Kenwood Car Video System KVT 829DVD User Manual

MONITOR WITH DVD RECEIVER  
KVT-829DVD  
INSTALLATION MANUAL  
© B54-4555-00/00 (EV)  
Installation Procedure  
1. To prevent short circuits, remove the key from the  
ignition and disconnect the - terminal of the  
battery.  
2. Make the proper input and output wire  
connections for each unit.  
¤
If the power is not turned ON (or it is ON, but will be OFF  
immediately), the speaker wire may have a short-circuit  
or touched the chassis of the vehicle and the protection  
function may have been activated. Therefore, the speaker  
wire should be checked.  
3. Connect the wire on the wiring harness.  
4. Take Connector B on the wiring harness and  
connect it to the speaker connector in your vehicle.  
5. Take Connector A on the wiring harness and  
connect it to the external power connector on your  
vehicle.  
6. Connect the wiring harness connector to the unit.  
7. Install the unit in your car.  
8. Reconnect the - terminal of the battery.  
9. Press the reset button.  
If your car is not prepared for this special connection-  
system, consult your Kenwood dealer.  
Only use antenna conversion adapters (ISO-JASO) when the  
antenna cord has an ISO plug.  
Make sure that all wire connections are securely made by  
inserting jacks until they lock completely.  
If your vehicle’s ignition does not have an ACC position, or  
if the ignition wire is connected to a power source with  
constant voltage such as a battery wire, the power will not  
be linked with the ignition (i.e., it will not turn on and off  
along with the ignition). If you want to link the unit’s power  
with the ignition, connect the ignition wire to a power  
source that can be turned on and off with the ignition key.  
If the fuse blows, first make sure that the wires have not  
caused a short circuit, then replace the old fuse with one  
with the same rating.  
2WARNING  
If you connect the ignition wire (red) and the battery wire  
(yellow) to the car chassis (ground), you may cause a short  
circuit, that in turn may start a fire. Always connect those  
wires to the power source running through the fuse box.  
Do not cut out the fuse from the ignition wire (red) and the  
battery wire (yellow). The power supply must be connected  
to the wires via the fuse.  
Insulate unconnected wires with vinyl tape or other similar  
material. To prevent short circuits, also do not remove  
the caps on the ends of the unconnected wires or the  
terminals.  
Connect the speaker wires correctly to the terminals to  
which they correspond. The unit may receive damage or fail  
to work if you share the - wires and/or ground them to  
any metal part in the car.  
After the unit is installed, check whether the brake lamps,  
indicators, wipers, etc. on the car are working properly.  
If the console has a lid, make sure to install the unit so  
that the faceplate does not hit the lid when closing and  
opening.  
Mount the unit so that the mounting angle is 30° or less.  
|
English  
3
Connection  
Monitor/Player unit  
Do not connect.  
USB device  
USB connector (iPod)  
USB connector  
(commercially available)  
USB device  
(commercially available)  
Accessory !  
Wiring harness  
(Accessory 2)  
Ground wire (Black)  
FUSE ( 5A )  
Ground wire (Black)  
The cable (Accessory 3) is  
fixed with a chassis using  
harness band (Accessory  
!).  
Connector A  
BATT  
Battery wire (Yellow)  
Ignition wire (Red)  
8
7
6
5
4
3
2
1
ACC  
8
7
6
5
4
3
2
1
Accessory 0  
(ISO–JASO)  
Accessory 4  
Connector B  
Antenna Cord (ISO)  
FUSE ( 10A )  
(Orange/White)  
Dimmer control wire (Orange/White)  
Connect to the vehicle's parking brake  
detection switch harness  
using the supplied relay connector.  
For the sake of safety, be sure to connect the parking sensor.  
Parking sensor wire (Light Green)  
Reverse sensor wire (Purple/White)  
PRK SW  
To vehicle's reverse lamp harness  
To steering remote  
Steering remote control input (Light Blue/Yellow)  
Mute wire (Brown)  
Connect to the terminal that is grounded when either  
the telephone rings or during conversation.  
To connect the Kenwood navigation system,  
consult your navigation manual.  
Power control/ Motor antenna control wire  
(Blue/White)  
Connect either to the power control terminal when using the optional  
power amplifier, or to the antenna control terminal in the vehicle.  
External amplifier control wire (Pink/Black)  
To "EXT.AMP.CONT." terminal of the amplifier  
having the external amp control function.  
If no connections are made, do not let the cable come out from the tab.  
|
4
KVT-829DVD  
Receiver unit  
Accessory !  
The cable (Accessory 3) is  
fixed with a chassis using  
harness band (Accessory  
!).  
Accessory 3  
Receiver unit  
FM/AM antenna input  
Wiring harness  
(Accessory 1)  
ILLUMI  
Ground wire (Black) - (To car chassis)  
A
REVERSE  
REMO.CONT  
MUTE  
A
+
ANT CONT P. CONT  
EXT. CONT  
Battery  
If you connect the ignition wire (red) and the battery wire (yellow)  
to the car chassis (ground), you may cause a short circuit, that in  
turn may start a fire. Always connect those wires to the power  
source running through the fuse box.  
|
English  
5
Connecting Wires to Terminals  
Connector Function Guide  
Pin Numbers for Cable Colour  
ISO Connectors  
External Power  
Connector  
2WARNING  
Functions  
Connecting the ISO Connector  
The pin arrangement for the ISO connectors depends on  
the type of vehicle you drive. Make sure to make the proper  
connections to prevent damage to the unit.  
A-4  
A-5  
A-6  
A-7  
A-8  
Yellow  
Battery  
Power Control  
Dimmer  
Ignition (ACC)  
Earth (Ground)  
Connection  
The default connection for the wiring harness is described in  
1 below. If the ISO connector pins are set as described in 2  
or 3, make the connection as illustrated.  
Please be sure to reconnect the cable as shown 2 below to  
install this unit to the Volkswagen vehicles etc.  
Blue/White  
Orange/White  
Red  
Black  
Speaker  
Connector  
B-1  
B-2  
B-3  
B-4  
B-5  
B-6  
B-7  
1(Default setting) The A-7 pin (red) of the vehicle’s  
ISO connector is linked with the ignition, and the A-  
4 pin (yellow) is connected to the constant power  
supply.  
Purple  
Purple/Black  
Gray  
Gray/Black  
White  
White/Black  
Green  
Rear Right (+)  
Rear Right (–)  
Front Right (+)  
Front Right (–)  
Front Left (+)  
Front Left (–)  
Rear Left (+)  
Rear Left (–)  
Ignition cable (Red)  
Unit  
Battery cable (Yellow)  
A-7 Pin (Red)  
Vehicle  
A-4 Pin (Yellow)  
B-8  
Green/Black  
2The A-7 pin (red) of the vehicle’s ISO connector is  
connected to the constant power supply, and the  
A-4 pin (yellow) is linked to the ignition.  
A-7 Pin (Red)  
Ignition cable  
Unit  
Vehicle  
A-4 Pin (Yellow)  
Battery cable  
(Yellow)  
3The A-4 pin (yellow) of the vehicle’s ISO connector  
is not connected to anything, while the A-7 pin  
(red) is connected to the constant power supply  
(or both the A-7 (red) and A-4 (yellow) pins are  
connected to the constant power supply).  
Ignition cable (Red)  
Unit  
Battery cable (Yellow)  
A-7 Pin (Red)  
Vehicle  
A-4 Pin (Yellow)  
When the connection is made as in 3 above, the unit’s  
power will not be linked to the ignition key. For that reason,  
always make sure to turn off the unit’s power when the  
ignition is turned off.  
To link the unit’s power to the ignition, connect the ignition  
cable (ACC...red) to a power source that can be turned on  
and off with the ignition key.  
|
6
KVT-829DVD  
System Connection  
To Relay Box  
Accessory @  
Receiver unit  
Front Preout  
• Audio left output (White)  
• Audio right output (Red)  
Rear Preout  
• Audio left output (White)  
• Audio right output (Red)  
Subwoofer Preout  
• Audio left output (White)  
• Audio right output (Red)  
Audio/Visual input 2  
• Visual input (Yellow)  
• Audio left input (White)  
• Audio right input (Red)  
Audio/Visual input 1  
• Visual input (Yellow)  
• Audio left input (White)  
• Audio right input (Red)  
Rear View Camera Input  
• Visual input (Yellow)  
Audio/Visual Output  
• Visual output (Yellow)  
• Audio left output (White)  
• Audio right output (Red)  
|
English  
7
Optional Accessory Connection  
iPod  
(commercially available)  
KCA-iP300V  
(Optional Accessory)  
Audio Input  
Resistance-free stereo type mini  
plug (3.5Ф)  
Audio Output  
(Black)  
Visual Input  
Resistance-free mini plug (3.5Ф)  
Monitor/Player unit  
Visual Output  
(Yellow)  
USB terminal  
USB terminal (iPod)  
USB terminal  
iPod cannot be connected.  
Receiver unit  
Accessory 3  
Connection cable  
(Included in the Disc changer)  
Connection cable  
(Included in the Navigation System)  
Disc Changer etc.  
(Optional Accessory)  
Navigation System  
(Optional Accessory)  
TV Tuner  
(Optional Accessory)  
T V A N T E N N A I N P U T  
R O U N I T  
M O O T N I T  
Connection cable  
(Included in the TV tuner)  
|
8
KVT-829DVD  
Installation for Monitor/Player Unit  
Firewall or metal support  
Screw (M4X8)  
(commercially available)  
Bend the tabs of the mounting  
sleeve with a screwdriver or similar  
utensil and attach it in place.  
Self-tapping screw  
(commercially available)  
Metal mounting strap  
(commercially available)  
Accessory 5  
Make sure that the unit is installed securely in place. If the unit is unstable,  
it may malfunction (eg, the sound may skip).  
Installation for Receiver Unit  
1. Attach the installation brackets 9 to the sides of  
the receiver unit using the sems bolts 7.  
Installation brackets  
(Accessory 9)  
Sems bolts (M4 × 8 mm)  
(Accessory 7)  
2. Use the tapping screw 8 to secure the receiver  
unit to the audio board.  
Tapping screw (ø4 × 16 mm)  
(Accessory 8)  
|
English  
9
Removing Monitor/Player Unit  
Removing the Hard Rubber Frame  
(escutcheon)  
1. Engage the catch pins on the removal tool 6 and  
remove the two locks on the lower level.  
Lower the frame and pull it forward as shown in  
the figure.  
Removing the Unit  
1. Remove the hard rubber frame by referring to the  
removal procedure in the section <Removing the  
Hard Rubber Frame>.  
2. Remove the Hex-head screw with integral washer  
(M4 × 8) on the back panel.  
3. Insert the two removal tools 6 deeply into the  
slots on each side, as shown.  
Removal Tool (Accessory 6)  
Removal Tool  
(Accessory 6)  
Catch  
Lock  
The frame can be removed from the top side in the same  
manner.  
4. Lower the removal tool toward the bottom, and  
pull out the unit halfway while pressing towards  
the inside.  
2. When the lower level is removed, remove the  
upper two locations.  
Be careful to avoid injury from the catch pins on the  
removal tool.  
5. Pull the unit all the way out with your hands, being  
careful not to drop it.  
|
10  
KVT-829DVD  

Roadmaster 3 way Speakers RS630 User Manual
Ricoh CX1 User Manual
Raypak 0090B 0135B User Manual
Pioneer XM SATELLITE DIGITAL TUNER GEX P910XM User Manual
Panasonic AJ SPD850P User Manual
Orion Car Audio CO8001 User Manual
Olevia ZP 500 User Manual
Nokia HS 11W User Manual
KitchenAid KEBS146W User Manual
JVC High Definition Camcorder GZ HM30 User Manual