Kenwood KTC 1000R User Manual

KTC-1000R  
HIDEAWAY TUNER AMPLIFIER  
INSTRUCTION MANUAL  
B64-1449-00 (E) (DT) ‘99/6  
Installation  
Accessories  
External view  
External view  
......... Number of items  
External view  
......... Number of items  
......... Number of items  
1
4
7
2
5
8
3
6
.........2  
.........4  
.........1  
.........1  
.........4  
.........1  
.........2  
.........1  
2CAUTION  
The use of any accessories except for those provided might result in damage to the unit. Make  
sure only to use the accessories shipped with the unit, as shown above.  
Installation Procedure  
1. To prevent short circuits, remove the key  
from the ignition and disconnect the -  
terminal of the battery.  
• If the fuse blows, first make sure that the  
cables have not caused a short circuit, then  
replace the old fuse with one with the same  
rating.  
• Do not let unconnected cables or terminals  
touch metal on the car or anything else  
conducting electricity. To prevent short  
circuits do not remove the caps from unused  
terminals or from the ends of the  
unconnected cables.  
• Connect the speaker cables correctly to the  
terminals to which they correspond. The unit  
may receive damage or fail to work if you  
share the - cables and/or ground them to  
any metal part in the car.  
• After the unit is installed, check whether the  
brake lamps, blinkers, wipers, etc. on the car  
are working properly.  
• Insulate unconnected cables with vinyl tape  
or other similar material.  
• During use, the surface temperature of this  
unit will become high, therefore it should not  
be mounted where anything sensitive to the  
heat, such as people or resins, would come  
into contact with it.  
2. Make the proper input and output cable  
connections for each unit.  
3. Connect the speaker cables of the wiring  
harness.  
4. Take Connector B on the wiring harness and  
connect it to the speaker connector in your  
vehicle.  
5. Take Connector A on the wiring harness and  
connect it to the external power connector on  
your vehicle.  
6. Install the unit in your car.  
7. Reconnect the - terminal of the battery.  
8. Press the reset button.  
2CAUTION  
• If your car is not prepared for this special  
connection-system, consult your KENWOOD  
dealer.  
• Only use antenna conversion adapters (ISO-  
JASO) when the antenna cord has an ISO  
plug.  
• Make sure that all cable connections are  
securely made by inserting jacks until they  
lock completely.  
• If your vehicle's ignition does not have an  
ACC position, or if the ignition cable is  
connected to a power source with constant  
voltage such as a battery cable, the power  
will not be linked with the ignition (i.e., it will  
not turn on and off along with the ignition). If  
you want to link the unit's power with the  
ignition, connect the ignition cable to a  
power source that can be turned on and off  
with the ignition key.  
• Do not install the unit under the carpet.  
Otherwise heat build-up occurs and the unit  
may be damaged.  
• Install this unit in a location which allows  
heat to easily dissipate.  
Once installed, do not place any object on  
top of the unit.  
• Install the unit securely in a location that  
does not interfere with driving.  
English 3  
Installation  
Connecting Cables to Terminals  
2WARNING  
If you connect the ignition cable (red) and the battery cable (yellow) to the car chassis (ground), you  
may cause a short circuit, that in turn may start a fire. Always connect those cables to the power  
source running through the fuse box.  
Front left output (White)  
NOTE  
PREOUT  
REAR/NON-FAD  
FRONT  
Do not put anything into the fuse holder.  
TO MZ-BUS  
TO 5L I/F  
Rear left output (White) /  
Non-fading left output (White)  
FM•AM TUNER 44W×4 AMPLIFIER  
HIDEAWAY UNIT  
KTC-1000R  
Rear right output (Red) /  
Non-fading right output (Red)  
FM ANTENNA  
TV MONITOR  
FRONT SPEAKER  
REAR SPEAKER  
SUB WOOFER  
CHANGER  
DAB  
SLAVE UNIT  
Front right output (Red)  
ANTENNA INPUT  
PREOUT  
POWER  
REAR/NON-FAD  
FRONT  
FM/AM antenna input  
Antenna Conversion  
Adaptor (ISO–JASO)  
Antenna Cord (Accessory6)  
(5.5m)  
(Accessory8)  
NOTE  
Route wiring away from power  
circuitry to avoid noise.  
Antenna Cord  
(ISO)  
Wiring harness (5.5m) (Accessory5)  
Connector A  
Connector B  
8
7
6
5
4
3
2
1
Automatic illumination control cable (Orange)  
ILLUMI  
8
7
6
5
4
3
2
1
Fuse  
(3A)  
Ignition cable (Red)+12V  
ACC  
ACC  
ACC  
Connect to control unit  
power supply terminal.  
Fuse  
(10A)  
Battery cable (Yellow)+12V  
BATT  
BATT  
BATT  
Power control cable (Blue/ White)  
When using the optional power amplifier, connect to  
its power control terminal.  
P.CONT  
TEL mute cable (Brown)  
TEL MUTE  
Connect to the terminal that is grounded when either  
the telephone rings or during conversation.  
Ground cable (Black) -  
(To car chassis)  
NOTE  
To connect the KENWOOD navigation system,  
consult your navigation manual.  
If no connections are  
made, do not let the cable  
come out from the tab.  
4 English  
2WARNING  
Connector Function Guide  
Connecting the ISO Connector  
The pin arrangement for the ISO connectors  
depends on the type of vehicle you drive. Make  
sure to make the proper connections to  
prevent damage to the unit.  
The default connection for the wiring harness  
is described in 1 below. If the ISO connector  
pins are set as described in 2 or 3, make the  
connection as illustrated.  
Pin Numbers for  
Cable Colour  
Functions  
ISO Connectors  
External Power  
Connector  
A–4  
A–5  
A–6  
A–7  
Yellow  
Battery  
Power Control  
Dimmer  
Blue/White  
Orange  
Red  
Ignition (ACC)  
1 (Default setting) The A-7 pin (red) of the  
vehicle's ISO connector is linked with the  
ignition, and the A-4 pin (yellow) is  
Speaker  
Connector  
connected to the constant power supply.  
B–1  
B–2  
B–3  
B–4  
B–5  
B–6  
B–7  
B–8  
Rear Right (+)  
Rear Right ()  
Front Right (+)  
Front Right ()  
Front Left (+)  
Front Left ()  
Rear Left (+)  
Rear Left ()  
Purple  
Purple/Black  
Gray  
Gray/Black  
White  
White/Black  
Green  
A–7 Pin (Red)  
Vehicle  
Ignition cable (Red)  
ACC  
ACC  
Unit  
BATT  
BATT  
A–4 Pin (Yellow)  
Control  
unit  
ACC  
BATT  
Battery cable (Yellow)  
Green/Black  
2 The A-7 pin (red) of the vehicle's ISO  
connector is connected to the constant  
power supply, and the A-4 pin (yellow) is  
linked to the ignition.  
A–7 Pin (Red)  
Ignition cable (Red)  
ACC  
ACC  
Vehicle  
Unit  
BATT  
BATT  
ACC  
Control  
unit  
A–4 Pin (Yellow)  
BATT  
Battery cable (Yellow)  
3 The A-7 pin (red) of the vehicle's ISO  
connector is not connected to anything,  
whilst the A-4 pin (yellow) is connected to  
the constant power supply (or both the A-7  
(red) and A-4 (yellow) pins are connected to  
the constant power supply).  
Connect to a power source  
Ignition cable  
(Red)  
that can be turned on and  
|
off with the ignition key.  
Unit  
BATT  
BATT  
Vehicle  
A–4 Pin (Yellow)  
Control  
unit  
BATT  
Battery cable (Yellow)  
English 5  
Installation  
When the control unit is the KVC-1000  
Control unit (optional) KVC-1000  
DAB control cable  
(Provided with the KTC-959DAB)  
M
4
DAB tuner (optional)  
KTC-959DAB  
NAV  
IN OUT  
I
/
F
KTC-1000R  
O R N  
F
T
R E A R / N O N - F  
D A P R E O U T  
W E  
P
R
O
A N T E N N A I N P U T  
2WARNING  
V E  
U
S
N L A  
T
B
D A  
C H A N G E R  
O O F E R S U B  
W
Extention cable  
R
O
M O N I T  
R E A R S P E A K E R  
O N  
F
T
R
S P E A K E R  
F M A N T E N N A  
Changer control cable  
(Black)  
(5.5 m)  
K T C - 1 0 0 0 R  
W N I T H I D E A  
4 I W F I E R  
Y A  
U
(Accessory7)  
4 × A M P  
4
L
F M • A M T U N E R  
S U  
M
O
Z
T - B  
5 O L T I / F  
O
-
N
]"N"  
O
N
R
KMD-D400  
24BIT RESOLUTION  
D/A CONVERTER  
MENU  
DISP  
Changer control cable  
(Provided with the C907)  
DASC  
2WARNING  
11BAND  
500  
750  
1k  
2k  
4k  
8k  
16k  
SPECTRUM ANALYZER  
Only connect black cable to  
TO 5L interface. Connection  
of light-brown connecting  
cable (for NAV interface  
use) can result in failure.  
CD/MD changer (optional)  
CD player (optional)  
KDC-CPS82, KDC-C712,  
KDC-C662, KMD-D400,  
KDC-D300, etc.  
CD auto changer (optional) C907  
When the control unit is the VZ907  
NOTE  
Some model cannot be connected and certain features are unavailable. For details, see  
IMPORTANT INFORMATION (see page 2).  
2CAUTION  
Control unit (optional) VZ907  
M-S switch setting  
T O M X - B U S  
S
M
N A V . I F  
T O M O N I T O R U N I T  
Set the M-S switch to "S".  
O R N  
F
T
R E A R / N O N - F  
D A P R E O U T  
W E  
P
R
O
A N T E N N A I N P U T  
V
S
L I 
T
B
D A  
C H A N G E R  
O O F E R S U B  
W
R
O
M O N I
R E A R S P E A K E R  
O N  
F
T
R
S P E A K E R  
F M A N T E N N A  
2WARNING  
gS h  
S
K T C - 1 0 0 0 R  
W N I T H I D E A  
4 I W F I E R  
Y A  
U
M
4 × A M P  
4
L
F M • A M T U N E R  
S U  
M
O
Z
T - B  
5 O L T I / F  
KTC-1000R  
Extention cable (5.5 m) (Accessory7)  
Changer control cable (Black)  
Changer control cable  
(Provided with the C907)  
]"N"  
O
-
N
CD/MD changer (optional)  
CD player (optional)  
KDC-CPS82, KDC-C712, KDC-C662,  
KMD-D400, KDC-D300, etc.  
CD auto changer (optional) C907  
6 English  
When two CD/MD changers are interconnected  
The disk changers are distinguished by source select disk-changer 1 and disk-changer 2.  
NOTE  
If the relevant connected device has a PROTOCOL SWITCH or O-N SWITCH, be sure to set the  
switch to “N.  
NOTE  
Example 1  
Do not connect the C907 and KDC-CPS81 at the same time. The equipment  
will cease functioning.  
TO 5L I/F  
TO MZ-BUS  
TO 5L I/F  
TO MZ-BUS  
O
-
N
]"N"  
O
N
FM•AM TUNER 44W×4 AMPLIFIER  
HIDEAWAY UNIT  
KTC-1000R  
R
KMD-D400  
IT RESOLUTION  
CONVERTER  
MENU  
DISP  
FM ANTENNA  
TV MONITOR  
FRONT SPEAKER  
REAR SPEAKER  
DASC  
11BAND  
500  
750  
1k  
2k  
4k  
8k  
16k  
SPECTRUM ANALYZER  
SUB WOOFER  
CHANGER  
changer1: C907  
changer2: KDC-CPS82, KDC-C712,  
KDC-C662, KMD-D400,  
etc.  
DAB  
SLAVE UNIT  
ANTENNA INPUT  
PREOUT  
POWER  
REAR/NON-FAD  
FRONT  
KTC-1000R  
Example 2  
TO 5L I/F  
O
-
N
TO 5L I/F  
TO MZ-BUS  
]"N"  
O
N
FM•AM TUNER 44W×4 AMPLIFIER  
HIDEAWAY UNIT  
KTC-1000R  
R
KMD-D400  
4BIT RESOLUTION  
A CONVERTER  
MENU  
DISP  
FM ANTENNA  
TV MONITOR  
FRONT SPEAKER  
DASC  
11BAND  
REAR SPEAKER  
500  
750  
1k  
2k  
4k  
8k  
16k  
SPECTRUM ANALYZER  
O
-
N
SUB WOOFER  
]"N"  
changer2: KDC-C712, KDC-C662,  
CHANGER  
DAB  
SLAVE UNIT  
KMD-D400, etc.  
changer1: KDC-CPS82  
ANTENNA INPUT  
PREOUT  
POWER  
REAR/NON-FAD  
FRONT  
KDC-CPS81  
KTC-1000R  
Example 3  
R
KMD-D400  
24BIT RESOLUTION  
D/A CONVERTER  
MENU  
DISP  
changer2  
changer1  
TO 5L I/F  
DASC  
11BAND  
500  
750  
1k  
2k  
4k  
8k  
1k  
SPECTRUM ANALYZER  
TO 5L I/F  
TO MZ-BUS  
O
N
]"N"  
OFF ON  
AUX  
PROTOCOL  
SWITCH  
FM•AM TUNER 44W×4 AMPLIFIER  
HIDEAWAY UNIT  
O
O
N
KTC-1000R  
-
N
PROTOCOL  
SWITCH  
AUX  
IN  
SWITCH  
]"N"  
N
O
FM ANTENNA  
TV MONITOR  
FRONT SPEAKER  
REAR SPEAKER  
R
KMD-D400  
RESOLUTION  
CONVERTER  
MENU  
DISP  
SUB WOOFER  
TO  
CONTROLLER  
TO  
H/U  
TO  
TO  
CHANGER  
CHANGER  
1
2
DASC  
CHANGER  
11BAND  
DAB  
SLAVE UNIT  
500  
750  
1k  
2k  
4k  
8k  
16k  
SPECTRUM ANALYZER  
ANTENNA INPUT  
PREOUT  
POWER  
REAR/NON-FAD  
FRONT  
KCA-S210A  
KDC-CPS82, KDC-C712, KDC-C662,  
KMD-D400, etc.  
KTC-1000R  
NOTE  
Example 4  
If the control unit is KVC-1000, it is not possible to interconnect two C907  
units.  
TO MZ-BUS  
TO 5L I/F  
TO MZ-BUS  
FM•AM TUNER 44W×4 AMPLIFIER  
HIDEAWAY UNIT  
KTC-1000R  
FM ANTENNA  
TV MONITOR  
FRONT SPEAKER  
REAR SPEAKER  
SUB WOOFER  
1
-
2
1
-
2
]"2"  
"1"}  
CHANGER  
DAB  
SLAVE UNIT  
ANTENNA INPUT  
PREOUT  
POWER  
REAR/NON-FAD  
FRONT  
changer1: C907  
changer2: C907  
KTC-1000R  
English 7  
Installation  
Installation for Hideaway unit  
Securing to audio board  
1
2
Attach the installation brackets to the sides  
of the hideaway unit using the sems bolts  
(M4 × 8 mm).  
Use the tapping screw (ø4 × 16 mm) to  
secure the hideaway unit to the audio  
board.  
Tapping screw  
(ø4 × 16 mm)  
Installation brackets  
(Accessory3)  
(Accessory1)  
Sems bolts  
(M4 × 8 mm)  
(Accessory2)  
Securing to pile carpet  
Peel the protective strips off of the velcro  
strips, attach them to the bottom of the  
hideaway unit, and secure to the pile carpet.  
Velcro strips  
(Accessory4)  
2CAUTION  
Please do not install the unit near the  
dashboard, the rear tray, or other important  
components. Doing so could lead to injury or  
accident should the unit come off due to a shock  
and strike a person or an important component.  
Tapping screws should be used for mounting.  
(Attachment with velcro strips, although easy,  
can come off with a shock.)  
Troubleshooting Guide  
What might appear to be a malfunction in your unit may just be the result of  
slight misoperation or miswiring. Before calling service, first check the following  
table for possible problems.  
PROBLEM  
POSSIBLE CAUSE  
SOLUTION  
The power does not turn on.  
The fuse has blown.  
After checking for short circuits in the  
cables, replace the fuse with one  
having the same rating.  
No sound can be heard, or  
the volume is low.  
• The Attenuator function is turned  
on.  
• The fader and/or balance settings  
are set all the way to one side.  
• The input/output cables or wiring  
harness are connected incorrectly.  
Turn off the Attenuator function.  
• Reset the fader and/or balance  
settings.  
• Reconnect the input/output cables  
and/or the wiring harness correctly.  
See the section on "Connecting  
Cables to Terminals".  
Nothing happens when the  
buttons are pressed.  
The computer chip in the unit is not  
functioning normally.  
Press the reset button on the unit  
8 English  
Troubleshooting Guide  
PROBLEM  
POSSIBLE CAUSE  
SOLUTION  
The sound quality is poor or  
distorted.  
• A speaker cable may be pinched by  
a screw in the car.  
• The speakers are not cabled  
correctly.  
• Check the speaker wiring..  
• Reconnect the speaker cables so  
that each output terminal is  
connected to a different speaker.  
Radio reception is poor.  
• The car antenna is not extended.  
• The antenna control cable is not  
connected.  
• Pull out the antenna all the way.  
• Connect the cable correctly,  
referring to the section on  
"Connecting Cables to Terminals".  
• Adverse effect of noise from power • Be sure to install the antenna cable  
cable, etc.  
away from the power cable.  
The memory is erased when  
the ignition is turned off.  
• The battery cable has not been  
connected to the proper terminal.  
• Connect the cable correctly,  
referring to the section on  
"Connecting Cables to Terminals".  
• Connect the cable correctly,  
referring to the section on  
• The ignition and battery cable are  
incorrectly connected.  
"Connecting Cables to Terminals".  
The following indications are used to inform you that there is a problem with the connections  
of the system.  
BUS-E01: The M-S switch of the Monitor connected to the BUS terminal is set to "M".  
] Switch the Monitor’s M-S switch to "S".  
The "MASTER SW" cable of the monitor power supply harness is connected to -.  
] Do not connect the "MASTER SW" cable.  
BUS-E50: Two or more center units are connected.  
BUS-W02: The No. switch of the connected disc changers is set to the same number (1 or 2) for  
both units.  
] Set the No. switch of one disc changer to "1" and the other unit to "2" to enable proper  
use.  
BUS-W08: Two or more Monitors are connected to the BUS terminal.  
Specifications  
Specifications subject to change without notice.  
FM tuner section  
Audio section  
Frequency range (50 kHz Space)  
Maximum output power ..............................44 W × 4  
Output power (DIN 45324, +B=14.4 V) ......28 W × 4  
Tone action  
..............................................87.5 MHz – 108.0 MHz  
Usable sensitivity (S/N = 26dB) ..............0.7 µV/75  
Quieting Sensitivity (S/N = 46dB)............1.6 µV/75 Ω  
Frequency response ( 3.0 dB) ..........30 Hz – 15 kHz  
Signal to Noise ratio (MONO) ..........................65 dB  
Selectivity (DIN) ( 400 kHz) ........................ 80 dB  
Stereo separation (1 kHz) ................................35 dB  
Bass: ......................................100 Hz 10 dB  
Treble:......................................10 kHz 10 dB  
Preout level / load ..........4 V / 10 k(During CD play)  
Preout Impedance ..........................................80 Ω  
General  
MW tuner section  
Operating voltage............14.4 V (11 – 16 V allowable)  
Current consumption ................10 A at Rated power  
Installation size (W × H × D)........213 × 40 × 148 mm  
Weight ..............................................................990 g  
Frequency range (9 kHz Space)  
..................................................531 kHz – 1611 kHz  
Usable sensitivity (S/N = 20dB) ........................25 µV  
LW tuner section  
Frequency range ..........................153 kHz – 281 kHz  
Usable sensitivity (S/N = 20dB) ........................45 µV  
English 9  

PYLE Audio PLAM1200 User Manual
Planar Systems Car Video System PT1745RPF User Manual
Perlick 66134 2 User Manual
Pentax Camera Accessories 110 User Manual
Ovideon LCS3240 User Manual
Olympus MACRO ED50MM F20 User Manual
KitchenAid KFP750WH1 User Manual
KitchenAid KFP720BU0 User Manual
JVC KS R600 User Manual
JVC KS FX384 User Manual