Kenwood CD RECEIVER KDC 5070R User Manual

CD-RECEIVER  
KDC-6070R  
KDC-5070R  
INSTRUCTION MANUAL  
COMPACT  
DIGITAL AUDIO  
© B64-1296-00 (EW)  
Safety precautions  
IMPORTANT INFORMATION  
2WARNING  
2CAUTION  
You cannot connect the unit directly to the  
following CD automatic changers. For users  
who want to use older changers with the  
unit, follow the directions below according to  
the type of changer you own:  
To prevent injury and/or fire, take the  
following precautions:  
• Insert the unit all the way until it is fully  
locked in place. Otherwise it may fly out of  
place during collisions and other jolts.  
To prevent damage to the machine,  
take the following precautions:  
• Make sure to ground the unit to a negative  
12V DC power supply.  
• KDC-C200 / KDC-C300 / KDC-C400  
• Do not open the top or bottom covers of the  
unit.  
• Do not install the unit in a spot exposed to  
direct sunlight or excessive heat or humidity.  
Also avoid places with too much dust or the  
possibility of water splashing.  
• Do not set the removed faceplate or the  
faceplate case in areas exposed to direct  
sunlight, excessive heat or humidity. Also  
avoid places with too much dust or the  
possibility of water splashing.  
• To prevent deterioration, do not touch the  
terminals of the unit or faceplate with your  
fingers.  
• Do not subject the faceplate to excessive  
shock, as it is a piece of precision equipment.  
• When replacing a fuse, only use a new one  
with the prescribed rating. Using a fuse with  
the wrong rating may cause your unit to  
malfunction.  
• To prevent short circuits when replacing a  
fuse, first disconnect the wiring harness.  
• Do not place any object between the  
faceplate and the unit.  
Use the extension cable and the control box  
attached to the CD changer, and the optional  
CA-DS100 converter cable.  
• KDC-C301 / KDC-C600 / KDC-C800 / KDC-  
C601 / KDC-C401  
Use the extension cable attached to the CD  
changer, and the optional CA-DS100  
converter cable.  
• KDC-C100 / KDC-C302 / C205 / C705 /  
non-Kenwood CD changers  
• When extending the ignition, battery or  
ground cables, make sure to use automotive-  
grade cables or other cables with an area of  
2
0.75mm (AWG18) or more to prevent cable  
deterioration and damage to the cable  
coating.  
• To prevent short circuits, never put or leave  
any metallic objects (e.g., coins or metal  
tools) inside the unit.  
• If the unit starts to emit smoke or strange  
smells, turn off the power immediately and  
consult your Kenwood dealer.  
• Make sure not to get your fingers caught  
between the faceplate and the unit.  
• Be careful not to drop the unit or subject it to  
strong shock.  
The unit may break or crack because it  
contains glass parts.  
• Do not touch the liquid crystal fluid if the LCD  
is damaged or broken due to shock. The  
liquid crystal fluid may be dangerous to your  
health or even fatal.  
If the liquid crystal fluid from the LCD  
contacts your body or clothing, wash it off  
with soap immediately.  
Cannot be used with this model.  
2CAUTION  
You can damage both your unit and  
the CD changer if you connect them  
incorrectly.  
2CAUTION  
Do Not Load 8-cm (3-in.) CDs in the  
CD slot  
If you try to load an 8-cm CD with its adapter  
into the unit, the adapter might separate from  
the CD and damage the unit.  
• During installation, do not use any screws  
except for the ones provided. The use of  
improper screws might result in damage to  
the main unit.  
— 3 —  
Safety precautions  
Cleaning the Unit  
Cleaning the CD Slot  
NOTE  
If the front panel gets dirty, turn off the  
power and wipe the panel with a dry silicon  
cloth or soft cloth.  
As dust can accumulate in the CD slot, clean  
it occasionally. Your CDs can get scratched if  
you put them in a dusty CD slot.  
• If you experience problems during  
installation, consult your Kenwood dealer.  
Egnlish  
• If the unit does not seem to be working right,  
try pressing the reset button first. If that does  
not solve the problem, consult your Kenwood  
dealer.  
2CAUTION  
Do not wipe the panel with a stiff cloth or a  
cloth dampened by volatile solvents such as  
paint thinner and alcohol. They can scratch  
the surface of the panel and/or cause the  
indicator letters to peel off.  
POWER  
OFF  
SRC  
CLK  
FM  
DISC  
PTY  
T
E
X
T
NAME.S  
TI VOL ADJ DISP  
DISC  
ATT  
LOUD  
SCAN  
RDM  
REP  
D.SCN  
M.RDM  
AM  
MENU  
1
2
3
4
5
6
AUD  
The marking of products using lasers  
(Except for some areas)  
Reset button  
Lens Fogging  
CLASS 1  
LASER PRODUCT  
Right after you turn on the car heater in cold  
weather, dew or condensation may form on  
the lens in the CD player of the unit. Called  
lens fogging, CDs may be impossible to play.  
In such a situation, remove the disc and wait  
for the condensation to evaporate. If the unit  
still does not operate normally after a whilst,  
consult your Kenwood dealer.  
• Characters in the LCD may become difficult  
to read in temperatures below 41 ˚F (5 ˚C).  
The label is attached to the chassis/case and  
says that the component uses laser beams  
that have been classified as Class 1. It means  
that the unit is utilizing laser beams that are  
of a weaker class. There is no danger of  
hazardous radiation outside the unit.  
Cleaning the Faceplate Terminals  
If the terminals on the unit or faceplate get  
dirty, wipe them with a dry, soft cloth.  
— 4 —  
Handling Compact discs  
Playing a CD that is dirty, scratched  
or warped can cause the sound to  
skip and the unit to operate  
incorrectly, resulting in worsened  
sound quality. Take the following  
precautions to prevent your CDs from  
getting scratched or damaged.  
Cleaning CDs  
Do Not Load CD Accessories in Slot  
If a CD has become dirty, wipe it off gently  
using a commercially available cleaning cloth  
or a soft cotton cloth, starting from the  
centre of the disc and moving outward. Do  
not clean CDs with conventional record  
cleaners, anti- static formulas, or chemicals  
such as paint thinner or benzene.  
Do not use commercially available CD  
accessories that can be loaded into the CD  
slot, such as stabilisers, protective sheets, or  
CD cleaning discs, since they can cause the  
unit to malfunction.  
Removing the CD  
Only remove the CD from the machine in a  
horizontal direction. You may damage the  
surface of the CD if you try pulling it down as  
it ejects.  
Handling CDs  
• Do not touch the recorded side of the CD  
(i.e., the side opposite the label) when  
holding it.  
Checking New CDs for Burrs  
When playing a new CD for the first time,  
check that there are not any burrs stuck to  
the perimeter of the disc or in the central  
hole. CDs with burrs stuck on them may not  
load properly or may skip whilst playing.  
Remove burrs using a ballpoint pen or a  
similar utensil.  
Do Not Use Special Shape CDs  
• Be sure to use round shape CDs only for this  
unit and do not use any special shape CDs.  
Use of special shape CDs may cause the  
unit to malfunction.  
• Do not stick tape on either side of the CD.  
Tape  
Burrs  
Storing CDs  
COMPACT  
• Do not store CDs in areas exposed to direct  
sunlight – such as a car seat or above the  
fascia panel (dashboard) – or other hot  
places.  
• Remove CDs from the unit when not  
listening to them for a whilst, and put them  
back in their cases. Do not stack CDs that  
have been removed from their cases or prop  
them against something.  
DIGITAL AUDIO  
• Be sure to use CDs with disc mark  
Burrs  
only for this unit.  
Do Not Use CDs with Sticker on the  
Labeled Side  
Do not use the CD with the label sticker  
stuck on it.  
Using such a CD may cause the CD to be  
deformed and the sticker to peel off,  
resulting in malfunction of the unit.  
— 5 —  
Basic operations  
SRC /  
PWR OFF  
Power  
4
¢
u
d
FM  
Turning on the power:  
POWER  
OFF  
SRC  
Press the SRC button.  
CLK  
Egnlish  
FM  
AM  
DISC  
NOTE  
PTY  
Turn the power on before carrying out the following procedures.  
T
E
X
T
NAME.S  
TI VOL ADJ  
DISP  
DISC  
ATT  
LOUD  
SCAN  
RDM  
REP  
D.SCN  
M.RDM  
MENU  
Turning off the power:  
1
2
3
4
5
6
AUD  
Hold down the PWR OFF button for one second or more.  
MENU  
AM  
ATT / LOUD  
for KDC-6070R  
Switching Modes  
Switching Modes:  
Each time you press the SRC button, the mode switches as  
follows:  
LOUD indicator  
LOUD  
ATT  
Tuner mode  
CD mode  
I
External disc control mode  
ATT indicator  
AUX mode (KDC-6070R only)  
NOTE  
for KDC-5070R  
• The mode switches to the next mode from any mode which  
cannot be used.  
• The external disc control mode will differ depending on the unit  
that is connected.  
LOUD indicator  
• The AUX mode is available only when the changer / AUX  
switching adapter (KCA-S210A or CA-C1AX) or CD changer  
(KDC-CPS82 or KDC-CX82) is connected to this unit.  
During the AUX mode, "AUX" will show in the display.  
When the CA-C1AX is being used, the AUX Mode will replace  
the External Disc Control Mode.  
I
LOUD  
ATT  
ATT indicator  
— 6 —  
Volume  
Increasing Volume:  
Press the u button to turn up the volume.  
Decreasing Volume:  
Press the d button to turn down the volume.  
Attenuator  
This function allows you to turn down the volume quickly.  
Turning Attenuator On/Off:  
Press the ATT button to switch the attenuator on and off.  
When the attenuator is on, the ATT indicator blinks.  
When the attenuator is off, the volume returns to the original  
level.  
NOTE  
Turning down the volume all the way turns off the attenuator  
function.  
— 7 —  
Basic operations  
ON / OFF) Disabled System Indicator (DSI ON / OFF) ➞  
Selectable Illumination (COL GRN / AMB) Contrast  
Adjustment (CONT ##) Dimmer (DIM ON / OFF) ➞  
Switching Graphic Display(GRAP ON / OFF) News Bulletin  
Menu System  
To accommodate a greater number of functions, a menu  
system has been employed for making settings. Press the  
MENU button to enter the menu mode and then display the  
function to make the setting. Details on each setting are  
explained separately in the corresponding function page.  
4
Egnlish  
Function (NEWS OFF / ##M) Local seek* (LO.S OFF / ON)  
4
Selecting Tuning Mode* (Auto 1 / Auto 2 / Manual) Auto  
4
5
Memory Entry* (A-Memory (start)) AF Function* (AF ON /  
5
OFF) Region Restrict Function* (REG ON / OFF) Auto  
1
Hold down the MENU button for one second or more.  
"MENU" is displayed when the menu mode is entered.  
The function that you can adjust is indicated with the current  
settings displayed.  
4
5
TP Seek* (ATPS ON / OFF) Monaural Reception* (MONO  
3
OFF / ON) Text Scroll* (SCL Manu / Auto) Touch Sensor  
Tone  
• KDC-5070R  
2
Selecting function to set  
Switching Clock Display (CLK ON / OFF) Time  
1
2
Press the ¢ button to search through the functions until you  
see the one you want to adjust in the display.  
Press the 4 button to search through the functions  
backward.  
Adjustment* <Manual> (CLK ADJ* ) Automatic Time  
Adjustment (SYNC ON / OFF) Disabled System Indicator  
(DSI ON / OFF) Selectable Illumination (COL GRN / AMB) ➞  
Touch Sensor Tone (BEEP ON / OFF) News Bulletin  
4
Example: If you want to switch the tuning mode from auto1 to  
manual, first search through the functions until you  
see "Auto 1" in the display.  
Function (NEWS OFF / ##M) Local seek* (LO.S OFF / ON)  
4
Selecting Tuning Mode* (AUTO1 / AUTO2 / MANUAL) ➞  
4
5
Auto Memory Entry* (A-MEMORY (start)) AF Function*  
5
(AF ON / OFF) Region Restrict Function* (REG ON / OFF)  
5
5
Auto TP Seek* (ATPS ON / OFF) Monaural Reception*  
3
(MONO OFF / ON) Text Scroll* (SCL MANU / AUTO) ➞  
Switching Clock Display  
KDC-6070R  
KDC-5070R  
1
* When Automatic Time Adjustment is off  
2
* Time adjustment mode entered  
3
4
Changing setting for currently displayed function  
Press either the AM or FM button.  
The setting will change for each function.  
Example: The tuning mode will switch from auto 1 to auto 2.  
Pressing the button again switches the setting to  
manual, and "Manual" is displayed.  
3
* In FM, CD, or External disc control mode  
4
*
*
In Tuner mode  
5
In FM reception of Tuner mode  
NOTE  
• Make sure to end the menu mode when finished.  
If you fail to end the menu mode, several functions may not  
operate properly, including the Traffic Information function, the  
News Bulletin function with PTY news timeout setting, and the  
Alarm function.  
• The News function turns on when the setting is made for the  
news interruption interval. The "##M" display indicates the  
setting selected for the news interruption timeout interval.  
• The "##" display indicates the setting value.  
Auto 2  
Manual  
Ending the menu mode  
Press the MENU button.  
The selection includes:  
• KDC-6070R  
Touch Sensor Tone (Beep ON / OFF) Time Adjustment*  
<Manual> (CLK ADJ* ) Automatic Time Adjustment (SYNC  
1
2
— 8 —  
Tuner features  
Loudness  
4
SRC  
FM  
¢
This function amplifies low and high tones when the volume is  
POWER  
OFF  
turned down.  
SRC  
CLK  
The LOUD indicator lights up, when the loudness function is  
on.  
FM  
AM  
DISC  
PTY  
T
E
X
T
NAME.S  
TI VOL ADJ  
DISP  
DISC  
Turning Loudness On/Off:  
ATT  
LOUD  
SCAN  
RDM  
REP  
D.SCN  
M.RDM  
MENU  
Hold down the LOUD button for one second or more to switch  
the loudness on and off.  
1
2
3
4
5
6
AUD  
AM  
#1~6  
DISP  
MENU  
for KDC-6070R  
STEREO indicator  
Mode display  
Frequency  
STEREO  
AUTO  
1
2
III  
Band display  
AUTO indicator  
Preset station number  
for KDC-5070R  
Band display  
Frequency  
III  
1
ST  
AUTO  
2
Preset station number  
ST indicator  
AUTO indicator  
— 9 —  
Tuner features  
NOTE  
Selecting Tuning Mode  
If the frequencies stored at the preset numbers receive  
stations which were not originally memorized when traveling  
long distances, the preset number is not displayed. In such  
cases, pressing the 4/¢ button to use preset station seek  
will receive channel 1.  
You can choose from three tuning modes: auto seek, preset  
station seek, and manual. The “AUTO 1” indicator lights up  
when auto seek tuning is selected, and the “AUTO 2” indicator  
lights when preset station seek tuning is selected.  
Egnlish  
1
Hold down the MENU button for one second or more.  
"MENU" is displayed and the menu mode is turned on.  
• Manual Tuning  
Press the ¢ button to increase the frequency by one step.  
Press the 4 button to decrease the frequency by one step.  
2
Press the ¢ button repeatedly until the tuning function  
appears in the display.  
NOTE  
Press the 4 button to search in the other direction.  
The tuning method is displayed as ”Auto 1“, ”Auto 2“, or  
”Manual“ referring respectively to auto seek tuning, preset  
station seek tuning, and manual tuning.  
The ST/STEREO indicator lights up when stereo broadcasts are  
being received.  
3
4
Switching settings  
Press either the AM button or FM button to switch the tuning  
mode.  
Local Seek Function  
With the local seek function turned on, auto seek tuning skips  
stations with relatively poor reception.  
The display and setting will change.  
Press the MENU button to end the menu mode.  
Turning Local Seek Function On/Off:  
1
Hold down the MENU button for one second or more.  
"MENU" is displayed and the menu mode is turned on.  
Tuning  
1
2
Press the SRC button repeatedly until the tuner mode is  
Press the ¢ button repeatedly until the local seek function  
appears in the display.  
Press the 4 button to search in the other direction.  
The function setting is indicated by "LO.S ON" or "LO.S OFF" in  
the display, indicating that the local seek function is on or off,  
respectively.  
obtained. "TUNER" is displayed only when the tuner mode is  
selected.  
2
Press either the FM or AM button to select the band.  
Each time you press the FM button, the band switches  
between the FM1, FM2 and FM3.  
3
4
Press the AM button to select the MW and LW bands.  
Switching settings  
Press either the AM button or FM button.  
The display and setting will change.  
3
• Auto Seek Tuning  
Press the ¢ button to seek increasing frequencies.  
Press the 4 button to seek decreasing frequencies.  
• Preset station seek tuning  
Press the MENU button to end the menu mode.  
Press the ¢ button to move to the next preset station (i.e.,  
the one with the next highest number), and the 4 button to  
move to the last preset station (i.e., the one with the next  
lowest number).  
— 10 —  
Recalling a Preset Station:  
Station Preset Memory  
Store the frequency of the station currently being listened to.  
You can then recall that station with a single touch of a button.  
Press the preset station button (#1-6) for the desired station.  
The number of the recalled station is displayed.  
NOTE  
1
2
Select the band/ station that you want to have stored.  
• When the AF function is turned on whilst auto memory entry  
takes place, only RDS stations (i.e., stations with RDS capability)  
are stored. RDS stations that have been preset for FM1 cannot  
also be preset in FM2 or FM3.  
• When the local seek function is turned whilst auto memory  
entry takes place, stations with poor reception are not stored.  
• When the Traffic Information function is on , only the local traffic  
information station frequency will be stored.  
Hold down the button (#1-6) that you want to use for the  
station, for two seconds or more.  
The button number blinks once in the display to indicate that  
the data has been stored.  
Recalling a Preset Station:  
Press the preset station button (#1-6) for the desired station.  
The number of the recalled station is displayed.  
Cancelling Auto Memory Entry During Its Operation:  
Press the MENU button whilst auto memory entry is taking  
place to stop the process.  
NOTE  
You can store 6 stations in each of the FM1, FM2, FM3, and AM  
(MW and LW) bands.  
Auto Memory Entry  
You can automatically store all the receivable frequencies in  
the band currently being listened to, and then recall them with  
the touch of a button later. This function is especially useful  
when you are travelling and do not know what stations are  
available. Up to 6 frequencies can be stored this way.  
1
2
Select the band for auto memory entry.  
Hold down the MENU button for one second or more.  
"MENU" is displayed and the menu mode is turned on.  
3
4
Press the ¢ button repeatedly until "A-Memory" appears in  
the display.  
Press the 4 button to search in the other direction.  
Hold down either the AM button or FM button for two seconds  
or more to start auto memory function.  
The numbers of the preset station buttons showed in order.  
When all the stations in a certain band are stored in the preset  
memory, the auto memory entry stops. The tuner then plays  
the last station received.  
— 11 —  
Tuner features  
2
Press the ¢ button repeatedly until the monaural reception  
function appears in the display.  
Press the 4 button to search in the other direction.  
The function setting is indicated by "MONO OFF" or "MONO  
ON" in the display, indicating that monaural reception is on or  
off, respectively.  
Station Name Preset Play (SNPP)  
(Function of Remote)  
You can search for the preset station with Programme Service  
name.  
Egnlish  
1
Press the DNPP button on the remote control.  
“SNP PLAY/SNPP” will be displayed once the seek mode is  
entered.  
3
4
Switching settings  
Press either the AM button or FM button.  
The display and setting will change.  
The names of the stations preset in the band currently listened  
to are displayed for 5 seconds each.  
Press the MENU button to end the menu mode.  
The display band switches in the following order:  
= FM1 Ô FM2 Ô FM3 Ô AM +  
Each time you press the ¢ button, the station display  
switches in the forward direction.  
Each time you press the 4 button, the station display  
Function of the KDC-5070R  
switches in the reverse direction.  
Stations which have no names will be displayed as frequencies.  
Switching Display for Tuner  
Switching the Display:  
NOTE  
Changing the Displayed Band  
Each time you press the DISP button, the display switches  
between the Programme service name (during RDS station  
reception)/frequency and clock.  
Pressing the FM button switches between the FM1, FM2, FM3  
and AM displays, in that order.  
Pressing the AM button switches between the displays in the  
reverse direction.  
NOTE  
The £ indicator lights whilst the clock is displayed.  
2
Once the name is displayed for the station you want to listen  
to  
Press the OK button.  
Reception starts of the displayed station, and the seek mode  
ends.  
Cancelling mode during input:  
Press the DNPP button.  
The seek mode is cancelled.  
Monaural Reception  
When poor stereo reception is experienced, this function will  
reduce noise and improve listening conditions.  
1
Hold down the MENU button for one second or more.  
"MENU" is displayed and the menu mode is turned on.  
— 12 —  
RDS features  
38/PTY  
4
FM  
¢
RDS (Radio Data System)  
RDS is a digital information system that lets you receive signals  
besides those of regular radio programmes, such as network  
information being transmitted from radio stations.  
When listening to an RDS station (ie, a station with RDS  
capability), the programme service name of the station is  
displayed along with the frequency, advising you quickly which  
station is being received.  
POWER  
OFF  
SRC  
CLK  
FM  
AM  
DISC  
PTY  
T
E
X
T
NAME.S  
TI VOL ADJ DISP  
DISC  
ATT  
LOUD  
SCAN  
RDM  
REP  
D.SCN  
M.RDM  
MENU  
1
2
3
4
5
6
AUD  
RDS (Radio Data System) stations also transmit frequency data  
for the same station. When you are making long trips, this  
function automatically switches to the particular frequency with  
the best reception for the particular network of stations that  
you want to listen to. The data is automatically stored,  
allowing you to switch quickly to another RDS stations,  
broadcasting the same programme, that has better reception.  
These include stations stored in the station preset memory that  
you often listen to.  
#1~6  
MENU  
AM  
TI /  
VOL ADJ  
for KDC-6070R  
NEWS indicator  
NEWS  
TEXT  
EON (Enhanced Other Network)  
TI  
III  
Stations that offer EON also transmit information about other  
RDS stations that have traffic information. When you are tuned  
to a station that is not transmitting traffic information, but  
another RDS station starts transmitting a traffic bulletin, the  
tuner automatically switches to the other station for the  
duration of the bulletin.  
Band display  
TI indicator  
indicator  
for KDC-5070R  
NEWS indicator  
Band display  
Alarm  
When an emergency transmission (announcing disasters, etc.)  
is sent, all current functions are interrupted to allow the  
warning to be received.  
III  
TI  
NEWS  
PTY  
TI indicator  
indicator  
— 13 —  
RDS features  
Turning Region Restrict Function On/Off:  
AF (Alternative Frequency) Function  
1
Hold down the MENU button for one second or more.  
"MENU" is displayed and the menu mode is turned on.  
When poor reception is experienced, automatically switch to  
another frequency broadcasting the same programme in the  
same RDS network with better reception.  
The indicator lights up when the AF function is turned  
on.  
2
Press the ¢ button repeatedly until the Region restrict  
function appears in the display.  
Egnlish  
Press the 4 button to search in the other direction.  
The function setting is indicated by "REG ON" or "REG OFF" in  
the display, indicating that the function is on or off,  
respectively.  
Turning AF Function On/Off:  
1
Hold down the MENU button for one second or more.  
"MENU" is displayed and the menu mode is turned on.  
3
4
Switching settings  
2
Press the ¢ button repeatedly until the AF function appears  
in the display.  
Press either the AM button or FM button.  
The display and setting will change.  
Press the 4 button to search in the other direction.  
The function setting is indicated by "AF ON" or "AF OFF" in the  
display, indicating that the AF function is on or off, respectively.  
Press the MENU button to end the menu mode.  
NOTE  
3
4
Sometimes stations in the same network broadcast different  
programmes or use different programme service names.  
Switching settings  
Press either the AM button or FM button.  
The display and setting will change.  
Press the MENU button to end the menu mode.  
Displaying Frequencies:  
Traffic Information Function  
You can listen to traffic information. If you are listening to  
tapes or discs, they will continue playing until a traffic bulletin  
is broadcast.  
Hold down the DISP button for one second or more.  
The frequency for the RDS station will be displayed for five  
seconds instead of the station name.  
NOTE  
When no other stations with stronger reception are available for  
the same programme in the RDS network, you may hear the  
incoming broadcast in bits and snatches. Turn off the AF function  
in such a case.  
Turning TI function On/Off:  
Press the TI button to turn the function on and off.  
When the function is on, the TI indicator is turned on.  
When none is being received, the TI indicator will blink on and  
off. When a traffic information station is being received, the TI  
indicator will turn on.  
When a traffic bulletin begins to be broadcast, "TRAFFIC" will  
be displayed, and reception will begin at the preset volume.  
If you are listening to a tape or disc when a traffic bulletin  
begins, they will automatically be turned off. When the bulletin  
ends or poor reception is experienced, the tape or disc will  
begin playing again.  
Restricting RDS Region (Region Restrict Function)  
You can choose whether or not to restrict the RDS channels,  
received with the AF function for a particular network, to a  
specific region. When the Region Restrict Function is on, the  
region is restricted.  
— 14 —  
NOTE  
3
4
Switching settings  
Pressing the TI button whilst in the MW/LW band automatically  
switches reception to the FM band. However, the MW/LW band  
is not returned to when the TI button is pressed again.  
Press either the AM button or FM button.  
The display and setting will change.  
If the traffic information station you are tuned to experiences  
poor reception, this function automatically seeks another TP  
station.  
Switching to a Different Traffic Information Station:  
Use the 4 / ¢ buttons to make an auto seek of the TI  
stations in a certain band.  
Press the MENU button to end the menu mode.  
NOTE  
• When you are listening to a tape or disc, you cannot change to  
another TI station.  
• When the auto TP seek function is turned on and reception  
starts to weaken, the tuner automatically seeks traffic  
information stations with better reception.  
• If you are tuned to a station that is not a traffic information  
station itself but which provides EON services, you can still have  
traffic information received.  
• Holding the TI button down for one second or more when the TI  
function is on in the disc control mode results in a change to the  
frequency display of the traffic information station for five  
seconds.  
Presetting Volume for Traffic Information/News  
Preset the volume level to be used for traffic information and  
news broadcasts.  
1
2
3
Tune into the station for which you want to set the volume.  
Adjust the volume to the desired level.  
Hold down the TI VOL ADJ button for two seconds or more.  
The volume level blinks once in the display to indicate that the  
data has been stored.  
Future traffic information/news broadcasts are heard at the  
preset level.  
NOTE  
Auto TP Seek Function  
• The volume cannot be lowered by this function during tuner  
reception. The volume is only set when it is louder than the  
listening volume of the tuner.  
• You can arrange only to listen to traffic information or news  
bulletins with at preset volume with the volume set at  
minimum.  
When the TI function is on and poor reception conditions are  
experienced when listening to a traffic information station,  
another traffic information station with better reception will be  
searched for automatically. This function is on, when unit is  
first powered on.  
Turning Auto TP Seek Function On/Off:  
1
Hold down the MENU button for one second or more.  
"MENU" is displayed and the menu mode is turned on.  
2
Press the ¢ button repeatedly until the Auto TP Seek  
function appears in the display.  
Press the 4 button to search in the other direction.  
The function setting is indicated by "ATPS ON" or "ATPS OFF" in  
the display, indicating that the function is on or off,  
respectively.  
— 15 —  
RDS features  
NOTE  
News Bulletin Function  
with PTY News Timeout Setting  
If you choose the "20M" setting, further news bulletins will not be  
received for 20 minutes once the first news bulletin is received.  
Setting the interval at the "00M" factory default indicates no News  
Timeout will be made, meaning that additional news bulletins will  
continue to be searched for.  
You can arrange to have news bulletins interrupt your current  
listening source, including other radio stations. When the News  
Bulletin function is on, the PTY News Timeout setting allows  
you to set the interval during which further news interruption  
cannot take place. You can adjust the PTY news interruption  
period from 10 to 90 minutes for each journey.  
Egnlish  
4
Press the MENU button to end the menu mode.  
NOTE  
Turning News Bulletin Function On/Off:  
• This function is only available if the desired station sends PTY-  
code for news bulletin or belongs to EON-Network sending PTY-  
code for news bulletin.  
1
Hold down the MENU button for one second or more.  
"MENU" is displayed and the menu mode is turned on.  
• If you turn on the news bulletin function in the MW/LW band,  
the band is switched automatically to the FM band.  
However, the MW/LW band is not returned to when you turn off  
the function.  
2
Press the ¢ button repeatedly until the News Bulletin  
function appears in the display.  
Press the 4 button to search in the other direction.  
The function setting is indicated by "NEWS OFF" or "NEWS  
##M" in the display, indicating that the function is on or off,  
respectively.  
NOTE  
Programme Type (PTY) Function  
Conduct auto seek tuning only on those stations with selected  
kinds of programmes.  
Depending on the interval chosen, the "##M" in the display will  
change when the function is turned on.  
3
Changing the Function Setting  
Press either the FM or AM button.  
1
Press the 38(PTY) button.  
Each time you press the FM or AM button until the desired  
setting is displayed.  
“PTY” is displayed, and the Programme Type Selection (PTY)  
Mode entered.  
Press the FM button to increase the interval, and the AM  
button to decrease it.  
If you make no key input in 30 seconds, the mode will  
automatically turn off.  
OFF 00M 10M 20M 30M 40M 50M 60M  
NOTE  
70M 80M 90M  
(M= minutes)  
You cannot use this function whilst the traffic information  
function is turned on.  
When you select the news interruption timeout interval, the  
News function turns on and the NEWS indicator lights up.  
When a news bulletin is received, "NEWS" will be displayed and  
reception will begin at the preset volume.  
NOTE  
Changing the Display Language to French, German, or Swedish  
In the PTY mode, hold down the 38(PTY) button for one second  
or more to display the name of the language currently used.  
If you want to change the language, press the preset button for  
the desired language and then the 38(PTY) button.  
English is #1, French is #2, German is #3, and Swedish is #4  
(KDC-6070R only).  
— 16 —  
NOTE  
2
Select the type of programme to be received  
• Press either the FM or AM buttons repeatedly until the type  
of programme you want to listen to.  
If no programme can be found, "NO PTY" is displayed.  
If you want to select another type of programme, repeat steps 2  
and 3 above.  
The selection includes:  
Speech(SPEECH) 1.News(NEWS) 2.Current  
Affairs(AFFAIRS) 3.Information(INFO) 4.Sports(SPORT)  
5.Education(EDUCATE) 6.Drama(DRAMA) ↔  
7.Culture(CULTURE) 8.Science(SCIENCE) ↔  
9.Varied(VARIED) 10.Pop Music(POP M) 11.Rock  
Music(ROCK M) 12.Easy Listening Music(EASY M) ↔  
13.Light Classical(LIGHT M) 14.Serious  
Classical(CLASSICS) 15.Other Music(OTHER M) ↔  
16.Weather(WEATHER) 17.Finance(FINANCE) ↔  
18.Children’s programmes(CHILDREN) 19.Social  
Affairs(SOCIAL A) 20.Religion(RELIGION) 21.Phone  
In(PHONE IN) 22.Travel(TRAVEL) 23.Leisure(LEISURE)  
24.Jazz Music(JAZZ) 25.Country Music(COUNTRY) ↔  
26.National Music(NATION M) 27.Oldies Music(OLDIES)  
28.Folk Music(FOLK M) 29.Documentary(DOCUMENT)  
Music(MUSIC) Speech(SPEECH)↔  
Switching to Other Stations with the Same Type of Programme:  
When “PTY” is blinking in the display, perform auto seek  
tuning.  
The tuner scans for another station with the same type of  
programme.  
Cancelling Programme Type Function During Its Operation:  
Press the 38(PTY) button.  
(Speech.....1~9,16~23, 29, Music.....10~15, 24~28)  
• You can select the type of programme directly by pressing a  
preset button. The buttons are factory-set to the following  
type of programmes:  
1. Music  
4. Other Music  
2. Speech  
5. Serious Classical  
3. News  
6. Varied  
NOTE  
Changing the Preset Button Settings for Programme Type  
After selecting the type of programme to be stored in a certain  
preset button, hold down that button for two seconds or more.  
The previously stored data for that button are erased and the new  
programme type is stored.  
3
Seeking the selected programme type  
Press the 4 or ¢ button to make a seek of frequencies  
with your selected type of programme.  
The display blinks and the seek starts.  
If your selected type of programme is found, the name of the  
station is displayed and the station is tuned into.  
“PTY” blinks in the display for about 30 seconds.  
If you make no key input in 30 seconds, the PTY selection  
mode will turn off automatically.  
— 17 —  
RDS features  
Function of the KDC-6070R  
Function of the KDC-6070R  
Text Scroll  
Radio Text  
This function permits the text to be scrolled and the entire text  
to be displayed. Switching between manual scrolling and  
automatic scrolling is permitted. The factory default is manual  
scrolling.  
You can display textual information being transmitted by RDS  
stations.  
Egnlish  
Turning on Radio Text Display Mode:  
Pressing the DISP button switches the display as follows.  
Select the Radio Text Display mode.  
To scroll manually:  
1
2
Press the DISP button to display the Radio Text.  
Pressing the DISP button for at least one second results in one  
scrolling display of the text.  
Program Service name  
Radio text  
Manual/Automatic scroll switching:  
1
Press the MENU button for at least one second.  
"MENU" is displayed and the menu mode is turned on.  
NOTE  
If the RDS station currently tuned to is transmitting no text while  
the Radio Text Display mode is turned on, "NO TEXT" will appear  
in the display. While awaiting reception, "WAITING" will be  
displayed.  
2
Keep pressing the ¢ button until the Text scroll function  
appears in the display.  
Pressing the 4 button results in the functions being switched  
in the reverse order.  
2WARNING  
The text scroll function is displayed with "SCL Auto" or "SCL  
Manu".  
To prevent accidents, drivers should not look at the display while  
on the road.  
"SCL Manu" (Manual scrolling)  
"SCL Auto" (Automatic scrolling)  
3
4
Switching settings  
Press either the AM or FM button.  
The display and setting will change.  
Press the MENU button to end the menu mode.  
To scroll automatically:  
1
Press the DISP button to display the Radio Text.  
The text will be displayed in one scrolling display.  
2
Pressing the DISP button for at least one second results in one  
scrolling display of the text.  
NOTE  
The setting of the text scroll function is in common with Text  
Scroll for disc control.  
— 18 —  
CD/External disc control features  
Release button  
When a unit equipped with an O-N switch is to be connected,  
please also see the instruction manual of this unit.  
Set the O-N switch to "N". "N"-operation will be set.  
When a unit that is not equipped with an O-N switch, or the  
changer switching unit "KCA-S200" is connected, "O"-  
operation will be set.  
4
FM/  
DISC+  
38  
SRC  
¢
POWER  
OFF  
SRC  
CLK  
FM  
AM  
DISC  
PTY  
T
E
X
T
"N"-operation:  
NAME.S  
TI VOL ADJ DISP  
DISC  
ATT  
LOUD  
SCAN  
RDM  
REP  
D.SCN  
M.RDM  
• The disc title and track title of the CD text can be displayed.  
• The disc name will be displayed when the name has been  
registered to any connected unit with the Presetting Disc  
Names function, or when the playing unit contains a disc to  
which the disc title has been recorded.  
MENU  
1
2
3
4
5
6
AUD  
REP  
M.RDM  
SCAN  
MENU  
DISP/  
NAME.S  
AM/  
DISC-  
RDM  
D.SCN  
"O"-operation:  
• CD text cannot be displayed.  
for KDC-6070R  
• Regardless of the control unit, the characters that can be  
registered with the Presetting Disc Names function are "A~Z  
0~9 /, +, –, , =, <, >, [ , ]".  
Mode display  
Track time  
• The disc name will be displayed when the name has been  
registered to the playing unit with the Presetting Disc Names  
function.  
TEXT  
NOTE  
III  
The CD text, Presetting Disc Names, and Disc Name Preset Play  
functions may not be operational depending on the unit.  
Disc indicator  
Track number  
Disc number  
for KDC-5070R  
Track number  
Track time  
III  
CHANGER  
AUTO  
1
2
Disc indicator  
Disc number  
— 19 —  
CD/External disc control features  
• The unit can only play 12-cm (5-inch) CDs. If you insert an 8-cm  
(3-inch) CD, it will get stuck inside and can cause the unit to  
malfunction.  
• When the faceplate has been dropped open, it might interfere  
with the shift lever or something else. If this happens, pay  
attention to safety and move the shift lever or take an  
appropriate action, then operate the unit.  
• Do not apply excessive force to the open faceplate or place  
objects on it. Doing so will cause damage or breakdown.  
• Do not use the unit with the faceplate in the open condition.  
Doing so will cause breakdown.  
Playing CDs  
Playing CDs:  
A press of the release button causes the faceplate to drop to  
the front, thereby exposing the CD slot.  
Egnlish  
Holding the CD with the labeled side facing up, insert it in the  
slot. The CD will start playing. Push back on the right side of  
the faceplate with your hand until it locks.  
The ¢ indicator will light when a CD has been inserted.  
2CAUTION  
When inserting a CD, make sure the CD has been completely  
drawn in before pushing back the faceplate. Failing to do so might  
scratch the CD.  
NOTE  
When you load a CD and eject it right away, the next time you try  
to insert the CD may not load. In such a situation, take the CD out  
for a moment and then reinsert it.  
Playing CDs Already Inserted:  
Press the SRC button repeatedly until the CD mode is obtained.  
"CD" is displayed when the CD mode has been selected.  
The CD will start playing.  
Pausing and Restarting CD Play:  
Press the 38 button to make the disc pause.  
Press the same button again to start play again.  
Playing Other Disc mode  
Eject:  
This function permits the connection of optional players and  
the playing of discs other than the loaded CD (in the current  
unit).  
Press the release button and drop open the faceplate.  
Press the 0 button located near the CD slot.  
The CD stops playing and ejects from the slot.  
Push back on the right side of the faceplate with your hand until  
it locks.  
Playing Discs:  
Press the SRC button repeatedly to select the external disc  
control mode.  
0
The disc will start playing.  
NOTE  
The external disc control mode will differ, depending on the unit  
that is connected.  
Mode Display Examples  
• "CD2"...when a CD player is connected  
• "DISC"...when a disc changer is connected  
• "DISC-1", "DISC-2"...when two disc changers are connected  
2CAUTION  
Pausing and Restarting Disc Play:  
Press the 38 button to make the disc pause.  
• Do not attempt to insert a CD into the slot if another one is  
already there.  
Press the same button again to start play again.  
— 20 —  
Making a Forward Track Search:  
NOTE  
Press the ¢ button to display the desired track number.  
Press once to fast forward to the next track, twice to fast  
forward to the track after that, and so forth.  
• When one disc has finished playing its last track, the next disc in  
the changer starts playing. When the last disc in the changer  
has finished, the player returns to the first disc and starts  
playing it.  
Play starts at the beginning of the displayed track number.  
NOTE  
• Disc #10 is displayed as "0".  
(For disc changers)  
You cannot make a forward track search when listening to the last  
track on a disc.  
Fast Forwarding and Reversing Disc Play  
Fast Forwarding Disc Play:  
Hold down on the ¢ button.  
Disc Search  
Search forwards or backwards through the discs in a disc  
changer until you reach the one that you want to listen to.  
(Function of disc changers)  
Release your finger to play the disc at that point.  
Reversing Disc Play:  
Hold down on the 4 button.  
Making a Reverse Disc Search:  
Release your finger to play the disc at the point.  
Press the DISCbutton to display the desired disc number.  
Each time the button is pressed, the displayed disc number  
decreases by one.  
NOTE  
You cannot use reverse play between tracks depending on the  
model being connected. Instead, the reverse play function is  
cancelled when it reaches the beginning of a track, at which point  
normal play automatically resumes.  
Play starts at the beginning of the displayed disc.  
Making a Forward Disc Search:  
Press the DISC+ button to display the desired disc number.  
Each time the button is pressed, the displayed disc number  
increases by one.  
Play starts at the beginning of the displayed disc.  
NOTE  
Track Search  
Search forwards or backwards through the tracks on the disc  
until you reach the one that you want to listen to.  
"LOAD" is displayed when discs are being exchanged on the disc  
changer.  
Making a Reverse Track Search:  
Press the 4 button to display the desired track number.  
Press once to search back to the beginning of the current track,  
twice to search back to the beginning of the previous track, and  
so forth.  
Play starts at the beginning of the displayed track number.  
NOTE  
(For disc changers)  
Pressing the 4 button whilst listening to track 1 only searches  
back to the beginning of that track. The reverse search is not  
"recycled" to the last track on the disc.  
— 21 —  
CD/External disc control features  
Track / Disc Repeat  
Repeat playing the current track or disc.  
Disc Scan  
(Function of disc changers)  
Successively play the beginning of each disc on a changer until  
you find the one that you want to listen to.  
Turning Repeat Play Function On/Off:  
Press the REP button to switch the repeat play function on and  
off as follows :  
Egnlish  
Starting the disc scan:  
Press the D.SCN button. "DSCN ON" is displayed and the first  
10 seconds of each disc are played, in the order in which they  
are loaded on the changer.  
Track Repeat ON  
The disc number currently being heard blinks in the display.  
Disc Repeat ON (Function of disc changers)  
Stopping to Listen to the Disc Being Scanned:  
Press the 38 or D.SCN button again to stop the scan and keep  
on listening to the disc normally.  
Track/Disc Repeat OFF  
NOTE  
"TREP ON" is displayed and the track number blinks in the  
display when track repeat is on.  
• The disc scan function is cancelled when you stop playing a  
"DREP ON" is displayed and the disc number blinks in the  
display when disc repeat is on.  
disc.  
• The disc scan function only scans each disc on the changer  
once.  
NOTE  
• "LOAD" is displayed when discs are being exchanged on the disc  
changer.  
The repeat play function is cancelled when you stop playing the  
disc.  
Track Scan  
Random Play  
Play all the tracks on the current disc in random order.  
Successively play the beginning of each track on a disc until  
you find the track that you want to listen to.  
1
Press the RDM button to switch the random play function on  
and off.  
Starting the Track Scan :  
Press the SCAN button. "TSCN ON" is displayed and the first 10  
seconds of each track are played, and the tracks are played in  
order.  
"RDM ON" is displayed when random play is turned on.  
The display of the track number changes continuously as the  
next track is being selected.  
The track number currently being heard blinks in the display.  
When the track has been selected, play starts.  
The selected track number blinks in the display as it is being  
played.  
Stopping to Listen to the Track Being Scanned:  
Press the 38 or SCAN button again to stop the scan and keep  
on listening to a track normally.  
NOTE  
(For disc changers)  
NOTE  
When all the tracks on a certain disc have been played using the  
random play function, the next disc on the changer starts playing  
(with the random play function still turned on).  
• The track scan function is cancelled when you stop playing a  
disc.  
• The track scan function only scans each track on a disc once.  
2
To change the track being heard, press the ¢ button.  
Another track is selected and played.  
— 22 —  
NOTE  
Text Scroll  
The random play function is cancelled when you stop playing a  
disc.  
This function permits the text to be scrolled and the entire text  
to be displayed. Switching between manual scrolling and  
automatic scrolling is permitted. The factory default is manual  
scrolling.  
To scroll manually:  
1
2
Press the DISP button to display the disc title or the track title.  
Magazine Random Play  
Play the tracks on all the discs in the disc changer in random  
order.  
(Function of disc changers)  
Holding down the DISP button for one second or more results  
in one scrolling display of the titles.  
Manual/Automatic scroll switching:  
1
1
Hold down the MENU button for one second or more.  
"MENU" is displayed and the menu mode is turned on.  
Press the M.RDM button to switch the magazine random play  
function on and off.  
"MRDM ON" is displayed when magazine random play is turned  
on.  
The display of the disc and track numbers change continuously  
as the next track is being selected.  
2
Press the ¢ button repeatedly to switch the function to be  
set to the text scroll function.  
Pressing the 4 button results in the functions being switched  
in the reverse order.  
When the disc/track has been selected, play starts.  
The selected disc/track number blinks in the display as it is  
being played.  
The text scroll function is displayed with "SCL Manu" or "SCL  
Auto".  
"SCL Manu" (Manual scrolling)  
"SCL Auto" (Automatic scrolling)  
NOTE  
This function is not available with the following models:  
KDC-C200/C300/C400/C301/C401  
3
4
Switching settings  
Press either the AM or FM button.  
The display and setting will change.  
2
To change the track being heard, press the ¢ button.  
Another disc/track is selected and played.  
Press the MENU button to end the menu mode.  
NOTE  
To scroll automatically:  
1
• The magazine random play function is cancelled when you stop  
playing a disc.  
• The time needed for random selection depends on the number  
of discs loaded in the disc magazine.  
Press the DISP button to display the disc title or the track title.  
The titles will be displayed in one scrolling display.  
NOTE  
When the disc or track to be played changes, the title is displayed  
in one scrolling display.  
2
Holding down the DISP button for one second or more results  
in one scrolling display of the titles.  
NOTE  
Only units with a CD text feature permit title display. (KDC-6070R  
only)  
— 23 —  
CD/External disc control features  
NOTE  
Presetting Disc Names  
The operation and characters that can be entered may change  
as listed below, depending on the unit that is connected.  
A press of the 38 button exits the disc name preset mode.  
Operations can be followed again from Step 2 at a time such  
as this, and the characters to be input are selected using the  
procedure described below.  
Press the DISC+ or DISCbutton to display the desired  
character. Besides the alphabet (capital letters only) and  
numbers, you can choose the following characters: /, +, , *,  
=, <, >, [ and ].  
Store the names of discs to be displayed when played.  
1
Play the disc whose name you want to preset.  
Egnlish  
NOTE  
• This function is not available for disc changers that do not  
feature the Disc Name Preset function.  
• This procedure is not to be used to store the disc and track titles  
for MDs that you record.  
2
Hold down the NAME.S button for two seconds or more.  
"NAME SET" is displayed and the disc name preset mode is  
5
6
Continue steps 3 and 4 until all the characters are chosen for  
the name.  
entered.  
The cursor blinks in the position where character input can be  
made.  
Press either the NAME.S button on the main unit or the OK  
button on the remote control.  
3
4
Press either the 4 or ¢ button to move the cursor to the  
desired position.  
The disc name is stored and the disc name preset mode is  
cancelled.  
The 4 button moves the cursor to the left, and the ¢  
If you make no entry in a 10-second period, the name will be  
stored with the characters input so far.  
button to the right.  
You can also move the cursor left or right by pressing the  
TRACK+ or TRACKbuttons, respectively, on the remote  
control.  
NOTE  
• The number of characters and discs whose names can be  
stored will differ depending on the disc changer that is  
connected. Please see your disc changer manual for details.  
Up to 12 characters and 30 CDs can be registered with this unit.  
• Discs are identified by their total length and number of tracks. If  
another disc happens to have the same specifications as one  
that you have already stored a name for, the name will be  
displayed for it, too.  
• If you want to change the name of a disc, repeat steps 1 and 2  
to display the name, and then repeat steps 3 and 4 to input the  
changes.  
• Pressing the reset button erases the disc names stored in this  
unit, but does not erase the names stored in a disc changer.  
Each time the 38 button is pressed, the characters to be  
entered change as listed below.  
Press the DISC+ or DISCbutton to display the desired  
character.  
Characters that can be displayed are as follows.  
Alphabet (upper case): A ~ Z  
Alphabet (lower case): a ~ z (KDC-6070R Only)  
Numerals and symbols: 1~9 0 @ ” ‘ ` % & + - = , . / \ < > [ ]  
Special characters: á  
à
é
è
í
ì
ó
ò
ú
ù
Ñ
Ç
ë
î
ï
ô
ö
û
ü
ñ
ç
©
Æ
(KDC-6070R Only)  
— 24 —  
Other features  
Release button  
Switching Display for Discs  
Switch the display that appears whilst discs are playing.  
4
SRC FM/CLK  
¢
POWER  
OFF  
SRC  
Switching Display for Discs:  
CLK  
FM  
AM  
Each time you press the DISP button, the display during disc  
play switches as follows.  
DISC  
PTY  
T
E
X
T
NAME.S  
TI VOL ADJ DISP  
DISC  
ATT  
LOUD  
SCAN  
RDM  
REP  
D.SCN  
M.RDM  
MENU  
Track time  
1
2
3
4
5
6
AUD  
Total disc playing time (CD only) (KDC-5070R only)  
Disc name (DNPS)  
AUD / MENU AM  
for KDC-6070R  
Disc title (Units featuring CD text/MD only)  
Track title (Units featuring CD text/MD only)  
Clock display  
Clock (KDC-5070R only)  
NOTE  
• You can give names to discs through the presetting disc name  
function (see p24).  
I
Note that depending on the unit, display may not be possible.  
• If you try to display the name of a disc that does not have one,  
"NO NAME" is displayed instead.  
• When there is an attempt to display the title of a disc for which  
the disc title/track title has not been recorded, "NO TEXT" is  
displayed for CD and "NO NAME" is displayed for MD.  
• Depending on the type of characters of the CD Text, some  
characters may not be displayable.  
for KDC-5070R  
Clock display  
I
£ indicator  
— 25 —  
Other features  
Function of the KDC-5070R  
Audio Control Setting  
Adjust various parameters of sound quality.  
Switching Clock Display  
This function permits switching the clock display on/off when  
switching the display during each of the modes.  
1
2
Press the AUD button to enter the control mode.  
Egnlish  
Press either the FM or AM button.  
Turning the Clock Display On/Off:  
1
Each time the button is pressed, the adjustment mode will  
change as follows:  
Hold down the MENU button for one second or more.  
"MENU" is displayed and the menu mode is turned on.  
Pressing the FM button advances the display, and pressing the  
AM button reverses it.  
2
Press the ¢ button repeatedly until the Switching Clock  
Display function appears in the display.  
Press the 4 button to search in the other direction.  
The function setting is indicated by "CLK ON" or "CLK OFF" in  
the display, indicating that the Clock Display function is on or  
off, respectively.  
Fader  
Bass  
Treble  
Balance  
NOTE  
3
4
Switching settings  
Source tone memory  
Press either the AM button or FM button .  
The display and setting will change.  
Each source (CD, FM, AM, and disc changer) has its own memory  
in which to store the bass and treble tone settings.  
The settings made for a particular source are then recalled  
automatically whenever you use that source (e.g., FM mode uses  
the tone settings made for FM, AM for AM, etc.).  
Press the MENU button to end the menu mode.  
3
Press the 4/¢ button.  
Look at the table to adjust the mode being displayed.  
Function of the KDC-6070R  
Adjustment  
mode  
Operation of Audio control button  
Switching Graphic Display  
This function permits the graphic display to be switched to one  
that is linked with the volume level value or to display various  
modes. The initial setting is ON (displaying various modes).  
4 button  
Bass decreased.  
¢ button  
(Display)  
Bass ("BAS")  
Treble("TRE")  
Balance("BAL")  
Fader ("FAD")  
Bass increased.  
Treble decreased.  
Left channel emphasized.  
Rear channel increased.  
Treble increased.  
Turning the Graphic Display On/Off:  
1
Hold down the MENU button for one second or more.  
"MENU" is displayed and the menu mode is turned on.  
Right channel emphasized.  
Front channel increased.  
2
Press the ¢ button repeatedly until the Switching Graphic  
Display function appears in the display.  
4
Press the AUD button to end the control mode.  
Press the 4 button to search in the other direction.  
The function setting is indicated by "GRAP ON" or "GRAP OFF"  
in the display, indicating that the Graphic display is on or off,  
respectively.  
"GRAP ON" (The graphic display works.)  
"GRAP OFF" (The graphic display does not work.)  
— 26 —  
3
4
3
4
Switching settings  
Switching settings  
Press either the AM button or FM button.  
The display and setting will change.  
Press either the AM or FM button.  
The display and setting will change.  
Press the MENU button to end the menu mode.  
Press the MENU button to end the menu mode.  
NOTE  
When making audio adjustments, even when this function is on,  
the display will be linked to the audio adjustment value, not the  
display of the various modes.  
TEL Mute  
Shut down the audio system temporarily whenever an  
incoming call is received.  
NOTE  
Function of the KDC-6070R  
The function will not work if a cable is not connected to the car  
phone.  
Clock display  
Turning clock display On/Off:  
When the telephone rings:  
Each time you hold down the CLK button for one second or  
more, the display switches between the clock and each mode  
display.  
When a call is received, "CALL" is displayed and all the unit  
functions are temporarily interrupted.  
Restoring Original Unit Source During Phone Call:  
Press the SRC button.  
"CALL" disappears from the display, and the volume of the  
original source is restored gradually.  
Function of the KDC-6070R  
Turning TEL Mute Function Off After Phone Call:  
Hang the phone up.  
Dimmer  
You can dim the display.  
"CALL" disappears from the display.  
The original source (i.e., the one used before the phone call) is  
returned to automatically, and the volume restored gradually.  
NOTE  
The dimmer function is not available for units if the dimmer cable  
is not connected.  
Turning Dimmer On/Off:  
1
Hold down the MENU button for one second or more.  
"MENU" is displayed and the menu mode is turned on.  
2
Press the ¢ button repeatedly until the Dimmer function  
appears in the display.  
Press the 4 button to search in the other direction.  
The function setting is indicated by "DIM ON" or "DIM OFF" in  
the display, indicated that the current dimmer setting is on or  
off, respectively.  
— 27 —  
Other features  
NOTE  
Selectable Illumination  
The beep sound is not output from the preout jacks.  
You can switch the colour of the button illumination between  
green and amber.  
Egnlish  
1
2
Hold down the MENU button for one second or more.  
"MENU" is displayed and the menu mode is turned on.  
Function of the KDC-6070R  
Press the ¢ button repeatedly until the Selectable  
Illumination function appears in the display.  
Press the 4 button to search in the other direction.  
The function setting is indicated by "COL GRN" or "COL AMB" in  
the display, indicating that the current colour is green or amber,  
respectively.  
Contrast Adjustment  
This adjustment permits easy viewing of the display.  
To adjust the contrast:  
1
Hold down the MENU button for one second or more.  
"MENU" is displayed and the menu mode is turned on.  
3
4
Switching settings  
Press either the AM button or FM button.  
The display and setting will change.  
2
Press the ¢ button repeatedly until the Contrast Adjustment  
function appears in the display.  
Press the 4 button to search in the other direction.  
The function setting is indicated by "CONT ##" in the display,  
indicating that the Contrast Adjustment mode is on.  
Press the MENU button to end the menu mode.  
3
4
Switching settings  
Press either the AM or FM button.  
Press the FM button to change the setting values higher, and  
press the AM button to change them lower. Settings may be  
made from 0 to 10.  
Touch Sensor Tone  
This function produces a beep sound that accompanies button  
operation. It can be switched on or off.  
Press the MENU button to end the menu mode.  
Turning the Beep On/Off:  
NOTE  
1
Hold down the MENU button for one second or more.  
"MENU" is displayed and the menu mode is turned on.  
The "##" display in the contrast adjustment mode will differ  
depending on the setting. The initial setting value is "5".  
2
Press the ¢ button repeatedly until the Touch Sensor Tone  
function appears in the display.  
Press the 4 button to search in the other direction.  
The function setting is indicated by "Beep ON" or "Beep OFF" in  
the display, indicating that the current beep setting is on or off,  
respectively.  
Adjusting Time  
With automatic time adjustment, you can set the clock time  
automatically according to time data sent from RDS stations  
(after receiving RDS signals for several minutes). You can also  
set the time manually if the automatic time adjustment function  
is turned off. The factory default is automatic time adjustment.  
3
4
Switching settings  
Press either the AM or FM button.  
The display and setting will change.  
Press the MENU button to end the menu mode.  
— 28 —  
Adjusting Time Automatically:  
Press the ¢ button to advance the minutes, or press the  
Tune into an RDS station for 3 or 4 minutes.  
The time adjusts automatically to the correct local time.  
4 button to make the minutes go back.  
6
Press the MENU button to end the menu mode.  
NOTE  
The time is not adjusted when the RDS station you are tuned to is  
not transmitting a time signal. Choose another RDS station in  
such a case.  
Disabled System Indicator (DSI)  
A red indicator blinks on the unit after the faceplate is removed,  
warning potential thieves. The factory default for this function  
is "ON".  
Turning Automatic Time Adjustment On/Off:  
1
Hold down the MENU button for one second or more.  
"MENU" is displayed and the menu mode is turned on.  
Turning Disabled System Indicator On/Off:  
2
Press the ¢ button repeatedly until the Automatic Time  
Adjustment function appears in the display.  
Press the 4 button to search in the other direction.  
The function setting is indicated by "SYNC ON" or "SYNC OFF"  
in the display, indicating that the Automatic Time Adjustment is  
on or off, respectively.  
1
Hold down the MENU button for one second or more.  
"MENU" is displayed and the menu mode is turned on.  
2
Press the ¢ button repeatedly until the Disabled System  
Indicator function appears in the display.  
Press the 4 button to search in the other direction.  
The function setting is indicated by "DSI ON" or "DSI OFF" in the  
display, indicating that the disable system indicator is on or off,  
respectively.  
"SYNC ON" (Automatic time adjustment)  
"SYNC OFF" (Manual time adjustment)  
3
4
Switching settings  
Press either the AM button or FM button.  
The display and setting will change.  
3
4
Switching settings  
Press either the AM button or FM button.  
The display and setting will change.  
Press the MENU button to end the menu mode.  
Press the MENU button to end the menu mode.  
Adjusting Time Manually:  
1
2
Turn off the Automatic Time Adjustment as mentioned above.  
Hold down the MENU button for one second or more.  
"MENU" is displayed and the menu mode is turned on.  
3
4
5
Press the ¢ button repeatedly until the "CLK ADJ" appears in  
the display.  
Press the 4 button to search in the other direction.  
Hold down either the AM or FM button for two seconds or  
more to enter the Time Adjustment mode.  
The hour display will blink.  
• Adjusting the hours  
Press the FM button to advance the hours, or press the AM  
button to make the hours go back.  
• Adjusting the minutes  
— 29 —  
Other features  
£
Theft Deterrent Faceplate  
The faceplate of the unit can be detached and taken with you,  
helping to deter theft.  
Egnlish  
Removing Faceplate:  
Shaft  
Press the release button and drop open the faceplate.  
In its dropped condition, whilst drawing the faceplate to one  
side, pull it to the front and remove it.  
Depression  
£
Release button  
POWER  
OFF  
SRC  
CLK  
FM  
Function of the KDC-6070R  
DISC  
PTY  
T
E
X
T
Automatic Dimmer Function  
DISC  
ATT  
LOUD  
SCAN  
RDM  
REP  
D.SCN  
M.RDM  
AM  
MENU  
AUD  
1
2
3
4
5
6
The display dims when the car's lights are turned on.  
NOTE  
NOTE  
The dimmer function is not available for units if the dimmer cable  
is not connected.  
• The faceplate is a precision piece of equipment and can be  
damaged by shocks or jolts. For that reason, keep the faceplate  
in its special storage case whilst detached.  
• Do not expose the faceplate or its storage case to direct  
sunlight or excessive heat or humidity. Also avoid places with  
too much dust or the possibility of water splashing.  
Navigation Mute Function  
When the KENWOOD Navigation System is connected, an  
interruption of the audio guide results in the temporary  
lowering of the audio level.  
Reattaching Faceplate:  
Hold the faceplate so that the operation face faces the front  
toward you and press until it locks. The faceplate will be set  
and the unit will be operational.  
NOTE  
The Navigation mute function cannot be used unless a TEL mute  
cable is connected to the KENWOOD Navigation System.  
NOTE  
When there is difficulty in setting the faceplate, align the  
depression on the left side of the faceplate with the shaft of the  
unit, then lock.  
— 30 —  
Accessories  
External view  
Number of items  
2CAUTION  
• If your car is not prepared for this special connection-system,  
consult your Kenwood dealer.  
1
..........................................1  
• Only use antenna conversion adapters (ISO-JASO) when the  
antenna cord has an ISO plug.  
• Make sure that all cable connections are securely made by  
inserting jacks until they lock completely.  
..........................................2  
..........................................1  
2
3
• If your vehicle's ignition does not have an ACC position, or if  
the ignition cable is connected to a power source with constant  
voltage such as a battery cable, the power will not be linked  
with the ignition (i.e., it will not turn on and off along with the  
ignition). If you want to link the unit's power with the ignition,  
connect the ignition cable to a power source that can be turned  
on and off with the ignition key.  
2CAUTION  
• If the fuse blows, first make sure that the cables have not  
caused a short circuit, then replace the old fuse with one with  
the same rating.  
• Do not let unconnected cables or terminals touch metal on the  
car or anything else conducting electricity. To prevent short  
circuits, also do not remove the caps on the ends of the  
unconnected cables or the terminals.  
• Connect the speaker cables correctly to the terminals to which  
they correspond. The unit may receive damage or fail to work if  
you share the - cables and/or ground them to any metal part in  
the car.  
• After the unit is installed, check whether the brake lamps,  
indicators, wipers, etc. on the car are working properly.  
• Insulate unconnected cables with vinyl tape or other similar  
material.  
The use of any accessories except for those provided might result  
in damage to the unit. Make sure only to use the accessories  
shipped with the unit, as shown above.  
Installation Procedure  
1. To prevent short circuits, remove the key from the ignition and  
disconnect the -terminal of the battery.  
2. Make the proper input and output cable connections for each unit.  
3. Connect the cable on the wiring harness.  
4. Take Connector B on the wiring harness and connect it to the  
speaker connector in your vehicle.  
5. Take Connector A on the wiring harness and connect it to the  
external power connector on your vehicle.  
6. Connect the wiring harness connector to the unit.  
7. Install the unit in your car.  
• Some disc changers need conversion cables for connection.  
See the section on "Safety Precautions" for details.  
• If the console has a lid, make sure to install the unit so that the  
faceplate does not hit the lid when closing and opening.  
• Mount the unit so that the mounting angle is 30° or less.  
8. Reconnect the - terminal of the battery.  
9. Press the reset button.  
— 31 —  
Connecting Cables to Terminals  
Antenna Conversion Adaptor (ISO–JASO) (Accessory3)  
Antenna Cord (ISO)  
FM/AM antenna input  
E
Rear left output  
(White)  
Connector Function Guide  
Pin Numbers for  
ISO Connectors  
Cable Colour  
Functions  
Front left  
output (White)  
External Power  
Connector  
A–4  
A–5  
A–6  
A–7  
A–8  
Yellow  
Blue/White  
Orange/White Dimmer  
Red  
Battery  
Power Control  
Front right  
output (Red)  
Fuse (10A)  
Ignition (ACC)  
Earth (Ground)  
Connection  
KENWOOD disc changer  
/ DAB control input  
Rear right  
output (Red)  
Black  
NOTE  
Speaker  
Connector  
B–1  
To connect the Disc  
changer or DAB unit,  
consult each manual.  
Wiring harness  
Purple  
Purple/Black  
Gray  
Gray/Black  
White  
White/Black  
Green  
Rear Right (+)  
Rear Right ()  
Front Right (+)  
Front Right ()  
Front Left (+)  
Front Left ()  
Rear Left (+)  
Rear Left ()  
(Accessory1)  
Connect to the terminal that is  
grounded when either the  
telephone rings or during  
conversation.  
B–2  
B–3  
B–4  
B–5  
B–6  
B–7  
B–8  
TEL MUTE  
TEL mute cable (Brown)  
NOTE  
To connect the KENWOOD  
navigation system, consult  
your navigation manual.  
Battery cable (Yellow)  
Ignition cable (Red)  
Green/Black  
If no connections are made,  
do not let the cable come  
out from the tab.  
Connect either to the power  
control terminal when using the  
optional power amplifier, or to  
the antenna control terminal in  
the vehicle.  
ANT.C  
A–7 Pin (Red)  
P.CONT  
A–4 Pin (Yellow)  
Power control/ Motor  
antenna control  
cable (Blue/White)  
Connector A  
Connector B  
8
7
6
5
4
3
2
1
8
7
6
5
4
3
2
1
— 32 —  
2WARNING  
NOTE  
Connecting the ISO Connector (see p.32)  
The pin arrangement for the ISO connectors depends on the type  
of vehicle you drive. Make sure to make the proper connections to  
prevent damage to the unit.  
The default connection for the wiring harness is described in 1  
below. If the ISO connector pins are set as described in 2 or 3,  
make the connection as illustrated.  
When the connection is made as in 3, the unit's power will not be  
linked to the ignition key. For that reason, always make sure to  
turn off the unit's power when the ignition is turned off.  
To link the unit's power to the ignition, connect the ignition cable  
(ACC...red) to a power source that can be turned on and off with  
the ignition key.  
1 (Default setting) The A-7 pin (red) of the vehicle's ISO  
connector is linked with the ignition, and the A-4 pin (yellow) is  
connected to the constant power supply.  
Unit  
Vehicle  
A–7 Pin (Red)  
Installation  
Ignition cable (Red)  
Installation  
Battery cable (Yellow)  
A–4 Pin (Yellow)  
Firewall or metal support  
2 The A-7 pin (red) of the vehicle's ISO connector is connected to  
the constant power supply, and the A-4 pin (yellow) is linked to  
the ignition.  
Screw (M4X8)  
(commercially  
available)  
Unit  
Vehicle  
Ignition cable (Red)  
A–7 Pin (Red)  
Battery cable (Yellow)  
A–4 Pin (Yellow)  
3 The A-4 pin (yellow) of the vehicle's ISO connector is not  
connected to anything, while the A-7 pin (red) is connected to  
the constant power supply (or both the A-7 (red) and A-4  
(yellow) pins are connected to the constant power supply).  
Bend the tabs of the  
mounting sleeve with  
a screwdriver or  
similar utensil and  
attach it in place.  
Self-tapping  
screw  
(commercially  
available)  
Metal mounting  
strap  
(commercially  
available)  
Unit  
Vehicle  
Ignition cable (Red)  
A–7 Pin (Red)  
Battery cable (Yellow)  
A–4 Pin (Yellow)  
NOTE  
Make sure that the unit is installed securely in place. If the unit is  
unstable, it may malfunction (eg, the sound may skip).  
— 33 —  
Installation  
Removing the hard rubber frame  
Removing the Unit  
1
Refer to the section “Removing the hard rubber frame” and  
then remove the hard rubber frame.  
1
Engage the catch pins on the removal tool and remove the two  
locks on the lower level.  
Lower the frame and pull it forward as shown in the figure.  
2
3
Remove the screw (M4×8) on the back panel.  
Egnlish  
Insert the two removal tools deeply into the slots on each side,  
as shown.  
Catch  
Lock  
Catch facing up  
Screw (M4X8)  
(commercially  
available)  
Accessory2 Removal tool  
2
When the lower level is removed, remove the upper two  
locations.  
4
Lower the removal tool  
toward the bottom, and pull  
out the unit halfway whilst  
pressing towards the  
inside.  
2CAUTION  
Be careful to avoid injury from the catch pins on the removal tool.  
NOTE  
5
Pull the unit all the way out  
with your hands, being  
careful not to drop it.  
The frame can be removed from the top side in the same  
manner.  
— 34 —  
Troubleshooting Guide  
What might appear to be a malfunction in your unit may just be the result of slight misoperation or miswiring. Before  
calling service, first check the following table for possible problems.  
PROBLEM  
POSSIBLE CAUSE  
SOLUTION  
The power does not turn on.  
The fuse has blown.  
After checking for short circuits in the cables, replace the  
fuse with one having the same rating.  
No ACC position on vehicle ignition.  
The Attenuator function is turned on.  
Connect the same cable to the ignition as the battery cable.  
Turn off the Attenuator function.  
No sound can be heard, or the  
volume is low.  
The fader and/or balance settings are set all the way to  
one side.  
Reset the fader and/or balance settings.  
The input/output cables or wiring harness are connected  
incorrectly.  
Reconnect the input/output cables and/or the wiring harness  
correctly. See the section on "Connecting Cables to  
Terminals".  
Nothing happens when the  
buttons are pressed.  
The computer chip in the unit is not functioning normally.  
Press the reset button on the unit (see page 4).  
Check the speaker wiring.  
A speaker cable may be pinched by a screw in the car.  
The speakers are not wired correctly.  
The sound quality is poor or  
distorted.  
Reconnect the speaker cables so that each output terminal  
is connected to a different speaker.  
Radio reception is poor.  
The car antenna is not extended.  
Pull out the antenna all the way.  
The antenna control cable is not connected.  
Connect the cable correctly, referring to the section on  
"Connecting Cables to Terminals".  
The memory is erased when  
the ignition is turned off.  
The battery cable has not been connected to the proper  
terminal.  
Connect the cable correctly, referring to the section on  
"Connecting Cables to Terminals".  
The ignition and battery cable are incorrectly connected.  
Connect the cable correctly, referring to the section on  
"Connecting Cables to Terminals".  
The TEL mute function does  
not work.  
The TEL mute cable is not connected properly.  
Connect the cable correctly, referring to the section on  
"Connecting Cables to Terminals".  
The TEL mute function turns on  
even though the TEL mute  
cable is not connected.  
The TEL mute cable is touching a metal part of the car.  
Pull the TEL mute cable away from the metal part of the car.  
— 35 —  
Troubleshooting Guide  
PROBLEM  
POSSIBLE CAUSE  
SOLUTION  
A CD ejects as soon as it is  
loaded.  
The CD is upside-down.  
Load the CD with the labelled side up.  
Egnlish  
The CD is quite dirty.  
Clean the CD, referring to the section on "Cleaning CDs" (see  
page 5).  
The sound skips on a CD.  
The CD is scratched or dirty.  
Random play has been selected.  
Clean the CD, referring to the section on "Cleaning CDs" (see  
page 5).  
The specified track does not  
play.  
Turn off the random play function.  
External disc control mode  
PROBLEM  
POSSIBLE CAUSE  
SOLUTION  
The disc control mode cannot  
be selected.  
No cable has been connected to the disc changer input  
terminal on the unit.  
Connect the cable to the disc changer input terminal on the  
unit.  
The specified disc does not  
play, but another one plays  
instead.  
The specified CD is very dirty.  
Clean the CD.  
The CD is upside-down.  
Load the CD with the labelled side up.  
The disc is loaded in a different slot from that specified.  
Eject the disc magazine and check the number for the  
specified disc.  
The disc is severely scratched.  
Something is touching the disc changer.  
The CD is scratched or dirty.  
Try another disc instead.  
The sound skips.  
Remove whatever is touching it.  
If skipping happens at the same place when the car is  
stopped, something is wrong with the CD. Clean the CD.  
The display shows that the  
changer is being played, but no  
sound can be heard.  
The computer chip in the unit is not functioning normally.  
Random play or magazine random play has been selected.  
Press the reset button on the unit (see page 4).  
The specified track does not  
play.  
Turn off the random play or magazine random play function.  
If the following situations, consult your nearest service centre:  
• Even though the disc changer is connected, the Disc Changer Mode is not on, with "AUX" showing in the display during the Changer Mode.  
• Even though no device (KCA-S210A, CA-C1AX, KDC-CPS82 or KDC-CX82) is connected, the AUX Mode is entered when switching modes.  
— 36 —  
The following messages are displayed when certain problems are occurring in your system. Take the recommended  
actions.  
No disc magazine has been loaded in the changer. The disc magazine is not completely loaded.  
EJECT  
]
Load the disc magazine properly.  
No CD in the unit.  
]
Insert the CD.  
No disc has been loaded in the disc magazine.  
NO DISC  
E-04  
]
Load a disc into the disc magazine.  
No disc has been loaded in the disc magazine.  
]
Load a disc into the disc magazine.  
The CD is very dirty. The CD is upside-down. The CD is scratched a lot.  
]
Clean the CD and load it correctly.  
Nothing has been recorded on the MD.  
BLANK  
NO TRACK  
NO PANEL  
E-77  
]
The next MD is automatically played back  
No tracks are recorded on the MD, although it has a title.  
]
The next MD is automatically played back.  
The faceplate of the slave unit being connected to this unit has been removed.  
]
Replace it.  
The unit is malfunctioning for some reason.  
]
Press the reset button on the unit. If the "E- 77", code does not disappear, consult your nearest service centre.  
Something is wrong with the disc magazine. Or the unit is malfunctioning for some reason.  
E-99  
]
Check the disc magazine. And then, press the reset button on the unit.  
If the "E- 99" code does not disappear, consult your nearest service center.  
The protective circuit in the unit activates when the temperature inside the automatic disc changer exceeds 60°C (140°F), stopping  
all operation.  
HOLD  
]
Cool down the unit by opening the windows or turning on the air conditioner. As the temperature falls below 60°C (140°F), the  
disc starts playing again.  
— 37 —  
Specifications  
Specifications subject to change without notice.  
FM tuner section  
Audio section  
Frequency Range (50 kHz Space) ..................87.5MHz-108.0MHz  
Usable Sensitivity (S/N: 26dB)....................................0.7 µV/75  
Quieting Sensitivity (S/N: 46dB) .................................1.6 µV/75 Ω  
Frequency Response ( 3.0dB)...................................30Hz-15kHz  
Signal to Noise ratio ...............................................65dB(MONO)  
Selectivity (DIN)...............................................80 dB( 400 kHz)  
Stereo Separation .......................................................35dB(1kHz)  
Maximum output power  
KDC-6070R...............................................................44wx4  
KDC-5070R...............................................................40wx4  
Full Bandwidth Power (DIN45324,+B=14.4V )  
KDC-6070R...............................................................27wx4  
KDC-5070R...............................................................25wx4  
Tone action  
Egnlish  
Bass .............................................................100Hz 10dB  
Treble ...........................................................10kHz 10dB  
Preout Level(mV)/Load ...........................................1800mV/10kΩ  
.................................................(during disc changer mode)  
Preout Impedance..............................................................600Ω  
MW tuner section  
Frequency Range (9 kHz space)..........................531kHz-1611kHz  
Usable Sensitivity (S/N: 20dB) .............................................25 µV  
LW tuner section  
Frequency Range .................................................153kHz-281kHz  
Usable Sensitivity (S/N: 20dB) .............................................45 µV  
General  
Operating voltage (11 - 16V allowable) .................................14.4v  
Current Consumption .............................................................10A  
Installation Size (W x H x D) ...........................182 x 53 x 160 mm  
Weight................................................................................1500g  
CD player section  
Laser diode ....................................................GaAlAs (λ=780 nm)  
Digital filter (D/A).......................................8 Times OverSampling  
D/A Converter .......................................................................1 Bit  
Spindle speed...............................................500 – 200 rpm (CLV)  
Wow & Flutter..........................................Below Mesurable Limit  
Frequency response ....................................10Hz - 20kHz ( 1 dB)  
Total harmonic distortion ..........................................0.01%(1kHz)  
Signal to Noise ratio....................................................93dB(1kHz)  
Dynamic range .....................................................................93dB  
Channel separation...............................................................85dB  
— 38 —  
— 39 —  

Pioneer CD RDS RECEIVER DEH 73BT User Manual
Philips RI7633 User Manual
Panasonic CQ C9801U User Manual
Panasonic Blu ray Player BDP LX55 User Manual
Nikon D7000 User Manual
Nikon 2192B User Manual
NEC MultiSync LCD1735NXM User Manual
Krups KB790 User Manual
Kenwood KVT 767DVD User Manual
Kenwood KRC 603C User Manual