Kenwood eXcelon KDC X693 User Manual

CD-RECEIVER

KDC-X993

KDC-HD942U

KDC-X693

KDC-MP642U

INSTRUCTION MANUAL

Take the time to read through this instruction manual.

Familiarity with installation and operation procedures will help you obtain the best

performance from your new CD-receiver.

For your records

Record the serial number, found on the back of the unit, in the spaces designated on the

warranty card, and in the space provided below. Refer to the model and serial numbers

whenever you call upon your Kenwood dealer for information or service on the product.

Model KDC-X993/ KDC-HD942U/ KDC-X693/ KDC-MP642U Serial number

US Residence Only

Before use

• If you experience problems during installation,

consult your Kenwood dealer.

• When you purchase optional accessories, check with

your Kenwood dealer to make sure that they work

with your model and in your area.

2WARNING

To prevent injury or fire, take the following

precautions:

• To prevent a short circuit, never put or leave any

metallic objects (such as coins or metal tools) inside

the unit.

• Characters that conform to ISO 8859-1 can be

displayed.

• The RDS feature won’t work where the service is not

supported by any broadcasting station.

• In this document, the description indicator will light

means a status is displayed. Refer to <Display Type

Selection> (page 10) for the details of the status

display.

Do not use this unit before canceling

Demonstration mode!

This unit is initially set on the Demonstration mode.

When using this unit for the first time, cancel the

<Demonstration mode setting> (page 27).

• The illustrations of the display and the panel

appearing in this manual are examples used to

explain more clearly how the controls are used.

Therefore, what appears on the display in the

illustrations may differ from what appears on the

display on the actual equipment, and some of the

illustrations on the display may be inapplicable.

How to reset your unit

• If this unit or the connected unit (disc auto changer,

etc.) fails to operate properly, press the Reset button.

The unit returns to factory settings when the Reset

button is pressed.

Reset button

Handling CDs

• Do not touch the recording surface of the CD.

• Do not stick tape etc. on the CD, or use a CD with

tape stuck on it.

• Do not use disc type accessories.

• Clean from the center of the disc and move

outward.

• When removing CDs from this unit, pull them out

horizontally.

• If the CD center hole or outside rim has burrs,

use the CD only after removing the burrs with a

ballpoint pen etc.

Cleaning the Unit

If the faceplate of this unit is stained, wipe it with a

dry soft cloth such as a silicon cloth.

If the faceplate is stained badly, wipe the stain off with

a cloth moistened with neutral cleaner, then wipe it

again with a clean soft dry cloth.

CDs that cannot be used

• CDs that are not round cannot be used.

•

Applying spray cleaner directly to the unit may affect its

mechanical parts. Wiping the faceplate with a hard cloth or

using a volatile liquid such as thinner or alcohol may scratch

the surface or erases characters.

Cleaning the Faceplate Terminals

If the terminals on the unit or faceplate get dirty, wipe

them with a clean soft dry cloth.

• CDs with coloring on the recording surface or CDs

that are dirty cannot be used.

• This unit can only play the CDs with

Lens Fogging

This unit may not correctly play discs which do not

have the mark.

• You cannot play a CD-R or CD-RW that has not been

finalized. (For the finalization process refer to your

CD-R/CD-RW writing software, and your CD-R/CD-

RW recorder instruction manual.)

When you turn on the car heater in cold weather,

dew or condensation may form on the lens in the

CD player of the unit. Called lens fogging, this

condensation on the lens may not allow CDs to play.

In such a situation, remove the disc and wait for the

condensation to evaporate. If the unit still does not

operate normally after a while, consult your Kenwood

dealer.

English

Basic Operation

[

]

Release

[SRC]

Microphone

AUX

Auxiliary

input

[FNC]

USB Terminal

[

]

[AUD]

Control

knob

[AUTO]

Auxiliary input

Connect a portable audio device with mini-plug

cable (3.5 ø).

General functions

Power/Source Select button: [SRC]

Turns on the power.

⁄

When the power is ON, select a source.

SRC Select mode 1: Press the [SRC] button and then

turn the Control knob or push it toward up or down.

To determine the selected source, press the Control

knob.

SRC Select mode 2: Pressing this button each time

switches between sources.

Tuner (“TUNER” or “HD Radio”) , USB or iPod (“USB” or

“iPod”), CD (“CD”) , Auxiliary input (“AUX”), and Standby

(“STANDBY”)

•

Use the mini-plug cable which is stereo type and does not

have any resistance.

•

The auxiliary input requires the setting made in “MENU” >

“AUX” of <Function Control> (page 6).

Text/Title scroll: Control knob

Scrolls the CD and audio file text display when

pushing toward up for at least 2 seconds.

Muting volume upon reception of phone call

When there is a call, “CALL” is displayed and the audio

system is paused.

Press at least 1 second to turn off the power.

When the call ends, “CALL” disappears and the audio

system comes back on.

The audio system comes back on when [SRC] is

pressed during a call.

⁄

•

The SRC Select mode can be set in “MENU” > “SRC Select” of

<Function Control> (page 6).

•

Auxiliary input source is initially set to “OFF”. Set “Built in

AUX” described in <Function Control> (page 6) to “ON”.

: Select “MENU” > “Built in AUX”

⁄

•

To use the TEL Mute feature, you need to hook up the MUTE

wire to your telephone using a commercial telephone

accessory. Refer to <Connecting Wires to Terminals> (page

51).

•

When an optional accessory is connected, the source name

for each device appears.

When connection of the iPod is recognized, the source

display changes from “USB” to “iPod”.

USB (iPod) source is recognized as CD source on the

connected unit.

Function Control: [FNC]

Pressing this button allows you to set various

functions using the Control knob. Refer to <Function

Control> (page 6).

Volume control: [AUD] knob

Turn the knob to adjust the volume.

Category Function of setup item

Subwoofer output: Control knob

SETUP

SOUND

Allows you to set up the environment.

Switches between ON (“SUBWOOFER ON”) and OFF

(“SUBWOOFER OFF”) each time pushing toward down

for at least 2 seconds.

Allows you to set up the display and color.

Allows you to set up the sound environment.

Allows you to set up the Bluetooth function.

Allows you to set up the each source function.

—

KDC-X993/ KDC-HD942U/ KDC-X693/ KDC-MP642U

Favorite Control: Control knob

You can recall the various registered functions by

turning the Control knob.

For example, you can recall and playback the playlist

in iPod while listening to Tuner.

Refer to <Favorite Control> (page 34).

Disc ejection: [0]

⁄

•

You can eject the disc for 10 minutes after switching off the

engine.

USB device/iPod play: USB Terminal

Connecting a USB device starts playback.

⁄

Tuner functions

•

For the playable audio file, media, and devices, refer to

<About Audio file> (page 45).

FM band: Control knob

Pause and play: Control knob

Switches between pause and play each time this

button is pressed.

Switches between FM1, FM2, and FM3 each time

pushing toward up.

AM band: Control knob

Switches to AM when pushing toward down.

USB device removing: [0]

Press this button for 2 seconds or longer to select the

remove mode, and the remove the USB device.

During the remove mode, “USB REMOVE” is displayed.

Tuning: Control knob

Changes the frequency when pushing toward left or

right.

Music search: Control knob

⁄

Changes the music when pushing toward left or right.

Fast reverses or forwards the music while keeping

pushing toward left or right. (No sound is output

while playing audio file.)

•

During reception of stereo stations the “ST” indicator is ON.

Tuning mode select: [AUTO]

• For KDC-HD942U/ KDC-X693/ KDC-MP642U:

Switches as follows each time this button is pressed.

• For KDC-X993: Switches as follows each time this

button is pressed for at least 1 second.

Tuning mode Display

Auto seek “Seek Mode : Auto1” Automatic search for a station.

Preset station “Seek Mode : Auto2” Search in order of the stations in

Folder search: Control knob

Changes the folder containing the audio file when

pushing toward up or down.

Operation

•

For the operation on iPod, enter <Music Search for iPod>

(page 13) is first to enter the search mode.

Search mode: [

]

seek

the Preset memory.

After pressing [ ] button, you can quickly search

songs with the Control knob. See <Music Search>

(page 13) for details.

Manual

“Seek Mode : Manual” Normal manual tuning control.

Disc & Audio file play functions

Hands-free phoning

Drop open the faceplate: Release

•

Push the faceplate on the left side, and return it to its

former position.

Microphone:

(Accessory of KDC-X993)

⁄

The microphone for the hands free phone is supplied.

When your voice cannot be recognized due to the

low microphone volume or noises in the vehicle,

adjust the microphone settings by selecting “MENU”

>“Mic Gain” of <Function Control> and “MENU” >“NR

Level” of <Function Control> (page 6).

Disc play: Disc slot

Starts playing when a disc is inserted.

When a CD is inserted, the “CD-IN” indicator is ON.

•

3 inch CD cannot be used. Attempt to insert using

an adapter can cause malfunction.

⁄

English

Function Control

Functions in the table below can be set up by using Function Control.

Displayed item is depending on currently selected

1 Enter Function Control mode

source or mode. The mark in Condition column

shows the condition to which the item is displayed.

: Can be set in other than standby state.

: Can be set in standby state.

Press the [FNC] button.

2 Select a Function group.

Push the Control knob towards right or left.

Pushing the Control knob towards left allows you

to set the preference items (“MENU”, “SETUP”, or

“SOUND”).

: Can be set while Audio file source of CD/USB/iPod.

: Can be set while Audio file source of CD/USB

(excluding iPod).

: Can be set while CD/ Disc changer source.

: Can be set while CD source.

Pushing the Control knob towards right allows you

to set the currently selected source function item

ON/OFF.

: Can be set while Disc changer source.

: Can be set during Tuner source.

: Can be set during FM reception.

: Can be set while accessing AUX source.

: Can be set while HD Radio source.

3 Select your desired setup item

Operation type

Movement between items Turn the Control knob.

Selection of item Press the Control knob.

Return to previous item Press the [FNC] button.

Select“Return”at the bottom of the item list.

Operation

: Can be set during Satellite radio source.

: Can be set only during playback of the iPod source.

: Can be set for sources other than the standby

source by setting “2 ZONE” of <Audio Setup> (page

28) to “ON”.

: Can be set while a cell-phone is connected.

: Sets “ILM MSC SYNC” in the menu to “OFF”.

: Refer to the reference page.

Repeat selection and determination until your

desired setup item is selected.

Example:

SETUP

SOUND

□ TRACK SCAN

□ DISC RANDOM

□ TRACK REPEAT

—

: Can be set during all sources.

The Control knob is used for entry, but how to use

the knob varies depending on the setting items.

: Press the Control knob to switch the settings.

SETUP

SOUND

□ TRACK SCAN

□ DISC RANDOM

□ TRACK REPEAT

: Push the Control knob towards left or right to

switch the settings.

Scr o ll： Au t o

C D R ead： 1

DEM O M o d e： OFF

Disp lay： OFF

: Turn the Control knob to switch the settings.

ILM M SC SY NC： OFF

1 sec. : Press the Control knob for 1 second to enter into

In this manual, the above selection is

indicated as

Select “MENU” > “DEMO Mode”.

Each item’s ”&” will be ”✓” when the source function

is set to ON.

the setting mode.

2 sec. : Press the Control knob for 2 seconds to enter into

the setting mode.

⁄

4 Make a setting

•

Refer to the respective page for information on how to set

the items with reference page number.

Push the Control knob towards up or down.

Press the Control knob to set the source function

item ON/OFF.

•

Only the items available to the current source are displayed.

The “SOUND” setting cannot be performed while the Dual

Zone function is used.

• Some items require you to keep pressing the

Control knob for 1 or 2 seconds so that you can

make a setting. For these items, the time during

which you need to keep pressing the Control

knob is displayed in the Entry column in seconds.

• For the functions accompanied by the

description of the setting procedure and so forth,

the reference page numbers are displayed.

*Factory setting

* Function of KDC-X993.

* Function of KDC-X693.

* Function of KDC-X693 with KCA-BT200.

* Function of KDC-MP642U.

* Refer to <Menu Glossary> (page 48).

5 Exit Function Control mode

Press the [FNC] button for at least 1 second.

KDC-X993/ KDC-HD942U/ KDC-X693/ KDC-MP642U

Source function item

Function

Setting

Entry

Setting overview

Condition Page

“iPod BY HAND”

“ON”/“OFF”*

When set to “ON”, allows you to operate iPod with the

control on the iPod.

“FILE SCAN”

“ON”/“OFF”*

When set to “ON”, plays the intro of the music in the

folder successively.

When set to “ON”, plays the music in the folder

randomly.

When set to “ON”, all songs in iPod are played at

random.

—

“FOLDER RDM”

“ALL RANDOM”

“FILE REPEAT”

“FOLDER REP”

“ON”/“OFF”*

When set to “ON”, plays the music repeatedly.

—

“ON”/“OFF”*

When set to “ON”, plays the music in the folder

repeatedly.

“TRACK SCAN”

“ON”/“OFF”*

When set to “ON”, plays the intro of the music on the

disc successively.

—

“DISC RANDOM”

“ON”/“OFF”*

When set to “ON”, plays the music on the disc randomly.

—

“MAGAZINE RDM”

“ON”/“OFF”*

When set to “ON”, plays the music in the disc changer

randomly.

“TRACK REPEAT”

“DISC REPEAT”

“ON”/“OFF”*

When set to “ON”, plays the music repeatedly.

—

“ON”/“OFF”*

When set to “ON”, plays the music on the disc

repeatedly.

“PTY SEARCH”

Select the Program Type and search for a station.

“AUTO MEMORY”

Memorizes 6 stations with good reception

automatically.

“Channel Scan”

Every receivable Channel is checked for 10 seconds.

Preference item

Category Item

Setting

Entry

1 sec.

Setting overview

Sets/Resets security code.

Condition Page

“MENU”

“Security Set”/

“Security Clear”

“SRC Select”

—

“1”*/“2”

Sets the source selection method.

“Skip Search”

“0.5%”*/

“1%”/“5%”/

“10%”

Sets the ratio of skip performed with <Music Search

for iPod>.

“Device Regist”*

—

1 sec.

“SPCL DVC Select”*

—

Allow registration of a special device that cannot be

registered normally.

Select a cell-phone subject to hands-free connection.

“Phone Selection”*

—

“Audio Selection”*

“Device Delete”*

—

1 sec. Select the Bluetooth audio player to be connected.

Cancel registration of the Bluetooth device.

—

1 sec.

“BT DVC Status”*

“PIN Code Edit”*

—

1 sec. Display the status of the Bluetooth device.

*

Specify the PIN code required when registering this unit

using the Bluetooth device.

1 sec.

“Auto Answer”*

“Mic Gain”*

“OFF”/“0S”–

“8S”* –“99S”

“–2”–“0”* –

“+2”

“–2”–“0”* –

“+2”

Answer a call automatically after lapse of the preset

time interval for automatic answer.

Adjusts the sensitivity of the built-in microphone for a

telephone call.

Reduces the noises generated by the surrounding

environment without changing the microphone

volume.

*

—

“NR Level”*

Next page 3

English

Function Control

Category Item

“SP Select”*

Setting

“Front”*/

Entry

Setting overview

Specify the voice output speaker.

Condition Page

*

“F-R”/“F-L”

“Call Beep”*

“ON”*/“OFF”

Output a beep from the speaker when a call comes in.

Display the firmware version and update the firmware.

*

“BT F/W Update”*

—

1 sec.

“Beep”

“OFF”/“ON”*

Setting the operation check sound (beep sound) ON/

OFF.

—

“Clock Adjust”

“Date Adjust”

—

1 sec. Sets the clock.

—

Sets the date.

1 sec.

“Date Mode”

“SYNC”

7 types

Sets the date display mode.

“OFF”*/“ON”

Synchronizing the RDS station time data and this unit’s

clock.

—

“DSI”

“OFF”/“ON”*

DSI (Disabled System Indicator) of the unit blinks when

the faceplate is removed.

—

“Illumi DIM”

“OFF”/“AUTO”*

/“MNAL1”/

“MNAL2”

Sets whether the illumination is dimmed in conjunction

with the light switch of the vehicle or it is dimmed

constantly.

*

“ILM Effect”**

“OFF”/“ON”*

Sets whether the key illumination color (KDC-X993/

KDC-X693) or brightness (KDC-HD942U/ KDC-MP642U)

is changed in conjunction with the key operation.

Sets whether the key illumination color (KDC-X993/

KDC-X693) or brightness (KDC-HD942U/ KDC-MP642U)

is changed in conjunction with the sound volume.

Turns off the display when no operation is performed.

—

“ILM MSC SYNC”

“OFF”*/“ON”

—

“Display”

“OFF”/“ON”*

*

“DISP DIM“

“OFF”/“AUTO”*

/“MNAL1”/

“MNAL2”

Dims the display part in conjunction with the light

switch of the vehicle.

“Contrast”

“DISP N/P”

“1”-“10”

Adjusting the display contrast.

—

“POSI1”/“2”

/“NEGA1”/“2”

“OFF”/“ON”*

Switches the panel display between positive or

negative.

Turns on/off the built-in amplifier.

*

“AMP”

*

“Zone2”

“REAR”*/

“FRONT”

—

Specifies the destination of AUX input sound when the

Dual Zone function is turned on.

Controls the connected LX amplifier.

“AMS Control”**

—

“TI”**

“OFF”*/“ON”

“OFF”/“ON”*

Switches to the traffic information automatically when

the traffic bulletin starts.

Switches to Monaural to decrease noise when

reception is poor.

—

“CRSC”***

—

“Receive Mode”

“AUTO”*/

“DIGITAL”/

“ANALOG”

“00”-“50”

Sets the receive mode of HD Radio.

*

1 sec.

“Tag Memory”

Displays the tag memory usage of HD Radio. Up to 50

tags can be registered to this unit.

“Tagging”

“ESN=”

“0FF”/“ON”*

Turns ON / OFF the tag memory function of HD Radio.

—

“Auto”*/

“Manual”

—

Displays the Electronic Serial Number of satellite radio.

—

“Name Set”

“Scroll”

Sets the display when switched to AUX source.

Specifies whether the text is scrolled automatically.

—

1 sec.

—

“Favorite Delete”

“Built in AUX”

Deletes Favorite Preset Memory.

“OFF”*/“ON”

“1”*/“2”

Sets whether to display AUX during source selection.

—

“CD Read”

Sets the CD read mode.

*

“DEMO Mode”

“OFF”/“ON”*

2 sec. Specifies whether to enable demonstration.

KDC-X993/ KDC-HD942U/ KDC-X693/ KDC-MP642U

Category Item

“SETUP” “Display

Setting

“DISP TYPE

[A] – [D]”

Entry

Setting overview

Sets the display pattern.

Condition Page

“Type Select”

—

Select”

“Graphic Select” “Graphic 1 –2”

Sets the Type C spectrum analyzer display.

Sets the Type A side display.

—

“Side Select”

“Text Select”

“Status”

3 types

—

Sets the Type A/B/C text display.

Sets the Type A Status display.

Appear/

Disappear

“Variable Scan”*

/“Color 1”–

“Color 10”/

“User”

“Color

Select”**

“All”

Sets the panel and display illumination color.

“Display”

“Right”

“Left”

Sets the display illumination color.

Sets the right side of panel illumination color.

Sets the left side of panel illumination color.

Sets the sound quality.

“SOUND”

“Control” “EQ”

“Bass Boost”

—

“OFF”*/

Sets the Bass Boost level in two steps.

—

“Step1” –“2”

“OFF”/“STEP1”

/ “2”/“3”*

“HIGHWAY-

SOUND”

Compensates the low volume or bass sound being lost

by road noises to make vocal sound clearer.

*

“Supreme+”

“ON”*/“OFF”

Turns ON/OFF the Supreme plus function.

“Position”

“Cabin”

—

Compensates the sound environment in accordance

with the listening position.

Selects the car type to compensate the distance

difference between each speaker.

Sets the connected speaker, speaker size, and

installation position.

Makes fine adjustment of the compensation value

specified at Cabin.

Makes fine adjustment of the X’Over value specified at

Speaker.

Registering the value setup by Sound Control. Recalling

the sound setup registered by <Audio Preset Memory>.

Registering the value setup by Sound Control.

“Setup”

“Compact”etc.

“Speaker”

“DTA”

—

“X’Over”

“Recall”

“Memory”

“Preset”

“DSP Set”

“Bypass”/

“Through”*

—

Setting “Bypass” passes the DSP function.

Setting “Through” activates the DSP function.

Calls by recognizing the registered voice.

—

“BT”

“Voice

Recognize”

“Voice Tag” “PB Name Edit”

—

Registers voice for voice recognition.

“PN Type Edit”

Registers voice to select the Phone number category

in Phonebook.

“SMS”

“SMS

Download”

“SMS Inbox”

—

Download a short message.

Display the received short message.

•

Location played with “FILE SCAN”

- Audio file: First 10 seconds

- Music Editor media: First 10 seconds or the part picked by

Intro Skip.

During Intro Skip, turn the control knob left or right to

change the song.

The scan method depends on the Music Editor setting.

See the Music Editor help for details.

⁄

•

Strong electrical fields (such as from power lines) may cause

unstable sound quality when CRSC is turned ON. In such a

situation, turn it OFF.

•

The connected cell-phone must have the SMS function to

use the “SMS” function.

English

Display Settings

Display Type Selection

Text Display Selection

Shown below are examples of display types.

Changes displayed information on each source

following;

Display

Display Type

“TYPE [A]”

“TYPE [B]”

“TYPE [C]”

“TYPE [D]”

Displays 4 to 5 lines of text.

Displays a line of text and video.

Displays a line of text and the spectrum analyzer.

Displays the clock.

In Tuner source for KDC-X993/ KDC-X693

Information

Display

Frequency & Program Service name (FM)

Title & Artist name* (FM)

Station name* (FM)

“Frequency/PS”

“Title/Artist”

“Station Name”

“Radio Text Plus”

“Radio Text”

“Speana/Clock”

or“Clock”

1 Enter Display type selection mode

Select “SETUP” > “Display Select” > “Type

Select”.

For how to select Function Control item, refer to

<Function Control> (page 6).

Radio text plus* (FM)

Radio text (FM)

Spectrum analyzer & Clock (“TYPE [A]/[B]”)

or Clock (“TYPE [C]”)

Date

“Date”

Blank

“Blank”

2 Select the Display type

Turn the Control knob.

* Information of Radio text plus is displayed.

In HD Radio source for KDC-HD942U or

KDC-X993/ KDC-X693/ KDC-MP642U with

KTC-HR300

3 Exit Display type selection mode

Press the [FNC] button.

⁄

Information

Display

•

For how to switch the text display information, refer to

<Text Display Selection> (page 10).

Frequency

Station name

Title & Artist name

Album & Artist name

“Frequency”

“Station Name”

“Title/Artist”

“Album/Artist”

“Genre”

•

When “TYPE [A]” is selected, the status (ON/OFF indicator

of each function) can be displayed on the first line, and

the icon of the currently selected source and the text

information title can be displayed on the left side by the

following <Function Control> (page 6) operation.

Status display: Select “SETUP” > “Display Select” > “Status”

Side display: Select “SETUP” > “Display Select” >

“Side Select”

Genre

Spectrum analyzer & Clock (“TYPE [A]/[B]”)

or Clock (“TYPE [C]”)

“Speana/Clock”

or“Clock”

Date

“Date”

Blank

“Blank”

•

When “TYPE [C]” is selected, the spectrum analyzer can

be switched by the following <Function Control> (page

6) operation.

In Tuner source for KDC-MP642U

Information

Display

Frequency

“Frequency”

“Speana/Clock”

or“Clock”

“Date”

: Select “SETUP” > “Display Select” > “Graphic Select”

Spectrum analyzer & Clock (“TYPE [A]/[B]”)

or Clock (“TYPE [C]”)

Date

Blank

“Blank”

In CD & External disc source

Information

Display

Disc title

Track title

Play time

“Disc title”

“Track title”

“P-Time”

“Speana/Clock”

or“Clock”

“Date”

Spectrum analyzer & Clock (“TYPE [A]/[B]”)

or Clock (“TYPE [C]”)

Date

Blank

“Blank”

10 KDC-X993/ KDC-HD942U/ KDC-X693/ KDC-MP642U

In Audio file/ iPod source

Information

Title & Artist name

Album & Artist name

Folder name

1 Enter Text display selection mode

Select “SETUP” > “Display Select” >

“Text Select”.

For how to select Function Control item, refer to

<Function Control> (page 6).

Display

“Title/Artist”

“Album/Artist”

“Folder name”

“File name”

“P-Time”

“Time Bar”

“Speana/Clock”

or“Clock”

File name

Play time

2 Select the text display part

Push the Control knob towards up or down.

The selected text display part blinks.

Play time bar (iPod only)*

Spectrum analyzer & Clock (“TYPE [A]/[B]”)

or Clock (“TYPE [C]”)

Date

3 Select the text

Turn the Control knob.

“Date”

“Blank”

Blank

4 Exit Text display selection mode

Press the [FNC] button.

* Can be displayed only on the bottom line of “TYPE [A]”

text.

⁄

In Standby/ Auxiliary input source

•

If the selected display item does not have any

information, alternative information is displayed.

When LX-AMP is connected, the item setup by the

Display mode of LX-AMP is displayed. (Function of

KDC-X993/ KDC-X693)

Information

Source name

Clock

Display

“Source Name”

“Clock”

•

Date

“Date”

Blank

“Blank”

•

Some items cannot be selected depending on the

display type and row.

When selecting “Folder name” while playing with

iPod, names will be displayed depending on currently

selected browsing items.

In SIRIUS/ SAT source (Optional)

Information

Channel Name

Music Title

Display

“Channel Name”

“Song Title”

•

If the iPod Control by Hand Mode is set to on while

playing the iPod, “iPod by Hand Mode” is displayed.

If all characters cannot be displayed while playing with

iPod, the file number in the list is displayed.

Artist Name

“Artist Name”

“Composer name”

“Category Name”

“Label Name”

“Comment”

Composer name

Category Name

Label Name

Information

Music title

Folder name

File name

Display

“TITLE***”

“FLD***”

“FILE***”

Comment

Channel Number

Spectrum analyzer & Clock (“TYPE [A]/[B]”)

or Clock (“TYPE [C]”)

Date

“Channel Number”

“Speana/Clock”

or“Clock”

“Date”

Blank

“Blank”

In XM source (Optional)

Information

Display

Channel Name

Title

“CHANNEL NAME”

“TITLE”

Name

“NAME”

Category Name

Channel Number

Spectrum analyzer & Clock (“TYPE [A]/[B]”)

or Clock (“TYPE [C]”)

“CATEGORY NAME”

“CHANNEL NUMBER”

“Speana/Clock”

or“Clock”

Date

“Date”

Blank

“Blank”

English

Display Settings

Function of KDC-X993/ KDC-X693

Auxiliary Input Display Setting

Illumination Color Selection

Selects the display when changing to Auxiliary

input source.

Selecting the Illumination Color of the panel.

1 Select the AUX source

Press the [SRC] button.

1 Enter Illumination color selection mode

Select “SETUP” > “Color Select”.

For how to select Function Control item, refer to

<Function Control> (page 6).

2 Enter Auxiliary input display setting mode

Select “MENU” > “Name Set”.

For how to select Function Control item, refer to

<Function Control> (page 6).

2 Select the place where you want to set the

Illumination Color

Place

All

Display

Right

Left

Display

“All”

“Display”

“Right”

“Left”

3 Enter Auxiliary input display setting mode

Press the Control knob for at least 1 second.

The presently selected Auxiliary input display is

displayed.

4 Select the Auxiliary input display

Turn the Control knob.

“AUX”/ “DVD”/ “PORTABLE”/ “GAME”/ “VIDEO”/ “TV”

Turn the Control knob and push the center

when the desired item is displayed.

3 Select the Illumination Color

Turn the Control knob and push the center

when the desired item is displayed.

Select the color from “Variable Scan”/ “Color1” —

“Color 10”/ “User”.

5 Exit Auxiliary input display setting mode

Press the [FNC] button.

⁄

•

When operation stops for 10 seconds, the name at that

time is registered, and the Auxiliary input display setting

mode closes.

Creating “User” color

•

The Auxiliary input display can be set only when the

built-in auxiliary input or the auxiliary input of optional

KCA-S220A is used. On the KCA-S220A, “AUX EXT” is

displayed by default.

AUX source is initially set to “OFF”. Before display setting,

set “Built in AUX” described in <Function Control> (page

6) to “ON”.

You can create your original color during the

selection from “Color1” — “Color10.”

The color you created can be called when you

select “User”.

1. Press the Control knob for at least 1 second.

Enter the detail color adjustment mode.

2. Set the color.

•

: Select “MENU” > “Built in AUX”

Operation type

Operation

To select the color to adjust. Push the Control knob towards right

(red, green, or blue)

To adjust color.

(Range: 0 – 9)

or left.

Turn the Control knob or push it

towards up or down.

3. Press the Control knob.

Exit the detail color adjustment mode.

4 Exit Illumination color selection mode

Press the [FNC] button.

12 KDC-X993/ KDC-HD942U/ KDC-X693/ KDC-MP642U

Music disc/Audio file Operation

Function of Audio file/ Internal CD source

Function of iPod

Music Search

Music Search for iPod

Selecting the music you want to listen to from the

device or media being played now.

Search for the song (in iPod) you want to play.

1 Enter Music Search mode

Press the [ ] button.

1 Enter Music Search mode

Press the [ ] button.

“SEARCH” is displayed.

2 Search for music

Operation type

Operation

Displays the current Audio file name.

Movement between items Turn the Control knob.

2 Search for music

Skip Search *¹

Push the Control knob towards right or left.

Selection of item

Return to previous item

Return to Top menu

Press the Control knob.

Audio file

Push the Control knob towards up.

Push the Control knob towards up for at

least 1 second.

Push the Control knob towards down. Refer

to the next section <Searching for Music

by Initial>.

Operation type

Movement between

folders/files

Operation

Turn the Control knob or push it towards

up or down.

Press the Control knob or push it towards

right.

Search by initial

Selection of folder/file

Return to previous folder Push the Control knob towards left.

Scroll bar is displayed on the right side of the

screen.

Return to root folder

Push the Control knob towards left for at

least 1 second.

Cancelling the Music Search mode

Press the [ ] button.

“8” or “7” beside the displayed folder name

indicates that this folder is preceded or followed by

another folder.

⁄

•

File name is displayed with “¡” indicator.

*¹Skip Search: The number of songs to be skipped is

determined by the ratio of the total number of songs

in the list which is selected now. Set the ratio with

“Skip Search” in <Function Control> (page 6). Keep

pushing Control knob for 3 seconds or longer skips

songs at 10% irrespective of the setting.

Internal CD source

Operation type

Operation

Movement between track Turn the Control knob or push it towards

up or down.

Selection of track

Press the Control knob.

•

Characters that are included in a song name but cannot

be displayed are left blank. If no character included in a

song name cannot be displayed, the browse item name

and digits are displayed.

Return to first track

Push the Control knob towards left for at

least 1 second.

Cancelling the Music Search mode

Press the [ ] button.

Items

Playlists

Artists

Albums

Songs

Display

“PLIST***” Podcasts

“ART***”

“ALB***”

“PRGM***”

Items

Display

“PDCT***”

“GEN***”

“COM***”

Genres

Composers

⁄

•

Music Search cannot be performed during Random play.

English

Music disc/Audio file Operation

Function of iPod

Searching for Music by Initial

All Random

You can select an alphabetic character from the list

in the browse item (artist, album, etc.) selected now.

All songs in iPod are played at random.

Enter All random mode

1 Enter Music Search mode

Select “ALL RANDOM”.

For how to select Function Control items, refer to

<Function Control> (page 6).

Press the [ ] button.

2 Start the alphabet search

Push the Control knob towards down.

“A B C …” is displayed.

⁄

•

The time required to turn on the all random function

may become longer depending on the number of songs

in iPod or the folder structure.

•

If you can not search for a song by an alphabetic

character in the browse item selected now, the data on

the screen does not change.

•

Turning on the all random function changes the iPod

browse item to “Songs”. This browse item will not change

even if the all random function is turned off.

3 Select the initial to be searched for

Operation type Operation

Move to the next character. Turn the Control knob or push it towards

right or left.

Move to the next row.

Push the Control knob towards up or

down.

Function of iPod

iPod Control by Hand Mode

Allows you to operate iPod with the control on the

iPod.

4 Determine the selected initial

Press the Control knob.

Start search. When search is completed, the music

search mode is selected again at the selected

character position.

Enter iPod Control by Hand Mode

Select “iPod BY HAND”.

For how to select Function Control items, refer to

<Function Control> (page 6).

Cancelling the alphabet search

Press the [ ] button.

⁄

•

iPod will be paused when Hand mode is turned ON

during playback.

•

The time of search by alphabet may become long

depending on the number of songs in iPod or the folder

structure.

In the iPod Control by hand mode, iPod cannot be

operated using this unit.

This mode is not compatible with music information

display. The display will show “iPod by Hand Mode”.

iPod can be operated when it conforms to the iPod

control function.

•

When selecting an initial in the alphabet search, entering

“*” searches symbols and entering “1” searches digits.

If the first character string begins with an article “a”, “an”,

or “the” in the alphabet search mode, it is searched for in

defiance of the article.

14 KDC-X993/ KDC-HD942U/ KDC-X693/ KDC-MP642U

Function of remote control

Basic Operation of Disc Changer

(Optional)

Direct Music Search

Searchs the music by entering the track number.

Selecting CD changer source

Press the [SRC] button.

Select the “CD CHANGER” display.

1 Enter the music number

Press the number buttons on the remote

control.

Music search

Push the Control knob towards right or left.

2 Search the music

Press the [4] or [¢] button.

Disc Search

Push the Control knob towards up or down.

Cancelling Direct Music Search

Press the [38] button.

⁄

•

Direct Music Search cannot be performed during playing

of iPod, “Music Editor” media, Random play, or scan play.

Function of disc changers with remote control

Direct Disc Search

Searchs the disc by entering the disc number.

1 Enter the disc number

Press the number buttons on the remote

control.

2 Search the disc

Press the [FM+] or [AM–] button.

Cancelling Direct Disc Search

Press the [38] button.

⁄

•

Direct Disc Search cannot be performed during playing

of Random play or scan play.

•

Input “0” to select disc 10.

English

Function of KDC-X993/ KDC-X693/ KDC-MP642U

Tuner Operation

Auto Memory Entry

Preset Tuning

Putting stations with good reception in the memory

automatically.

Recalling the stations in the memory.

1 Enter Preset Tuning Select mode

Press the [ ] button.

1 Enter Auto Memory Entry mode

Select “AUTO MEMORY”.

For how to select Function Control items, refer to

<Function Control> (page 6).

2 Select a desired station in the memory

Turn the Control knob.

3 Recall the station

2 Open Auto Memory Entry

Press the Control knob.

Turn the Control knob to select “YES”, and then

press the Control knob.

Cancelling Preset Tuning

Press the [ ] button.

When 6 stations that can be received are put in the

memory, auto memory entry closes.

Function of remote control

Station Preset Memory

Direct Access Tuning

Putting a station in the memory.

Entering the frequency and tuning.

1 Select the frequency to put in the memory

1 Enter Direct Access Tuning mode

Press the [DIRECT] button on the remote

control.

Push the Control knob towards right or left.

2 Enter Preset Memory mode

Press the [ ] button.

“– – – –” is displayed.

2 Enter the frequency

3 Select the number to put in the memory

Press the number buttons on the remote

Turn the Control knob.

control.

Example:

4 Determine the number to put in the memory

Press the Control knob for at least 2 seconds.

Desired frequency Press button

Cancelling the Preset Memory mode

Press the [ ] button.

92.1 MHz (FM)

810 kHz (AM)

[0], [9], [2], [1]

[0], [8], [1], [0]

Cancelling Direct Access Tuning

Press the [DIRECT] button on the remote

control.

⁄

•

You can enter the FM band frequency in steps of a

minimum of 0.1 MHz.

16 KDC-X993/ KDC-HD942U/ KDC-X693/ KDC-MP642U

Function of KDC-X993/ KDC-X693

PTY (Program Type)

Program Type Preset

Selecting the Program Type below and searching

for a station;

Putting the Program Type in the Preset button

memory and quick recall.

Program Type Display

Presetting the Program Type

Speech

Music

“Speech”

“Music”

“News”

Jazz

“Jazz”

1 Select the Program Type to preset

Refer to <PTY (Program Type)> (page 17).

Classical

R & B

“Classicl”

“R&B”

News

Information

Sports

Talk

“Inform”

“Sports”

“Talk”

Soft R & B

Language

Religious Music “RelMusc”

Religious Talk “RelTalk”

Personality

Public

College

“SoftR&B ”

“Language”

2 Enter Program Type Preset mode

Press the [ ] button.

3 Select the number to put in the memory

Turn the Control knob.

Rock

“Rock”

Classic Rock

Adult Hits

Soft Rock

Top 40

Country

Oldies

“ClsRock”

“AdltHit”

“Soft Rck”

“Top 40”

“Country”

“Oldies”

“Soft”

“Persnlty”

“Public”

“College”

“Weather”

4 Determine the number to put in the memory

Press the Control knob for at least 1 second.

Weather

Recalling the preset Program Type

1 Enter PTY mode

Refer to <PTY (Program Type)> (page 17).

Soft

Nostalgia

“Nostalga”

2 Enter Program Type Preset mode

Press the [ ] button.

•

Speech and Music include the Program type shown

below.

Music: Black character item.

Speech: White character item.

3 Select a desired Program Type in the memory

Turn the Control knob.

1 Select PTY mode

Select “PTY SEARCH”.

4 Recall the Program Type

Press the Control knob.

For how to select Function Control items, refer to

<Function Control> (page 6).

2 Select the Program Type

Turn the Control knob.

Function of KDC-X993/ KDC-X693

Registration of a Station as a PTY

3 Search for the selected Program Type station

Push the Control knob towards right or left.

Registering a Program Type for stations with no PTY

data.

4 Exit PTY mode

Press the Control knob.

1 Receive the station you want to register

2 Select the Program Type to register

⁄

Refer to <PTY (Program Type)> (page 17).

•

This function cannot be used during a traffic bulletin or

AM reception.

3 Register the Program Type

Press the [FNC] button for at least 2 seconds.

•

When the selected Program Type is not found, “No PTY”

is displayed. Select another Program Type.

Confirming the Program Type

Press the [FNC] button.

The Program Type is displayed for 3 seconds.

4 Exit PTY mode

Press the Control knob.

English

Function of KDC-HD942U

KDC-X993/ KDC-X693/ KDC-MP642U with KTC-HR300 (Optional Accessory)

HD Radio tuner control

Auto Memory Entry

Preset Tuning

Putting stations with good reception in the memory

automatically.

Recalling the stations in the memory.

1 Enter Preset Tuning Select mode

Press the [ ] button.

1 Enter Auto Memory Entry mode

Select “AUTO MEMORY”.

For how to select Function Control items, refer to

<Function Control> (page 6).

2 Select a desired station in the memory

Turn the Control knob.

3 Recall the station

2 Open Auto Memory Entry

Press the Control knob.

Turn the Control knob to select “YES”, and then

press the Control knob.

Cancelling Preset Tuning

Press the [ ] button.

When 6 stations that can be received are put in the

memory, auto memory entry closes.

Station Preset Memory

Putting a station in the memory.

1 Select the frequency to put in the memory

Push the Control knob towards right or left.

2 Enter Preset Memory mode

Press the [ ] button.

3 Select the number to put in the memory

Turn the Control knob.

4 Determine the number to put in the memory

Press the Control knob for at least 2 seconds.

Cancelling the Preset Memory mode

Press the [ ] button.

18 KDC-X993/ KDC-HD942U/ KDC-X693/ KDC-MP642U

Function of remote control

HD Radio Tagging (iTunes Tagging)

Direct Access Tuning

Using an iTunes Tagging enabled HD Radio you can

tag your music. When you hear a song you enjoy

on your local HD Radio station, you only have to

press the Control knob. The song’s information

will then be saved on this unit. The saved songs

will then show up in a playlist called “Tagged” in

iTunes the very next time you sync your iPod to

your computer. So then you just need to click and

then easily buy and download the song you were

tagging directly from the Apple iTunes Music Store.

Entering the frequency and tuning.

1 Enter Direct Access Tuning mode

Press the [DIRECT] button on the remote

control.

“– – – –” is displayed.

2 Select Tuning item

Press the [DIRECT] button on the remote

control.

Pressing the [DIRECT] button each time switches

the following tuning items as follows.

1 Enter HD Radio tagging mode

Press the Control knob.

Tuning item

Frequency

Channel

Cancelling Direct Access Tuning

Display

“– – – –”

“CH –”

—

“

” will be indicated on the display when song

TAG

information can be registered.

⁄

•

Turn “ON” the “MENU” > “Tagging” of <Function Control>

(page 6) when using this function.

3 Enter the frequency or Channel

Press the number buttons on the remote

control.

•

Up to 50 TAGs (song’s information) can be registered to

this unit. When iPod is connected, the TAG information

registered to this unit is transferred to the connected

iPod.

Example of frequency input:

•

The memory usage can be checked by selecting “MENU”

> “Tag Memory” of <Function Control> (page 6).

Desired frequency Press button

92.1 MHz (FM)

810 kHz (AM)

[9], [2], [1]

[8], [1], [0]

4 Do Direct Access Tuning

Press the [4] or [¢] button.

⁄

•

You can enter the FM band frequency in steps of a

minimum of 0.1 MHz.

English

Function of KDC-X993

KDC-HD942U/ KDC-X693/ KDC-MP642U with KCA-BT200 (Optional Accessory)

Operation of hands-free phoning

your cell-phone to return to the hands-free talk mode.

Before Use

Adjusting the Voice Volume during a Call

Turn the [AUD] knob.

• For details on the Bluetooth cell-phone with the

hands-free function, see <About the Cell-Phone>

(page 46).

• You need to register your cell-phone before using

it with this unit. For more details, see <Registering

Bluetooth device> (page 36).

• If you have registered two or more cell-phones,

you need to select one of them. For more details,

see <Selecting the Bluetooth device You Wish to

Connect> (page 37).

Call waiting

Answering Another Incoming Call with the

Current Call Suspended

• To use the Phone Book, it must be downloaded to

this unit in advance. For details, see <Downloading

the Phone Book> (page 37).

• “BT” indicator is lit when a cell-phone is connected

to this unit.

1 Press the [AUD] button.

2 Turn the Control knob or push it towards up

or down. Select the “ANSWER” display.

3 Press the [AUD] button.

Answering another Incoming Call after

Terminating the Current Call

Press the [SRC] button or press the [ ] button

for at least 1 second.

Receiving a call

Continuing the Current Call

Answering a Phone Call

Press the [AUD] button.

1 Press the [AUD] button.

⁄

2 Turn the Control knob or push it towards up

•

The following operations disconnect the line:

- Insert a CD.

or down. Select the “REJECT” display.

3 Press the [AUD] button.

- Connect a USB device.

•

The name of the calling party is displayed if it has already

been registered in the Phone Book.

Answering the Waiting Call after Terminating

the Current Call

Press the [SRC] button or press the [ ] button

for at least 1 second.

Rejecting an Incoming Call

Press the [SRC] button or press the [ ] button

for at least 1 second.

Switching between the Current Call and Waiting

Call

Press the [AUD] button.

Each pressing of this knob switches the calling

party.

During a call

Disconnecting a Call

Press the [SRC] button or press the [ ] button

for at least 1 second.

Other functions

Switching to the Private Mode

Press the Control knob.

Switches between Private talk (“PRIVATE”) and

Hands-free talk each time this button is pressed.

Clearing the Disconnection Message

KDC-X993:

Press the [ ] button.

KDC-HD942U/ KDC-X693/ KDC-MP642U:

Press the [ ] button for at least 1 second.

“HF Disconnect” disappears.

⁄

•

Depending on the type of your cell-phone, switching

to the private talk mode may select the source that was

used before commencing the hands-free connection.

If this happens, the source cannot be switched back to

the hands-free talk mode by operating this unit. Operate

20 KDC-X993/ KDC-HD942U/ KDC-X693/ KDC-MP642U

Making a call

Speed dialing (Preset dial)

1 Enter dialing method mode

KDC-X993:

1 Enter dialing method mode

KDC-X993:

Press the [ ] button.

KDC-HD942U/ KDC-X693/ KDC-MP642U:

Press the [ ] button for at least 1 second.

KDC-HD942U/ KDC-X693/ KDC-MP642U:

Press the [ ] button for at least 1 second.

2 Press the Control knob.

2 Select a dialing method

Select the “DIAL”, “PHONE BOOK”, “OUT-CALL”,

“IN-CALL”, or “MISSED CALLS” display.

Press the Control knob.

“DIAL” » “INITIAL” » “PHONE BOOK” » “OUT-CALL” »

“IN-CALL” » “MISSED CALLS”

Methods of operations in the above modes are

described below.

3 Enter preset dial mode

Press the [ ] button.

4 Select the number you want to recall from the

memory

Turn the Control knob or push it towards up or

down.

3 Exit the dialing method mode

Press the [ ] button.

5 Press the Control knob.

Phone number is displayed.

Dial a number

6 Exit the preset dial mode

Press the [ ] button.

1 Enter dialing method mode

KDC-X993:

Press the [ ] button.

7 Make a call

Press the Control knob for at least 1 second.

KDC-HD942U/ KDC-X693/ KDC-MP642U:

Press the [ ] button for at least 1 second.

⁄

•

You need to register the preset dial number. (page 23)

2 Select the number dial mode

Press the Control knob.

Select the “DIAL” display.

3 Enter a phone number

Press the number ([1] – [0]), #([FM]), *([AM]), or

+([¢]) button on the remote controller.

4 Make a call

Press the [DIRECT] button on the remote

controller.

To erase the entered phone number digit by

digit:

Press the [4] button on the remote controller.

⁄

•

You can input max 32 digits.

English

Function of KDC-X993

KDC-HD942U/ KDC-X693/ KDC-MP642U with KCA-BT200 (Optional Accessory)

Operation of hands-free phoning

Calling a number in the Phone Book

Calling a number in the call log

1 Enter dialing method mode

KDC-X993:

1 Enter dialing method mode

Press the [ ] button.

KDC-HD942U/ KDC-X693/ KDC-MP642U:

Press the [ ] button for at least 1 second.

2 Select the call log mode

Press the Control knob.

Select the “OUT-CALL” (outgoing call), “IN-CALL”

(incoming call), or “MISSED CALLS” (missed call)

display.

2 Select the Phone Book mode

Press the Control knob.

Select the “INITIAL” display, proceed to step 3.

Select the “PHONE BOOK” display, proceed to step

3 Select a name or phone number

Turn the Control knob or push it towards up or

down.

3 Select the initial to be searched for

Switching between Display Modes

Press the [FNC] button.

Operation type

Operation

Move to the next character. Turn the Control knob or push it towards

right or left.

Pressing this button each time switches between

name and telephone number.

Move to the next row.

Push the Control knob towards up or

down.

4 Make a call

Press the Control knob for at least 1 second.

Determine the selected initial. Press the Control knob.

⁄

4 Select the name

Operation type

Move to the next phone

number.

•

The outgoing call list and the incoming call list, and the

missed call list are the lists of calls originated from and

received at this unit. They are not the ones stored in the

cell-phone memory.

Operation

Turn the Control knob or push it

towards up or down.

Push the Control knob towards right

or left.

Move to the next name.

Switching between Display Modes

Press the [FNC] button.

Pressing this button each time switches between

name and telephone number.

5 Make a call

Press the Control knob for at least 1 second.

⁄

•

During search, a non-accent character such as “u” is

searched for instead of an accent character such as “ü”.

22 KDC-X993/ KDC-HD942U/ KDC-X693/ KDC-MP642U

Make a voice dialing call

Registering to the Preset Dial Number

List

1 Enter voice recognize mode

Select “BT” > “Voice Recognize”.

For how to select Function Control item, refer to

<Function Control> (page 6).

1 Enter the phone number you wish to register

Enter the phone number with reference to the

following:

Dial a number/ Calling a number in the call log/

Calling a number in the Phone Book

“Ready” is displayed.

2 Press the Control knob.

“PB Name?” is displayed.

When a beep is heard, utter the name within 2

second.

2 Enter Preset Memory mode

Press the [ ] button.

3 Select the number to put in the memory

Turn the Control knob or push it towards up or

down.

3 “PN Type” is displayed.

When a beep is heard, utter the category within 2

second.

4 Determine the number to put in the memory

Press the Control knob for at least 1 second.

4 Make a call

Press the Control knob for at least 1 second.

•

This step is the same as step 3 of the procedure in

<Calling a number in the Phone Book>. You can make a

call or select a category.

Exit the Preset Memory mode

Press the [ ] button.

⁄

•

If your voice cannot be recognized, a message is

displayed. Pressing the Control knob allows you to retry

voice input. (page 54)

Both the name and category requires registration of a

voice tag. (page 39)

Audio sound is not output during voice recognize.

Display of phone number type

(category)

•

The category items in the Phone Book are displayed

as follows:

Display

Information

“GENERAL”/“

”

General

“HOME”/“

“OFFICE”/“

“MOBILE”/“

“OTHER”/“

”

Home

Office

Mobile

Other

”

English

Bluetooth Audio Operation

Before Use

• For details on the Bluetooth Audio player which

can be connected, see <About the Bluetooth Audio

player> (page 47).

• You need to register your Bluetooth Audio player

before using it with this unit. For more details, see

<Registering Bluetooth device> (page 36).

• You to select the Bluetooth audio player you wish to

connect. Refer to <Selecting the Bluetooth device

You Wish to Connect> (page 37).

Basic Operation

Selecting Bluetooth Audio source

Press the [SRC] button.

Select the “BT Audio” display.

For how to select source item, refer to <Power/

Source Select button> of <Basic Operation> (page

4).

Pause and play

Press the Control knob.

Music Search

Push the Control knob towards right or left.

⁄

•

All or some of the operations above cannot be

performed if the Bluetooth audio player is not ready for

remote control.

Switching between Bluetooth audio sources does

not start or stop playback automatically. Perform the

operation for starting or stopping playback.

Some audio players cannot be controlled remotely or

reconnected after Bluetooth disconnection. Operate the

main unit of the audio player to connect Bluetooth.

24 KDC-X993/ KDC-HD942U/ KDC-X693/ KDC-MP642U

Other Functions

Activating Security Code

Deactivating Security Code

To deactivate the Security Code function.

⁄

•

You can set the Security Code with a 4 digit number of your

choice.

1 Select Security code mode

Select “MENU” > “Security Clear”

For how to select Function Control items, refer to

<Function Control> (page 6).

•

The Security Code cannot be displayed or referenced. Make

a note of the Security Code and treasure it up.

1 Select Security code mode

2 Enter Security Code mode

Press the Control knob for at least 1 second.

When “Enter” is displayed, “[–][–][–][–]” is also

displayed.

Select “MENU” > “Security Set”

For how to select Function Control item, refer to

<Function Control> (page 6).

2 Enter Security Code mode

Press the Control knob for at least 1 second.

When “Enter” is displayed, “[–][–][–][–]” is also

displayed.

3 Enter Security Code

Operation type

Operation

Push the Control knob towards right

or left.

Turn the Control knob or push it

towards up or down.

Select the digits to enter

3 Enter Security Code

Select the Security Code

numbers

Operation type

Operation

Select the digits to enter

Push the Control knob towards right

or left.

Turn the Control knob or push it

towards up or down.

4 Press the Control knob for at least 3 seconds.

“Clear” is displayed.

The Security Code function deactivates.

Select the Security Code

numbers

5 Exit Security Code mode

Press the [FNC] button.

4 Confirm the Security Code

Press the Control knob for at least 3 seconds.

When “Re-Enter” is displayed, “[–][–][–][–]” is also

displayed.

5 Do the step 3 through 4 operation, and reenter

the Security Code.

“Approved” is displayed.

The Security Code function activates.

⁄

•

If you enter the wrong Code in steps 3 through 4, repeat

from step 3.

6 Exit Security Code mode

Press the [FNC] button.

Entering Security Code

The Security Code is required to use the audio unit

when the unit is first used after removed from the

battery power source or the Reset button is pressed.

1 Turn the power ON.

2 Do the step 3 through 4 operation, and enter

the Security Code.

“Approved” is displayed.

Now, you can use the unit.

English

Other Functions

Manual Clock Adjustment

Date Format Selection

1 Select Clock adjustment mode

Select “MENU” > “Clock Adjust”.

For how to select Function Control items, refer to

<Function Control> (page 6).

1 Select Date format mode

Select “MENU” > “Date Mode”.

For how to select Function Control items, refer to

<Function Control> (page 6).

2 Enter Clock adjustment mode

Press the Control knob for at least 1 second.

The clock display blinks.

2 Enter Date format mode

Press the Control knob for at least 1 second.

The date is displayed.

3 Adjusting Clock

Operation type

Selecting the item (hours or

minutes)

3 Adjusting Date

Turn the Control knob.

Select from 7 types.

Operation

Push the Control knob towards right

or left.

Turn the Control knob or push it

towards up or down.

4 Exit Date format mode

Press the [FNC] button.

Adjust each item

4 Exit Clock adjustment mode

Press the [FNC] button.

Function of KDC-X993/ KDC-X693

When LX AMP unit connecting

⁄

•

You can do this adjustment when “MENU” > “SYNC” in

AMP Control

<Function Control> (page 6) is set to “OFF”.

You can control the LX AMP connected to the unit.

1 Select AMP Control mode

Date Adjustment

Select “MENU” > “AMS Control”.

For how to select Function Control items, refer to

<Function Control> (page 6).

1 Select Date adjustment mode

Select “MENU” > “Date Adjust”.

For how to select Function Control items, refer to

<Function Control> (page 6).

2 Enter AMP Control mode

Press the Control knob for at least 1 second.

2 Enter Date adjustment mode

Press the Control knob for at least 1 second.

The date display blinks.

3 Select the AMP Control item for adjustment

Turn the Control knob or push it towards up or

down.

3 Adjusting Date

Operation type

⁄

•

For the details on the AMP Control item, see the

Instruction manual attached to the LX AMP.

Operation

Selecting the item (month, day, Push the Control knob towards right

or year)

Adjust each item

or left.

4 Adjust the AMP Control item

Push the Control knob towards right or left.

Turn the Control knob or push it

towards up or down.

5 Exit AMP Control mode

Press the [FNC] button.

4 Exit Date adjustment mode

Press the [FNC] button.

26 KDC-X993/ KDC-HD942U/ KDC-X693/ KDC-MP642U

Demonstration mode setting

Theft Deterrent Faceplate

Turning the demonstration mode ON/OFF.

The faceplate of the unit can be detached and taken

with you, helping to deter theft.

1 Select Demonstration mode

Select “MENU” > “DEMO Mode”.

For how to select Function Control items, refer to

<Function Control> (page 6).

Removing the Faceplate

1 Press the Release button.

Drop open the faceplate.

2 Set the Demonstration mode

2 Drawing the faceplate to left side pull it to

forward and remove it.

Press the Control knob for at least 2 seconds.

Pressing this button for 2 seconds or longer toggles

the setting between “ON” and “OFF”.

3 Exit Demonstration mode

Press the [FNC] button.

•

The faceplate is a precision piece of equipment and can

be damaged by shocks or jolts.

•

Keep the faceplate in its faceplate case while detached.

Do not expose the faceplate (and the faceplate case) to

direct sunlight or excessive heat or humidity. Also avoid

places with too much dust or the possibility of water

splashing.

Reattaching the Faceplate

1 Align the shaft on the unit with the depression

on the faceplate.

2 Push the faceplate in until it clicks.

The faceplate is locked in place, allowing you to use

the unit.

English

Audio Adjustments

Audio Control

Audio Setup

You can adjust following Audio Control items;

You can set Sound system , such as follows;

Adjustment Item Display

Range

0 — 35

Adjustment Item Display

Volume offset

Dual Zone System

Range

“VOL-OFFSET” –8 — 0 (AUX: -8— +8)

“2 ZONE” OFF/ON

Rear volume

Subwoofer level

Balance

“REAR VOLUME”

“SUBWOOFER LEVEL” –15 — +15

“BALANCE”

“FADER”

Left 15 — Right 15

Rear 15 — Front 15

⁄

Fader

Exit Audio Control mode (Volume control mode)

•

Volume offset: Sets each source’s volume as a difference

from the basic volume.

•

Dual Zone System

1 Enter Audio Control mode

Main source and sub source (Auxiliary input) output

Front channel and Rear channel separately.

- Set up the channel of sub source by “ZONE2” of

<Function Control> (page 6).

Press the [AUD] knob.

2 Select the Audio item to adjust

Press the [AUD] knob.

- Select Main source by [SRC] button.

- Adjust the volume of Front channel by [AUD] knob.

- Adjust the volume of Rear channel by <Audio Control>

(page 28) or [5]/[∞] button on the remote control

(page 43).

3 Adjust the Audio item

Turn the [AUD] knob.

4 Exit Audio Control mode

Press any button.

Press a button other than the [AUD] knob or [0]

button.

- The Audio Control has no effect on sub source.

1 Select the source to adjust

Press the [SRC] button.

2 Enter Audio Setup mode

Press the [AUD] knob for at least 1 second.

3 Select the Audio Setup item to adjust

Press the [AUD] knob.

4 Adjust the Audio setup item

Turn the [AUD] knob.

5 Exit Audio Setup mode

Press the [AUD] knob for at least 1 second.

28 KDC-X993/ KDC-HD942U/ KDC-X693/ KDC-MP642U

Sound Setup

For how to select Function Control item, refer to

<Function Control> (page 6).

Cabin selection

You can compensate the delay of the sound arrival

time by selecting your environment from the

following car types;

2 Select the speaker you want to set

Setting speaker

Front speaker

Rear speaker

Subwoofer

Display

“FRONT”

“REAR"

Car type

Display

“OFF”

Not compensating.

Compact car

Full size car

Station wagon

Minivan

“SUB W"

“Compact”

“Full size car”

“Wagon”

“Minivan”

“SUV”

Turn the Control knob.

3 Select the item you want to set

Sport-utility vehicle

Long Minivan

Item

Setting overview

“Minivan (Long)”

“FRONT” >“SIZE”

Speaker Size Front

>“LOCATION” Speaker Location Front

>“TWEETER” Speaker Select Tweeter

1 Enter Cabin select mode

Select “SOUND” > “Setup” > “Cabin”.

For how to select Function Control item, refer to

<Function Control> (page 6).

“REAR"

>“SIZE”

>“LOCATION” Speaker Location Rear

“SUB W" >“SIZE” Speaker Size Subwoofer

Speaker Size Rear

Push the Control knob towards up or down.

2 Select the car type

Turn the Control knob and push the center

when the desired item is displayed.

Exit Cabin select mode.

4 Set the value

Turn the Control knob.

5 Repeat steps 2 to 4 to complete the speaker

settings.

⁄

•

You can compensate the distances in more details by

using <DTA> (page 30) function.

6 Exit Speaker setting mode

Press the [FNC] button.

Speaker setting

The speaker X’Over is automatically set when the

position and size of each speaker are selected from

the following items;

Item

Range

Speaker Size Front

“O.E.M.”,“4inch”,“5inch”,“6 1/2inch”,

“6 3/4inch”,“7inch”,“4x6”,“5x7”,“6x8”,

“6x9”,“7x10”

Speaker Location Front

Speaker Size Tweeter

Speaker Size Rear

“Door”, “On Dash”, “Under Dash”

“None”, “Use”

“None”, “O.E.M.”,“4inch”,“5inch”,

“6 1/2inch”,“6 3/4inch”,“7inch”,“4x6”,

“5x7”,“6x8”,“6x9”,“7x10”

Speaker Location Rear

Speaker Size Subwoofer

“Door”, “Rear Deck”

“Minivan”, “Minivan (Long)”:

“2nd Row”, “3rd Row”

“None”, “6 1/2inch”, “8inch”, “10inch”,

“12inch”, “15inch Over”

1 Enter Speaker setting mode

Select “SOUND” > “Setup” > “Speaker”.

English

Sound Setup

DTA (Digital Time Alignment) setting

X’Over setting

Adjusting fine tuning of the speaker position

compensation value specified at <Cabin selection>

(page 29).

Fine adjusting the following setting values

corresponding to the X’Over values set in the

section <Speaker Setting> (page 29);

Adjustment Item Display

Front High Pass Filter, “FC”

Rear High Pass Filter

Range

1 Enter DTA setting mode

Through, 30*, 40, 50*, 60, 70,

80, 90*, 100, 120, 150, 180,

220, 250* (Hz)

Select “SOUND” > “Setup” > “DTA”.

For how to select Function Control item, refer to

<Function Control> (page 6).

Front High Pass Slope, “SLOPE”

Rear High Pass Slope,

Subwoofer Slope *

Subwoofer Low Pass “FC”

Filter

-6, -12, -18, -24 dB/Oct

2 Select the speaker you want to set

Setting speaker

Front speaker

Rear speaker

Subwoofer

Display

“Front”

“Rear"

“SW"

30*, 40, 50*, 60, 70, 80, 90*,

100, 120, 150, 180, 220,

250*, Through (Hz)

Subwoofer Phase

“PHASE”

Reverse (180°)/ Normal (0°)

*Function of the KDC-X993/ KDC-X693.

Turn the Control knob.

1 Enter X’Over setting mode

3 Set the compensation value of the speaker

position

Select “SOUND” > “Setup” > “X’Over”.

For how to select Function Control item, refer to

<Function Control> (page 6).

Turn the Control knob and push the center

when the desired value is displayed.

Adjust between 0 and 14.44 feet.

Refer to “DTA” of <Menu Glossary> (page 48) on

how to set the compensation value.

Exit DTA setting mode.

2 Select the speaker you want to set

Setting speaker

Front speaker

Rear speaker

Subwoofer

Display

“Front”

“Rear"

“Subwoofer"

Turn the Control knob and push the center

when the desired item is displayed.

3 Select the item you want to set

Item

Setting overview

“Front”

>“FC”

Front High Pass Filter

>“SLOPE” Front High Pass Slope

>“FC” Rear High Pass Filter

>“SLOPE” Rear High Pass Slope

“Subwoofer" >“FC” Subwoofer Low Pass Filter

“Rear"

>“SLOPE” Subwoofer Slope

>“PHASE” Subwoofer Phase

Push the Control knob towards up or down.

4 Set the X’Over value

Turn the Control knob.

5 Repeat steps 2 to 4 to complete the X’Over

setting.

6 Exit X’Over setting mode

Press the [FNC] button.

30 KDC-X993/ KDC-HD942U/ KDC-X693/ KDC-MP642U

Preset Equalizer curve select

Manual Equalizer Control

You can select following Equalizer curve;

You can adjust following Equalizer Control items;

KDC-X993/ KDC-X693

Equalizer curve

Natural

User*

Rock

Pops

Easy

Top 40

Jazz

Display

“Natural”

“User”

“Rock”

“Pops”

“Easy”

“Top 40”

“Jazz”

“Game”

“iPod”

Adjustment Item

Band 1

Band 2

Band 3

Band 4

Band 5

Band level

Bass Effect*

Display Range

“BAND1”

“BAND2”

“BAND3”

“BAND4”

“BAND5”

“GAIN”

62.5 Hz

250 Hz

1 kHz

4 kHz

16 kHz

-9 –+9 dB

“ON”/“OFF”

Game

“EFCT”

iPod (During iPod source only)

*Can be only set for “BAND1”.

* The Equalizer curve set in the section <Manual Equalizer

Control> is recalled.

KDC-HD942U/ KDC-MP642U

Adjustment Item

Band 1

Band 2

Band 3

Quality

Display Range

1 Enter Preset Equalizer mode

Select “SOUND” > “Control” > “EQ” >

“Preset Equalizer”.

For how to select Function Control item, refer to

<Function Control> (page 6).

“BAND1”

“BAND2”

“BAND3”

“Q”

60/ 100/ 160/ 250/ 400 Hz

630/ 1k/ 1.6k/ 2.5k Hz

4k/ 6.3k/ 10k/ 16k Hz

0.25/ 0.5/ 1.0/ 2.0

Band level

“GAIN”

-9 –+9 dB

2 Select the Equalizer curve

Turn the Control knob and push the center

when the desired item is displayed.

You can select from 22 Equalizer curve types for

iPod when “iPod” is selected.

Exit Preset Equalizer mode.

Select the iPod Equalizer curve

1. Enter iPod Equalizer mode

1 Enter Manual Equalizer Control mode

Select “SOUND” > “Control” > “EQ” >

“Manual Equalizer”.

For how to select Function Control item, refer to

<Function Control> (page 6).

2 Select the band you want to set

Turn the Control knob.

Press the Control button.

2. Select the iPod Equalizer curve

Turn the Control knob and push the center

when the desired item is displayed.

Exit Preset Equalizer mode.

3 Select the item you want to set

Push the Control knob towards up or down.

Move the cursor “>” to the desired item.

4 Set the value

Turn the Control knob.

⁄

•

You can select for each source.

5 Repeat steps 2 to 4 to complete the Equalizer

curve.

To change the band, move the cursor “>” to “band#”.

6 Exit Manual Equalizer Control mode

Press the [FNC] button.

⁄

•

When “iPod” is selected in the section <Preset Equalizer

curve select> (page 31), Manual Equalizer Control is

disabled.

•

You can select for each source.

English

Sound Setup

Function of KDC-X993/ KDC-X693

Preset position selection

Manual position setting

According to the listening position, select the

position from the following settings so that the

normal position of the sound environment can

be compensated in accordance with the selected

position;

Making fine adjustment of the value specified at

Preset position selection per speaker.

1 Enter Manual position setting mode

Select “SOUND” > “Control” > “Position” >

“Manual Position”.

For how to select Function Control item, refer to

<Function Control> (page 6).

Compensation seat

Not compensating.

Front-Left seat

Front-Right seat

Front seat

Range

“ALL”

“Front-Left”

“Front-Right”

“Front”

2 Select the speaker you want to set

Item

Setting overview

Front Left speaker

Front Right speaker

Rear Left speaker

Rear Right speaker

Subwoofer Left

“FRONT”/“L”

“FRONT”/“R”

“REAR”/“L”

“REAR /“R”

“SUBWOOFER”/“L”

1 Enter Preset position setting mode

Select “SOUND” > “Control” > “Position” >

“Preset Position”.

For how to select Function Control item, refer to

<Function Control> (page 6).

“SUBWOOFER”/“R” Subwoofer Right

2 Select the seat you want to compensate

Turn the Control knob.

“INITIAL”

Initialize the setting values.

Push the Control knob towards up or down.

3 Exit Preset position setting mode

Press the [FNC] button.

3 Set the value

Turn the Control knob.

Adjust between 0 and 5.58 feet.

Press the Control knob for at least 1 second if you

want to execute the “INITIAL”.

4 Exit Manual position setting mode

Press the [FNC] button.

32 KDC-X993/ KDC-HD942U/ KDC-X693/ KDC-MP642U

Audio Preset Memory

Audio Preset Recall

Registering the value setup by Sound Control.

Recalling the sound setup registered by <Audio

Preset Memory> (page 33).

1 Setup Sound Control

Refer to the following operations to setup the

Sound Control.

1 Select the source

Press the [SRC] button.

- Cabin selection (page 29)

- Speaker Setting (page 29)

2 Enter Audio preset recall mode

Select “SOUND” > “Preset” > “Recall”.

For how to select Function Control items, refer to

<Function Control> (page 6).

- DTA (Digital Time Alignment) setting (page 30)

- X’Over setting (page 30)

- Manual Equalizer Control (page 31)

- Preset position selection (page 32)

- Manual position setting (page 32)

3 Select the number to recall in the memory

Turn the Control knob and push the center

when the desired number is displayed.

2 Enter Audio preset memory mode

Select “SOUND” > “Preset” > “Memory”.

For how to select Function Control items, refer to

<Function Control> (page 6).

4 Turn the Control knob to select “YES”, and then

press the Control knob.

“Recall Completed” is displayed.

5 Exit Audio preset recall mode

3 Select the number to put in the memory

Turn the Control knob and push the center

when the desired number is displayed.

Press the [FNC] button.

⁄

4 Turn the Control knob to select “YES”, and then

press the Control knob.

•

The “User” of <Preset Equalizer curve select> (page 31) is

changed to the value which was recalled.

•

The Equalizer curve is changed to the value which was

recalled by the selected source.

“Memory Completed” is displayed.

5 Exit Audio preset memory mode

Press the [FNC] button.

⁄

•

Number “1”: When you press the Reset, all the sources

will be the setting value which is registered.

Number “1” and “2”:

The memory cannot be erased by the Reset button.

This function cannot be registered when the iPod

Equalizer set in <Preset Equalizer curve select> (page 31).

•

English

Favorite Control

Favorite Preset Memory

Favorite Preset Recall

Registering the operation procedure to select your

favorite broadcast station or iPod Playlists/ Artists,

etc.

Retrieving an item registered to Favorite.

1 Enter Favorite Preset Recall mode

Turn the Control knob.

1 Display a favorite item

2 Select the number to recall in the Favorite

memory

Turn the Control knob.

Source

Registerable items

TUNER/SIRIUS/XM/HD Preset Memory

iPod

List selection screen for Playlists/ Artists/

Albums, etc.

3 Recall the Favorite Preset

Press the Control knob.

Hands-free phone

Telephone number retrieval.

Cancelling the Favorite Preset Recall mode

Turn the Control knob to select “Return”, and

then press the Control knob.

“

”

is displayed when the operation procedure

FAV

can be registered.

iPod setting

The desired list in the first hierarchy can be registered.

⁄

1st hierarchy

PLAYLISTS

ARTISTS

2nd hierarchy

3rd hierarchy

iPod

•

When iPod is selected for the source, the list selection

screen for Playlists/ Artists/ Albums, etc. is displayed.

Songs will not be automatically played.

ALL ARTISTS

ARTISTS 1

ARTISTS 2

ARTISTS 3

ALBUMS

ALL ALBUMS

ALBUM 1

ALBUM 2

COMPOSERS

ALBUM 3

Favorite Preset Memory Delete

AUDIOBOOKS

Deleting an item registered to Favorite.

2 Enter Favorite Preset Memory mode

Press the [ ] button for at least 1 second.

1 Enter Favorite Preset Memory Delete mode

Select “MENU” > “Favorite Delete”.

For how to select Function Control item, refer to

<Function Control> (page 6).

3 Select the number to put in the memory

Turn the Control knob.

2 Enter Favorite Preset Memory Delete mode

Press the Control knob for at least 1 second.

4 Put the Favorite Preset in the memory

Press the Control knob.

3 Select the number you want to delete

Turn the Control knob and push the center

when the desired number is displayed.

“Delete?” is displayed.

Cancelling the Favorite Preset Memory mode

Press the [ ] button.

⁄

•

Registering the operation procedure to an existing

preset number overwrites the existing procedure.

Select “ALL” if you want to delete all.

4 Turn the Control knob to select “YES”, and then

press the Control knob.

“Completed” is displayed.

The memory cannot be erased by the Reset button.

The same memory storage operation can be used for

“MENU”, “SETUP”, and “SOUND” in the section <Function

Control> (page 6).

Exit Favorite Preset Memory Delete mode.

However, some currently selected sources cannot be

recalled. For information on available sources, refer to

Condition column in the section <Function Control>.

If the items in the second or lower hierarchy are

changed, the list in iPod will be changed by adding or

deleting songs after the FAVORITE registration. Due to

this, the list registered in this unit will be different from

the list in iPod. The FAVORITE registration should be

performed again after editing the items in iPod.

•

34 KDC-X993/ KDC-HD942U/ KDC-X693/ KDC-MP642U

Favorite Name Setting

Giving a name to Preset Memory registered to

Favorite.

1 Enter Preset Recall mode

Turn the Control knob.

2 Retrieve the Preset Memory to change

Turn the Control knob.

3 Enter Favorite Name set mode

Press the Control knob for at least 1 second.

Select the “FAVORITE NAME SET” display.

4 Enter the name

Operation type

Operation

Move the cursor to the enter

character position

Push the Control knob towards right

or left.

Select the character type*

Select the characters

Press the Control knob.

Turn the Control knob or push it

towards up or down.

* Each time you press the knob, the character type

alternates between the types shown in the table below.

Character type

Alphabet upper case

Alphabet lower case

Numbers and symbols

5 Exit Favorite Name Set mode

Push the Control knob towards right or left

to select “ENTER”, and then press the Control

knob.

Cancelling the Favorite Name set

Press the [FNC] button.

English

Function of KDC-X993

KDC-HD942U/ KDC-X693/ KDC-MP642U with KCA-BT200 (Optional Accessory)

Bluetooth Setup

Press the [FNC] button.

Registering Bluetooth device

To make your Bluetooth device (cell-phone) usable

with this unit, you need to register it (pairing). You

can register up to five Bluetooth devices to this unit.

⁄

•

This unit allows up to eight digits to be input for a PIN

code. If a PIN code cannot be input from this unit, it can

be input from the Bluetooth device.

•

If there are 5 or more Bluetooth devices registered, you

cannot register a new Bluetooth device.

If the error message appears even though the PIN code

is correct, try <Registering Special Bluetooth device>

(page 36).

When registering from Bluetooth devices

1 Turn on the control unit.

2 Start registering a unit by operating the

Bluetooth device

By operating the Bluetooth device, register the

hands-free unit (pairing). Select “KENWOOD BT

CD/R-2P2”/ “KENWOOD BT200” from the list of

connected units.

Registering Special Bluetooth device

Allow registration of a special device that cannot be

registered normally (pairing).

3 Enter a PIN code

Input the PIN code registered as mentioned in

<Registering PIN Code> (page 36).

Check that registration is complete on the

Bluetooth device.

1 Select Special device registration mode

Select “MENU” > “SPCL DVC Select”.

For how to select Function Control item, refer to

<Function Control> (page 6).

4 By operating the Bluetooth device, start hands-

free connection.

2 Enter Special device registration mode

Press the Control knob for at least 1 second.

A list is displayed.

When registering from this unit

1 Select Bluetooth device registration mode

Select “MENU” > “Device Regist”.

For how to select Function Control item, refer to

3 Select a device name

Turn the Control knob and push the center

when the desired device name is displayed.

If “Completed” is displayed, registration is

completed.

<Function Control> (page 6).

2 Enter Bluetooth device registration mode

Press the Control knob for at least 1 second.

Search for the Bluetooth device.

4 Go through the procedure of <Registering

Bluetooth device> (page 36) and complete the

registration (pairing).

When search is completed, “Finished” is displayed.

3 Select the Bluetooth device

Turn the Control knob and push the center

when the desired Bluetooth device is displayed.

Cancelling Special device registration mode

Press the [FNC] button for at least 1 second.

4 Input the PIN code

Operation type

⁄

•

If the device name is not in the list, select “Other Phones”.

Operation

Select the numbers.

Turn the Control knob or push it towards

up or down.

Move to the next digit.

Delete the last digit.

Push the Control knob towards right.

Push the Control knob towards left.

Registering PIN Code

By operating the Bluetooth device, specify the PIN

code necessary for registering this unit.

5 Transmit the PIN code

Press the Control knob for at least 1 second.

If “Pairing Success” is displayed, registration is

completed.

1 Select PIN code edit mode

Select “MENU” > “PIN Code Edit”.

For how to select Function Control item, refer to

<Function Control> (page 6).

6 Return to the device list

Press the Control knob.

2 Enter PIN code edit mode

7 Exit Bluetooth device registration mode

36 KDC-X993/ KDC-HD942U/ KDC-X693/ KDC-MP642U

Press the Control knob for at least 1 second.

The current setting of PIN code is displayed.

3 By operating the cell-phone, start the hands-

free connection.

3 Input the PIN code

To clear the downloading completion message

Press any button.

Operation type

Operation

Select the numbers.

Turn the Control knob or push it towards

up or down.

Push the Control knob towards right.

Push the Control knob towards left.

⁄

•

Up to 1000 phone numbers can be registered for each

registered cell-phone.

Move to the next digit.

Delete the last digit.

•

Up to 32 digits can be registered for each phone number

along with up to 50* characters representing a name.

(* 50: Number of alphabetic alphabetical characters.

Fewer characters can be input depending on the type

of characters.)

4 Register a PIN code

Press the Control knob for at least 1 second.

If “Completed” is displayed, registration is

completed.

•

To cancel downloading of the phone book data, operate

the cell-phone.

5 Exit PIN code edit mode

Press the [FNC] button.

⁄

Selecting the Bluetooth device You

Wish to Connect

•

By default, “0000” is specified.

A PIN code can be specified with up to eight digits.

When two or more Bluetooth devices have already

been registered, you need to select the Bluetooth

device you wish to use.

Downloading the Phone Book

1 Select Bluetooth device selection mode

Cell-phone

Select “MENU” > “Phone Selection”.

Download the phone book data from the cell-

phone to this unit so that you can use the Phone

Book of this unit.

Audio player

Select “MENU” > “Audio Selection”.

For how to select Function Control item, refer to

<Function Control> (page 6).

To download automatically

If the cell-phone supports a phone book

synchronization function, the phone book is

downloaded automatically after Bluetooth

connection.

2 Enter Bluetooth device selection mode

Press the Control knob for at least 1 second.

“(name)” is displayed.

⁄

•

Setting on the cell-phone may be required.

If no phone book data is found in the unit even after

the compete display, your cell-phone may not support

automatic download of phone book data. In this case, try

downloading manually.

3 Select the Bluetooth device

Turn the Control knob.

4 Set up the Bluetooth device

Push the Control knob towards right or left.

‘✱(name)’ or ‘-(name)’ is displayed.

“✱”: The selected Bluetooth device is busy.

“-”: The selected Bluetooth device is on standby.

“ “ (blank): The Bluetooth device is deselected.

To download from the cell-phone manually

1 By operating the cell-phone, end the hands-free

connection.

2 By operating the cell-phone, send the phone

book data to this unit

By operating the cell-phone, download the phone

book data to this unit.

• During downloading:

“Downloading” is displayed.

5 Exit Bluetooth device selection mode

Press the [FNC] button.

⁄

•

If a cell-phone is already selected, deselect it, and then

select a different one.

•

If you cannot select a device using the audio player,

connect the device with the audio player.

• After completion of downloading:

“Completed” is displayed.

English

Function of KDC-X993

KDC-HD942U/ KDC-X693/ KDC-MP642U with KCA-BT200 (Optional Accessory)

Bluetooth Setup

Deleting a Registered Bluetooth

device

Adding a voice dialing command

Add a voice tag to the phonebook for voice dialing.

You can register up to 35 voice tags.

You can delete a registered Bluetooth device.

1 Select Phonebook name edit mode

Select “BT” > “Voice Tag” > “PB Name Edit”.

For how to select Function Control item, refer to

<Function Control> (page 6).

1 Select Bluetooth device deletion mode

Select “MENU” > “Device Delete”.

For how to select Function Control item, refer to

<Function Control> (page 6).

2 Enter Phonebook name edit mode

2 Enter Bluetooth device deletion mode

Press the Control knob for at least 1 second.

“(name)” is displayed.

Press the Control knob.

3 Search for the name to register

Select the name to register with reference to 4 in

<Calling a number in the Phone Book> (page 22).

If a voice tag has already been registered for a

name, “*” is displayed before the name.

3 Select the Bluetooth device

Turn the Control knob.

4 Delete the selected Bluetooth device

Press the Control knob.

4 Select a mode

Turn the Control knob.

5 Turn the Control knob to select “YES”, and then

press the Control knob.

“Delete” is displayed.

Display

Operation

“PB Name Regist”

“PB Name Check”*

“PB Name Delete”*

“Return”

Play a voice tag.

Delete a voice tag.

Return to step 2.

6 Exit Bluetooth device deletion mode

Press the [FNC] button.

⁄

•

When a registered cell-phone is deleted, its Phone Book,

log, SMS, and voice tag are also deleted.

* Displayed only when a name for which a voice tag has

been registered is selected.

Select “PB Name Regist” (Regist)

5 Register a voice tag (first)

Press the Control knob.

Displaying the Firmware Version

“Enter Voice 1” is displayed.

When a beep is heard, utter a voice tag within 2

seconds.

Display the version of the firmware of this unit.

1 Enter Bluetooth Firmware update mode

Select “MENU” > “BT F/W Update”.

For how to select Function Control item, refer to

6 Confirm the voice tag (second)

Press the Control knob.

“Enter Voice 2” is displayed.

<Function Control> (page 6).

2 Enter Bluetooth Firmware update mode

Press the Control knob for at least 1 second.

The firmware version appears.

When a beep is heard, utter the same voice tag as

that you uttered in step 4 within 2 seconds.

“Completed” is displayed.

3 Exit Bluetooth Firmware update mode

7 End registration

Press the [FNC] button.

Press the Control knob.

Return to step 2. You can register another voice tag

continuously.

⁄

•

For how to update the firmware, access our web site.

⁄

http://www.kenwood.com/bt/information/

•

If your voice cannot be recognized, a message is

displayed. Pressing the [AUD] knob allows you to retry

voice input. (page 54)

Select “PB Name Check” (Play)

5 Press the Control knob.

Play the registered voice and return to step 2.

38 KDC-X993/ KDC-HD942U/ KDC-X693/ KDC-MP642U

Select “PB Name Delete” (Delete)

Setting a Voice Command for

Category

5 Delete a voice tag

Press the Control knob.

Add a voice tag to the phone number category

(type) for voice calling.

6 Turn the Control knob to select “YES”, and then

press the Control knob.

1 Select Phone Number type edit mode

Select “BT” > “Voice Tag” > “PN Type Edit”.

For how to select Function Control item, refer to

<Function Control> (page 6).

Exit Phonebook name edit mode

Press the [FNC] button.

⁄

•

Audio sound is not output during voice tag registration.

2 Enter Phone Number type edit mode

Press the Control knob.

3 Select the category (type) you wish to set

Turn the Control knob and push the center

when the desired category name is displayed.

“General”/ “Home”/ “Office”/ “Mobile”/ “Other”

4 Select a mode

Turn the Control knob.

Display

Operation

“PN Type Regist”

“PN Type Check”*

“PN Type Delete”*

“Return”

Play a voice tag.

Delete a voice tag.

Return to step 2.

* Displayed only when a name for which a voice tag has

been registered is selected.

5 Register the category (type) by performing

steps 5 to 7 in <Adding a voice dialing

command> (page 38).

6 Exit Phone Number type edit mode

Press the [FNC] button.

⁄

•

Set the voice tag for all the 5 categories. If the voice tag

is not registered for all the categories, the Phonebook

may not be recalled by voice command.

English

Function of KDC-X993

KDC-HD942U/ KDC-X693/ KDC-MP642U with KCA-BT200 (Optional Accessory)

Bluetooth Setup

SMS (Short Message Service)

Downloading the SMS

The SMS arrived at the cell-phone is displayed on

the receiver.

Download the short message (SMS) arrived at the

cell-phone so that it can be read on this unit.

A newly arrived message is displayed.

1 Select SMS download mode

Select “BT” > “SMS” > “SMS Download”.

For how to select Function Control item, refer to

<Function Control> (page 6).

•

To prevent car accidents, the driver should not read the

SMS while driving.

When a new message arrives

“SMS Received” is displayed.

The display disappears with any operations.

2 Enter SMS download mode

Press the Control knob.

A message list appears.

Displaying the SMS

3 Start downloading

Press the Control knob.

1 Select SMS Inbox mode

“SMS Downloading” is displayed.

When the downloading finishes, “Completed” is

displayed.

Select “BT” > “SMS” > “SMS Inbox”.

For how to select Function Control item, refer to

<Function Control> (page 6).

4 Exit SMS download mode

2 Enter SMS Inbox mode

Press the Control knob.

A message list appears.

Press the [FNC] button.

⁄

•

The cell-phone must be able to transmit the SMS using

Bluetooth. Setting on the cell-phone may be required.

If the cell-phone does not support SMS function, the

SMS download item in Function Control mode is not

displayed.

3 Select a message

Turn the Control knob.

Each pushing of the Control knob towards right or

left switches between telephone number or name

and message reception date.

•

When the SMS is downloaded from the cell-phone, the

unopened messages in the cell-phone are opened.

The already-read and unread short messages can be

respectively downloaded up to 75.

4 Display the text

Press the Control knob.

Turning the Control knob scrolls the message.

Pressing the Control knob again returns to the

message list screen.

5 Exit SMS Inbox mode

Press the [FNC] button.

⁄

•

The unopened message is displayed at the beginning

of the list. Other messages are displayed in the order of

reception.

The SMS that has arrived when the cell-phone is not

linked with Bluetooth cannot be displayed. Download

the SMS.

The short message cannot be displayed during

downloading the SMS.

40 KDC-X993/ KDC-HD942U/ KDC-X693/ KDC-MP642U

Satellite Radio tuner (Optional Accessory) control

Basic Operation

Preset Memory

Putting the channel in the memory.

Selecting Satellite Radio source

Press the [SRC] button.

Select the “SAT”/ “SIRIUS”/ “XM” display.

1 Select the channel to put in the memory

Push the Control knob towards right or left.

⁄

2 Enter Preset Memory mode

•

You need to register to the service provider to receive

the service by Satellite Radio. Consult the service

provider if “CALL … TO SUBSCRIBE” appears.

The radio may take a little time to start receiving after

you select the Satellite Radio source.

Press the [ ] button.

3 Select the number to put in the memory

Turn the Control knob.

•

4 Determine the number to put in the memory

Press the Control knob for at least 1 second.

If the signal reception fails, “Acquiring Aignal”/ “No Signal”

appears.

Cancelling the Preset Memory mode

Press the [ ] button twice.

Switching Seek Mode

KDC-X993:

Press the [AUTO] button for at least 1 second.

KDC-HD942U/ KDC-X693/ KDC-MP642U:

Press the [AUTO] button.

⁄

•

Only the channel number is stored. Category information

is not stored.

Display

Operation

“CHANNEL”

“PRESET”

Normal manual seeking control.

Search in order of the channels in the Preset memory.

Preset Tuning

Select the channel

Push the Control knob towards right or left.

Recalling the channels in the memory.

1 Enter Preset Tuning Select mode

Selecting the Preset Band

Press the [ ] button.

Push the Control knob toward up.

Each time you push the knob, the preset band

alternates between the SR1, SR2, SR3 and SR4.

2 Select a desired station in the memory

Turn the Control knob.

3 Recall the station

Push the Control knob.

Category and Channel Search

Cancelling Preset Tuning

Press the [ ] button twice.

Selecting the channel and category you want to

receive.

1 Enter Category and Channel Search mode

Press the [ ] button twice.

2 Select the Category

Turn the Control knob to select Category, and

then press the Control knob.

3 Select the Channel

Turn the Control knob to select Channel, and

then press the Control knob.

Cancelling Category and Channel Search mode

Press the [ ] button.

⁄

•

You cannot Channel search until the category

information is acquired.

English

Satellite Radio tuner (Optional Accessory) control

Channel Scan

Every receivable Channel is checked for 10 seconds.

1 Start Channel Scan

Select “Channel Scan”.

For how to select Function Control items, refer to

<Function Control> (page 6).

2 Release it when the channel you want to listen

to is received

Press the Control knob.

Function of remote control

Direct Access Tuning

Entering the channel and tuning.

1 Enter Direct Access Tuning mode

Press the [DIRECT] button on the remote

control.

2 Enter the channel

Press the number buttons.

3 Do Channel Search

Press the [4] or [¢] button.

Cancelling Direct Access Tuning

Press the [DIRECT] button on the remote

control.

⁄

•

If you make no button operation for 10 seconds, the

Direct Access Tuning mode is automatically canceled.

If you cannot receive any signal in the input Channel due

to bad conditions on radio wave or other such problems,

“ACQUIRING SIGNAL”/ “NO SIGNAL” appears.

•

42 KDC-X993/ KDC-HD942U/ KDC-X693/ KDC-MP642U

Basic Operations of remote control

In Tuner/HD Radio source

SRC

VOL

SRC

Band select [FM]/[AM]

ATT

Station select [4]/[¢]

Recall preset stations [1] — [6]

AT T

VOL

AUD

FM/AM

In CD/USB source

DIRECT

(page 15, 16, 19)

Music select [4]/[¢]

Folder/Disc select [FM]/[AM]

Pause/Play [38]

2-ZONE

0 — 9

In Satellite Radio tuner source

Preset band select [FM]

Channel select [4]/[¢]

Recall preset channels [1] — [6]

General control

Volume control [VOL]

Source select [SRC]

Volume reduce [ATT]

When the button is pressed again, the volume returns

to the previous level.

In Audio control

Audio item select [AUD]

Adjust the Audio item [VOL]

⁄

•

Refer to <Audio Control> (page 28) for the operation

method, such as the procedures for Audio control and

others operations.

Dual Zone control

Dual zone system on and off [2-ZONE]

Rear channel volume control [ 5]/ [∞]

English

Basic Operations of remote control

Loading and Replacing battery

Use two “AA”/ “R6”-size batteries.

Hands-free phone control

Slide the cover while pressing downwards to remove

it as illustrated.

Insert the batteries with the + and – poles aligned

properly, following the illustration inside the case.

Making a call

Enter the dialing method selection mode

Select a dialing method [38]

Number dial input

[

]

Operation type

Input a digit.

Input“+”.

Input“#”.

Input“*”.

Operation

[0] – [9] buttons

[¢] button

[FM] button

[AM] button

[4] button

Clear the entered phone number.

Make a call [DIRECT]

Receiving a call

Answer the call

[

]

Switch between the private talk mode and the

hands-free talk mode [38]

Call waiting

Answer Another Incoming Call with the Current

Call Suspended

[

]

Answer another Incoming Call after Terminating

the Current Call [SRC]

Continue the Current Call [1]

During a call

End the call [SRC]

Adjust the voice volume [VOL]

¤ CAUTION

•

Do not leave the battery near fire or under direct

sunlight. A fire, explosion or excessive heat

generation may result.

• Do not set the remote control in hot places such

as on the dashboard.

44 KDC-X993/ KDC-HD942U/ KDC-X693/ KDC-MP642U

Appendix

About Audio file

iPod/iPhone that can be connected to this

unit

Made for

• iPod nano (1st generation) • iPod nano (2nd generation)

• iPod nano (3rd generation) • iPod nano (4th generation)

•

Playable Audio file

AAC-LC (.m4a), MP3 (.mp3), WMA (.wma)

Playable disc media

CD-R/RW/ROM

Playable disc file format

• iPod with video

• iPod classic

• iPod touch (1st generation) • iPod touch (2nd generation)

Works with

ISO 9660 Level 1/2, Joliet, Romeo, Long file name.

Playable USB device

USB mass storage class

Playable USB device file system

FAT16, FAT32

• iPhone

• iPhone 3G

•

Although the audio files are complied with the

standards listed above, the play maybe impossible

depending on the types or conditions of media or

device.

• Update iPod/iPhone software to the latest version.

• The word “iPod” appearing in this manual indicates

the iPod or the iPhone connected with the iPod

connection cable* (optional accessory).

* Not supported model KCA-iP500.

Refer to the web site for connectable iPod and iPod

connection cable.

•

Playing order of the Audio file

In the example of folder/file tree shown below, the

files are played in the order from ① to ⑩.

FFoollddeerr

AAuuddiioofﬁile

(ꢂ)

vꢀ

ꢁ

www.kenwood.com/ipod/kca_ip/

⁄

ꢃ

vꢆ

vꢇ

• If you start playback after connecting the iPod, the

music that has been played by the iPod is played

first.

ꢅ

vꢄ

ꢈ

In this case, “RESUMING” is displayed without

displaying a folder name, etc. Changing the browse

item will display a correct title, etc.

• You cannot operate iPod if “KENWOOD” or “✓”

displayed on iPod.

vꢉ

An online manual about audio files is put on the

site, www.kenwood.com/audiofile/. On this online

manual, detailed information and notes which are not

written in this manual are provided. Make sure to read

through the online manual as well.

About USB device

• When the USB device is connected to this unit,

it can be charged up provided that this unit is

powered.

⁄

•

In this manual, the word “USB device” is used for flash

memories and digital audio players which have USB

terminals.

• Install the USB device in the place where it will not

prevent you from driving your vehicle properly.

• You cannot connect a USB device via a USB hub and

Multi Card Reader.

• Take backups of the audio files used with this unit.

The files can be erased depending on the operating

conditions of the USB device.

We shall have no compensation for any damage

arising out of erasure of the stored data.

• No USB device comes with this unit. You need to

purchase a commercially available USB device.

• When connecting the USB device, usage of the

CA-U1EX (option) is recommended.

Normal playback is not guaranteed when a cable

other than the USB compatible cable is used.

Connecting a cable whose total length is longer

than 5 m can result in abnormal playback.

English

Appendix

About Satellite Radio tuner (Optional)

This unit supports Satellite Radio tuners which are

released by SIRIUS and XM.

For operating KCA-BT100 (Optional)

The following control methods of the function

for this unit may be different from the Instruction

manual; therefore, refer to the following supplemental

instruction.

Refer to the instruction manual of Satellite radio tuner.

1. Press the Control knob. Select the display other

than “INITIAL”.

About HD Radio (Optional)

When you connect an HD Radio, Tuner features of

the unit are disabled and changed to HD Radio tuner

features.

2. Press the [ ] button.

3. Select the number to recall by turning the Control

knob.

With the HD Radio tuner, you can use the similar

functions of Tuner features. Refer to Tuner features for

how to use the functions.

4. Press the Control knob.

1. Operation is the same. Refer to the instruction

manual of KCA-BT100.

For operating KCA-BT200 (Optional)

For operation refer to Model-B-2 in the Instruction

Manual of KCA-BT200, and the table below.

2. Press the [ ] button.

3. Select the number to memory by turning the

Control knob.

4. Press the Control knob for at least 1 seconds.

Refer to <Deleting a Registered Bluetooth device>

(page 38) in this instruction manual.

Notation used in the KCA-BT200 Operation

Instruction Manual

[38] button

Control knob

Press the Control knob for at least

1 second.

Press the [AUTO]/[TI] button.

For how to operate Menu, refer to <Function

Control> in this instruction manual.

About display

Cell-Phone Status is displayed in the status display of

this unit.

Moreover, some displays are different from the

description of KCA-BT100 Instruction Manual.

Displays of KCA-BT100 Instruction Actual displays on this unit

Manual

“DISCONCT”

“CONNECT”

“PHN-DEL”

“P-STATUS”

“HF Disconnect”

“HF Connect”

“Device Delete”

“BT DVC Status”

46 KDC-X993/ KDC-HD942U/ KDC-X693/ KDC-MP642U

About the Cell-Phone

This unit conforms to the following Bluetooth

specifications:

Version

Profile

Bluetooth Standard Ver. 1.2

HFP (Hands Free Profile)

OPP (Object Push Profile)

PBAP (Phonebook Access Profile)

SYNC (Synchronization Profile)

For the cell-phones verified for compatibility, access

the following URL:

http://www.kenwood.com/bt/information/

⁄

•

The units supporting the Bluetooth function have been

certified for conformity with the Bluetooth Standard

following the procedure prescribed by Bluetooth

SIG. However, it may be impossible for such units to

communicate with your cell-phone depending on its type.

HFP is a profile used to make a hands-free call.

OPP is a profile used to transfer data such as a phone book

between units.

•

About the Bluetooth Audio player

This unit conforms to the following Bluetooth

specifications:

Version

Profile

Bluetooth Standard Ver. 1.2

A2DP (Advanced Audio Distribution Profile)

AVRCP (Audio/Video Remote Control Profile)

⁄

•

A2DP is a profile designed to transfer the music from an

audio player.

•

AVRCP is a profile designed to control playback and

selection of music by an audio player.

About KENWOOD “Music Editor” of PC

application

• “Music Editor” is recorded in the CD-ROM attached

to this unit.

• Refer to the user’s manual recorded in the

installation CD-ROM and Help of “Music Editor” for

the operation method of “Music Editor”.

• The unit can play USB device created by “Music

Editor”.

• Information about “Music Editor” upgrade is put on

the site, www.kenwood.com.

English

Appendix

•

DISP N/P

Menu Glossary

Switches the panel display between positive

or negative. In addition, you can reverse it in

conjunction with the interior light.

•

AMP

Selecting “OFF” turns off the built-in amplifier.

Turning off the built-in amplifier improves the

quality of the sound from Preout.

Auto Answer (Setting the Time Interval for

Automatic Answer)

POSI1 : Displays the text in the positive.

•

POSI2 : When the interior light is off, the text is

displayed in the positive; when the interior

light is on, the text is displayed in the

negative.

This function automatically answers (responds

to) a call after lapse of the preset time interval for

automatic answer.

“OFF” : Does not answer the phone call

automatically.

“0” : Automatically answers the phone call at once.

“1s” – “99s” : Automatically answers the phone call

after lapse of 1 – 99 seconds.

NEGA1 : Displays the text in the negative.

NEGA2 : When the interior light is off, the text

is displayed in the negative; when the

interior light is on, the text is displayed in

the positive.

•

DTA (Digital Time Alignment)

Make fine adjustment of the delay time of the

speaker output specified at <Cabin selection>

(page 29) to have a more suitable environment for

your vehicle.

The settings of the delay time are automatically

identified and compensated by specifying the

distances of each speaker from the center of the

vehicle interior.

1 Set the front and rear positions and the height

of the reference point to the position of the ears

of the person sitting in the front seat, and set

the right and left positions to the center of the

vehicle interior.

2 Measure the distances from the reference point

to the speakers.

⁄

•

If the time set in the cell-phone is shorter than that set in

the unit, the former will be used.

•

This function does not work for call waiting.

•

Call Beep (Setting the Beep of the Incoming Call)

You can output a beep from the speaker when a

call comes in.

“ON” : Beep is heard.

“OFF” : Beep is canceled.

CD Read

Sets the method for reading CD.

When unable to play special format CD, set this

function to “2” to force playing. Note that some

music CD may be unplayable even when set to “2”.

In addition, audio files cannot be played when set

to “2”. Normally, keep this set to “1”.

3 Calculate the distance difference in accordance

with the farthest speaker.

1 : Automatically distinguishes between audio file

disc and music CD when playing disc.

2 : Forces playing as music CD.

•

Display

+3.2 feet

If this unit is not operated at least 5 seconds with

“OFF” selected, the display turns off. During a setup

mode, the display will not turn off even if 5 seconds

lapse.

DISP DIM (Display illumination dimmer)

Reduces the display Illumination brightness.

AUTO: Dims the illumination in conjunction with

the Light switch of the vehicle.

FRONT

1.7 feet

2.6 feet

REAR

+2.3 feet

REAR

4.9 feet

MNAL1: Dims the illumination constantly.

MNAL2: Dims the illumination darker than MNA1.

OFF: Does not dim the illumination.

+0 feet

SUB-W

48 KDC-X993/ KDC-HD942U/ KDC-X693/ KDC-MP642U

•

BT DVC Status (Displaying the Bluetooth device

Status)

•

SP Select (Setting up the Voice Output

Speakers)

You can display the connection status, signal

strength, and battery level.

You can specify the voice output speakers.

“FRONT” : Outputs voice from the front-left and

front-right speakers.

: Battery level of cell-phone.

Full

Nearly dead

Minimum

“F-R” : Outputs voice from the front-right speaker.

“F-L” : Outputs voice from the front-left speaker.

: Signal strength of cell-phone.

Maximum

⁄

•

Select the speaker which is further from the microphone

in order to prevent howling or echoes.

•

Icons are not displayed if information cannot be

obtained from the cell-phone.

Since the number of steps of the control unit is different

from that of the cell-phone, the statuses displayed on

the control unit may discord from those displayed on

the cell-phone.

•

Supreme+ (Supreme Plus)

•

Technology to extrapolate and supplement with

proprietary algorithm, the high-frequency range

that is cut off when encoding.

The bass and vocal sound that are cut off by

encoding are supplemented for the reproduction

of natural sound quality.

Supplementing is optimized by compression

format (AAC, MP3 or WMA) and processed

according to bit rate.

The effect is negligible with music that is encoded

at high bit rate, variable bit rate or has minimal high

frequency range.

•

HIGHWAY-SOUND

Increases the volume of faintest sound being lost

by road noises to make the sound more audible.

Additionally, it accentuates bass sound being

lost by road noises to make the bass sound more

dynamic.

Illumi DIM (Key illumination dimmer)

Reduces the key Illumination brightness.

AUTO: Dims the illumination in conjunction with

the Light switch of the vehicle.

The bass and vocal sound of Music CD/ iPod is also

supplemented.

MNAL1: Dims the illumination constantly.

MNAL2: Dims the illumination darker than MNA1.

OFF: Does not dim the illumination.

•

ZONE2 (Dual Zone)

Set the destination (front speaker “FRONT” or rear

speaker “REAR”) of the sub source (AUX IN) when

the Dual Zone function is turned on.

•

Mic Gain

Adjusts the sensitivity of the built-in microphone

for a telephone call. Adjust the voice of caller.

Setting to “+” increases the voice volume.

NR Level

Reduces the noises generated by surrounding

environment without changing the built-in

microphone volume. Adjust the voice of caller

when it is not clear. Setting to “+” increases the

noise reduction.

•

Receive Mode (Receive mode Setting)

Sets the receive mode of the HD Radio.

Auto: Automatically tunes to analog broadcast

when there is no digital broadcast.

Digital: Digital broadcasts only.

Analog: Analog broadcasts only.

English

Accessories/ Installation Procedure

the ignition wires to a power source that can be turned on

and off with the ignition key. If you connect the ignition

wire to a power source with a constant voltage supply, as

with battery wires, the battery may die.

If the console has a lid, make sure to install the unit so that

the faceplate will not hit the lid when closing and opening.

If the fuse blows, first make sure the wires aren’t touching

to cause a short circuit, then replace the old fuse with one

with the same rating.

Insulate unconnected wires with vinyl tape or other similar

material. To prevent a short circuit, do not remove the caps

on the ends of the unconnected wires or the terminals.

Connect the speaker wires correctly to the terminals to

which they correspond. The unit may be damaged or fail to

work if you share the - wires or ground them to any metal

part in the car.

When only two speakers are being connected to the

system, connect the connectors either to both the front

output terminals or to both the rear output terminals (do

not mix front and rear). For example, if you connect the +

connector of the left speaker to a front output terminal, do

not connect the - connector to a rear output terminal.

After the unit is installed, check whether the brake lamps,

blinkers, wipers, etc. on the car are working properly.

Mount the unit so that the mounting angle is 30° or less.

Reception may drop if there are metal objects near the

Bluetooth antenna.

Accessories

•

..........1

..........2

..........4

•

3 m (9.5 ft) ..........1

*Accessory of KDC-X993

•

Installation Procedure

1. To prevent a short circuit, remove the key from the

ignition and disconnect the - battery.

2. Make the proper input and output wire

connections for each unit.

3. Connect the speaker wires of the wiring harness.

•

4. Connect the wiring harness wires in the following

order: ground, battery, ignition.

5. Connect the wiring harness connector to the unit.

6. Install the unit in your car.

7. Reconnect the - battery.

8. Press the reset button.

Bluetooth antenna unit

About CD players/disc changers connected

to this unit

If the CD player/ disc changer has the “O-N” switch, set

it to the “N” position.

The functions you can use and the information that

can be displayed may differ depending on the models

being connected.

2WARNING

If you connect the ignition wire (red) and the battery wire

(yellow) to the car chassis (ground), you may cause a short

circuit, that in turn may start a fire. Always connect those

wires to the power source running through the fuse box.

•

Mounting and wiring this product requires skills and

experience. For safety’s sake, leave the mounting and wiring

work to professionals.

For Good Reception

To assure good reception, note the following:

• Communicate with the cell-phone within the line-

of-sight distance of 10 m (30 ft). The communication

range becomes shorter depending on the

surrounding environment. The communication

range also becomes shorter when there is an

obstacle between this unit and the cell-phone. The

above maximum communication range (10 m) is

not always assured.

•

Make sure to ground the unit to a negative 12V DC power

supply.

Do not install the unit in a spot exposed to direct sunlight

or excessive heat or humidity. Also avoid places with too

much dust or the possibility of water splashing.

Do not use your own screws. Use only the screws provided.

If you use the wrong screws, you could damage the unit.

If the power is not turned ON (“PROTECT” is displayed),

the speaker wire may have a short-circuit or touched the

chassis of the vehicle and the protection function may

have been activated. Therefore, the speaker wire should be

checked.

•

• A broadcast station or walkie-talkie located nearby

can interfere with communication due to too strong

signal.

•

If your car’s ignition does not have an ACC position, connect

50 KDC-X993/ KDC-HD942U/ KDC-X693/ KDC-MP642U

Connecting Wires to Terminals

To USB device

USB connector (1m)

Steering remote control

Do not remove the cap when you do

not use the USB cable. The connector

will cause the unit to malfunction if it

gets in touch with any metallic part of

the vehicle.

(Light Blue/Yellow)

Rear output

⁄

Front output

REMO.CONT

Sub Woofer output

To use the steering wheel

remote control feature, you

need to an exclusive remote

adapter (not supplied)

matches your car is required.

Microphone input

(KDC-X993 only)

Microphone

(Accessory5)

FM/AM antenna input

AUX input (Stereo)

Use the mini-plug which is stereo type

and does not have any resistance.

Fuse (10A)

Wiring harness

(Accessory1)

To Kenwood disc changer/ External optional accessory

To connect these leads, refer to the relevant

⁄

instruction manuals.

White

White/Black

To front left speaker

Gray

Gray/Black

To front right speaker

To rear left speaker

To rear right speaker

Green

Green/Black

Purple

Purple/Black

If no connections are made, do not let the wire come out from the tab.

Power control wire (Blue/White)

Motor antenna control wire (Blue)

When using the optional power amplifier, connect to its power control

terminal.

P.CONT

Depending on what antenna you are using, connect either to the control

terminal of the motor antenna, or to the power terminal for the booster

amplifier of the film-type or short pole type antenna.

ANT.

CONT

TEL mute wire (Brown)

Connect to the terminal that is grounded when either the telephone

rings or during conversation.

MUTE

To connect the Kenwood navigation system, consult your

⁄

navigation manual.

Dimmer control wire (Orange / White)

To car light control switch

ILLUMI

Car fuse

box

Ignition key

switch

Ignition wire (Red)

ACC

Car fuse box

(Main fuse)

Battery wire (Yellow)

Ground wire (Black) · (To car chassis)

–

Battery

English

Installation/Removing the Unit

non-Japanese cars

Removing the hard rubber frame

1 Engage the catch pins on the removal tool and

remove the two locks on the upper level.

Upper the frame and pull it forward as shown in

the figure.

Lock

Catch

Bend the tabs of the mounting

sleeve with a screwdriver or similar

utensil and attach it in place.

Accessory2

⁄

Removal tool

•

Make sure that the unit is installed securely in place. If the

unit is unstable, it may malfunction (for example, the sound

may skip).

2 When the upper level is removed, remove the

lower two locations.

⁄

Japanese cars

•

The frame can be removed from the bottom side in the

same manner.

1 Refer to the section <Removing the hard rubber

frame> and then remove the hard rubber frame.

Removing the Unit

2 Align the holes in the unit (two locations on each

side) with the vehicle mounting bracket and secure

the unit with the accessory screws.

1 Refer to the section <Removing the hard rubber

frame> and then remove the hard rubber frame.

2 Insert the two removal tools deeply into the slots

on each side, as shown.

T/N

3 Lower the removal tool toward the bottom, and

pull out the unit halfway while pressing towards

the inside.

T: Toyota cars

N: Nissan cars

Accessory2

8 mm

MAX.

8mm

MAX.

ø5mm

Accessory3...for Nissan car

Accessory4...for Toyota car

•

Be careful to avoid injury from the catch pins on the

removal tool.

4 Pull the unit all the way out with your hands, being

¤ CAUTION

careful not to drop it.

Install this unit in the console of your vehicle.

Do not touch the metal part of this unit during and

shortly after the use of the unit. Metal part such as

the heat sink and enclosure become hot.

52 KDC-X993/ KDC-HD942U/ KDC-X693/ KDC-MP642U

Accessory of KDC-X993

Installation the Microphone Unit

1 Check the installation position of the microphone

(accessory 5).

2 Remove oil and other dirt from the installation

surface.

3 Install the microphone.

4 Wire the microphone cable up to the hands-free

box with it secured at several positions using tape

or the like.

Accessory5

Fix a cable with a commercial

item of tape.

Peel the release coated paper of double-face adhesive tape to

fix on the place shown above.

Adjust the direction of the microphone to the driver.

⁄

•

Install the microphone as far as possible from the cell-

phone.

English

Troubleshooting Guide

Some functions of this unit may be disabled by

some settings made on this unit.

What might seem to be a malfunction in your unit

may just be the result of slight misoperation or

miswiring. Before calling service, first check the

following table for possible problems.

• Cannot set up the subwoofer.

• No output from the subwoofer.

• Cannot set up the subwoofer position of Manual

position setting.

General

? The Touch Sensor Tone does not sound.

• <Subwoofer output> of <Basic Operation> (page 4)

is not set to On.

• The Dual zone function is enabled. ☞ <Audio

Setup> (page 28)

✔

The preout jack is being used.

☞

The Touch Sensor Tone cannot be output from

the preout jack.

Tuner source

• Cannot set up the subwoofer phase.

The Low Pass Filter is set to Through. ☞ <X’Over

setting> (page 30)

? Radio reception is poor.

✔

The car antenna is not extended.

☞

Pull the antenna out all the way.

• Cannot select the output destination of the

subsource in the Dual zone.

• Cannot adjust the volume of the rear speakers.

The Dual zone function is disabled. ☞ <Audio

Setup> (page 28)

Disc source

? The specified disc does not play, but another one

plays instead.

✔

The specified CD is quite dirty.

☞

Clean the CD, referring to the CD cleaning of the

section on <Handling CDs> (page 3).

• Cannot register a security code.

• Cannot set up Display.

<Demonstration mode Setting> (page 27) is not

The disc is loaded in a different slot from that

specified.

turned off.

☞

Eject the disc magazine and check the number

for the specified disc.

✔

The disc is severely scratched.

Try another disc instead.

☞

Audio file source

? The sound skips when an Audio file is being

played.

✔

The media is scratched or dirty.

☞

Clean the media, referring to the CD cleaning of

the section on <Handling CDs> (page 3).

The recording condition is bad.

Record the media again or use another media.

☞

54 KDC-X993/ KDC-HD942U/ KDC-X693/ KDC-MP642U

Hands-free

The messages shown below display your

systems condition.

? The hands-free talk volume is low.

✔

The hands-free talk volume is set at a low level.

TOC Error:

• No disc has been loaded in the disc

magazine.

☞

The hands-free talk volume can be adjusted

independently. Adjust it during hands-free talk.

“MENU” > “Mic Gain” and “NR Level” <Function

Control> (page6).

• The CD is quite dirty. The CD is upside-

down. The CD is scratched a lot.

ERROR 05:

ERROR 77:

The disc is unreadable.

? No sound is heard from the rear speakers.

You are talking in the hand-free talk mode.

The unit is malfunctioning for some reason.

➪ Press the reset button on the unit. If the

“ERROR 77” code does not disappear,

consult your nearest service center.

✔

☞

No sound is heard from the rear speakers in the

hands-free talk mode.

? No beep is heard at reception of an incoming call.

ERROR 99:

Something is wrong with the disc magazine.

Or the unit is malfunctioning for some reason.

➪ Check the disc magazine. And then press

the reset button on the unit. If the “ERROR

99” code does not disappear, consult your

nearest service center.

✔

No beep is heard depending on the type of your

cell-phone.

☞

The “MENU” > “Call Beep” of <Function Control>

(page 6) is set ON.

? Voice is not recognized.

✔

The vehicle window is open.

CD-IN (Blink): The CD player section is not operating

properly.

☞

If the surrounding noise is large, voice cannot be

recognized properly. Close the vehicle windows

to reduce noise.

➪ Reinsert the CD. If the CD cannot be

ejected or the display continues to flash

even when the CD has been properly

reinserted, please switch off the power

and consult your nearest service center.

Small voice.

If voice is too small, it cannot be recognized

☞

properly. Speak into the microphone a little more

loudly and naturally.

The person uttering the voice tag is not the one who

registered the it.

Protect (Blink): The speaker wire has a short-circuit or

touches the chassis of the vehicle, and then

the protection function is activated.

☞

Only the voice of the person who registered the

voice tag can be recognized.

➪ Wire or insulate the speaker cable properly

and press the reset button. If the “Protect”

code does not disappear, consult your

nearest service center.

Bluetooth audio source

? The Bluetooth audio player cannot be registered

Unsupported File:

(pairing).

An Audio file is played with a format that this

unit can’t support.

✔

The PIN code is fixed.

☞

When a PIN code is specified in the Instruction

Manual for Bluetooth Audio Player, register it

with reference to <Registering PIN Code> (page

36) to register the Bluetooth audio player. If no

PIN code is specified in the Instruction Manual,

try “0000”.

Copy Protection:

A copy-protected file is played.

Read Error:

The file system of the connected USB device

is broken.

➪ Copy the files and folders for the USB

device again. If the error message is still

displayed, initialize the USB device or use

other USB devices.

? The sound from the Bluetooth audio player is

discontinuous.

✔

The distance between this unit and audio player is

too far.

No Device:

N/A Device:

The USB device is selected as a source

although no USB device is connected.

➪ Change the source to any source other

than USB. Connect an USB device, and

change the source to USB again.

☞

Move the audio player nearer to this unit.

✔

Another Bluetooth device is affecting the Bluetooth

communication.

☞

Turn off another Bluetooth device.

Move another Bluetooth device away from this

unit.

• An unsupported USB device is connected.

• Connection to the iPod has failed.

➪ Check that the connected iPod is an iPod

that is supported. See <About Audio file>

(page 45) for information on supported

iPods.

✔

Another Bluetooth device or profile is used for

communication.

☞

The downloading of the Phone book or the SMS

disconnects the sound.

English

Troubleshooting Guide

No Music Data/Error 15:

Too Long:

The word or utterance is too long to be

recognized.

• The connected USB device contains no

playable audio file.

• Media was played that does not have data

recorded that the unit can play.

No Phonebook: Data is not contained in the phone book.

No Message: No short message in In Box.

USB ERROR:

iPod Error:

Some trouble may have occurred to the

connected USB device.

➪ Remove the USB device, then cycle the

power switch to ON. If the same display is

repeated, use another USB device.

No Record:

The voice tag is not registered in the

phonebook.

Memory Full: The number of voice tags reaches the

maximum number to be registered in the

phonebook.

Connection to the iPod has failed.

➪ Remove the USB device and then

reconnect it.

➪ Confirm that the software for the iPod is

the latest version.

Favorite: No Memory:

The procedure is not registered to Favorite

Preset Memory

No Access:

The procedure preset with Favorite Control

cannot be available. The preset content may

not be recalled depending on the selected

source or mode.

USB REMOVE (Blink):

The Remove mode has been selected for the

USB device/iPod. You can remove the USB

device/iPod safely.

No Voice:

No call.

NO Number: • The calling party does not notify a caller ID.

• There is no phone number data.

HD Memory Full:

The tag memory of HD Radio is FULL.

No Data:

• There is no outgoing call list.

• There is no incoming call list.

• There is no missed call list.

• There is no phone book list.

iPod Memory Full:

The iPod memory is FULL.

No Tag Function:

iPod which does not support the tag memory

is connected.

No Entry:

The cell-phone has not been registered

(pairing).

N/A Channels: No receivable channel and category.

HF Disconnect: The unit cannot communicate with the cell-

phone.

HF Error 07:

The memory cannot be accessed.

➪ Turn off the power and on again. If this

message still appears, press the reset

button on the control unit.

HF Error 68:

The unit cannot communicate with the cell-

phone.

➪ Turn off the power and on again. If this

message still appears, press the reset

button on the control unit.

Un Known:

Device Full:

The Bluetooth device cannot be detected.

5 Bluetooth device have already been

registered. No more Bluetooth device cannot

be registered.

PIN Code NG: The PIN code is wrong.

Connect NG: The unit cannot be connected to the device.

Pairing Failed: Pairing error.

Err No Matching:

The voice tag is wrong. Voice cannot be

recognized because of an unregistered voice

tag, etc.

Too Soft:

Voice is too small and cannot be recognized.

Voice is too large to be recognized.

Too Loud:

56 KDC-X993/ KDC-HD942U/ KDC-X693/ KDC-MP642U

Specifications

FM tuner section

Bluetooth section (KDC-X993)

Frequency range (200 kHz space)

: 87.9 MHz – 107.9 MHz

Version

: Bluetooth Ver. 1.2 Certified

Usable sensitivity (S/N = 30dB)

: 9.3dBf (0.8 μV/75 Ω)

Frequency range

: 2.402 – 2.480 GHz

Quieting Sensitivity (S/N = 50dB)

: 15.2dBf (1.6 μV/75 Ω)

Output Power

: +4dBm (MAX), 0dBm (AVE) Power Class 2

Frequency response ( 3 dB)

: 30 Hz – 15 kHz

Maximum Communication range

: Line of sight approx.10m (32.8 ft)

Signal to Noise ratio (MONO)

: 70 dB

Profiles

: HFP (Hands Free Profile)

Selectivity ( 400 kHz)

: HSP (Headset Profile)

: SPP (Serial Port Profile)

: PBAP (Phonebook Access Profile)

: OPP (Object Push Profile)

: ≥ 80 dB

Stereo separation (1 kHz)

: 40 dB

: SYNC (Synchronization Profile)

: A2DP (Advanced Audio Distribution Profile)

: AVRCP (Audio/Video Remote Control Profile)

Digital FM tuner section (KDC-HD942U)

Frequency range (200 kHz space)

: 87.5 MHz – 107.9 MHz

Frequency response

CD player section

Laser diode

: GaAlAs

Digital filter (D/A)

: 8 Times Over Sampling

D/A Converter

: 24 Bit

Spindle speed

: 500 – 200 rpm (CLV)

: 20 Hz – 20 kHz

Signal to Noise ratio (STEREO)

: 70 dB

AM tuner section

Frequency range (10 kHz space)

: 530 kHz – 1700 kHz

Usable sensitivity (S/N = 20dB)

: 28 dBμ (25 μV)

Wow & Flutter

: Below Measurable Limit

Frequency response ( 1 dB)

Digital AM tuner section (KDC-HD942U)

Frequency range (10 kHz space)

: 530 kHz – 1700 kHz

Frequency response

: 40 Hz – 15 kHz

: 10 Hz – 20 kHz

Total harmonic distortion (1 kHz)

KDC-X993/KDC-X693: 0.008 %

KDC-HD942U/KDC-MP642U: 0.010 %

Signal to Noise ratio (1 kHz)

KDC-X993/KDC-X693: 110 dB

Signal to Noise ratio (STEREO)

: 70 dB

KDC-HD942U/KDC-MP642U: 105 dB

Dynamic range

: 93 dB

MP3 decode

: Compliant with MPEG-1/2 Audio Layer-3

WMA decode

: Compliant with Windows Media Audio

AAC decode

: AAC-LC ".m4a" files

Specifications subject to change without notice.

English

Specifications

USB Interface

Auxiliary input

USB Standard

: USB1.1/ 2.0 (Full speed)

Frequency response ( 1 dB)

: 20 Hz – 20 kHz

File System

: FAT16/ 32

Input Maximum Voltage

: 1200 mV

MP3 decode

: Compliant with MPEG-1/2 Audio Layer-3

Input Impedance

: 10 kΩ

WMA decode

: Compliant with Windows Media Audio

AAC decode

: AAC-LC ".m4a" files

General

Operating voltage (10.5 – 16V allowable)

: 14.4 V

Maximum Current consumption

: 10 A

Audio section

Maximum output power

: 50 W x 4

Full Bandwidth Power (at less than 1% THD)

: 22 W x 4

Installation Size (W x H x D)

: 182 x 53 x 158 mm

7-3/16 x 2-1/16 x 6-1/4 inch

Weight

: 3.08 lbs (1.4 kg)

Speaker Impedance

: 4 – 8 Ω

Tone action (KDC-X493, KDC-MP442U)

BAND1 (60 Hz): 9 dB

BAND2 (250 Hz): 9 dB

BAND3 (1 kHz): 9 dB

BAND4 (4 kHz): 9 dB

BAND5 (16 kHz): 9 dB

Tone action (KDC-HD942U/KDC-MP642U)

BAND1 : 60 Hz - 400 Hz 9 dB

BAND2 : 630 Hz - 2.5 kHz 9 dB

BAND3 : 4.0 kHz - 16 kHz 9 dB

Preout level / Load (CD)

KDC-X993/KDC-X693/KDC-HD942U

: 4000 mV/10 kΩ

KDC-MP642U: 2500 mV/10 kΩ

Preout impedance

: ≤ 600 Ω

Specifications subject to change without notice.

58 KDC-X993/ KDC-HD942U/ KDC-X693/ KDC-MP642U

IC (Industry Canada) Notice

Operation is subject to the following two conditions:

(1) This device may not cause interference, and

(2) this device must accept any interference, including

interference that may cause undesired operation

of the device.

The term “IC: ” before the certification/registration

number only signifies that the Industry Canada

technical specification were met.

2CAUTION

Use of controls or adjustments or performance of

procedures other than those specified herein may

result in hazardous radiation exposure.

In compliance with Federal Regulations, following

are reproductions of labels on, or inside the product

relating to laser product safety.

Kenwood Corporation

2967-3, ISHIKAWA-MACHI,

HACHIOJI-SHI

TOKYO, JAPAN

KENWOOD CORP. CERTIFIES THIS EQUIPMENT

CONFORMS TO DHHS REGULATIONS N0.21 CFR

1040. 10, CHAPTER 1, SUBCHAPTER J.

Location : Bottom Panel

FCC WARNING

This equipment may generate or use radio

frequency energy. Changes or modifications to this

equipment may cause harmful interference unless

the modifications are expressly approved in the

instruction manual. The user could lose the authority

to operate this equipment if an unauthorized change

or modification is made.

FCC NOTE

This equipment has been tested and found to

comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against

harmful interference in a residential installation. This

equipment may cause harmful interference to radio

communications, if it is not installed and used in

accordance with the instructions. However, there

is no guarantee that interference will not occur in a

particular installation. If this equipment does cause

harmful interference to radio or television reception,

which can be determined by turning the equipment

off and on, the user is encouraged to try to correct

the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment

and receiver.

• Connect the equipment into an outlet on a

circuit different from that to which the receiver is

connected.

•

The “AAC” logo is trademark of Dolby Laboratories.

The Bluetooth word mark and logos are owned by

the Bluetooth SIG, Inc. and any use of such marks

by Kenwood Corporation is under license. Other

trademarks and trade names are those of their

respective owners.

•

iTunes is a trademark of Apple Inc.

iPod is a trademark of Apple Inc., registered in the U.S.

and other countries.

•

iPhone is a trademark of Apple Inc.

“Made for iPod” means that an electronic accessory

has been designed to connect specifically to iPod and

has been certified by the developer to meet Apple

performance standards.

• Consult the dealer or an experienced radio/TV

technician for help.

•

“Works with iPhone” means that an electronic

accessory has been designed to connect specifically

to iPhone and has been certified by the developer to

meet Apple performance standards.

•

Contains Transmitter Module

FCC ID : RKXCK5050

Apple is not responsible for the operation of this

device or its compliance with safety and regulatory

standards.

Contains Transmitter Module

IC : 5119A-CK5050

English

PYLE Audio View Series PL7DHRG User Manual
Philips AJ 3800 User Manual
Panasonic KX BP800 User Manual
Panasonic AW LZ14ST55 User Manual
Ovideon LCS3730 User Manual
Marantz 541110333221M User Manual
Leica APO TELYT R User Manual
KitchenAid KUWS24RSBS01 User Manual
KitchenAid KFP715BW2 User Manual
Kenwood KTC HR300 User Manual