Kenwood KDC 6047U User Manual

CD-RECEIVER  
KDC-BT60U  
KDC-6047U  
INSTRUCTION MANUAL  
The latest version of the Instruction Manual can be downloaded from www.  
kenwood.com/cs/ce/. Before reading this manual, please access this site to  
check whether your manual is the latest one.  
© 10FLIP_IM305_Ref_en_00_E  
DSP Setup  
40  
Basic Operations of remote control  
Appendix  
54  
56  
Car Type Selection  
Speaker Setting  
About Audio file  
iPod/iPhone that can be connected to this unit  
About USB device  
About “KENWOOD Music Editor”  
About the Cell-Phone  
About the Bluetooth Audio player  
Menu List  
Car Type Fine Adjustments  
X’Over Setting  
Audio Preset Memory  
Audio Preset Recall  
Favorite Control  
44  
46  
Favorite Preset Memory  
Favorite Preset Recall  
Favorite Preset Memory Delete  
Display Indicator items  
Accessories/ Installation Procedure  
Connecting Wires to Terminals  
Installation/Removing the Unit  
Troubleshooting Guide  
62  
63  
65  
67  
70  
Bluetooth Setup  
Bluetooth Setting  
Registering Bluetooth device  
Registering PIN Code  
Selecting the Bluetooth device You Wish to  
Connect  
Deleting a Registered Bluetooth device  
Downloading the Phone Book  
Specifications  
Adding a Voice Dialing Command  
Setting a Voice Command for Category  
SMS (Short Message Service)  
52  
Downloading the SMS  
SMS (Short Message Service)  
English  
|
3
Before use  
Lens Fogging  
2WARNING  
When you turn on the car heater in cold weather,  
dew or condensation may form on the lens in the  
CD player of the unit. Called lens fogging, this  
condensation on the lens may not allow CDs to play.  
In such a situation, remove the disc and wait for the  
condensation to evaporate. If the unit still does not  
operate normally after a while, consult your Kenwood  
dealer.  
To prevent injury or fire, take the following  
precautions:  
To prevent a short circuit, never put or leave any  
metallic objects (such as coins or metal tools) inside  
the unit.  
Do not use this unit before canceling  
Demonstration mode!  
This unit is initially set on the Demonstration mode.  
When using this unit for the first time, cancel the  
Demonstration mode. Refer to <Demonstration mode  
Notes  
• If you experience problems during installation,  
consult your Kenwood dealer.  
• When you purchase optional accessories, check with  
your Kenwood dealer to make sure that they work  
with your model and in your area.  
• Characters that conform to ISO 8859-1 can be  
displayed.  
How to reset your unit  
If this unit or the connected unit (auto disc changer,  
etc.) fails to operate properly, press the Reset button.  
The unit returns to factory settings when the Reset  
button is pressed.  
• Characters that conform to ISO 8859-5 or ISO 8859-1  
can be displayed. Set “Russian” of <Initial Settings>  
(page 34) to “On.  
Reset button  
• The RDS feature won’t work where the service is not  
supported by any broadcasting station.  
• In this document, the description indicator will  
light means a status is displayed. Refer to <Basic  
Operation> (page 28) for the details of the status  
display.  
• The illustrations of the display and the panel  
appearing in this manual are examples used to  
explain more clearly how the controls are used.  
Therefore, what appears on the display in the  
illustrations may differ from what appears on the  
display on the actual equipment, and some of the  
illustrations on the display may be inapplicable.  
Cleaning the Unit  
If the faceplate of this unit is stained, wipe it with a  
dry soft cloth such as a silicon cloth.  
If the faceplate is stained badly, wipe the stain off with  
a cloth moistened with neutral cleaner, then wipe it  
again with a clean soft dry cloth.  
¤
Applying spray cleaner directly to the unit may affect its  
mechanical parts. Wiping the faceplate with a hard cloth or  
using a volatile liquid such as thinner or alcohol may scratch  
the surface or erases characters.  
Unit and Faceplate Terminals  
• To prevent deterioration, do not touch the terminals  
of the unit and faceplate with your fingers.  
• If the terminals on the unit or faceplate get dirty,  
wipe them with a clean soft dry cloth.  
|
4
KDC-BT60U/ KDC-6047U  
Handling CDs  
• Do not touch the recording surface of the CD.  
• Do not stick tape etc. on the CD, or use a CD with  
tape stuck on it.  
• Do not use disc type accessories.  
• Clean from the center of the disc and move  
outward.  
• When removing CDs from this unit, pull them out  
horizontally.  
• If the CD center hole or outside rim has burrs,  
use the CD only after removing the burrs with a  
ballpoint pen etc.  
CDs that cannot be used  
• CDs that are not round cannot be used.  
• CDs with coloring on the recording surface or CDs  
that are dirty cannot be used.  
• This unit can only play the CDs with  
.
This unit may not correctly play discs which do not  
have the mark.  
• You cannot play a CD-R or CD-RW that has not  
been finalized. (For the finalization process refer to  
your CD-R/CD-RW writing software, and your CD-R/  
CD-RW recorder instruction manual.)  
• 3 inch CD cannot be used. Attempt to insert using  
an adapter can cause malfunction.  
English  
|
5
 
Component names and functions  
5
4
3
6
2
1
AUX  
14  
10  
13  
9
12  
8
11  
7
1
8
[SRC] button  
Release button  
To drop the faceplate down to open and CD can be  
inserted or ejected (press the button).  
To turn on this unit and select the Source (press the  
button).  
To turn off this unit (press the button at least 1  
second).  
2
[MENU] button  
To select a song or set functions. See <Menu List  
9
[
4
] / [¢] buttons  
To select station, song and setting items. (press the  
button).  
3
[DISP] button  
To change display item (press the button).  
[VOL] knob  
10 [38] button  
To start or interrupt playback for CD, audio file, and  
iPod. (press the button).  
To select the remove mode, and remove the USB  
device or an iPod (press the button at least 2 seconds).  
4
To adjust volume (turn the knob).  
To select menu list item (turn and press the knob). See  
KDC-BT60U : To turn on or off the traffic information  
function (press the button at least 1 second).  
KDC-6047U : To make a voice dialing call (press the  
button at least 1 second).  
11 [ ] button (KDC-BT60U)  
To enter Bluetooth mode (press the button).  
To make a voice dialing call (press the button at least  
1 second).  
5
[SEARCH MODE] button  
To enter Search mode (iPod), move between folders  
(Audio file), etc. For more details, see operations of  
each source described in page 8 or later.  
[TI] button (KDC-6047U)  
To turn on or off the traffic information function  
(press the button).  
6
Microphone (KDC-BT60U)  
To enter Bluetooth mode (press the button at least 1  
second).  
The microphone for the hands free phone is supplied.  
When your voice cannot be recognized due to the  
low microphone volume or noises in the vehicle,  
adjust the microphone settings by <Bluetooth  
12 Display window  
13 [FAV] button  
To recall a registered favorite item (press the button).  
To register to Favorite (press the button at least 1  
second).  
7
Auxiliary Input Terminal  
Portable audio device can be connected with the  
mini-plug (3.5 mm ø).  
Use the mini-plug cable which is stereo type and does not  
have any resistance.  
14 USB Terminal  
A USB device or an iPod can be connected.  
|
6
KDC-BT60U/ KDC-6047U  
General operation  
Before Using  
Menu List Operation  
The basic operating procedure for using this  
function is described below. The individual function  
items are covered in the operating procedures.  
Exit of the Demonstration Mode  
Turn off the demonstration mode when you use it  
for the first time after installation.  
1
Select the source  
1
2
Press the [VOL] knob to quit the demonstration  
mode when the messages “To Cancel Demo  
Press the Volume Knob” are displayed (approx. 15  
seconds).  
Press the [SRC] button. Turn the [VOL] knob  
and press it when the desired item is displayed.  
Function items vary from source to source. For a list  
of the function items. Refer to <Menu List> (page 58).  
SRC Select mode 2: Pressing the [SRC] button  
repeatedly switches source.  
Turn the [VOL] knob to select “YES” and press the  
[VOL] knob.  
2
3
Enter Menu List mode  
Press the [MENU] button.  
Demonstration mode can also be cancelled in “DEMO  
Mode” of Menu List mode. Refer to <Demonstration mode  
Select the setting item  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Repeat the operation until your desired setup item  
is selected.  
Common Operation  
Press the [MENU] button to return to the  
previous item.  
Operation example:  
Power and source select  
Turns the power ON by pressing the [SRC]  
button.  
When the power is ON, select a source.  
• SRC Select mode 1: Press the [SRC] button and  
then turn the [VOL] knob. To determine the  
selected source, press the [VOL] knob.  
• SRC Select mode 2: Pressing the [SRC] button  
each time switches between sources.  
Tuner (“TUNER”) Bluetooth Audio (“BT  
AUDIO”) (KDC-BT60U only) USB (“USB”)  
or iPod (“iPod”) Auxiliary input (“AUX”) ➜  
Standby (“STANDBY”) Tuner...  
4
1[VOL]  
3[MENU]  
3
2
Music  
3
2
PlayLists  
My  
Best 25  
1
1
Artists  
Albums  
[VOL]  
[MENU]  
2
4
1 sec.  
Play Mode  
In this manual, the above selection is indicated as  
Keeping pressing the [SRC] button for at least 1  
second turns the power OFF.  
Select “Music” > “Playlists” > “My Best 25.  
4
5
Make a setting  
• When the “  
” icon is displayed (at the  
PUSH  
right edge of the display)  
Turn the [VOL] knob to select a setting value,  
and then press the [VOL] knob.  
The SRC Select mode can be set in “SRC Select” of <Initial  
Auxiliary input source is initially set to “OFF. Set “Built in  
AUX” described in <Initial Settings> (page 34) to “ON.  
When an optional accessory is connected, the source name  
for each device appears.  
When connection of the iPod is recognized, the source  
display changes from “USB” to “iPod.  
This unit automatically turns full power OFF after 20  
minutes lapses in Standby mode in order to save the  
vehicle’s battery. The time until full power OFF can be set in  
“Power OFF Wait” of <Initial Settings> (page 34).  
• When the “  
” icon is not displayed  
PUSH  
Press the [4] or [¢] button to select a  
setting value.  
Exit Menu List mode  
Press the [MENU] button for at least 1 second to  
return to the first hierarchy. Press the [MENU]  
button in the first hierarchy to exit the Menu  
List mode.  
Volume  
Turning the [VOL] knob adjusts the sound  
volume.  
You cannot set the item with the “ ” icon displayed.  
English  
|
7
 
iPod/iPhone Operation  
SRC MENU VOL DISP  
SEARCH MODE  
KCA-iP101 (optional  
accessory) is required to  
connect an iPod.  
4
38  
¢
/ TI  
2
3
Enter Menu List mode  
Press the [MENU] button.  
Basic Operation  
Playing iPod  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Select “Music.  
• Connect an iPod  
When connected, the source is switched  
automatically and a song starts playing.  
4
Select a song  
• Select iPod source  
Operation type  
Move between items  
Select an item  
Operation  
Turn the [VOL] knob.  
Press the [VOL] knob.  
Press the [SRC] button. Turn the [VOL]  
knob and press it when the desired item is  
displayed.  
Select the “iPod” display.  
SRC Select mode 2: Pressing the [SRC] button  
repeatedly switches source.  
High Speed Search  
Press the [DISP] or [ ] / [TI] button to  
scroll up or down by a page.  
Press the [DISP] or [ ] / [TI] button for  
at least 1 second to continuously scroll up  
or down at high speed. Press the button  
again to stop scrolling.  
Song Select  
Press the [4] or [¢] button.  
Return to previous item  
Return to Top menu  
Press the [MENU] button.  
Press the [MENU] button for at least 1  
second.  
Fast Forwards or Fast Backwards  
Hold down the [4] or [¢] button.  
For example: Searching by Artist name.  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Select “Music” > “Artists” > Artist name > Album  
name > Song title  
Pause and Play  
Press the [38] button to pause or resume  
playback.  
Remove iPod  
Press the [38] button for at least 2 seconds.  
The unit enters the USB REMOVE mode (“USB  
REMOVE” is displayed), and the iPod can be  
removed safely.  
Cancelling Menu List mode  
Press the [MENU] button for at least 1 second,  
and then press it again briefly.  
The unit memorizes the position where you have  
found a song in the Search mode. When you enter the  
Menu List mode after searching a song, the memorized  
position is displayed. Press the [MENU] button for at least  
1 second to move to the first hierarchy, select a Menu  
item, and set it’s parameters.  
Selecting a song by browsing iPod  
Display  
Items  
“Music”  
“Playlists”  
“Artists”  
Playlists  
Artists  
Characters which cannot be displayed are left blank. If  
non of the characters can be displayed, the browse item  
name and digits are displayed.  
“Albums”  
“Songs”  
Albums  
Songs  
Items  
Playlists  
Artists  
Albums  
Songs  
Display  
“PLIST***” Podcasts  
“ART***”  
“ALB***”  
“PRGM***”  
Items  
Display  
“Podcasts”  
“Genres”  
Podcasts  
Genres  
“PDCT***”  
“GEN***”  
“COM***”  
Genres  
Composers  
“Composers”  
Composers  
1
Select iPod source  
|
8
KDC-BT60U/ KDC-6047U  
 
iPod can be operated when it conforms to the iPod  
control function.  
Play Mode  
You can select a Play Mode, such as Random play  
and Repeat play.  
iPod Setting  
1
2
Select iPod source  
You can select following iPod Setting items.  
Enter Menu List mode  
Press the [MENU] button.  
1
2
Select iPod source  
Enter Menu List mode  
Press the [MENU] button.  
3
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Select “Play Mode.  
3
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Select “Settings.  
4
Select the Play Mode  
Turn the [VOL] knob.  
4
Select the setting item  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Display  
“Play Mode”  
Overview  
“iPod by Hand” When set toON, allows you to operate iPod  
with the control on the iPod.  
“ON”/ “OFF”  
“Folder Random” When set toON, plays the music in the folder  
Display  
“Settings”  
“Skip Search”  
Overview  
Sets the ratio of skip performed with <Skip  
“0.5%”/ “1%”/ “5%”/ “10%”  
Deletes the registered My Playlist.  
(page 12) for the operation.  
randomly.  
“ON”/ “OFF”  
When set toON, plays all songs in iPod  
randomly.  
“ON”/ “OFF”  
“All Random”  
“File Repeat”  
“Delete My  
Playlist”  
When set toON, plays the music repeatedly.  
“ON”/ “OFF”  
“One”/ “All” “Yes”/ “No”  
(
: Factory setting)  
(
: Factory setting)  
5
6
Make a setting  
5
6
Make a setting  
Press the [4] or [¢] button.  
• When the “  
” icon is displayed (at the  
PUSH  
right edge of the display)  
Turn the [VOL] knob to select a setting value,  
and then press the [VOL] knob.  
Exit Menu List mode  
Press the [MENU] button for at least 1 second,  
and then press it again briefly.  
• When the “  
” icon is not displayed  
PUSH  
Press the [4] or [¢] button to select a  
setting value.  
Remarks  
• All Random  
The time required to turn on the all random function  
may become longer depending on the number of songs  
in iPod.  
Turning on the all random function changes the iPod  
browse item to “Songs. This browse item will not be  
changed even if the all random function is turned off.  
If the browse item is changed to search for music while  
the all random function is on, the all random function is  
turned off and the songs in the browse item are played  
at random.  
Exit Menu List mode  
Press the [MENU] button for at least 1 second,  
and then press it again briefly.  
The setting of “Skip Search” in <iPod Setting> (page 9)  
and that in <USB Setting> (page 15) are always the same.  
Changing the setting of one reflects the other.  
• iPod by Hand (iPod Control by Hand Mode)  
Allows you to operate iPod with the control on the iPod.  
In the iPod Control by Hand Mode, iPod cannot be  
operated using this unit.  
This mode is not compatible with music information  
display. The display will show “iPod by Hand Mode.  
English  
|
9
   
iPod/iPhone Operation  
Selecting the Search mode  
Direct Search  
You can select the most suited search method for  
the desired song from 4 types of the Search mode.  
You can quickly search the desired song by  
specifying its Search item (artist, album, etc.) and  
initial.  
Normal playing  
1
2
Select iPod source  
Display  
Overview  
Press the [SEARCH MODE] button.  
“Direct Search”  
You can quickly search the desired song by  
specifying its Search item (artist, album, etc.)  
and initial.  
3
Enter Direct Search mode  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Searches for music of the same artist or genre  
as the one being played.  
“Related Search”  
Select “Direct Search.  
Registers a song to My Playlist and play it.  
4
Select the Search item  
Turn the [VOL] knob and press it when the  
desired Search item is selected.  
“Recall My Playlist”  
“Delete My Playlist”  
“Register My P-list”  
Display  
Items  
Display  
“SONGS”  
Items  
Songs  
Browsing  
“Music”  
“PLAYLISTS” Playlists  
“PODCASTS” Podcasts  
“GENRES” Genres  
“COMPOSERS” Composers  
Display  
“Direct Search”  
Overview  
“ARTISTS”  
“ALBUMS”  
Artists  
Albums  
You can quickly search the desired song by  
specifying its Search item (artist, album, etc.)  
and initial.  
You can select an alphabetic character from  
the list in the Search item (artist, album, etc.)  
selected now.  
The number of songs to be skipped is  
determined by the ratio of the total number of  
songs in the list which is selected now.  
Registers a song to My Playlist.  
5
6
Select the character to be searched for  
“Alphabet Search”  
“Skip Search”  
Operation type  
Move between items  
Select an item  
Operation  
Turn the [VOL] knob.  
Press the [VOL] knob.  
Press the [4] or [¢] button.  
Move to the next column  
Up to 3 characters can be entered.  
Determine the selected initial  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
“Register My P-list”  
Select “DONE.  
1
Select iPod source  
Start search. When search is completed, the music  
search mode is selected again at the selected  
character position.  
After this step, you need to browse. See step 4 of  
select a song.  
Press the [SRC] button. Turn the [VOL] knob and  
press it when the desired item is displayed.  
Select the “iPod” display.  
SRC Select mode 2: Pressing the [SRC] button  
repeatedly switches source.  
2
3
4
Enter Search mode  
Press the [SEARCH MODE] button.  
Cancelling the Direct Search  
Press the [SEARCH MODE] button.  
Select the Search mode  
Turn the [VOL] knob.  
Characters that can be entered are alphabetical  
characters (A to Z), numerical characters(0 to 9), and “ * .  
“ * ” indicates characters other than alphabetical and  
numerical characters. You cannot enter any more  
characters when entering “ * ” in the first character  
position.  
Start the search mode  
Press the [VOL] knob.  
Cancelling Search mode  
Press the [SEARCH MODE ] button.  
If the first character string begins with an article “a, an,  
or “the” in the Direct Search mode, it is searched for in  
defiance of the article.  
|
10 KDC-BT60U/ KDC-6047U  
 
Related Search  
Alphabet Search  
Searches for music of the same artist or genre as the  
one being played.  
You can select a song by alphabet. This function  
searches songs whose name contain the specified  
character(s) in the list of the selected Search item  
(artist, album, etc).  
1
2
Play the music in iPod  
Press the [SEARCH MODE] button.  
1
2
Select iPod source  
3
Enter Related Search mode  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Enter browsing mode  
Press the [MENU] button.  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Select “Music” > item.  
Select “Related Search.  
4
Select the Search item  
Turn the [VOL] knob and press it when the  
desired Search item is selected.  
3
4
Enter Alphabet Search mode  
Press the [SEARCH MODE] button.  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Display  
Searches music  
“Search Artist”  
“Search Album”  
Displays the album of the same artist.  
Displays music in the album in which the one  
being played is included.  
Select “Alphabet Search.  
“Search Genre”  
Displays the artist of the same genre.  
Search for item  
“Search Composer” Displays the album including music created by the  
same Composer.  
Operation type  
Select the character  
Move between items  
Select an item  
Return to previous item  
Return to Top menu  
Operation  
Press the [DISP] or [ ] / [TI] button.  
Turn the [VOL] knob.  
Press the [VOL] knob.  
Press the [MENU] button.  
Press the [MENU] button for at least 1  
second.  
After this step, you need to browse. See step 4 of  
select a song.  
Cancelling the Related Search  
Press the [SEARCH MODE] button.  
After this step, you need to browse. See step 4 of  
select a song.  
Related search cannot be performed while playing the  
Podcast.  
Cancelling the Alphabet Search  
Press the [SEARCH MODE] button.  
When the music being played has no information on  
browsing items or no music was found, “Not Found” is  
displayed.  
The time of search by alphabet may become long  
depending on the number of songs or items in iPod.  
If the first character string begins with an article “a, an,  
or “the” in the Alphabet Search mode, it is searched for in  
defiance of the article.  
English  
|
11  
   
iPod/iPhone Operation  
Skip Search  
My Playlist  
You can scroll up or down according to the number  
of the selected Search items so that you can quickly  
switch the display position.  
Allows you to register your favorite songs in the  
Playlist of this unit. You can register up to 10 songs  
in the Playlist.  
1
2
Select iPod source  
Registering Songs in the Playlist  
Enter browsing mode  
1
2
Play the song you want to register  
Press the [MENU] button.  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Select “Music” > item.  
Press the [SEARCH MODE] button.  
3
Register the song  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
3
4
Press the [SEARCH MODE] button.  
Select “Register My Playlist”  
“## STORED (Registration number)” is displayed.  
Enter Skip Search mode  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Make a Playlist from the songs stored in one iPod. If you  
attempt to register a song stored in a different iPod,  
”No Information” appears and then ”Delete My Playlist”  
appears. Select “Yes” to delete the Playlist when you want  
to remake it.  
Select “Skip Search.  
5
Search for item  
Operation type  
Move between items  
Select an item  
Operation  
Turn the [VOL] knob.  
Press the [VOL] knob.  
Press the [DISP] or [ ] / [TI] button.  
Keep pressing the button for 3 seconds or  
longer skips songs at 10% irrespective of  
the setting.  
The song displayed in the Music Search mode can be  
registered in the same manner. For how to use the music  
search function, refer to <Selecting a song by browsing  
Skip Search  
If you attempt to register the eleventh song, ”MEMORY  
FULLappears and you cannot register it accordingly. To  
register the song, delete an unnecessary song.  
Do not register Podcasts. Songs you do not want to  
register may be registered, or playback may not be  
carried out correctly.  
Sets the ratio of skip  
performed  
Return to previous item  
Return to Top menu  
Press the [  
4] or [¢] button.  
Press the [MENU] button.  
Press the [MENU] button for at least 1  
second.  
Playing the Song in the Playlist  
After this step, you need to browse. See step 4 of  
select a song.  
1
2
Press the [SEARCH MODE] button.  
Enter My Playlist mode  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Cancelling the Skip Search  
Press the [SEARCH MODE] button.  
Select “Recall My Playlist.  
3
Play the song in the Playlist  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Set the ratio with “Skip Search” in <iPod Setting> (page  
9).  
Select the song you want to play.  
Turning ACC OFF or the power OFF cancels the My  
Playlist mode.  
The ending of a song may be cut unless the song has a  
silence of 1 second or longer at the end.  
Random play cannot be performed during playback of a  
song in the Playlist.  
Deleting a Song from the Playlist  
Press the [SEARCH MODE] button.  
1
|
12 KDC-BT60U/ KDC-6047U  
     
2
3
Enter Delete Playlist mode  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Select “Delete My Playlist.  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Select ”Delete One” or ”Delete All.  
Selecting “Delete All” moves to step 5 and all songs  
are deleted.  
4
5
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Select the song you want to delete.  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Select ”Yes.  
“Complete” is displayed.  
You can also delete all songs from the Playlist by  
selecting “Delete My Playlist” described in the section  
If you connect the different iPod from one registered to  
My Playlist, “Delete One” and “Delete All” will not appear  
and all songs be deleted.  
English  
|
13  
USB device Operation  
When connecting the  
USB device, usage of  
the CA-U1EX (option) is  
recommended.  
SEARCH MODE  
SRC MENU VOL  
DISP  
4
38  
¢
/ TI  
Basic Operation  
File Search  
Selecting the file you want to listen to from the  
device being played now.  
Playing USB device  
• Connect a USB device  
When connected, the source is switched  
automatically and a song starts playing.  
USB device  
Display  
Items  
“Music”  
Folder or file name list.  
• Select USB source  
Press the [SRC] button. Turn the [VOL]  
knob and press it when the desired item is  
displayed.  
Music Editor media  
Display  
Items  
“Music”  
Select the “USB” display.  
“Playlists”  
Playlists  
Artists  
Albums  
Songs  
SRC Select mode 2: Pressing the [SRC] button  
repeatedly switches source.  
“Artists”  
“Albums”  
“Songs”  
“Genres”  
Moving to the next folder  
Press the [SEARCH MODE] button.  
Genres  
Song Select  
Press the [4] or [¢] button.  
1
2
Select USB source  
Enter Menu List mode  
Press the [MENU] button.  
Fast Forwards or Fast Backwards  
Hold down the [4] or [¢] button.  
3
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Select “Music.  
No sound is output while playing audio file.  
Pause and Play  
Press the [38] button to pause or resume  
playback.  
4
Select a file  
Operation type  
Move between items  
Select an item  
Operation  
Turn the [VOL] knob.  
Press the [VOL] knob.  
Press the [DISP] or [ ] / [TI] button to  
scroll up or down by a page.  
Press the [DISP] or [ ] / [TI] button for  
at least 1 second to continuously scroll up  
or down at high speed. Press the button  
again to stop scrolling.  
Remove USB device  
Press the [38] button for at least 2 seconds.  
The unit enters the USB REMOVE mode (“USB  
REMOVE” is displayed), and the USB device can be  
removed safely.  
High Speed Search  
Return to previous item  
Return to Top menu  
Press the [MENU] button.  
Press the [MENU] button for at least 1  
second.  
For example: Searching for ¡".  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Select “Music” > 1 > 2 > ¡"  
|
14 KDC-BT60U/ KDC-6047U  
 
USB Setting  
1
2
You can select following USB Setting items.  
¡"  
¡#  
¡!  
1
2
Select USB source  
Enter Menu List mode  
Press the [MENU] button.  
Cancelling Menu List mode  
Press the [MENU] button for at least 1 second,  
and then press it again briefly.  
3
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Select “Settings.  
When you search a song in the File Search mode, the  
unit memorizes the position of the song being played  
after the search. To set a different Menu item after  
searching a song, press the [MENU] button for at least 1  
second to move to the first hierarchy.  
4
Select the setting item  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Display  
Overview  
“Settings”  
“Skip Search”  
Play Mode  
Sets the ratio of skip performed with <Skip  
“0.5%”/ “1%”/ “5%”/ “10%”  
You can select a Play Mode, such as Random play  
and Repeat play.  
(
: Factory setting)  
1
2
Select USB source  
5
6
Make a setting  
Press the [4] or [¢] button.  
Enter Menu List mode  
Press the [MENU] button.  
Exit Menu List mode  
Press the [MENU] button for at least 1 second,  
and then press it again briefly.  
3
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Select “Play Mode.  
4
Select the Play Mode  
Turn the [VOL] knob.  
The setting of “Skip Search” in <iPod Setting> (page 9)  
and that in <USB Setting> (page 15) are always the same.  
Changing the setting of one reflects the other.  
Display  
Overview  
“Play Mode”  
“File Scan”  
When set toON, plays the intro of the music in  
the folder successively.  
“ON”/ “OFF”  
“Folder Random” When set toON, plays the music in the folder  
randomly.  
“ON”/ “OFF”  
“File Repeat”  
When set toON, plays the music repeatedly.  
“ON”/ “OFF”  
“Folder Repeat” When set toON, plays the music in the folder  
repeatedly.  
“ON”/ “OFF”  
(
: Factory setting)  
5
6
Make a setting  
Press the [4] or [¢] button.  
Exit Menu List mode  
Press the [MENU] button for at least 1 second,  
and then press it again briefly.  
English  
|
15  
   
USB device Operation  
Function of remote control  
Skip Search  
Direct Music Search  
You can scroll up or down according to the number  
of the selected Search items so that you can quickly  
switch the display position.  
Searching the music by entering the file number.  
1
2
3
Enter Direct Music Search mode  
Press the [DIRECT] button on the remote  
control.  
1
2
Select USB source  
Enter File Search mode  
Press the [MENU] button.  
Enter the music number  
Press the number buttons on the remote  
control.  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Select “Music” > item.  
Search the music  
Press the [4] or [¢] button.  
3
4
Enter Skip Search mode  
Press the [SEARCH MODE] button.  
Cancelling Direct Music Search  
Press the [DIRECT]] button.  
Search for music  
Operation type  
Move between items  
Select an item  
Operation  
Turn the [VOL] knob.  
Press the [VOL] knob.  
Direct Music Search cannot be performed during playing  
of “Music Editor” media, Random play, or scan play.  
Skip Search  
Press the [DISP] or [ ] / [TI] button.  
Keep pressing the button for 3 seconds or  
longer skips songs at 10% irrespective of  
the setting.  
Sets the ratio of skip  
performed  
Press the [  
4] or [¢] button.  
Return to previous item  
Return to Top menu  
Press the [MENU] button.  
Press the [MENU] button for at least 1  
second.  
After this step, see step 4 of <File Search> (page 14)  
to select a song.  
Cancelling the Skip Search  
Press the [SEARCH MODE] button.  
This operation is effective only for the files registered in  
the database created with KENWOOD Music Editor.  
Set the ratio withSkip Searchin <USB Setting> (page 15).  
|
16 KDC-BT60U/ KDC-6047U  
 
Music CD/ Audio file Operation  
Fast Forwards or Fast Backwards  
Hold down the [4] or [¢] button.  
Release MENU VOL DISP  
SEARCH MODE  
No sound is output while playing audio file.  
Pause and Play  
Press the [38] button to pause or resume  
playback.  
SRC 4 38  
¢
/ TI  
Function of Internal CD source  
Basic Operation  
Music Search  
Drop open the faceplate  
Press the Release button.  
Selecting the music you want to listen to from the  
disc being played now.  
Display  
“Music”  
Overview  
Push the faceplate on the left side, and return it to its  
former position.  
Track list (Music CD) / Folder or file name list  
(Audio file)  
Disc play  
• A disc inserted.  
1
2
Select CD source  
Enter Menu List mode  
Press the [MENU] button.  
When inserted, the source is switched  
automatically and a song is starts playing.  
When a CD is inserted, the “CD-IN” indicator  
is ON.  
3
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Select “Music.  
4
Search for music  
Operation type  
Move between items  
Select an item  
Operation  
Turn the [VOL] knob.  
Press the [VOL] knob.  
High Speed Search  
Press the [DISP] or [ ] / [TI] button to  
scroll up or down by a page.  
• Select CD source  
Press the [DISP] or [ ] / [TI] button for  
at least 1 second to continuously scroll up  
or down at high speed. Press the button  
again to stop scrolling.  
Press the [MENU] button.  
Press the [MENU] button for at least 1  
second.  
Press the [SRC] button.Turn the [VOL]  
knob and press it when the desired item is  
displayed.  
Select the “CD” display.  
SRC Select mode 2: Pressing the [SRC] button  
repeatedly switches source.  
Return to previous item  
Return to Top menu  
Disc ejection  
Press the [0] button.  
Cancelling Menu List mode  
Press the [MENU] button for at least 1 second,  
and then press it again briefly.  
Moving to the next folder  
Press the [SEARCH MODE] button.  
This operation can be performed only for the Audio file.  
Song Select  
Press the [4] or [¢] button.  
English  
|
17  
 
Music CD/ Audio file Operation  
“Magazine  
Random”  
When set toON, plays the music in the disc  
changer randomly.  
“ON”/ “OFF”  
Play Mode  
You can select a Play Mode, such as Random play  
and Repeat play.  
“Track Repeat” When set toON, plays the music repeatedly.  
“ON”/ “OFF”  
When set toON, plays the music on the disc  
repeatedly.  
“ON”/ “OFF”  
1
2
Select CD source  
“Disc Repeat”  
Enter Menu List mode  
Press the [MENU] button.  
(
: Factory setting)  
3
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Select “Play Mode.  
5
6
Make a setting  
Press the [4] or [¢] button.  
4
Select the Play Mode  
Turn the [VOL] knob.  
Exit Menu List mode  
Press the [MENU] button for at least 1 second,  
and then press it again briefly.  
Music CD source  
Display  
“Play Mode”  
“Track Scan”  
Overview  
Basic Operation of Disc Changer  
(Optional)  
When set toON, plays the intro of the music on  
the disc successively.  
“ON”/ “OFF”  
Select CD changer source  
“Disc Random” When set toON, plays the music on the disc  
Press the [SRC] button. Turn the [VOL] knob and  
press it when the desired item is displayed.  
Select the “CD CHANGER” display.  
SRC Select mode 2: Pressing the [SRC] button  
repeatedly switches source.  
randomly.  
“ON”/ “OFF”  
“Track Repeat” When set toON, plays the music repeatedly.  
“ON”/ “OFF”  
(
: Factory setting)  
Moving to the next disc  
Press the [SEARCH MODE] button.  
Audio file source  
Display  
Overview  
Song Select  
Press the [4] or [¢] button.  
“Play Mode”  
“File Scan”  
When set toON, plays the intro of the music on  
the disc successively.  
Fast Forwards or Fast Backwards  
Hold down the [4] or [¢] button.  
“ON”/ “OFF”  
“Folder Random” When set toON, plays the music on the disc  
randomly.  
“ON”/ “OFF”  
When set toON, plays the music repeatedly.  
“ON”/ “OFF”  
Pause and Play  
Press the [38] button to pause or resume  
playback.  
“File Repeat”  
“Folder Repeat” When set toON, plays the music on the disc  
repeatedly.  
“ON”/ “OFF”  
(
: Factory setting)  
Disc changer source  
Display  
Overview  
“Play Mode”  
“Track Scan”  
When set toON, plays the intro of the music on  
the disc successively.  
“ON”/ “OFF”  
“Disc Random” When set toON, plays the music on the disc  
randomly.  
“ON”/ “OFF”  
|
18 KDC-BT60U/ KDC-6047U  
 
Function of remote control  
Direct Music Search  
Searching the music by entering the track number.  
1
2
3
Enter Direct Music Search mode  
Press the [DIRECT] button on the remote  
control.  
Enter the music number  
Press the number buttons on the remote  
control.  
Search the music  
Press the [4] or [¢] button.  
Cancelling Direct Music Search  
Press the [DIRECT] button.  
Direct Music Search cannot be performed during playing  
of Random play or scan play.  
Function of disc changer with remote control  
Direct Disc Search  
Searching the disc by entering the disc number.  
1
2
3
Enter Direct Disc Search mode  
Press the [DIRECT] button on the remote  
control.  
Enter the disc number  
Press the number buttons on the remote  
control.  
Search the disc  
Press the [FM] or [AM] button.  
Cancelling Direct Disc Search  
Press the [DIRECT] button.  
Direct Disc Search cannot be performed during Random  
play or scan play.  
Input “0” to select disc 10.  
English  
|
19  
 
Tuner Operation  
3
4
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Select “Settings.  
SRC MENU VOL  
SEARCH MODE  
Select the setting item to adjust  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Display  
“Settings”  
Overview  
4
¢
/ TI  
“Local Seek”  
Only stations whose reception is good are  
searched in auto seek tuning.  
“OFF”/ “ON”  
Basic Operation  
Selecting Tuner source  
“Seek Mode”  
Selects the tuning mode of the radio.  
“Auto1”: Automatic search for a station.  
“Auto2”: Search in order of the stations in the  
Preset memory.  
Press the [SRC] button. Turn the [VOL] knob and  
press it when the desired item is displayed.  
Select the “Tuner” display.  
SRC Select mode 2: Pressing the [SRC] button  
repeatedly switches source.  
“Manual”: Normal manual tuning control.  
“Auto Memory” Memorizes 6 stations with good reception  
automatically.  
“Forced MONO” Reduces the noise when stereo broadcasts are  
received as monaural.  
Selecting the Receiving Band  
Press the [SEARCH MODE] button.  
Pressing the button switches the receiving band  
(FM1, FM2, FM3, AM).  
“OFF”/ “ON”  
“News”  
Turns ON/OFF the News Bulletin Automatic  
Reception function and sets the news bulletin  
interrupt disabled time.  
Selecting the Receiving station  
Press the [4] or [¢] button.  
Details of the station selecting in operation are  
set in the “Seek mode” of <Tuner Setting> (page  
20).  
“OFF”/ “00min” – “90min”  
“AF”  
When station reception is poor, automatically  
switches to the station that is broadcasting the  
same program over the same RDS network. (AF:  
Alternative Frequency)  
Traffic information  
“OFF”/ “ON”  
KDC-BT60U  
“RDS Regional” Sets whether to switch to the station only in the  
specific region using theAFcontrol.  
“OFF”/ “ON”  
Press the [VOL] knob for at least 1 second.  
KDC-6047U  
Press the [ ] / [TI] button.  
“Auto TP Seek”  
When traffic information station reception is  
poor, automatically searches for a station that  
can be received better.  
Turns ON or OFF the Traffic Information function.  
When the function is set to ON, “TI” indicator is ON.  
If traffic bulletin starts when the function is ON,  
Traffic INFO” is displayed and traffic information is  
received.  
If the volume is adjusted during reception  
of traffic information, the adjusted volume  
is memorized automatically. The memorized  
volume will be applied next time the Traffic  
Information function is turned ON.  
“OFF”/ “ON”  
(
: Factory setting)  
5
6
Make a setting  
Press the [4] or [¢] button.  
Exit Menu List mode  
Press the [MENU] button for at least 1 second,  
and then press it again briefly.  
Remarks  
• News (News Bulletin with Timeout Setting)  
Tuner Setting  
Automatically receives news bulletin when it starts. Set  
the time during which interrupt is to be disabled after  
start of another news bulletin. Changing “News 00min”  
to “News 90min” turns this function ON. If news bulletin  
starts when this function is ON, “News” is displayed and  
news is received. If “20min” is has been set, reception of  
another news bulletin will not start for 20 minutes. The  
You can select following Tuner Setting items.  
1
2
Select Tuner source  
Enter Menu List mode  
Press the [MENU] button.  
|
20 KDC-BT60U/ KDC-6047U  
 
news bulletin volume is the same level that was set for  
Traffic Information.  
desired item is displayed.  
Select “YES.  
When 6 stations that can be received are put in the  
memory, auto memory entry closes.  
• Forced MONO  
Strong electrical fields (such as from power lines) may  
cause unstable sound quality when it is set to ON. In such  
a situation, turn it OFF.  
Preset Tuning  
Recalling the stations in the memory.  
Station Preset Memory  
1
2
Select the radio band  
Putting a station in the memory.  
Enter Menu List mode  
Press the [MENU] button.  
1
Select the radio band and tune in a desired  
radio station you wish to store in the preset  
memory  
3
Select a desired station in the memory  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
2
3
Enter Menu List mode  
Press the [MENU] button.  
Select “List & Memory” > Preset number.  
Enter Preset Memory mode  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Function of remote control  
Direct Access Tuning  
Select “List & Memory.  
Tuning in a desired radio station by entering the  
frequency.  
4
Select the number to put in the memory  
Turn the [VOL] knob and press it for at least 2  
seconds when the desired item is displayed.  
Select preset number.  
1
2
Select the radio band  
Enter Direct Access Tuning mode  
Press the [DIRECT] button on the remote  
control.  
Display  
“List & Memory”  
“-1”  
Overview  
Preset number 1.  
Preset number 2.  
“– – – –” is displayed.  
“-2”  
3
Enter the frequency  
Press the number buttons on the remote  
“-6”  
Preset number 6.  
control.  
Cancelling the Preset Memory mode  
Press the [MENU] button for at least 1 second,  
and then press it again briefly.  
Example:  
Desired frequency Press button  
92.1 MHz (FM)  
810 kHz (AM)  
[9], [2], [1]  
[8], [1], [0]  
Auto Memory Entry  
4
Tune in to the entered frequency  
Press the [4] or [¢] button.  
Putting stations with good reception in the memory  
automatically.  
Cancelling Direct Access Tuning  
Press the [DIRECT] button on the remote  
control.  
1
2
3
Select the radio band you wish to store in the  
preset memory  
Enter Menu List mode  
Press the [MENU] button.  
You can enter the FM band frequency in steps of a  
minimum of 0.1 MHz.  
Enter Auto Memory Entry mode  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Select “Settings” > “Auto Memory.  
4
Open Auto Memory Entry  
Turn the [VOL] knob and press it when the  
English  
|
21  
       
Tuner Operation  
PTY (Program Type)  
Program Type Preset  
Selecting the Program Type below and searching  
for a station.  
Putting the Program Type in the Preset button  
memory and quick recall.  
Program Type Display  
Program Type Display  
Serious Classical “Classics”  
Presetting the Program Type  
Speech  
Music  
News  
“Speech”  
“Music”  
“News”  
1
2
3
Select the Program Type to preset  
Other Music  
Weather  
Finance  
“Other M”  
“Weather”  
“Finance”  
Current Affairs  
Information  
Sport  
“Affairs”  
“Info”  
“Sport”  
Enter Program Type Preset mode  
Press the [SEARCH MODE] button.  
Children’s programs “Children”  
Social Affairs  
Religion  
Phone In  
“Social”  
Select the number to put in the memory  
Turn the [VOL] knob and press it for at least 2  
seconds when the desired item is displayed.  
Select preset number.  
Education  
Drama  
Culture  
Science  
Varied  
Pop Music  
Rock Music  
Easy Listening  
Music  
“Educate”  
“Drama”  
“Culture”  
“Science”  
“Varied”  
“Pop M”  
“Rock M”  
“Easy M”  
“Religion”  
“Phone In”  
“Travel”  
Travel  
Leisure  
“Leisure”  
“Jazz”  
“Country”  
“Nation M”  
“Oldies”  
Jazz Music  
Country Music  
National Music  
Oldies Music  
Folk Music  
Documentary  
Recalling the preset Program Type  
1
2
3
Enter PTY mode  
Enter Program Type Preset mode  
Press the [SEARCH MODE] button.  
“Folk M”  
“Document”  
Light Classical  
“Light M”  
Speech and Music include the Program type shown  
below.  
Select a desired Program Type in the memory  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Speech: Items in the white letters.  
Music: Items in the black letters.  
Select preset number.  
1
Select the FM band  
Press the [SEARCH MODE] button.  
Select “FM1, FM2, or “FM3.  
Changing Language for PTY Function  
Selecting the Program Type display language as  
follows.  
2
3
Enter Menu List mode  
Press the [MENU] button.  
Language  
English  
Spanish  
French  
Display  
“English”  
“Spanish”  
“French”  
“Dutch”  
Language  
Norwegian  
Portuguese  
Swedish  
Display  
Enter PTY mode  
“Norwegian”  
“Portuguese”  
“Swedish”  
“German”  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Select “PTY Search.  
Dutch  
German  
4
5
6
Select the Program Type  
Turn the [VOL] knob.  
1
2
3
Enter PTY mode  
Search for the selected Program Type station  
Press the [4] or [¢] button.  
Enter Changing Language mode  
Press the [VOL] button.  
Exit PTY mode  
Press the [MENU] button.  
Select the language  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Select a language.  
This function cannot be used during a traffic bulletin or  
AM reception.  
When the selected Program Type is not found, “No PTY”  
is displayed. Select another Program Type.  
The operation ends automatically if you do not operate  
within 30 seconds.  
|
22 KDC-BT60U/ KDC-6047U  
 
Function of KDC-BT60U  
KDC-6047U with KCA-BT200 (Optional Accessory)  
Bluetooth Audio Operation  
Basic Operation  
SRC MENU VOL  
Selecting Bluetooth Audio source  
Press the [SRC] button. Turn the [VOL] knob and  
press it when the desired item is displayed.  
Select the “BT Audio” display.  
SRC Select mode 2: Pressing the [SRC] button  
repeatedly switches source.  
4
38  
¢
/ TI  
Pause and play  
Press the [38] button.  
Connecting a Bluetooth Device  
Music Search  
Press the [4] or [¢] button.  
Before use the Bluetooth device, you need to  
connect Bluetooth device to this unit.  
Pairing (Registering from Bluetooth devices)  
To make your Bluetooth Audio player usable with  
this unit, you need to register it (pairing).  
All or some of the operations above cannot be  
performed if the Bluetooth audio player is not ready for  
remote control.  
1
Turn on this unit  
Press the [SRC] button.  
Switching between Bluetooth audio sources does  
not start or stop playback automatically. Perform the  
operation for starting or stopping playback.  
Some audio players cannot be controlled remotely or  
reconnected after Bluetooth disconnection. Operate the  
main unit of the audio player to connect Bluetooth.  
2
Start registering this unit by operating the  
Bluetooth device  
By operating the Bluetooth device, register the  
audio player (pairing). Select “KENWOOD BT CD/R-  
4P1”/ “KCA-BT200” from the list of connected units.  
3
4
Enter a PIN code  
Input the PIN code (“0000”) in the Bluetooth  
device.  
Check that registration is complete on the  
Bluetooth device.  
PIN code is set to “0000” as the default. You can  
change this code. Refer to <Registering PIN  
By operating the Bluetooth device, start  
Bluetooth connection.  
If pairing does not succeed, try followings.  
– PIN code is set to “0000. See <Registering PIN Code>  
– Turn off the power of this unit and turn it back on. And  
then try the pairing operation again.  
– If other audio players have been registered, delete  
them. And then try the pairing operation again. See  
When registering from this unit, refer to <Registering  
For details on the Bluetooth Audio player which can be  
English  
|
23  
Function of KDC-BT60U  
KDC-6047U with KCA-BT200 (Optional Accessory)  
Operation of hands-free phoning  
SRC MENU VOL  
SEARCH MODE  
When registering from this unit, refer to <Registering  
For details on the Bluetooth cell-phone with the hands-  
free function, see <About the Cell-Phone> (page 57).  
Receiving a Call  
4
38  
¢
/ TI  
Answering a Phone Call  
Connecting a Bluetooth Device  
Press the [VOL] knob.  
Before use the Bluetooth device, you need to  
connect Bluetooth device to this unit. The following  
3 steps procedure is necessary.  
The following operations disconnect the line:  
- Insert a CD.  
- Connect a USB device.  
Step 1. Pairing (Registering from Bluetooth  
devices)  
The name of the calling party is displayed if it has already  
been registered in the Phone Book.  
To make your Bluetooth device (cell-phone) usable  
with this unit, you need to register it (pairing).  
Rejecting an Incoming Call  
Press the [SRC] button or press the [ ] / [TI]  
button for at least 1 second.  
1
2
Turn on this unit  
Press the [SRC] button.  
Start registering a this unit by operating the  
Bluetooth device  
During a Call  
By operating the Bluetooth device, register the  
hands-free unit (pairing). Select “KENWOOD BT  
CD/R-4P1”/ “KCA-BT200” from the list of connected  
units.  
Disconnecting a Call  
Press the [SRC] button or press the [ ] / [TI]  
button for at least 1 second.  
Switching to the Private Mode  
Press the [38] knob.  
Switches between Private talk (“PRIVATE”) and  
Hands-free talk each time this button is pressed.  
3
Enter a PIN code  
Input the PIN code (“0000”) in the Bluetooth  
device.  
Check that registration is complete on the  
Bluetooth device.  
PIN code is set to “0000” as the default. You can  
change this code. Refer to <Registering PIN  
Depending on the type of your cell-phone, switching  
to the private talk mode may select the source that was  
used before commencing the hands-free connection.  
If this happens, the source cannot be switched back to  
the hands-free talk mode by operating this unit. Operate  
your cell-phone to return to the hands-free talk mode.  
4
By operating the Bluetooth device, start hands-  
free connection.  
Adjusting the Voice Volume during a Call  
Turn the [VOL] knob.  
Step 2. Connection  
If you have registered 2 or more cell-phones, you  
need to select one of them. For more details,  
Call Waiting  
When a cell-phone is connected, the “BT” indicator  
is light up.  
Answering Another Incoming Call with the  
Current Call Suspended  
Step 3. Hands-free phoning  
You can do hand-free phoning when the  
connection is made.  
1
2
Press the [VOL] knob.  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Select “ANSWER.  
|
24 KDC-BT60U/ KDC-6047U  
Answering another Incoming Call after  
Terminating the Current Call  
Press the [SRC] button.  
Press the [ ] / [TI] button.  
Speed Dialing (Preset Dial)  
Continuing the Current Call  
1
Enter Bluetooth mode  
KDC-BT60U  
1
2
Press the [VOL] knob.  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Select “REJECT.  
Press the [ ] button.  
KDC-6047U  
Press the [TI] button for at least 1 second.  
Answering the Waiting Call after Terminating  
the Current Call  
Press the [SRC] button.  
2
3
Select the preset dial mode  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Switching between the Current Call and Waiting  
Call  
Press the [VOL] knob.  
Each pressing of this knob switches the calling  
party.  
Select “Preset call.  
Select the number you want to recall from the  
memory  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Select preset number.  
Other Functions  
Phone number is displayed.  
4
5
Exit the preset dial mode  
Press the [VOL] knob.  
Clearing the Disconnection Message  
KDC-BT60U  
Press the [ ] button.  
KDC-6047U  
Make a call  
Press the [VOL] knob.  
Press the [TI] button for at least 1 second.  
“HF Disconnect” disappears.  
You need to register the preset dial number. Refer to  
Making a Call  
1
Enter Bluetooth mode  
KDC-BT60U  
Press the [ ] button.  
KDC-6047U  
Press the [TI] button for at least 1 second.  
2
Select a dialing method  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Display  
Overview  
“Preset Call”  
Calling a number in the preset.  
“Phonebook” Selecting the initial to be searched for the phone  
book.  
“In Call”  
“Out Call”  
Calling a number in the incoming call list.  
Calling a number in the outgoing call list.  
“Missed Call” Calling a number in the missed calls list.  
“Number Dial” Making a call by entering phone number.  
Operation method of each mode is described  
below.  
3
Exit the dialing method mode  
English  
|
25  
Function of KDC-BT60U  
KDC-6047U with KCA-BT200 (Optional Accessory)  
Operation of hands-free phoning  
Switching between Display Modes  
Press the [DISP] button.  
Pressing this button each time switches between  
name and telephone number.  
Calling a Number in the Phone Book  
1
Enter Bluetooth mode  
KDC-BT60U  
Press the [ ] button.  
KDC-6047U  
4
Make a call  
Press the [VOL] knob.  
Press the [TI] button for at least 1 second.  
2
3
Select the Phone Book mode  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
The outgoing call list and the incoming call list, and the  
missed call list are the lists of calls originated from and  
received at this unit. They are not the ones stored in the  
cell-phone memory.  
Select “Phonebook.  
Select the initial to be searched for  
Operation type  
Move to the next character. Turn the [VOL] knob.  
Move to the next row. Press the [ ] or [  
Operation  
Dial a Number  
1
Enter Bluetooth mode  
KDC-BT60U  
4
¢] button.  
Determine the selected initial. Press the [VOL] knob.  
Press the [ ] button.  
KDC-6047U  
4
Select the name  
Press the [TI] button for at least 1 second.  
Operation type  
Move to the next phone  
number.  
Determine the selected phone Press the [VOL] knob.  
number.  
Operation  
Turn the [VOL] knob.  
2
3
Select the number dial mode  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Select “Number Dial.  
Switching between Display Modes  
Press the [DISP] button.  
Enter a phone number  
Pressing this button each time switches between  
name and telephone number.  
Operation type  
Operation  
Turn the [VOL] knob.  
Select the numbers.  
Move to the next digit.  
Delete the last digit.  
Press the [  
Press the [  
¢
] button.  
] button.  
5
Make a call  
Press the [VOL] knob.  
4
• Press the number ([1] – [0]), #([FM]), *([AM]), or  
+([¢]) button on the remote controller.  
To erase the entered phone number digit  
by digit:  
During search, a non-accent character such as “u” is  
searched for instead of an accent character such as “ü.  
Press the [4] button on the remote  
controller.  
Calling a Number in the Call log  
1
2
3
Enter Bluetooth mode  
KDC-BT60U  
4
Make a call  
• Press the [VOL] knob.  
• Press the [DIRECT] button on the remote  
controller.  
Press the [ ] button.  
KDC-6047U  
Press the [TI] button for at least 1 second.  
You can input max 32 digits.  
Select the call log mode  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Select “Out Call(outgoing call), “In Call”  
(incoming call), or “Missed Call(missed call).  
Select a name or phone number  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
|
26 KDC-BT60U/ KDC-6047U  
     
Function of KDC-6047U  
Registering to the Preset Dial Number  
List  
Make a Voice Dialing Call  
1
Enter voice recognition mode  
Press the [VOL] button for at least 1 second.  
1
Select the phone number you wish to register  
Select the phone number with reference to the  
following:  
2
“PB Name?” is displayed.  
When a beep is heard, say the name within 2  
seconds.  
2
3
Enter Preset Memory mode  
Press the [VOL] button for at least 2 seconds.  
3
4
“PN Type” is displayed.  
When a beep is heard, say the category name  
within 2 seconds.  
Select the Preset number to put in the  
memory  
Turn the [VOL] knob and press it for at least 1  
second when the desired item is displayed.  
Select preset number.  
Make a call  
Press the [VOL] knob.  
This step is the same as step 4 of the procedure  
26). You can make a call or select a category.  
4
Determine the Preset number to put in the  
memory  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
If your voice cannot be recognized, a message is  
displayed. Pressing the [VOL] knob allows you to retry  
voice input. Refer to <Troubleshooting Guide> (page 68).  
Both the name and category require registration of  
a voice tag. Refer to <Setting a Voice Command for  
Exit the Preset Memory mode  
Press the [MENU] button.  
Audio sound is not output during voice recognition.  
Display of Phone Number type  
(category)  
The category items in the Phone Book are displayed  
as follows:  
Display  
Information  
GENERAL/“  
General  
HOME”/“  
OFFICE”/“  
MOBILE”/“  
OTHER”/“  
Home  
Office  
Mobile  
Other  
English  
|
27  
 
Display Settings  
Display Setting  
SRC MENU VOL  
You can select following Display Setting items.  
1
Select the source  
Press the [SRC] button. Turn the [VOL] knob and  
press it when the desired item is displayed.  
SRC Select mode 2: Pressing the [SRC] button  
repeatedly switches source.  
4
¢
2
3
Enter Menu List mode  
Press the [MENU] button.  
Basic Operation  
Enter Display Setting mode  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Switching display  
Press the [DISP] button.  
Mode  
Display Type  
Select “Settings” > “DISP & ILLUMI.  
5-line display mode Displays 4 to 5 lines of text.  
3-line display mode Displays 2 to 3 lines of text.  
iPod-like display Displays like iPod. (iPod source only)  
mode  
4
Select the Menu item  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Spectrum analyzer Displays a line of text and the spectrum analyzer.  
display mode  
Clock display mode Displays the clock.  
Display  
“Settings”  
Overview  
“DISP & ILLUMI” Making Display and Illumination settings.  
“Display Select” Selecting and customizing the Display type.  
“Color Select” Selecting the Illumination Color of the panel.  
•When the 5-line display mode is selected, the status (ON/OFF  
indicator of each function) can be displayed on the first line,  
and the icon of the currently selected source and the text  
information title can be displayed on the left side by the  
Status display: Select “Settings” > “DISP & ILLUMI” > “Display  
Select” > “Status”  
“Display Off  
Mode”  
If this unit is not operated at least 5 seconds  
with“OFF”selected, the display turns off. During  
a setup mode, the display will not turn off even  
if 5 seconds lapse.  
“OFF”/ “ON”  
“Display  
Dimmer”  
Reduces the display Illumination brightness.  
“Auto”: Dims the illumination in conjunction  
with the Light switch of the vehicle.  
“Manual1”: Dims the illumination constantly.  
“Manual2”: Dims the illumination darker than  
Manual1.  
Side display: Select “Settings” > “DISP & ILLUMI” > “Display  
Select” > “Side Select”  
Text scroll  
Press the [DISP] button for at least 1 second.  
The displayed text scrolls.  
“OFF”: Does not dim the illumination.  
“Contrast”  
“DISP N/P”  
Adjusting the display contrast.  
“1” - “5” - “12”  
Switches the panel display between positive  
or negative.  
“POSI1”/ “POSI2”/ “NEGA1”/ “NEGA2”  
“TEXT Scroll” Specifies whether the text is scrolled  
automatically.  
“Auto”/ “Manual”  
“ILLUMI  
Dimmer”  
Reduces the key Illumination brightness.  
“Auto”: Dims the illumination in conjunction  
with the Light switch of the vehicle.  
“Manual1”: Dims the illumination constantly.  
“Manual2”: Dims the illumination darker than  
Manual1.  
“OFF”: Does not dim the illumination.  
|
28 KDC-BT60U/ KDC-6047U  
   
“ILLUMI Effect” Sets whether the key illumination brightness is  
changed in conjunction with the key operation.  
“OFF”/ “ON”  
“ILLUMI MSC Sets whether the key illumination color is  
SYNC”  
changed in conjunction with the sound volume.  
“OFF”/ “ON”  
(
: Factory setting)  
5
6
Make a setting  
• When the “  
” icon is displayed (at the  
PUSH  
right edge of the display)  
Turn the [VOL] knob to select a setting value,  
and then press the [VOL] knob.  
• When the “  
” icon is not displayed  
PUSH  
Press the [4] or [¢] button to select a  
setting value.  
Exit Menu List mode  
Press the [MENU] button for at least 1 second,  
and then press it again briefly.  
English  
|
29  
Display Settings  
Text Display Selection  
In FM Tuner source  
Customization of 5-line Display Mode  
& 3-line Display Mode & iPod-like  
Display Mode  
Frequency & Program Service  
name (“Frequency/PS”)  
Song title* (“Song Title”)  
Artist name* (“Artist Name”)  
Station name* (“Station Name”)  
Radio text plus* (“Radio Text  
Plus”)  
Radio text (“Radio Text”)  
Spectrum analyzer & Clock  
(“Speana/Clock”)  
Date (“Date”)  
Blank (“Blank”)  
You can customize the display of the 5-line display  
mode, 3-line display mode, and iPod-like display  
mode.  
1
Select the source  
Press the [SRC] button. Turn the [VOL] knob and  
press it when the desired item is displayed.  
SRC Select mode 2: Pressing the [SRC] button  
repeatedly switches source.  
* Information of Radio text plus is displayed.  
3-line display mode  
Frequency & Program Service  
name (“Frequency/PS”)  
Song title & Artist name*  
(“Title/Artist”)  
Station name* (“Station Name”)  
Radio text plus* (“Radio Text  
Plus”)  
Radio text (“Radio Text”)  
Spectrum analyzer & Clock  
(“Speana/Clock”)  
Date (“Date”)  
2
3
Enter Menu List mode  
Press the [MENU] button.  
Blank (“Blank”)  
Enter Display Setting mode and Select the  
5-line display mode, 3-line display mode or  
iPod-like display mode.  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Select “Settings” > “DISP & ILLUMI” > “Display  
Select” > “Type Select” > 5-line display mode  
or 3-line display mode or iPod-like display  
mode.  
* Information of Radio text plus is displayed.  
In AM Tuner source  
Frequency (“Frequency”)  
Spectrum analyzer & Clock  
(“Speana/Clock”)  
Date (“Date”)  
Blank (“Blank”)  
In USB/ iPod/ Audio file source  
4
Select the setting item to adjust  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
5-line display mode  
Song title (“Song Title”)  
Album name (“Album Name”)  
Artist name (“Artist name”)  
Folder name (“Folder name”)  
File name (“File name”)  
Play time (“P-Time”)  
Play time bar (“Time Bar”) : iPod  
only  
Spectrum analyzer & Clock  
(“Speana/Clock”)  
Date (“Date”)  
Display  
Setting  
“Display Select”  
“Type Select” Selects from 5-line display mode, 3-line display  
mode, or iPod-like display mode.  
“Side Select” Sets the side display.  
Text/ Icon/ Disappear  
“Text Select” Sets the text display.  
1. Turn the [VOL] knob to select the text  
display part  
Blank (“Blank”)  
3-line display mode  
Ttitle & Artist (“Ttitle/Artist”)  
Album & Artist (“Album/Artist”)  
Folder name (“Folder name”)  
File name (“File name”)  
Play time bar (“Time Bar”) : iPod  
only  
Spectrum analyzer & Clock  
(“Speana/Clock”)  
Date (“Date”)  
The selected text display part blinks.  
2. Press the [4] or [¢] button to  
select the text  
Play time (“P-Time”)  
“Status”  
Sets the Status display of the 5-line display mode.  
Appear/ Disappear  
Blank (“Blank”)  
(
: Factory setting)  
iPod-like display mode  
5
6
Make a setting  
Press the [4] or [¢] button.  
Song title (“Song Title”)  
Album name (“Album Name”)  
Artist name (“Artist name”)  
Blank (“Blank”)  
Exit Menu List mode  
Press the [MENU] button for at least 1 second,  
and then press it again briefly.  
In Music CD source  
Disc title (“Disc title”)  
Track title (“Track title”)  
Play time (“P-Time”)  
Spectrum analyzer & Clock  
(“Speana/Clock”)  
Date (“Date”)  
Blank (“Blank”)  
|
30 KDC-BT60U/ KDC-6047U  
 
In Auxiliary input source  
Customization of Spectrum Analyzer  
Display Mode  
Source name (“Source Name”)  
Spectrum analyzer & Clock  
(“Speana/Clock”)  
Date (“Date”)  
Blank (“Blank”)  
You can customize the display of the Spectrum  
analyzer display mode.  
In Standby  
1
Select the source  
Source name (“Source Name”)  
Date (“Date”)  
Clock (“Clock”)  
Blank (“Blank”)  
Press the [SRC] button. Turn the [VOL] knob and  
press it when the desired item is displayed.  
SRC Select mode 2: Pressing the [SRC] button  
repeatedly switches source.  
In Bluetooth audio source (KDC-BT60U only)  
5-line display mode  
2
3
Enter Menu List mode  
Press the [MENU] button.  
Bluetooth audio (“Source Name”) Spectrum analyzer & Clock  
(“Speana/Clock”)  
Song title (“Song Title”)  
Date (“Date”)  
Artist name (“Artist name”)  
Enter the Display Setting mode and select the  
Spectrum analyzer display mode  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Select “Settings” > “DISP & ILLUMI” > “Display  
Select” > “Type Select” > Spectrum analyzer  
display mode.  
Blank (“Blank”)  
Album name (“Album Name”)  
3-line display mode  
Bluetooth audio (“Source Name”) Spectrum analyzer & Clock  
(“Speana/Clock”)  
Date (“Date”)  
Ttitle & Artist (“Ttitle/Artist”)  
Album & Artist (“Album/Artist”)  
Blank (“Blank”)  
4
Select the setting item to adjust  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
In Disc changer source (Optional)  
Disc title (“Disc title”)  
Track title (“Track title”)  
Play time (“P-Time”)  
Spectrum analyzer & Clock  
(“Speana/Clock”)  
Date (“Date”)  
Display  
Setting  
Blank (“Blank”)  
“Display Select”  
“Type Select” Selects the Spectrum analyzer display mode.  
“Graphic  
Select”  
Changes the display of the Spectrum analyzer  
display mode.  
If the selected display item does not have any information,  
alternative information is displayed.  
“Text Select” Sets the text display.  
Some items cannot be selected depending on the display  
type and row.  
When selecting “Folder name” while playing with iPod,  
names will be displayed depending on currently selected  
browsing items.  
5
6
Make a setting  
Press the [4] or [¢] button.  
Exit Menu List mode  
Press the [MENU] button for at least 1 second,  
and then press it again briefly.  
If the iPod Control by Hand Mode is set to on while playing  
the iPod, “iPod by Hand Mode” is displayed.  
If all characters cannot be displayed while playing with iPod,  
the file number in the list is displayed.  
Information  
Music title  
Folder name  
File name  
Display  
“TITLE***”  
“FLD***”  
“FILE***”  
English  
|
31  
 
Display Settings  
Illumination Color Selection  
Auxiliary Input Display Setting  
Selecting the Illumination Color of the panel.  
Selecting the display when changing to Auxiliary  
input source.  
1
Enter Menu List mode  
Press the [MENU] button.  
1
Select the AUX source  
Press the [SRC] button. Turn the [VOL] knob and  
press it when the desired item is displayed.  
Select the “AUX” display.  
SRC Select mode 2: Pressing the [SRC] button  
repeatedly switches source.  
2
Enter Illumination color selection mode  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Select “Settings” > “DISP & ILLUMI” > “Color  
Select.  
2
3
Enter Menu List mode  
Press the [MENU] button.  
3
4
Select the place where you want to set the  
Illumination Color  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Enter Auxiliary input display setting mode  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Place  
Display and key  
Display  
Display  
“All”  
“Display”  
“Key”  
Select “Settings” > “AUX Name Set.  
4
5
Select the Auxiliary input display  
Turn the [VOL] knob.  
Select “AUX, DVD, PORTABLE, GAME, VIDEO, or  
“TV”  
Key  
Select the Illumination Color  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Select the color from “Variable Scan”/ “Color1” —  
“Color 10”/ “User.  
Exit Menu List mode  
Press the [MENU] button for at least 1 second,  
and then press it again briefly.  
Creating “User” color  
The Auxiliary input display can be set only when the  
built-in auxiliary input or the auxiliary input of optional  
KCA-S220A is used. On the KCA-S220A, “AUX EXT” is  
displayed by default.  
You can create your original color during the  
selection from “Color1” — “Color 10.”  
The color you created can be called when you  
select “User.  
1. Press the [VOL] knob for at least 1 second.  
Enter the detail color adjustment mode.  
2. Set the color.  
AUX source is initially set to “OFF. Before display setting,  
set “Built in AUX” described in <Initial Settings> (page 34)  
to “ON.  
Operation type  
Operation  
To select the color to adjust. Press the [4] or [¢] button.  
(red, green, or blue)  
To adjust color.  
(Range: 0 – 9)  
Turn the [VOL] knob.  
3. Press the [VOL] knob.  
Exit the detail color adjustment mode.  
5
Exit Menu List mode  
Press the [MENU] button for at least 1 second,  
and then press it again briefly.  
|
32 KDC-BT60U/ KDC-6047U  
   
Clock and Other Functions  
3. Turn the [VOL] knob to adjust the day  
4. Press the [¢] button.  
5. Turn the [VOL] knob to adjust the year.  
6. Press the [VOL] knob.  
Release MENU VOL  
7
8
9
Enter Date format mode  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
SRC 4  
¢
Select “Date Mode Select.  
Select Date format  
Clock and Date Adjustment  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Select from 7 types.  
You can adjust the clock and date.  
Display  
“Settings”  
“Clock & Date”  
“Clock Adjust”  
Overview  
Exit Menu List mode  
Press the [MENU] button for at least 1 second,  
and then press it again briefly.  
Sets the clock.  
“Time Synchronize” Synchronizing the RDS station time data  
and this unit’s clock.  
“OFF”/ “ON”  
“Date Time Adjust” Sets the date.  
“Date Mode Select” Sets the date display mode.  
(
: Factory setting)  
1
2
Enter Menu List mode  
Press the [MENU] button.  
Select RDSs automatic time adjustment  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Select “Settings” > “Clock & Date” > “Time  
Synchronize” > “ON” or “OFF.  
When selected “OFF, proceed to step 3.  
When selected “ON, proceed to step 5.  
3
4
Enter Clock adjustment mode  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Select “Settings” > “Clock & Date” > “Clock  
Adjust.  
Adjusting Clock  
1. Turn the [VOL] knob to set the hours.  
2. Press the [¢] button.  
3. Turn the [VOL] knob to set the minutes.  
4. Press the [VOL] knob.  
5
6
Enter Date adjustment mode  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Select “Date Adjust.  
Adjusting Date  
1. Turn the [VOL] knob to adjust the month.  
2. Press the [¢] button.  
English  
|
33  
 
Clock and Other Functions  
“Favorite Delete” Deletes Favorite Preset Memory.  
Initial Settings  
You can select following Initial Setting items.  
“Built in AMP”  
Selecting“OFF”turns off the built-in amplifier.  
Turning off the built-in amplifier improves the  
quality of the sound from Preout.  
“OFF”/ “ON”  
DSI (Disabled System Indicator) of the unit blinks  
when the faceplate is removed.  
“OFF”/ “ON”  
1
Select the Standby  
Press the [SRC] button. Turn the [VOL] knob and  
press it when the desired item is displayed.  
Select the “STANDBY” display.  
SRC Select mode 2: Pressing the [SRC] button  
repeatedly switches source.  
“DSI”  
(
: Factory setting)  
2
3
Enter Menu List mode  
Press the [MENU] button.  
5
6
Make a setting  
• When the “  
” icon is displayed (at the  
PUSH  
Enter Initial Setting mode  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
right edge of the display)  
Turn the [VOL] knob to select a setting value,  
and then press the [VOL] knob.  
” icon is not displayed  
Press the [4] or [¢] button to select a  
Select “Initial Settings.  
• When the “  
PUSH  
4
Select the setting item to adjust  
Turn the [VOL] knob.  
setting value.  
Display  
Overview  
Exit Menu List mode  
“Initial Settings”  
“SRC Select”  
Press the [MENU] button for at least 1 second,  
and then press it again briefly.  
Sets the source selection method.  
“1”/ “2”  
“Beep”  
Setting the operation check sound (beep sound)  
ON/OFF.  
“OFF”/ “ON”  
“Russian”  
When this is set to ON, the following character  
strings are displayed in Russian:  
Folder name/ File name/ Song title/ Artist  
name/ Album name/ KCA-BT200 (optional  
accessory)  
“OFF”/ “ON”  
“Menu Language” You can select the display language for the  
Menu list item.  
“English”/ “French”/ ”Spanish”/ “German”/  
“Italian”/ “Russian”  
“Power OFF Wait” Setting the timer to turn this unit’s power OFF  
automatically when Standby mode continues.  
Using this setting can save the vehicle’s battery  
power.  
“-----”/: Power OFF Timer function is OFF.  
“20min”/ “40min”/ “60min”: Turns the power  
OFF after minutes.  
“Built in AUX”  
When this is set to ON, AUX source can be  
selected.  
“ON”: Allows AUX source to be selected. Use  
this setting when the built-in AUX terminal  
is connected to the external equipment all  
the time.  
“OFF”: Disable AUX source selection. Use this  
setting when the built-in AUX terminal is  
not used.  
“Forced CD-DA” Sets the CD read mode.  
“1”/ “2”  
|
34 KDC-BT60U/ KDC-6047U  
 
Demonstration mode Setting  
Theft Deterrent Faceplate  
Turning the demonstration mode ON/OFF.  
The faceplate of the unit can be detached and  
taken with you, helping to deter theft.  
1
Enter Menu List mode  
Press the [MENU] button.  
Removing the Faceplate  
2
Enter Demonstration mode setting  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
1
Press the Release button.  
Drop open the faceplate.  
2
Drawing the faceplate to left side pull it to  
forward and remove it.  
Select “DEMO Mode.  
3
4
Set the Demonstration mode  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Select “ON” or “OFF.  
Exit Menu List mode  
Press the [MENU] button.  
Function of KDC-6047U  
¤
Muting volume upon reception of  
Phone call  
The faceplate is a precision piece of equipment and can  
be damaged by shocks or jolts.  
Keep the faceplate in its faceplate case while detached.  
Do not expose the faceplate (and the faceplate case) to  
direct sunlight or excessive heat or humidity. Also avoid  
places with too much dust or the possibility of water  
splashing.  
The audio system automatically mutes when a call  
comes in.  
When a call comes in  
“CALLis displayed.  
The audio system pauses.  
Reattaching the Faceplate  
Listening to the audio during a call  
Press the [SRC] button.  
3
Align the shaft on the unit with the depression  
on the faceplate.  
The “CALLdisplay disappears and the audio system  
comes back ON.  
When the call ends  
Hang up the phone.  
The “CALLdisplay disappears and the audio system  
comes back ON.  
To use the TEL Mute feature, you need to hook up the MUTE  
wire to your telephone using a commercial telephone  
63).  
4
Push the faceplate in until it clicks.  
The faceplate is locked in place, allowing you to  
use the unit.  
English  
|
35  
 
Audio Adjustments  
“2Zone”  
“Preset”  
Sets the Dual Zone System.  
Sets the audio preset.  
SRC MENU VOL  
(
: Factory setting)  
1
Select the source  
Press the [SRC] button. Turn the [VOL] knob and  
press it when the desired item is displayed.  
Select a source other than “STANDBY.  
4
¢
Audio Control  
SRC Select mode 2: Pressing the [SRC] button  
repeatedly switches source.  
You can adjust following Audio Setting items.  
2
3
Enter Audio Control mode  
Press the [VOL] knob.  
Display  
“SubWoofer Level”  
Overview  
You can set subwoofer level.  
“–15” — “0” — “+15”  
“Bypass”: Disables the DSP function.  
“Through”: Enables the DSP function.  
Sets the sound quality.  
Select the setting item to adjust  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
“DSP Set”  
“Equalizer”  
Sets the Bass Boost level in two steps.  
“OFF”/ “Step1” – “2”  
Compensates the low volume or bass sound  
being lost by road noises to make vocal sound  
clearer.  
4
5
Make a setting  
Press the [4] or [¢] button to select a  
setting value, and then press the [VOL] knob.  
“Bass Boost”  
“HIGHWAY-SOUND”  
Exit Audio Control mode  
Press the [MENU] button for at least 1 second,  
and then press it again briefly.  
“OFF”/ “Step1”/ “2”/ “3”  
“Supreme+”  
“Position”  
Turns ON/OFF the Supreme plus function.  
Can be set while Music CD source, Audio file  
source of USB and iPod source.  
“ON”/ “OFF”  
Compensates the sound environment in  
accordance with the listening position.  
38).  
Adjusts left/right speaker balance.  
(Left) “L15” — “0” — “R15” (Right)  
Adjusts front/rear speaker balance.  
(Rear) “R1”5 — “0” — “F15” (Front)  
Remarks  
• DSP Set  
When “DSP Set” is set to “BYPASS, the DSP function is  
disabled , and the colored items can not be set.  
• HIGHWAY-SOUND  
Increases the volume of faintest sound being lost by road  
noises to make the sound more audible. Additionally, it  
accentuates bass sound being lost by road noises to make  
the bass sound more dynamic.  
“Balance”  
“Fader”  
• Supreme+ (Supreme Plus)  
Technology to extrapolate and supplement with  
proprietary algorithm, the high-frequency range that is cut  
off when encoding. The bass and vocal sound that are cut  
off by encoding are supplemented for the reproduction  
of natural sound quality. Supplementing is optimized by  
compression format (AAC, MP3 or WMA) and processed  
according to bit rate. The effect is negligible with music  
that is encoded at high bit rate, variable bit rate or has  
minimal high frequency range.  
“2Zone Rear Volume” Refer to <Dual Zone System> (page 39).  
“SubWoofer ON/OFF” Turns on/off the subwoofer output.  
“ON”/ “OFF”  
“Detailed Setup”  
“Car Type”  
“Speaker”  
“Car Type Adjust”  
“X'Over”  
To get clear sound, set the sound environment  
according to the location and size of physically  
installed speakers with reference to the  
followings:  
The bass and vocal sound of Music CD/ iPod is also  
supplemented.  
• Dual Zone System  
Main source and sub source (Auxiliary input) output Front  
channel and Rear channel separately.  
“Volume offset”  
Sets each source’s volume as a difference from  
the basic volume.  
“–8” — “ 0” (AUX: “-8”— “+8”)  
|
36 KDC-BT60U/ KDC-6047U  
 
Preset Equalizer curve Select  
Manual Equalizer Control  
You can select following Equalizer curve.  
You can adjust following Equalizer Control items.  
Display  
“Natural”  
“User”  
“Rock”  
“Pops”  
“Easy”  
Equalizer curve  
Natural  
User*  
Rock  
Pops  
Easy  
Top 40  
Jazz  
Band  
Item  
Range  
“BAND1”(62.5 Hz) “GAIN”Band level  
“EFCT”Bass Effect  
“BAND2”(250 Hz) “GAIN”Band level  
“BAND3”(1 kHz)  
“BAND4”(4 kHz)  
“BAND5”(16 kHz) “GAIN”Band level  
-9 –+9 dB  
“ON”/OFF”  
-9 –+9 dB  
-9 –+9 dB  
-9 –+9 dB  
-9 –+9 dB  
: Factory setting)  
“GAIN”Band level  
“GAIN”Band level  
“Top 40”  
“Jazz”  
(
“Game”  
“iPod”  
Game  
1
Select the source  
iPod (During iPod source only)  
Press the [SRC] button. Turn the [VOL] knob and  
press it when the desired item is displayed.  
Select a source other than “STANDBY.  
SRC Select mode 2: Pressing the [SRC] button  
repeatedly switches source.  
* The Equalizer curve set in the section <Manual Equalizer  
Control> is recalled.  
(
: Factory setting)  
1
Select the source  
Press the [SRC] button. Turn the [VOL] knob and  
press it when the desired item is displayed.  
Select a source other than “STANDBY.  
SRC Select mode 2: Pressing the [SRC] button  
repeatedly switches source.  
2
3
Enter Audio Control mode  
Press the [VOL] knob.  
Enter Manual Equalizer Control mode  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
2
3
Enter Audio Control mode  
Press the [VOL] knob.  
Select “Equalizer” > “Manual Equalizer.  
4
5
Select the item you want to set  
Enter Preset Equalizer mode  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Operation type  
Selects the item.  
Adjust each item.  
Set the value  
Operation  
Turn the [VOL] knob.  
Select “Equalizer” > “Preset Equalizer.  
Press the [  
Press the [VOL] button.  
4] or [¢] button.  
4
Select the Equalizer curve  
Press the [4] or [¢] button.  
Select the iPod Equalizer curve  
You can select from 22 Equalizer curve types for  
iPod when “iPod” is selected.  
1. Enter iPod Equalizer mode  
Press the [VOL] knob.  
2. Select the iPod Equalizer curve  
Press the [4] or [¢] button and press it  
when the desired item is displayed.  
Exit Audio Control mode  
Press the [MENU] button for at least 1 second,  
and then press it again briefly.  
When “iPod” is selected in the section <Preset Equalizer  
curve Select> (page 37), Manual Equalizer Control is  
disabled.  
You can select for each source.  
5
Exit Audio Control mode  
Press the [MENU] button for at least 1 second,  
and then press it again briefly.  
You can select for each source.  
English  
|
37  
   
Audio Adjustments  
Listening Position Selection  
Listening Position Fine Adjustments  
The sound environment can be compensated in  
accordance with the selected position. According to  
the listening position, select the position from the  
following settings.  
Making fine adjustment of the value specified at  
Preset position selection per speaker.  
1
Select the source  
Press the [SRC] button. Turn the [VOL] knob and  
press it when the desired item is displayed.  
Select a source other than “STANDBY.  
SRC Select mode 2: Pressing the [SRC] button  
repeatedly switches source.  
Compensation seat  
Not compensating.  
Front-Left seat  
Front-Right seat  
Front seat  
Display  
“ALL”  
“Front-Left”  
“Front-Right”  
“Front”  
2
3
Enter Audio Control mode  
Press the [VOL] knob.  
(
: Factory setting)  
1
Select the source  
Enter Manual position setting mode  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Press the [SRC] button. Turn the [VOL] knob and  
press it when the desired item is displayed.  
Select a source other than “STANDBY.  
Select “Position” > “DTA.  
SRC Select mode 2: Pressing the [SRC] button  
repeatedly switches source.  
4
Select the speaker you want to set  
Turn the [VOL] knob and press it when the  
desired value is displayed.  
2
3
Enter Audio Control mode  
Press the [VOL] knob.  
Item  
Setting overview  
Front Left speaker  
Front Right speaker  
Rear Left speaker  
Rear Right speaker  
Enter Preset position setting mode  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
“FRONT”/“L”  
“FRONT”/“R”  
“REAR”/“L”  
“REAR /R”  
Select “Position” > “Preset Position.  
“SUBWOOFER”/“LSubwoofer Left  
“SUBWOOFER”/“R” Subwoofer Right  
4
5
Select the seat you want to compensate  
Press the [4] or [¢] button.  
“INITIAL”  
Initialize the setting values.  
Exit Audio Control mode  
Press the [MENU] button for at least 1 second,  
and then press it again briefly.  
5
6
Set the value  
Press the [4] or [¢] button.  
Adjust between 0 and 170 cm.  
Press the [VOL] knob for at least 1 second if you  
want to execute the “INITIAL”.  
Exit Audio Control mode  
Press the [MENU] button for at least 1 second,  
and then press it again briefly.  
|
38 KDC-BT60U/ KDC-6047U  
   
Dual Zone System  
Main source and sub source (Auxiliary input) output  
Front channel and Rear channel separately.  
Display  
Overview  
“2Zone Rear Volume”*1 Adjust the volume of Rear channel.  
“0” — “35”  
“Detailed Setup”  
“2Zone”  
Sets the Dual Zone System.  
“OFF”/ “ON”  
Specifies the destination of sub source sound  
when the Dual Zone function is turned on.  
“Rear”/ “Front”  
“2Zone Select”*1  
*1 The Dual Zone System is set to “ON.  
(
: Factory setting)  
1
Select the source  
Press the [SRC] button. Turn the [VOL] knob and  
press it when the desired item is displayed.  
Select a source other than “STANDBY.  
SRC Select mode 2: Pressing the [SRC] button  
repeatedly switches source.  
2
3
Enter Audio Control mode  
Press the [VOL] knob.  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Select “Detailed Setup.  
4
5
Select the item you want to set  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Exit Audio Control mode  
Press the [MENU] button for at least 1 second,  
and then press it again briefly.  
Select Main source by [SRC] button.  
Adjust the volume of Front channel by [VOL] knob.  
The Audio Control has no effect on sub source.  
There are following limitations when Dual Zone System  
is enabled.  
- There is no output from the subwoofer.  
- “Fader, Subwoofer Levelof <Audio Control> (page 36)  
and DSP function are not available.  
The Bluetooth audio source can be set exclusively to the  
front speaker. Set “2Zone Select” to “Rear.  
English  
|
39  
 
DSP Setup  
Speaker Setting  
SRC MENU VOL  
The speaker X’Over is automatically set when the  
position and size of each speaker are selected from  
the following items.  
Speaker  
Item  
Range  
“Front”  
“SIZE”  
Speaker Size Front  
“O.E.M., 10cm, 13cm, 16cm,  
“17cm, 18cm, 4x6, 5x7, 6x8,  
“6x9, 7x10”  
4
¢
Car Type Selection  
“LOCATION” Speaker Location Front  
“Door, On Dash, Under Dash”  
“TWEETER” Speaker Size Tweeter  
You can compensate the delay of the sound arrival  
time by selecting your environment from the  
following car types.  
“None, Use”  
“Rear”  
“SIZE”  
Speaker Size Rear  
“None, O.E.M., 10cm, 13cm,  
“16cm, 17cm, 18cm, 4x6, 5x7,  
“6x8, 6x9, 7x10”  
Display  
“OFF”  
Overview  
Not compensating.  
Compact car  
Sedan  
Station wagon  
Minivan  
“Compact”  
“Sedan”  
“Wagon”  
“Minivan”  
“SUV”  
“LOCATION” Speaker Location Rear  
• “Door, Rear Deck”  
• “2nd Row, 3rd Row” (Car Type:  
“Minivan, Passenger Van”)  
Speaker Size Subwoofer  
“None, 16cm, 20cm, 25cm,  
“30cm, 38cm Over”  
Sport-utility vehicle  
Passenger van  
“SubWoofer” “SIZE”  
“Passenger Van”  
(
: Factory setting)  
(
: Factory setting)  
1
Select the source  
1
Select the source  
Press the [SRC] button. Turn the [VOL] knob and  
press it when the desired item is displayed.  
Select a source other than “STANDBY.  
SRC Select mode 2: Pressing the [SRC] button  
repeatedly switches source.  
Press the [SRC] button. Turn the [VOL] knob and  
press it when the desired item is displayed.  
Select a source other than “STANDBY.  
SRC Select mode 2: Pressing the [SRC] button  
repeatedly switches source.  
2
3
Enter Audio Control mode  
Press the [VOL] knob.  
2
3
Enter Audio Control mode  
Press the [VOL] knob.  
Enter Cabin select mode  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Enter Speaker setting mode  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Select “Detailed Setup” > “Car Type.  
Select “Detailed Setup” > “Speaker.  
4
5
6
Select the car type  
Press the [4] or [¢] button.  
4
5
Select the item you want to set  
Operation type  
Selects the item.  
Adjust each item.  
Set the value  
Operation  
Turn the [VOL] knob.  
Set the value  
Press the [VOL] button.  
Press the [  
Press the [VOL] button.  
4] or [¢] button.  
Exit Audio Control mode  
Press the [MENU] button for at least 1 second,  
and then press it again briefly.  
Exit Audio Control mode  
Press the [MENU] button for at least 1 second,  
and then press it again briefly.  
You can compensate the distances in more details by  
|
40 KDC-BT60U/ KDC-6047U  
   
Reference point  
Car Type Fine Adjustments  
Adjusting fine tuning of the speaker position  
compensation value specified at <Car Type  
+100cm  
FRONT  
FRONT  
REAR  
Display  
“Front”  
“Rear”  
“SW”  
Item  
Range  
50cm  
Front speaker  
Rear speaker  
Subwoofer  
0 – 440 cm  
0 – 440 cm  
0 – 440 cm  
80cm  
REAR  
+70cm  
(
: Factory setting)  
150cm  
1
Select the source  
Press the [SRC] button. Turn the [VOL] knob and  
press it when the desired item is displayed.  
Select a source other than “STANDBY.  
+0cm  
SUB-W  
SRC Select mode 2: Pressing the [SRC] button  
repeatedly switches source.  
5
Exit Audio Control mode  
2
3
Enter Audio Control mode  
Press the [VOL] knob.  
Press the [MENU] button for at least 1 second,  
and then press it again briefly.  
Enter Car Type Adjustment mode  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Select “Detailed Setup” > “Car Type Adjust.  
4
Select the item you want to set  
Operation type  
Selects the item.  
Adjust each item.  
Set the value  
Operation  
Turn the [VOL] knob.  
Press the [  
Press the [VOL] button.  
4] or [¢] button.  
The settings of the delay time are automatically  
identified and compensated by specifying the  
distances of each speaker from the center of the  
vehicle interior.  
1 Set the front and rear positions and the height  
of the reference point to the position of the ears  
of the person sitting in the front seat, and set  
the right and left positions to the center of the  
vehicle interior.  
2 Measure the distances from the reference point  
to the speakers.  
3 Calculate the distance difference in accordance  
with the farthest speaker.  
English  
|
41  
 
DSP Setup  
Press the [MENU] button for at least 1 second,  
and then press it again briefly.  
X’Over Setting  
Fine adjusting the following setting values  
corresponding to the X’Over values set in the  
Audio Preset Memory  
Registering the value setup by Sound Control.  
Display  
Item  
Range  
“X’Over”  
“Front”  
1
Setup Sound Control  
Refer to the following operations to setup the  
Sound Control.  
“FC”  
Front High Pass Filter  
Through, 30, 40, 50, 60, 70, 80, 90,  
100, 120, 150, 180, 220, 250 (Hz)  
“SLOPE” Front High Pass Slope  
-6, -12, -18, -24 dB/Oct  
“Rear”  
“FC”  
Rear High Pass Filter  
Through, 30, 40, 50, 60, 70, 80, 90,  
100, 120, 150, 180, 220, 250 (Hz)  
“SLOPE” Rear High Pass Slope  
-6, -12, -18, -24 dB/Oct  
Subwoofer Low Pass Filter  
“SubWoofer” “FC”  
30, 40, 50, 60, 70, 80, 90, 100, 120,  
150, 180, 220, 250*, Through (Hz)  
“SLOPE” Subwoofer Slope  
-6, -12, -18, -24 dB/Oct  
“PHASE” Subwoofer Phase  
Reverse (180°)/ Normal (0°)  
2
Enter Audio preset memory mode  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Select “Detailed Setup” > “Preset” > “Memory.  
3
4
Select the number to put in the memory  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
(
: Factory setting)  
1
Select the source  
Select a preset number.  
Press the [SRC] button. Turn the [VOL] knob and  
press it when the desired item is displayed.  
Select a source other than “STANDBY.  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Select “YES.  
“Memory Completed” is displayed.  
SRC Select mode 2: Pressing the [SRC] button  
repeatedly switches source.  
5
Exit Audio Control mode  
Press the [MENU] button for at least 1 second,  
and then press it again briefly.  
2
3
Enter Audio Control mode  
Press the [VOL] knob.  
Enter X’Over setting mode  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Register 6 patterns of Audio Preset Memory.  
Preset number “1”:  
Select “Detailed Setup” > “X’Over.  
When you press the Reset, all the sources will be the  
setting value which is registered.  
4
5
Select the speaker you want to set  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Preset number “1” and “2”:  
The memory cannot be erased by the Reset button.  
This function cannot be registered when the iPod  
Select “Front, Rear, or “SubWoofer.  
Select the item you want to set  
Operation type  
Selects the item.  
Adjust each item.  
Set the value  
Operation  
Turn the [VOL] knob.  
Press the [  
Press the [VOL] button.  
4] or [¢] button.  
6
7
Repeat steps 3 to 4 to complete the X’Over  
settings.  
Exit Audio Control mode  
|
42 KDC-BT60U/ KDC-6047U  
   
Audio Preset Recall  
Recalling the sound setup registered by <Audio  
1
Select the source  
Press the [SRC] button. Turn the [VOL] knob and  
press it when the desired item is displayed.  
Select a source other than “STANDBY.  
SRC Select mode 2: Pressing the [SRC] button  
repeatedly switches source.  
2
Enter Audio preset recall mode  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Select “Detailed Setup” > “Preset” > “Recall.  
3
4
Select the number to recall in the memory  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Select preset number.  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Select “YES.  
“Recall Completed” is displayed.  
5
Exit Audio Control mode  
Press the [MENU] button for at least 1 second,  
and then press it again briefly.  
changed to the value which was recalled.  
The Equalizer curve is changed to the value which was  
recalled by the selected source.  
English  
|
43  
 
Favorite Control  
If the contents in iPod are changed after the FAVORITE  
registration, the list registered in this unit becomes  
different from that in iPod. In this case, perform the  
FAVORITE registration again.  
MENU VOL  
Favorite Preset Recall  
Retrieving an item registered to Favorite.  
FAV  
1
Enter Favorite Preset Recall mode  
Press the [FAV] button.  
Favorite Preset Memory  
2
Select the number to recall in the Favorite  
memory  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Registering the operation procedure to select your  
favorite broadcast station or iPod Playlists/ Artists,  
etc.  
1
Display a favorite item  
Select preset number.  
Source  
TUNER  
iPod  
Registerable items  
Frequency  
Browse item such as Playlists/ Artists/  
Albums, etc.  
Cancelling the Favorite Preset Recall mode  
Press the [FAV] button.  
Menu list Setting  
Audio control  
Menu list Setting item  
Audio control item  
When iPod is selected for the source, the list selection  
screen for Playlists/ Artists/ Albums, etc. is displayed.  
Songs will not be automatically played.  
Hands-free phone  
Telephone number retrieval.  
” is displayed when the operation procedure  
FAV  
can be registered.  
iPod setting  
The desired list in the first hierarchy can be  
registered.  
Favorite Preset Memory Delete  
Deleting an item registered to Favorite.  
1
Select the Standby  
1st hierarchy  
2nd hierarchy  
3rd hierarchy  
Press the [SRC] button. Turn the [VOL] knob and  
press it when the desired item is displayed.  
Select the “STANDBY” display.  
iPod  
PLAYLISTS  
ALL ARTISTS  
ARTISTS 1  
ARTISTS 2  
ARTISTS 3  
ARTISTS  
ALBUMS  
SRC Select mode 2: Pressing the [SRC] button  
repeatedly switches source.  
ALL ALBUMS  
ALBUM 1  
ALBUM 2  
2
3
Enter Menu List mode  
Press the [MENU] button.  
COMPOSERS  
AUDIOBOOKS  
ALBUM 3  
Enter Favorite Preset Memory Delete mode  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
2
3
4
Enter Favorite Preset Memory mode  
Press the [FAV] button for at least 1 second.  
Select “Initial Settings” > “Favorite Delete.  
Select the number to put in the memory  
4
5
Enter Favorite Preset Memory Delete mode  
Press the [VOL] knob.  
Turn the [VOL] knob.  
Put the Favorite Preset in the memory  
Select the number you want to delete  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Press the [VOL] knob.  
Cancelling the Favorite Preset Memory mode  
Press the [FAV] button for at least 1 second.  
Select preset number.  
“Delete?” is displayed.  
Select “ALLif you want to delete all.  
Registering the operation procedure to an existing  
preset number overwrites the existing procedure.  
Register 6 of Favorite Preset Memory.  
6
Turn the [VOL] knob and press it when the  
desired item is displayed.  
The memory cannot be erased by the Reset button.  
|
44 KDC-BT60U/ KDC-6047U  
 
Select “YES.  
“Completed” is displayed.  
Exit Favorite Preset Memory Delete mode.  
English  
|
45  
Function of KDC-BT60U  
KDC-6047U with KCA-BT200 (Optional Accessory)  
Bluetooth Setup  
“Auto Answer” Answer a call automatically after lapse of the  
preset time interval for automatic answer.  
MENU VOL  
“OFF”/ “0s” – “8s” – “99s”  
“Bluetooth HF/ You can specify output speakers for hands-free  
Audio”  
voice communication and Bluetooth audio  
sound.  
“FRONT”: Outputs voice from the front  
speakers.  
“ALL”: Outputs voice from the front and rear  
speakers.  
4
38  
¢
/ TI  
“Call Beep”  
You can output a beep from the speaker when  
a call comes in.  
“ON”: Beep is heard.  
“OFF”: Beep is canceled.  
Bluetooth Setting  
You can select following Bluetooth Setting items.  
“BT F/W Update” Display the version of the firmware of this unit.  
1
Enter Bluetooth mode  
KDC-BT60U  
“Mic Gain”  
Adjust the sensitivity of the built-in microphone  
for a telephone call. Adjust the voice of caller.  
Setting to“+”increases the voice volume.  
“–3” – “0” – “+3”  
Press the [ ] button.  
KDC-6047U  
Press the [TI] button for at least 1 second.  
You can also select from “Settings” in Menu List  
mode.  
“NR Level”  
Reduce the noises generated by surrounding  
environment without changing the built-in  
microphone volume. Adjust the voice of caller  
when it is not clear. Setting to“+”increases the  
noise reduction.  
2
3
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Select “BT Settings.  
“–3” – “0” – “+3”  
“Echo Cancel LV“ Adjust the level of echo cancellation. Setting to  
“+”increases the echo cancel reduction.  
“–2” – “0” – “+2”  
Select the Menu item  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
(
: Factory setting)  
4
5
Make a setting  
• When the “  
right edge of the display)  
Turn the [VOL] knob to select a setting value,  
and then press the [VOL] knob.  
Display  
“BT Settings”  
Overview  
” icon is displayed (at the  
PUSH  
“Phone Selection” Select a cell-phone or Bluetooth audio player  
“Audio Selection”  
connection.  
• When the “  
” icon is not displayed  
PUSH  
“SMS Download” Download a short message.  
Display the received short message.  
Press the [4] or [¢] button to select a  
setting value.  
“SMS inbox”  
“Voice Tag”  
Registers voice for voice recognition and voice  
to select the Phone number category in Phone  
book.  
Exit BT Settings mode  
KDC-BT60U  
Press the [ ] button.  
KDC-6047U  
Press the [TI] button for at least 1 second.  
Remarks  
• “Auto Answer” (Setting the Time Interval for Automatic  
Answer)  
“Detailed Setup” Move to detailed item.  
“Device Regist.” Register a Bluetooth device (pairing).  
“SPCL DVC  
Select”  
“Device Delete” Cancel registration of the Bluetooth device.  
“PIN Code Edit” Specify the PIN code required when registering  
this unit using the Bluetooth device.  
This function automatically answers (responds to) a call  
after lapse of the preset time interval for automatic answer.  
“OFF” : Does not answer the phone call automatically.  
“0” : Automatically answers the phone call at once.  
“1s” – “99s” : Automatically answers the phone call after  
lapse of 1 – 99 seconds.  
If the time set in the cell-phone is shorter than that set in  
|
46 KDC-BT60U/ KDC-6047U  
 
the unit, the former will be used.  
This function does not work for call waiting.  
PIN code is correct, try <Registering Special  
• “Bluetooth HF/Audio” (Setting up the Voice Output  
Speakers)  
Select the speaker which is further from the microphone in  
order to prevent howling or echoes.  
7
8
Return to the device list  
Press the [VOL] knob.  
Exit BT Settings mode  
KDC-BT60U  
• “BT F/W Update” (Displaying the Firmware Version)  
Display the version of the firmware of this unit.  
For how to update the firmware, access our web site.  
Press the [ ] button.  
KDC-6047U  
Press the [TI] button for at least 1 second.  
Registering Bluetooth device  
This unit allows up to eight digits to be input for a PIN  
code. If a PIN code cannot be input from this unit, it can  
be input from the Bluetooth device.  
To make your Bluetooth device (cell-phone) usable  
with this unit, you need to register it (pairing). You  
can register up to 5 Bluetooth devices to this unit.  
If there are 5 or more Bluetooth devices registered, you  
cannot register a new Bluetooth device.  
Registering from this unit  
Registering Special Bluetooth device  
Allow registration of a special device that cannot be  
registered normally (pairing).  
1
Enter Bluetooth mode  
KDC-BT60U  
1. Select Special device registration mode  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Select “BT Settings” > “Detailed Setup” > “SPCL  
DVC Select.  
Press the [ ] button.  
KDC-6047U  
Press the [TI] button for at least 1 second.  
You can also select from “Settings” in Menu List  
mode.  
2. Enter Special device registration mode  
Press the [VOL] knob for at least 1 second.  
A list is displayed.  
2
Enter Bluetooth device registration mode  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Select “BT Settings” > “Detailed Setup” >  
“Device Regist.”.  
3. Select a device name  
Turn the [VOL] knob and push the center when  
the desired device name is displayed.  
If “Completed” is displayed, registration is  
completed.  
Search for the Bluetooth device.  
When search is completed, “Finished” is displayed.  
3
4
Select a Bluetooth device  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
4. Go through the procedure step 3 of  
the registration (pairing).  
Cancelling Special device registration mode  
Press the [MENU] button for at least 1 second.  
“Paring” is displayed (except KCA-BT200)  
If “Pairing Success” is displayed, proceed to step 7.  
If “PIN Code NG” is displayed, proceed to steps 5  
to 6.  
If the device name is not in the list, select “Other Phones.  
5
6
Input the PIN code  
Operation type  
Operation  
Turn the [VOL] knob.  
Select the numbers.  
Move to the next digit.  
Delete the last digit.  
Press the [  
Press the [  
¢
] button.  
] button.  
4
Transmit the PIN code  
Press the [VOL] knob for at least 1 second.  
If “Pairing Success” is displayed, registration is  
completed.  
If the error message appears even though the  
English  
|
47  
     
Function of KDC-BT60U  
KDC-6047U with KCA-BT200 (Optional Accessory)  
Bluetooth Setup  
Registering PIN Code  
Selecting the Bluetooth device You  
Wish to Connect  
By operating the Bluetooth device, specify the PIN  
code necessary for registering this unit.  
When two or more Bluetooth devices have already  
been registered, you need to select the Bluetooth  
device you wish to use.  
1
Enter Bluetooth mode  
KDC-BT60U  
Press the [ ] button.  
KDC-6047U  
1
Enter Bluetooth mode  
KDC-BT60U  
Press the [TI] button for at least 1 second.  
You can also select from “Settings” in Menu List  
mode.  
Press the [ ] button.  
KDC-6047U  
Press the [TI] button for at least 1 second.  
You can also select from “Settings” in Menu List  
mode.  
2
3
Enter PIN code edit mode  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Select “BT Settings” > “Detailed Setup” > “PIN  
Code Edit.  
The current setting of PIN code is displayed.  
2
Select Bluetooth device selection mode  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Cell-phone  
Input the PIN code  
Select “BT Settings” > “Phone Selection.  
Operation type  
Operation  
Audio player (KDC-6047U only)  
Select the numbers.  
Move to the next digit.  
Delete the last digit.  
Turn the [VOL] knob.  
Select “BT Settings” > “Audio Selection.  
Press the [  
Press the [  
¢
] button.  
] button.  
3
Enter Bluetooth device selection mode  
Press the [VOL] knob for at least 1 second.  
“(name)” is displayed.  
4
4
5
Register a PIN code  
Press the [VOL] knob for at least 1 second.  
If “Completed” is displayed, registration is  
completed.  
4
5
Select the Bluetooth device  
Turn the [VOL] knob.  
Set up the Bluetooth device  
Press the [4] or [¢] button.  
(name)” or “-(name)” is displayed.  
”: The selected Bluetooth device is busy.  
“-”: The selected Bluetooth device is on standby.  
“ “ (blank): The Bluetooth device is deselected.  
Exit BT Settings mode  
KDC-BT60U  
Press the [ ] button.  
KDC-6047U  
Press the [TI] button for at least 1 second.  
6
Exit BT Settings mode  
KDC-BT60U  
By default, “0000” is specified.  
A PIN code can be specified with up to eight digits.  
Press the [ ] button.  
KDC-6047U  
Press the [TI] button for at least 1 second.  
If a Bluetooth device is already selected, deselect it, and  
then select a different one.  
If you cannot select a device using the audio player,  
connect the device with the audio player.  
|
48 KDC-BT60U/ KDC-6047U  
   
Deleting a Registered Bluetooth  
device  
Downloading the Phone Book  
Download the phone book data from the cell-  
phone to this unit so that you can use the Phone  
Book of this unit.  
You can delete a registered Bluetooth device.  
1
Enter Bluetooth mode  
KDC-BT60U  
To download automatically  
If the cell-phone supports a phone book  
synchronization function, the phone book is  
downloaded automatically after Bluetooth  
connection.  
Press the [ ] button.  
KDC-6047U  
Press the [TI] button for at least 1 second.  
You can also select from “Settings” in Menu List  
mode.  
Setting on the cell-phone may be required.  
If no phone book data is found in the unit even after  
the compete display, your cell-phone may not support  
automatic download of phone book data. In this case, try  
downloading manually.  
2
3
Enter Bluetooth device deletion mode  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Select “BT Settings” > “Detailed Setup” >  
“Device Delete.  
To download from the cell-phone manually  
“(name)” is displayed.  
1
By operating the cell-phone, end the hands-free  
connection.  
Select the Bluetooth device  
Turn the [VOL] knob.  
2
By operating the cell-phone, send the phone  
book data to this unit  
By operating the cell-phone, download the phone  
book data to this unit.  
• During downloading:  
“Downloading” is displayed.  
4
5
Delete the selected Bluetooth device  
Press the [VOL] knob.  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Select “YES.  
“Delete” is displayed.  
• After completion of downloading:  
“Completed” is displayed.  
6
Exit BT Settings mode  
KDC-BT60U  
3
By operating the cell-phone, start the hands-  
free connection.  
Press the [ ] button.  
KDC-6047U  
To clear the downloading completion message  
Press any button.  
Press the [TI] button for at least 1 second.  
When a registered cell-phone is deleted, its Phone Book,  
log, SMS, and voice tag are also deleted.  
Up to 1000 phone numbers can be registered for each  
registered cell-phone.  
Up to 32 digits can be registered for each phone number  
along with up to 50* characters representing a name.  
(* 50: Number of alphabetic alphabetical characters.  
Fewer characters can be input depending on the type  
of characters.)  
To cancel downloading of the phone book data, operate  
the cell-phone.  
English  
|
49  
 
Function of KDC-BT60U  
KDC-6047U with KCA-BT200 (Optional Accessory)  
Bluetooth Setup  
Function of KDC-6047U  
5
Press the [VOL] knob.  
Play the registered voice and return to step 2.  
Adding a Voice Dialing Command  
Select “PB Name Delete” (Delete)  
Add a voice tag to the phone book for voice dialing.  
You can register up to 35 voice tags.  
5
Delete a voice tag  
Press the [VOL] knob.  
1
Enter Bluetooth mode  
Press the [TI] button for at least 1 second.  
You can also select from “Settings” in Menu List  
mode.  
6
Turn the [VOL] knob to select “YES, and then  
press the [VOL] knob.  
Exit BT Settings mode  
2
Enter Phone book name edit mode  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Press the [TI] button for at least 1 second.  
Audio sound is not output during voice tag registration.  
Select “BT Settings” > “Voice Tag” > “PB Name  
Edit.  
Function of KDC-6047U  
Setting a Voice Command for  
Category  
3
4
Search for the name to register  
Select the name to register with reference to 4 in  
If a voice tag has already been registered for a  
name, “*” is displayed before the name.  
Add a voice tag to the phone number category  
(type) for voice calling.  
Select a mode  
Turn the [VOL] knob.  
1
2
Enter Bluetooth mode  
Press the [TI] button for at least 1 second.  
You can also select from “Settings” in Menu List  
mode.  
Display  
Operation  
“PB Name Regist”  
“PB Name Check”*  
“PB Name Delete”*  
“Return”  
Register a voice tag.  
Play a voice tag.  
Delete a voice tag.  
Return to step 2.  
Enter Phone Number type edit mode  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
* Displayed only when a name for which a voice tag has  
been registered is selected.  
Select “BT Settings” > “Voice Tag” > “PN Type  
Edit.  
Select “PB Name Regist” (Regist)  
3
4
Select the category (type) you wish to set  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Select “General, Home, Office, Mobile, or  
“Other”  
5
Register a voice tag (first)  
“Enter Voice 1” is displayed.  
When a beep is heard, say a voice tag within 2  
seconds.  
Select a mode  
Turn the [VOL] knob.  
6
Confirm the voice tag (second)  
“Enter Voice 2” is displayed.  
When a beep is heard, say the same voice tag as  
that you said in step 6 within 2 seconds.  
“Completed” is displayed.  
Display  
Operation  
“PN Type Regist”  
“PN Type Check”*  
“PN Type Delete”*  
“Return”  
Register a voice tag.  
Play a voice tag.  
Delete a voice tag.  
Return to step 2.  
7
End registration  
Press the [VOL] knob.  
Return to step 2. You can register another voice tag  
continuously.  
* Displayed only when a name for which a voice tag has  
been registered is selected.  
5
6
Register the category (type) by performing  
If your voice cannot be recognized, a message is  
displayed. Pressing the [VOL] knob allows you to retry  
voice input. (page 52)  
Exit BT Settings mode  
Press the [TI] button for at least 1 second.  
Select “PB Name Check” (Play)  
|
50 KDC-BT60U/ KDC-6047U  
     
Set the voice tag for all the 5 categories. If the voice tag  
is not registered for all the categories, the Phone book  
may not be recalled by voice command.  
English  
|
51  
Function of KDC-BT60U  
KDC-6047U with KCA-BT200 (Optional Accessory)  
SMS (Short Message Service)  
Downloading the SMS  
SMS (Short Message Service)  
Download the short message (SMS) arrived at the  
cell-phone so that it can be read on this unit.  
The SMS arrived at the cell-phone is displayed on  
the receiver.  
A newly arrived message is displayed.  
1
Enter Bluetooth mode  
KDC-BT60U  
¤
To prevent car accidents, the driver should not read the  
SMS while driving.  
Press the [ ] button.  
KDC-6047U  
Press the [TI] button for at least 1 second.  
You can also select from “Settings” in Menu List  
mode.  
When a new message arrives  
“SMS Received” is displayed.  
The display disappears with any operations.  
2
3
Enter SMS download mode  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Displaying the SMS  
1
Enter Bluetooth mode  
KDC-BT60U  
Select “BT Settings” > “SMS Download.  
Press the [ ] button.  
KDC-6047U  
Start downloading  
Press the [VOL] knob.  
“SMS Downloading” is displayed.  
When the downloading finishes, “Completed” is  
displayed.  
Press the [TI] button for at least 1 second.  
You can also select from “Settings” in Menu List  
mode.  
2
3
4
Enter SMS Inbox mode  
Turn the [VOL] knob and press it when the  
desired item is displayed.  
Select “BT Settings” > “SMS Inbox.  
A message list appears.  
4
Exit BT Settings mode  
KDC-BT60U  
Press the [ ] button.  
KDC-6047U  
Press the [TI] button for at least 1 second.  
Select a message  
Turn the [VOL] knob.  
Each pressing of the [DISP] button switches  
between telephone number or name and message  
reception date.  
The cell-phone must be able to transmit the SMS using  
Bluetooth. Setting on the cell-phone may be required.  
If the cell-phone does not support SMS function, the  
SMS download item in Function Control mode is not  
displayed.  
Display the text  
Press the [VOL] knob.  
When the SMS is downloaded from the cell-phone, the  
unopened messages in the cell-phone are opened.  
The already-read and unread short messages can be  
respectively downloaded up to 75.  
Turning the [VOL] knob scrolls the message.  
Pressing the [VOL] knob again returns to the  
message list screen.  
5
6
Exit SMS Inbox mode  
Press the [MENU] button.  
Exit BT Settings mode  
KDC-BT60U  
Press the [ ] button.  
KDC-6047U  
Press the [TI] button for at least 1 second.  
The unopened message is displayed at the beginning  
of the list. Other messages are displayed in the order of  
reception.  
The SMS that has arrived when the cell-phone is not  
linked with Bluetooth cannot be displayed. Download  
the SMS.  
|
52 KDC-BT60U/ KDC-6047U  
   
The short message cannot be displayed during  
downloading the SMS.  
English  
|
53  
Basic Operations of remote control  
In Tuner source  
• Band select: [FM]/[AM]  
• Station select: [4]/[¢]  
• Recall preset stations: [1] — [6]  
VOL  
SRC  
ATT  
ENT  
In USB/Music CD/Audio file source  
5/∞  
• Music select: [4]/[¢]  
• Folder select: [FM]/[AM]  
• Pause/Play: [ENT]  
EXIT  
AM  
AUD  
FM  
• Enter Music search mode: [5]/[]  
• Movement between folders/files during Search  
mode: [5]/[]  
0 — 9  
• Return to previous folder: [  
]
DIRECT  
(page 16, 19, 21, 26)  
In iPod source  
• Enter Music search mode: [5]/[]  
• Movement between items during Music search  
mode: [5]/[]  
General control  
• Return to previous item: [  
]
• Music select: [4]/[¢]  
• Volume control: [VOL]  
• Source select: [SRC]  
• Volume reduce: [ATT]  
When the button is pressed again, the volume  
returns to the previous level.  
• Return to previous item: [  
• Exit from mode: [EXIT]  
• Selection of item: [5]/[]  
• Determination: [ENT]  
]
• Enter Audio Control mode: [AUD]  
|
54 KDC-BT60U/ KDC-6047U  
Hands-free phone control  
Preparing the remote control unit  
Making a call  
• Enter Bluetooth mode: [  
Pull the battery sheet out from the remote control  
unit to the direction of the arrow.  
]
• Select a dialing method: [5]/[] [ENT]  
• Number dial input:  
Input a digit: [0] – [9]  
Input “+”: [¢]  
Input “#”: [FM]  
Input “*”: [AM]  
Clear the entered phone number: [4]  
• Make a call: [DIRECT]  
Changing the battery of the remote control  
unit  
Receiving a call  
• Answer the call: [  
Keep on slide  
]
• Switch between the private talk mode and the  
hands-free talk mode: [ENT]  
CR2025  
(+side)  
Pull out  
Call waiting  
• Answer Another Incoming Call with the Current  
Use a commercially available button battery (CR2025).  
Insert the battery with the + and – poles aligned  
properly, following the illustration inside the case.  
Call Suspended: [  
]
• Answer another Incoming Call after Terminating  
the Current Call: [SRC]  
• Continue the Current Call: [1]  
During a call  
• End the call: [SRC]  
¤ CAUTION  
• Do not set the remote control in hot places such  
as on the dashboard.  
• Lithium battery.  
Danger of explosion if the battery is incorrectly  
replaced.  
Replace only with the same or equivalent type.  
• The battery pack or batteries shall not be exposed  
to excessive heat such sunshine, fire or the like.  
• Keep battery out of reach of children and in  
original package until ready to use. Dispose of  
used batteries promptly. If swallowed contact  
physician immediately.  
English  
|
55  
Appendix  
About Audio file  
iPod/iPhone that can be connected to this  
unit  
Made for  
Playable Audio file  
AAC-LC (.m4a), MP3 (.mp3), WMA (.wma)  
• iPod nano (1st generation) • iPod nano (2nd generation)  
• iPod nano (3rd generation) • iPod nano (4th generation)  
• iPod nano (5th generation) • iPod with video  
Playable disc media  
CD-R/RW/ROM  
Playable disc file format  
ISO 9660 Level 1/2, Joliet, Romeo, Long file name.  
Playable USB device  
USB mass storage class  
Playable USB device file system  
FAT16, FAT32  
• iPod classic  
• iPod touch (1st generation)  
• iPod touch (2nd generation)  
Works with  
• iPhone  
• iPhone 3G • iPhone 3GS  
Although the audio files are complied with the  
standards listed above, the play maybe impossible  
depending on the types or conditions of media or  
device.  
Playing order of the Audio file  
In the example of folder/file tree shown below, the  
files are played in the order from to .  
• Update iPod/iPhone software to the latest version.  
• Type of control available varies depending  
on the type of connected iPod. See  
^
¡
:
Folder  
CD  
(1)  
www.kenwood.com/cs/ce/ipod/ for further details.  
:
A
udiofile  
¡!  
2
• The word “iPod” appearing in this manual indicates  
the iPod or the iPhone connected with the iPod  
connection cable* (optional accessory).  
* Not supported model KCA-iP500.  
Refer to the web site for connectable iPod and iPod  
connection cable.  
3
¡"  
¡#  
4
¡$  
5
¡%  
¡P  
• If you start playback after connecting the iPod, the  
music that has been played by the iPod is played  
first.  
An online manual about audio files is put on the site,  
manual, detailed information and notes which are not  
written in this manual are provided. Make sure to read  
through the online manual as well.  
In this case, “RESUMING” is displayed without  
displaying a folder name, etc. Changing the browse  
item will display a correct title, etc.  
• You cannot operate iPod if “KENWOOD” or “”  
displayed on iPod.  
In this manual, the word “USB device” is used for flash  
memories and digital audio players which have USB  
terminals.  
About USB device  
• When the USB device is connected to this unit,  
it can be charged up provided that this unit is  
powered.  
• Install the USB device in the place where it will not  
prevent you from driving your vehicle properly.  
• You cannot connect a USB device via a USB hub and  
Multi Card Reader.  
• Take backups of the audio files used with this unit.  
The files can be erased depending on the operating  
conditions of the USB device.  
We shall have no compensation for any damage  
arising out of erasure of the stored data.  
• No USB device comes with this unit. You need to  
purchase a commercially available USB device.  
|
56 KDC-BT60U/ KDC-6047U  
 
• When connecting the USB device, usage of the  
CA-U1EX (option) is recommended.  
Normal playback is not guaranteed when a cable  
other than the USB compatible cable is used.  
Connecting a cable whose total length is longer  
than 5 m can result in abnormal playback.  
About the Bluetooth Audio player  
This unit conforms to the following Bluetooth  
specifications:  
KDC-BT60U  
Version  
Profile  
Bluetooth Standard Ver. 2.1+EDR  
A2DP (Advanced Audio Distribution Profile)  
AVRCP (Audio/Video Remote Control Profile)  
About “KENWOOD Music Editor”  
• This unit supports the PC application “KENWOOD  
Music Editor Lite ver1.0” or later.  
KDC-6047U  
Version  
Profile  
Bluetooth Standard Ver. 1.2  
A2DP (Advanced Audio Distribution Profile)  
AVRCP (Audio/Video Remote Control Profile)  
• When you use the audio file with database  
information added by the “KENWOOD Music Editor  
Lite ver1.0, you can search a file by title, album or  
artist name using the <File Search> (page 14).  
• In the Instruction manual, the term “Music Editor  
media” is used to mean the device that contains  
audio files with database information added with  
KENWOOD Music Editor.  
• “KENWOOD Music Editor Lite ver1.0” is available from  
the following web site:  
A2DP is a profile designed to transfer the music from an  
audio player.  
AVRCP is a profile designed to control playback and  
selection of music by an audio player.  
• For further information on “KENWOOD Music Editor  
Lite ver1.0, refer to the site above or the application  
help.  
About the Cell-Phone  
This unit conforms to the following Bluetooth  
specifications:  
KDC-BT60U  
Version  
Profile  
Bluetooth Standard Ver. 2.1+EDR  
HFP (Hands Free Profile)  
OPP (Object Push Profile)  
PBAP (Phone Book Access Profile)  
SYNC (Synchronization Profile)  
KDC-6047U  
You need to register your cell-phone to your  
Bluetooth Unit beforehand. Make sure to read the  
instruction manual of the Bluetooth Unit as well.  
For the cell-phones verified for compatibility, access  
the following URL:  
The units supporting the Bluetooth function have been  
certified for conformity with the Bluetooth Standard  
following the procedure prescribed by Bluetooth  
SIG. However, it may be impossible for such units to  
communicate with your cell-phone depending on its type.  
HFP is a profile used to make a hands-free call.  
OPP is a profile used to transfer data such as a phone book  
between units.  
English  
|
57  
   
Appendix  
Function items appearing when the iPod source  
is selected  
Menu List  
Common function items  
Display  
Display  
Page  
Page  
“Music”  
“Clock & Date”  
“Clock Adjust”  
“Time Synchronize”  
“Date Time Adjust”  
“Date Mode Select”  
“DISP & ILLUMI”  
“Display Select”  
“Type Select”  
“PlayLists”  
“Artists”  
“Albums”  
“Songs”  
“Podcasts”  
“Genres”  
“Composers”  
“Play Mode”  
“Side Select”  
“Text Select”  
“Graphic Select”  
“Status”  
“iPod by Hand”  
“Folder Random”  
“All Random”  
“File Repeat”  
“Color Select”  
“Settings”  
“Display Off Mode”  
“Display Dimmer”  
“Contrast”  
“DISP N/P”  
“TEXT Scroll”  
“Skip Search”  
“Delete My PlayList”  
“Clock & Date”  
“DISP & ILLUMI”  
“RDS Settings”  
“ILLUMI Dimmer”  
“ILLUMI Effect”  
“ILLUMI MSC SYNC”  
“RDS Settings”  
“News”  
Function items appearing when the USB source  
is selected  
Display  
“Music”  
Page  
“AF”  
“Play Mode”  
“RDS Regional”  
“Auto TP Seek”  
“DEMO Mode”  
“File Scan”  
“Folder Random”  
“File Repeat”  
“Folder Repeat”  
“Settings”  
Function items appearing during standby  
Display  
“Settings”  
“Clock & Date”  
“DISP & ILLUMI”  
“Initial Settings”  
“SRC Select”  
“Beep”  
Page  
“Skip Search”  
“Clock & Date”  
“DISP & ILLUMI”  
“RDS Settings”  
“Russian”  
“MENU Language”  
“Power OFF Wait”  
“Built in AUX”  
“Forced CD-DA”  
“Favorite Delete”  
“Built in AMP”  
“DSI”  
|
58 KDC-BT60U/ KDC-6047U  
 
Function items appearing when the Music CD/  
Audio file source is selected  
Function items appearing when the Hands-Free  
source is selected  
Display  
“Music”  
Page  
Display  
“Settings”  
Page  
“Play Mode”  
“Phone Selection”  
“File Scan”  
“Track Scan”  
“Folder Random”  
“Disc Random”  
“Magazine Random”  
“File Repeat”  
“Audio Selection”  
“SMS Download”  
“SMS inbox”  
“Voice Tag”  
“Detailed Setup”  
“Device Regist.”  
“Folder Repeat”  
“Track Repeat”  
“Disc Repeat”  
“SPCL DVC Select”  
“Device Delete”  
“PIN Code Edit”  
“Auto Answer”  
“Bluetooth HF/Audio”  
“Call Beep”  
“BT F/W Update”  
“Mic Gain”  
“NR Level”  
“Settings”  
“Clock & Date”  
“DISP & ILLUMI”  
“RDS Settings”  
Function items appearing when the Tuner  
source is selected  
Display  
“List & Memory”  
“FM1”  
“FM2”  
“Echo Cancel LV“  
Page  
“Clock & Date”  
“DISP & ILLUMI”  
“RDS Settings”  
Function items appearing when the Bluetooth  
Audio source is selected  
“FM3”  
“AM”  
“PTY Search”  
“Settings”  
Display  
“Settings”  
Page  
“Local Seek”  
“Seek Mode”  
“Auto Memory”  
“Forced MONO”  
“News”  
“Audio Selection”  
“Detailed Setup”  
“Device Regist.”  
“SPCL DVC Select”  
“Device Delete”  
“PIN Code Edit”  
“BT F/W Update”  
“AF”  
“RDS Regional”  
“Auto TP Seek”  
“Clock & Date”  
“DISP & ILLUMI”  
“Clock & Date”  
“DISP & ILLUMI”  
“RDS Settings”  
Function items appearing when an AUX source  
is selected  
Display  
“Settings”  
Page  
“AUX Name Set”  
“Clock & Date”  
“DISP & ILLUMI”  
“RDS Settings”  
English  
|
59  
Appendix  
Display Indicator items  
Source Display Overview  
General "ATT"  
Indicates that the attenuator is active.  
“FAV”  
iPod/USB/ “CD•IN”  
Indicates that the Favorite can be registered.  
Indicates that a disc is inserted.  
CD/CD  
Changer  
"SCAN"  
Indicates that the Scan function is ON.  
"Fi•SCAN" Indicates that the File Scan function is ON.  
“D•RDM” Indicates that the Disc Random function is ON.  
“RDM”  
Indicates that the Track/File Random function is ON.  
“Fo•RDM” Indicates that the Folder Random function is ON.  
“M•RDM” Indicates that the Magazine Random function is ON.  
“ALL•RDM” Indicates that the All Random function is ON.  
“PL•RDM” Indicates that the Playlist Random function is ON.  
“DMS•RDM” Indicates that the DMS Random function is ON.  
“DMS•REP” Indicates that the DMS Repeat function is ON.  
“D•REP” Indicates that the Disc Repeat function is ON.  
“T•REP”  
Indicates that the Track Repeat function is ON.  
“Fo•REP” Indicates that the Folder Repeat function is ON.  
“Fi•REP” Indicates that the File Repeat function is ON.  
“P•REP”  
"REP"  
“MP3”  
“WMA”  
“AAC”  
Indicates that the Playlist Repeat function is ON.  
Indicates that the Repeat function is ON.  
Identifies the MP3 file.  
Identifies the WMA file.  
Identifies the AAC-LC file.  
“MYLIST” Indicates that the My Playlist mode is selected now.  
Tuner  
“RDS”  
Indicates the state of the RDS station when the AF  
function is ON. (On: RDS is being received. Blinking: RDS  
is not being received.)  
"ST"  
"TI"  
Indicates that stereo broadcast is being received.  
Indicates the reception state of traffic information. (On: TI  
is being received. Blinking: TI is not being received.)  
Hands- “C-Wait” Indicates call-waiting.  
Free  
“PRIVATE” Indicates a cell-phone call in progress.  
"BT"  
Indicates that the Bluetooth function can be used.  
Indicates that battery level of cell-phone.  
Full  
Nearly dead  
Indicates that the battery level of cell-phone cannot be  
obtained.  
Indicates that signal strength of cell-phone.  
Maximum  
Minimum  
Indicates the out of coverage zone.  
Indicates that the signal strength of cell-phone cannot  
be obtained.  
|
60 KDC-BT60U/ KDC-6047U  
This Product is not installed by the manufacturer of a  
vehicle on the production line, nor by the professional  
importer of a vehicle into an EU Member State.  
Information on Disposal of Old Electrical  
and Electronic Equipment and Batteries  
(applicable for EU countries that have  
adopted separate waste collection systems)  
Products and batteries with the symbol  
(crossed-out wheeled bin) cannot be  
disposed as household waste.  
Old electrical and electronic equipment  
and batteries should be recycled at a facility  
capable of handling these items and their  
waste byproducts.  
Contact your local authority for details in  
locating a recycle facility nearest to you.  
Proper recycling and waste disposal will  
help conserve resources whilst preventing  
detrimental effects on our health and the  
environment.  
Notice: The sign “Pb” below the symbol for  
batteries indicates that this battery  
contains lead.  
The marking of products using lasers  
CLASS 1  
LASER PRODUCT  
The label is attached to the chassis/case and says  
that the component uses laser beams that have been  
classified as Class 1. It means that the unit is utilizing  
laser beams that are of a weaker class. There is no  
danger of hazardous radiation outside the unit.  
The “AAC” logo is trademark of Dolby Laboratories.  
The Bluetooth word mark and logos are owned by  
the Bluetooth SIG, Inc. and any use of such marks  
by Kenwood Corporation is under license. Other  
trademarks and trade names are those of their  
respective owners.  
iPod is a trademark of Apple Inc., registered in the U.S.  
and other countries.  
iPhone is a trademark of Apple Inc.  
“Made for iPod” means that an electronic accessory  
has been designed to connect specifically to iPod and  
has been certified by the developer to meet Apple  
performance standards.  
“Works with iPhone” means that an electronic  
accessory has been designed to connect specifically  
to iPhone and has been certified by the developer to  
meet Apple performance standards.  
Apple is not responsible for the operation of this  
device or its compliance with safety and regulatory  
standards.  
English  
|
61  
Accessories/ Installation Procedure  
along with the ignition). If you want to link the unit’s power  
with the ignition, connect the ignition wire to a power  
source that can be turned on and off with the ignition key.  
Use a commercially available conversion connector if the  
connector does not fit in the vehicle connector.  
Insulate unconnected wires with vinyl tape or other similar  
material. To prevent a short circuit, do not remove the caps  
on the ends of the unconnected wires or the terminals.  
If the console has a lid, make sure to install the unit so that  
the faceplate will not hit the lid when closing and opening.  
If the fuse blows, first make sure the wires aren’t touching  
to cause a short circuit, then replace the old fuse with one  
with the same rating.  
Accessories  
1
2
..........1  
..........2  
3*  
3 m ..........1  
Connect the speaker wires correctly to the terminals to  
which they correspond. The unit may be damaged or fail to  
work if you share the - wires or ground them to any metal  
part in the car.  
After the unit is installed, check whether the brake lamps,  
blinkers, wipers, etc. on the car are working properly.  
Mount the unit so that the mounting angle is 30° or less.  
Reception may drop if there are metal objects near the  
Bluetooth antenna.  
*Accessory of KDC-BT60U  
Installation Procedure  
1
To prevent short circuits, remove the key from the  
ignition and disconnect the - terminal of the  
battery.  
2
Make the proper input and output wire  
connections for each unit.  
3
4
Connect the wire on the wiring harness.  
Take Connector B on the wiring harness and  
connect it to the speaker connector in your vehicle.  
5
Take Connector A on the wiring harness and  
connect it to the external power connector on your  
vehicle.  
Connect the wiring harness connector to the unit.  
Install the unit in your car.  
Reconnect the - terminal of the battery.  
Press the reset button.  
Bluetooth antenna unit  
About CD players/disc changers connected  
to this unit  
If the CD player/ disc changer has the “O-N” switch, set  
it to the “N” position.  
The functions you can use and the information that  
can be displayed may differ depending on the models  
being connected.  
6
7
8
9
¤
Mounting and wiring this product requires skills and  
experience. For safety’s sake, leave the mounting and wiring  
work to professionals.  
For Good Reception  
To assure good reception, note the following:  
• Communicate with the cell-phone within the line-  
of-sight distance of 10 m (30 ft). The communication  
range becomes shorter depending on the  
surrounding environment. The communication  
range also becomes shorter when there is an  
obstacle between this unit and the cell-phone. The  
above maximum communication range (10 m) is  
not always assured.  
Make sure to ground the unit to a negative 12V DC power  
supply.  
Do not install the unit in a spot exposed to direct sunlight  
or excessive heat or humidity. Also avoid places with too  
much dust or the possibility of water splashing.  
Do not use your own screws. Use only the screws provided.  
If you use the wrong screws, you could damage the unit.  
If the power is not turned ON (“Protect” is displayed), the  
speaker wire may have a short-circuit or touched the  
chassis of the vehicle and the protection function may  
have been activated. Therefore, the speaker wire should be  
checked.  
• A broadcast station or walkie-talkie located nearby  
can interfere with communication due to too strong  
signal.  
Make sure that all wire connections are securely made by  
inserting jacks until they lock completely.  
If your vehicle’s ignition does not have an ACC position, or  
if the ignition wire is connected to a power source with  
constant voltage such as a battery wire, the power will not  
be linked with the ignition (i.e., it will not turn on and off  
|
62 KDC-BT60U/ KDC-6047U  
Connecting Wires to Terminals  
Do not remove the  
cap when you do not  
To USB device  
USB connector (1m)  
use the USB cable. The  
connector will cause  
the unit to malfunction  
if it gets in touch with  
any metallic part of the  
vehicle.  
Rear output  
R
L
Front output  
Sub Woofer output  
Microphone input  
(KDC-BT60U only)  
Antenna Cord  
Microphone  
(Accessory 3)  
R
L
FM/AM antenna input (JASO)  
AUX input (Stereo)  
Use the mini-plug which is stereo type  
and does not have any resistance.  
Fuse (10A)  
To Kenwood disc changer/External optional accessory  
To connect these leads, refer to the relevant instruction  
manuals.  
Wiring harness  
(Accessory 1)  
Steering remote control wire  
(Light Blue/Yellow)  
To use the steering wheel remote control feature, you  
need to an exclusive remote adapter (not supplied)  
matches your car is required.  
REMOTE CONT  
STEERING WHEEL  
REMOTE INPUT  
Mute control wire (Brown)  
Connect to the terminal that is grounded when  
either the telephone rings or during conversation.  
(KDC-6047U only)  
MUTE  
To connect the Kenwood navigation system,  
consult your navigation manual.  
If no connections are made, do not  
let the wire come out from the tab.  
Power control/Motor antenna  
control wire (Blue/White)  
P.CONT  
Connect either to the power control terminal when  
using the optional power amplifier, or to the antenna  
control terminal in the vehicle.  
ANT.CONT  
Battery wire (Yellow)  
Ignition wire (Red)  
See next page  
A–7 Pin (Red)  
A–4 Pin (Yellow)  
Connector A  
8
7
6
5
4
3
2
1
8
7
6
5
4
3
2
1
Connector B  
English  
|
63  
 
Connecting Wires to Terminals  
Connector Function Guide  
Pin Numbers for Cable Colour  
ISO Connectors  
Functions  
External Power  
Connector  
A-4  
A-5  
A-6  
A-7  
A-8  
Yellow  
Battery  
Power Control  
Dimmer  
Ignition (ACC)  
Earth (Ground)  
Connection  
Blue/White  
Orange/White  
Red  
Black  
Speaker  
Connector  
B-1  
B-2  
B-3  
B-4  
B-5  
B-6  
B-7  
Purple  
Purple/Black  
Gray  
Gray/Black  
White  
White/Black  
Green  
Rear Right (+)  
Rear Right (–)  
Front Right (+)  
Front Right (–)  
Front Left (+)  
Front Left (–)  
Rear Left (+)  
Rear Left (–)  
B-8  
Green/Black  
2WARNING  
Connecting the ISO Connector  
The pin arrangement for the ISO connectors depends on  
the type of vehicle you drive. Make sure to make the proper  
connections to prevent damage to the unit.  
The default connection for the wiring harness is described in  
1 below. If the ISO connector pins are set as described in 2,  
make the connection as illustrated.  
Please be sure to reconnect the cable as shown 2 below to  
install this unit to the Volkswagen vehicles etc.  
1(Default setting) The A-7 pin (red) of the vehicle’s  
ISO connector is linked with the ignition, and  
the A-4 pin (yellow) is connected to the constant  
power supply.  
Ignition cable (Red)  
Unit  
Battery cable (Yellow)  
A-7 Pin (Red)  
Vehicle  
A-4 Pin (Yellow)  
2The A-7 pin (red) of the vehicle’s ISO connector is  
connected to the constant power supply, and the  
A-4 pin (yellow) is linked to the ignition.  
Ignition cable  
A-7 Pin (Red)  
(Red)  
Unit  
Vehicle  
A-4 Pin (Yellow)  
Battery cable  
(Yellow)  
|
64 KDC-BT60U/ KDC-6047U  
Installation/Removing the Unit  
Installation  
Removing the hard rubber frame  
1
Engage the catch pins on the removal tool and  
remove the two locks on the upper level.  
Upper the frame and pull it forward as shown in  
the figure.  
Lock  
Catch  
Bend the tabs of the mounting  
sleeve with a screwdriver or similar  
utensil and attach it in place.  
Accessory2  
Removal tool  
Make sure that the unit is installed securely in place. If the  
unit is unstable, it may malfunction (for example, the sound  
may skip).  
2
When the upper level is removed, remove the  
lower two locations.  
The frame can be removed from the bottom side in the  
same manner.  
Removing the Unit  
1
Refer to the section <Removing the hard rubber  
frame> and then remove the hard rubber frame.  
2
3
Detach the faceplate.  
Insert the two removal tools deeply into the slots  
on each side, as shown.  
4
Lower the removal tool toward the bottom, and  
pull out the unit halfway while pressing towards  
the inside.  
Accessory2  
¤
Be careful to avoid injury from the catch pins on the  
removal tool.  
¤ CAUTION  
Install this unit in the console of your vehicle.  
Do not touch the metal part of this unit during and  
shortly after the use of the unit. Metal part such as  
the heat sink and enclosure become hot.  
5
Pull the unit all the way out with your hands, being  
careful not to drop it.  
English  
|
65  
Installation/Removing the Unit  
Accessory of KDC-BT60U  
Installation the Microphone Unit  
1
Check the installation position of the microphone  
(accessory 3).  
2
Remove oil and other dirt from the installation  
surface.  
3
4
Install the microphone.  
Wire the cable up to the unit with it secured at  
several positions using tape or the like.  
Accessory 3  
Fix a cable with a commercial  
item of tape.  
Peel the release coated paper of double-face adhesive tape to  
fix on the place shown above.  
Adjust the direction of the microphone to the driver.  
Install the microphone as far as possible from the cell-  
phone.  
|
66 KDC-BT60U/ KDC-6047U  
Troubleshooting Guide  
Some functions of this unit may be disabled by  
some settings made on this unit.  
What might seem to be a malfunction in your unit  
may just be the result of slight misoperation or  
miswiring. Before calling service, first check the  
following table for possible problems.  
!
• Cannot set up the subwoofer.  
• No output from the subwoofer.  
• Cannot set up the subwoofer position of Manual  
position setting.  
General  
? The operation check sound (beep sound) does not  
• The Dual zone function is enabled. <Dual Zone  
• In the speaker select option, None is selected for  
sound.  
The preout jack is being used.  
The Touch Sensor Tone cannot be output from  
the preout jack.  
? The illumination flashes when the knob or button  
is operated.  
!
• Cannot set up the equalizer.  
• Cannot set up the Bass Boost.  
• Cannot set up the Highway sound.  
• Cannot set up the Supreme.  
• Cannot set up the Position control.  
• The Dual zone function is enabled. <Dual Zone  
• The DSP function is disabled. “DSP Set” of <Audio  
• In the speaker select option, None is selected for  
This is the key illumination effect.  
You set this effect in “ILLUMI Effect” of <Display  
? The key illumination effect brought about in  
conjunction with the sound volume is small.  
The key illumination effect may be insufficient  
depending on the sound volume and sound quality.  
the rear speakers. <Speaker Setting> (page 40)  
Tuner source  
? Radio reception is poor.  
!
• Cannot select the output destination of the  
subsource in the Dual zone.  
• Cannot adjust the volume of the rear speakers.  
The Dual zone function is disabled. <Dual Zone  
The car antenna is not extended.  
Pull the antenna out all the way.  
Disc source  
? The specified disc does not play, but another one  
!
!
!
Cannot set up Display.  
turned off.  
plays instead.  
The specified CD is quite dirty.  
Clean the CD, referring to the CD cleaning of the  
Cannot switch to USB/iPod source.  
The Dual zone function is set to USB/iPod. <Dual  
The disc is loaded in a different slot from that  
specified.  
Eject the disc magazine and check the number  
for the specified disc.  
The disc is severely scratched.  
Try another disc instead.  
The number of songs contained in “SONGS”  
category of this unit is different from that  
contained in “SONGS” category of iPod.  
Podcast files are not counted in this unit as this unit  
does not support the playback of podcast files.  
Audio file source  
? The sound skips when an Audio file is being  
played.  
The media is scratched or dirty.  
Clean the media, referring to the CD cleaning of  
the section on <Handling CDs> (page 5).  
The recording condition is bad.  
Record the media again or use another media.  
English  
|
67  
Troubleshooting Guide  
Hands-free  
The messages shown below display your  
systems condition.  
? The hands-free talk volume is low.  
The hands-free talk volume is set at a low level.  
TOC Error:  
• No disc has been loaded in the disc  
magazine.  
The hands-free talk volume can be adjusted  
independently. Adjust it during hands-free talk.  
“Mic Gain” and “NR Level” <Bluetooth Setting>  
• The CD is quite dirty. The CD is upside-  
down. The CD is scratched a lot.  
ERROR 05:  
The disc is unreadable.  
? No sound is heard from the rear speakers.  
You are talking in the hand-free talk mode.  
ERROR 77/Mecha Error:  
The unit is malfunctioning for some reason.  
No sound is heard from the rear speakers in the  
hands-free talk mode.  
Press the reset button on the unit. If the  
“ERROR 77”/“Mecha Error” code does not  
disappear, consult your nearest service  
center.  
? No beep is heard at reception of an incoming call.  
No beep is heard depending on the type of your  
cell-phone.  
ERROR 99:  
Something is wrong with the disc magazine.  
Or the unit is malfunctioning for some reason.  
Check the disc magazine. And then press  
the reset button on the unit. If the “ERROR  
99” code does not disappear, consult your  
nearest service center.  
TheCall Beepof <Bluetooth Setting> (page 46) is  
set ON.  
? Voice is not recognized.  
The vehicle window is open.  
If the surrounding noise is large, voice cannot be  
recognized properly. Close the vehicle windows  
to reduce noise.  
CD-IN (Blink): The CD player section is not operating  
properly.  
Small voice.  
If voice is too small, it cannot be recognized  
Reinsert the CD. If the CD cannot be  
ejected or the display continues to flash  
even when the CD has been properly  
reinserted, please switch off the power  
and consult your nearest service center.  
properly. Speak into the microphone a little more  
loudly and naturally.  
The person uttering the voice tag is not the one who  
registered the it.  
Only the voice of the person who registered the  
voice tag can be recognized.  
Protect (Blink):  
The speaker wire has a short-circuit or  
touches the chassis of the vehicle, and then  
the protection function is activated.  
Wire or insulate the speaker cable properly  
and press the reset button. If the “Protect”  
code does not disappear, consult your  
nearest service center.  
Bluetooth audio source  
? The Bluetooth audio player cannot be registered  
(pairing).  
The PIN code is fixed.  
When a PIN code is specified in the Instruction  
Manual for Bluetooth Audio Player, register it  
48) to register the Bluetooth audio player. If no PIN  
code is specified in the Instruction Manual, try  
“0000.  
Unsupported File:  
An Audio file is played with a format that this  
unit can’t support.  
Copy Protection:  
A copy-protected file is played.  
Read Error:  
No Device:  
The file system of the connected USB device  
is broken.  
Copy the files and folders for the USB  
device again. If the error message is still  
displayed, initialize the USB device or use  
other USB devices.  
? The sound from the Bluetooth audio player is  
discontinuous.  
The distance between this unit and audio player is  
too far.  
Move the audio player nearer to this unit.  
Another Bluetooth device is affecting the Bluetooth  
communication.  
The USB device is selected as a source  
although no USB device is connected.  
Change the source to any source other  
than USB. Connect an USB device, and  
change the source to USB again.  
Turn off another Bluetooth device.  
Move another Bluetooth device away from this  
unit.  
Another Bluetooth device or profile is used for  
communication.  
The downloading of the Phone book or the SMS  
disconnects the sound.  
|
68 KDC-BT60U/ KDC-6047U  
 
N/A Device:  
• An unsupported USB device is connected.  
• Connection to the iPod has failed.  
Check that the connected iPod is an iPod  
that is supported. See <About Audio file>  
(page 56) for information on supported  
iPods.  
Err No Matching:  
The voice tag is wrong. Voice cannot be  
recognized because of an unregistered voice  
tag, etc.  
Too Soft:  
Too Loud:  
Too Long:  
Voice is too small and cannot be recognized.  
Voice is too large to be recognized.  
No Music Data/Error 15:  
• The connected USB device contains no  
The word or utterance is too long to be  
recognized.  
playable audio file.  
• Media was played that does not have data  
recorded that the unit can play.  
No Phonebook: Data is not contained in the phone book.  
No Message: No short message in In Box.  
USB ERROR:  
iPod Error:  
Some trouble may have occurred to the  
connected USB device.  
Remove the USB device, then cycle the  
power switch to ON. If the same display is  
repeated, use another USB device.  
No Record:  
The voice tag is not registered in the phone  
book.  
Memory Full: The number of voice tags reaches the  
maximum number to be registered in the  
phone book.  
Connection to the iPod has failed.  
Remove the USB device and then  
reconnect it.  
Confirm that the software for the iPod is  
the latest version.  
Favorite: No Memory:  
The procedure is not registered to Favorite  
Preset Memory  
USB REMOVE (Blink):  
The Remove mode has been selected for the  
No Access:  
No Voice:  
The procedure preset with Favorite Control  
cannot be available. The preset content may  
not be recalled depending on the selected  
source or mode.  
USB device/iPod. You can remove the USB  
device/iPod safely.  
No Number:  
No Data:  
• The calling party does not notify a caller ID.  
• There is no phone number data.  
No call.  
• There is no outgoing call list.  
• There is no incoming call list.  
• There is no missed call list.  
• There is no phone book list.  
No Entry:  
The cell-phone has not been registered  
(pairing).  
HF Disconnect: The unit cannot communicate with the cell-  
phone.  
HF Error 07:  
The memory cannot be accessed.  
Turn off the power and on again. If this  
message still appears, press the reset  
button on the control unit.  
HF Error 68:  
The unit cannot communicate with the cell-  
phone.  
Turn off the power and on again. If this  
message still appears, press the reset  
button on the control unit.  
Un Known:  
Device Full:  
The Bluetooth device cannot be detected.  
5 Bluetooth device have already been  
registered. No more Bluetooth device cannot  
be registered.  
PIN Code NG: The PIN code is wrong.  
Connect NG: The unit cannot be connected to the device.  
Pairing Failed: Pairing error.  
English  
|
69  
Specifications  
FM tuner section  
USB Interface  
Frequency range (50 kHz space)  
: 87.5 MHz – 108.0 MHz  
USB Standard  
: USB1.1/ 2.0 (Full speed)  
Usable sensitivity (S/N = 26dB)  
: 0.7 μV/75 Ω  
Maximum Supply current  
: 500 mA  
Quieting Sensitivity (S/N = 46dB)  
: 1.6 μV/75 Ω  
File System  
: FAT16/ 32  
Frequency response ( 3.0 dB)  
: 30 Hz – 15 kHz  
MP3 decode  
: Compliant with MPEG-1/2 Audio Layer-3  
Signal to Noise ratio (MONO)  
: 65 dB  
WMA decode  
: Compliant with Windows Media Audio  
Selectivity (DIN) ( 400 kHz)  
: ≥ 80 dB  
AAC decode  
: AAC-LC .m4a” files  
Stereo separation (1 kHz)  
: 35 dB  
CD player section  
Laser diode  
: GaAlAs  
MW tuner section  
Frequency range (9 kHz space)  
: 531 kHz – 1611 kHz  
Digital filter (D/A)  
: 8 Times Over Sampling  
Usable sensitivity (S/N = 20dB)  
: 25 µV  
D/A Converter  
: 24 Bit  
Spindle speed  
: 500 – 200 rpm (CLV)  
Wow & Flutter  
: Below Measurable Limit  
Frequency response ( 1 dB)  
: 10 Hz – 20 kHz  
Total harmonic distortion (1 kHz)  
: 0.008 %  
Signal to Noise ratio (1 kHz)  
: 110 dB  
Dynamic range  
: 93 dB  
MP3 decode  
: Compliant with MPEG-1/2 Audio Layer-3  
WMA decode  
: Compliant with Windows Media Audio  
AAC decode  
: AAC-LC .m4a” files  
LW tuner section  
Frequency range  
: 153 kHz – 279 kHz  
Usable sensitivity (S/N = 20dB)  
: 45 µV  
Bluetooth section (KDC-BT60U)  
Version  
: Bluetooth Ver.2.1+EDR Certified  
Frequency range  
: 2.402 – 2.480 GHz  
Output Power  
: +4dBm (MAX), 0dBm (AVE) Power Class 2  
Maximum Communication range  
: Line of sight approx.10m (32.8 ft)  
Profiles  
: HFP (Hands Free Profile)  
: HSP (Headset Profile)  
: SPP (Serial Port Profile)  
: PBAP (Phone Book Access Profile)  
: OPP (Object Push Profile)  
: SYNC (Synchronization Profile)  
: A2DP (Advanced Audio Distribution Profile)  
: AVRCP (Audio/Video Remote Control Profile)  
|
70 KDC-BT60U/ KDC-6047U  
Audio section  
Maximum output power  
: 50 W x 4  
Output power (DIN 45324, +B=14.4V)  
: 30 W x 4  
Speaker Impedance  
: 4 – 8 Ω  
Tone action  
BAND1 (60 Hz): 9 dB  
BAND2 (250 Hz): 9 dB  
BAND3 (1 kHz): 9 dB  
BAND4 (4 kHz): 9 dB  
BAND5 (16 kHz): 9 dB  
Preout level / Load (CD)  
: 4000 mV/10 kΩ  
Preout impedance  
: ≤ 600 Ω  
Auxiliary input  
Frequency response ( 1 dB)  
: 20 Hz – 20 kHz  
Input Maximum Voltage  
: 1200 mV  
Input Impedance  
: 10 kΩ  
General  
Operating voltage  
KDC-BT60U (10.5 – 16V allowable) : 14.4 V  
KDC-6047U (11 – 16V allowable) : 14.4 V  
Maximum Current consumption  
: 10 A  
Installation Size (W x H x D)  
: 182 x 53 x 158 mm  
Weight  
: 1.30 kg  
Specifications subject to change without notice.  
English  
|
71  
Svenska  
Declaration of Conformity with regard to  
the EMC Directive 2004/108/EC  
Härmed intygar Kenwood att denna KDC-BT60U stär l överensstämelse med de  
väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av  
direktiv 1999/5/EG.  
For KDC-BT60U:  
Declaration of Conformity with regard to  
the R&TTE Directive 1999/5/EC  
Manufacturer:  
Kenwood Corporation  
2967-3 Ishikawa-machi, Hachioji-shi, Tokyo, 192-8525 Japan  
Suomi  
Kenwood vakuuttaa täten että KDC-BT60U tyyppinen laite on direktiivin  
1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen  
mukainen.  
Slovensko  
S tem Kenwood izjavlja, da je ta KDC-BT60U v skladu z osnovnimi zahtevami in  
ostalimi ustreznimi predpisi Direktive 1999/5/EC.  
Slovensky  
EU Representative's:  
Kenwood Electronics Europe BV  
Amsterdamseweg 37, 1422 AC UITHOORN, The Netherlands  
Spoločnosť Kenwood týmto vyhlasuje, že KDC-BT60U spĺňa zákldné požiadavky  
a ďalšie prislušné ustanovenia Direktĺvy 1999/5/EC.  
Dansk  
Undertegnede Kenwood erklærer harved, at følgende udstyr KDC-BT60U  
overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.  
Ελληνικά  
ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Kenwood ΔΗΛΩΝΕΙ ΟΤΙ KDC-BT60U ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ  
ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ  
1999/5/EK.  
English  
Hereby, Kenwood declares that this unit KDC-BT60U is in compliance with the  
essential requirements and other relevant provisions of Directive 1999/5/EC.  
Français  
Par la présente Kenwood déclare que l’appareil KDC-BT60U est conforme aux  
exigences essentielles et aux autres dispositions pertinentes de la directive  
1999/5/CE.  
Par la présente, Kenwood déclare que ce KDC-BT60U est conforme aux exigences  
essentielles et aux autres dispositions de la directive 1999/5/CE qui lui sont  
applicables.  
Eesti  
Sellega kinnitab Kenwood, et see KDC-BT60U vastab direktiivi 1999/5/EC  
põhilistele nõudmistele ja muudele asjakohastele määrustele.  
Latviešu  
Ar šo, Kenwood, apstiprina, ka KDC-BT60U atbilst Direktīvas 1999/5/EK  
galvenajām prasībām un citiem tās nosacījumiem.  
Lietuviškai  
Šiuo, Kenwood, pareiškia, kad šis KDC-BT60U atitinka pagrindinius Direktyvos  
1999/5/EB reikalavimus ir kitas svarbias nuostatas.  
Malti  
Hawnhekk, Kenwood, jiddikjara li dan KDC-BT60U jikkonforma mal-ħtiġijiet  
essenzjali u ma provvedimenti oħrajn relevanti li hemm fid-Dirrettiva 1999/5/  
EC.  
Deutsch  
Hiermit erklärt Kenwood, dass sich dieser KDC-BT60U in Übereinstimmung mit  
den grundlegenden Anforderungen und den anderen relevanten Vorschriften der  
Richtlinie 1999/5/EG befindet. (BMWi)  
Hiermit erklärt Kenwood die Übereinstimmung des Gerätes KDC-BT60U mit den  
grundlegenden Anforderungen und den anderen relevanten Festlegungen der  
Richitlinie 1999/5/EG. (Wien)  
Nederlands  
Українська  
Hierbij verklaart Kenwood dat het toestel KDC-BT60U in overeenstemming is  
met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/  
EG.  
Компанія Kenwood заявляє, що цей виріб KDC-BT60U відповідає ключовим  
вимогам та іншим пов’язаним положенням Директиви 1999/5/EC.  
Turkish  
Bij deze verklaat Kenwood dat deze KDC-BT60U voldoet aan de essentiële eisen  
en aan de overige relevante bepalingen van Richtlijn 1999/5/EC.  
Italiano  
Con la presente Kenwood dichiara che questo KDC-BT60U è conforme ai requisiti  
essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.  
Español  
Kenwood, işbu belge ile KDC-BT60U numaralı bu ünitenin 1999/5/EC  
Direktifi’nin özel gereksinimlerine ve ilgili diğer hükümlerine uygun olduğunu  
beyan eder.  
Por medio de la presente Kenwood declara que el KDC-BT60U cumple con los  
requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de  
la Directiva 1999/5/CE.  
Português  
For Turkey  
Kenwood declara que este KDC-BT60U está conforme com os requisitos  
essenciais e outras disposições da Directiva 1999/5/CE.  
Polska  
Bu ürün 26891sayılı Resmi Gazete’de yayımlanan  
Elektrikli ve Elektronik Eşyalarda Bazı Zararlı Maddelerin  
Kullanımının Sınırlandırılmasına Dair Yönetmeliğe  
uygun olarak üretilmiştir.  
Kenwood niniejszym oświadcza, że KDC-BT60U spełnia zasadnicze wymogi oraz  
inne istotne postanowienia dyrektywy 1999/5/EC.  
Český  
Kenwood timto prohlasuje, ze KDC-BT60U je ve shode se zakladnimi pozadavky  
a s dalsimi prislusnymi ustanoveni Narizeni vlady c. 426/2000 Sb.  
Magyar  
Alulírott, Kenwood, kijelenti, hogy a jelen KDC-BT60U megfelel az 1999/5/  
EC irányelvben meghatározott alapvető követelményeknek és egyéb vonatkozó  
előírásoknak.  
This product complies with Directive, Number 26891  
regarding “REGULATION ON THE RESTRICTION OF  
THE USE OF CERTAIN HAZARDOUS SUBSTANCES IN  
LECTRICAL AND ELECTRONIC EQUIPMENT.  
This symbol mark indicates that  
Kenwood manufactured this product  
so as to decrease harmful influence on  
the environment.  

Rockford Fosgate Car Speaker FRC3205 User Manual
Radio Shack 2901 User Manual
PYLE Audio View Series PLVS7HM User Manual
Philips SA2441BT User Manual
Peavey Electronics Car Speaker SP5BX User Manual
Panasonic Blu ray Player DMPBDT320EB User Manual
Panasonic AG HCK10 User Manual
Olympus Tracker 10 30 x 25 ZOOM PC I User Manual
Legacy Car Audio LA1838 User Manual
Konica Minolta Chroma Meter CS 200 User Manual