Metra Electronics DW 7501 User Manual

INST 7500  
KIT COMPONENTS  
6
#1  
Fig. A  
Fig. C  
99-7500  
DW-7501  
INSTALLATION  
INSTRUCTIONS  
ng #2  
rimplate  
r Bar  
APPLICATIONS  
Fig. B  
CAR  
MAZDA  
PAGE  
Fig. E  
323 1986-89*...............................................................................1  
323 1990-94*...............................................................................1  
626 (models w/factory receiver/tape deck/eq/pocket) 1986-92....2  
626 (models w/factory receiver/pocket) 1986-92* ...................... 2  
929 1988-91.................................................................................3  
B-Series Pickup 1986-93................................................................3  
Miata 1990-99.............................................................................. 4  
MPV 1989-95*.............................................................................. 4  
MX6 (models w/factory receiver/tape deck/eq/pocket) 1986-92...2  
MX6 (models w/factory receiver/pocket) 1986-92*....................... 2  
Protege 1990-94*......................................................................... 1  
RX-7 1986-91............................................................................... 5  
(8) 3/8" Phillips  
Screws  
Fig. D  
(6) ¾" Hex-head Screws  
(6) 3/8" Hex-head Screws  
(4) ½" Hex-head  
Screws  
B-SERIES PICKUP: Re-connect the battery terminal and test the unit for proper operation.  
Mount Bracket Set #1 to the Housing with (4) ½" Hex-head Screws supplied. Mount the  
head unit/kit assembly to the back of the dash trim bezel with (4) screws removed in step #1  
and re-attach the bezel. (see Fig. A)  
Bracket Set #1  
Equalizer  
Dummy  
Plate  
323 1986-89, 626 / MX6 (models using Radio Housing #2): Re-connect the battery terminal  
and test the unit for proper operation. Mount the head unit/kit assembly to the back of the dash  
trim bezel with(4) 3/8" Phillips Screwssupplied and re-attach the bezel. (see Fig. B)  
* For aftermarket DIN head unit installations, order Metra's 99-7501  
For models with pockets 3¾" or taller, order Metra's 99-7501  
TOOLS REQUIRED  
626 / MX6 (models using Radio Housing #1: Re-connect the battery terminal and test the  
unit for proper operation. Mount the head unit/kit assembly to the back of the dash trim bezel  
with(8) 3/8" Phillips Screwssupplied and re-attach the bezel. (see Fig. C)  
Phillips screwdriver  
323 1990-94, MPV, PROTEGE: Re-connect the battery terminal and test the unit for proper  
operation. Mount the head unit/kit assembly to the sub-dash with (4) ¾" Hex-head Screws  
supplied. (see Fig. D)  
929, MIATA, RX-7: Re-connect the battery terminal and test the unit for proper operation.  
Mount the head unit/kit assembly to the back of the dash trim bezel with (6) 3/8" Hex-head  
Screwssupplied and re-attach the bezel. (see Fig. E)  
Cutting tool  
© COPYRIGHT 2001 METRA ELECTRONICS CORPORATION  
rev. 300801  
Socket wrench  
7
MAZDA RX-7 1986-91  
MAZDA 626 / MX6 1986-92  
(models equipped with factory receiver/pocket)  
1
2
"A"  
1
2
"A"  
"A"  
A"  
"E"  
"E"  
"A"  
"A"  
Disconnect the negative battery terminal to  
prevent an accidental short circuit. Remove  
the ashtray and (2) screws exposed in the  
ashtray cavity. Unsnap the gear shifter trim  
and remove (2) screws exposed. Unsnap  
the climate control trim bezel and remove (2)  
screws exposed. Remove the dash trim  
bezel and disconnect the wiring. Remove  
(4) screws securing the factory head unit  
anddisconnectthewiring.  
Cut and remove all mounting tabs on Radio  
Housing #1 EXCEPT tabs "A".  
mounting tabs can be identified by the  
stamped letter on the back of each tab. Skip  
to the Installation Instructions for ALL  
VEHICLESonPage#5.  
The  
Disconnect the negative battery terminal to  
prevent an accidental short circuit. Remove  
the ashtray and (2) screws exposed.  
Remove the pocket and (2) screws exposed.  
Remove the radio trim bezel and disconnect  
the wiring. Remove (4) screws securing the  
factory dummy plate to the back of the bezel  
anddiscardtheplate.  
Cut and remove all mounting tabs on Radio  
The  
mounting tabs can be identified by the  
stamped letter on the back of each tab. Skip  
to the Installation Instructions for ALL  
VEHICLESonPage#5.  
Housing #2 EXCEPT tabs "E".  
MAZDA 626 / MX6 1986-92  
(models equipped with factory receiver/tape deck/eq/pocket)  
ALL VEHICLES  
"B"  
1
2
"B"  
"B"  
3a  
"B"  
"B"  
Fig. A  
"B"  
"B"  
"B"  
Fig. B  
Disconnect the negative battery terminal to  
Cut and remove all mounting tabs on Radio  
Housing #1 EXCEPT tabs "B". The  
mounting tabs can be identified by the  
stamped letter on the back of each tab. Skip  
to the Installation Instructions for ALL  
VEHICLESonPage#5.  
prevent an accidental short circuit. Remove  
the ashtray and (2) screws exposed.  
Remove the pocket and (2) screws exposed.  
Remove the radio trim bezel and disconnect  
the wiring. Remove (4) screws securing the  
factory dummy plate to the back of the bezel  
anddiscardtheplate.  
2-SHAFT HEAD UNITS: For models using Radio Housing #1, attach the Faceplate to the  
Housing. Slide the aftermarket head unit into the kit and secure with shaft nuts. (see Fig. A).  
For models using Radio Housing #2, slide the aftermarket head unit into the kit and secure  
withshaftnuts. (seeFig. B)  
5
2
MAZDA 929 1988-91  
MAZDA Miata 1990-99  
1
2
1
2
"A"  
"A"  
"A"  
"A"  
"A"  
"A"  
A"  
A"  
"A"  
"A"  
"A"  
"A"  
Disconnect the negative battery terminal to  
prevent an accidental short circuit. Reach  
behind the console and remove (2) nuts  
supporting the head unit carrier. Remove  
the factory head unit and disconnect the  
wiring..  
Cut and remove all mounting tabs on Radio  
Housing #1 EXCEPT tabs "A".  
mounting tabs can be identified by the  
stamped letter on the back of each tab. Skip  
to the Installation Instructions for ALL  
VEHICLESonPage#5.  
Disconnect the negative battery terminal to  
prevent an accidental short circuit. Remove  
(2) screws from the center console storage  
compartment. Remove (1) screw under the  
ashtray. Remove (1) screw from each side  
of the center console panel and remove the  
panel. Remove (1) screw exposed at the  
base of the dash trim bezel. Pop out the a/c  
vents and remove (2) screws exposed.  
Remove the dash trim bezel.  
Cut and remove all mounting tabs on Radio  
Housing #1 EXCEPT tabs "A".  
mounting tabs can be identified by the  
stamped letter on the back of each tab. Skip  
to the Installation Instructions for ALL  
VEHICLESonPage#5.  
The  
The  
MAZDA B-Series Pickup 1986-93  
1
2
MAZDA MPV 1989-95  
"C"  
1
2
"C"  
"E"  
"E"  
Disconnect the negative battery terminal to  
prevent an accidental short circuit. Remove  
(2) screws from each side of the radio trim  
bezel. Remove the ashtray and (1) screw  
from the rear support tab. Remove the radio  
trim bezel/sub-bracket assembly. Remove  
(4) screws securing the sub-bracket to the  
back of the radio trim bezel. Loosen (2)  
screws on top of the bezel and remove the  
sub-bracketfromthebezel.  
Cut and remove all mounting tabs on Radio  
Housing #1 EXCEPT tabs "C".  
mounting tabs can be identified by the  
stamped letter on the back of each tab. Skip  
to the Installation Instructions for ALL  
VEHICLESonPage#5.  
The  
Disconnect the negative battery terminal to  
prevent an accidental short circuit. Remove  
the ashtray and (2) screws exposed in the  
ashtray cavity. Remove the radio trim bezel  
and disconnect the wiring. Remove (4)  
screws securing the factory head unit and  
disconnectthewiring.  
Cut and remove all mounting tabs on Radio  
Housing #2 EXCEPT tabs "E".  
mounting tabs can be identified by the  
stamped letter on the back of each tab. Skip  
to the Installation Instructions for ALL  
VEHICLESonPage#5.  
The  
3
4

Rockford Fosgate RFB2122 User Manual
RCA DRC69705 User Manual
QSC Audio ISA 750 User Manual
Plextor Camera Accessories EZ5 User Manual
Pentax Binoculars 7X50PIF User Manual
Parrot EASYDRIVE EASYDRIVE User Manual
Panasonic DMCSZ8K User Manual
Multiquip Carrying Case pro12 User Manual
Motorola Cable Box DCT2000 User Manual
Kenwood KDC MP832U User Manual