Kenwood DDX5022 User Manual

MONITOR WITH DVD RECEIVER  
DDX5022  
DDX5022Y  
DDX52RY  
INSTALLATION MANUAL  
© B54-4621-00/00 (EW/E2W/E3W)  
Installation Procedure  
1. To prevent short circuits, remove the key from the  
ignition and disconnect the - terminal of the  
battery.  
2. Make the proper input and output wire  
connections for each unit.  
3. Connect the wire on the wiring harness.  
4. Take Connector B on the wiring harness and  
connect it to the speaker connector in your vehicle.  
5. Take Connector A on the wiring harness and  
connect it to the external power connector on your  
vehicle.  
6. Connect the wiring harness connector to the unit.  
7. Install the unit in your car.  
8. Reconnect the - terminal of the battery.  
9. Press the reset button.  
¤
Mounting and wiring this product requires skills and  
experience. For safety’s sake, leave the mounting and wiring  
work to professionals.  
Make sure to ground the unit to a negative 12V DC power  
supply.  
Do not install the unit in a spot exposed to direct sunlight  
or excessive heat or humidity. Also avoid places with too  
much dust or the possibility of water splashing.  
Do not use your own screws. Use only the screws provided.  
If you use the wrong screws, you could damage the unit.  
If the power is not turned ON (“PROTECT” is displayed),  
the speaker wire may have a short-circuit or touched the  
chassis of the vehicle and the protection function may  
have been activated. Therefore, the speaker wire should be  
checked.  
Make sure that all wire connections are securely made by  
inserting jacks until they lock completely.  
2WARNING  
If your vehicle’s ignition does not have an ACC position, or  
if the ignition wire is connected to a power source with  
constant voltage such as a battery wire, the power will not  
be linked with the ignition (i.e., it will not turn on and off  
along with the ignition). If you want to link the unit’s power  
with the ignition, connect the ignition wire to a power  
source that can be turned on and off with the ignition key.  
Use a commercially available conversion connector if the  
connector does not fit in the vehicle connector.  
Insulate unconnected wires with vinyl tape or other similar  
material. To prevent a short circuit, do not remove the caps  
on the ends of the unconnected wires or the terminals.  
If the console has a lid, make sure to install the unit so that  
the faceplate will not hit the lid when closing and opening.  
If the fuse blows, first make sure the wires aren’t touching  
to cause a short circuit, then replace the old fuse with one  
with the same rating.  
If you connect the ignition wire (red) and the battery wire  
(yellow) to the car chassis (ground), you may cause a short  
circuit, that in turn may start a fire. Always connect those  
wires to the power source running through the fuse box.  
Connect the speaker wires correctly to the terminals to  
which they correspond. The unit may be damaged or fail to  
work if you share the - wires or ground them to any metal  
part in the car.  
After the unit is installed, check whether the brake lamps,  
blinkers, wipers, etc. on the car are working properly.  
Mount the unit so that the mounting angle is 30° or less.  
This unit has the cooling fan (page 5) to decrease the  
internal temperature. Do not mount the unit in a place  
where the cooling fan of the unit are blocked. Blocking  
these openings will inhibit the cooling of the internal  
temperature and result in malfunction.  
Do not press hard on the panel surface when installing the  
unit to the vehicle. Otherwise scars, damage, or failure may  
result.  
|
English  
3
Connection  
Connector A  
Ground wire (Black)  
Battery wire (Yellow)  
Ignition wire (Red)  
8
7
6
5
4
3
2
1
8
7
6
5
4
3
2
1
Connector B  
Antenna Cord  
(Orange/White)  
Dimmer control wire (Orange/White)  
ILLUMI  
Connect to the vehicle's parking  
brake detection switch harness.  
Parking sensor wire (Light Green)  
PRK SW  
For the sake of safety, be sure to connect the parking sensor.  
Reveres sensor wire (Purple/White)  
Connect to vehicle's reverse lamp harness when  
using the optional rear view camera.  
Steering remote control input  
(Light Blue/Yellow)  
To steering remote  
To use the steering wheel remote control feature, you need to an  
exclusive remote adapter (not supplied) matches your car is required.  
When this terminal is not in use, leave its cap on.  
Mute wire (Brown)  
Connect to the terminal that is grounded when either  
the telephone rings or during conversation.  
To connect the Kenwood navigation system,  
consult your navigation manual.  
Power control/ Motor antenna control wire  
(Blue/White)  
Connect either to the power control terminal when using the optional  
power amplifier, or to the antenna control terminal in the vehicle.  
If no connections are made, do not let the cable come out from the tab.  
|
4
DDX5022/DDX5022Y/DDX52RY  
Cooling fan  
FM/AM antenna input (JASO)  
Wiring harness  
(Accessory 1)  
FUSE ( 15A )  
REVERSE  
REMO.CONT  
MUTE  
ANT. CONT  
P CONT  
|
English  
5
Connecting Wires to Terminals  
Connector Function Guide  
Pin Numbers for Cable Colour  
ISO Connectors  
External Power  
Connector  
2WARNING  
Functions  
Connecting the ISO Connector  
The pin arrangement for the ISO connectors depends on  
the type of vehicle you drive. Make sure to make the proper  
connections to prevent damage to the unit.  
A-4  
A-5  
A-6  
A-7  
A-8  
Yellow  
Battery  
Power Control  
Dimmer  
Ignition (ACC)  
Earth (Ground)  
Connection  
The default connection for the wiring harness is described in  
1 below. If the ISO connector pins are set as described in 2  
or 3, make the connection as illustrated.  
Please be sure to reconnect the cable as shown 2 below to  
install this unit to the Volkswagen vehicles etc.  
Blue/White  
Orange/White  
Red  
Black  
Speaker  
Connector  
B-1  
B-2  
B-3  
B-4  
B-5  
B-6  
B-7  
1(Default setting) The A-7 pin of the vehicle’s ISO  
connector is linked with the ignition, and the A-4  
pin is connected to the constant power supply.  
Purple  
Purple/Black  
Gray  
Gray/Black  
White  
White/Black  
Green  
Rear Right (+)  
Rear Right (–)  
Front Right (+)  
Front Right (–)  
Front Left (+)  
Front Left (–)  
Rear Left (+)  
Rear Left (–)  
Ignition cable (Red)  
Unit  
Battery cable (Yellow)  
A-7 Pin  
Vehicle  
A-4 Pin  
B-8  
Green/Black  
2The A-7 pin of the vehicle’s ISO connector is  
connected to the constant power supply, and the  
A-4 pin is linked to the ignition.  
Ignition cable  
A-7 Pin  
(Red)  
Unit  
Vehicle  
Battery cable  
(Yellow)  
A-4 Pin  
3The A-4 pin of the vehicle’s ISO connector is  
not connected to anything, while the A-7 pin is  
connected to the constant power supply (or both  
the A-7 and A-4 pins are connected to the constant  
power supply).  
Ignition cable (Red)  
Unit  
Battery cable (Yellow)  
A-7 Pin  
Vehicle  
A-4 Pin  
When the connection is made as in 3 above, the unit’s  
power will not be linked to the ignition key. For that reason,  
always make sure to turn off the unit’s power when the  
ignition is turned off.  
To link the unit’s power to the ignition, connect the ignition  
cable (ACC...red) to a power source that can be turned on  
and off with the ignition key.  
|
6
DDX5022/DDX5022Y/DDX52RY  
System Connection  
USB device  
(commercially available)  
USB terminal  
Do not connect.  
Audio Input  
Resistance-free stereo type mini  
plug (3.5φ)  
Visual Input  
Resistance-free mini plug (3.5φ)  
Rear View Camera Input  
• Visual input (Yellow)  
Audio/Visual Output  
• Visual output (Yellow)  
Front Preout  
• Audio left output (White)  
• Audio right output (Red)  
Rear Preout/ Subwoofer Preout  
• Audio left output (White)  
• Audio right output (Red)  
Audio/Visual Output  
• Audio left output (White)  
• Audio right output (Red)  
|
English  
7
Optional Accessory Connection  
iPod  
(commercially available)  
KCA-iP300V  
(Optional Accessory)  
Audio Output (Black)  
Visual Output (Yellow)  
Visual Input  
(Yellow)  
USB terminal  
USB terminal  
Navigation System  
(Optional Accessory)  
Audio Input  
(Black)  
KCA-BT200 input  
(Optional Accessory)  
TV Tuner  
(Optional Accessory)  
T V A N T E N N A I N P U T  
Connection cable  
(Included in the Navigation System)  
R O U N I T  
M O O T N I T  
Connection cable  
(Included in the TV tuner)  
|
8
DDX5022/DDX5022Y/DDX52RY  
Installation for Monitor/Player Unit  
Firewall or metal support  
Screw (M4X8)  
(commercially available)  
Bend the tabs of the mounting  
sleeve with a screwdriver or similar  
utensil and attach it in place.  
Self-tapping screw  
(commercially available)  
Metal mounting strap  
(commercially available)  
Make sure that the unit is installed securely in place. If the unit is unstable,  
it may malfunction (eg, the sound may skip).  
Installing the Escutcheon  
Accessory 3  
|
English  
9
Removing Monitor/Player Unit  
Removing the Hard Rubber Frame  
(escutcheon)  
1. Engage the catch pins on the removal tool 2 and  
remove the two locks on the lower level.  
Lower the frame and pull it forward as shown in  
the figure.  
Removing the Unit  
1. Remove the hard rubber frame by referring to the  
removal procedure in the section <Removing the  
Hard Rubber Frame>.  
2. Remove the Hex-head screw with integral washer  
(M4 × 8) on the back panel.  
3. Insert the two removal tools 2 deeply into the  
slots on each side, as shown.  
Removal Tool (Accessory 2)  
Removal Tool  
(Accessory 2)  
Catch  
Lock  
The frame can be removed from the top side in the same  
manner.  
4. Lower the removal tool toward the bottom, and  
pull out the unit halfway while pressing towards  
the inside.  
2. When the lower level is removed, remove the  
upper two locations.  
Be careful to avoid injury from the catch pins on the  
removal tool.  
5. Pull the unit all the way out with your hands, being  
careful not to drop it.  
|
10  
DDX5022/DDX5022Y/DDX52RY  

Rockford Fosgate RFP 1815 User Manual
RCA CC6392 User Manual
Raypak RAYTHERM 133 4001 User Manual
Pioneer Elite BDP 95FD User Manual
PAC SWI JACK User Manual
Kenwood KFC PS1700P User Manual
Kenwood KDC HD548U User Manual
Kenwood KDC C719MP User Manual
Kenwood KDC 415UA User Manual
JVC KW AVX830 User Manual