Kenwood KRC 33R User Manual

CASSETTE RECEIVER

KRC-478R

KRC-478RV

KRC-378R

KRC-33R

INSTRUCTION MANUAL

B64-1531-00 (EY)

Safety precautions

IMPORTANT INFORMATION

2WARNING

2CAUTION

You cannot connect the unit directly to the

following CD automatic changers. For users

who want to use older changers with the

unit, follow the directions below according to

the type of changer you own:

To prevent injury and/or fire, take the

following precautions:

• Insert the unit all the way until it is fully

locked in place. Otherwise it may fly out of

place during collisions and other jolts.

To prevent damage to the machine,

take the following precautions:

• Make sure to ground the unit to a negative

12V DC power supply.

• KDC-C200 / KDC-C300 / KDC-C400

• Do not open the top or bottom covers of the

unit.

• Do not install the unit in a spot exposed to

direct sunlight or excessive heat or humidity.

Also avoid places with too much dust or the

possibility of water splashing.

• Do not set the removed faceplate or the

faceplate case in areas exposed to direct

sunlight, excessive heat or humidity. Also

avoid places with too much dust or the

possibility of water splashing.

• To prevent deterioration, do not touch the

terminals of the unit or faceplate with your

fingers.

• Do not subject the faceplate to excessive

shock, as it is a piece of precision equipment.

• When replacing a fuse, only use a new one

with the prescribed rating. Using a fuse with

the wrong rating may cause your unit to

malfunction.

• To prevent short circuits when replacing a

fuse, first disconnect the wiring harness.

• Do not place any object between the

faceplate and the unit.

Use the extension cable and the control box

attached to the CD changer, and the optional

CA-DS100 converter cable.

• KDC-C301 / KDC-C600 / KDC-C800 / KDC-

C601 / KDC-C401

Use the extension cable attached to the CD

changer, and the optional CA-DS100

converter cable.

• KDC-C100 / KDC-C302 / C205 / C705 /

non-Kenwood CD changers

• When extending the ignition, battery or

ground cables, make sure to use automotive-

grade cables or other cables with an area of

0.75mm (AWG18) or more to prevent cable

deterioration and damage to the cable

coating.

• To prevent short circuits, never put or leave

any metallic objects (e.g., coins or metal

tools) inside the unit.

• If the unit starts to emit smoke or strange

smells, turn off the power immediately and

consult your Kenwood dealer.

• Make sure not to get your fingers caught

between the faceplate and the unit.

• Be careful not to drop the unit or subject it to

strong shock.

The unit may break or crack because it

contains glass parts.

• Do not touch the liquid crystal fluid if the LCD

is damaged or broken due to shock. The

liquid crystal fluid may be dangerous to your

health or even fatal.

If the liquid crystal fluid from the LCD

contacts your body or clothing, wash it off

with soap immediately.

Cannot be used with this model.

2CAUTION

You can damage both your unit and

the CD changer if you connect them

incorrectly.

• During installation, do not use any screws

except for the ones provided. The use of

improper screws might result in damage to

the main unit.

— 3 —

Safety precautions

Cleaning the Faceplate Terminals

If the terminals on the unit or faceplate get

dirty, wipe them with a dry, soft cloth.

Cleaning the Tape Head

NOTE

After you have used the tape player many

times over a long period, magnetic powder

from the tapes and dust accumulates on the

tape head, causing noise and a deterioration

in sound quality. Clean the tape head using a

cleaning tape or cleaning kit designed for use

in car audio systems.

• If you experience problems during

installation, consult your Kenwood dealer.

• If the unit does not seem to be working right,

try pressing the reset button first. If that does

not solve the problem, consult your Kenwood

dealer.

Egnlish

Cleaning the Unit

If the front panel gets dirty, turn off the

power and wipe the panel with a dry silicon

cloth or soft cloth.

EJECT

SRC

2CAUTION

PWR

OFF

Handling Cassette Tapes

PTY

DISC

• Do not play a cassette whose tape has gone

slack. In such a case, wind it tight using a

pencil or the like in one of the spools. Playing

slack cassette tapes can result in the tape

tangling around the capstan and/or pinch

rollers, causing trouble.

Do not wipe the panel with a stiff cloth or a

cloth dampened by volatile solvents such as

paint thinner and alcohol. They can scratch

the surface of the panel and/or cause the

indicator letters to peel off.

LOUD

SCAN

B.S/RDM

REP

D.SCN

M.RDM

DISC

CLK

VOL ADJ NAME.S

Reset button

• Do not play a deformed cassette or one

whose label is starting to come off, as it can

cause the unit to malfunction.

• Do not leave tapes in hot places, such as

above the fascia panel (dashboard) and other

spots exposed to direct sunlight, or near

heater outlets. They can deform the cassette.

• Avoid using extremely long cassette tapes,

such as 100-minute-long tapes. Such tapes

are very thin, and can tangle easily around

the pinch rollers or other parts inside the unit,

causing unit failure.

• Remove a cassette tape from the unit when

not listening to it for a whilst. If you leave a

tape in the unit too long, it may stick to the

tape head and cause unit malfunction.

• Characters in the LCD may become difficult

to read in temperatures below 41 ˚F (5 ˚C).

• The illustrations of the display and the panel

appearing in this manual are examples used

to explain more clearly how the controls are

used. Therefore, what appears on the display

in the illustrations may differ from what

appears on the display on the actual

equipment, and some of the illustrations on

the display may represent something

impossible in actual operation.

• The functions that can be used and the

information that can be displayed will differ

depending on the external disc players being

connected.

— 4 —

General features

Release button

Power

SRC /

AUD

PWR OFF

Turning on the power:

Press the SRC button.

NOTE

EJECT

SRC

PWR

OFF

Turn the power on before carrying out the following procedures.

PTY

DISC

Turning off the power:

Hold down the PWR OFF button for one second or more.

LOUD

SCAN

B.S/RDM

REP

D.SCN

M.RDM

CLK

VOL ADJ NAME.S

Volume

ATT / LOUD

#1 – 5

CLK

Increasing Volume:

Press the u button to turn up the volume.

Decreasing Volume:

Press the d button to turn down the volume.

LOUD indicator

ATT indicator

— 5 —

General features

Turning Attenuator On/Off:

Switching Modes

Press the ATT button to switch the attenuator on and off.

When the attenuator is on, the ATT indicator blinks.

When the attenuator is off, the volume returns to the original

level.

Switching Modes:

Each time you press the SRC button, the mode switches as

follows:

Egnlish

NOTE

▼

Tuner mode

Turning the volume up, or turning it all the way down deactivates

the attenuator function.

▼

Tape mode

▼

External disc control mode 1

▼

External disc control mode 2/AUX mode

▼

Loudness

Standby mode

This function amplifies low and high tones when the volume is

turned down.

The LOUD indicator lights up, when the loudness function is

on.

Selecting the standby mode:

Press the SRC button repeatedly to select to "ALL OFF" .

When "ALL OFF" is displayed, the standby mode is turned on.

The standby mode turns all functions off although leaving the

unit’s power on. Use this mode when you want to have the

display illuminated but do not want to listen to anything.

Turning Loudness On/Off:

Hold down the LOUD button for one second or more to switch

the loudness on and off.

NOTE

• The mode switches to the next mode from any mode which

cannot be used.

• The external disc control mode will differ depending on the unit

that is connected.

Audio Control Setting

Adjust various parameters of sound quality.

• The AUX mode is available only when the changer / AUX

switching adapter (KCA-S210A or CA-C1AX) or CD changer

(KDC-CPS85, KDC-CX85, KDC-CPS82 or KDC-CX82) is

connected to this unit.

During the AUX mode, "AUX" will show in the display.

When the CA-C1AX is being used, the AUX Mode will replace

the External Disc Control Mode.

Press the AUD button to enter the control mode.

Selecting mode

Press either the FM or AM button.

Each time the button is pressed, the adjustment mode will

change.

Please refer to the following for the contents of the adjustment

modes.

NOTE

Source tone memory

Each source (tape, CD, MD, FM, AM, and disc changer) has its

own memory in which to store the bass and treble tone settings.

The settings made for a particular source are then recalled

automatically whenever you use that source (e.g., FM mode uses

Attenuator

This function allows you to turn down the volume quickly.

— 6 —

the tone settings made for FM, AM for AM, etc.).

"BAL" : Adjust the balance level.

Adjust each mode

Press the 4/¢ button.

Setting values: Left 15 – Right 15

Please refer to the following for the adjusting values.

Press the AUD button to end the control mode.

"FAD" : Adjust the fader level.

Setting values: Front 15 – Rear 15

"EC"/"dB" : Recalling the kenwood preset sound setting

Press the preset buttons (#1-5).

Settings: #1;FLAT, #2;ROCK, #3;POPS/TOP40, #4;JAZZ,

#5;EASY

Clock display

NOTE

Turning clock display On/Off:

Each time you press the CLK button, the display switches

between the clock and each mode display.

You can call the following settings with this function; bass centre

frequency, bass level, bass quality factor, bass extension, treble

centre frequency, and treble level setting.

"BAS" : Adjust the bass level.

Setting values: - 8 – + 8

"TRE" : Adjust the treble level.

Setting values: - 8 – + 8

— 7 —

General features

damaged by shocks or jolts. For that reason, keep the faceplate

in its special storage case whilst detached.

TEL Mute

Shut down the audio system temporarily whenever an

incoming call is received.

Egnlish

NOTE

The function will not work if a cable is not connected to the car

phone.

• Do not expose the faceplate or its storage case to direct

sunlight or excessive heat or humidity. Also avoid places with

too much dust or the possibility of water splashing.

When the telephone rings:

When a call is received, "CALL" is displayed and all the unit

functions are temporarily interrupted.

Reattaching Faceplate:

Restoring Original Unit Source During Phone Call:

Press the SRC button.

Align the projections on the unit with the grooves on the

faceplate.

"CALL" disappears from the display, and the volume of the

original source is restored gradually.

Push the faceplate in until it clicks.

The faceplate is locked in place, allowing you to use the unit.

Turning TEL Mute Function Off After Phone Call:

Hang the phone up.

"CALL" disappears from the display.

The original source (i.e., the one used before the phone call) is

returned to automatically, and the volume restored gradually.

Theft Deterrent Faceplate

The faceplate of the unit can be detached and taken with you,

helping to deter theft.

Projections

Release button

Grooves

Removing Faceplate:

Press the release button.

The faceplate is unlocked, allowing you to detach it.

NOTE

• The faceplate is a precision piece of equipment and can be

— 8 —

Tuner features

Tuning

SRC

Press the SRC button repeatedly until the tuner mode is

obtained. "TUNER" is displayed only when the tuner mode is

selected.

EJECT

SRC

PWR

OFF

PTY

Press either the FM or AM button to select the band.

Each time you press the FM button, the band switches

between the FM1, FM2 and FM3.

DISC

LOUD

SCAN

B.S/RDM

REP

D.SCN

M.RDM

DISC

CLK

VOL ADJ NAME.S

Press the AM button to select the MW and LW bands.

• Auto Seek Tuning

Press the ¢ button to seek increasing frequencies.

Press the 4 button to seek decreasing frequencies.

• Preset station seek tuning

CLK

#1~6

Press the ¢ button to move to the next preset station (i.e.,

the one with the next highest number), and the 4 button to

move to the last preset station (i.e., the one with the next

lowest number).

NOTE

If the frequencies stored at the preset numbers receive

stations which were not originally memorized when traveling

long distances, the preset number is not displayed. In such

cases, pressing the 4/¢ button to use preset station seek

will receive channel 1.

Band display

• Manual Tuning

Press the ¢ button to increase the frequency by one step.

Press the 4 button to decrease the frequency by one step.

NOTE

• The ST indicator lights up when stereo broadcasts are being

received.

• Please see the menu settings about selecting tuning mode.

(page24)

ST indicator

Frequency

Preset station number

— 9 —

Tuner features

RDS features

Station Preset Memory

Store the frequency of the station currently being listened to.

You can then recall that station with a single touch of a button.

PTY MENU

Egnlish

EJECT

SRC

Select the band/ station that you want to have stored.

PWR

OFF

PTY

Hold down the button (#1-6) that you want to use for the

station, for two seconds or more.

The button number blinks once in the display to indicate that

the data has been stored.

DISC

LOUD

SCAN

B.S/RDM

REP

D.SCN

M.RDM

DISC

CLK

VOL ADJ NAME.S

Recalling a Preset Station:

Press the preset station button (#1-6) for the desired station.

The number of the recalled station is displayed.

NOTE

TI/VOL ADJ CLK

#1~6

You can store 6 stations in each of the FM1, FM2, FM3, and AM

(MW and LW) bands.

Clock display

Turning clock display On/Off:

Each time you press the CLK button, the display switches

between the Programme Service name (during RDS station

reception) and clock.

PTY indicator

Displaying Frequencies:

Hold down the CLK button for one second or more.

The frequency for the RDS station will be displayed for five

seconds instead of the station name.

TI indicator

™ indicator

— 10 —

RDS (Radio Data System)

Traffic Information Function

You can listen to traffic information. If you are listening to

tapes or discs, they will continue playing until a traffic bulletin

is broadcast.

RDS is a digital information system that lets you receive signals

besides those of regular radio programmes, such as network

information being transmitted from radio stations.

When listening to an RDS station (ie, a station with RDS

capability), the programme service name of the station is

displayed along with the frequency, advising you quickly which

station is being received.

RDS (Radio Data System) stations also transmit frequency data

for the same station. When you are making long trips, this

function automatically switches to the particular frequency with

the best reception for the particular network of stations that

you want to listen to. The data is automatically stored,

allowing you to switch quickly to another RDS stations,

broadcasting the same programme, that has better reception.

These include stations stored in the station preset memory that

you often listen to.

Turning TI function On/Off:

Press the TI button to turn the function on and off.

When the function is on, the TI indicator is turned on.

When none is being received, the TI indicator will blink on and

off. When a traffic information station is being received, the TI

indicator will turn on.

When a traffic bulletin begins to be broadcast, "TRAFFIC" will

be displayed, and reception will begin at the preset volume.

If you are listening to a tape or disc when a traffic bulletin

begins, they will automatically be turned off. When the bulletin

ends or poor reception is experienced, the tape or disc will

begin playing again.

NOTE

Pressing the TI button whilst in the MW/LW band automatically

switches reception to the FM band. However, the MW/LW band

is not returned to when the TI button is pressed again.

Enhanced Other Network

Stations that offer <Enhanced Other Network> also transmit

information about other RDS stations that have traffic

information. When you are tuned to a station that is not

transmitting traffic information, but another RDS station starts

transmitting a traffic bulletin, the tuner automatically switches

to the other station for the duration of the bulletin.

Switching to a Different Traffic Information Station:

Use the 4 / ¢ buttons to make an auto seek of the TI

stations in a certain band.

NOTE

• When you are listening to a tape or disc, you cannot change to

another TI station.

• When the auto TP seek function is turned on and reception

starts to weaken, the tuner automatically seeks traffic

information stations with better reception.

• If you are tuned to a station that is not a traffic information

station itself but which provides <Enhanced Other Network>

services, you can still have traffic information received.

• Holding the TI button down for one second or more when the TI

function is on in the disc control mode results in a change to the

frequency display of the traffic information station for five

seconds.

Alarm

When an emergency transmission (announcing disasters, etc.)

is sent, all current functions are interrupted to allow the

warning to be received.

— 11 —

RDS features

the desired language and then the CLK button.

English is #1, French is #2, and German is #3.

Presetting Volume for Traffic Information/News

Preset the volume level to be used for traffic information and

news broadcasts.

Select the type of programme to be received

• Press either the FM or AM buttons repeatedly until the type

of programme you want to listen to.

Egnlish

Tune into the station for which you want to set the volume.

Adjust the volume to the desired level.

The selection includes:

Speech

(SPEECH)

(NEWS)

Hold down the TI VOL ADJ button for two seconds or more.

The volume level blinks once in the display to indicate that the

data has been stored.

Future traffic information/news broadcasts are heard at the

preset level.

1. News

2. Current Affairs

3. Information

4. Sports

(AFFAIRS)

(INFO)

(SPORT)

5. Education

6. Drama

(EDUCATE)

(DRAMA)

(CULTURE)

(SCIENCE)

(VARIED)

(POP M)

NOTE

7. Culture

• The volume cannot be lowered by this function during tuner

reception. The volume is only set when it is louder than the

listening volume of the tuner.

• You can arrange only to listen to traffic information or news

bulletins with at preset volume with the volume set at

minimum.

8. Science

9. Varied

10. Pop Music

11. Rock Music

12. Easy Listening Music

13. Light Classical

14. Serious Classical

15. Other Music

16. Weather

(ROCK M)

(EASY M)

(LIGHT M)

(CLASSICS)

(OTHER M)

(WEATHER)

(FINANCE)

17. Finance

Programme Type (PTY) Function

Conduct auto seek tuning only on those stations with selected

kinds of programmes.

18. Children’s programmes (CHILDREN)

19. Social Affairs

20. Religion

(SOCIAL A)

(RELIGION)

(PHONE IN)

(TRAVEL)

(LEISURE)

(JAZZ)

21. Phone In

Press the 38(PTY) button.

22. Travel

The PTY indicator will turn on, and the Programme Type

Selection (PTY) Mode entered.

23. Leisure

24. Jazz Music

25. Country Music

26. National Music

27. Oldies Music

28. Folk Music

29. Documentary

Music

If you make no key input in 30 seconds, the mode will

automatically turn off.

(COUNTRY)

(NATION M)

(OLDIES)

NOTE

You cannot use this function whilst the traffic information

function is turned on.

(FOLK M)

(DOCUMENT)

(MUSIC)

NOTE

Changing the Display Language to French or German

(Speech.....1~9,16~23, 29, Music.....10~15, 24~28)

• You can select the type of programme directly by pressing a

preset button. The buttons are factory-set to the following

type of programmes:

In the PTY mode, hold down the CLK button for one second or

more to display the name of the language currently used.

If you want to change the language, press the preset button for

— 12 —

Cassette player features

1. Music

4. Other Music

2. Speech

5. Serious Classical

3. News

6. Varied

2 3

SRC

NOTE

Changing the Preset Button Settings for Programme Type

After selecting the type of programme to be stored in a certain

preset button, hold down that button for two seconds or more.

The previously stored data for that button are erased and the new

programme type is stored.

EJECT

SRC

PWR

OFF

PTY

DISC

Seeking the selected programme type

LOUD

SCAN

B.S/RDM

REP

D.SCN

M.RDM

DISC

CLK

VOL ADJ NAME.S

Press the 4 or ¢ button to make a seek of frequencies

with your selected type of programme.

The display blinks and the seek starts.

If your selected type of programme is found, the name of the

station is displayed and the station is tuned into.

"PTY" blinks in the display for about 30 seconds.

If you make no key input in 30 seconds, the PTY selection

mode will turn off automatically.

B.S

REP

CLK

NOTE

If no programme can be found, "NO PTY" is displayed.

If you want to select another type of programme, repeat steps 2

and 3 above.

Switching to Other Stations with the Same Type of Programme:

When "PTY" is blinking in the display, perform auto seek tuning.

The tuner scans for another station with the same type of

programme.

Tape indicator

Cancelling Programme Type Function During Its Operation:

Press the 38(PTY) button.

— 13 —

Cassette player features

Playing Cassette Tapes

Blank Skip

Automatically fast forwards to the beginning of the next track

when long blank spaces (10 seconds or more) are detected,

continuing tape playback. This function is on, when unit is first

powered on.

Loading and Playing Cassettes:

Load a cassette with the tape exposed on the right.

The tape starts playing automatically.

Egnlish

Playing Cassettes Already Loaded:

Turning Blank Skip Function On/Off:

Press the B.S button to switch the blank skip function on and

off.

"BS ON" is displayed when the blank skip function is turned on.

NOTE

Press the SRC button repeatedly until tape mode is obtained.

"TAPE" is displayed when the tape mode has been selected.

Listening to the other side:

Press the 23 button.

Tape play switches to the other side.

• If the blank space contains hiss noise, the blank skip function

may not work correctly.

• Sections recorded at low levels may trigger the blank skip

function if they last for 10 seconds or more.

Stopping and Ejecting Cassettes:

Hold down the 23 button for one second or more.

The tape stops playing and the cassette ejects.

NOTE

• Remove a cassette from the unit when not listening to it for a

whilst. If you leave it in the unit too long, the tape may stick to

the tape head and cause the unit to malfunction.

• The tape counter is not exact, but only represents an

approximation of the elapsed time.

Tape Advance

Rewinds to the beginning of the current track (or fast forwards

to the beginning of the next track), continuing tape playback.

Rewinding tape to the beginning of current track:

Press the 4 button, and the tape will rewind to the beginning

Fast Forwarding and Rewinding Cassette Tapes

of the current track and automatically start playing again.

Fast Forwarding Tapes:

To advance to the beginning of the next track:

Press the ¢ button, and the tape will advance to the

beginning of the new track and automatically start playing

again.

Press the FM button.

Rewinding Tapes:

Press the AM button.

Cancelling:

NOTE

Press the 23 button.

The tape advance function "knows" where a track begins by

detecting the blank space preceding it (i.e., the space between

tracks). However, when the blank space lasts for less than 4

seconds or contains noise, this function may not operate

correctly. Furthermore, sections recorded at low levels may

trigger the function if they last for 4 seconds or more.

Normal tape play returns.

— 14 —

External disc control features

Music Repeat

Repeatedly plays the current track.

SRC

^DISC+

Turning Music Repeat Function On/Off:

Press the REP button to switch the music repeat function on

and off.

EJECT

SRC

PWR

OFF

PTY

DISC

"REP ON" is displayed when music repeat is turned on.

Cancelling Music Repeat Function:

LOUD

SCAN

B.S/RDM

REP

D.SCN

M.RDM

DISC

CLK

VOL ADJ NAME.S

Press either the REP or 23 button.

NOTE

The music repeat function "knows" where a track begins by

detecting the blank space preceding it (i.e., the space between

tracks). However, when the blank space lasts for less than 4

seconds or contains noise, this function may not operate

correctly. Furthermore, sections recorded at low levels may

trigger the function if they last for 4 seconds or more.

RDM

D.SCN

CLK/NAME.S

M.RDM

DISC–

SCAN

REP

Track number

Disc number

Track time

Disc indicator

— 15 —

External disc control features

■ When a unit equipped with an O-N switch is to be connected,

please also see the instruction manual of this unit.

Set the O-N switch to "N". "N"-operation will be set.

• "CD" ...when a CD player is connected

• "DISC" ...when a disc changer is connected

• "DISC-1" , "DISC-2" ...when two disc changers are connected

"N"-operation:

Pausing and Restarting Disc Play:

Egnlish

• The disc title and track title of the CD text can be displayed.

• The disc name will be displayed when the name has been

registered to any connected unit with the Presetting Disc

Names function, or when the playing unit contains a disc to

which the disc title has been recorded.

Press the 38 button to make the disc pause.

Press the same button again to start play again.

NOTE

• When one disc has finished playing its last track, the next disc in

the changer starts playing. When the last disc in the changer

has finished, the player returns to the first disc and starts

playing it.

"O"-operation:

• CD text cannot be displayed.

• Regardless of the control unit, the characters that can be

registered with the Presetting Disc Names function are "A~Z

0~9 /, +, –, ∗, =, <, >, [ , ]".

• Disc #10 is displayed as "0".

• The disc name will be displayed when the name has been

registered to the playing unit with the Presetting Disc Names

function.

Fast Forwarding and Reversing Disc Play

NOTE

Fast Forwarding Disc Play:

The CD text, Presetting Disc Names, and Disc Name Preset Play

functions may not be operational depending on the unit.

Hold down on the ¢ button.

Release your finger to play the disc at that point.

Reversing Disc Play:

Hold down on the 4 button.

Release your finger to play the disc at the point.

NOTE

You cannot use reverse play between tracks depending on the

model being connected. Instead, the reverse play function is

cancelled when it reaches the beginning of a track, at which point

normal play automatically resumes.

Playing Disc mode

This funciton permits the connection of optional players and

the playing of discs.

Playing Discs:

Press the SRC button repeatedly to select the external disc

control mode.

Track Search

Search forwards or backwards through the tracks on the disc

until you reach the one that you want to listen to.

The disc will start playing.

NOTE

Making a Reverse Track Search:

The external disc control mode will differ, depending on the unit

that is connected.

Mode Display Examples

Press the 4 button to display the desired track number.

Press once to search back to the beginning of the current track,

— 16 —

twice to search back to the beginning of the previous track, and

so forth.

Play starts at the beginning of the displayed track number.

Track / Disc Repeat

Repeat playing the current track or disc.

NOTE

Turning Repeat Play Function On/Off:

Press the REP button to switch the repeat play function on and

off as follows :

(For disc changers)

Pressing the 4 button whilst listening to track 1 only searches

back to the beginning of that track. The reverse search is not

"recycled" to the last track on the disc.

▼

Track Repeat ON

Making a Forward Track Search:

▼

Press the ¢ button to display the desired track number.

Press once to fast forward to the next track, twice to fast

forward to the track after that, and so forth.

Disc Repeat ON

▼

Track/Disc Repeat OFF

Play starts at the beginning of the displayed track number.

"TREP/REP ON" is displayed and the track number blinks in the

display when track repeat is on.

"DREP ON" is displayed and the disc number blinks in the

display when disc repeat is on.

NOTE

(For disc changers)

You cannot make a forward track search when listening to the last

track on a disc.

NOTE

Repeat play is cancelled when you eject the disc.

Disc Search

Search forwards or backwards through the discs in a disc

changer until you reach the one that you want to listen to.

Track Scan

Making a Reverse Disc Search:

Successively play the beginning of each track on a disc until

you find the track that you want to listen to.

Press the DISC– button to display the desired disc number.

Each time the button is pressed, the displayed disc number

decreases by one.

Starting the Track Scan:

Play starts at the beginning of the displayed disc.

Press the SCAN button. "TSCN/SCAN ON" is displayed and the

first 10 seconds of each track are played, and the tracks are

played in order.

Making a Forward Disc Search:

Press the DISC+ button to display the desired disc number.

Each time the button is pressed, the displayed disc number

increases by one.

The track number currently being heard blinks in the display.

Stopping to Listen to the Track Being Scanned:

Press the 38 or SCAN button again to stop the scan and keep

on listening to a track normally.

Play starts at the beginning of the displayed disc.

NOTE

"LOAD" is displayed when discs are being exchanged on the disc

changer.

• The track scan function is cancelled when you eject the disc.

• The track scan function only scans each track on a disc once.

— 17 —

External disc control features

NOTE

Disc Scan

Random play is cancelled when you eject the disc.

Successively play the beginning of each disc on a changer until

you find the one that you want to listen to.

Egnlish

Starting the disc scan:

Press the D.SCN button. "DSCN ON" is displayed and the first

10 seconds of each disc are played, in the order in which they

are loaded on the changer.

Magazine Random Play

Play the tracks on all the discs in the disc changer in random

order.

The disc number currently being heard blinks in the display.

Stopping to Listen to the Disc Being Scanned:

Press the 38 or D.SCN button again to stop the scan and keep

on listening to the disc normally.

Press the M.RDM button to switch the magazine random play

function on and off.

NOTE

"MRDM ON" is displayed when magazine random play is turned

on.

• The disc scan function is cancelled when you eject the disc.

• The disc scan function only scans each disc on the changer

The display of the disc and track numbers change continuously

as the next track is being selected.

once.

• "LOAD" is displayed when discs are being exchanged on the disc

changer.

When the disc/track has been selected, play starts.

The selected disc/track number blinks in the display as it is

being played.

NOTE

This function is not available with the following models:

KDC-C200/C300/C400/C301/C401

Random Play

Play all the tracks on the current disc in random order.

To change the track being heard, press the ¢ button.

Another disc/track is selected and played.

Press the RDM button to switch the random play function on

and off.

NOTE

"RDM ON" is displayed when random play is turned on.

The display of the track number changes continuously as the

next track is being selected.

When the track has been selected, play starts.

The selected track number blinks in the display as it is being

played.

• Magazine random play is cancelled when you eject the disc.

• The time needed for random selection depends on the number

of discs loaded in the disc magazine.

NOTE

Text / Title Scroll

This function permits the text to be scrolled and the entire text

to be displayed. The scrolling method differs depending on the

setting of scrolling in the menu.

When all the tracks on a certain disc have been played using the

random play function, the next disc on the changer starts playing

(with the random play function still turned on).

To change the track being heard, press the ¢ button.

To scroll manually:

Another track is selected and played.

— 18 —

Press the CLK button to display the disc title or the track title.

Holding down the CLK button for one second or more results in

one scrolling display of the titles.

To scroll automatically:

Press the CLK button to display the disc title or the track title.

The titles will be displayed in one scrolling display.

NOTE

When the disc or track to be played changes, the title is displayed

in one scrolling display.

Holding down the CLK button for one second or more results in

one scrolling display of the titles.

NOTE

• Please see the menu settings (page 25) about switching

between manual scrolling and automatic scrolling.

• Only units with a CD text feature permit title display.

— 19 —

External disc control features

The disc name is stored and the disc name preset mode is

cancelled.

Presetting Disc Names

Store the names of discs to be displayed when played.

If you make no entry in a 10-second period, the name will be

stored with the characters entered so far.

Play the disc whose name you want to preset.

Egnlish

NOTE

• The number of discs whose names can be stored will differ

depending on the disc changer that is connected. Please see

your disc changer manual for details.

• Discs are identified by their total length and number of tracks. If

you play another CD that happens to have exactly the same

specifications as another CD whose name is stored, the wrong

name will be displayed for it.

• If you want to change the name of a disc, repeat steps 1 and 2

to display the name, and then repeat steps 3 and 4 to enter the

changes.

• Pressing the reset button does not erase the disc names stored

in a disc changer.

• This function is not available for disc changers that do not

feature the Disc Name Preset function.

• This procedure is not to be used to store the disc and track titles

for MDs that you record.

Hold down the NAME.S button for two seconds or more.

"NAME SET" is displayed and the disc name preset mode is

entered.

The cursor blinks in the position where character input can be

made.

Press either the 4 or ¢ button to move the cursor to the

desired position.

The 4 button moves the cursor to the left, and the ¢

button to the right.

You can also move the cursor left or right by pressing the

^TRACK+ or TRACK– buttons, respectively, on the remote

control.

Press the DISC+ or DISC– button to display the desired

character.

NOTE

The operation and characters that can be entered may change

as listed below, depending on the unit that is connected.

^{Press the DISC}+ or DISC– button to display the desired

character.

Besides the alphabet (capital letters only) and numerals, you

can choose the following characters: /, +, –, *, =, <, >, [ and ]

Continue steps 3 and 4 until all the characters are chosen for

the name.

NOTE

You can enter up to 8 characters for each name.

Press either the NAME.S button on the main unit or the OK

button on the remote control.

— 20 —

Menu settings

Switching Display for Discs

Switch the display that appears whilst discs are playing.

Switching Display for Discs:

EJECT

Each time you press the CLK button, the display during disc

play switches as follows.

SRC

PWR

OFF

PTY

DISC

Track time

LOUD

SCAN

B.S/RDM

REP

D.SCN

M.RDM

DISC

CLK

VOL ADJ NAME.S

Disc name (DNPS)

Disc title (Units featuring CD text/MD only)

Track title (Units featuring CD text/MD only)

Clock

NOTE

• You can give names to discs through the presetting disc name

function (see p. 20).

Note that depending on the unit, display may not be possible.

• If you try to display the name of a disc that does not have one,

"NO NAME" is displayed instead.

• When there is an attempt to display the title of a disc for which

the disc title/track title has not been recorded, "NO TEXT" is

displayed for CD and "NO TITLE/NO NAME" is displayed for MD.

• Depending on the type of characters of the CD Text, some

characters may not be displayable.

AUTO indicator

Menu display

NEWS indicator

— 21 —

Menu settings

Menu System

Touch Sensor Tone

This function produces a beep sound that accompanies button

operation. It can be switched on or off.

You can set the defaults for additional functions in the menu

mode.

Make a setting for each function, referring to the following

operations.

Egnlish

Display and setting:

"BEEP ON" : Beep setting is on.

"BEEP OFF" : Beep setting is off.

Enter the menu mode

Hold down the MENU button for one second or more.

"MENU" is displayed when the menu mode is entered.

The function that you can adjust is indicated with the current

settings displayed.

NOTE

The beep sound is not output from the preout jacks.

Selecting function to set

Press the FM button to search through the functions until you

see the one you want to adjust in the display.

Manual Time Adjustment

Adjust the time manually.

Press the AM button to search through the functions backward.

Example: If you want to switch the setting of the touch sensor

tone function from on to off, first search through the

functions until you see "BEEP ON" in the display.

NOTE

This adjustment is available only when the automatic time

adjustment is set to off.

Display and setting:

Select the display "CLK ADJ" during the selecting function in

the menu system.

Changing setting for currently displayed function

Press either the 4 or ¢ button.

Hold down either the 4 or ¢ button for two seconds or

more to enter the Manual time adjustment mode.

The time display will blink.

The setting will change for each function.

Example: The setting of the touch sensor tone will switch from

on to off, and "BEEP OFF" is displayed.

• Adjusting the hours

Press the FM button to advance the hours, or press the AM

button to make the hours go back.

• Adjusting the minutes

Press the ¢ button to advance the minutes, or press the

Ending the menu mode

Press the MENU button.

4 button to make the minutes go back.

NOTE

Make sure to end the menu mode when finished.

If you fail to end the menu mode, several functions may not

operate properly, including the Traffic Information function and

the Alarm function.

Automatic Time Adjustment

With automatic time adjustment, you can set the clock time

automatically according to time data sent from RDS stations

(after receiving RDS signals for several minutes). You can also

— 22 —

set the time manually if the automatic time adjustment function

is turned off. The factory default is automatic time adjustment.

News Bulletin Function

with PTY News Timeout Setting

Display and setting:

You can arrange to have news bulletins interrupt your current

listening source, including other radio stations. When the News

Bulletin function is on, the PTY News Timeout setting allows

you to set the interval during which further news interruption

cannot take place. You can adjust the PTY news interruption

period from 10 to 90 minutes for each journey.

"SYNC ON" : Automatic time adjustment

"SYNC OFF" : Manual time adjustment

Adjusting Time Automatically:

Tune into an RDS station for 3 or 4 minutes.

The time adjusts automatically to the correct local time.

NOTE

Display and setting:

"NEWS OFF/ 00M/ 10M/ 20M/ 30M/ 40M/ 50M/ 60M/ 70M/

The time is not adjusted when the RDS station you are tuned to is

not transmitting a time signal. Choose another RDS station in

such a case.

80M/ 90M"

(M= minutes)

: When you select the news interruption timeout interval, the

News function turns on and the NEWS indicator lights up.

When a news bulletin is received, "NEWS" will be displayed

and reception will begin at the preset volume.

NOTE

Disabled System Indicator (DSI)

• If you choose the "20M" setting, further news bulletins will not

be received for 20 minutes once the first news bulletin is

received.

• This function is only available if the desired station sends PTY-

code for news bulletin or belongs to <Enhanced Other

Network>-Network sending PTY-code for news bulletin.

• If you turn on the news bulletin function in the MW/LW band,

the band is switched automatically to the FM band.

However, the MW/LW band is not returned to when you turn off

the function.

A red indicator blinks on the unit after the faceplate is removed,

warning potential thieves. The factory default for this function

is "ON".

Display and setting:

"DSI ON" : The disabled system indicator is on.

"DSI OFF" : The disabled system indicator is off.

Selectable Illumination

You can switch the colour of the button illumination between

green and red.

Local Seek Function

With the local seek function turned on, auto seek tuning skips

Display and setting:

stations with relatively poor reception.

"COL GRN" : The colour of the illumination is green.

"COL RED" : The colour of the illumination is red.

Display and setting:

"LO.S ON" : The local seek function is on.

"LO.S OFF" : The local seek function is off.

— 23 —

Menu settings

Press the MENU button whilst auto memory entry is taking

place to stop the process.

Selecting Tuning Mode

You can choose from three tuning modes: auto seek, preset

station seek, and manual.

Recalling a Preset Station:

Press the preset station button (#1-6) for the desired station.

The number of the recalled station is displayed.

Egnlish

Display and setting:

"AUTO 1" : Auto seek tuning mode

"AUTO 2" : Preset station seek tuning mode

"MANUAL" : Manual tuning mode

AF (Alternative Frequency) Function

When poor reception is experienced, automatically switch to

another frequency broadcasting the same programme in the

same RDS network with better reception.

The ™ indicator lights up when the AF function is turned

on.

Auto Memory Entry

You can automatically store all the receivable frequencies in

the band currently being listened to, and then recall them with

the touch of a button later. This function is especially useful

when you are travelling and do not know what stations are

available. Up to 6 frequencies can be stored this way.

Display and setting:

"AF ON" : The AF function is on.

"AF OFF" : The AF function is off.

NOTE

Display and setting:

• When no other stations with stronger reception are available for

the same programme in the RDS network, you may hear the

incoming broadcast in bits and snatches. Turn off the AF

function in such a case.

• The AF function can be turned on or off even when the standby

mode has been turned on. If the power is on, the AF function

tunes in to stations that offer good reception.

Select the display "A-MEMORY" during the selecting function in

the menu system.

Hold down either the 4 or ¢ button for two seconds or

more to start auto memory function.

The numbers of the preset station buttons showed in order.

When all the stations in a certain band are stored in the preset

memory, the auto memory entry stops. The tuner then plays

the last station received.

NOTE

Restricting RDS Region (Region Restrict Function)

• When the AF function is turned on whilst auto memory entry

takes place, only RDS stations (i.e., stations with RDS capability)

are stored. RDS stations that have been preset for FM1 cannot

also be preset in FM2 or FM3.

• When the local seek function is turned whilst auto memory

entry takes place, stations with poor reception are not stored.

• When the Traffic Information function is on , only the local traffic

information station frequency will be stored.

You can choose whether or not to restrict the RDS channels,

received with the AF function for a particular network, to a

specific region. When the Region Restrict Function is on, the

region is restricted.

Display and setting:

"REG ON" : The Region Restrict Function is on.

"REG OFF" : The Region Restrict Function is off.

Cancelling Auto Memory Entry During Its Operation:

— 24 —

"SCL AUTO" : Automatic scrolling

"SCL MANU" : Manual scrolling

NOTE

Sometimes stations in the same network broadcast different

programmes or use different programme service names.

Auto TP Seek Function

When the TI function is on and poor reception conditions are

experienced when listening to a traffic information station,

another traffic information station with better reception will be

searched for automatically. This function is on, when unit is

first powered on.

Display and setting:

"ATPS ON" : The Auto TP Seek Function is on.

If the traffic information station you are tuned to

experiences poor reception, this function

automatically seeks another TP station.

"ATPS OFF" : The Auto TP Seek Function is off.

Monaural Reception

When poor stereo reception is experienced, this function will

reduce noise and improve listening conditions.

Display and setting:

"MONO ON" : The monaural reception is on.

"MONO OFF" : The monaural reception is off.

Text Scroll

This function permits the CD text and MD title to be scrolled

and the entire text to be displayed. Switching between manual

scrolling and automatic scrolling is permitted. The factory

default is manual scrolling.

Display and setting:

— 25 —

Accessories

External view

Number of items

2CAUTION

• If your car is not prepared for this special connection-system,

consult your Kenwood dealer.

..........................................1

• Only use antenna conversion adapters (ISO-JASO) when the

antenna cord has an ISO plug.

• Make sure that all cable connections are securely made by

inserting jacks until they lock completely.

..........................................2

..........................................1

• If your vehicle's ignition does not have an ACC position, or if

the ignition cable is connected to a power source with constant

voltage such as a battery cable, the power will not be linked

with the ignition (i.e., it will not turn on and off along with the

ignition). If you want to link the unit's power with the ignition,

connect the ignition cable to a power source that can be turned

on and off with the ignition key.

1:KRC-478R/378R/33R only

• If the fuse blows, first make sure that the cables have not

caused a short circuit, then replace the old fuse with one with

the same rating.

• Do not let unconnected cables or terminals touch metal on the

car or anything else conducting electricity. To prevent short

circuits, also do not remove the caps on the ends of the

unconnected cables or the terminals.

• Connect the speaker cables correctly to the terminals to which

they correspond. The unit may receive damage or fail to work if

you share the - cables and/or ground them to any metal part in

the car.

• After the unit is installed, check whether the brake lamps,

indicators, wipers, etc. on the car are working properly.

• Insulate unconnected cables with vinyl tape or other similar

material.

2CAUTION

The use of any accessories except for those provided might

result in damage to the unit. Make sure only to use the

accessories shipped with the unit, as shown above.

Installation Procedure

1. To prevent short circuits, remove the key from the ignition and

disconnect the -terminal of the battery.

2. Make the proper input and output cable connections for each unit.

3. Connect the cable on the wiring harness.

4. Take Connector B on the wiring harness and connect it to the

speaker connector in your vehicle.

5. Take Connector A on the wiring harness and connect it to the

external power connector on your vehicle.

6. Connect the wiring harness connector to the unit.

7. Install the unit in your car.

• Some disc changers need conversion cables for connection.

See the section on "Safety Precautions" for details.

• If the console has a lid, make sure to install the unit so that the

faceplate does not hit the lid when closing and opening.

8. Reconnect the - terminal of the battery.

9. Press the reset button.

— 26 —

Connecting Cables to Terminals

■

ISO connector unsupported car (KRC-478R/378R/33R only)

2CAUTION

When only two speakers are being connected to

the system, connect the connectors either to both

the front output terminals or to both the rear

output terminals (do not mix front and rear). For

example, if you connect the + connector of the

left speaker to a front output terminal, do not

connect the - connector to a rear output

terminal.

Front right output (Red)

(KRC-478R/478RV only)

Front left output (White)

(KRC-478R/478RV only)

Rear left output (White)

Rear right output (Red)

Power Control terminal

(P.28)

Fuse (10A)

Plug (P.29)

FM/AM

antenna input

KENWOOD disc changer

/ DAB control input

2WARNING

If you connect the ignition cable (red) and the

battery cable (yellow) to the car chassis (ground),

you may cause a short circuit, that in turn may

start a fire. Always connect those cables to the

power source running through the fuse box.

NOTE

To connect the Disc changer or

DAB unit, consult each manual.

Antenna Cord (ISO)

NOTE

Antenna Conversion Adaptor

(ISO–JASO) (Accessory3)

To connect the KENWOOD

navigation system, consult

your navigation manual.

TEL mute terminal

White/Black

Wiring harness

(Accessory1)

If no connections are made, do not cut the tube off from

the edge of the cable.

To front left

speaker

Power control/ Motor antenna

control cable (Blue/White)

Connect either to the power control terminal

when using the optional power amplifier, or

to the antenna control terminal in the vehicle.

FRONT • L

White

P.CONT.OUT

Gray/Black

ANT.

CONT.

Ignition key

switch

To front right

speaker

FRONT • R

ACC

Gray

Ignition cable (Red)

Green/Black

To rear left

speaker

Battery cable (Yellow)

Car fuse box

(Main fuse)

REAR • L

Car fuse box

Green

Purple/Black

Ground cable (Black) - (To car chassis)

–

To rear right

speaker

REAR • R

Purple

Battery

— 27 —

Connecting Cables to Terminals

■

Power Control Terminal Connections

ISO connector supported car

The output of the Power Control terminal is switched along

with the power on/off switching of the unit.

For Volkswagen car

This terminal can be connected to the P.CON (REMOTE)

terminal of the amplifier, or used as the power supply of the

special antenna cable for Volkswagen cars. (MAX. 400 mA)

Special antenna cable

(Commercially available)

Egnlish

To Power Control terminal

Antenna Conversion Adaptor

(ISO–JASO) (Accessory3)

Power Control terminal

(Flat terminal)

Antenna Conversion Adaptor

(ISO–JASO) (Accessory3)

Rear left output

(White)

Front right output (Red)

(KRC-478R/478RV only)

Power control cable

Front left output (White)

(KRC-478R/478RV only)

Power Control terminal

(P.28)

Fuse (10A)

Plug (P.29)

Antenna

Cord (ISO)

Power Amplifier

Antenna Cord (ISO)

Antenna Conversion

Adaptor (ISO–JASO)

(Accessory3)

KENWOOD disc changer

/ DAB control input

Special antenna cable

NOTE

(For Volkswagen car)

Car’s wiring

harness

FM/AM

antenna input

To connect the Disc changer

or DAB unit, consult each

manual.

(Commercially available)

Rear right

output (Red)

TEL mute terminal

NOTE

To connect the KENWOOD

navigation system, consult

your navigation manual.

— 28 —

Connecting Cables to Terminals

■

Connector Function Guide

Plug Setting

2WARNING

Connecting the ISO Connector

The pin arrangement for the ISO connectors depends on the type

of vehicle you drive. Make sure to make the proper connections

to prevent damage to the unit.

1 The A-7 pin (red) of the vehicle's ISO connector is linked with

the ignition, and the A-4 pin (yellow) is connected to the

constant power supply. (Default setting; KRC-478R/378R/33R)

Connector B

Connector A

*Plug

setting

Pin Numbers for

ISO Connectors

Cable Colour

Functions

External Power

Connector

Battery

A–4

Yellow

Red

Blue/White

Red

Yellow

Black

Ignition (ACC)

Power Control

Ignition (ACC)

Battery

Earth (Ground)

Connection

A–5

A–7

2 The A-7 pin (red) of the vehicle's ISO connector is connected

to the constant power supply, and the A-4 pin (yellow) is

linked to the ignition. (Default setting; KRC-478RV)

A–8

Speaker

Connector

Rear Right (+)

Rear Right (–)

Front Right (+)

Front Right (–)

Front Left (+)

Front Left (–)

Rear Left (+)

Rear Left (–)

B–1

B–2

B–3

B–4

B–5

B–6

B–7

B–8

Purple

Purple/Black

Gray

Gray/Black

White

White/Black

Green

Green/Black

*Plug setting: See right side.

— 29 —

Installation

■

Installation

Firewall or metal support

Screw (M4X8)

(commercially

available)

Egnlish

Bend the tabs of the

mounting sleeve with

a screwdriver or

similar utensil and

attach it in place.

Self-tapping

screw

(Commercially

available)

Metal mounting

strap

(Commercially

available)

NOTE

Make sure that the unit is installed securely in place. If the unit is

unstable, it may malfunction (eg, the sound may skip).

— 30 —

Installation

■

Removing the hard rubber frame

Removing the Unit

Refer to the section “Removing the hard rubber frame” and

then remove the hard rubber frame.

Engage the catch pins on the removal tool and remove the two

locks on the lower level.

Lower the frame and pull it forward as shown in the figure.

Remove the screw (M4×8) on the back panel.

Insert the two removal tools deeply into the slots on each side,

as shown.

Catch

Lock

Catch facing up

Screw (M4X8)

(commercially

available)

Accessory2 Removal tool

When the lower level is removed, remove the upper two

locations.

Lower the removal tool

toward the bottom, and pull

out the unit halfway whilst

pressing towards the

inside.

2CAUTION

Be careful to avoid injury from the catch pins on the removal tool.

NOTE

Pull the unit all the way out

with your hands, being

careful not to drop it.

The frame can be removed from the top side in the same

manner.

— 31 —

Troubleshooting Guide

What might appear to be a malfunction in your unit may just be the result of slight misoperation or miswiring.

Before calling service, first check the following table for possible problems.

PROBLEM

POSSIBLE CAUSE

SOLUTION

The power does not turn on.

The fuse has blown.

After checking for short circuits in the cables, replace the

fuse with one having the same rating.

Egnlish

No ACC position on vehicle ignition.

The Attenuator function is turned on.

Connect the same cable to the ignition as the battery cable.

Turn off the Attenuator function.

No sound can be heard, or the

volume is low.

The fader and/or balance settings are set all the way to

one side.

Reset the fader and/or balance settings.

The input/output cables or wiring harness are connected

incorrectly.

Reconnect the input/output cables and/or the wiring

harness correctly. See the section on "Connecting Cables

to Terminals".

The cassette tape is bad.

Try playing another cassette tape. If no problem is

experienced, the first tape was bad.

The tape does not go in. /

No sound can be heard even

though the tape display is

made.

The car ignition was turned off during tape eject; or the

tape was pulled out during loading, switching the mode to

tape mode even though no tape is in.

Press the Eject button.

Nothing happens when the

buttons are pressed.

The computer chip in the unit is not functioning normally.

The tape head is dirty.

Press the reset button on the unit (see page 4).

Clean the tape head, referring to the section on "Cleaning

the tape head" (see page 4).

The sound quality is poor or

distorted.

A speaker cable may be pinched by a screw in the car.

The speakers are not wired correctly.

Check the speaker wiring.

Reconnect the speaker cables so that each output

terminal is connected to a different speaker.

Radio reception is poor.

The car antenna is not extended.

Pull out the antenna all the way.

The antenna control cable is not connected.

Connect the cable correctly, referring to the section on

"Connecting Cables to Terminals".

— 32 —

Troubleshooting Guide

PROBLEM

POSSIBLE CAUSE

SOLUTION

The memory is erased when

the ignition is turned off.

The battery cable has not been connected to the proper

terminal.

Connect the cable correctly, referring to the section on

"Connecting Cables to Terminals".

The ignition and battery cable are incorrectly connected.

Connect the cable correctly, referring to the section on

"Connecting Cables to Terminals".

The TEL mute function does

not work.

The TEL mute cable is not connected properly.

Connect the cable correctly, referring to the section on

"Connecting Cables to Terminals".

The TEL mute function turns on

even though the TEL mute

cable is not connected.

The TEL mute cable is touching a metal part of the car.

Pull the TEL mute cable away from the metal part of the

car.

External disc control mode

PROBLEM

POSSIBLE CAUSE

SOLUTION

The disc control mode cannot

be selected.

No cable has been connected to the disc changer input

terminal on the unit.

Connect the cable to the disc changer input terminal on

the unit.

The specified disc does not

play, but another one plays

instead.

The specified CD is very dirty.

Clean the CD.

The CD is upside-down.

Load the CD with the labelled side up.

The disc is loaded in a different slot from that specified.

Eject the disc magazine and check the number for the

specified disc.

The disc is severely scratched.

Something is touching the disc changer.

The CD is scratched or dirty.

Try another disc instead.

The sound skips.

Remove whatever is touching it.

If skipping happens at the same place when the car is

stopped, something is wrong with the CD. Clean the CD.

The display shows that the

changer is being played, but no

sound can be heard.

The computer chip in the unit is not functioning normally.

Random play or magazine random play has been selected.

Press the reset button on the unit (see page 4).

The specified track does not

play.

Turn off the random play or magazine random play function.

If the following situations, consult your nearest service centre:

• Even though the disc changer is connected, the Disc Changer Mode is not on, with "AUX" showing in the display during the Changer Mode.

• Even though no device (KCA-S210A, CA-C1AX, KDC-CPS85, KDC-CX85, KDC-CPS82 or KDC-CX82) is connected, the AUX Mode is entered

when switching modes.

— 33 —

Troubleshooting Guide

The following messages are displayed when certain problems are occurring in your system. Take the

recommended actions.

No disc magazine has been loaded in the changer. The disc magazine is not completely loaded.

EJECT

]

Load the disc magazine properly.

No CD in the unit.

Egnlish

]

Insert the CD.

No disc has been loaded in the disc magazine.

NO DISC

E-04

]

Load a disc into the disc magazine.

No disc has been loaded in the disc magazine.

]

Load a disc into the disc magazine.

The CD is very dirty. The CD is upside-down. The CD is scratched a lot.

]

Clean the CD and load it correctly.

Nothing has been recorded on the MD.

BLANK

NO TRACK

NO PANEL

E-77

]

The next MD is automatically played back

No tracks are recorded on the MD, although it has a title.

]

The next MD is automatically played back.

The faceplate of the slave unit being connected to this unit has been removed.

]

Replace it.

The unit is malfunctioning for some reason.

]

Press the reset button on the unit. If the "E- 77", code does not disappear, consult your nearest service centre.

Something is wrong with the disc magazine. Or the unit is malfunctioning for some reason.

E-99

]

Check the disc magazine. And then, press the reset button on the unit.

If the "E- 99" code does not disappear, consult your nearest service center.

The protective circuit in the unit activates when the temperature inside the automatic disc changer exceeds 60°C (140°F),

stopping all operation.

HOLD

]

Cool down the unit by opening the windows or turning on the air conditioner. As the temperature falls below 60°C (140°F),

the disc starts playing again.

If this indicator continues blinking, it is possible that the tape has become jammed or tangled.

]

Contact the Kenwood dealer if the tape cassette cannot be ejected.

— 34 —

Specifications

Specifications subject to change without notice.

FM tuner section

Audio section

Frequency range (50 kHz Space)...............87.5 MHz – 108.0 MHz

Usable sensitivity (S/N = 26dB)..................................0.7 µV/75 Ω

Quieting Sensitivity (S/N = 46dB) ...............................1.6 µV/75 Ω

Frequency response ( 3.0 dB) ..............................30 Hz – 15 kHz

Signal to Noise ratio (MONO) ..............................................65 dB

Selectivity (DIN) ( 400 kHz)............................................. ≥ 80 dB

Stereo separation (1 kHz).....................................................35 dB

Maximum output power .................................................40 W × 4

Output power (DIN 45324, +B=14.4 V) ..........................26 W × 4

Tone action

Bass: ...........................................................100 Hz 10 dB

Treble: .........................................................10 kHz 10 dB

Preout level / load...............................................1800 mV / 10 kΩ

Preout Impedance............................................................≤ 600 Ω

MW tuner section

General

Frequency range (9 kHz Space)......................531 kHz – 1611 kHz

Usable sensitivity (S/N = 20dB)............................................25 µV

Operating voltage..............................14.4 V (11 – 16 V allowable)

Current consumption.............................................................10 A

Installation size (W × H × D) ...........................182 × 53 × 158 mm

Weight...............................................................................1400 g

LW tuner section

Frequency range..............................................153 kHz – 281 kHz

Usable sensitivity (S/N = 20dB)............................................45 µV

Cassette player section

Tape speed...............................................................4.76 cm/sec.

Wow & Flutter (WRMS).....................................................0.08 %

Frequency response .................................30 Hz – 14 kHz ( 3 dB)

Separation (1 kHz) ...............................................................43 dB

Signal to Noise ratio ............................................................54 dB

— 35 —

Roadmaster VRCD100M User Manual
Radio Shack 3Com Bigpicture User Manual
Pelco Camera Accessories PT573 User Manual
Panasonic COLOR CCTV WV CP150 User Manual
Nikon 27685 User Manual
Meyer Cable Box 8118 User Manual
Metra Electronics 99 7340B User Manual
Kodak H 1 7299T User Manual
Kenwood KDC V7017 User Manual
Kenwood AMPED XR S17P User Manual