Panasonic AW AD700BS User Manual

Cam era Adaptor  
AW-AD700BS  
for AW-F575 Series  
Before attempting to connect or operate this product, please read  
these instructions completely.  
PREFACE  
• The Camera Adaptor AW-AD700BS docks directly  
to the Color Camera AW-F575 series, making it a  
standard-alone camera for two-piece recording  
system applications.  
• Video Power (VP) Multiplex Operation is available  
using with the Power Separator WV-PS700.  
• Possible to mount a lens having zoom, focus or  
servo functions.  
Connection via a VTR cable for several different  
portable recorder is possible.  
• Pan/Tilt Control function is provided.  
NOTE: Refer to the operating instructions of Color Camera AW-F575 series for details.  
For U.S.A  
Warning:  
CAUTION  
This equipment generates and uses radio frequency  
energy and if not installed and used properly, i.e., in  
strict accordance with the instruction manual, may  
cause harmful interference to radio communications.  
It has been tested and found to comply with the limits  
for a Class A computing device pursuant to Subpart J of  
Part 15 of FCC Rules, which are designed to provide  
reasonable protection against such interference when  
operated in a commercial environment.  
RISK OF ELECTRIC SHOCK  
DO NOT OPEN  
CAUTION:  
TO REDUCE THE RISK OF ELECTRIC SHOCK,  
DO NOT REMOVE COVER (OR BACK). NO  
USER SERVICEABLE PARTS INSIDE.  
REFER SERVICING TO QUALIFIED SERVICE  
PERSONNEL.  
For CANADA  
This digital apparatus does not exceed the Class A limits  
for radio noise emissions from digital apparatus set out in  
the Radio Interference Regulations of the Canadian  
Department of Communications.  
The lightning flash with arrowhead sym-  
bol, within an equilateral triangle, is  
intended to alert the user to the pres-  
ence of uninsulated "dangerous voltage"  
within the product's enclosure that may  
be of sufficient magnitude to constitute a  
The serial number of this product may be found on the  
bottom of the unit.  
You should note the serial number of this unit in the  
space provided and retain this book as a permanent  
record of your purchase to aid identification in the event  
of theft.  
SA 1965  
risk of electric shock to persons.  
The exclamation point within an equilat-  
eral triangle is intended to alert the user  
to the presence of important operating  
and maintenance (servicing) instructions  
in the literature accompanying the appli-  
ance.  
Model No.  
Serial No.  
SA 1966  
WARNING:  
TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.  
R/G/B:  
The R, G and B signals are supplied from the  
R, G and B Output Connector.  
Y/PR/PB:  
14. Gen-lock input connector (BNC) (GEN-LOCK)  
The color video signal of the camera is automatical-  
ly synchronized to the Gen-lock signal (composite  
or black burst) which is supplied to this connector.  
The gen-lock signal is used for system reference,  
such as when using a Special Effects Generator.  
Caution:  
The color difference (R-Y & B-Y) signals and  
luminance (Y) signal are supplied from the  
VTR/RCU Connector (18) and the R, G and B  
Output Connectors on the Remote Control Unit  
for MII and Betacam format VTRs.  
If the gen-lock signal is jittery (such as when  
obtained from VTR playback), the camera may  
not be able to synchronize properly.  
9. VTR Compatibility Switch (!1/!2/@1)  
Set this switch according to the VTR which is con-  
nected to the camera.  
15. Multiplex Signal input Connector (MPX)  
Communications between the camera side and the  
Remote Control Unit (RCU) are available through a  
single coaxial cable by using this connector as the  
composite signal, gen-lock signal, control signal  
and intercom/audio signal are multiplexed, and the  
composite signal is output from the Remote control  
Unit (RCU).  
!1: For 1/2” VHS VTRs.  
!2: For 3/4” U-vision VTRs, connected to the cam-  
era using a 14-pin connector, S-VHS VTRs and  
MII portable VTRs.  
@1: If a VTR of other manufacture is used, and if  
this VTR pauses when the tape should be run-  
ning and vice versa, this switch should be set  
to this position.  
16. External DC Input Connector (XLR, 4-pin) (EXT  
DC)  
Notes:  
1) The switch has been preset to the !1 position  
at the factory.  
2) Some VTRs may not operate properly when  
connected to this camera, even though the set-  
ting of this switch is changed. Please consult  
your dealer for further information.  
This connector accepts the power cable from an  
external DC source supplying nominal power of  
12 V, 2 A (a belt type battery or car battery for  
example). This connector also accepts the power  
cable from an AC adaptor. For powering the studio  
configuration, a 12 V DC, 2.5 A power source is  
required.  
10. Earphone Out Selection Switch (INT/PB)  
Cautions:  
This switch selects the audio signal from the  
Earphone Jack (7) to be monitored.  
INT:  
Use only with a 12V DC power source with a  
Class 2 rating. Do not use with an external stor-  
age battery unless provided with an 8A rated  
fuse, located within 5 inches of the battery con-  
necting means.  
The sound picked up by the microphone can  
be monitored.  
PB:  
An eternal DC source supplied to this connec-  
tor gets the highest priority, i.e., it is selected  
before the battery connector or Multicore/  
VTR/DC source.  
The played back audio can be monitored.  
Note:  
The camera has been preset to the INT posi-  
tion at the factory.  
17. Circuit Protector (BREAKER)  
When excessive current flows into the camera due  
to some fault, the red button of this circuit protector  
protrudes to cut off the circuit power. After solving  
the problem, press the red button again to reset the  
circuit protector.  
11. Audio Level Selection Switch  
(AUDIO LEVEL –20/–60 dB)  
Two audio output levels to the VTR can be select-  
ed: –20 dB or –60 dB  
The camera has been preset to –20 dB at the facto-  
ry.  
Caution:  
When using this adaptor with WV-RC700A, set this  
switch to the –20 dB position.  
Refer servicing to qualified service personnel  
to solve the problem.  
12. Cable Selection Switch (VTR MULTI/MPX)  
This switch is used to select either the multi-cable  
VTR/RCU cable or the single coaxial multiplex  
cable. When using the multi-cable in the VTR or  
Remote Control Unit (RCU), set this switch to VTR  
MULTI position. In case of the multiplex or VP multi-  
plex operation using a coaxial cable, set this switch  
to MPX position.  
18. VTR/RCU Connector (26-pin) (VTR/RCU)  
When using the camera together with a Panasonic  
portable color VTR, the specified VTR Cable should  
be connected between the camera and VTR. This  
connector is also used for connection with the 26-  
pin studio cable from the Remote Control Unit  
(RCU) for comprehensive system operation. When  
connecting the 26-pin studio cable to this connec-  
tor, the camera is automatically set to the Remote  
Control Unit (RCU) operation mode.  
Note:  
Video Power (VP) Multiplex system: multiplex  
signal and power are supplied using a single  
coaxial cable.  
• 1/2” VHS and 3/4” U-vision portable VTR (10-  
pin)  
WV-CA26A10 (26p-10p cable)  
13. Video Output Connector (BNC) (VIDEO OUT)  
A composite video signal is provided at this con-  
nector.  
3/4” U-vision portable VTR (14-pin)  
WV-CA26A14 (26p-14p cable)  
-3-  
MII portable VTR (26-pin)  
WV-CA26A26 (26p-26p cable)  
• 26-pin Studio Cable (RCU Cable)  
WV-CA26U15  
22. Recording/Tally Indicator (red) (REC TALLY)  
This indicator lights when the VTR is set to the  
recording mode (through the VTR Start/Stop  
Button), and informs the person concerned of  
scenes being recorded. The Tally indicator also  
lights when the camera is in full system operation  
together with the Remote Control Unit and Special  
Effects Generator. In case a tape is not loaded or  
the tape end is reached, or if the servo mechanism  
is working improperly, this indicator will start blink-  
ing to warn the operator of such faults.  
WV-CA26U30  
WV-CA26U100  
19. Lens Connector  
This connector is used to connect the lens cable  
for zoom, focus or servo control.  
20. Control Connector  
Note:  
This connector is used to connect the optional  
Pan/Tilt Control Cable WV-CA10U25.  
If a portable VTR is not connected to the cam-  
era, the Recording/Tally Indicator will not light.  
21. Battery Connector (BATTERY)  
23. Battery Pack Mounting Angle  
Connect the cord from the Battery Pack to this con-  
Mount the Battery Pack WV-PS60/WV-PS33, the AC  
Adaptor/Charger WV-PS34 or Power Separator WV-  
PS700 on the camera by sliding it down along this  
mounting angle.  
nector.  
+
24. 68-pin Multi Connector  
When mounting this adaptor, engage the 68-pin  
connectors on the camera and this connector.  
Connector information  
VTR/RCU Connector (18)  
• Pin configuration  
<Front View>  
Pin No.  
Pin No.  
12  
A
B
1
12V IN  
VTR TRIGGER  
VIDEO IN/OUT  
INTERCOM MIC  
TALLY WARNING  
INTERCOM SPEAKER  
GND  
GND  
13  
ENC (NTSC OUT)  
GND  
14  
2
15  
3
Not used  
16  
4
ENC/G/Y/Y  
R/PR (R-Y)/CHROMA  
SENSING GND  
B/PB (B-Y)/B  
GND  
17  
5
18  
PLAYBACK VIDEO  
GND  
6
19  
7
20  
PLAYBACK AUDIO  
TRANSMIT/RECEIVE  
BATTERY ALARM  
GEN-LOCK IN  
+12V RETURN  
8
21  
9
AUDIO+  
22  
10  
11  
AUDIO–  
23  
AUDIO GND  
24  
-4-  
• Control Voltage (each voltage is ±0.5V.) for the  
lens.  
Lens Connector (19)  
• EPin configuration  
1
2
Not used  
Not used  
GND  
Speed  
3
Low  
4.0V  
6.0V  
4.0V  
6.0V  
High  
2.5V  
7.5V  
2.5V  
7.5V  
4
Not used  
Not used  
+12V IN  
NEAR  
FAR  
5
6
WIDE  
TELE  
7
+5V IN  
8
FOCUS CONT  
ZOOM CONT  
Not used  
+7.5V IN  
+2.5V IN  
<Front View>  
9
10  
11  
12  
Pan/Tilt Control Connector (20)  
Optional Pan/Tilt Control Cable  
• Pin configuration  
WV-CA10U25  
1
2
GND  
Red  
COM (0V)  
Not used  
LEFT  
Brown  
3
4
5
RIGTH  
Glay  
6
UP  
Purple  
7
DOWN  
Blie  
8
DEFROSTER  
WIPER  
<Front View>  
9
10  
Not used  
Green  
Yellow  
White  
Note:  
Be sure to follow the conditions indicated below.  
1. Functions are active at the Low control voltage.  
2. Open Collector Output (Withstand voltage of  
Transistor is maximum 30 V.)  
3. Current is maximum 20 mA.  
Audio System Operation with the optional Remote Control Unit  
The audio output to the Remote Control Unit WV-RC700A is available in the VP Multiplex operation.  
1. Connect a coaxial cable between the Remote Control Unit WV-RC700A and Power Separator WV-PS700.  
2. Connect the Multiplex Output Cable on WV-PS700 to the Multiplex Signal Input Connector (15) on this adaptor.  
3. Set the Audio Level Selection Switch (11) to the –20 dB position.  
4. Remove four screws from the side cover of this adaptor.  
5. Set the Switch 1 on the Audio board inside this adaptor to the AUDIO position.  
6. Set the Switch 2 on the MOD board inside the Remote Control Unit WV-RC700A to the AUDIO position.  
SW1  
(Set this switch to  
AUDIO position.)  
INCOM  
AUDIO  
Remove four Screws.  
Notes:  
1. At this time, the intercommunication system cannot function.  
2. The Switch 1 on the Audio board is preset to the INCOM position at the factory.  
-5-  
INSTALLATION  
Installation of the Camera Adaptor  
1. Mounting the Camera Adaptor  
2. Removing the Camera Adaptor  
1-1 Mount the Camera Adaptor with Camera Handle to  
the camera while engaging the 68-pin connector.  
2-1 Loosen two Camera Adaptor Holding Screw/Knob  
(2) on the Camera Adaptor.  
Loosen two Camera Adaptor  
Holding Knobs.  
68-pin connector.  
1-2 Tighten two Camera Adaptor Holding Screw/knob  
(2) firmly and make sure the adopter is securely  
fixed to the camera.  
2-2 Remove the Camera Adaptor while pressing up the  
Release Button underneath the camera.  
Tighten two Camera Adaptor  
Holding Knobs.  
Release  
Button.  
CAUTION:  
Mount the Camera Adaptor by sliding it straight  
and engaging the connectors and lock mechanism  
in order not to bend the pins of the connector and  
not to make a short circuit.  
-6-  
SPECIFICATIONS  
Camera Docked:  
Gen-lock Input:  
Video Output:  
Color camera AW-F575 series connected through 68-pin connector  
NTSC composite (VBS) signal or black burst signal  
1.0 V[p-p] NTSC composite/75 (BNC) connector  
Y/C (S-VIDEO) Output: (S-VIDEO Connector)  
0.714 V[p-p] Video Level Luminance (Y) composite/75 Ω  
0.286 V[p-p] Burst Level Chrominance/75 Ω  
VTR/RCU Output (26-pin connector)  
1.0 V[p-p] NTSC Composite/75 Ω  
Composite, Y/C/B, R/G/B, Y/PR/PB Selectabe  
Composite:  
R/G/B:  
Y/PR/PB:  
1.0 V[p-p] composite/75 Ω  
0.714 V[p-p]/75 x 1 each  
Y: 1.0 V[p-p] (Sync 0.3 V)/75 Ω  
PR/PB: 0.486 V[p-p] (SMPTE Color  
bar)/75 Ω  
Y: 0.714 V[p-p] Video Level  
Luminance (Y) composite/75 Ω  
Y/C/B:  
C: 0.286 V[p-p] Burst Level Chrominance/75 Ω  
B: 0.7 V[p-p]/75 Ω  
1.0 V[p-p] composite/75 through 26-pin VTR/RCU connector  
–20 dBm or –60 dBm/unbalanced, switchable (26-pin VTR/RCU  
Connector)  
Auxiliary Input:  
Audio Output:  
MPX Input/Output:  
Frequency Multiplex Signal  
(Composite Video, Gen-lock Video, Remote Control Signal,  
Intercom/Audio)/75 , N connector  
Zoom, Focus, Servo  
Lens Output:  
Control Output:  
Switches:  
Open Collector  
Audio Level Selection, Earphone Out Selection, RCU/VTR Signal  
Selection, Cable Selection, VTR Compatibility  
Earphone/Intercom Level  
Controls:  
Power Source:  
12 V DC, 6 sources as follows:  
(1) Battery Pack (2) AC Adaptor  
(3) External DC source through 4-pin DC connector  
(4) VTR (external AC adaptor)  
(5) Remote Control Unit through VTR/RCU connector  
(6) VP Multiplex from RCU  
Ambient Operating Temperature:  
Ambient Operating Humidity:  
–10°C - +45°C (14°F - +113°F)  
30% - 90%  
Dimensions (without the Camera Handle):  
125 (W) x 233 (H) x 299 (D) mm  
4-7/8”(W) x 9-3/6” (H) x 11-3/4”(D)  
1.8 kg (4.0 lbs.)  
Weight (exclude the Camera Handle):  
Dimensions and weights are approximate.  
Specifications are subject to change without notice.  
OPTIONAL ACCESSORY  
Pan/Tilt Control Cable ................. WV-CA10U25 (25m)  
-7-  
Broadcast & Television Systems Company  
Division of Matsushita Electric Corporation of America  
Executive Office: One Panasonic Way 3F-5, Secaucus, NJ 07094  
Regional Offices:  
EASTERN ZONE: 50 Meadowlands Parkway, Secaucus, NJ 07094 (201) 348-7620  
CENTRAL ZONE: 1707 North Randall Road, Elgin, IL 60123 (847) 468-5200  
SOUTHERN ZONE:  
Atlanta Region: 1225 Northbrook Parkway, Suite 1-160, Suwanee, GA 30024  
Panazip 11 (770) 338-6841, fax (770) 338-6741  
Law Enforcement Video Products: 1225 Northbrook Parkway, Suite 1-160, Suwanee,  
GA 30024, Panazip 11 (770) 338-6844, fax (770) 338-6721  
WESTERN ZONE:  
Seattle Region: 1200 Westlake Ave., North, Suite 508, Seattle, WA98109 (206) 285-8883  
Los Angeles Region: 6550 Katella Ave. 17A-1, Cypress, CA 90630 (714) 373-7271  
Government Marketing Department: 52 West Gude Drive, Rockville, MD 20850 (301) 738-3840  
PANASONIC CANADA INC.  
5770 Ambler Drive, Mississauga, Ontario, L4W 2T3 Canada (905) 624-5010  
PANASONIC SALES COMPANY  
DIVISION OF MATSUSHITA ELECTRIC OF PUERTO RICO, INC.  
San Gabriel Industrial Park, 65th Infantry Ave. KM. 9.5 Carolina, Puerto Rico 00630 (809) 750-4300  
NM0998-0  
7J1A227A  
Printed in Japan  
N 13  

Panasonic Cordless Phone With Answering Machine KX TG7643 User Manual
Panasonic Camcorder AG AF100P User Manual
Motorola Tx500 Wireless Bluetooth Car Hands Free Kit 89494N User Manual
Marvel Industries 61WCM User Manual
Lochinvar 45 User Manual
Leupold VX II User Manual
KitchenAid KFP715OB2 User Manual
Kicker SOLOCLASSIC S12C User Manual
Kicker Car Amplifier KX24001 User Manual
Kenwood Car Stereo System KDC 148 User Manual