CELLAR
nuvo
2 5 0 / 5 0 0
TM
ko o l s pac e
ASSEMBLY & OPERATION MANUAL
HARDWARE KIT
A
B
C
D
Cam Cap
x 26 (x30)*
Hex bolt
x 22 (x30)*
Coupler screw
x 8
Hex wrench
x 1
E
F
G
H
Cam
x 24 (x28)*
Cam Pin
x 24 (x28)*
Coupler hanger
x 4
Hinge
x 4
I
J
In Cooling Unit Box
Hex Bolt (Flange)
x 2
Panel Insulation Strip
*NOTE : Hardware quantities for Model 500 are indicated in parenthesis.
~3~
STEP 1 : PANEL PREPARATION
CAUTION :
J
1. Watch for sharp staples on boxes.
2. DO NOT STEP ON PANELS
3. The manual will give a recommended
PANEL EDGE
order to open boxes, it saves time and space.
J
J
Open Boxes VP6 and VP7.
J
Install INSULATION STRIP (J) to
Back, Top, and Bottom Panels. PUSH
IN FULLY!
1
2
Insert Cam Pins (F) in BACK PANEL’S
predrilled holes down to TAB. (May
require some force)
CAUTION : DO NOT BREAK CAM PIN TABS!
DO NOT HAMMER!
!
TAB
TAB
BACK PANEL
F
C
3
Screw
in
both
3
screws (C) half
way in Coupler
Hanger (G) to back
panels and tighten
fully when both
screws are in.
G
~4~
STEP 2 : CABINET ASSEMBLY
MET
AL
2
PANEL EDGE
CAM in LOCKED
POSITION
MET
AL
Use allen key provided or
#3 phillips screwdriver.
BOTT
OM P
ANEL
1
2
Attach TOP and Bottom to
Back by CAREFULLY aligning
edge holes over Cam Pins
and gently push together to
avoid damaging cam pins. DO
NOT BANG OR SLAP PANELS
TOGETHER!!!
����
Insert Cam, push all the way
in under panel level (may
require some force) and
make sure Arrow points to
outside edge.
Insert Center COUPLER
BAR by guiding edge
holes over bottom
Cam Pins. Lightly push
out top panel edge to
allow Cam Pins to go in
Coupler Bar. Insert and
tighten Cams.
Gently push down to bring
panels together before you
tighten the Cam. Start with
cams at each end.
3
Cam Arrow faces away from
outside edge when tightened.
BOTT
OM P
ANEL
3
COUPLER BAR
INSIDE
CABINET
~5~
STEP 2 : CABINET ASSEMBLY CONTINUED
Open Box VP5 or VP2.
Insert Cam Pins (F) in BACK PANEL’S predrilled holes down
to TAB. (May require some force)
1
2
Attach SIDES to Back/Bottom/Top by CAREFULLY aligning
edge holes over Cam Pins and gently push together to
avoid damaging cam pins. DO NOT BANG OR SLAP PANELS
TOGETHER!!!
Insert Cam, push all the way in under panel level (may
require some force) and make sure Arrow points to outside
edge., Push Panels together before tightening Cam, use allen
key provided or #3 phillips screwdriver. Start with cams at
TOP !!!
2 HOLES FOR MODEL 250
F
3 HOLES FOR MODEL 500
BOTT
OM P
ANEL
3
A
�
�
�
�
Insert Cam Cap (A) in
all Cam Holes.
3
~6~
STEP 3 : HINGE,BASE AND LEGS INSTALLATION
Open Box VP3.
2
Fasten one HINGE (found in
door box) to the SIDE of the
cabinet
1
H
Install four LEGS (H) into
BASES fully in.
2
3
Fasten FRONT BASE
to
the BOTTOM of the cabinet
(FRONT BASE has to be set
with end tabs away from front
edge)
H
Fasten BASE with HEX BOLTS
(B)
4
H
1
4
BOTT
OM OF CABINET
B
3
D
1
5
NOTE: Fasten base with base tab away from the
front edge, then fasten and adjust the hinge
before fully tightening HEX BOLTS (B)
Raise cabinet and check for potential air
leaks at panel joints from inside.
5
~7~
STEP 4 : SHELVES
COUPLER SHELVES
1
Install COUPLER SHELVES between
the VERTICAL COUPLER and the
BACK PANEL, hook them on the
COUPLER HANGERS (G)
1
2
G
Install 4 HANGERS STRIPS, hook-
ing them to the COUPLER SHELVES
through square holes. (Watch for
orientation, all hooks have to point
upwards).
NOTE : Assure that each of them is
hooked to all 4 shelves
2
VERTICAL COUPLER
PRESS
TOP
BOTTOM
3
Open box VP4S or VP4D
3
Hook SHELVES into hangers start-
ing from the bottom of cabinet, (12
shelves on cooling unit side, 14 on
the other) alternating the two sides
2
1
HINT :
CENTER SHELVES ON HANGERS
1
2
Snap SHELVES into
hangers on one side
Push the SHELVES
down to snap into op-
posite side hangers
~8~
STEP 5 : COOLING UNIT INSTALLATION
1
GET HELP BEFORE INSTALLING AND KEEP CHILDREN CLEAR OF CELLAR CONSTRUCTION AREA.
Get helper to help guide unit, keep light cord clear of edge inside cellar and to prevent tipping of cellar. MAKE
SURE INSULATION STRIP IS IN CORRECT ORIENTATION. Run light cord through Cut-out. Slide unit into the back
opening by angling unit A to allow light cord to clear and straighten to push in B . Screw allen bolts (I) through
bottom flange holes. Make sure unit is level!
CHECK
KEEP UNIT LEVEL
DO NOT!!!
INSULATION
STRIP
LEVEL TO
OPENING
SHELF
SIDE VIEW
STRAIGHTEN AND
PUSH THROUGH
GET HELPER TO
LIFT UNIT LEVEL
AND PULL FROM
INSIDE
B
A
I
CORD MUST
CLEAR OPENING
(I) x2 Flange
bolts in
cooling unit
box.
DO NOT OVER
TIGHTEN
D
NOTE: If unit is operated according to specifications overflows will not occur. Excess
condensation is only caused by extreme conditions. Unit will shut off at 72 °F and will
restart when temperature drops or unit is repluged. (In this case insert 3/8” O.D. hose
to drain hole, cut to appropriate length.)
Optional (not required)
except as emergency
drain.
Container
~9~
STEP 6 : LIGHT AND LIGHT COVER INSTALLATION
1
2
Plug cord to LIGHTS
and
Remove plastic CAP at right end for
2
1
1
only LIGHT
, DO NOT remove CAP
2
from LIGHT
.
P
A
C
1
LIGHT
Cord behind
2
LIGHT
Insert LIGHT COVER to holes pre
drilled on front edge of TOP panel.
Insert LIGHT to LIGHT COVER
3
4
~10~
STEP 7 : DOORS INSTALLATION
Insert DOORS onto
BOTTOM HINGES
1
2
3
2
5
6
4
2
5
3
6
4
2
5
2
3
6
3
4
2
4
5
2
3
5
6
3
4
6
2
4
5
2
3
5
6
3
4
6
4
5
2
5
6
6
4
2
5
3
6
4
2
5
3
6
5
6
1
2
Install TOP HINGES with HEX BOLTS (B)
2
NOTE :
Adjust final position of the door
before tightening the bolts and
move cellar into place, leaving
4” clearance all around cellar.
D
B
MAKE SURE CABINET ISAIRTIGHT!
Adjust the level by turning
(counter clockwise) the LEGS (H)
asneeded. Useacarpenter’slevel.
~11~
CONTROLS : PLUG IT IN (wait one minute) and ENJOY!
FEATURES:
- Default SET temperature 57º F/14º C (ideal for wine storage).
- Calibration option of the temperature sensor.
- Display of actual temperature by request.
- SET temperature range 52ºF-64ºF.
DISPLAY:
KEYS
- Digital temperature sensor.
- Dual display Fº/Cº.
- Settings are stored in memory for power failures.
- Pre programed software will reach the quietest most efficient operation.
57
OPERATION:
- The display will show the detected temperature until the temperature will fall within 3º of the SET POINT.
- If the temperature is above the default 57º F + 1º or other preset value, after a delay of 1 minute the fan will
start, followed by the compressor within the next minute.
- The unit will cycle ON/OFF based on the temperature reading. Fan speeds are automatically set by the controller
to achieve optimum performance.
- Minimum ON and OFF cycle times are imposed by software, to prevent "short cycling".
DISPLAY EXAMPLE
CONTROLLER
OPERATION
ACTION
BEFORE
57º
AFTER
56º
Actual temperature: PRESS
TO DISPLAY:
SET temperature:
PRESS and RELEASE
To increase:
PRESS
70º
57º
57º
57º
TO MODIFY SET
TEMPERATURE
(range is 52-64ºF):
PRESS
PRESS
once per degree
once per degree
57º
58º
To decrease:
57º
56º
The new value will be memorized and the controller will reset automatically.
PRESS and HOLD until buzzer sounds in 5 seconds
The new value will be memorized and the controller will reset automatically.
57º
14º
TO CHAANGE FROM
ºF to ºC: or ºC to ºF
57º
57º
F0
57º
F0
F1
-1
PRESS and HOLD
Wait 5 seconds
while holding PRESS
and RELEASE
TO CALIBRATE:
USE
or
for each degree of offset
will result in a warmer cabinet and a positive offset
F0
NOTE: A negative offset
will result in a cooler cabinet.
The new value will be memorized and the controller will reset automatically.
SAFETY FEATURES:
ALARM:
- If the temperature exceeds 72º F the unit will shut down, a sound warning will start and the dispaly will blink
alternating with the temperature reading.
AL
- This function is disabled in the first 4 hours “ Cool Down” period or after any reset for another 4 hours.
- The unit will restart and continue the cooling and cycling if the temperature falls below 72º F.
TO RESET: - Unplug and re plug the unit.
~12~
MAXIMUM CAPACITIES AND LOADING TIPS
Maximum capacities and sample loading arrangements for Vintage Keeper Tuscany wine cellars
are illustrated below. Note the variations in shelf height, to accommodate the widest variety of
bottle types and sizes. Standard Burgundy and Bordeaux bottles are best arranged with necks
facing out; some taller bottles may need to be arranged neck to neck. Never stack bottles more
than two rows high on a shelf; all shelves must be installed as directed. Avoid placing bottles
directly in front of the cooling unit’s circulating fan for more uniform temperature in cabinet.
MODEL 250
MODEL 500
13
7
26
14
1
2
13
7
26
14
Max 4" dia.
bottles
Max 4" dia.
bottles
14
8
14
14
14
7
7
7
4
7
14
14
14
14
14
14
14
14
14
14
7
7
7
7
7
7
7
7
7
7
Max
3.5" dia.
bottles
Max
3.5" dia.
bottles
14
12
7
7
7
7
6
4
14
14
14
14
14
14
40
7
7
14
40
7
8
7
3 rows
3" dia.
or 2 rows
4.5" dia.
3 rows
3" dia.
or 2 rows
4.5" dia.
20
20
8
4
220
�38
248
110
�19
124
Max: 506 3" bottles
Max: 253 3" bottles
*WARNING:
Bottles in black will be in the cold air stream and could block airflow efficiency in some
circumstances (warm or humid areas). This area of the cabinet should have the coldest
temperature and may be used as your “chilling” section.
~13~
TROUBLE SHOOTING GUIDE
Although each Vintage Keeper cooling unit has been carefully tested at every stage of manufacture, occasional problems
arise, the majority of which are due to rough or careless handling during shipping or installation. Other problems may
derive from improper cabinet assembly, power interruption or surge, low line voltage (less than your unit rating of 105V
or 240V), or failure to clean the unit regularly (see illustration below). The following may help you determine what the
problem may be; what steps you can take to correct it, and what further steps may be required. Additional Trouble-Shoot-
ing information and downloadable documents are available in the “Support” area of our web site: www.koolspace.com
Cleaning the coil
Coil is located at the top of
back panel.
Vacuum it periodically
IMPORTANT NOTE:
In order to provide maximum protection for your valuable wine collection, the following steps are highly advisable.
First and foremost, have your wine collection adequately insured. Second, install a battery-powered heat-sensitive alarm
to warn of any loss of cooling due to power interruption. Third, monitor your storage and ambient conditions on a regular,
daily basis. Fourth, install a high quality surge suppressor to protect against sudden power fluctuations. Fifth, clean the
unit as directed, on a regular basis, every 3 to 4 months vacuum the cooling unit coils (check our website for more info).
Sixth make sure to check water level in the DRAIN CUP periodically and empty. Be advised, also, that Drobot-Vintage
Keeper cannot in any event be liable or responsible for incidental or consequential damages.
IF:
CHECK:
THEN:
- Is the unit plugged in?
- Note that the unit has a 1-minute cautionary delay
between plugging in and full start-up; this is a built-in
COOLING UNIT - Is the power supply operational? safeguard to protect the compressor in the event of
DOES NOT RUN
AT ALL WHEN - Is the LED display functional?
PLUGGED IN
sudden power failure
- Note that the power supply must be a dedicated,
separately-fused and grounded 15 Amp, 120V line or 7.5
_Amp, 240 V line rated for your unit. Must not use an exten-
sion cord. Do not share the outlet with other appliances
- If the unit is receiving power yet fans or compressor fail
to run, unplug for ten minutes, then try again
- Is there any evidence of shipping
damage on the cooling unit or
packaging materials?
COOLING UNIT - Is the storage temp properly
RUNS BUT DOES set?
- Note that the unit may take a few days to achieve the
desired storage temperature, even in a properly located,
airtight cabinet
- Take steps to reduce ambient temperatures and
compensate for additional heat gain if any cabinet walls
receive direct sunlight
NOT COOL
SUFFICIENTLY
- Is the cabinet properly
assembled, with all joints air
tight?
- If gaps are visible at any panel joints, ensure that you
have tightened all cams in all panels, to ensure
an airtight seal as detailed in our instructions
- Take steps to improve circulation of air to and from the unit
- Adjust the door, if necessary, to seal tightly by
re-positioning the upper hinge and improving the cabinet
level
- Is the door properly adjusted to
seal tightly when closed?
- Is airflow to and from the
cooling unit unobstructed?
- Is the ambient air temperature
within the specified range?
- Increase your SET TEMPERATURE
- Clean the fan and grille areas
- If the problem persists, go to our website at
www.koolspace.com and perform the “cooling unit
diagnostic” in the support section.
- Are any exterior surfaces of the
cabinet exposed to sunlight?
~14~
LIMITED WARRANTY AND PRODUCT SUPPORT
ONE YEAR LIMITED WARRANTY
If your Koolspace cooling unit or cabinet fails to perform as designed within one year of the date of purchase, VINTAGE KEEPER INC.
warrants that, upon your request, it will be repaired or replaced, at our option, during the one year warranty period. This warranty
applies only to the first end-user purchaser of a Koolspace unit that is purchased and used in the continental United States or Canada
(excludes Alaska and Hawaii). It is not valid for subsequent purchasers, nor for units in use outside North America. The warranty period
for your Koolspace unit commences on the date you purchased it and expires one year thereafter.
PROOF OF PURCHASE
Within 10 days of purchase, complete and mail, fax or e-mail the registration sheet to VINTAGE KEEPER INC. Alternately, you may reg-
ister your warranty on our Internet web site, www.koolspace.com. WHEN YOU MAKE A WARRANTY CLAIM, YOU MUST
FORWARD A COPY OF YOUR ORIGINAL DATED BILL OF SALE TO ESTABLISH YOUR DATE OF PURCHASE.
IF YOU HAVE A PROBLEM WITH YOUR UNIT
Customer service and warranty problems are handled online at www.koolspace.com. You will find a comprehensive well-documented
and easy-to-use solution to almost any question or problem you may have. The inquiry forms are filled in on-line and connect you to
our representatives who will process your requests for warranty service. This is the quickest way to solve your problems. If you do not
have access to the internet you may call us from 9:00 a.m to 4:00 p.m EST, to request a WARRANTY CLAIM INFORMATION KIT. We can
fax or mail it to you. You can fill in the enclosed REQUEST FOR RETURN AUTHORIZATION CODE form and return it by mail or fax. We
can then promptly process your claim.
REPLACEMENT ?
At our option we may choose to offer you a replacement part or product rather than a repair. Upon your authorization to accept a
replacement unit and with appropriate security (credit card authorization), we will promptly ship a replacement unit. The replacement
may be a unit that has been reconditioned by VINTAGE KEEPER INC. The unit that needs service must be packed and returned to us,
shipping prepaid. Upon its receipt, we will release your credit card security. Go online to the SUPPORT section on our web site at
www.koolspace.com to request warranty service.
REPAIR ?
If we determine that your unit needs to be repaired rather than replaced we will issue you a Return Authorization Code. Go online to
the SUPPORT section of our web site at www.koolspace.com to request warranty repair service. Please save the original packaging
materials to facilitate shipment. Mark the Return Authorization Code clearly on the outside of the package, enclose a brief note
describing the problem and send the unit, shipping prepaid, to VINTAGE KEEPER INC.
WHAT MUST YOU DO?
Your unit is designed to perform with a minimum amount of user maintenance when installed and operated precisely as directed in
the manual. You are, however, responsible for the required user maintenance described in the manual, specifically, regular cleaning of
the condensor coil and fans. Also, you must take steps to protect the unit from sudden power surges. As with any sensitive electronic
device, your Koolspace unit may be damaged by power surges or spikes, including lightning strikes, acts of god, sudden interruptions
or prolonged low-voltage conditions, which are not covered by this Warranty. You must monitor your unit’s performance on a daily
basis. If there is an apparent problem or “Alarm” condition, you must disconnect the power supply to avoid potential damage to your
wine collection. It is your responsibility to insure your wine, and to take all reasonable and necessary precautions to safeguard its
condition.
WHAT THE WARRANTY DOES NOT COVER
This warranty covers only defects in materials and workmanship provided by VINTAGE KEEPER INC. and does not cover equipment
damage or malfunction from misuse, abuse, accident, act of God, or any unauthorized alteration or modification. The product must
have been installed and operated precisely as directed in the manual which accompanies each product. Improper return shipping,
inadequate packaging or shipping damage is not covered unless the unit is packaged and shipped in accordance with Koolspace
replacement procedures. Third party servicing of this product during the warranty period will also void the warranty, as will any evi-
dence of tampering or alteration to the serial number and or the original dated bill of sale.
REPLACEMENT AND REPAIR ARE YOUR ONLY REMEDIES
YOUR ONLY REMEDY UNDER THIS WARRANTY IS THE REPLACEMENT OR REPAIR OF YOUR ELIGIBLE PRODUCTAS DESCRIBEDABOVE. NEITHER
THIS WARRANTY NOR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL EXTEND BEYOND THE ONE-YEAR WARRANTY PERIOD. UNDER NO
CIRCUMSTANCES SHALL VINTAGE KEEPER INC. BE LIABLE FOR ANY SPECIAL INCIDENTAL, INDIRECT OR PUNITIVE DAMAGES OR FOR ANY
CONSEQUENTIAL DAMAGES, INCLUDING SPOILAGE OF WINE, EVEN IF VINTAGE KEEPER INC. KNOWS OR IS INFORMED THAT SUCH DAMAGES
ARE POSSIBLE. IT IS YOUR RESPONSIBILITY TO INSURE YOUR WINE, AND TAKE ALL REASONABLE, NECESSARY PRECAUTIONS TO SAFEGUARD
ITS CONDITION. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE
ABOVE EXCLUSION OR LIMITATION MAY NOTAPPLY TO YOU. NO RESELLER IS AUTHORIZED TO MODIFY THE TERMS OF THIS WARRANTY. ANY
ADDITIONAL WARRANTY OFFERED BY A RESELLER IS THE SOLE RESPONSIBILITY OF THAT RESELLER.
SERVICE AFTER YOUR WARRANTY EXPIRES
If your unit requires service after the one-year warranty period expires, you may have it serviced locally by any qualified HVAC
technician, or you may purchase a new unit at a special discount under our Extended Warranty Program. Please be ready to provide
model, serial number, credit card number and a copy of your original dated bill of sale. In addition, repair service is always available
direct from us at flat rates below the prevailing charges for local service. However, using our Extended Warranty Program for units
under 5 years old will always be a preferable solution to returning a unit for repair. Go online at www.koolspace.com to request
Repair Service or see our Extended Warranty Program.
~15~
CELLAR
nuvo
2 5 0 / 5 0 0
TM
ko o l s pac e
Toll free: 1-888-274-8813
www.koolspace.com
|