully targeted, a target frame icon (blue
ꢀ) appears superimposed on the subject.
<To cancel the color tracking operation>
h While the target frame icon is displayed, press the SET button.
<If the subject is not successfully targeted>
h The target frame icon (red ꢀ) continues to be displayed. Press the
SET button once more, and try to engage the target again.
3
Press the [O] button.
h The image is captured at the moment the [O] button is pressed.
HINT
If the target frame turns red...
i The target frame turns red if it has lost track of the subject. It will turn blue
when the subject is successfully targeted again.
VQT3M88 81
Shortcut setting (page 45)
Assign functions (operation shortcuts) to the SET button when it is toggled
up, down, left or right when the Recording Screen is displayed.
1
Select [SHORTCUTS], and
press the SET button.
: Assign the function when the
SET button is toggled up.
: Assign the function when the
SET button is toggled down.
: Assign the function when the
SET button is toggled to the
left.
SHORTCUTS
OFF
OFF
OFF
RECOMMENDED SETTINGS
SET
ENTER
: Assign the function when the
SET button is toggled to the
right.
SET button
RECOMMENDED SETTINGS:
The most commonly used
settings are automatically
assigned.
2
Select the SET button operation to which you wish to assign the
function, and press the SET button.
h The screen to assign a function to the key appears.
AF LOCK: Lock the focus (page 55).
AE LOCK: Lock the exposure setting (page 55).
FOCUS: Set the focus (page 75). (This operation shortcut can be
assigned only to the
or
key.)
m FLASH: Set the flash operation (page 41).
) EXP COMPENSATION: Adjust the exposure (page 85).
s ISO:
Set the ISO sensitivity (pages 43 and 76).
O SELF TIMER: Set the self-timer (page 73).
H EXPOSURE: Set the exposure value for the exposure setting
(page 78) (HX-DC10).
PHOTO VIEW: Select the desired field of view (photo view or video
view) for the Recording Standby Screen display.
When “photo view” is selected, a frame to show the
field of view during video recording appears.
OFF: No operation shortcut is assigned to the key.
82 VQT3M88
Video recording area
<Photo view>
<Video view>
3
4
Toggle the SET button up or down.
h Display the function you wish to assign to the key.
Press the SET button.
SHORTCUTS
h The selected function is
assigned to the key, and you are
returned to the Shortcuts
Screen.
h To assign functions to the other
keys, repeat steps 2 through 4.
PHOTO VIEW
FOCUS
FLASH
SELF TIMER
RECOMMENDED SETTINGS
SET
ENTER
<When [RECOMMENDED
SETTINGS] is selected>
VQT3M88 83
5
Press the MENU button.
h The screen to confirm the
shortcut settings appears, and
then you are returned to the
Recording Menu.
SHORTCUTS
h This completes the shortcuts
setting.
<To confirm the assigned
shortcuts>
h On the screen in step 1, press
the MENU button, and the
screen to confirm the shortcut
settings appears.
84 VQT3M88
Exposure compensation
By assigning the exposure compensation operation shortcut to the SET button
(page 82), you can make the image lighter or darker when capturing images.
1
2
Assign the operation shortcut to
the SET button (page 82).
1080-30
p
-
16M
S
340
000:15:17
Press the SET button to which
the operation shortcut was
assigned.
h
The exposure compensation bar
appears.
0.0
3
Toggle the SET button to the left
or right to adjust the exposure.
Pointer
Exposure compensation bar
h
The exposure compensation
numerical value is shown at the
left end of the exposure
compensation bar.
h
h
The exposure compensation
can be set to a value from
–1.8 to +1.8.
The exposure compensation bar
is canceled when the MENU
button or the SET button is
pressed.
HINT
The exposure compensation setting is canceled in the following cases:
i
i
i
i
i
i
i
When the pointer is set to 0.0.
When the camera is set to the playback mode.
After the power is turned off.
When the camera is set to the standby mode.
When the scene mode is changed.
When the USB cable is inserted or removed.
Intelligent Auto mode is activated or deactivated (HX-DC10).
VQT3M88 85
PLAYBACK
ADVANCED OPERATION/PLAYBACK
PLAYBACK MENU 1
To access and use the Menu Screen, see page 38 to 39.
Slideshow settings (page 46)
Specify the settings for playing back files continuously in a “slideshow” format.
In a slideshow of photos, you can set the transition time, transition effects and
BGM.
Changing a setting
1
Select the item you wish to
change, and press the SET
button.
SLIDESHOW
MODE
ALL
SHORT
SLIDES INTERVAL
EFFECT SETUP
MUSIC SELECT
START
2
3
Toggle the SET button up or
down to change the setting.
OFF
SET
ENTER
Press the SET button.
Begin the slideshow
1
Select [START] and press the SET button.
h Slideshow playback begins.
h To stop slideshow playback, press an operation button. (Playback also
stops if the zoom switch is pushed.)
HINT
BGM for videos?
i When videos are played back in a slideshow, the recorded audio track is
played back; the BGM is not played.
BGM volume?
i Adjust the volume before beginning the slideshow (page 46).
86 VQT3M88
File protect setting (page 46)
Prevent accidental erasure of image and audio files.
Protect files one by one
1
Display the file that you want to protect from accidental erasure, and
display the Playback Menu 1 (page 38).
2
3
Select [PROTECT] and press the SET button.
Select [PROTECT SINGLE] and
press the SET button.
h [LOCK] appears.
PROTECT
h If the protect mode has already
been enabled for the file, then
[UNLOCK] appears.
LOCK
RETURN
SET
ENTER
4
Select [LOCK] and press the SET
button.
h The protect mode is set for the
file.
h The protect mark
indicates
that the file is locked.
HINT
i Even if the protect mode is set for certain files, they will be deleted if the
card is reformatted.
To select a different image in step 3...
i Toggle the SET button to the left or right.
To cancel the protect mode for a file...
i Display the desired file and repeat steps 1 to 3, select [UNLOCK], and
press the SET button. The protect mark
mode is canceled.
will disappear and the protect
VQT3M88 87
Protect selected files
Select multiple files to protect.
1
2
3
Display the Playback Menu 1 (page 38).
Select [PROTECT] and press the SET button.
Select [PROTECT SELECTED]
and press the SET button.
h Toggle the SET button left, right,
up or down to move the yellow
frame to the file you wish to
protect.
DEC.20.2011
1080-60i
2:25 PM
100-0006
00:00:25
51.6MB
SET
LOCK
4
Press the SET button.
h The selected file is marked with the protect icon
.
h To cancel a protect selection and remove the protect icon from a file,
move the yellow frame to the marked file and press the SET button.
88 VQT3M88
Rotate (page 46)
Captured photos can be rotated to the correct orientation for viewing.
HINT
i An image for which the protect mode has been enabled cannot be rotated.
To rotate a protected image, cancel the protect mode before beginning the
rotate image procedure (page 87).
Resize (page 46)
A captured image can be resized to a smaller size and saved as a separate
image.
You can set the size to 1600×1200 pixels or 640×480 pixels.
The latest image number is assigned to the photo when it is saved.
HINT
Why can’t the image be resized?
i An image can be resized only to a smaller (or the same) size, not to a
larger size.
VQT3M88 89
PLAYBACK MENU 2
To access and use the Menu Screen, see page 38 to 39.
Correcting red-eye (page 47)
Repair the red-eye effect in photos to make the eyes appear more natural.
In the case of [SAVE AS NEW], the latest image number is assigned to the
photo when it is saved.
HINT
If the “Red-eye correction not successful” message appears...
i The camera was not able to successfully repair the image.
i
The correction function works to automatically edit flaws that the camera
detects in captured images. In some cases, the camera may fail to correctly
repair a flaw.
90 VQT3M88
Editing videos (page 47)
You can trim away unwanted portions from a video and save it as a new video
(video trimming [extracting]). You can also join videos together and save them
as one separate clip (“splicing”).
Procedure to trim (extract) a portion of a video
1
2
Specify the frames
(1, 2) where the
video is to be split.
A
B
C
J
Extract the specified portion.
[Two ways to split the
video]
i Trim away portions
A and C, and save
portion B.
i Delete portion B,
and join portions A
and C.
i The original
video is not
affected.
(You can also choose to erase the original video when the new is saved.)
VQT3M88 91
Procedure to splice videos
Specify the video that will come first.
J
Specify the video clip that you wish to
append (splice).
J
Splice the videos.
i The videos are spliced.
i
The original videos are not affected.
(You can also choose to erase the
original videos when the new video is
saved.)
When editing videos...
i When editing videos, do not turn off the camera, as doing so may erase
the original video.
i As the number or size of the videos increases, the card memory may
become full, making it impossible to edit or save the videos. In this case,
you will need to free some of the memory on the card by deleting files that
are no longer necessary (pages 46 and 63).
92 VQT3M88
Video trimming (extracting)
1
2
Select the video to be trimmed from the 8-image display.
h Move the yellow frame to the video you wish to trim (page 59).
Display the Playback Menu 2
(page 38), select [EDIT VIDEO],
and press the SET button.
EDIT VIDEO
SPLIT
SPLICE
SET
ENTER
3
Select [SPLIT] and press the SET
button.
h The Split Screen appears.
Start point
SPLIT
00:00:10
SAVE
VQT3M88 93
4
Specify the start point of the extract.
h Play the video until approximately the desired point, pause the video
then play the video one frame at a time, stopping at the start point of
the extract. This will be the first frame of the extract.
h If the start point of the video is also the start point of the extract,
proceed to step 5.
<Procedure>
Play:
After pausing playback, press and hold the SET button to the right for
about 2 seconds for forward playback, or to the left for reverse
playback.
Pause:
During playback, press the SET button.
Accelerated playback:
During playback, toggle the SET button to the left or right to change
the playback speed.
Single frame:
After pausing playback, toggle the SET button to the right to move
forward one frame, or to the left to move back one frame.
94 VQT3M88
5
Toggle the SET button up.
h The start point of the video
extract is set, and the screen to
specify the end point appears.
h Specify the end point of the
extract by following the same
procedure as in step 4.
Approximate playback time
SPLIT
00:00:06
<When joining the first and latter
portions>
1 Toggle the SET button down.
h Each time the SET button is
toggled down, the sections to
delete and the sections to
save are reversed.
SAVE
End point
Portion to be deleted (Black)
2 Specify the end point of the
extract. The frame following the
end point of the extract will be
the start point of the latter portion
to be joined.
6
Press the [O] button or [@ ]
button.
SPLIT
h A screen appears for you to
select either to save the edited
video as a new (separate) file, or
to delete the original video and
replace it with the edited video.
SAVE AS NEW:
The edited video will be saved as
a new file. The original video
remains unchanged.
SAVE AS NEW
OVERWRITE
REVIEW CLIP
SET
ENTER
OVERWRITE:
The original video will be deleted.
Only the edited video will be
saved.
REVIEW CLIP:
Play back the edited video before
saving it.
VQT3M88 95
7
Select the desired option, and press the SET button.
h Editing starts.
h When editing videos, do not turn off the camera, as doing so may
erase the original video.
h When editing ends, you are returned to the Playback Menu.
HINT
i You will not be able to overwrite the file if the original file is protected.
i If the “CARD FULL.” or “Built-in Memory full.” message appears, you will
need to free some of the memory by deleting files that you do not need to
keep.
i Audio files cannot be trimmed.
Playback volume?
i Adjust the volume before beginning editing (page 60).
In case of prolonged recording...
i During the editing of lengthy videos, the time to process the large amount
of data can become quite long. To avoid problems caused by the battery
pack becoming depleted in the middle of video editing, before starting to
edit be sure that a sufficiently charged battery pack is installed in the
camera, or connect the AC adaptor.
i It is recommended that a computer (HD Writer VE 1.0) be used to edit long
videos.
i Videos shorter than 1 second cannot be edited.
96 VQT3M88
Splicing (joining) videos
HINT
i Videos that were recorded in different modes cannot be spliced.
1
2
3
Display the Playback Menu 2
(page 38), select [EDIT VIDEO],
and press the SET button.
EDIT VIDEO
SPLIT
SPLICE
SET
ENTER
Select [SPLICE] and press the
SET button.
h The 8-image playback display for
videos appears.
DEC.20.2011 8:53 PM 100-0016
00:00:05
1080-60i
SET
SAVE
OK
Move the yellow frame to the
video you wish to splice, and
press the SET button.
Assigned number
h The specified video is labeled
with a number.
1
h Up to 9 videos can be selected.
h The splice order follows the
order in which the numbers are
assigned.
h To cancel a selection and
remove the number label from a
video, select the video and press
the SET button.
DEC.20.2011 8:53 PM 100-0016
00:00:05 00:00:05
1080-60i
SET
SAVE
UNLOCK
Approx. playback time
VQT3M88 97
4
Press the [O] button or [@]
button.
SPLICE
h A screen appears for you to
select either to save the spliced
video as a new (separate) file, or
to delete the original videos and
replace them with the joined
video.
SAVE AS NEW
OVERWRITE
REVIEW CLIP
SET
ENTER
SAVE AS NEW:
The spliced video clip will be saved
as a new file. The original videos
remain unchanged.
OVERWRITE:
The original videos will be deleted.
Only the joined video will be saved.
REVIEW CLIP:
Play back the spliced video before
saving it.
5
Select the desired option, and press the SET button.
h Editing starts.
h When editing videos, do not turn off the camera, as doing so may
erase the original video.
h When editing ends, you are returned to the Playback Menu.
98 VQT3M88
HINT
i If the file size of the video after editing exceeds 4 GB, it is not possible to
either “SAVE AS NEW” or “OVERWRITE”.
i You will not be able to overwrite the file if the original file is protected. If you
want it to be erased, you will need to first remove the protection (page 87).
i If the “CARD FULL.” or “Built-in Memory full.” message appears, you will
need to free some of the memory by deleting files that you do not need to
keep.
i Audio files cannot be spliced.
Playback volume?
i Adjust the volume before beginning editing (page 60).
In case of prolonged recording...
i During the editing of lengthy videos, the time to process the large amount
of data can become quite long. To avoid problems caused by the battery
pack becoming depleted in the middle of video editing, before starting to
edit be sure that a sufficiently charged battery pack is installed in the
camera, or connect the AC adaptor.
i It is recommended that a computer (HD Writer VE 1.0) be used to edit long
videos.
VQT3M88 99
Copy (page 47)
Files can be copied from the built-in memory to the SD card.
1
2
Display Playback Menu 2, select [COPY], and press the SET button.
h The Copy Screen appears.
Select the desired option, and press the SET button.
[COPY SINGLE]: Copy files one at a time.
[COPY SELECTED]: Copy selected files (page 101).
[COPY ALL]: Copy all the files.
<If [COPY SINGLE] was selected>
h Toggle the SET button left or right to select the file you wish to copy.
h Proceed to step 3.
<If [COPY ALL] was selected>
h Press the SET button to begin copying.
h When copying is completed, you are returned to the Playback Menu.
3
Select [COPY], and press the SET button.
h Copying begins.
h To continue copying files, toggle the SET button left or right to display
the desired file to copy, select [COPY], and press the SET button.
100 VQT3M88
Copying selected files
Copy multiple selected files.
1
2
3
Display Playback Menu 2, select [COPY], and press the SET button.
h The Copy Screen appears.
Select [COPY SELECTED], and press the SET button.
h The screen to select files appears.
Toggle the SET button left, right, up or down to move the yellow
frame to a file you wish to copy, and press the SET button.
h A checkmark is superimposed on the selected file.
h To deselect a file, move the yellow frame to the file, and press the SET
button.
4
Press the [O] button or [@] button.
h Copying begins.
h When copying is completed, you are returned to the Playback Menu.
HINT
i To make optimum use of the capacity of the SD card or built-in memory,
you can select specific portions of videos to copy by using the video
trimming feature (page 93).
VQT3M88 101
FILE INFO DISPLAY
You can check what the settings were when a file was recorded with your
camera.
1
2
Set the camera to the playback mode (page 37).
Select the image for which you wish to display the information.
h Toggle the SET button up, down, left or right to move the yellow frame
to the file you wish to play back.
3
Press the MENU button for
2
100-0001
at least 1 second.
h The Information Screen
appears.
h If the MENU button is
pressed again, the
Information Screen is
canceled.
3
4
5
B
p
1080-30
1
7.3MB
1920x1080 30p
00:00:03
MPEG-4 AVC/H.264
9
DEC.20.2011 7:30 PM
1 Recording mode/
0
1
recorded pixels
settings
2 Image or sound
number
3 Protect setting
4 File size
5 Video or audio
recording time
6 Exposure
compensation setting
7 Aperture value
8 Shutter speed
9 Remaining battery
charge
0 Date and time of image
A ISO sensitivity setting
B Indicates location of
saved file (SD card or
built-in memory)
<Video file>
8
100-0002
987KB
2
3
4
7
B
6
A
9
2
M
1600x1200
IRIS
F3.5
SHUTTER
EXPOSE
ISO
1/125
+0.3
400
DEC.20.2011 7:30 PM
0
1
<Photo file>
2
3
4
5
B
100-0003
250KB
00:00:03
AAC
9
DEC.20.2011 7:30 PM
0
<Audio file>
102 VQT3M88
OPTION SETTINGS
OPTION SETTINGS
DISPLAY THE OPTION SETTING
MENU
The camera settings are executed via the Option Setting Menu.
1
Turn on the camera, and press
the MENU button.
RECORDING MENU 1
REC MODE
1
2
3
1080-30
p
PICTURE SIZE
SCENE MODE
COLOR MODE
FLASH
-
16M
S
1
2
3
SELF TIMER
SET
ENTER
Option tab
2
Select an Option tab (1, 2 or 3).
h The Option Setting Menu
appears.
h If you toggle the SET button to
the right, the screen to select a
setting to change appears.
OPTION MENU 1
CLOCK SET
ALERT SOUND
DISPLAY
1
2
3
ECONOMY
1
2
3
BRIGHTNESS
ENTER
To access a Setting Screen
3
Toggle the SET button up or down to select the item you wish to set,
and press the SET button.
h The Setting Screen for the selected item appears.
h To return to the Menu Screen, press the MENU button.
VQT3M88 103
1 CLOCK SET setting (page 34)
h Set the camera’s clock.
2 ALERT SOUND setting
h Settings for the types and
volume of the camera’s
operation sounds.
4 ECONOMY setting (page 33)
h Specify the elapsed period of
inactivity before the sleep
mode (to conserve battery
power) is activated.
BATTERY: REC:
TURN ON/OFF:
Set the elapsed time before
the sleep mode is activated
in the recording mode when
using power from the battery.
BATTERY: PLAY:
Mute or enable the sounds
when the camera is turned
on or off.
SHUTTER:
Select the sound that is
produced when the [O]
button is pressed.
Set the elapsed time before
the sleep mode is activated
in the playback mode when
using power from the battery.
AC: REC/PLAY:
Set the elapsed time before
the sleep mode is activated
in the recording or playback
mode when using power
from the AC adaptor.
KEY SW:
Select the sound that is
produced when the SET
button, MENU button, etc.
are pressed.
OPERATION VOL:
Adjust the volume of the
operation sounds.
ALL OFF:
The operation sounds are
disabled.
5 BRIGHTNESS setting
h Adjust the brightness of the
camera’s LCD monitor display.
6 Remaining battery charge
OPERATION SOUNDS ON:
The operation sounds are
enabled.
display (page 121)
3 DISPLAY setting
h Specify the information to
display on the LCD monitor.
ON:
Display the capture date and
playback time (videos).
OFF:
Do not display the capture
date or playback time.
VQT3M88 105
Tab 2
OPTION MENU 2
LANGUAGE
TV OUTPUT
INITIAL SET
FORMAT
1
2
3
1
2
3
4
1
2
3
ENTER
5
106 VQT3M88
1 LANGUAGE setting
h Select the language in which
the LCD monitor messages
are displayed.
2 TV OUTPUT setting (page 110)
3 INITIAL SET
h Reset the camera settings to
the factory-preset settings.
h The following settings do not
change with this procedure:
Date and time setting
Language setting
4 FORMAT (page 118)
FORMAT:
Logical format of the SD
card or the built-in memory is
executed.
DELETE DATA:
Physical format of the SD
card or the built-in memory is
executed.
5 Remaining battery charge
display (page 121)
VQT3M88 107
Tab 3
OPTION MENU 3
REC FOLDER
1
2
3
1,2
3
FILE NO. CONT'D
1
2
3
ENTER
4
108 VQT3M88
TV output setting (page 107)
Specify the type of image signal that is output from your camera’s USB/AV
terminal.
1
Select [TV OUTPUT], and press
the SET button.
TV SYSTEM:
TV OUTPUT
Set the type of TV signal that is
output from the USB/AV terminal.
TV ASPECT:
Set the TV’s aspect ratio.
HDMI:
TV SYSTEM
NTSC
16:9
TV ASPECT
HDMI
AUTO
ON
VIERA Link
Set the signal that is output from
the HDMI terminal.
SET
ENTER
VIERA Link:
Set the VIERA Link function.
2
Select the desired setting, and press the SET button.
h The screen to change the parameter for the selected setting appears.
<If [TV SYSTEM] is selected>
NTSC: Outputs NTSC video signals.
PAL: Outputs PAL video signals.
<If [TV ASPECT] is selected>
16:9: Use this setting when a TV having an aspect ratio of 16:9 is
connected.
4:3: Use this setting when a TV having an aspect ratio of 4:3 is
connected.
<If [HDMI] is selected>
AUTO: The camera automatically determines the appropriate setting.
720p: Choose this setting if the video was recorded in the
or
mode.
1080i: Choose this setting if the video was recorded in the
or
mode.
480p: Choose this setting if the video was recorded in the
mode.
h Does not work with 480i connector.
110 VQT3M88
<If [VIERA Link] is selected>
ON: Use the VIERA Link.
OFF: Do not use the VIERA Link.
3
4
5
Toggle the SET button up or down to select the desired parameter.
Press the SET button.
Press the MENU button 2 times.
h This completes the TV output setting.
VQT3M88 111
Relation between [TV ASPECT] setting and TV
display
The tables below show the video signal that is output when the [TV ASPECT]
setting is changed. However, note that for some TVs that have an auto-detect
function, the output may not conform to the table, or the TV display may not
change at all.
[TV
ASPECT]
setting
TV type to be
connected
Image file to be
displayed
TV display
Photo
(4:3)
4:3
4:3
Video in SD mode
Video in HD mode
112 VQT3M88
[TV
ASPECT]
setting
TV type to be
connected
Image file to be
displayed
TV display
Photo
(4:3)
16:9
16:9
Video in SD mode
Video in HD mode
HINT
If the TV display is not correct…
i If the appearance of the image on the TV monitor is not correct, you can
either change the camera’s [TV ASPECT] setting, or change the screen
size setting on your TV. To change the screen size setting on your TV,
please refer to the instruction manual for your TV.
The aspect ratio of the output photo does not change to 16:9?
i The photo output will be 4:3 for images captured in the 4:3 photo mode.
VQT3M88 113
Storage folder setting (page 109)
Create or select a recording folder (a folder in which to store recorded files).
1
2
Set the camera to the recording mode, and display the Option
Setting Menu.
Select [REC FOLDER], and
press the SET button.
<Create a new folder>
h Select [CREATE NEW
FOLDER].
REC FOLDER
CREATE NEW FOLDER
100CDPFP
<Select an existing folder>
h Select the desired folder
number.
SET
ENTER
3
Press the SET button.
h This completes the create/select folder setting.
h If you created a new folder, it automatically becomes the selected
recording folder.
HINT
When an existing folder cannot be selected or a new one created...
i A folder cannot be selected if it was created using a different device, or if it
already contains the maximum number of files.
114 VQT3M88
Playback folder setting (page 109)
If the card contains multiple folders, you can select from which folder you
would like to play back.
1
2
Set the camera to the playback mode, and display the Option Setting
Menu.
Select [PLAYBACK FOLDER] and
PLAYBACK FOLDER
press the SET button.
100CDPFP
101CDPFP
102CDPFP
ENTER
3
Toggle the SET button up or down to select the desired playback
folder, and press the SET button.
h The files in the selected folder are displayed in the Playback Screen.
VQT3M88 115
File No. continued setting (page 109)
<File number continued function [OFF]>
If a newly formatted card is used, the file name (image number) of the
captured image automatically begins from 0001. If the card is subsequently
reformatted, or if a different reformatted card is used, the file names again
begin from 0001.
File name (image number)
Card A
0001, 0002......0012, 0013
Replace card
Card B
0001, 0002......0012, 0013
<File number continued function [ON]>
By setting the file number continued function to [ON], even if the card is
reformatted or the card is replaced with another card, the consecutive
numbering of file names continues from the last number recorded by the
camera.
File name (image number)
Card A
0001, 0002......0012, 0013
Replace card
Card B
0014, 0015....... 0025, 0026
116 VQT3M88
i If Card B already has files in it when it replaces Card A, file names are
assigned as follows.
When the highest file number on Card B (before replacing) is lower
than the highest file number on Card A: the file name of the next
recorded image continues from last file name recorded on Card A.
Card A
0001, 0002 ..... 0012, 0013
Replace card
Card B
0001, 0002, 0014, 0015 ..... 0025, 0026
Previously recorded files
When the highest file number on Card B (before replacing) is higher
than the highest file number on Card A: the file name of the next
recorded image continues from last file name recorded on Card B.
Card A
0001, 0002 ..... 0012, 0013
Replace card
Card B
0020, 0021, 0022, 0023 ..... 0025, 0026
Previously recorded files
HINT
When the built-in memory is used...
i If the file number continued function is [ON], file name numbering
continues just the same as when an SD card is used, even if the built-in
memory is formatted or the medium is switched to the SD card.
At the end of a photography session...
i Until the file number continued function is set to [OFF], consecutive file
names are assigned.
VQT3M88 117
Formatting (initializing) (page 107)
A card must be formatted with this camera:
i After purchasing, when used for the first time, or
i If it was formatted using a personal computer or other device.
The card cannot be formatted if the lock switch is set to the “LOCK” position.
Proceed with the format procedure after setting the lock switch to the
unlocked position (page 19).
HINT
Caution during formatting
i Do not turn off the power to the camera or eject the card during formatting.
Formatting the card erases the files
i When a storage medium is formatted, all recorded files on the medium are
erased. Protected data (page 87) is also erased, so before formatting a
card, any data you want to keep should be copied to your personal
computer’s hard disk or other storage medium.
When disposing of or transferring the SD card, execute the [DELETE
DATA] procedure from the Format Menu
i If a card is reformatted or the data is erased from the card using the
camera or a computer, the card’s control data may be merely modified and
the data itself may not be completely erased from the card.
i In some cases it may be possible to recover the data from a reformatted
card using special software for that purpose. However, if the camera is
used to erase data, it will be impossible to recover the data even by the use
of data recovery software.
i If you are disposing of a card, it is recommended that you physically
destroy it. If you are transferring the card to someone else to use, it is
recommended that you use the camera to erase the data, or use
commercially available software for erasing card data. Managing data is
the responsibility of the user.
Can’t select [DELETE DATA]?
i Use the AC adaptor to power the camera. [DELETE DATA] cannot be
selected when the battery is used to power the camera.
118 VQT3M88
CHECKING THE REMAINING CARD
MEMORY
You can check how many images can be captured, how much video recording
time and how much audio recording time is available on the card. For a table
showing the recording capacities of SD cards, please see pages 181 to 184.
Checking the remaining number of images and
video recording time
1
Set the camera to the recording
mode (page 37).
h The remaining number of images
appears in the upper left of the
LCD monitor.
h The remaining video recording
time appears in the upper right of
the LCD monitor.
Remaining number of images
1080-30
p
-
16M
S
374
000:16:51
h The remaining number of images
and video recording time will
differ depending on the resolution
and compression settings.
Remaining video
recording time
VQT3M88 119
Check the available audio recording time
1
Set the camera to the audio
Remaining audio recording
recording mode (page 69).
h The remaining audio recording
time is shown.
time
M
3740.3
016:30:36
HINT
i When the remaining number of images or the remaining video recording
time is “0”, you cannot capture any more images. To capture more images,
either install a new card, or save the images to a computer and then delete
them (pages 46 and 63) from the card.
i Even when the remaining number of images or the remaining video
recording time becomes “0”, it may be possible to continue recording by
changing the recording size, recording mode, or recorded pixels setting
(pages 40, 68 and 71).
i The display of the remaining number of images, video recording time or
audio recording time may not be precise.
120 VQT3M88
CHECKING THE REMAINING
BATTERY PACK CHARGE
When using the battery pack, the remaining battery pack charge can be
checked on the LCD monitor. Make sure to check this indicator before
capturing an image. For an indication of the possible length of time for battery
pack operation, see page 23.
1
Display the Recording Menu or
Playback Menu (page 38).
h The battery pack remaining
charge indicator appears in the
lower right corner of the LCD
monitor.
h Due to the battery pack
characteristics, when the
ambient temperature is low,
may appear early for an
RECORDING MENU 1
REC MODE
1
2
3
1080-30p
PICTURE SIZE
SCENE MODE
COLOR MODE
FLASH
-
16M
S
1
2
3
SELF TIMER
ENTER
Battery pack remaining
charge indicator
incorrect indication of the
remaining charge.
Also, depending on the
1080-30p
000:00:09
2
M
conditions of use of the camera
or the ambient conditions
(temperature, etc.), the indicated
remaining charge may change.
Therefore, this indication can
only be used as a general
approximation of the remaining
charge.
h When the battery charge is low,
the battery pack remaining
charge indicator also appears on
the screen during recording.
Battery pack remaining
charge indicator
VQT3M88 121
Battery pack
remaining
charge indicator
Battery remaining charge
Approx. full.
Power is low.
It will soon be impossible to capture or play
back images.
Recharge the battery pack.
HINT
i If any file is present, you can also check the remaining battery pack charge
on the file information display (page 102).
i Battery life may differ even among battery packs of the same type.
i Depending on the usage of the camera (such as the number of times the
flash is used, the use of the LCD monitor, etc.) or the ambient temperature
(temperatures below 10 °C [50 °F]), the number of images that can be
saved on a fully charged battery pack will vary greatly.
i It is recommended that you prepare an extra battery pack(s) when taking
pictures at a wedding or while traveling, for example, so you don’t miss
capturing images of important moments due to the battery pack power
running out. The same is recommended for taking photos in cold
environments. (In a ski area, for example, the battery pack can be kept
warm in your pocket until ready to use.)
122 VQT3M88
OTHER DEVICES AND CONNECTIONS
CONNECTING TO A COMPUTER
CONNECTING TO A COMPUTER
SETTING THE CONNECTION MODE
1
Start your computer, and use the supplied USB cable to connect the
camera to the computer.
h Connect the camera’s USB/AV terminal to the computer’s USB
terminal.
2
Turn on the camera (page 32).
h The screen to select the computer connection mode appears.
CARD READER:
Use the camera as an external drive of the computer (card reader mode).
WEB CAMERA:
Use your camera as a webcam (webcam mode).
USB CONNECTION
CARD READER
WEB CAMERA
CANCEL
SET
ENTER
Supplied USB cable
To USB/AV terminal
i Do not use any other USB cables except the supplied one.
To USB terminal
3
Select the desired connection mode, and press the SET button.
VQT3M88 123
HINT
About the USB cable
i Use only the supplied USB cable. Operation is not guaranteed if a different
USB cable is used.
i When using the SDXC Memory Card with a computer, please visit the
support web site shown below.
http://panasonic.net/avc/sdcard/information/SDXC.html
If the “Disconnect USB cable” message appears...
i Disconnect the USB cable once, then connect it again.
Insert and pull out the cable carefully
i When connecting the cables, make sure that the cable plugs are correctly
oriented and that they match the shapes of the terminal sockets on the
devices. Push the plugs in straight when connecting them. If undue force is
used to connect a cable, it may permanently damage the connector pins in
the terminal socket.
i Do not use excessive force when connecting and disconnecting cables.
i Please connect the USB cable to your computer’s USB terminal. Do not
connect it to the USB port on your monitor or keyboard, or to the USB hub.
In some instances, it may not be possible to correctly install the driver
software.
Do not exchange data bi-directionally
i While copying data from the camera to the computer in the card reader
mode, do not perform any operation that would copy the computer data to
the camera.
124 VQT3M88
USING AS A CARD READER
Mounting your camera
1
Set the camera to the card reader mode (page 123).
h The message [Found New Hardware] appears in the task tray,
showing that the camera is recognized as a drive.
h The card is recognized (mounted) as a disk, and the [CAM_SD (E:)]
icon appears in the [My Computer] window.
h The drive name (E:) may be different on your computer.
2
3
Select an action.
h If the [CAM_SD (E:)] window appears automatically, select the desired
procedure from the window.
Copy the files from your camera to the computer.
Dismounting the camera
HINT
i To disconnect your camera, be sure to follow the procedure below. Failure
to follow this procedure may cause faulty operation of your computer or
loss of card data.
1
Left-click on the icon for safely removing hardware in the task tray.
h A list appears showing the devices connected to the computer’s USB
terminal.
2
3
Left-click on the camera drive (E:).
Click on the [×] button.
h The camera can now be disconnected.
h The drive name (E:) may be different on your computer.
VQT3M88 125
ABOUT THE CONTENTS OF THE
CARD
Configuration of directories in the card
ROOT
DCIM
100CDPFP
IMGA0001.jpg
IMGA0002.jpg
IMGA0003.mp4
IMGA0004.m4a
IMGA0005.jpg
Image
Folder number
number
Image or
audio
recording
number
101CDPFP
IMGA0001.jpg
IMGA0002.jpg
IMGA0999.jpg
IMGA0001.jpg
IMGA0002.jpg
102CDPFP
h Up to 999 files can be stored in folder 100CDPFP. If more files are made, a
folder named 101CDPFP is created, and they will be stored in there. New
folders will then be named in sequence, i.e., 102CDPFP, 103CDPFP, etc.
File formats
The format of the files saved and the method in which the file names are
determined are explained below.
Type of file
File format
File name structure
File name begins with IMGA.
Extension is “.jpg”.
IMGA****.jpg
Photo
JPEG
File name begins with IMGA.
Extension is “.mp4”.
IMGA****.mp4
Video
MPEG-4
File name begins with IMGA.
Extension is “.m4a”.
IMGA****.m4a
Audio
recording
MPEG-4 Audio
(AAC compression)
Consecutive numbers assigned in the order the files were saved.
*
126 VQT3M88
When using as a card reader
i Do not alter files or folders in your camera in any way. Doing so may result
in your camera not recognizing that data.
If you want to edit files, first copy them to your computer’s hard drive.
i Cards formatted on your computer cannot be used by your camera. Format
all cards to be used by your camera with your camera.
HINT
About the volume name
i The volume name will be [CAM_SD] for a card that was formatted with the
camera and [Removable disc] for a card that was formatted with a
computer.
About videos recorded with this camera
i You can use Apple’s QuickTime to play back videos on a computer.
Playback may be possible using other software that supports the ISO
standard MPEG-4 AVC/H.264 (AAC audio).
<Video playback operating environment>
Windows
Mac OS
Windows XP
Windows Vista
Windows 7
OS*
Mac OS X 10.6.6 or later
Core 2 Duo E4400 2.0 GHz
or later
Core Duo T2600 2.16 GHz
or later
Athlon X2 4600+ 2.4 GHz or
later
CPU
Core 2 Duo or later
Memory
1 GB (Recommended 2 GB) or more
Video
128 MB or more
256 MB or more
USB terminal
memory
Other
* Limited to models with preinstalled OS.
VQT3M88 127
About audio files recorded with this camera
i Files can be played back using QuickTime.
We recommend using HD Writer VE 1.0 to copy or write back video data.
Using Windows Explorer or other programs on the PC to copy, move or
rename files and folders recorded with this unit will result in them being
unusable with HD Writer VE 1.0.
Selecting which medium to access
i The drive name for the built-in memory is “CAM_MEM(E:)”.
h The drive name (E:) may be different on your computer.
128 VQT3M88
k Copying files from the camera’s built-in memory and/or the SD card
to your PC
Card reader function (mass storage) (page 123)
Files from the camera’s built-in memory and/or the SD card can be copied to
the PC with Explorer or other programs.
1
2
Double click the folder that contains the still pictures. ([DCIM] _
[100CDPFP] etc.)
Drag and drop the files into the destination folder (on the PC’s HDD).
HINT
i Do not delete the SD card’s folders. Doing so may make the SD card
unusable in this unit.
i When data not supported by this unit has been recorded on a PC, it will not
be recognized by this unit.
i Always use this unit to format SD cards.
VQT3M88 129
USING AS A WEBCAM
This camera can be used as a webcam.
Operating environment
Windows
PC
IBM PC/AT compatible
OS
Microsoft Windows XP (32 bit) Home Edition
Service Pack 3
Microsoft Windows XP (32 bit) Professional
Service Pack 3
Microsoft Windows Vista (32 bit) Home Basic
Service Pack 1/Service Pack 2
Microsoft Windows Vista (32 bit) Home Premium
Service Pack 1/Service Pack 2
Microsoft Windows Vista (32 bit) Business
Service Pack 1/Service Pack 2
Microsoft Windows Vista (32 bit) Ultimate
Service Pack 1/Service Pack 2
Microsoft Windows Vista (32 bit) Enterprise
Service Pack 1/Service Pack 2
Microsoft Windows 7 (32 bit) Starter
Microsoft Windows 7 (32 bit/64 bit) Home Basic
Microsoft Windows 7 (32 bit/64 bit) Home Premium
Microsoft Windows 7 (32 bit/64 bit) Professional
Microsoft Windows 7 (32 bit/64 bit) Ultimate
®
®
CPU
RAM
Intel Pentium 4 1.7 GHz or more
Windows 7: 1 GB or more (32 bit), 2 GB or more (64
bit)
Windows Vista Home Basic: 512 MB or more
Windows Vista Ultimate/Business/Home Premium/
Enterprise: 1 GB or more
Windows XP: 512 MB or more
Required Software Windows Live Messenger
Interface
Other
USB port
High-speed broadband Internet connection
130 VQT3M88
* Operation is not guaranteed for all computers even if the recommended
system requirements are fulfilled.
* Operation is not guaranteed for NEC PC-98 series and their compatible
devices
* Windows 3.1, Windows 95, Windows 98/98SE, Windows Me,
Windows 2000 and Windows NT are not supported.
* Operation on an upgraded OS is not guaranteed.
Mac
Computer
Mac
OS
Mac OS X 10.6.6
®
™
CPU
Intel Core Duo or better
RAM
512 MB or more
Required software
Interface
Other
iChat
USB port
High-speed broadband Internet connection
* Operation is not guaranteed for all computers even if the recommended
system requirements are fulfilled.
HINT
i Although your camera can shoot at a maximum rate of 30 frames per
second, the rate at which you can broadcast in the webcam mode may be
less than this depending on the speed of your Internet connection.
Using as a webcam
1
Set the camera to the WEB CAMERA (webcam mode) (page 123).
VQT3M88 131
WHAT YOU CAN DO WITH A
COMPUTER
Contents of the supplied CD-ROM
HD Writer VE 1.0
You can copy the video/photo data to the HDD of a computer or write to
media like DVD discs or SD cards using HD Writer VE 1.0.
Refer to the owner’s manual of HD Writer VE 1.0 (PDF file) for details on how
to use it.
* Videos that were edited using HD Writer VE 1.0 can be played back on this
camera. However, they cannot be edited with this camera.
* Files that are larger than 4 GB are automatically divided into 4-GB files and
saved.
Smart wizard
The Smart wizard screen is automatically displayed when you connect this
unit to a computer with HD Writer VE 1.0 installed. (page 123)
Copy to PC:
You can copy video/photo data to the HDD of a computer.
Copy to disc:
You can copy to disc in conventional standard picture quality (MPEG2
format).
Online sharing:
Videos and photos can be shared on the Internet.
i Select the function you wish to use and follow the on-screen instructions
for easy copying.
132 VQT3M88
Software
required
Available function
Data type
Video and CD-ROM
Copying data to a computer
photo
HD Writer VE 1.0
Copying to DVD:
i Converted to conventional standard
quality (MPEG2 format).
Editing:
Video data copied to the HDD of a
computer can be edited.
i Add titles and transition effects,
trimming, splitting
Video
i Extract frames from the video
Online sharing:
You can upload videos on the Internet
and share them with your family and
friends.
Playing back on a computer:
Play back the video data in high definition
picture quality on a computer.
HD Writer VE 1.0
or Standard
Windows picture
viewer or a
commercially
available picture
viewer
Playing back on a computer
Photo
Copying videos to a computer (page 129)
Refer to page 147 if using a Mac.
Windows Explorer
Important Notice
i When using an SDXC Memory Card, check the following support
site. http://panasonic.net/avc/sdcard/information/SDXC.html
i When inserting a disc containing recorded videos into other
devices, a message prompting you to format the disc may be
displayed. Do not format the disc, since deleted data cannot be
restored later.
VQT3M88 133
HINT
i The software cannot process audio files.
i Videos that have been recorded on another device cannot be written
to the software supplied with this unit.
i We cannot guarantee operation if you use software other than that
supplied to read/write videos.
i Do not start the software supplied with this unit and other software at the
same time. Close any other software if you start the software supplied with
this unit and close the software supplied with this unit if you start any other
software.
End User License Agreement
Before opening the CD-ROM package, please read the following.
You (“Licensee”) are granted a license for the Software defined in this End
User License Agreement (“Agreement”) on condition that you agree to the
terms and conditions of this Agreement. If Licensee does not agree to the
terms and conditions of this Agreement, promptly return the Software to
Panasonic Corporation (“Panasonic”), its distributors or dealers from which
you made the purchase.
Article 1 License
Licensee is granted the right to use the software, including the information
recorded or described on the CD-ROM, instruction manuals, and any other
media provided to Licensee (collectively “Software”), but all applicable rights
to patents, copyrights, trademarks and trade secrets in the Software are not
transferred to Licensee.
134 VQT3M88
Article 2 Use by a Third Party
Licensee may not use, copy, modify, transfer or allow any third party, whether
free of charge or not, to use, copy or modify the Software, except as expressly
provided for in this Agreement.
Article 3 Restrictions on Copying the Software
Licensee may make a single copy of the Software in whole or a part solely for
backup purposes.
Article 4 Computer
Licensee may use the Software only on one computer, and may not use it on
more than one computer.
Article 5 Reverse Engineering, Decompiling or Disassembly
Licensee may not reverse engineer, decompile, or disassemble the Software,
except to the extent either of them is permitted under law or regulation of the
country where Licensee resides. Panasonic and its distributors will not be
responsible for any defects in the Software or damage to Licensee caused by
Licensee’s reverse engineering, decompiling, or disassembly of the Software.
Article 6 Indemnification
The Software is provided “AS-IS” without warranty of any kind, either
expressed or implied, including, but not limited to, warranties of non-
infringement, merchantability and/or fitness for a particular purpose. Further,
Panasonic does not warrant that the operation of the Software will be
uninterrupted or error free. Panasonic or any of its distributors will not be
liable for any damage suffered by Licensee arising from or in connection with
Licensee’s use of the Software.
Article 7 Export Control
Licensee agrees not to export or re-export to any country the Software in any
form without the appropriate export licenses under regulations of the country
where Licensee resides, if necessary.
Article 8 Termination of License
The right granted to Licensee hereunder will be automatically terminated if
Licensee contravenes any of the terms and conditions of this Agreement. In
this event, Licensee must destroy the Software and related documentation
together with all the copies thereof at Licensee’s own expense.
VQT3M88 135
OPERATING ENVIRONMENT
i Even if the system requirements mentioned in this owner’s manual are
fulfilled, some computers cannot be used.
i A CD-ROM drive is necessary to install the supplied software applications.
(A compatible DVD writer drive and media are necessary for writing to a
DVD.)
i Operation is not guaranteed in the following cases.
h When 2 or more USB devices are connected to a computer, or when
devices are connected through USB hubs or by using extension cables.
h Operation on an upgraded OS.
i This software is not compatible with Microsoft Windows 3.1, Windows 95,
Windows 98, Windows 98SE, Windows Me, Windows NT and Windows
2000.
Operating environment for HD Writer VE 1.0
Computer
IBM PC/AT compatible device equipped with Intel
Pentium 4 2.8 GHz or better CPU (including compatible
CPU)
h If using the playback function, Intel Core 2 Duo 2.16
GHz or higher, or AMD Athlon64 X2 Dual-Core
5200+ or higher is recommended
h If using the editing function, Intel Core 2 Quad 2.6
GHz or higher is recommended
OS
Microsoft Windows XP (32 bit) Home Edition
Service Pack 3
Microsoft Windows XP (32 bit) Professional
Service Pack 3
Microsoft Windows Vista (32 bit) Home Basic
Service Pack 1/Service Pack 2
Microsoft Windows Vista (32 bit) Home Premium
Service Pack 1/Service Pack 2
Microsoft Windows Vista (32 bit) Business
Service Pack 1/Service Pack 2
Microsoft Windows Vista (32 bit) Ultimate
Service Pack 1/Service Pack 2
Microsoft Windows 7 (32 bit) Starter
Microsoft Windows 7 (32 bit/64 bit) Home Basic
Microsoft Windows 7 (32 bit/64 bit) Home Premium
Microsoft Windows 7 (32 bit/64 bit) Professional
Microsoft Windows 7 (32 bit/64 bit) Ultimate
136 VQT3M88
RAM
Windows 7: 1 GB or more (32 bit)/2 GB or more (64 bit)
Windows Vista: 1 GB or more
Windows XP: 512 MB or more (1 GB or more
recommended)
Display
High Color (16 bit) or more (32 bit or more
recommended)
Desktop resolution of 1024×768 pixels or more
(1920×1080 pixels or more recommended)
Windows Vista/Windows 7: DirectX 9.0c compatible
video card (DirectX 10 recommended)
Windows XP: DirectX 9.0c compatible video card
Compatible with DirectDraw overlay support
PCI Express™×16 compatible recommended
Video memory 256 MB or more recommended
Direct3D Acceleration: Enabled*
* Checking the Direct3D Acceleration setting (when using
®
Windows XP)
[Start] → [Run] → The [Run] window appears. Enter
“dxdiag” in the text field and click the [OK] button. The
[DirectX Diagnostic Tool] window appears. Select the
[Display] tab and check [Direct3D Acceleration] under
[DirectX Features].
Free hard disk Ultra DMA – 100 or more
drive space
Available hard disk capacity of 450 MB or more for
installation
i When writing to disk (DVD) or card, at least twice the
amount of free disk space as the disk or card being
created is required. In addition, when exporting to
multiple disks while automatically partitioning, 17 GB
of free disk space is required.
i If the compression setting is enabled, errors will occur
during recording. In the [Properties] for the hard disk
drive, remove the check from the checkbox for
[Compress this drive to save disk space].
Sound
Drive
DirectSound Support
CD-ROM drive (for installation)
When writing to DVD, a compatible drive and media are
necessary.
Interface
USB port (high-speed USB [USB 2.0])
USB
connectable
model
A Panasonic video camera that this software is supplied
with
Applicable
content
Image data recorded on a Panasonic video camera that
this software is supplied with
VQT3M88 137
Other
Mouse or equivalent pointing device, SD card reader/
writer (required for reading and recording to SD cards;
performing these operations with SDHC memory cards
or SDXC memory cards requires an SDHC-compatible or
SDXC-compatible SD card reader/writer), an
environment with Internet access (required for online
functions “Online sharing”)
i Supplied CD-ROM is available for Windows only.
i Input is not supported in languages other than English, German, French
and Simplified Chinese.
i Operation cannot be guaranteed on all DVD drives.
i Operation is not guaranteed on Microsoft Windows Vista Enterprise,
Windows XP Media Center Edition, Tablet PC Edition and Windows 7
Enterprise.
i This software is not compatible with a multi-boot environment.
i This software is not compatible with a multi-monitor environment.
i Use the standard Windows fonts and display settings. Depending on the
settings, characters etc. may not display correctly in some cases.
i If using Windows XP, an administrative account user only can use this
software. If using Windows Vista/Windows 7, administrative account and
standard account users only can use this software. (An administrative
account user should install and uninstall this software.)
i Log on to the administrator account or a registered user account. A Guest
user account cannot be used.
i Operation on Windows 7 Ultimate or Windows Vista Ultimate when the
multilingual user interface (MUI) function is used to change the language is
not guaranteed.
i This software cannot be used simultaneously with other time-shifting
motion picture editing software or video capture products. Note that other
software running background processes, timer recording in particular, may
cause this software to malfunction.
i Unsupported files are not displayed.
i Some files that are unusually large or particular kinds of image formats
may not be displayed.
i When playing back MP4/iFrame videos, please check the following points
for your video card. In some cases images may not be correctly played
back or displayed. Dropped frames or uneven video playback may occur.
h Be sure to update your driver software to the latest version.
h Please update the standard graphics modules such as OS and DirectX
to the latest version for your video card.
138 VQT3M88
To use the HD Writer VE 1.0
You will need a high performance computer depending on the functions to be
used. It may not properly play back or properly operate depending on the
environment of the computer used. Refer to the operating environment and
notes.
HINT
i Operation during the playback may become slow if the CPU or memory is
not fulfilling the requirements of the operating environment.
i Always use the most current driver for the video card.
i Always make sure there is enough capacity on the HDD in the computer. It
may become inoperable or the operation may stop suddenly if the capacity
gets low.
VQT3M88 139
Operating environment for the card reader
function (mass storage)
Computer
OS
IBM PC/AT compatible PC
Microsoft Windows XP (32 bit) Home Edition
Service Pack 3
Microsoft Windows XP (32 bit) Professional
Service Pack 3
Microsoft Windows Vista (32 bit) Home Basic
Service Pack 1/Service Pack 2
Microsoft Windows Vista (32 bit) Home Premium
Service Pack 1/Service Pack 2
Microsoft Windows Vista (32 bit) Business
Service Pack 1/Service Pack 2
Microsoft Windows Vista (32 bit) Ultimate
Service Pack 1/Service Pack 2
Microsoft Windows Vista (32 bit) Enterprise
Service Pack 1/Service Pack 2
Microsoft Windows 7 (32 bit) Starter
Microsoft Windows 7 (32 bit/64 bit) Home Basic
Microsoft Windows 7 (32 bit/64 bit) Home Premium
Microsoft Windows 7 (32 bit/64 bit) Professional
Microsoft Windows 7 (32 bit/64 bit) Ultimate
CPU
RAM
Windows Vista/Windows 7: 1.0 GHz or higher
Windows XP: Intel Pentium III 450 MHz or higher or Intel
Celeron 400 MHz or higher
Windows 7: 1 GB or more (32 bit)/2 GB or more (64 bit)
Windows Vista Home Basic: 512 MB or more
Windows Vista Home Premium/Business/Ultimate/
Enterprise:
1 GB or more
Windows XP: 128 MB or more (256 MB or more
recommended)
Interface
USB port
Other
Mouse or equivalent pointing device
requirements
i Operates with the OS standard driver.
140 VQT3M88
INSTALLATION
When installing the software, log on to your computer as the Administrator or
with a user name with equivalent authorization. (If you do not have
authorization to do this, consult your manager.)
i Before starting the installation, close all applications that are running.
i Do not perform any other operations on your computer while the software
is being installed.
i Explanation of operations and screens is based on Windows Vista.
1
Insert the CD-ROM into the computer.
h The following screen is displayed automatically. Click [Run setup.exe]
→ [Continue].
h If Windows 7 is in use, or the following screen is not displayed
automatically, select [Start] → [Computer] (or double-click on
[Computer] on the desktop), and then double-click [Panasonic].
Click
Click
2
3
Click [Next].
Read the [End User License Agreement], then place a check beside
[I accept the terms of the license agreement] if you agree to them
and click [Next].
VQT3M88 141
4
5
6
Select the country or region
where you live, then click [Next].
h If the country or region cannot be
selected, select [NTSC Area].
h When the confirmation message
appears, click [Yes].
Click
Select where the application is to
be installed, then click [Next].
Click
Select [Yes] or [No] to create shortcut.
h A message regarding the playback in the environment used may be
displayed depending on the performance of the computer used. Click
[OK] after confirming.
7
8
Click [Next].
h When installation is complete, some notes will appear.
Check the contents, then close the window.
142 VQT3M88
9
Select [Yes, I want to restart my
computer now.], then click
[Finish].
The computer must be rebooted
for the application to work.
Click
VQT3M88 143
Uninstalling HD Writer VE 1.0
Follow the steps below to uninstall any software applications that you no
longer require.
1
Select [Start] →[Control Panel] →[Programs and Features].
Click
2
Select [HD Writer VE 1.0], then click [Uninstall].
h Proceed with the uninstallation by following the on-screen instructions.
h After uninstalling the software, be sure to reboot the computer.
Click
144 VQT3M88
STARTING HD WRITER VE 1.0
i When using HD Writer VE 1.0 on Windows XP, log on to your computer as
Administrator (or with a login name equally authorized). If you log on with a
login name other than Administrator, you cannot use the applications.
i When using HD Writer VE 1.0 on Windows Vista/Windows 7, log on to your
computer as Administrator (or with a login name equally authorized) or
with the user name for a standard user account. If you log on with a user
name for a guest user account, the software cannot be used.
(On the computer)
Select [Start] → [All Programs] → [Panasonic] → [HD Writer VE 1.0] →
[HD Writer VE].
Click
i For details on how to use the software applications, read the PDF owner’s
manual of the software.
VQT3M88 145
IF USING Mac
i HD Writer VE 1.0 is not available for Mac.
i iMovie ’11 is supported. For details about iMovie ’11, please contact Apple
Inc.
Operating environment
Computer
OS
CPU
RAM
Interface
Mac
Mac OS X 10.6.6
Intel Core Duo
1 GB or more
USB port
i Even if the system requirements mentioned in this owner’s manual are
fulfilled, some computers cannot be used.
i Operates with the OS standard driver.
i Supplied CD-ROM is available for Windows only.
Copying photos on a computer
1
Connect this unit to a computer via the supplied USB cable.
h The USB function selection screen will appear on the camera’s LCD
monitor.
h Do not use any other USB cables except the supplied one.
2
On the camera’s LCD monitor, select [CARD READER] and press the
SET button.
h This unit is automatically recognized as an external drive of Mac.
3
4
Double-click [CAM_SD] or [CAM_MEM] displayed on the desktop.
h Files are stored in the [100CDPFP] folder etc. in the [DCIM] folder.
Using a drag-and-drop operation, move the files you want to acquire
or the folder storing those files to any different folder on the
computer.
VQT3M88 147
To disconnect USB cable safely
Drag [CAM_SD] or [CAM_MEM] on the Desktop to the [Trash], and then
disconnect the USB cable.
HINT
About the USB cable
i Use only the supplied USB cable. Operation is not guaranteed if a different
USB cable is used.
i Do not remove the SD card from this unit when this unit is connected to the
computer using a USB cable.
148 VQT3M88
CONNECTING TO A TV
CONNECTING TO A TV
CONNECTING TO A TV
By connecting the camera to a TV, you can play back files from the installed
SD card or the built-in memory on the TV.
HINT
Insert and pull out the cable carefully
i When connecting the cables, make sure that the cable plugs are correctly
oriented and that they match the shapes of the terminal sockets on the
devices. Push the plugs in straight when connecting them. If undue force is
used to connect a cable, it may permanently damage the connector pins in
the terminal socket.
i Do not use excessive force when connecting and disconnecting cables.
About image output: The image output destination differs depending on the
camera status (page 110).
Recording mode
Standby Recording
Connection
cable
Image output
destination
Playback
mode
Camera LCD
monitor
n
NTSC:
PAL: m
n
m
n
m
m
n
m
n
AV cable
(supplied)
NTSC: m
TV
PAL: n
Camera LCD
monitor
n
NTSC:
PAL:
n
HDMI mini cable
(optional)
NTSC: m
TV
PAL: m
m: Images are output n: Images are not output
i HDMI, the HDMI logo and High-Definition Multimedia Interface are
trademarks or registered trademarks of HDMI Licensing, LLC.
VQT3M88 149
Connecting to a video input terminal
Use the supplied AV cable to connect to a TV.
Insert the plugs as far as they will go.
Set the input to
“VIDEO”.
AV cable (supplied)
To USB/AV terminal
White plug:To Audio Input (L) terminal
Red plug:To Audio Input (R) terminal
Yellow plug:To Video Input terminal
i Do not use any other AV cables except the supplied one.
Connecting to the HDMI terminal
Use a separately sold HDMI mini cable to connect to a TV.
Insert the plugs as far as they will go.
Set the input to
“HDMI”.
HDMI mini cable
(optional)
To HDMI terminal
To HDMI terminal on the TV
i Always use a genuine Panasonic HDMI mini cable (RP-CDHM15, RP-
CDHM30; optional).
150 VQT3M88
PLAYING BACK ON A TV
i After connecting the camera to the television, switch the TV input to the
terminal to which the camera is connected.
i The same playback procedure as when playing back with the camera is
used to play back audio recordings as well.
i The playback method is the same as when viewing images on the
camera’s LCD monitor. (Use the TV controls to adjust the volume.)
Playback using VIERA Link™ (HDAVI Control™)
What is the VIERA Link?
i This function allows you to use your remote control for the
Panasonic TV for easy operations when this unit is connected to
a VIERA Link compatible device using an HDMI mini cable for
automatic linked operations. (Not all operations are possible.)
i VIERA Link is a unique Panasonic function built on a HDMI
control function using the standard HDMI CEC (Consumer
Electronics Control) specification. Linked operations with HDMI
CEC compatible devices made by other companies are not
guaranteed. When using devices made by other companies that
are compatible with VIERA Link, refer to the owner’s manual for
the respective devices.
i This unit is compatible with VIERA Link Ver.5. VIERA Link Ver.5
is the newest Panasonic version and is also compatible with
existing Panasonic VIERA Link devices. (As of Dec 2010)
1
2
In the Option Setting Menu, for the TV OUTPUT setting, set “VIERA
Link” to “ON”.
: [Option tab “2”] → [TV OUTPUT] → [VIERA Link] → [ON]
i If you are not using VIERA Link, set to [OFF].
Use an HDMI mini cable to connect this unit to a Panasonic TV
compatible with VIERA Link with a HDMI mini cable.
i It is recommended to connect this unit to an HDMI terminal other
than HDMI1 if there are 2 or more HDMI input terminals on the TV.
i VIERA Link must be activated on the connected TV. (Read the
owner’s manual of the TV for how to set etc.)
i Always use a genuine Panasonic HDMI mini cable (RP-CDHM15,
RP-CDHM30; optional).
VQT3M88 151
3
Operate with the remote control for the TV.
1)
1)
DEC.20.2011
3.5MB
12:00 AM 101-0216
ENTER
SET
2)
3)
2)
1
1
2
DEC.20.2011
3)
3
DEC.20.2011
1) Press the button up, down, left or right to select a scene or photo to be
played back, and then press the button in the center to set it.
2) Navigate the operation icons that are displayed on the TV screen with the
remote control for the TV.
1 Operation icons
2 Cancel operation icons
3) To display the operation icons, press the submenu button.
3 Display operation icons
k Other linked operations
Turning the unit off:
If you use the remote control for the TV to turn off the power, this unit also
turns off.
Automatic input switching:
If you connect with a HDMI mini cable and then turn on this unit, the input
channel on the TV automatically switches to this unit’s screen. If the TV’s
power is in standby status, it will turn on automatically (if [Set] has been
selected for the TV’s [Power on link] setting).
i Depending on the HDMI terminal on the TV, the input channel may not
switch automatically. In this case, use the remote control for the TV to
switch the input channel.
152 VQT3M88
HINT
i If you are unsure whether or not the TV and AV amplifier you are using are
compatible with VIERA Link, read the owner’s manual for the devices.
i Operation is not possible with a cable that is not based on the HDMI
standard.
VQT3M88 153
COPYING/DUBBING
COPYING/DUBBING
COPYING/DUBBING
Dubbing in standard picture quality
Images played back on this unit can be dubbed onto a DVD recorder or video
device.
i Images can be played back even on devices other than high-
definition compatible devices, so this is recommended when dubbing
videos for distribution.
Change the video input on the video device and TV that this unit is
connected to.
i The channel set will differ depending on the terminal to which the unit is
connected.
i See the owner’s manual of the video device for details.
i Insert the plugs as far as they will go.
i Do not use any other AV cables except the supplied one.
Yellow
VIDEO IN
AUDIO IN
White (L)
Red (R)
AV cable (supplied)
To USB/AV terminal
1
Connect this unit to a video device and then change to the playback
mode.
2
3
Start playback on this unit.
Start recording on the connected device.
h To stop recording (dubbing), stop playback on this unit after stopping
recording on the recorder.
h It is not possible to directly insert in the card slot an SD card recorded
with this camera and play back or dub from it.
154 VQT3M88
h It is not possible to connect the camera to the USB connector and play
back or dub from it.
h It is not possible to record in HD with a Blu-ray disc recorder.
h It is not possible to directly insert an SD card recorded with this
camera in the card slot of a Panasonic TV and play back or dub from it
(as of December 2010).
h For information on how to display SD card images on your Panasonic
TV, please refer to the Users Manual for your TV.
HINT
i If the date and time display and function indication are not wanted, cancel
them before dubbing. (page 105)
i If the dubbed images are played back on a widescreen TV, the images may
be stretched vertically.
In this case, refer to the owner’s manual for the device you are connecting
to or read the owner’s manual of the wide-screen TV and set the aspect
ratio to 16:9.
VQT3M88 155
IMPORTANT MESSAGES AND ALERTS
IMPORTANT MESSAGES AND ALERTS
COMMONLY ASKED QUESTIONS
If you have a question about the camera operation, you might find the answer
in this compilation of commonly asked questions.
Question
Answer
Action
Why doesn’t the
power turn on?
Due to cold
temperatures, the your pocket to warm
battery pack
temporarily lost its
power.
Place the camera in
it up before using it.
Why is the battery The ambient
Keep the battery
pack in an
environment of 10 to
pack consumed
so quickly even
after it was fully
recharged?
temperature is
very low.
35 °C (50 to 95 °F).
The battery pack
life has expired.
If a battery becomes
depleted quickly even
after it was sufficiently
charged, it should be
assumed that the
Power
battery has reached
the end of its service
life. Please replace it
with a new battery.
Why doesn’t
recharging end?
The battery pack
life has expired.
Replace with a new
battery pack. If this
is not effective,
consult your dealer.
The remaining
battery pack
power is low.
Use the AC adaptor,
or replace the
battery pack with a
fully charged one.
Why does the
icon appear?
Why is the status
indicator lit red?
A recorded file is
being saved on
the card or built-in indicator turns off.
memory.
Not a malfunction.
Wait until the status
Why doesn’t the
flash operate?
The camera has
determined that
the image is bright the camera will
Not a malfunction.
Capture the image;
Shooting
enough and the
flash is not
determine when the
flash is necessary.
necessary.
156 VQT3M88
Question
Answer
Action
Are the settings
retained even
after the camera
is turned off?
—
Except for some
settings, such as the
exposure setting
and exposure
compensation, all
the settings are
retained even after
the camera is turned
off.
Which resolution
setting should I
use?
—
Select the resolution
setting according to
the intended use.
Picture quality E
or better:
Appropriate for
printing letter-size or
larger, and for
printing a close-up
of part of a photo
(trimming).
Shooting
, G, t:
For printing
standard photo
(photo service)
sizes.
, [:
For photos
displayed on a web
page, or sent as e-
mail attachments.
(Concerning the
image quality of
video recordings,
please see
page 181.)
VQT3M88 157
Question
What is the
difference
Answer
—
Action
Because shooting
with the optical
between the
digital zoom and
the optical zoom?
zoom uses the
optics of a physical
lens, you can shoot
without losing
minute details in the
image. The digital
zoom, on the other
hand, works by
magnifying a portion
of the image that
hits the image
sensor and may
produce a coarser
image.
How can I get the
distant view into
focus?
—
Set the scene mode
function to the
landscape
Shooting
mode when
photographing.
The video
appears to freeze RANGE button
for an instant.
(HX-DC1)
The ZOOM
Not a malfunction.
During the very brief
span that the zoom
lens is changing, the
recording appears
as a photo.
was pressed
during video
recording.
The zoom range
does not change
when the ZOOM
RANGE button is
pressed.
The ZOOM
RANGE button
was pressed while zoom. The zoom
the digital zoom
Not a malfunction.
Use the optical
range cannot be
changed while the
digital zoom is
engaged.
was engaged.
(HX-DC1)
158 VQT3M88
Question
Answer
Action
When used in
cold weather, why the LCD monitor
does the image
seem to leave
traces as it
Condition due to
Not a malfunction.
Spots that appear in
the LCD monitor
only appear in the
LCD monitor and
will not be recorded
with the images.
characteristics.
moves?
LCD
monitor
Why does the
displayed image
contain some red,
blue and green
dots, or why are
black spots
visible?
Why is the image The subject was
too bright? too bright.
When capturing an
image, devise a way
to compensate for a
bright subject, for
example, by
changing the
shooting angle.
Viewing
images
Why is the image The focus is not
out of focus? locked properly.
Hold the camera
correctly and slowly
press the [O]
button halfway to
lock the focus. Then
press the [O]
button all the way to
capture the image.
VQT3M88 159
Question
Why is there no
image?
Answer
This may happen Play back images
when trying to that were recorded
play back images on a card using this
Action
stored on a card
from a different
digital camera.
camera.
Viewing
images
Why is the
playback image
distorted?
If the subject
Not a malfunction.
This is a
characteristic of the
moves or the
camera is moved
during recording,
a distorted image
may sometimes
occur.
MOS sensor.
160 VQT3M88
Question
Answer
Due to the
characteristics of
Action
Why isn’t the
magnified image
clear?
Not a malfunction.
the camera,
magnified images
appear less clear.
Why isn’t the
captured image
clear?
The image was
captured using
the digital zoom.
Not a malfunction.
Can I play back
image and sound
files that I edited
using my
—
Please note
playback of files that
were processed
using software other
than HD Writer VE
1.0 cannot be
computer?
guaranteed.
Why is there a
motor-like sound
during video
playback?
The sound of the
camera’s
mechanical action
was recorded (the
sound of the
Not a malfunction.
Viewing
images
optical zoom
movement or the
autofocus sound).
Round white
When the flash is Not a malfunction. It
spots that look like used indoors or in is characteristic that
bubbles are
appear in photos. surroundings,
dark
the position and
number of round
dust in the air may spots changes with
reflect the light
from the flash and
appear as round
white dots.
each shot.
Why is there no
sound?
The volume on
the TV is set to
the minimum.
Adjust the volume
on the TV.
Connecting
to a TV
VQT3M88 161
Question
Answer
Action
The “Cannot edit, You have
Select videos that
were recorded in the
differing settings
exist.” message
appears.
attempted to
splice videos that same recording
were recorded in
different recording
modes.
mode.
Why is a noise
heard from a
nearby TV or
radio during
battery
Electromagnetic
waves are emitted adaptor further away
from the AC
adaptor.
Move the AC
from the TV or radio
when recharging the
battery pack.
recharging?
Why does the
“CARD FULL.” or
“Built-in Memory
full.” message
appear?
There is no more
available memory files, or use a card
on the card or in that has more
the camera’s built- memory available.
in memory.
Delete unnecessary
Misc.
Why does the
“Card is
protected”
The lock switch on Move the lock switch
the card is in the
to the unlocked
position.
locked (protect)
message appear? position.
Why can’t the
camera be
operated?
A temporary
Remove the AC
internal circuitry
problem may be
the cause.
adaptor and the
battery pack from
the camera, wait a
few minutes, then
reinstall the battery
pack and try again.
A problem such
as inability to
record or play
back occurs.
The card contains After saving your
files that were
saved using a
files to a different
medium, format the
device other than card.
this camera.
162 VQT3M88
Question
Answer
Action
Can I use my
camera abroad?
—
You can charge the
battery and connect
to a TV to view your
recordings when
abroad.
Why does the
“ERROR
OCCURRED.
PLEASE TURN
UNIT OFF, THEN
TURN ON
A problem has
occurred within
the camera or
card.
Check the following
items:
1 Remove the
card and then
install it again.
2 Remove the
battery pack and
then install it
AGAIN.” message
appear?
Misc.
again.
3 Install a different
card.
If “ERROR
OCCURRED.
PLEASE TURN
UNIT OFF, THEN
TURN ON AGAIN.”
still appears after
performing the
above steps, then
take the camera to
the dealer for
service.
VQT3M88 163
TROUBLESHOOTING
Before taking your camera to the repair shop, check the following table for a
possible solution to the problem.
Camera
Reference
page
Problem
Cause
Action
No power.
The battery
pack is dead.
Recharge the
battery pack, or
replace with a
fully charged
battery pack.
Or connect the
AC adaptor.
23
The battery
pack has not
been inserted
correctly.
Insert the
battery pack
correctly.
Power
A blinking
The battery
Wait for the
temperature
warning icon is
shown,
and the
camera does
not turn on.
pack is too hot. battery pack to
cool down.
29
33
The camera
turns off by
itself.
The camera
has switched
to the sleep
mode.
Turn on the
camera again.
164 VQT3M88
Reference
page
Problem
Cause
Action
An image is
not captured
when the [O]
button or [@]
button is
The power is
not turned on.
If the camera
has switched to
the sleep
mode, turn on
the camera
before
pressed.
32, 33
shooting.
If the camera
was turned off,
press the
power button to
turn it on.
The maximum Install a new
30
63
number of
images that
can be
captured or the
maximum
video
card.
Delete the
images that are
Shooting
not necessary.
recording time
has been
reached.
The flash does The flash
not operate.
Set the flash
mode is set to mode to k or
41
23
.
m.
The battery
pack is dead.
Recharge the
battery pack, or
replace with a
fully charged
battery pack.
Or connect the
AC adaptor.
VQT3M88 165
Reference
page
Problem
Cause
Action
The digital
The digital
Set the digital
zoom does not zoom setting is zoom setting to
work.
45, 57
43, 76
set to
.
.
There is noise The ISO
in the captured sensitivity
image.
Set the ISO
sensitivity to a
lower setting.
setting is too
high.
Shooting
The
appears, and
icon
The camera’s
internal
Discontinue
shooting, and
shooting is not temperature is wait for the
29
possible.
high.
camera to cool
down before
using it again.
166 VQT3M88
Reference
page
Problem
Cause
Action
No playback
image
appears.
The camera is Set the camera
LCD
monitor
not set to the
playback
mode.
to the playback
mode.
37
The image is
too dark.
The flash was
blocked by a
finger or other correctly, and
Hold the
camera
51
object.
make sure the
flash is not
obstructed.
The subject
was too far
away.
Capture the
image in the
range of
operation of the
flash.
188
The subject
was lit from
behind.
Set the flash
mode to m.
Viewing
images
41
85
Use the
exposure
compensation
function.
Use the spot
Y light-
measuring
mode.
43
There is not
enough light.
Adjust the ISO
sensitivity
setting.
43, 76
VQT3M88 167
Reference
page
Problem
Cause
The flash
Action
The image is
too bright.
Select a flash
mode other
mode is set to
41
85
m
.
than
Use the
was too bright. exposure
compensation
m.
The subject
function.
The ISO
sensitivity
setting is
incorrect.
Set the ISO
sensitivity to
43, 76
43, 75
=
.
The image is
not in focus.
The subject is
too close to the image with the
camera.
Capture the
subject within
the appropriate
distance/range.
Select the
correct focus
setting for your
needs.
The focus
setting is not
correct.
Viewing
images
The camera
moved when
Hold the
camera
correctly and
the [O
]
button was
pressed.
(camera
shake)
slowly press
the [O]
button halfway
to lock the
focus. Then
51, 54
The focus is
not locked
properly.
press the [
O]
button all the
way to capture
the image.
The lens is
dirty.
Clean the lens.
—
168 VQT3M88
Reference
page
Problem
Cause
Action
The colors of
the images
captured
This is due to
ambient
lighting.
Set the flash
mode to
.
41
indoors are not
correct.
The white
balancesetting balance setting
Set the white
43, 77
is incorrect. correctly.
A part of the
image is
missing.
The handstrap Hold the
or a finger was camera
blocking the
lens.
correctly, and
make sure the
51
—
Viewing
images
lens is not
obstructed.
“No image” is
shown.
There is no file Play back after
in the built-in
memory or in
the installed
card.
capturing
images or
making audio
recordings.
During audio
playback,there volume setting volume.
is no sound.
The play
Adjust the play
46, 60,
70, 151
on the camera
is too low.
There is no
color in the
image.
The TV output Select the
setting is not
correct.
correct TV
output setting.
Connecting
to a TV
107, 110
The image is
distorted.
VQT3M88 169
Reference
page
Problem
Cause
Action
No image or
sound.
The camera is Follow the
not correctly
connected to
the TV.
instructions to
make the
connection
correctly.
149, 151
Connecting
to a TV
The TV input
setting is not
correct.
Set the TV
input to the
correct setting.
The edge of
the image is
cut off.
This is a
characteristic
of the TV.
Not a
malfunction.
—
You cannot
edit or rotate
an image.
The protect
mode is set.
Cancel the
protect mode.
Image
editing
46, 87
The battery
pack is not
charging.
The AC
Connect the
AC adaptor
correctly.
adaptor is not
connected
properly.
Charging
27
The “This file is You have
Set the protect
setting for the
file to UNLOCK.
protected”
message
appears and
the file cannot
be deleted.
attempted to
delete a file
that is
46, 87
protected from
accidental
erasure.
The recording
capacity is less capacity is less the card, the
The recording
Depending on
Misc.
than that
shown in the
tables on
pages 181 to
184.
than the value
specified for
the card.
capacity may
be less than the
specified value.
Please refer to
the instructions
that
—
accompanied
the card.
170 VQT3M88
Restrictions concerning the Scene Mode and
Color Mode features
Scene Mode restrictions
Setting
Restrictions
Sports
Color mode: Fixed at
Focus: Fixed at *.
Exposure setting (HX-DC10): Fixed at @.
.
Portrait
Spot light
Snow
Color mode: Fixed at
Focus: Fixed at *.
.
Beach
Exposure setting (HX-DC10): Fixed at @.
White balance: Fixed at >.
Sunset
Color mode: Fixed at
.
Focus: Fixed at *.
Flash: Fixed at
ISO sensitivity: Fixed at =.
.
Fireworks
Subject tracking: Fixed at
.
Exposure compensation: Fixed at 0.0.
Exposure (HX-DC10): Fixed at @.
White balance: Fixed at >.
Color mode: Fixed at
Focus: Fixed at *.
Subject tracking: Fixed at
.
Landscape
.
Exposure (HX-DC10): Fixed at @.
VQT3M88 171
Setting
Restrictions
Color mode: Fixed at
Flash: Fixed at
.
.
Night scenery
Focus: Fixed at *.
Subject tracking: Fixed at
.
Exposure (HX-DC10): Fixed at @.
Color mode: Fixed at
Focus: Fixed at *.
Exposure (HX-DC10): Fixed at @.
.
Night portrait
Low light*
Color mode: fixed at
Focus: Fixed at *.
.
Flash: Fixed at
.
ISO sensitivity: Fixed at =.
Exposure (HX-DC10): Fixed at @.
* In some cases, the shutter speed may decrease to 1/15 sec.
HINT
When shooting hi-speed bursts...
i The shutter speed will be faster than 1/30 sec.
When recording a video...
i Even if the shutter speed is set to slower than 1/29 sec, the shutter speed
will be 1/30 sec.
Color Mode restrictions
Setting
Restrictions
Monochrome
Scene mode: Not available.
Color tracking: Not available.
Sepia
172 VQT3M88
About the scene mode function and focus setting
i The scene mode changes to
i Even if the focus is set to
when the focus is set to
or -, it changes to * when the scene
or -.
mode is set to any setting other than
.
About the status indicator when charging the
battery pack
When the status indicator is flashing fast or slow, it may indicate one of the
following conditions.
Flashing at about 4-second intervals (2 seconds on, 2 seconds off):
slower
i This may indicate that the battery has been fully discharged, or when the
battery temperature is high or low. The battery can be charged, but in
some cases it may take several hours to fully charge it.
i During normal charging, the status indicator flashes at about 2-second
intervals. However, even in this case, depending on the ambient
conditions, the status indicator may flash at 4-second intervals until the
battery is fully charged.
Flashing at about 0.5-second intervals (0.25 seconds on, 0.25 seconds
off): faster
i The battery pack cannot be charged. Remove the battery pack from the
camera once and reinsert it, then begin charging it again.
i Check to see that there is no dust, grime or foreign matter adhering to the
camera or battery, and make sure that the battery pack is correctly
inserted. Turn off the camera before cleaning it of dust, grime or other
foreign matter.
i The battery pack or the ambient temperature is very high or very low. Try
charging the battery pack again after it has returned to a suitable
temperature. If the battery pack still cannot be charged, it is possible that
the camera, the battery pack or the AC adaptor may be defective.
Off:
i Charging is complete.
i If the status indicator turns off even though charging is not completed, it is
possible that the camera, the battery pack or the AC adaptor may be
defective.
VQT3M88 173
ABOUT COPYRIGHT
k Carefully observe copyright laws
Whatever you have recorded and created can be used for your personal
entertainment only. Under copyright laws, other materials cannot be
used without obtaining permission from the holders of the copyrights.
It is forbidden to copy the software accompanying this unit, or to reproduce it
on a network, without permission.
k Licenses
i SDXC Logo is a trademark of SD-3C, LLC.
i HDMI, the HDMI Logo, and High-Definition Multimedia Interface are
trademarks or registered trademarks of HDMI Licensing LLC in the United
States and other countries.
™
i VIERA Link is a trademark of Panasonic Corporation.
®
®
®
i Microsoft , Windows and Windows Vista are either registered
trademarks or trademarks of Microsoft Corporation in the United States
and/or other countries.
i Microsoft product screen shot(s) reprinted with permission from Microsoft
Corporation.
i IBM and PC/AT are registered trademarks of International Business
Machines Corporation of the U.S.
®
™
®
®
i Intel , Core , Pentium and Celeron are the registered trademarks or
trademarks of Intel Corporation in the United States and other countries.
™
i AMD Athlon is a trademark of Advanced Micro Devices, Inc.
i iMovie and Mac are trademarks of Apple Inc., registered in the U.S. and
other countries.
i PowerPC is a trademark of International Business Machines Corporation.
i Other names of systems and products mentioned in these instructions are
usually the registered trademarks or trademarks of the manufacturers who
developed the system or product concerned.
This product is licensed under the AVC patent portfolio license for the
personal and non-commercial use of a consumer to (i) encode video in
compliance with the AVC Standard (“AVC Video”) and/or (ii) decode AVC
Video that was encoded by a consumer engaged in a personal and non-
commercial activity and/or was obtained from a video provider licensed to
provide AVC Video. No license is granted or shall be implied for any other
use. Additional information may be obtained from MPEG LA, LLC.
See http://www.mpegla.com.
174 VQT3M88
CAUTIONS FOR USE
Do not use this unit near radio
transmitters or high-voltage lines.
About the camera
i If you record near radio
transmitters or high-voltage lines,
the recorded pictures and/or
sound may be adversely affected.
The camera and the SD card
become warm during use.
This is normal and is not a
malfunction.
Make sure to use the supplied
cords and cables. If you use
optional accessories, use the
cords and the cables supplied
with them.
Do not extend the cords and the
cables.
Keep this unit as far away as
possible from electromagnetic
equipment (such as microwave
ovens, TVs, video games etc.).
i If you use this unit on top of or
near a TV, the pictures and/or
sound on this unit may be
disrupted by electromagnetic
wave radiation.
i Do not use this unit near cell
phones because doing so may
result in noise adversely affecting
the pictures and/or sound.
i Recorded data may be damaged,
or pictures may be distorted, by
strong magnetic fields created by
speakers or large motors.
i Electromagnetic wave radiation
generated by microprocessors
may adversely affect this unit,
disturbing the pictures and/or
sound.
i If this unit is adversely affected by
electromagnetic equipment and
stops functioning properly, turn
this unit off and remove the
battery or disconnect AC adaptor.
Then reinsert the battery or
reconnect AC adaptor and turn
this unit on.
Do not use insecticides or volatile
chemicals near or on the camera.
i If the camera is sprayed with
such chemicals, its body may be
marred and the surface finish
may peel off.
i Do not allow prolonged contact
with rubber or plastic products.
When you use the camera in a
sandy or dusty place such as a
beach, do not let sand or fine
dust get into the body and
terminals of the camera, and keep
the camera away from sea water.
i Sand or dust may damage the
camera. (Care should be taken
when inserting or removing the
SD card.)
i If sea water splashes on the
camera, wipe off the water with a
well-wrung cloth. Then wipe the
camera again with a dry cloth.
VQT3M88 175
When carrying the camera, do not
drop or bump it.
i A strong impact can break the
camera’s casing, causing it to
malfunction.
When disposing of or transferring
the camera
i Using this camera's [FORMAT] or
[DELETE] function only changes
the file management information
and does not completely delete
the built-in memory data. It may
be possible to recover (restore)
data using commercially available
software for that purpose.
i When disposing of the camera or
giving it to someone else, it is
recommended that you physically
format the built-in memory.
To physically format the built-in
memory, connect the AC adaptor
to the camera, eject the card from
the camera, select [FORMAT]
from Option Setting Menu 2, and
press the SET button.
Cleaning
Before cleaning the camera, remove
the battery and disconnect the
power cord from the power outlet,
and then wipe the camera with a
soft dry cloth.
i For stubborn dirt, soak a cloth in
water, wring it out well, and use it
to wipe the dirty surfaces. Then
dry the surfaces with a dry cloth.
i Use of benzine, paint thinner,
alcohol, or dishwashing liquid
may alter the camera body or
peel the surface finish. Do not
use these solvents.
When the display to delete the
built-in memory appears, select
[DELETE DATA], press the SET
button, and then follow the on-
screen instructions.
i When using a chemical dust
cloth, use in accordance with the
instructions that came with the
cloth.
i Managing the data in the built-in
memory is the responsibility of
the user. Panasonic does not
accept any responsibility in the
event that personal data is
Do not use the camera for
business purposes, such as for
surveillance.
i Continuous use could cause the
camera to overheat and break.
i This camera is not for
commercial use.
leaked.
When you are not going to use
the camera for an extended time
i When storing the camera in a
cupboard or cabinet, it is
recommended that you place a
desiccant (silica gel) in with it.
176 VQT3M88
About the battery
Prepare spare batteries when
going out.
i Prepare enough batteries to last
for 3 to 4 times the period you are
planning to record for. Cold
places such as a ski resort can
shorten recording time.
The battery used in this camera is a
rechargeable lithium-ion battery. It is
affected by humidity and
temperature, and the effect
increases the more the temperature
rises or falls.
In high temperatures, the protection
function may be triggered,
preventing use.
If you drop the battery
accidentally, check to see if the
terminals are damaged.
i Installing a battery with damaged
terminals can damage the
camera.
Be sure to remove and store the
battery after use.
i If left inside the camera, a minute
amount of current continues to
flow even if the camera is off.
Keeping the camera in this state
may cause the battery to over-
discharge, making it impossible
to use the battery even after it
has been charged.
Do not throw an old battery into
fire.
i Heating a battery or throwing it
into a fire may cause it to burst or
explode.
i The battery should be stored in a
vinyl bag to prevent metal from
contacting the terminals.
i The battery should be stored in a
cool place free from humidity,
with as constant a temperature
as possible. (Recommended
temperature: 0 °C to 30 °C (32 °F
to 86 °F); recommended
humidity: 40 %RH to 60 %RH)
i Extremely high or low
temperatures will shorten the life
of the battery.
i Environments that are hot, humid
or oily can rust the terminals and
damage the battery.
i If storing the battery for an
extended period of time, it is
recommended that you charge it
once a year, use it until it is
depleted, and store it again.
Remove any dust adhering to the
battery terminals.
If the battery does not last long
even after charging, it has
reached the end of its service life.
Please purchase a new battery.
About the AC adaptor
i If the temperature of the battery
is extremely high or extremely
low, charging may take time or
the battery may not be charged.
i If the AC adaptor is used near a
radio (especially during AM
reception), it may generate noise
in the radio. Keep the AC adaptor
at least 1 meter (3.3 feet) from
the radio.
i When using the AC adaptor, it
may generate an oscillating
sound. This is normal.
VQT3M88 177
i When not using the AC adaptor,
be sure to disconnect it from the
AC power outlet.
i Do not allow the terminal
contacts in the battery
Caution when disposing of or
transferring SD cards
i Using this camera or a computer
to format an SD card only
changes the file management
compartment or the battery
terminals to become dirty.
information and does not
completely delete the card data.
i It is recommended that the SD
card be physically destroyed, or
that this camera be used to
physically format the card if
giving it to someone else.
Connect the AC adaptor to a
nearby AC power outlet where the
power plug is easily accessible.
To physically format the SD card,
connect the AC adaptor to the
camera and proceed as follows.
Insert the SD card in the camera,
select [FORMAT] from Option
Setting Menu 2, and press the
SET button. Next select [DELETE
DATA], and press the SET button.
When the display to delete data
from the SD card appears, select
[YES], and then follow the on-
screen instructions.
About the SD card
i The memory capacity indicated
on the SD card label is the total of
the capacity for copyright
protection and management, and
that ordinarily used by the
camera, computers, etc.
i Do not subject the SD card to a
strong impact. Do not bend or
drop it.
i SD card data may be corrupted
or lost due to electrical noise or
static electricity, or damage to the
camera or the card.
i Managing the data in the SD card
is the responsibility of the user.
Caution when handling SD cards
i Do not allow grime, water or
foreign matter to adhere to the
terminals on the back of the SD
card.
i When used for an extended
period of time, the camera
surface and the SD card may
become rather warm, but this is
not a malfunction.
i Do not leave cards in the
following places:
Do not perform any of the
following operations while the SD
card is being accessed (the
status indicator is lit red).
h Remove the SD card
h Turn the camera off
h Insert or remove the USB
cable
h Where exposed to high
temperatures, such as under
direct sunlight or near a heater
h Humid or dusty places
h Where exposed to extreme
temperature changes
(condensation may occur)
h Where exposed to static
electricity or electromagnetic
waves
h Expose the camera to
vibrations or shock.
i When not using, store the SD
card in its case.
178 VQT3M88
About the LCD monitor
About condensation
i If the LCD monitor is dirty, wipe it
clean with a soft cloth such as an
eyeglass cleaning cloth.
i Do not scratch or press the LCD
monitor with strong force.
i If you affix a screen protector
sheet to the LCD monitor, it may
become difficult to see.
i In an environment with extreme
temperature changes,
If you take a cold drink bottle from
the refrigerator on a hot summer
day and leave it for a while, you will
find that water droplets have formed
on the surface of the bottle. This is
called “condensation”.
If condensation forms on the
camera, the lens will fog up and the
camera may not work properly.
Make every effort to ensure that
condensation does not form, or if it
does form, take appropriate action.
condensation may form on the
LCD monitor. Wipe it with a soft
cloth such as an eyeglass
cleaning cloth.
Causes of condensation
i Condensation occurs when the
ambient temperature or
humidity has changed, as in
the following:
h When the camera is brought
inside from the cold (for
example, a ski slope) to a
warm room
i When the camera has become
very cold, for example in cold
surroundings, the LCD monitor
will be slightly darker than usual
immediately after the camera is
turned on. Normal brightness will
be restored when the camera's
internal temperature rises.
h When the camera is moved
from an air-conditioned car to
outside
h When a cold room has been
warmed up quickly
h When cool wind from an air
conditioner blows directly on
the camera
h After summer rain showers
h When the camera is in a very
humid place where the air is
thick with steam (for example,
a heated swimming pool)
The LCD monitor is
manufactured using high-
precision technology;
however, black spots may
appear on the screen or some
pixels (red, blue or green) may
stay lit. This is normal and is
not a malfunction.
The effective pixel rate of the
LCD monitor is maintained at a
very accurate 99.99%, and dead
or stuck pixels may occur in at
most 0.01% of the pixels. Note
that these pixel defects are not
recorded with the captured
images and are not a cause for
concern.
VQT3M88 179
Hint for using in extreme
temperature changes
For example, if you bring the
camera into a heated room after
using it on a ski slope, place the
camera in a plastic bag, remove as
much air as possible from the bag,
then seal the bag. Leave the camera
for about an hour to allow the
temperature of camera to adjust to
the ambient temperature of the
room before using it.
Treating a foggy lens
Remove the battery and AC
adaptor, and leave the camera for
about 1 hour. The cloudiness will
dissipate naturally when the camera
adjusts to the ambient temperature.
180 VQT3M88
RECORDING MODES/APPROXIMATE
RECORDABLE TIME
For SD cards, only the principal memory capacities are listed. The times
indicated are rough approximations of possible continuous recording times.
When
using a
Mac for
playback/
editing
1
2
*1
*1
*1
*1
*2
Recording mode
Picture size
1920× 1920× 1280× 1280× 640×
1080
960×
540
Voice
memo
1080
720
720
480
2 h
20 min
9 h
4 GB 20 min 30 min 30 min 50 min
20 min
32 h
131 h
532 h
1 h
2 h
2 h
3 h
1 h
SD card 16 GB
50 min 10 min 10 min 30 min 50 min 20 min
7 h
8 h
8 h
13 h
5 h
20 min
64 GB
32 h
30 min 30 min 30 min 30 min
Approx.
80 MB 25 sec 30 sec 30 sec 50 sec 2 min 15 sec 30 min
(HX-DC10)
Built-in
memory
Approx.
80 MB 25 sec 30 sec 30 sec 50 sec 2 min 15 sec 30 min
(HX-DC1)
1 Favors image quality
2 Favors recording time
* 1: HD image quality
* 2: Conventional standard image quality
i If recording for long periods, prepare batteries for 3 or 4 times the period
you wish to record for. (page 23)
i The default recording mode is
.
i If a recording with a lot of action is recorded, the recordable time is less.
i The recordable time may be less if recording mostly short videos.
VQT3M88 181
i When the recording mode setting is set to audio recording <, and the
recording exceeds about 5 hours, the recorded file is saved and the audio
recording ends. For other recording mode settings, when the file size
exceeds 4 GB, the recorded file is saved once, and the recording continues
in a new file. (These 4 GB segments are automatically created. The
recording session continues until you stop recording.)
i For model HX-DC1, about 30 seconds before the 4 GB capacity is
reached, the countdown indication appears. When the countdown
indication reaches “0”, the “SAVING” message appears and the file is
saved, and then video recording continues in a new file.
i Even with cards of the same capacity, the amount of data that can actually
be stored may differ depending on the card brand or type, recording
conditions, etc.
i The continuous recording time may differ depending, for example, on the
card type, capacity, efficiency, etc.
182 VQT3M88
APPROXIMATE NUMBER OF
RECORDABLE PICTURES
For SD cards, only the principal memory capacities are listed.
The times indicated are rough approximations of possible continuous
recording times.
k Photo recording (single-shot)
HX-DC10
A
B
Recording pixels
4608×3456 4608×3456 4608×2592
4 GB
16 GB
64 GB
400
1900
7900
700
2900
12000
900
3900
15900
SD card
Built-in Approx.
memory 80 MB
10
15
20
HX-DC1
6
7
Recording pixels
4352×3264 4352×3264 4352×2448
4 GB
16 GB
64 GB
500
2200
8900
800
3300
13300
1000
4300
17600
SD card
Built-in Approx.
memory 80 MB
10
15
20
VQT3M88 183
HX-DC10/HX-DC1
[
640×480
23900
97600
247100
G
Recording pixels
1920×1080 1600×1200 1280×720
4 GB
5200
21200
82300
5400
22100
82300
9900
40600
164700
SD card
16 GB
64 GB
Approx.
80 MB
(HX-DC10)
Approx.
80 MB
110
110
110
110
200
200
500
500
Built-in
memory
(HX-DC1)
k Hi-Speed Burst
HX-DC10/
HX-DC1
HX-DC10
HX-DC1
Recording pixels
C
4608×3456
700
2900
12000
:
t
4352×3264 1600×1200
4 GB
16 GB
64 GB
800
3300
13300
5400
22100
82300
SD card
Approx.
80 MB
(HX-DC10)
Approx.
80 MB
15
–
–
110
110
Built-in
memory
15
(HX-DC1)
184 VQT3M88
SPECIFICATIONS
Specifications may change without prior notice.
Digital Movie Camera
Power source:
DC 5.0 V (when using AC adaptor)
3.7 V (when using battery)
Power consumption: (When recording)
HX-DC10: 2.3 W; HX-DC1: 2.9 W
Signal system:
1080/60i, 1080/30p, 720/60p, 720/30p, 480/30p, 540/30p
Recording format:
Video:
MPEG-4 AVC/H.264 file format compliant, iFrame
Voice memo: MPEG-4 AAC audio
Image sensor:
<HX-DC10>
1/2.3” MOS image sensor
Total:
Approx. 16,790,000 pixels (16.79 megapixels)
Effective pixels
Video:
Photo:
Approx. 16 Mpx (4:3), Approx. 11.9 Mpx (16:9)
Approx. 16 Mpx (4:3), Approx. 11.9 Mpx (16:9)
<HX-DC1>
1/2.33” MOS image sensor
Total:
Approx. 14,400,000 pixels (14.4 megapixels)
Effective pixels
Video:
Photo:
Approx. 14.3 Mpx (4:3), Approx. 11.9 Mpx (16:9)
Approx. 14.3 Mpx (4:3), Approx. 11.9 Mpx (16:9)
VQT3M88 185
Lens:
<HX-DC10>
Auto iris, 5× power zoom
Macro
F3.5 to F3.7 (f=6.8 mm to 34.0 mm)
35mm equivalent:
Video:
38.1 mm to 457.2 mm (4:3)
41.5 mm to 249.0 mm (60i/60p, 16:9)
41.5 mm to 498.0 mm (30p, 16:9)
38.1 mm to 190.5 mm (4:3)
Photo:
41.5 mm to 207.5 mm (16:9)
Minimum focus distance:
Normal:
Approx. 10 cm (3.9”) (Wide)/Approx. 80 cm (31”)
(Tele)
Intelligent Auto macro: Approx. 1 cm (0.4”) (Wide)/Approx. 80 cm (31”)
(Tele)
<HX-DC1>
Auto iris, 5× power zoom
Macro
F3.5 to F3.7 (f=6.8 mm to 34.0 mm)
35 mm equivalent
Video (Wide): 39.2 mm to 235.2 mm (4:3)
40.1 mm to 240.6 mm (16:9)
(Tele): 80.9 mm to 485.4 mm (4:3)
82.4 mm to 494.4 mm (16:9)
Photo:
38.6 mm to 193.0 mm (4:3)
39.9 mm to 199.5 mm (16:9)
Minimum focus distance:
Normal:
Approx. 10 cm (3.9”) (Wide)/Approx. 80 cm (31”)
(Tele)
Macro:
Approx. 1 cm (0.4”) (Wide)/Approx. 80 cm (31”)
(Tele)
Zoom:
<HX-DC10>
(Photo) 5× optical zoom; (Video) 12× (30p)/6× (60i/60p) advanced zoom
Digital zoom; 120× (video mode, 30p mode), 60× (video mode, 60i/60p
mode), 50× (photo mode)
<HX-DC1>
(Photo) 5× optical zoom; (Video)12× double-range zoom
Digital zoom; 60× (video mode), 50× (photo mode)
186 VQT3M88
Image stabilizer:
Electronic
Monitor:
3.0” wide LCD monitor (Approx. 230K dots)
Microphone:
Internal stereo microphone
Speaker:
1 round speaker, dynamic type
White balance adjustment:
Auto tracking white balance system
Standard illumination:
1,400 lx
Minimum required subject illumination:
<HX-DC10>
Approx. 3 lx (1/15 sec in the scene mode low light setting),
Approx. 9 lx (1/30 sec in the scene mode OFF setting)
<HX-DC1>
Approx. 5 lx (1/15 sec in the scene mode low light setting),
Approx. 17 lx (1/30 sec in the scene mode OFF setting)
AV multi connector video output:
1.0 Vp-p, 75Ω
HDMI mini connector video output:
™
HDMI 1080i/720p/480p
AV multi connector audio output:
155 mV, output impedance 220Ω, 2 ch
VQT3M88 187
HDMI mini connector audio output:
Linear PCM
USB:
Reader/writer function
SD card:
Read/Write (No copyright protection support)
Built-in memory: Read/Write
Hi-Speed USB (USB 2.0), micro USB terminal
Webcam
Compression:
Image size:
Motion JPEG
640×480 pixels
Flash:
Effective range: Approx. 80 cm to 2.1 m (2.6 feet to 6.9 feet)
Dimensions (excluding projecting parts):
86.2 mm (W)×120.8 mm (H)×38.1 mm (D)
[3.40” (W)×4.76” (H)×1.50” (D)]
Mass (weight):
<HX-DC10>
Approx. 161 g (Approx. 0.355 lbs.) (without battery and SD card)
<HX-DC1>
Approx. 163 g (Approx. 0.360 lbs.) (without battery and SD card)
Mass (weight) in operation:
<HX-DC10>
Approx. 179 g (Approx. 0.395 lbs.) (with battery and SD card)
<HX-DC1>
Approx. 181 g (Approx. 0.399 lbs.) (with battery and SD card)
Operating temperature:
0 °C to 35 °C (32 °F to 95 °F)
Operating humidity:
10 %RH to 80 %RH
188 VQT3M88
Battery operation time:
See page 23
k Video
Recording media:
SD Memory Card (FAT12 and FAT16 system compliant)
SDHC Memory Card (FAT32 system compliant)
SDXC Memory Card (exFAT system compliant)
Refer to page 18 for details concerning SD cards that can be used in this unit.
Built-in memory: Approx. 80 MB (HX-DC10)
Approx. 80 MB (HX-DC1)
Compression:
MPEG-4 AVC/H.264, iFrame
Recording modes:
: Approx. 17 Mbps (VBR)
: Approx. 15 Mbps (VBR)
: Approx. 15 Mbps (VBR)
: Approx. 9 Mbps (VBR)
: Approx. 3 Mbps (VBR)
: Approx. 24 Mbps (VBR)
Refer to page 181 for recordable times.
Picture size:
: 1920×1080/60i
: 1920×1080/30p
: 1280×720/60p
: 1280×720/30p
: 640×480/30p
: 960×540/30p
Audio compression:
AAC (2 ch)
VQT3M88 189
k Photo
Recording media:
SD Memory Card (FAT12 and FAT16 system compliant)
SDHC Memory Card (FAT32 system compliant)
SDXC Memory Card (exFAT system compliant)
Refer to page 18 for details concerning SD cards that can be used in this unit.
Built-in memory: Approx. 80 MB (HX-DC10)
Approx. 80 MB (HX-DC1)
Compression:
JPEG (DCF/Exif2.2 standard)
Picture size:
Photo recording (single-shot)
<HX-DC10>
A
: 4608×3456 pixels
B: 4608×3456 pixels
: 4608×2592 pixels
<HX-DC1>
6
7
: 4352×3264 pixels
: 4352×3264 pixels
: 4352×2448 pixels
<HX-DC10/HX-DC1>
: 1920×1080 pixels
: 1600×1200 pixels
G
: 1280×720 pixels
[: 640×480 pixels
Hi-Speed Burst
<HX-DC10>
C: 4608×3456 pixels
<HX-DC1>
:: 4352×3264 pixels
<HX-DC10/HX-DC1>
t: 1600×1200 pixels
Refer to page 183 for the number of recordable images.
AC adaptor
Power source:
AC input:
DC output:
AC 100 V to 240 V, 50/60 Hz
130 mA
5.0 V, 1.0 A
190 VQT3M88
OPTIONAL ACCESSORIES
Accessory No.
Figure
Description
VW-VBX070
Battery pack
RP-CDHM15
RP-CDHM30
HDMI mini cable
RP-SDN16GU1A
RP-SDN08GU1A
RP-SDN04GU1A
RP-SDN02GU1A
Class 4 16 GB SDHC Memory Card
Class 4 8 GB SDHC Memory Card
Class 4 4 GB SDHC Memory Card
Class 4 2 GB SD Memory Card
RP-SDW64GU1K
RP-SDW48GU1K
RP-SDW32GU1K
RP-SDW16GU1K
RP-SDW08GU1K
RP-SDW04GU1K
Class 10 64 GB SDXC Memory Card
Class 10 48 GB SDXC Memory Card
Class 10 32 GB SDHC Memory Card
Class 10 16 GB SDHC Memory Card
Class 10 8 GB SDHC Memory Card
Class 10 4 GB SDHC Memory Card
NOTE:
Accessories and/or model numbers may vary by country. Please
consult your local dealer.
Product numbers correct as of Feb. 2011. These may be subject to
change.
VQT3M88 191
Accessory Order Form (For USA and Puerto
Rico Customers)
Please photocopy this form when placing an order.
1. Model #
2. Items Ordered
Accessory #
Description
Price Each
Quantity
Total Price
Subtotal
Your State & Local Sales Tax
Shipping & Handling
Total Enclosed
6.95
3. Method of payment (check one)
Check of Money Order enclosed (NO C.O.D.SHIPMENTS)
VISA
Credit Card #
MasterCard
Discover
Expiration Date
Customer Signature
Make Check or Money Order Payable to: PANASONIC ACCESSORIES
(Please do not send cash)
4. Shipping information (UPS delivery requires complete street address)
Ship To:
Mr.
Mrs.
Ms.
Phone#:
First
Last
(
)
Day
Street Address
City
(
)
Night
State
Zip
TO OBTAIN ANY OF OUR ACCESSORIES YOU CAN DO ANY OF
THE FOLLOWING:
VISIT YOUR LOCAL PANASONIC DEALER
OR
CALL PANASONIC’S ACCESSORY ORDER LINE AT 1-800-332-5368
[6 AM-6 PM M-F, PACIFIC TIME]
OR
MAIL THIS ORDER TO: PANASONIC SERVICE AND TECHNOLOGY COMPANY
ACCESSORY ORDER OFFICE
20421 84th Avenue South Kent, WA. 98032
192 VQT3M88
Limited Warranty
(ONLY FOR U.S.A. AND PUERTO RICO)
Panasonic Consumer Electronics Company,
Division of Panasonic Corporation of North America
One Panasonic Way, Secaucus, New Jersey 07094
Panasonic Camcorder Products
Limited Warranty
Limited Warranty Coverage (For USA and Puerto Rico Only)
If your product does not work properly because of a defect in materials or
workmanship, Panasonic Consumer Electronics Company (referred to as “the
warrantor”) will, for the length of the period indicated on the chart below,
which starts with the date of original purchase (“warranty period”), at its
option either (a) repair your product with new or refurbished parts, (b) replace
it with a new or a refurbished equivalent value product, or (c) refund your
purchase price. The decision to repair, replace or refund will be made by the
warrantor.
Product or Part Name
Camcorder
Parts
Labor
1 year
90 days
Rechargeable Batteries
(defective exchange)
10 days
90 days
Not Applicable
Not Applicable
SD Memory Cards
(defective exchange)
During the “Labor” warranty period there will be no charge for labor. During
the “Parts” warranty period, there will be no charge for parts. This Limited
Warranty excludes both parts and labor for non-rechargeable batteries,
antennas, and cosmetic parts (cabinet). This warranty only applies to
products purchased and serviced in the United States or Puerto Rico. This
warranty is extended only to the original purchaser of a new product which
was not sold “as is”.
Carry-In or Mail-In Service
To find a service center please visit http://www.panasonic.com/help or call
1-800-211-PANA (7262).
When shipping the unit, carefully pack, include all supplied accessories listed
in the Owners Manual, and send it prepaid, adequately insured and packed
well in a carton box. When shipping Lithium Ion batteries please visit our
Web Site at www.panasonic.com/BatteryHandling as Panasonic is committed
to providing the most up to date information. Include a letter detailing the
complaint, a return address and provide a daytime phone number where you
can be reached. A valid registered receipt is required under the Limited
Warranty.
VQT3M88 193
IF REPAIR IS NEEDED DURING THE WARRANTY PERIOD, THE
PURCHASER WILL BE REQUIRED TO FURNISH A SALES RECEIPT/
PROOF OF PURCHASE INDICATING DATE OF PURCHASE, AMOUNT
PAID AND PLACE OF PURCHASE. CUSTOMER WILL BE CHARGED FOR
THE REPAIR OF ANY UNIT RECEIVED WITHOUT SUCH PROOF OF
PURCHASE.
Limited Warranty Limits And Exclusions
This warranty ONLY COVERS failures due to defects in materials or
workmanship, and DOES NOT COVER normal wear and tear or cosmetic
damage. The warranty ALSO DOES NOT COVER damages which occurred
in shipment, or failures which are caused by products not supplied by the
warrantor, or failures which result from accidents, misuse, abuse, neglect,
mishandling, misapplication, alteration, faulty installation, set-up adjustments,
misadjustment of consumer controls, improper maintenance, power line
surge, lightning damage, modification, introduction of sand, humidity or
liquids, commercial use such as hotel, office, restaurant, or other business or
rental use of the product, or service by anyone other than a Factory Service
Center or other Authorized Servicer, or damage that is attributable to acts of
God.
THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED UNDER
“LIMITED WARRANTY COVERAGE”.
THE WARRANTOR IS NOT LIABLE FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS
PRODUCT, OR ARISING OUT OF ANY BREACH OF THIS WARRANTY.
(As examples, this excludes damages for lost time, travel to and from the
servicer, loss of or damage to media or images, data or other memory or
recorded content. The items listed are not exclusive, but for illustration only.)
ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE
WARRANTY OF MERCHANTABILITY, ARE LIMITED TO THE PERIOD OF
THE LIMITED WARRANTY.
Some states do not allow the exclusion or limitation of incidental or
consequential damages, or limitations on how long an implied warranty lasts,
so the exclusions may not apply to you.
This warranty gives you specific legal rights and you may also have other
rights which vary from state to state. If a problem with this product develops
during or after the warranty period, you may contact your dealer or Service
Center. If the problem is not handled to your satisfaction, then write to the
warrantor’s Consumer Affairs Department at the addresses listed for the
warrantor.
PARTS AND SERIVCE, WHICH ARE NOT COVERED BY THIS LIMITED
WARRANTY, ARE YOUR RESPONSIBILITY.
194 VQT3M88
Customer Services Directory (United States and Puerto Rico)
Obtain Product Information and Operating Assistance; locate your
nearest Dealer or Service Center; purchase Parts and Accessories;
or make Customer Service and Literature requests by visiting our
Web Site at:
http://www.panasonic.com/help
or, contact us via the web at:
http://www.panasonic.com/contactinfo
You may also contact us directly at:
1-800-211-PANA (7262)
Monday-Friday 9am-9pm, Saturday-Sunday 10am-7pm EST
For hearing or speech impaired TTY users, TTY: 1-877-833-8855
Accessory Purchases (United States and Puerto Rico)
Purchase Parts, Accessories and Instruction Books online for all
Panasonic Products by visiting our Web Site at:
http://www.pstc.panasonic.com
Or, send your request by E-mail to:
You may also contact us directly at:
1-800-332-5368 (Phone) 1-800-237-9080 (Fax Only)
(Monday-Friday 9am-9pm EST)
Panasonic Service and Technology Company
20421 84th Avenue South, Kent, WA 98032
(We accept Visa, MasterCard, Discover Card, American Express, and
Personal Checks)
For hearing or speech impaired TTY users, TTY: 1-866-605-1277
As of (March 2011)
VQT3M88 195
Spanish Quick Use Guide/Guía
española para el uso rápido
Instalación de la batería y de la tarjeta SD
1
Inserte la batería.
h Es posible insertar la batería incorrectamente, de manera que ponga
especial atención para insertarla en su orientación correcta.
Tapa del
compartimiento
de la batería
Tire hacia
afuera
Marcas del
conector
1
3 Abra
Batería
2
4
Inserte haciendo coincidir las marcas de conexión
2
Inserte la tarjeta SD.
1 Abra
2
h
Inserte la tarjeta
Empuje recto hasta
que escuche un
sonido de clic.
3 Cierre
Lado etiquetado de
la tarjeta
4
Cierre firmemente
hasta que escuche
un sonido de clic.
196 VQT3M88
3
Carga de la batería.
h Utilice el cable USB (suministrado) para conectar la cámara y el
adaptador de C.A. y, a continuación, conecte el adaptador de C.A. a
una toma de corriente.
h Use sólo el cable USB suministrado. La operación no está
garantizada si se usa un cable USB diferente.
h El adaptador de C.A. es adecuado solamente para esta cámara.
No lo use con otros dispositivos.
h La recarga sólo se efectúa cuando la cámara está apagada o en el
modo de reposo. La recarga no se produce cuando la cámara está en
el modo de grabación o de reproducción.
3 A la toma de
corriente
1 Abra
2
Adaptador de CA
Al adaptador de C.A.
<Durante la carga ...>
i Si la batería está defectuosa o no está instalada correctamente, la luz roja
del indicador de estado parpadea a intervalos de 0.5 segundos.
Asegúrese que la batería está instalada correctamente.
i Si la batería aún no se puede
recargar, es posible que haya un fallo
de funcionamiento en la cámara, la
batería o el adaptador de C.A.
i Cuando se completa la carga se
apaga el indicador de estado.
i El tiempo de carga es de
Indicador de
estado
aproximadamente 120 minutos.
VQT3M88 197
ENCENDIDO Y APAGADO DE LA CÁMARA
Encendido de la cámara
1
Abra la unidad de pantalla y
presione el interruptor.
h El monitor LCD se enciende.
Unidad de pantalla
Interruptor
Pantalla LCD
<Apertura de la unidad de pantalla>
90°
180°
105°
198 VQT3M88
Apagado de la cámara
2
Presione el interruptor durante al menos 1 segundo.
h La cámara se apaga.
h Si pulsa ligeramente el interruptor una vez, la cámara pasará al modo
de reposo.
CAMBIO ENTRE EL MODO DE GRABACIÓN Y
EL DE REPRODUCCIÓN
1
Presione el botón REC/
h Cambia el modo.
.
h El modo cambia cada vez que se
presiona el botón REC/
.
Botón REC/
VQT3M88 199
Selección del idioma de la pantalla
1
Presione el botón MENU.
RECORDING MENU 1
1
2
3
1080-30p
REC MODE
PICTURE SIZE
SCENE MODE
COLOR MODE
FLASH
-
16M
S
1
2
3
SELF TIMER
SET
ENTER
Pestaña de opciones
2
Seleccione la pestaña de
opciones “2”, y presione el botón
SET.
h Aparece el menú de ajuste de
opciones.
h Si mueve el botón SET hacia la
derecha, aparecerá la pantalla
para seleccionar un ajuste para
modificar.
OPTION MENU 2
LANGUAGE
TV OUTPUT
INITIAL SET
FORMAT
1
2
3
1
2
3
ENTER
3
4
Seleccione [LANGUAGE] y presione el botón SET.
h Se abre la pantalla para seleccionar el idioma.
Seleccione el idioma de la pantalla deseado, y presione el botón
SET.
200 VQT3M88
Grabación
GRABACIÓN DE VÍDEO
1
Presione el botón [@].
h Se inicia la grabación.
h No es necesario mantener
presionado el botón [@]
durante la grabación de
videoclips.
Botón [@]
h Cuando el tiempo de grabación
restante disponible para la
grabación de vídeo efectivo llega
a 30 segundos o menos, en la
pantalla aparece una cuenta
regresiva del tiempo de
grabación restante.
2
Termine la grabación.
h Vuelva a presionar el botón
[@] para detener la grabación.
h El tiempo de grabación
transcurrido retorna a 000:00:00
cada vez que se detiene la
grabación.
Tiempo de grabación
transcurrido
(horas:minutos:
segundos)
p
001008:0-0300:09
2
M
5
Tiempo de grabación
restante disponible
(segundos)
VQT3M88 201
TOMA DE FOTOGRAFÍAS
1
Presione el botón [O].
1 Presione el botón [O] hasta
la mitad.
Botón [O]
h El enfoque automático se
pone en funcionamiento y se
enfoca la imagen (bloqueo
de enfoque).
2 Presione suavemente el
botón [O] hasta el final.
h El obturador se dispara y la
cámara captura la imagen.
1
2
-
S
16M
h Usted puede ver la imagen
capturada en la pantalla LCD
manteniendo presionado el
botón [O] cuando capture
la imagen.
F3.5
1/30
Marca de destino
202 VQT3M88
REPRODUCCIÓN DE FOTOGRAFÍAS Y VÍDEOS
1
2
Presione el botón REC/ para visualizar la pantalla de
reproducción.
Seleccione la imagen que desea
reproducir.
h Mueva el botón SET hacia arriba,
hacia abajo, a la izquierda o a la
derecha para desplazar el marco
amarillo hasta el archivo que desea
reproducir.
Información
de la
Marco amarillo
imagen
h La información de la imagen
enmarcada se muestra en la parte
inferior de la pantalla.
DEC.20.2011
6:41 PM
100-0006
00:00:05
10.5MB
SET
1080-60i
ENTER
<Pantalla de reproducción>
3
Presione el botón SET.
h La imagen seleccionada en el paso
2 aparece a pantalla LCD.
h Si se seleccionó un vídeo, empieza
la reproducción.
<Archivo de fotografía: Para volver
a la pantalla y seleccionar archivos
para su reproducción>
Mueva el botón SET hacia
abajo.
CONSEJO
i Las fotografías se pueden rotar durante
la reproducción.
i Si usted cierra la unidad de pantalla la
reproducción se detiene y la cámara se
conmuta al modo en espera.
Botón REC/
Botón SET
VQT3M88 203
Operación de reproducción de vídeos
Para hacer esto ...
Haga esto
Reproducción normal hacia Presione el botón SET o muévalo hacia
adelante
arriba.
Durante la reproducción, mueva el botón SET
hacia abajo.
Detener la reproducción
Durante la reproducción, presione el botón
SET o muévalo hacia arriba.
Durante la reproducción, mueva el botón SET
hacia arriba.
Hacer una pausa
Parareproducir
imágenes una
a una (pasos
de un solo
Durante la reproducción Después de hacer una pausa en la reproducción,
hacia adelante
mueva el botón SET hacia la derecha.
Durante la reproducción Después de hacer una pausa en la reproducción,
hacia atrás
mueva el botón SET hacia la izquierda.
Después de hacer una pausa en la
cuadro)
Durante la
reproducción reproducción, presione y mueva el botón SET
hacia adelante hacia la derecha, sin soltarlo.
Reproducción
lenta
Durante la
Después de hacer una pausa en la
reproducción reproducción, presione y mueva el botón SET
hacia atrás hacia la izquierda, sin soltarlo.
Durante la reproducción hacia adelante,
mueva el botón SET hacia la derecha.
Reproducción
hacia adelante
(Máximo 15×)
h
La velocidad de reproducción hacia adelante
cambia cada vez que se mueve el botón SET
hacia la derecha.
Mueva el botón SET hacia la izquierda para
volver a la velocidad de reproducción normal.
Durante la reproducción hacia adelante,
mueva el botón SET hacia la izquierda.
Para
acelerar la
reproducción
Reproducción h La velocidad de reproducción en retroceso
en retroceso
(Máximo 15×)
cambia cada vez que se mueve el botón
SET hacia la izquierda.
Mueva el botón SET hacia la derecha para
volver a la velocidad de reproducción normal.
Volver a la velocidad de
reproducción normal
Presione el botón SET.
Durante la reproducción, mueva el interruptor
Más alto
del zoom hacia [T/]].
Ajuste del
volumen
Durante la reproducción, mueva el interruptor
Más bajo
del zoom hacia [W/P].
204 VQT3M88
CONSEJO
Si aparece
i El icono
segmentos.
en la pantalla de reproducción ...
aparece cuando se reproduce un archivo guardado en
VQT3M88 205
Panasonic Consumer Electronics Company,
Division of Panasonic Corporation of North America
One Panasonic Way, Secaucus, NJ 07094
VQT3M88
M0411-0
1AG6P1P6280--(S)
© Panasonic Corporation 2011
Printed in Indonesia
|
