Jensen VM9414 User Manual

Installation Guide  
VM9414  
What’s in the Box  
VM9414 Head Unit  
Single DIN Sleeve  
Wiring Harness  
Cosmetic Trim Ring  
Remote Control with Battery  
3.5mm to 3.5mm Media Adaptor Cable  
Owners Manual  
Parking Brake Sensor Extension Wire  
Mounting Hardware  
Installation Guide  
Tools and Supplies  
You will need these tools and supplies to install your VM9414:  
Torx type, at-head and Philips screwdrivers  
Wire cutters and strippers  
Tools to remove existing radio (screwdriver, socket wrench set or other tools)  
Electrical tape  
Crimping tool  
Volt meter/test light  
Crimp connections  
18 gauge wire for power connections  
16 – 18 gauge speaker wire  
WARNING! Never install this unit where operation and viewing could interfere with safe driving  
conditions.  
1
Wiring  
WARNING! Only connect the unit to a 12-volt power supply with proper grounding.  
Complete wiring as illustrated in the wiring diagram on page 4. Once the wiring is complete, reconnect the bat-  
tery negative terminal. If there is no ACC available, connect the ACC lead to the power supply with a switch.  
NOTE: When replacing a fuse, be sure to use correct type and amperage to avoid damaging the radio. The  
VM9414 uses one 15 amp fuse, located in the black lter box in-line with the main wire harness.  
Final Installation  
After completing the wiring connections, turn the unit on to conrm operation (ignition switch must be on). If  
unit does not operate, recheck all wiring until problem is corrected. Once proper operation is achieved, turn off  
the ignition switch and proceed with nal mounting of the chassis.  
Connect wiring adapter to existing wiring harness.  
1
4
5
Connect antenna lead.  
2
1
Carefully slide the radio into the mounting sleeve, making  
3
sure it is right-side-up, and secure with the original 4 screws.  
Attach one end of the perforated support strap (supplied) to  
4
2
Press  
A
udio  
the screw stud, which is screwed into the threaded insert on  
the back of the unit, using the hex nut provided. Fasten the  
other end of the perforated strap to a secure part of the  
dashboard either above or below the radio using the screw  
and hex nut provided. Bend the strap to position it as  
necessary.  
VM9414  
VO  
L
MUTE  
NA  
V
Enter  
AV  
IN  
SE  
L
3
CAUTION! The rear of the radio must be  
supported with the strap to prevent dam-  
age to the dashboard from the weight of  
the radio or improper operation due to  
vibration.  
Replace any items you removed from the dashboard.  
5
ISO-DIN Installation  
NOTE: For proper operation of the CD/  
DVD player, the chassis must be mounted  
within 20° of horizontal. Make sure the unit  
is mounted within this limitation.  
Remove mounting sleeve brackets.  
1
Remove trim ring.  
2
Mount factory brackets on new radio using existing screws  
from old radio.  
3
En  
ter  
AV  
IN  
SEL  
Slide radio chassis into dash opening and secure.  
Remove Mounting  
Sleeve Brackets  
4
Re-install dash panel.  
5
LOC  
P
r
e
s
s
S
T
A
udio  
VM9414  
REP  
LOUD  
VOL  
M
UTE  
E
nter  
AV  
IN  
SEL  
3
Wiring Diagram  
IMPORTANT: Incorrect wiring connections can damage the unit. Follow the wiring instructions carefully, or  
have the installation handled by an experienced technician.  
For basic iPod connectivity, you can use the white 30-pin to USB iPod cable that came with your Apple device.  
For iPod video playback, you must purchase the jLink-USB cable. Connect the iPod cable to the MediaLink  
USB and route the MediaLink USB to an accessible part of the dash area for easy connectivity. For occasional  
iPod use, keep an iPod cable in your glove box and use it to connect the iPod to the front USB connector.  
Bluetooth Connector  
(Connect to optional BTM10)  
MULTIZONE  
LCH  
MONITOR  
1
MULTIZONE  
RCH  
Additional Monitors  
Sold Separately  
REAR  
MONITOR 2  
MONITOR  
2
Need Help?  
jLink USB iPod Interface Cable  
(Sold Separately) - Required for iPod  
Video Viewing through Head Unit  
REAR  
MONITOR 1  
For technical assis-  
tance, call the Jensen  
customer support line  
at 1-800-323-4815.  
Backup Camera  
Sold Separately  
GPS  
Antenna  
CAMERA  
AUX IN  
VIDEO  
AUX IN/L  
AUX IN/R  
MediaLink  
USB (included)  
NOTE: Steering Wheel Control (SWC)  
Requires PAC SWI-PS Interface  
Adapter, Sold Separately  
SWC  
PINK  
PARKING BRAKE  
PARKING  
XM L  
Connect to optional XM  
Satellite Radio Receiver  
with Antenna  
XM R  
XM RADIO  
USB BUS  
Harness Cord  
LINE OUT  
FRONT R  
P
R
N
D
2
External  
Power Amplifier  
LINE OUT  
FRONT L  
L
Ground  
GREEN/WHITE  
REVERSE +  
LINE OUT  
REAR R  
Gearbox  
Switch  
LINE OUT  
REAR L  
ACC  
RED  
Ignition Switch  
ACC  
LINE OUT  
SUBWOOFER  
BATTERY +  
Battery  
YELLOW  
BATT  
FUSE (15A)  
Car  
BLACK  
Ground  
BATTERY  
GND  
WHITE +  
WHITE/BLACK -  
FRONT L  
External power amplifier control  
BLUE/WHITE  
P.CONT  
GREY +  
Antenna  
Auto antenna control (connect to antenna  
control lead & power supply of antenna  
amplifier)  
GREY/BLACK -  
FRONT R  
REAR R  
REAR L  
BLUE  
PURPLE +  
P. ANT  
PURPLE/BLACK -  
Mute (leave open if not connected)  
BROWN  
MUTE  
Car  
Phone  
GREEN +  
ORANGE  
GREEN/BLACK -  
ILLUM  
4

Audiovox MOVIES 2 GO MMD850 User Manual
Blaupunkt COBURG RCM 127 User Manual
Canon X Mark I Mouse Slim 5565B002 User Manual
Canon zr10 User Manual
Dual WMA XDMA6370 User Manual
Fender 90 User Manual
Focal SOLID 2 User Manual
JBL GTO6527 User Manual
JVC Camcorder GR DVL815 User Manual
JVC Car Stereo System KD R618 User Manual