Dear Customer,
Thank you for purchasing this digital
video camera. Before use, please
read the safety information and
precautions contained in the pages
3 – 5 to ensure safe use of this
product.
ENGLISH
DIGITAL VIDEO CAMERA
GETTING STARTED
7
GR-D790U
RECORDING & PLAYBACK
18
DIGITAL STILL CAMERA
(D.S.C.) RECORDING &
For Accessories:
PLAYBACK
26
31
46
52
ADVANCED FEATURES
REFERENCES
TERMS
For Customer Use:
Enter below the Model No. and
Serial No. which is located on the
bottom of the camcorder. Retain
this information for future reference.
Model No.
Serial No.
To deactivate the demonstration,
set “DEMO MODE” to “OFF”.
(੬ pg. 31, 34)
INSTRUCTIONS
LYT1643-001A
EN
3
Read This First!
● Before recording important video, be sure to ● It is recommended that you use JVC brand
make a trial recording.
cassette tapes.
Play back your trial recording to make sure the
video and audio have been recorded properly.
● We recommend cleaning your video heads
before use.
Your camcorder is compatible with all brands of
commercially available cassette tapes
complying with the MiniDV standard, but JVC
brand cassette tapes are designed and
optimized to maximize the performance of your
camcorder.
If you haven’t used
your camcorder for
awhile, the heads may
● Remember that this camcorder is intended
for private consumer use only.
Any commercial use without proper permission
is prohibited. (Even if you record an event such
as a show, performance or exhibition for
personal enjoyment, it is strongly recommended
that you obtain permission beforehand.)
● DO NOT leave the unit
be dirty. We
recommend
periodically cleaning
the video heads with a
cleaning cassette
(optional).
● Be sure to store your cassette tapes and
camcorder in the proper environment.
Video heads can become dirty more easily if
your cassette tapes and camcorder are stored
in a dusty area. Cassette tapes should be
removed from the camcorder and stored in
cassette cases. Store the camcorder in a bag or
other container.
- in place of over 50°C (122°F)
- in place where humidity is extremely low
(below 35%) or extremely high (80%).
- in direct sunlight.
- in a closed car in summer.
- near a heater.
● The LCD monitor is made with high-
precision technology. However, black spots
or bright spots of light (red, green or blue)
may appear constantly on the LCD monitor.
These spots are not recorded on the tape.
This is not due to any defect of the unit.
(Effective dots: more than 99.99%)
● Do not leave the battery pack attached when
the camcorder is not in use and check the
unit regularly whether it is working or not.
● Use SP (Standard) mode for important video
recordings.
LP (Long Play) mode lets you record 50% more
video than SP (Standard) mode, but you may
experience mosaic-like noise during playback
depending on the tape characteristics and the
usage environment.
So, for important recordings, we recommend
using SP mode.
● For safety and reliability.
It is recommended only genuine JVC batteries
and accessories are used in this camcorder.
● This product includes patented and other
proprietary technology and will operate only
with JVC Data Battery. Use the JVC
BN-VF808U/VF815U/VF823U battery packs.
Using generic non-JVC batteries can cause
damage to the internal charging circuitry.
● This camcorder is designed exclusively for
the digital video cassette, SD Memory Card
and MultiMediaCard. Only cassettes marked
Also read “CAUTIONS” on pages 48 – 50.
● Microsoft® and Windows® are either registered
trademarks or trademarks of Microsoft
Corporation in the United States and/or other
countries.
● Macintosh is a registered trademark of Apple
Computer, Inc.
● QuickTime is a registered trademark of Apple
Computer, Inc.
“
” and memory cards marked “
” can be used with this
”
or “
unit.
● SDHC Memory Card cannot be used with
this camcorder.
● Remember that this camcorder is not
compatible with other digital video formats.
4
EN
SAFETY PRECAUTIONS
NOTES:
● The rating plate (serial number plate) and
safety caution are on the bottom and/or the
back of the main unit.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
● The rating information and safety caution of the
AC Adapter are on its upper and lower sides.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
When the equipment is installed in a cabinet or on a
shelf, make sure that it has sufficient space on all
sides to allow for ventilation (10 cm (3-15/16") or
more on both sides, on top and at the rear).
Do not block the ventilation holes.
(If the ventilation holes are blocked by a
newspaper, or cloth etc. the heat may not be able
to get out.)
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated "dangerous voltage" within the
product's enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
No naked flame sources, such as lighted
candles, should be placed on the apparatus.
When discarding batteries, environmental
problems must be considered and the local rules
or laws governing the disposal of these batteries
must be followed strictly.
WARNING:TO PREVENT FIRE OR SHOCK
HAZARD, DO NOT EXPOSE THIS UNIT TO
RAIN OR MOISTURE.
The apparatus shall not be exposed to dripping
or splashing.
Do not use this equipment in a bathroom or
places with water.
Also do not place any containers filled with water
or liquids (such as cosmetics or medicines,
flower vases, potted plants, cups etc.) on top of
this unit.
(If water or liquid is allowed to enter this
equipment, fire or electric shock may be caused.)
CAUTIONS:
● This camcorder is designed to be used with
NTSC-type color television signals. It cannot
be used for playback with a television of a
different standard. However, live recording and
LCD monitor/viewfinder playback are possible
anywhere.
● This product includes patented and other
proprietary technology and will operate only
with JVC Data Battery. Use the JVC
BN-VF808U/VF815U/VF823U battery packs
and, to recharge them or to supply power to
the camcorder from an AC outlet, use the
provided multi-voltage AC Adapter. (An
appropriate conversion adapter may be
necessary to accommodate different designs
of AC outlets in different countries.)
Do not point the lens or the viewfinder directly
into the sun. This can cause eye injuries, as well
as lead to the malfunctioning of internal circuitry.
There is also a risk of fire or electric shock.
CAUTION!
The following notes concern possible physical
damage to the camcorder and to the user.
This product contains a CR Coin Cell Lithium
Battery which contains Perchlorate Material -
special handling may apply.
perchlorate
When carrying, be sure to always securely attach
and use the provided strap. Carrying or holding
the camcorder by the viewfinder and/or the LCD
monitor can result in dropping the unit, or in a
malfunction.
Take care not to get your finger caught in the
cassette holder cover. Do not let children operate
the camcorder, as they are particularly
susceptible to this type of injury.
Do not use a tripod on unsteady or unlevel
surfaces. It could tip over, causing serious
damage to the camcorder.
Caution on Replaceable lithium battery
The battery used in this device may present a fire
or chemical burn hazard if mistreated.
Do not recharge, disassemble, heat above 100°C
(212°F) or incinerate.
Replace battery with Panasonic (Matsushita
Electric), Sanyo, Sony or Maxell CR2025.
Danger of explosion or Risk of fire if the battery is
incorrectly replaced.
CAUTION!
Connecting cables (Audio/Video, S-Video, etc.) to
the camcorder and leaving it on top of the TV is
not recommended, as tripping on the cables will
cause the camcorder to fall, resulting in damage.
● Dispose of used battery promptly.
● Keep away from children.
● Do not disassemble and do not dispose of in fire.
USER MAINTENANCE
EN
5
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
Cleaning The Camcorder
Before cleaning, turn off the camcorder and
remove the battery pack and AC Adapter.
4. Follow all instructions.
To clean the exterior
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install
in accordance with the manufacturer’s
instructions.
8. Do not install near any heat sources such as
radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce
heat.
Wipe gently with a soft cloth. Put the cloth in
diluted mild soap and wring it well to wipe off
heavy dirt. Then wipe again with a dry cloth.
To clean the LCD monitor
Wipe gently with a soft cloth. Be careful not to
damage the monitor. Close the LCD monitor.
To clean the lens
Blow it with a blower brush, then wipe gently
with lens cleaning paper.
9. Only use attachments/accessories specified
by the manufacturer.
10. Use only with the
To clean the viewfinder lens
Remove dust from the viewfinder using a
blower brush.
cart, stand, tripod,
bracket, or table
specified by the
manufacturer, or
sold with the
apparatus.When a
cart is used, use
caution when
NOTES:
● Avoid using strong cleaning agents such as
benzine or alcohol.
● Cleaning should be done only after the battery
pack has been removed or other power units
have been disconnected.
● Mold may form if the lens is left dirty.
● When using a cleaner or chemically treated
cloth refer to the cautions of each product.
● To clean the viewfinder, please consult your
nearest JVC dealer.
moving the cart/
apparatus combination to avoid injury from tip-
over.
11. Unplug this apparatus during lightning storms
or when unused for long periods of time.
12. Refer all servicing to qualified service
personnel. Servicing is required when the
apparatus has been damaged in any way,
such as power-supply cord or plug is
damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does
not operate normally, or has been dropped.
USE CLEANING CASSETTE
Appears if dirt is detected on the heads during
recording. Use an optional cleaning cassette
(੬ pg. 3).
CONTENTS
GETTING STARTED
6
EN
Changing The Menu Settings...................... 31
Snapshot (Record Still Image On Tape) ..... 37
Manual White Balance Adjustment ............. 40
Connection To A Personal Computer ......... 44
RECORDING & PLAYBACK
VIDEO RECORDING ........................................18
Time Code...............................................20
Dual Rec..................................................20
VIDEO PLAYBACK ..........................................21
Blank Search...........................................22
Playback Snapshot..................................22
Connections To A TV Or VCR.....................23
Playback Using The Remote Control ..........24
46
SPECIFICATIONS ............................................51
TERMS ..........................................................52
D.S.C. RECORDING.........................................26
Basic Shooting (D.S.C. Snapshot) ..............26
D.S.C. PLAYBACK...........................................27
Normal Playback Of Images........................27
Auto Playback Of Images............................27
Index Playback Of Files...............................27
Removing On-Screen Display.....................27
ADDITIONAL FEATURES FOR D.S.C.
28
Resetting The File Name.............................28
Protecting Files............................................28
Deleting Files...............................................29
Setting Print Information (DPOF Setting)*...29
Initializing A Memory Card...........................30
GETTING STARTED
EN
7
Regarding This Manual
Provided Accessories
Control Lever
LCD Monitor
OR
AC Adapter AP-V14U or AP-V18U
OR
Control lever
Audio/Video Cable
(ø3.5 mini-plug to RCA plug)
BatteryPack
BN-VF808U
There are two kinds of operation using the control
lever: moving the lever towards up/down/left/right,
or pressing down the lever.
They are described and illustrated as shown
below.
1) Move the control lever up/down/left/right
(3/4/1/2) to select:
Select
CD-ROM
Remote
USB Cable
Control Unit
RM-V740U
Operation
To select
Move the control lever up.
3
4
6
7
FOCUS
Move the control lever
down.
Lithium
Battery
CR2025*
(for remote
control unit)
Shoulder
Lens Cap
(੬ pg. 12)
Strap
Move the control lever
right.
LIGHT
(੬ pg. 12)
2
1
¡
1
Move the control lever left.
QUICK
REVIEW
* A lithium battery is pre-installed in the Remote
Control Unit at time of shipment (with insulation
sheet).To use the Remote Control Unit, remove
the insulation sheet.
2) Press down the control lever to select SET:
SET
NOTES:
● In order to maintain optimum performance of the
camcorder, provided cables may be equipped
with one or more core filter. If a cable has only
one core filter, the end that is closest to the filter
should be connected to the camcorder.
● Make sure to use the provided cables for
connections. Do not use any other cables.
GETTING STARTED
8
EN
Index
89
o~)
36
27
28
29 30
31
34
! #" 24
25
5 6
7
$
33 32
%
20
21
1 4 3
2
(
&
26
22 35 23
How to open the LCD monitor
Pull on the end A of the LCD monitor.
NOTES:
● The image will not appear
simultaneously on the LCD monitor and
the viewfinder. When the viewfinder is
pulled out while the LCD monitor is
opened, you can select which one to
use. Set “PRIORITY” to the desired
mode in SYSTEM Menu. (੬ pg. 34)
● Colored bright spots may appear all over
the LCD monitor or the viewfinder.
However, this is not a malfunction.
The LCD monitor can rotate 270°.
Power-linked operation
When the power switch is set to “REC”, you can
also turn the camcorder on/off by opening/
closing the LCD monitor or pulling out/pushing in
the viewfinder.
GETTING STARTED
EN
9
Controls
Indicators
Quick Review [QUICK REVIEW] (੬ pg. 18)
2: Right/Fast-Forward (¡) (੬ pg. 21)/
LED Light [LIGHT] (੬ pg. 36)
Manual Focus [FOCUS] (੬ pg. 37)
4 : Down/Stop (7) (੬ pg. 21)/
Backlight Compensation [ ] (੬ pg. 39)/
Spot Exposure (੬ pg. 39)
LCD Monitor (੬ pg. 8)
Viewfinder (੬ pg. 15)
Card Cover [
Battery Pack Mount (੬ pg. 13)
Shoulder Strap Eyelet (੬ pg. 12)
Grip Strap (੬ pg. 12)
Lens
] (੬ pg. 17)
Press down : SET
2VIDEO/MEMORY Switch
Blank Search [BLANK] (੬ pg. 22)
Index Button [INDEX] (੬ pg. 27)
4Menu Button [MENU] (੬ pg. 31)
6Auto Button [AUTO] (੬ pg. 20)
7Diopter Adjustment Control (੬ pg. 15)
8Snapshot Button [SNAPSHOT]
(੬ pg. 26, 33, 37)
Live Slow Button [SLOW] (੬ pg. 33, 36)
9Power Zoom Lever [T/W] (੬ pg. 19)
Speaker Volume Control [VOL. +, –]
(੬ pg. 21)
LED Light (੬ pg. 36)
Camera Sensor
(Be careful not to cover this area, a sensor
necessary for shooting is built-in here.)
Remote Sensor (੬ pg. 24, 25)
Stereo Microphone
Tripod Mounting Socket (੬ pg. 15)
Cassette Holder Cover (੬ pg. 16)
Memory Card Slot
Connector Cover
!Recording Start/Stop Button [START/STOP]
(੬ pg. 18)
"Power Switch [REC, PLAY, OFF]
#Lock Button
$Battery Release Button [BATT.] (੬ pg. 13)
%Cassette Open/Eject Switch [OPEN/EJECT]
(੬ pg. 16)
REC:
To perform recording on the tape or in the
memory card.
OFF:
To switch off the camcorder.
PLAY:
Connectors
● To play back a recording on the tape.
● To display a still image stored in the
memory card or to transfer a still image
stored in the memory card to a PC.
&USB (Universal Serial Bus) Connector
(੬ pg. 44)
(Digital Video Connector [DV IN/OUT]
(i.LINK*) (੬ pg. 43, 44)
*
i.LINK refers to the IEEE1394-1995 industry
specification and extensions thereof. The
logo is used for products compliant with the
i.LINK standard.
The connectors are located beneath the
covers.
)Audio/Video Output Connector [AV]
(੬ pg. 23, 42)
~DC Input Connector [DC] (੬ pg. 13)
VIDEO/MEMORY Switch Position
VIDEO:
To record on a tape or play back a tape.
MEMORY:
To record in a memory card or access data
stored in a memory card.
GETTING STARTED
EN
10
During Both Video And D.S.C. Recording
LCD Monitor/Viewfinder
Indications
" #
$
9
!
1
2
3
4
5
6
7
8
During Video Recording Only
M
640F
%
&
15
PHOTO
2 3 4
5
1
3
(
LP
– – –min
16:9
7
W
H
9
11:13 AM
D
EC
.6.200
7
#
"
SOUND 12BIT
~
)
1Battery Remaining Power Indicator
15:55
!
: Manual Mode
1Tape Running Indicator
(Rotates while tape is running.)
3LED Light Indicator (੬ pg. 36)
4
: Night-Alive Indicator (੬ pg. 41)
2Selected Wide Mode Indicator (੬ pg. 17)
(only 16:9 indicator is displayed)
3Live Slow Indicator (੬ pg. 36)
4Recording Speed Mode (SP/LP) (੬ pg. 33)
(only LP indicator is displayed)
5Tape Remaining Time (੬ pg. 18)
6REC: (Appears during recording.)
(੬ pg. 18)
: Gain Up Mode (੬ pg. 33)
5Shutter Speed (੬ pg. 41)
7Selected Effect Indicator (੬ pg. 41)
9Approximate Zoom Ratio (੬ pg. 19)
!Zoom Indicator (੬ pg. 19)
"Shooting Icon
(Appears and blinks during shooting.)
#Card Icon (੬ pg. 26)
: Appears during shooting.
: Blinks in white when a memory card is
not loaded.
$Image Size/Picture Quality: 640F 640 x 480 F
640F (FINE) and 640 x 480 S 640S
(STANDARD) (in order of quality) (੬ pg. 33)
%Remaining Number Of Shots (੬ pg. 26)
(Displays the approximate remaining
number of shots that can be stored during
D.S.C. recording.)
SLOW: (Appears when using Live Slow.)
(੬ pg. 36)
: Insert (੬ pg. 45)
7
8
: Insert Pause
8Selected Wipe/Fader Effect Indicator
(੬ pg. 40)
9Wind Cut Indicator (੬ pg. 33)
!Time Code (੬ pg. 34)
"Digital Image Stabilizer (“DIS”) (੬ pg. 32)
(only
indicator is displayed)
#SOUND 12BIT/16BIT: Sound Mode
Indicator (੬ pg. 33) (Appears for approx. 5
seconds after turning on the camcorder.)
&
PHOTO: (Appears when taking Snapshot.)
(੬ pg. 26, 37)
(
: Spot Exposure Control Indicator
(੬ pg. 39)
: Backlight Compensation Indicator
(੬ pg. 39)
: Exposure Adjustment Indicator
(੬ pg. 38)
: Iris Lock Indicator (੬ pg. 38)
)Date/Time (੬ pg. 15)
~Manual Focus Adjustment Indicator
(੬ pg. 37)
GETTING STARTED
EN
11
During Video Playback
1
2
3 4
5 6
1
2
LP
x3
100-0013
12B I T / M I X
L
3
BLANK SEARCH
PUSH "STOP" BUTTON
TO CANCEL
11:13 AM
4
DEC. 6. 2007
VOLUME
11
.
:
6
13 AM
200
1Battery Remaining Power Indicator
2Folder/File Number
20 : 21 : 25
DE C
.
7
4Date/Time
9
7
8
2Sound L/R Indicator (੬ pg. 35)
3Blank Search Indicator (੬ pg. 22)
4Tape Speed (SP/LP) (੬ pg. 35)
(only LP indicator is displayed)
5Variable Search Speed Indicator: x-10, x-3,
x3 and x10 (੬ pg. 22)
63: Playback
¡: Fast-Forward/Shuttle Search
1: Rewind/Shuttle Search
8: Pause
8 3: Forward Frame-By-Frame Playback/
Slow-Motion
2 8: Reverse Frame-By-Frame Playback/
Slow-Motion
: Audio Dubbing
: Audio Dubbing Pause
7Date/Time (੬ pg. 35)
8VOLUME: Volume Level Indicator
(੬ pg. 21)
8
9Time Code (੬ pg. 35)
GETTING STARTED
EN
12
How To Attach The Lens Cap
Grip Adjustment
Open the pad and make grip adjustments.
● Before making the adjustment, remove any
security tags that may be attached to the
velcro.
To protect the lens, attach
the provided lens cap to the
camcorder as shown in the
illustration.
NOTE:
To confirm the lens cap is on
correctly make sure the cap is
flush to the camcorder.
Place here during
shooting.
How To Attach The Shoulder Strap
1 Peel off the pad
and thread the end
of the strap
through the eyelet.
Eyelet
2 Thread the
Strap Guide
strap through the
Buckle
buckle, adjust its
length, and use the
strap guide to fix it
in place.
3 Position the
buckle near the
eyelet and reattach
the pad.
GETTING STARTED
EN
13
NOTES:
Power
Charging The Battery Pack
● If the protective cap is attached to the battery
pack, remove it first.
● During charging, the camcorder cannot be
operated.
POWER/CHARGE Lamp
● Charging is not possible if the wrong type of
battery is used.
● When charging the battery pack for the first time
or after a long storage period, the POWER/
CHARGE lamp may not light. In this case,
remove the battery pack from the camcorder,
then try charging again.
Battery pack
mount
Arrow
2
● If a fully charged battery pack is attached to the
unit, POWER/CHARGE lamp will blink for
approx. 10 seconds before it turns off.
● If the battery operation time remains extremely
short even after having been fully charged, the
battery is worn out and needs to be replaced.
Please purchase a new one.
1
Battery
pack
BATT.
Power Switch
To DC connector
● Since the AC Adapter processes electricity
internally, it becomes warm during use. Be sure
to use it only in well-ventilated areas.
● After 5 minutes have elapsed in Record-
Standby mode with the cassette inserted and no
operation is performed, the camcorder will
automatically turn off its power supplied from the
AC adapter. In this case, the battery charge
starts if the battery is attached to the camcorder.
Lock
Button
AC Adapter
To AC outlet
About Batteries
1 Set the Power Switch to “OFF”.
DANGER! Do not attempt to take the batteries
apart, or expose them to flame or excessive
heat, as it may cause a fire or explosion.
WARNING! Do not allow the battery or its
terminals to come in contact with metals, as
this can result in a short circuit and possibly
start a fire.
2 With the arrow on the battery pack pointing
upward, push the battery pack slightly against
the battery pack mount 1.
3 Slide up the battery pack until it locks in
place 2.
4 Plug the AC Adapter into an AC outlet.
5 Connect the AC Adapter to the camcorder.
● The POWER/CHARGE lamp on the camcorder
blinks to indicate charging has started.
● When the POWER/CHARGE lamp goes out,
charging is finished. Unplug the AC Adapter
from the AC outlet. Disconnect the AC Adapter
from the camcorder.
To restore the accuracy of the battery
power indicator
If the battery power indication differs from the
actual operating time, fully charge the battery,
and then run it down. However this method
may not work if the battery was used for a long
period of time under extremely high/low
temperature condition or charged too many
times.
To detach the battery pack
Slide the battery pack downward while
pressing BATT. to detach it.
Battery pack
BN-VF808U*
Charging time
Approx. 1 hr. 30 min.
Approx. 2 hrs. 40 min.
Approx. 3 hrs. 50 min.
BN-VF815U
BN-VF823U
* Provided
GETTING STARTED
EN
14
● If “COMMUNICATION ERROR” appears
instead of the battery status even though you
tried to press DATA several times, there may
be a problem with your battery. In such a
case, consult your nearest JVC dealer.
Using The Battery Pack
Perform steps 2 – 3 in “Charging The Battery
Pack” (੬ pg. 13).
Maximum continuous recording time
Using AC Power
Perform step 4 – 5 in “Charging The Battery
Pack” (੬ pg. 13).
LCD monitor
Battery pack
Viewfinder on
on
BN-VF808U*
BN-VF815U
BN-VF823U
* Provided
NOTES:
1 hr. 50 min.
3 hrs. 40 min.
5 hrs. 30 min.
2 hrs. 15 min.
4 hrs. 30 min.
6 hrs. 45 min.
NOTE:
The provided AC Adapter features automatic
voltage selection in the AC range from 110 V to
240 V.
INFORMATION:
● Recording time is reduced significantly under
the following conditions:
• Zoom or Record-Standby mode is engaged
The following explanations in this manual
supposes the use of LCD monitor in your
operation. If you want to use the viewfinder,
close the LCD monitor and pull out the
viewfinder fully.
repeatedly.
• The LCD monitor is used repeatedly.
• The playback mode is engaged repeatedly.
• The LED Light is used.
● Before extended use, it is recommended that
you prepare enough battery packs to cover
3 times the planned shooting time.
Language Settings
The language on the display can be changed.
(੬ pg. 34)
ATTENTION:
Select
Before detaching the power source, make sure
that the camcorder’s power is turned off. Failure to
do so can result in a camcorder malfunction.
LANGUAGE
Data Battery System
ENGLISH
You can check the remaining battery power
and the recordable time.
SET
When the battery is attached, press DATA.
1 Open the LCD monitor fully.
BATTERY CONDITION
2 Set the Power Switch to “REC” or “PLAY”
while pressing down the Lock Button located
on the switch.
MAX TIME
100%
LCD
min
min
50%
0%
● If set to “REC”, the recording mode should be
set to “ ” (੬ pg. 20).
FINDER
3 Press MENU.
● When the Power Switch is set to “OFF”, it is
displayed for approx. 3 seconds if the button
is pressed and released quickly, and for
approx. 15 seconds if the button is pressed
and hold for several seconds.
● When the Power Switch is set to “PLAY” or
“REC”, press DATA again to return to the
normal screen.
4 Select “SYSTEM”, press SET or 2.
5 Select “LANGUAGE”, press SET or 2.
6 Select the desired language, press SET or
2.
7 Press MENU.
Press 1whenever you want to return to the
previous menu screen.
● Data battery status cannot be displayed
during playback or while recording is in
progress.
GETTING STARTED
EN
15
Date/Time Settings
Brightness Adjustment Of The
Display
Select
CLOCK ADJ.
MONTH. DATE. YEAR 12
h
Select
JAN. 03
02
.
2007
:
10 AM
BRIGHT
0
SET
The date/time is recorded onto the tape at all
times, but its display can be turned on or off.
(੬ pg. 34, 35)
Perform steps 1 – 3 in “Language Settings”
(੬ pg. 14).
SET
Perform steps 1 – 3 in “Language Settings”
(੬ pg. 14).
● To adjust the brightness of the viewfinder,
pull out the viewfinder fully and set
“PRIORITY” to “FINDER” (੬ pg. 34).
1 Select “DISPLAY”, press SET or 2.
2 Select “CLOCK ADJ.”, press SET or 2.
1 Select “DISPLAY”, press SET or 2.
3 Select the desired date display format,
2 Select “BRIGHT”, press SET or 2.
press SET or 2.
● Repeat this step to input time display format
(Select from “24h” or “12h”), month, date, year,
hour and minutes.
3 Select the appropriate brightness, press
SET or 2.
4 Press MENU.
Press 1whenever you want to return to the
previous menu screen.
4 Press MENU.
Press 1whenever you want to return to the
previous menu screen/setting.
Tripod Mounting
To attach the
Viewfinder Adjustment
1 Set the Power Switch to “REC” while
pressing down the Lock Button located on the
switch.
camcorder to a tripod,
align the direction stud
and screw to the
mounting socket and
stud hole on the
camcorder. Then
tighten the screw
clockwise.
2 Make sure the LCD monitor is closed and
locked. Pull out the viewfinder fully.
3 Turn the Diopter Adjustment Control until
the indications in the viewfinder are clearly
focused.
Example:
● Some tripods are not
equipped with studs.
Diopter Adjustment Control
CAUTION:
When retracting the viewfinder, take care not to
pinch your fingers.
GETTING STARTED
EN
16
● When the camcorder is suddenly moved from a
cold place to a warm environment, wait a short
time before opening the cassette holder cover.
Loading/Unloading A Cassette
The camcorder needs to be powered up to
load or eject a cassette.
• Appears if a tape is loaded while the Power
Switch is set to “REC”.
• Blinks when no tape is loaded.
PUSH
Cassette
holder
cover
TAPE!
Appears if a tape is not loaded when the
Recording Start/Stop Button or SNAPSHOT
Button is pressed while the Power Switch is set to
“REC” and the VIDEO/MEMORY Switch is set to
“VIDEO”.
Erase
OPEN/
EJECT
CHECK TAPE’S ERASE PROTECTION TAB
protection
tab
Cassette holder
Appears when the erase protection tab is set to
“SAVE” while the Power Switch is set to “REC”
and the VIDEO/MEMORY Switch is set to
“VIDEO”. (੬ pg. 18)
Make sure the window
side is facing out.
1 Slide and hold OPEN/EJECT in the
direction of the arrow, then pull the cassette
holder cover open until it locks. The cassette
holder opens automatically.
● Do not touch internal components.
2 Insert or remove a tape and press “PUSH”
to close the cassette holder.
● Be sure to press only the section labeled
“PUSH” to close the cassette holder; touching
other parts may cause your finger to get caught
in the cassette holder, resulting in injury or
product damage.
● Once the cassette holder is closed, it recedes
automatically. Wait until it recedes completely
before closing the cassette holder cover.
● When the battery pack’s charge is low, you may
not be able to close the cassette holder cover.
Do not apply force. Replace the battery pack
with a fully charged one or use AC power before
continuing.
3 Close the cassette holder cover firmly until
it locks into place.
NOTES:
● If you wait a few seconds and the cassette
holder does not open, close the cassette holder
cover and try again. If the cassette holder still
does not open, turn the camcorder off then on
again.
● If the tape does not load properly, open the
cassette holder cover fully and remove the
cassette. A few minutes later, insert it again.
GETTING STARTED
EN
17
Loading/Unloading A Memory
Card
16:9 Wide Mode
You can record videos at 4:3 size and 16:9
size. By default, the camera is set to record
videos at the 16:9 size.
Card Cover (
)
Memory card
(Optional)
Clipped edge
1 Make sure the camcorder’s power is off.
).
16:9
2 Open the card cover (
3 To load a memory card, firmly insert it with
its clipped edge first.
To unload a memory card, push it once.
After the memory card comes out of the
camcorder, pull it out.
● Do not touch the terminal on the reverse
side of the label.
2 Set the VIDEO/MEMORY Switch to
“VIDEO”. Each press 16:9 switches the screen
size.
On the LCD monitor:
4 Close the card cover.
NOTES:
16 : 9
4 : 3
4 : 3
● Some brands of memory cards are not
compatible with this camcorder. Before
purchasing a memory card, consult its
manufacturer or dealer.
● Before using a new memory card, it is
necessary to format the card. (੬ pg. 30)
On the viewfinder:
16 : 9
PLEASE FORMAT
Appears when there is a problem with a memory
card and its memory is corrupt, or it has not been
initialized. Initialize the memory card. (੬ pg. 30)
NOTE:
If you record videos in 16:9 size, the image may
appear to be slightly vertically stretched when
playing back on TV with the 4:3 screen.
(੬ pg. 34, 35)
CARD ERROR!
Appears when the camcorder does not recognize
the loaded memory card. Remove the memory
card once and insert it again. Repeat these
procedures until no indication appears. If the
indication still appears, the memory card is
corrupted.
VIDEO RECORDING
EN
18
● When a blank portion is left between recorded
scenes on the tape, the time code is interrupted
and errors may occur when editing the tape. To
avoid this, refer to “Recording From The Middle
Of A Tape” (੬ pg. 20).
Basic Recording
NOTE:
Before continuing, perform the procedures listed
below:
● To record in LP (Long Play) mode, ੬ pg. 33.
● Power (੬ pg. 13)
Tape Remaining Time
Approximate tape
remaining time appears on
the display. “– – – min”
● Loading A Cassette (੬ pg. 16)
● Remove the lens cap. (੬ pg. 12)
● Open the LCD monitor fully.
● Select videos at 4:3 size or 16:9 (wide) size.
(੬ pg. 17)
means the camcorder is
calculating the remaining
VIDEO/MEMORY
time. When the remaining time reaches
2 minutes, the indication starts blinking.
● The time required to calculate and display the
remaining tape length, and the accuracy of the
calculation, may vary according to the type of
tape used.
Zoom Lever
Quick Review
Enables to check the end of the last recording.
1) Press QUICK REVIEW during
the Recording-Standby mode.
Lock Button
Recording Start/Stop
Button
2) Tape is rewound for about
several seconds and played back
automatically, then pauses in the
Recording-Standby mode for the next shot.
● Distortion may occur at start of playback. This is
normal.
1 Set the VIDEO/MEMORY Switch to
“VIDEO”.
2 Set the Power Switch to “REC” while
pressing down the Lock Button located on the
switch.
● Slide the Power Zoom lever repeatedly to
change the sound setting to on/off.
3 Press START/STOP button to start
recording. “REC” appears on the display while
recording is in progress. To stop recording
Press START/STOP again.
Approximate recording time
Recording mode
Tape
SP
LP
45 min.
30 min.
60 min.
80 min.
30 min.
60 min.
80 min.
90 min.
120 min.
NOTES:
● If the Record-Standby mode continues for
5 minutes and no operation is performed, the
camcorder’s power shuts off automatically. To
turn the camcorder on again, push back and pull
out the viewfinder again or close and re-open
the LCD monitor.
VIDEO RECORDING
EN
19
Zooming
Interface Shooting
While recording
The person you shoot
can view himself/
Zoom out
Zoom in
herself in the LCD
monitor, and you can
even shoot yourself
while viewing your
own image in the
LCD monitor.
1) Open the LCD
W: Wide angle
● You can zoom in up to 34X by using the optical
zoom.
T: Telephoto
● Zoom magnification over 34X is done through
digital image processing, and is therefore called
digital zoom. Digital zooming is possible up to
900X. Set (ZOOM) to [68X] or [900X].
(੬ pg. 32)
monitor and tilt it
upward to 180° so
that it faces forward.
Then, pull out the
viewfinder fully.
2) Point the lens
Optical zoom (up to 34X)
toward the subject (yourself when self-
recording) and start recording.
● During Interface Shooting, the monitor image
appears inverted as it would when viewing a
mirror. However, the actual recorded image
does not appear inverted.
Digital zoom (up to 900X)
● If the Quick Review (੬ pg. 18) is executed
during the interface shooting, the LCD monitor
will be turned off. In such a case, check the
playback picture in the viewfinder.
● To check the playback picture in the LCD
monitor, close the viewfinder.
NOTES:
● Macro shooting is possible as close as approx. 5
cm (2") to the subject when the zoom lever is set
all the way to W.
● When you zoom into a subject close to the lens,
the camera may automatically zoom out
depending on the distance to the subject. In this
case, set “TELE MACRO” to “ON”. (੬ pg. 32)
Journalistic Shooting
In some situations,
different shooting
angles may provide
more dramatic
results. Hold the
camcorder in the
desired position and
tilt the LCD monitor
in the most
convenient direction.
It can rotate 270°
(90° downward, 180°
upward).
VIDEO RECORDING
EN
20
Time Code
Recording From The Middle Of A Tape
During recording, a time code is recorded on
1) Play back a tape or use Blank Search
the tape.This code is to confirm the location of (੬ pg. 22) to find the spot at which you want to
the recorded scene on the tape during
playback.
start recording, then engage the Still Playback
mode. (੬ pg. 21)
2) Set the Power Switch to “REC” while
pressing down the Lock Button located on the
Display
Minutes
Seconds
Dual Rec.
Frames*
You can capture still images without disturbing
the recording in progress. Press SNAPSHOT.
A sub screen will be displayed for approx. 6
seconds to show you the snapshot image.
● The Still image is saved into the memory card
while video is recorded onto the cassette tape.
(30 frames =
12 : 34 : 24
1 second)
* Frames are not displayed during recording.
If recording starts from a blank portion, the
time code begins counting from “00:00:00”
(minute:second:frame). If recording starts from
the end of a previously recorded scene, the
time code continues from the last time code
number. If during recording a blank portion is
left partway through the tape, the time code is
interrupted. When recording is resumed, the
time code starts counting up again from
“00:00:00”. This means the camcorder may
record the same time codes as those existing
in a previously recorded scene.To prevent this,
perform Recording From The Middle Of A Tape
(੬ pg. 20) in the following cases;
● “REC SELECT” must be set to “
only.
(CARD)”
Auto/Manual Mode
Press AUTO button repeatedly to switch to
auto/manual recording mode. When manual
mode is selected, the indicator“ ” appears on
the LCD monitor.
Auto Mode :
You can record using no special effects or
manual adjustments.
● When shooting again after playing back a
recorded tape.
● When power shuts off during shooting.
● When a tape is removed and re-inserted during
shooting.
Manual Mode :
Manual recording is possible by setting various
functions.
● When shooting using a partially recorded tape.
● When shooting on a blank portion located
partway through the tape.
AUTO
MANUAL
● When shooting again after shooting a scene
then opening/closing the cassette holder cover.
NOTES:
● The time code cannot be reset.
● During fast-forwarding and rewinding, the time
code indication does not move smoothly.
● The time code is displayed only when “TIME
CODE” is set to “ON”. (੬ pg. 34)
VIDEO PLAYBACK
EN
21
NOTES:
Normal Playback
● The playback picture can be viewed in the LCD
monitor, viewfinder or on a connected TV.
(੬ pg. 23)
VOL. +/–
VIDEO/
MEMORY
BLANK
Lock Button
● If Stop mode continues for 5 minutes when
power is supplied from a battery, the camcorder
shuts off automatically.To turn the camcorder on
again, push back and pull out the viewfinder
again or close and re-open the LCD monitor.
● When a cable is connected to the AV connector,
the sound is not heard from the speaker.
6
¡
Power
Switch
1
MENU
HDV
7
Speaker
Appears when pictures recorded in the HDV
format are detected. The pictures in the HDV
format cannot be played back with this
camcorder.
1 Load a cassette. (੬ pg. 16)
2 Set the VIDEO/MEMORY Switch to
“VIDEO”.
Still Playback
3 Set the Power Switch to “PLAY” while
pressing down the Lock Button located on the
switch.
Pauses during video playback.
1) Press 6 during playback.
2) To resume normal playback, press 6
again.
● If still playback continues for more than about
3 minutes, the camcorder’s Stop mode is
automatically engaged.
SET
● The above screen (referring to the control lever
(੬ pg. 7)) will be displayed for approx. 3
seconds on the LCD Monitor.
Operation
6
7
¡
To select
Move the control lever up.
Move the control lever down.
Move the control lever right.
Move the control lever left.
1
4 To start playback, press 6.
5 To stop playback, press 7.
● During Stop mode, press 1 to rewind, or ¡
to fast-forward the tape.
● Press SET to display the guide operation
screen.
To control the speaker volume
Slide the Power Zoom Lever (VOL. +/–)
towards “+” to turn up the volume, or towards
“–” to turn down the volume.
VIDEO PLAYBACK
EN
22
Variable Shuttle Search
Blank Search
Allows variable-speed search in either
direction during video playback.
Helps you find where you should start
recording in the middle of a tape to avoid time
1) During playback, press ¡ once or twice for code interruption. (੬ pg. 20)
forward search, or 1 once or twice for
1 Perform steps 1 – 3 in “Normal Playback”
reverse search.
(੬ pg. 21).
1
¡
2 Press BLANK.
x-10
x-3
x3
x10
● The “BLANK SEARCH” indication appears and
the camcorder automatically starts reverse or
forward search, then stops at the spot which is
about 3 seconds of tape before the beginning of
the detected blank portion.
2) To resume normal playback, press 6.
● During playback, press and hold ¡ or 1.
The search continues as long as you hold the
button. Once you release the button, normal
playback resumes.
● A slight mosaic effect appears on the display
during Shuttle Search. This is not a malfunction.
● To cancel Blank Search, press 7 or BLANK.
NOTES:
● Before starting Blank Search, if the current
position is at a blank portion, the camcorder
searches in the reverse direction. If the current
position is at a recorded portion, the camcorder
searches in the forward direction.
ATTENTION:
During Shuttle Search,
parts of the picture may not
be clearly visible,
● If the beginning or end of the tape is reached
during Blank Search, the camcorder stops
automatically.
particularly on the left side
of the screen.
● A blank portion which is shorter than 5 seconds
of tape may not be detected.
● The detected blank portion may be located
between recorded scenes. Before you start
recording, make sure there is no recorded
scene after the blank portion.
During Shuttle Search,
parts of the picture may not
be clearly visible across
the screen.
Playback Snapshot
This camcorder allows you to take snapshots
during video playback.
Press SNAPSHOT.
VIDEO PLAYBACK
EN
23
1 Make sure all units are turned off.
Connections To A TV Or VCR
2 Connect the camcorder to a TV or VCR as
shown in the illustration.
If using a VCR, go to step 3.
If not, go to step 4.
3 Connect the VCR output to the TV input,
referring to your VCR’s instruction manual.
To AV
connector
5 Set the VCR to its AUX input mode, and set
the TV to its VIDEO mode.
or
6 Start playback on the camcorder.
(੬ pg. 21)
● Please set “16:9 OUTPUT” of Playback Menus
so that the image may suit your TV (16:9 TV or
4:3 TV). (੬ pg. 34, 35)
Audio/Video cable
(provided)
To choose whether or not the following
displays appear on the connected TV
● Date/Time
Set “DATE/TIME” to “ON” or “OFF” (੬ pg. 35).
Or, press DISPLAY on the remote control to turn
on/off the date indication.
● Time Code
TV
Set “TIME CODE” to “ON” or “OFF” (੬ pg. 35).
● Indications other than date/time and time code
Set “ON SCREEN” to “OFF”, “LCD” or “LCD/TV”
(੬ pg. 35).
VCR
NOTES:
1Yellow to VIDEO IN (Connect when your TV/
VCR has only A/V input connectors.)
2Red to AUDIO R IN*
3White to AUDIO L IN*
* Not required for watching still images only.
● It is recommended to use the AC Adapter as
the power supply instead of the battery
pack. (੬ pg. 13)
● To monitor the picture and sound from the
camcorder without inserting a tape or memory
card, set the camcorder’s Power Switch
to“REC”, then set your TV to the appropriate
input mode.
● Make sure you adjust the TV sound volume to its
minimum level to avoid a sudden burst of sound
when the camcorder is turned on.
VIDEO PLAYBACK
EN
24
Buttons And Functions
Playback Using The Remote
Control
A battery is included inside the remote control
at the time of purchase.
Remove the insulation sheet before use.
Installing The Battery
The remote control uses one lithium battery
(CR2025).
Pull out the battery
holder by pressing the
lock tab.
1Infrared beam transmitting window
The following buttons are available only when
the camcorder’s Power Switch is set to “PLAY”.
2PAUSE Button
Lock tab
Up Button (੬ pg. 25)
3SLOW Rewind Button (੬ pg. 25)
4REW Button
Beam Effective Area (indoor use)
Left Button (੬ pg. 25)
When using the
5INSERT Button (੬ pg. 45)
6SHIFT Button (੬ pg. 25)
7DISPLAY Button (੬ pg. 23, 42)
8SLOW Forward Button (੬ pg. 25)
9PLAY Button
!FF Button
Right Button (੬ pg. 25)
"A. DUB Button (੬ pg. 45)
#STOP Button
Down Button (੬ pg. 25)
$EFFECT Button (੬ pg. 25)
%EFFECT ON/OFF Button (੬ pg. 25)
remote control, be
sure to point it at the
remote sensor. The
transmitted beam’s
approximate effective
distance for indoor
use is 5m (16ft).
Remote sensor
NOTE:
The transmitted beam may not be effective or may
cause incorrect operation when the remote sensor
is directly exposed to sunlight or powerful lighting.
The following buttons are available when the
camcorder’s Power Switch is set to “REC”.
&Zoom (T/W) Buttons
Zoom in/out (੬ pg. 19, 25)
(Also available with the Power Switch set to
“PLAY”)
(START/STOP Button
Functions the same as the Recording Start/
Stop Button on the camcorder.
)S.SHOT Button
Functions the same as SNAPSHOT on the
camcorder.
(Also available with the Power Switch set to
“PLAY”)
VIDEO PLAYBACK
EN
25
.
1) Press PLAY (3) to start
video playback. Or perform
normal playback of images.
Zoom (T/W)
SLOW (
PAUSE or
(Up)
SLOW (
(Right)
)
2) At the point you want to
zoom in, press the Zoom
Button (T).
● To zoom out, press the Zoom
Button (W).
)
PLAY
(Left)
STOP or
SHIFT
(Down)
3) You can move the image on
the screen around to find a
particular portion of the picture.
While holding down SHIFT,
press
(Up) and
(Left), (Right),
(Down).
Slow-Motion Playback
● To end zoom, press and hold W until
magnification returns to normal. Or, press STOP
(7) and then press PLAY (3) during video
playback.
● To end zoom during D.S.C. playback, press
PLAY (3).
During normal video playback, press SLOW
(
or ) more than approx. 2 seconds.
● After approx. 10 minutes, normal playback
resumes.
● To pause Slow-Motion playback, press PAUSE
(PAUSE).
NOTES:
● To revert back to normal playback, press PLAY
(3).
● Zoom can also be used during slow-motion and
still playback.
● Due to digital image processing, the quality of
the image may suffer.
NOTES:
● You can also engage Slow-Motion Playback
from Still Playback by pressing SLOW (
) more than approx. 2 seconds.
or
Playback Special Effects
● After SLOW (
or
) is pressed and held, the
Allows you to add creative effects to the video
playback image.
still image may be displayed for a few seconds,
followed by a blue screen for a few seconds.
This is not a malfunction.
SEPIA (੬ pg. 41).
MONOTONE (੬ pg. 41).
CLASSIC (੬ pg. 41).
STROBE (੬ pg. 41).
● During Slow-Motion Playback, there will be
disturbances in video and the picture may seem
unstable, especially with steady images. This is
not a malfunction.
1) To start
playback,
press PLAY
(3).
EFFECT ON/OFF
EFFECT
Frame-By-Frame Playback
During normal or still playback, press SLOW
(
) repeatedly for forward or SLOW (
)
2) Press
EFFECT.
The
repeatedly for reverse. Each time SLOW (
or ) is pressed, the frame is played back.
PLAYBACK EFFECT Select Menu appears.
3) Press EFFECT repeatedly to move the
highlight bar to the desired effect.
● The selected function is activated and after
2 seconds the menu disappears.
● To deactivate the selected effect, press EFFECT
ON/OFF. To reactivate the selected effect press
EFFECT ON/OFF again.
Playback Zoom
Magnifies the recorded image up to 27X at any
time during video playback and D.S.C.
playback.
● To change the selected effect, repeat from step
2 above.
D.S.C. RECORDING
EN
26
Approximate Number of Storable Images
● The number increases or decreases depending
on the Picture Quality/Image Size, etc.
Basic Shooting (D.S.C. Snapshot)
You can use your camcorder as a Digital Still
Camera for taking snapshots. Still images are
stored in the memory card.
SD Memory Card
Image Size/Picture
Quality
8 MB 16 MB 32 MB 64 MB
640 x 480/FINE
47
95 205 425
NOTE:
Before continuing, perform the procedures listed
below:
640 x 480/STANDARD 160 295 625 1285
● Power (੬ pg. 13)
● Loading a Memory Card (੬ pg. 17)
● Remove the lens cap.
Image Size/Picture
Quality
8 MB 16 MB 32 MB
● Open the LCD monitor fully. (੬ pg. 8)
640 x 480/FINE
55
105
320
215
645
SNAPSHOT
190
VIDEO
Lock Button
MEMORY
VIDEO/
MEMORY
Power Switch
1 Set the VIDEO/MEMORY Switch to
“MEMORY”.
2 Set the Power Switch to “REC” while
pressing down the Lock Button located on the
switch.
● To change the Picture Quality, ੬ pg. 31, 33.
3 Press SNAPSHOT. The “PHOTO” indication
appears while the snapshot is being taken.
● To delete unwanted still images, refer to
“Deleting Files” (੬ pg. 29).
● When you do not want to hear the shutter
sound, set “MELODY” to “OFF”(੬ pg. 34).
NOTE:
If shooting is not performed for approx. 5 minutes
when the Power Switch is set to “REC” and power
is supplied from the battery pack, the camcorder
shuts off automatically to save power. To perform
shooting again, push back and pull out the
viewfinder again or close and re-open the LCD
monitor.
CHECK CARD’S WRITE PROTECTION
SWITCH
Appears when you attempt to shoot digital still
images when the write protection tab on the SD
Memory Card is set to the “LOCK” position.
MEMORY CARD!
Appears if there is no memory card loaded when
the SNAPSHOT Button is pressed.
D.S.C. PLAYBACK
EN
27
Normal Playback Of Images
Auto Playback Of Images
Images shot with the camcorder are
You can run through all the images stored in
memory card automatically.
automatically numbered, then stored in
numerical order in the memory card.You can
view the stored images, one at a time, much
like flipping through a photo album.
1 Perform steps 1 – 3 in “Normal Playback Of
Images” (੬ pg. 27).
● If you press 1during Auto Playback, files are
displayed in descending order.
VIDEO/MEMORY
● If you press 2during Auto Playback, files are
displayed in ascending order.
Lock Button
3 To end Auto Playback, press 7.
Index Playback Of Files
You can view several different files stored in
the memory card at a time. This browsing
capability makes it easy to locate a particular
file you want.
Power
Switch
3
4
2
[PLAY] 3,
1 Perform steps 1 – 3 in “Normal Playback Of
1
Images” (੬ pg. 27).
2 Press INDEX. The
SET
Selected file
[STOP] 7, MENU INDEX
Index Screen appears.
3
1
4
7
2
5
8
3 Press 4, 3, 1or 2
to move the frame to
the desired file.
1 Load a memory card. (੬ pg. 17)
6
9
2 Set the VIDEO/MEMORY Switch to
4 Press SET. The
selected file is
displayed.
“MEMORY”.
3 Set the Power Switch to “PLAY” while
pressing down the Lock Button located on the
switch.
Index number
● A stored image is displayed.
Removing On-Screen Display
1 Perform steps 1 – 3 in “Normal Playback Of
4 Press 1to display the previous file. Press 2
to display the next file.
Images” (੬ pg. 27).
NOTE:
Images shot and stored on the card with another
device with resolutions other than “640 x 480” will
be displayed as thumbnails only. These thumbnail
images cannot be transferred to a PC.
2 Press MENU.
Select
3 Select “ON SCREEN”, press
SET or 2. The ON SCREEN
menu appears.
● Press 1whenever you want to
return to the previous menu
Playback Zoom
Available only with the remote control.
SET
screen.
(੬ pg. 25)
4 Select “OFF”,
ON SCREEN
OFF
press SET or 2.
NO IMAGES STORED
ON
5 Press MENU.
● The operation
mode indicator,
folder/file number,
date/time and
battery remaining
power indicator, disappear.
● To display the indicators again, select “ON”.
Appears if there are no image files stored in the
memory card when you attempt memory card
playback.
?
Appears when playing back a file that is not
compatible with DCF or a file with a size that is not
compatible with this camcorder.
ADDITIONAL FEATURES FOR D.S.C.
EN
28
6 Select “EXECUTE”,
Resetting The File Name
PROTECT
PROTECT ?
press SET.
By resetting the file name, a new folder will be
made.The new files you are going to make will
be stored in the new folder. It is convenient to
separate the new files from previously made
files.
● To cancel protection,
select “RETURN”.
EXECUTE
RETURN
● Repeat steps 5 and 6
for all files you want to protect.
To protect all files stored in the memory
card
1 Perform steps 1 – 3 in “Normal Playback Of
Images” (੬ pg. 27).
4 Select “PROT.ALL”, press SET or 2. The
2 Press MENU.
Select
3 Select “NO.RESET”, press
SET or 2. The NO. RESET
screen appears.
● To cancel protection, select “RETURN”.
NOTE:
4 Select “EXECUTE”, press
If the “
” mark appears, the currently displayed
SET. The new folder (such as
SET
file is protected.
“101JVCGR”) will be made and
To Remove Protection
Before doing the following, perform steps 1 – 3
in “Protecting Files”.
the file name of the next shot starts from
DVC00001.
NOTE:
If the file name reaches DVC09999, a new folder
(such as “101JVCGR”) will be made and the file
name will start again from DVC00001.
To remove protection from the currently
displayed file
4 Select “CURRENT”, press SET or 2. The
PROTECT screen appears.
Protecting Files
The Protect mode helps prevent the accidental
erasure of files.
5 Press 1or 2to select the desired file.
6 Select “EXECUTE”, press SET.
● To cancel selection, select “RETURN”.
● Repeat steps 5 and 6 for all files you want to
remove protection.
1 Perform steps 1 – 3 in “Normal Playback Of
Images” (੬ pg. 27).
2 Press MENU.
To remove protection from all files stored in
the memory card
3 Select “PROTECT”, press SET or 2. The
PROTECT menu appears.
● Press 1whenever you want to return to the
previous menu screen.
4 Select “CANC.ALL”, press SET or 2. The
PROTECT screen appears.
5 Select “EXECUTE”, press SET.
To protect the currently displayed file
● To cancel selection, select “RETURN”.
4 Select “CURRENT”,
PROTECT
press SET or 2. The
PROTECT screen
appears.
CURRENT
PROT.ALL
CANC.ALL
5 Press 1or 2to select
the desired file.
Select
ADDITIONAL FEATURES FOR D.S.C.
EN
29
Deleting Files
Setting Print Information (DPOF
Setting)*
This camcorder is compatible with the DPOF
(Digital Print Order Format) standard in order
to support future systems such as automatic
printing.
Previously stored files can be deleted either
one at a time or all at once.
1 Perform steps 1 – 3 in “Normal Playback Of
Images” (੬ pg. 27).
2 Press MENU.
Select
* Up to a maximum limit of 999 stored files in the
memory card.
3 Select “DELETE”, press SET
or 2. The DELETE Menu
appears.
To Print All Still Images (One Print For
Each)
● Press 1whenever you want to
return to the previous menu
screen.
SET
Images” (੬ pg. 27).
To delete the currently displayed file
2 Press MENU.
4 Select “CURRENT”,
Select
DELETE
CURRENT
ALL
press SET or 2. The
DELETE screen
appears.
SET
5 Press 1or 2to select
3 Select “DPOF”, press
DPOF
CURRENT
ALL 1
the desired file.
SET or 2. The DPOF
Menu appears.
RESET
want to return to the
previous menu screen.
Select
6 Select “EXECUTE”,
press SET.
DELETE
4 Select “ALL 1”, press
DELETE?
● To cancel deletion,
select “RETURN”.
● Repeat steps 5 and 6
SET or 2. The DPOF screen appears.
EXECUTE
RETURN
5 Select “EXECUTE”,
DPOF
press SET.
ALL 1?
for all files you want to delete.
● To cancel selection,
EXECUTE
RETURN
select “RETURN”.
NOTE:
If the “
” mark appears, the selected file is
protected and cannot be deleted.
To delete all files stored in the memory card
4 Select “ALL”, press SET or 2. The DELETE
screen appears.
5 Select “EXECUTE”, press SET.
● To cancel deletion, select “RETURN”.
NOTES:
● Protected files (੬ pg. 28) cannot be deleted. To
delete them, remove protection first.
● Once files are deleted, they cannot be restored.
Check files before deleting.
ADDITIONAL FEATURES FOR D.S.C.
EN
30
To Print By Selecting Still Images And
Number Of Prints
To Reset The Number Of Prints
1 Perform steps 1 – 3 in “To Print All Still
Images (One Print For Each)” (੬ pg. 29).
1 Perform steps 1 – 3 in “To Print All Still
2 Select “RESET”, press SET or 2. The
Images (One Print For Each)” (੬ pg. 29).
DPOF screen appears.
2 Select “CURRENT”,
DPOF
● To cancel selection, select “RETURN”.
● The number of prints is reset to 0 for all still
images.
press SET or 2. The DPOF
SHEETS
screen appears.
02
RETURN
3 Press 1or 2to select
the desired file.
CAUTION:
While performing the above, never disconnect
power, as this may cause the memory card to be
corrupted.
Select
NOTE:
When the image is printed from the printer, a
black bar appears at the bottom of the screen.
This is not a malfunction. By recording with “DIS”
de-activated (੬ pg. 32) this can be avoided.
4 Press 4or 3to select the number indication
(00), and press SET.
5 Select the number of prints
Select
by pressing 3to increase the
number, or 4to decrease the
number, and press SET.
Initializing A Memory Card
You can initialize a memory card any time.
After initializing, all files and data stored in the
memory card, including those which have
been protected, are cleared.
SET
● Repeat steps 3 through 5
DPOF
for the desired number of
SHEETS
prints.
1 Perform steps 1 – 3 in “Normal Playback Of
● The number of prints can
be set up to 15.
● To correct the number of
prints, select the image
again and change the number.
Images” (੬ pg. 27).
02
2 Press MENU.
Select
3 Select “FORMAT”, press SET
or 2. The FORMAT screen
appears.
6 Select “RETURN”, press
DPOF
SET. The “SAVE?”
appears.
● Press 1whenever you want to
SAVE?
return to the previous menu
screen.
SET
● If you did not change any
settings in step 3 through
5, the DPOF Menu
reappears.
EXECUTE
CANCEL
4 Select “EXECUTE”,
FORMAT
ERASE ALL
EXISTING DATA?
press SET.The memory
card is initialized.
7 Select “EXECUTE”, press SET.
● When initialization is
finished, “NO IMAGES
STORED” appears.
EXECUTE
CANCEL
● To cancel selection, select “CANCEL”.
● To cancel initialization, select “RETURN”.
MENUS FOR DETAILED ADJUSTMENT
EN
31
4 Select the desired function, press SET or 2.
Changing The Menu Settings
The selected function menu appears.
This camcorder is equipped with an easy-to-
use, on-screen menu system that simplifies
many of the more detailed camcorder settings.
(੬ pg. 31 – 35)
Example: FUNCTION menu.
Current Setting
FUNCTION
VIDEO/MEMORY
Power Switch
OFF
W
IPE/FADER
OFF
OFF
PROGRAM AE
EFFECT
0
AUTO
W
OFF
SHUTTER
EXIT
Lock
Button
5 Select the desired selection, press SET or
2.
Select
Example: WIPE/FADER menu.
WIPE/FADER
OFF
OFF
WH
BK
BLACK
SET
SLIDE
MENU
SCROLL
1 For Video and D.S.C. Recording Menus:
● Set the VIDEO/MEMORY Switch to “VIDEO”
or “MEMORY”.
● Set the Power Switch to “REC” while
pressing down the Lock Button located on
the switch.
6 Select the desired setting, press SET or 2.
Selection is completed.
7 Press MENU. The Menu Screen closes.
● Set the recording mode to “ ”. (੬ pg. 20)
For Video Playback Menu:
● Set the VIDEO/MEMORY Switch to
“VIDEO”.
● Set the Power Switch to “PLAY” while
pressing down the Lock Button located on
the switch.
● Press 1whenever you want to cancel or return
to the previous menu screen.
● Repeat the procedure if you wish to set other
function menus.
● For D.S.C. Playback Menu, refer to “D.S.C.
PLAYBACK” (੬ pg. 27).
2 Open the LCD monitor fully. (੬ pg. 8)
3 Press MENU. The Menu Screen appears.
Screen for Video and
Screen for Video
D.S.C. Recording Menu Playback Menu
FUNCTION
CAMERA
VTR
VTR
DISPLAY
SYSTEM
DISPLAY
SYSTEM
EXIT
EXIT
* Video Recording Menu only
MENUS FOR DETAILED ADJUSTMENT
EN
In the following pages, [ ] refers to Factory
32
CAMERA
preset settings.
The following menu settings can be changed
only when the Power Switch is set to “REC”.
Recording Menus
[34X]: When set to “34X” while using digital
zoom, the zoom magnification will reset to 34X
since digital zoom will be disengaged.
68X*: Allows you to use the Digital Zoom. By
digitally processing and magnifying images,
zooming is possible from 34X (the optical
zoom limit), to a maximum of 68X digital
magnification.
FUNCTION
● The following menu settings can be changed
● Each setting (except “EFFECT” and
“SHUTTER”) which is set in Video Recording
Menu.
900X*: Allows you to use the Digital Zoom. By
zooming is possible from 34X (the optical
zoom limit), to a maximum of 900X digital
magnification.
WIPE/FADER*
(੬ pg. 40), “Wipe or Fader Effects”
* Available only when the VIDEO/MEMORY
Switch is set to “VIDEO”.
* Available only when the VIDEO/MEMORY
Switch is set to “VIDEO”.
PROGRAM AE
(੬ pg. 41), “Program AE, Effects And Shutter
Effects”
TELE MACRO
[OFF]: Disables the function.
EFFECT
ON: When the distance to the subject is less
than 1 m (3.3 ft), set “TELE MACRO” to “ON”.
You can shoot a subject as large as possible at
a distance of approx. 40 cm (1.4 ft).
(੬ pg. 41), “Program AE, Effects And Shutter
Effects”
EXPOSURE
(੬ pg. 38), “Exposure Control”
Depending on the zoom position, the lens may go
out of focus.
W. BALANCE
(੬ pg. 39), “White Balance Adjustment”
DIS*
OFF
: Disables the function. (DIS disable
icon appears.)
SHUTTER
[ON]: To compensate for unstable images
caused by camera-shake, particularly at high
magnification.
(੬ pg. 41), “Program AE, Effects And Shutter
Effects”
NOTES:
● Accurate stabilization may not be possible if
hand shake is excessive, or depending on the
shooting condition.
● Switch off this mode when recording with the
camcorder on a tripod.
● DIS cannot be activated when “NIGHT” in
“PROGRAM AE” or “STROBE” in “EFFECT” is
selected, or when LIGHT is set to on, or when
SNAPSHOT is pressed.
* Available only when the VIDEO/MEMORY
Switch is set to “VIDEO”.
MENUS FOR DETAILED ADJUSTMENT
EN
33
VTR
GAIN UP
OFF: Allows you to shoot dark scenes with no
picture brightness adjustment.
[AGC]: The overall appearance may be grainy,
but the image is bright.
Available only when the VIDEO/MEMORY
Switch is set to “VIDEO”.
REC MODE
AUTO
: The shutter speed is
[SP]*: To record in the SP (Standard Play)
automatically adjusted. Shooting a subject in
low or poor lighting at slow shutter speed
provides a brighter image than in the AGC
mode, but the subject’s movements are not
smooth or natural. The overall appearance
may be grainy. While the shutter speed is
mode
LP: Long Play—more economical, providing
1.5 times the recording time.
* SP indicator does not appear on the screen.
NOTES:
● Audio Dubbing (੬ pg. 45) and Insert Editing
(੬ pg. 45) are possible on tapes recorded in
the SP mode.
being automatically adjusted, “
displayed.
” is
picture will be blurred at the switching point.
camcorder, blocks of noise may appear or there
may be momentary pauses in the sound.
WIND CUT*
[OFF]: Disengages the function.
ON
: Helps cut down on noise created by
wind. The “
” indicator appears. The quality
of the sound will change. This is normal.
* Available only when the VIDEO/MEMORY
Switch is set to “VIDEO”.
SOUND MODE
[12BIT]: Enables video recording of stereo
sound on four separate channels, and is
recommended for use when performing Audio
Dubbing. (Equivalent to the 32 kHz mode of
previous models)
16BIT: Enables video recording of stereo
sound on two separate channels. (Equivalent
to the 48 kHz mode of previous models)
IMAGE SIZE*
[640 x 480 F] / 640 x 480 S
The Image Size mode can be selected to best
match your needs. Two Picture Quality modes
640F
are available: FINE (
) and STANDARD
640S
(
) (in order of quality).
NOTE:
SNAP/SLOW
The number of storable images depends on the
selected picture quality as well as the composition
of the subjects in the images and the type of
memory card being used. (੬ pg. 26)
* Available only when the VIDEO/MEMORY
Switch is set to “MEMORY”.
[SNAP
SLOW
]: Snapshot mode
: Live Slow mode
For details on the procedure, refer to “Live
Slow” (੬ pg. 36) and “Snapshot (Record Still
Image On Tape)” (੬ pg. 37).
REC SELECT
(TAPE): When Snapshot recording is
performed with the VIDEO/MEMORY Switch
set to “VIDEO”, still images are recorded only
onto the tape.
/
(TAPE/CARD): When Snapshot
recording is performed with the VIDEO/
MEMORY Switch set to “VIDEO”, still images
are recorded not only onto the tape but also in
the memory card (640 x 480 pixels).
[
(CARD)]: When Snapshot recording is
performed with the VIDEO/MEMORY Switch
Set to “VIDEO”, still images are recorded into
the Memory Card only. Select this setting to
perform Dual Rec.. (੬ pg. 20)
MENUS FOR DETAILED ADJUSTMENT
EN
34
DISPLAY
MELODY
OFF: Even though not heard while shooting,
[ON]: A melody sounds when any operation is
performed. It also activates the shutter sound
effect. (੬ pg. 26, 37)
ADJ.”, “16:9 OUTPUT” and “BRIGHT”) are
effective only for shooting.
ON SCREEN
LCD: Keeps the camcorder’s display (except
the date, time and time code) from appearing
on the connected TV screen.
[LCD/TV]: Makes the camcorder’s display
appear on screen when the camcorder is
connected to a TV.
REMOTE
[ON]: Enables the remote control operations.
PRIORITY
[LCD]: The image is displayed on the LCD
monitor when the viewfinder is pulled out while
the LCD monitor is opened.
FINDER: The image is displayed in the
viewfinder when the viewfinder is pulled out
while the LCD monitor is opened.
DATE/TIME
[OFF]: The date/time does not appear.
ON: The date/time is always displayed.
● The date indication can also be turned on/off by
pressing the DISPLAY Button on the remote
control. (੬ pg. 23, 42)
CLOCK ADJ.
੬ pg. 15, “Date/Time Settings”
OFF: Automatic demonstration will not take
place.
[ON]: Demonstrates certain functions such as
Wipe/Fader and Effects, etc., and can be used
to confirm how these functions operate.
Demonstration starts in the following cases:
● When the Menu Screen is closed after “DEMO
MODE” is turned “ON”.
● With “DEMO MODE” set to “ON”, if there is no
operation for about 3 minutes after the Power
Switch is set to “REC”.
● Performing any operation during the
demonstration stops the demonstration
temporarily. If no operation is performed for
more than 3 minutes after that, the
demonstration will resume.
TIME CODE*
[OFF]: Time code is not displayed.
ON: Time code is displayed on the camcorder
and on the connected TV. Frame numbers are
not displayed during recording. (੬ pg. 20)
* Available only when the VIDEO/MEMORY
Switch is set to “VIDEO”.
16:9 OUTPUT
wide mode, set the tv screen size correctly.
4:3 TV: For TV with an aspect ratio of 4:3.
[16:9 TV]: For TV with an aspect ratio of 16:9.
NOTES:
BRIGHT
● If a cassette is in the camcorder, the
demonstration cannot be turned on.
● “DEMO MODE” remains “ON” even if the
camcorder power is turned off.
੬ pg. 15, “Brightness Adjustment Of The
Display”
SYSTEM
CAM RESET
[CANCEL]: Does not reset all settings to the
factory-preset.
EXECUTE: Resets all settings to the factory-
preset.
The “SYSTEM” functions which are set when
the Power Switch is set to “REC” are also
applied when the Power Switch is set to
“PLAY”.
LANGUAGE
/
/
/ [ENGLISH] /
FRANCAIS / ESPAÑOL / PORTUGUÊS
The language setting can be changed.
(੬ pg. 14)
MENUS FOR DETAILED ADJUSTMENT
EN
DISPLAY
Playback Menus
Each setting (except “OFF” in “ON SCREEN”,
Switch is set to “REC”.
VTR
The settings below are effective only for video
playback except “REC MODE” and “SNAP/
SLOW”. The parameters (except “SOUND L/
R”, “[T] ➝ [M] COPY” and “NARRATION”
settings) are the same as in the description on
page 33.
The parameters (except “OFF” in “ON
SCREEN” setting) are the same as in the
description on ੬ pg. 34.
ON SCREEN
OFF / [LCD] / LCD/TV
SOUND L/R and NARRATION
When set to “OFF”, the camcorder’s display
disappears.
During tape playback, the camcorder detects
the sound mode in which the recording was
made, and plays the sound back. Select the
sound to accompany your playback picture.
DATE/TIME
[OFF] / ON
CLOCK ADJ.
੬ pg. 15, “Date/Time Settings”
REC MODE
[SP]* / LP
Allows you to set the video recording mode
(SP or LP) depending on your preference. It is
recommended you use “REC MODE” in
VIDEO Menu when using this camcorder as a
recorder during dubbing. (੬ pg. 42, 43)
* SP indicator does not appear on the screen.
TIME CODE [OFF] / ON
੬ pg. 20, “Time Code”
16:9 OUTPUT
4:3 TV / [16:9 TV]
੬ pg. 34, “16:9 OUTPUT”
NARRATION
BRIGHT
[OFF]: Original sound is output on both “L” and
“R” channels in stereo.
੬ pg. 15, “Brightness Adjustment Of The
Display”
ON: Dubbed sound is output on both “L” and
“R” channels in stereo. (੬ pg. 45).
MIX: Original and dubbed sounds are
combined and output in stereo on both “L” and
“R” channels.
SYSTEM
Each setting (except “DEMO MODE”) is linked
with “SYSTEM”, which appears when the
Power Switch is set to “REC”.
SNAP/SLOW
੬ pg. 33, “SNAP/SLOW”.
The parameters are the same as in the
description on page 34.
[T] ➝ [M] COPY
[OFF]: When the SNAPSHOT button is
pressed during tape playback, the playback
image pauses and normal playback will
resume after approximately 6 seconds. (The
still image is not recorded.)
ON: Enables dubbing of images recorded on a
tape to a memory card. (੬ pg. 42).
SOUND L/R
[STEREO
]: Sound is output on both “L” and
“R” channels in stereo.
SOUND L : Sound from the “L” channel is
output.
SOUND R : Sound from the “R” channel is
output.
FEATURES FOR RECORDING
EN
36
LED Light
LED Light can be used to
brighten the subject in the dark
place during video recording or
D.S.C. shooting.
Live Slow
This feature is useful for recording or playing
back precious or hard-to-see moments at a
slow speed. Sound is recorded and played
back in real time.
1 Set the VIDEO/MEMORY Switch to
LIGHT
“VIDEO”.
LED Light
2 Set the Power Switch to “REC” or “PLAY”.
● If set to “REC”, the recording mode should be
set to “ ”. (੬ pg. 20)
1 Press LIGHT repeatedly to change the
setting.
3 Set “SNAP/SLOW” to “SLOW”. (੬ pg. 33)
appears.)
The Live Slow indicator “ ” appears.
The light is on always. (
4 Press SLOW during recording or playback.
● The moving pictures are divided into four
frames. They are recorded or played back for
1.5 seconds, and then normal recording or
playback resumes.
The light turns on automatically
when dark. (
appears.)
Turns off the light.
NOTES:
2 Press the Recording Start/Stop Button to
start video recording or SNAPSHOT to shoot a
still image.
● This feature is effective when the recording
mode selection is set to both “ ” or “ ”.
● Live Slow cannot be used when the 16:9 Wide
mode is selected.
NOTES:
●
Be careful not to point the LED Light directly to
eyes.
● If the light does not reach the subject when the
LED Light setting is “ON”, the Night-Alive
function will be activated, and makes it possible
to shoot the subject brighter.
● Since subjects are shot at a reduced shutter
speed when the LED Light setting is “ON”, they
will appear slightly blurred.
FEATURES FOR RECORDING
EN
37
Snapshot (Record Still Image On
Tape)
This feature lets you record still images that
look like photographs onto a tape.
Manual Focus
The camcorder’s Full Range AF system offers
continuous shooting ability from close-up (as
close as approx. 5 cm (2") to the subject) to
infinity.
depending on the shooting condition. In this
case, use the manual focus mode.
1 Set the VIDEO/MEMORY Switch to
“VIDEO”.
2 Set the Power Switch to “REC”.
1 Set the Power Switch to “REC”.
3 Set the recording mode to “ ”. (੬ pg. 20)
4 Set “REC SELECT” to “
/
” or
FOCUS
“
“. (੬ pg. 31, 33)
5 Set “SNAP/SLOW” to “SNAP”. (੬ pg. 33)
1
2
6 Press SNAPSHOT.
● The “PHOTO” indication appears and a still image
will be recorded for approx. 5 seconds, then the
camcorder re-enters the Record-Standby mode.
● You can perform Snapshot also during
recording. A still image will be recorded for
approx. 5 seconds, then the normal recording
resumes.
● Snapshot is effective when the recording mode
selection is set to both “ ” or “ ”.
● If the image taken by snapshot is too dark or too
SET
Manual focus indicator
2 Set the recording mode to “ ”. (੬ pg. 20)
3 Press FOCUS. The manual focus indicator
appears.
4 Press 1or 2to focus on a subject.
● When the focus level cannot be adjusted any
further or closer, “ ” or “ ” will blink.
bright, select
(੬ pg. 39) or “SPOTLIGHT”
(੬ pg. 41).
5 Press SET. Focus adjustment is complete.
Motor Drive Mode
To reset to Auto Focus
Press FOCUS twice.
Keeping SNAPSHOT pressed in step 6
provides an effect similar to serial photography.
(Interval between still images: approx. 1
second)
Manual focus is recommended in
situations listed below.
● When two subjects overlap in the same scene.
● When illumination is low.*
● When the subject has no contrast (difference in
brightness and darkness), such as a flat, one-
color wall, or a clear, blue sky.*
● The Motor Drive mode is disabled when “REC
SELECT” is set to “
/
” or “
“.
(੬ pg. 33)
● When a dark object is barely visible in the LCD
monitor or the viewfinder.*
● When the scene contains minute patterns or
identical patterns that are regularly repeated.
● When the scene is affected by sunbeams or
light reflecting off the surface of a body of water.
● When shooting a scene with a high-contrast
background.
* The following low-contrast warnings appear
blinking:
,
,
and
.
FEATURES FOR RECORDING
EN
38
Exposure Control
Manual exposure control is recommended in
the following situations:
● When shooting using reverse lighting or when
the background is too bright.
● When shooting on a reflective natural
background such as at the beach or when
skiing.
Iris Lock
contracts in well-lit environments to keep too
much light from entering, and dilates in dim
environments to allow in more light.
Use this function in the following situations:
● When shooting a moving subject.
● When the distance to the subject changes (so
its size in the LCD monitor or the viewfinder
changes), such as when the subject is backing
away.
● When the background is overly dark or the
subject is bright.
Select
● When shooting on a reflective natural
background such as at the beach or when
skiing.
● When shooting objects under a spotlight.
● When zooming.
EXPOSURE
0
SET
(੬ pg. 38)
1 Open the LCD monitor fully.
2 Set the Power Switch to “REC”.
LCD monitor or the viewfinder, then press and
3 Set the recording mode to “ ”. (੬ pg. 20)
4 Press MENU.
hold SET or 2for over 2 seconds. The “
”
indication appears.
3 Press SET or 2. The iris is locked.
5 Select “FUNCTION”, press SET or 2.
6 Select “EXPOSURE”, press SET or 2.
4 Press MENU.
7 Select the appropriate exposure, press SET
or 2.
● To brighten the image, press 3. To darken the
image, press 4. (maximum +/-6)
8 Press MENU.
NOTES:
● If the adjustment does not cause any visible
change in brightness, set “GAIN UP” to “AUTO”.
(੬ pg. 31, 33)
● You cannot use the manual exposure control at
the same time when “PROGRAM AE” is set to
“SPOTLIGHT” or “SNOW” (੬ pg. 41), or with
the backlight compensation.
FEATURES FOR RECORDING
EN
39
Backlight Compensation
Backlight compensation brightens the subject
quickly.
White Balance Adjustment
The white balance refers to the correctness of
color reproduction under various lighting. If the
With simple operation, backlight compensation white balance is correct, all other colors will be
feature brightens the dark subject portion by
increasing the exposure.
accurately reproduced.
The white balance is usually adjusted
automatically. However, more advanced
camcorder operators control this function
manually to achieve a more professional color/
tint reproduction.
1 Set the Power Switch to
“REC”.
SET
2 Set the recording mode to
“
”. (੬ pg. 20)
To change the setting
Set “W. BALANCE” to the desired mode.
(੬ pg. 32)
● The selected mode indicator except “AUTO”
appears.
3 Press
so that the
Backlight Compensation
indicator “ ” appears.
To cancel Backlight Compensation
[AUTO]: White balance is adjusted
automatically.
Press
twice so that the “ ” indicator
disappears.
MWB: Adjust the white balance
manually when shooting under various types
of lighting. (੬ “Manual White Balance
Adjustment”, pg. 40)
NOTE:
Using Backlight Compensation may cause the
light around the subject to become too bright and
the subject to become white.
FINE: Outdoors on a sunny day.
CLOUD: Outdoors on a cloudy day.
HALOGEN: A video light or similar type
of lighting is used.
Spot Exposure Control
Selection of a spot metering area enables
more precise exposure compensation.
1 Set the Power Switch to “REC”.
2 Set the recording mode to “ ”. (੬ pg. 20)
3 Press
twice so that the Spot Exposure
Control indicator “
” appears.
● A spot metering area frame appears at the
center of the LCD monitor/viewfinder.
4 Press SET.
● Spot Exposure Control is engaged.
● Exposure is adjusted to make the brightness of
the selected area most appropriate.
To lock the iris
After step 3, press and hold SET over 2
seconds. The “ ” indication appears and the
iris is locked.
To cancel Spot Exposure Control
Press
once so that the “
” indicator
disappears.
NOTES:
● Depending on the shooting location and
condition, optimum result may not be attained.
● “STROBE” in “EFFECT” cannot be used with
Spot Exposure Control.
EN
40
Manual White Balance
Adjustment
Adjust the white
balance manually
when shooting under
various types of
lighting.
Wipe Or Fader Effects
These effects let you make pro-style scene
transitions. Use them to spice up the transition
from one scene to the next.
Wipe or Fader works when video recording is
started or stopped.
1 Set the VIDEO/MEMORY Switch to
“VIDEO”.
1 Set the Power
White paper
2 Set the Power Switch to “REC”.
Switch to “REC”.
3 Set the recording mode to “ ”. (੬ pg. 20)
2 Set the recording mode to “ ”. (੬ pg. 20)
4 Set “WIPE/FADER” in “FUNCTION” Menu.
3 Hold a sheet of plain white paper in front of
the subject. Adjust zoom or position yourself
so that the white paper fills the screen.
(੬ pg. 32)
5 Press the Recording Start/Stop Button to
activate the Fade-in/out or Wipe-in/out.
4 Select “MWB” in “W. BALANCE” menu
(੬ pg. 32), then press and hold SET or 2until
begins blinking.
● When the setting is completed,
blinking.
NOTE:
pressing and holding the Recording Start/Stop
Button.
stops
5 Press SET or 2to engage the setting.
WIPE/FADER
6 Press MENU.The Menu Screen closes and
the Manual White Balance indicator
displayed.
is
OFF: Disables the function. (Factory-preset)
WHITE
screen.
: Fade in or out with a white
: Fade in or out with a black
: Wipe in from right to left, or wipe
NOTES:
● In step 3, it may be difficult to focus on the white
paper. In such a case, adjust focus manually.
(੬ pg. 37)
BLACK
screen.
● Because the color temperature is different
depending on the light source, use this function
for a more natural result.
● Once you adjust white balance manually, the
setting is retained even if the power is turned off
or the battery removed.
SLIDE
out from left to right.
SCROLL
: The scene wipes in from the
bottom to the top of a black screen, or wipes
out from top to bottom, leaving a black screen.
● White Balance cannot be activated
simultaneously with “TWILIGHT” in “PROGRAM
AE” (੬ pg. 41).
● White Balance cannot be activated if the
“SEPIA” or “MONOTONE” mode is activated.
FEATURES FOR RECORDING
EN
41
NIGHT
: Makes dark subjects or areas
Program AE, Effects And Shutter
Effects
even brighter than they would be under good
natural lighting. Although the recorded image
is not grainy, it may look as if it is strobing due
to the slow shutter speed.
During Night-Alive, it may be difficult to bring
the camcorder into focus. To prevent this, use
of a tripod is recommended.
1 Set the Power Switch to “REC”.
2 Set the recording mode to “ ”. (੬ pg. 20)
3 Set “EFFECT”, “PROGRAM AE” or
“SHUTTER” in “FUNCTION” Menu. (੬ pg. 32)
● The selected effect will be shown for approx. 2
seconds before the camcorder returns to the
menu screen.
EFFECT
OFF: Disables the function. (Factory-preset)
SEPIA
: Recorded scenes have a brownish
NOTES:
tint like old photos.
● Shutter Effects cannot be used during “NIGHT”.
● When a subject is too bright or reflective, a
vertical streak may appear (smear
phenomenon). Smear phenomenon tends to
occur when “SPORTS” or any mode of
“SHUTTER 1/500 – 1/4000” is selected.
MONOTONE
: Like classic black and white
films, your footage is shot in B/W.
CLASSIC*
: Gives recorded scenes a
strobe effect.
STROBE*
:Your recording looks like a
series of consecutive snapshots.
PROGRAM AE
MIRROR*
: Creates a mirror image on the
image on the other half.
OFF: Disables the function. (Factory-preset)
SPORTS
* Not available for still image recording.
(Variable Shutter Speed: 1/250 – 1/4000):
This setting allows fast-moving images to be
captured one frame at a time, for vivid, stable
slow-motion playback. The faster the shutter
speed, the darker the picture becomes. Use
the shutter function under good lighting
conditions.
SHUTTER
OFF: Disables the function. (Factory-preset)
SHUTTER 1/60: The shutter speed is
fixed at 1/60th of a second. Black bands that
usually appear when shooting a TV screen
become narrower.
SHUTTER 1/100: The shutter speed is
fixed at 1/100th of a second.The flickering that
occurs when shooting under a fluorescent light
or mercury-vapour lamp is reduced.
SNOW
: Compensates for subjects that
may otherwise appear too dark when shooting
in extremely bright surroundings such as in the
snow.
SPOTLIGHT
: Compensates for subjects
that may otherwise appear too bright when
shooting under extremely strong direct lighting
such as spotlights.
SHUTTER 1/500/SHUTTER 1/4000*:
(Refer to PROGRAM AE - SPORTS
mode.)
* Not available for still image recording.
TWILIGHT
: Makes evening scenes look
more natural. White Balance (੬ pg. 39) is
automatically set to “AUTO”. When Twilight is
chosen, the camcorder automatically adjusts
the focus from approx. 10 m (32 ft) to infinity.
From less than 10 m, adjust the focus
manually.
FEATURES FOR RECORDINGS
EN
EDITING
42
Dubbing Still Images Recorded On
A Tape To A Memory Card
Dubbing To A VCR
To use this camcorder as a player
Still images can be dubbed from a tape to a
memory card.
1 Following the illustration, ੬ pg. 23,
“Connections To A TV Or VCR” , connect the
camcorder and the VCR’s input connectors.
1 Load a cassette. (੬ pg. 16)
2 Load a memory card. (੬ pg. 17)
recording on the VCR. (Refer to the VCR’s
instruction manual.)
3 Set “SNAP/SLOW” to the desired mode.
(except “SLOW”, ੬ pg. 33, 35)
4 Set the VIDEO/MEMORY Switch to
4 To stop dubbing, stop recording on the
“VIDEO”.
VCR, then stop playback on the camcorder.
5 Set the Power Switch to “PLAY” while
pressing down the Lock Button located on the
switch.
NOTES:
● It is recommended to use the AC Adapter as
the power supply instead of the battery
pack. (੬ pg. 13)
6 Set “[T] ➝ [M] COPY” to “ON”. (੬ pg. 35)
● To choose whether or not the following displays
appear on the connected TV
• Date/time
Set “DATE/TIME” to “ON” or “OFF”
(੬ pg. 35). Or, press DISPLAY on the remote
control to turn on/off the date indication.
• Time code
Set “TIME CODE” to “OFF” or “ON”
(੬ pg. 35).
• Indications other than date/time and time code
Set “ON SCREEN” to “OFF”, “LCD” or “LCD/
TV” (੬ pg. 35).
7 Press 6 to start playback.
8 At the point you want to dub, press 6
again to engage Still Playback.
9 To dub the image, press SNAPSHOT.
● The “
” indication appears during dubbing.
NOTE:
To use Playback Special effects with a video
image you wish to dub, perform up to step 9 using
the remote control. (੬ pg. 24)
EDITING
EN
43
NOTES:
Dubbing To Or From A Video Unit
Equipped With A DV Connector
(Digital Dubbing)
It is also possible to copy recorded scenes
from the camcorder onto another video unit
equipped with a DV connector. Since a digital
signal is sent, there is little, if any, image or
sound deterioration.
● It is recommended to use the AC Adapter as
the power supply instead of the battery
pack. (੬ pg. 13)
● If a blank portion or disturbed image is played
back on the player during dubbing, the dubbing
may stop so that an unusual image is not
dubbed.
● Even though the DV cable is connected
correctly, sometimes the image may not appear
make connections again.
● If “Playback Zoom” (੬ pg. 25) or “Playback
Special Effects” (੬ pg. 25) is attempted or
SNAPSHOT is pressed during playback, only
the original playback image recorded on the
tape is output from the DV IN/OUT connector.
● When using a DV cable, be sure to use the
optional JVC VC-VDV204U or VC-VDV206U
DV cable.
To DV IN/OUT
To use this camcorder as a recorder
1 Make sure all units are turned off.
2 Connect this camcorder to a video unit
equipped with a DV output connector using a
DV cable as shown in the illustration.
3 Set the camcorder’s Power Switch to
DV cable (optional)
To DV IN/OUT
Core filter
“PLAY”.
4 Set “REC MODE” to “SP” or “LP”.
(੬ pg. 35)
5 Start playback on the player.
6 Press the Recording Start/Stop Button to
engage the Record-Pause mode.
• The “
” indication appears on the
DV IN
screen.
Video unit equipped with DV connector
To use this camcorder as a player
1 Make sure all units are turned off.
7 At the point you want to start dubbing, press
the Recording Start/Stop Button to start
dubbing. The
indication rotates.
8 Press the Recording Start/Stop Button
again to stop dubbing. The
stops rotating.
indication
2 Connect this camcorder to a video unit
equipped with a DV input connector using a DV
cable as shown in the illustration.
9 Press 7 to return to the normal playback
mode.
3 Start playback on the camcorder.
(੬ pg. 21)
NOTE:
Digital Dubbing is performed in the sound mode
recorded on the original tape, regardless of the
current “SOUND MODE” setting. (੬ pg. 33)
4 At the point you want to start dubbing, start
recording on the video unit. (Refer to the video
unit’s instruction manual.)
COPY PROTECTED
5 To stop dubbing, stop recording on the
video unit, then stop playback on this
camcorder.
Appears if dubbing of copyguarded signals is
attempted while this camcorder is being used
as a recorder.
EDITING
EN
44
[A] Using USB cable
It is possible to transfer still images stored on a
memory card to a PC.
Connection To A Personal
Computer
[A] Using USB
cable
[B] Using DV
[B] Using DV cable
cable
OR
It is also possible to transfer still/moving
images to a PC with a DV connector by using
the provided software, software equipped with
the PC or commercially available software.
If you are using a Windows® XP, you can use
Windows® Messenger to conduct video
conferences over the Internet, using a
camcorder. For details, refer to the help for the
Windows® Messenger.
To DV IN/OUT
Core filter
To USB
NOTES:
● Refer to “SOFTWARE INSTALLATION AND
USB CONNECTION GUIDE” for the bundled
software and drivers.
● It is recommended to use the AC Adapter as
the power supply instead of the battery pack.
(੬ pg. 13)
● Never connect the USB cable and the DV
cable simultaneously to the camcorder.
Connect only the cable you wish to use to
the camcorder.
DV cable
(optional)
USB cable
(provided)
Core filter
● When using a DV cable, be sure to use the
optional JVC VC-VDV206U or VC-VDV204U
DV cable depending on the type of DV
connector (4 or 6 pins) on the PC.
● If the PC connected to the camcorder via the
USB cable is not powered, the camcorder does
not enter the USB mode.
To DV
connector
To USB
connector
or
● The date/time information cannot be captured
into the PC.
● Refer to the instruction manuals of the PC and
Software.
● The still images can also be transferred to a PC
with a DV connector-equipped capture board.
● The system may not work properly depending
on the PC or capture board you are using.
● If, after connecting a DV cable to the camcoder
and it doesn’t work, restart the camcoder.
PC
PC with DV connector
When connecting the camcorder to a PC
using a DV cable, make sure to follow the
procedure below. Connecting the cable
incorrectly may cause malfunctions to the
camcorder and/or the PC.
● Connect the DV cable first to the PC, and
then to the camcorder.
● Connect the DV cable (plugs) correctly
according to the shape of the DV connector.
“USB” and/or “
” appears on the
LCD monitor while the PC is accessing data
in the camcorder or the camcorder is
transferring a file to the PC.
NEVER disconnect the USB cable while
“
” is displayed on the LCD
monitor since this can result in product
damage.
EDITING
EN
45
Audio Dubbing
Insert Editing
The audio track can be customized only when
recorded in the 12-BIT and SP modes.
(੬ pg. 33)
You can record a new scene into a previously
recorded tape, replacing a section of the
original recording with minimal picture
distortion at the in and out points. The original
audio remains unchanged.
● Use the provided remote control.
Speaker
● Use the provided remote control.
NOTES:
● Before performing the following steps, make
sure that “TIME CODE” for “DISPLAY” in both
Recording and Playback Menus is set to “ON”.
(੬ pg. 34, 35)
START/
STOP
PAUSE
PLAY
STOP
REW
INSERT
● Insert Editing is not possible on a tape recorded
in the LP mode or on a blank portion of a tape.
A.DUB
Stereo
Microphone
1 Play back the tape, locate the Edit-Out point
and press PAUSE (8). Confirm the time code
at this point. (੬ pg. 20)
1 Play back the tape to locate the point where
editing will start, then press PAUSE (8).
2 Press REW (1) until the Edit-In point is
2 While holding A. DUB ( ) on the remote
control, press PAUSE (8). The “8 ” indicator
appears.
located, then press PAUSE (8).
3 Press and hold INSERT ( ) on the remote
control, then press PAUSE (8). The “8
”
3 Press PLAY (3), then begin “narrating”.
indicator and the Time Code (min.:sec.)
Speak into the microphone.
appear and the camcorder enters Insert-Pause
mode.
● To pause dubbing, press PAUSE (8).
4 To end Audio Dubbing, press PAUSE (8),
4 Press START/STOP to begin editing.
● Confirm the insert at the time code you checked
in step 1.
● To pause editing, press START/STOP. Press it
again to resume editing.
then STOP (7).
To hear the dubbed sound during playback
Set “NARRATION” to “ON” or “MIX”
(੬ pg. 35).
5 To end Insert Editing, press START/STOP,
NOTES:
● Sound is not heard from the speaker during
Audio Dubbing.
then STOP (7) on the remote control.
NOTES:
● When editing onto a tape that was recorded at
12-BIT, the old and new soundtracks are
recorded separately.
● If feedback or howling occurs during TV
playback, move the camcorder’s microphone
away from the TV, or turn down the TV’s volume.
● Program AE, Effects and Shutter Effects
(੬ pg. 41) can be used to spice up the scenes
being edited during Insert Editing.
● During Insert Editing, the date and time
information changes.
● If you perform Insert Editing onto a blank space
on the tape, the audio and video may be
disrupted. Make sure you only edit recorded
areas.
● During Insert Editing, when the tape moves to
scenes recorded in the LP mode or a blank
portion, Insert Editing stops.
TROUBLESHOOTING
EN
If, after following the steps in the chart below,
the problem still exists, please consult your
nearest JVC dealer.
46
The focus does not adjust automatically.
● Focus is set to the Manual mode.
➜Set Focus to the Auto mode. (੬ pg. 37)
● The lens is dirty or covered with condensation.
➜Clean the lens and check the focus again.
(੬ pg. 37)
No power is supplied.
● The power is not connected properly.
➜Connect the AC Adapter securely. (੬ pg. 13)
● The battery pack is not attached firmly.
➜Detach the battery pack once again and re-
attach it firmly. (੬ pg. 14)
● The battery is dead.
➜Replace the dead battery with a fully charged
one. (੬ pg. 13)
The color of Snapshot looks strange.
● The light source or the subject does not include
white. Or there are various different light
sources behind the subject.
➜Find a white subject and compose your shot so
that it also appears in the frame. (੬ pg. 37, 40)
Recording cannot be performed.
The POWER/CHARGE lamp on the
camcorder does not light during charging.
● The tape’s erase protection tab is set to “SAVE”.
➜Set the tape’s erase protection tab to “REC”.
(੬ pg. 16)
● Charging is difficult in places subject to
extremely high/low temperatures.
➜To protect the battery, it is recommended to
charge it in places with a temperature of 10°C
to 35°C (50°F to 95°F). (੬ pg. 48)
● The battery pack is not attached firmly.
➜Detach the battery pack once again and re-
attach it firmly. (੬ pg. 13)
● “TAPE END” appears.
➜Replace with new cassette. (੬ pg. 16)
● The cassette holder cover is open.
➜Close the cassette holder cover.
When shooting a subject illuminated by
bright light, vertical lines appear.
This is not a malfunction.
too slow.
When the screen is under direct sunlight
during shooting, the screen becomes red
or black for an instant.
● When shooting in the dark, the unit becomes
highly sensitive to light when “GAIN UP” is set
to “AUTO”.
“GAIN UP” to “AGC” or “OFF”. (੬ pg. 33)
This is not a malfunction
The LCD monitor or viewfinder indications
blink.
Images on the LCD monitor appear dark
or whitish.
● Effects function that cannot be used together
are selected at the same time.
➜Re-read the sections covering Effects.
(੬ pg. 32)
● In places subject to low temperature, images
become dark due to the characteristics of the
LCD monitor. This is not a malfunction.
➜Adjust the brightness and angle of the LCD
monitor. (੬ pg. 8, 15)
● When the LCD monitor’s fluorescent light
reaches the end of its service life, images on
the LCD monitor become dark.
The tape is moving, but there is no
picture.
● Your TV has AV input terminals, but is not set to
its VIDEO mode.
➜Set the TV to the mode or channel appropriate
for video playback. (੬ pg. 23)
● The cassette holder cover is open.
➜Close the cassette holder cover. (੬ pg. 16)
➜Consult your nearest JVC dealer.
Picture does not appear on the LCD
monitor.
● The viewfinder is pulled out and “PRIORITY” is
set to “FINDER”.
➜Push the viewfinder back in or set “PRIORITY”
to “LCD”. (੬ pg. 8, 34)
Blocks of noise appear during playback,
or there is no playback picture and the
screen becomes blue.
● The LCD monitor’s brightness setting is too
dark.
➜Adjust the brightness of the LCD monitor.
(੬ pg. 15)
Clean the video heads with an optional cleaning
cassette. (੬ pg. 5)
TROUBLESHOOTING
● Appears if A. DUB ( ) on the remote control is
pressed when the erase protection tab is set to
“SAVE”. (੬ pg. 45)
EN
47
➜If the monitor is tilted upward 180 degrees,
open the monitor fully. (੬ pg. 8)
Aspect ratio is strange
INSERT ERROR!
<CANNOT EDIT ON A LP RECORDED
TAPE>
<CHECK TAPE’S ERASE PROTECTION
TAB>
If the aspect ratio of the video you are playing is
strange, change the setting in “16:9 OUTPUT”.
(੬ pg. 34, 35)
<CANNOT EDIT ON A BLANK PORTION>
● Appears if Insert Editing is attempted on a tape
recorded in the LP mode. (੬ pg. 45)
● Appears if INSERT ( ) on the remote control is
pressed when the erase protection tab is set to
“SAVE”. (੬ pg. 45)
The remote control does not work.
● “REMOTE” is set to “OFF”.
● Appears if Insert Editing is attempted on a blank
portion of a tape. (੬ pg. 45)
➜Set “REMOTE” to “ON”. (੬ pg. 34)
● The remote control does not point at the remote
sensor.
➜Point at the remote sensor. (੬ pg. 24)
● The remote control batteries are exhausted.
➜Replace the batteries with fresh ones.
(੬ pg. 24)
MEMORY IS FULL
Appears when the memory card’s memory is full
and shooting is not possible.
SET DATE/TIME!
● Appears when the date/time is not set.
(੬ pg. 15).
● The built-in clock battery has run out and the
previously set date/time has been erased.
➜Consult your nearest JVC dealer for
replacement.
Displays the battery remaining power.
Remaining power level
High
Exhausted
As the battery power comes close to nil, the
battery remaining power indicator blinks.
When the battery power is exhausted, power turns
off automatically.
UNIT IN SAFEGUARD MODE
DC PLUG
TAPE END
Error indications 01, 02 or 06.
Remedy: Remove and reattach the power supply
or battery.
Appears when the tape ends during recording or
playback.
LENS CAP
UNIT IN SAFEGUARD MODE
EJECT AND REINSERT TAPE
Appears for 5 seconds after power is turned on if
the lens cap is attached or when it is dark.
Error indications 03 or 04.
Remedy: Eject the cassette and reinsert.
A. DUB ERROR!
In the above 2 error indications, the camcorder
turns off automatically. Eject the cassette once
and re-insert it, then check if the indication clears.
When it does, you can resume using the
camcorder. If the indication remains, consult your
nearest JVC dealer.
<CANNOT DUB ON A LP RECORDED
TAPE>
<CANNOT DUB ON A 16BIT RECORDING>
<CHECK TAPE’S ERASE PROTECTION
TAB>
● Appears if Audio Dubbing is attempted on a
blank portion of a tape. (੬ pg. 45)
● Appears if Audio Dubbing is attempted on a
tape recorded in the LP mode. (੬ pg. 45)
● Appears if Audio Dubbing is attempted on a
tape recorded in 16-BIT audio. (੬ pg. 45)
CAUTIONS
EN
48
AC Adapter
The Benefits Of Lithium-Ion Batteries
Lithium-ion battery packs are small but have
a large power capacity. However, when one is
exposed to cold temperatures (below 10°C/
50°F), its usage time becomes shorter and it
may cease to function. If this happens, place
the battery pack in your pocket or other
warm, protected place for a short time, then
re-attach it to the camcorder.
When using the AC Adapter in areas other
than the USA
The provided AC Adapter features automatic
voltage selection in the AC range from 110V to
240 V.
USING HOUSEHOLD AC PLUG ADAPTER
In case of connecting the unit’s power cord to an
AC wall outlet other than American National
Standard C73 series type use an AC plug
adapter, called a “Siemens Plug”, as shown.
For this AC plug adapter, consult your nearest
JVC dealer.
NOTES:
● It is normal for the battery pack to be warm after
charging, or after use.
Temperature Range Specifications
Charging: 10°C to 35°C (50°F to 95°F)
Operation: 0°C to 40°C (32°F to 104°F)
Storage: –20°C to 50°C (–4°F to 122°F)
● The lower the temperature, the longer
recharging takes.
Plug adapter
● Charging times are for a fully discharged battery
pack.
Battery Packs
The supplied battery pack is
a lithium-ion battery. Before
using the supplied battery
pack or an optional battery
pack, be sure to read the
following cautions:
● To avoid hazards
...do not burn.
...do not short-circuit the terminals. When
transporting, make sure the provided battery
cap is attached to the battery. If the battery cap
is misplaced, carry the battery in a plastic bag.
...do not modify or disassemble.
...do not expose the battery to temperatures
exceeding 60°C (140°F), as this may cause the
battery to overheat, explode or catch fire.
...use only specified chargers.
Terminals
Cassettes
To properly use and store your cassettes, be
sure to read the following cautions:
● During use
...make sure the cassette bears the Mini DV
mark.
...be aware that recording onto prerecorded
tapes automatically erases the previously
recorded video and audio signals.
...make sure the cassette is positioned properly
when inserting.
...do not load and unload the cassette repeatedly
without allowing the tape to run at all. This
slackens the tape and can result in damage.
...do not open the front tape cover. This exposes
the tape to fingerprints and dust.
● Store cassettes
...away from heaters or other heat sources.
...out of direct sunlight.
...where they won’t be subject to unnecessary
shock or vibration.
...where they won’t be exposed to strong
magnetic fields (such as those generated by
motors, transformers or magnets).
...vertically, in their original cases.
● To prevent damage and prolong service
life
...do not subject to unnecessary shock.
...charge in an environment where temperatures
are within the tolerances shown in the chart
below. This is a chemical reaction type
battery — cooler temperatures impede
chemical reaction, while warmer temperatures
can prevent complete charging.
...store in a cool, dry place. Extended exposure
to high temperatures will increase natural
discharge and shorten service life.
...fully charge and then fully discharge the battery
every 6 months when storing the battery pack
over a long period time.
...remove from charger or powered unit when not
in use, as some machines use current even
when switched off.
CAUTIONS
...in places subject to soot or steam such as near
a cooking stove.
EN
49
Memory Cards
To properly use and store your memory cards,
be sure to read the following cautions:
● During use
...make sure the memory card bears the SD or
MultiMediaCard mark.
...make sure the memory card is positioned
properly when inserting.
● While the memory card is being
accessed (during recording, playback,
deletion, initialization, etc.)
...never unload the memory card and never turn
off the camcorder.
● Store memory cards
...away from heaters or other heat sources.
...out of direct sunlight.
...where they won’t be subject to unnecessary
shock or vibration.
...in places subject to excessive shock or
vibration.
...near a television set.
...near appliances generating strong magnetic or
electric fields (speakers, broadcasting
antennas, etc.).
...in places subject to extremely high (over 40°C
or 104°F) or extremely low (under 0°C or 32°F)
temperatures.
● DO NOT leave the unit
...in places of over 50°C (122°F).
...in places where humidity is extremely low
(below 35%) or extremely high (above 80%).
...in direct sunlight.
...in a closed car in summer.
...near a heater.
● To protect the unit, DO NOT
...allow it to become wet.
...drop the unit or strike it against hard objects.
...subject it to shock or excessive vibration during
transportation.
...keep the lens directed at extremely bright
objects for long periods.
...expose the lens and viewfinder’s lens to direct
sunlight.
...carry it by holding the LCD monitor or the
viewfinder.
...swing it excessively when using the hand strap
or the grip.
...swing the soft camera case excessively when
the camcorder is inside it.
● Dirty heads can cause the following
problems:
...where they won’t be exposed to strong
magnetic fields (such as those generated by
motors, transformers or magnets).
LCD Monitor
● To prevent damage to the LCD monitor,
DO NOT
...push it strongly or apply any shocks.
...place the camcorder with the LCD monitor on
the bottom.
● To prolong service life
...avoid rubbing it with coarse cloth.
● Be aware of the following phenomena for
LCD monitor use.These are not
malfunctions
...While using the camcorder, the surface around
the LCD monitor and/or the back of the LCD
monitor may heat up.
...If you leave power on for a long time, the
surface around the LCD monitor becomes hot.
...No picture during playback.
Main Unit
● For safety, DO NOT
...Blocks of noise appear during playback.
...During recording or playback, the Head Clog
Warning indicator “ ” appears.
...open the camcorder’s chassis.
...disassemble or modify the unit.
...short-circuit the terminals of the battery pack.
Keep it away from metallic objects when not in
use.
...allow inflammables, water or metallic objects to
enter the unit.
...remove the battery pack or disconnect the
power supply while the power is on.
...leave the battery pack attached when the
camcorder is not in use.
...Recording cannot be performed properly.
In such cases, use an optional cleaning
cassette. Insert it and play back. If the cassette
is used more than once consecutively, damage
to the video heads may result. After the
camcorder plays back for about 20 seconds, it
stops automatically. Also refer to the cleaning
cassette’s instructions.
If, after using the cleaning cassette, the
problems still exist, consult your nearest JVC
dealer.
● Avoid using the unit
...in places subject to excessive humidity or dust.
CAUTIONS
EN
Mechanical moving parts used to move the
video heads and video tape tend to become
dirty and worn out over time. In order to
50
Declaration of Conformity
Model Number
Trade Name
Responsible party : JVC AMERICAS
CORP.
Address
: GR-D790U
: JVC
maintain a clear picture at all times, periodic
check-ups are recommended after using the
unit for about 1,000 hours. For periodic check-
ups please consult your nearest JVC dealer.
: 1700 Valley Road
Wayne, N. J. 07470
Telephone Number : 973-317–5000
This device complies with Part 15 of FCC
Rules. Operation is subject to the following
two conditions: (1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
How To Handle A CD-ROM
● Take care not to soil or scratch the mirror
surface (opposite to the printed surface). Do not
write anything or put a sticker on either the front
or back surface. If the CD-ROM gets dirty, gently
wipe it with a soft cloth outward from the center
hole.
● Do not use conventional disc cleaners or
cleaning spray.
● Do not bend the CD-ROM or touch its mirror
surface.
Changes or modifications not approved by
JVC could void the user’s authority to operate
the equipment. This equipment has been
tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed
to provide reasonable protection against
harmful interference in a residential
installation. This equipment generates, uses,
and can radiate radio frequency energy and,
if not installed and used in accordance with
the instructions, may cause harmful
● Do not store your CD-ROM in a dusty, hot or
humid environment. Keep it away from direct
sunlight.
About moisture condensation
● You have observed that pouring a cold liquid
into a glass will cause drops of water to form
on the glass’ outer surface. This same
phenomenon occurs on the head drum of a
camcorder when it is moved from a cool place
to a warm place, after heating a cold room,
under extremely humid conditions or in a place
directly subjected to the cool air from an air
conditioner.
interference to radio communications.
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does cause
harmful interference to radio or television
reception, which can be determined by
turning the equipment off and on, the user is
encouraged to try to correct the interference
by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the
equipment and receiver.
● Moisture on the head drum can cause severe
damage to the video tape, and can lead to
internal damage to the camcorder itself.
CONDENSATION, OPERATION
PAUSED PLEASE WAIT
Appears if condensation occurs. When this
indication is displayed, wait more than 1
hour until condensation disappears.
Connect the equipment into an outlet on a
circuit different from that to which the
receiver is connected.
Serious malfunctioning
Consult the dealer or an experienced radio/
TV technician for help.
If malfunctioning occurs, stop using the unit
immediately and consult your local JVC
dealer.
This Class B digital apparatus complies with
Canadian ICES-003.
Cet appareil numérique de la classe B est
conforme à la norme NMB-003 du Canada.
The camcorder is a microcomputer-controlled
device. External noise and interference (from
a TV, a radio, etc.) might prevent it from
functioning properly. In such cases, first
disconnect its power supply unit (battery
pack, AC Adapter, etc.) and wait a few
minutes and then re-connect it and proceed
as usual from the beginning.
SPECIFICATIONS
EN
51
Camcorder
For Digital Video Camera
Format
For General
Power supply
DC 11 V (Using AC Adapter)
DC 7.2 V (Using battery pack)
Power consumption
Approx. 2.2 W (2.3 W*) (LCD monitor off,
viewfinder on)
Approx. 2.7 W (2.8 W*) (LCD monitor on,
viewfinder off)
DV format (SD mode)
Signal format
NTSC standard
Recording/Playback format
Video: Digital component recording
Audio: PCM digital recording, 32 kHz 4-channel
(12-BIT), 48 kHz 2-channel (16-BIT)
Cassette
Mini DV cassette
Tape speed
SP: 18.8 mm/s, LP: 12.5 mm/s
Maximum recording time (using 80 min.
cassette)
Approx. 7.5 W (Maximum; when charging the
battery pack)
*
Using LED Light
Dimensions (W x H x D)
61 mm x 94 mm x 114 mm (2-3/8" x 3-11/16" x
4-1/2") (with the LCD monitor closed and the
viewfinder pushed back in)
Weight
SP: 80 min., LP: 120 min.
For Digital Still Camera
Storage media
SD Memory Card/MultiMediaCard
Compression system
JPEG (compatible)
File size
Still image:
640 x 480 pixels
Approx. 410 g (0.90 lbs) (without battery, cassette
and lens cap)
Approx. 480 g (1.06 lbs) (incl. battery, cassette
and lens cap)
Operating temperature
0°C to 40°C (32°F to 104°F)
Operating humidity
Picture quality
2 modes (FINE/STANDARD)
Approximate number of storable images
੬ pg. 26
35% to 80%
Storage temperature
–20°C to 50°C (–4°F to 122°F)
Pickup
1/6" CCD
For Connectors
Lens
AV
F 2.0, f = 2.3 mm to 78.2 mm, 34:1 power zoom
lens
Filter diameter
Video output: 1.0 V (p-p), 75 Ω, analog
Audio output: 300 mV (rms), 1 kΩ, analog, stereo
DV
ø27 mm
LCD monitor
Input/output: 4-pin, IEEE1394 compliant
USB
2.7" diagonally measured, LCD panel/TFT active
Mini USB-B type, USB 1.1 compliant
matrix system
Viewfinder
Electronic viewfinder with 0.33" color LCD
Speaker
Monaural
LED Light
Effective distance: 1.5 m (5 ft)
AC Adapter
Power requirement
AC 110 V to 240 V~, 50 Hz/60 Hz
Output
DC 11 V =, 1 A
Specifications shown are for SP mode unless
otherwise indicated. E & O.E. Design and
specifications subject to change without notice.
TERMS
Insert Editing ................. 45
Iris Lock ......................... 38
A
S
AC Adapter ....................14
Audio Dubbing ...............45
Auto/Manual Mode ........20
Shutter Effects ...............41
J
Journalistic Shooting ..... 19
B
Backlight Compensation 39
Battery Pack ......13, 14, 48
Blank Search .................22
Bright .................15, 34, 35
L
............................ 8, 15
C
Time Code .........20, 34, 35
Tripod Mounting .............15
Cam Reset .....................34
Changing The Menu
Settings ...........31 – 35
Charging The Battery Pack
.................................13
Clock Adj. ..........15, 34, 35
Connection To A Personal
Computer ................44
Connections To A TV Or
VCR ........................23
Control Level ...................7
M
Manual Focus ............... 37
Melody .......................... 34
N
W
Night Alive ..................... 41
Wind Cut ........................33
D
O
Data Battery ...................14
Date/Time Settings ........15
Deleting Files .................29
Demonstration Mode .....34
Digital Image Stabilization
(DIS) .......................32
P
Playback Sound ............ 35
Playback Special Effects 25
Power-linked operation ... 8
Priority ........................... 34
Program AE .................. 41
Protecting Files ............. 28
16:9 Output ..............34, 35
Digital Still Camera ........26
DPOF Setting (Digital Print
Order Format) ...29, 30
Dual Cam .......................20
Dubbing ...................41, 43
Q
E
Quick Review ................ 18
Effects ............................41
Exposure Control ...........38
R
Rec Mode ................ 33, 35
Recording Capacity
G
Memory Card ......... 26
Tape ....................... 18
Recording Media Selection
................................ 33
Remote Control ....... 24, 34
Resetting The File Name 28
Gain Up .........................33
I
Image Size .....................33
Index Playback ..............27
Initializing A Memory Card
.................................30
Printed in Malaysia
US
© 2006 Victor Company of Japan, Limited
1106ASR-NF-MP
|