Panasonic CQ C800U User Manual

AAC WMA MP3 CD Player/Receiver

Récepteur/lecteur CD avec lecture AAC/WMA/MP3

Reproductor de CD, AAC, WMA y MP3/receptor

Model:

CQ-C800U

SOURCE

PWR

DIM

TUNE

TRACK

/SET/APM

BAND

TILT

FOLDER/P-SET/DISC

LIST

DISP

OPEN

MUTE

SBC-SW

・

Operatting Innstrucctions

Manueel d’innstrucctions

Manuaal de Innstruccciones

TEXT

¡Please read these instructions (including “Limited Warranty” and “Customer Services Directory”) carefully before using this product

and keep this manual for future reference.

¡Prière de lire attentivement ces instructions (y compris la “Garantie limitée” et le “Répertoire des services à la clientèle”) avant

d’utiliser ce produit et conserver ce manuel d’utilisation pour s’y référer ultérieurement.

¡Lea con atención estas instrucciones antes de utilizar el producto y guarde este manual para poderlo consultar en el futuro.

Safety Information

■

Read the operating instructions for the unit and all other com-

ponents of your car audio system carefully before using the

system. They contain instructions about how to use the sys-

tem in a safe and effective manner. Panasonic assumes no

responsibility for any problems resulting from failure to

observe the instructions given in this manual.

This manual uses pictographs to show you how to use the

product safely and to alert you to potential dangers resulting

from improper connections and operations. The meanings of

the pictographs are explained below. It is important that you

fully understand the meanings of the pictographs in order to

use this manual and the system properly.

This pictograph intends to alert you to the pres-

ence of important operating instructions and

This pictograph intends to alert you to the pres-

ence of important operating instructions and

installation instructions. Failure to heed the

instructions may result in injury or material dam-

age.

installation instructions. Failure to heed the

Warning

Caution

instructions may result in severe injury or death.

Observe the following warnings when

installing.

Warning

Observe the following warnings when using

this unit.

The driver should neither watch the display nor

operate the system while driving.

Watching the display or operating the system will distract

the driver from looking ahead of the vehicle and can cause

accidents. Always stop the vehicle in a safe location and use

the parking brake before watching the display or operating

the system.

❑

Disconnect the lead from the negative (–) battery

terminal before installation.

Wiring and installation with the negative (–) battery terminal

connected may cause electrical shock and injury due to a

short circuit.

❑

Some cars equipped with the electrical safety system have

specific procedures of battery terminal disconnection.

FAILURE TO FOLLOW THE PROCEDURE MAY LEAD TO THE

UNINTENDED ACTIVATION OF THE ELECTRICAL SAFETY

SYSTEM RESULTING IN DAMAGE TO THE VEHICLE AND

PERSONAL INJURY OR DEATH.

❑

Use the proper power supply.

This product is designed for operation with a negative

grounded 12 V DC battery system. Never operate this prod-

uct with other battery systems, especially a 24 V DC battery

system.

❑

Never use safety-related components for installa-

tion, grounding, and other such functions.

Do not use safety-related vehicle components (fuel tank,

brake, suspension, steering wheel, pedals, airbag, etc.) for

wiring or fixing the product or its accessories.

Keep batteries and insulation film out of reach of

infants.

Batteries and insulation film can be ingested, so keep them

out of the reach of infants. If an infant ingests a battery or

insulation film, please seek immediate medical attention.

Protect the Deck Mechanism.

Do not insert any foreign objects into the slot of this unit.

❑

Installing the product on the air bag cover or in a

location where it interferes with airbag operation is

prohibited.

Check for piping, gasoline tank, electric wiring, and

other items before installing the product.

If you need to open a hole in the vehicle chassis to attach or

wire the product, first check where the wire harness, gaso-

line tank, and electric wiring are located. Then open the hole

from outside if possible.

❑

Do not disassemble or modify the unit.

Do not disassemble, modify the unit or attempt to repair the

product yourself. If the product needs to be repaired, consult

your dealer or an authorized Panasonic Servicenter.

❑

Never install the product in a location where it inter-

❑

Do not use the unit when it is out of order.

If the unit is out of order (no power, no sound) or in an

abnormal state (has foreign objects in it, is exposed to

water, is smoking, or smells), turn it off immediately and

consult your dealer.

The remote control unit should not lie about in the

car.

If the remote control unit lies about, it could fall on the floor

while driving, get wedged under the brake pedal, and lead to

a traffic accident.

Refer fuse replacement to qualified service person-

nel.

When the fuse blows out, eliminate the cause and have it

replaced with the fuse prescribed for this unit by a qualified

service engineer. Incorrect replacement of the fuse may lead

to smoke, fire, and damage to the product.

feres with your field of vision.

Never have the power cord branched to supply other

equipment with power.

After installation and wiring, you should check the

normal operation of other electrical equipment.

The continuation of their using in abnormal conditions may

cause fire, electrical shock or a traffic accident.

❑

In the case of installation to an airbag equipped car,

confirm warnings and cautions of the vehicle manu-

facturer before installation.

❑

Make sure the leads do not interfere with driving or

getting in and out of the vehicle.

Insulate all exposed wires to prevent short circuit-

ing.

CQ-C800U

❑

Do not install the product where it is exposed to

strong vibrations or is unstable.

Caution

Avoid slanted or strongly curved surfaces for installation. If

the installation is not stable, the unit may fall down while

driving and this can lead to an accident or injury.

Observe the following cautions when using this

unit.

Keep the sound volume at an appropriate level.

Keep the volume level low enough to be aware of road and

traffic conditions while driving.

Do not insert or allow your hand or fingers to be

caught in the unit.

To prevent injury, do not get your hand or fingers caught in

moving parts or in the disc slot. Especially watch out for

infants.

This unit is designed for use exclusively in automo-

biles.

Do not operate the unit for a prolonged period with

the engine turned off.

Operating the audio system for a long period of time with the

engine turned off will drain the battery.

Installation Angle

❑

The product should be installed in a horizontal position with

the front end up at a convenient angle, but not more than

30˚.

❑

The user should bear in mind that in some areas there may

be restrictions on how and where this unit must be installed.

Consult your dealer for further details.

Wear gloves for safety. Make sure that wiring is

completed before installation.

To prevent damage to the unit, do not connect the

power connector until the whole wiring is complet-

ed.

Do not connect more than one speaker to one set of

speaker leads. (except for connecting to a tweeter)

❑

Do not expose the unit to direct sunlight or exces-

sive heat.

Observe the following cautions when handling

the battery for the remote control unit.

Otherwise these will raise the interior temperature of the

unit, and it may lead to smoke, fire, or other damage to the

unit.

●

Use only specified battery (CR2025).

Match the polarity of the battery with the (+) and (–) marks

in the battery case.

Do not use the product where it is exposed to water,

moisture, or dust.

Exposure of the unit to water, moisture, or dust may lead to

smoke, fire, or other damage to the unit. Make especially

sure that the unit does not get wet in car washes or on rainy

days.

●

Replace dead battery as soon as possible.

Remove the battery from the remote control unit when not

using it for an extended period of time.

Insulate the battery (by placing them in a plastic bag or cov-

ering them with vinyl tape) before disposal or storage.

Dispose of the battery according to the local regulations.

Do not disassemble, recharge, heat or short the battery. Do

not throw a battery into a fire or water.

●

Observe the following cautions when

installing.

❑

Refer wiring and installation to qualified service

personnel.

Installation of this unit requires special skills and experience.

For maximum safety, have it installed by your dealer.

Panasonic is not liable for any problems resulting from your

own installation of the unit.

Follow the instructions to install and wire the prod-

uct.

Not following the instructions to properly install and wire the

product could cause an accident or fire.

In case of battery leakage

●

Thoroughly wipe the battery liquid off the battery case and

insert new battery.

If any part of your body or clothing comes into contact with

battery liquid, wash it with plenty of water.

If battery liquid comes into contact with your eyes, wash

them with plenty of water and get immediate medical atten-

tion.

❑

Take care not to damage the leads.

When wiring, take care not to damage the leads. Prevent

them from getting caught in the vehicle chassis, screws, and

moving parts such as seat rails. Do not scratch, pull, bend or

twist the leads. Do not run them near heat sources or place

heavy objects on them. If leads must be run over sharp

metal edges, protect the leads by winding them with vinyl

tape or similar protection.

❑

Use the designated parts and tools for installation.

Use the supplied or designated parts and appropriate tools

to install the product. The use of parts other than those sup-

plied or designated may result in internal damage to the unit.

Faulty installation may lead to an accident, a malfunction or

fire.

Do not block the air vent or the cooling plate of the

unit.

Blocking these parts will cause the interior of the unit to

overheat and will result in fire or other damage.

CQ-C800U

Safety Information (continued)

The following applies only in the U.S.A.

Part 15 of the FCC Rules

Caution

THIS PRODUCT IS A CLASS I LASER PRODUCT.

USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE

OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN

MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

DO NOT OPEN COVERS AND DO NOT REPAIR BY YOURSELF.

REFER SERVICING TO QUALIFIED PERSONNEL.

FCC Warning:

Any unauthorized changes or modifications to this

equipment would void the user’s authority to operate

this device.

Notice

This product contains a CR Coin Cell Lithium Battery

which contains Perchlorate Material – special handling

may apply.

See www.dtsc.ca.gov/hazardouswaste/perchlorate.

Before Reading These Instructions

Panasonic welcomes you to our constantly growing family of electronic products owners.

We endeavor to give you the advantages of precise electronic and mechanical engineering, manufactured with carefully

selected components, and assembled by people who are proud of the reputation their work has built for our company. We

know this product will bring you many hours of enjoyment, and after you discover the quality, value and reliability we have

built into it, you too will be proud to be a member of our family.

CQ-C800U

Before Reading These Instructions (continued)

XXXXXXXXXXXXXXX

XXXXXXXXXXXXXXXXX

XXXXXXXXXXXXXX

XXXXXXXXXXXXXXX

XXXXXXXXXXXXXXXXX

XXXXXXXXXXXXXX

XXXXXXXXXXXXXXXX

OO-OOOOO

Operating

Instructions

System Upgrade

Guidebook

Installation

Instructions

Product

Registration Card

Customer Care

Plan

(YFM264C086CA)

(YFM264C087CA)

(YFM294C132CA)

Instruction kit

Q'ty: 1 set

POWER

SOURCE MENU

SEL

SRC

VOL

SET

BAND

MUTE

REPEAT

RANDOM SCAN

TUNE

NUMBER

DISP

CAR AUDIO

Power Connector

Mounting Collar

Trim Plate

Remote Control Unit

(including a battery)

(CR2025)

(YEFC051013)

(EUR7641010)

(YGAJ021009)

(FX0214C384ZB)

Q'ty: 1

Lock Cancel Plate

Mounting Bolt

Tapping Screw

Hex. Nut

(5 mmø)

(5 mmø x 16 mm)

(5 mmø)

(YEP0FZ5739)

Q'ty: 1 set

Notes:

¡ The number in parenthesis underneath each accessory

part name is the part number for maintenance and

service.

¡ Accessories and their parts numbers are subject to

modification without prior notice due to improve-

ments.

¡ Mounting Collar and Trim Plate are mounted on the

main unit at shipment.

Rear Support Strap

Removable Face

Plate Case

(YFG044C002ZA)

(YFC054C089CA)

Q'ty: 1

CQ-C800U

Before Reading These Instructions (continued)

U.S.A.

CANADA

Obtain Product Information and Operating Assistance;

locate your nearest Dealer or Servicenter; purchase

Parts and Accessories; or make Customer Service and

Literature requests by visiting our Web Site at:

http://www.panasonic.com/support

or, contact us via the web at:

http://www.panasonic.com/contactinfo

You may also contact us directly at:

1-800-211-PANA (7262),

WARRANTY SERVICE

FOR PRODUCT OPERATION ASSISTANCE, please con-

tact:

Our Customer Care Centre:

Telephone #:

1-800 #:

Fax #:

(905) 624-5505

1-800-561-5505

(905) 238-2360

“Contact Us” on

www.panasonic.ca

Email link:

Monday-Friday 9 am-9 pm; Saturday-Sunday 10 am-7

pm, EST.

FOR PRODUCT REPAIRS, please locate your nearest

Authorized Servicentre at www.panasonic.ca:

For hearing or speech impaired TTY users,

TTY : 1-877-833-8855

Accessory Purchases:

Link : “Servicentres locator” under “Customer sup-

Purchase Parts, Accessories and Instruction Books

online for all Panasonic Products by visiting our Web

Site at:

port”

http://www.pasc.panasonic.com

or, send your request by E-mail to:

[email protected]

You may also contact us directly at:

1-800-332-5368 (Phone) 1-800-237-9080 (Fax Only)

(Monday-Friday 9 am to 8 pm, EST.)

Panasonic Services Company

IF YOU SHIP THE PRODUCT TO A SERVICENTRE

Carefully pack and send prepaid, adequately insured and

preferably in the original carton.

Include details of the defect claimed, and proof of date

of original purchase.

20421 84th Avenue South, Kent, WA 98032

(We accept Visa, MasterCard, Discover Card, American

Express, and Personal Checks)

For hearing or speech impaired TTY users,

TTY : 1-866-605-1277

Service in Puerto Rico

Matsushita Electric of Puerto Rico, Inc.

Panasonic Sales Company

Factory Servicenter:

Ave. 65 de Infantería, Km. 9.5, San Gabriel Industrial

Park,

Carolina, Puerto Rico 00985

Phone (787) 750-4300, Fax (787) 768-2910

CQ-C800U

loss of media, data or other memory contents. The items listed are

not exclusive, but are for illustration only.) ALL EXPRESS AND

IMPLIED WARRANTIES, INCLUDING THE WARRANTY OF MER-

CHANTABILITY, ARE LIMITED TO THE PERIOD OF THE LIMITED

WARRANTY.

U.S.A.

PANASONIC CONSUMER ELECTRONICS COMPANY,

DIVISION OF PANASONIC CORPORATION OF NORTH AMERICA

One Panasonic Way, Secaucus, New Jersey 07094

Some states do not allow the exclusion or limitation of incidental or

consequential damages, or limitations on how long an implied war-

ranty lasts, so the exclusions may not apply to you.

PANASONIC SALES COMPANY,

DIVISION OF PANASONIC PUERTO RICO, INC.

Ave. 65 de infanteria, Km. 9.5, San Gabriel Industrial Park

Carolina, Puerto Rico 00985

This warranty gives you specific legal rights and you may also have

other rights which vary from state to state. If a problem with this

product develops during or after the warranty period, you may con-

tact your dealer or Servicenter. If the problem is not handled to your

satisfaction, then write to warrantor’s Consumer Affairs Department

at the addresses of the warrantor.

PANASONIC AUTO PRODUCTS

LIMITED WARRANTY

LIMITED WARRANTY COVERAGE

If your product does not work properly because of defects in materi-

als and workmanship.

PARTS AND SERVICE WHICH ARE NOT COVERED BY THIS LIMITED

WARRANTY ARE YOUR RESPONSIBILITY.

Panasonic Consumer Electronics Company or Panasonic Sales

Company (collectively referred to as “the warrantor”) will, for the

length of the period indicated in the chart below, which starts with

the date of original purchase (“warranty period”), at its option either

(a) repair your product with new or refurbished parts, or (b) replace

it with a new or refurbished product. The decision to repair or

replace will be made by the warrantor.

Customer’s Record

Model

No.

Serial

No.

Dealer’s

No.

Code

No.

Dealer’s

Address

Date of

Categories

Parts

Labor

Audio Components (except items listed

below)

MXE Series Audio Components (except

items listed below)

One (1) Year

Two (2) Years

One (1) Year

Two (2) Years

Not Applicable

Speakers

Defective Car Audio Speakers under war-

ranty must be exchanged at the place of

purchase. Contact your Dealer for details.

Purchase

Accessories (in exchange for defective

items)

Ninety (90) Days Not Applicable

CANADA

During the “Labor” warranty period, there will be no charge for

labor. During the “Parts” warranty period, there will be no charge for

parts. You must carry in or mail in your product prepaid during the

warranty period. If non rechargeable batteries are included, they are

not warranted. This warranty only applies to products purchased and

serviced in the United States or Puerto Rico. This warranty is

extended only to the original purchaser of a new product which was

not sold “as is”. A purchase receipt or other proof of the original

purchase date is required for warranty service.

Panasonic Canada Inc.

5770 Ambler Drive, Mississauga Ontario L4W 2T3

PANASONIC PRODUCT LIMITED

WARRANTY

Panasonic Canada Inc. warrants this product to be free from defects

in materials and workmanship and agrees to remedy any such defect

for a period as stated below from the date of original purchase.

CARRY-IN OR MAIL-IN SERVICE

For Carry-In or Mail-In Service in the United States, call 1-800-211-

PANA (7262) or visit

Panasonic Web Site: http://www.panasonic.com

For assistance in Puerto Rico, call Panasonic Sales Company (787)-

750-4300 or fax (787)-768-2910.

CAR AUDIO PRODUCT – ONE (1) YEAR, PARTS AND LABOUR

(The labour to install or remove the product is not warranted)

ACCESSORIES - NINETY (90) DAYS, (IN EXCHANGE FOR DEFEC-

TIVE ITEMS)

LIMITED WARRANTY LIMITS AND EXCLUSIONS

LIMITATIONS AND EXCLUSIONS

This warranty ONLY COVERS failures due to defects in materials and

workmanship, and DOES NOT COVER normal wear and tear or cos-

metic damage. The warranty ALSO DOES NOT COVER damages

which occurred during shipment, failures which are caused by prod-

ucts not supplied by the warrantor, failures which result from acci-

dent, misuse, abuse, neglect, bug infestation, mishandling, misappli-

cation, alteration, faulty installation, set-up adjustment, maladjust-

ment of consumer control, improper maintenance, improper anten-

na, inadequate signal reception or pickup, power line surge, improp-

er voltage supply, lightning, modification, commercial use (such as

use in hotels, offices, restaurants, or other business uses) or rental

use of the product, or service by anyone other than the technician

from Factory Servicenter or other authorized service centers, or

damage that is attributable to acts of God.

This warranty does not apply to products purchased outside Canada

or to any product which has been improperly installed, subjected to

usage for which the product was not designed, misused or abused,

damaged during shipping, or which has been altered or repaired in

any way that affects the reliability or detracts from the performance,

nor does it cover any product which is used commercially. Dry cell

batteries are also excluded from coverage under this warranty.

This warranty is extended to the original end user purchaser only. A

purchase receipt or other proof of the original purchase date is

required before warranty service is performed.

THIS EXPRESS, LIMITED WARRANTY IS IN LIEU OF ALL OTHER

WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PAR-

TICULAR PURPOSE.

IN NO EVENT WILL PANASONIC CANADA INC. BE LIABLE FOR ANY

SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES.

In certain instances, some jurisdictions do not allow the exclusion or

limitation of incidental or consequential damages, or the exclusion of

implied warranties, so the above limitations and exclusions may not

be applicable.

THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED

UNDER “LIMITED WARRANTY COVERAGE”. THE WARRANTOR IS

NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES

RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT

OF ANY BREACH OF THIS WARRANTY. (As examples, this excludes

damages for lost time, cost of having someone remove or re-install

an installed unit if applicable, travel to and from the servicer, and

CQ-C800U

Features

Compatible with the AAC format

Sound Control

This unit has newly become compatible with AAC-formatted

files in addition to the existing MP3 and WMA files.

SQ (Sound Quality)

You have six preset modes (FLAT, ROCK, POP, VOCAL, JAZZ,

CLUB). You can customize your settings for these and save

them for instant recall.

Note: Some of AAC files (such as SD-Jukebox type) are not

playable.

SQ7

Hands-Free Phone System

This is 7-band equalizer with 60, 160, 400, 1 k, 3 k, 6 k, and 16 kHz.

Each band is adjustable between – 12 dB and 12 dB in steps of

2 dB.

Connection of the optional Hands-Free Phone System (Hands-

Free Kit featuring Bluetooth technology: CY-BT100U) allows

users to talk on a handsfree cellular phone if the phone

supports Bluetooth.

D·M

Note: This unit is designed only for receiving calls. It cannot

You can assign your favorite broadcasting station to the

[D·M] button. As the result of doing that, your favorite

broadcasting station can be received even if the unit is in

the CD mode or other modes. (apage 20)

send calls.

Bluetooth

The Bluetooth word mark and logo are owned by the

Bluetooth SIG, Inc. and any use of such marks by

Matsushita Electric Industrial Co.,Ltd. is under license.

Other trademarks and trade name are those of their

respective owners.

Customize

Initially stored moving images and still images are editable to

taste. IMAGE STUDIO* allows you to process images from a

digital camera or other devices without difficulty. (apage 31)

* This software is downloadable from Panasonic Web site

Expansion Module (hub unit)

Connection of the Expansion Module (hub unit, CY-EM100U)

allows users to connect up to 4 optional devices shown below.

Even simultaneous connection of the Sirius Satellite Radio and

XM Satellite Radio is feasible.

(http://panasonic.co.jp/pas/en/software/customize/index.html

)

Note: A hub unit is not required to connect only one optional

component.

Wide array of components for system upgrade

Various optional components allow users to obtain availability

of wide range of system upgrade. Upgrading the system

delivers relaxed AV space in a car. For further information, refer

to the separate System Upgrade Guidebook.

¡ DVD Changer

The optional adapter (Conversion Cable for DVD/CD

Changer: CA-CC30U) allows you to connect the option-

al Panasonic DVD changer unit (CX-DH801U).

¡ CD Changer

The optional adapter (Conversion Cable for DVD/CD

Changer: CA-CC30U) allows you to connect the option-

al Panasonic CD changer unit (CX-DP880U).

¡ iPod

The optional adapter (Direct Cable for iPod: CA-DC300U

allows you to connect the optional iPod series.

iPod is a trademark of Apple Computer, Inc., registered in

the U.S. and other countries.

)

¡ XM Satellite Radio

You can connect the optional XM receiver (XMD-1000)

with optional Digital Adapter. For details, refer to the

operating instructions for the XM receiver.

¡ Sirius Satellite Radio

You can connect the optional Sirius Satellite radio

receiver (SIR-PAN1).

CQ-C800U

Contents

English

Français

Español

¡Safety Information

¡Before Reading These Instructions

¡Features

¡Controls Layout

¡Preparation (Clock adjustment etc.)

¡General

¡Sound Control

¡Radio

¡CD Player

¡MP3/WMA/AAC Player

¡Audio Setting

¡Function Setting (Security Function Setting etc.)

¡Display Setting

¡Customize the Display (Customize Function)

¡Troubleshooting

¡Error Display Messages

¡Notes on Discs

¡Maintenance/Fuse

¡Specifications

CQ-C800U

Controls Layout

Note: This instruction manual explains operations for use with the buttons on the main unit. (Different operations excluded)

SQ Sound Quality (apage 19)

MENU (apage 29, 30)

SOURCE Source

PWR Power

(apage 14, 16)

DIM Dimmer (apage 17)

u OPEN (eject)

(apage 15)

TILT

(apage 15)

TUNE

(apage 20)

TRACK (FILE)

(apage 22, 24)

Remote Control

Sensor

CQ-C800U

SOURCE

PWR

DIM

TUNE

TRACK

VOL

/SET/APM

BAND

TILT

FOLDER/P SET/DISC

(apage 15)

PUSH SEL Select

DISP

OPEN

MUTE

・

SBC SW

LIST

(apage 28)

SRS WOW

(apage 18)

DISP Display

P-SET Preset (apage 21)

(apage 17)

DISC (aSystem Upgrade

Guidebook, page 8, 10)

FOLDER (apage 24)

LIST (aSystem Upgrade

Guidebook, page 12)

Release

(apage 14)

MUTE (apage 15)

BAND (apage 20)

SBC-SW Super Bass

Control-Subwoofer

(apage 19)

Pause/Play

(apage 22, 24)

APM Auto Preset Memory

(apage 21)

D·M Direct Memory

(apage 20)

Disc slot

CQ-C800U

Number Buttons

0 to 9

–

VOL Volume

}:Up

SEL Select

NUMBER

{:Down

Number

POWER

SRC (SOURCE)

RANDOM

POWER

SOURCE

SEL

SRC

SCAN

VOL

SCAN

SET

BAND

MUTE

BAND

Pause/Play

SET

APM Auto Preset

Memory

MUTE

REPEAT

SBC-SW Super Bass

Control-Subwoofer

REPEAT

RANDOM SCAN

TUNE

DISP

NUMBER

DISP Display

TUNE

TRACK (FILE)

CAR AUDIO

P·SET (Preset)

DISC (FOLDER)

Although most of the functions of this unit are executable

with both the main unit and remote control, the following

functions are excluded.

Operations executable only with main uni

¡Face panel’s opening, closing, tilting, and removal

actions (apage 15)

¡Disc ejection (apage 15)

¡Dimmer (apage 17)

¡SRS WOW on, off, and adjustment (apage 18)

¡SQ on, off, and adjustment (apage 19)

¡Direct memory setting and calling (apage 20)

Operations executable only with remote control

¡Preset station calling with one-touch operation

(apage 21)

¡Direct access to tracks on CDs (apage 23, 25)

¡Random and repeat play with one-touch operation

(apage 23, 25)

¡Scan playback (apage 23, 25)

CQ-C800U

Preparation

For the first use, the following screen may appear

repeatedly.

Turn [VOL] to select

“DEMONSTRATION”.

For using the remote control, use [}] or [{].

Set your car’s ignition switch to the ACC

or On position.

The demonstration screen appears.

Press [PUSH SEL] to select “OFF”.

Press [SOURCE] (PWR: POWER).

For using the remote control, use [BAND] (SET).

Press [MENU] to display the menu

display.

For using the remote control, hold down [SEL]

(MENU) for 2 sec. or more.

Press [MENU] to close the menu

screen.

For using the remote control, hold down [SEL]

(MENU) for 2 sec. or more.

Press []] or [[] to display the

DISPLAY menu.

Note: This unit is operable as usual even if the

demonstration screen is activated. The demonstration

screen automatically appears if no operation is executed

for 1 minute.

Preparation Before Initial Use

Warning

Keep batteries and insulation film out of reach of

infants. If an infant ingests a battery, please seek

immediate medical attention.

Pull the insulation film out

from the backside of

remote control gently.

Cautions

Insulation film

¡Remove and dispose of an old battery immediately.

¡Do not disassemble, heat or short a battery. Do not

throw a battery into a fire or water.

Battery Replacement

Tough pointed object

q Remove the battery holder

with the remote control unit

placed on a flat surface.

q Stick your thumbnail into

the groove, and push the

holder in the direction of

the arrow, and at the

same time.

w Pull it out in the direction

of the arrow using a

¡Follow local regulations when disposing of a battery.

¡Improper use of a battery may cause overheating, an

explosion or ignition, resulting in injury or a fire.

Notice

This product contains a CR Coin Cell Lithium

Battery which contains Perchlorate Material –

special handling may apply.

See www.dtsc.ca.gov/hazardouswaste/perchlorate.

tough pointed object.

Back side

Note: Battery Information:

Battery Type: Panasonic lithium battery (CR2025)

(Included in the remote control)

Battery Life: Approximately 6 months under normal use

(at room temperature)

w Put a battery in the case

with (+) side facing up.

e Put the case back.

CQ-C800U

The following functions are activated when the Security

Function is ON. (a page 29)

¡The security indicator lights up when removing the

¡The alarm sounds and the message appears on the

screen to warn you to remove the face plate at ACC

off.

face plate.

Security Indicator

You may need to set the following depending on the

devices to be connected.

Using Subwoofer

¡Subwoofer level adjustment (apage 28)

¡Subwoofer low pass filter (apage 28)

Note: Other settings are required when a Sirius receiver,

an XM receiver, or a Hands-Free Phone System is

connected. (aSystem Upgrade Guidebook)

Note: Adjust the clock when “ADJUST” appears on the

display.

Adjust the setting value.

Press [MENU] to display the menu

display.

[[]

Adjusting minutes

Adjusting hours

Forward

For using the remote control, hold down [SEL]

(MENU) for 2 sec. or more.

[]]

Press []] or [[] to display the

Backward

DISPLAY menu.

Press [PUSH SEL], and the menu

screen resumes.

Turn [VOL] to select “CLOCK ADJ”.

For using the remote control, use [}] or [{].

Press [PUSH SEL], and the clock

adjustment screen appears.

For using the remote control, use [BAND] (SET).

Press [MENU] to close the menu

screen.

For using the remote control, use [BAND] (SET).

For using the remote control, hold down [SEL]

(MENU) for 2 sec. or more.

CQ-C800U

General

This chapter explains how to turn on or off the power, how to adjust the volume, etc.

Power on

CQ-C800U

SOURCE

PWR

Press [SOURCE] (PWR: POWER).

DIM

TUNE

TRACK

/SET/APM

BAND

TILT

FOLDER/P-SET/DISC

LIST

DISP

OPEN

MUTE

SBC-SW

・

Power off

Hold down [SOURCE] (PWR: POWER) until

you hear a beep, then release it.

You can remove the face

plate to prevent it from

being stolen.

Mounting

Removing

Slide the left side of the face plate in

place.

Turn off the power (apage 14)

Press [

]

(Release).

CQ-C800U

(The face plate disen-

gages with a click

when it is removed.)

/SET/APM

BAND

TILT

DISP

OPEN

The face plate automatically closes after a lapse of 5

seconds while it is open.

The power is automatically turned off while the unit

is active.

Press the right end of the face plate

until “click” is heard.

Put the face

plate in the case.

¡Do not place the face plate on the dashboard or

nearby areas where the temperature rises to high

levels.

¡Do not touch the contacts on the face plate or on the

main unit, since this may result in poor electrical

contacts.

Cautions

¡It is recommended to remove or mount the face

plate when the plate is at the closed position.

Do not remove or mount the face plate when the

plate is in motion.

¡If dirt or other foreign substances get on the con-

tacts, wipe them off with clean and dry cloth.

¡To avoid damaging the face plate, do not push it

down or place objects on it while it is open.

¡This face plate is not waterproof. Do not expose it to

water or excessive moisture.

¡Do not remove the face plate while driving your car.

CQ-C800U

Open/Eject

Press [uOPEN].

CQ-C800U

SOURCE

PWR

When a disc is already loaded, the disc will automatically

be ejected.

DIM

TUNE

TRACK

/SET/APM

BAND

TILT

FOLDER/P-SET/DISC

LIST

DISP

OPEN

MUTE

SBC-SW

・

Tilt

Cautions

The display angle changes among 4 levels as follows

every time you hold down [uOPEN] (TILT) for 1 sec.

or more and release.

¡To avoid damaging the face plate, do not push it

down or place objects on it while it is open.

¡Do not pinch your finger or hand in the face plate.

¡Do not insert foreign objects into the disc slots.

¡For the following cases, the face plate automatical-

ly closes. Use caution not to catch your finger.

¡After a lapse of 20 seconds

¡When a disc is inserted

¡When the face plate is removed (apage 14)

¡When ACC is set to off

Note: The last selected

angle is memorized even

after turning off the power.

TILT 1

TILT 2

TILT 3

OPEN

Press [uOPEN].

TILT OFF

q Up

w Down

Notes:

¡The volume level can be set independently for each

source. (For radio, one volume setting for AM, one

volume setting for all FMs)

¡The volume is not adjustable while an error or the

menu screen is present on the monitor

Setting Range: 0 to 40

Default: 18

¡This unit memorizes individual volume levels for each

source. Make volume adjustments of each source

appropriately to prevent large volume fluctuation when

the source is changed.

Volume off (down)

Press [MUTE].

CQ-C800U

SOURCE

PWR

DIM

TUNE

TRACK

Cancel

/SET/APM

BAND

TILT

FOLDER/P-SET/DISC

LIST

DISP

OPEN

MUTE

SBC-SW

・

Press [MUTE] again.

Note:

Volume-down range can be specified.

page 29)

(

CQ-C800U

General (continued)

The source changes as follows every time

[SOURCE] is pressed.

CQ-C800U

SOURCE

PWR

DIM

TUNE

TRACK

/SET/APM

BAND

TILT

FOLDER/P-SET/DISC

LIST

DISP

OPEN

MUTE

SBC-SW

・

Radio

System-up Connector

FM1, FM2, FM3, AM (apage 20)

Device connected to the System-up Connector of this

unit

When optional devices are connected:

Shift to connected devices

When an expansion module is connected:

The devices connected to the ports 1 to 4 are activated

in sequence after shifting to AUX2 (devices connected

to the AUX terminal of the expansion module).

Player

When loading CD (apage 22)

When connecting DVD Changer

When connecting CD Changer

When connecting iPod

When loading a disc containing compressed

audio files (apage 24)

AUX 1

Device connected to the AUX terminal of the this unit

When connecting XM Receiver

When connecting Sirius Receiver

When connecting Expansion Module

Note: For information about connectable devices, refer

to the System Upgrade Guidebook or the instruction

manual for each device.

CQ-C800U

The display changes as follows every time [DISP:

DISPLAY] is pressed.

Note: The graphic pattern and still image are selectable.

(apage 30)

CQ-C800U

SOURCE

PWR

DIM

TUNE

TRACK

/SET/APM

BAND

TILT

FOLDER/P-SET/DISC

LIST

DISP

OPEN

MUTE

SBC-SW

・

At power-on:

Mode

Display OFF

All displays disappear in 5 seconds.

Ordinary display + clock

Only still image

Folder hierarchy (Compressed Audio Player mode only.)

Ordinary display + graphic pattern

Only graphic pattern

Ordinary display + still image

At power-off:

Clock display (default)

Off

The dimmer level changes as follows every time you hold

down [MENU] (DIM: DIMMER) for 2 sec. or more.

CQ-C800U

SOURCE

PWR

Brighter (default)

DIM

TUNE

TRACK

/SET/APM

BAND

TILT

FOLDER/P-SET/DISC

LIST

DISP

OPEN

MUTE

SBC-SW

・

Medium

Darker

Note: This setting is not adjustable with the remote

control.

CQ-C800U

Sound Control

SRS and SQ that provide users with simple adjustment of sound quality are described on this page. Audio Setting (apage 28) allows

users to adjust each speaker and the optional subwoofer in more detail (regarding BASS, TREBLE, BALANCE, FADER, SUB.W, LPF,

HPF, REAR).

SRS WOW™ is 3-D sound technology based on the HRTF

(Head Related Transfer Function) theory. Unlike

CQ-C800U

SOURCE

PWR

conventional audio systems, “natural 3-D sound field”,

“rich bass”, and “crisp and clear sound” can be obtained

at the same time in a wide area in front of speakers.

DIM

TUNE

TRACK

/SET/APM

BAND

TILT

FOLDER/P-SET/DISC

LIST

DISP

OPEN

MUTE

SBC-SW

・

Holding down [VOL] (SRS WOW) for 2 sec. or more

toggles SRS WOW on and off.

Note: If you enable SRS WOW, the following functions

are automatically disabled:

SQ, BASS/TREBLE, BALANCE/FADER, HPF, SBC-SW

Lights when SRS WOW is activated.

SRS TruBass^®

You can make a fine adjustment to SRS WOW.

Set the SRS WOW mode to on.

: Deep bass enhancement by application of the bass

reproduction technique of a pipe organ (default)

Hold down [SQ] for 2 sec. or more to

display “SRS WOW MENU”.

: No enhancement

SOURCE

PWR

SRS FOCUS^®

DIM

TUNE

TRACK

Sound image movement in a vertical direction to make

sound crisp

FOLDER/P-SET/DISC

LIST

MUTE

SBC-SW

・

: high (default)

: low

: off

Turn [VOL] to select a function to be

adjusted.

For using the remote control, use [}] or [{].

Press [PUSH SEL] to adjust.

For using the remote

SRS^®

: Surround function on (default)

: Surround function off

control, use [BAND]

(SET).

is a trademark of SRS Labs, Inc.

SOURCE

PWR

DIM

WOW technology is incorporated under license

from SRS Labs, Inc.

TUNE

TRACK

FOLDER/P-SET/DISC

LIST

MUTE

SBC-SW

・

Press [DISP: DISPLAY] to close the

menu screen.

CQ-C800U

The equalizer curve is selectable from among preset 6

types (FLAT, ROCK, POP, VOCAL, JAZZ, and CLUB)

depending on your listening category.

CQ-C800U

SOURCE

PWR

DIM

TUNE

TRACK

Note: SQ is not changeable when SRS WOW is enabled.

(apage 18)

/SET/APM

BAND

TILT

FOLDER/P-SET/DISC

LIST

DISP

OPEN

MUTE

SBC-SW

・

SQ changeover

The SQ category is changed every time [SQ] (Sound

Quality) is pressed.

Note: Setting of SQ, bass/treble and volume are

influenced one another. If the influence mentioned above

causes distortion to the audio signal, readjust bass/treble

or volume. (apage 28)

Lights when SQ is activated.

SQ is adjustable in accordance with your taste.

CQ-C800U

SOURCE

PWR

Hold down [SQ] (Sound Quality) for 2 sec.

or more to display “SOUND QUALITY

MENU” when SRS WOW is disabled.

DIM

TUNE

TRACK

/SET/APM

BAND

TILT

FOLDER/P-SET/DISC

LIST

DISP

OPEN

MUTE

SBC-SW

・

“USER” appears in the category name after adjust-

ment.

Press [PUSH SEL].

The targeted SQ preset appears.

For using the remote control, use [BAND] (SET).

Note: If [PUSH SEL] is held down for 2 sec. or

more on the "SQ ADJUSTMENT" display, the preset

data that is called up can be turned into the default.

Adjust each band.

Band: 60, 160, 400, 1 k, 3 k, 6 k, 16 k (Hz)

Press [PUSH SEL].

The screen of Step 1 appears again.

For using the remote control, use [BAND] (SET).

Press [DISP: DISPLAY].

[]] [[] : Band selection

q w :

Level up/down

The regular screen appears again.

The rear speaker can be used as a substitutional

subwoofer when a subwoofer is not connected.

CQ-C800U

SOURCE

PWR

Holding down [SBC-SW] for 2 sec. or more

toggles SBC-SW on and off.

DIM

TUNE

TRACK

/SET/APM

BAND

TILT

FOLDER/P-SET/DISC

LIST

DISP

OPEN

Off (default)

MUTE

SBC-SW

・

Lights when SBC-SW is activated.

Notes:

¡If ON is selected, the settings of subwoofer level

adjustment and subwoofer low pass filter are activat-

ed. (apage 28)

¡SBC-SW is not changeable when SRS WOW is

enabled. (apage 18)

CQ-C800U

Radio

This chapter explains how to listen to the radio.

CQ-C800U

Press [SOURCE] to select the radio

SOURCE

PWR

mode.

DIM

TUNE

TRACK

/SET/APM

BAND

TILT

FOLDER/P-SET/DISC

LIST

DISP

OPEN

MUTE

SBC-SW

・

Press [BAND] to select a band.

Preset station selection

[{] (P-SET: Preset): Lower preset number

Select a station.

[}] (P-SET: Preset): Higher preset number

Frequency adjustment

Notes:

¡ Direct selection can be executed with [1] to [6]

buttons on remote control.

¡ A preset station is selectable by turning [VOL]

while the preset list screen is present on the mon-

itor.

[]] (TUNE): Lower

[[] (TUNE): Higher

Note: Hold down for 0.5 sec. or more and release

for station search.

¡ The volume is not adjustable while the preset list

screen is present on the monitor.

Band

Frequency

Lights while receiving an FM stereo signal.

Preset Number

You can assign your favorite broadcasting station to

the [D·M] button. As the result of doing that, your

favorite broadcasting station can be received even if

the unit is in the CD mode or other modes. (Default:

FM 87.9 MHz)

CQ-C800U

SOURCE

PWR

DIM

TUNE

TRACK

/SET/APM

BAND

TILT

FOLDER/P-SET/DISC

LIST

DISP

OPEN

MUTE

SBC-SW

・

Note: For the use of an FM transmitter, it is useful

for users to register applicable frequencies on D·M

(Direct Memory).

D·M station Calling

Press [D·M] (DIRECT MEMORY).

Note: If the unit is turned off during receiving a broad-

casting station via D·M, the unit starts again receiving

the broadcasting station via D·M by turning on the unit.

D·M station Setting

q Select a station you would like to preset.

w Hold down [D·M] (DIRECT MEMORY) for 2 sec.

or more.

CQ-C800U

Up to 6 stations can be preset in AM, FM1, FM2, and FM3

respectively.

Manual station preset

Preset stations can be simply called up by pressing [}]

Tune in to a station.

(P-SET) or [{] (P-SET).

Hold down [}] or [{] for 2 sec. or

Notes:

more.

¡Direct selection can be executed with [1] to [6] but-

tons on remote control.

¡You can switch between 6 and 18 for FM presetting

stations. (EACH BAND/ALL BAND)

Turn [VOL] to select a preset number.

Hold down [PUSH SEL] for 2sec. or

more, and the frequency is stored at the

selected preset number.

¡Preset stations are changeable. (Preset Swap)

Auto Preset Memory (APM)

Stations with good receiving conditions automatically

preset.

Notes:

¡In step 2, a station can be registered by holding down

the numeric button [1] to [6] for 2 sec. or more.

¡To stop presetting stations, press [DISP:

DISPLAY].

¡The operation above allows users to replace the cur-

rent station with the station preset in the selected

number while selecting a preset station. (Preset Swap)

CQ-C800U

Select a band.

Hold down

/SET/APM

BAND

TILT

DISP

OPEN

[BAND] (APM)

for 2 sec. or

more.

The preset stations under best receiving conditions

are received for 5 sec. each after presetting the sta-

tions (SCAN). To stop scanning, press [}] or [{].

Note: New stations overwrite existing saved stations.

Press [MENU] to display the menu dis-

play.

Press [MENU] to close the menu

screen.

For using the remote

For using the remote control, hold down [SEL]

(MENU) for 2 sec. or more.

SOURCE

PWR

control, hold down

[SEL] (MENU) for 2

sec. or more.

DIM

TUNE

TRACK

FOLDER/P-SET/DISC

LIST

PRESET

MUTE

SBC-SW

・

Preset range for FM bands

: Individual setting for FM1-3 each

(default)

: Setting of FM1-3 together

Press [PUSH SEL] to adjust.

For using the remote

control, use [BAND]

(SET).

SOURCE

PWR

DIM

TUNE

TRACK

FOLDER/P-SET/DISC

LIST

MUTE

SBC-SW

・

CQ-C800U

CD Player

Cautions

¡This unit does not support 8 cm (3”) discs.

¡Do not use irregularly shaped discs. (apage 38)

¡Do not use discs that have a seal or label attached.

¡To avoid damaging the face plate, do not push it down or

place objects on it while it is open.

¡Refer to the section on “Notes on CD/CD Media (CD-ROM,

CD-R, CD-RW)” (apage 38).

¡This unit does not support a MIX mode CD (a CD containing

both CD-DA and compressed audio data). In case of using

such a CD, problems may occur such as anacoustic play-

back.

¡Do not pinch your finger or hand in the face plate when the

face plate is in motion.

¡Do not insert foreign matter into the disc slots.

When a disc is already loaded, press [SOURCE] to

select the CD mode.

CQ-C800U

SOURCE

PWR

Press [uOPEN] to open the face plate.

DIM

TUNE

TRACK

When a disc is already loaded (

lights), the

/SET/APM

BAND

TILT

FOLDER/P-SET/DISC

LIST

DISP

OPEN

MUTE

SBC-SW

・

disc will automatically be ejected.

Load a disc with the printed side facing

up.

Select a desired portion.

The face plate closes automatically, and the unit rec-

ognizes the disc and starts playing automatically,

too.

Track selection

[7] (TRACK): Next track

[6] (TRACK): Preceding track (press twice)

Note: Hold down for fast forward/reverse.

Printed side

Pause

Press [BAND] (

Press again to cancel.

Press [uOPEN] to eject the disc.

Note: The panel automatically closes after 20 sec-

onds.

Track number

Time

CD-TEXT display

Notes:

Play Mode indicators

Lights when the disc is

loaded.

Lights when each mode is

activated.

¡For scrolling text, hold down [DISP: DISPLAY] for 2

sec. or more.

¡“NO TEXT” is displayed when there is no information

on the disc.

CQ-C800U

Random and Repeat play can be set.

RANDOM

Press [MENU] to display the menu dis-

play.

: Off (default)

: Random playback

For using the remote

SOURCE

PWR

control, hold down

[SEL] (MENU) for 2

sec. or more.

DIM

TUNE

TRACK

REPEAT

FOLDER/P-SET/DISC

LIST

MUTE

SBC-SW

・

: Off (default)

: Playing the current track repeatedly

TEXT (CD-TEXT)

: Enabled (default)

: Disabled

Turn [VOL] to select a function to be

adjusted.

For using the remote

SOURCE

PWR

control, use [}] or

DIM

[{].

TUNE

TRACK

FOLDER/P-SET/DISC

LIST

MUTE

SBC-SW

・

Press [PUSH

SEL] to adjust.

For using the remote control, use [BAND] (SET).

Press [MENU] to close the menu

screen.

For using the remote control, hold down [SEL]

(MENU) for 2 sec. or more.

Play Mode Selection

SCAN play

One-touch operation is available for selecting a track

playing style by use of [RANDOM] or [REPEAT].

You can find your favorite track by playing first 10-sec. of

each track.

Press [SCAN].

RANDOM

Press [RANDOM].

Press again to cancel.

Direct Access

A track can be directly selected.

REPEAT

Press [REPEAT].

Press again to cancel.

Example: track number 5

Press [#] (NUMBER).

Press [5].

Press [SET].

Note: To suspend direct

selection, press [DISP] (DISPLAY).

CQ-C800U

MP3/WMA/AAC Player

This unit can play MP3, WMA, and AAC files.

When a disc is already loaded, press [SOURCE] to

select the compressed audio mode.

CQ-C800U

SOURCE

PWR

Press [uOPEN] to open the face plate.

DIM

TUNE

TRACK

When a disc is already loaded (

lights), the disc

/SET/APM

BAND

TILT

FOLDER/P-SET/DISC

LIST

DISP

OPEN

MUTE

SBC-SW

・

will automatically be ejected.

Load a disc with the printed side facing

up.

The face plate closes automatically, and the unit rec-

ognizes the disc and starts playing automatically,

too. (It may take several minutes to start for a disc

that has a lot of files.)

Select a desired portion.

Folder selection

[}] (FOLDER): Next folder

[{] (FOLDER): Preceding folder

File selection

[7] (TRACK): Next file

Printed side

[6] (TRACK): Preceding file (press twice)

Note: Hold down for fast forward/reverse.

Pause

Press [BAND] (

Press again to cancel.

Press [uOPEN] to eject the disc.

Note: The panel automatically closes after 20 sec-

onds.

File number

Time

Folder number

File type indicator

Information Display

Notes:

Play Mode indicators

Lights when the disc is

loaded.

Lights when each mode is

activated.

¡For scrolling text, hold down [DISP: DISPLAY] for 2

sec. or more.

¡“NO TEXT” is displayed when there is no information

on the disc.

(Folder Random)

(Folder Repeat)

(Folder Scan)

CQ-C800U

Notes:

¡Refer to the pages 26 and 27 for cautions.

¡This unit does not support a MIX mode CD (a CD containing both CD-DA and compressed audio files). In case of using such a

CD, problems may occur such as anacoustic playback.

Random and Repeat play can be set.

FOLDER RANDOM

Press [MENU] to display the menu dis-

play.

: Off (default)

: Random playback (folder)

For using the remote

SOURCE

PWR

control, hold down

[SEL] (MENU) for 2

sec. or more.

REPEAT

DIM

TUNE

TRACK

FOLDER/P-SET/DISC

LIST

: Off (default)

MUTE

SBC-SW

・

: Playing the current file repeatedly

Turn [VOL] to select a function to be

adjusted.

FOLDER REPEAT

: Off (default)

For using the remote con-

trol, use [}] or [{].

SOURCE

PWR

: Playing the current folder repeatedly.

DIM

TUNE

TRACK

TEXT

Press [PUSH

FOLDER/P-SET/DISC

LIST

MUTE

SBC-SW

・

SEL] to adjust.

: Folder name/File name (default)

Album/Title/Artist (tag information)

: No display

For using the remote control, use [BAND] (SET).

Press [MENU] to close the menu

screen.

RE-MASTER

For using the remote control, hold down [SEL]

(MENU) for 2 sec. or more.

The high-range signal lost through MP3/WMA/AAC

compression is reproduced to more closely recreate the

pre-compressed sound.

Notes:

¡At high bit rates, the Re-master function may have

little effect.

¡The Re-master function is only effective for playback

of MP3/WMA/AAC data.

RANDOM

: Digital sound enhancer activated (default)

: Digital sound enhancer inactivated

: Off (default)

: Random playback (disc)

FOLDER SCAN (1st file in each folder)

Hold down [SCAN] for 2 sec. or more. Hold down

again to cancel.

Play Mode Selection

One-touch operation is available for selecting a file

playing style by use of [RANDOM] or [REPEAT].

Direct Access

A file in the current folder can be directly selected.

RANDOM, REPEAT

Press the button. Press again to cancel.

Example: file number 5

FOLDER RANDOM, FOLDER REPEAT

Hold down the button for 2 sec. or more. Hold

down again to cancel.

Press [#] (NUMBER).

Press [5].

Press [SET].

SCAN play

Notes:

¡For folder selection, enter a number after pressing [#]

(NUMBER) twice.

You can find your favorite file by playing first 10-sec. of

each file.

¡To suspend direct selection, press [DISP]

(DISPLAY).

SCAN (All files)

Press [SCAN]. Press again to cancel.

CQ-C800U

MP3/WMA/AAC Player (continued)

Each of MP3 (MPEG Audio Layer-3), WMA (Windows Media™ Audio), and AAC (Advanced Audio Coding) is a format

for compressed audio file. These formats allow users to save all the files contained in approximately 10 pieces of

existing CDs on one piece of CD-R/RW.

Note: Each of encoding software is not included with this unit.

Setting at file making

Common

WMA

¡High bit rate and high sampling frequency are recom-

mended for high quality sounds.

¡It is recommended to set the bit rate to “64 kbps or

more” and “fixed”.

¡Selecting VBR (Variable Bit Rate) is not recommended ¡Do not set the copy protect attribute on the WMA file

because playing time is not displayed properly and

sound may be skipped.

The playback sound quality differs depending on the encod-

ing circumstances. For details, refer to the user manual of

your own encoding software and writing software.

Be sure to put an extension compatible with the format.

to enable this unit to play back.

AAC

¡It is recommended to set the bit rate to “128 kbps or

more” and “Stereo”.

¡Files with the extension of “.m4a” encoded using

iTunes version 6 are playable on this unit. Some of the

files using other encoders are not playable.

¡Files encoded using Apple Lossless Encoder are not

playable.

MP3

¡It is recommended to set the bit rate to “128 kbps or

more” and “fixed”.

¡Files with copyright protection are not playable.

Compression formats

Compression method

Bit rate

VBR

Yes

Sampling frequency

32, 44.1, 48 kHz

16, 22.05, 24 kHz

12, 11.205, 8 kHz

32, 44.1, 48 kHz

MPEG 1 audio layer 3 (MP3)

MPEG 2 audio layer 3 (MP3)

MPEG 2.5 audio layer 3 (MP3)

32 k – 320 kbps

8 k – 160 kbps

Windows Media Audio Ver. 2, 7, 8, 9* 32 k – 192 kbps

MPEG 4 AAC LC 24 k – 320 kbps

8, 11.205, 12, 16, 22.05,

24, 32, 44.1, 48 kHz

* WMA 9 Professional/LossLess/Voice are not supported.

Caution

Never put an extension indicating compressed audio (such as “.mp3”, “.wma”, and “.m4a”) to

files other than compressed audio files. This may not only produce noise from the speaker

damage, but also damage your hearing.

¡Name files and folders in accordance with the stan-

dard of each file system. Refer to the instructions of

writing software for details.

¡ASCII character set and special characters in each lan-

guage can be displayed.

Display Information

¡Common

Folder name,

File name

¡WMA

Album name,

Title name/artist name

(WMA tag)

¡MP3

ASCII character set

A to Z, a to z, digits 0 to 9, and the following sym-

bols:

(space) ! ” # $ % & ’ ( ) * + , - . / : ; < = > ? @ [ \ ] ˆ

_ ` { | } ~

Album name,

Title name/artist name

(ID3 tag)

¡AAC

Album name,

Title name/artist name

(AAC tag)

Displayable characters

Notes:

¡Displayable length of file name/folder name: within 64

characters. (Unicoded file and folder names are

reduced by half in the number of displayable charac-

ters.)

¡Characters may be garbled depending on encoding

software to be used

¡Undisplayable characters and symbols will be convert-

ed into an asterisk ( ).

CQ-C800U

Compressed audio file writing

Folder selection order/file playback order

Maximum number of files/folders

¡Maximum number of files: 511 (files + folders)

¡Maximum number of files in one folder: 255

¡Maximum depth of trees: 8

¡Do not save an audio file (CD-DA file) and a com-

pressed audio file on the same disc. Failure to

observe this may result in difficulty in playing.

¡If compressed audio files formatted with two or

more types are saved on the same disc, each format

shall have a different folder.

¡Maximum number of folders: 255 (Root folder is

included.)

¡Do not write files other than compressed audio files.

¡Playability may depend on the combination of writing

software and disc writer to be used.

¡This unit does not support the play list function.

¡Write files in a disc-at-once manner unless otherwise

needed.

¡You can shorten the duration between data read and

playback by decreasing the quantity of files or folders,

or the depth of the hierarchy.

Root Folder

(Root Directory)

Folder Selection

In the order

–

File Selection

In the order

–

Supported file systems

ISO 9660 Level 1/Level 2/Level 3, Joliet, Romeo

Tree 1

Tree 2

Tree 3

Tree 4

Tree 8

(Max.)

Note: Apple HFS, UDF 1.50, Mix CD and CD Extra are

not supported.

Notes:

¡This unit counts the number of folders irrespective of

the presence or absence of a compressed audio file.

¡If the selected folder does not contain any com-

pressed audio file, the nearest compressed audio file

in the order of playback will play.

¡Playback order of this unit may be different from that

of other compressed audio players even if the same

disc is used

¡“ROOT” appears when displaying the root folder

name.

iTunes is a trademark of Apple Computer, Inc., regis-

tered in the U.S. and other countries/regions.

It is prohibited by copyright laws to copy, distribute and

deliver copyrighted materials such as music without the

approval of copyright holder except enjoying yourself

personally.

Windows Media, and the

Windows logo are trade-

marks or registered

trademarks of Microsoft

Corporation in the United

States and/or other

No warranty

Above description complies with our investigations as of

October 2006. It has no warranty for reproducibility and

displayability of MP3/WMA/AAC.

countries/regions.

MPEG Layer-3 audio coding technology licensed from

Fraunhofer IIS and Thomson.

CQ-C800U

Audio Setting

Adjustment to each speaker and an optional subwoofer

BALANCE

Balance adjustment

(Setting range: L (left)15 to R (right) 15 and Center,

Default: Center)

q : Right enhanced

Press [PUSH

SEL: Select] to

display the

AUDIO menu

display.

w : Left enhanced

For using the remote control, use [SEL] (MENU).

Press [PUSH SEL: Select] to select a

mode to be

adjusted.

FADER

Fader adjustment

(Setting range: R (rear) 15 to F (front) 15 and Center,

Default: Center)

q : Front enhanced

For using the remote

control, use [SEL]

(MENU).

w : Rear enhanced

Turn [VOL]

clockwise or counterclockwise to adjust. SUB.W

For using the remote control, use [VOL }] or

Subwoofer level adjustment

[VOL {].

(Setting range : mute ( ∞), -6 dB to +6 dB, 2 dB Step,

Default: 0 dB

q : Up

)

Note: Only the VOLUME, SUB.W, LPF, and REAR are

adjustable when SRS WOW is enabled. (apage 18)

w : Down

LPF

VOLUME

Main volume adjustment

(Setting range: 0 to 40, Default: 18)

q : Up

Subwoofer Low Pass Filter

(Setting range: 80 Hz, 120 Hz, 160 Hz, Default: 80 Hz)

q : Up

w : Down

Subwoofer output range

Other speakers output ranges

BASS

Bass adjustment

HPF

High Pass Filter

(Setting range: Filter OFF, 90 Hz, 135 Hz, 180 Hz, 225 Hz,

Default: Filter OFF)

(Setting range:

Bass 0 dB)

q : Up

-12 dB to +12 dB, 2 dB Step, Default:

q : Up

w : Down

TREBLE

Treble adjustment

REAR (SRS WOW)

Rear Level Adjustment

(Setting range: 0 to –15, Default: –10)

q : Up

(Setting range:

Treble 0 dB)

-12 dB to +12 dB, 2 dB Step, Default:

q : Up

w : Down

Note: Do not activate SQ and Bass/Treble at same time

to avoid causing sound distortion.

Note: The rear level is adjustable only when SRS WOW

is enabled. (apage 18)

CQ-C800U

Function Setting

Adjustment to display on the FUNCTION menu

MUTE KEY

Setting [MUTE] buttons’ functions

Press [MENU] to display the menu dis-

play.

Volume off (default)

For using the remote

control, hold down

[SEL] (MENU) for 2

sec. or more.

SOURCE

PWR

DIM

: Volume down by 10 steps

TUNE

TRACK

FOLDER/P-SET/DISC

LIST

MUTE

SBC-SW

・

: Volume down by 5 steps

Press []] or [[] to display the FUNC-

SECURITY

Setting the security function (apage 13)

TION menu.

: ON (default)

: OFF

Turn [VOL] to select a function to be

adjusted.

BUILT-IN AMP

You can toggle the integrated amplifier on and off.

: Amplifier on (default)

For using the remote

SOURCE

PWR

control, use [}] or

DIM

: Amplifier off

(when the external amplifier is used)

[{].

TUNE

TRACK

FOLDER/P-SET/DISC

LIST

MUTE

SBC-SW

・

Press [PUSH

SEL] to adjust.

For using the remote control, use [BAND] (SET).

Press [MENU] to close the menu

screen.

lights when disactivated.

For using the remote control, hold down [SEL]

(MENU) for 2 sec. or more.

CQ-C800U

Display Setting

Adjustment to display on the DISPLAY menu

GRAPHIC PATTERN

(Default: All)

Press [MENU] to display the menu

display.

For using the remote

control, hold down

[SEL] (MENU) for 2

sec. or more.

Turn [VOL] to make a selection.

SOURCE

PWR

DIM

All:

Sequential display from pattern A to D.

TUNE

TRACK

FOLDER/P

-SET/DISC

Pattern A-D

MUTE

SBC-SW

・

LIST

Press []] or [[] to display the

DISPLAY menu.

STILL IMAGE PATTERN

(Default: All)

Turn [VOL] to make a selection.

All:

No.1-10

Sequential display from pattern 1 to 10

Turn [VOL] to select a function to be

adjusted.

For using the remote

SOURCE

PWR

control, use [}] or

DIM

[{].

TUNE

TRACK

FOLDER/P-SET/DISC

LIST

MUTE

SBC-SW

・

Press [PUSH

SEL] to adjust.

CLOCK ADJ

Note: Adjust the clock when “ADJUST” appears on the

For using the remote control, use [BAND] (SET).

display.

[[] : Adjusting minutes

[]] : Adjusting hours

q : Forward

Adjust the setting value.

Press [PUSH SEL].

For using the remote control, use [BAND] (SET).

w : Backward

Press [MENU] to close the menu

screen.

For using the remote control, hold down [SEL]

(MENU) for 2 sec. or more.

DEMONSTRATION

Notes:

¡The graphic pattern and still image are changeable.

(apage 31)

¡If corrupted data is selected, “DISPLAY FILE INCOM-

PLETE” appears. (apage 32)

Switching by [PUSH SEL].

ON:

Demonstration screen at no operation

(default)

OFF:

Regular screen

CQ-C800U

Customize the Display (Customize Function)

You can edit the moving images and still images that are initially stored in the unit. You also can use the data that is downloaded from

the Panasonic Web site and the data that is stored with a digital camera or other devices and processed with exclusive software,

IMAGE STUDIO. See “Notes on Customize function” (apage 32) as well.

Note: Visit Panasonic Web site (http://panasonic.co.jp/pas/en/software/customize/index.html) for details.

Preparation:

Select a file.

Put the CD-R/RW that contains data to

be customized in hand.

If there is a disc inside, take out the

disc.

q w []][[]: Select

Press [SOURCE]

(PWR) to select

the CD mode.

[PUSH SEL]:Confirm

SOURCE

PWR

DIM

Notes:

TUNE

TRACK

FOLDER/P-SET/DISC

LIST

¡Files are automatically identified by their exten-

sions, and target files are displayed.

¡If “BACK” is selected, the screen of step 5

appears.

MUTE

SBC-SW

・

Hold down [PUSH SEL] for 4 sec. or

more to display the menu screen.

For a moving image file or still image

file, select where to save the file.

Load a CD-R/RW that contains data.

Notes:

q w [}][{]: Select

¡It may take time for the unit to identify the CD-

[PUSH SEL]:Confirm

R/RW.

Notes:

¡Discs recorded by the packet writing software are

¡New data overwrites existing data.

¡If “BACK” is selected, the screen of step 6

appears.

not supported.

Select an item to be customized.

Confirm the changed item.

q w :

Select

[PUSH SEL]: Confirm

q w :

[PUSH SEL]: Confirm

Select

Note: To exit the customize menu, hold down

[PUSH SEL] for 4 sec. or more.

GRAPHIC PATTERN

Moving image (graphic pattern) data (apage 30)

Customization is performed. Do not turn off the

power in mid-operation. (It takes approx. 5 minutes

to complete this operation for a 548 kB moving

image.) After completion of this operation, the

screen of step 5 appears.

STILL IMAGE

Still image data (apage 30)

Note: If “NO” is selected, the screen of step 5

appears.

OPENING MESSAGE

Moving image at power on

Press [uOPEN] to eject the disc.

CLOSING MESSAGE

Moving image at power off

Hold down [PUSH SEL] for 4 sec. or

more.

The CD mode comes back.

CQ-C800U

Customize the Display (Customize Function) (continued)

Note on Download Service

At Customizing

The download service may be suspended or stopped

without advance notice. The download service is not

available in some areas. Please visit the site below for

further information.

¡If customizing is interrupted on account of turning off

the power, stopping the engine, removing the face

plate or other reasons, you may lose the data. In such

a case, try customizing again.

¡The default image exists on the Panasonic Web site. If

you would like to restore it, download the image from

the site.

Panasonic Web site:

(http://panasonic.net)

Download site:

http://panasonic.co.jp/pas/en/software/

customize/index.html

Notes on IMAGE STUDIO

¡This download service is not available in some areas.

For details, please access the Panasonic website.

¡IMAGE STUDIO is available only by downloading from

the address below. It is not bundled with this unit.

¡Refer to the downloaded operating manual for how to

use IMAGE STUDIO.

Error Display Messages

NO FILES DETECTED

No customize-specific data on the disc

a Load a disc that contains customize-specific

Notes on File

data.

¡The customize-specific file is downloadable from the

URL below. You can create exclusive files stored with

a digital camera or other devices by using exclusive

software, IMAGE STUDIO that can be accessed from

the same URL.

CUSTOMIZING FAILED

Customize failed

a Check to see whether or not the extension is cor-

rect and file contents are appropriate.

¡Do not change the extension. Otherwise, the data can-

not be recognized.

DISPLAY FILE INCOMPLETE

At Disc Making

¡Save only customize-specific data.

¡Save all data in the root directory. Files contained in a

folder cannot be recognized.

Intended moving image or still image is damaged.

a Customize it again and overwrite the file with

new one.

¡Follow the table below with regard to the number of

files that are saved to a disc. Files beyond the speci-

fied capacity are not readable.

¡ Discs recorded by the packet writing software are not

supported.

Type

Extension

.pfm

Max. number

GRAPHIC PATTERN

STILL IMAGE

.pfs

OPENING MESSAGE

CLOSING MESSAGE

.pfo

.pfe

CQ-C800U

Troubleshooting

If You Suspect Something Wrong

Check and take steps as described below.

Warning

If the described suggestions do not solve the problem, it is

recommended to take the unit to your nearest authorized Panasonic

Servicenter. The product should be serviced only by qualified personnel.

Please refer the checking and the repair to professionals. Panasonic

shall not be liable for any accidents arising out of neglect of checking the

unit or your own repair after your checking.

Never take measures especially for those other than indicated by ital-

ic letters in “Possible Solution” described below because those are

too dangerous for users to handle themselves.

¡Do not use the unit in an irregular condition, for

example, without sound, or with smoke or a foul

smell, which can cause ignition or electric shock.

Immediately stop using the unit and consult your

dealer.

¡Never try to repair the unit by yourself because it is

dangerous to do so.

Possible cause

Possible solution

Problem

The power cord (battery, power and ground) is connected in the wrong way.

a Check the wiring.

No power to the

unit

Fuse blows out.

a Eliminate the cause of fuse blowout and replace the fuse with new one.

Consult your dealer.

MUTE is set to ON.

a Set MUTE to OFF.

Sound is not

generated.

The wiring of speaker lines are not correct, or a break or poor contact arises.

a Check the wiring in accordance with the wiring diagram. (Installation

Instructions)

There is an electromagnetic-wave generator such as a cellular phone near the unit or

its electrical lines.

a Keep an electromagnetic-wave generator such as a cellular phone away from

the unit and the wiring of the unit. In case that noise cannot be eliminated

due to the wiring harness of the car, consult your dealer.

Noise

The contact of the ground lead is poor.

a Make sure that the ground lead is connected to an unpainted part of the chas-

sis securely.

Noise is made in

step with engine

revolutions.

Alternator noise comes from the car.

a Change the wiring position of the ground lead.

a Mount a noise filter on the power supply.

CQ-C800U

Troubleshooting (continued)

Possible cause

Possible solution

Problem

Some operations are not executable in particular modes such as menu mode.

a Read the operating instructions carefully and cancel the mode. If the unit is

Some operations

are not executable.

still out of order, consult your dealer.

BALANCE/FADER setting is not appropriate.

a Readjust BALANCE/FADER.

No sound from

speaker(s)

There is a break, a short circuit, poor contact or wrong wiring regarding the speaker

wiring.

a Check the speaker wiring.

The speaker

channels are

reversed between

right and left.

The speaker wiring is confused between right and left.

a Perform the speaker wiring in accordance with the wiring diagram.

The sound field is

not clear in the

stereo mode.

Central sound does

not settled.

The plus and minus terminals at right and left channels of speakers are connected

reversely.

a Perform the speaker wiring in accordance with the wiring diagram.

The safety device works.

a Consult your dealer, or your nearest Panasonic Servicenter.

The power fails

unintentionally.

Antenna installation or wiring of antenna cable is faulty.

a Check whether the antenna mounting position and its wiring are correct. In

addition, check to see whether the antenna ground is securely connected to

the chassis.

Poor reception or

noise

No power is supplied to the antenna amplifier (when using a film antenna, etc.).

a Check the wiring of the antenna battery lead.

The number of auto

preset stations is

less than 6.

The number of receivable stations is less than 6.

a Move to an area where receivable stations number is maximum, and try pre-

setting.

The contact of the battery lead is poor, or the battery lead is not always powered.

a Make sure that the battery lead is connected securely, and preset stations

Preset stations

cannot be stored.

again.

CQ-C800U

Possible cause

Possible solution

Problem

The disc is inserted upside down.

a Insert a disc correctly.

No playback or

disc ejected

There is a flaw or foreign material on the disc.

a Remove the foreign material, or use a flawless disc.

There is a flaw or foreign material on the disc.

a Remove the foreign material, or use a flawless disc.

Sound skipping or

noise

The unit is not sufficiently secured.

a Secure the unit to the console box.

Sound skipping

due to vibration

The unit is tilted at over 30˚ in the front-to-end direction.

a Make the angle 30˚ or less.

Something such as a peeled label obstructs the disc coming out.

a Press and hold the [uOPEN] for more than 2 seconds when the face plate is

open (disc forced ejection). In case that the disc forced ejection does not

work, consult your dealer.

Disc unejectable

The microcontroller in the unit operates abnormally due to noise or other factors.

a Unplug the power cord and plug it again. In case the unit is still out of order,

consult your dealer.

The disc has unplayable formatted data.

a Check the file format.

No playback or

disc ejected

The CD-R/RWs that

are playable on

other devices are

not playable on

this unit.

The playability of some CD-R/RWs may depend on the combination of media,

recording software and recorder to be used even if these CD-R/RWs are playable on

other devices such as a PC.

a Make CD-R/RWs in different combination of media, recording software and

recorder after referring to the description about the compressed audio player.

There is a flaw or foreign material on the disc.

a Remove the foreign material, or use a flawless disc.

Sound skipping or

noise

Playing VBR (Variable Bit Rate) files may cause sound skipping.

a Play Non-VBR files.

Noise is heard with

“RE-MASTER” at

“ON”

With some CDs, noise may be heard in the treble range when playing compressed

audio files into which the CD tracks were encoded with “RE-MASTER” enabled.

a If noise is heard, set “RE-MASTER” to “OFF”.

CQ-C800U

Troubleshooting (continued)

Possible cause

Possible solution

Problem

The battery is inserted in the wrong direction. A wrong battery is inserted.

aInsert a correct battery in the correct direction.

The battery is weak.

aReplace the battery with new one.

No response to

pressing buttons

The aiming direction of the remote control unit is wrong.

aAim the remote control unit at the sensor of the unit and press buttons.

The sensor is exposed to direct sunlight. (The remote control unit may not be opera-

ble when the sensor is exposed to direct sunlight. In such a case, the system is not

faulty.)

aBlock off sunlight to the sensor.

CQ-C800U

Error Display Messages

Possible cause

Possible solution

Display

The disc is dirty, or is upside down.

aCheck the disc.

The disc has scratches.

aCheck the disc.

No operation by some cause.

aUnplug the power cord and plug it again. In case the unit is still out of order,

consult your dealer. (aInstallation Instructions)

The player for some reason cannot read the file you are trying to play. (File recorded

in an unsupported file system, compression scheme, data format, file name exten-

sion, damaged data, etc.)

a Select a file that the player can read. Check the type of data recorded on the

disc. Create a new disc if necessary.

A WMA file can be copyrighted.

(After 5 seconds)

aThe file protected by copyright is not playable.

To next file automatically

No disc.

Note: Refer to the System Upgrade Guidebook for error messages regarding optional products.

CQ-C800U

Notes on Discs

If you use commercial CDs, they must have

either of these labels shown at right.

Some copy-protected music CDs are not

playable.

TEXT

How to hold the disc

¡Do not touch the underside of the disc.

¡Do not scratch on the disc.

Printed side

¡Do not bend the disc.

¡When not in use, keep the disc in a case.

Do not leave discs in the following places:

¡In direct sunlight

¡Near car heaters

¡Dirty, dusty and damp areas

¡On seats and dashboards

Labels created by a printer, Irregularly shaped discs

Protective films or sheets

Disc cleaning

Use a dry, soft cloth to wipe from the center outward.

<Wrong>

Disc with adhered

stickers or tape

Discs with cracks,

scratches or parts missing

Do not write on the disc label with a ballpoint

pen or other hard-point pens.

¡You may have trouble playing back some CD-R/RW discs recorded on CD recorders (CD-R/RW drives), either due

to their recording characteristics or dirt, fingerprints, scratches, etc. on the disc surface.

¡CD-R/RW discs are less resistant to high temperatures and high humidity than ordinary music CDs. Leaving them

inside a car for extended periods may damage them and make playback impossible.

¡Some CD-R/RWs can not be played back successfully thanks to incompatibility among writing software, a CD

recorder (CD-R/RW drive) and the discs.

¡This player cannot play the CD-R/RW discs if the session is not closed.

¡This player cannot play the CD-R/RW discs which contains other than CD-DA or compressed audio data.

¡Be sure to observe the instructions of CD-R/RW disc for handling it.

Maintenance/Fuse

Your product is designed and manufactured to ensure the minimum of maintenance. Use a soft cloth for

routine exterior cleaning. Never use benzine, thinner, or other solvents.

If the fuse blows out, consult your dealer, or your nearest authorized Panasonic Servicenter.

Warning

¡Use fuses of the same specified rating (15 A). Using substitutes or fuses with higher ratings, or connecting the

unit directly without a fuse could cause fire or damage to the unit. If the replaced fuse fails, contact your

nearest authorized Panasonic Servicenter.

CQ-C800U

Specifications

Power Supply

DC 12 V (11 V – 16 V), Test Voltage 14.4 V, Negative Ground

Tone Controls (Bass/Treble)

Equalizer Center Frequency

Variable Range of Equalizer

Current Consumption

Bass; 12 dB at 60 Hz, Treble; 12 dB at 16 kHz

60, 160, 400, 1 k, 3 k, 6 k, 16 k Hz

-12 dB to 12 dB (2 dB step)

Less than 2.2 A (CD mode, 0.5 W 4-Speaker)

Maximum Power Output 50 W x 4 (at 1 kHz)

Speaker Impedance

Pre-amp output voltage

Subwoofer-output voltage

4 – 8 Ω

5 V, (CD mode, 1 kHz, 0 dB)

Pre-amp output impedance 60 Ω

Subwoofer-output impedance

Dimensions (Main Unit) 178(W) x 50(H) x 155(D) mm {7” x 1 /¹⁶”x 6 /⁸”}

60 Ω

Weight (Main Unit)

1.6 kg {3 lbs. 8 oz}

Sampling Frequency

DA Converter

Pick-Up Type

Light Source

Wavelength

8 times oversampling

4 DAC System

Astigma 3-beam

Semiconductor laser

790 nm

Frequency Response

Signal to Noise Ratio

Total Harmonic Distortion

Wow and Flutter

Channel Separation

20 Hz – 20 kHz ( 1 dB)

96 dB

0.01 % (1 kHz)

Below measurable limits

85 dB

Frequency Range

Usable Sensitivity

50 dB quieting Sensitivity

Frequency Response

87.9 MHz – 107.9 MHz

10.2 dBf (0.9 µV, 75 Ω)

15.2 dBf (1.6 µV, 75 Ω)

30 Hz – 15 kHz ( 3 dB)

Alternate channel selectivity 75 dB

Stereo Separation

Image response ratio

IF response ratio

30 dB (at 1 kHz)

55 dB

100 dB

62 dB

Signal to noise ratio

Frequency Range

Usable Sensitivity

530 kHz – 1 710 kHz

27 dB/µV (S/N 20 dB)

Above Specifications comply with EIA standards.

Power Output:

18 W RMS x 4 Channels at 4 Ω and ≤ 1%

THD+N

Signal to Noise Ratio:

85 dBA (reference: 1 W into 4 Ω)

Notes:

¡Specifications and design are subject to modification

without notice due to improvements.

¡Some figures and illustrations in this manual may be

different from your product.

CQ-C800U

Plantronics Bluetooth Headset 815 User Manual
Pioneer Premier DEH P700BT User Manual
Panasonic NV DS60A User Manual
Olympus E PM1 User Manual
Marshall electronic M LCD7 HDMI B NEL3 User Manual
Manfrotto MBAG80 User Manual
KitchenAid KCB348 User Manual
Kicker DS400 User Manual
Kenwood Car Stereo System KDC 3090RA User Manual
JVC GZ HD300U User Manual