KDC-BT51U
KDC-5751SD
KDC-5051U
CD-RECEIVER
INSTRUCTION MANUAL
Before reading this manual, click the button below to check the latest edition and the
modified pages.
Check the latest edition
© 2010 Kenwood Corporation All Rights Reserved.
IM327_Ref_E_en_01
English
|
3
Before use
Before using this unit for the first time
This unit is initially set on the Demonstration mode.
When using this unit for the first time, cancel the
Demonstration mode. Refer to <Exit Demonstration
Mode> (page 4) of Quick start guide.
About discs used with this unit
• This unit can only play the CDs with
• The following discs cannot be used:
- Discs that are not round
- Discs with coloring on the recording surface or
discs that are dirty
- Recordable/Rewritable disc that has not been
finalized (For the finalization process, refer to
your disc writing software, and your disc recorder
instruction manual.)
- 8 cm (3 inch) disc (Attempt to insert using an
adapter can cause malfunction.)
.
2WARNING
To prevent injury or fire, take the following
precautions:
• Stop the car before operating the unit.
• To prevent a short circuit, never put or leave any
metallic objects (such as coins or metal tools) inside
the unit.
Handling discs
¤
CAUTION
• Do not touch the recording surface of the disc.
• Adjust the volume so that you can hear sounds
outside the car. Driving with the volume too high
may cause an accident.
• Wipe off the dirt on the panel with a dry silicon or
soft cloth.
• Do not stick tape etc. on the disc, or use a disc with
tape stuck on it.
• Do not use any accessories for the disc.
• Do not use any solvents to clean discs. Use a dry
silicon or soft cloth.
• Clean from the center of the disc and move
outward.
Failure to observe this precaution may result in
damage to the monitor or unit.”
• When removing discs from this unit, pull them out
horizontally.
• Remove the rims from the center hole and disc
edge before inserting a disc.
Cleaning the connector
Wipe off dirt on the connector of the unit and panel.
Use a cotton swab or cloth
Condensation
When the car is air-conditioned, moisture may collect
on the laser lens. This may cause disc read errors. In
this case, remove the disc and wait for the moisture
to evaporate.
How to reset your unit
If the unit fails to operate properly, press the Reset
button. The unit returns to factory settings when the
Reset button is pressed.
Reset button
Notes
• If you experience problems during installation,
consult your Kenwood dealer.
• When you purchase optional accessories, check with
your Kenwood dealer to make sure that they work
with your model and in your area.
• Characters that conform to ISO 8859-1 can be
displayed.
• Characters that conform to ISO 8859-5 or ISO 8859-
1 can be displayed. Refer to “Russian” of <Initial
setting> (page 31).
• The Radio data system feature won’t work where
the service is not supported by any broadcasting
station.
• The illustrations of the display and the panel
appearing in this manual are examples used to
explain more clearly how the controls are used.
Therefore, what appears on the display in the
illustrations may differ from what appears on the
display on the actual equipment, and some of the
illustrations on the display may be inapplicable.
|
4
KDC-BT51U/ KDC-5751SD/ KDC-5051U
English
|
5
Component names
Function setting
1 2 3 4
5
6
Function setting operation
Preferences of this unit can be set in the Function
setting mode. For detailed setting procedure and
items, refer to the explanation for each source
function.
1 Select the source
Press the [SRC] button.
w
q
p
9
8 7
Switch to the source to display the items to set.
1 [ ] button
2 Enter Function setting mode
Press the Control knob for at least 1 second.
2 Release button
3 [SRC] button
4 Control knob
5 [PRESET] button
6 [0] button
3 Select the Function item
Turn the Control knob to display the item to
set, and then press the Control knob.
Press the [
item.
] button to return to the previous
Example:
Play Mode
Settings
7 USB terminal
8 Auxiliary input
AUX Name Set
9
KDC-BT51U
Clock&Date
Summer Time
[
] [
] button
Initial Settings
Clock Adjust
KDC-5751SD
DISP&ILLUMI
Date Mode
[SD] button
KDC-5051U
In this Instruction manual, the procedure to select
“Clock Adjust” item in the Function setting layer as
above is described as the following example:
“Settings” > “Clock&Date” > “Clock Adjust”.
[iPod] button
p [LOG] button
q [DISP] button
4 Determine the setting value
w [
] button
Turn the Control knob to display the value to
set, and then press the Control knob.
The previous item is displayed.
5 Exit Function setting mode
Press the [
] button for at least 1 second.
|
6
KDC-BT51U/ KDC-5751SD/ KDC-5051U
Audio adjustments
Audio control
⁄
• You can set Bass, Middle, and Treble for each source.
About Supreme
You can adjust following Audio Control items;
Display
Audio item
Subwoofer level
Bass Boost
Preset Equalizer
curve
Range
–15 — +15 (dB)
Level1/Level2/OFF
“Rock”/“Pops”/“Easy”/
“Top40”/“Jazz”/ ”Game”/
“Natural”/“User”‡
Technology to extrapolate and supplement with proprietary
algorithm, the high-frequency range that is cut off when
encoding at low bit rate (less than 128Kbps, Sampling
frequency is 44.1kHz).
Supplementing is optimized by compression format (AAC,
MP3 or WMA) and processed according to bit rate.
The effect is negligible with music that is encoded at high
bit rate, variable bit rate or has minimal high frequency
range.
• About Dual Zone System
Main source and sub source (Auxiliary input) output Front
channel and Rear channel separately.
- When “2Zone” is set to “ON”, the main source sound and
AUX input sound are output to the front speakers and rear
speakers separately.
- Set up the channel of sub source by “2Zone”.
- Select Main source by [SRC] button.
- Adjust the volume of Front channel by Control knob.
- Adjust the volume of Rear channel by “2Zone Rear
Volume”.
- The Audio Control has no effect on sub source.
- When Bluetooth audio source is selected, set “2Zone F/R
Select” to “Rear”. “2Zone” cannot be turned “ON” when this
is set to “Front”. While “2Zone” is turned “ON”, “2Zone F/R
Select” function is disabled.
“SubWoofer Level”
“Bass Boost”
“System Q”
“Bass Adjust”
“Bass Center FRQ” Bass Center
40/50/60/70/80/100/
120/150 (Hz)
–8 — +8 (dB)
1.00/1.25/1.50/2.00
OFF/ON
Frequency
Bass level
“Bass Level”
“Bass Q Factor” Bass Q Factor
“Bass EXT”
Bass Extend
“Middle Adjust”
“Middle Center
FRQ”
“Middle Level”
“Middle Q Factor” Middle Q Factor
“Treble Adjust”
“Treble Center FRQ” Treble Center
Frequency
“Treble Level”
“Balance”
“Fader”
“2Zone Rear Volume” Rear volume during 0 — 35
Dual zone
“SubWoofer”
Middle Center
Frequency
Middle level
0.5/1.0/1.5/2.0 (kHz)
–8 — +8 (dB)
1.0/2.0
10.0/12.5/15.0/17.5 kHz
Treble level
Balance
Fader
–8 — +8 (dB)
Left 15 — Right 15
Rear 15 — Front 15
1 Select the source to adjust
Press the [SRC] button.
Subwoofer output OFF/ON
“Detailed Settings”
“HPF Front”
2 Enter Audio control mode
Press the Control knob.
Front High Pass
Filter
Rear High Pass Filter Through/40/60/80/100/
120/150/180/220 (Hz)
Through/40/60/80/100/
120/150/180/220 (Hz)
“HPF Rear”
3 Select the Audio item to adjust
Turn the Control knob to select the audio item
for adjustment and then press the Control
knob.
“LPF SubWoofer” Low Pass Filter
50/60/80/100/120/
Through (Hz)
“SubWoofer Phase” Subwoofer Phase Reverse (180°)/
Normal (0°)
“2Zone”
“2Zone F/R Select” Dual Zone output Rear/Front
channel
“Supreme”
Press the [
item.
] button to return to the previous
Dual Zone System ON/OFF
4 Adjust the Audio item
Turn the Control knob to display the value to
set, and then press the Control knob.
The previous item is displayed.
Supreme setting ON/OFF
“Audio Preset”
Audio Preset
Recall/Memory
memoy†
“Volume Offset
ADJ”
Volume offset
–8 — 0 (dB)
(AUX: -8 — +8)
5 Exit Audio control mode
Press the [
] button for at least 1 second.
†Refer to <Audio preset Memory> (page 8), <Audio preset
recall> (page 8).
‡“User”: The customized Bass, Middle, and Treble levels are
effective.
English
|
7
Audio adjustments
Audio preset Memory
Audio preset recall
Registering the value setup by Audio Control.
Recalling the sound setup registered by <Audio
preset Memory> (page 8).
1 Setup Audio control
Setup the <Audio control> (page 7).
1 Select the source
Press the [SRC] button.
2 Enter Audio control mode
Press the Control knob.
2 Enter Audio control mode
Press the Control knob.
3 Select Audio preset memory mode
The item can be selected and determined as
follows.
“Detailed Settings” > “Audio Preset”
To select the item, turn the Control knob. To
determine the item, press the Control knob.
3 Select Audio preset memory mode
The item can be selected and determined as
follows.
“Detailed Settings” > “Audio Preset”
To select the item, turn the Control knob. To
determine the item, press the Control knob.
4 Select the Audio preset memory
Turn the Control knob to select “Memory”, and
then press the Control knob.
4 Select the Audio preset recall
Turn the Control knob to select “Recall”, and
then press the Control knob.
5 Turn the Control knob to select “YES”, and
then press the Control knob.
“Memory Completed” is displayed.
5 Turn the Control knob to select “YES”, and
then press the Control knob.
“Recall Completed” is displayed.
6 Exit Audio Control mode
Press the [
] button for at least 1 second.
6 Exit Audio Control mode
Press the [
] button for at least 1 second.
⁄
• Register 1 pair of Audio Preset Memory. You cannot register
by the source.
• When you press the Reset, all the sources will be the setting
value which is registered.
• The following items can be registered.
“Bass Center FRQ”, “Bass Level”, “Bass Q Factor”, “Bass EXT”,
“Middle Center FRQ”, “Middle Level”, “Middle Q Factor”,
“Treble Center FRQ”, “Treble Level”, “SubWoofer Level”, “HPF
Front”, “HPF Rear”, “LPF SubWoofer”, “SubWoofer Phase”
|
8
KDC-BT51U/ KDC-5751SD/ KDC-5051U
iPod control operation
For basic operation to playback iPod contents, refer
to the Quick Start Guide.
Alphabet search
You can select an alphabetic character from the
list in the browse item (artist, album, etc.) currently
selected.
Music search
1 Enter Music search mode
Press the [ ] button twice.
“MUSICSEARCH” is displayed.
Searching for the song you want to play.
1 Enter Music search mode
Press the [ ] button.
“MUSICSEARCH” is displayed.
2 Select Alphabet search mode
Turn the Control knob to select “Alphabet
Search”, and then press the Control knob.
2 Search for music
3 Search for character
Operation type
Operation
Operation type
Operation
Movement between items Turn the Control knob.
Select the characters
Determine the characters.
Turn the Control knob.
Press the Control knob.
Move to the Alphabet
search mode
Press the [ ] button for at least 1
second. Refer to <Alphabet search>
(page 9).
Return to the Music search mode.
Selection of item
Press the Control knob.
Cancelling the Alphabet search mode
Return to previous item
Return to Top menu
Press the [ ] button.
Push the Control knob towards left for at
least 1 second.
Press the [
] button for at least 1 second.
⁄
• The time of Alphabet search may become long depending
on the number of items (songs) in iPod.
Cancelling the Music search mode
Press the [ ] button for at least 1 second.
• To search for a character other than A to Z and 1, enter “*”.
• If the first character string begins with an article “a”, “an”,
or “the” in the alphabet search mode, it is searched for in
defiance of the article.
⁄
• If no characters included in a song name can be displayed,
the browse item name and digits are displayed.
Items
Playlists
Artists
Albums
Songs
Display
“PLIST***” Podcasts
“ART***”
“ALB***”
“PRGM***”
Items
Display
“PDCT***”
“GEN***”
“COM***”
Genres
Composers
English
|
9
iPod control operation
Related search
Direct search
Browsing for music of the same artist or genre as
the one being played.
Searching for music by selecting a browse item and
an alphabetic character(s).
1 Enter Search select mode
Press the [ ] button for at least 1 second.
1 Enter Search select mode
Press the [ ] button for at least 1 second.
2 Select Related search mode
Turn the Control knob to select “Related
Search”, and then press the Control knob.
2 Select Direct search mode
Turn the Control knob to select “Direct Search”,
and then press the Control knob.
3 Select desired browsing item
Turn the Control knob to select browse item,
and then press the Control knob.
3 Select browse item
Turn the Control knob to select browse item,
and then press the Control knob.
Display
Browses music
Display
Browses item
“Search Artist”
“Search Album”
Displays the album of the same artist.
Displays music in the album in which the one
being played is included.
“PLAYLISTS”
Playlists
“ARTISTS”
Artists
“Search Genre”
Displays the artist of the same genre.
“ALBUMS”
“SONGS”
Albums
Songs
“Search Composer” Displays the album including music created by the
same composer.
“PODCASTS”
“GENRES”
Podcasts
Genres
4 Search for music
Operation type
Operation
Movement between items Turn the Control knob.
“COMPOSERS”
Composers
Selection of item
Return to previous item
Press the Control knob.
Press the [ ] button.
4 Select the character to be searched for
Turn the Control knob to select character, and
then press the Control knob.
Cancelling the Related search mode
Press the [ ] button for at least 1 second.
You can select up to three characters.
⁄
5 Search for music
• Related search cannot be performed while playing a
Podcast.
Turn the Control knob to select “DONE”, and
then press the Control knob.
A search result list is displayed.
• When the music being played has no information on
browsing items or no music was found, “Not Found” is
displayed.
6 Select the music
Turn the Control knob to select music, and then
press the Control knob.
Cancelling the Direct search mode
Press the [
] button for at least 1 second.
|
10 KDC-BT51U/ KDC-5751SD/ KDC-5051U
Skip search
Skip search ratio setting
The number of songs to be skipped is determined
by the ratio of the total number of songs in the list
which is selected.
Sets the ratio of skip performed with <Skip search>
(page 11).
1 Select iPod source
Press the [SRC] button.
Select the “iPod” display.
1 Enter Music search mode
Press the [ ] button.
“MUSICSEARCH” is displayed.
2 Enter Function setting mode
2 Enter Search select mode
Press the [ ] button.
Press the Control knob for at least 1 second.
3 Select the Skip search
The item can be selected and determined as
follows.
3 Select Skip search mode
Turn the Control knob to select “Skip Search”,
and then press the Control knob.
“Settings” > “Skip Search”
To select the item, turn the Control knob. To
determine the item, press the Control knob.
4 Search for music
Operation type
Operation
4 Set the Skip search ratio
Movement between items Turn the Control knob.
Skip Search
Push the Control knob towards up or down.
Turn the Control knob to select ratio (“0.5%”,
“1%”, “5%”, or “10%”), and then press the
Control knob.
Selection of item
Sets the ratio of skip
performed
Press the Control knob.
Push the Control knob towards right or left.
5 Exit Function setting mode
Cancelling the Music search mode
Press the [ ] button for at least 1 second.
Press the [
] button for at least 1 second.
⁄
• The ratio of the Skip Search is set to 0.5% as default. Refer to
<Skip search ratio setting> (page 11).
• Keep pushing Control knob for 3 seconds or longer skips
songs at 10% regardless of the setting.
English
|
11
iPod control operation
Play mode
Registering a song in the playlist
You can select a Play Mode, such as Random play
and Repeat play.
You can register your favorite songs to make a
playlist. You can register up to ten songs in the
playlist.
1 Select iPod source
Press the [SRC] button.
Select the “iPod” display.
1 Play the song you want to register
Push the Control knob towards up, down, right,
and left.
2 Enter Function setting mode
Press the Control knob for at least 1 second.
2 Enter Search select mode
Press the [ ] button for at least 1 second.
3 Select the Play mode
Turn the Control knob to select “Play Mode”,
and then press the Control knob.
3 Register the song
Turn the Control knob to select “Register My
Playlist”, and then press the Control knob.
“## (registration number) Stored” is displayed. You
can register up to ten songs.
4 Select the desired Play function
Turn the Control knob to select Play function,
and then press the Control knob.
Display
“Play Mode”
Overview
In Music search mode
“iPod by Hand” When set to“ON”, allows you to operate iPod
with the control on the iPod.
1 Enter Music search mode
Press the [ ] button.
“MUSICSEARCH” is displayed.
“ON” / “OFF”
“Folder Random” When set to“ON”, plays the music in the folder
randomly. (Music only)
2 Play the song you want to register
Refer to <Music search> (page 9).
“ON” / “OFF”
“All Random”
“File Repeat”
When set to“ON”, plays all songs in iPod
randomly. (Music only)
“ON” / “OFF”
When set to“ON”, plays the music repeatedly.
“ON” / “OFF”
3 Enter Register playlist mode
Press the [ ] button.
4 Register the song
Turn the Control knob to select “Register My
Playlist”, and then press the Control knob.
“## (registration number) Stored” is displayed. You
can register up to ten songs.
(
: Factory setting)
5 Set the Play function
Press the Control knob.
The previous item is displayed.
⁄
6 Exit Function setting mode
• When creating a playlist, you can register the songs stored
in one iPod. If you attempt to register a song by connecting
an unregistered iPod, “My Playlist Delete” is displayed.
Selecting “YES” deletes the playlist.
Press the [
] button for at least 1 second.
• If you attempt to register the eleventh song, “Memory Full”
is displayed and you cannot register the song. To register it,
delete an unnecessary song.
• Do not register Podcasts. Songs may be registered or played
improperly. For example, unintended songs are registered.
|
12 KDC-BT51U/ KDC-5751SD/ KDC-5051U
Playing the playlist
Deleting a song from the playlist
1 Enter Search select mode
Press the [ ] button for at least 1 second.
1 Enter Search select mode
Press the [ ] button for at least 1 second.
2 Select Recall playlist mode
Turn the Control knob to select “Recall My
Playlist”, and then press the Control knob.
2 Select Delete playlist mode
Turn the Control knob to select “Delete My
Playlist”, and then press the Control knob.
3 Play a song in the playlist
3 Select how to delete song(s)
Turn the Control knob to select the song you
want to play, and then press the Control knob.
Turn the Control knob to select “Delete One” or
“Delete All”, and then press the Control knob.
Selecting “Delete All” deletes all songs.
Selecting “Delete All” moves to step 5 and all songs
are deleted.
⁄
• To stop playing the song in the playlist, turn the power off.
• If a song does not end with 1 second or longer silence, its
last portion may not be played.
4 Select the song to delete
Turn the Control knob to select the song, and
then press the Control knob.
• Songs cannot be played at random during playback of the
songs in playlist.
5 Turn the Control knob to select “YES”, and then
press the Control knob.
“Completed” is displayed.
In Function setting mode
1 Select iPod source
Press the [SRC] button.
Select the “iPod” display.
2 Enter Function setting mode
Press the Control knob for at least 1 second.
3 Select the Playlist delete mode
The item can be selected and determined as
follows.
“Settings” > “My Playlist Delete” > “Delete One”
or “Delete All”
To select the item, turn the Control knob. To
determine the item, press the Control knob.
Selecting “Delete All” deletes all songs.
Selecting “Delete All” moves to step 5 and all songs
are deleted.
4 Select the song to delete
Turn the Control knob to select the song, and
then press the Control knob.
5 Turn the Control knob to select “YES”, and then
press the Control knob.
“Completed” is displayed.
6 Exit Function setting mode
Press the [
] button for at least 1 second.
English
|
13
Music disc/Audio file (CD, USB, or SD) Operation
For basic operation to playback Music disc/Audio
file contents, refer to the Quick Start Guide.
Music Editor media
Skip search
The number of songs to be skipped is determined
by the ratio of the total number of songs in the list
which is selected.
Music search
1 Enter Music search mode
Press the [ ] button.
Selecting the music you want to listen to from the
device or media being played now.
“MUSICSEARCH” is displayed.
1 Enter Music search mode
Press the [ ] button.
“MUSICSEARCH” is displayed.
2 Enter Search select mode
Press the [ ] button.
3 Select Skip search mode
Turn the Control knob to select “Skip Search”,
and then press the Control knob.
2 Search for music
Audio file
Operation type
Movement between
folders/files
Selection of folder/flie Press the Control knob.
Return to previous folder Press the [ ] button.
Operation
Turn the Control knob.
4 Search for music
Operation type
Operation
Movement between items Turn the Control knob.
Skip Search
Selection of item
Sets the ratio of skip
performed
Push the Control knob towards up or down.
Press the Control knob.
Push the Control knob towards right or left.
Return to root folder
Push the Control knob towards left for at
least 1 second.
Cancel the Music Search Press the [ ] button for at least 1 second.
mode
Cancelling the Music search mode
Press the [ ] button for at least 1 second.
¡ indicator: Audio file
] indicator: Folder
⁄
• The ratio of the Skip Search is set to 0.5% as default. Refer to
<Skip search ratio setting> (page 11).
• Keep pushing Control knob for 3 seconds or longer skips
songs at 10% regardless of the setting.
CD source
Operation type
Movement between track Turn the Control knob.
Operation
Selection of track
Press the Control knob.
Return to first track
Push the Control knob towards left for at
least 1 second.
Cancel the Music Search Press the [ ] button.
mode
|
14 KDC-BT51U/ KDC-5751SD/ KDC-5051U
Function of disc changers with KDC-5751SD/
KDC-5051U
Play mode
You can select a Play Mode, such as Random play
and Repeat play.
Basic operation of Disc changer
(Optional)
1 Select CD/ USB/ SD source
Press the [SRC] button.
Select the “CD”, “USB”, or “SD” display.
Selecting CD changer source
Press the [SRC] button.
Select the “CD CH” display.
2 Enter Function setting mode
Press the Control knob for at least 1 second.
Music search
Push the Control knob towards right or left.
3 Select the Play function mode
Turn the Control knob to select “Play Mode”,
and then press the Control knob.
Disc search
Push the Control knob towards up or down.
4 Select the desired Play function
Turn the Control knob to select Play function,
and then press the Control knob.
Display
Overview
“Play Mode”
“Track Scan”(CD)/ When set to“ON”, plays the intro of the music
“File Scan”(Audio in the disc/folder successively.
file)
“ON” / “OFF”
“Disc Random”(CD)/ When set to“ON”, plays the music in the folder
“Folder Random” randomly.
(Audio file)
“ON” / “OFF”
“All Random”
When set to“ON”, plays all songs in CD/USB
randomly. (Audio file only)
“ON” / “OFF”
“Track Repeat”(CD)/ When set to“ON”, plays the music repeatedly.
“File Repeat”(Audio “ON” / “OFF”
file)
“Disc Repeat”(CD When set to“ON”, plays the music in the disc/
changer)/“Folder folder repeatedly.
Repeat”(Audio file) “ON” / “OFF”
“MGZN Random” When set to“ON”, plays the music in the disc
changer randomly. (Disc changer only)
“ON” / “OFF”
(
: Factory setting)
5 Set the Play function
Press the Control knob.
The previous item is displayed.
6 Exit Function setting mode
Press the [
] button for at least 1 second.
⁄
KDC-5751SD
• Press the SD button during SD source, move to the Play
function mode.
English
|
15
Tuner Operation
For basic operation to listen to the radio, refer to the
Quick Start Guide.
Seek mode setting
Selects the tuning mode of the radio.
1 Select Tuner source
Press the [SRC] button.
Select the “TUNER” display.
Auto memory
Memorizes 18 (FM)/ 6 (AM) stations with good
reception automatically.
2 Enter Function setting mode
Press the Control knob for at least 1 second.
1 Select Tuner source
Press the [SRC] button.
Select the “TUNER” display.
3 Select the Seek mode
The item can be selected and determined as
follows.
“Settings” > “Seek Mode”
To select the item, turn the Control knob. To
determine the item, press the Control knob.
2 Enter Function setting mode
Press the Control knob for at least 1 second.
3 Select the Auto memory mode
The item can be selected and determined as
follows.
4 Set to the desired Seek mode
Tuning mode
Display Operation
Auto seek
“Auto1” Automatic search for a station.
“Settings” > “Auto Memory”
Preset station seek “Auto2” Search in order of the stations in the
Preset memory.
To select the item, turn the Control knob. To
determine the item, press the Control knob.
Manual
“Manual” Normal manual tuning control.
4 Start Auto memory mode
Turn the Control knob to select “YES”, and then
press the Control knob.
Turn the Control knob to select Seek mode, and
then press the Control knob.
5 Exit Function setting mode
When 18 (FM)/ 6 (AM) stations that can be received
are put in the memory, auto memory entry closes.
Press the [
] button for at least 1 second.
|
16 KDC-BT51U/ KDC-5751SD/ KDC-5051U
6 Exit Function setting mode
Press the [ ] button for at least 1 second.
Tuner setting
Sets the tuner items.
1 Select Tuner source
Press the [SRC] button.
Select the “TUNER” display.
2 Enter Function setting mode
Press the Control knob for at least 1 second.
3 Select the Setting mode
Turn the Control knob to select “Settings”, and
then press the Control knob.
4 Select the desired Tuner setting item
Turn the Control knob to select Tuner setting
item, and then press the Control knob.
Display
Overview
“Settings”
“Local Seek”
Only stations whose reception is good are
searched in auto seek tuning.
“ON” / “OFF”
“MONO”
You can reduce the noise when stereo
broadcasts are received as monaural.
“ON” / “OFF”
“News Interrupt” Automatically receives news bulletin when
it starts. Set the time during which interrupt
is to be disabled after start of another news
bulletin.
Changing“00MIN”to“90MIN”turns this
function ON.
If news bulletin starts when this function is
ON, “NEWS”is displayed and news is received.
If“20MIN”is has been set, reception of another
news bulletin will not start for 20 minutes.
The news bulletin volume is the same level
that was set for Traffic Information.
“OFF” / “00MIN” – “90MIN”
“AF”
When the reception is poor, automatically
alternate to another frequency broadcasting
the same program in the same Radio data
system network with better reception.
“ON” / “OFF”
“Regional”
Sets whether to switch to the station only in
the specific region using the“AF SET”control.
“ON” / “OFF”
“Auto TP Seek”
When traffic information station reception is
poor, automatically searches for a station that
can be received better.
“ON” / “OFF”
(
: Factory setting)
5 Set the Tuner setting item
Turn the Control knob to select desired value,
and then press the Control knob.
The previous item is displayed.
English
|
17
Tuner Operation
PTY (Program Type)
Program Type preset
Selecting the Program Type below and searching
for a station;
Putting the Program Type in the Preset button
memory and quick recall.
Program Type Display
Program Type Display
Serious Classical “Classics”
Presetting the Program Type
Speech
Music
News
“Speech”
“Music”
“News”
1 Select the Program Type to preset
Refer to <PTY (Program Type)> (page 18).
Other Music
Weather
Finance
“Other M”
“Weather”
“Finance”
Current Affairs
Information
Sport
“Affairs”
“Info”
“Sport”
2 Enter Program Type preset mode
Press the [PRESET] button.
Children’s programs “Children”
Social Affairs
Religion
Phone In
“Social”
3 Select a number and store it in the memory
Turn the Control knob to select memory
number (“1” – “6”), and then press the Control
knob for at least 2 seconds.
Education
Drama
Culture
Science
Varied
Pop Music
Rock Music
Easy Listening
Music
“Educate”
“Drama”
“Culture”
“Science”
“Varied”
“Pop M”
“Rock M”
“Easy M”
“Religion”
“Phone In”
“Travel”
Travel
Leisure
“Leisure”
“Jazz”
“Country”
“Nation M”
“Oldies”
Jazz Music
Country Music
National Music
Oldies Music
Folk Music
Documentary
Cancelling the Preset Memory mode
Press the [
] button.
Recalling the preset Program Type
“Folk M”
“Document”
Light Classical
“Light M”
1 Enter PTY mode
Press the [ ] button twice.
• Speech and Music include the Program type shown
below.
Music: Black character item.
Speech: White character item.
2 Enter Preset memory mode
Press the [PRESET] button.
3 Select the number you want to recall from the
memory
Turn the Control knob to select recall number
(“1” – “6”), and then press the Control knob.
1 Enter PTY mode
Press the [ ] button twice.
2 Select the Program Type
Turn the Control knob.
3 Search for the selected Program Type station
Push the Control knob towards right or left.
4 Exit PTY mode
Press the [
] button.
⁄
• This function cannot be used during a traffic bulletin or AM
reception.
• When the selected Program Type is not found, “No PTY” is
displayed. Select another Program Type.
|
18 KDC-BT51U/ KDC-5751SD/ KDC-5051U
Changing Language for PTY Function
Selecting the Program Type display language as
follows;
Language
English
French
Display
“English”
“French”
“German”
German
1 Enter PTY mode
Press the [ ] button twice.
2 Enter Changing Language mode
Press the Control knob.
3 Select the language
Turn the Control knob to select language, and
then press the Control knob.
English
|
19
Log memory
Log memory recall
Log memory item lock
This unit automatically memorizes the previously
used functions and Function setting items, which
can easily be recalled.
Locks Log memory items to avoid them being
deleted.
1 Display the Log memory list
Press the [LOG] button.
1 Display the Log memory list
Press the [LOG] button.
2 Lock the Log memory item
2 Recall the desired function
Turn the Control knob to select function, and
then press the Control knob.
Turn the Control knob to select item, and then
press the Control knob for at least 1 second.
Locked items are indicated with “ ”.
Category display
“FM”
“AM”
“iPod”
“USB”
Function category
FM broadcast
AM broadcast
iPod music
3 Exit Log memory
Press the [
] button.
USB music
“SD”
SD card
“CD”
CD music
“PLAY”
“INIT”
“SET”
Play mode item
Initial setting item
Setting item
“DISP”
“AUD”
“BT”
Display setting item
Audio control setting
Calling number
Cancelling the Log memory recall
Press the [ ] button.
⁄
• Maximum of 15 recently used functions are logged. When
this limit is reached, they are deleted from the oldest.
• Logged functions can be deleted. Refer to <Deleting a Log
memory item> (page 21).
• Functions to be logged can be set by categories. Refer to
<Log memory category setting> (page 21).
• Logged functions can be locked to avoid them being
deleted. Refer to <Log memory item lock> (page 20).
• Stations are logged after 2 minutes of reception.
This timing can be changed. Refer to <Tuner log memory
time setting> (page 22).
|
20 KDC-BT51U/ KDC-5751SD/ KDC-5051U
Deleting a Log memory item
Log memory category setting
Deletes Log memory items.
Sets the function category to be logged.
1 Enter Function setting mode
Press the Control knob for at least 1 second.
1 Enter Function setting mode
Press the Control knob for at least 1 second.
2 Select the Log delete mode
The item can be selected and determined as
follows.
2 Select the Log memory setting mode
The item can be selected and determined as
follows.
“Settings” > “Log” > “Log Delete”
To select the item, turn the Control knob. To
determine the item, press the Control knob.
“Settings” > “Log” > “Log Settings”
To select the item, turn the Control knob. To
determine the item, press the Control knob.
3 Select the Log memory item to delete
Turn the Control knob to select Log memory
item, and then press the Control knob.
Selecting “All” deletes all Log memory. (exclude a
locked items.)
3 Set the category to be logged
Category display
“Tuner Log”
“Data CD Log”
“iPod Log”
Setting category
Radio-related
CD-related
iPod-related
“USB Log”
“SD Log”
“Phone Log”
“Function Log”
USB-related
SD card-related (KDC-5751SD only)
Call-related
4 Turn the Control knob to select “YES”, and then
press the Control knob.
“Completed” is displayed.
Function setting-related
5 Exit Function setting mode
Turn the Control knob to select category, and
then press the Control knob.
Press the [
] button for at least 1 second.
4 Exit Function setting mode
Press the [
] button for at least 1 second.
English
|
21
Log memory
Tuner log memory time setting
You can set the timing to log the station by the
reception time.
1 Enter Function setting mode
Press the Control knob for at least 1 second.
2 Select the Tuner log time set mode
The item can be selected and determined as
follows.
“Settings” > “Log” > “Tuner Log Time Set”
To select the item, turn the Control knob. To
determine the item, press the Control knob.
3 Set the reception time for the timing to start
logging the station
Turn the Control knob to select time (“10SEC”,
“30SEC”, “1MIN”, “2MIN”, or “5MIN”), and then
press the Control knob.
4 Exit Function setting mode
Press the [
] button for at least 1 second.
|
22 KDC-BT51U/ KDC-5751SD/ KDC-5051U
English
|
23
Display settings
Selecting display type
Selecting text display
Shown below are examples of display types.
Changes displayed information on each of the
following sources:
Display type Display information
Type A
Type B
Type C
Type D
Type E
Displays 3 lines of text.
Displays 2 line of text.
Displays the clock.
Displays the spectrum analyzer.
Displays off.
In Tuner source
Information
Frequency & Program Service name (FM)
Song title† (FM)*
Artist name† (FM)*
Title & Artist name† (FM)**
Station name† (FM)
Radio text +† (FM)
Radio text† (FM)
Frequency (MW, LW)
Spectrum analyzer & Clock
Date
Display
“Frequency/PS”
“Song Title”
“Artist Name”
“Title/Artist”
“Station Name”
“Radio Text Plus”
“Radio Text”
“Frequency”
“Speana/Clock”
“Date”
1 Enter Function setting mode
Press the Control knob for at least 1 second.
2 Select the Display type select mode
The item can be selected and determined as
follows.
“Settings” > “DISP&ILLUMI” > “Display Select” >
“Type Select”
Blank
“Blank”
†Information of Radio text plus is displayed.
*Dispaly type A only
To select the item, turn the Control knob. To
determine the item, press the Control knob.
**Dispaly type B only
3 Select the Display type
Turn the Control knob to select Display type,
and then press the Control knob.
In CD & External disc source
Information
Disc title
Display
“Disc Title”
“Track Title”
“P-Time”
Track title
Play time
4 Exit Function setting mode
Press the [
] button for at least 1 second.
Spectrum analyzer & Clock
Date
“Speana/Clock”
“Date”
Blank
“Blank”
In Audio file/ iPod source
Information
Display
Song Title*
Album name*
Artist name*
Title & Artist name**
Album & Artist name
Folder name
“Song Title“
“Album Name”
“Artist Name”
“Title/Artist”
“Album/Artist”
“Folder Name”
“File Name”
“P-Time”
File name
Play time
Spectrum analyzer & Clock
Date
“Speana/Clock”
“Date”
Blank
“Blank”
*Dispaly type A only
**Dispaly type B only
In Standby/ Auxiliary input source
Information
Display
Source name
Spectrum analyzer & Clock (AUX only)
Clock (Standby only)
“Source Name”
“Speana/Clock”
“Clock”
Date
“Date”
Blank
“Blank”
|
24 KDC-BT51U/ KDC-5751SD/ KDC-5051U
In Bluetooth Audio “BT AUDIO EXT” (Optional
accessory KCA-BT200, KCA-BT300) source
Information display setting
Sets side and graphic parts of the display.
Information
Display
Source name
Spectrum analyzer & Clock
Date
“Source Name”
“Speana/Clock”
“Date”
1 Enter Function setting mode
Press the Control knob for at least 1 second.
2 Select the Display select mode
The item can be selected and determined as
follows.
Title & Artist name (KCA-BT300 only)
Album & Artist name (KCA-BT300 only)
Blank
“Title/Artist”
“Album/Artist”
“Blank”
“Settings” > “DISP&ILLUMI” > “Display Select”
To select the item, turn the Control knob. To
determine the item, press the Control knob.
1 Enter Function setting mode
Press the Control knob for at least 1 second.
3 Select the desired Information display setting
item
Turn the Control knob to select Display setting
item, and then press the Control knob.
2 Select Text display selection mode
The item can be selected and determined as
follows.
“Settings” > “DISP&ILLUMI” > “Display Select” >
“Text Select”
Display
Overview
To select the item, turn the Control knob. To
determine the item, press the Control knob.
“Display Select”
“Side Select”
Sets the side part display for Type A, B, and D.
1 / 2 / 3
3 Select the text display part
Push the Control knob towards up or down.
The selected text display part blinks.
“Graphic Select”
“Status”
Sets the Type C clock display and Type D
spectrum analyzer display.
1 / 2
Sets the status display (ON/OFF indicator for
each function) for Type A and B.
“ON” / “OFF”
4 Select the text
Turn the Control knob.
5 Exit Function setting mode
(
: Factory setting)
Press the [
] button for at least 1 second.
4 Set the Display setting item
⁄
Turn the Control knob to select desired value,
and then press the Control knob.
The previous item is displayed.
• If the selected display item does not have any information,
alternative information is displayed.
• Setting is available when the Display type is A or B which
allows text display. Refer to <Selecting display type> (page
24).
5 Exit Function setting mode
Press the [
] button for at least 1 second.
• Some items cannot be selected depending on the display
type and row.
• When selecting “Folder name” while playing with iPod,
names will be displayed depending on currently selected
browsing items.
• If the iPod Control by Hand Mode is set to on while playing
the iPod, “iPod by Hand Mode” is displayed.
• If all characters cannot be displayed while playing with iPod,
the file number in the list is displayed.
Information
Music title
Folder name
File name
Display
“TITLE***”
“FLD***”
“FILE***”
English
|
25
Display settings
Illumination color selection
Display & Illumination setting
Selecting the Illumination Color of the panel.
Sets the display and illumination.
1 Enter Function setting mode
Press the Control knob for at least 1 second.
1 Enter Function setting mode
Press the Control knob for at least 1 second.
2 Select Color select mode
The item can be selected and determined as
follows.
2 Select Display & Illumination setting mode
The item can be selected and determined as
follows.
“Settings” > “DISP&ILLUMI” > “Color Select”
To select the item, turn the Control knob. To
determine the item, press the Control knob.
“Settings” > “DISP&ILLUMI”
To select the item, turn the Control knob. To
determine the item, press the Control knob.
3 Select the part where you want to set the
Illumination Color
3 Select the desired Display & Illumination
setting item
Turn the Control knob to select Display &
Illumination setting item, and then press the
Control knob.
Display
“Color Select”
“ALL”
Part
All
“Display”
“Key”
Display
Button
Display
“DISP&ILLUMI”
Overview
“USB&AUX”
USB terminal and Auxiliary input
“Display Dimmer” Dims the display part in conjunction with the
light switch of the vehicle.
Turn the Control knob to select part, and then
press the Control knob.
“Auto”: Dims the display in conjunction with
the Light switch of the vehicle.
“Manual1”: Dims the display constantly.
“Manual2”: Dims the display darker than
Manual1.
“OFF”: Does not dim the display.
Sets the display contrast.
4 Select the Illumination Color
Turn the Control knob to select color, and then
press the Control knob.
Select the color from “Variable Scan”/ “Color1” —
“Color24”.
“Contrast”
“1” – ”10” – “30”
“DISP NEGA/POSI” Switches the panel display between positive
or negative.
Adjusting RGB values
You can create your original color during the
selection from “Color1” — “Color24.”
The color you created can be called when you
select “User”.
1. Press the Control knob for at least 1 second.
Enter the detail color adjustment mode.
2. Set the color.
“NEGA1”: Displays the text in the negative.
“NEGA2”: When the interior light is off, the
text is displayed in the negative;
when the interior light is on, the text
is displayed in the positive.
“POSI1”: Displays the text in the positive.
“POSI2”: When the interior light is off, the text
is displayed in the positive; when
the interior light is on, the text is
displayed in the negative.
Sets the method of scroll to view hidden text.
“Auto” : Scrolls.
“Once” : Scrolls once.
“OFF” : Does not scroll.
Operation type
To select the color to adjust. Push the Control knob towards right
(red, green, or blue)
To adjust color.
(Range: 0 – 9)
Operation
“Text Scroll”
or left.
Turn the Control knob.
3. Press the Control knob.
Exit the detail color adjustment mode.
“BT DVC Status”
You can display the connection status, signal
strength, and battery level.
: Battery level of cell-phone.
: Signal strength of cell-phone.
5 Exit Function setting mode
Press the [
] button for at least 1 second.
|
26 KDC-BT51U/ KDC-5751SD/ KDC-5051U
“ILLUMI Dimmer” Reduces the key Illumination brightness.
“Auto”: Dims the illumination in conjunction
with the Light switch of the vehicle.
“Manual1”: Dims the illumination constantly.
“Manual2”: Dims the illumination darker than
Manual1.
“OFF”: Does not dim the illumination.
“ILLUMI Effect”
Sets whether the key illumination color is
changed in conjunction with the key operation.
“ON” / “OFF”
“ILLUMI Music
SYNC”
Sets whether the key illumination color is
changed in conjunction with the sound
volume.
“ON” / “OFF”
(
: Factory setting)
4 Set the Display & Illumination setting items
Turn the Control knob to select desired value,
and then press the Control knob.
The previous item is displayed.
5 Exit Function setting mode
Press the [
] button for at least 1 second.
English
|
27
General operation
Adjusting the Clock
Adjusting the Date
1 Enter Function setting mode
Press the Control knob for at least 1 second.
1 Enter Function setting mode
Press the Control knob for at least 1 second.
2 Select the Clock Adjust mode
The item can be selected and determined as
follows.
2 Select the Date Adjust mode
The item can be selected and determined as
follows.
“Settings” > “Clock&Date” > “Clock Adjust”
To select the item, turn the Control knob. To
determine the item, press the Control knob.
“Settings” > “Clock&Date” > “Date Adjust”
To select the item, turn the Control knob. To
determine the item, press the Control knob.
3 Set hour
3 Set year
Turn the Control knob to adjust the hour, and
then press the Control knob.
Turn the Control knob to adjust the year, and
then press the Control knob.
4 Set minute
Turn the Control knob to adjust the minute, and
then press the Control knob.
4 Set month
Turn the Control knob to adjust the month, and
then press the Control knob.
5 Exit Function setting mode
5 Set day
Press the [
] button for at least 1 second.
Turn the Control knob to adjust the day, and
then press the Control knob.
⁄
• For adjustment during summer time, refer to “Summer Time”
6 Exit Function setting mode
Press the [
of <Clock & Date display type setting> (page 29).
] button for at least 1 second.
|
28 KDC-BT51U/ KDC-5751SD/ KDC-5051U
Dual clock display
Clock & Date display type setting
Sets time for two different cities.
Sets the display type of the clock and calendar.
1 Enter Function setting mode
Press the Control knob for at least 1 second.
1 Enter Function setting mode
Press the Control knob for at least 1 second.
2 Select the City Select mode
The item can be selected and determined as
follows.
2 Select the Clock & Date setting mode
The item can be selected and determined as
follows.
“Settings” > “Clock&Date” > “City Select”
To select the item, turn the Control knob. To
determine the item, press the Control knob.
“Settings” > “Clock&Date”
To select the item, turn the Control knob. To
determine the item, press the Control knob.
3 Select the clock display part
3 Select the desired Clock & Date setting item
Turn the Control knob to select Clock & Date
display setting item, and then press the Control
knob.
Push the Control knob towards up or down.
4 Set cities for Home/ Sub
Turn the Control knob.
Display
“Clock&Date”
Overview
5 Determine cities for Home/ Sub
Press the Control knob.
“Time Synchronized” Synchronizing the Radio data system station
time data and this unit’s clock.
6 Exit Function setting mode
“ON” / “OFF”
Advances the clock one hour when set to ON.
“ON” / “OFF”
Press the [
] button for at least 1 second.
“Summer Time”
⁄
• For adjustment of Home time, refer to <Adjusting the
Clock> (page 28).
“Sub Clock Adjust” Adjusts the time difference caused by summer
time.
• Time of Sub City is automatically derived from Home time.
When summer time systems are different between Home
and Sub cities, adjustment can be done by referring to
“Sub Clock Adjust” of <Clock & Date display type setting>
(page 29).
“-1h” / “0h” / “+1h”
Sets the date display mode.
7 types
“Date Mode”
(
: Factory setting)
4 Set the Clock & Date setting items
Turn the Control knob to select desired value,
and then press the Control knob.
The previous item is displayed.
5 Exit Function setting mode
Press the [
] button for at least 1 second.
English
|
29
General operation
Function of KDC-5751SD, KDC-5051U
Muting the audio upon reception of
phone call
Auxiliary input display setting
Sets the display when switched to AUX source.
1 Select the AUX source
Press the [SRC] button.
Select the “AUX” display.
The audio system automatically mutes when a call
comes in.
When a call comes in
“CALL” is displayed.
The audio system pauses.
2 Enter Function setting mode
Press the Control knob for at least 1 second.
3 Select the Name set mode
The item can be selected and determined as
follows.
Listening to the audio during a call
Press the [SRC] button.
The “CALL” display disappears and the audio system
comes back ON.
“Settings” > “AUX Name Set”
To select the item, turn the Control knob. To
determine the item, press the Control knob.
When the call ends
Hang up the phone.
The “CALL” display disappears and the audio system
comes back ON.
4 Sets the display of the AUX source
Turn the Control knob to select Auxiliary input
display, and then press the Control knob.
Select “AUX”, “DVD”, “PORTABLE”, “GAME”, “VIDEO”, or
“TV”.
⁄
• To use the TEL Mute feature, you need to hook up the MUTE
wire to your telephone using a commercial telephone
accessory. Refer to <Connecting wires to terminals> (page
12) of Quick start guide.
5 Exit Function setting mode
Press the [
] button for at least 1 second.
|
30 KDC-BT51U/ KDC-5751SD/ KDC-5051U
“CD Read”
Sets the method for reading CD.
Initial setting
When unable to play special format CD, set
this function to“2”to force playing. Note that
some music CDs may be unplayable even
when set to“2”.
In addition, audio files cannot be played when
set to“2”. Normally, keep this set to“1”.
1: Automatically distinguishes between audio
file disc and music CD when playing disc.
2: Forces playing as music CD.
Configures initial settings of this unit.
1 Select Standby
Press the [SRC] button.
Select the “STANDBY” display.
2 Enter Function setting mode
Press the Control knob for at least 1 second.
“Built-in AMP”
“Speaker Select”
Selecting“OFF”turns off the built-in amplifier.
Turning off the built-in amplifier improves the
quality of the sound from Preout.
“ON” / “OFF”
Fine-tuning so that the System Q value is
optimal when setting the speaker type as
follows;
3 Select the Initial setting mode
Turn the Control knob to select “Initial Settings”,
and then press the Control knob.
4 Select the desired Initial setting item
Turn the Control knob to select Initial setting
item, and then press the Control knob.
“OFF”: OFF
“5/4inch”: For 5 & 4 in. speaker
“6x9/6inch”: For 6 & 6x9 in. speaker
“O.E.M.”: For the OEM speaker
Display
“Initial Settings”
“Source Select”
Overview
Select“2”to change the source selection
method. Press the [SRC] button, turn the
Control knob to select the source, and then
press the Control knob to determine it.
1 / 2
Setting the operation check sound (beep
sound) ON/OFF.
“F/W Update #.##” Upgrades the firmware.
Selecting“YES”and then pressing Control knob
starts upgrading the firmware.
For how to update the firmware, access our
web site.
“Key Beep”
“Russian”
(
: Factory setting)
“ON” / “OFF”
When this is set to ON, the following character
strings are displayed in Russian:
Folder name/ File name/ Song title/ Artist
name/ Album name/ KCA-BT200/BT300
(optional accessory)
5 Set the Initial setting item
Turn the Control knob to select desired value,
and then press the Control knob.
The previous item is displayed.
“ON” / “OFF”
6 Exit Function setting mode
“Function Language” Changes the display language of items in
Function setting.
Press the [
] button for at least 1 second.
“English” / “Français” / “Español” /
“Deutsch” / “Italiano” / “Pyccкий”
“Power OFF Wait” Setting the timer to turn this unit’s power OFF
automatically when Standby mode continues.
Using this setting can save the vehicle’s battery
power.
“OFF”: Power OFF Timer function is OFF.
“20MIN”:Turns the power OFF after 20
minutes. (Factory setting)
“40MIN”:Turns the power OFF after 40
minutes.
“60MIN”:Turns the power OFF after 60
minutes.
“Built-in AUX”
Sets whether to display AUX during source
selection.
“ON” / “OFF”
English
|
31
General operation
Demonstration mode Setting
Turning the demonstration mode ON/OFF.
1 Enter Function setting mode
Press the Control knob for at least 1 second.
2 Select the Demonstration mode
Turn the Control knob to select “DEMO Mode”,
and then press the Control knob.
3 Set the Demonstration mode
Turn the Control knob to select desired value
(“ON” or “OFF”), and then press the Control
knob.
Exit Function setting mode.
|
32 KDC-BT51U/ KDC-5751SD/ KDC-5051U
English
|
33
Function of KDC-BT51U, KCA-BT300/BT200 (Optional Accessory)
Operation of hands-free phoning
Function of KDC-BT51U
Before use
Registering cell-phone
KDC-BT51U
• If your cell-phone is not yet registered, register (pair)
it by referring to <Registering cell-phone> (page 9)
in the Quick Start Guide or <Registering cell-phone>
(page 34) in this document.
• To register a new cell-phone, you can also refer to
<Registering cell-phone> (page 34).
1 Enter Bluetooth mode
Press the [ ] button for at least 1 second.
If your cell-phone is not yet registered, the search
for a cell-phone starts with “Searching” displayed.
Paring with new cell-phone
Turn the Control knob to select “Device Search”,
and then press the Control knob.
The search for a cell-phone starts with “Searching”
displayed.
KDC-5751SD/ KDC-5051U
• If your cell-phone is not yet registered, register (pair)
it by referring to <Registering cell-phone> (page 9)
in the Quick Start Guide or <Registering Bluetooth
device> (page 44) in this document.
2 Select the used cell-phone
Turn the Control knob to select cell-phone
name, and then press the Control knob.
⁄
• For details on the Bluetooth cell-phone with the
hands-free function, see <About the Cell-phone>
(page 53).
3 Input the PIN code
Operation type
Operation
Select the numbers.
Move to the next digit.
Delete the last digit.
Transmit the PIN code.
Turn the Control knob.
Push the Control knob towards right.
Push the Control knob towards left.
Press the Control knob.
Pairing completes with “HF Connect” displayed.
⁄
• When any error code is displayed while the paring is in
progress, refer to <Troubleshooting guide> (page 54).
|
34 KDC-BT51U/ KDC-5751SD/ KDC-5051U
Receiving a call
Calling a number in the Phone book
Answering a phone call
KDC-BT51U
1 Enter Bluetooth mode
KDC-BT51U
Press the [ ] button.
KDC-5751SD KDC-5051U
Press the Control knob.
Press the [ ] button.
KDC-5751SD KDC-5051U
Press the [LOG] button for at least 1 second.
“BT MODE” is displayed.
⁄
• The following operations disconnect the line:
- Insering a CD.
2 Select the Name search mode
Turn the Control knob to select “Phone Book”,
and then press the Control knob.
- Connecting a USB device.
• The name of the calling party is displayed if it has already
been registered in the Phone Book.
3 Search for Phone book
Operation type
Select the Phone number.
Select the name.
Operation
Rejecting an incoming call
Turn the Control knob.
Push the Control knob towards right
or left.
Push the Control knob towards up
or down.
KDC-BT51U
Press the [
] button.
KDC-5751SD KDC-5051U
Select the initial.
Press the [SRC] button.
Determine the Phone number. Press the Control knob.
4 Make a call
KDC-BT51U
Press the [ ] button.
KDC-5751SD KDC-5051U
Press the Control knob.
⁄
• Pressing [DISP] button each time switches between name
and telephone number.
• During search, a non-accent character such as “u” is
searched for instead of an accent character such as “ü”.
English
|
35
Function of KDC-BT51U, KCA-BT300/BT200 (Optional Accessory)
Operation of hands-free phoning
Dialing a number
Calling a number in the call log
1 Enter Bluetooth mode
KDC-BT51U
1 Enter Bluetooth mode
KDC-BT51U
Press the [ ] button.
KDC-5751SD KDC-5051U
Press the [ ] button.
KDC-5751SD KDC-5051U
Press the [LOG] button for at least 1 second.
“BT MODE” is displayed.
Press the [LOG] button for at least 1 second.
“BT MODE” is displayed.
2 Select the Number dial mode
2 Select the call log mode
Turn the Control knob to select “Number Dial”,
and then press the Control knob.
Turn the Control knob to select “Incoming
Calls”, “Outgoing Calls”, or “Missed Calls”, and
then press the Control knob.
3 Enter a phone number
Turn the Control knob to select number, and
then Push the Control knob towards right.
“Incoming Calls”: Incoming calls
“Outgoing Calls”: Outgoing calls
“Missed Calls”: Missed calls
4 Make a call
3 Select a name or phone number
KDC-BT51U
Turn the Control knob.
Press the [ ] button.
KDC-5751SD KDC-5051U
Press the Control knob.
4 Make a call
KDC-BT51U
Press the [ ] button.
KDC-5751SD KDC-5051U
Press the Control knob.
To erase the entered phone number digit by
digit:
Push the Control knob towards left.
⁄
⁄
• Pressing [DISP] button each time switches between name
and telephone number.
• You can input a maximum of 32 (KCA-BT300/BT200)/ 25
(KDC-BT51U) digits.
• The outgoing call list, the incoming call list, and the missed
call list, are the lists of calls originated from and received
at this unit. They are not the ones stored in the cell-phone
memory.
|
36 KDC-BT51U/ KDC-5751SD/ KDC-5051U
Speed dialing (Preset dial)
Registering to the Preset dial number
list
1 Enter Bluetooth mode
KDC-BT51U
1 Enter the phone number you wish to register
Enter the phone number with reference to the
following:
Dialing a number/ Calling a number in the call log/
Calling a number in the Phone Book
Press the [ ] button.
KDC-5751SD KDC-5051U
Press the [LOG] button for at least 1 second.
“BT MODE” is displayed.
2 Select the Preset dial mode
Turn the Control knob to select “Preset Call”,
and then press the Control knob.
2 Enter Preset memory mode
Press the [PRESET] button.
3 Select a number and store it in the memory
Turn the Control knob to select memory
number (“P1” – “P6”), and then press the
Control knob for at least 2 seconds.
3 Select the number you want to recall from the
memory
Turn the Control knob to select recall number
(“P1” – “P6”), and then press the Control knob.
Cancelling the Preset memory mode
4 Make a call
Press the [
] button.
KDC-BT51U
Press the [ ] button.
KDC-5751SD KDC-5051U
Press the Control knob.
⁄
• You need to register the preset dial number. Refer to
<Registering to the Preset dial number list> (page 37).
English
|
37
Function of KDC-BT51U, KCA-BT300/BT200 (Optional Accessory)
Operation of hands-free phoning
During a call
Call waiting
Disconnecting a Call
Press the [SRC] button.
Answering another incoming call with the
current call suspended
KDC-BT51U
Switching to the Private mode
Press the [ ] button.
KDC-5751SD KDC-5051U
Push the Control knob towards right or left.
Switches between Private talk (“PRIVATE”) and
Hands-free talk each time this button is pressed.
1) Press the Control knob.
2) Turn the Control knob to select “Answer”, and
then press the Control knob.
⁄
• Depending on the type of your cell-phone, switching
to the private talk mode may select the source that was
used before commencing the hands-free connection. If
this happens, the source cannot be switched back to the
hands-free talk mode by operating this unit. Operate your
cell-phone to return to the hands-free talk mode.
Answering another Incoming call after
terminating the current call
Press the [SRC] button.
Continuing the Current Call
1) Press the Control knob.
Adjusting the voice volume during a call
Turn the Control knob.
2) Turn the Control knob to select “Reject”, and
then press the Control knob.
Answering the waiting call after terminating
the current call
KDC-BT51U
Press the [ ] button.
KDC-5751SD KDC-5051U
Press the [SRC] button.
Switching between the current call and waiting
call
Press the Control knob.
Each pressing of this knob switches the calling
party.
|
38 KDC-BT51U/ KDC-5751SD/ KDC-5051U
Clearing the Disconnection message
Making a voice dialing call
KDC-BT51U
1 Enter Bluetooth mode
KDC-BT51U
Press the [ ] button.
KDC-5751SD KDC-5051U
Press the [ ] button.
KDC-5751SD KDC-5051U
Press the [LOG] button for at least 1 second.
“HF Disconnect” disappears.
Press the [LOG] button for at least 1 second.
“BT MODE” is displayed.
2 Enter voice recognize mode
Turn the Control knob to select “Voice
Recognize”, and then press the Control knob.
3 Have the unit recognize your spoken name
Press the Control knob. If you hear a beep,
speak a registered name within 2 seconds.
4 Have the unit recognize the spoken category
When you hear a beep, speak the category
within 2 seconds.
The recognized phone number (name) is displayed.
When you want to change the displayed phone
number (name), press the [DISP] button.
5 Make a call
Press the Control knob.
⁄
• If your voice cannot be recognized, a message is displayed.
Refer to <Troubleshooting guide> (page 54).
Pressing the Control knob allows you to retry voice input.
• Both the name and category requires registration of a voice
tag. Refer to <Setting a voice command for category>
(page 49).
English
|
39
Function of KDC-BT51U, KCA-BT300/BT200 (Optional Accessory)
Operation of hands-free phoning
Displays of phone number type
(category)
The category items in the Phone Book are displayed
as follows:
Display
Information
General
“General”/
Home
Office
Mobile
Other
“Home”/
“Office”/
“Mobile”/
“Other”/
|
40 KDC-BT51U/ KDC-5751SD/ KDC-5051U
English
|
41
Function of KCA-BT300/BT200 (Optional Accessory)
Bluetooth audio operation
Before Use
Basic operation
• You need to register your Bluetooth audio player
before using it with this unit. For more details, see
<Registering Bluetooth device> (page 44).
• You need to select the Bluetooth audio player you
wish to connect. Refer to <Selecting the Bluetooth
device you wish to connect> (page 46).
Selecting Bluetooth audio source
Press the [SRC] button.
Select the “BT AUDIO EXT” display.
Pause and play
Press the [
] button.
Music search
Push the Control knob towards right or left.
⁄
• All or some of the operations above cannot be performed if
the Bluetooth audio player is not ready for remote control.
• Switching between Bluetooth audio sources does not start
or stop playback automatically. Perform the operation for
starting or stopping playback.
• Some audio players cannot be controlled remotely or
reconnected after Bluetooth disconnection. Operate the
main unit of the audio player to connect Bluetooth.
• When “2Zone” is set to “ON” and “2Zone F/R Select” is set to
“Front” of <Audio control> (page 7), Bluetooth Audio source
cannot be selected.
|
42 KDC-BT51U/ KDC-5751SD/ KDC-5051U
English
|
43
Function of KDC-BT51U, KCA-BT300/BT200 (Optional Accessory)
Bluetooth setup
4 Select the desired Bluetooth device
Registering Bluetooth device
Turn the Control knob to select Bluetooth
device, and then press the Control knob.
KDC-BT51U
To make your Bluetooth device (cell-phone) usable
with this unit, you need to register it (pairing). You
can register up to five Bluetooth devices to this unit.
Input the PIN code (steps 5).
KDC-5751SD KDC-5051U
When registering from Bluetooth devices
When “Paring Success” is displayed, PIN code input
(steps 5) is not required.
1 Turn on the this unit.
When “Pin Code NG” is displayed, press the Control
knob. Then enter the PIN code (steps 5).
2 Start registering a unit by operating the
Bluetooth device
By operating the Bluetooth device, register the
hands-free unit (pairing). Select “KENWOOD BT
CD/R-3P1”, “KCA-BT300”, or “KCA-BT200” from the list
of connected units.
5 Input the PIN code
Operation type
Select the numbers.
Move to the next digit.
Delete the last digit.
Transmit the PIN code.
Operation
Turn the Control knob.
Push the Control knob towards right.
Push the Control knob towards left.
Press the Control knob.
3 Enter a PIN code
Input the PIN code registered as mentioned in
<Registering PIN Code> (page 45).
Check that registration is complete on the
Bluetooth device.
If “Pairing Success” is displayed, registration is
complete.
6 Return to the device list
Press the Control knob.
4 By operating the Bluetooth device, start hands-
free connection.
7 Exit Bluetooth mode
Press the [SRC] button.
When registering from this unit
1 Enter Bluetooth mode
KDC-BT51U
⁄
• This unit allows up to eight digits to be input for a PIN code.
If a PIN code cannot be input from this unit, it can be input
from the Bluetooth device.
Press the [ ] button.
KDC-5751SD KDC-5051U
• If there are 5 Bluetooth devices registered, you cannot
register a new Bluetooth device.
• If the error message appears even though the PIN code is
correct, try <Registering Special bluetooth device> (page 45).
Press the [LOG] button for at least 1 second.
“BT MODE” is displayed.
2 Enter Function setting mode
Press the Control knob for at least 1 second.
3 Select Bluetooth device registration mode
The item can be selected and determined as
follows.
“Settings” > “Pairing” > “Device Registration”
To select the item, turn the Control knob. To
determine the item, press the Control knob.
Search for the Bluetooth device.
When search is completed, “Finished” is displayed.
|
44 KDC-BT51U/ KDC-5751SD/ KDC-5051U
Registering Special bluetooth device
Registering PIN Code
Allow registration of a special device that cannot be
registered normally (pairing).
By operating the Bluetooth device, specify the PIN
code necessary for registering this unit.
1 Enter Bluetooth mode
KDC-BT51U
1 Enter Bluetooth mode
KDC-BT51U
Press the [ ] button.
KDC-5751SD KDC-5051U
Press the [ ] button.
KDC-5751SD KDC-5051U
Press the [LOG] button for at least 1 second.
“BT MODE” is displayed.
Press the [LOG] button for at least 1 second.
“BT MODE” is displayed.
2 Enter Function setting mode
Press the Control knob for at least 1 second.
2 Enter Function setting mode
Press the Control knob for at least 1 second.
3 Select Special device registration mode
The item can be selected and determined as
follows.
3 Select PIN code edit mode
The item can be selected and determined as
follows.
“Settings” > “Pairing” > “SPCL Device Select”
To select the item, turn the Control knob. To
determine the item, press the Control knob.
“Settings” > “Detailed Settings” >
“PIN Code Edit”
To select the item, turn the Control knob. To
determine the item, press the Control knob.
4 Select a desired device name
Turn the Control knob to select device name,
and then press the Control knob.
If “Completed” is displayed, registration is
completed.
4 Input the PIN code
Operation type
Operation
Select the numbers.
Move to the next digit.
Delete the last digit.
Transmit the PIN code.
Turn the Control knob.
Push the Control knob towards right.
Push the Control knob towards left.
Press the Control knob.
5 Go through the procedure of <Registering
Bluetooth device> (page 44) and complete the
registration (pairing).
If “Completed” is displayed, registration is complete.
5 Exit Bluetooth mode
Press the [SRC] button.
Cancelling Bluetooth mode
Press the [SRC] button.
⁄
⁄
• By default, “0000” is specified.
• If the device name is not in the list, select “Other Phones”.
• A PIN code can be specified with up to eight digits.
English
|
45
Function of KDC-BT51U, KCA-BT300/BT200 (Optional Accessory)
Bluetooth setup
Downloading the Phone book
Selecting the Bluetooth device you
wish to connect
Download the phone book data from the cell-
phone to this unit so that you can use the Phone
Book of this unit.
When two or more Bluetooth devices have already
been registered, you need to select the Bluetooth
device you wish to use.
Downloading automatically
If the cell-phone supports a phone book
synchronization function, the phone book is
downloaded automatically after Bluetooth
connection.
1 Enter Bluetooth mode
KDC-BT51U
Press the [ ] button.
KDC-5751SD KDC-5051U
Press the [LOG] button for at least 1 second.
“BT MODE” is displayed.
⁄
• Setting on the cell-phone may be required.
• If no phone book data is found in the unit even after the
“Completed” is displayed, your cell-phone may not support
automatic download of phone book data. In this case, try
downloading manually.
2 Enter Function setting mode
Press the Control knob for at least 1 second.
3 Select Bluetooth device selection mode
The item can be selected and determined as
follows.
“Settings” > “Pairing” > “Phone Selection” (to
select the cell-phone) or “Audio Selection” (to
select the audio player)
To select the item, turn the Control knob. To
determine the item, press the Control knob.
“(name)” is displayed.
Downloading from the cell-phone manually
1 Operate the cell-phone to end the hands-free
connection.
2 Operate the cell-phone to send the phone
book data to this unit
By operating the cell-phone, download the phone
book data to this unit.
• During downloading:
“Downloading” is displayed.
• After completion of downloading:
“Completed” is displayed.
4 Select a desired Bluetooth device
Turn the Control knob to select Bluetooth
device name, and then press the Control knob.
‘✱(name)’ or ‘-(name)’ is displayed.
“✱”: The selected Bluetooth device is busy.
“-”: The selected Bluetooth device is on standby.
“ “ (blank): The Bluetooth device is deselected.
3 Operate the cell-phone to start the hands-free
connection.
Clearing the downloading completion message
Press any button.
5 Exit Bluetooth mode
Press the [SRC] button.
⁄
⁄
• Up to 1000 phone numbers can be registered for each
registered cell-phone.
• If a cell-phone is already selected, deselect it, and then
select a different one.
• Up to 32 digits can be registered for each phone number
along with up to 50* characters representing a name.
(* 50: Number of alphabetic alphabetical characters.
Fewer characters can be input depending on the type of
characters.)
• If you cannot select a device using the audio player,
connect the device with the audio player.
• To cancel downloading of the phone book data, operate
the cell-phone.
|
46 KDC-BT51U/ KDC-5751SD/ KDC-5051U
Deleting a registered Bluetooth
device
Displaying the firmware version
Display the version of the firmware of this unit.
You can delete a registered Bluetooth device.
1 Enter Bluetooth mode
KDC-BT51U
1 Enter Bluetooth mode
KDC-BT51U
Press the [ ] button.
KDC-5751SD KDC-5051U
Press the [ ] button.
KDC-5751SD KDC-5051U
Press the [LOG] button for at least 1 second.
“BT MODE” is displayed.
Press the [LOG] button for at least 1 second.
“BT MODE” is displayed.
2 Enter Function setting mode
Press the Control knob for at least 1 second.
2 Enter Function setting mode
Press the Control knob for at least 1 second.
3 Select Bluetooth firmware update mode
The item can be selected and determined as
follows.
“Settings” > “Detailed Settings” >
“BT F/W Update”
To select the item, turn the Control knob. To
determine the item, press the Control knob.
The firmware version appears.
3 Select Bluetooth device deletion mode
The item can be selected and determined as
follows.
“Settings” > “Pairing” > “Device Delete”
To select the item, turn the Control knob. To
determine the item, press the Control knob.
Device name is displayed.
4 Exit Bluetooth mode
4 Delete the selected Bluetooth device
Turn the Control knob to select device name,
and then press the Control knob.
Press the [SRC] button.
⁄
• For how to update the firmware, access our web site.
5 Turn the Control knob to select “YES”, and then
press the Control knob.
“Completed” is displayed.
6 Exit Bluetooth mode
Press the [SRC] button.
⁄
• When a registered cell-phone is deleted, its Phone Book,
log, SMS, and voice tag are also deleted.
English
|
47
Function of KDC-BT51U, KCA-BT300/BT200 (Optional Accessory)
Bluetooth setup
Pressing the Control knob allows you to retry voice input.
Adding a voice dialing command
Selecting “Check” (Play)
Add a voice tag to the phonebook for voice dialing.
You can register up to 35 voice tags.
6 Press the Control knob.
Play the registered voice and return to step 2.
1 Enter Bluetooth mode
KDC-BT51U
Selecting “Delete” (Delete)
Press the [ ] button.
KDC-5751SD KDC-5051U
6 Delete a voice tag
Press the Control knob.
Press the [LOG] button for at least 1 second.
“BT MODE” is displayed.
7 Turn the Control knob to select “YES”, and then
press the Control knob.
2 Enter Function setting mode
Press the Control knob for at least 1 second.
Exit Bluetooth mode
Press the [SRC] button.
3 Select Phonebook name edit mode
The item can be selected and determined as
follows.
“Settings” > “Voice Tag” > “PB Name Edit”
To select the item, turn the Control knob. To
determine the item, press the Control knob.
4 Search for the name to register
Turn the Control knob to select name, and then
press the Control knob.
If a voice tag has already been registered for a
name, “*” is displayed before the name.
5 Select a mode
Turn the Control knob.
Display
Operation
“Register”
“Check”*
“Delete”*
Register a voice tag.
Play a voice tag.
Delete a voice tag.
*Displayed only when a name for which a voice tag has
been registered is selected.
Selecting “Register” (Regist)
6 Register a voice tag (first)
Press the Control knob. When you hear a beep,
speak the voice tag within 2 seconds.
7 Confirm the voice tag (second)
Press the Control knob. When you hear a
beep, speak the same voice tag again within 2
seconds.
“Completed” is displayed.
8 Exit Function setting mode
Press the [
] button for at least 1 second.
Return to step 2. You can register another voice tag
continuously.
⁄
• If your voice cannot be recognized, a message is displayed.
(Refer to <Troubleshooting guide> (page 54))
|
48 KDC-BT51U/ KDC-5751SD/ KDC-5051U
Setting a voice command for category
Add a voice tag to the phone number category
(type) for voice calling.
1 Enter Bluetooth mode
KDC-BT51U
Press the [ ] button.
KDC-5751SD KDC-5051U
Press the [LOG] button for at least 1 second.
“BT MODE” is displayed.
2 Enter Function setting mode
Press the Control knob for at least 1 second.
3 Select Phonebook type edit mode
The item can be selected and determined as
follows.
“Settings” > “Voice Tag” > “PN Type Edit”
To select the item, turn the Control knob. To
determine the item, press the Control knob.
4 Select the category (type) you wish to set
Turn the Control knob to select category name,
and then press the Control knob.
“General”/ “Home”/ “Office”/ “Mobile”/ “Other”
5 Select a mode
Turn the Control knob.
Display
Operation
“Register”
“Check”*
“Delete”*
Register a voice tag.
Play a voice tag.
Delete a voice tag.
*KCA-BT300/BT200 only. Displayed only when a name for
which a voice tag has been registered is selected.
6 Register the category (type) by performing
steps 6 to 7 in <Adding a voice dialing
command> (page 48).
7 Exit Bluetooth mode
Press the [SRC] button.
⁄
• Set the voice tag for all the 5 categories. If the voice tag is
not registered for all the categories, the Phonebook may
not be recalled by voice command.
English
|
49
Function of KDC-BT51U, KCA-BT300/BT200 (Optional Accessory)
Bluetooth setup
“MIC Gain”
Adjusts the sensitivity of the built-in
microphone for a telephone call. Adjust the
voice of caller. Setting to“+”increases the
voice volume.
Function of the KDC-BT51U
“-3” – ”0” – “+3”
Bluetooth detail setting
Configures initial settings of this unit.
1 Enter Bluetooth mode
KDC-BT51U
Press the [ ] button.
KDC-5751SD KDC-5051U
“NR Level”
SReduces the noises generated by surrounding
environment without changing the built-in
microphone volume. Adjust the voice of caller
when it is not clear. Setting to“+”increases
the noise reduction.
Press the [LOG] button for at least 1 second.
“BT MODE” is displayed.
Function of the KDC-BT51U
“-3” – ”0” – “+3”
Sets the echo cancellation level.
Function of the KDC-BT51U
“-2” – ”0” – “+2”
2 Enter Function setting mode
Press the Control knob for at least 1 second.
“Echo Cancel”
3 Select Bluetooth detail setting mode
The item can be selected and determined as
follows.
(
: Factory setting)
“Settings” > “Detailed Settings”
To select the item, turn the Control knob. To
determine the item, press the Control knob.
5 Set the Bluetooth detail setting item
Turn the Control knob to select desired value,
and then press the Control knob.
The previous item is displayed.
4 Select the desired Bluetooth detail setting
item
Turn the Control knob to select Bluetooth detail
setting item, and then press the Control knob.
6 Exit Function setting mode
Press the [
] button for at least 1 second.
Display
Overview
“Detailed Settings”
“Auto Answer”
This function automatically answers (responds
to) a call after lapse of the preset time interval
for automatic answer.
“OFF”: Does not answer the phone call
automatically.
“0”: Automatically answers the phone call
at once.
“1SEC” – “8SEC” – “99SEC”:
Automatically answers the phone call after
lapse of 1 – 99 seconds.
“Auto Reconnect” When“ON”is selected, re-pairing with the
registered Bluetooth device starts automatically
when pairing is disconnected.
“ON” / “OFF”
“Bluetooth HF”
“Bluetooth HF/
Audio”
You can specify output speakers for hands-free
voice communication and Bluetooth audio
sound.
“Front” : Outputs sound from the front
speakers.
“All” : Outputs sound from the front and rear
speakers.
“Call Beep”
You can output a beep from the speaker when
a call comes in.
“ON” : Beep is heard.
“OFF” : Beep is canceled.
|
50 KDC-BT51U/ KDC-5751SD/ KDC-5051U
Function of KDC-BT51U, KCA-BT300/BT200 (Optional Accessory)
SMS (Short Message Service)
Displaying the SMS
Downloading the SMS
The SMS received by at the cell-phone is displayed
on the receiver.
Download the short message (SMS) received by the
cell-phone so that it can be read on this unit.
A newly received message is displayed.
1 Enter Bluetooth mode
KDC-BT51U
¤
• To prevent car accidents, the driver should not read the
Press the [ ] button.
KDC-5751SD KDC-5051U
SMS while driving.
Press the [LOG] button for at least 1 second.
“BT MODE” is displayed.
When a new message arrives
“SMS Received” is displayed.
The display disappears with any operations.
2 Enter Function setting mode
Press the Control knob for at least 1 second.
Displaying the SMS
3 Select SMS download mode
The item can be selected and determined as
follows.
1 Enter Bluetooth mode
KDC-BT51U
Press the [ ] button.
KDC-5751SD KDC-5051U
“Settings” > “SMS Download”
To select the item, turn the Control knob. To
determine the item, press the Control knob.
Press the [LOG] button for at least 1 second.
2 Select SMS inbox display mode
Turn the Control knob to select “SMS Inbox”,
and then press the Control knob.
4 Start downloading
Press the Control knob.
“SMS Downloading” is displayed.
When the downloading finishes, “Completed” is
displayed.
3 Select a message
Turn the Control knob.
Each press of the [DISP] button switches between
displaying the telephone number or name and
message reception date.
5 Exit Bluetooth mode
Press the [SRC] button.
⁄
4 Display the text
• The cell-phone must be able to transmit the SMS using
Bluetooth. Setting on the cell-phone may be required. If
the cell-phone does not support SMS function, the SMS
download item in Function Control mode is not displayed.
• When the SMS is downloaded from the cell-phone, the
unopened messages in the cell-phone are opened.
• The up to 75 already-read and unread short messages
respectively can be downloaded.
Press the Control knob.
Turn the Control knob to scroll through the
message.
Press the Control knob to return to the message
list screen.
5 Exit Bluetooth mode
Press the [SRC] button.
⁄
• The unopened message is displayed at the beginning of the
list. Other messages are displayed in the order of reception.
• The SMS that are received when the cell-phone is not linked
with Bluetooth cannot be displayed. Download the SMS.
• The short message cannot be displayed during
downloading the SMS.
English
|
51
Appendix
About Audio file
About USB device
•
•
•
•
•
Playable Audio file
• When the USB device is connected to this unit,
it can be charged up provided that this unit is
powered.
AAC-LC (.m4a), MP3 (.mp3), WMA (.wma)
Playable disc media
CD-R/RW/ROM
Playable disc file format
ISO 9660 Level 1/2, Joliet, Romeo, Long file name.
Playable USB device
USB mass storage class
Playable USB device and SD card file system
• Install the USB device in the place where it will not
prevent you from driving your vehicle properly.
• You cannot connect a USB device via a USB hub and
Multi Card Reader.
• Save backups of the audio files used with this unit.
The files can be erased depending on the operating
conditions of the USB device.
We shall have no compensation for any damage
arising out of erasure of the stored data.
• No USB device comes with this unit. You need to
purchase a commercially available USB device.
• When connecting the USB device, usage of the
CA-U1EX (option) is recommended.
• Normal playback is not guaranteed when a cable
other than the USB compatible cable is used.
Connecting a cable whose total length is longer
than 4 m can result in abnormal playback.
FAT16, FAT32
Even if the audio files comply with the standards listed
above, the play may be impossible depending on the
types or conditions of media or device.
•
Playing order of the Audio file
In the example of folder/file tree shown below, the
files are played in the order from ① to ⑩.
^
¡
: Folder
Folder
CD
(1)
:
A
udiofile
¡!
2
3
¡"
¡#
iPod/iPhone that can be connected to this
unit
Made for
• iPod nano (6th generation) • iPod nano (5th generation)
• iPod nano (4th generation) • iPod nano (3rd generation)
• iPod nano (2nd generation) • iPod nano (1st generation)
• iPod with video
• iPod touch (4th generation) • iPod touch (3rd generation)
• iPod touch (2nd generation) • iPod touch (1st generation)
4
¡$
5
¡%
¡P
• iPod classic
An online manual about audio files is put on the site,
www.kenwood.com/cs/ce/audiofile/. On this online
manual, detailed information and notes which are not
written in this manual are provided. Make sure to read
through the online manual as well.
• iPhone 4
• iPhone 3G
• iPhone 3GS
• iPhone
• For information on the compatibility of iPod/iPhone
• Type of control available varies depending
on the type of connected iPod. See
www.kenwood.com/cs/ce/ipod/ for further details.
• The word “iPod” appearing in this manual indicates
the iPod or the iPhone connected with the iPod
connection cable* (optional accessory).
* Not supported model KCA-iP500.
• Refer to the web site for connectable iPod and iPod
connection cable.
⁄
• In this manual, the word “USB device” is used for flash
memories and digital audio players which have USB
terminals.
About SD card
• This unit is capable of playback of SD/SDHC
memory cards complying with the SD or SDHC
standard.
SD card (≤2 GB), SDHC card (≤32 GB)
• A special adapter is required to use a miniSD card,
miniSDHC card, microSD card or microSDHC card.
• The MultiMedia Card (MMC) cannot be used.
• Data recorded in the SD audio format cannot be
played back.
⁄
• If you start playback after connecting the iPod, the music
that was playing on the iPod is played first.
In this case, “RESUMING” is displayed without displaying a
folder name, etc. Changing the browse item will display a
correct title, etc.
• You cannot operate iPod if “KENWOOD” or “✓” displayed on
iPod.
|
52 KDC-BT51U/ KDC-5751SD/ KDC-5051U
Function of KDC-BT51U
About “KENWOOD Music Editor”
• This unit supports the PC application “KENWOOD
Music Editor Light ver1.1” or later.
• When you use the audio file with database
information added by the “KENWOOD Music Editor
Light ver1.1”, you can search a file by title, album or
artist name using the <Music search> (page 14).
About the Cell-phone
This unit conforms to the following Bluetooth
specifications:
Version
Profile
Bluetooth Ver. 2.0 Certified
HFP (Hands Free Profile)
HSP (Headset Profile)
SPP (Serial Port Profile)
• In the Instruction manual, the term “Music Editor
media” is used to mean the device that contains
audio files with database information added with
KENWOOD Music Editor.
PBAP (Phonebook Access Profile)
OPP (Object Push Profile)
SYNC (Synchronization Profile)
• “KENWOOD Music Editor Light ver1.1” is available
from the following web site:
• For further information on “KENWOOD Music
Editor Light ver1.1”, refer to the site above or the
application help.
For the cell-phones verified for compatibility, access
the following URL:
⁄
• The units supporting the Bluetooth function have been
certified for conformity with the Bluetooth Standard
following the procedure prescribed by Bluetooth
SIG. However, it may be impossible for such units to
communicate with your cell-phone depending on its type.
• HFP is a profile used to make a hands-free call.
• OPP is a profile used to transfer data such as a phone book
between units.
English
|
53
Troubleshooting guide
Some functions of this unit may be disabled by
some settings made on this unit.
The messages shown below display your
systems condition.
TOC Error:
• No disc has been loaded in the disc
magazine.
• The CD is quite dirty. The CD is upside-
down. The CD is scratched a lot.
!
!
• Cannot set up Display.
<Demonstration mode Setting> (page 32) is not set to
Off.
Error 05:
Error 77:
The disc is unreadable.
• Cannot set up “Text Select”, “Side Select”, and
“Status” of “Display Select”.
<Selecting display type> (page 24) is set to Displays
The unit is malfunctioning for some reason.
Press the reset button on the unit. If the
“Error 77” code does not disappear, consult
your nearest service center.
off.
!
!
• Cannot set up the subwoofer.
• Cannot set up the low pass filter.
• No output from the subwoofer.
“SubWoofer” of <Audio control> (page 7) is not set to
On.
Mecha Error: Something is wrong with the disc magazine.
Or the unit is malfunctioning for some reason.
Check the disc magazine. And then press
the reset button on the unit. If the “Mecha
Error” code does not disappear, consult
your nearest service center.
Cannot set up the subwoofer Phase.
“LPF SubWoofer” of <Audio control> (page 7) is set to
“Through”.
IN (Blink):
The CD player section is not operating
properly.
Reinsert the CD. If the CD cannot be
ejected or the display continues to flash
even when the CD has been properly
reinserted, please switch off the power
and consult your nearest service center.
What might seem to be a malfunction in your unit
may just be the result of slight misoperation or
miswiring. Before calling service, first check the
following table for possible problems.
Protect (Blink): The speaker wire has a short-circuit or
touches the chassis of the vehicle, and then
the protection function is activated.
General
? The Key beep does not sound
Wire or insulate the speaker cable properly
and press the reset button. If the “Protect”
code does not disappear, consult your
nearest service center.
The preout jack is being used.
The Key beep cannot be output from the preout
jack.
NA File:
An Audio file is played with a format that this
unit can’t support.
Tuner source
? Radio reception is poor.
Copy PRO:
Read Error:
A copy-protected file is played.
The car antenna is not extended.
Pull the antenna out all the way.
The file system of the connected USB device
is broken.
Copy the files and folders for the USB
device again. If the error message is still
displayed, initialize the USB device or use
other USB devices.
Disc source
? The specified disc does not play, but another one
plays instead.
The specified CD is quite dirty.
Clean the CD, referring to the CD cleaning of the
section on <Handling discs> (page 4).
No Device:
N/A Device:
The USB device is selected as a source
although no USB device is connected.
Change the source to any source other
than USB. Connect an USB device, and
change the source to USB again.
The disc is severely scratched.
Try another disc instead.
Audio file source
• An unsupported USB device is connected.
• Connection to the iPod has failed.
Check that the connected iPod is an iPod
that is supported. See <About Audio file>
(page 52) for information on supported
iPods.
? The sound skips when an Audio file is being
played.
The media is scratched or dirty.
Clean the media, referring to the CD cleaning of
the section on <Handling discs> (page 4).
The recording condition is bad.
Record the media again or use another media.
|
54 KDC-BT51U/ KDC-5751SD/ KDC-5051U
No Music Data/Error 15:
• The connected USB device contains no
Too Long:
The word or utterance is too long to be
recognized.
playable audio file.
• Media was played that does not have data
recorded that the unit can play.
No Phonebook: Data is not contained in the phone book.
No Message: No short message in In Box.
USB ERROR:
iPod Error:
Some trouble may have occurred to the
connected USB device.
Remove the USB device, then cycle the
power switch to ON. If the same display is
repeated, use another USB device.
No Record:
The voice tag is not registered in the
phonebook.
Memory Full: The number of voice tags reaches the
maximum number to be registered in the
phonebook.
Connection to the iPod has failed.
Remove the USB device and then
reconnect it.
Confirm that the software for the iPod is
the latest version.
LOG: No Memory:
The procedure is not registered to Log Preset
Memory.
No Access:
The procedure preset with Log Preset
Memory cannot be available. The preset
content may not be recalled depending on
the selected source or mode.
Reset iPod/ iPhone.
No Number:
No Data:
• The calling party does not notify a caller ID.
• There is no phone number data.
• There is no outgoing call list.
• There is no incoming call list.
• There is no missed call list.
• There is no phone book list.
No Voice:
No call.
Memory Full: The tag memory of HD Radio is FULL.
iPod Full: The iPod memory is FULL.
No Entry:
The cell-phone has not been registered
(pairing).
N/A Channels: No receivable channel and category.
HF Disconnect: The unit cannot communicate with the cell-
phone.
HF Error 07:
The memory cannot be accessed.
Turn off the power and on again. If this
message still appears, press the reset
button on the control unit.
HF Error 68:
The unit cannot communicate with the cell-
phone.
Turn off the power and on again. If this
message still appears, press the reset
button on the control unit.
Unknown:
The Bluetooth device cannot be detected.
Device Full:
5 Bluetooth device have already been
registered. No more Bluetooth devices are
registered.
PIN Code NG: The PIN code is wrong.
Connect NG: The unit cannot be connected to the device.
Pairing Failed: Pairing error.
Err No Matching:
The voice tag is wrong. Voice cannot be
recognized because of an unregistered voice
tag, etc.
Too Soft:
Voice is too small and cannot be recognized.
Voice is too large to be recognized.
Too Loud:
English
|
55
Specifications
FM tuner section
USB Interface
Frequency range (50 kHz step)
: 87.5 MHz – 108.0 MHz
USB Standard
: USB1.1/ 2.0 (Full speed)
Usable sensitivity (S/N = 26dB)
: 1 μV/75 Ω
File System
: FAT16/ 32
Quieting Sensitivity (S/N = 46dB)
: 2.5 μV/75 Ω
Maximum Supply current
: 500 mA
Frequency response ( 3.0 dB)
: 30 Hz – 15 kHz
MP3 decode
: Compliant with MPEG-1/2 Audio Layer-3
Signal to Noise ratio (MONO)
: 63 dB
WMA decode
: Compliant with Windows Media Audio
Stereo separation (1 kHz)
: 40 dB
AAC decode
: AAC-LC “.m4a” files
MW tuner section
Bluetooth section (KDC-BT51U)
Frequency range (9 kHz step)
: 531 kHz – 1611 kHz
Version
: Bluetooth Ver. 2.0 Certified
Usable sensitivity (S/N = 20dB)
: 36 µV
Frequency range
: 2.402 – 2.480 GHz
Output Power
: +4dBm (MAX), 0dBm (AVE) Power Class 2
Maximum Communication range
: Line of sight approx.10m (32.8 ft)
Profiles
: HFP (Hands Free Profile)
: HSP (Headset Profile)
LW tuner section
Frequency range
: 153 kHz – 279 kHz
Usable sensitivity (S/N = 20dB)
: 57 µV
: SPP (Serial Port Profile)
CD player section
Laser diode
: GaAlAs
Digital filter (D/A)
: 8 Times Over Sampling
D/A Converter
: 24 Bit
Spindle speed
: 500 – 200 rpm (CLV)
Wow & Flutter
: Below Measurable Limit
Frequency response ( 1 dB)
: 10 Hz – 20 kHz
Total harmonic distortion (1 kHz)
: 0.008 %
Signal to Noise ratio (1 kHz)
: 110 dB
: PBAP (Phonebook Access Profile)
: OPP (Object Push Profile)
: SYNC (Synchronization Profile)
Audio section
Maximum output power
: 50 W x 4
PWR DIN45324,+B=14.4V
: 30 W x 4
Speaker Impedance
: 4 – 8 Ω
Tone action
Bass : 100 Hz 8 dB
Middle : 1 kHz 8 dB
Treble : 12.5 kHz 8 dB
Preout level / Load (CD)
: 2500 mV/10 kΩ
Preout impedance
: ≤ 600 Ω
Dynamic range
: 93 dB
MP3 decode
: Compliant with MPEG-1/2 Audio Layer-3
WMA decode
: Compliant with Windows Media Audio
AAC decode
: AAC-LC “.m4a” files
|
56 KDC-BT51U/ KDC-5751SD/ KDC-5051U
Auxiliary input
Frequency response ( 3 dB)
: 20 Hz – 20 kHz
Input Maximum Voltage
: 1200 mV
Input Impedance
: 10 kΩ
General
Operating voltage
KDC-BT51U : 14.4 V (10.5 – 16V allowable)
KDC-5751SD/ KDC-5051U
: 14.4 V (11 – 16V allowable)
Maximum Current consumption
: 10 A
Installation Size (W x H x D)
: 182 x 53 x 160 mm
Weight
: 1.3 kg
Specifications subject to change without notice.
English
|
57
This Product is not installed by the manufacturer of a
vehicle on the production line, nor by the professional
importer of a vehicle into an EU Member State.
• The Bluetooth word mark and logos are owned by
the Bluetooth SIG, Inc. and any use of such marks
by Kenwood Corporation is under license. Other
trademarks and trade names are those of their
respective owners.
Information on Disposal of Old Electrical and
Electronic Equipment and Batteries (applicable
for EU countries that have adopted separate
waste collection systems)
• The “AAC” logo is a trademark of Dolby Laboratories.
• iTunes is a trademark of Apple Inc.
• “Made for iPod” and “Made for iPhone” mean that an
electronic accessory has been designed to connect
specifically to iPod or iPhone, respectively, and has
been certified by the developer to meet Apple
performance standards. Apple is not responsible for
the operation of this device or its compliance with
safety and regulatory standards. Please note that the
use of this accessory with iPod or iPhone may affect
wireless performance.
• iPhone, iPod, iPod classic, iPod nano, and iPod touch
are trademarks of Apple Inc., registered in the U.S. and
other countries.
• “Adobe Reader” is a trademark of Adobe Systems
Incorporated.
Products and batteries with the symbol (crossed-
out wheeled bin) cannot be disposed as
household waste.
Old electrical and electronic equipment and
batteries should be recycled at a facility capable
of handling these items and their waste
byproducts.
Contact your local authority for details in locating
a recycle facility nearest to you.
Proper recycling and waste disposal will help
conserve resources whilst preventing detrimental
effects on our health and the environment.
Notice: The sign “Pb” below the symbol for
batteries indicates that this battery
contains lead.
• SDHC Logo is a trademark of SD-3C, LLC.
The marking of products using lasers
CLASS 1
LASER PRODUCT
The label is attached to the chassis/case and says
that the component uses laser beams that have been
classified as Class 1. It means that the unit is utilizing
laser beams that are of a weaker class. There is no
danger of hazardous radiation outside the unit.
This symbol mark indicates that Kenwood
manufactured this product so as to
decrease harmful influence on the
environment.
Magyar
Declaration of Conformity with regard to
the EMC Directive 2004/108/EC
•
Alulírott, Kenwood, kijelenti, hogy a jelen KDC-BT51U megfelel az 1999/5/EC
irányelvben meghatározott alapvető követelményeknek és egyéb vonatkozó
előírásoknak.
Svenska
For KDC-BT51U:
Declaration of Conformity with regard to
the R&TTE Directive 1999/5/EC
Manufacturer:
Kenwood Corporation
2967-3 Ishikawa-machi, Hachioji-shi, Tokyo, 192-8525 Japan
•
Härmed intygar Kenwood att denna KDC-BT51U stär l överensstämelse med de
väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av
direktiv 1999/5/EG.
Suomi
•
Kenwood vakuuttaa täten että KDC-BT51U tyyppinen laite on direktiivin
1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen
mukainen.
EU Representative's:
Kenwood Electronics Europe BV
Amsterdamseweg 37, 1422 AC UITHOORN, The Netherlands
Slovensko
•
S tem Kenwood izjavlja, da je ta KDC-BT51U v skladu z osnovnimi zahtevami in
ostalimi ustreznimi predpisi Direktive 1999/5/EC.
Slovensky
•
Spoločnosť Kenwood týmto vyhlasuje, že KDC-BT51U spĺňa zákldné požiadavky
a ďalšie prislušné ustanovenia Direktĺvy 1999/5/EC.
English
Dansk
Undertegnede Kenwood erklærer harved, at følgende udstyr KDC-BT51U
overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.
Ελληνικά
ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Kenwood ΔΗΛΩΝΕΙ ΟΤΙ KDC-BT51U ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ
ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ
1999/5/EK.
•
Hereby, Kenwood declares that this unit KDC-BT51U is in compliance with the
essential requirements and other relevant provisions of Directive 1999/5/EC.
•
Français
•
Par la présente Kenwood déclare que l’appareil KDC-BT51U est conforme aux
exigences essentielles et aux autres dispositions pertinentes de la directive
1999/5/CE.
•
•
Par la présente, Kenwood déclare que ce KDC-BT51U est conforme aux
exigences essentielles et aux autres dispositions de la directive 1999/5/CE qui
lui sont applicables.
Eesti
Sellega kinnitab Kenwood, et see KDC-BT51U vastab direktiivi 1999/5/EC
põhilistele nõudmistele ja muudele asjakohastele määrustele.
•
Deutsch
Latviešu
•
Hiermit erklärt Kenwood, dass sich dieser KDC-BT51U in Übereinstimmung mit
den grundlegenden Anforderungen und den anderen relevanten Vorschriften
der Richtlinie 1999/5/EG befindet. (BMWi)
•
Ar šo, Kenwood, apstiprina, ka KDC-BT51U atbilst Direktīvas 1999/5/EK
galvenajām prasībām un citiem tās nosacījumiem.
Lietuviškai
•
Hiermit erklärt Kenwood die Übereinstimmung des Gerätes KDC-BT51U mit den
grundlegenden Anforderungen und den anderen relevanten Festlegungen der
Richitlinie 1999/5/EG. (Wien)
•
Šiuo, Kenwood, pareiškia, kad šis KDC-BT51U atitinka pagrindinius Direktyvos
1999/5/EB reikalavimus ir kitas svarbias nuostatas.
Malti
Nederlands
•
Hawnhekk, Kenwood, jiddikjara li dan KDC-BT51U jikkonforma mal-ħtiġijiet
essenzjali u ma provvedimenti oħrajn relevanti li hemm fid-Dirrettiva 1999/5/
EC.
•
Hierbij verklaart Kenwood dat het toestel KDC-BT51U in overeenstemming
is met de essentiële eisen en de andere relevante bepalingen van richtlijn
1999/5/EG.
Українська
•
Bij deze verklaat Kenwood dat deze KDC-BT51U voldoet aan de essentiële eisen
en aan de overige relevante bepalingen van Richtlijn 1999/5/EC.
•
Компанія Kenwood заявляє, що цей виріб KDC-BT51U відповідає ключовим
вимогам та іншим пов’язаним положенням Директиви 1999/5/EC.
Italiano
Turkish
•
Con la presente Kenwood dichiara che questo KDC-BT51U è conforme ai
requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva
1999/5/CE.
•
Kenwood, işbu belge ile KDC-BT51U numaralı bu ünitenin 1999/5/EC
Direktifi’nin özel gereksinimlerine ve ilgili diğer hükümlerine uygun olduğunu
beyan eder.
Español
•
Por medio de la presente Kenwood declara que el KDC-BT51U cumple con los
requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de
la Directiva 1999/5/CE.
Português
•
Kenwood declara que este KDC-BT51U está conforme com os requisitos
essenciais e outras disposições da Directiva 1999/5/CE.
Polska
For Turkey
•
Kenwood niniejszym oświadcza, że KDC-BT51U spełnia zasadnicze wymogi
oraz inne istotne postanowienia dyrektywy 1999/5/EC.
Bu ürün 26891sayılı Resmi Gazete’de yayımlanan Elektrikli
ve Elektronik Eşyalarda Bazı Zararlı Maddelerin Kullanımının
Sınırlandırılmasına Dair Yönetmeliğe uygun olarak üretilmiştir.
Český
Kenwood timto prohlasuje, ze KDC-BT51U je ve shode se zakladnimi pozadavky
a s dalsimi prislusnymi ustanoveni Narizeni vlady c. 426/2000 Sb.
•
This product complies with Directive, Number 26891
regarding “REGULATION ON THE RESTRICTION OF THE USE
OF CERTAIN HAZARDOUS SUBSTANCES IN LECTRICAL AND
ELECTRONIC EQUIPMENT”.
|