VM8022
Installation and Operation Manual
Watts Peak
Watts en Crête
Vatios el Máximo
40W x 4
VM8022
TABLE OF CONTENTS
Introduction ..............................................................................................1
Installation ................................................................................................1
Wiring .......................................................................................................3
Remote Control ........................................................................................4
Operation .................................................................................................5
Tuner Operation .......................................................................................7
Disc/MP3/WMA Playback ........................................................................8
System Setup Menu ...............................................................................10
USB/SD Operation .................................................................................12
Care and Maintenance ...........................................................................15
Troubleshooting .....................................................................................16
Specifications .........................................................................................17
i
VM8022
ii
VM8022
2. Remove Transport Screws
INTRODUCTION
Congratulations on your purchase of the Jensen VM8022 Mobile
Multimedia Receiver. It’s a good idea to read all of the instructions before
beginning the installation. We recommend having your Jensen VM8022
installed by a reputable installation shop.
TRANSPORT SCREWS
INSTALLATION
This unit is designed for installation in cars, trucks and vans with an existing
radio opening. In many cases, a special installation kit will be required to
mount the radio to the dashboard. These kits are available at electronics
supply stores and car stereo specialty shops. Always check the kit
application before purchasing to make sure the kit works with your vehicle.
If you have trouble locating a kit or need installation assistance, contact
Technical Support at 1-800-323-4815 from 8:30am to 7:00pm EST Monday
through Friday and from 9:00am to 5:00pm EST on Saturday.
Tools and Supplies
The following tools and supplies are needed to install the radio:
Universal Installation
1. Check the dashboard opening size by sliding the radio into it.
•
•
•
Torx type, flathead and Philips screwdrivers
Wire cutters and strippers
Tools to remove existing radio (screwdriver, socket wrench set or other
tools)
•
•
•
•
•
•
Electrical tape
Crimping tool
Volt meter/test light
Crimp connections
18 gauge wire for power connections
16-18 gauge speaker wire
Preparation
1. Disconnect Battery
If the opening is too small, carefully cut or file as necessary until the
radio easily slides into the opening. Do not force the radio into the open-
ing. Check for sufficient space behind the dashboard for the radio chas-
sis.
Before you begin, always disconnect the battery negative terminal.
NOTE: If the VM8022 is to be installed in a car equipped with an on-
board drive or navigation computer, do not disconnect the battery
cable. If the cable is disconnected, the computer memory may be lost.
Under these conditions, use extra caution during installation to avoid
causing a short circuit.
CAUTION: For proper operation of the DVD player, the chassis must
be mounted within 20° of horizontal. Make sure the unit is mounted
within this limitation.
2. Place the radio in front of the dashboard opening so the wiring can be
brought through. Follow the wiring diagram carefully and make certain
all connections are secure and insulated with wire nuts or electrical
tape. See “Wiring” on page 3. After completing the wiring connections,
1
VM8022
turn the unit on to confirm operation (vehicle ignition must be on). If the
unit does not operate, re-check all wiring until the problem is corrected.
3. Secure the rear of the unit to the car body using the mounting bolt and
rubber cushion.
mounting. Save all hardware and brackets as they may be used to
mount the new radio.
2. Carefully unsnap the plastic frame from the front of the new radio
chassis. Remove and discard the frame.
4. Test the radio using the “Operation” instructions that follow.
3. Remove the factory mounting brackets and hardware from the existing
radio and attach them to the new radio. Do not exceed M5 x 9mm
maximum screw size. Longer screws may damage components inside
the chassis.
4. Wire the new radio as outlined in the Universal Installation instructions.
5. Mount the new radio assembly to the dashboard or center console
using the reverse procedure of step 1.
Fuses
When replacing a fuse, make sure the new fuse is the correct type and
amperage. Using an incorrect fuse could damage the radio.
RUBBER CUSHION
MOUNTING BOLT
RADIO
Reconnect Battery
When wiring is complete, reconnect the battery negative terminal.
Technical Assistance
If you require assistance, contact Technical Support at 1-800-323-4815
from 8:30am to 7:00pm EST Monday through Friday and from 9:00am to
5:00pm EST on Saturday.
TRIM RING
Kit Installation
If your vehicle requires the use of an installation kit to mount this radio,
follow the instructions included with the installation kit to attach the radio to
the mounting plate supplied with the kit.
1. Wire and test the radio as outlined in the Universal Installation instruc-
tions.
2. Install the radio/mounting plate assembly to the sub-dashboard
according to the instructions in the installation kit.
3. Replace the dashboard trim panel.
ISO Installation
This unit has threaded holes in the chassis
side panels which may be used with the
original factory mounting brackets of some
vehicles to mount the radio to the
dashboard. Please consult with your local
car stereo shop for assistance on this type
of installation.
1. Remove the existing factory radio
from the dashboard or center console
2
VM8022
WIRING
Parking
(Blue)
(Yellow)
(Yellow)
Fuse (15A)
NOTE: The amplifier in this
radio is only designed for use with
four speakers. Never combine
(bridge) outputs for use with two
speakers. Never ground negative
speaker leads to chassis ground.
Failure to wire exactly as shown
may cause electrical damage to the
radio.
A/V Media
Adapter Cable
Ground
Connect to ground terminal
or clean, unpainted part of chassis.
Power Antenna
Connect to power antenna or amplifier.
If not used, tape bare end of wire.
Black
Blue
NOTE: Only connect speakers with
a nominal impedance of 4 ohms.
Speakers with a load
impedance less than 4 ohms
could damage the unit.
Memory/Battery
Connect to battery or 12 volt power
source that is always live. The radio will
not work if this wire is not connected.
Accessory/Ignition
Connect to existing radio wire
or radio fuse.
Yellow
Red
IMPORTANT!
FRONT SP
Gray
REAR SP
The pink parking wire MUST
be connected to the switched
side of the parking break
circuit (the part that becomes
grounded when the brake is
applied).
White/Black
Stripe
White Gray/Black
Stripe
Green/Black
Stripe
Green Purple/Black
Stripe
Purple
Left Speaker
(Front)
Right Speaker
(Front)
Left Speaker
(Rear)
Right Speaker
(Rear)
3
VM8022
REMOTE CONTROL
The remote control will allow you to control the advanced functions of the
VM8022.
Operating Range
The remote control sensor (19) is located to
the right of the power button. The remote
control can operate within a distance of 3~5m.
REMOTE SENSOR
1. ZOOM (DVD, VCD only)
2. TITLE (DVD only)
3. Power On/Off
4. SETUP: Access DVD Setup
5. Menu Navigation
6. ENTER
7. PROG: Enter Programmed
Playback mode.
8. Direct Number Entry
9. SEL
Replacing the Battery
When the range of operation of the card
remote control becomes short or stops
functioning, replace the battery with a new
lithium battery. Be sure to observe the proper
polarity, as indicated below.
(CR 2025)
•
Audio Mode: Select BAS,
TRE, BAL, FAD.
•
Press and hold for System
Menu
10. Volume Control
11. Mute
12. SEEK
2
1
•
•
Radio Tune
Track Skip/Seek
13. SUB.T: Subtitle (DVD only)
14. SRC: Change Input Source
15. REPEAT
16. A-B Repeat
17. Stop/Return
18. Play/Pause
19. GOTO Search
20. MENU PBC
•
•
DVD Menu
PBC (for VCD 2.0 and up)
21. OSD: On Screen Display
22. AUDIO
•
•
DVD Audio
VCD Audio L/R/ST
23. DISP: View On Panel Display
24. ANGLE (DVD only)
25. BAND/P/N
•
•
Video System: PAL, NTSC, AUTO
Radio Band
4
VM8022
OPERATION
Power
•
•
BALANCE: Turn the rotary encoder to adjust the balance from “R7” (full
right) to “L7” (full left).
FADER: Turn the rotary encoder to adjust the fader from “F7” (full front)
to “R7” (full rear).
Press the (power) button (2) to turn the unit on. Press and hold the power
button again to turn the unit off.
The unit automatically exits the audio control menu after five seconds of
inactivity.
NOTE: LCD panels may take longer to respond when subjected to cold
temperatures for an extended period of time. In addition, the visibility
of the numbers on the LCD may decrease slightly. The LCD display
will return to normal when the temperature becomes normal.
18
20
Source
Press the SRC button (6) to select a different mode of operation, as
indicated on the display panel. Available modes include tuner (FM1, FM2,
FM3, AM1, AM2), DVD, SD, USB, and auxiliary (AUX).
VM8022
22
LOUD
21
Audio Mute
Press the MUTE button (21) to silence the audio volume. “ ” appears on
VOL
the display. Press MUTE again to restore volume to the previous setting.
AS
Volume Control
To increase the volume, turn the rotary encoder (5) clockwise. To decrease
the volume, turn the rotary encoder counter-clockwise. When volume is
adjusted, the volume level will be shown on the display panel as a number
ranging from “0” (lowest) to “63” (highest).
SD/MMC
/
1
6
INT
2
5
RPT
RDM
3
4
Audio Menu
Press the VOL button (5) to access the audio menu. Press the VOL button
23
repeatedly to move through the list of menu options.
Menu Operation
Press and hold the VOL button (5) for more than two seconds to access the
menu. Press the VOL button to move through the following menu options:
EQ MODE, BEEP, 12/24 MODE (clock), VOL MODE, A-VOL,
SUBWOOFER, SUB VOL. The following procedures assume you have
already accessed the menu.
VOL
Equalizer Selector (EQ MODE)
The equalizer function applies preset sound effects to the unit’s audio
output signal. Turn the rotary encoder to select from the following equalizer
options: “OFF”, “ROCK”, “POP”, “CLASSIC” and “FLAT”. With the equalizer
function activated, if bass or treble is adjusted, the EQ Mode will revert to
OFF.
•
•
BASS: Turn the rotary encoder (5) to adjust the bass level from “+7” to
“-7”.
TREBLE: Turn the rotary encoder to adjust the treble level from “+7” to
“-7”.
5
VM8022
When the equalizer function is activated, the most recently selected bass/
treble levels cannot be adjusted. When the equalizer function is not active,
the unit will return to the most recently selected bass and treble levels.
Loudness Control (LOUD)
When listening to music at low volumes, this feature will boost the bass and
treble ranges to compensate for the characteristics of human hearing.
Press the LOUD button (16) to activate this feature as indicated by “LOUD”
on the display panel. Press the LOUD button again to deactivate the
function. “LOUD” will disappear from the display.
BEEP
The beep tone feature allows the selection of an audible beep tone to be
heard each time the menu is accessed. “ON” is the default setting. Turn the
rotary encoder to select “OFF”.
Clock Set
12 / 24 MODE
1. Press the DISP button (7) to display the clock.
2. Press and hold the DISP button until the clock blinks.
3. Turn the rotary encoder (5) to set the minutes.
4. Press the VOL button (5) to confirm and move to the hour field.
5. Turn the rotary encoder to set the hour.
This option allows selection of a 12 hour or 24 hour clock format. “24
HOUR” is the default setting. Turn the rotary encoder (VOL control) to
change to the 12 hour clock format.
VOL-MODE
6. Press the DISP button to set the clock and exit the clock set function.
Turn the rotary encoder to select “VOL LAST” or “VOL ADJUST”.
Reset Button
•
VOL LAST: When the unit is turned on, the volume will resume at the
level selected when last turned off.
The RESET button (22) is located below the eject button. The reset circuitry
protects the microprocessor circuitry. Since resetting the unit will erase the
time and preset memories, it should only be activated upon initial
installation after all wiring is complete, or if there is a malfunction of any of
the switches on the unit. In these circumstances, pressing the RESET
button will clear the system and return the unit to normal operation.
•
VOL ADJUST: If choosing VOL ADJUST, use the A-VOL setting to
specify a turn-on volume.
Turn-On Volume (A-VOL)
After selecting “VOL ADJUST”, press the VOL button (5) to access the A-
VOL setting and then turn the rotary encoder to select the desired turn-on
volume level. When this option is selected, the unit will revert to the
adjusted volume each time the unit is turned on.
18
20
SUBWOOFER
After connecting a subwoofer to the back of the unit, turn the rotary encoder
to select a crossover frequency: 80, 100 or 120Hz.
VM8022
22
SUB VOL
LOUD
21
The SUB VOL control is only applicable if the unit is connected to an
optional sub-woofer speaker and is activated. To adjust the sub-woofer level
from “00” to “33”, press the VOL button (5) until “SUB VOL” appears in the
display. Turn the rotary encoder clockwise to increase or counter-clockwise
to decrease the subwoofer level.
VOL
AS
Local/Distant Reception (LO/DX)
SD/MMC
When the Local function is on, only radio stations with a strong signal are
played. To activate Local reception mode, press the LO/DX button (20).
“Local” will appear on the screen briefly. If pressed again, “DX” appears
briefly.
/
1
6
INT
2
5
RPT
RDM
3
4
23
6
VM8022
TUNER OPERATION
remaining five presets on the current band and for presets on the other four
bands.
18
20
STEREO
INDICATOR
VM8022
22
LOUD
21
VOL
AS
PRESET NUMBER
FM1: 98.10 MHZ 3
SD/MMC
/
1
6
INT
2
5
RPT
RDM
3
4
EQUALIZER
INDICATOR
23
Select a Band
LOUD SETTING INDICATOR
Press the BAND button (3) to change between three FM and two AM
bands. Each band stores up to six preset stations.
Tuning
Preset Scan
Manual Tuning
Press the AS button (14) to scan and play each preset station for 5 seconds
each. Press AS again to stop preset scan.
Press the TUNE/TRACK >>| or |<< buttons (17) to move the radio
frequency number up or down one step.
Automatic Preset Store
Seek Tuning
Press and hold the AS button (14) to select six strong stations and store
them in the current band using the AUTO PRESET feature. The radio will
automatically scan all bands and enter strong stations into the preset
memory positions. After entering the stations into memory, the unit will
automatically stop at each station for five seconds, allowing you to preview
each selection. When using the AUTO PRESET feature, the new stations
replace any stations already stored in preset memory.
Press and hold the TUNE/TRACK >>| or |<< buttons (17) for more than
three seconds to seek the next/previous station automatically.
Preset Stations
Up to six stations on each band can be stored as presets, which can then
be instantly recalled by pressing the associated preset button (8-13). To
store a station, turn the radio on and select the desired band and station.
Press and hold the desired preset button (numbered one through six on the
face of the radio) for more than two seconds. When stored, the preset
number will appear in the display. The station is now stored and can be
recalled by pressing the corresponding preset button. Repeat for the
NOTE: You can stop the AUTO PRESET function at any time by
pressing the AS button again.
7
VM8022
DISC/MP3/WMA PLAYBACK
Fast Forward/Reverse
18
20
Press and hold the TUNE/TRACK >>| or |<< buttons (17) to fast forward or
fast reverse. Press and hold once for 2X. Press and hold additional times
for 4X, 8X, 20X or PLAY. Press the play/pause >/|| button (8) to end fast
forward or reverse and resume normal playback.
VM8022
22
Intro Scan (INT)
LOUD
During disc play, press the INT button (9) to select “INTRO” and play the
first 15 seconds of each track/file. When the desired track is reached, press
INT again to end the scan and play the selected track.
21
VOL
Repeat (RPT)
AS
Press the RPT button (10) multiple times during playback to select from the
following repeat play options:
SD/MMC
•
•
•
VCD/CD: RPT ONE (track), RPT ALL (disc), RPT OFF
DVD: RPT CHAPTER, RPT TITLE, RPT OFF
MP3/WMA: RPT ONE (file), RPT DIR (directory/folder), RPT ALL (disc),
RPT OFF
/
1
6
INT
2
5
RPT
RDM
3
4
Random (RDM)
23
Press the RDM button (11) during playback to select “RANDOM” and play
all tracks/files in random, shuffled order. Press RDM again to stop random
play.
Insert and Eject Disc
Insert a disc, label side up, into the disc slot (18).
To stop disc play and eject the disc, press the eject button (4).
Section Repeat (A-B)
To repeat a specified section of a track, perform the following steps:
1. Press the A->B button on the remote control to select the starting point.
The display will show “REPEAT A-”.
2. Press A->B when you reach the desired ending point. The display
shows “REPEAT A-B” and the selected section will play repeatedly.
NOTE: The unit is designed for play of standard 5” (12 cm.) discs only.
Do not attempt to use 3” (8 cm.) CD singles in this unit, either with or
without an adaptor, as damage to the player and/or the disc may
occur. Such damage will not be covered by the warranty on this
product.
To cancel section repeat, press the A->B button again. “A-B CANCEL”
appears on the display.
Controlling Disc or File Playback
Pause
GOTO Direct Track Access
Use the GOTO function to access a track directly.
Press the pause >/|| button (8) to suspend playback. Press the pause >/||
button again to resume playback.
1. Press the GOTO button on the remote control. The track number will
become highlighted.
2. Use the number keys on the remote control to enter the track number
directly.
Track Select
Press the TUNE/TRACK >>| or |<< buttons (17) for less than one second to
advance to the next track/file. The selected track number will appear on the
display.
3. Press the ENTER button to confirm and begin playback.
8
VM8022
Programmed Playback
•
TITLE: Press to display the title or chapter list. Use the
,
,
or
cursor buttons or the numeric buttons to enter a title or chapter number,
and then press ENTER to play.
1. Press the PROG button on the remote control to access the pro-
grammed playback screen:
•
•
ANGLE: Press to select an alternate viewing angle, if available.
ZOOM: Press to zoom the picture at X2, X3, X4, X1/2, X1/3 or X1/4, or
select OFF to return to normal view.
NOTE: Feature availability is dependent upon DVD embedded
information.
Disc Player Error Codes
If a problem should develop while operating the Disc player, an error code
may appear on the display panel. This can indicate a number of problems
with the unit, including a mechanical error or an error in the microprocessor
control. If an error code appears, try ejecting and reloading the disc into the
player. While the disc is out of the unit, make sure it is clean and
2. Use the
,
,
or cursor buttons to access the fields on the
“PROG” screen.
undamaged, and then load it correctly. If this does not solve the problem,
pressing the RESET button (22) may help, but will erase the time and
preset memory. If the suggested measures do not solve the problem,
contact an approved warranty station near you for further assistance.
3. Use the number buttons on the remote control to enter a track number
in each field.
18
20
4. Press the >/|| button (8) or highlight “PLAY” on screen and then press
ENTER to begin playback in the numbered order indicated.
To delete the list, highlight “CLEAR” and then press ENTER. Press PROG
to exit the programmed playback screen.
VM8022
22
VCD PlayBack Control (VCD Only)
LOUD
21
If you insert a VCD with playback control, playback automatically starts at
the beginning of the first track.
VOL
•
•
Press the PBC button on the remote control to access the VCD menu.
Use the TUNE/TRACK >>| or |<< buttons (17) to select the desired
track.
AS
•
•
Press the (stop) button to return to the menu.
Press PBC again to exit the menu.
SD/MMC
/
1
6
INT
2
5
RPT
RDM
3
4
DVD Playback Features
The following remote control features are available during DVD playback:
•
•
AUDIO: Press to choose an alternate audio language, if available.
SUB-T: Press to select an alternate subtitle language, if available.
23
9
VM8022
SYSTEM SETUP MENU
Table 1: System Setup Menu
During disc play, press the SETUP button on the remote control to access
the SYSTEM SETUP menu.
ASPECT RATIO
4: 3 PS
With 16:9 display, the left
and right sides are cut
off.
SYSTEM LANGUAGE VIDEO
4:3 LB
16:9
With 16:9 display, the
top and bottom are cut
off.
Image is presented in
wide view with a 16:9
aspect ratio.
VIDEO FORMAT
SCREEN SAVER
ASPECT RATIO
PASSWORD
RATING
PASSWORD
RATING
_ _ _ _
Enter a 4-digit password
to activate the “Rating”
feature. The original
password is “0000”.
1 KID SAFE
2 G
Select the appropriate
rating level for the
intended audience.
DEFAULT
EXIT SETUP
3 PG
You may override higher
ratings by using your
password.
4 PG13
5 PG-R
6 R
Use the
,
,
or cursor buttons to choose between SYSTEM,
LANGUAGE, or VIDEO setup options.
7 NC-17
8 ADULT
RESTORE
Table 1: System Setup Menu
SYSTEM SETUP
DEFAULT
Select “Reset” to restore
the factory default set-
tings for the Rating sys-
tem only.
VIDEO FORMAT
NTSC
PAL
The color signals are
output in the standard
NTSC format.
LANGUAGE SETUP
The color signals are
output in the standard
PAL format.
OSD LANGUAGE
ENGLISH
GERMAN
SPANISH
FRENCH
Select the appropriate
on-screen language for
the DVD
AUTO
The color signal output
is switched automatically
based on the current
video input signal -
NTSC or PAL.
SCREEN SAVER
ON
Turn screen saver on/off.
OFF
10
VM8022
Table 1: System Setup Menu
AUDIO LANGUAGE
ENGLISH
Choose from audio lan-
guages contained on the
DVD If you are watching
a disc recorded in multi-
ple languages
FRENCH
SPANISH
PORTUGUESE
GERMAN
NOTE: Languages are
DVD dependent and not
all languages may be
supported.
SUBTITLE LANG
ENGLISH
Choose the language
you would like subtitles
to appear in (if available)
FRENCH
SPANISH
NOTE: Subtitles are
DVD dependent and not
all languages may be
supported..
PORTUGUESE
GERMAN
OFF
Turn subtitles off
MENU LANG
ENGLISH
FRENCH
SPANISH
PORTUGUESE
GERMAN
Select the default lan-
guage in which you
would like the DVD
menu (if applicable) to
be displayed.
VIDEO SETUP
BRIGHTNESS
CONTRAST
HUE
12 - 0
12 - 0
+6 to -6
12 - 0
8 - 0
Use the
/
cursor but-
tons to set the video out-
put options
SATURATION
SHARPNESS
EXIT SETUP
11
VM8022
USB/SD OPERATION
Notes on MP3/WMA Play
•
•
Maximum number of files per disc: 999
Maximum number of folders per disc: 255
MP3 and WMA (Windows Media Audio) music files are digital audio files
that are compressed to allow more files on a single CD. This unit can play
MP3/WMA directly from files contained on a CD-R/RW or an SD card, USB
Device using the buttons on the receiver (or remote control) as described
below.
MP3/WMA files written in formats other than those listed above will not play
successfully and their file or folder names will not display properly.
MP3/WMA Encoder and CD Writer Settings
Use the following settings when compressing audio data with the MP3
encoder.
Many types of software are available for converting audio files into MP3/
WMA formats. Jensen recommends Nero or Roxio Easy CD Creator.
•
•
Transfer bit rate: 8 - 320 kbps
Sampling frequency: 8, 11.025, 12, 16, 22.05, 24, 32, 44.1, 48 kHz
This unit can play MP3 (MPEG1, 2, 2.5 Audio Layer 3). However, the MP3
recording media and accepted formats are limited. When writing MP3/
WMA, pay attention to the following restrictions.
When using a CD writer to record MP3/WMA up to the maximum disc
capacity, disable additional writing. To record an empty disc up to the
maximum capacity at once, select the “disc at once” option.
Acceptable Media
The MP3/WMA recording media acceptable to this unit are CD-ROM, CD-
R, and CD-RW. The unit will also play MP3, WMA, photo or videos files
written to SD Cards, USB Devices.
Entering ID3 Tag
This unit supports ID3 tag version 2.0.
For character codes, refer to the table to
the right.
Depending on the media type and recording method, some CD-R/RWs may
be incompatible with this unit. When using CD-RW, use full format rather
than quick format to prevent malfunction.
Entering File and Folder Names
Names using the code list characters
are the only file names and folder
names that can be entered and
displayed. Using any other character will
cause the file and folder names to be
displayed incorrectly. The unit
This unit supports playback of MP3/WMA and CDDA (CDA), Mixed-Mode
CDs and CD-Extra (including multi-session discs). Discs on which the
session has not been closed will not play.
NOTE: This unit supports FAT 16 and FAT 32 file systems. The unit
supports USB 1.1 only, but will play USB 2.0 devices at USB 1.1 speed.
recognizes and plays only files with the MP3/WMA extension.
Acceptable Medium Formats
NOTE: A file name entered with characters not on the code list may
not play correctly.
The following formats are available for the media used in this unit. The
maximum number of characters used for file name, including the delimiter
(".") and three-character extension, are indicated in parentheses.
Electronic Shock Protection
•
•
•
•
ISO 9660 Level 1 (11 characters)
ISO 9660 Level 2 (31 characters)
Joliet (31 characters)
•
•
•
10 seconds for CD-DA (CDA)
>45 seconds for MP3 recorded at 44.1kHz, 128kbps
>90 seconds for WMA recorded at 44.1kHz, 128kbps
Romeo (31 characters)
Bit Rates
Up to 200 characters can be displayed in the long file name format. For a
list of available characters, see the instruction manual of the writing
software and the section “Entering File and Folder Names” that follows. The
media reproducible on this unit has the following limitations:
The unit supports bit rates from 32 - 320 kbps.
•
Maximum number of nested folders: 8
12
VM8022
MP3 Playing Order
Loading an SD Card
Insert the SD card into the SD slot (15) on the front of the radio. The unit will
read the files on the card automatically.
When selected for play, files and folders (Folder Search, File Search or
Folder Select) are accessed in the order in which they were written to the
media. As a result, the order in which they are expected to be played may
not match the order in which they are actually played. You may be able to
set the order in which MP3/WMA files are to be played by assigning file
names beginning with play sequence numbers such as "01" to "99". For
example, a medium with the following folder/file hierarchy is subject to
Folder Search, File Search or Folder Select as shown below.
To remove the card, first press the SRC button (6) to switch to another
mode and stop SD playback. Press the SD card to pop it out, then remove
the card.
Loading a USB Device
1. Locate the USB jack (23) located near the bottom right corner on the
front of the radio.
2. Pull the left side to lift the rubber cover and reveal the USB jack.
3. Insert the USB device into the USB jack. The unit will read the files on
the USB device automatically.
The VM8022 player will only recognize three folder levels and does not
display folders containing only other folders. In the example above, the unit
will display folders 3, 4, 6, and 8, but not 2 and 7 since they do not contain
any tracks directly. Folder 5 is not recognized at all since it is at the fourth
level.
To remove the USB device, press the SRC button (6) to switch to another
mode and then remove the USB device from the USB jack.
13
VM8022
File Playback
When a disc or device (SD, USB) containing individual music, video and/or
photo files is inserted, the following screen appears:
Folder Name
File Name
Folder List
File List
Category List
The category, folder or file list is displayed on screen with the name of the
file/folder being played displayed on top. The item currently selected will
appear highlighted.
You can change which type of items appear for selection on the screen
using the following buttons:
AUDIO
PICTURE
VIDEO
1. Use the
/
cursor buttons to highlight the media type, and then press
ENTER to confirm.
2. Use the
/
cursor buttons to enter a folder list and the
/
cursor
buttons to select a folder.
3. Use the
/
cursor buttons to enter a file list and the
/
cursor
buttons to select a file.
4. Press ENTER to play the file or (stop) to return.
For PICTURE, press the >|| button (8) to play a slide show of any pictures
on the media. Press PROG to select how the next photo is displayed.
14
VM8022
CARE AND MAINTENANCE
DVD Player
Disc Care and Handling
The following guidelines will help you extend the life of your DVD player:
Dirt, dust, scratches and warpage can cause skips in the playback and
deterioration of sound quality. Please follow these guidelines to take care of
your compact discs.
1. When cleaning the vehicle interior, do not get water or cleaning fluids on
the unit.
2. The DVD player will not operate properly in extreme hot/cold or under
damp conditions. In case of such conditions, wait until the vehicle
interior reaches a normal temperature or any condensation on the disc
player lens has evaporated before using the player.
3. Always remove the disc when the player is not in use.
4. The unit is designed with a vibration dampening disc mechanism to
minimize interruption of disc play due to normal vibration in a moving
vehicle. However, occasional sound skips may occur when driving on
very rough roads. This will not scratch or damage the disc, and normal
play will resume when the rough conditions cease.
1. Do not touch the disc surface.
2. Never use chemicals such as record sprays or household cleaners to
clean discs, as they can irreparably damage the disc’s surface.
3. Discs should be kept in their storage cases when not in use.
4. Do not expose discs to direct sunlight, high temperatures or high
humidity for long periods.
CD-R and CD-RW Capability
Depending on media type and method of "recording/burning", some CD-R/
RWs may be incompatible with this unit. After "recording/burning", the
session must be closed. Please refer to your software's recommended
procedures for closing a disc/session. Review your recording software to
familiarize yourself with the correct "recording/burning" procedures. We
5. Carefully wipe fingerprints, dust and dirt from the disc’s playing surface
with a soft cloth. Wipe in a straight motion from the inside to the outside
of the disc.
6. Do not stick paper, tape or disc labels on disc surfaces, as internal
damage may occur.
TM
TM
recommend using the latest versions of ROXIO or NERO burning
software.
In addition, this unit will only recognize the CDDA (Compact Disc Digital
Audio), .MP3 and .WMA formats "recorded / burned" onto a CD-R/RW. This
unit does not support .WAV, .OGG or other formats.
15
VM8022
TROUBLESHOOTING
Problem
Cause
Corrective Action
Does not operate (dis-
play does not light)
No power to yellow wire; no
power to red wire
Check connection with test light; check
vehicle fuse with test light
Fuse blown
Fuse blown
Replace fuse
No power to unit
Check/replace fuse
No/low audio output
Improper audio output connec- Check wiring and correct
tion
Volume set too low
Speakers damaged
Increase volume level
Replace speakers
Heavily biased volume balance Adjust the channel balance to the center
position
Speaker wiring is in contact with Insulate all speaker wiring connections
metal part of car
Blows fuses
No image
Power wire shorting to ground Make sure wire is not pinched
Speaker wires shorting to
ground
Make sure wire is not pinched
Incorrect fuse; fuse too small
Install fuse of correct rating
Incorrect connection to parking Check Parking SW wiring and correct
brake wire
Parking SW is connected but
parking brake is not engaged
Stop vehicle in safe place and apply
parking brake
Flashing image or inter- DVD is not compatible with cur- Change setup to accommodate disc
ference appears on
screen
rent TV system settings
Improper video signal connec- Check wiring and correct
tions
Prolonged image or
improper height/width
ratio display
Improper aspect ratio setup
Use correct ASPECT RATIO setting
Disc does not play back Disc is warped or scratched
Disc is dirty or wet
Use disc in good condition
Clean disc with soft cloth
Clean laser pickup with cleaning disc
Use compatible disc
Laser pickup is dirty
Incompatible disc is used
Disc rating exceeds RATING
limit
Change RATING settings to lower
restriction
Disc region code is not compati- Use disc with proper region code
ble with unit
Disc is inserted upside down
Insert disc with label side up
Use original disc
Image blurred, distorted, Disc is illegally copied
or dark
16
VM8022
SPECIFICATIONS
Monitor
CEA Power Ratings
Screen Size. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.0" (Measured diagonally)
Active Area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88mm x 50mm
Screen Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Digital TFT Panel
Resolution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 480 (W) X 272 (H) sub pixels
Dot Pitch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.061 (H) x 0.183 (V)
Contrast Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100:1
Brightness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .200 cd/m2
General
Auxiliary Input Impedance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10k
Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 to 16VDC, negative ground
Power Antenna (Blue) . . . . . . . . . . . . . . . . . . . . . . . . .500mA max, current limited protection
Operating Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-20C ~ 65C
Fuse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15-amp, mini ATO type
DIN Chassis Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.0 DIN (Double DIN)
Power Output . . . . . . . . . . . . . . . .13 watts RMS X 4 channels into 4-ohms @ < 1% THD+N
Signal to Noise Ratio. . . . . . . . . . . . . . . 70dBA below reference (reference: 1 watt, 4-ohms)
Frequency Response . . . . .20Hz to 20kHz (-3dB), Auxiliary input used as source reference
Reference Supply Voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14.4VDC
DVD/CD Player
*Specifications subject to change without notice.
Compatible Disc Media . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DVD + R / RW and CD-R / RW
Compatible Media Formats . . . . . . . . . . . . . . . . . . . . CD-DA, MP3, WMA, VCD, SVCD, AVI,
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . MPEG1 / 2, XviD, DivX and Kodak picture CD (JPEG)
Signal to Noise Ratio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .>95dBA
Dynamic Range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . >95dB
Frequency Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20Hz to 20 kHz, -3dB
Channel Separation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . > 60dB @ 1 kHz
Video
Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .NTSC, PAL (auto-detection)
Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Vp-p (75-ohm)
Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Vp-p (75-ohm)
FM Tuner
Tuning Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87.5MHz - 107.9MHz
Mono Sensitivity (-30dB). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10dBf
Quieting Sensitivity (-50dB). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15dBf
Alternate Channel Selectivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70dB
Signal to Noise Ratio @ 1 kHz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58dB
Image Rejection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75dB
Stereo Separation @ 1 kHz. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . >27dB
Frequency Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30Hz - 13 kHz, -3dB
AM Tuner
Tuning Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 530 kHz - 1720 kHz
Sensitivity (-20dB). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15uV
Signal to Noise Ratio @ 1 kHz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50dB
Frequency Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50Hz - 2kHz, -3dB
17
VM8022
18
Limited Warranty
DO NOT RETURN THIS PRODUCT TO THE STORE
CD or Multimedia Radios/Headunits
Audiovox Electronics Corporation (“the Company”) is committed to
quality and customer service, and are pleased to offer you this
Warranty. Please read it thoroughly and contact the Company at 1-800-
323-4815 with any questions.
Limitations
THE EXTENT OF THE COMPANY'S LIABILITY UNDER THIS WARRANTY
IS LIMITED TO THE REPAIR OR REPLACEMENT PROVIDED ABOVE AND,
IN NO EVENT, SHALL THE COMPANY'S LIABILITY EXCEED THE
PURCHASE PRICE PAID BY PURCHASER FOR THE PRODUCT.
Who is covered?
The Company extends this warranty to the original retail purchaser of products
purchased through an authorized Audiovox retailer in the U.S.A., Puerto Rico or
Canada. This warranty is not transferable or assignable. Proof of purchase is
required in the form of an original sales receipt.
This Warranty is in lieu of all other express warranties or liabilities. ANY IMPLIED
WARRANTIES,
INCLUDING
ANY
IMPLIED
WARRANTY
OF
MERCHANTABILITY, SHALL BE LIMITED TO THE DURATION OF THIS
WRITTEN WARRANTY. ANY ACTION FOR BREACH OF ANY WARRANTY
HEREUNDER
INCLUDING
ANY
IMPLIED
WARRANTY
OF
What is covered?
MERCHANTABILITY MUST BE BROUGHT WITHIN A PERIOD OF 24
MONTHS FROM DATE OF ORIGINAL PURCHASE. IN NO CASE SHALL THE
COMPANY BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL
DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS
OR IMPLIED, WHATSOEVER. No person or representative is authorized to
assume for the Company any liability other than expressed herein in connection
with the sale of this product.
The Company warrants that should this product or any part thereof, under normal
use, be proven defective in material or workmanship within 12 months from the
date of original purchase, such defect(s) will be repaired or replaced with a new or
reconditioned product (at the Company's option) without charge for parts and
repair labor.
What is not covered?
This Warranty does not cover the following:
Some states do not allow limitations on how long an implied warranty lasts or the
exclusion or limitation of incidental or consequential damage so the above
limitations or exclusions may not apply to you. This Warranty gives you specific
legal rights and you may also have other rights which vary from state to state.
•
Damage incurred during shipping or transporting the product to the
Company or a service center
•
•
•
•
•
Elimination of car static or motor noise
Defects in cosmetic, decorative or non-operative structural parts
Correction of antenna problems
Costs incurred for installation, removal or reinstallation of the product
Consequential damage to compact discs, USB devices, digital media
cards, accessories or vehicle electrical systems
Obtaining Warranty Service
•
To obtain repair or replacement within the terms of this Warranty,
call 1-800-323-4815 for the location of a warranty station serving
your area.
•
•
•
Damage caused by improper installation, mishandling, misuse, neglect,
accident, blown fuse, battery leakage, theft or improper storage
Products whose factory serial number/bar code label(s) or markings
have been removed or defaced
Damage resulting from moisture, humidity, excessive temperature,
extreme environmental conditions or external natural causes
•
You must prepay the initial shipping charges to the Company.
The Company will pay the return shipping charges for all
warranteed products returned to an address within the U.S.A.,
Puerto Rico or Canada.
Please package the product securely to avoid shipping damage.
We recommend using a carrier that provides tracking service to
prevent lost packages. Lost or damaged packages are not
covered by this warranty.
•
•
Please review the “Care and Maintenance” section of your Installation
and Operation Manual for additional information regarding the proper
use of your product.
Provide a detailed description of the problem(s) for which you
require service.
Audiovox Electronics Corporation
Hauppauge, NY 11788
Technical Assistance: 1-800-323-4815
© 2007 Audiovox
Ver. 042007
Printed in China
|